Jura Impressa XS95 Instructions for use

The IMPRESSA XS95/XS90 One Touch Manual
KE
Original instructions for use
Before using the machine read the instructions for use.
The ‘IMPRESSA Manual’ has been awarded the seal of approval by the
independent German Technical Inspection Agency, TÜV SÜD, due to its
easy-to-understand style, its thoroughness and coverage of safety
aspects.
Downloaded from CoffeeMachineManual.com Manuals
JURA Type 668
Table of contents
Your IMPRESSA XS95/XS90 One Touch
Control elements
4
6
Proper use
For your safety
6
The IMPRESSA XS95/XS90 One Touch Manual
8
Symbol description ....................................................................................................................................... 8
1 Preparing and using for the first time
9
©
Connector System ..................................................................................................................................... 9
JURA on the Internet ..................................................................................................................................... 9
Setting up ....................................................................................................................................................... 9
Filling the water tank .................................................................................................................................... 9
Bean container filling...................................................................................................................................10
First-time use ................................................................................................................................................10
Using and activating filter ...........................................................................................................................11
Determining and adjusting the degree of water hardness ..................................................................12
Adjusting grinder ......................................................................................................................................... 13
Switching on .................................................................................................................................................14
Switching off .................................................................................................................................................15
2 Familiarising yourself with the control options
16
Preparation at the touch of a button........................................................................................................16
One-off settings before and during preparation ....................................................................................17
Entering a permanent setting for the amount of water for a cup size...............................................18
Permanent settings in programming mode ...........................................................................................19
Viewing information and maintenance status .......................................................................................21
Counter ......................................................................................................................................................... 22
3 Preparation at the touch of a button
23
Espresso ........................................................................................................................................................ 23
Coffee ............................................................................................................................................................ 23
Coffee à la Carte ..........................................................................................................................................24
Latte macchiato, cappuccino ....................................................................................................................24
Pre-ground coffee .......................................................................................................................................25
Hot milk and milk foam .............................................................................................................................26
Hot water ..................................................................................................................................................... 27
4 Permanent settings in programming mode
28
Products ........................................................................................................................................................28
Energy-saving mode (Energy Save Mode, E.S.M.©) ..............................................................................30
Automatic switch-off ...................................................................................................................................31
Downloaded from CoffeeMachineManual.com Manuals
2
Table of contents
Rinses .............................................................................................................................................................31
Restore factory settings ............................................................................................................................. 32
Lock................................................................................................................................................................ 33
Unit amount of water .................................................................................................................................34
Language ......................................................................................................................................................34
5 Maintenance
36
Maintenance tips .........................................................................................................................................36
Cleaning
the
cappuccino frother ......................................................................................................................................36
Rinsing the machine ................................................................................................................................... 37
Rinsing the cappuccino frother ................................................................................................................38
Disassembling and rinsing the Professional Cappuccino Frother ......................................................39
Disassembling and rinsing the Easy Cappuccino Frother....................................................................40
Cleaning the machine ................................................................................................................................40
Descaling the machine...............................................................................................................................42
Changing the filter ......................................................................................................................................44
Cleaning
the
bean container .............................................................................................................................................46
Descaling the water tank ........................................................................................................................... 47
6 Display messages
48
7 Troubleshooting
50
8 Transport and environmentally neutral disposal
52
Transport / Emptying the system.............................................................................................................52
Disposal.........................................................................................................................................................52
9 Technical data
53
Index
54
JURA contact details / Legal information
56
Downloaded from CoffeeMachineManual.com Manuals
3
Control elements
Control elements
8
1
9
2
10
11
3
12
13
4
14
15
5
6
7
Figure: IMPRESSA XS95 One Touch
1
2
3
4
5
6
7
Bean container cover
Bean container with aroma preservation
cover
Water tank with handle
Power switch and power cable
(back of machine)
Coffee grounds container
Cup platform
Drip tray
8
9
10
11
12
13
14
15
Fineness of grind switch
Cup tray
Cover of filler funnel for pre-ground coffee
Filler funnel for pre-ground coffee
Connector System©
for removable frothers
Professional Cappuccino Frother
Height-adjustable coffee spout
Hot water spout
Downloaded from CoffeeMachineManual.com Manuals
4
Control elements
4
1
5
2
3
Front left
1
Display
2
Rotary Switch cover
3
f Rotary switch
Q On/off button
c Maintenance button
i 1 Espresso button
4 2 Espressi button
o 1 Coffee button
d 2 Coffees button
e Coffee à la Carte button
v Pre-ground coffee button
Front right
4
ö Selector switch
5
Professional Cappuccino Frother
6 Easy Cappuccino Frother
a Hot water portion symbol
m Hot water symbol
p Cappuccino button
z Milk portion symbol
n Milk symbol
q Latte Macchiato button
The Connector System© permits the use of different frothers. These are available from stockists.
5
6
Downloaded from CoffeeMachineManual.com Manuals
5
Important information
Proper use
The machine is designed and intended for commercial use. It should
only be used for coffee preparation and to heat milk and water. Use
for any other purpose will be deemed improper. JURA Elektroapparate AG cannot accept any responsibility for the consequences of
improper use.
Before using the machine always carefully read and comply with all
these instructions. Keep this manual close to the IMPRESSA and, if
appropriate, pass it on to the next user.
For your safety
Please read and note carefully the following important safety information.
By doing this, you can avoid the life-threatening danger of electric
shock:
Z Never use a machine which has been damaged or with a
defective power cable.
Z For information on what to do in case of damage, for example
if there is a smell of burning, unplug the machine immediately
from the mains supply and contact the JURA service centre.
Z If the power cable for this machine is damaged, it must be
repaired either directly by JURA or by a JURA approved service
centre.
Z Make sure that the IMPRESSA and the power cable are not
located close to hot surfaces.
Z Be careful to ensure that the power cable does not get caught
and does not rub against sharp edges.
Z Never open and repair the machine yourself. Do not modify
the machine in any way that is not described in the IMPRESSA
Manual. The machine contains live parts. If opened, there is a
danger of serious injury. Repairs may only be carried out by
JURA approved service centres, using original spare parts and
accessories.
There is a risk of scalds or burns on the spouts or in the nozzle:
Z Place the machine out of the reach of children.
Z Do not touch any hot parts. Use the handles provided.
Downloaded from CoffeeMachineManual.com Manuals
6
Important information
Z
Be careful to ensure that the appropriate nozzle is installed
and clean. The nozzle or parts of the nozzle might come off if
the parts are not assembled correctly or a blockage occurs.
A defective machine is not safe and could cause injury or fire. To
avoid damage and any associated risk of injury or fire:
Z Never allow the power cable to loosely hang down. The power
cable can be tripped over or damaged.
Z Protect your IMPRESSA from environmental influences such
as rain, frost and direct sunlight.
Z Do not put the IMPRESSA, cable or connections in water.
Z Do not put the IMPRESSA or any individual parts in the dishwasher.
Z Turn your IMPRESSA off at the power switch before starting
any cleaning operation. Always wipe your IMPRESSA with a
damp cloth rather than a wet one, and protect it from prolonged water splash.
Z Do not set up the IMPRESSA anywhere where a jet of water
may be used.
Z Only connect the machine to a power supply in accordance
with the information on the rating plate. The rating plate is
located on the underside of your IMPRESSA. Further technical
data is given in Chapter 9 ‘Technical Data’.
Z Use only original JURA care products. Use of accessories that
are not explicitly recommended by JURA could damage the
IMPRESSA.
Z Do not use any coffee beans treated with additives or caramelised coffee beans.
Z Always fill the water tank with cold, fresh mains water.
Z If you will be absent for an extended period, turn the machine
off and unplug.
Safe handling of the CLARIS filter cartridges:
Z CLARIS filter cartridges should be kept out of the reach of children.
Z Store them dry in the sealed package.
Z Protect them from heat and direct sunlight.
Z Do NOT use damaged CLARIS filter cartridges.
Z Do NOT open CLARIS filter cartridges.
Downloaded from CoffeeMachineManual.com Manuals
7
The IMPRESSA XS95/XS90 One Touch Manual
The IMPRESSA XS95/XS90 One Touch Manual
You are holding the manual for your IMPRESSA XS95/XS90 One
Touch in your hand. It will help you to familiarize yourself with your
IMPRESSA safely and quickly and teach you the full range of facilities
it offers.
Chapter 1, ‘Preparing and using your IMPRESSA for the first time’,
explains step-by-step how to set up and prepare the IMPRESSA.
Chapter 2, ‘Familiarising yourself with the control options’ is important for you to read as you are familiarising yourself with your
IMPRESSA. It invites you to actively explore all the different coffee
experiences that it offers.
All the other chapters are intended to help you when you have a
specific query.
If you use the IMPRESSA XS95/XS90 One Touch Manual, you will become a master at preparing exciting coffee specialities, you will be a
Barista!
You can download the short operating instructions for your machine
from the JURA website (www.jura.com).
Symbol description
Warnings
Always take note of any information marked with the CAUTION or WARNING symbol.
The signal word WARNING points out potential risk of serious injury, and the signal
CAUTION word CAUTION potential risk of slight injury.
CAUTION
The CAUTION symbol is used to draw attention to circumstances which could cause
the machine to become damaged.
Symbols used
E
Information and tips to make things easier for you as you use your IMPRESSA.
@
References to the online JURA website, where you can find interesting further information: www.jura.com.
T
Prompt to take action. This symbol means that you are being prompted to perform
some action.
