DS8100A-3002
QUICK REFERENCE GUIDE
DS8100A-3002 QUICK GUIDE
DS8100A-3002
General View:
1
Figure A
1 Laser Beam Output Window
1
7
2
3
4
5
6
Figure B
1 Programming Keypad
5 TX Data LED (Green)
2 Power On LED (Green)
6 Network LED (Red)
3 Phase On LED (Yellow)
7 LCD Display
4 Encoder LED (Yellow)
2
1
Figure C
1 Lonworks 17-pin Male Connector
2 Lonworks 17-pin Female Connector
For further details on product installation, see the complete Reference Manual available on the
configuration CD-ROM included with this product.
NOTE
2
DS8100A-3002 QUICK GUIDE
Technical Features:
ELECTRICAL FEATURES
Supply Voltage
Power Consumption
Communication Interfaces
OPTICAL FEATURES
Light Receiver
Safety Class
Wavelength
Laser Control
READING FEATURES
Scan Rate
Max. Resolution
Max. Read. Distance
Max. Read. Width
Max. Depth of Field
USER INTERFACE
LCD Display
Keypad
LED Indicators
SOFTWARE FEATURES
Operating Modes
Config. Mode
Parameter Storage
Readable Codes
Code Selection
ENVIRONMENTAL FEATURES
Operating Temperature
Storage Temperature
Humidity
Vibration Resistance:
EN 60068-2-6
Shock Resistance:
EN 60068-2-27
Protection Class
EN 60529
PHYSICAL FEATURES
Dimensions mm (inch)
Weight
20 - 30 Vdc
1.0 to 0.67 A; 20 W typical
1.5 to 1.0 A; 30 W Max. (including startup current)
Auxiliary
Baud Rate
RS232
1200 to 115200
Other
Lonworks
1.25 Mb/s
Avalanche photodiode
630 to 680 nm
Class 2-EN 60825-1; Class II-CDRH
Security system to turn laser off in case of motor slow down
≤ 1000 scans/s
(see reading diagrams)
2 lines by 20 characters LCD
3 keys
Power ON (green)
Phase ON (yellow)
Encoder (yellow)
TX Data (green)
Network (red)
PackTrack™
Genius™ utility program
Non-volatile internal FLASH
Interleaved 2/5
Code 39 standard
Codabar
Code 128
EAN 128
Code 93 (standard & full ASCII)
EAN/UPC
Up to 10 codes during one reading phase
0° to +50 °C (+32 to +122 °F)
20° to +70 °C (-4° to +158 °F)
-90% non condensing
14 mm @ 2 to 10 Hz; 1.5 mm @ 13 to 55 Hz
2 g @ 70 to 200 Hz; 2 hours on each axis
30 g; 11 ms
3 shocks on each axis
IP65*
217 x 173 x 127 (8.54 x 6.79 x 4.98)
5 Kg (11 lbs.)
* IP65 cables and connectors required (CAB-850x or BTK-8500).
