Emerson CURVA SKY CF152BS00 Owner`s manual

BP7407 44" &
52" Curva Sky
1/11/10
9:54 PM
Page 1
READ AND SAVE THESE INSTRUCTIONS
CURVA SKY™
44” & 52” Damp & Wet
Location Snugger Ceiling Fan
Owner's Manual
44” Model Numbers
for Damp Locations
52” Model Numbers
for Damp Locations
CF144BS00
CF152BS00
Brushed Steel
Brushed Steel
CF144CRM00
CF152CRM00
Chrome
Chrome
44” Model Numbers
for Wet Locations
52” Model Numbers
for Wet Locations
CF144WW00
CF152WW00
Appliance White
Appliance White
CF144ORB00
CF152ORB00
Oil Rubbed Bronze
Oil Rubbed Bronze
Net Weight:
Part No. F40BP74070000
18.5
Lbs.
Net Weight:
19.4
Lbs.
Form No. BP7407
UL Model No.: CF144 & CF152
BP7407 44" &
52" Curva Sky
1/11/10
!
9:54 PM
Page 2
WARNING
WARNING: To avoid fire, shock, and serious personal injury, follow these
instructions.
Safety Instructions
1. Read your owner’s manual carefully and keep it for future reference.
2. Before servicing or cleaning unit, switch power off at service panel and lock service
panel disconnecting means to prevent power from being switched on accidentally.
When the service disconnecting means cannot be locked, securely fasten a
warning device, such as a tag, to the service panel.
3. Be careful of the fan and blades when cleaning, painting, or working near the fan.
Always turn off the power to the ceiling fan before servicing.
4. Do not put anything into the fan blades while they are turning.
Additional Safety Instructions for Installation
1. To avoid possible shock, be sure electricity is turned off at the fuse box before
wiring, and do not operate fan without blades.
2. The installation is to be in accordance with the National Electrical Code, ANSI/NFPA
70-2008 and Local Codes. Use the National Electrical Code if Local Codes do not
exist. The ceiling fan must be grounded as a precaution against possible electrical
shock. Electrical installation should be made or approved by a licensed electrician.
3. The outlet box and joist must be securely mounted and capable of reliably
supporting at least 50 pounds. Use only U.L. outlet boxes listed as “Acceptable for
Fan Support”, and use the mounting screws provided with the outlet box. Most
outlet boxes commonly used for support of light fixtures are not
acceptable for fan support and may need to be replaced. Consult a qualified
electrician if in doubt.
4. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent
accidental contact with the fan blades.
5. Follow the recommended instructions for the proper method of wiring your ceiling
fan. If you do not know enough about electrical wiring, have your fan installed by a
licensed electrician.
NOTE: This fan is suitable for use with solid-state speed controls.
WARNING: To reduce the risk of fire or electric shock, this fan should only be used
with fan speed control Model No. UC8013G, manufactured by Rhine Electric Co., Ltd.
WARNING: This product is designed to use only those parts supplied with this
product and/or any accessories designated specifically for use with this product by
Emerson Electric Co. Substitution of parts or accessories not designated for use with
this product by Emerson Electric Co. could result in personal injury or
property damage.
WARNING: To reduce the risk of personal injury, do not bend the blade flange when
installing the blade flanges, balancing the blades or cleaning the fan. Do not insert
foreign objects in between rotating fan blades.
WARNING: To reduce the risk of electric shock, this fan must be installed with an
isolating remote control/switch.
DATE CODE:
The date code of this fan may be found on the box, stamped in ink on a white label.
You should record this data above and keep it in a safe place for future use.
2
UL Model No.: CF144 & CF152
BP7407 44" &
52" Curva Sky
1/11/10
9:54 PM
Page 3
THE FAN MODELS CF144BS, CF144CRM, CF152BS & CF152CRM ARE SUITABLE
FOR DAMP LOCATIONS SUCH AS COVERED PORCHES, COVERED PATIOS,
AND COVERED DECKS...ANYWHERE THERE IS A ROOF OVERHEAD.
THE FAN MODELS CF144WW, CF144ORB, CF152WW & CF152ORB ARE
SUITABLE FOR WET LOCATIONS SUCH AS PORCHES, PATIOS, AND DECKS.
