CR1701A
iJuke
Instruction Manual
MUTE
VOL +
albums
VOL -
extras
www.crosleyradio.com
IMPORTANT SAFETY INSTRUCTION
PLEASE READ CAREFULLY ALL THE FOLLOWING IMPORTANT SAFEGUARDS
THAT ARE APPLICABLE TO YOUR EQUIPMENT
1.
2.
3.
4.
5.
Read Instructions - All the safety and operating instructions should be read before the product is operated.
Retain instructions - The safety and operating instructions should be retained for future reference.
Heed Warnings - All warnings on the product and in the operating Instructions should be adhered to.
Follow Instructions - All operating and use instructions should be followed.
Cleaning - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.Use
a damp cloth for cleaning.
6. Attachments - Do not use attachments not recommended by the product manufacturer as they may cause hazards.
7. Water and Moisture - Do not use this product near water - for example, near a bath tub, wash bowl, kitchen sink, or
laundry tub; in a wet basement; or near a swimming pool; and the like.
8. A product and cart combination should be moved with care. Quick stops, excessive force, and uneven
surfaces may cause the product and cart combination to overturn.
9. Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable
operation of the product and to protect it from overheating, and these openings must not be blocked
or covered, The openings should never be blocked by placing the product on a bed, sofa, rug, or
other similar surface. This product should not be placed in a built - in installation such as a bookcase
or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to.
10. Power Sources - This product should be operated only from the type of power source indicated on the marking label,
if you are not sure of the type of power supply to your home. Consult your product dealer or local power company.For
products intended to operate from battery power, or other sources, refer to the operating instructions.
11. Grounding or Polarization - This product may be equipped with a polarized alternating-current line plug (a plug having
one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you
are unable to insert the plug fully into the outlet try reversing the plug, If the plug should still fail to fit, contact your
electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.
12. Power - Cord Protection - Power - supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them, paying particular attention to
cords at plugs, convenience receptacles, and the point where they exit from the product.
AC
13. Lightning - For added protection for this product during a lightning storm, or when it is left
Polarized Plug
unattended and unused for long periods of time, unplug it from the wall outlet and disconnect
the antenna or cable system. This will prevent damage to the product due to lightning and power - line surges.
14. Power Lines - An outside antenna system should not be located in the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system,
extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
15. Overloading - Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result
in a risk of fire or electric shock.
16. Object and Liquid Entry - Never push objects of any kind into this product through openings as they may touch
dangerous voltage points or short - out parts that could result in a fire or electric shock. Never spill liquid of any kind
on the product.
17. Servicing - Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified service personnel.
18. Damage Requiring Service - Unplug this product from the wall outlet and refer servicing to qualified service personnel
under the following conditions;
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the operating instructions. Adjust only those controls that
are covered by the operating instructions as an improper adjustment of other controls may result in damage and
will often require extensive work by a qualified technician to restore the product to its normal operation.
e. If the product has been dropped or damaged in any way.
f. When the product exhibits a distinct change in performance - this indicates a need for service.
19. Replacement Parts - When replacement parts are required, be sure the service technician has used replacement
parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions
may result in fire, electric shock, or other hazards.
20. Safety Check - Upon completion of any service or repairs to this product, ask the service technician to perform safety
checks to determine that the product is in proper operating condition.
21. Wall or ceiling Mounting - The product should be mounted to a wall or ceiling only as recommended by the manufacturer.
22. Heat - The product should be situated away from heat sources such as radiators. Heat registers, stoves, or other
products (including amplifiers) that produce heat.
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful intereference to radio or
television reception, which can be determined by turning the equipment off and on , the user is encouraged to try to correct
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio TV technician for help.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE. DO NOT REMOVE COVER.
PILOT LAMPS SOLDERED IN PLACE. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lighting flash with
arrowhead symbol, within
an equilateral triangle, is
intended to alert user to
the presence of uninsulated
"dangerous voltage" within
the product's enclosure
that may be of sufficient
magnitude to constitute
risk of electric shock
to persons.
CAUTION: TO REDUCE
THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE
COVER (OR BACK). NO
USER - SERVICEABLE
PARTS INSIDE. REFER
SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The exclamation point
within an equilateral
triangle is intended to
alert user to the
presence of important
operating and
maintenance (servicing)
instruction in the
literature accompanying
the appliance.
Specification
Power Source
:
Power Consumption
Speaker
:
:
Input AC120V 60Hz
Output DC15V 1100mA
25W
Dynamic type 4” 4 Ohm x 2
* DESIGN AND SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.
2
Welcome
Thank you for purchasing the Crosley iJuke
(CR1701A).Before operating this unit, please
read this manual thoroughly and retain it for
future reference.
