Yamaha TSX-W80 Owner`s manual

U
DESKTOP AUDIO SYSTEM
SYSTEME AUDIO DESKTOP
TSX-W80
OWNER’S MANUAL
MODE D’EMPLOI
IMPORTANT SAFETY INSTRUCTIONS
1 Read these instructions.
CAUTION
RISK OF ELECTRIC SHOCK DO
NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
2
3
4
5
6
7
8
9
• Explanation of Graphical Symbols
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert you to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral
triangle is intended to alert you to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
10
11
12
13
IMPORTANT
14
Please record the serial number of this unit in the space
below.
MODEL:
Serial No.:
The serial number is located on the rear of the unit. Retain
this Owner’s Manual in a safe place for future reference.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has
two blades and a third grounding prong. The wide blade
or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
Only use attachments/accessories specified by the
manufacturer.
Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
Unplug this apparatus during lightning storms or when
unused for long periods of time.
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug
is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to rain
or moisture, does not operate normally, or has been
dropped.
We Want You Listening For A Lifetime
Yamaha and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out
of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without
annoying blaring or distortion – and, most importantly, without affecting your sensitive hearing. Since hearing
damage from loud sounds is often undetectable until it is too late, Yamaha and the Electronic Industries
Association’s Consumer Electronics Group recommend you to avoid prolonged exposure from excessive
volume levels.
i En
IMPORTANT SAFETY INSTRUCTIONS
FCC INFORMATION (for US customers)
1 IMPORTANT NOTICE: DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved
by Yamaha may void your authority, granted by the
FCC, to use the product.
2 IMPORTANT: When connecting this product to
accessories and/or another product use only high
quality shielded cables. Cable/s supplied with this
product MUST be used. Follow all installation
instructions. Failure to follow instructions could void
your FCC authorization to use this product in the
USA.
3 NOTE: This product has been tested and found to
comply with the requirements listed in FCC
Regulations, Part 15 for Class “B” digital devices.
Compliance with these requirements provides a
reasonable level of assurance that your use of this
product in a residential environment will not result in
harmful interference with other electronic devices.
This equipment generates/uses radio frequencies and,
if not installed and used according to the instructions
found in the users manual, may cause interference
harmful to the operation of other electronic devices.
Compliance with FCC regulations does not guarantee
that interference will not occur in all installations. If
this product is found to be the source of interference,
which can be determined by turning the unit “OFF”
and “ON”, please try to eliminate the problem by
using one of the following measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch
(circuit breaker or fuse) circuits or install AC line
filter/s.
In the case of radio or TV interference, relocate/
reorient the antenna. If the antenna lead-in is 300 ohm
ribbon lead, change the lead-in to coaxial type cable.
If these corrective measures do not produce
satisfactory results, please contact the local retailer
authorized to distribute this type of product. If you can
not locate the appropriate retailer, please contact
Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe
Ave., Buena Park, CA 90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
– Reorient or relocate the receiving antenna
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
This equipment compiles with FCC/IC radiation exposure
limits set forth for uncontrolled equipment and meets the
FCC radio frequency (RF) Exposure Guidelines in
Supplement C to OET65 and RSS-102 of the IC radio
frequency (RF) Exposure rules. This equipment has very
low levels of RF energy that it deemed to comply without
maximum permissive exposure evaluation (MPE). But it is
desirable that it should be installed and operated with at
least 20 cm and more between the radiator and person’s
body (excluding extremities: hands, wrists, feet and
ankles).
There is a chance that placing this unit too close to a
CRT-based (Braun tube) TV set might impair picture
color. Should this happen, move this unit away from the
TV set.
FCC WARNING
Change or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
This transmitter must not be co-located or operated in
conjunction with any other antenna or transmitter.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to
wide slot and fully insert.
This Class B digital apparatus complies with Canadian
ICES-003.
ii En
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
Install this unit in a well ventilated, cool, dry, clean
place - away from direct sunlight, heat sources,
vibration, dust, moisture and cold. For proper
ventilation, allow the following minimum clearances.
Top: 15 cm (6 in)
Rear: 10 cm (4 in)
Sides: 10 cm (4 in)
Locate this unit away from other electrical
appliances, motors, or transformers to avoid
humming sounds.
