XRSuper6
User’s Guide
Silencing an Alarm
All/Perimeter and Home/Away Systems
1. While the alarm bell or siren is sounding, enter your user code. The keypad displays DISARM
SILENCE.
2. Press the Select key under SILENCE to stop the bell or siren. This does NOT disarm the system.
3. If your system is programmed to send an Abort (alarm cancel) report to the central station, the keypad displays ALARM CANCELLED
the next time the panel is disarmed, if it is disarmed before the bell cutoff time expires.
Copyright © 2002 Digital Monitoring Products, Inc.
Information furnished by DMP is believed to be accurate and reliable.
This information is subject to change without notice.
The XRSuper6 panel is UL listed for Grade A Household Service and Commercial Burglary Service
Security Command® User's Guide
XRSuper6 Command Processor™ Panels
Table of Contents
Section
Page
About Your Security System ........................................ 1
Understanding Security System Terms .......................... 2
The LCD Security Command Keypad ............................. 4
Special Security Command Messages ........................... 5
Special Security Command Tones ................................ 5
How your System Operates ......................................... 6
All/Perimeter System Arming ...................................... 7
All/Perimeter System Disarming .................................. 8
Home/Away System Arming ........................................ 9
Home/Away System Disarming .................................. 10
User Check-in .......................................................... 12
Zone Activity Check .................................................. 12
Sensor Reset .......................................................... 13
Outputs On Off ....................................................... 13
Bypass Zones .......................................................... 14
Zone Monitor ........................................................... 14
System Test ............................................................ 15
User Codes ............................................................. 16
Ambush Codes ........................................................ 17
Date and Time ......................................................... 18
Display Events ......................................................... 19
Zone Activity Check Event Display ............................... 19
Zone Bypass Event Displays ....................................... 20
Section
Page
Zone Event Displays ................................................. 20
Arming and Disarming Event Displays ......................... 21
User Check-in Event Displays ..................................... 21
User Code Change Event Displays .............................. 21
Supervisory Event Displays ........................................ 21
System Monitor Event Displays .................................. 22
Service Request? ..................................................... 22
The LED Security Command Keypad ........................... 23
Built-in Alert Operation ............................................. 24
Arming and Disarming with the LED Keypad ................ 25
LED Security Command Keypad Functions ................... 26
System Setup .......................................................... 28
Protection Areas ...................................................... 28
Outputs .................................................................. 28
User Codes ............................................................. 29
Easy Entry™ User's Guide .......................................... 30
FA113 User's Guide .................................................. 32
Pager Direct™ User's Guide ....................................... 33
PhoneAccess™ User's Guide ...................................... 35
895 Voice Module ..................................................... 36
Common Keypad Displays ......................................... 37
Index ...................................................................... 38
i
This page intentionally left blank.
Introduction
About Your Security System
A Note About False Alarms
Your Security Command system has been designed with your safety
and comfort in mind. It uses the latest in computer technology
to create the most user friendly security and fire system on the
market today.
One of the most important concerns facing the security industry
today is false alarms. The accidental dispatching of police and
fire agencies places others in jeopardy by limiting the response
capability of those emergency service units.
The system combines ease of use with a simple to understand
Security Command keypad display to offer the full range of features
requested by today’s security system owners. Security Command
can protect both the interior and perimeter of your home or
business while you are away or just the perimeter when you are
inside giving you a wall of security and peace of mind.
As part of our commitment to reducing false alarms, we would
like to encourage you to read this guide thoroughly. All the
information contained here can help you quickly, and comfortably,
learn the operation of the Security Command system. If you
have any additional questions, or feel that you need more training,
please do not hesitate to contact us.
You can turn portions of your protection on or off at any time by
pressing a few buttons. You can add, delete, and change personal
user codes at any time or check the status of all protection
devices in the system.
Test Your System Weekly
Security Command® keypad
This is the device we have placed at certain locations throughout
the premises that allow you to turn the system’s protection on
and off using your personal user code number.
It is recommended that you test the burglary portion of your
system at least once each week. Testing should involve an active
test of all doors, windows, and motion detectors connected to
your system. If your system also has fire protection, call the
service department to find out how this portion of your system
should be tested.
Refer to the System Test section of this guide for instructions on
testing the burglary portion of your system.
Keypad User Menu
The keypad also provides a User Menu containing all of the
functions you need to fully operate your system, such as the
ability to change a personal user code number.
XRSuper6 Introduction
1
Understanding Security System Terms
Throughout this guide and in some displays on your keypad, you
will see certain words or phrases that might be unfamiliar. Although
every effort has been made to use terms that are commonly
known, there are some for which there is no acceptable
substitute. Some common terms are discussed below.
Entry or Exit Zone
Arming
When you arm the system, activity on all burglary zones is ignored
until the programmed exit delay time expires. Once that time
has expired and the system is fully armed, opening the door
causes the panel to start the entry delay time. During the entry
delay time, you must enter a valid user code to disarm the system
or an alarm will occur.
This is the term used for turning on the burglary protection in
one or more areas of the system. Your system may require you
to enter a user code. When armed, the system is able to sound
alarm bells or sirens and, if monitored, send alarm reports to a
central station when a burglary zone is faulted.
Fire, panic, and other 24-hour devices are always turned on and
do not need to be armed.
Disarming
This means turning off one or more areas of the system. When
disarmed, the system does NOT sound alarms or send alarm reports
to a central station when a burglary zone is faulted.
Zone
A zone refers to a group of one or more protected openings or
protection devices assigned the same zone number. Each door
or window, motion detector, smoke detector, or other device
has a zone number and a name.
Often, similar devices in the same general area will share the
same zone. For example, the windows on the east side of the
premises can all be grouped together in a zone named E.
WINDOWS.
2
Almost all systems have one or more doors through which you
can enter or exit the premises. These doors are programmed
with a delay time to allow you to enter or exit while the system
is armed without setting off the alarm.
Instant Zone
Exterior windows and non-entry doors, or interior protection
devices, are typically not programmed with delay times. If these
zones are faulted while the system is armed, an alarm occurs
instantly.
24-Hour Zone
A 24-hour zone is never assigned to an area and is not turned on
or off by arming or disarming your system. Some examples of 24hour zones are fire zones, panic zones, and temperature control
zones.
Areas
An area is made up of burglary zones that can be armed or
disarmed together. The Perimeter area, for example, consists of
all the doors and windows on the outside of the building. When
you arm the Perimeter, these zones sound an alarm if tripped.
XRSuper6 Introduction
Central Station Monitoring
Armed Status
Your system can also be programmed to automatically send alarm,
trouble, and arming and disarming reports to a central station.
Operators at the central station can then dispatch the
appropriate authorities or contact you with event information.
With Armed Status, the keypad displays the current armed
condition of areas within your security system.
Status
There are two types of status information available: Status List
and Armed Status.
Status List
The keypad Status List displays any alarm or trouble conditions
on a zone and any trouble condition that occurs with the AC
power or battery power. If your system contains any Panic zones,
these are not displayed on the keypad for security reasons.
If an alarm occurs on a non-fire, 24-hour zone or a system monitor,
it remains in the Status List until it restores. If one or more
armed burglary zones trips, the last one to trip remains in the
Status List. The burglary zone alarm remains in the Status List for
several minutes or until it is cleared by disarming the system.
Zone Status
To display the status of a particular zone, enter the zone number
followed by the COMMAND key when the keypad is displaying the
Status List.
