Bosch D2071A Installation manual

D2071A
Fire Control/Communicator
Operation and Installation Manual
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Radionics ®
D2071A
12V AC,20V A, 60Hz or +24V DC
12V AC, 20V A, 60Hz or -24V DC
EARTH GND
Replace battery evry 3 to 5 years with
BATTERY model no. D126 (12V, 7Ah) or D1219
BATTERY +
(12V, 2.3Ah). Do not use the D1219 for
NFPA 72 (Ch. 8) applications. Maximum
INITIATING A1charging current 300mA.
INITIATING A2INITIATING B1+
Alarm Initiating Current
Connect to alarm initiating devices, or to
INITIATING B2+
a dry alarm output of an exisitng FACP.
SUPERVISORY HI
See the installation manual.
SUPERVISORY LO
Waterflow retard/reset times: 0-90 sec.
SUPERVISORY HI
Supervisory Circuits
TBL RELAY NC
Connect up to 20 supervisory devices
TBL RELAY COM
per circuit, or to a dry trouble output of
TBL RELAY NO
an exisitng FACP. See installation
manual
for wiring and programming.
ALARM RELAY NC
ALARM RELAY COM
Telephone Trouble Relay
ALARM RELAY NO
Must have D136 relay in socket K5
for optional remote trouble indication.
A member of the Bosch Group
D2071A
This page is intentionally blank
74-06200-000-D
D2071AOperation & Installation Manual
Page 2
Copyright © 2001 Radionics
D2071A
Contents
Contents
1.0
2.0
2.1
2.2
2.3
2.4
2.4.1
2.4.2
2.5
2.6
2.6.1
2.7
2.7.1
2.7.2
2.8
2.9
2.9.1
2.9.2
2.9.3
2.9.4
2.9.5
2.9.6
2.9.7
2.9.8
2.9.9
2.9.10
2.9.11
3.0
3.1
3.2
3.2.1
3.2.2
3.3
3.3.1
3.3.2
3.3.3
3.3.4
3.3.4.1
3.3.4.2
3.4
3.4.1
3.4.1.1
3.4.2
3.4.2.1
FCC Notice ........................................................................................................................................................................... 7
D2071A Overview ............................................................................................................................................................... 9
Introduction ........................................................................................................................................................................... 9
Communicator ....................................................................................................................................................................... 9
RFI/Lightning Protection ....................................................................................................................................................... 9
Materials Included ................................................................................................................................................................ 9
D2071A ................................................................................................................................................................................. 9
D2071AC ............................................................................................................................................................................... 9
Materials Needed ............................................................................................................................................................... 10
Listings and Approvals ....................................................................................................................................................... 10
Mandatory Connections ..................................................................................................................................................... 10
Slave Communicator Applications ..................................................................................................................................... 11
Power for Slave Applications .............................................................................................................................................. 11
Listed Enclosure Required ................................................................................................................................................. 11
Receiving Equipment ......................................................................................................................................................... 12
D2071A Control/Communicator Assembly ....................................................................................................................... 12
Enclosure ............................................................................................................................................................................ 12
Phone Line Trouble Relay (K5) .......................................................................................................................................... 13
Initiating Circuit Alarm Relay (K6) ..................................................................................................................................... 13
Primary Modular Phone Jack ............................................................................................................................................. 13
Alternate Modular Phone Jack ........................................................................................................................................... 13
Phone Line Trouble Buzzer ................................................................................................................................................ 13
Phone Line Trouble (Phone Fail) LED (Yellow) ................................................................................................................. 13
Programmer Connector (J3) .............................................................................................................................................. 13
Terminal Strip ...................................................................................................................................................................... 13
Strain Relief Tab .................................................................................................................................................................. 13
Mounting Tabs ..................................................................................................................................................................... 13
D2071A Installation .......................................................................................................................................................... 15
Before You Begin ................................................................................................................................................................ 16
Earth Ground Wiring ........................................................................................................................................................... 16
12 VAC Mode ...................................................................................................................................................................... 16
24 VDC Mode ...................................................................................................................................................................... 16
Zone 1, Alarm Initiating Circuit .......................................................................................................................................... 16
Description .......................................................................................................................................................................... 16
Class A (NFPA Style D) Circuit Parameters ...................................................................................................................... 16
Retard and Reset Times .................................................................................................................................................... 17
