White Rodgers 1F95-377 Specifications

WHITE-RODGERS
COMFORT-SET® 90 SERIES
MULTI-STAGE/HEAT PUMP INSTALLATION/CONFIGURATION
INSTALLATION
DESCRIPTION
This White-Rodgers Automatic Setback
Digital Thermostat uses microcomputer
technology to provide precise time and
temperature control. This thermostat offers
the flexibility to design heating and cooling
programs that fit building needs. This
thermostat is adaptable to most 24 volt
residential forced air multi-stage or heat
pump systems with electric or fossil fuel
auxiliary.
SPECIFICATIONS
1F95-377: 7 Day programming; residential applications
ELECTRICAL DATA
Electrical Rating:
20 to 30 VAC, 50/60 Hz with common
0.05 to 1.5 Amps per terminal
2.5 Amps maximum total load (all
terminals combined)
Standard Systems:
Multi-stage gas, oil, electric.
Single-stage or two-stage compressor
heat pump.
THERMAL DATA
Setpoint Temperature Range:
45° to 99°F (7° to 37°C)
Operating Ambient Temperature:
32° to 110°F (0° to 43°C)
Operating Humidity Range:
90% non-condensing max.
Shipping Temperature Range:
-4° to 149°F (-20° to 65°C)
PRECAUTIONS
!
WARNING
Do not short out terminals on gas valve
or primary control to test. Short or
incorrect wiring will damage thermostat
and could cause personal injury and/or
property damage.
Do not use on circuits exceeding
specified voltage. Higher voltage will
damage thermostat and could cause
shock or fire hazard.
Thermostat installation and all components of the system shall conform to
Class II circuits per the NEC code.
! CAUTION
To prevent electrical shock and/or
equipment damage, disconnect electric
power to system at main fuse or circuit
breaker box until installation is
complete.
NOTE
Read all instructions thoroughly before
beginning installation.
This thermostat is intended for use with a
low voltage system. Do not use on a line
voltage system.
Do not exceed ratings shown in the Specifications section, above. If in doubt about the
electrical ratings of your heating/cooling
system, have it inspected by a qualified
heating and air conditioning contractor or
licensed electrician.
All wiring must conform to local and
national electrical codes and ordinances.
This control is a precision instrument, and
should be handled carefully. Rough handling
or distorting components could cause the
control to malfunction.
Part No. 37-6158B
Replaces 37-6158A
0121
INSTALLATION
ATTENTION!
Remove the front cover of the old thermostat. With wires still attached, remove wall
plate from the wall.
Identify each wire attached to the thermostat using one of the labels enclosed with the
new thermostat.
This product does not contain mercury.
However, this product may replace a unit
which contains mercury.
Do not open mercury cells. If a cell becomes
damaged, do not touch any spilled mercury.
Wearing non-absorbent gloves, take up the
spilled mercury with sand or other absorbent
material and place into a container which can
be sealed. If a cell becomes damaged, the
unit should be discarded.
Mercury must not be discarded in household
trash. When the unit this product is replacing
is to be discarded, place in a suitable
container and return to White-Rodgers at
9797 Reavis Road, St. Louis, MO, 631235398 for proper disposal.
Place the base over the hole in the wall
where the wires come out and mark mounting hole locations using the base as a
template. Drill 3⁄16” pilot holes, and install
screw anchors in the wall.
Run wires through hole in base and attach
base to wall (see fig. 1).
Disconnect the wires from the old thermostat
one at a time. DO NOT let the wires fall
back into the wall.
Insert the wires into the terminals on the base
using the appropriate wiring diagram and
tighten the terminal screws.
Install the new thermostat using the following procedures.
CONFIGURING AND PROGRAMMING
ATTACH BASE TO WALL
Remove packing material from the thermostat. Place fingers of one hand on the center
top and bottom portion of the thermostat.
Grasp the base in the other hand on top and
bottom center and gently pull straight out.
Forcing or prying on the thermostat will
cause damage to the unit.
REMOVE OLD THERMOSTAT
Shut off electricity at main fuse or circuit
breaker box until installation is complete
AND the new thermostat is configured
properly.
Before the power is turned on, the
thermostat must be configured to operate
properly with the system. See the CONFIGURATION section of this manual.