The keypad displays
When
HOME MODE ON
The perimeter area is on in a Home/
Away system
PERIMETER ON
The perimeter is armed in an All/
Perimeter system
ALL SYSTEM ON
All areas are on
SLEEP MODE ON
The perimeter and interior areas are
on but the bedroom area is off
Also, for keypads that include an Armed LED, the Armed LED is ON
steady anytime a burglary protection area is armed and OFF when
ALL areas are disarmed.
Exit Error
An automatic function of the panel that prevents an alarm from
occurring if an exit door does not close all the way after the
system has been armed. For example, if the front door is left
ajar upon exit and the exit delay time has expired, the system
attempts to arm the front door zone but recognizes the open
condition and, instead of sending an alarm report to the central
station, sends an Exit Error report and force arms the door. (If
the door closes at a later time it will be included back into the
system.) The system sounds the alarm sirens for 15 seconds to
alert you of the condition and provide an opportunity for you to
close the door.
The Exit Error feature allows the central station to acknowledge
the arming error without dispatching the police on a false alarm.
XRSuper6 Introduction
3
The Security Command Keypad
Your system may have one or more easy-to-use Security Command
keypads (16 or 32-character) that allow you to properly operate
the system. The illustrations and descriptions below highlight
some of the keypad features:
32-Character Keypad
AC
LED
ARMED
LED
POWER
Lighted display
JONES RESIDENCE
F R I 2 : 51 AM
ARMED
1
2
AB C
5
3
DEF
6
MN O
9
4
GHI
PQR
0
JKL
8
7
S TU
3
2
6
MNO
9
4
GHI
DEF
ABC
5
0
YZ
STU
POWER
JKL
VWX
COMMAND
This LED remains on steady as long as your system is connected
to its AC power supply. Should there be an interruption, the LED
turns off and the system's backup battery maintains normal
operation to allow you to contact our service department.
Lighted display
ARMED LED
Select keys
AC LED
This LED is ON steady anytime burglary protection is armed and
OFF when ALL areas are disarmed.
Data Entry keys
32-Character Keypad User Options Menu
COMMAND key
Press and hold the Back Arrow and COMMAND keys for about two
seconds. The keypad display shows SET BRIGHTNESS. Use the
left Select key to lower the display brightness and the right
Select key to increase brightness. Press COMMAND.
Back Arrow key
The Select keys
The four keys under the display, the Select keys, make your
system so easy to operate. They allow you to choose what to do
by pressing the Select key under choices being shown in the
display.
4
The COMMAND key
AC LED
8
7
PQR
You can press the Back Arrow key to back up through the list of
functions in the User Menu or to make a correction by erasing
the last character you entered.
Data Entry keys
Back Arrow key
1
The Back Arrow key
Select keys
YZ
16-Character Keypad
These keys allow you to enter your user code when arming or
disarming and enter other information into the system.
The COMMAND key allows you to advance through the keypad
displays or User Menu or complete a data entry function.
COMMAND key
VWX
COMMAND
Data Entry keys
At SET TONE, use the left Select key to lower the keypad tone
and the right Select key to raise the tone. Press COMMAND.
At SET VOLUME LEVEL, use the left Select key to lower the
keypad volume and the right Select key to raise the volume.
Press the Back Arrow key to exit the User Options menu.
XRSuper6 Introduction
Special Security Command Messages
Special Security Command Tones
Below are a few examples of the displays you will see on your
keypad.
Your keypad also contains a small speaker that allows it to alert
you to events as they occur on your system. Below are brief
descriptions of the different tones you will hear from the keypad:
ALARM
A 24-hour zone, such as a fire or panic zone, or an armed burglary
zone has been faulted. Your system may sound bells or sirens.
ALARM CANCELLED
Fire alert: Your keypad may sound a fire tone to alert persons in
the vicinity to the alarm condition. This is in addition to the bell
output from the alarm panel.
This message displays when an authorized user cancels an alarm
condition by entering a valid user code and an “Alarm Cancelled”
report was sent to the central station.
Burglary alert: Your keypad may sound a burglary tone to alert
persons in the vicinity to the alarm condition. This is in addition
to the bell output from the alarm panel.
TROUBLE
Key press tone: A short beep as you press a key on the keypad.
There is a problem with a protection device or component. This
display is accompanied by a description of the problem.
Prewarn tone: A continuous pulsed tone that sounds when you
open an entry delay door on a system that is armed (turned on)
reminding you to disarm the burglary protection.
ENTERCODE
The system requires you to enter a personal user code. User
codes can be required for turning your system on (arming), turning
your system off (disarming), and other system options. As you
enter your user code, the keypad display shows an asterisk (*) in
place of each digit pressed.
TRY AGAIN
The system does not recognize the user code that was entered.
Check the user code and try again.
INVALID CODE
The system does not recognize the user code you entered.
SYSTEM TROUBLE or SERVICE REQUIRED
There is an electronic failure in your system. Contact the service
department as soon as possible.
XRSuper6 Introduction
Monitor tone: A short tone that sounds for one second whenever
a door or window is opened while you are using the zone monitor
function from the User Menu. See Zone Monitor.
Trouble tone: A steady tone indicating a trouble condition on
your system. Press a Select key to silence the trouble tone.
Zone Activity Check tone: A steady tone indicating no zone activity
has occurred on your system within the programmed period of
time. Press any key to silence the tone.
What to do when the trouble tone is sounding
You can silence the trouble tone by pressing any one
of the top row Select keys. This only silences the
keypad and does not correct the condition that
originally caused the problem.
5
How your System Operates
Your system has been programmed to operate in one of two
modes: All/Perimeter, or Home/Sleep/Away.
• All/Perimeter - Your burglary protection is divided into two
areas: Interior and Perimeter. You can turn on the just the
Perimeter protection while inside for security or turn on both as
you leave.
• Home/Sleep/Away - Your burglary protection is divided into
three areas: Interior, Perimeter, and Bedrooms. You can turn on
the Perimeter, Perimeter and Interior, or all three areas separately.
Regardless of which mode has been programmed, much of the
operation is similar. Throughout this guide, any differences
between the systems are noted for your convenience.
Arming Functions
After making your arming selection, the keypad displays any zones
that are currently bypassed. These zones remain bypassed until
the system is armed and then disarmed. Any 24-hour zones in a
faulted condition are also displayed.
During arming, the system verifies that all doors, windows, and
other protection devices to be armed are in normal condition.
If everything is alright (normal), the system arms. If there is a
problem on one or more burglary zones the keypad displays the
problem and allows you to bypass those zones.
If the problem can be corrected by closing a door or window, do
not bypass the zone. Instead, correct the problem and try arming
again. If the problem cannot be corrected, you can bypass the
zone or wait until the zone can be repaired by a service
technician. A bypassed zone is ignored by the system during the
armed period.
In some cases the keypad might display FRONT DOOR - FAULT.
The keypad may then display PRIORITY ZONE, which is a zone
that cannot be bypassed. The problem on the zone must be
corrected before the system can be armed.
Armed Message: After all bypassing is completed or zone faults
corrected, the areas you selected are armed. The keypad briefly
displays ALL SYSTEM ON if all areas in the system are arming and
HOME MODE ON or SLEEP MODE ON if only selected areas are
arming. The keypad then displays the exit delay as it counts
down. Zones are not armed until the exit delay time expires.
If your system uses a keyswitch to arm an area, the exit delay
time is NOT shown on the keypad display.
DIALING . . . Message: If your system is monitored, it may be
programmed to wait for the arming report to be sent to the
central station before displaying the armed message. (See Arming
Report below.) This is to verify your phone lines are working
properly. While the system is waiting, the display reads DIALING....
If the report is received, the keypad buzzes for one second and
displays the armed message. If the report is not received, the
keypad displays LOCAL ALARM ONLY before displaying the armed
message.
