OIL WELL TOOLS
A Division of DAWSON ENTERPRISES
®
TM
Manufacturer of original design quality well servicing products
CAVINS “ADVANCE” AUTOMATIC
SPIDERS
For Casing-Tubing and Drill Pipe
OIL WELL TOOLS
Fig. 1
Air operated “Advance” Model “C” Spider with full circle
replaceable inserts.
2853 Cherry Avenue
Signal Hill, CA 90755
Ph: (562) 424-8564
Fax: (562) 595-6174
The “Advance” Spider developed by Cavins Oil Well Tools is
considered to be the pioneer in power slips. Through years of
experience and testing, many improvements have been made
which make the Cavins “Advance” Spider the leader for a safe,
economical, and trouble-free handling of tubular goods. Heat treated alloy steel is used throughout for the greatest possible strength
and the longest wearing life with a minimum of weight. The shafts
are hardened alloy steel for longer life. Replaceable steel bushings
are fitted into the journal bearings. All bearings and journals are
equipped with grease fittings for lubrication. Air Cylinders and Foot
Valves are mist lubricated through the airstream. All Cavins
“Advance” Spiders are equipped with a manually operated safety
latch which may be used to positively lock the slips in their set
position. Because of the low operating pressure the slips cannot
release from the tubing until it has been raised by the elevators,
thus guarding against a lost string in the event that the Foot Valve
is tripped accidentally. The Slips, Shafts, and Air Operating
Mechanisms are protected by guards to prevent damage caused
by the elevators or other outside forces. Through research and
field testing our engineers are constantly on the look out for additional improvements which will assure the personnel in the field of
receiving the safest and most maintenance free equipment that is
available.
The Cavins “Advance” Spider is available in five models, Model
“B”, “C”, “C-HD”, “F”, and “G”. All are designed for manual, compressed air, or hydraulic operation with the exception of the Model
“G” which is available for compressed air or hydraulic operation
only.
All Cavins “Advance” Spiders may be used on a rotary table
with an adapter plate that fits into the square drive or pin drive
master bushing, centering the Spider on the rotary table. This also
permits the manually operated Spider to be rotated.
Models “B”, “C”, and “C-HD” Spiders may be equipped with a
Gate and Slips which are relieved to pass parallel strings of tubing. If the Spider is to be used with both single and parallel strings
to any extent, it is recommended that both kinds of Slips and
Gates be ordered. A standard feature of all Cavins “Advance”
Spiders is a specially designed Gate Section which will allow the
running of an electric submersible pump cable simultaneously with
any size tubing string.
Fig. 2
Advance Mode “B” Spider (hand operated)
CAVINS “ADVANCE” SPIDERS
SPECIFICATIONS
MODEL “B”
MODEL “C”
MODEL “CHD”
MODEL “F”
MODEL “G”
HEIGHT
BASE DIMENSION
GATE OPENING
BOWL OPENING
TUBULAR RANGE
MAXIMUM LOAD
CAPACITY
15-1/2”
14" X 17"
4-1/4"
4-3/4" DIA.
1.315" to 3-1/2"
55 Tons
110,000 Lbs.
16-1/2”
16-1/2" X 18-1/2"
5-3/4"
6-1/2" DIA.
1.315" to 5-1/2"
82.5 Tons
165,000 Lbs.
16-1/2"
16-1/2" X 18-1/2"
5-3/4"
6-1/2" DIA.
1.315" to 5-1/2"
125 Tons
250,000 Lbs.
26-3/4"
28" X 28"
8-3/4"
10-1/8" DIA.
2-3/8" to 8-5/8"
200 Tons
400,000 Lbs.
35"
41" X 41-5/8"
13-3/4"
15-1/2" DIA.
2-3/8" to 13-3/8"
350 Tons
700,000 Lbs.
2
2853 Cherry Avenue
Signal Hill, CA 90755
Ph: (562) 424-8564
Fax: (562) 595-6174
CAVINS “ADVANCE” SPIDERS
MODEL “F” AND “G”
OIL WELL TOOLS
MODEL “F” SPIDERS AFFORD MANUAL, PNEUMATIC, and HYDRAULIC OPERATION
The CAVINS “Advance” Model “F” Automatic Spider is another
industry tested and proven tool. Similar to the Model “B” and Model
“C” Spiders, the Model “F” offers manual, pneumatic(air) or
hydraulic operation mechanisms. The Model “F” Spider (Fig. 1) can
handle tubular goods ranging in size from 2-3/8" O.D. through 85/8" O.D. and is favored for automation in light drilling operations
or for heavy workover and production rigs. The load capacity for
the Model “F” Spider is 400,000 lbs. NOW the Model “F” Spider is
available also with CAVINS patented, Type “FCR” Full Circle Slips,
(Fig. 2) with Replaceable Type “FCI” Inserts. The conventional,
Type “TD” Slips, (Fig. 3) with Replaceable Inserts are also available.
Fig. 2
“FCR” Type, Full Circle
Slips, available with “FCI”
Replaceable Inserts.
Fig. 3
“TD” Type, Conventional
Slips, available with
Replacement Inserts.
Fig. 1
Cavins Model “F” Spider, the long time favorite for dependable service now
meets the cost conscious production criteria with Full Circle Slips that feature replaceable “FCI” Inserts.
MODEL “G” SPIDERS FOR HEAVY DRILLING OPERATIONS
For heavy drilling operations, up to 700,000 pounds (350 tons)
hook load capacity; the CAVINS “Advance” Model “G” Automatic
Spider, (Fig. 4) is recommended where heavy duty, dependable
service applies. The Model “G” Spider will handle tubular goods
ranging in size 2-3/8" through 13-3/8" O.D. and is available for
pneumatic (air) or hydraulic operation. Like all CAVINS “Advance”
Spiders, the Model “G” utilizes a minimum of moving parts for ease
of operation and very minimal maintenance. CAVINS patented and
proven Type “FCR” Full Circle Slips (Fig. 2 and 5) with replaceable
Type “FCI” Inserts, are used for the complete range of sizes in the
Model “G” Spider. The long 16" gripping area plus 360˚ degree,
100% contact of the Type “FCI” Inserts, makes it the most positive
pipe holding device of its kind. Competition can boast only a maximum of 70% contact of the pipe. The clear advantage being
greater contact area causing far less chance of damaging or
crimping heavy strings of pipe. Another proven asset of the
CAVINS unique design is that there is no need for costly pipe
guides to attach to the spider because the Slips and Inserts withdraw completely from the Spider Bowl and when disengaged
allows full protection from damage by the string when it is in
motion.
Fig. 4
Master Slip Bodies with companion
Replaceable Inserts afford the
greatest economy for working a
wide range of tubular goods sizes.
Fig. 5
3
CAVINS INVERTED SPIDERS
2853 Cherry Avenue
Signal Hill, CA 90755
Ph: (562) 424-8564
Fax: (562) 595-6174
FOR “SNUBBING” OPERATIONS
U.S. Pat. #2,846,877
OIL WELL TOOLS
Hydraulic work over (Snubbing) services are increasingly
favored, having the advantage of eliminating the need to kill
the well. It lowers the cost as well as the time and problems
associated with circulating salt water, mud and other fluids.
The Cavins “Advance” Model “C,” “C-HD,” and “F” Spiders
have specifically been designed for snubbing operations. It
can work in its right side up position (Fig. 2) or in the inverted
upside down position (Fig. 1). The Spider Body and Slips are
specially designed for this service. The gripping Inserts however, are of standard design and are interchangeable with the
regular Cavins Spiders. Tubular Goods from 1.315" (1" O.D. to
5-1/2" O.D. can be handled with a clear opening for 6.050"
O.D. casing coupling with the Model “C” and “C-HD” Spiders.
Tubular goods 2-3/8" O.D. to 8-5/8" O.D. can be run with the
Model “F” Spider. All Spider models can be either hydraulic or
compressed air operated. A minimum of moving parts
assures a trouble-free operation.
A typical set of spiders on a snubbing rig is illustrated in
Fig. 3. Four spiders may be used: two (2) in the regular
(upright) position and two (2) in the inverted (snubbing) position. One regular and one inverted spider are stationary and
the other regular and inverted spiders are mounted on the
traveling piston. The traveling spiders are used to either push
the pipe into the well or pull it from the well while the stationary spiders are used to hold the string of pipe when the traveling spiders are not engaged.
Fig. 2
TRAVELING SPIDERS
A INVERTED
B REGULAR
WORKBASKET FOR
MEN & EQUIPMENT
A
[ OPEN ]
[ CLOSED ]
A
B
[ CLOSED ]
B
[ OPEN ]
TRAVELING
PISTON
TRAVELING PISTON
HYDRAULIC CONTROL FLUID
INLET AND OUTLET
HOSE CONNECTIONS
STATIONARY SPIDERS
C INVERTED
D REGULAR
C
[ OPEN ]
D
[ OPEN ]
C
[ OPEN ]
[ CLOSED ]
D
Fig. 3
A typical snubbing operation employing two inverted spiders and two regular
(upright) spiders.
A Cavins Inverted
Spider and Regular
Spider in opposing
positions for hydraulic
work over (snubbing)
operation.
Fig. 1
Fig. 4
Cavins Model “C-HD” Spiders will handle tubular goods in a size range
of 1" to 5-1/2" O.D. with a maximum load capacity of 250,000 pounds
4
2853 Cherry Avenue
Signal Hill, CA 90755
Ph: (562) 424-8564
Fax: (562) 595-6174
“FULL CIRCLE” SLIPS
REMOVABLE INSERTS
OIL WELL TOOLS
CAVINS
“ADVANCE”
SPIDERS
PATENTED
CAVINS Model “C”
“Advance” Spider
with patented
The Cavins “Full Circle” Slips,
360°
(Type “FCR”) with removable inserts
degree
were designed to replace Full Circle
FULL CIRCLE SLIPS
Slips with integral teeth. The “FCR”
Full Circle Slips surround the pipe
360 degrees and exert a uniform gripType “FCR”
ping power on the pipe to avoid deformation, bottle-necking, or crushing. A
heavy-duty steel pin retains each insert
securely in each slip body segment. The cotter key secures the retaining pin in place.
THREE DISTINCT ADVANTAGES ARE REALIZED WITH THIS NEW DESIGN:
1. It eliminates the purchase of individual slips for every size of tubular goods.
2. The Slip Body is made of tough alloy steel for maximum strength while the
inserts are of case hardened steel for longer wear.
3. Since only a minimum of Slip Bodies are required to cover the range of
tubular goods for each spider, the investment compares less than it would
with the purchase of individual slips for each size pipe.
For the Cavins “Advance” Model “B” Spider, only one type “FCR” Slip
Body is required, with removable inserts, (TYPE “FCI”). One set of (4) inserts
is required for each size of Tubular Goods:
The 2-7/8", Type “FCR” Master Slip Body takes inserts for 2-7/8", 23/8", 2-1/16", 1.900 (1-1/2"), 1.660 (1-1/4"), and 1.315 (1") O.D. tubular
goods.
To handle 3-1/2" O.D. Tubing, it is necessary to use a Type “TD” Slip
Body with either Chevron, (Type “CI”) Replaceable Inserts or button
(Type “CBI”) Replaceable Inserts.
For the Cavins “Advance” Model “C” and “C-HD” Spiders, three (3)
types of “FCR” Slip Bodies are available with Removable Inserts, (Type “FCI”).
One set of (4) inserts is required for each size of Tubular Goods:
The 2-1/16", Type “FCR” (-1) Master Slip Body takes Inserts for 2-1/16",
1.900" (1-1/2"), 1.660" (1-1/4") and 1.315 (1") O.D. Tubular Goods.
The 3-1/2" Type “FCR” (-2) Master Slip Body takes Inserts for 3-1/2",
2-7/8", and 2-3/8" O.D. Tubular Goods.
The 4-1/2" Type “FCR” (-3) Master Slip Body takes Inserts for 4-1/2",
4", and 3-1/2" O.D. Tubular Goods.
For the Cavins “Advance” Model “F” Spider, three (3) Type “FCR”
Master Slip Bodies are available with Removable Inserts, (Type “FCI”). One set
of (4) inserts is required for each size of Tubular Goods:
The 3-1/2" Type “FCR” Slip Body takes Inserts for 3-1/2", 2-7/8", and
2-3/8" O.D. Tubular Goods.
The 5-1/2" Type “FCR” Master Slip Body takes Inserts for 5-1/2", 5",
4-1/2", and 4" O.D. Tubular Goods.
The 7-5/8" Type “FCR” Master Slip Body takes Inserts for 7-5/8", 7",
and 6-5/8" O.D. Tubular Goods.
For the Cavins Model “G” Spider, six (6) Type “FCR” Master Slip Bodies
are available with Removable Inserts, (Type “FCI”). One set of (8) inserts is
required for each of two larger sizes of Tubular Goods and one set of (4)
inserts each for the other sizes:
The 3-1/2" Type “FCR” Master Slip Body takes Inserts for 3-1/2", 27/8", and 2-3/8" O.D. Tubular Goods.
The 5-1/2" Type “FCR” Master Slip Body takes Inserts for 5-1/2", 5",
4-1/2" and 4" O.D. Tubular Goods.
The 7-5/8" Type “FCR” Master Slip Body takes Inserts for 7-5/8", 7",
and 6-5/8" O.D. Tubular Goods.
The 9-5/8" Type “FCR” Master Slip Body takes Inserts for 9-5/8" and
8-5/8" O.D. Tubular Goods.
The 11-3/4" Type “FCR” Master Slip Body takes Inserts for 11-3/4"
and 10-3/4" O.D. Tubular Goods.
Full Circle Slip Inserts are available for Cavins “Advance” Spiders, Models
“B”, “C”, “C-HD”, “F”, and “G”
The 13-3/8" Type “FCR” Master Slip Body takes Inserts for 13-3/8"
O.D. Tubular Goods.
5
SPIDERS ACCESSORIES
FOR MODELS “B,” “C,” “F” AND “G” SPIDERS
2853 Cherry Avenue
Signal Hill, CA 90755
Ph: (562) 424-8564
Fax: (562) 595-6174
OIL WELL TOOLS
The Foot Operated Air Control Valve
only is available in a safety cover guard
(Fig. 1). A combination unit is offered
where it is desirable to have the Foot
Valve and the Filter, Regulator and
Lubricator all in one steel case, (Fig. 2)
High pressure (300 P.S.I.) air hoses
with Female Quick Change Connectors
can be supplied in any desired length
(Fig. 3).
