Clarke CESNG1 Instruction manual

ELECTRIC STAPLER & NAILER
MODEL NO: CESNG1
PART NO: 6462560
OPERATION & MAINTENANCE
INSTRUCTIONS
LS1013
INTRODUCTION
Thank you for purchasing this CLARKE product.
Before attempting to use this product, please read this manual thoroughly and
follow the instructions carefully. In doing so you will ensure the safety of yourself
and that of others around you, and you can look forward to your purchase
giving you long and satisfactory service.
GUARANTEE
This product is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt which will be
required as proof of purchase.
This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for the purpose for which it was
intended.
Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission.
This guarantee does not effect your statutory rights.
2
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
SAFETY INSTRUCTIONS
WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS,
INCLUDING THE FOLLOWING, SHOULD ALWAYS BE FOLLOWED TO REDUCE
THE RISK OF FIRE, ELECTRIC SHOCK AND PERSONAL INJURY.
WARNING: READ ALL THESE INSTRUCTIONS BEFORE OPERATING THIS
PRODUCT AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
For safe operations:
1. Keep work area clean. - Cluttered areas and benches invite injuries.
2. Consider work area environment. - Do not expose power tools to rain. Do
not use power tools in damp or wet locations. Keep work area well lit. Do
not use power tools where there is risk to cause fire or explosion.
3. Guard against electric shock. - Avoid body contact with earthed or
grounded surfaces (e.g. pipes, radiators, ranges, refrigerators).
4. Keep children away. - Do not let visitors touch the tool or extension cable.
All visitors should be kept away from area.
5. Store idle tools. - When not in use, tools should be stored in a dry, high or
locked up place, out of reach of children.
6. Do not force the tool. -It will do the job better and safer at the rate for
which it was intended.
7. Use the right tool. - Do not force small tools or attachments to do the job of
a heavy duty tool. Do not use tools for purposes for which it was not
intended.
8. Dress properly. -Do not wear loose clothing or jewellery, they can be
caught in moving parts. Rubber gloves and non-skid footwear are
recommended when working outdoors. Wear protecting hair covering to
contain long hair.
9. Use safety glasses. - Always wear suitable eye protection, manufactured
to the latest European Safety Standards, when firing the stapler/nailer.
Eyeglasses are not safety glasses
10. Do not abuse the cable. - Never carry the tool by the cable or yank it to
disconnect it from the socket. Keep the cable a way from heat, oil and
sharp edges.
11. Secure work. - Use clamps or a vice to hold the work. It is safer than using
your hand and it frees both hands to operate the tool.
12. Do not overreach. - Keep proper footing and balance at all times.
13. Maintain tool with care. - Inspect tool cable periodically and if damaged
have it repaired by an authorized service facility. Inspect extension cables
3
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
periodically and replace, if damaged. Keep handles dry, clean and free
from oil and grease.
14. Disconnect tools. - When not in use, before servicing and when changing
accessories such as blades, bits and cutters.
15. Avoid unintentional starting. - Do not carry a tool with a finger on the
switch.
16. Use outdoor extension leads. - When tool is used outdoors, use only
extension cables intended for outdoor use.
17. Stay alert. - Watch what you are doing. Use common sense. Do not
operate tool when you are tired.
18. Check damaged parts. - A guard or other part that is damaged should be
properly repaired or replaced by an authorized service centre unless
otherwise indicated in this instruction manual. Have defective switches
replaced by an authorised service facility. Do not use the tool if the switch
does not turn it on and off.
19. Warning. - The use of any accessory or attachment, other than those
recommended in this instruction manual, may present a risk of personal
injury.
20. Have your tool repaired by a qualified person. - This electric tool is complies
with the relevant safety requirements. Repairs should only be carried out by
qualified persons using original spare parts, otherwise this may result in
considerable danger to the user.
MACHINE SPECIFIC
1. Secure the workpiece. A workpiece held with clamping devices or in a
vice is held more secure than by hand.
2. Before any work on the machine itself (e.g. maintenance) as well as during
transport and storage, switch the machine off and remove the plug from
the power supply.
3. Keep your fingers away from the stapler/nailer head. There is danger of
injury when unintentionally actuating the On/ Off switch.
4. Never point the machine at persons or animals. Staples or nails shot from a
short distance can cause considerable injuries.
5. Do not use the machine to fasten electrical wiring. Contact with electric
wires can lead to fire and electric shock.
4
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
SAFETY SYMBOLS
Read manual before use
Wear suitable eye protection
SAFETY SYSTEM
FULL SEQUENTIAL ACTUATION
This stapler/nailer has an actuation system in which the trigger and safety yoke
are linked in such a way that it will only operate if the trigger is pulled after the
safety yoke (muzzle) has been applied to the work. Further driving operations
require the user to release the trigger and lift the safety yoke (muzzle) away from
the workpiece before the next use.
