CD6KG
Dryer
Read this manual prior to initial operation of the product!
Dear Customer,
We hope that your product, which has been manufactured in modern facilities and
passed through a strict quality control procedure, will give you very good results.
We advise you to read through this manual carefully before using your product and keep
it for future reference.
This User Manual will
• Help you use your machine in a fast and safe way.
• Read the User Manual before installing and starting your product.
• In particular, follow the instructions related to safety.
• Keep this User Manual within easy reach for future reference.
• Please read all additional documents supplied with your product.
Remember that this User Manual is also applicable for several other models.
Explanation of symbols
Throughout this User Manual the following symbols are used:
Important safety information. Warning for hazardous situations with regard to life and property.
Caution; Warning for supply voltage.
Caution; Warning for fire hazard.
Caution; Warning for hot surfaces.
Read the instructions.
C
Useful information. Important information or useful hints about usage.
This appliance’s packaging material is recyclable. Help recycle it and protect the
environment by dropping it off in the municipal receptacles provided for this purpose.
Your appliance also contains a great amount of recyclable material. It is marked with
this label to indicate the used appliances that should not be mixed with other waste.
This way, the appliance recycling organised by your manufacturer will be done under
the best possible conditions, in compliance with European Directive 2002/96/EC on
Waste Electrical and Electronic Equipment. Contact your town hall or your retailer for the used
appliance collection points closest to your home. We thank you doing your part to protect the
environment.
Euromed_6kg/130313.1409
A
B
1
Important safety information
This section includes safety information
that will help protection from risks of
personal injuries or materialistic damages.
Failure to follow these instructions
shall cause any warranty and reliability
commitment to become void.
•
General safety
• Never place the machine on a carpetcovered floor, otherwise, lack of airflow
beneath the machine may cause
electrical parts to overheat. This will
cause problems with your machine.
• If the power cable or mains plug is
damaged, you must call Authorised
Service Agent for repair.
• The product should not be plugged
in during installation, maintenance
and repair works. Such works should
always be made by the technical
service. Manufacturer shall not be held
responsible for damages arising from
processes carried out by unauthorised
persons.
• Connect the product to a grounded
outlet protected by a fuse of suitable
capacity as stated in the technical
specifications table.
• Operate your product at temperatures
between +5°C and +35°C.
• Do not use electrical devices in the
product.
• Do not connect the air exit of the
product to the chimney holes which
are used for the exhaust fumes of the
devices operating with gas or other
types of fuel.
• You must provide enough ventilation
in order to prevent gases exiting from
devices operating with other types of
fuels including the naked flame from
accumulating in the room due to the
back fire effect.
• Always clean the lint filter before or after
each loading.
• Never operate your dryer without the
lint filter installed.
• Do not allow fibre, dust and dirt
accumulation around the exhaust exit
and at adjacent areas.
• Power cable plug must be within easy
reach after installation.
• Do not use extension cords, multi-plugs
3
•
•
•
•
•
•
•
•
EN
or adaptors to connect the dryer to
power supply in order to decrease the
risk of electric shock.
Do not make any changes on the plug
supplied with the product. If it is not
compatible with the socket, have a
qualified electrician change the socket
with a suitable one.
Items cleaned or washed with gasoil/
fuel oil, dry-laundry solvents and other
combustible or explosive materials as
well as the items that are contaminated
or spotted with such materials should
not be dried in the product since they
emit flammable or explosive vapor.
Do not dry items cleaned with industrial
chemicals in the dryer.
Do not dry unwashed items in the dryer.
Items soiled with cooking oils,
acetone, alcohol, fuel oil, kerosene,
stain remover, turpentine, paraffin and
paraffin removers must be washed
in hot water with plenty of detergent
before being dried in the dryer.
Garments or pillows bolstered with
rubber foam (latex foam), shower
bonnets, water resistant textiles,
materials with rubber reinforcement and
rubber foam pads should not be dried
in the dryer.
Do not use fabric softeners and
anti-static products unless they are
recommended by the manufacturers of
the fabric softener or the product.
Oil-affected items can ignite
spontaneously, especially when
exposed to heat sources such as in
a tumble dryer. The items become
warm, causing an oxidation reaction
in the oil. Oxidation creates heat. If the
heat cannot escape, the items can
become hot enough to catch fire. Piling,
stacking or storing oil-affected items
can prevent heat from escaping and so
create a fire hazard.
