Windsor chariot iSCRUB CSXE24 10060290 Operating instructions

iSCRUB
Operating Instructions (ENG)
MODELS: CS24
10060210
CSE24
10060250
CS24SP
10060220
CSX24
10060270
CSXE24
10060290
CSE24SP
10060260
CSXEO24
10060300
Read these instructions before using the machine
DT
86037660 10/20/11
MACHINE DATA LOG/OVERVIEW
MODEL _______________________________________
DATE OF PURCHASE __________________________
SERIAL NUMBER ______________________________
SALES REPRESENTATIVE # _____________________
YOUR DEALER
Name: __________________________________________________________________________________________________
Address: _______________________________________________________________________________________________
Phone Number: _________________________________________________________________________________________
OVERVIEW
The Chariot Scrubber is a battery powered, stand-on, hard floor scrubber intended for commercial
use. The appliance applies a cleaning solution onto a hard floor, scrubs the floor with brushes or
pads, and then vacuums the soiled water back into the recovery tank.
2
86037660 CHARIOT 11/09/06
TABLE OF CONTENTS
Machine Data Log/Overview. ...............................2
Table Of Contents ................................................3
HOW TO USE THIS MANUAL
How To Use This Manual.....................................1-1
SAFETY
Important Safety Instructions ............................ 2-1
Hazard Intensity Level....................................... 2-2
Safety Label Location........................................ 2-3
OPERATIONS
Technical Specifications.................................... 3-1
How The Machine Works. ................................. 3-3
Components ...................................................... 3-4
Drive Controls.................................................... 3-5
Scrub Controls-Basic & Cylindrical ................... 3-9
Scrub Controls-Deluxe ...................................... 3-11
Scrub Controls-Squeegee................................. 3-13
Machine Operation ............................................ 3-15
Pre-Run Machine Inspection ........................ 3-15
Starting Machine .......................................... 3-15
Emergency Stop Procedures ....................... 3-15
Filling Solution Tank ..................................... 3-16
Normal Scrubbing......................................... 3-16
To Begin Scrubbing...................................... 3-17
Priming Pump ............................................... 3-17
To Stop Scrubbing........................................ 3-18
Double Scrub................................................ 3-18
Emptying And Cleaning Tanks ..................... 3-19
MAINTENANCE
Service Schedule .............................................. 4-1
Batteries. ........................................................... 4-2
Squeegee. ......................................................... 4-6
Scrub Brushes................................................... 4-9
Scrub Deck-Disk................................................ 4-10
Scrub Deck-Cylindrical ...................................... 4-13
Circuit Protection ............................................... 4-18
Solution Strainer & Pump-Disk.......................... 4-19
Solution Strainer & Pump-Cylindrical ................ 4-20
Vacuum & Float Shut-Off .................................. 4-22
Drive Motor & Brake .......................................... 4-24
Bag Replacement.............................................. 4-27
Transporting Machine........................................ 4-28
Machine Troubleshooting.................................. 4-29
GROUP PARTS LIST
Bumper ..............................................................5-1
Control Panel-Basic-Cylindrical .........................5-3
Control Panel-Deluxe ........................................5-5
Control Panel Housing.......................................5-7
Decal..................................................................5-9
Frame-Lower .....................................................5-11
Frame-Upper .....................................................5-13
Pedal Platform ...................................................5-15
Rear Cover ........................................................5-19
Scrub Brush/Pad Driver.....................................5-21
Scrub Deck - Disk..............................................5-23
Scrub Deck – Cylindrical ...................................5-25
Scrub Deck Aqua-Mizer™ .................................5-27
Side Squeegee – Cylindrical .............................5-29
Scrub deck – Side Squeegee – Cylindrical .......5-31
Scrub Deck Skirts ..............................................5-33
Scrub Deck Lift ..................................................5-35
Scrub Deck Mounting- Cylindrical .....................5-37
Scrub Deck Actuator – Cylindrical.....................5-39
Solution Cylindrical ............................................5-41
Solution Disk......................................................5-43
Squeegee - Disk ................................................5-45
Squeegee – Cylindrical......................................5-47
Squeegee Lift-Basic ..........................................5-49
Squeegee Lift-Deluxe ........................................5-51
Squeegee Swing ...............................................5-53
Squeegee Lift – Cylindrical................................5-55
Steering .............................................................5-59
Tank...................................................................5-61
Vacuum..............................................................5-63
Wheel-Front Drive, Chain ..................................5-65
Wheel-Front Drive, Gear ...................................5-67
Wheel-Front Brake ............................................5-69
Wheel-Rear........................................................5-71
Wiring-Batteries .................................................5-73
Wiring-Components...........................................5-75
Wiring-Control Panel-Basic-Cylindrical .............5-77
Wiring-Control Panel-Deluxe .............................5-79
Wiring-Drive Motor.............................................5-81
Wiring-Main Harness .........................................5-83
Wiring-Pedal Platform........................................5-85
Wiring Diagram-Basic-Cylindrical ......................5-87
Wiring-Diagram-Deluxe .....................................5-88
Hose Diagram-Disk ...........................................5-89
Hose Diagram-Cylindrical..................................5-90
Suggested Spare Parts .....................................5-91
OPTIONS
Back-Up Alarm – Option....................................6-1
Battery Cart – Option.........................................6-3
Seat – Option.....................................................6-7
Warning Light – Option......................................6-9
EC Declaration of Conformity ............................6-11
Serial Numbers..................................................6-14
Warranty
86037660 CHARIOT 04/15/08
3
HOW TO USE THIS MANUAL
This manual contains the following sections:
-
HOW TO USE THIS MANUAL
SAFETY
OPERATIONS
MAINTENANCE
PARTS LIST
The HOW TO USE THIS MANUAL section will tell
you how to find important information for ordering
correct repair parts.
Parts may be ordered from authorized Windsor
dealers. When placing an order for parts, the
machine model and machine serial number are
important. Refer to the MACHINE DATA box which
is filled out during the installation of your machine.
The MACHINE DATA box is located on the inside of
the front cover of this manual.
MODEL _____________________________________
DATE OF PURCHASE ________________________
The SAFETY section contains important information
regarding hazard or unsafe practices of the
machine. Levels of hazards are identified that could
result in product or personal injury, or severe injury
resulting in death.
The OPERATIONS section is to familiarize the
operator with the operation and function of the
machine.
The MAINTENANCE section contains preventive
maintenance to keep the machine and its
components in good working condition. They are
listed in this general order:
-
Batteries
Scrub Brushes
Adjusting Squeegee
Service Schedule
Machine Troubleshooting
The PARTS LIST section contains assembled parts
illustrations and corresponding parts list. The parts
lists include a number of columns of information:
SERIAL NUMBER ____________________________
SALES REPRESENTATIVE # ___________________
-
The model and serial number of your machine are
located below the battery compartment of the
machine.
-
-
REF – column refers to the reference
number on the parts illustration.
PART NO. – column lists the part
number for the part.
PRV NO. - Reference No.
QTY – column lists the quantity of the
part used in that area of the machine.
DESCRIPTION – column is a brief
description of the part.
SERIAL NO. FROM – If this column has
an (*) and a Reference number, see the
SERIAL NUMBERS page in the back of
your manual. If column has two asterisk
(**), call manufacturer for serial number.
The serial number indicates the first
machine the part number is applicable
to. The main illustration shows the most
current design of the machine. When a
boxed illustration is shown, it displays
the older design.
NOTES – column for information not
noted by the other columns.
NOTE: If a service or option kit is installed on your
machine, be sure to keep the KIT INSTRUCTIONS
which came with the kit. It contains replacement
parts numbers needed for ordering future parts.
NOTE: The number on the lower left corner of the
front cover is the part number for this manual.
1-1
86037660 CHARIOT 04/15/08
IMPORTANT SAFETY INSTRUCTIONS
When using an battery powered appliance, basic precaution
must always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.
To reduce the risk of fire, electric shock, or injury:
Use only indoors. Do not use outdoors or expose to rain.
Use only as described in this manual. Use only manufacturer’s recommended components and attachments.
If the machine is not working properly, has been dropped, damaged, left outdoors, or dropped into water, return
it to an authorized service center.
Do not operate the machine with any openings blocked. Keep openings free of debris that may reduce airflow.
This machine is not suitable for picking up hazardous dust.
Machine can cause a fire when operating near flammable vapors or materials. Do not operate this machine near
flammable fluids, dust or vapors.
This machine is suitable for commercial use, for example in hotels, schools, hospitals, factories, shops
and offices for more than normal housekeeping purposes.
Maintenance and repairs must be done by qualified personnel.
If foam or liquid comes out of machine, switch off immediately.
Disconnect battery before cleaning or servicing.
Before the machine is discarded, the batteries must be removed and properly disposed of.
Make sure all warning and caution labels are legible and properly attached to the machine.
During operation, attention shall be paid to other persons, especially children.
Before use all covers and doors shall be put in the positions specified in the instructions.
When leaving unattended, secure against unintentional movement.
The machine shall only be operated by instructed and authorized persons.
When leaving unattended, switch off or lock the main power switch to prevent unauthorized use.
Only chemicals recommended by the manufacturer shall be used.
This appliance has been designed for use with the brushes specified by the manufacturer. The fitting of other
brushes may affect its safety.
Do not use on surfaces having a gradient of over 10% (6 degrees).
SAVE THESE INSTRUCTIONS
86037660 CHARIOT 11/09/06
2-1
HAZARD INTENSITY LEVEL
The following symbols are used throughout this guide as indicated in their descriptions:
HAZARD INTENSITY LEVEL
There are three levels of hazard intensity identified by signal words -WARNING and CAUTION and FOR
SAFETY. The level of hazard intensity is determined by the following definitions:
WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death.
CAUTION - Hazards or unsafe practices which could result in minor personal injury or product or property
damage.
FOR SAFETY: To Identify actions which must be followed for safe operation of equipment.
Report machine damage or faulty operation immediately. Do not use the machine if it is not in proper operating
condition. Following is information that signals some potentially dangerous conditions to the operator or the
equipment. Read this information carefully. Know when these conditions can exist. Locate all safety devices on
the machine. Please take the necessary steps to train the machine operating personnel.
FOR SAFETY:
DO NOT OPERATE MACHINE:
Unless Trained and Authorized.
Unless Operation Guide is Read and understood.
In Flammable or Explosive areas.
In areas with possible falling objects.
WHEN SERVICING MACHINE:
Avoid moving parts. Do not wear loose clothing; jackets, shirts, or sleeves when working on the machine. Use
Windsor approved replacement parts.
Batteries emit hydrogen gas. Explosion or fire can result. Keep sparks and open flame away. Keep
solution tank in raised position when charging. Keep sparks and flames away from the batteries. Do not
smoke around batteries.
Disconnect batteries before working on machine. Only qualified personnel should work inside machine.
Always wear eye protection and protective clothing when working on or near batteries. Avoid skin contact
with the acid contained in the batteries.
Never allow metal to lie across battery tops.
2-2
86037660 CHARIOT 11/09/06
SAFETY LABEL LOCATION
NOTE: These drawings indicate the location of safety labels on the machine. If at any time the labels become
illegible, promptly replace them.
86244300
PRV NO. 500955
WARNING LABEL
86252520
PRV NO. 80885
BATTERY
CAUTION
86037660 CHARIOT 11/09/06
2-3
TECHNICAL SPECIFICATIONS
ITEM
Nominal power
Rated Voltage
Rated Amperage
Batteries
Battery Compartment Dimensions
Scrub Brush Motors - Disk Machine
Scrub Brush Motors - Cylindrical Machine
Vacuum Motor(s)
Maximum flow rate of vacuum motor
Maximum suction of vacuum motor
Propelling Motor
Mass (GVW)
Weight empty without batteries
Solution Control
Solution capacity
Recovery capacity
Scrub brush diameter - Disk Machine
Scrub brush diameter - Cylindrical Machine
Scrub brush pressure
Scrub brush speed - Disk Machine
Scrub brush speed - Cylindrical Machine
Tires
Foundation Pressure
Maximum Speed
Theoretical Coverage
Frame Construction
Brake
Minimum aisle u-turn width
Maximum rated climb and descent angle
3-1
DIMENSION/CAPACITY
2100 W
36 Volts DC
58 amps
3 X12 Volt 195-215 AH @ 20 hr. rate
21 in. x 16 in. x 17 in. tall
(533mm x 406mm x 432mm)
2 x .3 HP (190 W)
2 x .75 HP (560 W)
.75 HP (560 W)
77.0 cfm (36.4 liters per second)
81.8 inches of water (20.3 kPa)
.75 HP (560 W)
1245 lbs (565 kg)
535 lbs (243 kg)
1.3 GPM pump, fully variable with automatic shut-off
in neutral
25 gal (95 L)
25 gal (95 L)
12 inch (305 mm)
6 inch (152 mm)
0-150lbs (0-667N)
300 rpm
800 rpm
10 in. (254mm) Solid Scrubber Compound
104 psi (715 Kpa)
3.5 miles/hour (5.6 Km/hour)
24,200 ft²/hr @ 2.5 mph with 2 in. overlap
Powder coated steel
Electrical parking brake, sets automatically whenever
operator steps off platform or engages emergency
stop.
56 in. (1425 mm)
7.5 degrees
86037660 CHARIOT 11/09/06
TECHNICAL SPECIFICATIONS
ITEM
Height
Length
Width without squeegee
Width of squeegee - Disk Machine
Width of squeegee - Cylindrical Machine
Width of scrub path - Disk Machine
Width of scrub path - Cylindrical Machine
MEASURE
50.6 inches (1285 mm)
52.5 inches (1330 mm)
26.5 inches (670 mm)
32.7 inches (830 mm)
29 inches (737 mm)
24 inches (610 mm)
23 inches (585 mm)
LENGTH
WIDTH
HEIGHT
SPECIAL NOTES:
The sound pressure level at the operator’s ear was
measured to be 68 dBA. This was a nearfield, broadband measurement taken in a typical industrial
environment on a tile floor. This appliance contains no
possible source of impact noise. The instantaneous
sound pressure level is below 63 Pa.
The weighted root mean square acceleration at the
operator’s arms was measured to be below 2.5m/s2 .
This was a tri-axial, third-octave-band measurement
made during normal operation on a composite tile floor.
The measurement and related calculations were made
in accordance with ANSI S3.34-1986.
This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety. Children should be
supervised to ensure that they do not play with the
appliance.
86037660 CHARIOT 03/27/08
3-2
HOW THIS MACHINE WORKS
The Chariot® is a battery powered, self-propelled,
hard floor scrubber intended for commercial use.
The appliance applies a cleaning solution onto a
hard floor, scrubs the floor with brushes, and then
vacuums the soiled water back into the recovery
tank.
The machine's primary systems are the solution
system, scrub system, recovery system, and
operator control system.
The function of the solution system is to store
cleaning solution and deliver it to the scrub system.
The solution system consists of the solution tank,
strainer, pump, valve and controls. The solution
tank stores cleaning solution (water and detergent)
until it is delivered to the scrub system. The strainer
protects the pump from debris. The valve
automatically prevents solution flow unless the scrub
brushes are turned on and the machine is being
propelled. The solution control switch controls the
amount of cleaning solution delivered to the scrub
system by controlling the amount of time the pump is
on.
The function of the scrub system is to scrub the
floor. The disk scrub system consists of two rotary
type disk scrub brushes, motors, scrub deck skirt, lift
actuator and controls. The brushes scrub the floor
as the motors drive the brushes. The brush drive
hubs allow the scrub brushes to follow irregularities
and changes in the floor without loosing contact with
the floor. The scrub deck skirts control the cleaning
solution on the floor so that the squeegee can pick it
up. The one touch/brush switch controls the motors
and lift actuator to turn the motors on and lower the
deck, or turn the motors off and raise the deck. The
brush pressure switch controls the down pressure
on the scrub deck.
The scrub deck side squeegees control the cleaning
solution on the floor so that the squeegee can pick it
up. The brush pressure switch controls the motors
and lift actuator to turn the motors on and lower the
deck, or turn the motors off and raise the deck. The
brush pressure switch also controls the down
pressure on the scrub deck.
The function of the recovery system is to vacuum
the soiled water back into the recovery tank. The
recovery system consists of the squeegee, vacuum
motor, float ball filter, recovery bag and controls.
The squeegee wipes the dirty solution off the floor
as the machine moves forward. The vacuum motor
provides suction to draw the dirty solution off the
floor and into the recovery bag. The float ball filter
protects the vacuum fan from debris and foam. The
recovery bag stores the dirty solution.
The function of the operator control system is to
control the direction and speed of the machine. The
directional control system consists of the direction
control switch, throttle pedal, operator presence
pedal, speed control switch, drive reset switch,
emergency stop/brake switch, steering wheel, propel
controller, and drive wheel. The directional control
switch signals forward or reverse direction. The
controller interprets signals from the throttle pedal to
command the drive wheel to propel or slow the
machine. The drive reset switch is to make sure the
operator is on platform before machine will propel.
The operator presence pedal is to make sure the
operator keeps both feet safely on platform while
driving. The steering wheel points the drive wheel in
the direction desired by the operator. The parking
brake automatically engages when the operator
steps off the platform. The emergency stop/brake
can be used to hold the machine on slopes.
The scrub plus system consists of two cylindrical
type brushes, motors, scrub deck side squeegees,
hopper, lift actuator, and controls. The cylindrical
scrub head is designed to eliminate debris that may
be caught in the squeegee while scrubbing. Water
is applied to the first scrubbing brush turning in a
clockwise rotation when viewed from the right side of
machine. The first brush scrubs dirt and debris
between the brushes. The second scrubbing brush,
turning in a counter clockwise rotation, picks up
debris and throws it into a removable hopper. Water
is allowed to drain out the hopper into the squeegee
path where it is recovered from the floor.
3-3
86037660 CHARIOT 11/09/06
COMPONENTS
2
1
7
3
11
5
6
12
10
4
9
8
1.
2.
3.
4.
5.
6.
Control Panel-Drive
Control Panel-Scrub
Control Housing
Pedal Platform
Rear Cover
Tank
7.
8.
9.
10.
11.
12.
Recovery Dome
Recovery Drain Hose
Scrub Deck Aqua-Mizer
Scrub Deck Skirts/Side Squeegees
Solution Cover
Solution Drain Hose
86037660 CHARIOT 11/09/06
3-4
DRIVE CONTROLS
10 (Basic)
2
8
6
3
1
7
11 (Basic)
9
5
3-5
4
86037660 CHARIOT 11/09/06
DRIVE CONTROLS
1.
2.
3.
4.
5.
6.
1.
Key Switch
Emergency Stop/Brake Switch
Directional Control Switch
Throttle Pedal
Operator Presence Pedal
Speed Control Switch
7.
8.
9.
10.
11.
Drive Reset Button
Horn Button
Steering Wheel
Battery Discharge
Indicator (Basic Only)
Hour Meter (Basic Only)
KEY SWITCH
Controls the power for machine functions.
To turn the machine power on, rotate key clockwise.
To turn the machine off, rotate key counterclockwise.
Deluxe Only: When the key is turned on the battery symbol will flash while the system runs self-diagnostics
and returns scrub deck and squeegee to their raised positions, if necessary. The controller will not respond to
other commands until this routine is complete.
2.
EMERGENCY STOP/BRAKE SWITCH
This safety feature is designed to cut all power to the machine at any time and apply parking brake.
To shut the machine power off, push the Emergency Stop Switch, this will also engage the parking brake and
cause the machine to stop immediately.
To reset the machine, rotate the switch clockwise.
3.
DIRECTIONAL CONTROL SWITCH
Controls the direction of travel of the vehicle. The position of the switch indicates direction of travel.
To travel forward, press the top of the switch.
To travel in reverse, press the bottom of the switch.
4.
THROTTLE PEDAL
Controls the speed of the vehicle within the speed control setting selected. Pressing the pedal causes the
machine to travel in the direction selected by the Directional Control Switch.
To increase speed, increase pressure on the pedal.
To decrease speed, decrease pressure on the pedal.
5.
OPERATOR PRESENCE PEDAL
This safety feature is designed to ensure that the operator has their left foot on pedal platform whenever
machine is moving. The operator must have left foot on Operator Presence Pedal for machine to move.
86037660 CHARIOT 11/09/06
3-6
DRIVE CONTROLS
6.
SPEED CONTROL SWITCH
Controls the maximum speed of the machine. There are two setting intended for scrubbing, speeds 1 and 2.
Speed 3 is recommended for transport only, not scrubbing.
To increase speed, press the top of the switch.
To decrease speed, press bottom of the switch. Speeds can be adjusted at any time, whether machine is
moving or not.
Basic: The position of the switch indicates speed setting.
Deluxe: The display indicates speed setting. When the key is turned on the controller will automatically
adjust the speed to setting 2.
7.
DRIVE RESET SWITCH
This safety feature is designed to ensure safe engagement of propel drive. Each time the machine power is
turned on, and each time an operator steps on to the platform, the Drive Reset Switch must be pushed
before machine will propel.
8.
HORN BUTTON
The horn is activated by pressing the horn button.
9.
STEERING WHEEL
The steering wheel turns the front wheel causing the machine to change direction.
3-7
86037660 CHARIOT 11/09/06
DRIVE CONTROLS
10A. BATTERY CHARGE LEVEL INDICATOR-BASIC
Indicates the charge level of the batteries.
The meter display is divided into 10 vertical bars. Bars illuminated on the far right indicate full charge. Bars
flashing near the left side indicate the batteries should be recharged. Further operation of the machine
could damage the machine or the batteries.
When the machine is left overnight with less than a full charge, the display may initially indicate a full
charge. It will also indicate a full charge if the batteries are disconnected, then reconnected. After a few
minutes of operation the meter will give the correct charge level.
10B. BATTERY CHARGE LEVEL INDICATOR-DELUXE
The battery meter can be viewed at the left side of either information screen 1 or information screen 2. The
level of battery charge is indicated by the horizontal bars in the battery meter box. When the batteries
require charging, the icon will flash and a battery inhibit icon will appear on the right side of either
information screen. Scrub and solution functions that are running when the battery inhibit icon appears will
be automatically shut off. It is not possible to restart scrub functions while the battery inhibit is displayed.
The controller reserves enough battery charge to allow pick-up of residual water and transport back to a
charging station.
11A. HOUR METER-BASIC
Records the number of hours the machine has been in operation. This information is useful in determining
when to service the machine.
11B. HOUR METER-DELUXE
Brush Run Time:
Records the time spent with the brushes running
and gives true brush motor time.
Traction Motor Time:
Records the time spent propelling the machine
and gives true traction motor time.
86037660 CHARIOT 11/09/06
3-8
SCRUB CONTROLS-BASIC AND CYLINDRICAL
4
2
3
1
1.
2.
3-9
Squeegee Lift Lever
Scrub Deck Actuator Switch
3. Brush Pressure Indicator
4. Solution Control Knob
86037660 CHARIOT 11/09/06
SCRUB CONTROLS-BASIC-CYLINDRICAL
1. SQUEEGEE LIFT LEVER
Raises and lowers the squeegee, and turns the vacuum motor on and off.
To lower squeegee and start vacuum motor, lift the lever from its raised position.
To raise squeegee and stop vacuum motor, lift the lever from its lowered position.
2. ACTUATOR SWITCH
Raises and lowers the scrub deck, turns the scrub brush motors on and off, and adjusts the amount of
brush/pad pressure to the floor.
To lower the scrub deck, turn on scrub brush motors, and/or increase brush pressure, press the bottom of
the switch.
To raise the scrub deck, turn off scrub brush motors, and/or decrease brush pressure, press the top of the
switch.
3. BRUSH PRESSURE INDICATOR
The brush pressure indicator corresponds to the amp draw of the scrub brush motors to tell how hard the
motors are working. The blue zone indicates medium or proper brush pressure. The red zone indicates
heavy or excessive brush pressure. Operating in the red zone may cause the brush circuit breakers to trip.
4. SOLUTION CONTROL KNOB
Controls solution flow to scrub deck
To increase flow, rotate knob clockwise.
To decrease flow, rotate knob counterclockwise.
If the brush motors are turned off or the throttle pedal is in neutral, the flow is automatically interrupted until
the motors are turned on again. This feature prevents unintentional draining of the solution tank and allows
the operator to adjust the solution flow to the scrub deck without resetting each time the scrubbing
operation is interrupted.
86037660 CHARIOT 11/09/06
3-10
SCRUB CONTROLS-DELUXE
5
1
4
1. One Touch Switch
2. Solution Control Switch
3. Brush Pressure Switch
3
2
4. Vacuum/Squeegee Switch
5. Display Toggle Switch
1. ONE TOUCH SWITCH
This switch controls the scrub brushes and vacuum all in one touch.
To start scrubbing, press the one touch switch. The brush drive motors will turn on, the scrub deck will
lower to the "light scrub" position, the solution will flow at “one bar” rate, the squeegee will lower and the
vacuum will turn on. The information display window will show which functions are operating. If the throttle
pedal is in the neutral position for more than two seconds the brushes and solution flow will stop. If the one
touch switch is activated without brushes installed, the brush motors will stop, the scrub deck will rise, and
the brush pressure indicator will display error code 9000.
To stop scrubbing, press the one touch switch. The brush drive motors will turn off, the scrub deck will
raise the solution flow will stop, the squeegee will raise after a 15 second delay, and the vacuum motor will
turn off. This delay is to clear the vacuum hose of recovered solution.
3-11
86037660 CHARIOT 11/09/06
SCRUB CONTROLS-DELUXE
2. SOLUTION CONTROL SWITCH
This switch controls the amount of solution flow to the scrub deck. The information screen will show the
solution setting. There are 4 different flow settings.
To increase the solution flow, press the bottom of the solution control switch (+).
To decrease solution flow, press the top of the switch (-).
If the brush motors are turned off or the throttle pedal is in neutral, the flow is automatically interrupted until
the motors are turned on again, or the throttle pedal is pressed down. This feature prevents unintentional
draining of the solution tank and allows the operator to adjust the solution flow to the scrub deck without
resetting each time the scrubbing operation is interrupted.
3. BRUSH PRESSURE SWITCH
This switch controls the amount of brush pressure to the floor. The information display screen will show the
amount of pressure. There are 4 different pressure settings.
To decrease the amount of down pressure, press the top of the brush pressure switch (-).
To increase the amount of down pressure, press the bottom of the brush pressure switch (+).
