PSC QuickScanQS6500BT Technical data

QuickScanTM QS6500BT
General Purpose Handheld Linear Imager Bar Code
Reader with Bluetooth® Wireless Technology
Quick Reference Guide
Datalogic Scanning, Inc.
959 Terry Street
Eugene, Oregon 97402
Telephone: (541) 683-5700
Fax: (541) 345-7140
An Unpublished Work - All rights reserved. No part of the contents of
this documentation or the procedures described therein may be reproduced or transmitted in any form or by any means without prior written
permission of Datalogic Scanning, Inc. or its subsidiaries or affiliates
("Datalogic" or “Datalogic Scanning”). Owners of Datalogic products are
hereby granted a non-exclusive, revocable license to reproduce and
transmit this documentation for the purchaser's own internal business
purposes. Purchaser shall not remove or alter any proprietary notices,
including copyright notices, contained in this documentation and shall
ensure that all notices appear on any reproductions of the documentation.
Should future revisions of this manual be published, you can acquire
printed versions by contacting your Datalogic representative. Electronic
versions may either be downloadable from the Datalogic website
(www.scanning.datalogic.com) or provided on appropriate media. If
you visit our website and would like to make comments or suggestions
about this or other Datalogic publications, please let us know via the
"Contact Datalogic" page.
Disclaimer
Datalogic has taken reasonable measures to provide information in this
manual that is complete and accurate, however, Datalogic reserves the
right to change any specification at any time without prior notice.
Datalogic and the Datalogic logo are registered trademarks of Datalogic
S.p.A. in many countries, including the U.S.A. and the E.U. All other
brand and product names may be trademarks of their respective owners.
QuickScan is a registered trademark of Datalogic Scanning, Inc. in
many countries, including the U.S.A. and the E.U.
This product may be covered by one or more of the following patents: 6,293,467 •
6,612,495 • 6,705,527 • Other Patents Pending
Datalogic Scanning, Inc.
QUICKSCANTM END USER LICENSE
AGREEMENT
Notice to End User: The Datalogic Product you have acquired contains embedded Software,
which is integral to the product’s operation. This Software is being provided to you under
license, subject to the terms and conditions of this Agreement. If you use the Datalogic
Product, you will be deemed to have accepted the terms and conditions of this Agreement.
If you do not intend to be bound to the terms of this Agreement, Datalogic is not willing to
license the Software to you, you may not use the Datalogic Product or the Software, and you
must contact the party from whom you acquired the Datalogic Product for instructions.
This End User Software License Agreement ("Agreement") is a legally binding agreement governing the licensing of the Software and Documentation by Datalogic,Scanning Holdings, Inc. and its
subsidiaries and affiliates ("Datalogic") to the entity or person who has purchased or otherwise
acquired a Datalogic Product ("End User"). For purposes of this Agreement, any software that is
associated with a separate end-user license agreement is licensed to you under the terms of that
license agreement. Datalogic and End User hereby agree as follows:
1. Definitions.
1.1
1.2
1.3
1.4
"Documentation" means materials such as user’s guides, program reference guides, quick
reference guides, manuals, or similar materials associated with or related to the Datalogic
Product, whether in printed, “online”, or other form.
"Proprietary Information" means: (a) source code, object code, software, documentation,
and any related internal design, system design, data base design, algorithms, technology,
technical data or information, implementation techniques, and trade secrets related to the
Software, (b) any other trade secrets marked appropriately or identified as proprietary or
confidential, and (c) any information that End User, under the circumstances, should recognize as confidential. Proprietary Information does not include any information that the receiving party can establish was (1) in the public domain, (2) already in the receiving party’s
possession or rightfully known prior to receipt, (3) rightfully learned from a third party not in
violation of any other's proprietary rights, or (4) independently developed without access to
Proprietary Information.
“Datalogic Product” means the Datalogic® QuickscanTM series scanner product, including all
embedded Software in and all Documentation related to such product, which has been purchased or otherwise acquired by End User, whether obtained directly or indirectly from Datalogic.
