Arecont Vision D4SO Outdoor Dome Series Installation Manual

Arecont Vision D4SO Outdoor Dome Series Installation Manual
0|P a g e
Arecont Vision D4SO Outdoor Dome Series Installation Manual
D4SO Outdoor Dome Installation Manual
Inside the box:
A.
B.
C.
D.
E.
F.
G.
1.
Arecont Vision D4SO Dome Camera
Mounting template
Security L-key
One double sided hex key
One single sided hex key
6-position external power & IO plug
Pack of four (4) wood screws and four (4)
dry wall anchors
3.
Not included but needed:
•
•
•
#1 Phillips head screw driver
#2 Phillips head screw driver
Small Flat Head screw driver
A
C
2.
Remove camera and hardware from the
box.
Using the Mounting Template, prepare
the mounting provisions for camera
installation. NOTE: the 19.5mm diameter
hole on the Mounting template is where
the Ethernet cable will be exiting the
D4SO, align accordingly. If using the
side conduit hole, please see step 7
below.
Using Security L-key, loosen the four (4)
screws securing the dome cover (Image
2). Remove vandal resistant dome
cover. NOTE: Do not remove screws
from the dome cover.
B
D
E
F
G
Image 2
Image 1
Mounting the Camera:
1|P a g e
Arecont Vision D4SO Outdoor Dome Series Installation Manual
4.
Run Ethernet cable through the hole on the
bottom of D4SO and plug it into the RJ45 port
®
on Arecont Vision’s compact MegaVideo
camera. (Image 3) . NOTE: If the camera will
be powered via PoE, please skip to step 5.
Image 4-1
Image 3
5.
If the camera is powered by an outside power
supply, run power wires through the hole and
connect power wires to appropriate contacts
of 6-postion connector using small flat screw
driver and connect 6-position plug to camera
as shown in Image 4-1.
Note: Please make sure the polarity of the
AC/DC input on the camera match the way
wires are installed in connector shown in
Image 4-2.
Image 4-2
6.
Align the holes in the camera with the
prepared holes on the mounting surface.
Attach the camera to the mounting surface
with the wood screws or any optional
hardware suitable for the mounting surface.
2|P a g e
Arecont Vision D4SO Outdoor Dome Series Installation Manual
7.
If you are using the side conduit opening,
remove the conduit plug by first removing the
socket set screw using one of provided Allen
keys (Image 5).
9.
Adjust lens tilt as required and tighten the
screw. CAUTION: To properly install camera,
the U bracket needs to be installed between
the dome BASE and camera Bubble shown
in Image 7
U Bracket
Gimbal Base
Image 5
Adjusting the Tilt and Pan:
8.
To adjust the tilt, use a #1 Phillips screwdriver
to loosen the screw on the side of the U
bracket 1/4 turn (Image 6). CAUTION: Do not
remove the screw!
Image 7
10.
To adjust the pan, hold and turn the U bracket
as shown in Image 8.
90°
Pan=360°
0°
Screw
Image 6
Image 8
3|P a g e
Arecont Vision D4SO Outdoor Dome Series Installation Manual
Adjusting the Focus:
11.
B
To focus the lens, loosen the three set screws
as shown in Image 9 and adjust each as
needed. A adjusts the zoom, B adjusts the
iris, C adjusts the focus.
Note: Adjust zoom first then focus!
A
C
Note: For more information on proper
focusing technique, please watch the
“Focusing Arecont Vision Megapixel
Cameras” Best Practices Training Video at
www.youtube.com/ArecontVision.
Image 9
12.
Secure the dome cover to the camera.
13.
Tighten the set screw on the dome cover.
14.
Rotate bubble to align camera with slot in
camera shield.
15.
Remove the protective film from the camera
dome. NOTE: be cautious not to scratch the
vandal dome cover.
4|P a g e
Arecont Vision D4SO Outdoor Dome Series Installation Manual
D4SO Pendant Mount (MD-CMT) Installation Instructions
Inside the box:
A.
B.
C.
D.
E.
F.
Top shield
Pendant Mount
Mounting template
Pack of four (4) machine screws
Pack of four (4) small machine screws
Pack of four (4) wood screws and four (4)
dry wall anchors
G. Large round rubber gasket
H. Smaller square rubber gasket
I. One double sided hex key
Not included but needed:
•
D
F
I
B
H
Image 12
2.
Using the Mounting template, prepare the
mounting provisions for camera installation.