Wiring .................................................................................................................................................................................. 17
Stand-Alone Applications ................................................................................................................................................... 17
Slave Communicator Applications ..................................................................................................................................... 17
Zones 2 and 3, Supervisory Circuits ................................................................................................................................. 18
Description .......................................................................................................................................................................... 18
Mode 1 and Mode 2 Restrictions ....................................................................................................................................... 18
Wiring .................................................................................................................................................................................. 18
Stand-alone Applications ................................................................................................................................................... 18
Copyright © 2001 Radionics
D2071A Operation & Installation Manual
Page 3
74-06200-000-D
D2071A
Contents
3.4.2.2
3.4.3
3.5
3.5.1
3.5.2
3.5.3
3.6
3.6.1
3.6.2
3.6.3
3.7
3.7.1
3.7.2
3.7.2.1
3.8
3.8.1
3.8.2
3.8.3
3.8.4
3.8.5
3.8.5.1
3.9
3.9.1
3.9.2
3.9.3
3.9.4
3.9.5
3.10
3.11
3.11.1
3.11.2
3.11.3
3.12
4.0
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
4.10
5.0
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
5.10
5.11
5.12
5.13
Slave Communicator Applications ..................................................................................................................................... 18
Class B (NFPA Style A) Circuit Parameters ...................................................................................................................... 18
Initiating Circuit Alarm Relay .............................................................................................................................................. 20
Description .......................................................................................................................................................................... 20
Relay Installation ................................................................................................................................................................ 20
Relay Wiring ........................................................................................................................................................................ 20
Phone Line Trouble Relay .................................................................................................................................................. 21
Description .......................................................................................................................................................................... 21
Relay Installation ................................................................................................................................................................ 21
Relay Wiring ........................................................................................................................................................................ 21
Primary Power Supply ........................................................................................................................................................ 21
12 VAC Mode ...................................................................................................................................................................... 21
24 VDC Mode ...................................................................................................................................................................... 22
24 VDC Battery Discharge/Recharge Schedule ............................................................................................................... 22
Secondary Power Supply and Charging Circuit (12 VAC Mode Only) ............................................................................ 22
Battery ................................................................................................................................................................................. 22
Battery Installation .............................................................................................................................................................. 22
Battery Replacement .......................................................................................................................................................... 22
Battery Supervision ............................................................................................................................................................ 22
Battery Charging Circuit ..................................................................................................................................................... 23
12 VAC Battery Discharge/Recharge Schedule ............................................................................................................... 23
Telephone Connections ...................................................................................................................................................... 23
Telephone Cord Installation ............................................................................................................................................... 23
Location ............................................................................................................................................................................... 23
Telephone Line Supervision ............................................................................................................................................... 24
Call Routing ........................................................................................................................................................................ 24
Notification .......................................................................................................................................................................... 25
Cable Tie Installation .......................................................................................................................................................... 25
D2071A Mounting ............................................................................................................................................................... 26
Screw Mounting .................................................................................................................................................................. 26
D2002 Mounting Plate ........................................................................................................................................................ 26
Adhesive Strip Mounting .................................................................................................................................................... 26
End User Instruction Label ................................................................................................................................................ 26
D2071A Programming ...................................................................................................................................................... 27