5
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
ELECTRICAL CONNECTIONS
WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS
THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS
SUPPLY.
Connect the mains lead to a standard, 230 Volt (50Hz) electrical supply
through an approved BS1363/A plug fitted with a BS1362 fuse.
If the plug has to be changed because of damage, it must be removed and a
replacement fitted, following the wiring instructions shown below. The old plug
must be discarded safely, as insertion into a power socket could cause an
electrical hazard.
WARNING: WIRES IN THE MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE: BLUE = NEUTRAL,
BROWN = LIVE.
• The BLUE wire must be
connected to the
terminal which is
marked N or coloured
black.
• The BROWN wire must
be connected to the
terminal which is
marked L or coloured
red.
Plug must be BS1363/A approved.
Always fit
a 5 Amp
fuse.
Neutral
(Blue)
Live
(Brown)
Ensure that the outer sheath of
the cable is firmly held by the clamp
We strongly recommend that this machine is connected to the mains supply
through a Residual Current Device (RCD)
If you are not sure, consult a qualified electrician. DO NOT try to do any
repairs.
6
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
PREPARING THE STAPLER/NAILER FOR USE
FILLING THE MAGAZINE
WARNING: SWITCH OFF THE STAPLER/NAILER AND REMOVE THE PLUG
FROM THE MAINS POWER SUPPLY BEFORE FILLING THE MAGAZINE.
CAUTION: KEEP YOUR FINGERS WELL AWAY FROM THE TRIGGER,
1. Press and hold the magazine
catch (1) then pull out the
magazine (2).
2. Turn over the stapler/nailer and
insert the staple strip or the nail
strip.
• Hold the stapler/nailer at a
slight angle while inserting the
nail strip so that nails rest
against the side wall.
• Nails should be placed against
the side of the chamber which
has a dip in it (Left side when
the tool is inverted and the yoke is furthest away from the user).
• Only those fasteners stated in the specification should be used.
3. Close the magazine.
• Make sure it clicks shut.
7
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
USING THE STAPLER/NAILER
1. Pay attention to all of the safety warnings in these operating instructions.
2. Set the ON/OFF switch to the ON
position.
3. Press the stapler/nailer against the
work and pull the trigger.
• Always hold the stapler/nailer
square to the workpiece, never
at an angle.
4. Release the trigger and lift the
stapler/nailer away from the
workpiece.
5. Repeat steps 3-4 as required.
6. In the event of long breaks in work or at the end of the working shift:• Switch off the stapler/nailer,
• Remove the mains plug from the power supply,
• Empty the magazine.
TIPS
• Do not intentionally activate the stapler/nailer if the magazine is
empty.
• Do not attempt to staple/nail at the edge of a workpiece, the edge
could fail, causing a nail or staple to shoot straight through.
TO CLEAR A JAM
Do not pull the trigger until the jam has been cleared, as this could cause
serious damage:
WARNING: SWITCH OFF THE STAPLER/NAILER AND REMOVE THE PLUG
FROM THE MAINS SUPPLY BEFORE CLEARING A JAM.
1. Release the magazine catch and slide the magazine open.
2. Remove all staples/nails from the chamber.
3. Using pliers, grip the jammed fastener and pull firmly to dislodge it.
4. Once the jammed fastener is removed, reload and continue.
8
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
MAINTENANCE
WARNING: SWITCH OFF THE STAPLER/NAILER AND REMOVE THE PLUG
FROM THE MAINS POWER SUPPLY BEFORE CARRYING OUT ANY
SERVICING OR MAINTENANCE
• The stapler/nailer does not require any specific maintenance other
then keeping it free from any dirt or debris. This can be done using a
clean dry cloth and/or brush. Do not use solvent or alcohol based
cleaner as it could damage the casing.
• There are no user serviceable parts on the stapler/nailer. If there is a
problem please contact your nearest CLARKE dealer.
• Do not open the casing, the guarantee will be void if the casing has
been opened or if the stapler/nailer has been tampered with.
• The use of parts other than CLARKE replacement parts may result in
safely hazards, decreased tool performance and will invalidate your
warranty.
9
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
SPECIFICATION
Input Voltage
230V, 50Hz, 1Ph
Max Firing Speed
20 shots/min.
Maximum Magazine Capacity
100 Nails or 100 Staples
Nail Type
18 gauge/ 15mm Brad Nail
Staple Type
22 gauge (Type 53) - 6mm, 8mm, 10mm
Dimensions
280 x 170 x 65 mm
Weight
1.28 kg
Activation Mode
Full Sequential Actuation
Noise Characteristic Values In Accordance With EN12549.
Sound Pressure:
73.3 dB(A)
Sound Power Measured LwA
86.3dBLwA
Vibration Characteristic Values In
Accordance With ISO 8662-1 1:
1999
2.971 m/s2
10
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
DECLARATION OF CONFORMITY
11
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com