If it is unavoidable that fabrics that
contain vegetable or cooking oil or
have been contaminated by hair care
products be placed in a tumble dryer
they should first be washed in hot water
with extra detergent - this will reduce,
but not eliminate, the hazard.
• This product must be grounded.
Grounding installation decreases the
risk of electric shock by opening a path
with low resistance for the electricity
flow in case of a malfunction or failure.
Power cable of this product is equipped
with a conductor and a grounding
plug that allows for grounding the
product. This plug must be installed
appropriately and inserted into a socket
which is grounded in accordance with
the local laws and regulations.
• Do not install the product behind a door
with a lock, sliding door or a door that
has a hinge against the hinge of the
dryer.
• Do not install or leave this product
in places where it will be exposed to
outdoor conditions.
• Do not tamper with the controls.
• Do not perform any repair or part
replacing procedures on the product
even if you know or have the ability to
perform unless it is clearly suggested
in the operating instructions or the
published service manual.
• Inside and exhaust duct of the product
must be cleaned by the qualified
service personnel periodically.
• Wrong connection of grounding
conductor of the product can cause
electric shock. If you have any suspect
about the grounding connection, have
it checked by a qualified electrician,
service representative or service
personnel.
• Do not reach into the machine when
the drum is spinning.
• Unplug the machine when it is not in
use.
• Never wash down the appliance with
water! There is the risk of electric shock!
Always disconnect by unplugging from
the mains before cleaning.
• Never touch the plug with wet hands.
Never unplug by pulling on the cable,
always pull out by grabbing the plug
only. Do not operate the machine if the
power cable or plug is damaged!
• Never attempt to repair the machine
yourself, otherwise, you will be putting
your life and others’ lives in danger.
• For malfunctions that cannot be solved
by following the information given in the
safety instructions:
Turn off the machine, turn off and
contact an authorised service agent.
• Do not stop the dryer before the drying
cycle comes to an end unless you will
remove all laundry from the dryer fast
in order to lay them and dissipate the
heat.
• Remove the door of the drying
compartment before decommissioning
or disposing of the product.
• The final step of the drying cycle (cooldown cycle) occurs without applying
heat to ensure that the items are left
at a temperature that will not damage
them.
• Fabric softeners or similar products
should be used as specified by the
fabric softener instructions.
• Underwear that contains metal
reinforcements should not be placed in
a dryer. Damage to the dryer can result
if metal reinforcements come loose
during drying.
• Check all garments for forgotten
lighters, coins, metal pieces, needles,
etc. before loading.
• Remove all objects from pockets such
as lighters and matches.
• At times when your dryer is not in
use or after the laundry is taken out
following the completion of drying
process, turn off by using the On/
Off button. In cases when the On/
Off button is on (while the dryer is
energized), keep the door of the dryer
closed.
Intended use
• This product has been designed for
domestic use. It should not be used for
other purposes.
• Use the product only for drying laundry
that are marked accordingly.
• Dry only those articles in your product
that are stated in this manual.
• This product is not intended to be
used by persons with physical, sensory
or mental disorders or unlearned
or inexperienced people (including
children) unless they are attended by
a person who will be responsible for
their safety or who will instruct them
accordingly for use of the product.
4 EN
Children’s safety
• Electrical appliances are dangerous for
the children. Keep children away from
the machine when it is operating. Do
not let them tamper with the machine.
• Packaging materials are dangerous to
children. Keep the packaging materials
out of reach of children or dispose
them by classifying according to waste
directives.
• Do not allow children sit/climb on or
enter in the product.
• Children should be supervised to
ensure that they do not play with the
product.
• Close the loading door when you leave
the area where the product is located.
5 EN
2 Installation
Refer to the nearest Authorised Service
Agent for installation of your product.
CPreparation of location and electrical
installation for the product is under
customer’s responsibility.
BInstallation and electrical connections
must be carried out by a qualified
personnel.
APrior to installation, visually check if the
product has any defects on it. If so, do
not have it installed. Damaged products
will cause risks for your safety.
Appropriate installation location
• Install the product in an environment
which has no risk of freezing and is in a
stable and level position.
• Operate your product in a well
ventilated, dust-free environment.
• Do not block the air ducts in front of
and under the product with materials
such as long pile rugs and wooden
bands.
• Do not place your product on a long
pile rug or on similar surfaces.
• Do not install the product behind a door
with a lock, sliding door or a hinged
door which can strike the product.
• Once the product is installed, it should
stay at the same place where its
connections have been made. When
installing the product, make sure
that the rear wall of it does not touch
anywhere (tap, socket, etc.) and also
pay attention to install the product at a
place where it will stay permanently.