Arming Report: Your system can be programmed to send arming
or zone bypass reports to a central station. This feature is
optional and can be programmed for you at any time.
6
XRSuper6 Introduction
Arming and Disarming
All/Perimeter System Arming
Area Assignment: Your security system is divided into two separate
areas. Motion detectors, inside doors, and other interior
protection devices are assigned to the Interior area while windows
and exterior doors are assigned to the Perimeter area.
Perimeter or All: When arming an All/Perimeter system, the keypad
displays PERIM
ALL. If you select ALL, you arm both the
Perimeter and the Interior of the system. You will want to arm
both of these areas when leaving with nobody left inside.
Selecting PERIM arms only the Perimeter of the system. Perimeter
arming is for when you are staying inside but want the comfort of
knowing the exterior doors and windows are armed.
System Ready/System Not Ready Keypad
Displays
When all zones in the system are in a normal condition, the keypad
displays SYSTEM READY. If there are one or more zones that are
not in a normal condition, the keypad displays SYSTEM NOT READY.
Pressing any top row Select key during this display shows the
zone name allowing you to investigate the problem.
Instant Arming
Instant: During the exit delay time, you can cancel the exit and
entry delays and cause all zones to be instant zones. Press the
far right select key under INSTNT while the exit delay is displayed.
This immediately arms the exit zones. However, no entry delay is
provided and an alarm will occur should an entry door be opened.
XRSuper6 Arming and Disarming
Arming an All/Perimeter System
1. Enter your code. The keypad displays PERIM
ALL.
2. Select PERIM to arm the Perimeter area only or select ALL to
arm both the Perimeter and Interior areas.
The keypad displays any bypassed zones and 24-hour zones
that are in a bad condition. No action is required by you.
3. At this point you can force arm or bypass any bad zones. A
zone that is force armed will be restored into the system if it
later returns to normal. A zone that is bypassed will remain
bypassed until the system is disarmed. See below.
3a. If a problem exists on any zones, the zone name and
problem are shown followed by: OKAY BYPASS STOP.
3b. Select OKAY to force arm the zone(s) before arming.
3c. Select BYPASS to bypass the zone(s) before arming.
3d. Select STOP to stop the system from arming. Correct the
zone problem(s) and return to step 1.
The keypad displays PERIMETER ON if only the perimeter is
being armed and ALL SYSTEM ON if both the perimeter and
interior are being armed.
The keypad next displays EXIT: ## INSTNT and begins to count
down the number of seconds remaining for you to exit. When
the delay expires, all zones are armed.
4. You can select INSTNT while EXIT: ## INSTNT is displayed to
immediately arm all zones and make them instant. The keypad
displays INSTANT.
5. When the system is fully armed, the keypad displays PERIMETER
ON for perimeter arming and ALL SYSTEM ON for perimeter
and interior arming.
7
All/Perimeter System Disarming
Disarming: While the system is armed, you can only enter the
premises through an entry/exit delay door without causing an
alarm. After opening the door, the Security Command keypad
sounds a prewarn tone to remind you to disarm the system. You
must disarm the system before the prewarn tone expires or an
alarm on the door zone will occur.
During the prewarn tone, the keypad displays ENTER CODE:. Enter
your user code to disarm the system.
Alarm Display: After disarming, the keypad displays any zones
that tripped or any transmission problems that occurred during
the armed period. All burglary zones are then disarmed and any
bypassed zones are automatically reset.
Disarmed Message: The keypad displays ALL SYSTEM OFF after
the system disarms.
Central Station Report: A report of the system disarming can be
transmitted to the central station. This is optional and can be
programmed for you at any time.
Disarming an All/Perimeter System
Disarming During an Alarm
1. While the alarm bell or siren is sounding, enter your user
code. The keypad displays DISARM SILENCE.
2. Press the Select key under DISARM to disarm the system and
silence the alarm.
The keypad next displays ALL SYSTEM OFF to confirm the
system is disarmed.
3. Press the Select key under SILENCE to stop the bell or siren
but NOT disarm the system.
If you do not press any Select key, or you press the COMMAND
key, the system will automatically disarm and silence the alarm.
4. If your system is programmed to send an Abort (alarm cancel)
report to the central station, the keypad displays ALARM
CANCELLED.
Note: If your system is programmed to send an Abort (alarm cancel)
report to the central station, selecting DISARM will send this
report to the central station. Be sure that you want the alarm
message to be cancelled BEFORE deciding to disarm the system.
If you do not want to disarm the system and send the abort
report, press SILENCE to only turn off the alarm bells.
1. During the entry delay time, the keypad displays ENTER
CODE:. Enter your user code.
2. The keypad then displays any zones that went into alarm or any
communication problems that occurred during the armed
period.
3. The keypad next displays ALL SYSTEM OFF to confirm the
system is disarmed.
8
XRSuper6 Arming and Disarming
Home/Away System Arming
Area Assignment: Your security system is divided into two or
three separate areas. Motion detectors, inside doors, and other
interior devices are assigned to an Interior and possibly Bedroom
area while windows and exterior doors, are assigned to a Perimeter
area.
Arming the system: When arming a Home/Away system, the keypad
displays HOME
AWAY or HOME SLEEP AWAY. If you select
AWAY, you arm all areas of the system. You will want to arm all
areas when leaving with nobody staying inside. Selecting HOME
arms only the Perimeter of the system. Perimeter arming is for
when you are staying inside but want the comfort of knowing
the exterior doors and windows are armed. Selecting SLEEP
arms the Perimeter and Interior devices but leaves devices near
bedrooms and other nighttime areas off.
System Ready/System Not Ready Keypad
Displays
When all zones in the system are in a normal condition and can
be armed without bypassing, the keypad displays SYSTEM READY.
If there are one or more zones that are not in a normal condition,
the keypad displays SYSTEM NOT READY. Pressing any top row
Select key during this display shows the bad zone name.
Arming a Home/Away System
1. Enter your user code. The keypad displays HOME
AWAY
or HOME SLEEP AWAY (you may have three areas).
2. Select HOME to arm the Perimeter only. Select SLEEP to arm
the Perimeter and Interior. Select AWAY to arm the
Perimeter, Interior, and Bedroom.
XRSuper6 Arming and Disarming
The keypad displays zones that have been bypassed prior to
arming and 24-hour zones that are in a bad condition. No
action is required by you.
3. At this point you can force arm or bypass any bad zones. A
zone that is force armed will be restored into the system if it
later returns to normal. A zone that is bypassed will remain
bypassed until the system is disarmed. See below.
3a. If a problem exists on any zones, the zone name and
problem are shown followed by: OKAY BYPASS STOP.
3b. Select OKAY to force arm the zone(s) before arming.
3c. Select BYPASS to bypass the zone(s) before arming.
3d. Select STOP to stop the system from arming. Correct the
zone problem(s) and return to step 1.
The keypad displays PERIMETER ON if you selected HOME, or
PERIM/INT ON if you selected SLEEP, or ALL SYSTEM ON if you
selected AWAY.
The keypad next displays EXIT: ## INSTNT and begins to count
down the number of seconds remaining for you to exit. When
the delay expires, all zones are armed.
4. You can select INSTNT while EXIT: ## INSTNT is displayed to
immediately arm all zones and make them instant. The keypad
displays INSTANT.
5. When the system is fully armed, the keypad displays PERIMETER
ON for Perimeter arming, PERIM/INT ON for Perimeter and
Interior arming, and ALL SYSTEM ON for all areas armed.