3.
Place small gasket onto pendant dome as
shown in image 11.
4.
Attach Dome to Pendant as shown in Image
12 using four machine screws provided.
5.
Install large round rubber gasket onto
Pendant as shown in image 12. Be sure to
align the holes appropriately.
6.
Run Ethernet Cable and outside power cable
(if necessary) through the Pendant.
7.
Attach Pendant to the ceiling using the four
wood screws provided or any optional
hardware suitable for the mounting surface.
8.
For installation of the camera, please
reference “Mounting the Camera”.
#2 Phillips head screw driver
E
A
Image 11
G
C
Image 10
1.
Remove Pendant Mount and hardware from
the box.
5|P a g e
Arecont Vision D4SO Outdoor Dome Series Installation Manual
D4SO Wall Mount (MD-WMT2) Installation Instructions
Caution:
1.
Remove Wall Mount and hardware from the
box.
MD-WMT2 only fits with SV-JBA and SV-EBA but
not with MD-JBA and MD-EBA!
Inside the box:
A.
B.
C.
D.
E.
F.
Wall mount ( Fit 1.5 NPT Standard)
Top shield
Mounting template
One double sided hex key
Pack of four (4) machine screws
Pack of four (4) wood screws and four (4)
dry wall anchors
Not included but needed:
•
Image 14
#2 Phillips head screw driver
B
A
C
D
Image 13
E
2.
Using the Mounting template, prepare the
mounting surface.
3.
Install Top Shield on Wall Mount as shown in
image 14.
4.
Fasten the socket set screw using double side
hex key.
5.
Run Ethernet Cable and outside power cable
(if necessary) through the Wall Mount.
6.
Attach Wall Mount to the wall using drywall
screws or any optional hardware suitable for
the mounting surface.
7.
For installation of the camera, please
reference “Mounting the Camera”.
F
6|P a g e
Arecont Vision D4SO Outdoor Dome Series Installation Manual
D4SO Wall Mount Cap (MD-CAP) Installation Instructions
Inside the box:
A.
B.
Wall Mount Cap (MD-CAP)
Pack of four (4) machine screws
MD-CAP
Not included but needed:
•
•
•
•
1½” NPT Pipe
1½” NPT Coupling
1½” NPT Flange
#2 Phillips head screw driver
1 ½” Coupling
1 ½” Pipe
1 ½” Flange
A
B
Image 16
3.
Run Ethernet Cable and outside power cable
(if necessary) through the Pendant.
Image 15
1.
Remove Wall Mount Cap from the box.
4.
2.
Assemble Wall Mount Cap, 1½” Coupling,
1½” Pipe nipple and 1½” Flange as a Pendant
Mount shown in image 16.
Attach Pendant to the ceiling using four wood
screws or any optional hardware suitable for
the mounting surface
5.
For installation of the camera, please
reference “Mounting the Camera”.
7|P a g e
Arecont Vision D4SO Outdoor Dome Series Installation Manual
D4SO Junction Box Adapter (MD-JBA) Installation Instruction
Caution:
1.
Remove Junction Box and hardware from the
box
MD-JBA only fits with D4SO and MD-CMT but not
with MD-WMT2!
Inside the box:
A.
B.
C.
D.
E.
Junction Box Adapter
Large round rubber gasket
Pack of four (4) wood screws and four (4)
dry wall anchors
Pack of four (4) machine screws
One double sided hex key
Image 18
Not included but needed:
•
•
•
2.
#2 Phillips head screw driver
D4SO Wall Mount, MD-WMT
¾” NPT Conduit (if necessary)
B
A
5.
D
Remove the conduit plug by first removing the
socket set screw using one of provided Allen
keys shown in Image 18.
3. Attach Junction Box Adapter to the wall using
drywall screws or any optional hardware
suitable for the mounting surface.
4.
C
Image 19
E
Attach D4SO Wall Mount to Junction Box
Adapter as shown in Image 19.
Connect ¾” NPT Conduit to Junction Box
Adapter
6. Run Ethernet Cable and outside power cable (if
necessary) through the Junction Box Adapter
and Wall Mount.
7.
For installation of the camera, please
reference “Mounting the Camera”.
Image 17
8|P a g e
Arecont Vision D4SO Outdoor Dome Series Installation Manual
D4SO Junction Box Adapter (SV-JBA) for MD-WMT2 Installation Instruction
Caution:
SV-JBA only fits with MD-WMT2 but not with D4SO
and MD-CMT!