4. VACUUM/SQUEEGEE SWITCH
This switch independently controls the vacuum motor and squeegee position.
To start the vacuum motor and lower the squeegee to the floor, press the bottom of the switch.
To raise the squeegee and turn off the vacuum motor, press the top of the switch. The squeegee will raise
after a 15 second delay, and the vacuum motor will turn off 15 seconds later, in order to clear vacuum hose
of recovered solution.
5. DISPLAY TOGGLE SWITCH
The display toggle switch allows you to change the information displayed screen. Two screens are
available.
Screen 1 displays battery charge level, speed setting, brush pressure setting and solution flow setting, as
well as animated scrub brush and vacuum icons when these functions are engaged.
Screen 2 displays battery charge level and hour meters. Hours are displayed for brush run time and
traction motor time.
86037660 CHARIOT 11/09/06
3-12
SCRUB CONTROLS-SQUEEGEE
1
2
2
DISK SCRUBBER
CYLINDRICAL SCRUBBER
1. Squeegee Deflection Adjustment Knobs
2. Squeegee Pitch Adjustment Rod
3-13
86037660 CHARIOT 11/09/06
SCRUB CONTROLS-SQUEEGEE
1. SQUEEGEE DEFLECTION ADJUSTMENT
KNOBS
Adjusts the deflection along the entire length of
the squeegee.
To increase squeegee blade deflection, turn the
two knobs at the ends of the squeegee
counterclockwise.
To decrease squeegee deflection, turn the two
knobs at the ends of the squeegee clockwise.
2. SQUEEGEE PITCH ADJUSTMENT ROD
(DISK SCRUBBER)
Adjusts the deflection at the ends of the
squeegee.
To increase squeegee blade deflection at the
ends, turn rod counterclockwise.
To decrease squeegee blade deflection at the
ends, turn rod clockwise.
SQUEEGEE PITCH ADJUSTMENT KNOB
(CYLINDRICAL)
Adjusts the deflection at the ends of the
squeegee.
To increase squeegee blade deflection at the
ends, turn knob counterclockwise.
To decrease squeegee blade deflection at the
ends, turn knob clockwise.
86037660 CHARIOT 11/09/06
3-14
MACHINE OPERATION
PRE-RUN MACHINE INSPECTION
EMERGENCY STOP PROCEDURES
Do a pre-run inspection to find possible problems
that could cause poor performance or lost time from
breakdown. Follow the same procedure each time to
avoid missing steps.
1. Release the throttle pedal by lifting right foot.
NOTE: See maintenance section for pre-run
machine inspection checklist items.
3. If an electrical problem is suspected, push in
emergency stop button. This will also engage
the parking brake and cause the machine to
stop immediately.
STARTING MACHINE
2. Turn machine power off with key switch, by
turning key switch counterclockwise.
NOTE: Perform pre-run machine check before
operating machine.
FOR SAFETY: Before starting machine, make
sure that all safety devices are in place and
operating properly.
1. The operator should be on the pedal platform
with their left foot on the operator presence
pedal. The throttle pedal must be in the neutral
position.
2. Turn the machine power on by turning key
switch clockwise to the “ON” position.
3. Check the position of the Directional Control
Switch to make sure the machine will travel in
the direction intended.
4. Press the Drive Reset Switch.
5. Press lightly on the throttle pedal with right foot.
3-15
86037660 CHARIOT 11/09/06
MACHINE OPERATION
FILLING SOLUTION TANK
NORMAL SCRUBBING
FOR SAFETY: Before leaving or servicing
machine; stop on level surface, turn off machine
and remove key.
Plan the scrubbing pattern in advance. The longest
track is around the perimeter of the area to be
cleaned. For efficient operation, the runs should be
the longest possible without turning, stopping, or
raising or lowering scrub deck/squeegee.
1.
Turn the machine power off.
2.
Remove solution cover.
3.
Fill the solution tank with clean water, leaving
enough room for the required amount of
cleaning solution. The solution tank capacity
filled to fill inlet is 25 gallons (95 liters). The
water must not be hotter than 140° F (60°C) to
prevent damage to the tank.
4.
Measure the chemical into the solution tank.
Liquid chemicals should be added to the
solution tank after filling with water. Dry
chemicals should be thoroughly mixed before
being added into solution tank. Commercially
available, high alkaline floor cleaners, are
suitable for use in the solution system.
In order to achieve the best possible results, the
area which is to be cleaned should be swept before
scrubbing. Large debris, strings and wire must be
removed to prevent being caught in brushes or
squeegee.
If the machine is allowed to stand in neutral with the
scrub deck down for more than 2 seconds, the
solutions flow stops and brush motors stop. If either
forward or reverse travel is selected, the solution
flow will continue in the same setting and the scrub
brush motors will continue in their same setting once
movement of machine begins. Overlap the brush
path and avoid transporting over previously cleaned
areas.
NOTE: Read the chemical manufacturers
recommended proportion instructions.
5. Replace solution tank cover.
Flammable materials
can cause an
explosion or fire. Do not use flammable
materials in the tanks.
86037660 CHARIOT 11/09/06
3-16
MACHINE OPERATION
TO BEGIN SCRUBBING
PRIMING PUMP
When operating the machine around people, pay
close attention for unexpected movement. Use
extra caution around children.
If the solution system has gone dry or has been
unused for a period of time, it may be necessary to
follow the pump priming procedure.
Flammable liquids and/or reactive metals can
cause explosions or fire! Do not pick up.
1. Fill solution tank.
1.
Place left foot on operator presence pedal.
Throttle pedal must be in neutral position.
2.
Turn machine power on.
3.
Check position of Directional Control Switch to
ensure that machine is set to travel in direction
intended.
2. Loosen, but do not completely remove the
strainer bowl. Solution should flow out of the
strainer. If it does not, check the strainer screen
inside the solution tank. Insure it is clear of
debris. Tighten the strainer bowl.
3. Disconnect the squeegee hose from the
recovery dome.
4.
Press the Drive Reset Switch.
4. Begin normal scrubbing and set the solution flow
to maximum setting. Solution flow should begin
within 2 minutes.
5.
BASIC AND CYLINDRICAL
5. Connect squeegee hose to recovery dome.
Lower the squeegee.
6. Adjust the speed of the machine, solution flow
and scrub brush pressure as necessary.
Lower the scrub deck to floor.
DELUXE
Press the one-touch switch (#1) on the control
panel. The brush motors will start, the scrub
deck will lower to the light scrub position, the
solution will begin to flow, the squeegee will
lower to the floor and the vacuum motors will
start.
6.
Drive machine forward to begin scrubbing.
NOTE: Shut machine off immediately if water or
foam is expelled from the machine.
7.
Adjust the speed of the machine, solution flow
and scrub brush pressure as necessary.
NOTE: Once solution flow rate is set it is not
necessary to shut off solution when stopping
scrubbing. Solution flow is automatically shut off
when brush motors stop. When brush motors are
activated, flow automatically resumes.
3-17
86037660 CHARIOT 11/09/06
MACHINE OPERATION
TO STOP SCRUBBING
DOUBLE SCRUB
1. BASIC AND CYLINDRICAL
For floors which are heavily soiled or have thick
accumulations of floor finish may not clean
sufficiently with one pass. In these cases it will be
necessary to double scrub.
To double scrub, make the first pass over the
surface being cleaned with the squeegee up,
vacuum off, the solution on, Aqua-Mizer removed
and brushes down. This allows the solution to stay in
contact with the soil while loosening the surface
accumulation with the brushes. Allow time for the
first application to stay in contact with the floor.
Length of time between the first and second pass
depends on amount of accumulation and the type of
chemical being used. A second scrubbing with the
squeegee down and again the solution and brushes
on will further loosen soil. The additional application
of solution will further assist the difficult cleaning job.
Raise the scrub deck, turn off scrub
brushes.
Raise squeegee, turn off vacuum.
DELUXE
Press the one-touch switch (#1) on the
control panel. The brush motors will stop
and the scrub deck will rise to the park
position. After 15 seconds the squeegee
will raise, and 15 seconds later the vacuum
motor will turn off. This delay is to clear the
vacuum hose of recovered solution.
2. Allow the throttle pedal to return to neutral.
FOR SAFETY: When using machine, go slow on
inclines and slippery services.
3. Turn machine power off.
FOR SAFETY: Before leaving or servicing
machine: stop on level surface, turn off machine
and remove key.
86037660 CHARIOT 11/09/06
3-18
MACHINE OPERATION
SOLUTION TANK
1. Pull recovery drain hose out to expose the
solution drain hose.
2. Pull the solution drain hose from under front of
the tank. Unscrew the T-handle on plug enough
to loosen plug, then lower hose in direction of
drain. Slowly remove plug from drain hose.
3. Remove the solution tank cover.
SOLUTION
DRAIN HOSE
RECOVERY
DRAIN HOSE
4. Flush the solution tank out with clean water and
run several gallons of clean water through
systems. Do not use water hotter than 140°F
(60°C) to clean tank. Damage may occur.
NOTE: Never allow solution to remain in tank.
Damage to tank, seals and valves could occur.
EMPTYING AND CLEANING TANKS
1.
Park the machine next to a floor drain. Drain
hoses are at the front of the machine.
2.
Turn the machine power off.
Tuck drain hose under tank and secure with
recovery drain hose by tucking it under tank.
RECOVERY TANK
1.
Pull the large drain hose from under the front of
the tank. Unscrew cap, then lower hose in
direction of the drain. Do not stand in front of
end of hose. Recovered solution will come out
with force.
2.
Remove the recovery tank dome. Flush the
recovery bag out with clean water. Do not use
water hotter than 140°F (60°C) to clean tank.
Damage may occur.
3.
Clean debris from dome basket.
4.
Clean off the float shut-off system and inspect
for free movement of float. The float shut-off
system is located in the rear of the recovery
tank.
5.
Replace the drain cap and secure drain hose
under tank.
6.
If machine is to be stored, leave the recovery
tank dome off.
3-19
86037660 CHARIOT 11/09/06
NOTES:
86037660 CHARIOT 11/09/06
3-20
MAINTENANCE
SERVICE SCHEDULE
MAINTENANCE
Check water level of batteries after charging;
add distilled water if necessary. (Wet cell only)
Check that dome and cover seal tightly.
Visually check for damaged or worn tires.
Check brushes or pads for proper installation.
Check vacuum hose connections.
Check that squeegee is securely attached and
properly adjusted.
Check for securely attached drain hoses, plug
and cap.
Check both pedals, brake and steering for
proper operation.
Clean out recovery tank and dome basket.
Clean and inspect float shutoff.
Clean out solution tank and filter, check flow.
Clean and inspect solution filter strainer.
Run vacuum motors to dry.
Clean brushes or pads and check wear.
Clean squeegee blades and check wear.
Clean outside of tanks, check for damage.
Store with dome off tank.
Charge batteries.
Clean off top of batteries.
Check battery cells with hydrometer. (Wet cell
only)
Inspect scrub deck skirts and Aqua-Mizers.
Clean solution strainer inside tank.
Check battery connections are tight.
Clean battery cases and battery compartment.
Clean and check drive tension chain for wear
and tension.
Check parking brake.
Clean chains, cables and pulleys for
squeegee lift.
Clean pivot points on squeegee and scrub
deck.
Check all motors for carbon brush wear.
Check motor commutators.
Check steering chain tensioner.
BEFORE EACH
WORK PERIOD
AFTER EACH
WORK
PERIOD
50
HRS
100
HRS
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
NOTE: Traction drive, wheels and batteries should be serviced based on traction drive hour meter
(Deluxe). The scrub brush hour meter should be used for all other service schedule items.
4-1
200
HRS
86037660 CHARIOT 11/09/06
*
*
*
*
*
*
MAINTENANCE-BATTERIES
1
2
3
4
5
6
1.
2.
3.
Rear Cover Retainer Knob
Rear Cover
Battery Connector-Machine
4.
5.
6.
Batteries
Battery Tray
Battery Tray Latch
86037660 CHARIOT 11/09/06
4-2
MAINTENANCE-BATTERIES
When servicing machine,
avoid contact with battery
acid.
BATTERIES (WET CELL ONLY)
The batteries provide the power to operate the
machine. The batteries require regular maintenance
to keep them operating at peak efficiency.
The machine batteries will hold their charge for long
periods of time, but they can only be charged a
certain number of times. To get the greatest life
from the batteries, charge them when their charge
level reaches 25% of a full charge. Use a
hydrometer to check the charge level.
Do not allow the batteries to remain in a discharged
condition for any length of time. Never expose a
discharged battery to temperatures below freezing.
Discharged batteries will freeze causing cracked
cases. Do not operate the machine if the batteries
are in poor condition or if they have a charge level
below 25% (specific gravity below 1.155).
Keep all metallic objects off the top of the batteries,
as they may cause a short circuit. Replace worn or
damaged cables and terminals.
Check the electrolyte level in each battery cell
before and after charging the batteries. Never add
acid to the batteries, use distilled water. Do not
allow water level to fall below the battery plates.
Portions of plates exposed to air will be destroyed.
Do not overfill. Keep plugs firmly in place at all
times.
Batteries emit hydrogen
gas. Explosion or fire can
result. Keep sparks and open flame away. Keep
covers open when charging.
Wear eye protection and
protective clothing when
working with batteries.
Charge batteries in a well
ventilated area.
BATTERY MAINTENANCE
1. When cleaning the batteries, use a solution of
baking soda and water. Do not allow the
cleaning fluid to enter the battery cells,
electrolyte will be neutralized.
2. Maintain the proper electrolyte level in each
battery cell. If a cell should accidentally
overflow, clean immediately.
3. Wipe off the top of the batteries at least once a
week.
4. Test battery condition with a hydrometer at least
once a week.
5. Ensure that all connections are tight and all
corrosion removed.
6. Every 4 to 6 months, remove that batteries from
the machine and clean the battery cases and
battery compartment.
4-3
86037660 CHARIOT 11/09/06
MAINTENANCE-BATTERIES
CHECKING BATTERY SPECIFIC GRAVITY
CHARGING BATTERIES
Use a hydrometer to check the battery specific
gravity.
When servicing machine,
avoid contact with battery
acid.
Batteries emit hydrogen
gas. Explosion or fire can
result. Keep sparks and open flame away. Keep
covers open when charging.
Battery Check
Wear eye protection and
protective clothing when
working with batteries.
Charge batteries in a well
ventilated area.
CHECKING GRAVITY
A. Hydrometer
B. Battery
Use a 36 volt, 20 amp maximum output DC charger
which will automatically shut off when the batteries
are fully charged.
NOTE: Do not take readings immediately after
adding distilled water, if the water and acid are not
thoroughly mixed, the reading may not be accurate.
1. Stop the machine in a clean, well ventilated area
next to the charger.
Check the hydrometer readings against this chart.
2. Turn “OFF” machine.
SPECIFIC GRAVITY
@ 80° F (27°C)
1.265
1.225
1.190
1.155
1.120
BATTERY CONDITION
100% CHARGED
75% CHARGED
50% CHARGED
25% CHARGED
DISCHARGED
NOTE: If the readings are taken when the battery
electrolyte is any temperature other than 80°F
(27°C), the reading must be temperature corrected.
To find the corrected specific gravity reading when
the temperature of the battery electrolyte is other
than 80°F (27°): Add (+) to the specific gravity
reading 0.004 (4 points), for each 10°F (6°C) above
80° (27°C).
Subtract (-) from the specific reading 0.004 (4
points), for each 10°F (6°C) below 80°F (27°C).
FOR SAFETY: Before leaving or servicing
machine; stop on level surface, turn off machine
and remove key.
3. Remove rear cover, unplug batteries from
machine, unlatch battery tray and pull out to
expose batteries.
Batteries emit hydrogen
gas. Explosion or fire
can result. Keep sparks and open flame away.
Keep covers open when charging.
4. Check the electrolyte level in each battery cell.
Before charging, add just enough distilled water
to cover the plates. After charging is complete,
add just enough distilled water to bring up the
level to the indicator ring. If the water level is
too high before charging, normal expansion rate
of the electrolyte may cause an overflow
resulting in a loss of battery acid balance and
damage the machine.
86037660 CHARIOT 11/09/06
4-4
MAINTENANCE-BATTERIES
5. Replace the battery caps, and leave them in
place while charging.
6. Unplug the battery connector from the machine.
FOR SAFETY: When charging, connect the
charger to the batteries before connecting the
charger to the AC wall outlet. Never connect the
charger to the AC wall outlet first. Hazardous
sparks may result.
7. Plug the charger connector into the battery
connector. Connect the charger AC plug to a
wall outlet. The charger gauge should indicate
that the batteries are charging.
8. When the batteries are fully charged, disconnect
the charger from the AC wall outlet, then
disconnect the charger from the batteries.
CHANGING BATTERIES
Stop the machine in a clean area next to the
charger. Turn off machine.
FOR SAFETY: Before leaving or servicing the
machine; stop on level surface, turn off machine
and remove key.
1.
Remove the rear cover.
2.
Disconnect battery pack from machine.
3.
Unlatch battery tray from machine and pull out
to expose batteries.
4.
Use the proper size open end wrench to
disconnect main ground wire first and secure
cable terminal away from batteries.
5.
Disconnect main positive lead and secure cable
terminals away from batteries.
6.
Loosen both terminals on each jumper cable
and remove one at a time.
7.
Prepare a suitable site to place the batteries.
9. Connect the batteries to the machine connector.
10. Check the electrolyte level. It should be up to
the indicator ring. If necessary, add distilled
water.
11. Install the rear cover.
Attach suitable battery lifting
device and lift batteries from
the machine.
Batteries are a potential environmental hazard.
Consult your battery supplier for safe disposal
methods.
RED
+
BLK
-
RED
+
BLK
-
RED
+
BLK
-
REAR OF MACHINE
4-5
86037660 CHARIOT 11/09/06
MAINTENANCE-SQUEEGEE
1
2
3
4
5
6
4
DISK SCRUBBER
1.
2.
3.
6
CYLINDRICAL SCRUBBER
Squeegee
Squeegee Deflection Adjustment Knobs
Squeegee Level Indicator
4.
5.
6.
Squeegee Pitch Adjustment
Rod/Cylindrical Knob
Squeegee Pitch Adjustment Lock Nut
Squeegee Retainer Knob
86037660 CHARIOT 11/09/06
4-6
MAINTENANCE-SQUEEGEE
SQUEEGEE BLADES
TO REMOVE SQUEEGEE ASSEMBLY
The front squeegee blade allows solution to pass
through channels in the blade into the squeegee
assembly while maintaining vacuum to provide lift.
The front blade has four wear surfaces and can be
rotated for extended life. The front blade should not
require regular replacement under normal use.
1. With the squeegee in the up position, turn key
switch “OFF”.
The rear blade wipes the floor to a near dry
condition. It is important the rear blade be in good
condition to properly do its job. As with the front,
each squeegee blade assembly has four wear
surfaces for extended service.
3. Pull squeegee assembly from the lifting carrier.
Check both the front and rear squeegee blades for
damage, wear, and adjustment each day in the prerun check. Change the front blade if it is torn or has
an uneven edge. Change the rear blade if it is less
than 1/2 the original thickness.
ADJUSTING SQUEEGEE
Adjusting the squeegee is a two-part process. First,
the squeegee assembly must have correct pitch in
order for the squeegee blade to have the same
deflection at each tip as well as the center. The rod
on the squeegee linkage controls the pitch
adjustment. The second adjustment is the
deflection. Knobs on each end of the squeegee
control this.
2. Disconnect vacuum hose from squeegee and
loosen knob on left side of squeegee lifting
carrier.
4. Inspect or repair as necessary and reinstall.
TO REPLACE OR ROTATE REAR SQUEEGEE
BLADES
1. With the squeegee in the up position, turn key
switch “OFF”.
FOR SAFETY: Before leaving or servicing
machine; stop on level surface, turn off machine
and remove key.
2. Remove the squeegee assembly from the
machine. Unlatch and remove blade retainer
strap and remove squeegee blade.
3. Rotate the squeegee to new edge position or
replace as required. Each blade has four new
edge positions.
4. Install blade on locating pins of squeegee
assembly.
SQUEEGEE DEFLECTION
5. Install squeegee retainer strap.
3"
8
(9.5mm)
CORRECT
6. Fasten and lock latch, adjust latch only tight
enough to take up slack in retaining strap.
TO REPLACE OR ROTATE FRONT SQUEEGEE
BLADE
NOT ENOUGH
2. Remove the squeegee from the machine.
Loosen thumbscrews and remove the retainer
strap and squeegee blade.
TOO MUCH
SIDE VIEW OF SQUEEGEE BLADE
4-7
1. With the squeegee in the up position, turn key
switch “OFF”.
3. Rotate the squeegee to new edge position or
replace as required. Each blade has four new
edge positions. When installing the front blade,
tighten the center thumbscrew first. Insure that
the retainer strap is pressed against the blade
before tightening the outer screws.
86037660 CHARIOT 11/09/06
MAINTENANCE-SQUEEGEE
TO ADJUST SQUEEGEE PITCH
TO ADJUST AMOUNT OF REAR SQUEEGEE
DEFLECTION
1. Choose a smooth, level surface. Turn “ON” the
key switch. Lower the squeegee and drive
forward at least 2 feet (60cm.).
2. With the squeegee down, stop the machine. Do
not allow machine to roll back.
FOR SAFETY: Before leaving or servicing the
machine; stop on level surface, turn off machine
and remove key.
3. Determine the differences, if any, in deflection of
the squeegee blade between each end and the
middle. Proper adjustment is obtained when
deflection is equal all the way across the
squeegee blade. The bubble level should also
indicate when the squeegee is adjusted
properly. When the air bubble is in the center of
the vial, the deflection should be even across
the squeegee blade.
4. To decrease the deflection of the squeegee
blade at the ends, loosen wing nut and rotate
the rod clockwise. To increase the deflection at
the ends of the squeegee assembly, rotate the
rod counterclockwise knob.
5. Check the deflection of the squeegee blades
again. Repeat steps 1 through 4 until the
deflection is equal across the entire rear
squeegee blade. Tighten wing nut.
SQUEEGEE DEFLECTION
3"
8
(9.5mm)
CORRECT
SIDE VIEW OF SQUEEGEE BLADE
1. Choose a smooth, level surface. Lower the
squeegee and drive forward at least 2 feet
(60cm).
2. With the squeegee down, stop the machine. Do
not allow machine to roll back.
FOR SAFETY: Before leaving or servicing
machine; stop on level surface, turn off machine
and remove key.
3. Observe the amount of squeegee deflection. It
should deflect 3/8 in. (9.5mm) across the entire
width of the squeegee.
4. To increase the squeegee deflection, turn the 2
knobs at the squeegee ends counter-clockwise.
To decrease the deflection, turn the knobs
clockwise.
NOTE: The deflection should be consistent along
the length of the squeegee. If the deflection varies
from end to end the knobs can be adjusted
independently to correct the variation.
5. Turn on the key switch. Raise, then lower
squeegee assembly. Drive forward at least
2 feet (60cm).
6. Repeat steps 2 through 4 until deflection of
3/8 in. (9.5mm) is reached.
86037660 CHARIOT 11/09/06
4-8
MAINTENANCE-SCRUB BRUSHES
SCRUB BRUSHES
FINISHED FLOORS
There are four different types of brushes available to
cover applications from cleaning heavily soiled floors
to polishing. A pad driver is also available to take
advantage of the many cleaning pads on the market.
Please refer to the following to assist in selecting the
proper brush or pad for the work at hand.
Nylon bristles are used in a variety of applications
on coated or uncoated surfaces.
UNCOATED FLOORS
Red Pads (Buffing) are used for light-duty
scrubbing. When used with a mild detergent they
will provide surface cleaning without removing the
finish.
Aggressive Grit is a nylon fiber impregnated with
silicone carbide grit. It grinds away stain, soil, and
removes surface material.
Mild Grit is a less aggressive silicone carbide grit
suitable for cleaning medium soil conditions.
Advantages are faster ground speed than nylon
bristles on light solid applications.
Polypropylene is a general-purpose scrub brush
with stiff bristles. Polypropylene works well for
maintaining concrete, wood and tile floors.
White Pads (Polishing) are used for dry polishing to
achieve a high-gloss appearance, or surface
washing on highly polished or burnished floors.
Blue Pads (Scrubbing) are used for heavy-duty
scrubbing and light stripping. The blue pads remove
less finish than brown stripping pads, yet will remove
black marks, stains and dirt.
Black Pads (Stripping) are used for easy and
complete removal of old floor waxes/finishes. They
will quickly remove ground in dirt, black heel marks,
and spills. When used with the proper stripper, this
pad leaves the floor clean and ready for finishing.
The scrub brushes should be checked before each
days work for wire, string, wear and damage.
4-9
86037660 CHARIOT 11/09/06
MAINTENANCE-SCRUB DECK – DISK
4
3
1
2
5
6
1. Scrub deck Aqua-Mizer™
2. Aqua-Mizer™ retainer knob
3. Scrub deck skirt
4. Scrub deck skirt stop
5. Scrub brush motor
6. Scrub deck lift actuator
86037660 CHARIOT 11/09/06
4-10
MAINTENANCE-SCRUB DECK - DISK
Do not use a pressure
washer to clean around
the brush motors. Use tap pressure only.
BRUSH MOTOR CARBON BRUSH
REPLACEMENT
TO REPLACE SCRUB BRUSH MOTORS
1. Scribe alignment mark on motor barrel to motor
cap. Remove two bolts.
1. With the scrub deck in the raised position,
disconnect brush motor wiring connector from
harness.
2. Remove end cap from motor.
NOTE: Motors contain two wave washers in
cap. Do not lose these.
2. Remove skirts from scrub deck to access and
remove scrub brushes or pad drivers.
3. Remove Aqua-Mizers™ from scrub deck.
3. Release brush from spring tension. Remove
screw connecting brush wire lead to brush
holder. Clean brush holder to insure free
movement.
4. Remove retaining bolt, lock washer, flat washer
and star drive from brush motor shaft.
4. Retract spring and install new brush. Install
connector screw and lead.
5. Remove 4 brush motor mounting bolts located
under scrub deck.
5. When all new brushes are installed. Place all in
retracted position, held into brush holder by
spring tension.
6. Lower scrub deck.
7. Remove brush motor.
8. Reverse steps to install.
6. Carefully place end cap onto bearing on motor
shaft.
NOTE: Use care to assure wave washer
alignment.
7. With end cap in partially installed position,
release all brushes to contact position with
motor commutator.