About This Manual
Instructions in this manual describe the control
functions of the iJuke (CR1701A).
Table of Contents
Getting Started
Control Locator...................... 4-5
Unpacking.............................. 6
Set Up.................................... 6
Basic Operation
Using your iJuke.................... 7
Remote Control...................... 8
Lights ..................................... 8
Connecting Optional Equipment
External Outputs.................... 9
Auxiliary Inputs....................... 9
General
Troubleshooting .................... 10
3
Control Locator
Unit Controls
1
2
3
4
5
6
7
8
9
10
11
12
13
Power Indicator
Power On/Off
Lights On/Off
Universal Dock
Remote Sensor
Speakers
Mute Indicator
Volume Up
Volume Down
Remote Storage
Auxiliary Input (Aux In)
Speaker Jacks
Internal / External Speaker Switch
(EXT. / INT.)
14 Stage Light Stop & Run Switch
15 DC Jack
1
2
3
7
MUTE
8
9
VOL +
albums
VOL -
extras
4
5
6
6
10
11
12
13
14 15
4
Control Locator
22
Remote Controls
16
16
17
18
19
20
21
22
23
24
25
26
27
Power
Backward Skip
Play / Pause
Up Select
Down Select
Repeat
Select
Menu
Mute
Forward Skip
Volume Up
Volume Down
23
POWER
MENU
MUTE
24
17
18
SELECT
25
UP ARROW
VOL +
26
19
DN ARROW
20
REPEAT
VOL -
27
21
5
Getting Started
Unpacking
1
Remove unit from box and remove all packing
materials.
Note: Save the box and packing materials in case the
unit needs to be transported or returned.
2
Remove plastic safety cover from A/C plug.
3
Remove tie from A/C cord.
4
Remove tie from A/C adapter.
Set Up
1
Check the carton for all the parts shown.
Remote Control
4
Remove battery cover from remote control and
install 2 AAA batteries (not included). Note the
correct battery orientation.
5
Place the iJuke on a flat surface.
A/C adapter
Auxiliary cable
2
3
Plug the small end of the AC adapter into the
DC Jack on the back of the unit.
Plug the adapter pack into an appropriate outlet.
Note: The speakers in the iJuke are shielded which
limits the possibility of video interference if placed
near a computer or television monitor.
6
Basic Operation
Using your iJuke
The iJuke features the Universal Dock that uses
dock adapters that come with newer iPod models.
Before inserting your iPod, you will need to install
the correct dock adapter. By using the correct dock
adapter, you can insert any iPod with a dock
connector. While docked, the iJuke will also charge
your iPod. To connect your iPod, follow the steps
below. If you’re iPod doesn’t have a dock connector,
you can connect it to the unit by using the Auxiliary
Cable that is supplied.
1
Insert the correct dock adapter that fits your
iPod. Your iPod should fit snugly into the correct
adapter. Gently press the adapter until it snaps
firmly in place.
2
Connect your iPod as shown in the illustration
below.
3
Press the Power button to turn iJuke on.
4
Browse your iPod for songs and press the
Play/Pause button. Your music should begin to
play.
5
Adjust the volume to your desired listening level.
6
To remove the dock adapter, push your fingernail
into the slot in the back of the adapter and lift
up.
Note: If your iPod does not have a dock connector, use
the supplied Auxiliary Cable and hook your iPod
to the Auxiliary Input (Aux In) jack on the back
of the unit.
7
Basic Operation
Remote Control
Included with your iJuke is a full function remote
control. It allows you to control the main power and
volume of the iJuke and also gives you complete
control of your iPod including menu functions on
most iPod models. See below for a complete list of
the remote functions.
Lights
1
To turn on the lights, press the Light button on
the front of the unit.
2
Adjust the Stage Light Switch to Stop or Run to
make the Eternity Lights constant or in motion.
Power
– The POWER button turns the iJuke
on/off. When docked, pressing the
power button will also turn your iPod
on/off with the unit.
Menu
– The MENU button allows you to access
the menus on your iPod.
Mute
– The MUTE button mutes the volume
of the iJuke.
– Pressing the FORWARD SKIP button
once will take you to the beginning of
the next song on your iPod. You can
press and hold it to search forwards
through the song that is playing.
– Pressing the BACKWARD SKIP button
once takes you to the beginning of the
song your are listening to. Press it
twice to go to the beginning of the
previous song. You can also press and
hold it to search backwards through
the song that is playing.
– The PLAY/PAUSE button is used to
pause the song that is playing.
Pressing it twice resumes playback.
Up Select – The UP SELECT button moves
upwards through the menu selections.