Downloaded from CoffeeMachineManual.com Manuals
8
1 Preparing and using for the first time
1
Preparing and using for the first time
This chapter provides you with the information you need to use your
IMPRESSA without any problems. You will prepare your IMPRESSA
step-by-step for your first coffee experience.
Connector System©
The Connector System© permits the use of different cappuccino
frothers:
Z Professional Cappuccino Frother
U Cappuccino / latte macchiato
U Hot milk
Z Easy Cappuccino Frother
U Cappuccino / latte macchiato
JURA on the Internet
Visit us on the Internet.
@ At www.jura.com you will find interesting and up-to-date
information on your IMPRESSA and on every aspect of coffee.
@ The Knowledge Builder awaits you at www.jura.com. The
interactive assistant, LEO, will support you and explain the
benefits of and how to use your IMPRESSA.
Setting up
When setting up your IMPRESSA, please note the following:
Z Set the IMPRESSA down on a horizontal surface that is not
sensitive to water.
Z Choose a spot for your IMPRESSA which is protected against
overheating. Ensure that the ventilation slots are not covered.
Filling the water tank
To enjoy perfect coffee we recommend changing the water every
day.
CAUTION
Milk, mineral water or other liquids can damage the water tank or
the machine.
T Only fill the water tank with fresh, cold water.
T Remove the water tank and rinse it with cold water.
T Fill the water tank with fresh, cold water and reinsert.
Downloaded from CoffeeMachineManual.com Manuals
9
1 Preparing and using for the first time
Bean container filling
CAUTION
The bean container has an aroma preservation cover. This will ensure
that your coffee beans retain their aroma for longer.
Coffee beans which have been treated with additives (e.g. sugar),
pre-ground or freeze-dried coffee will damage the grinder.
T Only use untreated coffee beans to refill the bean container.
T Open the cover of the bean container and remove the aroma
preservation cover.
T Remove any dirt or foreign objects inside the bean container.
T Fill the bean container with coffee beans, then close the
aroma preservation cover and the bean container cover.
First-time use
WARNING
If the machine is operated with a defective power cable, there is a
danger of electric shock.
T Never use a machine which has a defective power cable.
Precondition: The water tank and bean container are full.
T Insert the mains plug into a power socket.
3 T Switch on the IMPRESSA using the power switch on the back
of the machine.
The on/off button Q lights up (standby).
Q T Press the on/off button to switch the IMPRESSA on.
The pre-set language appears on the display.
T Open the cover of the Rotary Switch.
g T Turn the Rotary Switch until the desired language is displayed. For Example: LANGUAGE ENGLISH
k T Press the Rotary Switch to confirm the language.
CONFIRMED √ appears briefly on the display to confirm
the setting.
FILL SYSTEM / PRESS RINSE, the maintenance
button c lights up.
Downloaded from CoffeeMachineManual.com Manuals
10
1 Preparing and using for the first time
T Place a receptacle under the hot water spout and another
under the frother.
c T Press the maintenance button.
SYSTEM FILLS, the system fills up with water and the
maintenance button flashes. A small amount of water flows
from the frother and the hot water spout.
This operation stops automatically. WELCOME TO JURA
appears on the display.
HEATING UP
PRESS RINSE, the maintenance button c lights up.
T Place a receptacle under the coffee spout.
c T Press the maintenance button.
The machine rinses itself, stopping automatically.
COFFEE READY appears on the display. Your IMPRESSA
is ready to use.
E If you have not been able to use the machine for the first time
correctly and fully, contact customer support in your country
(see ‘JURA contact details / Legal information’).
Using and activating
filter
Your IMPRESSA no longer has to be descaled if you are using CLARIS
filter cartridges.
@ You can also try out the ‘Insert filter’ operation online. Visit the
Knowledge Builder at www.jura.com.
E Perform the ‘Insert filter’ operation without interruptions. This
will ensure that your IMPRESSA always produces its best.
Precondition: COFFEE READY is displayed.
T Open the cover of the Rotary Switch.
k T Keep the Rotary Switch pressed until MAINTENANCE
appears on the display.
g T Turn the Rotary Switch until FILTER NO is displayed.
k T Press the Rotary Switch to enter the programme item.
FILTER NO
g T Turn the Rotary Switch until FILTER YES is displayed.
k T Press the Rotary Switch to confirm the setting.
CONFIRMED w appears briefly on the display to confirm
the setting.
Downloaded from CoffeeMachineManual.com Manuals
11
1 Preparing and using for the first time
INSERT FILTER / PRESS RINSE, the maintenance
button c lights up.
T Remove a CLARIS filter cartridge and the filter cartridge extension from the Welcome Pack.
T Fit the extension on top of the filter cartridge.
T Remove the water tank and empty it.
T Lift the cartridge holder and insert the filter cartridge into
the water tank, applying slight pressure.
T Close the cartridge holder. It will click into place audibly.
T Fill the water tank with fresh, cold water and reinsert.
T Place a receptacle (at least 500 ml) under the frother.
E If you are using the Professional Cappuccino Frother, set the
selection lever of the frother to the steam position n.
c T Press the maintenance button.
FILTER RINSING, water flows out of the frother.
E You can interrupt rinsing of the filter at any time by pressing
any button.
E The water may be slightly discoloured. This is not harmful to
health and does not affect the taste.
Filter rinsing stops automatically after approx. 500 ml.
COFFEE READY appears on the display. The filter is now
activated.
Determining and
adjusting the degree of
water hardness
The harder the water is, the more frequently the IMPRESSA needs to
be descaled. It is therefore important to adjust the water hardness.
The water hardness can be adjusted on a continuous scale between
1° dH and 30° dH. This can also be deactivated, which means that
the IMPRESSA will not let you know when it has to be descaled.
E However, if you are using the CLARIS filter cartridge and have
activated it, you will not be able to adjust the water
hardness.
Downloaded from CoffeeMachineManual.com Manuals
12
1 Preparing and using for the first time
You can find out what the water hardness is by using the Aquadur®
test strip supplied as standard.
T Hold the test strip briefly (for one second) under flowing
water. Shake off the water.
T Wait for about one minute.
T You will then be able to read the degree of water hardness
from the discolouration of the Aquadur® test strip and the
description on the packaging.
You can now adjust the water hardness.
Example: To change the water hardness from 16°dH to 25°dH,
proceed as follows:
Precondition: COFFEE READY is displayed.
T Open the cover of the Rotary Switch.
k T Keep the Rotary Switch pressed until MAINTENANCE
appears.
g T Turn the rotary switch until HARDNESS 16°dH is
displayed.
k T Press the Rotary Switch to enter the programme item.
16°dH
g T Turn the Rotary Switch until 25°dH is displayed.
k T Press the Rotary Switch to confirm the setting.
CONFIRMED w appears briefly on the display.
HARDNESS 25°dH
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
COFFEE READY is shown on the display.
Adjusting grinder
CAUTION
You can adjust the grinder continuously to suit the roast of your
coffee.
If you adjust the fineness of grind when the grinder is not operating,
the grinding wheel could be damaged.
T Only adjust the fineness of grind when the grinder is running.
The fineness of grind setting is correct if the coffee flows regularly
from the coffee spout. A fine, thick crema is also formed.
Downloaded from CoffeeMachineManual.com Manuals
13
1 Preparing and using for the first time
Our recommendations:
Z Select a fine setting for a light roast.
U If the fineness of grind setting is too fine, the coffee only
drips from the coffee spout.
Z
Select a coarse setting for a darker roast.
U If the fineness of grind is too coarse the coffee flows too
quickly from the coffee spout.
Example: To change the fineness of grind during coffee preparation,
proceed as follows:
T Open the cover of the bean container.
T Place a cup under the coffee spout.
o T Press the 1 Coffee button.
The grinder starts and 1 COFFEE is displayed.
T Turn the fineness of grind switch to the desired position
while the grinder is running.
The coffee will be prepared and the fineness of grind is
adjusted.
Switching on
When the IMPRESSA is switched on, a prompt for the rinse operation
automatically appears which is initiated by pressing the maintenance button.
This setting can be changed in programming mode so that the
machine automatically activates the switch-on rinse (see Chapter 4
‘Permanent settings in programming mode – Rinses’).
Precondition: Your IMPRESSA is switched on at the power switch
and the on/off button Q is illuminated.
Q T Press the on/off button to switch the IMPRESSA on.
WELCOME TO JURA appears briefly on the display.
HEATING UP
PRESS RINSE, the maintenance button c lights up.
Downloaded from CoffeeMachineManual.com Manuals
14
1 Preparing and using for the first time
T Place a receptacle under the coffee spout.
c T Press the maintenance button.
The machine rinses itself, stopping automatically.
COFFEE READY appears on the display. Your IMPRESSA
is ready to use.
Switching off
When you switch your IMPRESSA off, the spouts with which a coffee
speciality or milk have been prepared are rinsed.
T Place a receptacle under the coffee spout and the frother.
Q T Press the on/off button.
MACHINE RINSING appears on the display, and the
coffee spout is rinsed.
SPOUT RIGHT / PRESS RINSE.
c T Press the maintenance button.
MACHINE RINSING, the right coffee spout is rinsed.
The IMPRESSA is switched off, and the on/off button Q lights
up.
E When your IMPRESSA is switched off, a hissing noise may be
audible. This is normal and does not have any effect on the
machine.
Downloaded from CoffeeMachineManual.com Manuals
15
2 Familiarising yourself with the control options
2 Familiarising yourself with the control options
With the IMPRESSA, you can prepare an excellent coffee or milk speciality at the touch of a button. You also have the option of adjusting
the coffee strength and temperature, as well as the amount of water
to your personal taste.