This thermostat can be programmed for
automatic temperature control. Refer to
Operating Instructions for programming.
4
3
2
L PH D SA SB SC OT
1
1
R
C
E
C R W3 W2 E2 W1 Y2 Y1 B
A1
P
O
G
5
1 Mounting screws
2 Pull wires through this opening
3 Insert wires into terminal holes, then tighten screws
4 Screw anchors
5 Jumper connections for remote sensor power
(Do not remove)
Figure 1. Thermostat base and terminals
2
MULTI-STAGE TERMINAL OUTPUTS
Refer to equipment manufacturers’ instructions for specific system wiring information.
This thermostat is designed to operate a
single-transformer system. If you have a twotransformer system, cut and tape off one
transformer. If transformer safety circuits are
in only one of the systems, remove the
transformer of the system with NO safety
circuits. If required, replace remaining
transformer with a 75VA Class II transformer.
After disconnecting one transformer, the two
commons must be jumpered together.
You can configure the thermostat for use
with either multi-stage electric heat systems
or multi-stage gas systems. When configured
for electric heat, the G terminal (blower/fan)
will be energized on a call for heat.
Use the terminal output information below to
help you wire the thermostat properly for
your multi-stage system. After wiring, see
CONFIGURATION section for proper
thermostat configuration.
THERMOSTAT TERMINALS (Upper)
L
PH
D
SA
SB
SC
OT
Malfunction Light
X-10 Module Input
Not Used
Remote Sense A
Remote Sense B
Remote Sense C
Outdoor Sensor
THERMOSTAT TERMINALS (Lower)
SYSTEM
Multi-Stage
E
C
R
W3/A1
W2
E2/P
W1
Y2
No Function
24 Volt
(Common)
24 Volt
(Hot)
Heat mode 3rd
stage
Heat mode 2nd
stage
No function
Heat mode
1st stage
Y1
B
O
G
Blower/Fan Energized
Energized in
Cool mode 2nd Cool mode 1st Heat and Off Energized in on call for Cool (and
stage
stage
Cool Mode
Heat if confgured to
Mode
Electric Heat).
HEAT PUMP TERMINAL OUTPUTS
Refer to equipment manufacturers’ instructions for specific system wiring information.
This thermostat is designed to operate a
single-transformer system. If you have a twotransformer system, cut and tape off one
transformer. If transformer safety circuits are
in only one of the systems, remove the
transformer of the system with NO safety
circuits. If required, replace remaining
transformer with a 75VA Class II transformer.
After disconnecting one transformer, the two
commons must be jumpered together.
You can configure the thermostat for use
with the following heat pump system types:
HEAT PUMP TYPE 1. Single-stage
compressor system; gas or electric backup.
HEAT PUMP TYPE 2. Multi-stage or twocompressor system; gas or electric backup.
HEAT PUMP TYPE 3. System requiring
separate signals for heat (W1, W2, W3) and
cool (Y1); gas or electric backup.
Use the terminal output information below to
help you wire the thermostat properly for
your heat pump system type. After wiring,
see CONFIGURATION section for proper
thermostat configuration.
THERMOSTAT TERMINALS (Upper)
L
PH
D
SA
SB
SC
OT
Malfunction Light
X-10 Module Input
Not Used
Remote Sense A
Remote Sense B
Remote Sense C
Outdoor Sensor
THERMOSTAT TERMINALS (Lower)
SYSTEM
E
C
R
W3/A1
W2
E2/P
W1
Y2
Y1
B
O
G
Heat mode
2nd stage
No Output
Heat and cool
mode 1st
stage
(compressor)
Energized in
Heat, Off,
Emergency
Mode
Energized in
Cool Mode
Blower/Fan Energized
on call for Heat and
Cool
Heat and cool Heat and cool Energized in
mode 2nd
mode 1st
Heat, Off,
stage
stage
Emergency
(compressor 2) (compressor 1)
Mode
Energized in
Cool Mode
Blower/Fan Energized
on call for Heat and
Cool
Single-stage compressor system; gas or electric backup
Heat Pump 1*
Emergency
mode 1st
stage
24 Volt
(Common)
24 Volt
(Hot)
E2 - Emergency
Heat mode 3rd
mode constant
Emergency mode
stage.