9
Home/Away System Disarming
Disarming: While the system is armed, you can only enter the
premises through an entry/exit delay door without causing an
alarm. After opening the door, the keypad sounds a prewarn
tone to remind you to disarm the system. You must disarm the
system before the prewarn tone expires or an alarm on the door
zone will occur.
During the prewarn tone, the keypad displays ENTER CODE:. Enter
your code to disarm the system.
Alarm Display: After disarming, the keypad displays any zones
that tripped or any communication problems that occurred during
the armed period. All burglary zones are then disarmed and any
bypassed zones are automatically reset.
Disarmed Message: The keypad displays ALL SYSTEM OFF after
the system disarms.
Central Station Report: A report of the system disarming can be
transmitted to the central station. This is optional and can be
programmed for you at any time.
Easy Exit™ Feature
While the system is armed, you can also just press the COMMAND
and then the 9 key to restart the exit delays to allow you to exit
the premises without disarming the system. After the exit delay
time expires, the system re-arms automatically. This feature allows
you to get the paper, let your pet out, or leave for work without
having to disarm and then rearm the system.
10
Disarming a Home/Away System
1. During the entry delay, the keypad displays ENTER CODE:.
Enter your 4-digit user code.
2. The keypad then displays any alarms or communication
problems that occurred during the armed period.
3. The keypad next displays ALL SYSTEM OFF to confirm the
system is disarmed.
Disarming During an Alarm
1. While the alarm bell or siren is sounding, enter your 4-digit
user code. The keypad displays DISARM
SILENCE.
2. Press the Select key under DISARM to disarm the system and
silence the alarm.
The keypad next displays ALL SYSTEM OFF to confirm the
system is disarmed.
3. Press the Select key under SILENCE to stop the bell or siren
but NOT disarm the system.
If you do not press any Select key, or you press the COMMAND
key, the system will automatically disarm and silence the
alarm.
4. If your system is programmed to send an Abort (alarm cancel)
report to the central station, the keypad displays ALARM
CANCELLED.
Note: If your system is programmed to send an Abort (alarm cancel)
report to the central station, selecting DISARM will send this
report to the central station. Be sure that you want the alarm
message to be cancelled BEFORE deciding to disarm the system.
If you do not want to disarm the system and send the abort
report, press SILENCE to only turn off the alarm bells.
XRSuper6 Arming and Disarming
Security Command User Menu
Many of the features of your system have been put into a User
Menu you can access from any Security Command keypad.
BYPASS ZONES
Bypass or reset a zone.
ZONE MONITOR
Add or remove a zone from the
monitor mode.
SYSTEM TEST
Tests the system's siren,
communication to the central
station, and backup battery.
USER CODES
Add, delete, or change user
codes and authority levels.
DATE AND TIME
Change the system’s Day, Date,
or Time.
Accessing the User Menu
1. Press the COMMAND key until MENU? NO YES displays.
2. Select YES. The keypad displays ENTER CODE: –. Enter your
user code. You can now scroll down through the list of
system features available to your authority level.
User Menu Options
The list below shows the User Menu options in order:
Menu Option
Description
USER CHECKIN
Check-in with the system to
indicate arrival on premise.
DISPLAY EVENTS
View or print the last 200 events
that occurred on your system.
ZONE ACTIVITY CHECK
Check the activity on each zone.
SERVICE REQUEST
SENSOR RESET
Reset smoke or glassbreak
detectors that have latched
during an alarm.
Send a message to the central
station requesting service on the
alarm system.
OUTPUTS ON/OFF
XRSuper6 User Menu
Turn on or off any of the outputs
described in the System Setup
section of this guide.
The following pages detail each User Menu item and provide
instructions on when and how to use them properly.
11
User Check-in
Zone Activity Check
User Code Level: Master or Standard
User Code Level: Master or Standard
Function: This feature allows you to monitor the arrival of latchkey
children or employees by having a special Check-in Report sent
to your numeric pager. Your system must be programmed for the
Pager Direct™ option. The Appendix section of this guide contains
Quick Reference cards for your wallet or purse.
Function: This option allows you to monitor your system for zone
activity. When the programmed time period is exceeded because
no activity is detected, your keypads will sound a steady tone
and display PRESS ANY KEY. When this tone sounds, you can
silence the tone and prevent the panel from sending a “User
Activity Not Detected” report to the central station by pressing
any key before the countdown timer on the keypad display reaches
zero. This restarts the zone activity check time period.
Sending a Check-in Report:
1. After disarming the system, access the User Menu.
(Or press the COMMAND then 7 key and enter your user code
to send a Check-in Report. This feature operates on 32character keypads only.)
2. At the USER CHECKIN? display, press any Select key. The
keypad displays USER CHECKIN: 22 ( 22 = user number).
3. The panel sends the Check-in Report containing your account
number and user number to the pager.
12
This could be used for a person living alone to detect when they
have not tripped a disarmed zone within a programmed period of
time. This feature can be programmed for you at any time.
Selecting Zone Activity Check:
1. At the ACTIVITY CHECK? display, press any Select key. The
keypad displays ENABLE? YES NO. The default is YES.
2. When NO is selected, the keypad displays CHECK DISABLED
for four seconds and then sends the Activity Check Disabled
message to the central station.
3. When YES is selected, the keypad displays CHECK ENABLED
for four seconds and then sends the Activity Check Enabled
message to the central station.
XRSuper6 User Menu
Sensor Reset
Outputs On Off
User Code Level: Master or Standard
User Code Level: Master or Standard.
Function: Resets smoke or glassbreak detectors. Also clears Fire
and Supervisory zone alarms and trouble keypad displays. Sensor
Reset also clears low battery displays if your system is using
wireless sensors.
Function: Allows you to turn the system's outputs on and off.
Once smoke or glassbreak detectors have tripped, they must be
reset before they can detect any additional alarm conditions.
When Sensor Reset is selected, power to the detectors is
temporarily removed by the system allowing them to reset.
Make sure all smoke is cleared from around the area of the smoke
detectors before performing a Sensor Reset to prevent the alarm
from occurring again.
Resetting the Sensors
1. Access the User Menu.
2. When SENSOR RESET? is displayed, press any Select key. The
keypad displays SENSORS OFF for five seconds followed by
SENSORS ON.
3. The keypad returns to the status display.
Enter your user code to reset sensors
While your system is disarmed, you can just enter your user
code and press COMMAND to reset the sensors.
This also activates the door strike if your system has an Easy
Entry™ access control keypad.
XRSuper6 User Menu
This function is used to individually turn your system’s relay
outputs on and off. Your system may use these outputs to control
interior and exterior lighting, or heating, air conditioning, or
other appliances.
The names and numbers of the outputs on your system are located
in the System Setup section at the back of this guide.
Turning the Outputs On and Off
1.
2.
3.
4.
5.
Access the User Menu.
Press the COMMAND key until OUTPUTS ON/OFF? displays.
Press any one of the Select keys.
The keypad displays OUTPUT: - ON OFF.
Enter the output number you want to turn on or off. The
output number appears in the display.
6. With the output number displayed, press the Select key
under ON or OFF. The output is then turned on or off,
depending on your selection, and remains in that state until
you change it.
7. The system automatically removes the output number and a
new output number can be entered. Refer back to step 5.
To exit the Output menu option, press the Back Arrow key until
you have returned to the keypad's Status List.
13
Bypass Zones
Zone Monitor
User Code Level: Master or Standard.
User Code Level: Master and Standard.
Function: Allows you to bypass a zone prior to arming the system.
Function: Allows the system to monitor selected disarmed zones
(doors, windows, or motion detectors). When a monitored zone
is tripped, the keypad sounds a tone and displays the zone name.