This chapter will allow you to become familiar with all control
options with the aid of examples. To familiarise yourself with your
IMPRESSA, we recommend that you make a point of actively trying
the facilities described in this chapter. You will find this is well worthwhile.
Learn how to perform the following:
Z Preparation at the touch of a button
Z One-off settings before and while your drink is being prepared
Z Adjusting the default amount of water to suit the cup size
Z Permanent settings in programming mode
E You can stop the machine at any time while a coffee or milk
speciality or hot water is being prepared. To do this, press any
button.
@ If you prefer to familiarise yourself with your IMPRESSA in a
fun way on the computer, the interactive Knowledge Builder
tutorial programme can be found on the Internet at
www.jura.com.
Preparation at the
touch of a button
Prepare your favourite coffee speciality at the touch of a button.
All coffee specialities are prepared following this model.
Example: This is how to prepare one coffee.
Precondition: COFFEE READY is displayed.
T Place a cup under the coffee spout.
o T Press the 1 Coffee button.
1 COFFEE and the pre-set coffee strength is displayed.
The pre-set amount of water flows into the cup. Preparation
stops automatically. ENJOY appears on the display.
COFFEE READY is then displayed.
E To prepare 2 coffees, place two cups under the coffee spout
and press the
2 Coffees button d.
Downloaded from CoffeeMachineManual.com
Manuals
16
2 Familiarising yourself with the control options
One-off settings before
and during preparation
It is possible to make various settings before and during preparation.
These one-off settings are always follow the same model and are not
stored.
Changing the coffee
strength before preparation
The coffee strength of Coffee à la Carte can be changed before
preparation. The following coffee strength options can be selected:
Z ö (xmild)
Z öö (mild)
Z ööö (normal)
Z öööö (strong)
Z ööööö (xstrong)
Example: Proceed as follows to to prepare a strong cup of Coffee à
la Carte.
Precondition: COFFEE READY is displayed.
T Place a cup under the coffee spout.
T Open the cover of the Rotary Switch.
e T Press the Coffee à la Carte button.
A LA CARTE and the pre-set coffee strength is displayed.
g T Turn the Rotary Switch until A LA CARTE öööö is
displayed.
k T Turn the Rotary Switch while A LA CARTE öööö is
displayed.
A LA CARTE öööö, the pre-set amount of water flows
into the cup. Preparation stops automatically. ENJOY
appears on the display. COFFEE READY is then displayed.
Changing the amount of
water during preparation
The pre-set amount of water of all coffee products can be changed
during the brewing operation by turning the Rotary Switch.
Example: Proceed as follows to prepare a 110 ML cup of coffee.
Precondition: COFFEE READY is displayed.
T Place a cup under the coffee spout.
Downloaded from CoffeeMachineManual.com Manuals
17
2 Familiarising yourself with the control options
T Open the cover of the Rotary Switch.
o T Press the 1 Coffee button.
1 COFFEE and the pre-set coffee strength is displayed.
The brewing operation starts and the coffee flows into the
cup.
g T Turn the Rotary Switch during the brewing operation until
1 COFFEE / 110 ML is displayed.
The set amount of water flows into the cup. Preparation
stops automatically. ENJOY appears on the display.
COFFEE READY is then displayed.
Entering a permanent
setting for the amount
of water for a cup size
It is easy to make permanent settings for the amount of water for all
coffee specialities, cappuccino, latte macchiato, a portion of hot
water and portion of milk according to the cup size. As in the following example, adjust the amount of water once. Every time you prepare a drink in the future, this amount of water will be dispensed.
Making the permanent settings for the amount of water for the
respective cup size always follows this model.
Example: To make permanent settings for the amount of water for
an espresso, proceed as follows:
Precondition: COFFEE READY is displayed.
T Place an espresso cup under the coffee spout.
i T Press and hold the 1 Espresso button.
1 ESPRESSO and the coffee strength is displayed.
i T Hold the Espresso button down until ENOUGH COFFEE?
appears.
i T Release the 1 Espresso button.
Coffee preparation will start and the espresso will flow into
the cup.
T Press any button as soon as enough espresso has flowed
into the cup.
Preparation stops automatically. CONFIRMED w appears
briefly on the display. The set amount of water for an espresso will be permanently stored. COFFEE READY is then
displayed.
E You can alter these settings at any time by repeating the
above procedure.
Downloaded from CoffeeMachineManual.com Manuals
18
2 Familiarising yourself with the control options
Permanent settings in
programming mode
You can easily adjust your IMPRESSA to your personal coffee blends
and specialities. You can navigate through the easy-to-understand
programme steps and make permanent settings simply by turning
and pressing the Rotary Switch.
You can make the following permanent settings with the Rotary
Switch:
Programme item
Subitem
Explanation
MAINTENANCE
CLEAN CAPPUCCINO,
RINSE MACHINE,
RINSE CAPPUCCINO,
CLEAN MACHINE,
DECALCIFY MACHINE,
CHANGE FILTER
T Select the desired maintenance
programme.
If no action is taken, programming mode
is exited in the MAINTENANCE programme item automatically after approx.
five seconds.
PRODUCTS
SELECT PRODUCT
T Select your settings for the coffee and
milk specialities and hot water.
FILTER
FILTER YES
FILTER NO
T Indicate whether you operate your
IMPRESSA with or without a CLARIS filter
cartridge.
HARDNESS
HARDNESS INACTIVE, T Adjust the water hardness.
1°dH – 30°dH
(is only displayed
when the filter is
not activated)
ECONOMY MODE
SAVE NO,
SAVE LEVEL 1,
SAVE LEVEL 2
T Select an energy-saving mode.
OFF AFTER
0.5 H – 15 H
T Set the number of hours after which the
IMPRESSA should switch off automatically.
RINSES
INIT RINSE,
CAPP RINSE
T Set whether the switch-on rinse should
be started manually or automatically.
T Set whether the prompt for cappuccino
rinsing should be started immediately
or 10 minutes afterpreparation of a milk
speciality.
Downloaded from CoffeeMachineManual.com Manuals
19
2 Familiarising yourself with the control options
Programme item
Subitem
Explanation
RESET
PRODUCT,
ALL PROD.,
ALL,
EMPT.SYST.
T Reset the permanently set values of all
products to the factory settings.
LOCK
PRODUCT,
PRE-SELECT,
MAINT.
T Lock the buttons for individual products,
pre-selection of coffee strength (for coffee à
la carte) or the maintenance programmes.
INFORMATION
T Keep track of all prepared coffee and milk
specialities and view the maintenance
status.
COUNTER
T You have the option of specifying your
consumption over a timeframe determined
by you. You can reset this counter to zero at
any time.
SETTINGS
ML/OZ
T Select the unit of the amount of water.
LANGUAGE
T Select the desired language.
EXIT
T Exit programming mode.
Settings in programming mode always follow the same model.
Example: To change the strength of one espresso from
öööö (strong) to ööö (normal).
Precondition: COFFEE READY is displayed.
T Open the cover of the Rotary Switch.
k T Keep the Rotary Switch pressed until MAINTENANCE
appears.
g T Turn the Rotary Switch until PRODUCTS is displayed.
k T Press the Rotary Switch to enter the programme item.
SELECT PRODUCT
E Next select the product button for which you would like to
make settings. No product is prepared during this procedure.
i T Press the 1 Espresso button.
WATER 45 ML
g T Turn the Rotary Switch until AROMA öööö is displayed.
Downloaded from CoffeeMachineManual.com Manuals
20
2 Familiarising yourself with the control options
k T Press the Rotary Switch to enter the programme item.
STRONG öööö
g T Turn the Rotary Switch until NORMAL ööö is displayed.
k T Press the Rotary Switch to confirm the setting.
CONFIRMED w appears briefly on the display.
AROMA ööö
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit the programme item.
SELECT PRODUCT
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit the programme item.
PRODUCTS
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
COFFEE READY
Viewing information
and maintenance
status
Under the programme item INFORMATION you can query the
following information:
Z Number of the prepared coffee and milk specialities and hot
water
Z Maintenance status and number of maintenance programmes
performed (cleaning, descaling, filter change, Cappuccino
frother cleaning)
Z Software version
Precondition: COFFEE READY is displayed.
T Open the cover of the Rotary Switch.
k T Press the Rotary Switch until MAINTENANCE appears.
g T Turn the Rotary Switch until INFORMATION is displayed.
k T Press the Rotary Switch to enter the programme item.
TOTAL, the sum of all prepared coffee and milk specialities
is displayed.
g T Turn the Rotary Switch for further information.
E The respective maintenance status can also be displayed in
addition to the number of performed maintenance programmes. The bar shows the current maintenance status.
When the bar is filled completely, your IMPRESSA will request
the respective maintenance programme.
Downloaded from CoffeeMachineManual.com Manuals
21
2 Familiarising yourself with the control options
k T Press the Rotary Switch to exit the programme item.
INFORMATION
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
COFFEE READY
Counter
In the COUNTER programme item, you have the option of specifying your consumption over a timeframe determined by you. You can
reset this counter to zero at any time.
Example: How to reset the counter to zero.
Precondition: COFFEE READY is displayed.
T Open the cover of the Rotary Switch.
k T Press and hold the Rotary Switch until MAINTENANCE
appears.
g T Turn the Rotary Switch until COUNTER is displayed.
k T Press the Rotary Switch to enter the programme item.
