Siemens CMTC1913 User manual

CMTC1713 / CMTC1913
TFT LCD Monitor
User Manual
Building Technologies
Fire Safety & Security Products
Technical specifications and availability subject to change without notice.
© 2008 Copyright Siemens Switzerland Ltd
We reserve all rights in this document and in the subject thereof. By acceptance of the document the recipient acknowledges these rights
and undertakes not to publish the document nor the subject thereof in full or in part, nor to make them available to any third party without our
prior express written authorization, nor to use it for any purpose other than for which it was delivered to him.
Table of contents
1
General safety instructions..........................................................................4
1.1
Installation .......................................................................................................4
2
Standards and guidelines ............................................................................5
2.1
EU directives ...................................................................................................5
3
Technical data ...............................................................................................6
4
Details of ordering ........................................................................................6
5
Dimension drawings .....................................................................................7
6
Package contents..........................................................................................7
7
Hardware Description ...................................................................................8
7.1
Connections ....................................................................................................8
7.2
Buttons and controls .......................................................................................8
7.3
Remote functions ............................................................................................9
7.4
Power management ........................................................................................9
8
Mounting the monitor .................................................................................10
9
Adjusting the OSD screen..........................................................................11
9.1
Picture ...........................................................................................................11
9.2
Sound ............................................................................................................12
9.3
Setup .............................................................................................................13
9.4
Information ....................................................................................................14
10
Troubleshooting ..........................................................................................15
11
Disposal .......................................................................................................16
12
Index .............................................................................................................17
3
Building Technologies
Fire Safety & Security Products
CMTC1713_1913 User Manual
19/12/2008
General safety instructions
1
General safety instructions
z
Read the general safety precautions before operating the device.
z
Keep this document for reference.
z
Always pass this document on together with the product.
z
Please also take into account any additional country-specific, local safety
standards or regulations concerning project planning, operation and disposal of
the product.
Liability claim
z
Do not connect the device to the 230 V supply network if it is damaged or any
parts are missing.
Danger of electrical shock on the open device
z
1.1
The device may only be opened by trained service technicians.
Installation
z
The device is approved for use within the European Union. When used in
countries outside the European Union, the national or local requirements for
approval must be met before operating the device.
Damage due to unsuitable mounting location
z
Do not operate the device close to sources of powerful electromagnetic
radiation.
z
The device should only be used for indoor applications.
z
Protect the device against moisture.
Danger of electrical shock due to incorrect connection
z
Connect the device only to power sources with the specified voltage. Voltage
supply requirements can be found on the rating label of the device.
Danger of electrical shock due to unsuitable power source
z
Use only the plug-in power supply unit that is included in the delivery.
z
Use the plug-in power supply only in conjunction with a power supply cable that
has been approved in your country and complies with the national standards.
4
Building Technologies
Fire Safety & Security Products
CMTC1713_1913 User Manual
19/12/2008
Standards and guidelines
2
Standards and guidelines
2.1
EU directives
This product complies with the requirements of the following European directives.