NOTE: Failure to insure all brushes are released
will result in motor failure.
8. Reset end cap and realign with scribe marks on
motor barrel. Reinstall the two attach bolts from
cap into base.
9. Maintain alignment between motor barrel base
and cap.
4-11
86037660 CHARIOT 11/09/06
MAINTENANCE-SCRUB DECK - DISK
SCRUB DECK ACTUATOR ADJUSTMENT
FOR SAFETY: Before leaving or servicing
machine, stop on a level surface. Turn off
machine.
The actuator will need to be adjusted when
replaced.
To adjust the actuator:
1. Remove the two screws that secure actuator
spring plate and pull actuator barrel from stud on
actuator spring bracket.
2. Remove clevis pin from upper bracket of
actuator.
3. Disconnect actuator from wiring harness.
4. Reverse steps to install.
1. While holding actuator barrel to prevent it from
spinning, apply power to the actuator such that it
is fully extended. Positive power to white wire,
and negative/ground to black. Limit switch
within actuator will stop it.
2. Turn barrel out one or more full turns to assure
that when it is retracted it will not bind against
itself.
3. While holding actuator barrel to prevent it from
spinning, apply power to the actuator such that it
is fully retracted. Positive power to black wire,
and negative/ground to white wire. Limit switch
within actuator will stop it.
4. With actuator fully retracted, turn barrel in until it
touches the base of the threaded shaft.
5. At the bottomed out position, turn the barrel out
1 full turn, then enough more to allow
connection to lift linkage.
6. Connect actuator to lift linkage.
7. Check travel of actuator during operation.
86037660 CHARIOT 11/09/06
4-12
MAINTENANCE-SCRUB DECK - CYLINDRICAL
6
7
1
4
1.
2.
3.
4.
4-13
4-13
Hopper
Blade side squeegee
Side squeegee adjustment knob
Scrub brush motor
2
3
5
5. Scrub deck lift actuator
6. Side squeegee removal knob
7. Brush door
86037660 CHARIOT 11/09/06
MAINTENANCE-SCRUB DECK - CYLINDRICAL
SCRUB HEAD-CYLINDRICAL
SCRUB BRUSH REPLACEMENT
The dual cylindrical scrub head is designed to
eliminate debris that may be caught in the squeegee
while scrubbing. Water is applied to the first
scrubbing brush turning in a clockwise rotation when
viewed from the right of operator’s side of machine.
The first brush scrubs dirt and debris between the
brushes. The second scrubbing brush, turning in a
counter clockwise rotation, picks up debris and
throws it into a removable hopper. The larger debris
which might catch under the squeegee is collected
in the hopper. Water is allowed to drain out the
hopper into the squeegee path where it is recovered
from the floor.
1. Unscrew the knob and swing side squeegee out
about 90°
MAINTENANCE
5. Slide idler door up until lip rests on top of scrub
head.
The brushes should wear evenly side to side if
properly adjusted. Scrub brushes should be
exchanged front to back every 50 hours to ensure
even wear since the rear brush contacts the floor
with more force. It is not necessary to rotate end for
end since swapping front to back puts the brushes in
the opposite rotation, as well as balancing wear.
Scrub brushes should be replaced as a set when
bristle length wears to height of yellow
PerformAlertTM bristles.
2. Lift the drive side of the brush. Push brush until
a positive stop is felt. The idler plate cannot be
installed until the brush is fully seated on the
drive hub.
3. Allow brush to drop below scrub deck. Fully
insert plate onto brush.
4. Line up bottom hook on idler door with notches
on side of scrub head.
6. Hand tighten knob to secure door into place.
TO ADJUST SCRUB DECK SIDE SQUEEGEES
These skirts should be adjusted to 3/8” deflection.
To adjust:
1. Lower scrub deck to floor.
SCRUB BRUSH REMOVAL
2. Stop machine.
The scrub brushes are removed from the side of the
machine. The front is removed from the right side
and the rear is removed from the left side.
1. Unscrew the knob and swing side squeegee out
about 90°
3. Loosen scrub deck skirt stop.
4. Adjust stop such that skirt deflection is about
3/8”.
TO REPLACE SCRUB DECK SIDE SQUEEGEES
2. Unscrew knob on side door but do not remove.
These skirts have four wear edges.
3. Pull out on top of door until lip on door clears
brush head.
To use another edge:
4. Push down on door until hooks on bottom of
door are free of scrub head side.
1. Remove each of the scrub deck skirt
assemblies.
5. Pull out on door with a rocking motion to free
idler door from end of brush.
2. Remove the hardware that retains the blade on
each assembly.
6. Pull brush out with a rocking motion to free
brush from drive hub.
3. Flip the blade vertically or horizontally, or both,
and replace hardware.
4. Re-install each scrub deck assembly.
86037660 CHARIOT 11/09/06
4-14
MAINTENANCE-SCRUB DECK - CYLINDRICAL
DUMPING HOPPER
ADJUSTMENT OF INDIVIDUAL BRUSHES
The removable hopper is located behind the rear
scrub brush. If the hopper becomes full, it will not
accept any more debris. Loosen knob on left side
squeegee and swing open. Remove the hopper by
sliding it out from the operator’s left side of the
machine. The hopper can then be dumped from the
top. Flush the hopper clean with running water.
The brush pattern is adjusted from the motor side
only of both brushes.
1. Determine if motor end is to be moved up or
down to balance the pattern.
2. Loosen the 3 allen head screws on the end of
the housing.
SCRUB DECK ADJUSTMENT
Scrub deck adjustment consists of two types of
adjustments. The first is to insure the individual
brushes make the same width pattern end to end.
Any tapered brush pattern should be adjusted out.
The second is to make the pattern of equal width
between front and rear brushes. Unequal patterns
are caused by the scrub deck not being parallel to
the floor. Proper adjustment is obtained when the
contact patterns of the brushes on the floor show
two 1” rectangles the width of the brushes. The
rectangles should be parallel to each other.
TESTING, ADJUSTMENT OF INDIVIDUAL
BRUSHES
1. Move the machine to an unfinished area of floor
to avoid marking finish.
2. With water valve off, lower scrub head to floor.
Allow brushes to run until automatic shut off
occurs. It may be necessary to repeat this step
in the same location until a good mark can be
seen on the floor. This can be accomplished by
touching lightly the throttle pedal to restart the
scrub deck without moving the machine.
3. Loosen the jam nut on the jack screw and rotate
the jack screw to move the motor assembly up
or down as needed.
4. Tighten the 3 allen head screws.
5. Tighten the jam nut on the jack screw.
6. Re-test and readjust as necessary.
LEVELING THE SCRUB HEAD
Leveling the cylindrical head is accomplished by
adjusting the lower links that attach the deck to the
frame. To increase pattern width on rear brush,
loosen lock nuts and shorten the lower links by
screwing the rod into the threaded ends. To
increase pattern width on front brush, lengthen the
lower links by screwing the rod out of the threaded
ends. After adjustment, be sure to tighten lock nuts.
3. Raise the scrub deck and note the brush
patterns on the floor. There should be two
rectangles with parallel sides. If the pattern is
tapered, proceed as follows.
4-15
86037660 CHARIOT 11/09/06
MAINTENANCE-SCRUB DECK - CYLINDRICAL
Do not use a pressure
washer to clean around
the brush motors. Use tap pressure only.
BRUSH MOTOR CARBON BRUSH
REPLACEMENT
TO REPLACE SCRUB BRUSH MOTORS
1. Scribe alignment mark on motor barrel to motor
cap. Remove two bolts.
1. With the scrub deck in the raised position,
disconnect brush motor wiring connector from
harness.
2. Remove end cap from motor.
NOTE: Motors contain two wave washers in
cap. Do not lose these.
2. Remove side squeegee assembly.
3. Release brush from spring tension. Remove
screw connecting brush wire lead to brush
holder. Clean brush holder to insure free
movement.
3. Remove brushes and brush door.
4. Remove aluminum end housing from deck.
5. Separate brush motor with gear box from end
housing.
4. Retract spring and install new brush. Install
connector screw and lead.
5. When all new brushes are installed. Place all in
retracted position, held into brush holder by
spring tension.
6. Reverse to reassemble.
7. Adjust brush levelness as described in earlier
section.
6. Carefully place end cap onto bearing on motor
shaft.
NOTE: Use care to assure wave washer
alignment.
7. With end cap in partially installed position,
release all brushes to contact position with
motor commutator.
NOTE: Failure to insure all brushes are released
will result in motor failure.
8. Reset end cap and realign with scribe marks on
motor barrel. Reinstall the two attach bolts from
cap into base.
9. Maintain alignment between motor barrel base
and cap.
86037660 CHARIOT 11/09/06
4-16
MAINTENANCE-SCRUB DECK - CYLINDRICAL
ACTUATOR SCRUB DECK
REMOVAL/REPLACEMENT
SCRUB DECK ACTUATOR ADJUSTMENT
FOR SAFETY: Before leaving or servicing
machine, stop on a level surface. Turn off
machine.
1. Lower scrub deck.
2. Disconnect spring assembly from actuator slide
link.
3. Remove the clevis pin retaining the top of the
acutator.
4. Remove slide link and actuator as an assembly
by removing the two bolts connecting them to
the deck through the bushings.
5. Either unthread the actuator main lead screw
from the barrel, or remove the two bolts
connecting the barrel to the slide link.
6. Reverse for re-installation.
The actuator will need to be adjusted when
replaced.
To adjust the actuator:
1. While holding actuator barrel to prevent it from
spinning, apply power to the actuator such that it
is fully extended. Positive power to white wire,
and negative/ground to black. Limit switch
within actuator will stop it.
2. Turn barrel out one or more full turns to assure
that when it is retracted it will not bind against
itself.
3. While holding actuator barrel to prevent it from
spinning, apply power to the actuator such that it
is fully retracted. Positive power to black wire,
and negative/ground to white wire. Limit switch
within actuator will stop it.
4. With actuator fully retracted, turn barrel in until it
touches the base of the threaded shaft.
5. At the bottomed out position, turn the barrel out
only enough to allow connection to slide link.
6. Connect actuator.
7. Check travel of actuator during operation.
4-17
86037660 CHARIOT 11/09/06
MAINTENANCE-CIRCUIT PROTECTION
2
1
1.
CIRCUIT BREAKERS (BASIC PANEL
SHOWN)
Circuit breakers interrupt the flow of power in the
event of an electrical overload. When a circuit
breaker is tripped, reset it by pressing the
exposed button. If a circuit breaker continues to
trip, the cause of the electrical overload should
be found and corrected.
2.
FUSE (DELUXE ONLY)
The fuse is a one-time circuit protection device
designed to stop the flow of electrical current in
the event of an electrical overload. If fuse is
blown, it must be replaced.
The fuse is located inside the battery
compartment.
18 Amp. Protects the left scrub
brush motor.
18 Amp. Protects the right scrub
brush motor.
30 Amp. Protects the vacuum
motor (Basic only).
30 Amp. Cylindrical
25 Amp. Disk
Protects the propel motor.
3 Amp. Protects the machine
controls (Basic only).
3 Amp. Protects the pump
(Basic only).
86037660 CHARIOT 11/09/06
4-18
MAINTENANCE-SOLUTION STRAINER & PUMP - DISK MODELS
1
5
2
6
3
4
1. Solution Strainer-Coarse
2. Solution Strainer-Fine
3. Pump
4-19
4. Pump Mounting Plate
5. Solenoid Valve
6. Shut-off Valve
86037660 CHARIOT 01/03/08
MAINTENANCE-SOLUTION STRAINER & PUMP-CYLINDRICAL MODELS
1
2
6
1. Solution Strainer-Coarse
2. Solution Strainer-Fine
3. Pump
3
4
5
4. Solenoid Valve
5. Jets
6. Shut-off Valve
86037660 CHARIOT 01/03/08
4-20
MAINTENANCE-SOLUTION STRAINER & PUMP
1.
3.
SOLUTION STRAINER-COARSE
Located in bottom of tank. The coarse strainer
protects the finer strainer from large debris. If
the fine strainer is clean and the pump and
solenoid valve are not working, then check the
coarse strainer for debris. Drain the solution
tank and clean the coarse strainer. To remove
the strainer, rotate the strainer
counterclockwise. Cleanout the debris from wire
mesh and re-assemble.
2.
The pump is located under the tank on the right
side of machine. The pump delivers solution
from the tank to the scrub deck.
To repair or replace pump:
1. Remove scrub deck skirts, Aqua-Mizer, and
squeegee from machine.
2. Lower scrub deck to gain access to pump
mounting plate.
SOLUTION STRAINER (FINE) AND
SHUT-OFF VALVE
The fine strainer is located in front left corner of
machine on disk models and in right rear corner
of cylindrical models. The fine strainer protects
the pump and solenoid valve from debris. If
there is little or no solution flow to the ground,
first check to make sue the shut-off valve is
open. Next, check the strainer for debris. To
remove the strainer, first turn the shut-off valve
to the off position. Then, turn the bottom part of
the strainer counterclockwise until the bottom is
separated. Clean out the debris from the wire
mesh and re-assemble. Make sure the O-ring
gasket is in place when re-assembled. To
resume flow, turn the shut-off valve to the open
position.
PUMP
3. Remove screw that secures pump mounting
plate to frame.
4. The pump is located under the tank on the
right side of machine. The pump delivers
solution from the tank to the scrub deck. Pull
pump mounting plate forward and down to
expose pump.
5. Reverse steps to install.
4.
PUMP MOUNTING PLATE
See graphic representation on previous page.
5.
SOLENOID VALVE
The solenoid valve is mounted on the front of
the scrub deck, on left side.
The solenoid valve shuts off solution flow to
scrub deck whenever scrubbing stops. To
repair or replace solenoid valve, cut cable ties
that secure it to deck.
PUMP HEAD REPLACEMENT
(86136450)
(PRV NO. 65151)
4-21
VALVE ASM. DIAPHRAGM ASM.
(86235090)
(86137240)
(PRV NO. 84145) (PRV NO. 29188)
86037660 CHARIOT 01/03/08
MAINTENANCE-VACUUM & FLOAT SHUT-OFF
1
2
1.
2.
Recovery tank float shut-off
Vacuum motor
86037660 CHARIOT 11/09/06
4-22
MAINTENANCE-VACUUM & FLOAT SHUT-OFF
RECOVERY TANK FLOAT SHUT-OFF
When water is no longer being vacuumed from
the floor and the vacuum fan is operating, the
ball float has engaged. The vacuum motor will
not vacuum water with recovery tank full. The
recovery tank must be drained.
1.
The float shut-off screen can be cleaned in or
out of the machine.
2.
To clean the float shut-off while it is inside the
machine wipe material off screen then rinse.
Check that the ball is also clean and moves
freely.
3.
4.
FOR SAFETY: before leaving or servicing
machine, stop on a level surface, turn off machine
and disconnect power.
TO REPAIR OR REPLACE VACUUM MOTOR
1.
Remove rear cover from machine.
2.
Remove two screws from top of control
panel and four screws from sides of control
housing.
3.
Slide control housing back from tank to
expose vacuum motor.
4.
To remove the float shut-off, grasp the screen
with one hand and the connected tube with the
other. Tilt and pull the float screen assembly to
pull it off the barb on the tube.
Disconnect electrical connector from the
vacuum motor.
5.
Remove three nuts that secure vacuum
motor retaining plate, remove plate and
vacuum motor.
To install, place one hand on the tube, and then
tilt and push the float screen assembly over the
barb on the tube.
6.
Reverse steps to install. Make sure that
gasket is on vacuum so that vacuum seals
against tank
Vacuum Motor Carbon Brushes
End Cap
Carbon
Brushes
If armature commutator is grooved, extremely pitted or not
concentric, the motor will need to be replaced or sent to a
qualified service center.
Important:
These brushes wear quicker as the length shortens due to
increased heat. Spring inside brush housing will damage
motor if brushes are allowed to wear away completely.
3 [9.5mm]
8
Periodically check the length of the carbon brushes. Replace
both carbon brushes when either is less than 3/8" (9.5mm)
long.
4-23
86037660 CHARIOT 11/09/06
MAINTENANCE-DRIVE MOTOR & BRAKE
1.
2.
3.
Drive motor
Parking brake
Drive chain
86037660 CHARIOT 10/29/08
4-24
MAINTENANCE-DRIVE MOTOR & BRAKE
ELECTRIC PARKING BRAKE ENGAGEMENT
To disengage brake:
FOR SAFETY: Before leaving or servicing
machine, stop on a level surface, turn off
machine and remove key.
Electric Brake Engagement
This machine is equipped with an electric parking
brake.
The brake automatically engages and keeps the
machine from moving whenever the operator steps
off the platform or when emergency stop is engaged.
The brake has a mechanical over-ride that can be
engaged so machine can be pushed or towed
(slowly).
When the mechanical over-ride is engaged the
machine cannot be driven.
1. Mechanical over-ride disengaged
Machine can be driven.
2. Push lever firmly in direction of arrow.
To engage brake:
1. Mechanical over-ride engaged.
Machine can be pushed or towed (slowly).
2. Push lever firmly in direction of arrow
Note: There is an intermediate stop. Make sure
lever is fully in the down position.
4-25
86037660 CHARIOT 10/29/08
MAINTENANCE-DRIVE MOTOR & BRAKE
DRIVE MOTOR CARBON BRUSH REPLACEMENT
5.
Install new brush and reinstall connecting
screw and lead.
Do not use a pressure
washer to clean around
the motors. Use tap pressure only.
6.
When all new brushes are installed. Place all
in retracted position, held into brush holder by
spring tension.
FOR SAFETY: Before leaving or servicing
machine, stop on a level surface, turn off machine
and remove key.
7.
Carefully replace brush cap.
Reinstalling:
10. When replacing the hex hub, use a small pin
or screw to help align the holes.
1. Disconnect batteries from machine.
2. Disconnect the electrical connection to the traction
motor.
BRAKE REMOVAL
(Must be done to access carbon brushes)
3. Remove 4 mounting screws and remove brake.
11. Drive the pin into the hub and make sure it is
flush to the hex surface. The brake will not fit
on the hub if the roll pin is protruding from the
hub.
12. Replace the hub and use Lock-Tite on the
screws.
4. Drive roll pin out of the hex hub enough to allow
hex hub to slide off shaft. It is recommended that
the roll pin be left partially in the hex hub.
5. Remove brush cap.
ROLL PIN
HEX HUB
SMALL PIN OR SCREW
6. Release brush from spring tension. Remove
screw connecting brush wire lead to brush holder.
Clean brush holder to insure free movement.
86037660 CHARIOT 11/09/06
4-26
MAINTENANCE-BAG REPLACEMENT
REMOVING BAG
REPLACING BAG
1. Disconnect batteries and make sure parking brake
is not overridden.
1. Install mandrel in bottom of bag.
2. Under left front side of machine loosen hose
clamp on recovery dump hose. Do not remove
hose.
2. Place new bag in tank making sure hole for
strainer basket is oriented properly.
3. Remove Dome and set aside
4. Remove Float cage, loosen screw on elbow and
remove elbow.
3. Angle mandrel and bag into tank fitting toward
front of machine. Push mandrel into fitting
until it bottoms out.
5. Remove the eight screws and nuts holding the bag
clamps and set aside.
4. Attach bag to top of machine by rolling edge of
bag over clamp strips.
6. Remove clamps and set aside.
5. Replace elbow and float cage.
7. Pull mandrel from bottom of tank. Access can
either be from the dirty water side or the clean
water side or both. When replacing bag with new
one be sure to save mandrel.
6. Tighten clamp on bottom of machine.
4-27
86037660 CHARIOT 11/09/06
MAINTENANCE-TRANSPORTING
PREPARATION FOR LOADING /UNLOADING
TRAILER
PUSHING MACHINE
The machine may be pushed for short distances at
speeds not to exceed 5 mph. Be careful to avoid
damaging machine. The machine may be pushed by
hand from the rear.
NOTE: To avoid damage caused by regenerative
voltage, disconnect traction motor before towing or
pushing machine.
MACHINE TIE-DOWNS
There are two tie points located at front and each side
of foot box frame and two at the front side of frame.
Tie-down devices must be of the proper type and
strength. The combined strength of all tie-downs must
be strong enough to lift two times the weight of the
machine. Tie-downs must be positioned to prevent
the machine from moving forward, backward, or either
side to side. Use all four corners of the machine with
the tie-downs running out opposite directions. Tiedowns must be attached to the transporting vehicle
securely.
Before loading or unloading machine from trailer,
remove squeegee, scrub deck, side skirts or side
squeegees, Aqua-Mizers and scrub brushes
(pads) to eliminate interference with tie-downs.
Scrub head must be in the up position before
loading.
NOTE: When transporting the machine on a trailer
or in a truck, in addition to using tie-downs, be
sure to set the parking brake, and block the tires to
prevent the machine from rolling.
TIE DOWN POINTS
86037660 CHARIOT 11/09/06
4-28
MACHINE TROUBLESHOOTING
PROBLEM
No power to machine
Little or no propel
ERROR
CODE
DELUXE
CAUSE
Battery disconnected
Emergency shut-off activated
Check all battery cable
connections
Reset
Battery cables corroded
Main fuse blown (Deluxe Only)
Clean connections
Replace fuse
Faulty key switch
Replace switch
Low battery charge
Charge batteries
Machine turned on with pedal not in
neutral position
Allow pedal to return to
neutral.
Restart
Reset circuit breaker
Decrease brush pressure
Allow cool down period
Check wires and
connections from controller
to motor
Check wires and
connections from throttle to
LCD controller and
potentiometer resistance
Check wires, connections
and switch
Check wires, connections
and switch
Check wires, connections
and switch
Disengage brake over-ride
Tripped circuit breaker
Wheels spin
Controller overheated
Loose motor connection
7802/7801
7800
Faulty throttle circuit or potentiometer
Faulty drive reset circuit or switch
Faulty operator presence pedal
circuit or switch
Faulty platform circuit or switch
Brake over-ride engaged
Machine does not change
speeds
Forward speed only
Reverse speed only
Poor or no water pickup
Faulty brake circuit or over-ride
switch
Faulty speed control circuit or switch
0814
Faulty forward/reverse switch
Check wires, connections
and switch
Check wires, connections
and switch
Replace switch
Squeegee out of adjustment
Adjust squeegee
Debris caught on squeegee
Remove debris
Worn squeegee blades
Rotate or replace
squeegee blades
Clear obstruction from
hose
Reconnect vacuum hose
Vacuum hose clogged
Vacuum hose disconnected from
squeegee or recovery tank dome
Recovery tank float system dirty
Recovery tank not sealed
Float-ball shut-off engaged Tank full
Foam filling recovery tank
4-29
SOLUTION
86037660 CHARIOT 11/09/06
Clean float system
Place recovery tank dome
on tank. Replace
damaged gaskets
Empty recovery tank
Empty recovery tank. Use
less or different detergent.
Use defoamer.
MACHINE TROUBLESHOOTING
PROBLEM
Vacuum motor does not run, or
runs slowly
CAUSE
ERROR
CODE
DELUXE
Circuit breaker tripped (Basic)
Faulty vacuum circuit or switch
SOLUTION
Reset circuit breaker
7700
Squeegee will not go up/down
Faulty circuit or actuator
(Deluxe)
Faulty cables or pulleys
Poor scrubbing performance
Debris caught in scrub brushes
Check wires, connections
and switch
Replace brushes, check
commutator
Check wires, connectors
and actuator
Repair/replace cables or
pulleys
Remove debris
Worn brushes or pads
Replace brushes or pads
Improper detergent, brush or
pad used
Low scrub brush down pressure
Contact equipment or
application specialists
Increase brush pressure
Low battery charge
Charge batteries
Solution tank empty
Fill solution tank
Solution flow turned off or set
too low
Solution strainer plugged
Turn on or increase flow
setting
Clean solution strainer
Solution system plumbing
obstructed
Pump obstructed
Clear obstruction from
plumbing
Clean or replace pump
Solution solenoid valve
obstructed or stuck
Solution shut-off valve is closed
Clean or replace valve
Faulty pump circuit or pump
Check wiring, connections,
control broad (Basic) and
pump.
Check solenoid valve
Worn vacuum motor brushes
Little or no solution flow to the floor
Open shut-off valve
Faulty solenoid
Brush motors do not run, or run
slowly
Circuit breaker(s) tripped
7600
Low battery charge
Fault brush circuit or motor
Charge battery
7600
Worn brush motor brushes
Scrub deck will not go down/up
Scrub deck goes down, then raises
Error code not listed is displayed
Actuator circuit breaker tripped
(Basic)
Faulty actuator circuit or
actuator
No brushes or pad drivers on
machine
Controller detects electrical
problem
86037660 CHARIOT 01/03/08
Reset circuit beaker(s)
9000
Check wires, connections
and motor
Replace brushes, check
commutator
Reset breaker
Check wires, connections
and actuator
Install brushes or pad
drivers
Contact service technician
4-30
MACHINE TROUBLESHOOTING – DELUXE CONTROLLER FAULT CODES
ERROR
CODE
DELUXE
PROBLEM
None
LCD display on, but incomplete
0A01
0204
Power down error
Memory corrupt
All 080_ codes
Throttle wiring
All 140 _ Codes
All 310_ Codes
Possible short circuit of motors, auxiliary
outputs (headlight, recycle pump, or backup alarm), wiring or damaged controller
7500
LCD module communications timeout
7501
LCD module settings corrupt
All 760_ Codes
Brush motor or brush circuit fault
All 770_ Codes
Vacuum motor or vacuum circuit fault
7800
Traction motor open circuit fault
7801
Traction motor overcurrent error
7802
All 790_ Codes
Traction motor in power foldback state
Emergency stop error
9000
Brush current requirement not satisfied
4-31
SOLUTION
Disconnect batteries and wait 1 minute before
re-applying power.
Disconnect batteries and wait 1 minute before
re-applying power.
Replace controller.
Check for short or open circuits in throttle
wiring.
Check for short circuit between B+ and
traction output.
Check for short circuits. If code is present
after short circuits are repaired, replace
controller.
Wiring fault on 6-way serial link between
controller and display.
Disconnect batteries and wait 1 minute before
re-applying power.
Check for short or open circuits in brush
motors or wiring.
Check for short or open circuits in vacuum
motor(s) or wiring.
Check for open circuit on propel motor or
wiring.
Check for short circuit on propel motor or
wiring.
Propel motor current has exceeded current
limit for the foldback time.