Do not expose this unit to sudden temperature
changes from cold to hot, and do not locate this unit
in an environment with high humidity (i.e. a room
with a humidifier) to prevent condensation inside this
unit, which may cause an electrical shock, fire,
damage to this unit, and/or personal injury.
Avoid installing this unit where foreign object may
fall onto this unit and/or this unit may be exposed to
liquid dripping or splashing. On the top of this unit,
do not place:
– Other components, as they may cause damage
and/or discoloration on the surface of this unit.
– Burning objects (i.e. candles), as they may cause
fire, damage to this unit, and/or personal injury.
– Containers with liquid in them, as they may fall
and liquid may cause electrical shock to the user
and/or damage to this unit.
Do not cover this unit with a newspaper, tablecloth,
curtain, etc. in order not to obstruct heat radiation. If
the temperature inside this unit rises, it may cause
fire, damage to this unit, and/or personal injury.
Do not plug in this unit to a wall outlet until all
connections are complete.
Do not operate this unit upside-down. It may
overheat, possibly causing damage.
Do not use force on switches, knobs and/or cords.
When disconnecting the power cable from the wall
outlet, grasp the plug; do not pull the cable.
Do not clean this unit with chemical solvents; this
might damage the finish. Use a clean, dry cloth.
Only voltage specified on this unit must be used.
Using this unit with a higher voltage than specified is
dangerous and may cause fire, damage to this unit,
and/or personal injury. Yamaha will not be held
responsible for any damage resulting from use of this
unit with a voltage other than specified.
To prevent damage by lightning, keep the power
cable disconnected from a wall outlet or this unit
during a lightning storm.
Do not attempt to modify or fix this unit. Contact
qualified Yamaha service personnel when any
service is needed. The cabinet should never be
opened for any reasons.
iii En
15 When not planning to use this unit for long periods of
time (i.e. vacation), disconnect the AC power plug
from the wall outlet.
16 Be sure to read the “TROUBLESHOOTING” section
on common operating errors before concluding that
this unit is faulty.
17 Before moving this unit, press
to set the system to
off, and disconnect the AC power plug from the wall
outlet.
18 Condensation will form when the surrounding
temperature changes suddenly. Disconnect the power
cable from the outlet, then leave this unit alone.
19 When using this unit for a long time, this unit may
become warm. Turn the system off, then leave this
unit alone for cooling.
20 Install this unit near the wall outlet and where the AC
power plug can be reached easily.
21 The batteries shall not be exposed to excessive heat
such as sunshine, fire or the like. When you dispose
of batteries, follow your regional regulations.
22 Be sure to use the AC adaptor supplied with this unit.
Using an AC adaptor other than the one provided
may cause fire or damage to this unit.
This unit is not disconnected from the AC power source
as long as it is connected to the wall outlet, even if this
unit itself is turned off by . In this state, this unit is
designed to consume a very small quantity of power.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR
MOISTURE.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Radio waves may affect electro-medical devices.
Do not use this unit near medical devices or inside
medical facilities.
Do not use this unit within 22 cm (9 in) of persons with a
heart pacemaker implant or defibrillator implant.
PREPARATION
LISTENING TO RADIO STATIONS ................. 8
TROUBLESHOOTING......................................... 9
SPECIFICATIONS.............................................. 11
Français
NAMES OF PARTS AND THEIR FUNCTIONS
..................................................................................2
BASIC FUNCTIONS..............................................4
LISTENING TO iPod™ AND EXTERNAL
SOURCES ...............................................................6
■ Features
– Hi-quality iPod/iPhone, radio and external device playability.
– Firm bass sound and spacious stereo sound from 2.1 ch powered speaker (tweeter × 2, woofer × 1), SRBass™ (Yamaha Swing Radiator Bass technology) and DSP in a compact unit.
– Easy user-intuitive interface by buttons with Guide LED and knob dials.
■ Yamaha yAired
Real-time uncompressed music transfer without sound degradation is realized by Yamaha original digital wireless
transfer technology, yAired. You can also control system on/off and volume with the iPod by yAired.
y
You can use a subwoofer wirelessly with the Wireless subwoofer kit (SWK-W10, etc., sold separately). Refer to the owner’s
manual of the SWK-W10 for details.
■ About this manual
• This unit is iPod and also iPhone-compatible. “iPod” described in this manual may also refer to “iPhone”.
• This manual describes how to operate this unit using buttons on the unit. Some of these operations are also
available using the remote control.
