Canon DR-X10C - imageFORMULA - Document Scanner User manual

ENGLISH
Document Scanner DR-X10C
CAUTION
❏ The scanner weights about 39 kg.
To lift or move the scanner, always use two people, one on each side. Never
attempt to lift the scanner by yourself. You could drop the scanner or pinch your
fingers, resulting in personal injury or damage to the scanner. Remember to be
extra careful when moving it.
Easy Start Guide
Thank you for purchasing the Canon imageFORMULA DR-X10C Document Scanner.
Manuals for the Scanner
The documentation for the scanner consists of the Easy Start Guide (this manual) and the
Reference Guide (supplied with the scanner), the User Manual, and the CapturePerfect3.0
Operation Guide, which are provided in electronic form and registered in the menu during
software installation.
Please read this and the following manuals thoroughly before using the scanner to become
acquainted with its capabilities and make the most of its many functions.
After reading the manuals, store them in a safe place for future reference.
Easy Start Guide (This Manual)
This manual describes the procedures for setting up the scanner for use.
Please follow the procedures in the Easy Start Guide to set up the scanner.
After checking the package contents, you need to install the supplied
pickup roller and feed roller. (☞ STEP 2)
Reference Guide
This manual consists of the basic scanner operating instructions extracted
from the User Manual. For more details, refer to the User Manual.
User Manual (Electronic Manual)
This manual consists of two sections: Hardware and Software.
The Hardware section provides general information about the scanner
operational settings, maintenance, and troubleshooting.
The Software section describes how to use the ISIS/ TWAIN driver with the
scanner, and how to set up job registration tools.
CapturePerfect 3.0 Operation Guide (Electronic Manual)
This is the operation guide for CapturePerfect 3.0, the Canon document
scanner application program.
6.
1) and up (2
2) to lock the feed
Push the lock lever for the feed roller to the left (1
roller in place.
7.
Push the roller cover up until it clicks into place.
8.
1). Press down on both sides of the upper unit to
Carefully lower the upper unit (1
2).
ensure that it is securely closed (2
1.
2.
Log on to Windows with Administrator privileges.
Insert the DR-X10C Setup Disc into the
computer’s CD-ROM drive.
The setup menu automatically starts up
when you insert the CD-ROM into the CDROM drive. If the setup menu does not start
up, run the setup.exe application on the
CD-ROM.
When Installing in Windows Vista
When using Windows Vista, the “User
Account Control” dialog box may appear. In
this case, enter your login user password
for Administrator privileges, and click [OK].
3.
The setup menu starts up.
The setup menu consists of the following screens:
Menu Screen
Typical Installation
Installing the Rollers
Install the supplied pickup roller and feed roller in the scanner.
IMPORTANT
●
* Installs all of the software displayed.
The pickup roller and feed roller are installed in the following locations after
opening the upper unit.
Pickup Roller
IMPORTANT
After installing the rollers, you need to install the software.
(☞ STEP 3)
Read Manuals
Custom Installation
* The User Manual and CapturePerfect 3.0
Operation Guide electronic manuals for
the scanner are installed on the computer
with the rest of the software.
* Installs only the selected software.
The electronic manuals are PDF (Portable Document Format) files, and are installed
in the following folders during software installation. (☞ STEP 2)
Installing the Software
Feed Roller
●
Be sure to install the pickup roller and feed roller, as documents will not feed if the
rollers are not installed.
Install the software before connecting the scanner to the computer.
CAUTION
User Manual
CapturePerfect 3.0 Operation Guide
1.
Press the Open/Close button, and carefully raise the upper unit until it stops.
Checking the Package Contents
When you unpack your scanner, make sure all of the following accessories are included.
If any of the items listed below are missing or damaged, contact your local authorized Canon
dealer or service representative.
Open/Close Button
2.
DR-X10C
Power Cord
(Length: 1.5 m)
USB Cable
(Length: 2 m)
Pickup Roller
Feed Roller
Click [Typical Installation].
[Typical Installation] installs the software
(scanner driver, CapturePerfect 3.0) and the
User Manual. The CapturePerfect 3.0
Operation Guide is installed on the
computer during the CapturePerfect 3.0
installation.
5.
Click [Install].
The scanner driver installation wizard
appears. This operation installs both the
scanner driver and the Job Tool.
6.
Click [Next].
7.
Read the software license agreement, and
click [Yes] if you consent to its conditions.
Installation of the scanner driver starts.
8.
Click [Finish] to complete the installation.
Next, the installation wizard for
CapturePerfect 3.0 appears.
9.
Click [Next].