Inside the box:
A.
B.
C.
D.
E.
Junction Box Adapter
Pack of four (4) machine screws
One double sided hex key
Pack of four (4) wood screws and four (4)
dry wall anchors
Large round rubber gasket
Image 21
2.
Not included but needed:
•
•
•
#2 Phillips head screw driver
D4SO Wall Mount, MD-WMT
¾” NPT Conduit (if necessary)
A
B
C
D
3. Attach Junction Box Adapter to the wall using
drywall screws or any optional hardware
suitable for the mounting surface.
E
4.
5.
Image 20
1.
Remove the conduit plug by first removing the
socket set screw using one of provided Allen
keys.
Remove Junction Box and hardware from the
box
Attach D4SO Wall Mount to Junction Box
Adapter as shown in Image 21.
Connect ¾” NPT Conduit to Junction Box
Adapter.
6. Run Ethernet Cable and outside power cable (if
necessary) through the Junction Box Adapter
and Wall Mount.
7.
For installation of the camera, please
reference “Mounting the Camera”.
9|P a g e
Arecont Vision D4SO Outdoor Dome Series Installation Manual
D4SO Flush Mount Adapter (MD-FMA) Installation Instructions
Inside the box:
A.
B.
C.
D.
5.
White Trim Ring
Flush Mount Adapter
Mounting template
Pack of four (4) machine screws and one
(1) I-Blot
Screw the “lever screws” until the FMA is
snuggly installed, as shown in Image 23. The
“Support Arm” will ride down the screw to
compress the mounting surface. NOTE: Do
not over-torque the lever screws
6. Attach the Trim Ring to the Flush Mount Adapter
by rotating clockwise as show in Image 24.
Not included but needed:
•
A
Support
Arm
#2 Phillips head screw driver
B
C
D
Lever
screw
Image 23
Image 22
1.
Remove Flush Mount Adapter, Trim Ring and
hardware from the box.
2.
Attach Dome to Flush Mount Adapter as
shown in Image 23. Please reference
“Mounting the Camera”, if needed.
3.
Using the Mounting template, cut a hole in
surface for mounting.
4. Insert Flush Mount Adapter into the hole.
Image 24
10 | P a g e
Arecont Vision D4SO Outdoor Dome Series Installation Manual
D4SO Electrical Box Adapter (MD-EBA) Installation Instructions
Caution:
3.
Attach Electrical Box Adapter to Electrical Box
as shown in Image 26.
MD-EBA fits with D4SO and MD-CMT but not with
MD-WMT2!
4.
Attach Dome to Electrical Box Adapter as
shown in Image 27. Please reference
“Mounting the Camera”, if needed.
Inside the box:
A.
B.
Electrical Box Adapter
Pack of four (4) machine screws
Not included but needed:
•
•
#2 Phillips head screw driver
Common Electrical Box, such as single
gang box, double gang box or square
electrical box.
Image 26
B
A
Image 25
1.
Remove Electrical Box Adapter and hardware
from the box.
2.
Match mounting holes on adapter with thread
holes on the electrical box, make sure every
threaded hole is matched with mounting hole.
Image 27
11 | P a g e
Arecont Vision D4SO Outdoor Dome Series Installation Manual
D4SO Electrical Box Adapter (SV-EBA) for SV-WMT2 Installation Instructions
Caution:
3.
Attach Electrical Box Adapter to Electrical Box.
SV-EBA fits with MD-WMT2 but not with D4SO and
MD-CMT!
4.
Attach Dome to Electrical Box Adapter as
shown in Image 29. Please reference
“Mounting the Camera”, if needed.
Inside the box:
A.
B.
Electrical Box Adapter
Pack of four (4) machine screws
Not included but needed:
•
•
#2 Phillips head screw driver
Common Electrical Box, such as single
gang box, double gang box or square
electrical box.
A
B
Image 29
Image 28
1.
Remove Electrical Box Adapter and hardware
from the box.
2.
Match mounting holes on adapter with thread
holes on the electrical box, make sure every
threaded hole is matched with mounting hole.
12 | P a g e
Arecont Vision D4SO Outdoor Dome Series Installation Manual
D4SO Pole Mount Adapter (MD-PMA) Installation Instructions
Inside the box:
A.
B.
C.
D.
E.
Pole Mount Adapter
2x Compress Fittings
2x Small Steel Straps
2x Large Steel Straps
Pack of four (4) machine screws
4.