This Manual is Designed to Make it as Easy as Possible for You to
Assemble, Install, Operate and Maintain Your Ceiling Fan
Tools Needed for Assembly
Installed Wire Length
Up to 50 ft.
50-100 ft.
One Phillips head screwdriver
One wire stripper
One stepladder
!
Materials
Wiring, outlet box and box connectors
must be of type required by the local code.
The minimum wire would be a 3-conductor
(2-wire with ground) of the following sizes:
Wire Size A.W.G.
14
12
WARNING
Before assembling your ceiling fan, refer
to section on proper method of wiring
your fan (Page 7). If you feel you do not
have enough wiring knowledge or
experience, have your fan installed by a
licensed electrician.
Unpacking Instructions
For your convenience, check-off boxes are provided next to each step. As each
step is completed, place a check mark in the box. This will insure that all steps
have been completed and will be helpful in finding your place should you be
interrupted.
a. Fan motor assembly
!
WARNING
b. One ceiling trim ring
c. One ceiling mounting plate
Do not install or use fan if any part is
d. Three fan blades
damaged or missing. Call Toll-Free:
e. One lower housing
1-800-654-3545
f. One light kit plate
g. One glass shade
!
WARNING
h. One no-light cover plate
i. One 6-speed electronic receiver
This product is designed to use only
those parts supplied with this product
control with parts bag
and/or any accessories designated
j. One 6-speed handheld transmitter
specifically for use with this product by
with wall bracket
Emerson Electric Co. Substitution of
k. Two 50W halogen mini candelabra
parts or accessories not designated for
bulbs
use with this product by Emerson Electric
l. One loose parts bag containing:
Co. could result in personal injury or
1. Three 12 ga. wire connectors
property damage.
2. One spare M5 x 10mm pan head
ceiling cover screw
1. Open carton containing fan. Remove
3. Ten M5 x 16mm flange head
top half of styrofoam unit. Remove
blade screws
parts and check to see that you have
4. One spare M4 x 10mm pan head
received the following parts:
screw for lower housing and
NOTE: If you are uncertain of part
light kit
description, refer to exploded view
5. One balancing kit
illustration.
3
UL Model No.: CF144 & CF152
BP7407 44" &
52" Curva Sky
1/11/10
9:54 PM
A. FAN MOTOR
ASSEMBLY
Page 4
B. CEILING
TRIM RING
E. LOWER
HOUSING
F. LIGHT
KIT PLATE
C. CEILING
MOUNTING PLATE
H. NO-LIGHT
COVER PLATE
D. FAN BLADES (3)
K. 50W MINI CANDELABRA
HALOGEN BULBS
G. GLASS SHADE
I. 6-SPEED
ELECTRONIC
RECEIVER
J. 6-SPEED
HANDHELD
TRANSMITTER
NOTE: Place the parts from the loose
parts bags in a small container to keep
them from being lost.
L. LOOSE
PARTS BAG
PROTECTIVE
PLASTIC BAG
2. Remove the fan motor assembly from
the protective plastic bag. Place all
carton contents on a protective
surface.
4
UL Model No.: CF144 & CF152
BP7407 44" &
52" Curva Sky
1/11/10
9:54 PM
Electrical Requirements
How to Assemble Your
Ceiling Fan
IMPORTANT: Your ceiling fan will not
function properly, and may be
damaged, if used with any wall dimmer
switch or control other than the
Emerson Electric Fan/Light Remote
Control supplied with the fan.
1. Position the fan motor assembly upside
down in preparation for mounting the
three fan blades.
2. Slide blade through blade slot in fan
housing assembly. Mount blade to fan
housing using three M5 x 16mm flange
head blade screws (Figure 1).
Your new ceiling fan will require a
grounded electrical supply line of 120 volts
AC, 60 Hz, 15 amp circuit.
NOTE: Take care not to scratch fan
housing assembly when installing
blades.
The outlet box must be securely anchored
and capable of withstanding a load of at
least 50 pounds.
!
Page 5
WARNING
M5 x 16mm FLANGE
HEAD BLADE SCREWS
(3 per blade)
FAN
HOUSING
FAN
BLADE
To reduce the risk of fire, electric shock,
or personal injury, mount fan to outlet box
marked “Acceptable for Fan Support”,
and use screws supplied with outlet box.