Do not hold the glass portion when opening and closing the roller cover.
ENGLISH
Document Scanner DR-X10C
Easy Start Guide
3.
Avant l’utilisation
Vor dem Gebrauch
Antes de la utilización
Prima dell’uso
Voor gebruik
Easy Start Guide
(This Guide)
Hold the roller cover as shown, and lower it toward you.
❏ Before installing the software, make sure your computer is correctly running one of
the following versions of Windows. For details on system requirements, refer to
“Installation Requirements” on p. 2-3 of the User Manual.
• Windows 2000 Professional SP4 or later
• Windows XP Home Edition SP2 or later
• Windows XP Professional SP2 or later
• Windows XP Professional x64 Edition
• Windows Vista Home Basic (32- and 64-bit versions)
• Windows Vista Home Premium (32- and 64-bit versions)
• Windows Vista Business (32- and 64-bit versions)
• Windows Vista Ultimate (32- and 64-bit versions)
• Windows Vista Enterprise (32- and 64-bit versions)
❏ Do not connect the scanner to the computer before installing the software. If you
connect the scanner and turn it ON before you install the software, a wizard screen
will appear. If this wizard appears, click [Cancel] to exit the wizard, and then turn
the scanner OFF.
Windows 2000
4.
Reference Guide
Before Use
1) in place, and push the mounting lever (2
2) back to
Set the pickup roller (1
secure it.
Software license
agreement
Windows XP
DR-X10C
Setup Disc
Roller Cleaning
Sheets (4)
Cleaning Cloth (1)
Clear Binder (1)
4.
1) and to the right (2
2).
Push the lock lever for the feed roller down (1
IMPORTANT
●
●
●
●
●
●
The cleaning cloth is used for cleaning the scanner’s interior.
The roller cleaning sheets are adhesive sheets (with peel-off protective sheets)
used for removing dust and particles from the transport rollers. Use them when you
enable the scanner’s Cleaning Mode. (Do not remove the protective sheets until
you are ready to use the sheets.)
Items included in this package are subject to change without notice.
Keep the package and packing materials for storing or transporting the scanner.
A print version of Reference Guide is supplied in English. PDF files of the
Reference Guide in other languages can be found on the Setup Disc CD-ROM.
Use the supplied clear binder to store manuals printed from the Setup Disc.
■ Trademarks
• Canon and the Canon logo are registered trademarks of Canon Inc. in the United States and may also be
trademarks or registered trademarks in other countries.
• Microsoft Windows® is a registered trademark of Microsoft USA in the United States and other countries.
• Other brands and product names used in this manual may be trademarks or registered trademarks of their
respective companies.
PUB. CE-IE-586
© CANON ELECTRONICS INC. 2007
5.
Align the notches in the shaft of the feed roller with the pins on the shaft in the
scanner, and place the feed roller into position.
Windows Vista
❏ Close all other applications before installing the software.
☞ Continued on back side
☞ Continued from front side
10. Read the software license agreement, and
Connecting the Power Cord
1. Connect the supplied power cord into the power connector on the back of the
click [Yes] if you consent to its conditions.
1.
2.
1)
scanner. (1
2.
The computer should now recognize the scanner properly.
Next, you need to select the scanner from your application program.
(☞ STEP 6)
Make sure that the scanner and computer are connected properly.
Press the power switch to turn the scanner ON.
The Document Feed Tray opens automatically.
2)
Connect the power cord into an AC outlet. (2
Selecting the Scanner
11. Confirm the installation destination, and
Power Switch
click [Next].
Installation of CapturePerfect 3.0 starts.
When Connecting by USB
3. Use the supplied USB cable to connect the scanner to the computer.
12. Click [Finish] to complete the installation of
3.
4.
Connect the square plug (Type B) of the USB cable to the scanner.
CapturePerfect 3.0.
Next, the installation wizard for the User
Manual appears.
Turn ON the computer.
Windows automatically recognizes the scanner and performs the device driver
installation.
Windows 2000
To use the scanner with an ISIS/TWAIN-compliant application program, the scanner must first
be selected.
The menus and procedures used for selecting scanners vary depending on the application
used. For detailed information on selecting scanners, refer to the user’s manual for your
application.
This section describes how to select the scanner when using CapturePerfect 3.0. For details
on how to use CapturePerfect 3.0, refer to CapturePerfect 3.0 Operation Guide located in the
Windows program menu.
1.
Launch CapturePerfect 3.0 from the Windows program menu.
Type A
Windows XP
13. Click [Next].
CapturePerfect3.0
Windows Vista
Installation of the User Manual starts.