TOTAL, the total number of prepared speciality coffees
and milk specialities is displayed.
E You can query more information by turning the Rotary Switch.
k T Press the Rotary Switch.
DELETE NO
E If you do not want to reset the counter, press the Rotary
Switch.
g T Turn the Rotary Switch until DELETE YES is displayed.
k T Press the Rotary Switch to confirm the setting.
OK appears briefly on the display.
COUNTER
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
COFFEE READY
Downloaded from CoffeeMachineManual.com Manuals
22
3 Preparation at the touch of a button
3 Preparation at the touch of a button
In this chapter you will find out how to prepare coffee and milk specialities and hot water without making further settings.
Chapter 2, ‘Familiarising yourself with the control options’, will teach
you how to adjust the settings to your personal preferences. Alternatively, you can use Chapter 4, ‘Permanent settings in programming mode’.
E You can stop the machine at any time while a coffee or milk
product or hot water is being prepared. To do this, press any
button.
E During preparation, you can change the pre-set amount of
water by turning the Rotary Switch.
@ You can also try out the preparation of coffee specialities online. Visit the Knowledge Builder at www.jura.com.
Espresso
The classic coffee drink from Italy. There is a definite crema on the
surface of the espresso.
Example: This is how to prepare one espresso.
Precondition: COFFEE READY is displayed.
T Place an espresso cup under the coffee spout.
i T Press the 1 Espresso button.
1 ESPRESSO and the pre-set coffee strength are displayed.
The pre-set amount of water flows into the cup. Preparation
stops automatically. ENJOY appears on the display.
COFFEE READY is then displayed.
E To prepare two espressi place two cups under the coffee
spout and press the 2 Espressi button 4.
Coffee
Example: This is how to prepare one coffee.
Precondition: COFFEE READY is displayed.
Downloaded from CoffeeMachineManual.com Manuals
23
3 Preparation at the touch of a button
T Place a coffee cup under the coffee spout.
o T Press the 1 Coffee button.
1 COFFEE and the pre-set coffee strength are displayed.
The pre-set amount of water flows into the cup. Preparation
stops automatically. ENJOY appears on the display.
COFFEE READY is then displayed.
E To prepare 2 coffees, place two cups under the coffee spout
and press the 2 Coffees button d.
Coffee à la Carte
The coffee strength of Coffee à la Carte can be changed before
preparation.
Example: Proceed as follows to prepare a strong (öööö) cup of
Coffee à la Carte.
Precondition: COFFEE READY is displayed.
T Place a cup under the coffee spout.
T Open the cover of the Rotary Switch.
e T Press the Coffee à la Carte button.
A LA CARTE ö
g T Turn the Rotary Switch until A LA CARTE öööö is
displayed.
k T Press the Rotary Switch while A LA CARTE öööö is
displayed.
A LA CARTE öööö, the pre-set amount of water flows
into the cup. Preparation stops automatically. ENJOY appears on the display. COFFEE READY is then displayed.
Latte macchiato,
cappuccino
Your IMPRESSA can prepare a latte macchiato or cappuccino at the
touch of a button. There is no need to move the glass or cup.
Example: Proceed as follows to prepare one latte macchiato.
Precondition: COFFEE READY is displayed.
T Take the protective cover off the Cappuccino Frother.
T Attach the milk pipe to the frother. For a milk carton/bottle
use the long pipe, for a milk container the short pipe.
T Insert the other end into a milk carton/bottle or connect it to
the milk container.
Downloaded from CoffeeMachineManual.com Manuals
24
3 Preparation at the touch of a button
T Place a glass under the frother.
E If you are using the Professional Cappuccino Frother, set the
selector switch to the Milk Foam position p.
q T Press the Latte Macchiato button.
LATTE MAC. and the coffee strength are displayed.
The milk foam is then prepared. The operation stops automatically when pre-set amount of milk is reached.
E A brief pause follows during which the hot milk separates from
the milk foam. This enables the formation of the typical layers
of a latte macchiato. The duration of this pause can be defined
in programming mode.
Coffee preparation then begins. The pre-set amount of
water flows into the glass. Preparation stops automatically.
ENJOY appears on the display. COFFEE READY is then
displayed.
To ensure that the frother works perfectly, you should rinse and
clean it regularly. The description for this can be found in Chapter 5
‘Maintenance – Cappuccino frother’.
Pre-ground coffee
You can choose a second coffee blend, for example decaffeinated
coffee, with the filler funnel for pre-ground coffee.
E Never add more than two level measuring spoons of preground coffee.
E Use pre-ground coffee which is not ground too finely. Very
fine coffee can block up the system so that the coffee only
comes out in drips.
E If you did not fill the machine with a sufficient amount of preground coffee, NOT ENOUGH PRE-GROUND is displayed
and the IMPRESSA stops operation.
All coffee specialities with pre-ground coffee are prepared following
this model.
Example: This is how to prepare a cup of coffee using pre-ground
coffee.
T Place a cup under the coffee spout.
Downloaded from CoffeeMachineManual.com Manuals
25
3 Preparation at the touch of a button
T Open the cover of the filler funnel for pre-ground coffee.
T Open the cover of the Rotary Switch.
v T Press the Pre-ground coffee button.
FILL PRE-GROUND / COFFEE READY
T Place one level measuring spoon of pre-ground coffee into
the filler funnel.
T Close the cover of the filler funnel for pre-ground coffee.
o T Press the 1 Coffee button.
1 COFFEE, the pre-set amount of water flows into the cup.
Preparation stops automatically. ENJOY appears on the
display. COFFEE READY is then displayed.
Hot milk and milk
foam
E This chapter applies to the Professional and Easy Cappuccino
Frothers.
There are two options for preparing hot milk or milk foam:
Z Milk portion z
U The preset quantity of milk is then prepared.
Z Milk n
U Milk is prepared until preparation is interrupted by pressing
any button.
Example: Proceed as follows to prepare milk foam.
Precondition: COFFEE READY is displayed.
T Take the protective cover off the frother.
T Attach the milk pipe to the frother. For a milk carton/bottle
use the long pipe, for a milk container the short pipe.
T Insert the other end into a milk carton/bottle or connect it to
the milk container.
T Place a cup under the frother.
E If you are using the Professional Cappuccino Frother, turn
the selector switch to the Milk Foam position p.
E If you want to heat the milk, turn the selector switch of the
Professional Cappuccino Frother to the Milk position t.
ö T With the selector switch select the milk portion symbol z.
Downloaded from CoffeeMachineManual.com Manuals
26
3 Preparation at the touch of a button
ä T Press the selector switch.
MILK, the milk foam is being prepared. Preparation stops
automatically when the pre-set amount of milk is reached.
COFFEE READY is shown on the display.
To ensure that the frother works perfectly, you should rinse and
clean it regularly. The description for this can be found in Chapter 5
‘Maintenance – Cappuccino frother’.
Hot water
Hot water can be prepared in two ways:
Z Hot water portion a
U The pre-set amount of water flows into the cup.
Z Hot water m
U Water flows out of the hot water spout until preparation is
interrupted by pressing any button.
The following temperatures can be selected for preparing hot
water:
Z Low
Z Normal
Z X high
CAUTION
There is a danger of scalding from hot water splashes.
T Avoid direct contact with the skin.
Example: This is how to prepare a portion of hot water.
Precondition: COFFEE READY is displayed.
T Place a cup under the hot water spout.
ö T Use the selector switch to select the hot water portion
symbol a.
ä T Press the selector switch.
TEMPERATURE and the pre-set temperature are displayed.
E By pressing the selector switch several times (within approx.
2 seconds) you can set the temperature to your individual
preference. This setting is not saved.
HOT WATER, the pre-set amount of water flows into the
cup. Preparation stops automatically. COFFEE READY
appears on the display.
Downloaded from CoffeeMachineManual.com Manuals
27
4 Permanent settings in programming mode
4 Permanent settings in programming mode
Products
With the PRODUCTS programme item you can enter individual
settings for all coffee and milk specialities as well as hot water.
The following permanent settings can be made:
Product
Amount
Coffee strength
Temp.
1 Espresso,
1 Coffee
25 ML – 240 ML
ö (xmild),
öö (mild),
ööö (normal),
öööö (strong),
ööööö (xstrong)
NORMAL, HIGH
2 Espressi,
2 Coffees
25 ML – 240 ML
–
NORMAL, HIGH
Coffee à la Carte
25 ML – 240 ML
–
NORMAL, HIGH
Latte macchiato,
Cappuccino
Amount of milk:
3 SEC – 120 SEC
Pause:
0 SEC – 60 SEC
Amount of water:
25 ML – 240 ML
ö (xmild),
öö (mild),
ööö (normal),
öööö (strong),
ööööö (xstrong)
NORMAL, HIGH
Milk portion
3 SEC – 120 SEC
–
–
–
–
Hot water portion 25 ML – 450 ML
–
LOW, NORMAL, X HIGH
Hot water
–
LOW, NORMAL, X HIGH
Milk
(per cup)
–
–
Permanent settings in programming mode always follow the same
model.
Example: Proceed as follows to change the amount of milk of latte
macchiato from 16 SEC to 20 SEC, the pause from 30 SEC
to 40 SEC and the amount of water from 45 ML to 40 ML.
Precondition: COFFEE READY is displayed.
T Open the cover of the Rotary Switch.
k T Keep the Rotary Switch pressed until MAINTENANCE
appears.
g T Turn the Rotary Switch until PRODUCTS is displayed.