BDo not place the product on top of the
power cable.
• Keep at least 1.5 cm distance to walls
of other furniture.
Removing the transportation
safety assembly
ARemove the transportation safety
assembly before using the product for
the first time.
1. Open the loading door.
2. There is a nylon bag inside the drum
that contains a piece of styrofoam. Hold
it from its section marked with XX.
3. Pull the nylon towards yourself and
remove the transportation safety
assembly.
AMake sure that you have removed
the transportation safety assembly
(nylon+styrofoam pieces) before using
the product for the first time. Do not
leave any items inside the drum.
Under counter installation
• A special part (Part no. 297 360 0100)
replacing the top trim must be provided
and installed by the Authorised Service
Agent in order to use the machine under
a counter or in a cupboard. It should
never be operated without the top trim.
• Leave at least 3 cm of space between
the side and rear walls of the product
and the walls of the counter/cupboard
when installing your product under a
counter or in a cupboard.
Mounting over a washing machine
• A fitting device should be used between
the two machines when installing above
a washing machine. The bracket (Part
no. 297 720 0200 white/297 720 0500
grey) must be installed by the Authorised
Service Agent.
• Place the product on a firm floor. If
it will be placed on top of a washing
machine, the approximate weight of
both machines may reach 180 kg when
they are full. Therefore, the floor must be
capable of carrying the load on it!
Connecting the water drain hose for
models with the water tank at the
bottom;
Connection pipe to water drain is at the
bottom rear of your machine.
1. Remove the bracket and the rubber cap.
2. Attach the drain hose and replace the
bracket to its position.
6 EN
C Never unscrew the adjustable feet from
their housings.
Electrical connection
Connect the machine to a grounded outlet
protected by a fuse of suitable capacity as
stated in the technical specifications table.
Our company shall not be liable for any
damages that will arise when the machine
is used on a circuit without grounding.
• Connection must comply with national
regulations.
• If the current value of the fuse or
breaker in the house is less than 10
Amps, have a qualified electrician install
a 10 Amp fuse.
• Power cable plug must be within easy
reach after installation.
• The voltage and allowed fuse or
breaker protection are specified in the
“Technical Specifications” section.
• The specified voltage must be equal to
your mains voltage.
• Do not make connections via extension
cables or multi-plugs.
• The main fuse and switches must have
a contact distance of minimum 3 mm.
BDamaged power cable must only be
replaced by a qualified electrician.
BIf the product is faulty, it must not be
operated unless it is repaired! There is
the risk of electric shock!
Important:
C Make sure that the discharge hose is
tight after it is connected to the drain
in order to obtain a better water flow
since the machine is not equipped with
a pump. You can cut and shorten the
hose to adjust its length if necessary.
C The end of the hose should never be
higher than the level of the water outlet
on the machine. Otherwise, the “tank
full” light of your machine will illuminate
and stop the programme.
C If the dryer is mounted on the washing
machine by means of a bracket, use of
the water drain hose is recommended.
The drain hose should be directed
downwards as shown in the figure.
Adjusting the feet
In order to ensure that your machine
operates more silently and vibration-free, it
must stand level and balanced on its feet.
Balance the machine by adjusting the feet.
Rotate the feet to adjust until the machine
stands level and firmly.
First use
• To have the product ready for operation
before calling the authorised service
agent, make sure that its location
and power supply installations are
appropriate. If they are not, call a
qualified electrician to have any
necessary arrangements carried out.
• Make sure that the power connections
of the product are in accordance
with the instructions given in relevant
chapters of this manual.
7 EN
Disposing of packaging material
Packaging materials are dangerous to
children. Keep packaging materials in
a safe place out of reach of children.
Packaging materials of your product are
manufactured from recyclable materials.
Sort and dispose of them in accordance
with recycled waste instructions. Do not
dispose of them with normal domestic
waste.
Transportation of the machine
1. Unplug the machine from the mains.
2. Remove the water drain (if any) and
chimney connections.
3. Drain water remained in the machine
completely before transportation.
Disposing of the old machine
Dispose of your old machine in an
environmentally friendly manner.
Refer to your local dealer or solid waste
collection centre in your area to learn how
to dispose of your machine.
Before disposing of your old machine,
cut off the power cable plug and make
the loading door lock unusable to avoid
dangerous conditions to children.