Air Filter, (Fig. 4), with Drain (A),
Pressure Regulator with Gauge (B) and
Lubricator (C) assembled into one unit
and supplied with Quick Change Air
Coupling and Mounting Bracket. This unit
can be installed near the Operator’s stand
or under the console. When the rig is
working in extremely high temperature
areas, metal bowls can be supplied in
place of the plastic ones normally furnished on the Filter and Lubricator.
When using the Cavins “Advance”
Spider on a drilling rig for making round
trips, a Rotary Table Master Bushing
Adapter Plate is available which is bolted
to the bottom flange of the Spider. The
Adapter Plate fits into any standard A.P.I.
square drive (Fig. 5) or Pin Drive Master
Bushing (Fig. 6).
(Fig. 3)
Oil-Resistant Air Hose with Female
Quick Change Couplings.
(Fig. 1) PISTON TYPE TB230
Foot-Operated Valve with Safety Cover
Guard and Hose Connections.
(Fig. 2)
Combination Foot Valve. Pressure
Regulator with Gauge and Lubricator,
mounted in Portable Carrying Case.
(Available with Ratchet or Piston Type
Foot Valve).
TB220 with Ratchet Type
TB220-P with Piston Type
(Fig. 1B) RATCHET TYPE TB200
Foot-Operated Valve, Ratchet-Type
with Safety Guard Cover and Hose
Connections.
(Fig. 4)
Air Filter, Pressure Regulator with
Gauge, and Lubricator Unit. TB400
(Fig. 5)
Rotary Table Master Bushing Adapter
Plate for Square Drive.
(Fig. 6)
Rotary Table Master Bushing Adapter
Plate, Pin Drive.
“FULL CIRCLE”
SLIPS
with
REPLACEABLE
INSERTS
The Cavins Full Circle Slip with Removable inserts has been
designed to replace the Integral Full Circle Slip. The new style, type
“FCR” Slip, consists of (4) slip segments, as do all other types of
Cavins Slips. It has the great advantage that the Full Circle Inserts
are replaceable. The Slip Body is made of tough high grade heat
treated alloy steel. The Inserts are also alloy steel, case hardened.
Three Master Slip Bodies are available for the Model “C” Spider.
One Master Slip Body is available for the Model “B” Spider.
6
Type “TD” Slips with replaceable inserts for Model “B” and
Model “C” Spiders. Circular
Button Type Inserts are recommended for light loads.
Available for either single or
parallel strings. (Fig. 7)
Type “TD” Slips with replaceable “Chevron” inserts. Inserts
have 35% greater contact than
the Circular Button type.
Recommended for the heavier
tubular string load. Available
for either single or parallel
strings operation. (Fig. 8)
2853 Cherry Avenue
Signal Hill, CA 90755
Ph: (562) 424-8564
Fax: (562) 595-6174
TUBING SPIDERS
OIL WELL TOOLS
CONVERTIBLE TUBING SPIDERS
50 TON AND 100 TON
Description:
These versatile tubing spiders can
easily be converted from power to manual operation. For power operation, an
air cylinder actuates unitized slips. The
spiders can be quickly converted to
manual operation by substituting a foot
pedal and foot release lever assembly
for the air cylinder.
50 TON MODEL:
Tubing size capacity is 1.315"
through 3-1/2" (33.40 mm - 88.90 mm)
O.D. The slips provide a full 6" (152.40
mm) of vertical gripping length around
the tubing to prevent pipe crimping. The
50-ton model provides a 5-1/2" (139.70
mm) opening through the bowl.
Available in air or manually operated
models.
Options such as guard doors are
available. Cavins/BJ fine-tooth slip
inserts are available in most assembly
sizes and are recommended to reduce
tooth penetration. As a power tool, the
convertible tubing spider can operate
off the regular rig air system or from an
auxiliary trailer-mounted air compressor unit.
100 TON MODEL:
Tubing size capacity is 2-3/8"
through 3-1/2" (60.33 mm - 88.9 mm)
O.D. The slips provide a full 9" (228.60
mm) of vertical gripping length around
the tubing to prevent pipe crimping. The
100-ton model provides a 5-7/8"
(149.23 mm) opening through the bowl.
50 Ton Convertible Tubing Spider
SPECIFICATIONS – FOR 50-TON CONVERTIBLE TUBING SPIDERS
TYPES 50-A (AIR) AND 50-M (MANUAL)
Part
No.
Description
Type 50-A Air-Operated Tubing Spider with Plain Door,
Less Slips, Hoses and Control Assembly
Type 50-A Air-Operated Tubing Spider with Guard Door,
Less Slips, Hoses and Control Assembly
Type 50-M Manually Operated Tubing Spider with
Plain Door, Less Slips
Type 50-M Manually Operated Tubing Spider with
Guard Door, Less Slips
Weight Ea.
lb
Type 100-A Air-Operated Tubing Spider with Guard Door,
Less Slips, Hoses and Control Assembly
Type 100-M Manually Operated Tubing Spider with
Guard Door, Less Slips, Hoses and Control Assembly
Weight Ea.
kg
Description
Part
No.
Insert
P/N
Qty.
lb
kg
2-3/8" (60.33 mm) O.D. Slip Assembly
2-7/8" (73.03 mm) O.D. Slip Assembly
3-1/2" (88.9 mm) O.D. Slip Assembly
35110
35111
35112
29255
24773
24774
9
9
18
45
45
45
20
20
20
29660
173
78
29659
193
87
29662
117
53
29661
137
62
SPECIFICATIONS – FOR 100-TON CONVERTIBLE TUBING SPIDER
TYPES 100-A (AIR) AND 100-M (MANUAL)
Description
SLIP ASSEMBLIES FOR TYPES 100-A AND 100-M
TUBING SPIDERS
Weight Ea.
Part
No.
lb
kg
37841
257
115
37843
200
91
SLIP ASSEMBLIES FOR TYPES 50-A (AIR) AND 50-M (MANUAL)
TUBING SPIDERS
Weight Ea.
Description
Part
No.
Slip
Insert No.
Qty.
lb
kg
1.315" (33.40 mm) O.D. Slip Assembly
1.660" (42.16 mm) O.D. Slip Assembly
1.900" (48.26 mm) O.D. Slip Assembly
2"-2-1/16" (50.8 mm-52.39) O.D. Slip Assembly
2-3/8" (60.33 mm) O.D. Slip Assembly
2-7/8" (73.03 mm) O.D. Slip Assembly
3-1/2" (88.9 mm) O.D. Slip Assembly
29773
29772
29771
29770
29769
29693
29692
29259
29258
29257
29256
29255
24773
24774
6
6
6
6
6
6
12
50
49
48
46
39
38
37
23
22
22
21
18
17
17
*All except 3-1/2" (88.9 mm) Slip Assembly are made out of 2-7/8" (973.03 mm) Slip Bodies.
CONTROL ASSEMBLIES FOR AIR SPIDERS
Weight Ea.
Description
Part
No.
lb–oz
kg
Standard Air Control Assembly complete with single pedal
control valve with base plate and fittings
30362
31–4
14
Air Control Assembly complete with single pedal control
valve with base plate and fittings, filter, lubricator,
regulator with gage and cover
30364
60–0
27
HOSE ASSEMBLIES WITH FITTINGS FOR ALL TUBING SPIDERS
Description
Air Line Hose Assembly (1/4" x 12'–6.35 MM x 3.66 m)–
Air Supply to Control, 1 required
Air Line Hose Assembly (1/4" x 12'–6.35 mm x 3.66 m)–
Control to Spider, 2 required
Air Line Hose Assembly (1/4" x 15'–6.35 mm x 4.57 m)–
Air Supply to Control, 1 required
Air Line Hose Assembly (1/4" x 15'–6.35 mm x 4.57 m)–
Control to Spider, 2 required
Air Line Hose Assembly (1/4" x 25'–6.35 mm x 7.62 m)–
Supply to Control, 1 required
Air Line Hose Assembly (1/4" x 25'–6.35 mm x 7.62 m)–
Control to Spider, 2 required
Weight Ea.
Part
No.
lb–oz
kg
30049
4–8
2
30366
4–8
2
30049-15 5
2.3
30366-15 5
2.3
30049-25 7
3.2
30366-25 7
3.2
7
2853 Cherry Avenue
Signal Hill, CA 90755
Ph: (562) 424-8564
Fax: (562) 595-6174
TUBING SPIDERS
OIL WELL TOOLS
TS-100 TUBING SPIDER
The Baash-Ross TS-100 Tubing
Spider is available in two body sizes for
running a wide range of tubing sizes.
The 3-1/2" Tubing Spider accommodates single or dual strings of tubing.
When running single strings, the spider
will handle any size tubing up thru 3-1/2"
O.D. When running dual strings, the main
tube, which is held by the slips, can be
any size from 1.050" O.D. thru 3-1/2"
O.D. and the auxiliary tube can be any
size up thru 1.660" O.D.
The 5-1/2” Tubing Spider can handle
single, double, or triple strings. When
running single strings the spider will handle from 3-1/2” up to 5-1/2” O.D. tubulars.
When running dual strings, the main
tube, which is held by the slips, can be
from 3-1/2” thru 5-1/2” O.D. and the auxiliary tube can be any size up to 1.900”
O.D. When running triple strings the main
tube is 3-1/2” O.D. and the auxiliary tubes
can be any size thru 1.900” and 1.660”
O.D. respectively.
TS 100
3-1/2" TS 100 TUBING SPIDER
O.D.
Size
Inches
Part no.
Wt
Lbs
Part no.
Wt
Lbs
Bowl only
7502-100
168
7502-101
166
Complete
1.050
1.315
1.660
1.900
2.000
2-1/16
2-3/8
2-7/8
3-1/2
7502-100-H
7502-100-A
7502-100-B
7502-100-C
7502-100-J
7502-100-G
7502-100-D
7502-100-E
7502-100-F
237
235
234
232
230
228
226
225
223
7502-101-H
7502-101-A
7502-101-B
7502-101-C
7502-101-J
7502-101-G
7502-101-D
7502-101-E
7502-101-F
235
233
233
230
228
226
224
223
221
SLIP LINERS FOR 3-1/2" TS-100 TUBING SPIDERS
O.D.
Size
Inches
Slip Assy
3-1/2
2-7/8
2-3/8
2-1/16
2.000
1.900
1.660
1.315
1.050
1
9
9
9
9
9
9
9
9
9
5-1/2" Complete with slips, tong & bowl
Single string
Double string*
Part no.
Part no.
Bowl only
7502-103
200
7502-105
Complete
3-1/2
4
4-1/2
4-3/4
5
5-1/2
7502-103-A
7502-103-B
7502-103-C
7502-103-D
7502-103-E
7502-103-F
300
284
275
270
264
253
7502-105-A
7502-105-B
7502-105-C
7502-105-D
7502-105-E
7502-105-F
Triple string**
Wt
Lbs
Part no.
Wt
Lbs
7502-106
300
284
275
270
264
253
7502-106-A
300
* Up to and including 5-1/2" x 1.900"
** 3-1/2" x 1.900" x 1.660"
SLIPS FOR 5-1/2" TS-100 TUBING SPIDERS
Single string
Double string*
Part no.
Total
Wt Lbs
O.D. Size
Inches
No.
Req’d. Part no.
Total
Wt Lbs
7502-104
7502-A-5069
7502-A-5070
7502-A-5071
7502-A-5072
7502-A-5073
7502-A-5074
7502-A-5075
7502-A-5076
7502-A-5077
43-3/4
11-1/4
13-1/2
14-5/8
18
19-1/8
20-1/4
22-1/2
23-3/8
13-1/2
Tong Assy.
Slips
5-1/2
5
4-3/4
4-1/2
4
3-1/2
2-7/8
2-3/8
1
7502-70
4
4
4
4
4
4
4
4
7502-A-26
7502-D-26
7502-B-26
7502-C-26
7502-G-26
7502-F-26
7502-H-26
7502-K-26
*UP TO AND INCLUDING 3-1/2" X 1.660"
Baash-Ross is a licensed trademark of National Oilwell Varco, L.P.
8
For running a single string of tubing,
both halves of the bowl are smoothbored and identical. For a double string,
or triple string, one half of the bowl is
smooth-bored while the other half is slotted to receive the auxiliary tube or tubes.
The bowl will fit directly into a API standard square in the rotary table, or it can
be bolted to a wellhead flange thru the
slots provided.
Wt
Lbs
Single String and Double String*
No.
Req’d.
The latch automatically locks the slips
around the tubing as the handles are
closed. The latch opens when the operator spreads the handles. The spider bowl
is made in two halves, fastened together
by a hinge pin and removable lock pin.
This design combines strength with ease
of operation and removal.
5-1/2" TS 100 TUBING SPIDER
3-1/2" Complete with slip liners & bowl
Single string
Double string
O.D. Size
Inches
Each body section is recessed to hold
liner segments so stresses of supporting
the tubing are transmitted directly to the
slip body. The liner segments can be
replaced by removing a single pin and
sliding out the segments.
Triple string**
Part no.
Total
Wt Lbs
Part no.
Total
Wt Lbs
29
7502-78
29
7502-107
29
49
60
66
71
80
96
116
132
7502-A-106
7502-D-106
7502-B-106
7502-C-106
7502-G-106
7502-F-106
49
60
66
71
80
96
7502-A-222
96
2853 Cherry Avenue
Signal Hill, CA 90755
Ph: (562) 424-8564
Fax: (562) 595-6174
TUBING SPIDERS
OIL WELL TOOLS
BAASH-ROSS® Open End Tubing Spiders
The Open End Tubing Spider is available in two basic sizes;
one to accommodate slips for 3-1/2" O.D. tubing or smaller,
and the other to handle 4-1/2" O.D. tubing or smaller.
It is placed around the tubing by lifting out a removable end
gate, sliding the bowl into place and dropping the end gate
back into position, where it is locked with a bolt.
The spider is made of heat-treated steel and is rated at 100ton capacity.
The four-slip segments of the tubing spider are firmly hung
to a hinged tong by dovetail grooves in their backs which mate
with tongues inside the tong body.
An automatic tong latch for locking the slips in position can
only be opened by the handles.
The slips are 10" long and provide a large gripping area.
Because they set as a unit, slip pressure is uniform at all
points. Narrow slip backs eliminate sticking and compensate
for wear of the spider body.
TABLE NO. 1
3-1/2" Open End Tubing Spider Complete (Double String)
2", 2-1/2" or 3" production tube with 1-1/4" power tube
(the slips hold production tube only)
Nom. Tubing Size to Hold
with Power Tube
API Tubing Size to Hold
with Power Tube
Wt. Per Set Complete lbs.
Part Number Complete
FIG. 1 – The Open End Tubing Spider, complete, showing Unitized Slip Assembly set in Body.