Downloaded from CoffeeMachineManual.com Manuals
28
4 Permanent settings in programming mode
k T Press the Rotary Switch to enter the programme item.
SELECT PRODUCT
E Next select the product button for which you would like to
make settings. No product is prepared during this procedure.
q T Press the Latte Macchiato button.
COFFEE 45 ML
k T Press the Rotary Switch to enter the programme item.
COFFEE 45 ML
g T Turn the Rotary Switch until COFFEE 40 ML is displayed.
k T Press the Rotary Switch to confirm the setting.
CONFIRMED w appears briefly on the display.
COFFEE 40 ML
g T Turn the Rotary Switch until MILK 16 SEC is displayed.
k T Press the Rotary Switch to enter the programme item.
MILK 16 SEC
g T Turn the Rotary Switch until MILK 20 SEC is displayed.
k T Press the Rotary Switch to confirm the setting.
CONFIRMED w appears briefly on the display.
MILK 20 SEC
g T Turn the Rotary Switch until PAUSE 30 SEC is displayed.
k T Press the Rotary Switch to enter the programme item.
PAUSE 30 SEC
g T Turn the Rotary Switch until PAUSE 40 SEC is displayed.
k T Press the Rotary Switch to confirm the setting.
CONFIRMED w appears briefly on the display.
PAUSE 40 SEC
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit the programme item.
SELECT PRODUCT
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit the programme item.
PRODUCTS
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
COFFEE READY
Downloaded from CoffeeMachineManual.com Manuals
29
4 Permanent settings in programming mode
Energy-saving mode
(Energy Save Mode,
E.S.M.©)
You can also set various energy-saving modes on your IMPRESSA:
Z SAVE NO
U Your IMPRESSA is continuously ready for use.
U All coffee and milk products, as well as hot water, can be
prepared without having to wait.
Z SAVE LEVEL 1
U Your IMPRESSA is only continuously ready for use for coffee
products and hot water.
U The machine has to heat up before milk preparation.
Z SAVE LEVEL 2
U Approx. 5 minutes after the last preparation the IMPRESSA
switches to the energy-saving temperature and is not ready
for use.
U Before coffee, hot water or milk can be prepared, the machine
has to heat up.
Example: Proceed as follows to change the energy-saving mode
from SAVE LEVEL 1 to SAVE LEVEL 2.
Precondition: COFFEE READY is displayed.
T Open the cover of the Rotary Switch.
k T Keep the Rotary Switch pressed until MAINTENANCE
appears.
g T Turn the Rotary Switch until ECONOMY MODE 1 is
displayed.
k T Press the Rotary Switch to enter the programme item.
SAVE LEVEL 1
g T Turn the Rotary Switch until SAVE LEVEL 2 is displayed.
k T Press the Rotary Switch to confirm the setting.
CONFIRMED w appears briefly on the display.
ECONOMY MODE 2
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
COFFEE READY
Downloaded from CoffeeMachineManual.com Manuals
30
4 Permanent settings in programming mode
Automatic switch-off
By instructing your IMPRESSA to automatically switch itself off, you
can cut down your energy consumption. If this function is activated,
your IMPRESSA switches off automatically after the last action on
the machine.
E The programmable switch-off time can be adjusted between
0.5 and 15 hours.
Example: Proceed as follows to change the automatic switch-off
time from 2 H to 1 H.
Precondition: COFFEE READY is displayed.
T Open the cover of the Rotary Switch.
k T Keep the Rotary Switch pressed until MAINTENANCE
appears.
g T Turn the Rotary Switch until OFF AFTER 2 H is displayed.
k T Press the Rotary Switch to enter the programme item.
OFF AFTER 2 H
g T Turn the Rotary Switch until OFF AFTER 1 H is displayed.
k T Press the Rotary Switch to confirm the setting.
CONFIRMED w appears briefly on the display.
OFF AFTER 1 H
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
COFFEE READY
Rinses
You can set whether the switch-on rinse should be started manually or automatically.
You can set whether cappuccino rinsing should be prompted immediately or 10 minutes after a milk product has been prepared.
Example: Proceed as follows to programme that Cappuccino rinsing
should be prompted immediately after a milk product has been
prepared.
Precondition: COFFEE READY is displayed.
T Open the cover of the Rotary Switch.
k T Keep the Rotary Switch pressed until MAINTENANCE
appears.
g T Turn the Rotary Switch until RINSES is displayed.
k T Press the Rotary Switch to enter the programme item.
INIT RINSE MANUAL
Downloaded from CoffeeMachineManual.com Manuals
31
4 Permanent settings in programming mode
g T Turn the Rotary Switch until CAPP RINSE AFTER 10’
is displayed.
k T Press the Rotary Switch to enter the programme item.
CAPP RINSE AFTER 10’
g T Turn the Rotary Switch until CAPP RINSE NOW is
displayed.
k T Press the Rotary Switch to confirm the setting.
CONFIRMED w appears briefly on the display.
CAPP RINSE NOW
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit the programme item.
RINSES
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
COFFEE READY
Restore factory settings
In the programme item RESET you can reset various settings to
their factory settings:
Z PRODUCT
U The settings (amount of water, aroma, temperature etc.) for
any product can be reset individually to the factory settings.
The corresponding double product is reset to the factory
settings at the same time.
Z ALL PROD.
U The settings (amount of water, aroma, temperature etc.) for
all products are reset to the factory settings.
Z ALL
U All customer settings are reset to the factory settings. Your
IMPRESSA then switches off.
Z EMPT.SYST.
U The system will be emptied. Your IMPRESSA then switches
off.
Example: Proceed as follows to reset the values for ‘Espresso’ to the
factory settings.
Precondition: COFFEE READY is displayed.
k T Keep the Rotary Switch pressed until MAINTENANCE
appears.
g T Turn the Rotary Switch until RESET is displayed.
Downloaded from CoffeeMachineManual.com Manuals
32
4 Permanent settings in programming mode
k T Press the Rotary Switch to enter the programme item.
RESET / PRODUCT
k T Press the Rotary Switch to enter the programme item.
SELECT PRODUCT
i T Press the Espresso button.
CONFIRMED w appears briefly on the display. The settings for ‘Espresso’ are reset to the factory settings.
RESET / PRODUCT
g T Turn the Rotary Switch until RESET / EXIT is displayed.
k T Press the Rotary Switch to exit the programme item.
RESET
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
COFFEE READY
Lock
Settings in LOCK programme item:
Z PRODUCT
U Each product can be locked individually, preparation is not
possible. If the button is subsequently pressed, LOCKED
appears briefly in the display.
Z PRE-SELECT
U The pre-selection of coffee strength for coffee à la carte is
locked.
Z MAINT.
U All maintenance programmes are locked and cannot be
started. The MAINTENANCE programme item is locked.
Example: How to lock the 2 Espressi button.
Precondition: COFFEE READY is displayed.
k T Press and hold the Rotary Switch until MAINTENANCE
appears.
g T Turn the Rotary Switch until LOCK is displayed.
k T Press the Rotary Switch to enter the programme item.
LOCK / PRODUCT
E Turn the Rotary Switch to select the PRE-SELECT and
MAINT. programme items.
k T Press the Rotary Switch.
SELECT PRODUCT
Downloaded from CoffeeMachineManual.com Manuals
33
4 Permanent settings in programming mode
4 T Press the 2 Espressi button.
LOCKED appears briefly on the display.
LOCK / PRODUCT
E To unlock, press the Rotary Switch and then the corresponding product button. FREE appears briefly on the display.
g T Turn the Rotary Switch until LOCK / EXIT is displayed.
k T Press the Rotary Switch to exit the programme item.
LOCK
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
COFFEE READY
Unit amount of water
You can change the unit of the amount of water from ‘ml’ to ‘oz’.
Example: To change the unit for the amount of water from ML to
OZ, proceed as follows.
Precondition: COFFEE READY is displayed.
T Open the cover of the Rotary Switch.
k T Keep the Rotary Switch pressed until MAINTENANCE
appears.
g T Turn the Rotary Switch until SETTINGS ML is displayed.
k T Press the Rotary Switch to enter the programme item.
SETTINGS ML
g T Turn the Rotary Switch until SETTINGS OZ is displayed.
k T Press the Rotary Switch to confirm the setting.
CONFIRMED w appears briefly on the display.
SETTINGS OZ
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
COFFEE READY
Language
You set the language when you used the machine for the first
time.
Example: To change the language from ENGLISH to DEUTSCH
(example), proceed as follows.
Precondition: COFFEE READY is displayed.
k T Keep the Rotary Switch pressed until MAINTENANCE
appears.
Downloaded from CoffeeMachineManual.com Manuals
34
4 Permanent settings in programming mode
g T Turn the Rotary Switch until LANGUAGE ENGLISH is
displayed.
k T Press the Rotary Switch to enter the programme item.
LANGUAGE ENGLISH
g T Turn the Rotary Switch until SPRACHE DEUTSCH
(example) is displayed.
k T Press the Rotary Switch to confirm the setting.
GESPEICHERT w (example) appears briefly on the display.
SPRACHE DEUTSCH (example)
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
BITTE WÄHLEN (example)
Downloaded from CoffeeMachineManual.com Manuals
35
5 Maintenance
5 Maintenance
Your IMPRESSA has the following integrated maintenance programmes:
Z Clean cappuccino frother
Z Rinse machine
Z Rinse cappuccino frother
Z Clean machine
Z Decalcify machine
Z Change filter
E Clean or descale the machine or change the filter whenever
the appropriate prompt is displayed.