E-stop input active or wiring fault.
Check that brushes or pads are installed.
Check for open circuit in scrub lift actuator,
circuit breaker or wiring.
86037660 CHARIOT 05/27/08
MACHINE TROUBLESHOOTING- CONTROLLER FAULT CODES
PROPEL CIRCUIT BOARD TROUBLESHOOTING
Curtis 1228 LED DIAGNOSTICS- Basic and Cylindrical
During normal operation, with no faults present, the status LED is steadily on.
If the controller detects a fault, the status LED provides two types of information.
First, it displays a slow flash (2 Hz) or a fast flash (4 Hz) to indicate the
severity of the fault. Slow-flash faults are self-clearing; as soon as the fault is
corrected, the vehicle will operate normally. Fast-flash faults (“.” in Table 2) are
considered to be more serious in nature and require that the key switch be cycled
to resume operation after the fault is corrected.
After the severity indication has been active for 10 seconds, the status
LED flashes a 2-digit fault identification code continuously until the fault is
corrected. For example, code “1,4”—low battery voltage—appears as: one LED flash, followed by a pause, then 4 LED
flashes, and then repeats.
LED
CODE
1,1
1,2
PROGRAMMER LCD
DISPLAY
THERMAL CUTBACK
THROTTLE FAULT 1
EXPLANATION
POSSIBLE CAUSE
over-/undertemperature cutback
1. Temperature >92°C or < -25°C.
2. Excessive load on vehicle.
3. Operation in extreme environments.
4. Electromagnetic brake not releasing.
throttle fault
1. Throttle input wire open or shorted.
2. Throttle pot defective.
3. Wrong throttle type selected.
1,3
SPD LIMIT POT FAULT
speed limit pot fault
1. Speed limit pot wire(s) broken or shorted.
2. Broken speed limit pot.
1,4
LOW BATTERY VOLTAGE
battery voltage too low
1. Battery voltage <17 volts.
2. Bad connection at battery or controller.
1,5
OVERVOLTAGE
battery voltage too high
1. Battery voltage >36 volts.
2. Vehicle operating with charger attached.
3. Intermittent battery connection.
2,1
MAIN OFF FAULT
main contactor driver
Off fault
1. Main contactor driver failed open.
2,3
MAIN CONT FLTS
main contactor fault
1. Main contactor welded or stuck open.
2. Main contactor driver fault.
3. Brake coil resistance too high.
2,4
MAIN ON FAULT
main contactor driver
On fault
1. Main contactor driver failed closed.
86037660 CHARIOT 05/27/08
4-26
4-32
MACHINE TROUBLESHOOTING- CONTROLLER FAULT CODES
LED
CODE
PROGRAMMER LCD
DISPLAY
EXPLANATION
POSSIBLE CAUSE
3,1
PROC/WIRING FAULT
HPD fault present for
>10 sec.
1. Misadjusted throttle.
2. Broken throttle pot or throttle mechanism.
3,2
BRAKE ON FAULT
brake On fault
1. Electromagnetic brake driver shorted.
2. Electromagnetic brake coil open.
3,3
PRECHARGE FAULT
precharge fault
1. Low battery voltage.
2. KSI and throttle turned on at same time.
3,4
BRAKE OFF FAULT
brake Off fault
1. Electromagnetic brake driver open.
2. Electromagnetic brake coil shorted.
3,5
HPD
HPD (High Pedal
Disable) fault
1. Improper sequence of throttle and KSI,
push, or inhibit inputs.
2. Misadjusted throttle pot.
4,1
CURRENT SENSE FAULT
current sense fault
1. Short in motor or in motor wiring.
2. Controller failure. *
4,2
HW FAILSAFE
motor voltage fault
(hardware
1. Motor voltage does not correspond to throttle
request.
2. Short in motor or in motor wiring.
3. Controller failure. *
4,3
EEPROM FAULT
EEPROM fault
1. EEPROM failure or fault.
4,4
POWER SECTION FAULT
power section fault
1. EEPROM failure or fault.
2. Short in motor or in motor wiring.
3. Controller failure.
4-33
86037660 CHARIOT 05/27/08
PARTS
86037660 CHARIOT 11/09/06
BUMPER
1
2
7
6
8
10
7 10 9
3
11
5
1
4
5-1
86037660 CHARIOT 11/09/06
BUMPER
REF
1
2
3
4
5
6
7
8
9
10
11
PART NO.
86276890
86007070
86063230
86063240
86071020
86270830
86010670
86070730
86197040
86279130
86251750
PRV NO.
70752
70849
140813
140814
140783
57023
87029
140729
57264
87083
67602
QTY
6
2
1
1
1
4
4
2
4
4
2
DESCRIPTION
SCR, 5/16-18X3/4 PTHMS SS
SCR, 5/16-18X1.00 PPHMS SS
BUMPER, LEFT
BUMPER, RIGHT
BRKT, FRONT BUMPER
NUT, 5/16-18 HEX NYLOCK SS
WASHER, 5/16 FLAT SS
BRKT, BUMPER MOUNT, SIDE
NUT, 5/16-18 HEX ACORN PLTD
WASHER, 5/16 SPLIT LOCK PLTD
RISER, BUMPER
86037660 CHARIOT 11/09/06
SERIAL NO.
FROM
NOTES:
5-2
CONTROL PANEL-BASIC-CYLINDRICAL
2
7
6
1
8
5
43
42
3
10
41
37
38
9
4
11
40
12
15
44
13
36
17
39
28
28
14
35
15
26
27A
27B
33
45
16
25A
25B
26
18
34
24
22
17
45
19
23
17
22
22
29
30
22
31
46
20
5-3
21
32
17
86037660 CHARIOT 06/25/07
CONTROL PANEL-BASIC-CYLINDRICAL
REF
PART NO.
PRV NO.
QTY
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25A
25B
26
86007210
86246980
86008900
86002010
86005560
86007180
86257110
86257280
86007190
86007140
86257140
86273820
86277480
86008760
86005810
86070720
86273990
86078150
86271840
86005710
86003250
86255900
86251410
86005530
86001910
86001920
86002000
72165
54201
80845
14942
54199
72160
72189
81371
72161
72130
72196
70019
70850
80682
57245
140728
70067
61475
57285
57105
27944
73538
67506
54154
14606
14607
14717
1
1
2
1
1
1
1
1
1
1
1
2
3
1
6
1
8
1
3
2
1
8
1
1
1
1
2
SWITCH, DPDT 3-POSITION ROCKER
METER, 0-50 AMP DC
BOOT, SEAL-PUSH BUTTON 7/16-28
BOOT, 3/8 CIRCUIT BREAKER
METER, 36V LED BATTERY
SWITCH, EMERGENCY STOP
SWITCH, 4P3T FIXED POS ROCKER
SWITCH, PUSH BUTTON
SWITCH KEY DPSTN
SWITCH, SPST 2-POSITION ROCKER
SWITCH, RESET PB ROUND
SCR, 1/4-20 X 1.25 HHCS
SCR, 5/16-18 X 1/2 PTHMS SS
CONN, 175 DCA GRY W/O TERMS
NUT, 1/4-20 HEX NYLOCK SS
BRKT, BATT CONN, BASIC
SCR, 6-32 X 3/8 PPHMS
PANEL, BASIC
NUT, 5/16-18 HEX NYLOCK THIN SS
NUT, 1/4-20 HEX W/STAR WASHER
CIRCUIT BOARD, SOL FLOAT WIRED
STANDOFF, 6-32 X 5/8 HEX NYL
RELAY, 15A 36V MINI
METER, 12-48 VDC LED HOUR
BREAKER, 30A 50VDC CIRCUIT
BREAKER, 25A 50VDC CIRCUIT
BREAKER, 3 AMP
27A
86002760
270092
1
CONTROLLER, CHAIN DRIVE BASIC
27B
86027740
27911
1
CONTROLLER, GEAR DRIVE BASIC
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
86005700
86271790
86276250
86008190
86229770
86001730
86001910
86279130
86271120
86223740
86006370
86010670
86249290
86237830
86242110
86002010
86006310
86279300
86010630
57104
57256
70615
73988
140805
140804
14606
87083
57125
70872
67315
87029
62283
35264
48088
14942
66335
87134
87013
10
2
2
1
1
2
1
4
4
4
2
4
1
1
1
3
1
4
2
NUT, 10-32 W/STAR WASHER PLTD
NUT, 6-32 HEX BRASS
SCR, 6-32 X 3/8 SRHMS BR
SHUNT, DC AMM. 15 AMP, 50 MV
BLOCK, SHUNT MOUNT
BREAKER, 18A 250VAC, 50VDC
BREAKER, 30A 50VDC CIRCUIT
WASHER, 5/16 SPLIT LOCK PLTD
NUT, 5/16-18 BRASS
SCR, 1/4-20 X .59 PPHMS SS C
RELAY, 36VDC 100AMP HVY DUTY
WASHER, 5/16 FLAT SS
PLATE, METER RETAINING
GASKET, AMP METER
KNOB, .90 OD X .25 COLLET
BOOT, 3/8 CIRCUIT BREAKER
POTENTIOMETER, 50K OHMS
WASHER, #6 LOCK
WASHER, 1/4 ID X 5/8 OD SS
SERIAL NO.
FROM
*(1)
*(16)
NOTES:
WAS 14607, 25A
CYLINDRICAL ONLY
FOR 29269-DRIVE
UNIT (CHAIN)
FOR 29276- DRIVE
UNIT (GEAR)
*SEE SERIAL NUMBER PAGE.
86037660 CHARIOT 09/06/07
5-4
CONTROL PANEL-DELUXE
1
3
2
33
4
34
35
1
5
6
36
32
31
8
7
9
21
10
30
11
26A
26B
12
40
37
29
22
25
14
13
28
15
27
38
SUPPLED WITH
CONTROLLER
39
24
20
16
18
23
17
18
19
5-5
86037660 CHARIOT 02/21/06
CONTROL PANEL-DELUXE
REF
PART NO.
PRV NO.
QTY
DESCRIPTION
1
86007520
730142
3
2
86007180
72160
2
SWITCH, EMERGENCY STOP
3
86007190
72161
1
SWITCH KEY DPST
4
86007140
72130
1
SWITCH, SPST 2-POSITION ROCKER
5
86257140
72196
2
SWITCH, RESET PB ROUND
6
86257280
81371
1
SWITCH, PUSH BUTTON
7
86273820
70019
2
SCR, 1/4-20 X 1.25 HHCS
8
86273830
70020
2
SCR, 1/4-20 X 1/2 HHCS SS
SERIAL NO.
FROM
NOTES:
SWITCH, SPDT 3-POSITION MOM
9
86010780
87162
2
WASHER, 1/4 SPLIT LOCK PLTD
10
86277480
70850
3
SCR, 5/16-18 X 1/2 PTHMS SS
11
86070670
140722
1
BRKT, BATTERY CONNECTOR
12
86008760
80682
1
CONN, 175 DCA GRY W/O TERMS
13
86005810
57245
2
NUT, 1/4-20 HEX NYLOCK SS
14
86271840
57285
3
NUT, 5/16-18 HEX NYLOCK THIN SS
15
86255910
73659
2
STANDOFF, 1/4-20 X 1.0 HEX INS
16
86006850
70393
2
SET SCR, 1/4-20 X 1.25L
17
86008790
80687
1
FUSE, 125 AMP
18
86010630
87013
6
WASHER, 1/4 ID X 5/8 OD SS
19
86008920
80889
2
BOOT, RUBBER TERM. ISOLATOR
20
86005710
57105
4
NUT, 1/4-20 HEX W/STAR WASHER
21
86274410
70195
2
SCR, 10-32 X 1.25 PPHMS SS
22
86078160
61476
1
PANEL, DELUXE
23
86255900
73538
2
STANDOFF, 6-32 X 5/8 HEX NYL
24
86251410
67506
1
RELAY, 15A 36V MINI
25
86270990
57090
2
NUT, 10-32 HEX NYLOCK SS
26A
86002770
270095
1
CONTROLLER, CHAIN DRIVE DELUXE
26B
86292580
-
1
CONTROLLER, GEAR DRIVE DELUXE
27
86271910
57295
2
NUT, 5/16-18 FLEXLOCK
28
86010670
87029
2
WASHER, 5/16 FLAT SS
29
86068850
140219
2
BRKT, CABLE ATTACH
30
86001730
140804
2
BREAKER, 18A 250VAC, 50VDC
31
86270920
57049
2
NUT, 6-32 HEX NYLOCK SS
32
86005570
54200
1
MODULE, LCD DELUXE
33
86007480
730124
1
SWITCH ASM, SEALED PUSHBUTTON
34
86002010
14942
2
BOOT, 3/8 CIRCUIT BREAKER
35
86257130
72195
1
SWITCH, ON –TOUCH PB ROUND
36
86001260
140218
1
BOOT, DB 3/8-27 UNS 2B
*(11)
WAS 80845
37
86001950
14666
1
BREAKER, 30A W/AUX CONTACT
*(11)
WAS 14606
38
86279300
87134
2
WASHER, #6 LOCK
39
86273990
70067
2
SCR, 6-32 X 3/8 PPHMS
40
86275760
70540
2
SCR, 5/16-18 X 1 HHCS GR8 PLTD
FOR 29269
DRIVE UNIT,
CHAIN
FOR 29276
DRIVE UNIT,
GEAR
*SEE SERIAL NUMBER PAGE.
86037660 CHARIOT 02/21/09
5-6
CONTROL PANEL HOUSING
2
3
3
1
6
5
11
10
4
7
9
8
5-7
86037660 CHARIOT 11/09/06
CONTROL PANEL HOUSING
REF
1
2
3
4
5
6
7
8
9
10
11
PART NO.
86005810
86290540
86277480
86070710
86237900
86031730
86070700
86279750
86089650
86277420
86010630
PRV NO.
57245
70850
140726
35278
270084
140725
87252
78524
70841
87013
QTY
4
6
6
1
3
1
1
4
4
4
4
DESCRIPTION
NUT, 1/4-20 HEX NYLOCK SS
SCR, 10-32 X 1/2 TORX SS BLK NP
SCR, 5/16-18 X1/2 PTHMS SS
BRKT, LEFT CONSOLE MOUNT
GASKET, .125 X .25W X 23L
CONSOLE
BRKT, RIHGT CONSOLE MOUNT
WASHER, RET, PUSHNUT, 5/16 BOLT
TUBE, 5/8 OD X .357 ID X 1.57
SCR, 5/16-18 X 2.5 PTHMS SS
WASHER, 1/4 ID X 5/8 OD SS
86037660 CHARIOT 02/20/07
SERIAL NO.
FROM
NOTES:
5-8
DECAL
4
7
5
3
1
2
9
5-9
86037660 CHARIOT 01/05/09
DECAL
REF
1
2
3
4A
4B
5A
5B
6
7
8
PART NO.
86004970
86244740
86244750
86244200
86244180
86244190
86244170
OPEN
86243990
OPEN
PRV NO.
50990
501222
501223
500883
500881
500882
500880
QTY
1
1
1
1
1
1
1
DESCRIPTION
LABEL, WINDSOR LOGO DOMED
DECAL, CHARIOT, ISCRUB RT
DECAL, CHARIOT, ISCRUB LT
LABEL, PANEL BASIC RIGHT
LABEL, PANEL DLX RIGHT
LABEL, PANEL BASIC LEFT
LABEL, PANEL DLX LEFT
500780
1
LABEL, COVER PANEL
9
86298970
-
1
LABEL, CLEAN BRUSHES AND DECK
SERIAL NO.
FROM
NOTES:
WAS 500884
WAS 500885
CYLINDRICAL
ONLY
NOTE: See “SAFETY LABEL LOCATION” page for safety label information.
86037660 CHARIOT 01/06/09
5-10
FRAME-LOWER
2B
1
3
2A
4
5
4
17
6
7
16
8
8
10
9
8
11
8
15
4
4
8
21
13
8
18
22
14
19
20
8
13
12
5-11
4
14
86037660 CHARIOT 03/04/08
FRAME-LOWER
REF
1
PART NO.
86070750
PRV NO.
140731
QTY
1
DESCRIPTION
BRKT, TIP BAR LEFT
2A
86071130
140812
1
BRKT, TIP BRACE, LEFT, REAR
2B
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
86303720
86070760
86276070
86092500
86197040
86279130
86270830
86071120
86071430
86070740
86277470
86064300
86010670
86091420
86088760
86088750
86079290
86010630
86271870
86276950
86079320
140733
70593
34428
57264
87083
57023
140811
140863
140730
70848
140790
87029
05251
75458
75457
620097
87013
57290
70772
620101
1
1
16
1
4
4
16
1
1
1
4
2
4
1
1
1
2
4
4
4
2
BRKT, BRACE, LT. REAR SOL
BRKT, TIP BRACE, LEFT
SCR, 5/16-18 X 3/4 CARRIAGE SS
FRAME, MAIN
NUT, 5/16-18 HEX ACORN PLTD
WASHER, 5/16 SPLIT LOCK PLTD
NUT, 5/16-18 HEX NYLOCK SS
BRKT, TIP BRACE, LEFT, REAR
BRKT, BRACE RIGHT FRONT
BRKT, LINKAGE, RIGHT
SCR, 5/16-18 X 1.5 CARRIAGE SS
PAD, TIPPING BAR
WASHER, 5/16 FLAT SS
AXLE, REAR WELDMENT
TRAY, SLIDE, LEFT
TRAY, SLIDE, RIGHT
PLATE, REAR COVER ADJ
WASHER, 1/4 ID X 5/8 OD SS
NUT, 1/4-20 HEX NYLOCK THIN SS
SCR, 1/4-20 X 3/4 CARRIAGE SS
PLATE, PAD RETAINER
SERIAL NO.
FROM
NOTES:
CYLINDRICAL
ONLY
DISK ONLY
*(6)
*(6)
*(6)
*(6)
*(7)
* SEE SERIAL NUMBER PAGE.
** CALL MANUFACTURER FOR SERIAL NUMBER
86037660 CHARIOT 01/03/08
5-12
FRAME-UPPER
2
4
3
1
2
2
1
5
3
6
1
3
2
2
SEE SQUEEGE
LIFT GROUPS
3
7
5-13
86037660 CHARIOT 11/09/06
FRAME-UPPER
REF
1
2
3
4
5
6
7
PART NO.
86010670
86270830
86276070
86091750
86073500
86083080
86277460
PRV NO.
87029
57023
70593
140727
270090
66437
70847
QTY
5
8
7
1
1
1
1
DESCRIPTION
WASHER, 5/16 FLAT SS
NUT, 5-16-18 HEX NYLOCK SS
SCR, 5-16-18 X 3/4 CARRIAGE SS
BRKT, HORIZ ELECT
BRKT, SIDE CHANNEL L
PLATE, VERT BEARING SUPPORT
SCR, 5/16-18 X 5/8 BSHCS SS
86037660 CHARIOT 11/09/06
SERIAL NO.
FROM
NOTES:
5-14
PEDAL PLATFORM
1
2
9
30
28
3
10
4
11
12
5 6
31
8
9
23
22
27
26
25
24
20
10
13
11
12
15
29
14
17
7
16
17
32
18
19
21
20
17
5-15
86037660 CHARIOT 10/04/07
PEDAL PLATFORM
REF
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
PART NO.
86217650
86222700
86216380
86007110
86279720
86272040
86223580
86222520
86277390
86233170
86279730
86277380
86222510
86254970
86222780
86277360
86274340
86224360
86222810
86279140
86288720
86250280
86222790
86278060
86224350
86277370
86221850
86218810
86316310
86264920
86224750
86223260
PRV NO.
34432
34429
140713
72123
87248
57503
67502
34431
70836
20054
87249
70835
34430
730304
620047
70833
70179
730325
620050
87085
57277
66135
620048
70759
730305
70834
34433
23717
57086
27049
73993
66085
QTY
1
1
2
2
4
4
2
1
4
3
4
4
1
2
2
2
11
2
1
9
2
1
1
2
1
1
1
1
1
1
1
1
DESCRIPTION
DIVIDER
PLATFORM
BUSHING, 8MM X 10LG CLY
SWITCH, 25A SPST 125-250V SNAP
WASHER, M4 INT STAR
NUT, M3.5 X 2.8 HEX
ROD, PIVOT, 8.5MM X 77
PEDAL, BRAKE
SCR, M3.5 X 38 PHMS
CLAMP, 3/8 NYLON UL/CSA
WASHER, M5 INT STAR
SCR, M4.8 X 16 PHTF
PEDAL, THROTTLE
SPRING, COMP 18MM OD X 83 X 2
PLATE, PIVOT
SCR, M6 X 10 PH
SCR, M6 X 16 PH
SPACER 12.7MM ID X 2.78W X 6L
PLATE, COVER
WASHER, M6 SPLIT LOCK DIN127B
NUT, M6 NYLOCK PLATED
POTENTIOMETER, 5K OHMS
PLATE, THROTTLE
SET SCR, M4 X 4MM NP
SPACER, 8MM 16L
SCR, M5 X 30 SHCS
LINK, THROTTLE
HARNESS, TWISTER PEDAL
NUT, M5 HEX
CABLE TIE, 7” UL/CSA
SPRING, COMP, .480D X .91
PLUNGER, PLATFORM SWITCH
SERIAL NO.
FROM
NOTES:
*(16)
*(16)
NOTE: Complete platform assembly is available, Part No. 86028310
*SEE SERIAL NUMBER PAGE.
86037660 CHARIOT 11/09/06
5-16
PEDAL PLATFORM
2
3
17
16
6
18
6
14
12
19
9
7
20
4
1
8
5
15
11
8
14
13
12
5
11
10
5-17
86037660 CHARIOT 11/09/06
PEDAL PLATFORM
REF
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
PART NO.
86277430
86274690
86264920
86231070
86010670
86259430
86010770
86270830
86256470
86005810
86010810
86064480
86286580
86007780
86279760
86259440
86271190
86248920
86278850
86008680
PRV NO.
70843
70258
27049
730328
87029
87485
87143
57023
70852
57245
87191
629993
47479
73576
87256
87486
57142
66487
80613
80607
QTY
1
2
3
2
5
4
2
4
2
1
2
1
1
1
2
2
2
1
2
1
DESCRIPTION
SCR, 1/4-20 X 3.00 SHCS
SCR, 5/16-18 X 1.5 HHCS GR5PLT
CABLE TIE, 7” UL/CSA
BUMPER, 1 X 1.375 RUBBER
WASHER, 5/16 FLAT SS
M12 FLAT WASHER
WASHER, 7/16ID X1D.08 FLT SS
NUT, 5/16-18 HEX NYLOCK SS
STUB AXLE, M12-1.75 X 45MM
NUT, 1/4-20 HEX NYLOCK SS
WASHER, 1/4” IDX1.0OD FLAT SS
PLATE, SWITCH BASE
SPACER, ACTUATOR SWITCH
SPRING, COMP .60D X2.0L X .045W
WASHER, 1/4 LOCK HICOLLAR PLT
WASHER, M12 SPRING LOCK
NUT, M12 X 1.75 HEX DIN934 PLT
PIN, CLEVIS 1/2 X 2.25
WASHER, .506 ID X .94D X .064 NYL
COTTER, 1/2” RING
SERIAL NO.
FROM
NOTES:
WAS 730334
*(16)
*(16)
*(16)
*SEE SERIAL NUMBER PAGE.
86037660 CHARIOT 11/09/06
5-18
REAR COVER
21
23 18
20
22 18
14
13
1
10
2
3
9
19
18
3
2
11
12
15
16
9
8
7
6
5-19
5
17A
17B
17C
86037660 CHARIOT 04/16/09
4A
4B
REAR COVER
REF
PART NO.
PRV NO.
QTY
DESCRIPTION
1
2
3
4A
4B
5
6
7
8
9
10
11
12
13
14
15
16
17A
17B
17C
18
19
20
21
22
23
86276780
86279130
86010670
86031790
86031780
86005860
86228980
86275870
86242140
86010770
86248380
86005630
86071030
86010780
86271940
86006560
86066940
86324660
86324320
86324740
86324640
86324760
86010630
86324340
86005810
86324650
70728
87083
87029
270701
270082
57273
09152
70556
72193
87143
66433
57022
140786
87162
57299
70083
140891
87013
57245
-
3
5
5
1
1
2
2
2
1
2
1
1
1
2
2
2
1
1
1
1
1
1
2
1
2
1
SCR, 5/16-18 X 3/4 HHCS SS
WASHER, 5/16 SPLIT LOCK PLTD
WASHER, 5/16 FLAT SS
COVER, REAR, BASIC
COVER, REAR, DELUXE
NUT, 1/4-20 X 12MM HEX BARREL
BEARING FLANGED .377ID X .505OD
SCR, 1/4-20 X 1.5” PPHMS SS
KNOB, 3/8-16 X 1.5
WASHER, 7/16ID X 1D X .08FLT SS
PAD, FLAT LEANING
NUT, 3/8-16 HEX NYLOCK THIN SS
BRKT, ASSEMBLY, REAR COVER
WASHER, 1/4 SPLIT LOCK
NUT, 1/4-20 ACORN SS
SCR, 5/16-18 X 1 HHCS SS
BAR, COVER
REAR COVER, BASIC
REAR COVER, DELUXE
REAR COVER, ORG, DELUXE
HANDLE, CAM LATCH
PLATE, COVER LATCH
WASHER, 1/4 ID X 5/8 OD SS
BRKT, REAR COVER
NUT, 1/4-20 HEX NYLOCK SS
PAWL, HANDLE
SERIAL NO.
FROM
NOTES:
WAS 70697
*(34)
*(34)
*(34)
*(34)
*(34)
*(34)
*(34)
*(34)
*(34)
*See Serial Number Page
86037660 CHARIOT 04/16/09
5-20
SCRUB BRUSH/PAD DRIVER
7
5
6
9
4
8
7
5
6
9
4
8
2A
2B
2C
2D
1
5
3
10A
10B
10C
10D
5-21
86037660 CHARIOT 11/09/06
SCRUB BRUSH/PAD DRIVER
REF
1
2A
2B
2C
2D
3
4
5
6
7
8
9
10A
10B
10C
10D
PART NO.
86000170
86000180
86000190
86000200
86283820
86005070
86276590
86276580
86276600
86007910
86007280
86005940
86283890
86283900
86283910
86283920
PRV NO.