3rd stage
Emergency mode P - All output.
other modes
2nd stage
constant output.
Multi-stage or two compressor system; gas or electric backup
Heat Pump 2*
Emergency
mode 1st
stage
24 Volt
(Common)
24 Volt
(Hot)
E2 - Emergency
mode constant
Emergency mode Emergency mode
output.
3rd stage
2nd stage
P - All other modes
constant output.
Heat mode
3rd stage
System requiring separate signals for heat (W1, W2) and cool (Y1); gas or electric backup
Heat Pump 3**
Emergency
mode 1st
stage
24 Volt
(Common)
24 Volt
(Hot)
E2 - Emergency
Heat mode 3rd
Heat mode 2nd
mode constant
stage.
stage.
Emergency mode Emergency mode P - All output.
other modes
3rd stage
2nd stage
constant output.
* If system does not provide connection to E, jumper W1 to E to provide Aux heating in emergency mode.
** If system does not provide connection to E, jumper W2 to E to provide Aux heating in emergency mode.
3
Heat mode
1st stage
No Output
Cool mode 1st
stage
Energized in
Heat, Off,
Emergency
Mode
Energized in Blower/Fan Energized
on call for Heat and
Cool Mode
Cool
CONFIGURATION
SWITCHES
RESET SWITCH
See the Troubleshooting section at the end
of this document for more information about
the function of this switch.
1
E2/P SWITCH
The E2/P switch is located on the back of the
thermostat body (see fig. 2). This switch
controls how the E2/P terminal of the
thermostat will be energized. When the
switch is in the E2 position (down), the E2/P
terminal will be energized only when in
emergency heat. When the switch is in the P
position (up), the E2/P terminal will always
be energized except when in emergency heat.
Consult the equipment manufacturer or a
qualified heating/cooling service person
before setting this switch. If your system has
no connection to E2/P, no change in the
switch setting is required.
S18
2
P S19
E2
1 Reset switch
2 E2/P switch
Figure 2. Switch locations on back of thermostat body
INSTALLER CONFIGURATION
BEFORE TURNING POWER ON, please
read the following instructions. Before
operating the system, you must configure
the thermostat to operate properly with
your equipment.
The thermostat, as it comes from the factory,
is configured to operate a standard multistage electric forced hot air system with a
single stage air conditioning compressor
and fan. In this configuration, the thermostat
will turn on the fan immediately on a call for
heat. If you are unsure whether your system
requires the thermostat to control the fan,
contact your furnace/air conditioning system
manufacturer or a qualified heating/air
conditioning service person.
Your new thermostat has an Installer menu,
which allows you to customize the thermostat
to meet your requirements.
(The thermostat also has a User menu and a
Keypad Lockout menu; these menus are
explained further in the Operating Instructions.)
The menu settings can be changed at any time
to meet system or personal requirements.
ENTERING THE CONFIGURATION
MENUS
After properly wiring the thermostat, turn on
power to the system. Momentarily press
PROGRAM RUN to make certain the
thermostat is in the run program mode, then
press TIME FWD and TIME BACK at the
same time to enter the User Configuration
menu. When the display changes to the first
item in the configuration menu, release the
buttons. Then press and hold SET TIME and
SET DAY for approximately 3 seconds to
enter the Installer menu. The display will
change to show the first item on the Installer
menu (multi-stage/heat pump selection). Use
the following text, along with the Installer
table on page 5, to guide you through the
menu.
Once in the menu, you set each item to the
or
, then
proper selection using
press TIME FWD to change the display to
the next item or TIME BACK to return to the
previous item.
To exit the menu at any time, press PROGRAM RUN .
MULTI-STAGE/HEAT PUMP MODE.
(Installer table step 1.) Use this item to select
the system type (multi-stage or heat pump).
IF YOU HAVE A HEAT PUMP SYSTEM,
you must select HEAT PUMP here. This
sets up proper default values for most heat
pump systems. This selection also makes
available some additional menu items that
apply only to heat pump systems.
HEAT PUMP COMPRESSOR
CONFIGURATION.
(Installer table step 2; this menu item is
displayed only when heat pump was selected
in step 1.) Use this item to select the number
of heat pump compressors and how they are
connected.