Most outlet boxes commonly used for
support of light fixtures are not
acceptable for fan support and may need
to be replaced. Consult a qualified
electrician if in doubt.
SLIDE FAN BLADE
INTO BLADE
CENTER SLOT
BLADE
SLOT
Figure 1
If your fan is to replace an existing ceiling
light fixture, turn electricity off at the main
fuse or circuit breaker box at this time and
remove the existing light fixture.
!
3. Complete the remaining two blades
installation per the above instructions.
4. Remove one of the three screws in the
motor housing assembly and loosen
the remaining two screws (Figure 2).
5. Attach the lower housing assembly to
the fan motor using the two key slot
holes (Figure 2). Secure the lower
housing assembly by tightening the two
screws. Reinstall the screw that was
previously removed.
WARNING
Turning off wall switch is not sufficient.
To avoid possible electrical shock, be
sure electricity is turned off at the main
fuse or circuit breaker box before wiring.
All wiring must be in accordance with
National and Local codes and the ceiling
fan must be properly grounded as a
precaution against possible electrical
shock.
REMOVE M4 x 10mm
PAN HEAD SCREW
LOWER HOUSING
Ceiling Fan Procedures
General
KEY HOLE
SLOT (2)
Your Emerson ceiling fan comes supplied
with a Fan/Light Remote Control which
consists of a receiver mounted inside the
ceiling cover of the fan motor housing.
This system allows you to regulate your
ceiling fan speed and light intensity.
Figure 2
5
UL Model No.: CF144 & CF152
BP7407 44" &
52" Curva Sky
1/11/10
9:54 PM
6. Remove and retain the wire connectors
from the white and blue wires.
7. Connect the white wire from the ceiling
fan to the white wire of the light kit plate
(Figure 3). Connect the blue wire from
the ceiling fan to the black wire of the
light kit plate. Use wire connectors
(previously
removed)
to
make
connections.
8. Remove one of the three screws in the
lower housing and loosen the
remaining two screws (Figure 3).
Page 6
How to Hang
Your Ceiling Fan
!
WARNING
The fan must be hung with at least 7' of
clearance from floor to blades (Figure 5).
CEILING
LIGHT KIT
BLACK WIRE
AT
LEAST
7'
LIGHT KIT
WHITE WIRE
REMOVE ONE
LOWER HOUSING
SCREW
FAN MOTOR
BLUE WIRE
Figure 5
FAN MOTOR
WHITE WIRE
!
Figure 3
WARNING
The outlet box and joist must be securely
mounted and capable of supporting at
least 50 lbs. Use only a U.L. outlet box
listed as “Acceptable for Fan Support”.
9. Tuck the wires and connectors into the
fan housing. Position the light kit plate
into the fan housing by placing the cut
out notches over the fan housing
dimples (Figure 4).
!
NOTE: Make sure all wires and
connectors are tucked under the light
kit plate and not pinched between light
kit plate and fan housing.
WARNING
To reduce the risk of fire, electric shock,
or personal injury, mount fan to outlet box
marked “Acceptable for Fan Support”,
and use screws supplied with outlet box.
Most outlet boxes commonly used for
support of light fixtures are not
acceptable for fan support and may need
to be replaced. Consult a qualified
electrician if in doubt.
10. Attach the light kit plate assembly to
the lower housing using two key slot
holes (Figure 4). Secure the light kit
plate assembly by tightening the two
screws. Reinstall the screw that was
previously removed.
1. Disconnect electrical power to the branch
circuit at the circuit breaker or fuse box
before attempting to install the ceiling fan
mounting plate on the outlet box.
LOWER HOUSING
KEY HOLE SLOT (2)
REMOVE M4 x 10mm
PAN HEAD SCREW
CUT OUT
NOTCHES
!
WARNING
Turning off wall switch is not sufficient.
To avoid possible electrical shock, be sure
electricity is turned off at the main fuse or
circuit breaker box before wiring. All wiring
must be in accordance with National and
Local codes and the ceiling fan must be
properly grounded as a precaution against
possible electrical shock.