"Software" means any software or computer programs of Datalogic or its third party licensors in machine readable form which is embedded in the Datalogic Product, whether
obtained directly or indirectly from Datalogic, including any replacement, update, upgrade,
enhancement or modification.
2. Scope Of License Granted.
2.1
2.2
Datalogic grants to End User a non-exclusive, non-transferable, perpetual license to use the
Software, solely on the Datalogic Product in which it is embedded (“designated Datalogic
Product”), in machine-readable form only, solely for End User's internal business purposes.
This Agreement does not convey ownership of the Software to End User. Title to the Software shall be and remain with Datalogic or the third party from whom Datalogic has
obtained a licensed right. As used in this Agreement, the term “purchase” or its equivalents
when applied to the Software shall mean “acquire under license.” End User is not entitled to
receipt or use of the source code to any Software.
End User shall not copy, modify, decompile, disassemble, reverse engineer, or otherwise
reproduce or remanufacture the Software, whether modified or unmodified, nor sell, assign,
sublicense, distribute, lend, rent, give, or otherwise transfer the Software to any other person
or organization, for purposes other than as expressly provided in this Agreement, without
Datalogic’s prior written consent.
Quick Reference Guide
i
3. Transfers, Support.
3.1
3.2
3.3
Any copying, installing, reproduction, remanufacture, reverse engineering, electronic transfer, or other use of the Software on other than the designated Datalogic Product will be a
material breach of this Agreement. However, Datalogic may elect not to terminate this
Agreement or the granted licenses, but instead may elect to notify End User that End User is
deemed to have ordered and accepted a license for each breaching use. End User shall pay
Datalogic the applicable list price for such licenses as of the date of such breach.
End User shall not sell, assign, sublicense, distribute, lend, rent, give, or otherwise transfer
the Datalogic Product to any third party unless such third party agrees with Datalogic in writing to be bound by the terms and conditions of this Agreement. Any such transfer of the Datalogic Product absent such agreement shall be null and void.
End User may obtain support for Software from Datalogic at Datalogic’s standard support
fees and under Datalogic’s standard support terms and conditions in effect at the time the
support is requested.
4. Intellectual Property.
End User acknowledges that the Software constitutes valuable trade secrets of Datalogic or Datalogic’s third party licensors and that the Software is protected by intellectual property laws and treaties. The license set forth in this Agreement does not transfer to End User any ownership of
Datalogic’s or its third party licensors' copyrights, patents, trademarks, service marks, trade
secrets, or other intellectual property rights and End User shall have no right to commence any
legal actions to obtain such rights. End User shall not remove, modify, or take any other action that
would obscure any copyright, trademark, patent marking, or other intellectual property notices contained in or on the Datalogic Product.
5. Proprietary Information.
5.1
5.2
5.3
End User acknowledges that Proprietary Information is the confidential, proprietary, and
trade secret property of Datalogic and Datalogic’s third party licensors and End User
acquires no right or interest in any Proprietary Information.
End User shall not disclose, provide, or otherwise make available the Proprietary Information
of Datalogic or its third party licensors to any person other than End User’s authorized
employees or agents who are under confidentiality agreement, and End User shall not use
the Proprietary Information other than in conjunction with use of the Datalogic Product exclusively for End User’s internal business purposes. End User shall take steps to protect the
Proprietary Information no less securely than if it were End User's own intellectual property.
The provisions of this Proprietary Information Section shall survive and continue for five (5)
years after the termination of this Agreement.
6. Limited Warranty.
6.1
6.2
ii
Datalogic warrants that, under normal use and operation, the Datalogic Product will conform
substantially to the applicable Documentation for the period specified in the Documentation.
During this period, for all reproducible nonconformities for which Datalogic has been given
written notice, Datalogic will use commercially reasonable efforts to remedy nonconformities
verified by Datalogic. End User agrees to supply Datalogic with all reasonably requested
information and assistance necessary to help Datalogic in remedying such nonconformities.