ELECTRIC HEAT FAN
CONFIGURATION.
(Installer table step 3.) This menu item
determines whether fan control will be
4
through the thermostat or through the heating
system. If you have an electric heat or other
system that REQUIRES the thermostat to
control the fan, set this item ON. This allows
the thermostat to energize the fan immediately on a call for heat. If you are unsure if
the system requires the thermostat to control
the fan, contact the equipment manufacturer
or a qualified heating and air conditioning
service person. If your system controls fan
operation (as with most fossil fuel systems),
set this item to OFF. Note that with heat
pump systems, the fan always cycles with the
compressor.
SET CYCLE HEAT, COOL, AUX
(ANTICIPATION).
(Installer table steps 4 through 6; step 6 is for
heat pump only). These items allow the cycle
times in heating, cooling and auxiliary (heat
pump systems only) to be increased or
decreased. The factory set values can be
adjusted higher for longer cycles or lower for
shorter cycles.
NOTE: Some manufacturers still instruct you
to set the anticipator to the current draw of
the equipment. That instruction applies only
to mercury bulb or mechanical thermostats; it
does not apply to this digital thermostat. As
configured at the factory, this thermostat will
maintain an accurate temperature. No further
adjustment is necessary, although you can
use these menu items to customize the
performance of the thermostat to your
requirements.
The adjustment range for HEATING is from
(Continued on page 6)
INSTALLER TABLE
NOTE: You must be in the User
Configuration Menu to enter the
Installer Menu. Press TIME FWD
and TIME BACK at same time.
Step
Press Button(s)
Displayed (Factory Default)
Press
or
to select:
1
SET TIME
and SET DAY
(hold for approx.
3 seconds)
MLTI STG
HEAT PUMP
2
TIME FWD
(Heat Pump ONLY)
HEAT PUMP
(1)
COMMENTS
See
Page
Selects type of system. Selecting HEAT PUMP
makes additional menu items for heat pump
system available.
4
2 or 3
Selects:
1. one compressor on Y1.
2. two compressors on Y1, Y2.
3. one compressor on W1.
4
Fan cycles with call for heat if ON. Fan always
cycles with pump stages.
4
3
TIME
FWD
ELECT HEAT FAN
(ON)
OFF
4
TIME
FWD
SET CYCLE HEAT
(5 for multi-stage
13 for heat pump)
1 to 40 for multi-stage
9 to 40 for heat pump
Selects HEAT anticipation adjustment.
4
5
TIME
FWD
SET CYCLE COOL
(13)
9 to 40
Selects COOL anticipation adjustment.
4
SET CYCLE AUX
(06)
1 to 40
Selects AUXILIARY stage anticipation adjustment.
(Heat Pump ONLY)
4
Selects time delay for COOL fan OFF.
6
6
TIME FWD
(Heat Pump ONLY)
7
TIME
FWD
COOL FAN DELAY OFF
(00)
0 to 127 seconds
8
TIME
FWD
FAN DELAY ON
(01)
1 to 30 seconds
Selects time delay for fan ON. Applies only to
compressor stages for heat pump or COOL.
6
9
TIME
FWD
HEAT FAN DELAY OFF
(00)
0 to 127 seconds
Selects time delay for HEAT fan OFF only when
ELECT HEAT FAN (Step 3) is ON.
6
PUMP
(ON)
OFF
6
COMP LOCK
(OFF)
ON
Fossil Fuel Kit Alternative option. Turns compressor
OFF if Auxiliary is ON for longer than one minute.
(Heat Pump 1 & 2)
Selects compressor short-cycle protection enabled
or OFF.*
ECON
(OFF)
ON
Economizer option. Long Y1 cycles for cooling
with outdoor air.
6
6
10
TIME FWD
(Heat Pump ONLY)
11
TIME
FWD
12
TIME
FWD
13
TIME
FWD
HEAT-OFF-COOL-AUTO
or
HEAT-EMER-OFF-COOLAUTO (for heat pumps)
HEAT-OFF-COOL
or
HEAT-EMER-OFF-COOL
(for heat pumps)
14
TIME
FWD
REMT SEN A
(OFF)
ON
Allows selection of HEAT and COOL or HEAT,
COOL and AUTO with SYSTEM button.