Technical specification
EN
2
Height (adjustable)
84.6 cm
Width
59.5 cm
Depth
53 cm
Capacity (max.)
6 kg
Weight (net)
35 kg
Voltage
Rated power input
See type label
Model code
Type label is located behind the loading door.
8 EN
3 Initial preparations for drying
hings to be done for energy
saving:
programme.
• Make sure that you operate the product
at its full capacity but pay attention to
not exceeding it.
• Spin your laundry at the highest speed
possible when washing them. Thus,
the drying time is shortened and energy
consumption is decreased.
• Pay attention to dry same types of
laundry together.
• Follow the instructions in the user
manual for programme selection.
• Make sure that sufficient clearance
is provided at the front and rear side
of the dryer for air circulation. Do not
block the grill at the front side of the
product.
• Do not open the door of the machine
during drying unless necessary. If you
must certainly open the door, pay
attention not to keep it open for a long
time.
• Do not add new (wet) laundry during
drying.
• Lint and fibres released from the
laundry to the air during the drying
cycle are collected in the “Lint Filter”.
Make sure that you clean the filters
before or after each drying.
• In models with condenser, make sure
that you clean the condenser regularly
at least once every month or after every
30 drying cycles.
• In vented models, follow the chimney
connection rules in the user manual
and pay attention to the chimney
cleaning.
• Ventilate the room, where the dryer is
located, well during drying.
• For power saving in models with lamps,
at times when your dryer is not in
use, keep the door closed if the On/
Off button is pressed (if the dryer is
energized).
Laundry suitable for drying in the
machine
C Always follow the suggestions on the
laundry labels. Dry only the laundry
having a label stating that they are
suitable for drying in a dryer and make
sure that you select the appropriate
A B C D
Low
l n m
o p q
Laundry unsuitable for drying in
the machine
• Laundry items with metal attachments
such as belt buckles and metal buttons
can damage your dryer.
• Do not dry items such as woollens, silk
garments and nylon stockings, delicate
embroidered fabrics, laundry with metal
accessories and items such as sleeping
bags in the dryer.
• Laundry made of delicate and valuable
fabrics as well as lace curtains can be
creased. Do not dry them in the dryer!
• Do not dry items made of hermetic
fibres such as pillows and quilts in the
dryer.
• Laundry made of foam or rubber will be
deformed.
• Do not dry laundry containing rubber in
the dryer.
• Do not dry laundry exposed to
petroleum, oil, combustible or explosive
agents in the dryer even if they are
washed beforehand.
• Overly wet laundry or laundry with
dripping water must not be put into the
dryer.
• Items cleaned or washed with gasoil/
fuel oil, dry-laundry solvents and other
combustible or explosive materials as
well as the items that are contaminated
or spotted with such materials should
9 EN
not be dried in the product since they
Correct load capacity
emit flammable or explosive vapor.
• Do not dry items cleaned with industrial
chemicals in the dryer.
• Do not dry your unwashed laundry in the
dryer.
• Items soiled with cooking oils, acetone,
alcohol, fuel oil, kerosene, stain remover,
turpentine, paraffin and paraffin removers
must be washed in hot water with plenty
of detergent before being dried in the
dryer.
• Garments or pillows bolstered with
rubber foam (latex foam), shower
bonnets, water resistant textiles,
materials with rubber reinforcement and
rubber foam pads should not be dried in A Consider the information in the
the dryer.
“Programme Selection Table”. Always
• Do not use fabric softeners and
start the programme in accordance
anti-static products unless they are
with the maximum load capacity.
recommended by the manufacturers of
C Adding laundry to the machine more
the fabric softener or the product.
than the level shown in the figure is not
• Do not dry the underwear reinforced with
recommended. Drying performance
metal parts in the dryer. If these metal
will degrade when the machine is
reinforcements loosen and break during
overloaded. Furthermore, your dryer
drying, they will damage your dryer.
and your laundry can be damaged.
Preparing laundry for drying
C Place your laundry into the drum loosely
• Check all laundry items before loading
so that they will not get tangled.
them into the product to make sure that CLarge pieces (E.g.: bed sheets, quilt
there are no lighters, coins, metal items,
covers, large tablecloths) may bunchneedles and etc. in their pockets or on
up. Stop the dryer 1-2 times during
any part of them.
drying process to separate bunched• Fabric softeners and similar products
up laundry.
must be used in accordance with the
instructions of the manufacturer of the
relevant products.
• All laundry must be spun at the highest
spin speed that your washing machine
allows for the laundry type.