Run Ethernet Cable and outside power cable
(if necessary) through the Compress Fittings
and D4SO Wall Mount.
5.
Use the supplied two Steel Straps to attach
the Pole Mount Adapter to the pole and
tighten the compression screws as shown in
Image 32.
6.
Attach Dome to Wall Mount Adapter. Please
reference “Mounting the Camera”, if needed.
7.
Tighten the Compress Fittings to seal the
wiring holes.
Not included but needed:
•
•
#2 Phillips head screw driver
D4SO Wall Mount Adapter
D
C
E
A
B
Image 30
1.
Remove Pole Mount Adapter, Compress
Fittings, Steel Straps and hardware from the
box.
2.
Install Compress Fittings to Pole Mount
Adapter as shown in Image 31.
3.
Attach D4SO Wall Mount Adapter to Pole
Mount Adapter as shown in Image 32.
Image 31
Wall
Mount
Adapter
Compression
Screws
Image 32
13 | P a g e
Arecont Vision D4SO Outdoor Dome Series Installation Manual
D4SO Corner Mount Adapter (MD-CRMA) Installation Instructions
Inside the box:
A.
B.
C.
D.
Corner Mount Adapter
2x Compression Fittings
Pack of four (4) machine screws
2x Packs of four (4) wood screws and four
(4) dry wall anchors
Not included but needed:
•
•
Image 34
#2 Phillips head screw driver
D4SO Wall Mount Adapter
B
C
D
A
Image 35
4.
Run Ethernet Cable and outside power cable
(if necessary) through the Compress Fittings
and D4SO Wall Mount.
5.
Using the screws provided (or other hardware)
attach the Corner Mount Adapter to an
exterior 90° corner wall.
Image 33
1.
Remove Corner Mount Adapter, Compress
Fitting and hardware from the box.
2.
Install Compress Fittings to Corner Mount
Adapter as shown in Image 34.
6.
Attach Dome to Wall Mount Adapter. Please
reference “Mounting the Camera”, if needed.
3.
Attach Wall Mount Adapter to Corner Mount
Adapter as shown in Image 35.
7.
Tighten the Compress Fittings to seal the
wiring holes.
14 | P a g e
Arecont Vision D4SO Outdoor Dome Series Installation Manual
D4SO I/O Cable Connection
Not included but needed:
•
2.
Flat head screw driver
Input
Output
Image 36
1.
To use the I/O ports of the D4SO, insert the
connector to Arecont Vision Compact camera
and locate the “I/O” parts as shown in Image
37. NOTE: There are six connectors that look
identical, be sure to use correct I/O ports
shown in Image 36.
Run the I/O cable through the hole in the
bottom of the camera and plug it into the “J7”
connector as shown in image 33. NOTE: The
connection is a little stiff so be sure to apply
enough pressure to connect it; using a flat
head screw driver to push it in is
recommended.
Electrical Characteristics:
Input voltage (V)
(measured between + and –
terminals)
Output current (mA)
(measured between + and – terminals)
Applied Voltage Rage: 0 - 80V
ON
Min
2.9
Max
6.3
OFF
0
1.3
ON
-
50
OFF
-
0.1
Table 1
NOTE: Both the input and the output are electrically
isolated from the rest of the camera’s
electrical circuitry via general-purpose photo
couplers. The input is additionally protected
with a serial 250 Ohm resistor, and a
debouncing circuit. Duration of any input
signal should be at least 5 ms to comply with
the requirements of the debouncing circuit.
Orange
Yellow
White
Black
OUT +
OUT –
IN +
IN -
Table 2
Image 37
15 | P a g e
Arecont Vision D4SO Outdoor Dome Series Installation Manual
D4SO Heater (MD-1HK) Accessory
Inside the box:
A.
B.
4.
Heater
Two (2) screws
Screw the heater board to the standoffs as
shown in Image 40.
Not included but needed:
•
#1 Phillips head screw driver
A
B
Image 39
Image 38
1.
Run the heater cable out of the hole in the
bottom of the camera and connect it to 1050VDC power supply. 10 Watts max. Red is
positive (+) cable.
2.
Remove the heater kit from the box.
3.
With the heater element protruding out of the
camera, align the two (2) holes on the heater
board with the two standoffs shown in Image
39.
Image 40
16 | P a g e
Arecont Vision D4SO Outdoor Dome Series Installation Manual
17 | P a g e