(EMER appears in sequence after HEAT if HEAT
PUMP is selected.)
Selects Remote Sensor A (connected to SA) if ON.
15
TIME
FWD
REMT SEN b
(OFF)
ON
Selects Remote Sensor B (connected to SB) if ON.
6
16
TIME
FWD
REMT SEN C
(OFF)
ON
Selects Remote Sensor C (connected to SC) if ON.
6
17
TIME
FWD
STAT SEN L
(ON)
OFF
When OFF, disables local sensor if a remote sensor
is enabled.
7
PROGRAM
Returns to normal operation.
RUN
* NOTE: COMP LOCK OFF permanently
defeats compressor lockout. You must turn
this selection ON if you do not have a
system that already provides compressor
short-cycle protection. Please see “Lockout
Bypass Option” to temporarily override
compressor lockout.
5
6
6
1 to 40 (9 to 40 for heat pump). The factory
preset is 5 (13 for heat pump). The adjustment range for COOLING is from 9 to 40.
The factory preset is 12 (13 for heat pump).
The cooling will not go below 9 because
compressors require a longer cycle. The
adjustment range for AUXILIARY (heat
pump only) is from 1 to 40. The factory
preset is 6.
shuts off just as the warm air is exhausted. If
this timing is set too long the fan may begin
blowing cool air before it shuts off. Shortening the fan-off delay will prevent this.
PUMP (FOSSIL FUEL KIT ALTERNATIVE).
The chart below shows how this adjustment
range affects thermostat performance.
PROGRAMMABLE COOL FAN-OFF
AND FAN-ON DELAY.
(Installer table steps 7 and 8.) These items
allow a selection of 0 to 127 seconds of fanoff delay after the thermostat has satisfied the
call for cool, or a fan-on delay of 1 to 30
seconds on a call for cool (or heat pump
compressor activation).
The fan-off delay allows the fan to continue
running after the compressor has shut off.
This distributes the cool air that would
otherwise stay trapped in the air conditioning
coils through the ducts. Ideally the timing
would be set so the fan shuts off just as the
cool air is exhausted. If this timing is set too
long the fan may begin blowing warm air
before it shuts off. Shortening the fan-off
delay will prevent this.
A short delay to allow the A-coil to cool
off (or warm up in heat pump) before the
fan turns on may be preferred. This also
allows the compressor and the fan to come
on at slightly different times, which allows
full power to the compressor on start up.
Recommended setting for fan-on delay is
10 seconds or less. A system that does not
have a high head pressure cutout should
have a delay of 10 seconds or less.
(Installer table step 10; heat pump only) This
item controls heat pump compressor
operation with a fossil fuel auxiliary. This
menu item may eliminate the need for a
separate fossil fuel kit, although we recommend that you consult the heat pump system
manufacturer before using this feature
instead of a kit. This item will allow the
thermostat to turn the heat pump compressor
off if the auxiliary is on for more than one
minute, to prevent compressor head pressure
from getting too high. To use this feature
instead of a kit, select PUMP OFF.
COMPRESSOR LOCKOUT.
(Installer table step 11). This thermostat is
capable of protecting the system against
premature compressor failure by “locking
out” the compressor for at least five minutes
after each cycle. When the thermostat is in
compressor lockout, the word COOL will
flash on the display. With heat pump
systems, the word HEAT will flash if the
lockout occurs during a heat cycle. During
this period, the compressor will not be
energized.
Lockout Bypass Option
FOR QUALIFIED SERVICE TECHNICIANS’ USE ONLY.
HOMEOWNERS SHOULD NOT USE
THIS FEATURE DUE TO POSSIBILITY OF EQUIPMENT OR PROPERTY DAMAGE, OR PERSONAL
INJURY.
PROGRAMMABLE HEAT FAN-OFF
DELAY.
COMPRESSOR SHORT TERM CYCLE
PROTECTION
(Installer table step 9.) This item allows a
selection of 0 to 127 seconds of fan-off delay
after the thermostat has satisfied the call for
heat if ELECT HEAT FAN (Step 3) is
selected ON.
The fan-off delay allows the fan to continue
running after the burner, heating element,
etc. has shut off. This distributes the heat that
would otherwise stay trapped in the ducts.