Maintenance tips
To ensure that you get many years of reliable service out of your
IMPRESSA and to guarantee the optimum coffee quality, the
machine requires daily maintenance.
You should proceed as follows:
Z Empty the coffee grounds container and the drip tray. Rinse
them with warm water.
Z Rinse the water tank with clean water.
Z Dismantle and rinse the frother (see Chapter 5
‘Maintenance – Rinsing the cappuccino frother’).
Z Wipe the surface of the machine with a damp cloth.
Cleaning the
cappuccino frother
E This chapter applies to the Professional and Easy Cappuccino
Frothers.
To ensure that the respective frother works perfectly, you should
clean it daily when you have been preparing milk.
CAUTION
If the wrong cleaning agent is used, the machine could be damaged
and/or traces of detergent could be left behind in the water.
T Use only original JURA care products.
E The IMPRESSA will not prompt you to clean the frother.
E The JURA Cappuccino Cleaner is available from stockists.
@ You can also try out the ‘Cleaning the cappuccino frother’
operation online. Visit the Knowledge Builder at
www.jura.com.
Downloaded from CoffeeMachineManual.com
Manuals
36
5 Maintenance
Precondition: COFFEE READY is displayed.
T Open the cover of the Rotary Switch.
k T Keep the Rotary Switch pressed until MAINTENANCE
appears.
k T Press the Rotary Switch to enter the programme item.
CLEAN CAPPUCCINO
k T Press the Rotary Switch.
CLEANER FOR CAPPU., the maintenance button c
lights up.
T Pour 250 ml of fresh water into a container and add one
capful (max. 15 ml) of Cappuccino Cleaner.
T Immerse the milk pipe in the receptacle with the cleaning
solution.
E If you are using the Professional Cappuccino Frother, turn
the selection lever to the milk foam p or milk t position.
T Place another receptacle under the frother.
c T Press the maintenance button.
CAPPUCCINO / CLEANS, the frother and pipe are
cleaned.
WATER FOR CAPPUCCINO, the maintenance button c
lights up.
T Rinse the receptacle thoroughly, fill it with approx. 250 ml
of fresh water and immerse the milk pipe in the water.
T Empty the other receptacle and place it under the frother
once more.
c T Press the maintenance button.
CAPPUCCINO / CLEANS, the frother and pipe are
rinsed with fresh water.
COFFEE READY appears on the display. Your IMPRESSA
is once more ready to use.
Rinsing the machine
When the IMPRESSA is switched on, a prompt to perform a rinse
operation appears after heating, or this is automatically started.
It can be set in programming mode whether the switch-on rinse
needs to be activated manually or whether the machine automatically activates the switch-on rinse (see Chapter 4 ‘Permanent settings in programming mode – Rinses’).
Downloaded from CoffeeMachineManual.com Manuals
37
5 Maintenance
When the IMPRESSA is switched off, a rinse operation is automatically initiated.
You can initiate the rinse operation manually at any time.
Precondition: COFFEE READY is displayed.
T Place a receptacle under the coffee spout.
T Open the cover of the Rotary Switch.
k T Keep the Rotary Switch pressed until MAINTENANCE
appears.
k T Press the Rotary Switch to enter the programme item.
CLEAN CAPPUCCINO
f T Turn the Rotary Switch until RINSE MACHINE is displayed.
k T Press the Rotary Switch to initiate the rinse operation.
MACHINE RINSING
Rinsing stops automatically and your IMPRESSA is then once
more ready for use.
Rinsing the cappuccino
frother
E This chapter applies to the Professional and Easy Cappuccino
Frothers.
Each time milk has been prepared the IMPRESSA displays a prompt
for Cappuccino rinsing.
It can be set in programming mode whether the rinsing prompt is
displayed immediately or 10 minutes after preparation (refer to
Chapter 4 ‘Permanent settings in programming mode – Rinses’).
Rinsing following a prompt
Precondition: COFFEE READY / RINSE CAPPUCCINO is
displayed and the maintenance button c lights up.
T Place a receptacle under the frother.
E If you are using the Professional Cappuccino Frother, turn
the selection lever to the steam position n.
c T Press the maintenance button.
CAPPU. RINSING, the frother is rinsed.
The procedure stops automatically. COFFEE READY
appears on the display.
Downloaded from CoffeeMachineManual.com Manuals
38
5 Maintenance
Starting rinsing manually
You can initiate the ‘Rinsing the cappuccino frother’ operation
manually.
Precondition: COFFEE READY is displayed.
T Place a receptacle under the frother.
E If you are using the Professional Cappuccino Frother, turn
the selection lever to the steam position n.
T Open the cover of the Rotary Switch.
k T Keep the Rotary Switch pressed until MAINTENANCE
appears.
k T Press the Rotary Switch to enter the programme item.
CLEAN CAPPUCCINO
g T Turn the Rotary Switch until RINSE CAPPUCCINO is
displayed.
k T Press the Rotary Switch to start the rinse operation.
CAPPU. RINSING, the frother is rinsed.
The procedure stops automatically. COFFEE READY
appears on the display.
Disassembling and
rinsing the
Professional
Cappuccino Frother
T Carefully remove the frother from the Connector System©
by twisting slightly.
T Dismantle the frother completely.
T Rinse all the frother parts thoroughly under running water.
T Reassemble the frother.
E Ensure that the individual parts are correctly and firmly
attached to one another to ensure optimum function of the
frother.
T Firmly attach the frother to the Connector System©.
Downloaded from CoffeeMachineManual.com Manuals
39
5 Maintenance
Disassembling and
rinsing the Easy
Cappuccino Frother
T Carefully remove the frother from the Connector System©
by twisting slightly.
T Dismantle the frother completely.
T Rinse all the frother parts thoroughly under running water.
T Reassemble the frother.
E Ensure that the individual parts are correctly and firmly
attached to one another to ensure optimum function of the
frother.
T Firmly attach the frother to the Connector System©.
Cleaning the machine
CAUTION
After 220 coffee preparations or 80 switch-on rinses, the IMPRESSA
will prompt you to clean it.
If the wrong cleaning agent is used, the machine could be damaged
and/or traces of detergent could be left behind in the water.
T Use only original JURA care products.
E The cleaning programme only lasts about 20 minutes.
E Do not interrupt the cleaning programme. The quality of
cleaning will be impaired if you do so.
E JURA cleaning tablets are available from stockists.
@ You can also try out the ‘Cleaning the machine’ operation
online. Visit the Knowledge Builder at www.jura.com.
Cleaning following a
prompt
Precondition: COFFEE READY / CLEAN MACHINE is displayed, and the maintenance button c lights up.
c T Press the maintenance button.
DURATION 20 MIN. / START YES
E If you want to clean the machine at a later point in time, turn
the Rotary Switch until START NO is displayed. Exit the
maintenance programme by pressing the Rotary Switch. The
prompt ‘Clean machine’ remains on the display.
c T Press the maintenance button.
EMPTY TRAY
Downloaded from CoffeeMachineManual.com Manuals
40
5 Maintenance
T Empty the drip tray and coffee grounds container and put
them back into the machine.
PRESS RINSE, the maintenance button c lights up.
T Place a receptacle under the coffee spout and the frother.
c T Press the maintenance button.
CLEANS, the cleaning operation starts.
The process is interrupted. ADD TABLET / PRESS
RINSE, the maintenance button c lights up.
T Open the cover of the filler funnel for pre-ground coffee.
T Insert a JURA cleaning tablet into the filler funnel.
T Close the cover of the filler funnel.
c T Press the maintenance button.
CLEANS, water flows out of the coffee spout and the frother several times.
E You can follow the current status of cleaning on the progress
bar.
The process is interrupted, EMPTY TRAY.
T Empty the drip tray and coffee grounds container and put
them back into the machine.
The cleaning operation is now complete. The IMPRESSA is
ready for use again.
Manual cleaning
You can initiate the ‘Cleaning the machine’ operation manually.
Precondition: COFFEE READY is displayed.
T Open the cover of the Rotary Switch.
k T Keep the Rotary Switch pressed until MAINTENANCE
appears.
k T Press the Rotary Switch to enter the programme item.
CLEAN CAPPUCCINO
g T Turn the rotary switch until CLEAN MACHINE is displayed.
k T Press the Rotary Switch.
DURATION 20 MIN. / START YES
T Continue with the second prompt to take action (indicated
by a T), as is described under ‘Cleaning following a prompt’.
Downloaded from CoffeeMachineManual.com Manuals
41
5 Maintenance
Descaling the machine
CAUTION
The IMPRESSA builds up deposits of limescale over time and automatically prompts you to descale it when necessary. The degree of
calcification depends on the degree of hardness of your water.
If the descaling agent comes into contact with the skin or eyes, this
can cause irritation.
T Avoid contact with the skin or eyes.
T Rinse the descaling agent off with clean water. Should you get
any descaling agent in your eye, see a doctor.
CAUTION
If the wrong descaling agent is used, the machine could be damaged and/or traces of detergent could be left behind in the water.
T Use only original JURA care products.
CAUTION
If the descaling operation is interrupted, there may be damage to
the machine.
T Allow the descaling program to run to the end.
CAUTION
If the descaling agent comes into contact with sensitive surfaces,
damage cannot be ruled out.
T Clean up any splashes immediately.
E The descaling programme lasts approx. 45 minutes.
E JURA descaling tablets are available from stockists.
E If you use a CLARIS filter cartridge and this is activated, you
will not be prompted to change the filter.