The EU declaration of conformity is available to the responsible agencies at:
Siemens Building Technologies
Fire & Security Products GmbH & Co. oHG
76181 Karlsruhe
Germany
European Directive 2004/108/EC „Electromagnetic Compatibility”
Compliance with the European Directive 2004/108/EC has been proven by testing
according to the following standards:
Emitted interference:
EN 61000-6-3
Interference resistance:
EN 50130-4
European Directive 2006/95/EEC „Low-Voltage Directive”
Compliance with the European Directive 2006/95/EEC has been proven by testing
according to the following standards:
Safety:
EN 60950-1
5
Building Technologies
Fire Safety & Security Products
CMTC1713_1913 User Manual
19/12/2008
Technical data
3
Technical data
CMTC1713
CMTC1913
Panel type
17˝ TFT color LCD panel
19˝ TFT color LCD panel
Screen size
431 mm (diagonal)
480 mm (diagonal)
Viewable Size (H x V)
337.9 x 270.3 mm
376.32 x 301 mm
Dot pitch (H x V)
0.264 x 0.264 mm
0.294 x 0.294 mm
Viewing angle (H / V)
160° / 160°
Contrast ratio
1000:1
800:1
cd/m2
Brightness
300
Resolution (H x V)
1280 x 1024 pixel
Display colors
16.2 M
Response time
5 ms
Power requirements
(PSU)
100 – 240 V AC
Power requirements
(Monitor)
DC 12 V / 3 A
Power consumption
50 W
Scan frequency
H :31 - 64 KHz; V: 56 - 75 Hz
Input
PC
DC 12 V / 3.5 A
Resolution: SXGA (1280 x 1024 @60 Hz)
Connector: DVI-D
z Scan frequency: H: 31 - 64 KHz; V: 56 - 75 Hz
VIDEO
z Standard: PAL / NTSC
z Connector: 2 x BNC (composite video), 1 x Mini DIN 4pol (SVideo, Y/C)
z Level: 1.0 Vp-p, 75 Ohm terminated
AUDIO
z Built-in speakers: 2 x 2 W stereo sound
z 1 x Phone jack for PC sound, 1 x Cinch for video sound
z
z
4
OSD languages
English, French, German, Italian, Spanish, Portuguese, Dutch
Dimensions (W x H x
D)
382 x 391 x 200 mm
(with base)
430 x 425 x 200 mm
(with base)
Weight
6.2 kg
6.6 kg
Wall mount
VESA 100 standard
Approvals
CE
Details of ordering
Type
Order No.
Designation
Weight
CMTC1713
S54573-C4-A1
17" TFT CCTV Monitor
6.2 kg
CMTC1913
S54573-C5-A1
19" TFT CCTV Monitor
6.6 kg
6
Building Technologies
Fire Safety & Security Products
CMTC1713_1913 User Manual
19/12/2008
Dimension drawings
5
6
Dimension drawings
Dimension
CMTC1713
CMTC1913
1
Width monitor
382 mm
430 mm
2
Width base
243 mm
243 mm
3
Height monitor
330 mm
371 mm
4
Height monitor (with base)
392 mm
423 mm
5
Depth monitor
60 mm
62 mm
6
Depth monitor (with base)
195.5 mm
195.5 mm
Package contents
z
1 x Power supply 100 – 240 V AC (incl. power cable)
z
1 x VGA cable
z
1 x DVI cable
z
1 x Adapter (VGA to DVI)
z
1 x Audio stereo cable
z
1 x Remote control (incl. batteries)
z
1 x User manual
7
Building Technologies
Fire Safety & Security Products
CMTC1713_1913 User Manual
19/12/2008
Hardware Description
7
Hardware Description
7.1
Connections
2
1
7.2
3
4
5
6
7
8
1
DC 12V IN
DC power input
2
DVI IN
PC signal input
3
VIDEO 1 IN
Composite signal input for AV1
4
VIDEO 1 OUT
Video looping output for AV1
5
VIDEO 2 IN
Composite signal input for AV2
6
VIDEO 2 OUT
Video looping output for AV2
7, 8
AUDIO IN (L+R)
Stereo audio signal input for video
9
S-VIDEO IN
Y/C separated signal input
10
S-VIDEO OUT
Y/C separated signal looping output
10
PC STEREO IN
Stereo audio stereo input for PC
9
10
11
Buttons and controls
1
2
3
4
5
6
7
8
1
SOURCE
Selects input source (AV1, AV2, S-Video, DVI-D, DVI-A)
In OSD menu: Enters sub menu
2
MENU
Enters and exits the OSD menu [J 11]
In OSD menu: Exit sub menu
3
AUTO / ▼
Auto geometry adjustment (only in DVI-A mode)
In OSD menu: Moves downwards in the menu
4
▲
In OSD menu: Moves upwards in the menu
5/6
◀ VOL ▶
Adjusts the volume
In OSD menu: Adjusts menu settings or enters/exits the submenu
7
IR SENSOR
Remote control sensor
8
POWER
SWITCH
Turns the power ON or OFF
9
POWER LED
Shows the monitor power status
(Green = The power is turned ON; Red = The power is turned
OFF)
See also chapter Power management [J 9]
9
8
Building Technologies
Fire Safety & Security Products
CMTC1713_1913 User Manual
19/12/2008
Hardware Description
7.3
Remote functions
POWER: Turns the power ON or OFF
SOURCE: Selects input source (AV1, AV2, S-Video, DVI-D, DVIA)
APC (Auto Picture Control): Selects Picture mode [J 11]
ACC (Auto Color Control): Selects Color tone [J 11]
AV1: Selects AV1 input source
AV2: Selects AV2 input source
S-VIDEO: Selects S-VIDEO input source
PC: Selects DVI input source (DVI-A, DVI-D)
AUTO: Auto geometry adjustment (only in DVI mode)
MUTE : Mutes the sound
MENU: Enters and exits the OSD menu [J 11]
EXIT: Exits the OSD menu
VOL◀▶: Adjusts the level of audio volume
UP/DOWN: Moves upwards/downwards in the OSD menu
ENTER: Enters an OSD submenu or accepts your selection
INFO: Displays information about input source and picture mode
STILL: Pauses the picture
7.4
Power management
This monitor features a power management system to “power down” upon receipt
of a signal from a VESA DPMS-compliant video card.