• Laundry may be tangled after washing.
Separate your laundry before placing
them into your dryer.
• Sort your laundry according to their types
and thicknesses. Dry the same type of
laundry together. E.g.: fine kitchen towels
and table cloths dry faster than the thick
bath towels.
10 EN
Following weights are given as examples.
Home articles
Approximate
weights (g)
Cotton quit covers
(double)
Cotton quit covers (single)
Bed sheets (double)
Bed sheets (single)
Large tablecloths
Small tablecloths
Tea napkins
Bath towels
Hand towels
1500
1000
500
350
700
250
100
700
350
Approximate
Garments
weights (g)
Blouses
150
Cotton shirts
300
Shirts
200
Cotton dresses
500
Dresses
350
Jeans
700
Handkerchiefs (10 pieces) 100
T-Shirts
125
Loading the laundry
1. Open the loading door.
2. Place the laundry in the machine
without compressing.
3. Push the loading door to close.
Ensure that no items are caught in the
door.
11 EN
4 Selecting a Programme and Operating Your Machine
Control panel
1
2
3
4
Shirts
Jeans
Express 35
Clean Filter
Drying
Water Tank Full
Iron Dry
Start/
Pause
Delicates
Iron Dry
Freshen Up
Synthetics
Cupboard Dry
Iron Dry
10 min
Cupboard Dry
End/Anticreasing
Buzzer
Cancel
Cupboard Dry
20 min
Cancel
3 sec.
Cotton
On/Off
Cupboard Dry Plus
Timer 40 min
Programmes
Extra Dry
60 min
CD6KG
7
6
6
5
1. Filter cleaning warning light
6. Start/Pause/Cancel button
2. Program follow-up indicator
7. Water tank warning light*
Warning light turns on when the filter is
full.
Used to follow-up the progress of the
current programme.
3. Cancel audio warning
Used to cancel the audio warning given
at the end of the programme.
4. On/Off button
Used to turn on and off the machine.
5. Programme selection knob
Used to start, pause or cancel the
programme.
Warning light turns on when the water
tank is full.
8. Time delay selection button*
Used to set the time delay.
* It may change according to the
specifications of your dryer
Used to select a programme.
12 EN
Preparing the machine
1. Plug in your machine.
2. Place the laundry in the machine.
3. Press the “On/Off” button.
C Pressing the “On/Off” button does not
necessarily mean that the programme
has started. Press “Start/Pause/
Cancel” button of the machine to start
the programme.
Programme selection
Decide the appropriate programme from
the table below which includes drying
temperatures in degrees. Select the
desired programme with the programme
selection button.
Extra dry
Cupboard
dry
Cupboard
dry plus
Iron Dry
C For further program details, see,
“Program Selection Table”
Main programmes
Depending on the type of laundry, the
following main programmes are available:
You can dry your durable laundry with this
programme. Dries at high temperature. It
is recommended to use for your cotton
items (such as bed sheets, quilt cover,
underclothing, etc.).
•Synthetics
You can dry your less durable laundry
•Anti-creasing
A 2-hour anti creasing programme to
prevent laundry from creasing will be
activated if you do not take the laundry
out after the programme is over. This
programme rotates the laundry in
10-minute intervals to prevent creasing.
Special programmes
Dry at high temperature
only for cotton laundry.
Thick and multi layered
laundry (E.g.: towels,
linens, jeans) are dried in
a way that they do not
require ironing before
placing in the wardrobe.
Normal laundry (E.g.:
tablecloths, underwear) are
dried in a way that they do
not require ironing before
placing in the drawers.
Normal laundry (E.g.:
tablecloths, underwear) are
dried in a way that they do
not require ironing before
placing in the drawers,
but more than those in the
ready to wearoption.
Normal laundry (E.g.,
Shirts, dresses) are dried
ready to be ironed.
•Cottons
with this programme. It dries at a lower
temperature compared to the cottons
programme. It is recommended for your
synthetic laundry (such as shirts, blouses,
synthetic/cotton blended laundry, etc.).
C Do not dry curtains and lace in your
machine.
For special cases, there are also extra
programmes available:
C Additional programmes may differ
according to the model of your
machine.
•Express 35
You can use this programme to dry the
cottons that are spun at high speeds in
your washing machine. It can dry your 1,5
kg Cotton laundry (3 Shirts / 3 T-Shirts)
within 35 minutes.
C In order to obtain better results from
the dryer programs, your laundry must
be washed with suitable program and
spun at the recommended spin speeds
in your washing machine.