This is an ideal feature for monitoring doors to tell when someone
comes in or goes out and for testing the system.
Bypassing is usually done when a zone cannot be restored to
normal and you want to arm the system. Once bypassed, the
system will not respond to any activity on the zone.
A zone can be bypassed only while it is disarmed. Since Fire,
Panic, Emergency, and Supervisory zones are always armed, they
can never be bypassed.
The Bypass Zones function can also be used to restore a bypassed
zone back into the system. This can only be done while the zone
is disarmed.
When Bypass Zones is selected, a report of the bypassing can be
sent to your central station. This is optional and can be
programmed for you at any time.
Using the Bypass Zones Function
1. Access the User Menu.
2. Press the COMMAND key until BYPASS ZONES? displays.
3. Press any one of the Select keys. The keypad displays ZONE:
- RST BYPS.
4. To reset a zone, enter the zone number and press the Select
key under RST.
5. To Bypass a zone, enter the zone number and press the Select
key under BYPS.
14
You can place any combination of disarmed zones in Zone Monitor
but only the most recently tripped zone is displayed. The displayed
zone name clears automatically after a short time or when the
zone is armed.
Using Zone Monitor as part of your weekly system test: After
using the System Test function, place all perimeter and interior
zones in Zone Monitor. Starting at the front door, open and then
close each door in the premises. You should hear the keypad
beep each time. The keypad will also display the name of each
zone as the device is opened.
Once all protected doors and windows have been tested, walk in
front of each motion detector, open and close each window,
and trip any other protection devices on the system. If at any
time during your weekly testing a device does not cause the
keypad to beep, call the service department for assistance.
XRSuper6 User Menu
Using the Zone Monitor Function
1. Access the User Menu.
2. Press the COMMAND key until ZONE MONITOR? displays.
3. Press any one of the Select keys.
The keypad displays PERIM ALL NBR .
4. Select PERIM to monitor all disarmed perimeter zones.
4a. The keypad displays PERIM? ADD RMV.
4b. Select ADD to add all perimeter zones to Zone Monitor.
4c. Select RMV to remove all perimeter zones.
5. Select ALL to place all disarmed perimeter and interior zones
into Zone Monitor.
5a. The keypad displays ALL? ADD RMV.
5b. Select ADD to add all disarmed zones to Zone Monitor.
5c. Select RMV to remove all disarmed zones.
6. Select NBR to enter a specific zone number for zone monitor.
6a. If NBR is selected, the keypad displays ZONE : - ADD RMV.
6a. Enter any zone number and select ADD to add this zone.
6b. Enter any zone number and select RMV to remove the
zone.
The zone number automatically disappears and a new zone
number can then be entered.
XRSuper6 User Menu
System Test
User Code Level: Master or Standard.
Function: System Test is used to test the battery, alarm bell or
siren, and communication to a central station. The System Test
function begins automatically as soon as you select it.
Using the System Test Function
1. Access the User Menu.
2. Press the COMMAND key until SYSTEM TEST? displays.
3. Press any one of the Select keys. The system test begins
automatically and the keypad displays:
1) BELL SOUNDING during a two second bell test
2) BATTERY - OKAY or BATTERY - TRBL to indicate the
condition of the battery
3) TRANSMIT TEST and ATTEMPT NO : 1 during the
transmit test. The transmit test does not operate on
local systems.
4) TRANSMIT OKAY or TRANSMIT FAILED to show the
results of the transmit test
5) TEST END to indicate the System Test is complete.
6) End the transmit test by pressing the Back Arrow key.
Testing your system's burglary protection: The System Test
function should be part of your weekly testing and should be
followed by placing the interior and perimeter burglary devices
in Zone Monitor mode. See Zone Monitor.
15
User Codes
User Code Authority Levels
User Code Level: Master only.
Function: Allows you to add or delete a user from the system or
change their user code or authority level.
There are three characteristics associated with each user code:
10
User number
3812
User Code
Master
Authority level
User Number - Your system supports 16 users. Each user is
numbered from 1 to 16. This number identifies them to the
system and is transmitted to the central station (if your system is
monitored) when they arm or disarm the system.
User Code - Users also have a 4-digit user code they enter into
the keypad when arming or disarming. This user code is kept
secret from other users and is not transmitted to the central
station when they arm or disarm.
Authority Level - The user is also assigned a level of authority
(Master or Standard) by the person administrating the system
that determines the functions they can access.
The table to the right lists system functions users are allowed to
access based on the authority level assigned to their codes at
the time they are added to the system.
16
System Options
Sensor Reset
Outputs On/Off
Bypass Zones
Zone Monitor
System Test
Arm and Disarm
Display Events
Date and Time
User Codes
Standard
✔
✔
✔
✔
✔
✔
✔
Master
✔
✔
✔
✔
✔
✔
✔
✔
✔
Adding User Codes
1.
2.
3.
4.
Access the User Menu.
Press the COMMAND key until USER CODES? displays.
Press any Select key. The keypad displays ADD DEL CHG.
Press the Select key under ADD to add a new user code.
(You must have a Master user level to add a user to the
system.)
5. At the USER NUMBER:
- prompt, enter a user number and
press COMMAND. The displays changes to CODE NO:
.
6. Enter a 4-digit user code and press COMMAND. This is the
number the user will use each time they arm, disarm, or make
changes to the system.
XRSuper6 User Menu
7. The display changes to MASTER? NO YES. Select YES to make
this a Master user level with the authority to access all User
Menu functions.
Select NO to make this a Standard user level. The following
options can then be selected:
7a. TEMP CODE NO YES.
Select NO to make this a permanent user code.
Select YES to make this a temporary code that automatically
expires in 7 days. Temporary codes are ideal for guests
or service technicians. You can delete a Temporary user
code at any time before the 7 day active period ends.
7b. ARM ONLY NO YES.
Select NO to allow this user to arm and disarm the system
and access all Standard level functions in the User Menu.
Select YES to restrict this user to arming only.
(The Arm Only user code can bypass zones not in a normal
condition at the time of arming.)
8. After you have completed making your selections, the
keypad display shows USER # ADDED.
9. Press the Back Arrow key once to add another user or twice
to exit the User Menu.
Deleting User Codes
1. Access the User Menu.
2. Press the COMMAND key until USER CODES? displays.
3. Press any one of the Select keys. The keypad displays ADD
DEL CHG.
4. Press the Select key under DEL to delete a user code from
the system. You must have a Master user code level to be able
to delete a user code.
5. At the USER NUMBER: - prompt, enter the user number you
want to delete and press COMMAND. The displays changes to
USER # DELETED.
6. The display then changes back to USER NUMBER: - for you
to delete another user. Press the Back Arrow key twice to
exit the User Menu.
Ambush Codes
Your system may be programmed to allow user number 1 to be an
Ambush code. The Ambush code functions identically to other
codes with the exception that it sends a silent alarm to the
central station. This silent alarm alerts the operator to a duress
situation at the premises and prompts the immediate notification
of the authorities.
Refer to the System Setup section of this guide to see if your
system is programmed for Ambush. If so, do NOT program a code
for user number 1 if you intend to use the Ambush function.
XRSuper6 User Menu
17
Changing User codes
1. Access the User Menu.
2. Press the COMMAND key until USER CODES? displays.
3. Press any one of the Select keys. The keypad displays ADD
DEL CHG.
4. Press the Select key under CHG to change a user code. You
must have a Master user code level to change a user code.
5. At the USER NUMBER:
- prompt, enter the user number to
change and press COMMAND.