TABLE NO. 2
4-1/2" Open End Tubing Spider Complete (Double String)
2-1/2" production tube with 1-1/4" power tube,
3" production tube with 1-1/2" power tube
(the slips hold production tube only)
Nom. Tubing Size to Hold with Power Tube
2-1/2" x 1-1/4"
3" x 1-1/2"
API Tubing Size to Hold with Power Tube
2-7/8" x 1.660"
3-1/2" x 1.900"
228
7502-65-A
219
7502-65-B
Wt. Per Set Complete lbs.
Part Number Complete
2" x 1-1/4"
2-1/2" x 1-1/4"
3" x 1-1/4"
2-3/8" x 1.660"
2-7/8" x 1.660"
3-1/2" x 1.660"
218
7502-67-A
220
7502-67-B
225
7502-67-C
To order — Specify: (1) Spider Open End. (2) Part numbers.
(3) Size of body or bowl (3-1/2" or 4-1/2"). (4) If single or double
strings.
AIR HOSE
COMPLETE
Power Tubing Spiders
WEB WILSON® Model PM Power Tubing Spiders
These power spiders are available to handle the following
tubing sizes: 1.315", 1.660", 1.900", 2", 2-1/16", 2-3/8", 2-7/8",
and 3-1/2". Only two sizes of slips (bodies) are required for
handling tubing up to 3-1/2" O.D.
One size slip will handle tubing from 1.315" O.D. to 2-7/8"
O.D. equipping with proper size insert. The other size slip handles 3-1/2" O.D. using the 3-1/2" insert.
Two spider types are available: hydraulic and pneumatic.
Both are rated 50-ton maximum capacity. Pneumatic spiders
operate on air pressure from 40 to 50 psi. Hydraulic powered
spiders operate on maximum recommended working pressure
of 150 psi.
A hinged door permits installation without “stripping” over the
tubing. Slip inserts are easily changed from one size to another; interchangeable inserts permit the assembly to work for
many tubing sizes.
The slip inserts are carefully machined from steel alloy.
To order — Specify: (1) Tubing Spider, Power. (2) Part number.
(3) Hydraulic or pneumatic. (4) Tubing size. (5) Optional equipment.
Baash-Ross and Web Wilson are licensed trademarks of National Oilwell Varco, L.P.
FOOT VALVE ASSY.
FRONT VIEW OF SPIDER
WITH GUARD ASSY.
AIR SUPPLY HOSE
COMPLETE
TABLE NO. 3
WEB WILSON Model “PM” Power tubing Spider
50-Ton Capacity
Part
Number
Wt.,
Lbs.
Each
Air Operated Spider Complete w/Control Assembly
and Hoses w/Slip Bodies to Hold:
1.315"–2-7/8" O.D. (Less Inser ts)
3-1/2" O.D. (Less Inser ts)
8529-5095
8529-5097
251
251
Hydraulically Operated Spider Complete w/Control
Assembly and Hoses w/Slip Bodies to Hold:
1.315"–2-7/8" O.D. (Less Inser ts)
3-1/2" O.D. (Less Inser ts)
8529-5096
8529-5098
259
259
Description
9
POWER TONGS
2853 Cherry Avenue
Signal Hill, CA 90755
Ph: (562) 424-8564
Fax: (562) 595-6174
OIL WELL TOOLS
RS HYDRAULIC TUBING TONG
Description:
The Model RS is a gate-type tong that
incorporates a four way control valve to
reverse the tong without roll-over.
This reversible model does not include a
positioner and uses stiff arm installation.
As an option, the Model RS is available
with positioner and a roll-over hanger.
Operational features:
Can deliver and maintain 12 HP (8.95 kw)
continuously when required without overload or strain. The control valve can be
operated from either front or rear control
levers. The heavy-duty transmission handles high torque without overload or
strain. Quick change jaw and bushing
assemblies accommodate curved face
dies as well as straight dies. Choice of
standard or high-torque motor.
Size range:
1.050"-4-1/2" (26,7-114,3 mm)
BTS REVERSIBLE SHORT LEVER,
GATE TYPE HYDRAULIC
POWER TONG
Description:
The BTS combines the greater horsepower speed and torque of other
Cavins/BJ power tubing tongs. In addition, the model BTS has special spacesaving qualities for smaller rigs used for
slim hole production and workover jobs.
The overall saving in length totals 10"
(254 mm).
Size range:
1.050" to 4-1/2" (26,7-114,3 mm)
RS Tubing Tong
®
HYDRATORC POWER TUBING TONGS
These part numbers are for power tongs complete less jaws and bushings, less
hoses and quick-connect couplings.
Model
Rigid Hanger Less Positioner
Weight Ea.
Part no.
lbs
kg
Roll-over Hanger with Positioner
Weight Ea.
Part no.
lbs
kg
RS
BTS
CTS
34891
30072
35089
34892
30072-2
35090
580
650
580
263
295
263
590
659
590
268
299
268
These part numbers are for power tongs complete with high-torque duty motor
less jaws and bushings, less hoses and quick-connect couplings.
RS
BTS
CTS
34891-1
30072-12
35089-1
580
650
580
263
295
263
34892-1
30072-11
35090-1
590
659
590
268
299
268
SUPER-POWAIRMATIC® POWER TONGS
These part numbers are for power tongs complete less jaw and bushing, less
hoses and quick-connect couplings.
SA
BTA
27550-2
30580-2
572
652
259
266
27550
30580
575
655
261
297
Hydratorc and Super-Powairmatic are licensed trademarks of National Oilwell Varco, L.P.
10
CTS REVERSIBLE, STANDARD LENGTH
GATE-TYPE TUBING AND CASING TONG
Description:
Similar to the Model RS except that the front end
has been modified to handle pipe from 2-3/8" tubing to 5-1/2" casing. Quick-change jaws and bushing assemblies take either curved or straight dies.
Size range: 2-3/8" to 5-1/2" (60,3-139,7 mm)
Specifications RS, BTS, CTS Tongs:
Torque in Hi Gear, ft-lb
@ 2000 psi
(140 bar)
Torque in Lo Gear, ft-lb
@ 2000 psi
(140 bar)
Speed in Hi Gear, RPM @
30 GPM
(113.6 I/min)
Speed in Lo Gear, RPM @
13 GPM
(49.2 I/min)
Standard Motor
High Torque Motor
1200 ft-lb
(1627 Nm)
1700 ft-lb
(2305 Nm)
4650 ft-lb
(6305 Nm)
6650 ft-lb
(9017 Nm)
83 RPM
68 RPM
21 RPM
18 RPM
SA REVERSIBLE, STANDARD-LENGTH,
GATE-TYPE, AIR POWERED TONG
Description:
High-Torque vane-type 9 HP (6,7 kw) air motor.
Fully enclosed heavy-duty transmission handles
high torque without overload or strain. Positive
front-end chain drive. Four way valve and manifold
provide reverse without roll-over. Also available as
BTA Model, retaining the same features as the SA
but having a 10" (254 mm) shorter length.
Size range: 1.050" to 4-1/2" (26,7-114,3 mm)
Specifications SA, BTA:
Maximum Torque in Hi Gear. ft-lb @
150 psi (10.34 bar)
Maximum Torque in Lo Gear, ft-lb @
150 psi (10.34 bar)
Speed in Hi Gear, RPM
Speed in Lo Gear, RPM
1660 ft-lb (2250 Nm)
6500 ft-lb (8814 Nm)
90 RPM
24 RPM
Model CH (not shown)
Closed head hydraulic powered tong with
reversible motor
Design Features: Jaws turn over to reverse tong.
Choice of standard or High Torque motor to provide desired torque. Five multiple-size-range jaws
are designed with convex die contact surfaces for
positive even pressure grip equally spaced around
the tubing circumference.
Operational Features: A tandem control valve
controls both tong operation and lift cylinder.
Balanced spring suspension for easy handling and
positioning. Torque valve adjusts tong torque to
tubing joint requirements.
Optional Equipment: Closed-Head Back-up;
Operator can choose either of two positions. He
can straddle couplings and make up both threads
on API tubing when going into hole or he can move
back-up closer to tong when gripping coupling.
Gripping system identical to Model CH tong but is
operated manually.
HOW TO ORDER TONGS COMPLETE
33135-7 “CH” Tong Complete with 2-3/8–3-1/2"
Jaw and Jaw Holder Assembly
33135-16“ CH” Tong Complete with 2-3/8"–3-1/2"
Jaw and Jaw Holder Assembly and High
Torque Motor
2853 Cherry Avenue
Signal Hill, CA 90755
Ph: (562) 424-8564
Fax: (562) 595-6174
OPTIONAL EQUIPMENT
FOR POWER TUBING TONGS
OIL WELL TOOLS
JAW AND BUSHING ASSEMBLIES–Hydratorc® Power Tongs
Models RS and BTS and Super-Powairmatic® Models SA and BTA
Pipe size
In.
mm
1.050
26.67
1.050
26.67
1.135
33.40
1.315
33.40
1.660
42.16
1.660
42.16
1.750
44.45
1.750
44.45
1.900
48.26
1.900
48.26
2 & 2-1/16 50.8 & 52.39
2 & 2-1/16 50.8 & 52.39
2-3/8
60.33
2-3/8
60.33
2-7/8
73.03
2-7/8
73.03
3-1/2
88.9
3-1/2
88.9
4
101.6
4
101.6
4-1/2
114.3
4-1/2
114.3
Assembly
Type
Part
No.
Curved
Face Die
Jaw
Bushing
Jaw
Bushing
Jaw
Bushing
Jaw
Bushing
Jaw
Bushing
Jaw
Bushing
Jaw
Bushing
Jaw
Bushing
Jaw
Bushing
Jaw
Bushing
Jaw
Bushing
23446-1
23447-1
29373-1
29374-1
29310-1
29307-1
29802-1
29801-1
29309-1
29306-1
29308-1
29305-1
27477-1
27645-1
27481-1
27660-1
17912-1
17913-1
23624-1
23623-1
24553-1
24552-1
Straight
Die
6472
6472
6473
6473
29313
29313
29313
29313
29312
29312
29311
29311
27494-1
27494-1
27498-1
27498-1
6473
6473
6473
6473
24554
24554
Weight Ea.
lb-oz
kg
6–0
12–0
6–0
12–0
5–12
11–8
5–9
11–5
5–4
11–0
5–0
10–2
4–12
10–8
4–8
10–8
4–8
9–12
4–0
8–0
3–0
5–0
2.72
5.44
2.27
5.44
2.61
5.22
2.52
5.13
2.38
4.99
2.27
4.59
2.15
4.76
4.76
4.76
2.04
4.42
1.81
3.63
1.36
2.27
ON-OFF DEVICE FOR GATE-TYPE POWER TONGS
This air-operated tool increases tubing handling efficiency by
moving gate-type Hydratorc or Super-Powairmatic power tongs
onto or off the tubing automatically. Utilizes regular rig air source.
Power On-Off Device Complete with Standard Hand Control –
Part No. 29637-1 (Part No. 30237-Optional Foot Control).
SEMI-AUTOMATIC POSITIONER FOR GATE-TYPE
POWER TONGS
This optional feature consists of a control valve to line up the
opening accurately and quickly. The Semi-Automatic Positioner
can be included in any Hydratorc or Super-Powairmatic gatetype power tong.
®
For Hydratorc Power Tongs
2
2
Part Name
Part
Number
Weight
Lbs.
1" x 15' Hydraulic Hose
1" Coupling
991010-180
942029-16
18
4
FOR SUPER-POWAIRMATIC TONGS
Number
Required
Part Name
Part
Number
Weight
Lbs.
1
1
3/4" x 50' Air Hose Assembly
1" x 50' Air Hose Assembly
950123-3802
950124-3803
34
43
CLOSED HEAD “CH” TONG
Part No. 60210
Part No. 60250
Hydraulic Lift Assembly
Stiff Arm Assembly
BACK-UP ATTACHMENT FOR CLOSED-HEAD “CH”
POWER TONG ONLY
COMPONENTS
NO.
1-5/16–
Req’d 2-1/16
2-3/8–
3-1/2
3-1/16–
4
4–
4-3/4
5–
6-1/16
Back-Up Assy.
Back-Up Jaw Assy.
Back-Up Jaw
1
5
5
32947
33707
—
32947
33708
—
33647
—
33655
33647
—
33056
32947
33706
—
T-head latch with 3-jaw design and 2-step and 3-step lug jaw
construction to assure close grip on both coupling and tool
joint without adjustment.
HOW TO ORDER TONG COMPLETE
30430-110 “MS” Back-Up Attachment Complete with 2-3/8"
3.668 Lug Jaw Assembly
Part
No.
30430
31134
Weight
(lbs.–oz.)
Part Name
Back-Up Attachment Complete, Less Lug Jaw
(1.900"–2-1/16" & 2-3/8"–4-1/2")
Back-Up Attachment Complete, Less Lug Jaw
(4-1/2"–6-1/8")
47–0
53–14
REPLACEMENT PARTS – “MS” BACK-UP ATTACHMENT
HOSES AND QUICK-CONNECT COUPLINGS
Number
Required
BACK-UP TONGS FOR GATE-TYPE POWER TONGS
Design Features: Cavins/BJ Type MS back-up tongs have
Number
Required
Part No.
1
1
1
1
1
1
1
1
1 (2*)
2 (3*)
4 (5*)
1
34314-1
30422-6
30424-6
33917-6
31139-6
6267
31130
31135
5206
13494
939672-18
28622-5
1
1
2
1
1
1
1
1
2
1
2
1
2
28622
28623
945031-64
30591
28624
30572-1
30573
30574
30575
30421-1
30359
30359-1
6209
Part Weight
Name
1.900"–2-1/16" Lug Jaw Assembly**
2-3/8"–3.668" Lug Jaw Assembly**
3-1/2"–4-1/2" Lug Jaw Assembly**
4-1/2"–5-1/4" Lug Jaw Assembly**
5.200"–6-1/8" Lug Jaw Assembly**
1.900"–4-1/2" Short Jaw
4-1/2"–6-1/8" Short Jaw
4-1/2"–6-1/8" Latch Jaw
1.900"–4-1/2" Latch Spring
1.900"–4-1/2" Hinge Pin
1.900"–4-1/2" Cotter Pin
Outer-Inner Sleeve Assembly
(1.900"–6-1/8")
Outer Sleeve
Inner Sleeve
Suspension Spring
Leveling Screw
Lever
Latch
Long Jaw Spring
Short Jaw Spring
Lever Hinge Pin
Long Jaw Assembly**
Toggle Pin (Long) w/Chain
Toggle Pin (Short) w/Chain
Tong Die
(lbs.–oz.)