Description .......................................................................................................................................................................... 27
Navigating Through Handlers and Program Records ...................................................................................................... 27
Function Keys ..................................................................................................................................................................... 27
Data Keys ............................................................................................................................................................................ 27
Helpful Tones ...................................................................................................................................................................... 28
Editing a Record ................................................................................................................................................................. 28
Programmer Connection .................................................................................................................................................... 28
Entering the 2071 Handler ................................................................................................................................................. 28
Program Modules ............................................................................................................................................................... 28
How to Edit the Program Record ....................................................................................................................................... 29
2071 Program Record ...................................................................................................................................................... 31
Account # ............................................................................................................................................................................ 31
Transmit BFSK .................................................................................................................................................................... 31
DTMF Dialing ...................................................................................................................................................................... 31
PriPre ................................................................................................................................................................................... 31
PriPh# .................................................................................................................................................................................. 31
AltPri .................................................................................................................................................................................... 32
AltPh# .................................................................................................................................................................................. 32
12 Volt Mode ....................................................................................................................................................................... 32
Class B Mode ...................................................................................................................................................................... 32
Retard Time ......................................................................................................................................................................... 32
Reset Time .......................................................................................................................................................................... 33
Hrs Til Rpt ........................................................................................................................................................................... 33
Mins Til Rpt ......................................................................................................................................................................... 33
74-06200-000-D
D2071AOperation & Installation Manual
Page 4
Copyright © 2001 Radionics
D2071A
Contents
6.0
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
6.9
6.10
6.11
6.12
6.13
6.14
6.15
6.16
6.17
7.0
7.1
7.2
7.2.1
7.2.2
7.3
7.4
7.5
7.6
7.6.1
7.6.2
8.0
Receiver Reports .............................................................................................................................................................. 35
ALARM ZN 1 ....................................................................................................................................................................... 35
ALARM ZN 2 ....................................................................................................................................................................... 35
ALARM ZN 3 ....................................................................................................................................................................... 35
RESTORAL ZN 1 ................................................................................................................................................................ 35
RESTORAL ZN 2 ................................................................................................................................................................ 35
RESTORAL ZN 3 ................................................................................................................................................................ 35
RESTORAL ZN 9 ................................................................................................................................................................ 35
RESTORAL ZN B ............................................................................................................................................................... 35
RESTORAL ZN C ............................................................................................................................................................... 35
RESTORAL ZN E ............................................................................................................................................................... 35
TROUBLE ZN 1 .................................................................................................................................................................. 35
TROUBLE ZN 2 .................................................................................................................................................................. 35
TROUBLE ZN 3 .................................................................................................................................................................. 36
TROUBLE ZN 9 .................................................................................................................................................................. 36
TROUBLE ZN B .................................................................................................................................................................. 36
TROUBLE ZN C .................................................................................................................................................................. 36
TROUBLE ZN E .................................................................................................................................................................. 36