3
DS8100A-3002 QUICK GUIDE
Accessories:
NAME
PWO-480
FS-1
FBK-8100
US-8100
GFC-80
GFC-800
S30
PH-1
MEP-543
OEK-2
OEK-1
BTK-8100
BTK-8500
PLL-8000
CAB-8100
CAB-8101
CAB-8102
CAB-8105
CAB-8501
CAB-8502
CAB-8505
Datalogic WebSentinel-005
Datalogic WebSentinel-010
Datalogic WebSentinel-020
Datalogic WebSentinel-032
Datalogic WebSentinel-064
Datalogic WebSentinel-128
Datalogic WebSentinel-256
Description
Power and Connect System 480W
Frame Shaper (8 pcs)
Fast Bracket Kit (2 pcs)
Bracket Kit (10 pcs)
90 Degree Mirror
90 Degree Close Distance Mirror
Photocell Kit
Photocell Kit - PNP
Photocell Kit - NPN
Optical Encoder Kit (10 m cable + spring)
Optical Encoder Kit + 10 m cable
Bus Terminator Kit (5 pcs)
IP65 Terminator Kit (2 pcs)
Optocoupled PLL device
10 wire shielded cable D 9.5 mm – 50 m
17-pin scanner/scanner connection cable 1.2 m
17-pin scanner/scanner connection cable 2.5 m
17-pin scanner/scanner connection cable 5 m
IP65 Cable Fam 8K 1,2 m
IP65 Cable Fam 8K 2,5 m
IP65 Cable Fam 8K 5 m
Supervisor (up to 5 arrays)
Supervisor (up to 10 arrays)
Supervisor (up to 20 arrays)
Supervisor (up to 32 arrays)
Supervisor (up to 64 arrays)
Supervisor (up to 128 arrays)
Supervisor (up to 256 arrays)
Part Number
93ACC1767
93ACC1750
93ACC1130
93ACC1140
93A251020
93A201103
93ACC1782
93ACC1791
93ACC1728
93ACC1770
93ACC1600
93ACC1090
93A051286
93ACC1280
93ACC1120
93A051020
93A051030
93A051040
93A051283
93A051284
93A051285
93A101014
93A101015
93A101016
93A101017
93A101018
93A101019
93A101020
Electrical Connections:
Two 17-pin connectors provide access to the scanner’s local Lonworks network used for both input and output
connections to build a multi-sided or omni-station system.
17-pin Lonworks Connector Pinout
Pin
A1
A2
1
4
Name
GND
VS
CHASSIS
2
n.c.
3
CHASSIS
4
TXAUX
5
SGND
6
RXAUX
7
8
9
10
11
12
13
14
15
VS_I/O
Lon A+
Lon ALon B+
Lon BSYS_I/O
SYS_ENC_I/O
Reserved
Ref_I/O
Function
Supply voltage (negative pin)
Supply voltage 20 to 30 Vdc (positive pin)
Cable shield A - internally connected by
capacitor to chassis
Not connected
Cable shield B - internally connected by
capacitor to chassis
Transmit data of auxiliary RS232
(referred to SGND)
Signal ground (connected to GND)
Receive data of auxiliary RS232
(referred to SGND)
Supply voltage of I/O circuit
Lonworks a line (positive pin)
Lonworks a line (negative pin)
Lonworks b line (positive pin)
Lonworks b line (negative pin)
System signal
System signal
Internally connected
Reference voltage of I/O circuit
1
A1
A2
15
Male - Input
15
A1
1
A2
Female - Output
17-pin Local Lonworks Connectors
DS8100A-3002 QUICK GUIDE
Connectivity:
Host
HUB
ETHERNET
CAB-SC6103
Cable
SC6000
AUX
VAC INPUT
Power/Net
CAB-SC6013
PWO
CAB-SC6003
Extended I/O
LONWORKS
ENCODER
CAB-850x
BTK8500
Bus Return
PS
PS Aux
CAB-850x
CAB-850x
CAB-850x
up to 3
scanners
per
branch
DX8200A-3002
DX8200A-3002
DX8200A-3002
CAB-850x
CAB-850x
BTK8500
Bus Return
CAB-850x
up to 4
scanners per
branch
DS8100A-3002
DS8100A-3002
DS8100A-3002
DS8100A-3002
DS8100A-3002 Typical Layout
Conveyor
SC6000
5
DS8100A-3002 QUICK GUIDE
to Host
ETHERNET
SC6000
VAC INPUT
CAB-SC6103
AUX
Working
Controller
Power/Net
CAB-SC6013
PWO
CAB-SC6003
Extended I/O
LONWORKS
ENCODER
CAB-850x
CAB-850x
CAB-850x
DX8200A-3002
PS
PS Aux
DX8200A-3002
BTK8500
CAB-850x
DS8100A-3002
DS8100A-3002
Redundancy
CAB-PWO 03
to Host
ETHERNET
VAC INPUT
SC6000
Power/Net
CAB-SC6013
PWO
CAB-SC6003
Extended I/O
Protecting
Controller
LONWORKS
ENCODER
CAB-850x
CAB-850x
DX8200A-3002
PS
PS Aux
CAB-850x
DX8200A-3002
DS8100A-3002