—
6—0
7—14
—
4—8
2—0
2—0
2—0
0—2
0—6
0—1
23—0
13—0
10—0
0—4
0—3
8—0
1—8
0—2
0—2
0—7
12—0
1—0
0—8
0—3
*No. Req’d for 4-1/2"–6-1/8" Range **Each Assy. Includes Lug Jaw & 6209 Die
Hydratorc and Super-Powairmatic are licensed trademarks of National Oilwell Varco, L.P.
11
2853 Cherry Avenue
Signal Hill, CA 90755
Ph: (562) 424-8564
Fax: (562) 595-6174
POWER TONGS
OIL WELL TOOLS
CH-8000
The Cavins/BJ CH-8000 is designed for
fast and uniform make-up and break-out
of tubular connections on production,
workover jobs and during slimhole
drilling operations. This double motor,
chain-driven tong, has no gear transmission and clutches. The CH-8000 features five multi-range jaw assemblies to
handle all tubing and coupling sizes
from 1-5/16" through 6-1/16" O.D. This
compact and powerful closed-head
power tubing tong, offers in this design a
combination of Cavins/BJ’s past experience with today’s technology. The extensive CH-8000 field testing done to date
has shown that the elimination of gear
train, clutches and the oil lubrication
front end have drastically reduced the
amount of maintenance which is
required on other types of previously
designed power tongs. After 15 continuous months of operation 12 hours per
day, 6 days per week, this tong experienced no downtime.
Features:
Shift on the fly capability. Separate
speed and torque motors allow the tong
to be shifted in/out of high torque mode
easily and smoothly. No more need to
overhaul or replace transmissions. Low
maintenance and high reliability. Routine
maintenance is limited to 15 minutes per
week for lubrication. No oil bath to leak.
Jaw reversal is an easy 5 minutes. A
unique hinged top cover provides
access to the jaws so they can be
reversed for going back into the hole.
GT-8000
The 8000 Series tubing tong family
has been extended to include the
Gate Type Tong, which incorporates
many of the features of the CH-8000
in its small compact frame. This new
hydraulic tong is the Cavins/BJ GT8000.
Features:
Incorporates the same simple motor
hydraulic drive circuit as utilized in
the CH-8000. Reversible clamping
system eliminates roll-over which
occurs in other competitive tools.
Safety door prevents rotation when
door is open. The brake band is easily adjustable from outside of the
tong. Sealed bearings eliminate the
use of cam rollers and reduce maintenance. The hydraulic drive system
is mounted on a detachable frame for
simplified maintenance. The make-up
torque can be pre-set by adjusting a
built-in pressure relief valve which
prevents tubular damage.
Assembly number:
GT-8000
:202100-1
Manual Back-up :200880-S
Size
Inch
Size
mm
Brake ring
Assembly
Tong Jaw &
Back-up Jaw
Assembly (5) Req’d
Guide
Ring
1-5/16–1.900
1-7/8–2-3/8
2-3/8–2-7/8
2-7/8–3-1/2
3-1/2–4-1/2
4–4-3/4
5–6-1/16
33-48
48-60
60-73
73-89
89-114
102-121
127-154
250049
200049
250049
250049
250136
250136
250136
50-149-6-100
58-330-100
50-22-7-100
50-22-8-100
58-509-100
58-509-101
58-314
200395-1
200395-2
200395-2
200395-2
200395-3
200395-3
200395-4
JAW AND BUSHING ASSEMBLIES GT-8000
SPECIFICATIONS
12
GT-8000
JAW ASSEMBLIES CH-8000
Assembly numbers:
CH-8000 Hi-speed : 250100
CH-8000 Hi-torque : 250100-1
Hydr. lift cylinder
: 60210
Manual back-up
: 250111
Hydr. back-up
: 250111-1
Size range
33-154 mm
Torque in Hi gear
@ 2500 psi
175 Bar
Torque in Lo gear
@2500 psi
175 Bar
Speed in Hi gear
@ 35 G.P.M. 132.5 L/min
Speed in Lo gear
@ 35 P.P.M. 132.5 L/min
CH-8000
CH-8000
Hi Speed
GT-8000
Hi Torque
1-5/16"-6-1/16"
33-154 mm
1-5/16"-6-1/16"
33-154 mm
1-5/16"-5-1/2"
33-140 mm
1100 ft-lbs
1492 Nm
1675 ft-lbs
2271 Nm
2150 ft-lbs
2915 Nm
6250 ft-lbs
8474 Nm
8500 ft-lbs
11525 Nm
8500 ft-lbs
11525 Nm
140 R.P.M
103 R.P.M.
100 R.P.M.
32 R.P.M.
25 R.P.M.
25 R.P.M.
Size
Inch
Size
mm
Jaw Assembly
(2) required
Back-up
Bushing
8500-5565 Die
No. Req’d/Size
1.500"
1.660"
1.900"
2-1/16"
2-3/8"
2-7/8"
3-1/2"
4"
4-1/8"
4-1/2"
4-3/4"
5"
5-1/2"
38
42
48
51
60
73
89
102
104
114
120
127
140
201022-1
201023-1
201024-1
201025-1
8519-5055
8519-5054
8519-5053
201031-1
8519-5052
8519-5051
8519-5050
8519-5049
8519-5048
201010-1
201011-1
201012-1
201013-1
201014-1
201015-1
201016-1
201009-1
201017-1
201018-1
201019-1
201020-1
201021-1
4
4
4
4
6
6
8
8
8
10
10
10
10
2853 Cherry Avenue
Signal Hill, CA 90755
Ph: (562) 424-8564
Fax: (562) 595-6174
HILLMAN-KELLEY®
Power Tongs
OIL WELL TOOLS
HILLMAN-KELLEY® Model 3700-H Standard Power Tong
Specifications
Over-all length – 42"; length from center of pipe to back-up eye – 29"
Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 560 lbs.
Hydraulic power supply required:
36 gpm @ 1000 psi
15 gpm (minimum) @ 2000 psi
Tong speeds . . . . . . . . . . . . . . . . . . . . . . . . High gear – 110 rpm
Low gear – 30 rpm
Maximum tong torque (working) . . . . . . . . . . . . . . . . . 6000 ft. lbs.
Size range . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.050" – 4.5" O.D.
8504-5000
Model 3700-H Power Tong
HILLMAN-KELLEY® Model 4600-H Deluxe Power Tong
Specifications
Over-all length – 42"; length from center of pipe to back-up eye – 29"
Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 585 lbs.
Hydraulic power supply required:
35 gpm @ 1000 psi
15 gpm (minimum) @ 2000 psi
Tong speeds . . . . . . . . . . . . . . . . . . . . . . . . High gear – 110 rpm
Low gear – 30 rpm
Maximum tong torque (working) . . . . . . . . . . . . . . . . . 6000 ft. lbs.
Size range . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.050" – 4.5" O.D.
8505-5000
Model 4600-H Power Tong
HILLMAN-KELLEY® Model 5500-H Power Tong
Specifications
Over-all length – 42"; width – 29"; length from center of pipe to
back-up eye – 29"
Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 585 lbs.
Hydraulic power supply required:
35 gpm @ 1000 psi
15 gpm (minimum) @ 2000 psi
Tong Speeds . . . . . . . . . . . . . . . . . . . . . . . . . High gear – 95 rpm
Low gear – 30 rpm
Maximum tong torque (working) . . . . . . . . . . . . . . . . . 7000 ft. lbs.
Size range . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.050" – 5.5" O.D.
8509-5000
Model 5500-H Power Tong
HILLMAN-KELLEY® Model 500 C
8502-5344
Model 500-C Hydraulically Powered Tong
Dies with full circle
contact for running tubing.
Jaws used when running
sucker rods.
Hillman-Kelley is a licensed trademark of National Oilwell Varco, L.P.
For Tubing and Sucker Rods
Runs single or multiple tubing strings and sucker rods Tubing
jaws for 3/4" (1.050" O.D.) through 3" (3-1/2" O.D.) tubing; Rod
jaws for 5/8" through 1-1/8".
Eliminates need to change tongs from tubing to rod…just change
the jaws.
Compact, lightweight, powerful – weights only 400 pounds.
Efficiently powers in either direction; no need to turn over to
makeup or breakout.
Quick switch from makeup to breakout accomplished in seconds.
Easy to operate from front, sides, or rear.
Uses proven planetary gear box with hydraulic motor.
Has a low gear capable of breaking any sucker rod joint.
Works smoothly with an automatic retractor.
Dual strings can be run from rig floor.
Specifications
Over-all dimensions: length – 35"; width – 16"; (12" when equipped
for multiple-string operation); height – 25"; length from center of
pipe to back-up eye – 29"
Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400 lbs.
Hydraulic power supply required:
35 gallons per minute @ 1000 psi
10 gallons per minute (minimum) @ 2000 psi
Tong Speeds . . . . . . . . . . . . . . . . . . . . . . . . . high gear – 98 rpm
low gear – 25 rpm
Maximum torque high gear. . . . . . . . . . . . . . . . . . . . . 1150 ft. lbs.
Maximum torque low gear . . . . . . . . . . . . . . . . . . . . . 4000 ft. lbs.
*To order–Specify: 1. Tong Model. 2. Part numbers. 3. Pipe O.D.
4. With or without hanger. 5. With or without Back-up.
13
POWER TONGS
OIL WELL TOOLS
Model 74-92-R
Tubing
Jaw Sizes Available
1" through 3-1/2" O.D. 100 to 2,500 Ft. Lbs. Torque
Torque range high gear . . . . . . . . . . . . . . . . . . . 100 to 800 ft. lbs.
Max. torque low gear. . . . . . . . . . . . . . . . . . . . . . . . . 2,500 ft. lbs.
RPM high . . . . . . . . . . . 110*
RPM low . . . . . . . . . . . . 30*
*(RPM based on published requirements of motor manufacturers
21 GPM to tong motor)
Length (A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45"
Space requirement on Pipe (B). . . . . . . . . . . . . . . . . . . . . . 6-3/8"
with Backup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-3/8"
Max. elevator Dia. (C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30"
C.L. of pipe to C.L. of Anchor (D) . . . . . . . . . . . . . . . . . . . 30-3/4"
Weight approx. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 550 lbs.
Torque reactive force at anchor pin . . . . . . . . . . . . . . . . 1,070 lbs.
Model 58-93-R
Tubing & Casing
Jaw Sizes Available
1-5/16" through 7" O.D. 300 to 6,000 Ft. Lbs. Torque
Torque range high gear . . . . . . . . . . . . . . . . . 300 to 1,300 ft. lbs.
Max. torque low gear. . . . . . . . . . . . . . . . . . . . . . . . . 6,000 ft. lbs.
RPM high . . . . . . . . . . . 126*
RPM low . . . . . . . . . . . . 27*
*(RPM based on published requirements of motor manufacturers
33.5 GPM to tong motor)
Length (A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51"
Space requirement on Pipe (B). . . . . . . . . . . . . . . . . . . . . . 9-1/2"
with Backup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-1/2"
Max. elevator Dia. (C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30"
C.L. of pipe to C.L. of Anchor (D) . . . . . . . . . . . . . . . . . . . . . . 30"
Weight approx. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1,000 lbs.
Torque reactive force at anchor pin . . . . . . . . . . . . . . . . 2,051 lbs.
Model 54-93
Light Drill Pipe, Casing, Tubing
Jaw Sizes Available
1-5/16" through 7" O.D. 300 to 12,000 Ft. Lbs. Torque
Torque range high gear . . . . . . . . . . . . . . . . . 300 to 1,500 ft. lbs.
Max. torque low gear. . . . . . . . . . . . . . . . . . . . . . . . 12,000 ft. lbs.
RPM high . . . . . . . . . . . 130*
RPM low . . . . . . . . . . . . 19*
*(RPM based on published requirements of motor manufacturers
39 GPM to tong motor)
Length (A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61"
Space requirement on Pipe (B). . . . . . . . . . . . . . . . . . . . . . 9-1/2"
with Backup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18"
Max. elevator Dia. (C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40"
C.L. of pipe to C.L. of Anchor (D) . . . . . . . . . . . . . . . . . . . 43-5/8"
Weight approx. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1,360 lbs.
Torque reactive force at anchor pin . . . . . . . . . . . . . . . . 3,255 lbs.
Model 54-02
Light Drill Pipe, Casing, Tubing
Jaw Sizes Available
2-3/8" through 4-1/4" Tool Joints
2-3/8" Tubing through 10-3/4 Casing
300 to 18,000 Ft. Lbs. Torque
Torque range high gear . . . . . . . . . . . . . . . . . 300 to 1,500 ft. lbs.
Max. torque low gear. . . . . . . . . . . . . . . . . . . . . . . . 18,000 ft. lbs.
RPM high . . . . . . . . . . . . 80*
RPM low . . . . . . . . . . . . 14*
*(RPM based on published requirements of motor manufacturers
55.5 GPM to tong motor)
Length (A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76"
Space requirement on Pipe (B). . . . . . . . . . . . . . . . . . . . . . 9-1/2"
with Backup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20"
Max. elevator Dia. (C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40"
C.L. of pipe to C.L. of Anchor (D) . . . . . . . . . . . . . . . . . . . 47-5/8"
Weight approx. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1,600 lbs.
Torque reactive force at anchor pin . . . . . . . . . . . . . . . . 4,656 lbs.
Foster is a licensed trademark of National Oilwell Varco, L.P.
14
2853 Cherry Avenue
Signal Hill, CA 90755
Ph: (562) 424-8564
Fax: (562) 595-6174
2853 Cherry Avenue
Signal Hill, CA 90755
Ph: (562) 424-8564
Fax: (562) 595-6174
POWER SUCKER ROD TONGS
OIL WELL TOOLS
MARK II THROUGH MARK VI
POWER SUCKER ROD TONGS
Description:
Purpose: Applies correct, uniform
torque, reducing costly rod failures
that often occur with hand wrenching.
Special features: The possibility
of cross-threading is reduced to a
minimum. Fully throttle operated.
Torque gauge is standard equipment. Easily converted for macaroni tubing. Choice of air or
hydraulic power.
The Cavins/BJ power rod tong
delivers ample power to make up
and break out all rod sizes. A single
unitized jaw assembly fits 5/8", 3/4"
and 7/8" (15.88 mm, 19.05 mm, and
22.23 mm) rods without change;
allows fast, unitized jaw change for
1/2" and 1", 7/8" (12.7 mm and
25.4, 22, 23 mm) rod with 1-1/8"
square and 1-1/8" (25.58 mm) rod
sizes. The rod tong is also easily
converted for macaroni tubing by
replacing the rotating jaw assembly
with macaroni tubing jaws.