DIMPLES
Figure 4
FLOOR
LIGHT KIT
PLATE
6
UL Model No.: CF144 & CF152
BP7407 44" &
52" Curva Sky
1/11/10
9:54 PM
2. Pull the electrical supply black, white
and ground wires through the center
opening of the ceiling mounting plate
before securing the plate to the outlet
box (Figure 6).
How to Wire
Your Ceiling Fan
If you feel that you do not have enough
electrical
wiring
knowledge
or
experience, have your fan installed by a
licensed electrician.
3. Position the ceiling mounting plate onto
the outlet box and secure using the two
outlet box screws, supplied with outlet
box (Figure 6).
!
OUTLET
BOX
CEILING
MOUNTING
PLATE HOOK
CAUTION: To reduce the risk of electrical
shock, disconnect the electrical supply
circuit before installing the fan, light kit
or receiver.
Figure 6
4. Slide the ceiling trim ring over the fan
motor assembly and let it rest on the
motor assembly (Figure 7).
NOTE: Make all wiring connections
using wire connectors (supplied). Make
sure that all connections are tight,
including ground, and that no bare wire
is visible at the wire connectors, except
for the ground wire.
1. Position the receiver into the fan motor
housing as shown in Figure 9.
2. Refer to Figures 9 and 10 to connect
the receiver wires to the supply wires
and the fan motor wires using the wire
connectors supplied with the fan as
follows:
a. Securely connect the green grounding
wire from the ceiling mounting plate to
the supply green grounding conductor
(this may be a bare wire or a wire with
green insulation).
b. Securely connect the supply white
(neutral) wire to the receiver white
(AC IN N)/(TO MOTOR N) wire and
white (neutral) fan wire.
c. Securely connect the supply black wire
to the receiver black/white (AC IN L)
wire.
d. Securely connect the fan motor black
wire to the receiver black (TO MOTOR
L) wire.
e. Securely connect the fan motor blue
wire to the receiver blue (FOR
BOTTOM LIGHT) wire.
FAN MOTOR
ASSEMBLY
CEILING
TRIM
RING
Figure 7
5. Place the motor assembly onto the
ceiling mounting plate hook during
wiring fan motor assembly to outlet box
(Figure 8).
CEILING
MOUNTING
PLATE
WARNING
Turning off wall switch is not sufficient.
To avoid possible electrical shock, be
sure electricity is turned off at the main
fuse box before wiring. All wiring must be
in accordance with National and Local
codes and the ceiling fan must be
properly grounded as a precaution
against possible electrical shock.
CEILING
MOUNTING
PLATE
OUTLET BOX
SCREWS (2)
Page 7
HOOK
FAN MOTOR
ASSEMBLY
Figure 8
7
UL Model No.: CF144 & CF152
BP7407 44" &
52" Curva Sky
!
1/11/10
9:54 PM
Page 8
WARNING
!
Check to see that all connections are
tight, including ground, and that no bare
wire is visible at the wire connectors,
except for the ground wire. Do not
operate fan until blades are in place.
Noise and fan damage could result.
To avoid possible fire or shock, make
sure that the electrical wires are
completely inside the outlet box and
not pinched between the ceiling
mounting plate and the fan motor
housing assembly.
SUPPLY & CEILING MOUNTING
PLATE GREEN WIRES
SUPPLY,
RECEIVER & FAN
WHITE WIRES
SUPPLY
BLACK WIRE
RECEIVER
BLACK/WHITE
WIRE
FAN &
RECEIVER
BLUE WIRES
FAN BLACK
WIRE
4. Remove one of the four screws in the
ceiling mounting plate and loosen the
remaining three screws (Figure 11).
5. Unhook the fan motor housing from the
ceiling mounting plate hook and lift the
fan motor housing assembly up to the
ceiling mounting plate. Align and
engage the motor assembly slots with
the three screw heads previously
loosened by rotating the fan motor
housing assembly clockwise. Install the
previously removed M5 x 10mm screw
and secure the assembly to the plate
(Figure 11). Completely tighten all four
screws.