Example of Redundant System Layout
6
CAB-850x
BTK8500
DS8100A-3002
DS8100A-3002 QUICK GUIDE
Example of Redundant System
7
DS8100A-3002 QUICK GUIDE
Mechanical Installation:
164
127
[4.98]
5
[6.45]
[0.19]
DS8100A-3002 can be installed to operate in any position. There are 16 screw holes (M6 X 8) on the sides of the
scanner for mounting. The following diagrams give the overall dimensions of the reader standard model and
mounting bracket. They may be used for their installation:
R 15
30
68
[2.66]
50
[1.97]
217
[8.54]
[3.93]
[1.18]
45°
100
47
[1.84]
M6 N°16
164
[0.59]
[6.45]
173
[6.79]
16
R 15 N°4
[0.63]
48
[1.88]
8
100
15
[3.93]
[0.59]
8.5 N°4
[0.33]
45
[1.77]
17.5
mm
inch
DS8100A-3002 Overall Dimensions
WARNING
[3.15]
45°
[0.68]
47
[1.84]
50
[1.97]
68
[2.66]
80
[0.59]
mm
mm
inch
inch
ST-163 Mounting Bracket Overall Dimensions
When installing several scanners, take care to position them correctly so that no laser beam
enters the reading window perpendicularly and at the same level of the output beam of the
other scanners. This condition could occur more frequently for side mounted applications. If
these precautions are not followed, it may occur that the laser of the blinded scanner starts
blinking due to an internal circuit which temporarily turns the laser off when detecting a power
anomaly. To resolve this problem, it is sufficient to slightly change the inclination and position
of one of the two scanners involved.
DS8100A-3002 QUICK GUIDE
Reading Diagrams:
Note: (0,0) is the center of the laser beam output window.
DS8100A-3002 – 0.50 mm/20 mils
CONDITIONS
Code = Interleaved 2/5 or Code 39
PCS = 0.90
“Pitch“ angle = 0°
“Skew“ angle = 10°
“Tilt“ angle = 0°
24
60
20
50
16
40
12
30
8
20
4
10
0
0
-4
-10
-8
-20
-12
-30
-16
-40
-20
-50
-24
0
15
24
32
40
48
56
64
0
40
60
80
100
120
140
160
(in)
(cm)
-60
(in) (cm)
Safety Precautions:
3
2
1
Figure A
1 Laser Safety Label
3 Identification Label
2 Warning and Device Class Label
The scanner is classified as a Class 2 laser product according to EN60825-1 regulations and as a Class II laser
product according to CDRH regulations.
Disconnect the power supply when opening the device during maintenance or installation to avoid exposure to
hazardous laser light.
There is a safety device, which allows the laser to be switched on only if the motor is rotating above the threshold
for its correct scanning speed.
9
DS8100A-3002 QUICK GUIDE
The laser beam can be switched off through a software command (see also the Genius™ Help On-Line).
AVOID EXPOSURE
LASER LIGHT IS EMITTED
FROM THIS APERTURE
CAUTION-CLASS 3B
LASER LIGHT
WHEN OPEN
AVOID
EXPOSURE TO BEAM
AVOID EXPOSURE
LASER RADIATION IS EMITTED FROM THIS APERTURE
Laser Safety Label
DATALOGIC S.P.A. Via Candini, 2
40012 Calderara di Reno - Bologna - Italy
LASER LIGHT
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
MAXIMUM OUTPUT RADIATION 1 mW
EMITTED WAVELENGTH 630~680 nm
TO EN 60825-1:2001
Manufactured
Volt
Model No.
Amp.
Serial No.
This product conforms to the applicable requirements
of 21CFR1040 at the date of manufacture.
Warning and Device Class Label
Device Identification Label
The laser diodes used in this device are classified as Class 3B laser products according to EN 60825-1
regulations and as Class IIIb laser products according to CDRH regulations. Any violation of the optic parts in
particular can cause radiation up to the maximum level of the laser diode (30 mW at 630~680 nm).
Power Supply
This product is intended to be installed by Qualified Personnel only.