For all defects reported to Datalogic within the warranty period, Datalogic’s liability is limited
to providing End User with one copy of corrections or responding to End User's problem
reports according to Datalogic's standard assistance practices. Datalogic does not warrant
that the product will meet End User's requirements or that use of the product will be uninterrupted or error free, or that Datalogic's remedial efforts will correct any nonconformance.
This limited warranty does not cover any product that have been subjected to damage or
abuse, whether intentionally, accidentally, or by neglect, or to unauthorized repair or unauthorized installation, and shall be void if End User modifies the product, uses the product in
any manner other than as established in the Documentation, or if End User breaches any of
the provisions of this Agreement.
EXCEPT AS PROVIDED IN THIS AGREEMENT, THE DATALOGIC PRODUCT IS PROVIDED “AS IS” AND DATALOGIC MAKES NO WARRANTIES OF ANY KIND, EXPRESS OR
IMPLIED, WRITTEN OR ORAL, WITH RESPECT TO THE PRODUCT, AND SPECIFICALLY
DISCLAIMS THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE.
QuickScanTM QS6500BT
7. Infringement.
7.1
7.2
7.3
7.4
Datalogic will defend End User against any claim in a lawsuit that the Datalogic Product furnished hereunder infringe a United States patent or copyright of a third party and Datalogic
will pay any damages finally awarded against End User by a court of competent jurisdiction
that are attributable to such claim or will pay End User’s part of any settlement that is attributable to such claim, provided, that 1) End User notifies Datalogic promptly in writing of the
claim, 2) Datalogic controls the defense or settlement of the claim, and 3) End User cooperates fully with Datalogic in such defense or settlement. All notices of a claim should be sent
to Datalogic Scanning, Inc., Legal Department, 111 SW Fifth Ave. Suite 4100, Portland, OR
97204-3644.
In the defense or settlement of any such claim, Datalogic may, at its option, 1) procure for
End User the right to continue using the Datalogic Product, 2) modify the Datalogic Product
so that it becomes non-infringing, 3) replace the Datalogic Product with an equivalent product not subject to such claim, or 4) provide End User an opportunity to return the Datalogic
Product and receive a refund of the purchase price paid, less a reasonable allowance for
use.
Datalogic shall have no liability to End User for claims of infringement based upon 1) the use
of any Datalogic Product in combination with any product which Datalogic has not either furnished or authorized for use with such Datalogic Product 2) the use of any Datalogic Product
designed, manufactured, or modified to the specifications of End User, or 3) End User’s
modification of the Datalogic Product without written authorization from Datalogic.
THE FOREGOING STATES DATALOGIC’S COMPLETE AND ENTIRE OBLIGATION CONCERNING CLAIMS OF PATENT, COPYRIGHT, OR OTHER INTELLECTUAL PROPERTY
INFRINGEMENT, CANCELS AND SUPERCEDES ANY PRIOR AGREEMENTS,
WHETHER ORAL OR WRITTEN, BETWEEN THE PARTIES CONCERNING SUCH
CLAIMS, AND WILL NOT BE MODIFIED OR AMENDED BY ANY PAST, CONTEMPORANEOUS, OR FUTURE AGREEMENTS OR DEALINGS BETWEEN THE PARTIES,
WHETHER ORAL OR WRITTEN, EXCEPT AS SET FORTH IN A FUTURE WRITING
SIGNED BY BOTH PARTIES.