■ Supplied accessories
Remote control
AC adaptor
(DC 15 V, 2.66 A,
model number:
NU40-2150266-I3)
Power cable
Transmitter
Indoor FM antenna
YIT-W11TX
AM loop antenna
■ Using the remote control
English
CONTENTS
■ Replacing the battery in the remote
control
CR2025
battery
Within 6 m
(20’)
1 En
NAMES OF PARTS AND THEIR FUNCTIONS
■ Front and top panel
When charging an iPod,
1 Connect the iPod to the transmitter.
2 Set the iPod connected to the transmitter to the
charging cradle.
1
: Press to turn the system on/off.
Time is displayed even when the system is off.
y
• Press and hold
on the top of the unit for more than 3
seconds to set the system to standby mode. All the
information on the front panel display is not displayed
in standby mode. This can reduce power consumption.
To cancel standby mode, press .
• Even in system off/standby mode, the alarm function is
available.
2 TIMER: Timer setting (☞ P. 5)
8 PRESET: Storing your favorite 5 FM and 5 AM
stations (☞ P. 8)
9 SNOOZE/SLEEP (☞ P. 5)
0 DIMMER: Setting brightness of the front panel
A (auto) 3 (brightest) 2 1 (darkest) back to A
y
When A (auto) is set, the brightness of the front panel is
adjusted automatically depending on the brightness of the
room.
A MEMORY (☞ P. 7, ☞ P. 8)
3 ALARM: Alarm on/off (☞ P. 4)
B TUNING (☞ P. 8)
4 SET: Alarm setting (☞ P. 4)
C FM, AM: Switching FM/AM
5 Front panel display
D Charging cradle: For charging an iPod
6 SOURCE: iPod, AUX, RADIO
E Illumination sensor: Measuring surrounding
illuminance. Do not cover this sensor.
7 VOLUME: Volume control
2 En
NAMES OF PARTS AND THEIR FUNCTIONS
English
■ Rear panel
15V
: Connect supplied
AC adaptor and power cable.
Antenna terminal
(See below.)
AUX: Connect an external
device. (☞ P. 7)
ALARM TYPE switch (☞ P. 4)
TONE CONTROL: Control Bass
and Treble.
CLOCK switch (☞ P. 4)
■ Connecting antennas
Indoor FM
antenna
(supplied)
AM loop antenna (supplied): Connect the black cord
to GND, and the white to AM ANT.
Notes
• The antenna should be stretched
out.
• If radio reception is poor,
change the height, direction, or
placement of the antenna.
• If you use outdoor antennas
instead of the supplied antennas,
reception will be better.
Ground (GND terminal):
For minimum interference, connect the antenna GND terminal
to a good earth ground. A good earth ground is a metal stake
driven into moist earth.
■ Remote control
Source buttons: iPod, AUX,
RADIO. RADIO button switches
FM/AM when SOURCE is set to
RADIO.
Infrared signal transmitter
iPod control buttons
: System on/off
SLEEP: Sleep setting
(☞ P. 5)
ALARM: Alarm on/off
(☞ P. 4)
VOLUME: Volume control
TUNING: Tuning radio
(☞ P. 8)
PRESET: Select the preset radio
station. (☞ P. 8)
Battery insulation sheet:
Remove before using.
3 En
OPERATION
BASIC FUNCTIONS
Adjusting the clock
1 Set CLOCK to SET.
2 Set the time with TUNING.
3 Set CLOCK to LOCK.
Note
Rear panel
Front panel display
flashes.
The time settings are lost approximately one
week after unplugging the unit.
Alarm setting
This unit can play back iPod/radio and/or beep sound at the set time.
■ Setting the alarm time and sound
1 Press SET.
2 Set the alarm time with
TUNING.
3 Set ALARM TYPE.
Alarm indicator (
)
and front panel display
flashes.
Rear panel
(As required)
• SOURCE+BEEP: selected source
(played back from 3 minutes before
the alarm time) and beep sound
(played back at the alarm time)
• SOURCE: selected source
• BEEP: beep sound only
When you select SOURCE+BEEP or
SOURCE, select:
• iPod: this unit resumes the song you
listened to last time.
• RADIO: this unit plays back the
radio station you listened to last time.
4 Set the alarm volume.
5 Press SET.
Alarm is set and the alarm indicator
(
) lights up.