02400
02401
02402
02404
02405
51284
70695
70694
70696
73817
730011
62852
02500
02501
02502
02503
QTY
2
2
2
2
2
1
3
1
3
1
1
1
2
2
2
2
DESCRIPTION
PAD DRIVER, 12” SD
BRUSH, 12” POLYPROPYLENE SD
BRUSH, 12” NYLON SD
BRUSH, 12” MILD GRIT SD
BRUSH, 12” SUPER AGG SD
LOCK, PAD CENTER SNAP, TWO STEP
SCR, #12 X 1 PPHSMS SS
SCR, 8-32 X 3/4 PTHMS
SCR, #10 X 3/4 PTHSMS SS
SPRING, EXT .31 D X 2.0 L X .03 W SS
SOCKET, DRIVE BRUSH
PLATE, BRUSH RELEASE
BRUSH, 24” CYL, H-POLYP
BRUSH, 24” CYL, H-NYLON
BRUSH, 24” CYL, STCD GRIT
BRUSH, 24” CYL, SUP AGR
86037660 CHARIOT 11/09/06
SERIAL NO.
FROM
NOTES:
5-22
SCRUB DECK – DISK
20
19
19
1
20
2
18
3
FROM
PUMP
8
4
8
17
5
16
15
8
9
14
10
11
12
13
5-23
86037660 CHARIOT 05/11/07
6
7
SCRUB DECK – DISK
REF
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
PART NO.
86281100
86003580
86005490
86216200
86004810
86093990
86010790
86276970
86264920
86010600
86003460
86136820
86003420
86279630
86279130
86007020
86279530
86271830
86233150
86004470
86281310
86002830
86264940
PRV NO.
39274
34327
53808
14739
48040
730330
87163
70774
27049
84199
29260
47395
29220
87212
87083
70673
87173
57283
20042
40043
39326
27196
27051
QTY
1
1
2
2
1
8
8
6
1
2
2
2
2
2
2
1
2
2
2
2
DESCRIPTION
HOSE, 1/2ID WIRE BOUND X 8”
FITTING, 1/2”X3/8”X3/8” RED
MOTOR ASM, 36VDC300RPM GEAR
BRUSH SET MOTOR 53808
KEY, 1/4 SQ X 1.00
SCRUBDECK, 24IN
WASHER, 3/8 SPLIT LOCK PLTD
SCR, 3/8-16 X 3/4 HHCS SS
CABLE TIE, 7” UL/CSA
VALVE, SOLENOID, 36VDC, 1/2 BARB
DIAPHRAGM, SRVC PART SLND
SERVICE SLND SPRG KIT
DRIVER, BRUSH SD
WASHER, .344IDX1.130DX.09T PLT
WASHER, 5/16 SPLIT LOCK PLTD
SP SCR, 5/16-18 X 1.25 HHCS SS NP
WASHER, .765IDX1.310DX.09T SS
NUT, 3/8 NPT PLASTIC
CLAMP, 3/8 HOSE (D-SLOT)
HOSEBARB, 3/8MPT X 3/8 90D
HOSE, 3/8ID WIREBOUND X 8”
CABLE TIE, .375 X 24.7
CABLE TIE, 11.38” UL/CSA
86037660 CHARIOT 05/11/07
SERIAL NO.
FROM
NOTES:
SERVICE ONLY
SERVICE ONLY
5-24
SCRUB DECK – CYLINDRICAL
34
1
2
FROM PUMP
32
3
31
4
25
30
6
8
29
15
16
27
22
25
7
21
9
17
18
19
20
13
33 12
23
24
5-25
5
14
28
26
2
86037660 CHARIOT 08/14/07
10
6
11
SCRUB DECK - CYLINDRICAL
REF
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
PART NO.
86260400
86273750
86233150
86010600
86282330
86010630
86092520
86233270
86033230
86233070
86005810
86277530
86010670
86219440
86279780
86004820
86277870
86279140
86279770
86219450
86228960
86223520
86219290
86217710
86277880
86137310
86279790
86242120
86277150
86222330
86222110
86001360
86218170
86092840
86279130
86264940
PRV NO.
880212
70011
20042
84199
39715
87013
34441
20093
54203
20003
57245
70861
87029
41487
87488
48041
70854
87085
87487
41488
09149
67598
34418
29268
70855
87098
87489
48090
70797
57504
53267
140394
35369
41535
87083
27051
QTY
2
4
2
4
1
4
1
2
1
2
2
12
12
2
2
2
4
4
4
2
4
2
2
2
8
6
6
2
2
2
2
1
12
3
DESCRIPTION
WIRE ASM, REV POLARITY JUMPER
SCR, 1/4-20 X 5/8 HHCS SS NP
CLAMP, 3/8 HOSE (D-SLOT)
VALVE, SOLENOID, 36VDC, 1/2 BARB
HOSE, 5/8 ID WIREBOUND X 16”
WASHER, 1/4 ID X 5/8 OD SS
FRAME, SCRUB DECK 24
CLAMP, 7/8” WORM GEAR SS
MANIFOLD, SOLUTION DELIVERY
CLAMP, 1/2 DIA THINWALL CONDUIT
NUT, 1/4-20 HEX NYLOCK SS
SCR, M8 X 1.25 X 20 LG BSHCS SS
WASHER, M8 FLAT DIN125A PLT
HUB, TRI-STAR BRUSH DRIVE
WASHER, M16 SMALL OD FLAT PLTD
KEY, 3/16 SQ X 7/8 CRS
SCREW, M6-1.0 X 20 LG BHSCS SS
WASHER, M6 SPLIT LOCK DIN127B
WASHER, M6 LARGE OD FLAT PLTD
HUB, TRI-STAR BRUSH IDLER
BEARING, BALL 15MM X 28MM X 7W
RING, 28MM INTERNAL SNAP
HOUSING, SCRUB PLUS DRIVE
DOOR, CYLINDRICAL BRUSH
SCREW, M8-1.25 X 35 LG SHCS SS
WASHER, M8 SPLIT LOCK
WASHER, M8 (THICK) FLAT PLTD
KNOB, 1.0 OD X 5-16-18
SCR, 5-16-18 X 2 BSHCS SS
NUT, M8 X 1.25 HEX JAM SS
MOTOR, SP BRUSH DRIVE, 36V, 3/4HP
BRUSH SET
GASKET, GEARBOX
HOPPER, CYL, DECK
WASHER, 5/16 SPLIT LOCK PLTD
CABLE TIE, 11.38” UL/CSA
86037660 CHARIOT 08/14/07
SERIAL NO.
FROM
NOTES:
SRVC ONLY
5-26
SCRUB DECK AQUA-MIZER™
16
15
1
14
2
13
17
4
5A
5B
3
6
7
8
9
3
12
11A
11B
10
18
9
5-27
86037660 CHARIOT 11/09/06
SCRUB DECK AQUA-MIZER™
REF
1
2
3
4
5A
5B
6
7
8
9
10
11A
11B
12
13
14
15
16
17
18
PART NO.
86270830
86277050
86276950
86066430
86001540
86283550
86071000
86219690
86277230
86005810
86070990
86001520
86283560
86066420
86272540
86091800
86008670
86091790
86024990
86025000
PRV NO.
57023
70782
70772
140747
140753
140939
140779
48080
70815
57245
140778
140752
140940
140746
66465
140776
80606
140774
47456
47457
QTY
4
2
9
1
1
1
1
2
2
9
1
1
1
1
2
1
2
1
-
DESCRIPTION
NUT, 5/16-18 HEX NYLOCK SS
SCR, 5/16-18 X 3/4 SHCS
SCR, 1/4-20 X 3/4 CARRIAGE SS
BAND, RIGHT AQUAMIZER
BLADE, AQUAMIZER, 12IN RGT
BLADE, AQMZR 12 RT URETHANE
BRKT, AQUAMIZER BLADE, RGT
KNOB, 1.5 OD X 5/16-18
SCR, 5/16-18 X 2.25 BSHCS SS
NUT, 1/4-20 HEX NYLOCK SS
BRKT, AQUAMIZER BLADE, LEFT
BLADE, AQUAMIZER, 12IN LEFT
BLADE, AQMZR 12 LT URETHATNE
BAND, LEFT AQUAMIZER
PIN, CLEVIS, 3/8 X 6.12, PLTD
BRKT, AQUAMIZER MTG, LEFT
COTTER, 3/8” RING
BRKT, AQUAMIZER MTG, PIVOT
AQUAMIZER RIGHT ASM. CHARIOT
AQUAMIZER LEFT ASM. CHARIOT
86037660 CHARIOT 10/20/11
SERIAL NO.
FROM
NOTES:
5-28
SIDE SQUEEGEE – CYLINDRICAL
16
17
6
15
2
10
1
14
7
8 9
13
11
10 12
17
18
4
3
5
20
19
6
9
8
14
10
15
18
11
6
10
21
14
15
13
20
7
15
10
6
10
14
4
22
3
5-29
16
86037660 CHARIOT 11/09/06
1
2
SIDE SQUEEGEE - CYLINDRICAL
REF
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
PART NO.
86066510
86276950
86283480
86277120
86071340
86228990
86271870
86226430
86271170
86010670
86242120
86086570
86079160
86259420
86271840
86272550
86008660
86277130
86091600
86226830
86091570
86071280
PRV NO.
140838
70772
140039
70792
140848
09153
57290
80636
57138
87029
48090
67600
620071
87232
57285
66485
80605
70795
140061
73268
140021
140836
QTY
2
8
2
4
1
8
8
4
4
10
2
1
4
8
8
4
4
4
1
2
1
1
DESCRIPTION
BAND, SIDE SQG, 24
SCR, 1/4-20 X 3/4 CARRIAGE SS
BLADE, SQUEEGEE, SIDE, 24
SCR, 5/16-18 X 1 PFHMS SS
BRKT, SKIRT, SQG, LH
BEARING, FLNGD, .314 ID X .502 OD
NUT, 1/4-20 HEX NYLCK THIN SS
CLEVIS, 5/16” YOKE END 5/16-18
NUT, 5/16-18 JAM
WASHER, 5/16 FLAT SS
KNOB, 1.0 OD X 5/16-18
ROD, 5/16-18 X 6.5 ADJ
PLATE, SQG LINKAGE ARM
WASHER, THRUST .51 ID X 1 OD BRO
NUT, 5/16-18 HEX NYLOCK THIN SS
PIN, CLEVIS, 5/16 X 1.00 PLTD
COTTER, 5/16” RING
SCR, 5/16-18 X 1.00 CARRIAGE SS
BRKT, SIDE SQG, WELDMENT, LH
SPRING, EXT .68 D X 3.00 L X .098 W
BRKT, SIDE SQG, WELDMENT, RH
BRKT, SKIRT, SQG, RH
86037660 CHARIOT 11/09/06
SERIAL NO.
FROM
NOTES:
5-30
SCRUB DECK - SIDE SQUEEGEE - CYLINDRICAL
2
1
4
8
3
5
6
5-31
7
86037660 CHARIOT 11/09/06
SCRUB DECK - SIDE SQUEEGEE - CYLINDRICAL
REF
1
2
3
4
5
6
7
8
PART NO.
86249050
86009200
86008670
86068570
86270830
86071350
86276070
86071440
PRV NO.
82058
81535
80606
140050
57023
140849
70593
140864
QTY
2
2
2
1
4
2
4
1
DESCRIPTION
PIN, CLEVIS 3/8 X 3.50 PLTD
KNOB, 3/8-16 4 PRONG ALUM
COTTER, 3/8” RING
BRKT, HOPPER ALIGNMENT
NUT, 5/16-18 HEX NYLOCK SS
BRKT, SIDE SQG MOUNT
5/16-18 X 3/4 CARRIAGE SS
BRKT, SIDE SQUEEGEE, LFT
86037660 CHARIOT 11/09/06
SERIAL NO.
FROM
NOTES:
5-32
SCRUB DECK SKIRTS
1
2
3
6
4
5
20
5
21
7
8
9
24
10
19
11
18
12
5
23
22
17
16
15
7
14
13
5-33
86037660 CHARIOT 11/09/06
SCRUB DECK SKIRTS
REF
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
PART NO.
86270830
86070960
86276070
86228900
86005810
86276330
86276950
86277410
86271950
86079130
86007650
86007070
86066460
86001560
86091770
86001700
86066480
86091780
86001570
86066470
86277500
86271870
86026470
86026460
PRV NO.
57023
140773
70593
09138
57245
70634
70772
70840
57300
620068
730329
70849
140769
140754
140765
140780
140781
140766
140755
140770
70853
57290
47459
47458
QTY
4
2
4
2
6
2
8
6
6
4
4
6
1
1
1
1
1
1
1
1
3
3
-
DESCRIPTION
NUT, 5/16-18 HEX NYLOCK SS
BRKT, SKIRT STOP, SCRUBDECK
SCR, 5/16-18 X 3/4 CARRIAGE SS
BEARING FLANGED, .252IDX.503OD
NUT, 1/4-20 HEX NYLOCK SS
SCR, 1/4-20 X 1.25 CARRIAGE BZ
SCR, 1/4-20 X 3/4 CARRIAGE SS
SCR, 5/16-18 X 5/8 CARRIAGE SS
NUT, 5/16-18 X 1 COUPLING SS
PLATE, SKIRT, SPACER
SPACER, .438D X .317ID X .25L
SCR, 5/16-18 X 1.00 PTMS SS
BAND, SKIRT, LEFT
BLADE, SKIRT, SCRBDCK, 24IN LFT
BRKT, SKIRT SCRUBDECK, LEFT
BLADE, SKIRT, SCRUBDECK, FRONT
BAND, SKIRT, SCRUBECK, FRONT
BRKT, SKIRT, SCRUBDECK, RIGHT
BLADE, SKIRT, SCRBDCK, 24IN RGT
BANC, SKIRT, RIGHT
SCR, 1/4-20 X 5/8 CARR SS
NUT, 1/4-20 HEX NYLOCK THIN SS
KIT, SKIRT LEFT
KIT, SKIRT RIGHT
86037660 CHARIOT 11/09/06
SERIAL NO.
FROM
NOTES:
SERVICE ONLY
SERVICE ONLY
5-34
SCRUB DECK LIFT
1
37
36
10
2
8
9
3
4
5
1
6
7
BASIC ONLY
SEE DETAIL 'A'
34
13
11
14
39
12
15
16
35
33
17
32
18
31
8
19
22
16
19
23
21
20
28
24
27
26
29
21
19
30
20
22
16
38
25
5-35
86037660 CHARIOT 02/12/07
DETAIL 'A'
SCRUB DECK LIFT
REF
PART NO.
PRV NO.
QTY
1
86276950
70772
4
*
DESCRIPTION
SERIAL NO.
FROM
NOTES:
SCR, 1/4-20 X 3/4 CARRIAGE SS
2
86223270
66482
1
PLUNGER, MICRO SWITCH
3
86276010
70580
2
SCR, 4-40 X 1.0 PPHMS
4
86072460
14387
1
BRKT, MICROSWITCH MOUNT
5
86087520
73456
2
SPACER, L2020B PLUNGER SWITCH
6
86007160
72157
1
SWITCH, 10A ROLLER MINI
7
86271280
57163
2
NUT, 4-40 W/STAR WASHER
8
86005810
57245
6
NUT, 1/4-20 HEX NYLOCK SS
9
86079150
620070
1
PLATE, MTG, DECK LIMIT
10
86277030
70780
2
SCR, 5/16-18 X 1.25 CARRIAGE SS
11
86224370
730335
2
SPACER, 1 OD X .391 ID X .500
12
86270830
57023
2
NUT, 5/16-18 HEX NYLOCK SS
13
86272460
66268
1
PIN, CLEVIS 5/16 X 3.00 PLTD
-
86008720
80637
1
14
86011950
-
15
86275510
70494
16
17
86010770
86070810
18
19
*(13)
*(26)(27)(28)
(29)(30)
WAS 80637
PIN, CLEVIS 3/8 X 2.38
*(22)
WAS 66369
1
ACTUATOR, 36VDC 3.5 STRK
*(21)
WAS 05250
2
SCR, 3/8-16 X 4.5” HHCS GR5
87143
140739
2
1
WASHER, 7/16ID X IDX.08 FLT SS
BRKT, ACTUATOR SPGS, SCRUBDECK
86255450
81376
2
SPRING COMP .96D X 4.0L X .135W
86005630
57022
4
NUT, 3/8-16 HEX NYLOCK THIN SS
20
86271530
57216
2
NUT, 3/8-24 HEX NYLOCK
21
86009050
81324
6
BEARING, 1/2 ID X 11/32L NYLON
22
86008460
80102
4
SPACER, .500OD X .391ID C .400
23
86224380
730336
2
SPACER, 1 OD X 0.391 ID X 1.063
24
86274010
70070
2
SCR, 3/8-16 X 2 HHCS
25
86001320
140353
2
BALL JOINT ASSY, 3/8-24 LH
26
86077330
31373
2
LINKAGE, .25 X 1.25 X 9.25
27
86223540
66483
2
ROD, SCRUB LIFT
28
86005800
57217
2
NUT, 3/8-24 HEX JAM
29
86276920
70755
2
SCR, 3/8-16 X 1 HHCS SS NP
30
86008810
80697
2
BALL JOINT ASY, 3/8-24 RH
31
86273850
70022
2
SCR, 1/4-20 X 2 HHCS
32
33
86010780
86079030
87162
620058
2
1
WASHER, 1/4 SPILT LOCK PLTD
PLATE, ACTUATOR SPR, SCRUBDECK
34
86091760
140741
1
BRKT, ACTUATOR MTG, SCRUBBER
35
86274110
70094
2
SCR, 1/4-20 X 1/2 SHCS
36
86007780
73576
1
SPRING, COMP .60D X 2.0L X .045W
37
86270270
27721
2
CLIP, RETAINING 7/16
38
86005830
57263
2
NUT, 3/8-24 UNF LH
39
86008660
80605
1
COTTER, 5/16” RING
*(26)(27)(28)
(29)(30)
-
86008670
80606
1
COTTER, 3/8” RING
*(22)
*(17)
WAS 80606
SEE SERIAL NUMBER PAGE
86037660 CHARIOT 04/15/08
5-36
SCRUB DECK MOUNTING- CYLINDRICAL
1
2
2
10
16
17
21
5
20
19
18
2
2
4
7
6
17
23
17
22
8
9
4
22
2
8
17
14
4
5-37
9
3
15
13
12
11
86037660 CHARIOT 04/15/08
SCRUB DECK MOUNTING - CYLINDRICAL
REF
1
2
3
4
5
6
7
8
9
10
11
12
PART NO.
86272380
86010770
86087580
86271530
86224380
86232680
86009400
86009050
86008460
86005630
86008810
86005800
PRV NO.
66217
87143
73606
57216
730336
270114
81873
81324
80102
57022
80697
57217
QTY
1
5
2
6
2
REF
1
4
4
2
2
2
DESCRIPTION
PIN, CLEVIS 3/8 X .75 PLTD
WASHER, 7/16 ID X 1D X .08 FLT SS
SPACER, 1/2 OD X .058 ID X .26 LG CRS
NUT, 3/8-24 HEX NYLOCK
SPACER, 1 OD X .391 ID X 1.063
CHAIN, #41, 1/2” PITCH X 34
CHAIN, #41, 1/2” P MASTER LINK
PIN, CLEVIS 3/8 X .75 UNPLTD
SPACER, .500 0D X .391 ID X .400
NUT, 3/8-16 HEX NYLOCK THIN SS
BALL JOINT ASY, 3/8-24 RH
NUT, 3/8-24 HEX JAM
13
86223540
66483
2
ROD, SCRUB LIFT HEX
14
15
16
17
18
19
20
21
22
23
86001320
86005830
86077330
86274660
86271840
86010670
86231090
86276690
86224370
86093180
140353
57263
31373
70255
57285
87029
80809
70715
730335
51415
2
2
2
4
2
2
2
2
4
1
BALL JOINT ASSY, 3/8-24 LH
NUT, 3/8-24 UNF LH
LINKAGE, .25 X 1.25 X 9.25
SCR, 3/8-16 X 1.5 HHCS GR5 PLTD
NUT, 5/16-18 HEX NYLOCK THIN SS
WASHER, 5/16 FLAT SS
BUMPER, RUBBER 5/16” ID X 1.50
SCR, 5/16-18 X 1.75 CARR SS
SPACER, 1 OD X .391 ID X .500 LG
LINKAGE ASM, DECK ARM
SERIAL NO.
FROM
NOTES:
WAS 67415
ROUND
*(9)
*SEE SERIAL NUMBER PAGE.
86037660 CHARIOT 11/09/06
5-38
SCRUB DECK ACTUATOR - CYLINDRICAL
1
26
25
24
4
3
7
23
27
28
14
17
20
15
7
12
21
11
10
13
8
9
14
18
15
17
16
14
29
36
31
30
40
30
32
34
1
1
41
33
37
7
2
5-39
38
39
2
22
19
36
5
86037660 CHARIOT 02/10/07
6
SCRUB DECK ACTUATOR - CYLINDRICAL
REF
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
PART NO.
86248980
86270830
86087520
86007160
86271280
86276070
86010670
86270270
86007780
86223270
86072460
86276010
86091840
86005810
86010630
86231360
86259420
86066910
86273820
86090330
86066920
86278400
86228840
86276760
86006910
86011950
86232680
86009400
86272520
86229000
86255650
86222270
86008670
86228910
OPEN
86276400
86005630
86277500
86071450
86010680
86290090
PRV NO.
81438
57023
73456
72157
57163
70593
87029
27721
73576
66482
14387
70580
140850
57245
87013
14744
87232
140851
70019
87258
140852
730351
09124
70724
70443
270114
81873
66392
09154
81627
57276
80606
09139
70642
57022
70853
140865
87030
-
QTY
3
2
2
1
2
2
4
2
1
1
1
2
1
5
4
2
4
2
1
2
1
1
2
2
2
1
1
1
1
2
2
2
4
2
1
1
2
1
4
1
DESCRIPTION
PIN, CLEVIS 3/8 X 1.75 PLTD
NUT, 5/16-18 HEX NYLOCK SS
SPACER, L2020B PLUNGER SWITCH
SWITCH, 10A ROLLER MINI
NUT, 4-40 W/STAR WASHER
SCR, 5/16-18 X 3/4 CARRIAGE SS
WASHER, 5/16 FLAT SS
CLIP, RETAINING 7/16
SPRING, COMP .60 D X 2.0 L X .045 W
PLUNGER, MICROSWITCH
BRKT, MICROSWITCH MOUNT
SCR, 4-40 X 1.0 PPHMS
BRKT, ACTUATOR SLIDER
NUT, 1/4-20 HEX NYLOCK SS
WASHER, 1/4 ID X 5/8 OD SS
BUSH, BRZ FLG .25 X .38 X .25
WASHER, THRUST .51 ID X 1 OD BRO
BAR, COMP. SPRING RETAINER, OS
SCR, 1/4-20 X 1.25 HHCS SS
WASHER, .804 ID X 1.25 OD X .179
BAR, COMP. SPRING RETAINER, IS
SPRING, COMP., 1.1 OD X 2.25 L X .148
BEARING, FLANGED .314 ID X .502 OD
SCR, 5/16-18 X 1.25 BSHCS SS
SCR, 1/4-20 X 5/8 SHCS
ACTUATOR, 36VDC, 3.5 IN STRK
CHAIN, #41, 1/2” PITCH X 34D
CHAIN, #41, 1/2” MASTER LINK
PIN, CLEVIS 3/8 X 2.75 PLTD
BEARING FLG .377 ID X .502 OD X .501
SPROCKET, #41 1/2”P 9T
NUT, PUSH FLAT RD .51 ID
COTTER, 3/8” RING
BEARING, FLANGED .377 ID X .502 OD
SCR, 3/8-16 X 3 HHCS SS
NUT, 3/8-16 HEX NYLOCK THIN SS
SCR, 1/4-20 X 5/8 CARR SS
BRKT, STRIKER
WASHER, 3/8 ID X 3/4 OD NYLON
GUARD, CHAIN
SERIAL NO.
FROM
NOTES:
*(21)
WAS 05250
*(1)
*SEE SERIAL NUMBER PAGE.
86037660 CHARIOT 09/14/07
5-40
SOLUTION - CYLINDRICAL
14
16
15
13
5
28
7
28
TO
SOLENOID
6
9
8
5
24
10
23
22
5
21
12
TO
TANK
13
11
25
33
29
30
35
19
32
46
SEE
DETAIL 'A'
31
34
13
36
37
47
18
43
5
20
45
38
1
44
17
2
3
5
39
4
42
40
41
DETAIL 'A'
5-41
86037660 CHARIOT 01/03/08
SOLUTION- CYLINDRICAL
REF
1
2
3
4
5
6
7
8
9
10
11
PART
86274070
86010650
86233390
86270860
86233150
86270990
86282320
86198050
86240390
86280910
86247760
PRV NO.
70086
87018
80887
57028
20042
57090
39710
81923
40075
39174
80960
QTY
2
2
2
2
5
4
1
1
1
1
1
12
86240600
41526
1
13
14
15
16
17
86233110
86009700
86270510
86001600
86256120
20018
82267
51457
40076
730368
2
1
1
1
1
-
86005870
59021
-
-
86136800
73839
-
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
86282370
86004310
86264920
86274410
86070690
86010650
86006100
86271820
86279130
86276780
86197940
86246090
86254320
86259450
86252730
86248010
86226950
86073960
86068780
86270830
86001530
86188210
86225680
86197420
86197540
86233410
86270830
86010670
86276070
86277460
39735
39505
27049
70195
140724
87018
65176
57270
87083
70728
40027
51461
730400
87507
70887
57312
40109
22104
140202
57023
40039
11-800354
84201
31026
40013
81270
57023
87029
70593
70847
1
1
2
4
1
4
1
1
1
1
2
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
DESCRIPTION
SCR, 10-24 X 1/2 PPHMS
WASHER, #10 X 9/16 OD
CLAMP, 7/8 DIA “P” CUSHIONED
NUT, 10-24 U-TYPE SPEED
CLAMP, 3/8 HOSE (D-SLOT)
NUT, 10-32 HEX NYLOCK SS
HOSE, 1/2ID WIRE BOUND X 49”
TEE, 3/4 FPT
HOSEBARB, 3/4 MPT X 1/2 90D
HOSE, 1/2ID WIRE BOUND X 23”
NIPPLE, 3/4 CLOSE PVCE
HOSEBARB, 3/4 MPTX1, HOSE
90DEG
CLAMP, 1.00” WORM GEAR
PLUG, 5/8” DRAIN HOSE
LANYARD, .093 X 6 NYLON
SLEEVE, .63 ID X 1.0 OD
STRAINER, 1/2 FPT 100 MESH
SERIAL
NO.