•Shirts
Dries the shirts in a more sensitive way
so that they are less creased and ironed
easily.
C Shirts may contain little amount of
dampness at the and of the program. It
is advised not to leave the shirts in the
dryer.
•Jeans
You can use this program to dry the jeans
that are spun at high speeds in your
washing machine.
C Review the relevant part of the program
table.
•Delicates
You can dry at a lower temperature your
very delicate laundry (silk blouses, fine
underwear, etc.) that are suitable for
drying or laundry which is advised to be
hand-washed.
C It is recommended to use a cloth bag
to avoid certain delicate garments
and laundry from getting creased
or damaged. Take your garments
immediately out of the dryer and hang
13 EN
them after the programme ends in
order to prevent them being creased.
•Freshen up
Only ventilation is performed for 10
minutes without blowing hot air. You can
air your clothes that have been kept at
closed environments for a long time thanks
to this program to deodorize unpleasant
odors.
•Timer programmes
You can select one of the 10 min., 20 min.,
40 min. and 60 min. timer programmes
to achieve the desired final drying level at
low temperatures. Programme dries at
the selected time regardless of the drying
temperature.
14 EN
Program selection and consumption table
EN
Programs
2
Capacity (kg)
Spin speed in
washing machine
(rpm)
Approximate
amount of
remaining
humidity
Drying time
(minutes)
Cottons / Coloreds
A
Cupboard dry
6
1000
% 60
106
A
Cupboard dry plus
6
1000
% 60
110
A
Iron dry
6
1000
% 60
90
Express 35
1.5
1200
% 50
35
Shirts
1.5
1200
% 50
40
Jeans
3
1200
% 50
80
1.5
600
% 40
40
3
800
% 40
45
Delicates
Synthetics
B
Cupboard dry
Energy consumption values
Programs
Cotton-Extra Dry*
Capacity (kg)
Energy consumption value kWh per
year
Energy rating
star
6
-
-
* : Energy Label standard program (AS/NZS 2442)
All values given in the table have been fixed according to standard laboratory conditions.
These values may deviate from the table according to the laundry type, laundry spin
speed, environmental conditions and voltage fluctuations.
15 EN
Auxiliary function
illuminated until the next step.
Your dryer will give an audio warning when
the programme comes to an end. If you
do not want to hear the audio warning,
press “Cancel Audio Warning” button. The
relevant light will turn on when this button
is pressed and an audio warning will not
be given when the programme comes to
an end.
CYou can select this function either before
or after the programme starts.
- Illuminates when the program comes
to an end and anti-creasing function is
activated.
C If more than one LED light up or
flash concurrently, it means there is
malfunctioning or a failure (please see,
Solution suggestions for problems).
Cancel audio warning
Warning indicators
CWarning indicators may differ according
to the model of your dryer.
Filter cleaning
A warning light will turn on to remind filter
cleaning after the programme finishes.
CIf the filter cleaning warning light lights
up continuously, please refer to,
“Suggested solutions for problems”.
Water tank
Warning light starts flashing when the
tank is filled with water. The dryer stops
operating if the warning light turns on
when a programme is running. Drain the
water in the water tank to restart the dryer.
Press “Start/Pause/Cancel” button to start
the programme after you have emptied the
water tank. The warning light turns off and
the programme resumes operating.
Starting the programme
1. Press “Start/Pause/Cancel” button to
start the programme.
2. Light of the “Start/Pause/Cancel”
button will turn on to indicate that the
programme has started.
Progress of program
Progress of a running program is shown
through the program follow-up indicator.
At the beginning of every program step,
the relevant indicator LED will light up and
light of the completed step will turn off.
“Drying”:
- Drying level will be illuminated during
the whole drying process until the drying
degree reaches “iron dry”.
“Iron Dry”:
- Starts to illuminate when the drying
degree reaches “iron dry” step and
remains illuminated until the next step.
“Ready to wear”:
Starts to illuminate when the drying degree
reaches “Ready to wear” step and remains
“Final / Anti-creasing”:
Changing the programme after it has
started
You can use this feature to dry
your clothes under higher or lower
temperatures after your dryer has started.
For example;
1. Press and hold the “Start/Pause/
Cancel” button for about 3 seconds
to “Cancel” the programme in order to
select “Extra Dry” programme instead
of “Iron Dry” programme.
2. Select the “Extra Dry” programme
by rotating the programme selection
button.