This scanner is intended to be supplied by either a UL Listed power supply marked 'Class 2' or 'LPS', output rated
20 - 30 V dc, minimum 1.5 A or by a UL Listed computer with LPS outputs.
DS8100A-3002 must be supplied by a Class II Power Supply Unit conforming to the EN 60950 safety regulation.
Patents:
This product is covered by one or more of the following patents.
U.S. patents: Re. 36,251; 5,483,051; 5,992,740; 6,177,979 B1; 6,347,740 B1; 6,394,352 B1; 6,443,360 B1;
6,527,184 B1; 6,629,639 B2; 6,688,524 B1; 6,742,710 B2; 7,161,685 B1; 5,028,772; 5,124,538; 5,466,921;
5,548,107; 6,206,289 B1; 6,669,091 B2; 7,000,838 B2.
European patents: 652,530 B1; 789,315 B1; 851,376 B1; 926,615 B1; 959,426 B9; 1,363,228 B1.
Japanese patents: 3,793,585; 4,033,958.
Additional patents pending.
10
DECLARATION OF CONFORMITY
08
Datalogic Automation S.r.l.
Via S. Vitalino 13
40012 - Lippo di Calderara
Bologna - Italy
dichiara che
declares that the
déclare que le
bescheinigt, daß das Gerät
declare que el
e tutti i suoi modelli
and all its models
et tous ses modèles
und seine Modelle
y todos sus modelos
DS8100A-XXXX Laser Scanner
sono conformi alle Direttive del Consiglio Europeo sottoelencate:
are in conformity with the requirements of the European Council Directives listed below:
sont conformes aux spécifications des Directives de l'Union Européenne ci-dessous:
der nachstehend angeführten Direktiven des Europäischen Rats:
cumple con los requisitos de las Directivas del Consejo Europeo, según la lista siguiente:
89/336/EEC EMC Directive
e
and
et
und
y
92/31/EEC, 93/68/EEC
emendamenti successivi
further amendments
ses successifs amendements
späteren Abänderungen
succesivas enmiendas
2006/95/EC Low Voltage Directive
Basate sulle legislazioni degli Stati membri in relazione alla compatibilità elettromagnetica ed alla sicurezza dei prodotti.
On the approximation of the laws of Member States relating to electromagnetic compatibility and product safety.
Basée sur la législation des Etats membres relative à la compatibilité électromagnétique et à la sécurité des produits.
Über die Annäherung der Gesetze der Mitgliedsstaaten in bezug auf elektromagnetische Verträglichkeit und Produktsicherheit
entsprechen.
Basado en la aproximación de las leyes de los Países Miembros respecto a la compatibilidad electromagnética y las Medidas
de seguridad relativas al producto.
Questa dichiarazione è basata sulla conformità dei prodotti alle norme seguenti:
This declaration is based upon compliance of the products to the following standards:
Cette déclaration repose sur la conformité des produits aux normes suivantes:
Diese Erklärung basiert darauf, daß das Produkt den folgenden Normen entspricht:
Esta declaración se basa en el cumplimiento de los productos con las siguientes normas:
EN 55022 (Class A ITE), September 1998:
INFORMATION TECHNOLOGY EQUIPMENT
RADIO DISTURBANCE CHARACTERISTICS
LIMITS AND METHODS OF MEASUREMENTS
EN 61000-6-2, September 2005:
ELECTROMAGNETIC COMPATIBILITY (EMC)
PART 6-2: GENERIC STANDARDS - IMMUNITY FOR INDUSTRIAL ENVIRONMENTS
EN 60950-1, December 2001:
EN 60950-1/A11, April 2004:
INFORMATION TECHNOLOGY EQUIPMENT - SAFETY PART 1 : GENERAL REQUIREMENTS
EN 60825-1, March 1994:
EN 60825-1/A1, July 1996:
EN 60825-1/A2, March 2001:
SAFETY OF LASER PRODUCTS PART 1 : EQUIPMENT CLASSIFICATION, REQUIREMENTS AND USER'S GUIDE
Lippo di Calderara, January 29th, 2008
Lorenzo Girotti
Product & Process Quality Manager
821001262 (Rev. B)