6. The display changes to CODE NO: * * * *. Enter the new
4-digit user code and press COMMAND. If the code you
entered is already in use, or is a code used internally by the
system, the keypad displays ALREADY IN USE. You must enter
a different 4-digit user code.
7. If you are changing a code other than your own, the keypad
next displays MASTER? NO YES. Select YES if you want this
user to have a Master authority level.
Select NO if you want this user to have a Standard authority
level. If you select NO, refer to item number 7 in the Adding
User Codes section on the previous page.
Important: Changing a user code does not change the user
number. User number two may have their user code changed
from 1234 to 5678 but they are still user number two.
18
Date and Time
User Code Level: Master only.
Function: Allows you to change the current date and time
displayed on the keypad and used by the system for schedules
and Display Events.
Setting the Date and Time
1. Access the User Menu.
2. Press COMMAND until TIME? displays. Press any Select key.
3. The keypad displays the current day and time. Press the
COMMAND key to display the current date. Press the
COMMAND key again to make any changes.
4. The keypad displays TIME DAY DATE.
5. Press the Select key under TIME to change the time. The
keypad displays – :
AM PM. Enter the current time and
select AM or PM.
The display changes back to TIME DAY DATE.
6. Press the Select key under DAY to change the day of the
week. The keypad displays SUN MON TUE WED. If the current
day is not displayed, press the COMMAND key. Press the
Select key under the correct day.
7. Press the Select key under DATE to change the date. The
keypad displays:
MONTH: - Enter one or two digits for the month. Press
COMMAND.
DAY: - Enter up to two digits for the day. Press COMMAND.
YEAR: - Enter up to two digits for the year. Press COMMAND.
The display returns to TIME DAY DATE. Press the Back Arrow
key to exit the User Menu.
XRSuper6 User Menu
Display Events
Zone Activity Check Event Display
User Code Level: Master or Standard.
This displays the date and time the Zone Activity Check was
enabled or disabled.
Function: Allows you to review up to 60 past events that occurred
on your system from any keypad.
Once 60 events are stored, any new
Select keys
event causes the oldest event to be
cleared.
POWER
Note: This section shows the User's
Guide Display Events items for both
16-character (single line) and
32-character keypad displays. While
in the Display Events function, use
the COMMAND and Back Arrow keys
to go forward or
Back Arrow key
backward through the
list of events.
ARMED
JONES RESIDENCE
F R I 2 : 51 AM
1
2
AB C
5
3
DEF
6
MN O
9
PQR
0
4
GHI
JKL
8
7
S TU
16-Character Display
Description
ACT ENABLED 10/17
The Zone Activity Check was enabled
on October 17.
32-Character Display
Description
5:18P 10/17
ACT DISABLED
The Zone Activity Check was disabled
on October 17, at 5:18 PM
VWX
COMMAND
YZ
COMMAND key
Activity Check Event Types - There are 3 event types:
ACT DISABLED
ACT ENABLED
NO ZONE ACTIVITY
Using the Display Events Function
1. Access the User Menu.
2. Press the COMMAND key until DISPLAY EVENTS? displays.
Press any Select key.
3. The keypad displays FIRST LAST. Select FIRST to view events
starting from the oldest to the newest. Select LAST to view
events starting from the newest to the oldest.
If you select FIRST, use the COMMAND key to scroll up
through the events displays.
If you select LAST, use the Back Arrow key to scroll down
through the event displays.
XRSuper6 User Menu
19
Zone Bypass Event Displays
Zone Event Displays
This displays the bypassing of system zones.
This section displays alarms, troubles, and other events that could
occur on your protection zones.
16-Character Display
Description
26 BYPS 1 2 1017
Zone 26 bypassed by user 12. Press
the left Select key for the zone name
and the right Select key for the time.
32-Character Display
Description
BYP 5:18P 10 / 17
EAST W INDOW
The east window zone was bypassed.
Press a Select key for the zone
number and user number.
Bypass Event Types - There are 3 event types:
BYP - Bypass
RST - Restore
FRC - Force Arm
Note: You may sometimes see the user as SWG. This is short for
Swinger Bypass, which is an automatic function that allows the
system to bypass a zone. This section displays alarms, troubles,
and other events that could occur on your protection zones.
16-Character Display
Description
2 BURG ALR 1017
A burglary alarm occurred on zone 2.
Press the right Select key for the time
the alarm occurred.
32-Character Display
Description
A LR 10: 23P 10/17
BASEM ENT DOOR
An alarm occurred at 10:23 PM
on Oct 17. Press any Select key to
see the zone number and zone type.
Zone Type - There are 7 possible zone types you may see here.
FIRE - Fire
EMRG - Emergency
AUX1 - Auxiliary 1
PANC - Panic
SUPV - Supervisory
AUX2 - Auxiliary 2
BURG - Burglary
Event Types - There are 7 event types you may see here:
ALR - Alarm
TBL - Trouble
RST - Restore
LOW - Low battery
MIS - Missing xmitter
FLT - Zone Fault
SVC - Service Smoke Detector
Note: LOW and MIS are for wireless systems only.
20
XRSuper6 User Menu
Arming and Disarming Event Displays
User Code Change Event Displays
This displays any arming or disarming of system areas.
This displays any addition, deletion, or change to a user code.
16-Character Display
Description
16-Character Display
Description
ARM
Area 3 has been armed by user 12. Press
the left Select key for the area name.
Press the right Select key for the time
the arming occurred.
12 ADD 19 1017
User 12 added user 19 on Oct. 17.
Press the right Select key for the time
this occurred.
32-Character Display
Description
User 14 added by user 16 at 11:41
AM on October 17.
3
12
1017
32-Character Display
Description
A RM 5:10P 10/ 17
The Perimeter was armed at 5:10 PM.
A DD 11: 41A 10 / 17
US:14 BY US:16
Press any Select key to display the area
number and user number.
User Code Event Types - There are 3 event type you may see:
PERI M ET ER
Arming Event Types - There are 2 event type you may see here:
ARM - User armed the system DIS - User disarmed the system
User Check-in Event Displays
This shows when a user selected the pager Check-in feature from
the User Menu. See page 11 for more information.
16-Character Display
Description
CHECKIN 16 1017
User 16 selected the Check-in feature
on Oct. 17. Press the right Select key
for the Check-in time.
32-Character Display
Description
MSG 3: 31P 10 / 17
CHECKIN USER: 16
User 16 selected the Check-in feature
at 3:31 PM on Oct. 17.
XRSuper6 User Menu
ADD - User added
DEL - User deleted
CHG - User code or authority level has been changed.
Supervisory Event Displays
This displays the date and time of an automatic test report.
16-Character Display
Description
AUTO RECALL 1017
The test report was sent on Oct. 17.
32-Character Display
Description
MSG 11: 58P 10 / 17
AUTO RECALL
The test report was sent to the
Central station at the date and time
shown.
21
System Monitor Event Displays
Service Request?
This displays any loss of the system's AC power or battery.
User Code Level: Master only
16-Character Display
Description
POWER T BL 1017
An AC failure occurred on the system.
Press the right Select key for the time.
32-Character Display
Description
TBL 1: 05A 10 / 17
A C POW ER
An AC failure occurred at 1:05 AM.
System Monitor Event Types - There are 2 event types:
TBL - Trouble
RST - Restore
System Monitor Event Names - There are 2 system monitors:
AC POWER
BATTERY
Function: Allows you to send a Request for Service message to
the central station when there is a problem on your system.