Troubleshooting Guide .................................................................................................................................................... 37
Introduction ......................................................................................................................................................................... 37
Phone Line Trouble Buzzer, LED, and Relay Activated .................................................................................................... 37
Phone Line Trouble ............................................................................................................................................................. 37
Communications Failure ..................................................................................................................................................... 37
Trouble Zone E .................................................................................................................................................................... 38
Problems Programming with the D5200 Programmer ...................................................................................................... 38
Problems with the Zones (Alarm Initiating and Supervisory Circuits) ............................................................................. 39
Trouble Zone 9 .................................................................................................................................................................... 39
12 VAC Mode (Battery and Transformer) .......................................................................................................................... 39
24 VDC Mode (Connection to FACP) ................................................................................................................................ 39
Specifications .................................................................................................................................................................... 41
Copyright © 2001 Radionics
D2071A Operation & Installation Manual
Page 5
74-06200-000-D
D2071A
Figures and Tables
Figures
Figure 1: D2071A Control/Communicator ........................................................................................................................................ 12
Figure 2: Stand-Alone Installation .................................................................................................................................................... 15
Figure 3: Slave Communicator Installation ...................................................................................................................................... 15
Figure 4: Modes 1, 2 and 3 ............................................................................................................................................................... 19
Figure 5: Relay Sockets .................................................................................................................................................................... 20
Figure 6: RJ31X Wiring ..................................................................................................................................................................... 23
Figure 7: Insert the Cable Tie ........................................................................................................................................................... 25
Figure 8: Secure the Cable Tie and Wires ....................................................................................................................................... 25
Figure 9: Navigating the 2071 Program ........................................................................................................................................... 29
Tables
Table 1: Mandatory Connections for NFPA 72 Central Station and NFPA 72 Remote Station ..................................................... 11
Table 2: 24 VDC Battery Discharge/Recharge Schedule ................................................................................................................ 22
Table 3: 12 VAC Battery Discharge/Recharge Schedule ................................................................................................................ 23
Table 4: Call Routing Assignments ................................................................................................................................................... 24
Table 5: Special Dialing Characters .................................................................................................................................................. 31
74-06200-000-D
D2071AOperation & Installation Manual
Page 6
Copyright © 2001 Radionics
D2071A
FCC Notice
1.0
FCC Notice
This equipment generates, uses and can radiate radio frequency energy. If not installed in accordance with the
manufacturer’s instructions, it may cause interference to radio communications. It has been tested and found to comply
with the specifications in Subpart J of Part 15 of FCC Rules for Class B Computing Devices.
If this equipment causes interference to radio or television reception -- which can be determined by turning the equipment
on and off -- the installer is encouraged to correct the interference by one or more of the following measures: 1)
Reorient the antenna of the radio/television, 2) Connect the AC transformer to a different outlet so the control panel and
radio/television are on different branch circuits, 3) Relocate the control panel with respect to the radio/television.
If necessary, the installer should consult an experienced radio/television technician for additional suggestions, or send
for the “Interference Handbook” prepared by the Federal Communications Commission. This booklet is available from
the U.S. Government Printing Office, Washington D.C. 20402, stock no. 004-000-00450-7.
The D2071A Control/Communicator is registered with the Federal Communications Commission under part 68, for
connection to the public telephone network using an RJ31X or RJ38X jack installed by your local telephone company.
• FCC Registration Number:
AJ9USA-61104-AL-E
• Ringer Equivalence:
0.0B (AC)
1.3B (DC)
Copyright © 2001 Radionics
D2071A Operation & Installation Manual
Page 7
74-06200-000-D
D2071A
FCC Notice
Notes:
74-06200-000-D
D2071AOperation & Installation Manual
Page 8
Copyright © 2001 Radionics
D2071A
D2071A Overview
2.0
D2071A Overview
2.1
Introduction
The D2071A Fire Control/Communicator is a three-zone Digital Alarm Communicator Transmitter (DACT) for use in
limited stand-alone applications or for off-premises monitoring of existing fire alarm control panels (FACPs) in slave
applications.
Zone 1 is a Class A (NFPA Style D) Alarm Initiating Circuit. It can be used to monitor waterflow or other alarm initiating
devices in a stand-alone application, or to monitor an alarm output in a slave application. Zones 2 and 3 are Class B
(NFPA Style A) Supervisory Circuits. They can be used to monitor sprinkler supervision devices such as valve tampers
in a stand-alone application, or to monitor trouble outputs in a slave application.
Primary and alternate phone outputs enable the D2071A to communicate to the Central Station and/or Remote Station.
A built-in phone line supervision circuit with trouble buzzer, LED, and optional Form C relay provides local phone line
trouble annunciation for both phone lines. The D2071A also provides an optional Form C relay output for annunciation
of alarms on the Alarm Initiating Circuit.
The D2071A is housed in a red plastic, non-conductive enclosure. The plastic enclosure insulates the product from
surrounding circuit boards or metal surfaces. This allows you to mount the D2071A in fire alarm control enclosures listed
for use with it. You can also install the D2071A in an economical, fire listed enclosure such as the Radionics D8109 or
D4103R.