Ideally the timing would be set so the fan
If this thermostat has been configured to
provide short-cycle protection, during the
5-minute lockout period the thermostat
will lock out the compressor to allow
head pressure to stabilize. To override
this feature for one cycle while testing
thermostat operation, press SET TIME
and SET DAY buttons at the same time.
If the system has short-cycle protection, this
item should not need to be enabled. However, if your system does not have shortcycle protection, turn COMP LOCK ON.
This will protect the compressor from shortcycling and potential premature compressor
failure.
Note that COMP LOCK OFF permanently
disables compressor lockout. If you need to
temporarily disable compressor lockout,
please see Lockout Bypass Option.
ECONOMIZER FEATURE.
(Installer table step 12). This item allows
longer Y1 cycles for cooling with outdoor
air.
DISABLING AUTOMATIC
CHANGEOVER MODE.
(Installer table step 13). This thermostat, as
configured at the factory, provides automatic
changeover, which allows the thermostat to
switch between heating and cooling to
maintain temperature. In this configuration,
when you press the SYSTEM button, the
thermostat will go through HEAT-OFFCOOL-AUTO modes (HEAT-EMER-OFFCOOL-AUTO for heat pumps). Select
HEAT(-EMER)-OFF-COOL to disable the
automatic changeover feature.
OPTIONAL REMOTE TEMPERATURE SENSE.
(Installer table steps 14 through 16). Up to
three remote sensors (part # F145-1328) can
be attached to this thermostat to sense indoor
temperature at locations away from the
thermostat. Each sensor may be located as
far as 200 feet away from the thermostat.
This is an excellent feature if the thermostat
is in a poor location for sensing temperature
or if you want to install the thermostat in a
separate room to prevent tampering. (Refer
to the installation instructions included with
the remote sensor for proper installation and
wiring.) After installing and connecting the
remote sensor(s) to the thermostat, use these
menu items to enable each remote indoor
temperature sensor (A, b and/or C). Note that
if SENSOR A, b or C are set to ON in the
menu, but no sensor is installed, or if the
sensor is not functioning, when you exit the
menu, CHECK STAT SYSTEM will be
(Continued on page 7)
HEATING
Anticipation Value Cycle Length
COOLING
Differential Temperature Cycle Length Differential Temperature
1–8
Shorter
0.4–0.6°F (0.2–0.3°C)
N/A
N/A
9–20
Longer
0.6–1.0°F (0.3–0.6°C)
Shorter
0.6–1.0°F (0.3–0.6°C)
21–40
Hydronic
1.0–1.6°F (0.6–0.9°C)
Longer
1.0–1.6°F (0.6–0.9°C)
These numbers are approximate and represent operation with a typical system. Actual temperature differentials and
run times may vary widely based on your building and equipment, as well as outdoor temperature conditions.
6
displayed. To correct this, check for proper
remote sensor installation and wiring. If
necessary, return to the menu and be sure that
the remote sensor items are set correctly.
The temperature at each remote sensor can
be displayed by pressing the light button
twice within one second with the thermostat
in program run or hold mode. Temperatures
at the outdoor and indoor remote sensors will
be displayed with subsequent presses of the
light button in the following order (if
connected): outdoor sensor, sensor L, A, b, C.
(Installer table step 17). If you wish to sense
indoor temperature using ONLY the remote
sensor(s), use this menu item to disable the
temperature sensor in the thermostat
(designated as the Local sensor).
When operating with remote sensor(s), the
thermostat will calculate an average of the
sensed temperatures in all enabled sensor
locations (A, b, C and/or L), then display the
average temperature as the room temperature. During programming, you can also
assign each enabled sensor different
priorities during different program periods.
This allows the system to maintain a
comfortable environment by giving higher
priority to occupied locations. At the same
time, efficient system operation is enhanced
by giving lower priority to unoccupied
locations. For detailed instructions on this
feature, see the Operating Instructions.
After using the Installer menu to properly
configure the thermostat for your system,
press PROGRAM RUN .
OUTDOOR TEMPERATURE
SENSE.