RECEIVER BLACK
WIRE
ANTENNA
WIRE
RECEIVER
Figure 9
RECEIVER
WHITE
RECEIVER
WIRE
BLACK RECEIVER
WIRE
BLACK/WHITE
RECEIVER WIRE
WHITE FAN WIRE
WARNING
BLACK SUPPLY
WIRE
CEILING
MOUNTING PLATE
WHITE
SUPPLY
WIRE
BLUE RECEIVER
WIRE
BLUE FAN WIRE
BLACK FAN WIRE
Figure 11
M5 x 10mm PAN
HEAD CEILING
COVER SCREWS
FAN MOTOR
HOUSING
ASSEMBLY
6. Position the ceiling trim ring over each
of the protruding ceiling cover screw
heads and rotate the ceiling trim ring
clockwise to secure (Figure 12).
Figure 10
CEILING COVER SCREW
HEADS (4)
3. After connections have been made,
turn leads upward and carefully push
leads into the outlet box, with the white
and green leads on one side of the
outlet box and the black and blue leads
on the other inside of the outlet box.
CEILING
TRIM RING
FAN MOTOR
HOUSING
ASSEMBLY
Figure 12
8
UL Model No.: CF144 & CF152
BP7407 44" &
52" Curva Sky
1/11/10
9:54 PM
How to Assemble Your
Light Kit Glass Shade
How to Assemble Your
No Light Cover Plate
1. Screw in two 50-watt (maximum)
halogen mini candelabra base bulbs in
the light kit plate sockets (Figure 13).
50-WATT (maximum)
HALOGEN MINI
CANDELABRA BASE
BULBS (2)
Page 9
!
WARNING
Do not install any light bulbs into the
light kit plate if using the cover plate.
Installation of light bulbs when using
the cover plate could result in fire,
shock and serious personal injury.
1. Place the cover plate onto the lower
housing aligning the three flat areas on
the top flange of the cover plate with
the three pins on the inside of the fan
motor housing assembly (Figure 15).
Then turn the cover plate clockwise
until it stops turning.
LIGHT KIT PLATE
SOCKETS (2)
2. Your cover plate is now installed
Figure 13
DO NOT INSTALL LIGHT BULBS
WHEN USING THE COVER PLATE
2. Place the glass shade into the opening
in the fan motor housing assembly,
aligning the three flat areas on the top
edge of the glass with the three raised
dimples on the fan motor housing
assembly and turn the glass shade
clockwise until it stops (Figure 14).
NOTE: periodically check that the glass
shade is seated fully clockwise in the
fan motor housing assembly.
DIMPLES (3)
FLAT AREA (3)
COVER
PLATE
Figure 15
DIMPLES (3)
FLAT AREA (3)
GLASS
BOWL
Figure 14
9
UL Model No.: CF144 & CF152
BP7407 44" &
52" Curva Sky
1/11/10
9:54 PM
REMOTE CONTROL
PROCEDURES
Page 10
Installation of Battery
1. Remove the battery cover by pressing
firmly below the arrow and sliding the
cover off the control (Figure 16).
General
Your Emerson Ceiling Fan/Light Remote
Control consists of hand-held transmitter
and a receiver which is mounted under the
fan ceiling cover. The remote control is
designed to separately control your ceiling
fan speed and light intensity.
The remote control transmitter is powered
by two AAA alkaline batteries (included).
To prevent possible damage if the
batteries should leak, be sure to remove
the batteries when the control is not to be
used for an extended period of time.
Code switches in the transmitter and
receiver may be set in 32 different
positions. If your fan and light go on and
off without using your control, you may be
getting interference from other remote
units such as garage door openers, car
alarms or security systems. To remedy this
situations, simply change the combination
code in your transmitter and receiver.
2. Install two AAA alkaline batteries and
reinstall the battery cover.
Preset Memory Feature
A storage bracket is provided for holding
your remote control when not in use. If you
desire to use the bracket, install it on a
wall that is away from excess heat or
humidity (Figure 17).
REMOTE CONTROL
LEVERS
ON
1
2
3
4 5
I
TWO AAA
BATTERIES
CODE
SWITCHES
BATTERY
COMPARTMENT
COVER
SR600 REMOTE
CONTROL
Figure 16
Installation of Storage
Bracket for
Remote Control
Your Emerson receiver is equipped with a
preset memory feature. If the AC supply to
the receiver is powered through a wall
switch, when the switch is turned OFF, the
control will remember the light intensity
and fan speed. When the switch is turned
back ON the light and fan will resume
operation as they were prior to the switch
being turned OFF.