2.2
Communicator
The D2071A uses a built-in communicator to transmit reports to a digital receiver. It uses two RJ31X or RJ38X jacks to
connect to two separate phone lines, for a primary and an alternate means of transmitting to the receiver. The D2071A
has full phone line seizure, and complies with FCC regulations for using the public telephone network.
You must program two receiver phone numbers for the D2071A. The communicator first attempts to transmit reports to
the primary phone number. If unable to transmit to the primary number, the communicator switches to the alternate
number. It sends reports to the receiver in BFSK format or Pulsed Fast Single Round format. The communicator only
accepts the 2300 Hz acknowledgment tone. It is compatible with most major digital receivers that accept the BFSK or
Pulsed Fast Single Round formats and generate a 2300 Hz acknowledgment tone.
2.3
RFI/Lightning Protection
The D2071A resists radio frequency interference, and high voltage surges which are common to lightning areas. Spark
gaps and M.O.V.s provide the D2071A with additional electrical protection.
2.4
Materials Included
2.4.1
D2071A
Radionics ships the D2071A Control/Communicator Panel completely assembled. The package includes installation
literature, an end-user information label, two 5 in. double-sided adhesive strips, two mounting screws and washers, a
strain relief cable tie, 32 in. dual connector battery leads, and two 1.8 k Ω EOL resistors for the supervision circuits
(Zones 2 and 3).
2.4.2
D2071AC
You can purchase the D2071A in a D2071AC kit. The kit includes installation literature, an end-user information label,
two mounting screws and washers, a strain relief cable tie, 32 in. dual connector battery leads, two 1.8 k Ω EOL
resistors for the supervision circuits (Zones 2 and 3), a D4103R enclosure, two D161 phone cords, and two conduit
support washers.
The D4103R in the kit comes with a D2002 Mounting Plate and a Basler Electric, model A9115, transformer (Radionics
part number 58-06306-000) installed in the enclosure. This is a UL recognized, Class II transformer rated for 20 VA at
12 VAC. It uses pigtails to hard wire directly to a 110/120 VAC power source.
Copyright © 2001 Radionics
D2071A Operation & Installation Manual
Page 9
74-06200-000-D
D2071A
D2071A Overview
2.5
Materials Needed
The following is a list of additional parts necessary for installing the D2071A :
• D126 Battery: 12 V, 7 Ah battery required for NFPA 72 Remote Station stand-alone applications. The D126 Battery is
also acceptable for NFPA 72.
Note:
The battery must provide 60 hours of standby plus five minutes of alarm operation. Only use a battery in the 12 VAC
mode.
• D1219 Battery: 12 V, 2.3 Ah battery for NFPA 72 Central Station applications only. The battery must provide 24 hours
of standby.
Note:
Only use a battery in the 12 VAC mode.
• D136 Relay (1 or 2) (Optional): One enables Phone Line Trouble Relay (K5). One enables Initiating Circuit Alarm
Relay (K6).
• D161* or D162 Phone Cord (2): Primary and alternate phone line connections.
• D1220 Transformer: Use in the 12 VAC mode only.
• D4103R*/D8109 Enclosure (Optional): Or other UL listed fire enclosure.
• D2002 Mounting Plate* (Optional): To mount the D2071A in a D4103R enclosure.
• D5100 Programmer or D5200 Programmer: With the 2071 Product Handlers loaded.
• D8004 Transformer Enclosure: Required for the D1220 transformer in commercial fire applications if D2071AC kit is
not used.
* Included in the D2071AC kit. D4103R in kit includes hard-wired transformer.
2.6
Listings and Approvals
Underwriters Laboratories lists the D2071A DACT (digital alarm communicator transmitter) under UL Standard 864
(Control Units Fire Signaling Systems) and 1635 (Digital Alarm Communicators) for Central Station Signaling Service
(NFPA 72) and Remote Station Signaling Service (NFPA 72). Install the D2071A in accordance with NFPA 70 (NEC
Article 760).
Additional approvals: FM, CSFM and NYC-MEA.