After the Display Events function in the keypad User Menu, you
will see the SERVICE REQUEST? display if it has been programmed
for your user code. If this feature has been programmed, and
you would like to send a Request for Service report to the central
station, press any top row Select key while SERVICE REQUEST? is
displayed. After the Request for Service report is sent, the keypad
displays REQUEST MADE for four seconds.
If there is a problem with the telephone line connected to the
system, you must contact our service department directly for
assistance.
Note: This feature is not displayed if it has not been enabled on
your system.
22
XRSuper6 User Menu
System Setup
We have provided this System Setup section to allow you to track
the current status of the programmable options on your Security
Command system. If you make changes to the system, you should
update the information contained on these pages.
My system is monitored by a central station.
Protection Areas
Number
Description
1
_______________________________________________
2
_______________________________________________
C/S Name: __________________________________________
3
_______________________________________________
Address: ____________________________________________
4
_______________________________________________
❏ Yes
❏ No
City/State: __________________________________________
Emergency Phone: ___________________________________
Service Phone: ______________________________________
Outputs
Service Manager: ____________________________________
Your system has 4 outputs that can be used for various functions.
Below is a list of these outputs and the devices they control.
My system sends Opening and Closing reports.
Output #
❏ Yes
❏ No
My system sends Zone Bypass reports.
❏ Yes
❏ No
My system sends Ambush reports.
❏ Yes
❏ No
My system sends Abort reports.
❏ Yes
❏ No
XRSuper6 System Setup
What it controls
1
_______________________________________________
2
_______________________________________________
3
_______________________________________________
4
_______________________________________________
Enter the Output number above when using the Outputs On Off
User Menu option to manually toggle the outputs.
User Codes
Your system provides 16 user codes you can program for individual users. As you add new users or change current users' codes, you
can keep track of their name, user number, and other information here in this section. Use a pencil to allow for changes.
User
User Name
Level Temp Code Arm Only
HOW TO FILL IN THIS
TABLE
1
M S
Y N
Y N
2
M S
Y N
Y N
3
M S
Y N
Y N
4
M S
Y N
Y N
5
M S
Y N
Y N
Temp Code - Is this code set to expire
after seven days?
6
M S
Y N
Y N
7
M S
Y N
Y N
Arm Only - Is this user restricted to
just arming?
8
M S
Y N
Y N
9
M S
Y N
Y N
10
M S
Y N
Y N
11
M S
Y N
Y N
12
M S
Y N
Y N
13
M S
Y N
Y N
14
M S
Y N
Y N
15
M S
Y N
Y N
16
M S
Y N
Y N
24
User - The User Number of the person
authorized to use the system.
Level - Master or Standard authority.
Refer to the User Codes section of
this User's Guide for additional
information.
Circle Your Selections
XRSuper6 System Setup
Easy Entry™ User's Guide
This section of the user's guide provides information on using the Easy Entry™ access control capability of the security command
system. If your system is not currently using any access control devices, disregard this section. Easy Entry™ is built into every Security
Command system and can be accessed using Easy Entry™ keypads.
There are three different operating modes: Door Strike, Arming and Disarming, and Entry Delay. All of the examples below assume that
your system requires a user code to arm and disarm the
ABC SECURITY
protection.
FRI
2: 5 1 A M
DOOR STRIKE
All/Perimeter Door Strike - From the Status List, present your
card to the reader. Once it is validated by the system, the Door
Strike relay activates. See Door Strike Relay Operation above.
Home/Away systems only activate the Door Strike relay when
arming and disarming.
XRSuper6 Appendix
POWER
While the keypad is in
the Status List, present
your access card.
The relay activates for five
seconds during which
you must open the door.
Once you open the door,
you have 40 seconds to
exit and close the door
before the zone 2 SoftShunt expires.
ARMING AND DISARMING AN ALL/PERIMETER SYSTEM
Press Command. The keypad displays PERIM ALL (when arming) or DISARM?.
Press the Select key under the option. The keypad displays ENTER CODE: -.
Present your card to the reader. Once it is validated by the system, both areas
arm or disarm automatically and the Door Strike relay activates.
PERIM
ALL
The system arms or
disarms the areas and
activates the Door
Strike relay.
or
DISARM?
POWER
ARMING AND DISARMING A HOME/AWAY SYSTEM
Present your card to the reader. If the system is armed, once the card is validated all
areas are disarmed.
ABC SECURITY
FRI
2: 5 1 A M
POWER
If the system is disarmed when you present your card, once it is validated all areas are
armed in the AWAY mode.
ENTRY DELAY
All Systems - Once the protected door is opened and the entry
delay starts, the keypad displays ENTER CODE: -. Present your card
to the reader and, once it is validated, the system disarms all areas
accessible by you and activates the Door Strike relay. See Arming
and Disarming.
ABC SECURITY
ENTER CODE: POWER
POWER
Access door is
opened.
Using the access reader for user menu access
You can also use a card reader to access the User Menu when the
MENU? NO YES display is shown.
26
The system disarms the areas and activates the Door Strike
relay. See Arming and Disarming.
XRSuper6 Appendix
FA113 User's Guide
These instructions guide you through the operation of the XRSuper6 Command Processor system using the FA113 Wireless Keychain
Remote. The FA113 uses the audible output capability of the Security Command keypad to sound confirmation tones. It is recommended
that you use the FA113 within hearing distance of these keypads.
Arming a Home/Away or All/Perimeter System
1. Press the ON button once to arm the Perimeter burglary protection. The Security Command keypads emit a single beep to confirm
the arming. The Perimeter arms and all non-priority zones not in a normal condition are force armed.
2. After the single beep, press the ON button a second time to arm the Interior burglary protection. The Security Command keypads
emit two beeps to confirm the arming.
3. After the two beeps, pressing the ON button in Home/Sleep/Away systems arms the Bedrooms burglary protection. The Security
Command keypads emit three beeps to confirm the arming.
Disarming a Home/Away or All/Perimeter System
1. Press the OFF button once. The Security Command keypads emit a single 2-second beep to confirm the disarming.
Using the ALERT Buttons
Pressing the two ALERT buttons simultaneously sends a Panic alarm to the panel. If your system is monitored by a central station, the
proper authorities will be notified of the alarm.
XRSuper6 Appendix
Pager Direct™ User's Guide
Pager Direct uses the reporting capability of your security system to dial your pager number and send reports in much the same way
as someone sending you a pager message would do. You can receive reports of alarms, troubles, or armings and disarmings of the
system and know at a glance the status of your system.
Area Names
List your system's area names and numbers below:
Area
Name
Area
Name
1 _____________________ 3_____________________
2 _____________________
4 ____________________
Service Department Phone: ______________________
Emergency Phone: _____________________________
Central Station Phone: ____________________________
Fold
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
Pager Direct™
○
○
○
○
○
Fold
Security Command Numeric Paging
Cut along dotted lines
28
XRSuper6 Appendix
Numeric Pager Display
00128-301 2340010
Account Message Always
Area Always User
Number
ID
Zero Number Zero Number
Account Number
This number has been programmed into your Security Command
system as an identifier. Whenever the system sends a message
to your pager, it will always send the account number first to
identify itself.
Message ID
This is always a single digit, 1 to 7, that describes the message
s
e
n
t
.
1 = Zone Alarm
5 = Late To Close
2 = Zone Trouble
6
=
User
Check-in
3 = Area(s) Arming
7 = Local Message
4 = Area(s) Disarming
Zone or Area Number
If this message is for a zone, the 1- to 2-digit zone number is
displayed. If this message is for areas that are being armed or
disarmed, the area numbers are shown in sequential order.
For example, 1 2 4.
User Number
This is a 3-digit number, that identifies the user.