This thermostat can also display outdoor
temperature, if you install an outdoor remote
sensor with an outdoor temperature sensor
probe (F145-1378). Refer to the remote
sensor installation instructions for proper
installation and wiring. Refer to the Operating Instructions to enable this feature and
display outdoor temperature on the thermostat.
OPTIONAL ACTIVATE RUN PRG
BY TELEPHONE
With the optional X-10 Telephone Responder
(Model TR551, Radio Shack catalog RSU#
10037778) and Universal Low Voltage
Module (UM506, Radio Shack catalog RSU#
10037752) installed, you can make a
telephone call to run your program if the
thermostat has been set to Hold or Vacation
Hold. Figure 3 shows typical wiring
connections for installing the X-10 equipment. The switch on the Universal Low
Voltage module must be set to the “Momentary” position.
This option must be enabled on the User
menu (see Operating Instructions).
PH
R
4
1
2
1
2
3
4
5
Thermostat terminals
X-10 Universal Low Voltage Module
X-10 Telephone Responder Module
To 115 VAC power source
To telephone line
4
1
3
C
5
Figure 3. Optional X-10 connection
CHECK THERMOSTAT OPERATION
FAN OPERATION
COOLING SYSTEM
If your system does not have a G terminal
connection, skip to “Heating System”
section.
1. Turn power on to the system.
2. Press PROGRAM
RUN
.
3. Press FAN until FAN ON is displayed.
The fan should begin to operate.
4. Press FAN until FAN AUTO is
displayed. The fan should stop operating.
HEATING SYSTEM
1. Press PROGRAM
RUN
.
2. Press SYSTEM until HEAT is displayed. If
the heating system has a standing pilot,
ensure that it is lit.
3. Press
to adjust thermostat setting
above room temperature. The heating system
should begin to operate.
! CAUTION
To prevent compressor and/or property
damage, if the outdoor temperature is
below 50°F (10°C), DO NOT operate the
cooling system.
1. Press PROGRAM
2. Press
SYSTEM
RUN
.
until COOL is displayed.
3. Press
to adjust thermostat setting
below room temperature. The fan should
come on (after the fan-on delay time, if any),
followed by cold air circulation.
to adjust temperature setting
4. Press
above room temperature. The cooling system
should stop operating, and the fan should
stop running (after the fan-off delay time, if
any).
to adjust temperature below
4. Press
room temperature. The heating system
should stop operating.
7
MULTI-STAGE/HEAT PUMP
AUXILIARY OPERATION TEST
Follow these steps to energize all stages of
heat or cool to permit system checks during
installation.
HEAT: Press
to raise temperature
setting to 99°F, then hold for five seconds.
The second and third stage heat relays will
energize immediately for test purposes. The
LED indicator will glow green for first stage
and yellow for second stage.
COOL: Press
to lower temperature
setting to 45°F, then hold for five seconds.
The second stage cool relay will energize
immediately for test purposes. The LED
indicator will glow green for first stage and
yellow for second stage.
EMERGENCY (heat pump only): Press
SYSTEM to select EMER mode. The LED
indicator will glow red for emergency mode.
A flashing light indicates a malfunction in
the system.
TROUBLESHOOTING
RESET BUTTON
If the thermostat does not respond when keys
are pressed, or the thermostat is not operating
properly, you may use the reset button
located on the back of the thermostat body
(see fig. 2). Thermostat programming and
configuration will not be affected by
pressing the reset button. However, the clock
will need to be reset.
RESETTING THERMOSTAT CONFIGURATION AND PROGRAMMING
The thermostat can be reset back to default
programs and configuration. Removing
power from the thermostat will not reset it,
because the default settings are maintained in
permanent memory. Before resetting the
thermostat, you may want to make note of
the previously selected configuration and
programming. You must reconfigure and
reprogram the thermostat after resetting it
using this method.
WHITE-RODGERS
EMERSON ELECTRIC CO.
9797 REAVIS ROAD
ST. LOUIS, MISSOURI 63123-5398
www.white-rodgers.com
To reset the thermostat, press and release
PROGRAM RUN , then press the FAN ,
buttons at the same
TIME BACK and
time. This will reset the thermostat to factory
default programs and configuration. The
display will momentarily go blank, then all
segments on the display will momentarily be
shown. The thermostat will then go into the
HOLD mode and will maintain factory preset
temperatures.