3. Press “Start/Pause/Cancel” button to
start the programme.
CPress “Start/Pause/Cancel” button for
3 seconds to cancel the programme
or turn the programme selection knob
in any direction to end the programme
while the machine is running. Water
tank and filter cleaning warning lights
turn on to warn the user when the
programme is cancelled by pressing
the “Start/Pause/Cancel” button for 3
seconds. However, the warning lights
do not turn on when the programme
is cancelled by turning the programme
selection knob. Only the drying light
turns on and the machine remains in
hold until a new programme is selected
and the “Start/Pause/Cancel” button
is pressed. Child-proof lock of the
machine should not be active in order
to perform these two operations. If the
child-proof lock is active, deactivate it
before performing these operations.
Adding/removing laundry in standby
mode
In order to add or remove laundry after the
programme starts:
1. Press the “Start/Pause/Cancel” button
to switch the dryer to “Pause” mode.
Drying process will stop.
2. Open the door at “Pause” position and
close it again after adding or taking out
16 EN
laundry.
3. Press “Start/Pause/Cancel” button to
start the programme.
CAny laundry added after the drying
process has started may cause the
dried clothes in the machine intermingle
with wet clothes and the result will be
wet laundry after the drying process is
over.
CLaundry may be added or taken out
as much as desired during a drying
process, but this process will extend
the programme duration and increase
energy consumption since the drying
will be interrupted continuously.
Therefore, it is recommended to add
laundry before the drying programme
has started.
lock is active. Press the buttons for 3
seconds to deactivate the child-proof
lock. Single beep will be heard and
child-proof lock will be deactivated.
A A double beep will be heard if you turn
the programme selection knob when
the machine is running and the childproof lock is active. If you deactivate
the child-proof lock without returning
the program selection knob to its
previous position, the programme will
be terminated since the position of the
programme selection knob is changed.
The drying light turns on and the
machine remains on hold until a new
programme is selected and the “Start/
Pause/Cancel” button is pressed.
There is a child-proof lock to prevent
any programme interruption due to the
pressing of button while the programme is
running. The loading door and all buttons
except the “On/Off” button on the control
panel are deactivated when the child-proof
lock is active.
Press the “Start/Pause/Cancel” and
“Cancel audio warning” buttons
simultaneously for 3 seconds to activate
the child-press lock.
To start a new programme after the
programme is over or to interrupt the
programme, the child-proof lock should be
deactivated. Press the same buttons for
3 sec. again to deactivate the child-proof
lock.
CChild-proof lock is deactivated when the
machine is restarted by pressing the
On/Off button.
To cancel any selected programme:
Press “Start/Pause/Cancel” button for
about 3 seconds. The “Filter cleaning”,
“Water tank” and “End/ Anti-creasing”
warning lights will turn on at the end of this
period for reminding purposes.
A As the inside of the dryer will be
excessively hot when you cancel the
programme while the dryer is running,
activate the ventilation programme to
cool it down.
Child-proof lock
C Press the relevant buttons for 3
seconds to activate the child-proof
lock. A long beep will be heard and
the child-proof lock will be activated. A
double beep will be heard if you press
any button or turn the programme
selection knob while the child-proof
Finishing by canceling the
programme
End of programme
The “End/Anti-creasing”, “Filter cleaning”
and “Water tank” warning lights on the
programme follow up indicator will turn on
when the programme comes to an end.
The door can be opened and the machine
becomes ready for a second cycle.
Press “On/Off” button to turn off the dryer.
CFinal step of the drying cycle (cooling
step) is performed without heat
application in order to keep the items
at a temperature that would not harm
them.
CA 2-hour anti creasing programme to
prevent laundry from creasing will be
activated if you do not take the laundry
out after the programme has come to
an end.
CIf you will not take the laundry out
immediately, do not stop the dryer
before the drying process is complete.
CClean the filter after each drying (please
see, Filter cleaning).
CDrain the water tank after each drying
(please see, Water tank)
17 EN
5 Maintenance and cleaning
Filter Cartridge / Door Inner
Surface
Lint and fibres released from the laundry to
the air during the drying cycle are collected
in the “Filter Cartridge”.
Sensor
C Such fibre and lint are generally formed
during wearing and washing.
C Always clean the filter and the inner
surfaces of the cover after each drying
process.
C You can clean the filter and filter area by
vacuum cleaner.
To clean the filter:
1. Open the loading door.
2. Remove the cover filter by pulling it up
and open the filter.