Display Power Management Signaling (DPMS) is a VESA interface standard that
reduces power to computer monitors, when not in use. DPMS defines 4 power
management modes for monitors in idle state: Power On, Standby, Suspend and
Power Off.
Power consumption
Mode
Power consumption
Power On
< 50 W
Standby
< 11 W
Suspend
< 11 W
Power Off
< 8.5 W
LED Indicator
Mode
Color
Monitor operation
Power On
Green
Normal operation
Standby
Red blinks
Screen blanks after preset idle time and the monitor
shuts down
Red
Not operation
Suspend
Power Off
9
Building Technologies
Fire Safety & Security Products
CMTC1713_1913 User Manual
19/12/2008
Mounting the monitor
8
Mounting the monitor
The LCD monitor CMTC1713/1913 is suitable for wall mounting by using the VESA
100 standard wall mount design.
1. Remove the base from the monitor by loosen the screws on the back panel.
2. Install the monitor to the wall as shown in the picture below.
10
Building Technologies
Fire Safety & Security Products
CMTC1713_1913 User Manual
19/12/2008
Adjusting the OSD screen
9
Adjusting the OSD screen
All picture and sound settings for the monitor can be adjusted in the OSD menu
(On Screen Display).
To adjust the OSD screen:
1. Press the Menu button to enter the OSD menu.
2. Press the ▲/▼ buttons to select the desired option.
Ö The selected option is highlighted.
3. Press the ▶ button to enter the submenu for adjusting items.
4. Change the value you wish to adjust by using the ◀/▶ buttons.
5. Press the ◀ button to exit the submenu for adjusting items.
6. Press the Menu button to exit the OSD menu.
Ö The OSD menu disappears.
Ö All settings are saved automatically.
The OSD menu automatically disappears after a preset if no settings are made.
9.1
Picture
Option
Function
Values
Brightness
Adjusts brightness of the screen 0 - 100
Contrast
Adjusts intensity of the image
0 - 100
Color *
Adjusts color of the picture
0 - 100
Tint *
Adjusts tint of the picture
0 - 100
Color Tone
Sets color tone
See table below
Picture Mode
Sets picture mode
See table below
Size
Displays picture size
4:3
Sharpness *
Adjusts sharpness of the picture 0 - 100
*Not available in DVI-A mode
11
Building Technologies
Fire Safety & Security Products
CMTC1713_1913 User Manual
19/12/2008
Adjusting the OSD screen
Color tones
Custom*
To manually adjust the color tones (Red, Green, Blue)
Cool
Gives the white colors a bluish tint
Normal
Gives the white colors a neutral tint
Warm
Gives the white colors a reddish tint
*In DVI-A mode only
Picture modes
Dynamic
Provides enhanced contrast and sharpness
Standard
Provides standard contrast and sharpness
Movie
Is recommended for viewing film-based content
Mild
Reduces contrast and sharpness
Picture modes (in DVI-A mode)
9.2
Custom
Applies user selected values (Brightness, Contrast)
High
Uses the following values:
Brightness= 50, Contrast = 70
Middle
Uses the following values:
Brightness = 50, Contrast = 50
Low
Uses the following values:
Brightness = 40, Contrast = 40
Sound
Option
Function
Values
Volume
Adjusts the level of audio volume
0 - 100
Mute
Mutes speaker sound
On, Off
12
Building Technologies
Fire Safety & Security Products
CMTC1713_1913 User Manual
19/12/2008
Adjusting the OSD screen
9.3
Setup
Option
Function
Values
Language
Sets the language of the OSD menu
English, Français,
Deutsch, Italiano,
Español, Português,
Nederland
Key Lock
Locks all buttons of the monitor
Note: Use remote control to unlock [J 9]
On, Off
OSD Tone
Changes background color of monitor menus
(e.g. input source, information)
Transparency, Blue
Blue
Screen