8. Limitation Of Liability.
EXCEPT AS PROVIDED IN SECTION 7, DATALOGIC SHALL NOT BE LIABLE FOR ANY CLAIMS
AGAINST END USER BY ANY OTHER PARTY. IN NO EVENT SHALL DATALOGIC'S LIABILITY
FOR DAMAGES, IF ANY, WHETHER BASED UPON CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY, STRICT LIABILITY, WARRANTY, OR ANY OTHER BASIS,
EXCEED THE PRICE OR FEE PAID BY END USER FOR THE DATALOGIC PRODUCT. UNDER
NO CIRCUMSTANCES SHALL DATALOGIC BE LIABLE TO END USER OR ANY THIRD PARTY
FOR LOST PROFITS, LOST DATA, INTERRUPTION OF BUSINESS OR SERVICE, OR FOR ANY
OTHER SPECIAL, CONSEQUENTIAL, CONTINGENT, INDIRECT, INCIDENTAL, PUNITIVE,
EXEMPLARY, OR OTHER SIMILAR DAMAGES, EVEN IF DATALOGIC HAS BEEN ADVISED OF
THE POSSIBILITY OF SUCH DAMAGES.
9. Government Restricted Rights; International Use.
9.1
9.2
Use, duplication, or disclosure of the Software by the U.S. Government is subject to the
restrictions for computer software developed at private expense as set forth in the U.S. Federal Acquisition Regulations at FAR 52.227-14(g), or 52.227-19 or in the Rights in Technical
Data and Computer Software clause at DFARS 252.227-7013(c)(1)(ii), whichever is applicable.
If End User is using the Datalogic Product outside of the United States, End User must comply with the applicable local laws of the country in which the Datalogic Product is used, with
U.S. export control laws, and with the English language version of this Agreement. The provisions of the “United Nations Convention on International Sale of Goods” shall not apply to
this Agreement.
10. Termination.
10.1
10.2
Either party may terminate this Agreement or any license granted under this Agreement at
any time upon written notice if the other party breaches any provision of this Agreement.
Upon termination of this Agreement, End User immediately shall cease using any nonembedded software and shall return to Datalogic or destroy all non-embedded software covered by this Agreement, and shall furnish Datalogic with a certificate of compliance with this
provision signed by an officer or authorized representative of End User. For embedded soft-
Quick Reference Guide
iii
ware, End User agrees to sign a waiver prepared by Datalogic concerning further use of the
embedded Software. End User’s resumed or continued use of the embedded Software after
termination shall constitute End User’s agreement to be bound by the terms and conditions
of this Agreement for such use.
11. General Provisions.
11.1
11.2
11.3
11.4
11.5
Entire Agreement; Amendment. This document contains the entire agreement between the
parties relating to the licensing of the Software and supersedes all prior or contemporaneous
agreements, written or oral, between the parties concerning the licensing of the Software.
This Agreement may not be changed, amended, or modified except by written document
signed by Datalogic.
Notice. All notices required or authorized under this Agreement shall be given in writing, and
shall be effective when received, with evidence of receipt. Notices to Datalogic shall be sent
to the attention of Contract Administration, Datalogic Scanning, Inc., 959 Terry Street,
Eugene, OR 97402, or such other address as may be specified by Datalogic in writing.
Waiver. A party’s failure to enforce any of the terms and conditions of this Agreement shall
not prevent the party’s later enforcement of such terms and conditions.
Governing Law; Venue:This Agreement and the rights of the parties hereunder shall be governed by and construed in accordance with the laws of the State of Oregon U.S.A, without
regard to the rules governing conflicts of law. The state or federal courts of the State of Oregon located in either Multnomah or Lane counties shall have exclusive jurisdiction over all
matters regarding this Agreement, except that Datalogic shall have the right, at its absolute
discretion, to initiate proceedings in the courts of any other state, country, or territory in
which End User resides, or in which any of End User's assets are located.
Attorneys’ Fees. In the event an action is brought to enforce the terms and conditions of this
Agreement, the prevailing party shall be entitled to reasonable attorneys’ fees, both at trial
and on appeal.
- END -
iv
QuickScanTM QS6500BT
NOTES
Quick Reference Guide
v
NOTES
vi
QuickScanTM QS6500BT
Installation
The QuickScanTM QS6500BT linear imager is easy to install and
use. The following figures show the steps to perform an installation. Turn off the host computer before connection. Consult the
host terminal’s manual if necessary.