@ You can also try out the ‘Descaling the machine’ operation
online. Visit the Knowledge Builder at www.jura.com.
Descaling following a
prompt
Precondition: COFFEE READY / DECALCIFY MACHINE is
displayed and the maintenance button c lights up.
c T Press the maintenance button.
DURATION 45 MIN. / START YES
E If you want to descale the machine at a later point in time, turn
the Rotary Switch until START NO is displayed. Exit the
maintenance programme by pressing the Rotary Switch. The
prompt ‘Decalcify machine’ remains on the display.
c T Press the maintenance button.
EMPTY TRAY
Downloaded from CoffeeMachineManual.com Manuals
42
5 Maintenance
T Empty the drip tray and coffee grounds container and put
them back into the machine.
SOLVENT IN TANK
T Remove the water tank and empty it.
T Completely dissolve the contents of one blister (3 JURA descaling tablets) in a container that holds 600 ml of water. This
may take several minutes.
T Pour the solution into the empty water tank and insert it in
the machine.
SOLVENT IN TANK / PRESS RINSE, the maintenance button c lights up.
T Remove the frother from the Connector System©.
T Place a receptacle under the hot water spout and another
under the Connector System©.
c T Press the maintenance button.
DECALCS, water flows out of the Connector System© and
the hot water spout. The maintenance button c flashes
during the descaling operation.
E You can follow the current status of descaling on the progress
bar.
The process is interrupted, EMPTY TRAY.
T Empty the receptacles below the hot water spout and the
Connector System©.
T Empty the drip tray and coffee grounds container and put
them back into the machine.
RINSE WATER TANK / FILL WATER TANK
T Remove the water tank and rinse it thoroughly.
T Fill the water tank with fresh, cold water and reinsert.
PRESS RINSE, the maintenance button c lights up.
T Refit the frother.
T Place a receptacle under the coffee and hot water spout and
another under the frother.
c T Press the maintenance button.
DECALCS, water flows out of the frother and the hot water
spout.
The process is interrupted, HEATING UP.
MACHINE RINSING, water flows out of the coffee
spout. The operation stops automatically, EMPTY TRAY.
Downloaded from CoffeeMachineManual.com Manuals
43
5 Maintenance
T Empty the drip tray and coffee grounds container and put
them back into the machine.
The descaling operation is now complete. Your IMPRESSA
heats up and is once again ready to use.
E If the descaling operation stops unexpectedly, rinse the water
tank thoroughly.
Manual descaling
You can initiate the ‘Descaling the machine’ operation manually.
Precondition: COFFEE READY is shown on the display and the
filter is not activated.
T Open the cover of the Rotary Switch.
k T Keep the Rotary Switch pressed until MAINTENANCE
appears.
k T Press the Rotary Switch to enter the programme item.
CLEAN CAPPUCCINO
g T Turn the Rotary Switch until DECALCIFY MACHINE
is displayed.
k T Press the Rotary Switch.
DURATION 45 MIN. / START YES
T Continue with the second prompt to take action (indicated
by a T), as is described under ‘Descaling following a prompt’.
Changing the filter
E After 50 litres of water have flowed through, the filter will
cease to work. Your IMPRESSA will automatically prompt you
to replace the filter.
E After two months, the filter will cease to work. Monitor the
elapsed time by adjusting the date plate on the cartridge
holder.
E If the CLARIS filter cartridge is not activated, you will not be
prompted to change the filter.
@ You can also try out ‘Changing the filter’ online. Visit the
Knowledge Builder at www.jura.com.
Downloaded from CoffeeMachineManual.com Manuals
44
5 Maintenance
Change following a prompt
To change the CLARIS filter cartridge when prompted to do so by
your IMPRESSA, proceed as follows:
Precondition: COFFEE READY / CHANGE FILTER is displayed, and the maintenance button c lights up.
c T Press the maintenance button.
DURATION 2 MIN. / START YES
E If you want to change the filter at a later point in time, turn the
Rotary Switch until START NO is displayed. Exit the maintenance programme by pressing the Rotary Switch. The prompt
‘Change filter’ remains on the display.
c T Press the maintenance button.
CHANGE FILTER / PRESS RINSE
T Remove the water tank and empty it.
T Lift the cartridge holder.
T Take out the old CLARIS filter cartridge and the extension.
T Fit the extension on top of a new filter cartridge.
T Insert the filter cartridge into the water tank, exerting slight
pressure.
T Close the cartridge holder. It will click into place audibly.
T Fill the water tank with fresh, cold water and reinsert.
T Place a receptacle (at least 500 ml) under the frother.
E If you are using the Professional Cappuccino Frother, set the
selection lever of the frother to the steam position n.
c T Press the maintenance button.
FILTER RINSING, water flows out of the frother.
E You can interrupt filter rinsing at any time. To do this, press
any button.
E The water may be slightly discoloured. This is not harmful to
health and does not affect the taste.
Filter rinsing stops automatically after approx. 500 ml. The
IMPRESSA heats up and is once again ready to use.
Downloaded from CoffeeMachineManual.com Manuals
45
5 Maintenance
Manual filter change
You can initiate the ‘Changing the filter’ operation manually.
Precondition: The filter is activated and COFFEE READY is
shown on the display.
T Open the cover of the Rotary Switch.
k T Keep the Rotary Switch pressed until MAINTENANCE
appears.
k T Press the Rotary Switch to enter the programme item.
CLEAN CAPPUCCINO
g T Turn the Rotary Switch until CHANGE FILTER is displayed.
k T Press the Rotary Switch.
DURATION 2 MIN. / START YES
T Continue with the second prompt to take action (indicated
by a T), as is described under ‘Replacement following a
prompt’.
Cleaning the
bean container
WARNING
Coffee beans may be covered with a slight oil film which remains on
the walls of the bean container. These residues may negatively affect
the coffee results. For this reason clean the bean container from
time to time.
Danger of injury to the fingers when the grinder is running.
T Switch the machine off with the on/off button Q before performing any work on the grinder.
T Switch the machine off at the power switch 3.
T Open the cover of the bean container and remove the aroma
preservation cover.
T Remove the beans with a vacuum cleaner.
T Loosen the screw in the bean container and lift up the finger
protection.
T Remove the remaining beans with a vacuum cleaner.
T Clean the bean container with a soft, dry cloth.
T Put the finger protection down again and screw it back
tightly in place.
T Fill the bean container with coffee beans, then close the
aroma preservation cover and the bean container cover.
Downloaded from CoffeeMachineManual.com Manuals
46
5 Maintenance
Descaling the water
tank
Limescale deposits may form in the water tank. To ensure correct
function of your IMPRESSA, you should descale the water tank from
time to time.
T Remove the water tank.
T If you use a CLARIS filter cartridge, remove this.
T Descale the tank with a mild, commercially available descaling agent in accordance with the instructions of the manufacturer.
T Rinse the water tank with clean water afterwards.
T If you use a CLARIS filter cartridge, insert this again.
T Fill the water tank with fresh, cold water and reinsert.
Downloaded from CoffeeMachineManual.com Manuals
47
6 Display messages
6 Display messages
Message
Cause/Result
Action
FILL WATER TANK
The water tank is empty.
You cannot prepare any coffee
products, hot water or milk
products.
T Fill the water tank (see
Chapter 1, ‘Preparing and using
for the first time – Filling the
water tank’).
EMPTY GROUNDS
The coffee grounds container
is full. You cannot prepare any
coffee products, but you can
prepare hot water or milk.
T Empty the coffee grounds
container and the drip tray.
EMPTY TRAY
The drip tray is full. You cannot T Empty the drip tray.
prepare any coffee products,
hot water or milk products.
TRAY MISSING
The drip tray is not inserted
correctly or is not inserted at
all. You cannot prepare any
coffee products, hot water or
milk products.
T Insert the drip tray.
T Clean the metal contacts on
the back of the drip tray.
FILL BEANS
The bean container is empty.
You cannot prepare any coffee
products, but you can prepare
hot water or milk.
T Fill the bean container (see
Chapter 1, ‘Preparing and using
for the first time – Filling the
bean container’).
PRESS RINSE
The IMPRESSA is prompting
you to start a rinse operation
or continue a started maintenance programme.
T Press the maintenance button
to start rinsing or to continue the
maintenance programme.
COFFEE READY /
RINSE CAPPUCCINO
The IMPRESSA is prompting
you to start cappuccino
rinsing.
T Press the maintenance button
to start cappuccino rinsing.
COFFEE READY /
CLEAN MACHINE
After 220 preparations or
80 switch-on rinses, the
IMPRESSA will prompt you to
clean it.
T Clean the machine (see
Chapter 5, ‘Maintenance –
Cleaning the machine’).
Downloaded from CoffeeMachineManual.com Manuals
48
6 Display messages
Message
Cause/Result
Action
COFFEE READY /
CLEAN NOW
After 250 preparations the
IMPRESSA will prompt you
to clean it.
T Clean the machine (see
Chapter 5, ‘Maintenance – Cleaning the machine’).
COFFEE READY /
The IMPRESSA is prompting
DECALCIFY MACHINE you to descale it.
T Descale the machine (see
Chapter 5, ‘Maintenance – Descaling the machine’).
COFFEE READY /
DECALCIFY NOW
The IMPRESSA is prompting
you to descale it.
T Descale the machine (see
Chapter 5, ‘Maintenance – Descaling the machine’).
COFFEE READY /
CHANGE FILTER
After 50 litres of water have
flowed through, or after two
months, the filter will cease
to work.