Power Sucker Rod Tong
HOW TO SPECIFY AND ORDER
HYDRAULIC REQUIREMENTS
TONG LESS INNER RING
ASSEMBLIES AND
BACK UP WRENCHES
Part
Number
Maximum
Torque
Maximum
Speed
0—1,000
psi
1,000—2,000
psi
Mark II (Hydraulic Motor)
27841
1,180 ft./lbs.
Mark IV (Hydraulic Motor)
27841-1
1,370 ft./lbs.
140 rpm
30 gpm
13 gpm
120 rpm
30 gpm
13 gpm
Mark V (Hydraulic Motor)
27841-5
1,850 ft./lbs.
90 rpm
30 gpm
13 gpm
AIR PRESSURE REQUIREMENT
Mark III (Air Motor)
27339
1,180 ft./lbs.
120 rpm
120 psi Maximum
Mark VI (Air Motor)
27841-6
1,850 ft./lbs.
89 rpm
120 psi Maximum
INNER RING ASSEMBLIES AND BACK-UP WRENCHES
Size of Rod
Rod Inner Ring
1/2"
5/8"
27899-2
3/4", 7/8"
27899
27903
1-1/8"
7/8" Rod with 1-1/8" Square
27899-1
27899-3
Rod Back-Up Wrench
27898
27906
27907
27903-1
Size of Macaroni Tubing
1.050"
1.315"
1.660"
1.900"
........
Tubing Inner Ring
30718
30716
30714
30712
........
Finger Saver
27902
1"
27899-4
27894-10
Safety Tool
27899-W
Model 76 Sucker Rod Tong
Jaw Sizes Available
1/2", 5/8", 3/4", 7/8", 1", 1-1/8" Sucker Rods
100 to 2,500 Ft. Lbs. Torque
Torque range high gear . . . . . . . . . . . . . . . . . . . to 850 ft. lbs.
Max. torque low gear . . . . . . . . . . . . . . . . . . . . . 2,500 ft. lbs.
RPM high . . . . . . . . . . . 95
RPM low . . . . . . . . . . 23
Hydraulic requirement . . . . . . . . . . . . . . . 25 GPM. 2,000 PSI
Length (A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42"
Space req. on rod (B). . . . . . . . . . . . . . . . . . 10" with Backup
C.L. of Pipe to C.L. of Anchor (D) . . . . . . . . . . . . . . . . 32-1/2"
Weight approx. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400 lbs.
Torque reactive force at anchor pin . . . . . . . . . . . . . . 873 lbs.
Foster is a licensed trademark of National Oilwell Varco, L.P.
15
2853 Cherry Avenue
Signal Hill, CA 90755
Ph: (562) 424-8564
Fax: (562) 595-6174
MANUAL TONGS
OIL WELL TOOLS
KELCO® FULGRIP® Tubing Tongs
The “wrap-around” design gives a 360° grip on the tubing
with 88% to 95% of the circumference area in die contact. As
a result there is little possibility the pipe will be scored or
crushed during making or breaking the string.
FULGRIP Tongs are lightweight, easy to transport and use.
Their sturdy design and tough construction tend to deliver
dependable, long-lasting service.
These tubing tongs are available in four types:
Type A-20 – lightweight, aluminum tong for macaroni tubing
1.050"-2.063" O.D. and plastic tubing 1.050"-2.500" O.D.
Type K-20 – high grade steel tongs for rugged, dependable
field service for tubing 1.050"-2.500" O.D., 1,500 Ft.-Lb.
torque rating.
Type K-25 – high grade steel tongs for tubing 1.200"-3.063"
O.D., 2,000 Ft.-Lb. torque rating.
Type K-30 – for heavy-duty service for tubing 2.062"-4.125"
O.D., 5,000 Ft.-Lb. torque rating. This tong is available with
either standard hanger (K-30A) or with rollover block (K30B).
FIG. 1 – Type A-20 Tubing Tong
TABLE NO. 1
Type
Size Range
Part Number (Less Dies)
A-20
K-25
K-30
K-30A
K-30B
1.050” – 2.063” (26.7mm – 52.4mm)
1.200” – 3.063” (30.5mm – 77.8mm)
2.062” – 4.125” (52.4mm – 104.8mm)
2.062” – 4.125” (52.4mm – 104.8mm)
2.062” – 4.125” (52.4mm – 104.8mm)
8527-5002
8527-5016
8527-5035
8527-5036
8527-5037
FIG. 2 – Tong Pull-Back Strap
TABLE NO. 1
Tong Pull-Back Strap
Item
No. Req’d.
Part Number
Wt., Lbs. Each
Pull-Back Strap
1
24747
3
SNAP-ON TUBING TONG
Purpose: Strong, quick-acting tubing tong made of high-quality, heat-treated steel.
Description: This easily handled tong is “snapped on” with
one hand, locking automatically around the tubing. It can be
released only by the operator. The tong is held open when off
the tubing, or in a closed position around the pipe, by two
spring plungers which act directly against the body and lever.
The BJ tong die is held at the proper angle for taking an
instant, positive grip, releasing readily when the operator
ratchets the tong. This firm, non-slip grip permits unscrewing
joints of tubing up to 3-1/2" diameter without crimping.
DESCRIPTION OF SNAP-ON TONG MODELS
Order by Tong Description and Part Number
Tong Model
Snap-On Tong Complete, with Back-up for 2-3/8" O.D.
API Tubing
Snap-On Tong Complete, with Back-up for 1.90" API
Upset Tubing Coupling
Snap-On Tong Complete, with Back-up for 2-7/8" O.D. API
Tubing and 2-3/8" API Plain Tubing Coupling
Snap-On Tong Complete, with Back-up for 2-3/8" O.D. API
Upset Tubing Coupling
Snap-On Tong Complete, with Back-up for 3-1/2" O.D. API
Tubing and 2-7/8" API Plain Tubing Coupling
Snap-On Tong Complete, with Back-up for 2-7/8" API
Upset Tubing Coupling
Part Number
36816-237
36816-250
36816-287
36816-306
36816-350
36816-366
DESCRIPTION OF SNAP-ON JAW ASSEMBLIES
Assembly
Part Number
2-7/8" API Upset Coupling Jaw Assembly
2-3/8" API Tubing Jaw Assembly
2-7/8" API Tubing and 2-3/8" API Plain Coupling Jaw Assembly
3-1/2" API Tubing and 2-7/8" API Plain Coupling Jaw Assembly
1.90" API Upset Coupling Jaw Assembly
2-3/8" API Upset Coupling Jaw Assembly
37046-3
37044-2
37042-2
37046-2
37044-3
37042-3
TYPE
“MS” TONG
Purpose: Light drilling and
tubing work, including seismograph, shot-hole and
exploration drilling.
Description: The Type MS
has proved its efficiency in
the field on all types of slimhole drilling rigs. It has a Thead latch which, with the
2-step and 3-step lug jaw
construction enables the
tong to fit both pipe coupling and tool joint without any adjustment. The 3-jaw design
permits uniform contact around the circumference of the pipe.
The tong is strong enough to easily break both tool joints and
bits in light drilling operations.
A rigid hanger suspension device allows fast, permanent
adjustment, holding the tong balanced and ready for use. The
Type MS is equipped with the same roll-over hanger feature
found on the Type WS. All parts are interchangeable except
the long jaw, latch, and lug jaws. The changes are slight
dimensionally, but greater performance can be expected.
Size Range: 1.900" through 6-1/8" O.D.
Torque Ratings: 6,500 ft. lbs. from 1.900" through 6-1/8" O.D.
TO ORDER TONG COMPLETE
30425-110 “MS” Tong Complete with 2-3/8"–3.668" Lug Jaw Assembly
SPECIFICATIONS
Order by Part Number, Part Name and Size
Part
Req’d.
Part Number
30425
31131
“MS” TONG COMPLETE LESS LUG JAWS (1.900"–4-1/2")
“MS” TONG COMPLETE LESS LUG JAWS (4-1/2"–6-1/8")
Kelco, Fulgrip and Snap-on are licensed trademarks of National Oilwell Varco, L.P.
16
Wt.
Lbs.—Oz.
43
44
2853 Cherry Avenue
Signal Hill, CA 90755
Ph: (562) 424-8564
Fax: (562) 595-6174
SUCKER ROD & TUBING
ELEVATORS
OIL WELL TOOLS
TYPE ‘TA’ CENTER LATCH ELEVATORS
Purpose: Center-latch elevators of superior design
for handling collar-type drill pipe, casing and tubing.
Description: All TA elevators are constructed in two
halves of practically the same weight, providing
proper balance and easier opening and closing.
Special Features: Proper balance for easier handling; latch and safety latch lock combinations; other
operator safety features
Safety features include guarded operating handles to help prevent accidents to operators and an
extra handle at the rear of the elevators for easier,
safer operation. All TA elevators are equipped with a
latch and safety latch lock combination.
TA Elevator
“TA” SERIES COLLAR TYPE CENTER LATCH ELEVATORS A SERIES
Size
Inches
mm
1.050—2-7/8
1.660—2-7/8
3-1/2—4-1/2
2-3/8—2-7/8
3-1/2—5
27—73
42—73
80—114
60—73
89—127
Type
Frame NR.
Cap.
Tons
Weight
lb-oz
kg
TA
TA
TA
TA
TA
32387–*
32385–*
32386–*
32383–*
32384–*
35
65
65
100
100
39
65
83
100
158
18
29
38
45
72
*Must specify O.D. size and type of tubulars (plain or upset)
D SERIES SIDE DOOR COLLAR TYPE ELEVATORS
‘D’ SERIES
SIDE DOOR ELEVATORS
PURPOSE: Side-door elevators for handling plain or upset Collar-type
drill pipe, casing and tubing. Available in Type LD and LLD model.
Size Ranges and Capacities: API pipe sizes from 2-3/8" (60.33 mm)
through 3-1/2" (88.9 mm) O.D. See the table below.
For Collar-Type Drill Pipe and Tubing – Order by Part Number, Part Name and Size
SPECIFICATIONS–TYPE “LLD” SIDE DOOR ELEVATOR
API Size
In.
mm
Frame
No.l
Elevator Complete
Min. and Max. Dia.
Weldless Links
in.
mm
2-3/8
2-78
31/2
23296—*
23296—*
23296—*
1-3/4—2-1/4
1-3/4—2-1/4
1-3/4—2-1/4
60.33
73.03
88.9
44.45—57.15
44.45—57.15
44.45—57.15
Rated
Capacitiy
tons tonne
Weight Ea.
lb
kg
65
65
65
83
82
80
58.97
58.97
58.97
37.65
37.20
36.29
*Must specify O.D. size and type of tubing (plain or upset)
SPECIFICATIONS–TYPE “LD” SIDE DOOR ELEVATOR
NO-KINK ROD ELEVATORS
PURPOSE: Safe efficient handling of sucker rod sizes from 5/8"
(15.88 mm) through 1-1/8" (28.58
mm). Can also handle hollow type
sucker rod and tubing.
Special Features: Will not bend
or kink sucker rods even under the
heaviest loads.
Reversible-type body.
Capacity: The No-Kink elevator is
available in a heavy type, 43,000pound (19504.8 kg) capacity, for
longer rod strings.
NOTE: When ordering No-Kink
rod elevator for use with hollowtype sucker rods or for handling
tubing, please specify make and
size of rod or tubing.
2-3/8"
2-7/8"
3-1/2"
Body
No.
Min. and Max.
Dia. Weldless
Links
Weight
Lbs.—Oz.
Rated
Cap.
Tons
12591—*
12591—*
12591—*
1-3/4"—2-1/4"
1-3/4"—2-1/4"
1-3/4"—2-1/4"
138—0
136—0
133—0
100
100
100
*Must specify O.D. size and type of tubing (plain or upset)
NO–KINK ROD ELEVATOR–HEAVY TYPE
Elevator Complete
Front Latch
Rod
Size
Part
No.
Wt.
Lbs–Oz.
API Rated
Cap.—Labs.
No.
Req.
Part
No.
Wt.
Lbs.—Oz.
5/8", 3/4"
3/4", 7/8"
1"
1-1/8"
27725
27726
27727
27727-1
28—0
28—0
28—0
28—0
43,000
43,000
43,000
43,000
2
2
2
2
11745
11746
11746-1
11746-2
0—8
0—8
0—8
0—8
REPLACEMENT PARTS–HEAVY TYPE
No.
Req.
Part
No.
Part Name
Wt.
Lbs.—Oz.
1
2
4
2
2
27752
12639
27722
6063
28147
Bail
Rear Latch
Latch Pin
Latch Spring
Bail Retainer Washer
10–8
0—6
0—3
0—2
0—3
17
2853 Cherry Avenue
Signal Hill, CA 90755
Ph: (562) 424-8564
Fax: (562) 595-6174
ROD & CRANE HOOKS
OIL WELL TOOLS
H
DIMENSIONAL DATA
R-35
Spring
R-20
Plain
2-1/2
None
A
B
C
D
E
F
G
H
J
K
L
R
37-5/16
7-7/8
7-3/8
1-7/8
11-1/4
4-5/8
1-13/16
1-1/2
2-1/2
31-11/16
1-7/8
2
25-1/4
6-3/4
6-3/8
1-7/8
4-1/2
4
1-13/16
1-3/8
2-3/8
20-1/4
1-1/2
1-1/2
R-35 Rod Hook
18
…
…
1
1
1
1
1
1
1
1
2
1
1
1
2
2
1
R-20 Hook Complete
R-35 Hook Complete
Body
Bail Housing
Grease Fitting
Shank Spring
Thrust Bearing Assembly
Hex Nut
Pin
Bail Housing Cap
Screw
Latch Handle
Latch Spring
Latch
Pin
Cotter Pin
“O” Ring
Part No.
………
84—0
41—0
27—0
0—1
5—0
4—0
1—0
0—2
2—0
0—2
1—8
0—4
1—0
0—2
………
………
32040
………
32039
32041
940308-1
………
942441-21
32626
947129-28
8222
………
31971
31973
31972
32632
939672-55
942271-43
49—0
……
20—0
20—0
0—1
……
3—0
1—0
0—2
1—12
……
1—8
0—4
1—0
0—2
0—2
0—1
Purpose: Cavins/BJ® crane hooks are offered in two sizes: 10
and 25-ton capacities engineered to Cavins/BJ exacting standards of quality. High-strength steel, properly machined, heat
treated and tested, insures long, trouble-free service.