1
2 I/F
8
Base
Station
Cable
Routing
3
Power
9
5
4
7
6
1. Lift the cable retainer.
2. Connect the interface (I/F) cable to the Base Station.
For Power Off Terminal application with standard USB interface, attach to USB 1.0, 1.1 or 2.0 host device ONLY.
NOTE
3. Connect the power cord to the Base Station.
4. Latch the cable retainer to secure the cables.
5. Route both cables through the notch.
6. Connect the I/F cable to the terminal’s communication port.
7. Connect the AC adapter to the wall outlet.
Quick Reference Guide
1
8. Place the linear imager in the Base Station and verify the
charge LED is flashing. After five minutes, the scanner will
have sufficient charge to begin reading labels. A full charge
from depleted battery will take approximately 2 hours.
9. Press and hold the link button on the bottom of the Base
Station for three seconds. This will ensure that any other
imager link to the Base Station will be broken. Upon unlinking, the Base Station will sound a short beep, followed by
two longer beeps, accompanied by a flashing amber LED.
10.Scan the bar code located on the label applied to the back
face of the Base Station. This will “link” the linear imager to
the Base Station. Upon successful link (which can take a few
seconds), the imager will sound a low-to-high pitched beep.
10
11
11.To verify scanning operation, point the linear imager at a bar
code and pull the trigger. The linear imager should emit a
beep indicating that the label has been scanned and transmitted to the Base Station successfully.
The linear imager installation is complete.
NOTE
2
A momentary press of the link button can be used to later
verify a link between the imager and Base Station. A good
link is indicated by six short beeps. The Base Statioin notes
an unlinked situation by slowly flashing an amber LED.
QuickScanTM QS6500BT
Battery Warnings and Cautions
WARNING
Do not discharge the battery using any device except for the
linear imager. When the battery is used in devices other than
the linear imager, it may damage the battery or reduce its life
expectancy. If the device causes an abnormal current to flow,
it may cause the battery to become hot, explode or ignite and
cause serious injury.
Lithium-ion battery packs may get hot, explode or ignite and
cause serious injury if exposed to abusive conditions. Be
sure to follow the safety warnings listed below:
• Do not place the battery pack in fire or heat.
• Do not connect the positive terminal and negative terminal of the battery pack to each other with any metal
object (such as wire).
• Do not carry or store the battery pack together with
metal objects.
• Do not pierce the battery pack with nails, strike it with a
hammer, step on it or otherwise subject it to strong
impacts or shocks.
• Do not solder directly onto the battery pack.
• Do not expose the battery pack to liquids, or allow the
battery to get wet.
In the event the battery pack leaks and the fluid gets into your
eye, do not rub the eye. Rinse well with water and immediately seek medical care. If left untreated, the battery fluid
could cause damage to the eye.
Quick Reference Guide
3
Always charge the battery at 32°–113°F (0°–45°C) temperature range.
CAUTION
Use only the authorized power supplies, battery pack, chargers, and docks supplied by your Datalogic reseller. The use
of any other power supplies can damage the linear imager
and void your warranty.
Do not disassemble or modify the battery. The battery contains safety and protection devices, which, if damaged, may
cause the battery to generate heat, explode or ignite.
Do not place the battery in or near fire, on stoves or other
high temperature locations.
Do not place the battery in direct sunlight, or use or store
the battery inside cars in hot weather. Doing so may cause
the battery to generate heat, explode or ignite. Using the
battery in this manner may also result in a loss of performance and a shortened life expectancy.
Do not place the battery in microwave ovens, high-pressure
containers or on induction cookware.
Immediately discontinue use of the battery if, while using,
charging or storing the battery, the battery emits an unusual
smell, feels hot, changes color or shape, or appears abnormal in any other way.