Type B
When Connecting by SCSI
3. Use the SCSI cable to connect the scanner to the computer.
A SCSI cable is not supplied. Acquire a SCSI cable beforehand that matches
the shape of the connectors on your SCSI card and the scanner.
IMPORTANT
●
14. Click [Finish] to complete the installation of
the User Manual.
With Windows Vista, installation proceeds automatically regardless of the displayed
“Check here for status” balloon help.
You can click “Check here for status” to display the installation progress.
2.
15. When all installations are complete, the
●
installation completed screen appears.
Click [Exit] to exit the installer. Click [Back]
to return to the menu screen.
With Windows XP and Vista, a message appears when installation is finished.
Windows XP
The [Select Scanner] dialog box appears.
CAUTION
3.
❏ Observe the following when connecting the scanner with other devices in a “daisy
chain”.
• The SCSI ID of the scanner is set to “SCSI ID = 2” by default. When using a
daisy-chain configuration with other SCSI devices, set the DIP switches so that
SCSI ID numbers are not duplicated in the system.
This completes the software installation.
Next, you need to connect the scanner to your computer. (☞ STEP 4)
Connecting the Scanner to the
Computer
There are two methods for connecting the DR-X10C scanner to a computer: a USB
connection to a standard USB port built in to the computer, or SCSI connection to a SCSI
card installed in an expansion slot of the computer. Select the method that is best suited to
your computer environment.
DIP Switches
The DR-X10C device driver is installed in Device Manager under [Imaging Devices]
as [CANON DR-X10C USB] or [CANON DR-X10C SCSI].
Default Position (SCSI ID=2)
• The DR-X10C scanner incorporates a SCSI terminator which is permanently
set to ON. When using a daisy-chain configuration with other SCSI devices,
make sure that the DR-X10C scanner is connected as the last device in the
chain. Set the terminators of all other devices to OFF.
The scanner is now connected to your computer.
Next, you need to turn on the scanner and ensure Windows
recognizes it. (☞ STEP 5)
Turning the Power ON (Scanner
Recognition)
DIP Switches
for SCSI ID
Power Connector
When you turn ON the computer and the scanner, the Windows Plug and Play function
recognizes the scanner and automatically installs the required device driver.
From the Control Panel, you can display the Device Manager using the following
procedure:
– With Windows 2000, open [System] and click [Device Manager] on the
Hardware tab sheet.
– With Windows XP, first switch the Control Panel to the Classic View to display
[System]. Then open [System] and click [Device Manager] on the Hardware
tab sheet.
– With Windows Vista, open [System Maintenance] and click [Device Manager].
Or, switch the Control Panel to the Classic View and click the [Device
Manager] icon.
● By enabling the User Mode function for Auto USB Power Switch, you can have the
computer’s power switch turn the scanner ON and OFF. For details on User Mode
and USB-linked power switching, refer to the User Manual.
Do not connect both USB and SCSI cables to the scanner at the same time.
Use only the supplied power cord.
The scanner and computer should both be turned OFF when making connections.
Make sure that the computer is turned OFF before connecting the SCSI cable. The
scanner may not be properly recognized by the computer if it is connected while
the computer is turned ON.
❏ A SCSI cable is not supplied with the scanner. Obtain a cable with connectors that
match the SCSI connectors on both the scanner and the computer.
<USB-linked power switch>
CAUTION
❏ When connecting the scanner to the computer using a SCSI cable, be sure to turn
ON the scanner first, and then turn ON the computer. If you turn ON the computer
first, the scanner may not be properly recognized by the computer.
❏ Be sure to log on to Windows using an account with Administrator privileges.
❏ After turning the scanner OFF, wait at least 10 seconds before turning it ON again.
❏ If you will not be using the scanner for an extended period, disconnect the power
cord from the AC outlet for safety.
The [Configure Device Settings] dialog box appears.
4.
Set the default page size.
5.
Click [OK] to finish scanner selection.
●
CAUTION
❏
❏
❏
❏
Select [CANON DR-X10C], and click [Settings].
Windows Vista
●
USB Connector
SCSI Connector
(D-sub, 50-pin
half-pitch)
From the [Scan] menu, select [Select Scanner].
Turning the computer ON or OFF turns the scanner ON (document feed
tray opens) or OFF.
The setup is now complete
This completes the setup of the DR-X10C. Before you start using the scanner, make
sure to thoroughly read the Reference Guide or the User Manual.
● For details on how to use CapturePerfect 3.0, refer to CapturePerfect 3.0 Operation
Guide located in the Windows program menu.
●