TO INSTALL BRACKET TO WALL:
SLIDE THE COVER UP TO EXPOSE THE SCREW
HOLES FOR INSTALLATION
COVER
WALL
BRACKET
SCREW
HOLES (2)
Figure 17
10
UL Model No.: CF144 & CF152
BP7407 44" &
52" Curva Sky
1/11/10
9:54 PM
Page 11
Setting Operating
Frequency of
Remote Control
Your remote control has code switches
which must be set in one of 32 possible
code combinations (Figure 16). The five
levers (numbered 1, 2, 3, 4, and 5) on the
switches are factory-set in the ON (up)
position. Change the switch settings as
follows (Figure 18):
1. Slide the five switch levers in the
remote control to your choice of ON
(up) or down positions. Use a ball-point
pen or small screwdriver and slide the
levers firmly up or down.
2. When power is restored, push and hold
the fan OFF button (
) for 3 to 5
seconds to set the code in the receiver.
3. If airflow is desired in the opposite
direction, press the ( ) button on the
remote control. The fan must be
operating at any speed for the reverse
button to function. The blades will turn
in the opposite direction and reverse
the airflow.
4. To set the desired fan speed, press the
( ) button to decrease the speed and
the (
) to increase the speed. The
LED display will light up to indicate the
new speed selected.
5. To turn the downlight on, press and
release the (
) button. The light will
turn on at the light intensity previously
selected.
6. To vary the intensity of the light, hold
the (
) button down until the desired
light intensity is reached, then release
the button.
Figure 18
7. The sixth switch marked ON and I is for
dimming control of lights: Set switch to
ON to allow for dimming of the lights.
Set switch to I for no dimming of the
lights such as for fluorescent bulbs.
11
UL Model No.: CF144 & CF152
BP7407 44" &
52" Curva Sky
1/11/10
9:54 PM
Page 12
Maintenance
Accessories
IMPORTANT CARE INSTRUCTIONS
for your Ceiling Fan
1. Downrod Extension Kits (see store or
catalog).
2. Ceiling Fan Controls (see store or
catalog).
Periodic cleaning of your new ceiling fan is
the only maintenance that is needed.
When cleaning, use only a soft brush or
lint free cloth to avoid scratching the finish.
!
The use of any other control not
specifically approved for this fan could
result in fire, shock and personal injury.
Abrasive cleaning agents are not required
and should be avoided to prevent damage
to finish.
!
WARNING
!
WARNING
WARNING
This product is designed to use only
those parts supplied with this product
and/or any accessories designated
specifically for use with this product by
Emerson Electric Co. Substitution of
parts or accessories not designated for
use with this product by Emerson Electric
Co. could result in personal injury or
property damage.
Do not use water when cleaning your
ceiling fan. It could damage the motor or
the blades and create the possibility of an
electrical shock.
INSTRUCTION TO THE USER (if device contains a digital device)
This equipment has been tested and found to comply with the limits for a class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV technician for help.
This equipment has been certified to comply with the limits for a class B computing device,
pursuant to FCC Rules. In order to maintain compliance with FCC regulations, shielded cables
must be used with this equipment. Operation with non-approved equipment or unshielded
cables is likely to result in interference to radio and TV reception. The user is cautioned that
changes and modifications made to the equipment without the approval of manufacturer could
void the user’s authority to operate this equipment.
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
12
UL Model No.: CF144 & CF152
BP7407 44" &
52" Curva Sky
1/11/10
9:54 PM
Page 13
Remote Control Trouble Shooting
Fan/Light Fails to Operate
Short Range
• Check that the speed switch on the
fan is set to HIGH (....) speed.
• Check that the light switch is on.
• Check that the battery is good
(red indicator light should light when
any button is pressed).
• Check that the receiver is wired
properly.
• Check that code switches in the
remote control and receiver are set in
the same position.
• If the remote control operates the fan
when close to it, but does not operate
it at a distance of 40 feet, try placing
the antenna wire outside of the ceiling
cover.
WARNING: FOR YOUR OWN SAFETY TURN OFF POWER AT FUSE BOX
!
OR CIRCUIT BREAKER BEFORE TROUBLE SHOOTING YOUR FAN.