WAS 78499
SERVICE
ONLY
SERVICE
ONLY
O-RING, FILTER SEAL RON-VIK
SCREEN, 80 MESH STRAINER DEEP
HOSE, 1/2ID WIRE BOUND X 40”
HOSE, 1.0 X 18.0 DRAIN
CABLE, TIE. 7” UL/CSA
SCR, 10-32 X 1.25 PPHMS SS
BRKT, SOLUTION PUMP
WASHER, #10 X 9/16 OD
PUMP ASM, 36V
NUT, 5/16-18 CAPTIVE “J” PLTD
WASHER, 5/16 SPLIT LOCK PLTD
SCR, 5/16-18 X 3/4 HHCS SS
HOSEBARB, 3/8MPTX1/2 90D DL
LANYARD, .093 X 6”, LOOP - .26 EYE
SPACER, .17 ID X .25 OD X 3/16 LG
WASHER, 1.0 D X .1 THK, SEAL
SCR, 8-32 X 1/2 BHCS SST
NUT, 8/32 ACORN CAP, PLATED
1” HOSEBARB X 3/4” GHT NYLON
CAP, 3/4” GHT W/.17 HOLE
BRKT, STRAINER MNT
NUT, 5/16-18 HEX NYLOCK SS
HOSE BARB, 1/2 MPT X 1/2 HOSE 90
NIP, 1/2 X 3/8 HEX BR
VALVE, 3/8” FPT BALL
ELBOW, 3/8” NPT STREET
HOSEBARB, 3/8 MPT X 1/2 DL
CLAMP, 3/4 DIA CUSHION .406 DIA
NUT, 5/16-18 HEX NYLOCK SS
WASHER, 5/16 FLAT SS
SCR, 5/16-18 X 3/4 CARRIAGE SS
SCR, 5/16-18 X 5/8 BSHCS SS
NOTES:
*(11)
*(11)
*(11)
*(11)
*(11)
*(11)
*(11)
*(25)
*(25)
*(25)
*(25)
*(25)
*(25)
*(25)
*(25)
*(25)
*(25)
*(25)
*(25)
*SEE SERIAL NUMBER PAGE.
86037660 CHARIOT 01/03/08
5-42
SOLUTION - DISK
14
16
15
13
5
28
7
28
TO
SOLENOID
6
9
8
5
24
10
23
12
22
5
TO
TANK
13
21
11
25
33
29
30
35
19
32
31
SEE
DETAIL 'A'
34
13
26
5
27
20
40
1
18
39
2
5
38
3
37
4
36
20
DETAIL 'A'
5-43
86037660 CHARIOT 01/03/08
17
SOLUTION - DISK
REF
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
PART NO.
86274070
86010650
86233390
86270860
86233150
86270990
86281940
86198050
86240390
86282190
86247760
86240600
86233110
86009700
86270510
86001600
86007940
86005870
86136800
86281950
86004310
86264920
86274410
86070690
86010650
86006100
86271820
86279130
86276780
86197940
86246090
86254320
86259450
86252730
86248010
86226950
86073960
86235450
86001590
86197420
86225680
86197540
PRV NO.
70086
87018
80887
57028
20042
57090
39540
81923
40075
39616
80960
41526
20018
82267
51457
40076
73836
59021
73839
39541
39505
27049
70195
140724
87018
65176
57270
87083
70728
40027
51461
730400
87507
70887
57312
40109
22104
31068
40049
31026
84201
40013
QTY
2
2
2
2
5
4
1
1
1
1
1
1
2
1
1
1
1
1
1
3
4
1
4
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
DESCRIPTION
SCR, 10-24 X 1/2 PPHMS
WASHER, #10 X 9/16 OD
CLAMP, 7/8 DIA “P” CUSHIONED
NUT, 10-24 U-TYPE SPEED
CLAMP, 3/8 HOSE (D-SLOT)
NUT, 10-32 HEX NYLOCK SS
HOSE, 1/2ID WIRE BOUND X 40”
TEE, 3/4 FPT
HOSEBARB, 3/4 MPT X 1/2 90D
HOSE, 1/2ID WIRE BOUND X 13”
NIPPLE, 3/4 CLOSE PVCE
HOSEBARB, 3/4 MPTX1, HOSE 90DEG
CLAMP, 1.00” WORM GEAR
PLUG, 5/8” DRAIN HOSE
LANYARD, .093 X 6 NYLON
SLEEVE, .63 ID X 1.0 OD
STRAINER, DEEP, 100 MESH
O-RING, FILTER SEAL RON-VIK
SCREEN, 100 MESH STRAINER DEEP
HOSE, 1/2ID WIRE BOUND X 32”
HOSE, 1.0 X 18.0 DRAIN
CABLE, TIE. 7” UL/CSA
SCR, 10-32 X 1.25 PPHMS SS
BRKT, SOLUTION PUMP
WASHER, #10 X 9/16 OD
PUMP ASM, 36V
NUT, 5/16-18 CAPTIVE “J” PLTD
WASHER, 5/16 SPLIT LOCK PLTD
SCR, 5/16-18 X 3/4 HHCS SS
HOSEBARB, 3/8MPTX1/2 90D DL
LANYARD, .093 X 6”, LOOP - .26 EYE
SPACER, .17 ID X .25 OD X 3/16 LG
WASHER, 1.0 D X .1 THK, SEAL
SCR, 8-32 X 1/2 BHCS SST
NUT, 8/32 ACORN CAP, PLATED
1” HOSE BARB X 3/4” GHT NYLON
CAP, 3/4” GHT W/.17 HOLE
ELBOW, 3/8 FPT PVC SCH 80
HOSEBARB, 3/8 MPT X 1/2 NYLON
ELBOW, 3/8 NPT STREET
VALVE, 3/8” FPT BALL
HOSEBARB, 3/8 MPT X 1/2 DL
SERIAL NO.
FROM
NOTES:
WAS 78499
SERVICE ONLY
SERVICE ONLY
*(11)
*(11)
*(11)
*(11)
*(11)
*(11)
*(11)
*(25)
*(25)
*(25)
*(25)
*(25)
*SEE SERIAL NUMBER PAGE.
86037660 CHARIOT 10/13/08
5-44
SQUEEGEE - DISK
1
39
2
38
37
3
9
4
36
40
5
8
35
5
6
7
6
34
8
5
33
9
11
7
10
11
15
12
13
14
15
16
17
18
19A
19B
20
32
30
21
29
22
25
23
24
26
31
27A
27B
28
5-45
86037660 CHARIOT 11/09/06
SQUEEGEE - DISK
REF
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19A
19B
20
21
22
23
24
25
26
27A
27B
28
29
30
31
32
33
34
35
36
37
38
39
40
PART NO.
86004890
86070920
86006270
86007780
86005630
86270830
86010670
86001350
86011020
86005650
86276950
86083290
86276710
86083250
86271870
86007040
86271820
86087830
86001630
86283540
86083270
86083260
86277000
86276990
86277450
86008390
86083280
86001580
86283510
86066440
86006400
86009170
86009180
86066450
86009910
86274130
86071070
86071060
86009200
86277440
86008660
86277460
PRV NO.
48095
140759
66276
73576
57022
57023
87029
140390
89202
57031
70772
66463
70717
66459
57290
70680
57270
140760
140764
140938
66461
66460
70777
70776
70846
78493
66462
140763
140935
140761
67380
81488
81489
140762
82576
70098
140795
140794
81535
70845
80605
70847
QTY
2
2
2
2
2
3
4
2
4
2
4
2
2
1
4
5
5
1
1
1
1
1
4
2
2
1
1
1
1
1
4
1
1
1
1
2
1
1
1
1
2
1
DESCRIPTION
KNOB, ALUM 3/8-16 NYLOCK NUT SS
BRKT, SQG WHEEL
PIN, CLEVIS 5/16 X 1.63 PLTD
SPRING, COMP .60D X 2.0L X .045 W
NUT, 3/8-16 HEX NYLOCK THIN SS
NUT, 5/16-18 HEX NYLOCK SS
WASHER, 5/16 FLAT SS
BUSHING, SPANNER .435 X 1.10
WHEEL, 3” DIA CUSHION RUBBER
NUT, 5/16-18 HEX
SCR, 1/4-20 X 3/4 CARRIAGE SS
PLATE, SQG WHEEL NMT BUMPER
SCR, 5/16-18 X 2.0 CARRIAGE SS
PLATE, SQG TOP 33”
NUT, 1/4-20 HEX NYLOCK THIN SS
SCR, 5/16-18 X 1 THUMB SS TYPE P
NUT, 5/16-18 CAPTIVE “J” PLTD
STRAP, SQUEEGEE
BLADE, SQU, FRONT 36.7
BLADE, SQU, FRONT 36.7 URETHANE
PLATE, SQG VERICAL FILLER (F)
PLATE, SQG BOTTOM 33”
SCR, 1/4-20 X 1.5 CARRIAGE SS
SCR, 3/8-16 X 3.5 CARRIAGE SS
SCR, 3/8-16 X 2 LG CARRIAGE SS
TUBE ASM, SQUEEGEE VAC
PLATE, SQG VERTICAL FILLER
BLADE, SQU, REAR 40.6 LINATEX
BLADE, SQU, REAR 40.6 URETHANE
BAND, REAR SQUEEGEE
RIVET, 5/32 OF X 1/8 GRIP
LATCH, SQUEEGEE STRAP
STRIKER, SQUEEGEE STRAP REAR
BAND, SQG REAR RH
VIAL, LEVEL
SCR, 8-32 X 3/8 PHTC ‘F’ PLATD
BRKT, SQG QUICK CONNECT LOCK
BRKT, SQG QUICK CONNECT MTG
KNOB, 3/8-16 4 PRONG ALUM
SCR, 3/8-15 X 2.5 LG BSHCS SS
COTTER, 5/16 RING
SCR, 5/16-18 X 5/8 BSHCS SS
SERIAL NO.
FROM
NOTES:
NOTE: Complete Squeegee Assembly available, Part No. 47455
86037660 CHARIOT 02/20/07
5-46
SQUEEGEE - CYLINDRICAL
1
2
39
3
6
5
4
7
37
6
38
7
36
8
35
9
34
12
10
4
11
33
4
32
13
31
42
30
17
16
28
18
26
19
27
29
20
27
25
21
24
23
5-47
86037660 CHARIOT 02/20/07
22A
22B
15
14A
14B
SQUEEGEE - CYLINDRICAL
REF
1
2
3
4
5
6
7
8
9
10
11
12
13
14A
14B
15
16
17
18
19
20
21
22A
22B
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
PART NO.
86004890
86069870
86007780
86005630
86271840
86001350
86011020
86010670
86005650
86083420
86276710
86276950
86087850
86283490
86283530
86083470
86005810
86071260
86083460
86083430
86277000
86276990
86283500
86283520
86066490
86009180
86009170
86066500
86006400
86277450
86008390
86271820
86007040
86009910
86274130
86071070
86071190
86009200
86277440
86008660
86006270
86277460
86270830
86271870
PRV NO.
48095
140531
73576
57022
57285
140390
89202
87029
57031
66822
70717
70772
140833
140841
140937
66828
57245
140830
66827
66823
70777
70776
140842
140936
140834
81489
81488
140835
67380
70846
78493
57270
70680
82576
70098
140795
140823
81535
70845
80605
66276
70847
57023
57290
QTY
2
2
2
6
2
2
4
2
2
2
2
4
1
1
1
1
4
1
1
1
2
2
1
1
1
1
1
1
4
2
1
4
4
1
2
1
1
1
1
2
2
1
1
2
DESCRIPTION
KNOB, ALUM 3/8-16 NYLOCK NUT SS
BRKT, SQG WHEEL
SPRING, COMP .60 D X 2.0 L X .045 W
NUT, 3/8-16 HEX NYLOCK THIN SS
NUT, 5/16-18 HEX NYLOCK THIN SS
BUSHING, SPANNER .435 X 1.10
WHEEL, 3” DIA CUSHION RUBBER
WASHER, 5/16 FLAT SS
NUT, 5/16-18 HEX
PLATE, BUMPER WHEEL MOUNT
SCR, 5/16-18 X 2.0 CARRIAGE SS
SCR, 1/4-20 x 3/4 CARRIAGE SS
STRAP, SQUEEGEE
BLADE, SQU FRONT 29.4
BLADE, SQU FRONT 29.4 URETHANE
PLATE, SQG VERTICAL FILLER (F)
NUT, 1/4-20 HEX NYLOCK SS
BRKT, SQUEEGEE TOP PLATE
PLATE, SQG VERTICAL FILLER (R)
PLATE, SQUEEGEE BOTTOM 33 IN
SCR, 1/4-20 X 1.5 CARRIAGE SS
SCR, 3/8-16 X 3.5 CARRIAGE SS
BLADE, SQU REAR 31.3 LINATEX
BLADE, SQU REAR 31.3 URETHANE
BAND, REAR SQUEEGEE
STRIKER, SQUEEGEE STRAP REAR
LATCH, SQUEEGEE STRAP
BAND, REAR SQUEEGEE
RIVET, 5/32 OF X 1/8 GRIP
SCR, 3/8-16 X 3 LG CARRIAGE SS
TUBE ASM, SQUEEGEE VAC
NUT, 5/16-18 CAPTIVE “J” PLTD
SCR, 5/16-1/ X 1 THUMB SS TYPE P
VIAL, LEVEL
SCR, 8-320X 3/8 PHTC “F” PLTD
BRKT, SQG QUICK CONNECT LOCK
BRKT, SQG QUICK CONNECT MTG
KNOB, 3/8-16 4 PRONG ALUM
SCR, 3/8-16 X 2.50 LG BSHCS SS
COTTER, 5/16” RING
PIN, CLEVIS 5/16 X 1.63 PLTD
SCR, 5/1/6-18 x 5/8 BSHCS SS
NUT, 5/16-18 HEX NYLOCK SS
NUT,1/4-20 HEX NYLOCK THIN SS
SERIAL NO.
FROM
NOTES:
*(5)
*(5)
*SEE SERIAL NUMBER PAGE.
86037660 CHARIOT 02/20/07
5-48
SQUEEGEE LIFT-BASIC
29
30
27
3
9
3
5
4
26
4
3
31
4
32
4
28
24
3
23
3
4
14
3
17
18
19
20
21
4
22
4
10
9
4
16
4
2
15
9
3
25
35
4
1
14
13
37
12
36 4
34
4
6
10
38
11
3
33
8
9
5
3
7
5-49
3
5
86037660 CHARIOT 08/14/07
SQUEEGEE LIFT-BASIC
REF
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
PART NO.
86277490
86259420
86010670
86270830
86276760
86277460
86274720
86083490
86231150
86223370
86083500
86270920
86257120
86226630
86076610
86238360
86083360
86232670
86073890
86231560
86279350
86091820
86276070
86066130
86295860
86254280
86083350
86270870
86254580
86277410
86277400
86083340
86083440
86276070
86007020
86278980
86279450
86073600
PRV NO.
70851
87232
87029
57023
70724
70847
70264
66831
09151
66464
66832
57049
72192
51010
38319
36215
66474
270099
270096
270097
87140
140807
70593
89501
730331
66473
57029
80835
70840
70839
66471
66824
70593
70673
87014
87161
66833
QTY
2
2
19
21
9
1
1
1
7
4
1
2
1
2
1
1
2
1
1
1
1
1
1
1
1
1
2
2
1
4
1
1
1
1
1
2
4
1
DESCRIPTION
SCR, 6-32 X 1.5 PPHMS SS
WASHER, THRUST .51ID X 1 OD
WASHER, 5/16 FLAT SS
NUT, 5/16-18 HEX NYLOCK SS
SCR, 5/16-18 X 1.25 BSHCS SS
SCR, 5/16-18 X 5/8 BSHCS SS
SCR, 5/16-18 X 1.5 HHCS SS
PLATE, PULLEY MOUNT, CORNER
BUSHING FLANGED, .314ID X .502OD
PULLEY, PLASTIC 3.0 DIA.
PLATE, PULLEY RETAINER, CORNER
NUT, 6-32 HEX NYLOCK SS
SWITCH, DPST SNAP ACTION
LINK, #35 MASTER
HANDLE, SQUEEGEE LIFT
GRIP, 3/16 X 1.0 ORANGE
PLATE, KEEPER BOTTOM
CHAIN, #35, 3/8 PITCH X 29
CAM, SQUEEGEE LIFT
CABLE, SQUEEGEE LIFT BASIC
WASHER, WAVE 1/2ID X 3/4D X .125
BRKT, SIDE CHANNEL R
SCR, 5/16-18 X 3/4 CARRIAGE SS
ASM, HANDLE RETAINER
INSULATOR, SWITCH
SPACER, 1.00 OD X .32 ID X .375
PLATE, KEEPER TOP
NUT, 1/4-20 HEX SS
SPACER, .32ID X .71OD X .76L NYL
SCR, 5/16-18 X 5/8 CARRIAGE SS
SCR, 5/16-18 X 1.75 BSHCS SS
PLATE, CAM MOUNT
PLATE, PULLEY MOUNTING, CENTER
SCR, 5/16-18 X 3/4 CARRIAGE SS
SCR, 5/16-18 X 1.25 HHCS SS NP
WASHER, #8 INT.STAR
WASHER, #6 FLAT SAE PLTD
BRKT, PULLEY RETAINER, SINGLE
SERIAL NO.
FROM
NOTES:
*(4)
*(4)
*(15)
*(4)
*SEE SERIAL NUMBER PAGE.
86037660 CHARIOT 08/14/07
5-50
SQUEEGEE LIFT-DELUXE
1
28
2
3
30
5
1
2
28
2
28
25
5
13
3
10
20
13
13
2
10
10
6
11 12
8
28
9
7
29
16
14
27
22
13
10
17
17
18 13 19
21
11
16
10
23
13
26
10
24
16
4
17 13 20
10
5-51
16
86037660 CHARIOT 05/26/09
SQUEEGEE LIFT-DELUXE
REF
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
PART NO.
86068190
86273820
86316550
86083490
86068230
86270870
86002780
86277410
86075430
86270830
86276070
86277400
86010670
86277460
86259420
86223370
86231150
86083440
86276760
86274720
86071300
86224290
86071310
86083500
86271840
86074160
86277480
86271870
86228880
86326650
PRV NO.
140793
70019
66831
140840
57029
270098
70840
270700
57023
70593
70839
87029
70847
87232
66464
09151
66824
70724
70264
140843
730008
140844
66832
57285
270101
70850
57290
09132
-
QTY
1
1
1
1
1
3
1
4
1
15
3
2
10
1
1
6
5
1
2
2
1
2
1
1
1
1
2
2
1
-
DESCRIPTION
BRACKET, ACTUATOR MOUNT
SCR, 1/4-20 X 1.25 HHCS
ACTUATOR, 36VDC, 4.5” STROKE
PLATE, PULLEY MOUNT, CORNER
BRACKET, SQG LIFT PULLEY MOUNT
NUT, 1/4-28 HEX SS
CABLE, SQUEEGEE LIFT DELUXE
SCR, 5/16-18 X 5/8 CARRIAGE SS
COVER, SQUEEGEE LIFT
NUT, 5/16-18 HEX NYLOCK SS
SCR, 5/16-18 X 3/4 CARRIAGE SS
SCR, 5/16-8 X 1.75 BSHCS SS
WASHER, 5/16 FLAT SS
SCR, 5/16-18 X 5/8 BSHCS SS
WASHER, THRUST .51ID X 1 OD BRO
PULLEY, PLASTIC 3.0 DIA
BUSHING, FLANGE, .314ID X .502OD
PLATE, PULLEY MOUNTING, CENTER
SCR, 5/16-18 X 1.25 BSHCS SS
SCR, 5/16-18 X 1.50 HHCS SS
BRACKET, PULLEY RETAINER, DOUBLE
SPACER, .317ID X .5OD X .44 LG
BRKT, PULLEY RETAINER, DOUBLE
PLATE, PULLEY RETAINER, CORNER
NUT, 5/16-18 HEX NYLOCK THIN SS
CHANNEL, RIGHT DELUXE
SCR, 5/16-18 X 1/2 PTHMS SS
NUT, 1/4-20 HEX NYLOCK THIN SS
BEARING, .314 ID X .503 OD X 1
ASM, ACTUATOR AND BRACKETS
SERIAL NO.
FROM
*(32)
*(4)
*(4)
NOTES:
WAS 05254***
*(4)
*(4)
*(4)
***
*SEE SERIAL NUMBER PAGE.
**CALL MANUFACTURER FOR SERIAL NUMBER
*** FOR REPLACEMENT OF 05254
86037660 CHARIOT 05/26/09
5-52
SQUEEGEE SWING
1
1
24
23
27
22
6
21
2
20
7
26
3
4
6
19
18
25
5
16
6
15
17
14
7
13
6
12
11
10
6
5-53
9
8
86037660 CHARIOT 05/08/09
SQUEEGEE SWING
REF
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
PART NO.
86276690
86091530
86090300
86083370
86091540
86270830
86271530
86008810
86271980
86223590
86001320
86091810
86224290
86083400
86276760
86272630
86008650
86228840
86277030
86224380
86083150
86083310
86226030
86222580
86070820
86278910
86326670
PRV NO.
70715
140787
87247
66475
140800
57023
57216
80697
57303
67510
140353
140798
730008
66479
70724
80771
80604
09124
70780
730336
66446
66468
89268
66466
140740
-
QTY
7
1
2
2
1
9
2
1
1
1
1
1
2
1
2
1
1
4
4
4
2
1
2
2
2
1
1
DESCRIPTION
SCR, 5/16-18 X 1.75 CARR SS
BRACKET, SQUEEGEE SIDE PIVOT
WASHER, 1.25 ID X .075 OCTAGON
PLATE, SQG SWING SPACER
BRACKET, H PIVOT MOUNT
NUT, 5/16-18 HEX NYLOCK SS
NUT, 3/8-24 HEX NYLOCK
BALL JOINT ASY, 3/8-24 RH
NUT, 3/8-24 WING SS
ROD, CAMBER ADJUST
BALL JOINT ASSY, 3/8-24 LH
BRKT, SQG QUICK CONNECT
SPACER, .317ID X .500 X .44LG
PLATE, CABLE RETAINING
SCR, 5/16-18 X 1.25 BSHCS SS
PIN, CLEVIS 1/4 X .88 PLTD
COTTER, 1/4 RING
BEARING, FLANGED .314 ID X .502 0D
SCR, 5/16-18 X 1.25 CARRIAGE SS
SPACER, 1 OD X .343 ID X 1.063
PLATE, SQUEEGEE SWING
PLATE, WHEEL RETAINER
WHEEL, 1.000 OD X .323 ID X .750 SS
PIN, .312 DIA X 1.250 LG SS
BRKT, SQUEEGEE SWING HORIZ
WASHER, 3/8 ID X 7/8 OD SS
PLATE, CABLE GUARD
SERIAL NO.
FROM
NOTES:
*(33)
*(33)
*SEE SEERIAL NUMBER PAGE
86037660 CHARIOT 05/08/09
5-54
SQUEEGEE LIFT - CYLINDRICAL
1
16
17
8
2
15
4
7
18
10
11
3
4
5
6
7
5
12
9
7
8
13
14
8
5-55
86037660 CHARIOT 11/09/06
SQUEEGEE LIFT - CYLINDRICAL
REF
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
PART NO.
86276690
86276990
86224370
86228840
86259420
86071160
86010670
86270830
86007020
86007270
86278910
86094270
86004890
86224290
86277030
86009560
86010630
86008650
PRV NO.
70715
70776
730335
09124
87232
140819
87029
57023
70673
730006
87003
730344
48095
730008
70780
82053
87013
80604
QTY
4
1
4
6
8
1
7
7
1
1
1
1
1
1
2
1
1
1
DESCRIPTION
SCR, 5/16-18 X 1.75 CARR SS
SCR, 3/8-16 X 3.5 CARRIAGE SS
SPACER, 1 OD X .391 ID X .500
BEARING, FLANGED .314 ID X .502 OD
WASHER, THRUST .51 ID X 1 OD BRO
BRKT, SQG MOUNT VERTICAL
WASHER, 5/16 FLAT SS
NUT, 5/16-18 HEX NYLOCK SS
SCR, 5/16-18 X 1.25 HHCS SS NP
SPRING, COMP 1.10 OD X 2.0 L X .148 W
WASHER, 3/8 ID X 7/8 OD SS
SQG TRACK WHEEL
KNOB, ALUM 3/8-16 NYLOCK NUT SS
SPACER, .317 ID X .50 D X .44 LG
SCR, 5/16-18 X 1.25 CARRIAGE SS
PIN, CLEVIS 1/4 X .63 PLTD
WASHER, 1/4 ID X 5/8 OD SS
COTTER, 1/4” RING
86037660 CHARIOT 11/09/06
SERIAL NO.
FROM
NOTES:
5-56
SQUEEGEE LIFT - CYLINDRICAL
1
6
2
3
33
7
4
8
9
5
10
11
12
13
15
14
16
15
17
18
12
19
11
15
17
17
32
11
12
11
13
15
21
22
12
34
20
27
24
28
23
30
16
25
11
29
11
15
26
5-57
15
86037660 CHARIOT 08/14/07
15
31
SQUEEGEE LIFT - CYLINDRICAL
REF
PART NO.
PRV NO.