3. Clean lint, fibre, and cotton raveling by
hand or with a soft piece of cloth.
4. Close the filter and place it back into its
seat.
C Clogging may arise on the filter surface
after using your machine for some time;
if this occurs, wash the filter with water
and dry it before using again.
There are humidity sensors in your dryer
that detect whether the laundry is dry or
not.
To clean the sensor:
1. Open the loading door of the dryer.
2. Allow the machine to cool down if
drying has been carried out.
3. Wipe the metal sensors with a soft
cloth, dampened with vinegar and dry
them.
CClean metal sensors 4 times a year.
ANever use solvents, cleaning agents
or similar substances when cleaning
since these materials can cause fire and
explosion!
Water tank;
C Clean the entire inner surface of the
cover and door gasket.
The moisture in the damp laundry is taken
from the laundry and condens ed. Drain
the water tank after each drying cycle or
during drying when “Water tank” warning
light turns on.
18 EN
ACondensed water is not drinkable!
ANever take out the water tank when the
programme is running!
- Inside the drawer on the panel
- Behind the kick plate cover
If you forget to drain the water tank, your
dryer will stop during the following drying
cycles when the water tank is full and the
“Water tank” warning light will turn on. If
this is the case, press the “Start/Pause/
Cancel” button to resume the drying cycle
after draining the water tank.
To drain the water tank:
1-Carefully remove the water tank by
opening the kick plate cover/pulling the
drawer.
4-Place the water tank into its seat.
For the condenser;
Hot and humid air in the condenser is
cooled with the cold air from the room.
Thus, the humid air circulating in your
dryer is condensed and then pumped into
the tank.
CClean the condenser after every 30
drying cycles or once a month.
To clean the condenser:
1. If a drying process has been carried out,
open the door of the machine and wait
until it cools down.
2. Unlock the 2 condenser locks after
opening the kick plate.
2-Drain the water in the tank
3. Pull out the condenser.
3-If there is lint accumulation in the funnel
of the water tank, clean it under running
water.
19 EN
4. Clean the condenser by applying
pressurized water with a shower
armature and wait until the water
drains.
5. Place the condenser in its housing.
Fasten the 2 locks and make sure that
they are seated securely.
6. Close the kick plate cover.
20 EN
6 Suggested solutions for problems
Drying process takes too much time
• Meshes of the filter may be clogged. Wash with water.
Laundry comes out wet at the end of drying.
• Meshes of the filter may be clogged. Wash with water.
• Excessive laundry might have been loaded in. Do not load the dryer in excess.
Dryer does not switch on or the programme does not start. Dryer is not activated
when set.
• It might have not been plugged in. Make sure that the machine is plugged in.
• The loading door may be ajar. Make sure that the loading door is properly closed.
• Programme might have not been set or the "Start/Pause/Cancel" button might
have not been pressed. Make sure that the programme has been set and it is not
in “Pause” mode.
• "Childproof lock" might have been activated. Deactivate the childproof lock.
Programme has been interrupted without any cause.
• The loading door may be ajar. Make sure that the loading door is properly closed.
• Electricity may be cut off. Press "Start/Pause/Cancel" button to start the
programme.
Laundry has shrunk, become felted or deteriorated.
• A programme suitable for the laundry type might have not been used. Dry only
the laundry which is suitable for drying in dryer after checking the labels on your
clothes.
• Select a programme with suitable low temperature for the laundry type to dry your
clothes.
Drum lightning does not come on.
• Dryer might have not been started by using the "On/Off" button. Make sure that
the dryer is on.
• Bulb may have blown. Call the authorized service to replace the bulb.
“Final / Anti-creasing” symbol flashes.
• The 2-hour anti creasing programme to prevent laundry from creasing might have
been activated. Turn off the dryer and take out the laundry.
“Final / Anti-creasing” symbol is on.
• Programme has come to an end. Turn off the dryer and take out the laundry.
Water comes out the cover.
• Clean the entire inner surface of the cover and door gasket.
Cover opens spontaneously.
• Push it until you hear that it is closed.
For products with a condenser:
“Water tank” warning symbol is on.
• Water may be full.
• Anti-creasing programme might be running. Drain the water in the tank.
“Filter cleaning” symbol is on.
• Filter might have not been cleaned. Clean the cover filter.
21 EN
“Condenser cleaning” symbol is on.
• Filter drawer/Condenser might have not been cleaned. Clean the filters in the
condenser/filter drawer under the kick plate.
A Call an authorised service if the problem persists.
22 EN