Note
When iPod is selected as a source, set the iPod
to the charging cradle (☞ P. 2). If iPod is not
set at the alarm time, beep sound is played back.
■ Switching the alarm on/off
Switch on/off the alarm function.
When the alarm is on, the alarm
indicator (
) lights up and alarm
time is displayed for a while.
4 En
BASIC FUNCTIONS
English
Operations during playing back alarm sound
At the set time, alarm sound plays back. During playback, operations below are available.
■ Using the snooze function
Press SNOOZE/SLEEP.
The alarm sound stops and resumes
after 5 minutes.
■ Stopping the alarm
Press ALARM or
.
y
• Unless you stop the alarm, the alarm stops
after 60 minutes automatically.
• When you stop the alarm, the alarm time
setting, etc., is saved for convenient use next
time.
Sleep setting
You can set the time to turn off the system automatically when sleep is set to on.
Select the sleep time.
You can set 30, 60, 90 or 120 minutes.
When the sleep function is on, the
sleep indicator (
) lights up.
Press repeatedly.
Sleep indicator (
) and front
panel display flash.
y
To cancel the sleep, press SNOOZE/SLEEP.
Timer setting
You can set the countdown timer.
1 Press TIMER.
2 Set the countdown time with
TUNING.
Front panel
display flashes.
Countdown
starts.
You can set the time,
• 1 to 15 minutes: minute steps.
• 20 to 120 minutes: 10-minute steps.
3 Press TIMER.
Countdown starts. When the timer
reaches 0, the timer sound plays back.
y
• To stop the timer sound, press TIMER.
• To cancel the timer, press TIMER during
countdown.
Note
Sleep and timer cannot be used together.
• Sleep cannot be set during countdown.
• Sleep is set to off when timer is set while
sleep is on.
5 En
LISTENING TO iPod™ AND EXTERNAL SOURCES
Listening to your iPod™
For details on compatible iPod models, refer to “SPECIFICATIONS” (☞ P. 11).
■ Playing back
1 Connect your iPod to the transmitter.
2 The status indicator blinks, and
wireless communication starts.
3 Set SOURCE to iPod.
4 Play the iPod.
y
Status indicator
iPod indicator
• You can remove the iPod whenever you want.
• When music/video in the iPod is played back, this unit
turns the system on automatically and plays back the
iPod even if the unit is system off.
• To charge the iPod, set the iPod to the charging cradle
on the unit (☞ P. 2).
• You can control the volume by the iPod.
• This unit turns the system off automatically after a
while if the iPod is turned off or removed from the
transmitter when SOURCE is set to iPod.
Notes
• If an iPod to be connected to the transmitter is playing
back, playback of iPod stops.
• When using a microwave oven, wireless LAN or
cordless telephone, etc., sound may be cut. Place the
unit away from these devices.
■ Status indicator of transmitter
LED status
The current status of the unit
Lights up green
Wireless communication between the unit and transmitter is established.
Flashes green
Flashes red
Flashes red 2 times
Off
once
Adjusting the volume level.
continuously
Connection in progress, please wait.
once
The volume of this unit is set to maximum or minimum.
2 seconds
An unsupported iPod is connected.
continuously
Error occurs. Remove the iPod from the transmitter, and connect again.
continuously
The battery of the iPod is low.
An iPod is not connected or wireless communication has not been established.
y
The iPod indicator of SOURCE on the unit:
• lights up when wireless communication has been established.
• flashes if the status is other than above.
Note
If cutting/no sound occurs, refer to “TROUBLESHOOTING” (☞ P. 9).
6 En
LISTENING TO iPod™ AND EXTERNAL SOURCES
English
Group setting
Connection between transmitter and unit is made by setting their group settings the same.
■ Group setting for the unit
1 Set SOURCE to iPod.
2 Press and hold MEMORY.
3 Set the group with TUNING.
Select A1, A2, A3, B1, B2 or B3.
B1/B2/B3 are displayed as b1/b2/b3 on
the front panel display.
Press and hold.
4 Press MEMORY.
■ Group setting for the transmitter
Set the group selection switch.
Playing back external sources
■ Playing back
Rear panel
1 Connect your portable audio
device to AUX using a
commercially available 3.5 mm
(1/8 in) mini plug cable.
Note
Turn down the volume of this unit and your
portable audio device before connection.
2 Set SOURCE to AUX.
3 Start playback on the
connected portable audio
device.