4
QuickScanTM QS6500BT
Power Supply
Models require either a Listed class II or class III with a Limited
Power Source (LPS). For the safety certification to be valid, class
III input power sources must be IEC/EN60950-1 (EN 60335series, EN 60065 or relevant) approved.
Input: 100 - 240 VAC Output: 9 - 12 VDC
Max. Current: 2.5 A
Max. Power: 30 W
For USB Power Off Terminal applications, attach to USB 1.0,
1.1 or 2.0 host device ONLY.
NOTE
LED and Beeper Indications
Some LED and Beeper indications are user-configurable. Those
listed in the following table are standard default settings. See the
Product Reference Guide (PRG) for programming information.
Condition
Powering On
Ready to Operate
Good Read
Error Indication
Quick Reference Guide
LED
Beeper
Bright Green Flash
Configurable as OFF
or ON DIM
Bright Green Flash
Red Flash
One Beep
None
One Beep
None
5
How to Scan
The figure below shows the right and wrong ways to scan a bar
code.
1
1
PDF
2
2
1. The linear imager must be pointed at a slight angle to the bar
code so that the light reflected off the bar code can be “seen”
by the linear imager. Do not hold the linear imager perpendicular to the bar code.
2. The targeting beam must cross the entire label. The linear
imager cannot read the bar code data without seeing the
entire label.
Scanning PDF417 Bar Codes
To read a PDF417 bar code, aim the targeting beam at the top of
the bar code, and in a smooth motion, scan down through the bar
code. You will hear a series of ticks, followed by a final beep when
the bar code’s content has been completely decoded. You may
need to sweep the bar code more than once in order to complete
the read.
6
QuickScanTM QS6500BT
Troubleshooting
If the linear imager is not operating properly, the following checks
should be performed:
1. The BT linear imager uses an internal battery and if the battery is fully depleted or failed, the linear imager will not
operate. Exchange the battery with a known good unit and
retest the linear imager.
uct
Prod ence
r
Refe ide
Gu
4
1
2
3
5
2. Verify the interface cable is securely attached to the host.
Consult your technical support personnel or refer to your
host system manual to verify the proper connection for the
linear imager.
3. Verify that the interface cable is securely attached to the Base
Station.
4. Check that the labels are of sufficient quality to be recognized by the linear imager. Wrinkled, smudged, or torn
labels can cause the linear imager to not read at all. Scan a
known good label to check the linear imager's read operation.
5. Ensure that the Base Station's interface type is compatible
with the host terminal by consulting your POS system manual and/or the linear imager’s Product Reference Guide
found on the CD included with your linear imager.
Quick Reference Guide
7
6. Verify that the Base Station power cable is securely attached
and the external power adapter is plugged in.
If the linear imager still does not function properly, contact your
local supplier or Datalogic Customer Support Services.
Statement of Compliance
This device complies with Part 15 of the FCC rules. Operation is
subject to the following conditions:
1. This device may not cause harmful interference; and
2. This device must accept any interference received, including
interference that may cause undesired operation.
FCC Class B Compliance Statement
This Equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with these instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
8
•
Reorient or relocate the receiving antenna
•
Increase the separation between the equipment and
receiver
QuickScanTM QS6500BT
•
Connect the equipment into an outlet on a circuit different from that to which receiver is connected
•
Consult the dealer or an experienced radio I TV technician for help.
FCC Caution statement
"The User is cautioned that changes or modifications not expresely approved by the part responsible for compliance could void
the user's authorify to operate the equipment."
LED Class
CLASS 1 LED PRODUCT
APPARECCHIO LED CLASSE 1
LED KLASSE 1
APPAREIL A LED DE CLASSE 1
EN60825-1/All:2001
Quick Reference Guide
9
NOTES
10
QuickScanTM QS6500BT
EC DECLARATION OF CONFORMITY
Datalogic hereby declares that the apparatus specified below and as referenced in the EC Type
Approval Certificate has been tested and found compliant to the following European Council Directives and harmonized Standards.