Ceiling Fan Trouble Shooting
TROUBLE
1. Fan will not
start.
PROBABLE CAUSE
1. Fuse or circuit breaker
blown.
2. Loose power line
connections to the fan.
3. Fan/Light remote control is OFF.
2. Fan sounds
noisy.
1. Blades not attached to fan.
2. Screws securing fan blades
to motor are loose.
3. Fan wobbles
excessively.
1. Screws securing fan blades
to motor are loose.
2. Fan blades are not seated
properly.
3. Fan blades out of balance.
13
SUGGESTED REMEDY
1. Check main and branch
circuit fuses or circuit breakers.
! WARNING: Make sure
main power is turned off.
2. Check line power connections
to fan.
3. Turn ON Fan/Light remote control.
1. Attach blades to fan before
operating.
2. Check to make sure the screws
which attach the blades to the
motor are tight.
! WARNING: Make sure main
power is turned off.
1. Check to be sure screws which
attach the fan blade to the
motor are tight.
2. Check to be sure that the
screws securing the fan
blades seat firmly.
3. Interchanging an adjacent (side
by-side) blade pair can
redistribute the weight and result
in smoother operation.
Or use supplied balancing kit to
balance blades.
UL Model No.: CF144 & CF152
BP7407 44" &
52" Curva Sky
1/11/10
9:54 PM
Page 14
Repair Parts Listing
Damp Part Numbers
Key
Model No.
Model No.
No. Description
CF144BS00
CF152BS00
Wet Part Numbers
Model No.
Model No.
Model No.
Model No.
Model No.
Model No.
CF144CRM00 CF152CRM00 CF144WW00 CF152WW00 CF144ORB00 CF152ORB00
1
Ceiling Mounting Plate
2
Ceiling Trim Ring
3
Ceiling Cover
763988-BS
763988-BS
763988-CRM
763988-CRM
763988-WW 763988-WW 763988-ORB 763988-ORB
4
Lower Housing
763992-BS
763992-BS
763992-CRM
763992-CRM
763992-WW 763992-WW 763992-ORB 763992-ORB
5
Light Kit Plate Assembly
764006
764006
764006
764006
764006
764006
6
Glass Shade
763994-OM
763994-OM
763994-OM
763994-OM
763994-OM
763994-OM
7
No Light Kit Cover
763995-BS
763995-BS
763995-CRM
763995-CRM
763995-WW 763995-WW 763995-ORB 763995-ORB
8
52” Blade Assembly
—
763996-BS
—
763996-BS
—
9
44” Blade Assembly
763998-BS
—
763998-BS
—
10
Harness, Wiring
764007
764007
764007
764007
11
Handheld Transmitter
763979
763979
763979
763979
12
Electronic Receiver with
Wire Connectors
764009
764009
764009
764009
764009
764009
764009
764009
*
Parts Bag, Containing:
764008
764008
764008
764008
764008
764008
764008
764008
13
Connector, Wire, 12 Ga. (3)
—
—
—
—
—
—
—
—
14
Screw, Pan Head, Ceiling
—
—
—
—
—
—
—
—
15
Screw, Flange Head, Blade
—
—
—
—
—
—
—
—
16
Screw, Serrated Head, Lower
Cover, M5 x 10mm (1)
M5 x 16mm (10)
763987
763987
763987
763987
763989-BS
763989-BS
763989-CRM
763989-CRM
763987
763987
763987
763987
763989-WW 763989-WW 763989-ORB 763989-ORB
764006
764006
763994-SST 763994-SST
763996-WW
—
763996-ORB
763998-WW
—
763998-ORB
—
764007
764007
764007
764007
763979
763979
763979
763979
Housing/Light Kit,
M4 x 10mm (1)
17
Kit, Balancing
—
Owner's Manual
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
BP7407
BP7407
BP7407
BP7407
BP7407
BP7407
BP7407
BP7407
14
UL Model No.: CF144 & CF152
BP7407 44" &
52" Curva Sky
1/11/10
9:54 PM
Page 15
Repair Parts
1
14
2
17
3
13
8 - 52"
9 - 44"
15
4
16
10
5
11
5
6
12
Before discarding packaging material, be certain all parts have been removed.