7 En
LISTENING TO RADIO STATIONS
Tuning radio stations
1 Set SOURCE to RADIO.
2 Select FM/AM.
3 For automatic tuning, press
and hold TUNING.
For manual tuning, press
TUNING repeatedly.
Note
If you tune to a station manually during FM
reception, the sound is monaural.
Presetting radio stations
You can store your favorite 5 FM and 5 AM radio stations with the preset function.
1 Tune into a favorite radio
station.
2 Press MEMORY.
3 Select the PRESET number
you want to store to.
y
To cancel the preset, press TUNING again.
4 Press MEMORY to complete.
Selecting preset radio stations
1 Set SOURCE to RADIO.
2 Select FM/AM.
3 Select the preset radio station
with PRESET.
8 En
ADDITIONAL INFORMATION
English
TROUBLESHOOTING
In case of a problem with the unit, check the following list first. If you cannot solve your problem with the
suggested solutions or if your problem is not listed below, turn off and unplug the unit, and consult the nearest
authorized Yamaha dealer or service center.
General
Problem
The system turns on but
immediately shuts off.
The speakers make no
sound.
Cause
Solution
The power cable may be connected
improperly.
Make sure the power cable is plugged into
the wall outlet firmly.
The unit may have received a strong
electrical shock such as lightning or
excessive static electricity.
Set the system to off, and disconnect the
power cable. Wait about 30 seconds,
reconnect the power cable, and turn on the
system.
The volume may be set to the minimum
level.
Adjust the volume level.
The source may be incorrect.
Select the correct source.
Sound suddenly turns off.
The sleep (☞ P. 5) may be set.
Turn on the system and play the source
again.
The unit does not operate
properly.
The unit may have received a strong
electrical shock such as lightning or
excessive static electricity, or power
supply may have dropped.
Set the system to off, and disconnect the
power cable. Wait about 30 seconds,
reconnect the power cable, and turn on the
system.
The unit may be placed too close to the
A digital or high-frequency
equipment produces noises. digital or high-frequency equipment.
Place the unit farther away from the
equipment.
The clock setting has been
cleared.
The unit is left more than one week after Plug the power cable into the wall outlet
you disconnect the power cable from the firmly, and set the clock again
wall outlet.
(☞ P. 4).
iPod does not play back at
the alarm time even if
SOURCE is set to iPod.
The iPod is not set to the charging cradle. Set the iPod to the charging cradle
(☞ P. 2).
ALARM TYPE is set to BEEP.
Set ALARM TYPE to SOURCE+BEEP or
SOURCE (☞ P. 4).
Clock flashes and the unit
cannot be operated.
CLOCK on the rear panel is set to SET,
and this unit is in clock setting mode.
Set CLOCK to LOCK.
Sound is cracked/distorted
or there is abnormal noise.
Input source volume is excessive, or
volume of this unit is excessive
(especially Bass).
Adjust volume with VOLUME, or adjust
Bass with TONE CONTROL.
iPod™
Problem
Cause
Solution
The iPod does not charge up. The iPod connecting to the transmitter is Remove the iPod connecting to the
No sound
set in the charging cradle improperly.
transmitter from the unit, then set it in the
charging cradle again (☞ P. 2).
The iPod is not connected to the
transmitter firmly.
Connect the iPod firmly.
Earphones are connected.
Remove the earphones.
Distance between the unit and the iPod is Move the transmitter closer to the unit.
too far.
9 En
TROUBLESHOOTING
Problem
No sound
Cause
Solution
The battery of the iPod is low.
Charge the iPod.
The iPod software version has not been
updated.
Download the latest iTunes software to
update the iPod software version to the
latest.
The iPod is in the process of connecting
with the unit.
Please wait for a while.
The unit and transmitter are not
connected since they are set to different
groups.
Set both the unit and transmitter to the same
group (☞ P. 7).
The unit is connected to another unit.
Select a different group by changing the
group setting of the unit and transmitter
(☞ P. 7).
Cannot change the volume
by changing the volume of
the iPod.
– The iPod is not supported by this unit. – Use the supported iPod.
– The iPod is not connected correctly.
– Connect the iPod firmly.
– The iPod software version is out of
– Update the iPod software version to the
date.
latest.
The iPod display does not
If the problem cannot be solved, even the
change by pressing the
latest software, reset the iPod.
remote control volume keys. – The transmitter is connected to several – Change the group setting (☞ P. 7).
units.