Displays a blue screen if the monitor receives no On, Off
signal
PC*
See table below
Reset
Resets the monitor settings to their factory
default
*Only available in DVI-A mode
13
Building Technologies
Fire Safety & Security Products
CMTC1713_1913 User Manual
19/12/2008
Adjusting the OSD screen
PC setup (only in DVI-A mode)
9.4
Option
Function
Values
Auto Adjust
Auto geometry adjustment
Phase
Adjusts the number of horizontal picture elements
0 - 100
H-Position
Adjusts the horizontally picture position
0 - 100
V-Position
Adjusts the vertically picture position
0 - 100
Frequency
Adjusts the vertical noise of screen image
0 - 100
Information
Firmware version
Displays the version of the monitor firmware
14
Building Technologies
Fire Safety & Security Products
CMTC1713_1913 User Manual
19/12/2008
Troubleshooting
10
Troubleshooting
Problem
Troubleshooting
No image on display
screen
1. Check that the power cord of the monitor has been
connected securely into wall outlet or grounded
extension cable or strip.
2. Power switch should be in the ON position and LED
is lit.
3. Check that the Brightness and/or the Contrast of the
display have not been turned down to minimum
levels [J 11] .
"Going to sleep"
message on screen
1. Check that the signal cable is completely connected
to the video card/computer.
2. Check that the video card is completely seated in its
slot and the computer is switched on.
Display image is not
centered, too small or
too large in PC mode
1. Press the Auto button (in DVI mode) or adjust
picture settings [J 11] .
Vertical or horizontal
noise is present in the
picture
1. Press the Auto button or adjust Frequency and
Phase in the OSD menu [J 14] .
Can see picture but no
sound is audible
1. Make sure that audio inputs are connected properly.
2. Check to see whether the volume is turned down
[J 12] .
15
Building Technologies
Fire Safety & Security Products
CMTC1713_1913 User Manual
19/12/2008
Disposal
11
Disposal
All electrical and electronic products should be disposed of
separately from the municipal waste stream via designated
collection facilities appointed by the government or the local
authorities.
This crossed-out wheeled bin symbol on the product means
the product is covered by the European Directive
2002/96/EC.
The correct disposal and separate collection of your old
appliance will help prevent potential negative consequences
for the environment and human health. It is a precondition
for reuse and recycling of used electrical and electronic
equipment. For more detailed information about disposal of
your old appliance, please contact your city office, waste
disposal service or the shop where you purchased the
product.
16
Building Technologies
Fire Safety & Security Products
CMTC1713_1913 User Manual
19/12/2008
Index
12
Index
A
O
Adjusting OSD screen, 11
OSD language, 13
Auto adjust, 14
OSD menu, 11
B
P
Buttons, 8
PC setup, 14
C
Picture mode, 12
Color tone, 12
Picture settings, 11
Connections, 8
Power management, 9
Power status, 8
I
Input signal, 8
K
Key lock, 13
L
Language setup, 13
M
Mounting, 10
Mute, 12
R
Remote functions, 9
Resetting, 13
S
Sound settings, 12
T
Troubleshooting, 15
W
Wall mount, 10
17
Building Technologies
Fire Safety & Security Products
CMTC1713_1913 User Manual
19/12/2008
Issued by
Siemens Building Technologies
Fire & Security Products GmbH & Co. oHG
Siemensallee 84
D-76181 Karlsruhe
www.buildingtechnologies.siemens.com
Document ID
A6V10230457
Edition
19/12/2008
© 2008 Copyright Siemens Switzerland Ltd
Technical specifications and availability subject to change without
notice.