Equipment Type: Handheld Barcode Scanning Equipment
Apparatus: QuickscanTM QS6500BT with Base Station
Manufactured by:
Placed into EU Service:
Datalogic Scanning, Inc.
959 Terry St. Eugene, Oregon USA, 541-683-5700
Oct 2002 under PSC logo, May 2007 under Datalogic logo.
Updated June 2009
EMC 2004/1 08/EC (2004)
Low Voltage 2006/95/EC (2006)
EN 300 328 (2006)
Council Directives:
EN 301489-1/17 (2008)
R&TTE 1999/5/EC (1999)
Battery 2006/66/EC (2006) amended 2008/12/EC (2008)
Standards:
EN 55022: 2006 (Class B)
Description:
Generic Emissions
AN/NZS CISPR22:2006
Generic Emissions
EN 301489-1/17:2008
Generic Immunity to EN61000
4-2: 1995 + A1:1998 + A2:2001 (ESD),
4-3: 2006 + A1:2008 (susceptibility),
4-4: 2004 (EFT),
4-5: 2006 (surge),
4-6: 2007 (conducted immunity)
4-11: 2004 (VDl)
EN61000-3-2:2006
Harmonic Current (power supply)
EN61000-3-3 : 1995 +
A1:2001 + A2:2005
Voltage Fluctuation/Flicker (power supply)
EN/IEC 60950-1 :2001/ CB
Safety of ITE
United Nations
Manual of Tests and Criteria, Section 38.3
ST/SG/AC.10/11/Rev.3
Lithium batteries
UL2054
Safety for household and commercial batteries
A technical construction file for this apparatus is retained at the above address.
Declaration of Conformity with Regard to the R&TTE Directive 1999/5/EC:
English:
This apparatus is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC
Français:
Cet équipement répond aux exigences et provisions de la Directive 1999/5/EC.
Deutsch:
Diese Geräte entsprechen den Anforderungen und anderen relevanten Bestinunungen der Richtlinie 1999/5/EC.
Italiano:
Questa apparecchiatura rispetta i requisiti essenziali e Ie altre clausole rilevanti della Direttiva 1999/5/CE.
Espanol:
Este equipo cumple con los requisitos esenciales y otras provisiones relevantes de la Directiva 1999/5/EC.
June 11, 2009
Brad West
Vice President, Supply Chain Operations
Datalogic Scanning, Inc.
Australia
Datalogic Scanning Pty Ltd
Telephone: [61] (2) 9870 3200
australia.scanning@datalogic.com
Japan
Datalogic Scanning KK
Telephone: 81 (0)3 3491 6761
japan.scanning@datalogic.com
France and Benelux
Datalogic Scanning SAS
Telephone: [33].01.64.86.71.00
france.scanning@datalogic.com
Latin America
Datalogic Scanning, Inc
Telephone: (305) 591-3222
latinamerica.scanning@datalogic.com
Germany
Datalogic Scanning GmbH
Telephone: 49 (0) 61 51/93 58-0
germany.scanning@datalogic.com
Singapore
Datalogic Scanning Singapore PTE LTD
Telephone: (65) 6435-1311
singapore.scanning@datalogic.com
India
Datalogic Scanning India
Telephone: 91- 22 - 64504739
india.scanning@datalogic.com
Iberia
Datalogic Scanning SAS Sucursal en España
Telephone: 34 91 746 28 60
spain.scanning@datalogic.com
Italy
Datalogic Scanning SpA
Telephone: [39] (0) 39/62903.1
italy.scanning@datalogic.com
United Kingdom
Datalogic Scanning LTD
Telephone: 44 (0) 1582 464900
uk.scanning@datalogic.com
www.scanning.datalogic.com
Datalogic Scanning, Inc.
959 Terry Street
Eugene, OR 97402
USA
Telephone: (541) 683-5700
Fax: (541) 345-7140
R44-3041 (Rev. A)
©2004-2009 Datalogic Scanning, Inc.
7/09