HOW TO ORDER REPAIR PARTS
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION:
• PART NUMBER
• PART DESCRIPTION
• NAME OF ITEM
• MODEL NUMBER
The model number of your Fan will be found on a label attached to the top housing.
For repair parts, phone 1-800-654-3545.
15
UL Model No.: CF144 & CF152
BP7407 44" &
52" Curva Sky
1/11/10
9:54 PM
Page 16
LIMITED WARRANTY
What The Warranty Covers:
This warranty covers the motor and the other components and accessories of your Emerson ceiling fan against all defects in
workmanship and materials. You must be the original purchaser or user of the product to be covered.
What The Period Of Coverage Is:
As it applies to the motor, this warranty will last for the lifetime of your ceiling fan. All other components and accessories are
covered by this warranty for one year from the date you purchased your ceiling fan. ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, MADE WITH RESPECT TO COMPONENTS AND
ACCESSORIES IS ALSO LIMITED TO ONE YEAR.
What Will Emerson Electric Co. Do To Correct Problems:
Emerson Electric Co. will replace a defective Emerson Air Comfort Ceiling Fan motor, blade, component or other accessory at
no charge to you. If repair of the motor or blades is not practical or possible within a reasonable time and no replacement can
be provided, Emerson will refund the actual purchase price of your fan. WE WILL SHIP THE REPAIRED PRODUCT OR
REPLACEMENT TO YOU AT NO CHARGE, BUT YOU ARE RESPONSIBLE FOR ALL COSTS OR REMOVAL, REINSTALLATION
AND SHIPPING OF THE PRODUCT TO EMERSON ELECTRIC CO.
How Can You Get Service:
YOU MUST HAVE PROOF OF YOUR PURCHASE OF THE CEILING FAN TO OBTAIN LIMITED WARRANTY SERVICE. KEEP YOUR
RECEIPT OR OTHER PROOF OF PURCHASE. You can return the product to our factory or to your nearest authorized service
center.
• To return the product to the factory, obtain a return authorization and service identification tag by writing to Air Comfort
Products, Division of Emerson Electric Electric Co., 8100 W. Florissant Ave., St. Louis, MO 63136. Include all model
numbers shown on the product with your request.
• To return the product to an authorized service center, call 1-800-654-3545 for the address of the nearest authorized service
center.
You will be responsible for all insurance, freight or other transportation charges to our factory or authorized service
center. Your Emerson Air Comfort Ceiling Fan should be properly packed to avoid damage in transit since we will not be
responsible for any such damage.
What Is Not Covered:
The glass globes and light bulbs of your ceiling fan are not covered by this warranty. This warranty also does not cover any
defects, malfunctions or failures caused by:
• Repairs by persons not authorized by Emerson Electric Co.,
• Use of parts or accessories not authorized by Emerson Electric Co.,
• Mishandling, improper installation, modifications or damage to your ceiling fan while in your possession, or
• Unreasonable use, misuse, abuse, including failing to do reasonable and necessary maintenance, and normal wear and tear.
Additionally, this warranty and any implied warranty of merchantability or fitness for a particular purpose are voided when:
• The original purchaser or user ceases to own the product, or
• The fan is moved from its original point of installation.
This warranty is only valid within the 50 states of the United States and the District of Columbia. No other written or oral
warranties apply, and no employee, agent, dealer or other person is authorized to give any warranties on behalf of Emerson
Electric Co.
REPAIR, REPLACEMENT OR A REFUND ARE THE EXCLUSIVE REMEDIES AVAILABLE UNDER THIS WARRANTY AND
EMERSON IS NOT RESPONSIBLE FOR DAMAGES OF ANY KIND, INCLUDING INCIDENTAL AND CONSEQUENTIAL DAMAGES.
Incidental damages include but are not limited to such damages as loss of time and loss of use. Consequential damages include
but are not limited to the cost of repairing or replacing other property which was damaged if this product does not work
properly.
How State Law Relates To The Warranty:
Some states do not allow the exclusion or limitation of incidental or consequential damages so the above exclusion or limitation
may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state
to state.
Air Comfort Products
DIVISION OF EMERSON ELECTRIC CO.
8100 W. Florissant • St. Louis, MO 63136
Part No. F40BP74070000
Printed in China 01/10
Form No. BP7407
UL Model No.: CF144 & CF152