QTY
DESCRIPTION
1
86238360
36215
1
GRIP, 3/16 X 1.0 ORANGE
2
86076610
38319
1
HANDLE, SQUEEGEE LIFT
3
86257120
72192
1
SWITCH, DPST SNAP ACTION
4
86008650
80604
1
COTTER, 1/4” RING
5
86279450
87161
2
WASHER, #6 FLAT SAE PLTD
6
86275550
70500
2
SCR, #6-32 X 1.25 PPHMS
7
86259420
87232
2
WASHER, THRUST .51 ID X 1 OD BRO
8
86009560
82053
1
PIN, CLEVIS 1/4 X .63 PLTD
9
86270920
57049
2
NUT, 6-32 HEX NYLOCK SS
10
86007020
70673
1
SCR, 5/16-18 X 1.25 HHCS SS NP
11
86010670
87029
8
WASHER, 5/16 FLAT SS
12
86231150
09151
5
BUSHING, FLANGE, .314 ID X .502 OD
13
86276760
70724
3
SCR, 5/16-18 X 1.25 BSHCS SS
14
86277460
70847
1
SCR, 5/16-18 X 5/8 BSHCS SS
15
86270830
57023
12
NUT, 5/16-18 HEX NYLOCK SS
16
86276070
70593
2
SCR, 5/16-18 X 3/4 CARRIAGE SS
17
86223370
66464
4
PULLEY, PLASTIC 3.0 DIA
18
86073600
66833
1
BRKT, PULLEY RETAINER, SINGLE
19
86083440
66824
1
PLATE, PULLEY MOUNTING, CENTER
20
86276910
70754
2
SCR, 5/16-18 X 3 HHCS SS NP
21
86083500
66832
1
PLATE, PULLEY RETAINER, CORNER
22
86083490
66831
1
PLATE, PULLEY MOUNT, CORNER
23
86279630
87212
1
WASHER, .344 ID X .13 OD X .09 T PLTD
24
86254280
730331
1
SCR, 8-32 X 1/4 SPHMS BLK NYL
25
86006930
70514
1
SCR, 5/16-18 X 1.00 BSHCS SS
26
86091820
140807
1
BRKT, SIDE CHANNEL R
27
86001350
140390
4
BUSHING, SPANNER .435 X 1.10
28
86011020
89202
4
WHEEL, 3” DIA CUSHION RUBBER
29
86277130
70795
4
SCR, 5/16-18 X 1.00 CARRIAGE SS
30
86071290
140837
2
BRKT, SIDE WHEEL MOUNT
31
86239720
41520
1
HORN, 108 DB MINIATURE PIEZO
32
86231570
270105
1
CABLE, SQG LIFT, SCRUBPLUS
33
86295860
-
1
INSULATOR, SWITCH
34
86274720
70264
1
SCR, 5/16-18 X 1.50 HHCS SS
SERIAL NO.
FROM
NOTES:
*(23)
*SEE SERIAL NUMBER PAGE.
86037660 CHARIOT 08/14/07
5-58
STEERING
1
2
3
4
5
6
8
7
28
9
10
11
12
13
27
26
25
14
15
24
14
19
29
23
22
21
20
19
18
16
17
7
5-59
86037660 CHARIOT 11/09/06
STEERING
REF
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
-
PART NO.
86271610
86234810
86259610
86224050
86228790
86091740
86270830
86005610
86219600
86272900
86224060
86219650
86228670
86276070
86224800
86010670
86135970
86275190
86008610
86001030
86224320
86224810
86005630
86002750
86278940
86010780
86274330
86279130
86253200
86232780
PRV NO.
57228
27945
730117
730318
09111
140720
57023
57016
45012
67416
730319
48110
09072
70593
730315
87029
48045
70377
80595
09148
730221
730316
57022
270088
87008
87162
70175
87083
70806
279001
QTY
1
1
1
1
1
1
4
1
1
1
1
1
1
4
1
2
1
1
2
1
1
1
1
1
2
1
1
2
1
-
DESCRIPTION
NUT, 5/8-16 HEX NYLOCK THN
COVER, STEERING WHEEL
WHEEL, STEERING 40 SPLINE HUB
SHAFT, UPPER STEERING
BEARING, FLANGE .88ODX.75IDX.75
BRKT, UPPER STEERING
NUT, 5/16-18 HEX NYLOCK SS
NUT, 7/8 DIA PUSHLOCK
JOINT, UNIVERSAL FEMALE
RING, 3/4” KLIP
SHAFT, LOWER STEERING
KEY, 5MM SQ X 39MM L
BEARING, 3/4” BORE FLANGED
SCR, 5/16-18 X 3/4 CARRIAGE SS
SPROCKET, STEERING SHAFT
WASHER, 5/16 FLAT SS
KEY, 3/16 SQ X 5/8 LONG
SCR, 3/8-16 X 1.25 HHCS SS
FLANGE, BEARING PRESS STEEL
BEARING, BALL 3/4 BORE SPHERED
SPACER, .63 OD X .385ID X .64L
SPROCKET, DRIVE WHEEL STEERING
NUT, 3/8-16 HEX NYLOCK THIN SS
CHAIN, ISO 08B, 12.7MM PITCH
WASHER, 1/4 ID X 1-1/4OD
WASHER, 1/4 SPLIT LOCK PLTD
SCR, M6 X 20HHMS PLTD
WASHER, 5/16 SPLIT LOCK
SET SCR, M6 X 25 NP
CHAIN, MASTERLINK 12.7MM
86037660 CHARIOT 11/09/06
SERIAL NO.
FROM
NOTES:
SERVICE ONLY
SERVICE ONLY
5-60
TANK
5
3
4
32
2
1
6
7
37
11
22
19
8
9
23
20
31
21A
21B
17
11
35
11
12
10
36
27
14
29
13
15
16
34
33
18
26
24
25
29
30
27
5-61
86037660 CHARIOT 12/12/08
28
TANK
REF
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21A
21B
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
PART NO.
86001510
86006470
86221900
86271940
86010630
86006480
86246080
86004010
86003350
86310190
86006860
86276840
86256100
86275800
86002620
86004000
86033570
86002390
86003010
86264950
86305960
86004380
86197870
86003680
86311740
86004430
86002380
86032870
86006760
86177050
86279630
86257570
86310180
86003710
86004440
86277560
86025200
86199840
98406760
PRV NO.
140712
67513
54198
57299
87013
67514
51368
35274
28063
70403
70744
730333
70546
260-64A
35255
78934
20063
27759
27746
39550
31101
34380
39707
20046
75455
70305
03-000176
87212
51407
34447
39717
70866
31377
090-12A
-
QTY
1
1
1
8
8
1
1
1
1
1
5
8
1
6
1
1
1
1
1
3
1
1
1
1
1
1
1
1
6
1
6
1
1
1
1
1
1
1
1
DESCRIPTION
BAG, INNER TANK
RETAINER, BACK BAG
MANDREL, BAG
NUT, 1/4-20 ACORN SS
WASHER, 1/4-20 X 5/8 OD SS
RETAINER, MAIN BAG
LANYARD, 18.0 W/LOOP & EYE
GASKET, DOME EDGE
DOME, COVER, 10X13
BASKET, STRAINER, DOME
SCR, #10X1/2 PPHST TYPE B
SCR, 1/4-20X1 PFH BLK SS
STRAINER, 3/4-MNPT, 12 MESH
SCR, 8 X 3/4 PFHT/S BLK ZINC
ACCESS COVER CLEAR 6” W/RIM
GASKET, TANK LID
TUBE ASM
CLAMP, 1.75” WORM GEAR X .312
CUFF, HOSE 1.5” BLK A 2161
CABLE TIE, .19W X 11.5L BLK
HOSE ASM, 1.5 BLK PVC VAC X 67
HOSE ASM, 1.5 BLK VAC X 50
ELBOW, 1.5 FS X FS 90 DEG
FLOAT, SHUT-OFF
HOSE, 2.0 X 37.0, DRAIN
HOSE ASM, 2 X 37.0 DRAIN, ASM
CLAMP, 2.25” WORM GEAR
TANK
SCR, 5/16-18 x 3/4 HHCS GR5 PLTD
CLAMP, HOSE #20
WASHER, .344 ID X 1.13 OD X .09T PLT
TETHER, DRAIN HOSE, 1.5
PLATE, STRAINER BASKET
FLAP, TANK DEBRIS
CAP, DRAIN HOSE
SCR, #6 X 1/2 SHT MTL SS
ELBOW ASM, FLOAT
FLOAT SCREEN CAGE ASSY
KIT, DOME BASKET
SERIAL NO.
FROM
NOTES:
**
**
*(31)
DISK
SCRUB PLUS
**
HOSE & CAP
*(14)
*(31)
*(7)
*(19)
*(19)
* SEE SERIAL NUMBER PAGE.
** CALL MANUFACTURER FOR SERIAL NUMBER
86037660 CHARIOT 07/05/11
5-62
VACUUM
15
14
10
9
11
8
7
6
12
4 5
12
5-63
3
86037660 CHARIOT 11/09/06
13
VACUUM
REF
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
PART NO.
86270990
86083030
86083010
86270830
86083020
86005500
86135310
86237880
86237890
86078650
86238040
86064740
86274070
86270860
86236530
86236540
PRV NO.
57090
66430
66428
57023
66429
53809
140686
35276
35277
36241
36243
270100
70086
57028
34436
34437
QTY
4
1
1
3
1
1
1
1
1
2
1
2
2
1
2
DESCRIPTION
NUT, 10-32 HEX NYLOCK SS
PLATE, VAC MOTOR ADAPT
PLATE, VAC SPACER
NUT, 5/16-18 HEX NYLOCK SS
PLATE, VAC MOUNTING
VAC MOTOR 36VDC 3 STG
BRUSH SET, 24/36V VAC WINDSOR
GASKET, 5.7 VAC MOTOR
GASKET, VAC MOUNT
GUARD, CHAIN RT
GASKET, 1/4 T X 3/4 W X 24 L
VAC CHANNEL COVER
SCR, 10-24 X 1/2 PPHMS
NUT, 10-24 U-TYPE SPEED
FOAM, POLYESTER, 1X3X18
FOAM, POLY, 1X2 CURVED W/ADH
SERIAL NO.
FROM
NOTES:
SERVICE ONLY
*(3)
*(3)
*SEE SERIAL NUMBER PAGE.
86037660 CHARIOT 11/09/06
5-64
WHEEL-FRONT DRIVE, CHAIN
1
2
3
4
9
9
5
20
18
17
33
8
32
9
10
11
12
6
7
31
13
14
30A
30B
29
28
15
27
17
26
18
17
25
22
1
35
23
24
18
21
14
5-65
16
86037660 CHARIOT 08/19/09
15
19
WHEEL-FRONT DRIVE, CHAIN
REF
PART NO.
PRV NO.
QTY
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30A
30B
31
32
33
34
35
86223980
86223480
86219420
86224040
86005510
86216210
86227440
86136360
86010720
86222730
86318830
86275640
86279700
86219620
86007620
86279710
86136640
86222710
86279690
86277340
86002730
86232770
86232780
86222760
86007630
86002710
86224270
86277330
86222720
86224330
86219630
86000850
86219640
86011120
86259920
86222750
86224340
86222770
86217720
86277320
09134
67450
41510
730306
53810
53820
05261
57275
87086
620038
70515
87244
48106
730310
87245
70262
620036
87243
70830
270085
279000
279001
620041
730311
270076
730293
70829
620037
730294
48107
05231
48108
89262
89273
620040
730295
620042
29269
70828
4
2
1
1
1
1
1
1
11
4
5
1
1
3
2
1
12
12
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
SEALED BALL BRNG, 25MM X 52MM
RING, 52MM INTERNAL SNAP
STEERING, HUB
SHAFT, ASM, DRIVE PIVOT
MOTOR, 36V 180RPM GEAR
BRUSH SET MOTOR 53810
ARMATURE 53810 MOTOR
NUT, M10X1.5 HEX NYLOCK PLTD
WASHER, M10 X 30 PLTD
PLATE, DRIVE WHEEL YOKE
SCR, M10 X 30 SHCS
SCR, 3/8-24 X 3/4 HHCS GR5 PLTD
WASHER, M10 X 18 FLAT
KEY, 1/4 SQ. X .63
SPROCKET, MOTOR SHAFT
WASHER, M8 (2 THK X 26 OD)
SCR, M8-1.25 X 20HHMS PLTD
PLATE, CHAIN COVER
WASHER, M6 SPLIT LOCK BLK
SCR, M6 X 15 HHCS BLK
CHAIN, ISO 08B 12.7MM PITCH/LINK
CHAIN, OFF-SET LINK 12.7MM
CHAIN, MASTERLINK 12.7MM
PLATE, DRIVE YOKE RH
SPROCKET, DRIVE WHEEL
CHAIN TENSIONER
SLEEVE, CHAIN TENSIONER
SCR, M10 X 45 HHCS
PLATE, BEARING RETAINER
SPACER, 25.5ID X 45OD X 65L
KEY, 3/16 SQ X .67
AXLE, DRIVE
KEY, 1/4 SQ X 1.5
WHEEL, 10X2.5X1.06 W/KEYWY
WHEEL, 10X2.5 W/KEYWY GRY
PLATE, DRIVE YOKE FRONT
SPACER, 25.5ID X 45OD X 43L
PLATE, BEARING COVER
DRIVE ASM, MOTOR
SCR, M10 X 30 HHCS
86037660 CHARIOT 08/19/09
SERIAL NO.
FROM
NOTES:
SERVICE ONLY
SERVICE ONLY
OPTIONAL
COMPLETE
5-66
WHEEL-FRONT DRIVE, GEAR
1
2
5
6
7
3
8
4
9
21
20
19
11
10A
10B
12
13
14
16
18
5-67
15
17
86037660 CHARIOT 02/21/09
22
WHEEL-FRONT DRIVE, GEAR
REF
1
2
3
4
5
6
7
8
9
10A
10B
11
12
13
14
15
16
17
18
19
20
21
PART NO.
86275190
86010790
86002830
86006170
86223980
86219420
86223480
86224020
86317190
86011120
86259920
86224440
86222720
86225810
86279710
86136640
86222770
86279690
86277340
86223980
86318830
86222760
PRV NO.
70377
87163
27196
66031
09134
41510
67450
730233
89262
89273
730387
620037
87506
87245
70262
620042
87243
70830
09134
620041
QTY
4
4
1
1
3
1
2
1
1
1
1
1
1
1
1
1
1
4
4
3
10
1
DESCRIPTION
SCR, 3/8-16 X 1.25 HHCS SS
WASHER, 3/8 SPLIT LOCK PLTD
CABLE TIE, .375 X 24.7
PIN, ROLL 1/8” X 3/4”L
SEALED BALL BRNG, 25MM X 52MM
HUB STEERING
RING, 52MM INTERNAL SNAP
SHAFT ASM, DRIVE PIVOT
GEAR BOX DRIVE UNIT HELICAL
WHEEL, 10 X 2, 5 X 1.06 W/KEYWAY
WHEEL, 10 X 2. 5 W/KEYWAY, GRY
SPACER, 25.51 ID X 45 OD X 39.1 L
PLATE, BEARING RETAINERX
WASHER, ANTI-ROTATION
WASHER, M8 (2THK X 26 OD)
SCR, M8-1.25 X 20 HHMS PLTD
PLATE, BEARING COVER
WASHER, M6 SPLIT LOCK BLK
SCR, M6 X 15 HHCS BLK
SEALED BALL BRNG, .25MM X 52MM
SCR, M10 X 30 SHCS
PLATE, DRIVE YOKE RH
22
86317200
-
1
DRIVE MOTOR ASSEMBLY HELICAL
-
86216210
53820
-
BRUSH SET MOTOR, 53810 86005510
SERIAL NO.
FROM
NOTES:
OPTION
WHEEL NOT
INCLUDED
*SEE SERIAL NUMBER PAGE.
86037660 CHARIOT 08/19/09
5-68
WHEEL-FRONT BRAKE
1
2
20
3
19
18
16
17
14
15
10
11
13
12
4
21
7
8
6
9
5-69
86037660 CHARIOT 02/21/09
5
WHEEL-FRONT BRAKE
REF
PART NO.
PRV NO.
QTY
1
86010790
87163
4
2
3
4
5
86275190
86006170
86005810
86318830
70377
66031
57245
-
4
1
2
1
6
86233410
81270
1
7
86005710
57105
4
8
86273740
70010
2
9
86008920
80889
2
10
11
12
13
86257490
86006840
86010630
86273340
76155
70390
87013
00-000289
2
2
2
4
14
86001740
140816
1
15
16
17
18
19
20
21
86270990
86301950
86264930
86301960
86010650
86274290
86320870
57090
3
1
1
1
3
3
1
27050
87018
70162
-
DESCRIPTION
WASHER, 3/8 SPLIT LOCK
PLTD
SCR, 3/8-16 X 1.25 HHCS SS
PIN, ROLL 1/8” X 3/4”L SS
NUT, 1/4-20 HEX NYLOCK SS
SCR, M10 X 30 SHCS
CLAMP, 3/4 DIA CUSHION
.406DIA
NUT, 1/4-20 HEX W/STAR
WASHER
SCR, 1/4-20 X 1.50 HHCS
BOOT, RUBBER TERM.
ISOLATOR
TERMINAL MOUNT
SCR, 1/4-20 X 1 FHCS PLTD
WASHER, 1/4 ID X 5/8 OD SS
SCR, 8-32 X 3/8 SHCS SS
BRAKE, 36VDC
W/CONNECTOR
NUT, 10-32 HEX NYLOCK SS
PLATE, BRAKE SPACER
CABLE TIE, 3.5” UL/CSA
SKIRT, BRAKE
WASHER, #10 X 9/16 OD
SCR, 10-32 X 3/8 PPHMS SS
SWITCH, 36V BRAKE
SERIAL NO.
FROM
NOTES:
*(24)
*(24)
*(24)
*(24)
*(24)
* SEE SERIAL NUMBER PAGE.
86037660 CHARIOT 08/19/09
5-70
WHEEL-REAR
1A
1B
2
3
5-71
86037660 CHARIOT 04/07/07
WHEEL-REAR
REF
1A
1B
PART NO.
86011110
86259930
PRV NO.
89261
89274
QTY
2
-
2
3
86008710
86232130
80623
17309
2
2
DESCRIPTION
WHEEL, 10X2.5X.787ID BEARINGS
WHEEL, 10X2.5, W/BEARINGS, GRY
RING, ¾” EXT SNAP H-D
CAP, 2.75 ID X 1.0 L BLK VINYL
86037660 CHARIOT 04/07/07
SERIAL NO.
FROM
NOTES:
OPTIONAL
5-72
WIRING-BATTERIES
2
3
4
1A
1B
20A
20B
20C
5
9
24
25
23
7A
7B
6A
6B
10
11
26
8
12
22
13
14
15
16
19
17
18
5-73
86037660 CHARIOT 02/20/07
WIRING-BATTERIES
REF
1A
1B
2
3
4
5
6A
6B
7A
7B
8
9
10
11
12
13
14
15
16
17
18
19
20A
20B
20C
21A
21B
22
23
24
25
26
PART NO.
86260200
86002510
86008920
86271910
86010670
86264960
86260610
86002570
86260230
86002580
86008760
86229700
86008300
86008410
86272810
86092910
86254990
86278150
86259910
86088790
86276070
86270830
86228410
86283410
86228430
86284090
86000150
86005810
86233360
86273980
86010650
86270890
PRV NO.
80872
23125
80889
57295
87029
27915
880836
23190
80876
23191
80682
08071
78242
78568
67132
51396
730313
70117
89265
78571
70593
57023
10023
10030
10032
02456
02264
57245
28038
70066
87018
57034
QTY
2
2
6
6
6
2
1
1
1
1
1
3
1
1
1
1
1
8
8
2
4
4
3
3
3
1
1
8
1
1
1
1
DESCRIPTION
WIRE, 4X14.5BK 3/8RINGX3/8RING
CABLE ASM, BAT. JUMPER X 15”
BOOT, RUBBER TERM. ISOLATOR
NUT, 5/16-18 FLEXLOCK
WASHER, 5/16 FLAT SS
CABLE TIE, .375 X 43”
WIRE, 4X25RD CTERM X 3/8RING
WIRE, 4X27 RD BCLAMP X CTERM
WIRE, 4X30 BK CTERM X 3/8RING
WIRE, 4X27 BK BCLAMP X CTERM
CONN, 175 DCA GRY W/O TERMS
BLOCK, 3.0 X 1.5 X 1.5
TRAY, BATTERY LINER
TRAY, BATTERY
RING, 1/2 EXT. SNAP H-D
LATCH ROD, BATTERY TRAY
SPRING, COMP, 63ODX3.5LX.047W
SHOULDER BOLT, 5/16 OD X 1.0 L
WHEEL, BATTERY TRAY
TRAY, STANDARD STOP
SCR, 5/16-18 X 3/4 CARRIAGE SS
NUT, 5/16-18 HEX NYLOCK SS
BATTERY, 12V, 205AH
BATTERY, 12V, 225AH
BATTERY, 12V, AGM 198AH
CHARGER, 36V, 20A, 115V, C175
CHARGER, 36VDC/21A AGM
NUT, 1/4-20 HEX NYLOCK SS
CLAMP, CABLE KIT SY945
SCREW, 10-32 X 3/4 PPHMS SS
WASHER, #10 X 9/16 OD
NUT, ACORN 10-32
SERIAL NO.
FROM
NOTES:
*(20)
▲
▲
*(12)
▲NOT SHOWN – FOR WET CELL BATTERIES AND AGM BATTERIES
* SEE SERIAL NUMBER PAGE
86037660 CHARIOT 10/20/08
5-74
WIRING-COMPONENTS
2
1
3 4
6
4
5
7
8
9
10
11
13
12
5-75
86037660 CHARIOT 02/03/09
WIRING-COMPONENTS
REF
1
2
3
4
5
6
7
8
9
10
11
12
13
PART NO.
86010780
86273830
86255910
86005710
86010630
86006850
86008920
86238500
86276070
86239720
86233410
86270830
86010670
PRV NO.
87162
70020
73659
57105
87013
70393
80889
81427
70593
41520
81270
57023
87029
QTY
2
2
2
4
2
2
2
1
1
1
1
1
1
DESCRIPTION
WASHER, 1/4 SPLIT LOCK PLTD
SCR, 1/4-20 X 1/2 HHCS SS NP
STANDOFF, 1/4-20 X 1.0 HEX INS
NUT, 1/4-20 HEX W/STAR WASHER
WASHER, 1/4 ID X 5/8 OD SS
SET SCR, 1/4-20 1.25L
BOOT, RUBBER TERM. ISOLATOR
GROMMET, 1.703IDX2.5ODX.125GRV
SCR, 5/16-18 X 3/4 CARRIAGE SS
HORN, 108DB MINIATURE PIEZO
CLAMP, 3/4 DIA CUSHION .406DIA
NUT, 5/16-18 HEX NYLOCK SS
WASHER, 5/16 FLAT SS
86037660 CHARIOT 01/03/08
SERIAL NO.
FROM
NOTES:
5-76
WIRING-CONTROL PANEL-BASIC-CYLINDRICAL
41 BLK
40 RED
32 RED
42 BLK
30 GRN
12 ORG
E
F G
30A-BASIC
25A CYLINDRICAL
52 RED
2 BLK
1 WHT
10 RED
10 RED
18A
10 RED
18A
10 RED
35 RED
3A
34 RED
53 RED
3 LT BLU
M
4
25 GRN
24 YLW
14 WHT/RED
6 RED
24 YLW
26 GRN
3A
14 WHT/RED
30A
6 RED
27 GRN
49 LT BLU
12 ORG
B C D
35 RED
50 ORG
48 BLK
42 BLK
63 BLK
45 WHT
44 WHT
20 WHT
43 RED
6 BRN
9 BRN
47 RED
22 RED
22 RED
23 BLK
23 BLK
18 LT BLU
29 BLU
47 RED
46 RED
58 BLK
17 WHT/YLW
28 GRY
33
23 BLK
22 RED
46 RED
36 RED
6
8 BLK
43 RED
54 BLK
13 BLK
38 BLK
55 BLK
60 BLK
23 BLK
41 BLK
62 BLK
39 BLK
48 BLK
11 BLU
L
32 RED
4 RED
44 WHT
32 RED
19 WHT/BLK
10 RED
49 LT BLU
50 ORG
37 RED
14 WHT/RED
21 LT BLU
1
H
51 RED
A
54 BLK
53 RED
1 WHT
2 BLK
45 WHT
BRUSH
RELAY
55 BLK
3
4
J
22 RED
51 RED
9 RED
52 RED
40 RED
33 RED
7
STATUS LED
BLK
4
K
DIAGRAM B
DIAGRAM D
DIAGRAM C
10 RED
10 RED
24 YLW
2
34 RED
5
WHT
DIAGRAM A
39 BLK
MAIN
RELAY
I
DIAGRAM E
8 BLK
21 LT BLU
57 RED
30 DK GRN
18 WHT/ ORG
7 GRN
9 RED
11 BLK
11 BLK
31 RED
16 LT BLU
5 ORG
13 BLK
DIAGRAM G
DIAGRAM F
3 BLU
4
3
4 RED
6
1
7 GRN
6 BRN
5 ORG
61 RED
4
3
59 RED
56 BLK
6
1
62 BLK
60 BLK
57 RED
6
12
1
19 WHT/BLK
6 BRN
63 BLU
17 WHT/YLW
12 ORG
DIAGRAM I
DIAGRAM H
29 BLU
38 BLK
36 RED
37 RED
86261250
PRV 29273
15 YLW
DIAGRAM L
7
20 WHT
6 BRN
29 DK BLU
14 WHT/RED
15 YLW
18 WHT/ORG
6 BRN
28 GRY
DIAGRAM J
MAIN
RELAY
BRUSH
RELAY
58 BLK
33
86251490
PRV 67619
28 GRY
DIAGRAM K
DIAGRAM M
MAIN
RELAY
86261210 PRV 29204
5-77
86261210 PRV 29204
86037660 CHARIOT 07/30/08
86261210 PRV 29204
WIRING-CONTROL PANEL- BASIC - CYLINDRICAL
REF
1
2
3
4
5
6
7
PART NO.
86239140
86260540
86010860
86261210
86261250
86251490
86311210
PRV NO.
41524
880426
880353
29204
29273
67619
-
QTY
1
1
1
3
1
1
1
DESCRIPTION
HARNESS, CONTROL PANEL BASIC
WIRE, 4X13 RD C.TERM X 5/16RING
WIRE, 4X20 BK CTERM X5/16RING
DIODE ASM, 76008, 76008
DIODE ASM, FAST RECOVERY
RESISTOR ASM, 1/2 WATT 33 OHM
LIGHT ASM, INDICATOR, CODE
SERIAL NO.
FROM
NOTES:
*(8)
*(18)
* SEE SERIAL NUMBER PAGE
86037660 CHARIOT 05/27/08
5-78
WIRING-CONTROL PANEL-DELUXE
5-79
86037660 CHARIOT 03/03/09
WIRING-CONTROL PANEL-DELUXE
REF
1
2
3
4
PART NO.
86260560
86260550
86260570
86239150
PRV NO.