The locking mechanism on both models is operated by
means of a one-hand grip, protected by a strong loop guard.
The crane hook body can be adapted to most all crane blocks
on special request.
Sizes and Capacities: The Model C-10 has a rated capacity of
10 tons and the Model C-25 has a rating of 25 tons in accordance with API standards.
CRANE HOOKS–REPLACEMENT PARTS
Hook Complete
Body
Bail
Cap
Spring
Nut
O-Ring
Bearing
Cotter Pin
Latch Handle
Latch
Pin
Cotter Pin
Grease Fitting
1
1
1
1
1
1
1
1
1
1
1
2
2
1
32842
32837
32041
8222
31973
32626
942271-43
942441-21
939672-73
31971
32836
32632
939672-55
940308-1
32848
32847
32041
8222
31973
32626
942271-43
942441-21
939672-73
31971
32836
32632
939672-55
940308-1
11
10
13
12
L
………
31982
31965
31966
940308-1
31968
942440-1
32626
947129-28
31967
900042-12
31971
31973
31972
32632
………
………
Part
4
1
Part No.
Model
C-10
5
Model R-20
Weight
Lbs.—Oz.
Model
C-25
3
7
6
8
9
D
Weight
Lbs.—Oz.
No.
Req’d.
F
B
R-35 Rod Hook
C
F
H
J
E
2
R
8
7
6
15
5
3
K
C-10 & C-25
Crane Hooks
Part Name
…
…
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
C
A
R-20 Rod Hook
No.
Req.
2
R
G
Model R-35
Ref.
No.
E
A
Size
Type
Spring
Travel
J
K
Purpose: Sucker rod handling equipment for every depth and
operating condition.
Description: Cavins/BJ® rod hooks are offered in two sizes–20
and 35 ton capacities–engineered to Cavins/BJ’s exacting standards of quality. High-strength steel property machined, heattreated and tested, ensures long, trouble-free service.
The locking mechanism on both models is operated by
means of a one-hand grip at the hook’s center of balance. This
allows the operator to steady the hook, open the locking arm
and engage or remove the bail in one smooth, continuous operation. A strong loop guard protects the operator’s hand.
The Cavins/BJ Model R-35 has a relief spring that provides
2–2-1/2" of travel. It has ample strength to lift a stand of rods,
reducing the possibility of damage to pin and coupling threads.
The Model R-35 Hook also has a large bail as standard equipment.
Sizes and Capacities: The Model R-20 has a rated capacity of
20 tons and the Model R-35 has a rated capacity 35 tons in
accordance with API standards.
REPLACEMENT PARTS–Cavins/BJ ROD HOOKS
13
11
10
1
13
12
G
D
L
B
R-20 Rod Hook
DIMENSIONAL DATA
Model
Reference C-25
Model
C-10
A
B
C
D
E
F
G
H
I
J
K
L
M
6-3/8"
4"
1-3/8"
2-3/8"
7"
27-13/16"
22-7/16"
1-1/2"
2-1/2"
4-1/4"
3"
2-1/4"
9-1/2"
A
B
C
6-3/8"
4"
1-3/8"
2-3/8"
7"
29-9/16"
23-9/16"
1-1/2"
2-1/2"
4-1/4"
3-1/4"
2-1/2"
10-3/4"
D
E
H
F G
I
J
K
L
M
C-10 & C-25
Crane Hooks
2853 Cherry Avenue
Signal Hill, CA 90755
Ph: (562) 424-8564
Fax: (562) 595-6174
ELEVATOR LINKS & HOOKS
OIL WELL TOOLS
TOOLPUSHER LINKS
Description: Toolpusher Links are forged from a single piece of high grade alloy steel
to provide maximum tensile strength. More weight and “plus-diameter” in critical areas
make these Cavins/BJ links extra strong. Short upper eye design means better balance
and easier elevator handling, while reducing wear of the eye section against the swivel
bail or body.
SPECIFICATIONS – TOOLPUSHER LINKS
Part No.*
Size–in.
Size–mm
Rated
Capacity/Set
Tons
37355-1036
37355-1048
37355-1060
37355-1072
37355-1084
37355-1096
37355-1120
1-3/4 x 36
1-3/4 x 48
1-3/4 x 60
1-3/4 x 72
1-3/4 x 84
1-3/4 x 96
1-3/4 x 120
44.45 x 914.4
44.45 x 1219.2
44.45 x 1524.0
44.45 x 1828.8
44.45 x 2133.6
44.45 x 2438.4
44.45 x 3048.0
150
150
150
150
150
150
150
Weight/Set
lb
kg
125
160
190
230
270
310
390
56.7
72.6
86.2
104.3
122.5
140.6
177.3
*Sold only in sets
WEB WILSON®
HYDRA HOOK™
150 Ton
For depth from 5,500 to 8,000 feet using 4-1/2"
drill pipe or 7,000 to 10,000 using 3-1/2" drill pipe.
100 Ton
For depths from 4,500 to 7,000 feet using 3-1/2"
drill pipe.
65 Ton
For depths from 2,750 to 4,500 feet using 3-1/2"
drill pipe and tubing handling.
40 Ton
SHANK
HEAD COVER
“O” RINGS
DUST SEAL
COVER
SWIVEL LOCK RING
SHANK HEAD
For handling of tubing and for drilling to 2,750
feet using 3-1/2" drill pipe.
DUST SEAL
MAIN SPRING
BODY
EQUALIZER RING
SET SCREW
The Web Wilson Hydra Hooks are available in four different capacity ratings from a 40 ton to the 150 ton model.
There are a number of features in each Hydra Hook
designed to add convenience and long life to your rig.
Some of these are:
Hydraulic cushion controls bounce to reduce thread
damage when “jumping out” pipe
Heavy-duty main spring provides extra force to “jump
out” heavy pipe stands
Main roller-type bearing with large contact area always
submerged in oil
Continuous lubrication of main spring and shank
Split ring assembly connects shank to hook
Choice of connections – clevis-to-bail, direct, or unitized
Oil changes easily made with hook hanging from blocks
SPLIT RING
SPRING PILOT
SPRING
PILOT GASKET
BEARING
DRAIN PLUG
SHANK
ASSEMBLY BOLT
(14 THREADS
PER INCH)
USE ONLY FOR
ASSEMBLY OR
DISASSEMBLY
Fig. 1
150-Ton HYDRA HOOK
Fig. 2
Major Parts of HYDRA HOOK
Web Wilson and Hydra-Hook are licensed trademarks of National Oilwell Varco, L.P.
19
CAVINS ROD TYPE SAND PUMP
For General Production Clean Out Service
2853 Cherry Avenue
Signal Hill, CA 90755
Ph: (562) 424-8564
Fax: (562) 595-6174
OIL WELL TOOLS
This very rugged and efficient Sand Pump is used for general utility production clean out
work where it is not necessary to flush the perforations by means of hydraulic surge. It will
function very efficiently in wells having little fluid and also where fluid in the wells is of a
heavy viscous nature down to 9° A.P.I. gravity. A special blow-out feature is incorporated
which utilizes any gases entrained in the well fluid to discharge the load. A Quick Change
Rope Socket, Sinker Bar, Bottom Sleeve, regular flat adjustable Shoe, Dump Key, and
Wood Clamp (Fig. 1) are furnished as standard equipment with all Sand Pumps 1-3/4" O.D.
and larger.* Load Tubes, Bridge Buster Shoes (Fig. 3), Chisel Shoes (Fig. 4), Rein Jars or
Tubular Jars can be supplied along with many other accessories.
*O.D. of wire line must be specified when ordering.
The Bridge Buster
Shoe is used to break
up hard packed sand
and bridges. It is
made from alloy
steel, heat treated
and hard faced on the
cutting edge.
Fig. 3
New Style
Old Style
Spring Type Dump Key
Assembly consists of
spring and spring
housing. Is used to
adapt the Dump Key
Wedge for Flat and
Bridge Buster Shoes
and the Round Nose
Shoe Dump Key.
Fig. 1
The Wood Clamp
Assembly slips over
the end of the Working
Barrel or Load Tube.
Its function is to clamp
around the tube and to
suspend the pump
while making up sections of the tool.
20
Fig. 4
The Multi-Lip Plunger (Fig. 2) is available
as a standard feature for most sizes of
Cavins Sand Pumps. It is made of synthetic
oil-resisting rubber and is recommended for
normal bailing operations where the well
temperature does not exceed 200°F. A strong
bond between the high strength rubber and
the steel mandrel on which it is mounted prevents the stripping of rubber, even under
severe operating conditions. The multiple lips
provide a perfect upstroke seal and automatically compensates for wear. In wells where
elevated temperatures are encountered,
such as in secondary recovery operations,
an all metal plunger (Fig. 5) is recommended.
The Plunger is designed with a labyrinth seal
which does not require any packing.
However, “O”-Rings may be used for additional sealing if desired.
The Chisel Shoe is
used to break up hard
pieces of cement,
lime, shale, or rocks
that are too large to
enter the bottom of
the tool. It is made
from alloy steel, heat
treated and hard
faced on the cutting
edge.
Fig. 4
The Metal Plunger is
recommended
for
wells with elevated
temperatures, replacing
the
regular
Plunger assembly.
Suction is attributed
to cascade seals. Is
also effective for use
in wells operating
under normal temperature conditions.
Fig. 5
ENGINEERING DATA
Sand Pump Size
For Use In
Pipe I.D.
Wgt. Lgth*
Lbs. (Feet)
1-1/4" O.D. (Cavins Model 5A)
1-1/2" – 2-1/2" 75
30
1-1/2" O.D. (Cavins Model 4A)
2" – 3"
140
30
1-3/4" O.D. (Cavins Model 3A)
2" – 3"
165
35
2-1/8" O.D. (Cavins Model 2A)
2-1/2" – 4"
265
35
2-5/8" O.D. (Cavins Model A)
3-1/2" – 5"
320
35
3-1/8" O.D. (Cavins Model B)
5" – 8"
400
35
3-3/4" O.D. (Cavins Model C)
6" – Up
500
35
4-1/2" O.D. (Cavins Model E)
6" – Up
630
35
*These lengths are for single section Sand Pumps.
Optionally, we manufacture 40', 50', and 55' Double
Section Sand Pumps for which a load tube section
must be ordered as an accessory.
2853 Cherry Avenue
Signal Hill, CA 90755
Ph: (562) 424-8564
Fax: (562) 595-6174
CAVINS HYDROSTATIC BAILER
Telescoping Valve Section Type
OIL WELL TOOLS
Run on wire line on any type of
hoisting rig.
(Fig. 1)
(Fig. 2)
(Fig. 3)
JUNK BASKETS (Fig. 1)
Cavins Junk Baskets are used with
the Cavins Automatic Hydraulic Suction
Bailer and Fishing Tool for fishing out
movable objects that are too large to
enter the regular bailer bottom. Such
Junk Baskets are extremely successful
in recovering rock bit cones and cutters,
blades from drag bits, pipe slivers, drilled
up cement retainers and bridging plugs,
tubing collars, packer rubbers, etc.
SKEETER BILL (Fig. 2)
Used with the Cavins Automatic
Hydraulic Suction Bailer for cleaning out
around and inside of stuck fish, such as
gas anchors, tubing, etc., preparatory to
fishing with a socket or spear; also to
clean out around other fish which cannot
be recovered, but which may be chased
to bottom in this manner.
It consists of a sub for attaching to
bailer bottom, and a small O.D. thickwalled, seamless tubular extension up to
20 feet long. Available in both straight
and off-set types. In the latter type, the
off-set is not carried beyond the bailer
O.D. (not shown) unless so specified.
When ordering, specify type desired,
length of extension, and size of bailer on
which it is to be run.
BY-PASS VALVE (Fig. 3)
This device is subbed between the
bailer bottom and the Junk Basket. It permits the well fluid to by-pass up through
the Junk Basket, thus permitting the bailer assembly to descend to bottom freely
and without interruption. For use especially with larger size of Junk Baskets
where the clearance between the O.D. of
the basket and the I.D. of the well bore,
or casing, is restricted.
Top Connection
This outstanding Bailer utilizes the
fluid column (500 ft. min.) standing in the
well to create the hydraulic energy
required for its operation. It is the most
efficient tool for breaking hard packed
sandbridges in Casing and Tubing, fishing out all types of movable junk, cleaning out through collapsed pipe, etc. The
CAVINS Junk Basket can be attached to
the bottom of the Bailer for fishing out
movable objects too large to enter the
Regular Bailer Bottom. The Junk Baskets
are extremely successful in recovering
Rock Bit Cones, Cutter Blades from Drag
Bits, Pipe Slivers, drilled up Cement
Retainers, Bridging Plugs, Tubing
Couplings, Packer Rubbers, etc. It will
efficiently flush the perforations.
The CAVINS Hydrostatic Suction
Bailer consists of a Jar Section, a
Suction Chamber, a Telescoping Valve
Section and a Load Chamber. It can be
run on any size wire line and with any
type of hoisting rig. The creation of a
Pressure Differential is accomplished by
the submergence of the Bailer with the
Suction Chamber filling with air at atmospheric pressure. When the tool comes to
rest at the bottom, the weight of the
Suction Chamber Tube and the Jar
Section, which are all located above the
Telescoping Valve Section, opens the
Valve Section and exposes the Atmospheric Pressure in the Suction Chamber
to the greater pressure in the Fluid
Column. This fluid rushes into the empty
Suction Chamber Tube with sufficient
velocity to carry everything with it
which is at or near the Bailer Bottom.
The CAVINS Multi-Surge
Junk Snatcher is a hydrostatic
multi-action junk fishing tool
which runs on drill pipe or tubing and works on the same
principle as the Hydrostatic
Bailer.
Cavins “Wood Clamp” assemblies are supplied with each
Hydrostatic Bailer, as well as
Sand Pumps, to hold the tool
above the well head while it is
being made up or taken apart.
The “Dump Key” is in a spring
loaded housing which can be
securely spiked to the floor to
turn the bottom sleeve assembly to enable the bailer or sand
pump to be emptied of its load.