T Replace the CLARIS filter
cartridge (see Chapter 5
‘Maintenance – Changing the
filter’).
COFFEE READY /
CHANGE NOW
After 55 litres of water have
flowed through, the filter will
cease to work.
T Replace the CLARIS filter
cartridge (see Chapter 5
‘Maintenance – Changing the
filter’).
NOT ENOUGH
PRE-GROUND
T The next time you make coffee
There is too little pre-ground
use more pre-ground coffee
coffee in the filler funnel. The
IMPRESSA stops the operation. (refer to Chapter 3, ‘Preparation
at the touch of a button –
Pre-ground coffee’).
Downloaded from CoffeeMachineManual.com Manuals
49
7 Troubleshooting
7 Troubleshooting
Problem
Cause/Result
Action
Grinder is making a very
loud noise.
There are foreign objects
in the grinder.
T Contact Customer Support in your
country (see ‘JURA contact details /
Legal information’).
The frother does not
produce enough milk foam
or milk sprays from the
cappuccino frother.
The cappuccino frother
is dirty or incorrectly
attached.
T Rinse and clean the cappuccino
frother (see Chapter 5, ‘Maintenance –
Cappuccino frother‘).
T Assemble the cappuccino frother
correctly and firmly attach the frother
to the Connector System© (refer to
Chapter 5 ‘Maintenance – Disassembling and rinsing the frother’).
Coffee only comes out
in drips when it is being
prepared.
Coffee or pre-ground
coffee has been ground
too finely and is blocking
the system.
T Put the grinder on a coarser setting
or use coarser pre-ground coffee (refer
to Chapter 1, ‘Preparing and using for
the first time – Adjusting grinder’).
Water hardness cannot
be adjusted.
The CLARIS filter
cartridge is activated.
T Deactivate the CLARIS filter cartridge
in programming mode.
COFFEE READY /
FILL BEANS
The grinder is not yet
completely filled with
beans.
T Prepare a coffee speciality.
The bean monitor is
dirty.
T Clean the bean container
(see Chapter 5, ‘Maintenance –
Cleaning the bean container’).
is displayed although
the bean container has
been filled.
COFFEE READY /
FILL BEANS is not
displayed although the
bean container is empty.
EMPTY TRAY
is always displayed.
FILL WATER TANK
is displayed although
the water tank is full.
The metal contacts of the T Clean and dry the metal contacts
drip tray are dirty or wet. on the back of the drip tray.
The water tank float is
trapped.
T Descale the water tank (see
Chapter 5, ‘Maintenance –
Descaling the water tank’).
Downloaded from CoffeeMachineManual.com Manuals
50
7 Troubleshooting
Problem
Cause/Result
Action
ERROR 2 is displayed.
If the machine was
exposed to the cold for a
long period of time, it is
disabled from heating up
due to safety reasons.
T Warm up the machine at room
temperature.
Other ERROR messages
are displayed.
–
T Turn the IMPRESSA off at the power
switch. Contact Customer Support in
your country (see ‘JURA contact
details / Legal information’).
E If you have not been able to solve the problem, contact
Customer Support in your country (see ‘JURA contact
details / Legal information’ ).
Downloaded from CoffeeMachineManual.com Manuals
51
8 Transport and environmentally neutral disposal
8 Transport and environmentally neutral disposal
Transport / Emptying
the system
Keep the packaging for your IMPRESSA. It should be used to protect
the machine during transportation.
In order to protect the IMPRESSA from frost during transportation,
the system must be emptied.
Precondition: COFFEE READY is displayed.
k T Keep the Rotary Switch pressed until MAINTENANCE
appears.
g T Turn the Rotary Switch until RESET is displayed.
k T Press the Rotary Switch to enter the programme item.
RESET / PRODUCT
g T Turn the Rotary Switch until RESET / EMPT.SYST. is
displayed.
k T Press the Rotary Switch.
EMPTY WATER TANK
T Remove the water tank.
PRESS RINSE, the Maintenance button c lights up.
T Place one receptacle under the hot-water spout and another
under the cappuccino frother.
c T Press the Maintenance button.
SYSTEM EMPTYING, a small amount of water flows out
of the hotwater spout and the cappuccino frother. The
operation stops automatically and your IMPRESSA switches
off.
E The next time you use the machine the system must be
refilled (see Chapter 1, ‘Preparing and using for the first
time – First-time use’).
Disposal
Please dispose of old machines in an environmentally neutral way.
H
Old machines contain valuable materials capable of being recycled
which should be salvaged for recycling. Please therefore dispose of
old machines via your regional collection system.
Downloaded from CoffeeMachineManual.com Manuals
52
9 Technical data
9 Technical data
Voltage
220–240 V ~, 50 Hz
Power
1450 W
Marks of conformity
AS
Airborne noise emitted
Lp < 70 dB (A)
Energy SAVE NO
40 Wh
Energy SAVE LEVEL 1
20 Wh
Energy SAVE LEVEL 2
15 Wh
Pump pressure
Static max. 15 bar
Holding capacity of water tank
5.7 l
Holding capacity of bean
container
280 g
Holding capacity of coffee
grounds container
Approx. 40 servings
Cable length
Approx. 1.1 m
Weight
13.8 kg
Dimensions (W x H x D)
41 x 47 x 39 cm
Downloaded from CoffeeMachineManual.com Manuals
53
Index
Index
A
B
Energy-saving mode 30
Entering a default setting for the amount of
water for a cup size 18
Errors
Aroma preservation cover 4
Automatic switch-off 31
Bean container
Troubleshooting 50
Espresso 23
F
Aroma preservation cover 4
Cleaning 46
Cover 4
Filling 10
C
Restore factory settings 32
Filler funnel for pre-ground coffee 4
Filling
Bean container 10
Water tank 9
Cappuccino 24
Cappuccino frother
Filter
Changing 44
Using and activating 11
Cleaning 36
Easy Cappuccino Frother 9
Professional Cappuccino Frother 9
Rinsing 38
Fineness of grind
Adjusting grinder 13
Fineness of grind switch 4
CLARIS filter cartridge
Fineness of grind switch 4
First-time use 10
Frother
Changing 44
Using and activating 11
Cleaning
Bean container 46
Cappuccino frother 36
Machine 40
Coffee 23
Coffee à la carte 24
Coffee grounds container 4
Coffee spout, height-adjustable 4
Connector System© 4, 9
Control options 16
Cover
Bean container 4
Filler funnel for pre-ground coffee 4
D
Descaling
Machine 42
Water tank 47
Display messages 48
Display, Messages 48
Drip tray 4
E
Easy Cappuccino Frother
Disassembling and rinsing 40
Emptying the system 52
Factory settings
Easy Cappuccino Frother 9
Professional Cappuccino Frother 9
H
Hardness of water 12
Hot milk 26
Hot water 27
Hot water portion 27
Hot water spout 4
I
L
M
Internet 9
Language 34
Latte macchiato 24
Machine
Cleaning 40
Descaling 42
Rinsing 37
Setting up 9
Switching off 15
Switching on 14
Maintenance 36
Maintenance tips 36
Downloaded from CoffeeMachineManual.com Manuals
54
Index
Milk
Hot 26
Milk portion 26
S
Milk foam 26
O
P
Entering a default setting for the amount of
water for a cup size 18
One-off settings before and during preparation 17
Permanent settings in programming mode
28
Restore factory settings 32
One-off settings before and during preparation 17
Permanent settings in programming mode
28
Power switch 4
Pre-ground coffee 25
Filler funnel 4
Pre-ground coffee 25
Preparation
At the touch of a button 23
Cappuccino 24
Coffee 23
Coffee à la carte 24
Espresso 23
Hot water 27
Latte macchiato 24
Milk 26
Pre-ground coffee 25
Problems
Troubleshooting 50
Professional Cappuccino Frother 4, 9
Disassembling and rinsing 39
Programming mode 28
Automatic switch-off 31
Energy-saving mode 30
Language 34
Products 28
Rinses 31
Unit amount of water 34
R
Safety 6
Selector switch 5
Settings
Setting up 9
Switching off 15
Switching on 14
T
U
Technical data 53
Troubleshooting 50
Use
Proper 6
Use, First time 10
V
Viewing information and maintenance status
21
Viewing maintenance status 21
W
Water hardness 12
Determining and adjusting 12
Water tank 4
Descaling 47
Filling 9
Reset
Restore factory settings 32
Restore factory settings 32
Rinses 31
Rinsing
Cappuccino frother 38
Machine 37
Rotary switch 5
Downloaded from CoffeeMachineManual.com Manuals
55
Art. 69201/XS95/en/201003
JURA contact details / Legal information
Your JURA dealer:
JURA Elektroapparate AG
Kaffeeweltstrasse 10
CH-4626 Niederbuchsiten
Tel. +41 62 38 98 233
www.jura.com
Directives
The machine complies with the following directives:
Z 2006/42/EC – Machinery Directive
Z 2004/108/EC – Electromagnetic Compatibility
Z 2009/125/EC – Ecodesign
Technical changes
We reserve the right to make technical changes. The illustrations
used in the IMPRESSA XS95/XS90 One Touch Manual show the
IMPRESSA XS95 One Touch model. Your IMPRESSA could incorporate minor changes.
Feedback
Your opinion is important to us! Use the contact link at
www.jura.com.
Copyright
The Instructions for Use contain information which is protected by
copyright. It is not permitted to photocopy or translate these
Instructions for Use into another language without the express
written consent of JURA Elektroapparate AG.
Downloaded from CoffeeMachineManual.com Manuals
56