880428
880427
880429
41525
QTY
1
1
1
1
5
86235780
34164
2
DESCRIPTION
WIRE, 4X10RD 5/16RING X 5/16RING
WIRE, 4X15BK C. TERM X 5/16 RING
WIRE, 4X8RD C. TERM X 5/16RING
HARNESS, CONTROL PANEL DELUXE
FERRITE CLAMP, 1.14 X 1.28 X .583
86037660 CHARIOT 01/18/08
SERIAL NO.
FROM
NOTES:
CSXE24 &
CSXEO24 ONLY
5-80
WIRING- DRIVE MOTOR
RED
BLK
1 WHT
2 BLK
1
2 BLK
1 WHT
2 BLK
WHT
BLK
CONTROL PANEL
HARNESS
5-81
86037660 CHARIOT 11/09/06
WIRING-DRIVE MOTOR
REF
1
PART NO.
86239120
PRV NO.
41522
QTY
1
DESCRIPTION
HARNESS, CHARIOT PROPEL
86037660 CHARIOT 11/09/06
SERIAL NO.
FROM
NOTES:
5-82
WIRING-MAIN HARNESS
DIAGRAM A
HORN
13 ORG
12 ORG
17 WHT/YLW
20 BLK
6 BRN
22 WHT/BLK
16 BLK
14 BLK
19 WHT
BRAKE
20 BLK
DRIVE
MOTOR
6 BRN
6 BRN
SOLENOID
VALVE
1
11 RED
DIAGRAM B
59 WHT/ORG
16 BLK
60 WHT/BLK
15 YLW
SWITCH
BRUSH MOTOR
(BASIC ONLY)
10 BLK
13 BLK
18 LG BLU
19 WHT
6 BRN
21 WHT/ORG
15 YLW
12 RED
5
RIGHT
BRUSH
MOTOR
LEFT
BRUSH
MOTOR
PUMP
9 BLK
2
DIAGRAM C
17 LT BLU
18 WHT/YLW
SCRUB LIFT
ACTUATOR
CONTROL
HARNESS
11 RED
3
59 WHT/ORG
60 WHT/BLK
VAC
MOTOR
10 BLK
CONTROL
HARNESS
DELUXE
CONTROL
HARNESS
BASIC
D
DIAGRAM D
A
B
10 BLK
SQUEEGEE LIFT
ACTUATOR
(DELUXE ONLY)
5-83
4
22 WHT/BLK
21 WHT/ORG
C
11 RED
VACUUM
SWITCH
(BASIC ONLY)
86037660 CHARIOT 11/09/06
WIRING-MAIN HARNESS
REF
1
2
3
4
5
PART NO.
86239170
86239130
86239160
86239110
86235820
PRV NO.
41528
41523
41527
41521
34376
QTY
1
1
1
1
1
DESCRIPTION
HARNESS, BRAKE
HARNESS, MAIN
HARNESS, DECK SWITCH
HARNESS, VAC BASIC
FERRITE, .72 X .70 X 1.28
86037660 CHARIOT 11/09/06
SERIAL NO.
FROM
NOTES:
BASIC ONLY
BASIC ONLY
CSE24 ONLY
5-84
WIRING-PEDAL PLATFORM
B
A
1
BRN
BLU
BRN
RED
DIAGRAM A
DIAGRAM B
5 ORG
6 BRN
7 GRN
5 GRN
10 BRN
6 ORG
3 LT BLU
4 RED
5-85
5-65
86037660 CHARIOT 11/09/06
WIRING-PEDAL PLATFORM
REF
1
PART NO.
86218810
PRV NO.
23717
QTY
1
DESCRIPTION
HARNESS, TWISTER PEDAL
86037660 CHARIOT 11/09/06
SERIAL NO.
FROM
NOTES:
5-86
5-87
BLK
21/LT-BLU
51/RED
9/RED
34/RED
86310910
BRUSH
RELAY
52/RED
SOLUTION
CONTROL
BOARD
39/BLK
33/RED
WHT
WHT
INDICATES OPTIONAL
EQUIPMENT
INDICATES WIRING
NOT IN HARNESS
86037660 CHARIOT 07/30/08
32/RED
32/RED
36/RED
61/RED
SHUNT
38/BLK
6/BRN
6/BRN
42/BLK
63/BLK
34/RED
35/RED
3/LT-BLUE
53/RED
20/WHT
52/RED
47/RED
15/YLW
14/WHT-RED
50/ORG
AMP
METER
40/BLK
SPEED
SWITCH
30/GRN
TRACTION
26/GRN
27/GRN
48/BLK
RUN/RESET
RELAY
36/RED
KEY
SWITCH
RESET
SWITCH
19/WHT-BLK
44/WHT
43/RED
45/WHT
4/RED
12/ORG
BATTERY
METER
32/RED
25/GRN
100K
FORWARD/REV
SWITCH
200K
58/BLK
29/BLU
28/GRY
220K
56/RED
59/RED
19/WHT-BLK
60/BLK
13/ORG
5/ORG
6/BRN
7/GRN
4/RED
3/LT-BLUE
58/BLK
57/RED
62/BLK
61/RED
59/RED
14/BLK
6/BRN
6/BRN
20/BLK
19/WHT
16/BLK
15/YLW
22/WHT-BLK
21/WHT-ORG
13/BLK
12 PIN DEUTSCH
12/ORG
6/BRN
6/BRN
63/BLK
20/WHT
15/YLW
14/WHT-RED
18/WHT-ORG
17/WHT-YLW
18/LT-BLU
6 PIN
DEUTSCH
41/BLK
16/LT BLU
17/WHT-YLW
BLK
30/BLK
29/RED
26/BLK
23/RED
32/BLK
31/RED
RED
9/BLK
12/RED
VAL
SWITCH
36/RED
37/RED
49/LT-BLU
47/RED
2/BLK
1/WHT
2 PIN DEUTSCH
2 PIN DEUTSCH
RED
2 PIN DEUTSCH
2 PIN DEUTSCH
DECK LIFT
ACTUATOR
37/RED
VACCUM
30A
50/ORG
BRUSH
18A
46/RED
14/WHT-RED
8/BLK
9/RED
11/BLK
10/RED
TRACTION
10/RED
PUMP
3A
53/RED
9/RED
BRUSH
18A
54/BLK
2/BLK
1/WHT
5/ORG
7/GRN
18/WHT-ORG
30/GRN
10/BLK
11/RED
BLK
BLK
LBRUSH
40/RED
22/RED
14/WHT-RED
29/BLU
6/BRN
46/RED
2 PIN DEUTSCH
RBRUSH
31/RED
57/RED
24/YLW
SOLUTION
CONTROL
POTENTIOMETER
28/GRY
BLK
DECK
ACTUATOR
11/BLK
10/RED
10/BLK
11/RED
SOLENOID
21/LT BLU
22/RED
23/BLK
17/WHT-YLW
18/LT BLU
WIRING DIAGRAM-BASIC-CYLINDRICAL
VACUUM
DECK
SWITCH
OPERATOR PLATFORM
SOLUTION
PUMP
4 PIN
DEUTSCH
PLATFORM
SWITCH
OPERATION
PRESENT
SWITCH
4 PIN
DEUTSCH
6 PIN
DEUTSCH
THROTTLE
POT
HEADLIGHT
SWITCH
32/RED
40/RED
WIRING DIAGRAM-DELUXE
OPERATOR PLATFORM
SOLENOID
PLATFORM SWITCH
RBRUSH
BRAKE
SWITCH
BRAKE
VACUUM 1
LBRUSH
BLU
RED
OPERATOR
PRESENCE
SWITCH
DECK LIFT SQUEGEE SOLUTION
ACTUATOR ACTUATOR PUMP
BRN
FLASHER
UNIT
ORG
BRN
GRN
4 PIN
DEUTSCH
TRACTION
2 PIN PACKARD
12 PIN DEUTSCH
10/BLK
12/RED
7/GRN
9/RED
5/ORG
58/BLU
4/RED
16/LT BLU
17/WHT-YLW
19/WHT-BLK
18/WHT-ORG
14/WHT-RED
15/YLW
20/WHT
63/BLK
6/BRN
6/BRN
13/BLK
12/ORG
57/WHT
8/BLK
6/BRN
2/BLK
6 PIN
DEUTSCH
38/BLK
37/BLU
26/RED
25/BLK
39/RED
58/BLK
2 PIN PACKARD
2 PIN PACKARD
THROTTLE POT
18/LT-BLU
17/WHT-YLW
21/WHT-ORG
22/WHT-BLK
15/YLW
16/BLK
19/WHT
20/BLK
6/BRN
6/BRN
14/BLK
13/ORG
31/RED
32/BLK
23/RED
26/BLK
29/RED
30/BLK
6 PIN
DEUTSCH
HORN
4 PIN
DEUTSCH
10/BLK
11/RED
40/RED
2W 220
41/RED
RES
19/WHT
LCD
EMERGENCY STOP
3/BLU
HORN
36/RED
31/RED
SPEED
55/LT-BLU
ONE
TOUCH
51/LT-BLU
51/LT-BLU
VACUUM
50/GRN
RUN/RESET
RELAY
42/BLK
20/BLK
6/BRN
6/BRN
18 AMP
BREAKER
BRUSH
51/DK-BLU
52/ORG
WATER
FLOW
53/LT-BLU
51/DK-BLU
54/WHT
BRUSH
PRESS
46/BLK
INFO
49/YLW
48/LT-BLU
51/DK-BLU
34/YLW
HEAD
LIGHT
SWITCH
18 AMP
BREAKER
BRUSH
43/GRN
4/RED
19/WHT
44/GRN
FWD/REV
SWITCH
26/RED
33/ORG
13/ORG
40/RED
KEY
45/WHT-BLU
1
7
1
FERRITE
BEAD
2/BLK
1/WHT
24/RED
42/BLK
14/BLK
23/BLK
25/BLK
RESET SWITCH
4/RED
4/RED
30 AMP
BREAKER
TRACTION
1/WHT
10/BLK
FERRITE
BEAD
10
57/WHT
3/BLU
58/BLU
11/RED
1
8/BLK
2
9/RED
1
34/YLW
38/BLK
37/BLU
39/RED
35/LT-GRN
33/ORG
36/LT-BLU
41/RED
24/RED
NC NO C
3
VACUUM
BRUSH
INDICATES OPTIONAL EQUIPMENT
18/LT-BLU
17/WHT-YLW
21/WHT-ORG
22/WHT-BLK
15/YLW
16/BLK
27/BLU
30/WHT
28/0RG
31/RED
29/BLK
32/GRN
125 AMP
FUSE
BATTERY
CONN
36v
86037660 CHARIOT 03/03/09
5-88
86282190 (13")
PRV 39616
DRAIN HOSE
86004310 (18")
PRV 39505
HOSE DIAGRAM - DISK
TANK
SHUT-OFF
VALVE
80 MESH (FINE)
STRAINER
86281950 (32")
PRV 39541
SOLENOID
VALVE
86281100 (8")
PRV 39274
86281310 (8")
PRV 39326
86281310 (8") PRV 39326
86281940 (40")
PRV 39540
PUMP
12 MESH (COARSE)
STAINER
SCRUB DECK
5-89
86037660 CHARIOT 01/03/08
DRAIN HOSE
86004310 (18")
PRV 39505
HOSE DIAGRAM - CYLINDRICAL
SHUT-OFF
VALVE
12 MESH (COARSE)
STAINER
86281940 (40")
PRV 39540
86282370 (58")
PRV 39735
80 MESH (FINE)
STRAINER
PUMP
86282360 (28")
PRV 39734
TANK
PRV 39282
SOLENOID
VALVE
86281100
PRV 39274
86037660 CHARIOT 01/03/08
5-90
SUGGESTED SPARE PARTS
PART NO.
86001910
86001920
86002000
86002010
86232130
86003680
86004010
86305960
86004860
86004890
86006340
86251410
86007140
86007170
86007190
86007240
86008790
86009200
86009700
86069880
86001510
86001520
86001540
86001560
86001570
86001580
86001630
86001700
86001730
86001740
86002730
86231560
86002780
86007940
PRV NO.
14606
14607
14717
14942
17309
34380
35274
48073
48095
66347
67506
72130
72159
72161
72190
80687
81535
82267
140534
140712
140752
140753
140754
140755
140763
140764
140780
140804
140816
270085
270097
270098
73836
86256120
86313170
730368
-
5-91
DESCRIPTION
BREAKER, 30A 50VDC CIRCUIT
BREAKER, 25BA 50VDC CIRCUIT
BREAKER, 3 AMP 1681-090-300
BOOT, 3/8 CIRCUIT BREAKER
CAP, 2.75 X 1.0L BLACK VINYL
FLOAT, SHUT OFF
GASKET, DOME EDGE
HOSE ASM., 1.5” BLK PVC VAC X 67
KEY, SWITCH
KNOB, ALUM 3/8-16 NYLOCK NUT SS
RECOVERY DRAIN PLUG 1-3/4
RELAY, 15A 36V MINI
SWITCH, SPST 2-POSITION ROCKER
SWITCH, 2 POSITION KEY
SWITCH, DPST KEY
SWITCH, SEALED PB ROUND
FUSE, 125 AMP
KNOB, 3/8-16 4 PRONG ALUM
PLUG, 5/8” DRAIN HOSE
BRKT, CABLE ATTACH
BAG, INNER TANK
BLADE, AQUAMIZER, 12IN LEFT
BLADE, AQUAMIZER, 12IN RIGHT
BLADE, SKIRT, SCRUB DECK, 24 IN LEFT
BLADE, SKIRT, SCRUB DECK, 24 IN RIGHT
BLADE, SQG REAR 40.6IN LINATEX
BLADE, SQG FRONT 36.7IN RED GUM
BLADE, SKIRT, SCRUB DECK, FRONT
BREAKER, 18A 250VAC, 50VDC
BRAKE, 36 VDC W/CONNECTOR
CHAIN, ISO 08B 12.7 MM PITCH
CABLE, SQUEEGEE LIFT BASIC
CABLE, SQUEEGEE LIFT DELUXE
STRAINER, DEEP, 100 MESH
STRAINER, 1/2 FPT 100 MESH
CAP, STRAINER TALL
86037660 CHARIOT 10/13/08
SERIAL NO.
FROM
NOTES:
BASIC ONLY
BASIC ONLY
BASIC ONLY
BASIC ONLY
DELUXE ONLY
DELUXE ONLY
DISK ONLY
CYLINDRICAL
ONLY
OPTIONS
BACK-UP ALARM - OPTION
3
1
2
4
6-1
86037660 CHARIOT 11/09/06
BACK-UP ALARM - OPTION
REF
1
2
3
4
PART NO.
86071140
86231500
86276780
86271840
PRV NO.
140817
80882
70728
57285
QTY
1
1
1
1
DESCRIPTION
BRKT, BACK UP ALARM
BUZZER, PIEZO 6-28VCD
SCR, 5/16-18 X 3/4 HHCS SS
NUT, 5/16-18 HEX NYLOCK THN SS
86037660 CHARIOT 11/09/06
SERIAL NO.
FROM
NOTES:
6-2
BATTERY CART - OPTION
27
26
28
3
30
5
24
3
8
9
29 25
2
6
1
2
15
3
4
3
23
3
22
5
10
5
3
3
6
9 8
7
13
12
5
3
14
20
11
21
19
16
15
18
17
6-3
31
3
86037660 CHARIOT 09/17/09
3
BATTERY CART - OPTION
REF
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
PART NO.
86006930
86254290
86270830
86077010
86010670
86228840
86259410
86259400
86254890
86068490
86231090
86083120
86076600
86004070
86276790
86276690
86199430
86078890
86277130
86007020
86232590
86001350
86011020
86271840
86008130
86274730
86070790
86087340
86070800
86271870
86276070
PRV NO.
70514
730338
57023
41517
87029
09124
87206
730331
730018
140019
80809
66442
38318
36196
70732
70715
040-03
620020
70795
70673
18032
140390
89202
57285
73958
70265
140737
730339
140738
57290
70593
QTY
2
4
33
1
7
3
1
4
3
1
1
1
2
2
4
7
2
8
16
1
2
2
2
2
2
2
2
2
2
2
1
DESCRIPTION
SCR, 5/16-18 X 1.00 BSHCS SS
SPACER, 10D X .343ID, .5 LG
NUT, 5/16-18 HEX NYLOCK SS
HOUSING, BATTERY CART
WASHER, 5/16 FLAT SS
BEARING, FLANGED .314D X .502OD
WASHER, THRUST, .51 ID X 1 OD X .063
WASHER, THRUST .51 ID X 1 OD
SPRING, EXT, .50D X 4.0L
BRKT, TRAY CATCH
BUMPER, RUBBER 5/16" ID X 1.50
PLATE, BATTERY CART BACK
HANDLE, BATTERY CART
GRIP, POLISHER HANDLE
SCR, 5/16-18 X 1.75 HHCS SS
SCR, 5/16-18 X 1.75 CARR SS
CASTER SWIVEL 4” 250# CPCTY
PLATE, CASTER SPACER
SCR, 5/16-18 X 1.00 CARRIAGE SS
SP SCR, 5/16-18 X 1.25 HHCS SS NP
CASTER, 4” HARD RUBBER RIGID
BUSHING, SPANNER .435 X 1.10
WHEEL, 3” DIA CUSHION RUBBER
NUT, 5/16-18 HEX NYLOCK THIN SS
SPACER, 3/8OD X .62W X .312L, AL
SCR, 1/4-20 X 3/4 SHCS PLTD
BRKT, BATTERY LOCK MOUNT
SPACER, LATCH GUIDE
BRKT, BATTERY TRAY LOCK
NUT, 1/4-20 HEX NYLOCK THIN SS
SCR, 5/16-18 X 3/4 CARRIAGE SS
86037660 CHARIOT 09/17/09
SERIAL NO.
FROM
NOTES:
6-4
BATTERY CART - OPTION
1
2
4
5
3
7
7
5
6
10
3
6
17
3
8
9
10
11
12
13
14
15
6
10
10
3
16
6-5
86037660 CHARIOT 11/09/06
3
BATTERY CART - OPTION
REF
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
PART NO.
86078330
86276070
86270830
86087800
86228840
86259410
86006560
86077140
86226830
86010670
86244280
86276060
86254280
86231150
86259400
86276690
86077530
PRV NO.
66478
70593
57023
730307
09124
87206
70083
51404
73268
87029
500934
70590
730331
09151
87205
70715
51403
QTY
1
2
12
2
4
6
4
2
2
10
1
4
12
4
8
16
2
DESCRIPTION
PEDAL, BATTERY CART
SCR, 5/16-18 X 3/4 CARRIAGE SS
NUT, 5/16-18 HEX NYLOCK SS
STIFFENER, PEDAL, BATTERY CART
BEARING, FLANGED .314ID X .502OD
WASHER, THRUST .51 ID X 1 OD X .063
SCR, 5/16-18 X 1 HHCS SS
LATCH, BATTERY CART
SPRING, EXT .68D X 3.00L X .098W
WASHER, 5/16 FLAT SS
LABEL, BATTERY CART OPERATION
SCR, 5/16-18 X 2.5 CARR GR5
SPACER, 1.00 ODX .32ID X .375
BUSHING FLANGE, .314 X .502 OD
WASHER, THRUST .51 ID X 1 OD
SCR, 5/16-18 X 1.75 CARR SS
LINKAGE, LATCH, BATT CART
86037660 CHARIOT 11/09/06
SERIAL NO.
FROM
NOTES:
6-6
SEAT - OPTION
2
13
14
1
12
11
3
4
5
6
10
9
8
7
15
16
17
18
19
20
23
24
22
21
6-7
86037660 CHARIOT 11/09/06
SEAT - OPTION
REF
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
PART NO.
86248390
86082640
86276890
86279460
86270710
86271930
86278910
86070830
86070840
86277710
86008650
86246320
86272300
86251860
86279620
86276070
86277510
86009200
86254300
86094000
86276710
86093790
86010670
86270830
PRV NO.
730324
629995
70752
87164
01-000277
57297
87003
140742
140743
730347
80604
51142
66133
66481
87200
70593
70857
81535
730350
05246
70717
05247
87029
57023
QTY
1
1
4
2
1
1
3
1
1
1
1
1
1
1
2
2
1
1
1
1
2
1
4
4
DESCRIPTION
PAD, REAR REST
PLATE, SEAT COVER
SCR, 5/16-18 X 3/4 PTHMS SS
WASHER, 1/2 SPLIT LOCK
NUT, WING 3/8-16
NUT, 3/8-16 HEX NYLOCK SS
WASHR, 3/8 ID X 7/8 OD SS
BRKT, LEFT REAR SEAT
BRKT, RIGHT REAR SEAT
SCR, 3/8-16 X 2.75 HHCS SS
COTTER, 1/4” RING
LEVER, HANDLE LOCK
PIN, CLEVIS 3/16 X .88 PLTD
ROD, ARM HANDLE LOCK 4” LG
WASHER, .4ID X 1.3OD NYLON
SCR, 5/16-18 X 3/4 CARRIAGE SS
SCR, 3/8-16 X 5.0 HHCS SS FT
KNOB, 3/8-16 4 PRONG ALUM
SPACER, SEAT LOCK
SEAT MOUNT POST
SCR, 5/16-18 X 2.0 CARRIAGE SS
RECEIVER ASSY, SEAT MOUNT
WASHER, 5/16 FLAT SS
NUT, 5/16-18 HEX NYLOCK SS
86037660 CHARIOT 11/09/06
SERIAL NO.
FROM
NOTES:
6-8
WARNING LIGHTS - OPTION
1
6
2
3
3
4
FRONT
5
7
3
1
2
6
6-9
REAR
86037660 CHARIOT 11/09/06
WARNING LIGHTS - OPTION
REF
1
2
3
4
5
6
7
PART NO.
86270990
86010650
86276820
86071490
86270990
86246200
86071500
PRV NO.
57090
87018
70740
140871
57090
51454
140872
QTY
4
4
4
1
2
2
1
DESCRIPTION
NUT, 10-32 HEX NYLOCK SS
WASHER, #10 X 6/16 OD
SCR, 10-32 X 1/2 PTHMS BLK
BRKT, UPPER WARNING LIGHT
NUT, 10-32 HEX NYLOCK SS
LED AMBER LIGHT, 12V
BRKT, LOWER WARNING LIGHT
86037660 CHARIOT 11/09/06
SERIAL NO.
FROM
NOTES:
6-10
6-11
86037660 CHARIOT 11/09/06
86037660 CHARIOT 11/09/06
6-12
6-13
86037660 CHARIOT 11/09/06
SERIAL NUMBERS
REF.
NO.
1
MODEL: SERIAL #
CS24, CSE24, CSX24, CSXE24, CSXE024, CSE24SP, CS24SP : 1000170494
2
CS24, CSE24, CSX24, CSXE24, CSXE024, CSE24SP, CS24SP : 1000140332
3
CS24, CSE24, CSX24, CSXE24, CSXE024, CSE24SP, CS24SP : 1000143553
4
CS24, CSE24, CSX24, CSXE24, CSXE024, CSE24SP, CS24SP : 1000143906
5
CS24, CSE24, CSX24, CSXE24, CSXE024, CSE24SP, CS24SP : 1000144785
6
CS24, CSE24, CSX24, CSXE24, CSXE024, CSE24SP, CS24SP : 1000149450
7
CS24, CSE24, CSX24, CSXE24, CSXE024, CSE24SP, CS24SP : 1000149664
8
CS24, CSE24, CSX24, CSXE24, CSXE024, CSE24SP, CS24SP : 1000150256
9
CS24, CSE24, CSX24, CSXE24, CSXE024, CSE24SP, CS24SP : 1000150384
10
CS24, CSE24, CSX24, CSXE24, CSXE024, CSE24SP, CS24SP : 1000151588
11
CS24, CSE24, CSX24, CSXE24, CSXE024, CSE24SP, CS24SP : 1000154281
12
CS24, CSE24, CSX24, CSXE24, CSXE024, CSE24SP, CS24SP : 1000154660
13
CS24, CSE24, CSX24, CSXE24, CSXE024, CSE24SP, CS24SP : 1000155938
14
CS24, CSE24, CSX24, CSXE24, CSXE024, CSE24SP, CS24SP : 1000156273
15
CS24, CSE24, CSX24, CSXE24, CSXE024, CSE24SP, CS24SP : 1000157499
16
CS24, CSE24, CSX24, CSXE24, CSXE024, CSE24SP, CS24SP : 1000157501
17
CS24, CSE24, CSX24, CSXE24, CSXE024, CSE24SP, CS24SP : 1000157685
18
CS24, CSE24, CSX24, CSXE24, CSXE024, CSE24SP, CS24SP : 1000159164
19
CS24, CSE24, CSX24, CSXE24, CSXE024, CSE24SP, CS24SP : 1000159653
20
CS24, CSE24, CSX24, CSXE24, CSXE024, CSE24SP, CS24SP : 1000160355
21
CS24, CSE24, CSX24, CSXE24, CSXE024, CSE24SP, CS24SP : 1000168941
22
CS24, CSE24, CSX24, CSXE24, CSXE024, CSE24SP, CS24SP : 1000170203
23
CS24, CSE24, CSX24, CSXE24, CSXE024, CSE24SP, CS24SP : 10060140000046
24
CS24 : 10060210000104
25
CS24 : 10060210000143
26
CS24 : 10060210000178
27
CSE24 : 10060250000006
28
CSX24 : 10060270000498
29
CSXE24 : 10060290000001
30
CSXE024 : 10060300000001
CSE24: 10060250000007, CSE24SP: 10060260000003, CSXEO24: 10060300000001, CSX24: 10060270000736,
CSX24X: 10060280000078, CS24: 1006021000252, CS24SP: 10060220000080, CS24SPX: 10060230000003,
CS24X 100602400000018
CSX24: 10060270000837, CSXE24: 10060290000028, CSXE024: 10060300000001
CSE24: 10060250000007, CSXEO24: 10060300000001, CSX24: 10060270000837, CSX24X: 10060280000085,
CS24: 1006021000317, CS24X 100602400000024, CSXE24 10060290000029
CS24: 10060210000315, CSX24: 10060270000845, CSXEO24: 10030300000001, CSE24: 10060250000007,
CSXE24: 10060290000029, CS24SP: 10060220000091, CSE24SP: 10060260000003
31
32
33
34
86037660 CHARIOT 04/21/09
6-14