QUICK CHANGE
ROPE SOCKET
Sinker Bar
VALVE SECTION
ASSEMBLY
REIN JAR
ASSEMBLY
SUCTION
CHAMBER
ASSEMBLY
LOAD TUBE
ASSEMBLY
(Fig. 4)
Liner Guide
Lower Sub
Valve Cap for
Air Leak Test
Relief Valve
BOTTOM SLEEVE
ASSEMBLY
Relief Valve Spring
Screw Wrench
Shoe Complete
With
Adjustable Sleeve
Wood Clamp
Assembly
Bottom Dumping Key
21
“MULTI-SURGE” JUNK SNATCHER
For Recovery of Small Junk in the Well
2853 Cherry Avenue
Signal Hill, CA 90755
Ph: (562) 424-8564
Fax: (562) 595-6174
OIL WELL TOOLS
The Junk Snatcher operates on a pressure-differential principle which permits
repeated high velocity hole-cleaning surges in one run of the pipe. This unique
and efficient multi-Surge Action is obtained without the use of fluid pumps at the surface and with a minimum of manipulation of the fishing string. Complete Junk Basket
Assemblies to accommodate virtually any size hole and fish are available with the
MULTI-SURGE Junk Snatcher. Each lower Junk Basket assembly is threaded to
accommodate the use of the Guide Shoe, or other attachments; to break, shape, or
center junk prior to each surging operation. Each complete surge of the Junk
Snatcher is instantaneous and the operator need only to pick up the fishing string to
ready the tool for repeated operations.
INSTALLATION OF THE CAVINS JUNK SNATCHER
PARTS IN THE DRILL STRING
MAIN
CONTROL
VALVE
(KELLY)
BOX
BOX
SUB
TOP
BOX
PIN
DRILL PIPE
BOX
DRILL
PIPE
DRILL
PIPE
PIN
FLOAT
VALVE
BOX
PIN
SUB
BOX
PIN
PIN
SUB
BOX
BOX
UPPER
JUNK
BASKET
PIN
SUB
BOX
FLUID
BY-PASS
VALVE
PIN
BOX
MAIN
VALVE
BY-PASS
VALVE
UPPER
JUNK
BASKET
LARGE
JUNK
BASKET
PIN
FLOAT
VALVE
BOX
TYPE OF
SHOE
SUB
BOTTOM
PIN
PIN
LOWER
JUNK
BASKET
Fig. 1
SPUD
GUIDE
DRAG
MILLING
BOTTOM
SHOES
Fig. 2
22
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
CLOSED
OPEN
2853 Cherry Avenue
Signal Hill, CA 90755
Ph: (562) 424-8564
Fax: (562) 595-6174
HYDROSTATIC TUBING BAILER
For General Bailing Service
OIL WELL TOOLS
Fig. 1
For more than half a century CAVINS has been the leader in the manufacturing of production bailing equipment for sand. One of the pioneers of proven bailing tools is the CAVINS
Telescoping Hydrostatic Valve Section Bailer for use on wire line. The CAVINS Hydrostatic
Tubing Bailer works on the same principle as the wire line type bailer only it is run on the
tubing string thereby greatly increasing the volume of sand which can be removed with each
run.
The Hydrostatic Tubing Bailer operates on a pressure differential basis utilizing the fluid
column (1000 ft. min.) standing in the well to create the hydraulic energy required for its function. As the tubing string is lowered and contacts the fill the valve section is opened drawing
sand into the string which is trapped by a check valve. This type of operation can continue
until the differential pressure has been equalized. The tubing is then pulled from the well and
cleaned out. If desired the By-Pass Valve Section can be run which allows the string to be
pulled dry above the load of sand.
The Tubing Bailer is one of the most efficient means of sand recovery where high volume
of fill exists in the well. This method is far superior to simple circulating techniques not only
because of the obvious savings of costly time and equipment but also because the sand is
drawn with hydraulic suction rather than high pressure with a circulating pump which actually can force the sand back into the perforations of the well liner. The hydraulic surge from
the Tubing Bailer will effectively flush the perforations during sand recovery operations.
Tubing Bailer
Valve Section
KNOCK OUT
COLLAR
TUBING
BOTTOM
SECTION
WITH
CHECK VALVE
AND SHOE
TUBING
TUBING
BY-PASS
VALVE
By-Pass
Valve
Section
OPTIONAL
SAW TOOTH
SHOE
TUBING BAILER
VALVE SECTION
Bottom Valve Section
With Check Valve and
Bridge Buster Shoe
Optional
Drag Shoe
Fig. 2
23
CAVINS “TURBO” BAILER
For Use With Tubing
2853 Cherry Avenue
Signal Hill, CA 90755
Ph: (562) 424-8564
Fax: (562) 595-6174
OIL WELL TOOLS
The CAVINS “TURBO BAILER” is engineered for fast, efficient well cleanout especially
when large amounts of fill or scale are encountered. It has proven to be a very cost effective
tool over conventional sand line bailers in these situations and unlike the Hydrostatic Tubing
Bailer, the “TURBO BAILER” can be run in shallow or any depth well with a relatively low
fluid level.
The “TURBO BAILER” working barrel chamber is run in the tubing string, utilizing a flapper valve placed strategically to insure positive containment of debris inside the tubing.
HOW IT WORKS
The “TURBO BAILER,” in the tubing string, is set into the existing fluid level of the well at
which point the tool is stroked in a manner similar to a sand pump. The up-stroke evacuates
debris from the well upward through the shoe into the tubing and as a result is trapped above
the flapper valve which closes during the down-stroke motion. As fluid reaches the plunger
assembly, it passes through a check valve and is discharged through return ports back into
the well. This stroking is repeated until the tubing is filled with sand and/or debris.
TURBO
BAILER
The “TURBO BAILER” offers certain advantages over sand line bailers. The lift rod is of
heavy duty hex design which affords the tool to be rotated with the tubing string to facilitate
getting through sand bridges or breaking up hard packed fill.
The “TURBO BAILER” has additional benefits over conventional circulating techniques
including cost reduction through elimination of expensive pumping equipment and special
circulation fluids (minimizing environmental impact) as well as avoiding the use of high pressure in the well which can force sand back through the perforations and into the formation.
In contrast, the “TURBO BAILER” actually cleans the perforations during operation with its
suction action.
The CAVINS “TURBO BAILER” may be run on all sizes of tubing and drill pipe.
SIZES
Model
O.D.
Threads
B
C
E
3-1/8"
3-5/8"
4-1/2"
2-3/8" EUE-8rd
2-7/8" EUE-8rd
3-1/2" EUE-8rd
TO TOP OF
WELL
TURBO BAILER
BUTTOM
SUB
HEX LIFT
ROD 10 1/2’ STROKE
TUBING
STRING
ABOVE
TURBO
BAILER
PORT
HOLES
TUBING
BELOW
TURBO
BAILER
(LENGTH
DETERMINED
BY WELL
CONDITIONS)
FLAPPER VALVE
WORKING
BARREL
BOTTOM
FLAPPER
ASSEMBLY
DRAIN
HOLE
SAW-TOOTH
SHOE
PERFORATED
NIPPLE
SAND
DEBRIS, ETC.
Fig. 2
24
SAW-TOOTH
SHOE
Fig. 1
BRIDGE
BUSTER
SHOE
2853 Cherry Avenue
Signal Hill, CA 90755
Ph: (562) 424-8564
Fax: (562) 595-6174
CAVINS DEPTHOMETER
For Wire Line Well Measuring
OIL WELL TOOLS
DEPTHOMETER WITH FLOORSTAND
The Cavins Depthometer has no equal for quick, accurate wire
line measurements of oil, gas and water wells, particularly when
perforating, bailing, cleaning out, swabbing, single shot, or similar
operations. It has proven valuable in both on-shore and off-shore
operations. This tool is also used for measuring armored cable for
submersible pumps. The Cavins Depthometer has made “stringing-in” obsolete, and is being adopted as standard equipment for
production and well drilling operations. The Cavins Depthometer is
available for 7/16" – 5/8" O.D. wire lines and 3/4" – 1" O.D.
The range for which the Depthometer is to be used must be
specified on the order. If the tool is to be used for both ranges, an
extra main measuring wheel can be supplied, which can be
exchanged in the field in a few minutes time. Cavins Depthometers
are available for recording measurements in feet or meters. They
can be supplied with all bronze bearing construction Model “BL” or
all ball-bearing construction Model “CL”.
When ordering, please state the following information:
Range of Wire Line size
Measuring in feet or meters
Model “BL” All Bronze Bearing type
Model “CL” All Ball Bearing type with or without
carrying case and stand or with Carrying Case
and Hanger
Each Cavins Depthometer bears a Model Number and Serial
Number. The range of size lines for which it is to be used is
stamped on one spoke of the main wheel. When ordering spare
parts please mention the Model, Serial Number and Wire Line
size.
Shipping Weights and Measurements
Net Weight 36 Lbs. 16.3 Kg.
Tare Weight 24 Lbs. 10.9 Kg.
Gross Weight 60 Lbs 27.2 Kg.
Export Shipping Case: 14" x 17" x 21" = 2.9 Cu. ft. –
36 x 43 x 53 Cm. = .08 Cu. Meters.
Depthometers for special wire line size are available on application.
Maximum Reading 999,999 Feet or 999,999 Meters.
Net Weight of Depthometer Only11 Lbs 5.0 Kg.
Fig. 2
M450
Fig. 3 M460-L
Fig. 1
M430
DEPTHOMETER EYE BOLT HANGER
To facilitate the safe handling of the Cavins
Depthometer on rigs where it is impractical or
impossible to securely anchor to the usual
Floor Stand, an Eye Bolt Hanger can be supplied. It can be supported from a sand line or
cat line from the rig top. The hanger engages
the Depthometer in exactly the same manner
in which the floor stand is attached and simplifies the removal of the tool.
DEPTHOMETER
CARRYING CASE
The Cavins Depthometer
and Stand or Eye Bolt
Hanger can be supplied with
a heavy duty, light weight
carrying case. It protects the
instrument and especially
the counter from the elements and provides a compact storage place for complete assembly.
25
2853 Cherry Avenue
Signal Hill, CA 90755
Ph: (562) 424-8564
Fax: (562) 595-6174
ELECTRONIC DEPTHOMETER
OIL WELL TOOLS
CAVINS is pleased to announce the introduction of a
Depthometer equipped with Electronic displays for use on Coil
Tubing units. The displays are mounted in a NEMA 4 rated
enclosure and optionally can be mounted on a face plate to fit
in your control console. The unit comes standard with the following features:
The unit displays both Depth and Rate of Tubing travel.
By simply adjusting the calibration, display can be either in
feet or meters.
As the main wheel wears, accuracy can be maintained by
field calibration.
A direction switch allows the counter to increment from zero
regardless of the manner in which the depthometer is
mounted.
The counter allows an alarm to sound for up to 99.99 seconds when a preset depth is reached.
The rate display can be programmed to sound an alarm
when the rate of tubing travel falls outside of a preset range.
A conversion kit is available to convert an existing mechanical depthometer into an Electronic display type.
Counter/Rate display features:
English Prompts
Easy to Read
Easy to program
Large LED Display
5 Digits
High Intensity
High Contrast
Sealed Front Panel
NEMA 4 rated
Oil Tight
WaterTight
Chemical Resistant
Power Input
110 VAC or 10-26 VDC
EXTRA LARGE COUNTERS
FOR CAVINS DEPTHOMETERS
An optional Extra Large Counter is available when ordering
a new Depthometer or as a conversion kit for your own Cavins
Depthometer.
The Extra Large Counter has full 3/4" high numerals which
are more than twice the size used on the standard
Depthometer counter and facilitate easier reading in applications where the unit is mounted a short distance away from the
operator such as on coiled tubing rigs.
The following configurations (Fig. 3) are available for the
Extra Large Counter. Our standard configuration is #3, however, the configuration for your use may vary according to your
particular application and mounting location of the
Depthometer on your rig.
26
Fig. 2
Extra Large Counter
1
2
3
4
Fig. 3
Counter Rotations
To order a complete Depthometer with the Extra Large
Counter or a conversion kit please specify the same information as for a standard Depthometer and add the wording; with
Extra Large Counter with 3/4" numerals and also specify the
desired configuration (1, 2, 3 or 4).
2853 Cherry Avenue
Signal Hill, CA 90755
Ph: (562) 424-8564
Fax: (562) 595-6174
BALL LOCK OIL SAVER
For: Blow-Out Prevention and Line Wiping
OIL WELL TOOLS
The Ball-Lock Oil Saver is
standard with the popular
Steel Hydraulic Bonnet. It
is completely reliable for
efficient line wiping action
and is designed to reach
maximum utilization of the
Packing Rubber
S-H500
HYDRAULIC PUMP & HOSE
The optional Hydraulic Bonnet is a self contained
unit and features a Bonnet pump and Handle for
ease of operation. Fig. 2
S-HP150
S-1
Fig. 4
The Screw-Type Bonnet is available for Manual
Operation. Fig. 3
BALL LOCK OIL SAVERS
Fig. 1
(Shown 4" S-15BX
with Remote Bonnet)
The use of the Ball Lock Oil Savers by drilling and production departments
has earned this service proven tool a reputation for trouble-free operation with
simplicity. The CAVINS Ball Lock Oil Savers (Fig. 1) are made of high carbon
steel and precision machined for demanding dependability and safety in a wide
range of service applications. Exhaustive testing in the excess of 3000 psi is further assurance against failure or leakage. Incorporated in its design, which
affords a cleanly wiped wire line, is its safeguard against blow out. One important feature of the Oil Saver is its automatic ball release design. Hardened Steel
Balls hold the traveling assembly securely in the body until released by the
upward travel of the Rope Socket. The Rubber Packing unit with its internal fins
provide the ultimate in wire characteristics with only a normal pressure, or drag,
on the line. The Packing Rubber is compounded of special abrasive and oil resistant properties to give the rubber longer wear. A tough spark-proof die cast alloy
is utilized in the top and bottom line guides and enhances reduced wear in the
rubber packing unit. A high quality leather hydraulic packing ring wards against
leakage in the area between the body and the traveling assembly.
The Steel Hydraulic Bonnet is Standard Equipment for Cavins Ball Lock Oil
Savers. The Hydraulic Bonnets provide an even greater degree of wiping efficiency. The wire line can be completely stripped of all oil, or water and an Oil
Saver outfitted with a Hydraulic Bonnet foregoes the necessity of tools for “taking up” wear in the packing element. The one hand operation requires only a few
strokes of the pump handle to give complete wiping action or turn the release
valve when no wiping is required. The Hydraulic action affords a greater rubber
contact surface as the packing rubber is compressed around the line. The line is
completely surrounded and sealed from blow-out leakage by the action of the
Hydraulic unit. There is no danger of packing rubber or other elements falling
into the well.