Security Command Numeric Paging
XRSuper6 Appendix
PhoneAccess™ User's Guide
This exciting feature allows you to call your XRSuper6 system from any outside touch-tone phone to arm and disarm protection areas
or turn on or off the panel's relay outputs.
Quick Reference Wallet Card
How it works
1. Call the system's phone number from a touch-tone phone.
2. The system answers the call and sounds a short ready tone.
You now have 8 seconds to enter a valid Master user code. If the
user code is accepted by the panel, you will hear one or more
beeps giving you the current armed status of the system. (Press
the * key at any time to hear the armed status of the system.)
If
You will hear
All areas are armed
Area 1 (Perimeter) is armed
Any area is armed
All areas are disarmed
3
1
2
1
short beeps
short beep
short beeps
long beep
If the user code is not accepted by the panel, you will hear four
short beeps. Check the user code and try again. After 3
unsuccessful attempts, the panel locks out PhoneAccess™ until
a valid user code is entered at a keypad on the system.
3. Once the user code is accepted by the panel and the armed
status is given, you can enter the following commands:
Press
For this action
You will hear
#, 1
Arm all
3 short beeps
#, 2
Arm Perimeter
1 short beep
#, 3
Arm Perimeter/Interior 2 short beeps
#, 0
Disarm all areas*
1 long beep
#, 5, 4, 0, n* Toggles the output
1 short beep = on
1 long beep = off
(* Use outputs 1, 2, 3, or 4 in place of
n)
4 short beeps = restricted
PhoneAccess™ Quick Commands
Press
# then 1
# then 2
# then 3
To do this
Arm all areas
Arm area 1
Arm areas 1 & 2
You will hear
3 short beeps
1 short beep
2 short beeps
Note: Zones in a bad condition are force armed when the area arms.
# then 0
Disarm all areas
1 long beep
#, 5, 4, 0, n*
Toggles the output 1 short beep = on
(* Use outputs 1, 2, 3, or 4 in place of n) 1 long beep = off
(Enter output descriptions below)
4 short beeps = restricted
1. _________________________ 3. _________________________
2. _________________________ 4.
_________________________
PhoneAccess™ Quick Commands
Press
# then 1
# then 2
# then 3
To do this
Arm all areas
Arm area 1
Arm areas 1 & 2
You will hear
3 short beeps
1 short beep
2 short beeps
Note: Zones in a bad condition are force armed when the area arms.
# then 0
Disarm all areas
1 long beep
#, 5, 4, 0, n*
Toggles the output 1 short beep = on
(* Use outputs 1, 2, 3, or 4 in place of n) 1 long beep = off
(Enter output descriptions below)
4 short beeps = restricted
1. _________________________ 3. _________________________
2. _________________________ 4.
_________________________
Cut along dotted lines
30
XRSuper6 Appendix
1. Call the panel phone number. The panel answers and sounds
one short tone.
2. Enter your code within 8 seconds. One beep means the code
is good. Four short beeps means enter it again. You have 3
tries.
3. You have 30 seconds to enter the first command (see other
side) and 30 seconds for each additional command.
If
You will hear
All areas are armed
Area 1 (Perim) is armed
Any area is armed
All areas are disarmed
3 short beeps
1 short beep
2 short beeps
1 long beep
895 Voice Module
You can also use the 895 Voice Module with the XRSuper6
Command Processor™ panel. The 895 allows you to call your
security system using a touch-tone telephone, and perform a
variety of functions, ranging from arming and disarming to changing
user codes. The 895 operates much like a voice mail system,
providing you with easy to follow English language prompts.
The 895 Voice Module provides you with easy-to-understand
prompts that lead you through the steps to control your security
system. Using your present User Code and User Code Level, you
will have access to the same options of your system using the 895
as you would when using a keypad to control your security system.
1. Call the panel phone number. The panel answers and sounds
one short tone.
The 895 Voice Module easily mounts into the enclosure presently
housing your XRSuper6 Command Processor™ panel. The standard
three-hole configuration allows for easy and quick installation.
2. Enter your code within 8 seconds. One beep means the code
is good. Four short beeps means enter it again. You have 3
tries.
For more information about the 895 Voice Module, refer to LT0421, the 895 Voice Module User's Guide.
3. You have 30 seconds to enter the first command (see other
side) and 30 seconds for each additional command.
If
You will hear
All areas are armed
Area 1 (Perim) is armed
Any area is armed
All areas are disarmed
3 short beeps
1 short beep
2 short beeps
1 long beep
XRSuper6 Appendix
Common Keypad Displays
Listed below are several keypad messages you may see on the display. Follow the instructions in the Possible Solutions column to
correct the problem. In most cases, you will need to call a service person to correct the problem.
Message
Keypad
Tone
Invalid Code
No
The user code you have entered is not
recognized by the system.
Check the user code and try again.
AC Trouble
Yes
The system is not getting proper power.
Call your service person.
Battery Trouble
Yes
Battery is either low or missing.
Call your service person.
Phone Line Trouble
Yes
The panel is looking for phone jack
supervision.
Call your service person.
System Trouble or
Service Required
Yes
There is a problem with one or more of the
Call your service person.
components in the system.
System Busy
No
The system is performing another task with Wait a few moments for the system to finish the task. Call your
a higher priority.
service person if problem remains.
Meaning
Possible Solutions
There is not a supervised device on bus.
4-Wire Bus Trouble
No
Low Voltage or an open yellow wire.
Call your service person.
Two devices are on the same address.
Transmit Fail
Yes
The panel has attempted to communicate
with the central station 10 times and has
not succeeded.
Wireless Trouble
Yes
The wireless receiver is not communicating
Call your service person.
with the 472 Inovonics 900MHz Interface.
Non-Polled Address
32
770
Keypad Keypad is set to an invalid address.
Only
Make sure your telephone line is working properly. Call your
service person if problem remains.
Call your service person.
XRSuper6 Appendix
Index
Symbols
24-Hour Zone 2
895 Voice Module 31
A
AC LED 4
ALERT Buttons 27
Ambush Codes 17
Areas 2
Arm and Disarm Events 21
Armed LED 4
Arming
All/Perimeter system 7
Home/Away system 9
Instant 7
B
Back Arrow key 4
Bypassing zones 14
C
COMMAND key 4
XRSuper6 Appendix
D
F
S
Data entry keys 4
Date and Time 18
Disarming
FA113 instructions 27
Security System Terms 2
Select keys 4
Sensor Reset 13
Service Request 22
Supervisory Events 21
System Monitor Events 22
System Ready/System Not
Ready 7, 9
System Setup 23
System Test 15
All/Perimeter system 8
Home/Away system 10
Display brightness 4
Display Events. See Event
Displays
Door Strike 25
I
Instant Zone 2
Introduction 1
L
LCD Keypad
Messages 5
Tone, adjusting 4
Tones 5
Volume, setting 4
E
Easy Entry feature 25
Entry Delay 26
Entry or Exit Zone 2
Event Displays
Arming and Disarming 21
Supervisory 21
System Monitor 22
User Check-in 21
User Code Change 21
Zone 20
Zone Activity Check 19
Zone Bypass 20
Exit Error 3
M
Monitoring Zones 14
O
T
Testing the System 15
U
Outputs 13
User Check-in 12
P
User Code
Pager Direct 28
PhoneAccess 30
R
Resetting Sensors 13
Displaying in Events 21
Displaying Events 21
User Codes 16
List 24
Z
Zone 2
Activity Check 12, 19
Events 20
Monitor 14.
See also Monitoring Zones (LED)
Status 3
This page has been intentionally left blank.
LT-0622 (10/02)