The unit is connected to another
Suddenly the speaker
produces sound even though transmitter.
an iPod is not connected.
Transmitted sound is cut.
(Status indicator of
transmitter flashes green and
iPod indicator of SOURCE
on unit flashes.)
Change the group setting (☞ P. 7).
The signal from the transmitter is
Change the way of holding, the orientation,
blocked by your body or metallic objects, or the position of the transmitter to avoid
etc.
your body or metallic objects blocking the
signal.
There is a device (microwave oven,
wireless LAN, cordless telephone, etc.)
outputting signals in the 2.4 GHz
frequency band nearby.
Place the unit away from these devices, or
turn them off. If the device is IEEE802.11ncompliant, change the channel setting of the
device so as not to affect the unit.
If noise occurs at the same frequency the This is not malfunction. If cut occurs
transmitter is using, the unit will search frequently, relocate the unit.
and move to another (unused) frequency,
which may cause sound to be cut.
Radio reception
Problem
Too much noise during
stereo broadcast.
Cause
The antenna may be connected
improperly.
Solution
Make sure the antenna is connected
properly (☞ P. 3).
The radio station you selected may be far Try manual tuning to improve the signal
from your area, or the radio wave
quality (☞ P. 8) or use a multi-channel
reception is weak in your area.
outdoor antenna.
Even with an outdoor
antenna, radio wave
reception is weak. (Sound is
distorted.)
10 En
Multipath reflection or other radio
interferences may have occurred.
Change the height, direction, or placement
of the antenna.
SPECIFICATIONS
English
Remote control
Problem
Cause
Solution
The remote control does not The remote control may be operated
outside its operation range.
work properly.
For information on the remote control
operation range, refer to “Using the remote
control” (☞ P. 1).
The remote control sensor on the unit
may be exposed to direct sunlight or
lighting (inverted fluorescent lamps).
Change the lighting or orientation of the
unit.
The battery may be worn out.
Replace the battery with a new one
(☞ P. 1).
There are obstacles between the sensor of Remove the obstacles.
the unit and the remote control.
Wireless communication is not
established when SOURCE is set to
iPod.
Play the iPod to establish wireless
communication (☞ P. 6).
SPECIFICATIONS
■ PLAYER SECTION
■ GENERAL
iPod
•
•
•
•
•
• Supported iPod .....iPod (5th generation), iPod classic, iPod
nano, iPod touch, iPhone, iPhone 3G, iPhone 3GS
AUX IN
• Input connector
............STEREO L/R: 3.5 mm (1/8 in) STEREO mini Jack
■ AMPLIFIER SECTION
• Maximum output power .......................... 4 W + 4 W + 8 W
(6 Ω 1 kHz, 10% THD)
• Driver unit ...................4 cm (1 5/8 in) full-range driver × 2
5.5 cm (2 1/8 in) woofer + SR-BASS × 1
■ TUNER SECTION
• Tuning range
FM ...................................................87.50 to 107.90 MHz
AM ......................................................... 530 to 1710 kHz
■ TRANSMITTER SECTION
• Frequency ............................................................... 2.4 GHz
• Transmission range.......................... Approx. 20 m (65.6 ft)
(without interference)
• Number of units which can be simultaneously
transmitted to ................................................... Up to 7 units
(depending on the circumstances)
Power Supply........................................... AC 120 V, 60 Hz
Power consumption .....................................................10 W
System off consumption .............................................3.5 W
Standby consumption...................................... 1.0 W or less
Dimensions (W × H × D)...................260 × 90.3 × 141 mm
(10 1/4 × 3 1/2 × 5 1/2 in)
• Weight......................................................... 1.2 kg (2.6 lbs.)
Specifications are subject to change without notice.
iPod™, iPhone™
iPod is a trademark of Apple Inc., registered in the U.S. and
other countries.
iPhone is a trademark of Apple Inc.
“Made for iPod” means that an electronic accessory has been
designed to connect specifically to iPod and has been
certified by the developer to meet Apple performance
standards.
“Works with iPhone” means that an electronic accessory has
been designed to connect specifically to iPhone and has been
certified by the developer to meet Apple performance
standards.
Apple is not responsible for the operation of this device or its
compliance with safety and regulatory standards.
11 En
Printed in China
WS68050