27
2853 Cherry Avenue
Signal Hill, CA 90755
Ph: (562) 424-8564
Fax: (562) 595-6174
BLOW OUT PREVENTER
and ROD STRIPPER
OIL WELL TOOLS
The combination Blowout Preventer and Sucker Rod Stripper combines safety and economy in a tool designed to perform the
necessary function of line wiping. It can be operated from anywhere on the derrick floor utilizing pressure from bottled nitrogen,
an optional hand operated hydraulic pump, or the optional BOP control system (Fig. 1C). When this tool is employed of wire line
operations, a CAVINS Ball Lock Oil Saver is screwed directly into the top of the Blowout Preventer. When swabbing, a short lubricator the length of the swab between the master gate and the Blowout Preventer is all that is required. The Blowout Preventer is
available in either the 3" size with full 3" ID clearance and 4" female. A.P.I. line pipe for the Ball Lock Oil Saver on top or the 4"
size with full 4" ID clearance and 4" female A.P.I. line pipe threads top and bottom. Pressure connection is for 1/4" A.P.I. pipe. The
units are tested to give full closure up to 3000 psi well pressure with no leakage. The full closure feature of the Blowout Preventer
will give a temporary seal, allowing ample time to close the master gate should a well blowout occur.
As a Sucker Rod Wiper, the unit affords exceptionally long wiping service and complete control of the well against possible
leakage or blowout. The rubber wiping unit is comparatively inexpensive and very easy to change.
Fig. 1A
Blowout Preventer
Model S-BP50-A (3" I.D.)
Fig. 1B
Blowout Preventer
Model S-BP50-B (4" I.D.)
B O P CONTROL SYSTEM
The BOP Control System provides the hydraulic power
and controls necessary to operate the Cavins Blow Out
Preventer and Rod Stripper during work-over operations
(Fig. 1C). Due to its compact design, the unit takes up little
space and also stores all accessories, controls and BOP
equipment. The BOP accumulator is powered by rig air (26
CFM @ 100 PSI) to charge and maintain pressure stored in
the system. The accumulator provides 3000 PSI + to the
BOP, which gives an immediate closure or it can be manually operated by a 2 stage hand pump for stripping operations. The BOP Control System can be configured a variety
of ways depending on what accessories or options are
required by the customer.
S-BP100
Fig. 1C
28
2853 Cherry Avenue
Signal Hill, CA 90755
Ph: (562) 424-8564
Fax: (562) 595-6174
CEMENT DUMPS
Bridging Plugs and Quick-Change Rope Sockets
OIL WELL TOOLS
CAVINS – CEMENT DUMP
Sub
Rope Socket
Tubing
Thread
Bumper
Ring
Bumper
Spring
Sub
Lock
Spring
Recess
Coupling
Cement
Dump
Cement Dump
Window
Mandrel
Tube
Carriage
Lock
Spring
Friction
Springs
Retaining
Wire
Coupling
The CAVINS Cement Dump, a highly successful device is
attached to the lower end of any desired number of tubular sections, equipped with a rope socket immediately above the loading
window. The assembly is run on a Wire Line. The full opening of the
cement dump is closed by means of a thin, drillable disc, which is
positively released at any desired point in the well when the tool is
raised by the hoist operator. This permits the placing of any desired
amount of cement in a continuous operation. It eliminates the loss
of time involved by waiting for previous loads of cement to set up
and avoids the necessity of running into green cement on succeeding trips.
The cement slurry is discharged in a compact mass through the
full open dump with the assurance that it will not be diluted by the
well fluid. Fresh Water, sand mixed with oil, acid and concrete mixtures are readily dumped. The Cavins Cement Dump contains no
valves or other parts which might become fouled or clogged.
Accidental or premature unloading due to line whip or faulty brakes
is avoided by the amount of free travel built into the friction spring
assembly. The spring carriage is in its upper position when going
into the well carrying the load of Cement. When pulling the Cement
Dump up by the Wire Line, the friction springs retain the carriage in
its position against the casing wall. As the cement Dump moves
upward the carriage opens the toggles which hold the disc in place,
thus releasing the load.
TECHNICAL DATA
1-2 or 3 Lengths
of Tubing, as
Required
(Fig. 1)
Trip
Levers
(Fig. 2)
Bridging
Plug
(Fig. 3)
Cement Dump
Size
Lugs
1-1/2"
2"
2-1/2"
3"
For Use in Casing O.D.
2-A
A
B
C
4" to 4-3/4"
5" TO 7-5/8"
6-5/8" TO 10-3/4"
10" TO 16"
CAVINS BRIDGING PLUGS
DISC
CAVINS “QUICK-CHANGE”
ROPE SOCKET
NAILS
1-3/8” O.D.
K2A403
NOTCHED
DOGS
2” O.D.
KA403
2-1/2” O.D.
KB403
FRICTION
BRUSHES
3-1/4” O.D.
KC403
(Fig. 5)
(Fig. 4)
Drillable Discs used to Close
Bottom of Mandrel.
The CAVINS Bridging Plug is made of drillable material and is used to form
an off-bottom bridge on which cement, sand, and other materials can be
dumped. Canvas seal rings form a base onto which the material to be dumped
comes to rest when it is unloaded. Any tools used to drill out or break up
cement will easily destroy the Bridging Plug. It is set in the Casing by attaching the disc on top of the Bridging Plug to the Cavins Cement Dump which is
used as a setting tool and lowered to the desired point.
Raising the Cement Dump releases the Fingers which have secured the
Plug to the bottom. When the Bridging Plug is thus released, notched dogs,
which are spring loaded and hinged to swing outwardly, are also released and
engaged with the Casing wall to secure the plug against downward movement.
Friction Brushes prevent ordinary movement of the plug until the engaging
dogs take hold.
DRILLABLE DISCS
Part #
O.D.
K2A -403
KA -403
KB -403
KC -403
1-3/8"
2"
2-1/2"
3-1/4"
The CAVINS Quick-Change Rope
Socket is a swivel type socket which does
away with the necessity of having to babbitt a rope socket to the sand line before
starting each job and then cutting it off
after the job is completed. Thus, it saves
considerable time and eliminates the hazard of having to build fires near the well to
melt the babbitt. A small steel thimble,
which has a pull test of greater than 50%
of the strength of the wire line, is permanently babbitted to the line. Alternately a
resin type Babbitt material is now available
which eliminates the need for open fire or
hotwork. The thimble is kept on the line at
all times and it is interchangeable with and
fits all sizes of Cavins Quick-Change Rope
Sockets. To remove one size socket from
the line and install another one, takes only
a few seconds time.
TECHNICAL DATA
Rope Socket O.D.
Size of Box Connections
1-5/8
1-3/4
2
2-1/4
2-1/2
2-3/4
3/4 API Sucker Rod Box
3/4 API Sucker Rod Box
1 x 1-1/2–8 THD 3" Taper
1-1/8 x 1-3/4–8 THD 2-5/8" Taper
1-1/8 x 1-3/4–8 THD 2-5/8" Taper
1-1/8 x 1-3/4–8 THD 2-5/8" Taper
WIRE
ROPE
CAP
LINER
(SPLIT)
ROPE
THIMBLE
BODY
Fig. 6
NOTE: The above noted Box Connections are
standard Cavins Joints. Any type of Joint
can be cut on these Rope Sockets to
customer’s specifications.
29
RUBBER PRODUCTS
and ACCESSORIES
2853 Cherry Avenue
Signal Hill, CA 90755
Ph: (562) 424-8564
Fax: (562) 595-6174
For Well Servicing Operators
OIL WELL TOOLS
WIRE LINE
WIPING ELEMENT
CODE STUBBLE
9", 12" & 14" Flat Pipe Wiper
(Flat Pipe Wiper Holders are also available)
NUT
WASHER
EYE BOLT
CHAIN
Wire Line “Pig Tail” Wiper
10" Handle Bar Pipe Wiper
LID
NO. 10-0451
RUBBER WIPER
NO. 10-0700
BODY
NO. 10-0457
Tong Pullback Strap
Sucker Rod Wiper Holder
Sucker Rod Wiper
30
Elevator Balancing Strap
2853 Cherry Avenue
Signal Hill, CA 90755
Ph: (562) 424-8564
Fax: (562) 595-6174
CONVERTIBLE
CAT-LINE GRIP
OIL WELL TOOLS
REGULAR AND ROLLER TYPE MODELS
Purpose: To assure that the cat-line is held securely at any
desired point.
Description: The Cavins/BJ Convertible Cat-Line Grip has an
eccentric cam type grip shaped to the contour of conventional 11/2" cat-line rope. The specially-shaped teeth, of this grip, when
locked against the braking horizontal face, take a positive grip without damaging the cat-line rope.
Two Models: The Regular Model has direct access by the cat-line
rope to the cam type grip. The Roller Type Model has a special outboard sheave that acts as a roller guide to give additional cat-line
control where particular installations may benefit from added directional control.
Special Convertible Feature: This Cavins/BJ Cat-Line Grip
design is engineered to be readily convertible to either right or left
hand gripping position both in Regular and Roller type models.
Change to right or left position is done by simply removing the
main pin holding the grip and control handle and switching the grip
and handle direction. Similarly, the outboard sheave on the Roller
Type model can be transposed, thus any Cavins/BJ Cat-Line Grip
model can be converted from Driller’s Side Right Hand Grip to
Automatic Cathead Side Left Hand Grip or visa-versa.
Additional Features: Both Regular and Roller Type Models are
additionally convertible in that the outboard roller sheave can be
added to the Regular Model by a simple bolt-on arrangement or
detached from the Roller Type Model when a Regular Type installation is desired.
Capacity: Both Regular and Roller Type models are designed to
handle a 6000-lb. working load.
SPECIFICATIONS–ROLLER TYPE
(RIGHT OR LEFT)
Order by Part Number and Part Name
Part Name
No.
Req’d.
Part No.
Left Hand
Part No.
Right Hand
Roller Type Cat-Line Grip Complete
Cat-Line Grip Assembly
Body
Grip
Lever
Right Lock
Left Lock
Socket Head Shoulder Screw
Roll Pin
Sheave Housing Assembly
Sheave Housing
Sheave Assembly
Sheave
Grease Fitting
Sheave Pin
Socket Head Cap Screw
Lock Nut
—
1
1
1
1
1
1
2
1
1
1
1
1
1
1
2
2
34701-1
34700-1
34695
10263
23727
10265-1
10191
940585-37
947129-182
34699
34697
23620-1
31666
940308-1
23619
941286-71
941442-3
34701
34700
34695
10263
23727
10265-1
10191
940585-37
947129-182
34699
34697
23620-1
31666
940308-1
23619
941286-71
9414442-3
Part Name
No.
Req’d.
Part No.
Left Hand
Part No.
Right Hand
Regular Cat-Line Grip Assembly
Body
Grip
Lever
Right Lock
Left Lock
Socket Head Shoulder Screw
Roll Pin
1
1
1
1
1
1
2
1
34700-1
34695
10263
23727
10265-1
10191
940585-37
947129-182
34700
34695
10263
23727
10265-1
10191
940585-37
947129-182
SPECIFICATIONS–REGULAR TYPE
(RIGHT OR LEFT)
Order by Part Number and Part Name
Cavins/BJ Regular Type Convertible Cat-Line Grip
Cavins/BJ Roller Type Convertible Cat-Line Grip
Cavins/BJ Roller Type Convertible Cat-Line Grip
31
2853 Cherry Avenue
Signal Hill, CA 90755
Ph: (562) 424-8564
Fax: (562) 595-6174
“T” SAFETY CLAMPS
OIL WELL TOOLS
BAASH-ROSS® Type “T” Safety Clamps
The Type “T” Safety Clamp is designed for small diameter pipe
1-1/8" through 4-1/2" O.D. Each link changes the effective
working range approximately 1" in diameter.
The positive automatic gripping principle is ideal to help safeguard against dropping strings of flush tubing, to provide a
shoulder to position strings of flush line pipe for welding, and
many other applications.
TABLE NO. 1
Type T Safety Clamp Complete With Box
Total No. Links Req’d. Range O.D., Sizes
Per Range
From
To
Part
Number
Weight
Lbs. Each
4
5
6
7624-5044
7624-5045
7624-5046
84
88
92
Part
Number
Weight
Lbs. Each
As Ordered
1
1
1
7624-B-7
7624-A-18
7624-A-21
900620-52
4-1/4
3-1/4
1/4
1/4 oz.
1-1/8"
2-1/8"
3-1/4"
Item
No.
2"
3-1/4"
4-1/2"
Replacement Parts
No.
Req’d.
Item
1
2
3
3A
Link Assembly, Complete
Link, Intermediate
Slip with Cotter
Cotter, for Slip (1/4")
4
5
5A
6
Slip Spring
*Link Pin with Cotter
*Cotter, for Link Pin (3/16")
End Link (Screw)
1
1
1
1
7624-B-21
7624-C-5
939672-36
7624-A-20
1/2 oz.
3/4
1/4 oz.
4-1/2
7
8
9
10
End Link (Pivot Black)
*End Link Pin with Chain
*Screw
*Nut
1
1
1
1
7624-A-19
7624-F-5
7624-A-5
7624-B-5
3-1/2
1-1/4
4
1-1/2
11
12
13
14
*Nut Wrench
*Pivot Block
*Pivot Block Pin
*Pivot Block Pin Wrench
1
1
2
1
7624-A-25
7624-A-5000
7624-D-5
900533-12
3-1/2
1-1/2
1/4
1/8
15
16
25
Handle Assy.
Handle Link Pin
*Equipment Box
1
2
1
7624-A-22
7624-G-5
7624-A-9
4
12 oz.
45
1
8
6
2
7
15
4
3
5
14
16
10
9
12
13
*These Parts are interchangeable with the “C” Type Clamps.
Recommended Spare Parts for remote locations–3 pieces Intermediate Link
(Item 2), 1 set Slips with retaining Cotter (Item 3), 3 pieces Link Pin with Cotter
(Item 5), 1 set Slip Springs (Item 4).
11
Baash-Ross is a licensed trademark of National Oilwell Varco, L.P.
FIELD OFFICES
BAKERSFIELD, CA
1519-32nd Street
P.O. Box 2384
Bakersfield, CA 93303-2384
(661) 327-7154
Fax: (661) 327-7155
TAFT, CA
VENTURA, CA
815 Main Street
P.O. Box 695
Taft, CA 93268-3268
(661) 765-2181
Fax: (661) 765-2182
1641 N. Ventura Ave.
Ventura, CA 93001-1577
(805) 643-6767
Fax: (805) 643-1362
OIL WELL TOOLS
A Division of DAWSON ENTERPRISES
2853 Cherry Avenue, P.O. Box 6039
Long Beach, CA 90806-0039
Ph: (562) 424-8564 • Fax: (562) 595-6174
E-mail: oiltools@cavins.com
www.cavins.com
CC 2002-03 (Rev. 2012)
Printed In United States