DN Select – The DOWN SELECT button moves
downwards through the menu
selections.
Select
– The SELECT button enters your
selections from the menus.
Repeat
– The REPEAT button allows you to
repeat selected songs on applicable
iPod models.
Vol +
– The VOLUME UP button Increases
your volume level.
Vol – The VOLUME DOWN button
decreases your volume level.
POWER
MENU
MUTE
SELECT
UP ARROW
DN ARROW
VOL +
REPEAT
VOL -
8
Connecting Optional Equipment
External Outputs
The iJuke is equipped with external speaker outputs
which will allow you to hook up external speakers.
1
2
The speaker jacks for external speakers are 4
ohm jacks and are located on the back of the
unit. Beside the speaker jacks is the external /
internal speaker switch which is labeled (EXT.
/ INT.) When using external speakers, this switch
must be switched to the EXT. position. Doing
this turns off the internal speakers in the unit
and redirects to power to the external speakers.
Auxiliary Inputs
You can connect external audio devices such as CD
Players or other MP3 players by using the Auxiliary
Input (Aux In) jack and the supplied Auxiliary cable.
To connect an external devise, follow the directions
below.
1
Connect one end of the supplied Auxiliary Cable
to the Aux In jack on the back of your unit.
2
Connect the other end of the cable to the Audio
Out Jack or Headphone Jack of your external
component.
If you decide not to use the external speakers,
be sure the switch is on INT. position or the
internal speakers will not work.
Note: If your external component doesn’t have a 3.5mm
output jack or headphone jack, you will need a
different cable to make the connection. Check
your local electronics retailer for different cable
options.
3
Begin play on the external component and adjust
the volume of the iJuke to your desired listening
level.
4
See the owner’s manual for your external
component for information on its operations.
Auxiliary cable
9
General
Troubleshooting
There’s no power?
1
The AC adapter is not connected. Check to
make sure it is plugged in correctly.
There’s no sound?
1
Make sure the mute function is turned off.
2
Check that the volume is turned up by pressing
Volume Up button on remote.
3
Make sure the External / Internal Speakers
switch is on INT.
(Unless you are using external speakers,
in which case it should be on EXT.)
4
Check to make sure power is turned on.
5
Make sure the Hold switch on your iPod is in
the off position.
6
Check that the iPod is not paused.
Remote not working?
1
Replace batteries.
2
Point remote towards remote sensor when using.
10
LIMITED MANUFACTURERS WARRANTY
Crosley Radio, Inc. warrants the product to be free from defects in material and
workmanship under normal use for a period of one year from the original date of
purchase. This warranty is not transferable. If the product is determined to be defective
during the warranty period, the unit will be repaired or replaced at Crosley Radio’s sole
discretion. This warranty covers manufacturing defects and normal consumer use and
does NOT cover damage or failure as a result of abuse, accident, alterations, misuse,
neglect, abnormal wear and tear, inadequate maintenance, commercial or unreasonable
use, damage caused by power surges, mishandling, accident, acts of God or attempted
repair by an unauthorized service agent. Also not covered are cosmetic damages,
cords and antennas.
Should this product fail to function in a satisfactory manner, it is best to first return it
to the store or retailer where it was originally purchased. If additional service is still
needed, the original purchaser must FIRST contact our offices to obtain an RA (Return
Authorization) Number.
TO OBTAIN AN RA NUMBER
CALL: 1.888.CROSLEY
(1.888.276.7539)
Send the unit prepaid to the address below in the original packaging (or reasonable
substitute to prevent damage). Clearly mark your RA number on the outside packaging
and include the original sales receipt (or a copy) indicating date of purchase, amount
paid, and place of purchase. You must also include your full name, shipping address
and daytime contact number. Please include a check or money order in the amount
of $19.95, made payable to Crosley Radio, to cover handling and return shipping
charges. Returned products will not be shipped to PO Boxes. Crosley Radio will not
be responsible for delays or unprocessed claims resulting from a purchaser’s failure
to provide any or all of the necessary information.
CROSLEY RADIO
ATTN: RETURNS DEPT
2001 PRODUCTION DRIVE
Louisville, KY 40299
For additional support: Crosley Radio Consumer Service Department
24 hours a day / 7 days a week
Telephone: 1.888.CROSLEY (1.888.276.7539)
There are no express warranties except as listed above.
The purchaser’s bill of sale is the only proof of warranty entitlement.
This warranty gives the purchaser specified legal rights in addition to any rights which
may vary from state to state.
In accordance with the “Moss-Magnuson Warranty Act” of July 10, 1975, this is termed
a “limited warranty” which in no way compromises Crosley Radio’s high standards of
quality and workmanship.
910-283500-0020-200