2.6.1
Mandatory Connections
To comply with Central Station Fire (NFPA 72) or Remote Station (NFPA 72) Signaling Service, connect the D2071A as
described in Table 1. The Class A (NFPA Style D) and Class B (NFPA Style A) circuits shown are mandatory connections
for slave and stand-alone applications. The Installation section of this manual contains detailed wiring instructions.
74-06200-000-D
D2071AOperation & Installation Manual
Page 10
Copyright © 2001 Radionics
D2071A
D2071A Overview
2.7
Slave Communicator Applications
To use the D2071A as a slave communicator to only provide signaling connections, connect the D2071A to an existing
UL listed NFPA 72 FACP. You can use the D2071A in compliance with NFPA standards in the following ways:
2.7.1
1)
To provide NFPA 72 Central Station connections for an existing FACP when only a summary alarm and up to two
trouble signals are required.
2)
To provide NFPA 72 Remote Station signaling connections for an FACP listed for NFPA 72.
3)
To provide Central Station or Remote Station connections to an NFPA 72 Local FACP when required by the Authority
Having Jurisdiction (AHJ).
Power for Slave Applications
For slave communicator applications, connect the D2071A to a 24 VDC Fire Alarm Control Panel (FACP). Do not install
a battery in this configuration. Do NOT connect the D2071A to a 12 VDC power supply or a control panel which only
provides 12 VDC output. If the FACP does not provide a 24 VDC auxiliary power output, a D126 battery, a D1220
transformer, and a D8004 Transformer Enclosure are required. If you use the D2071AC kit, the Basler Electric, model
A9115 (Radionics part number 58-06306-000), transformer installed in the D4103R enclosure replaces the D1220
transformer and the D8004 Transformer Enclosure. It is a UL recognized, Class II transformer rated for 20 VA at 12 VAC.
It uses pigtails to hard wire directly to a 110/120 VAC power source.
2.7.2
Listed Enclosure Required
Unless the monitored FACP is specifically listed or approved for use with the D2071A installed in the same enclosure,
you must install the D2071A in a separate UL listed enclosure. Connect the separate enclosure to the FACP by conduit
no more than 20 feet long. The Radionics D4103R, D8109, and D8108A are all suitable for this purpose. The D2071AC
kit includes a D4103R with a Basler Electric, UL recognized, Class II, hardwire transformer rated for 20 VA at 12 VAC
mounted in the enclosure. It uses pigtails to hard wire directly to a 110/120 VAC power source.
Stand-Alone Applications
Connection
Terminal #
12 VAC Primary Power*
Slave Applications
NFPA 72 Central Station
NFPA 72 Remote Station
NFPA 72 Central Station
NFPA 72 Remote Station
OK
OK
OK
OK
NO
NO
OK
OK
OK
Required
OK
Required
OK
NO
OK
NO
1, 2
24 VDC Primary Power
D126 Battery Backup
(12 VDC, 7 Ah)
4, 5
D1219 Battery Backup
(12 VDC, 2.3 Ah)
Class A, Style D Circuit
6, 7, 8, 9
Retard/Reset Time
(Waterflow Alarm ONLY)
Class B, Style A Circuits
(Recommended Mode)
Earth Ground
Max of 5 waterflow switches or up to 100 mechanically
activated initiating devices (heat detectors or manual
pull stations). NOT suitable for smoke detectors.
Normally open dry alarm output contacts of an existing
FACP.
Consult the appropriate standard or as allowed by the
Authority Having Jurisdiction (AHJ).
N/A
3
3
3
3
10, 11
Can monitor up to 20 valve supervisory switches per
circuit.
Normally open dry trouble contacts of an existing
FACP.
11, 12
Mode 1 is not acceptable. Mode 2 is ONLY acceptable
when a valve tamper device having ONLY a normally
closed contact MUST be used and ONLY upon approval
of the AHJ.
Mode 3 recommended. Modes 1 and 2 are acceptable.
3
Yes
No
* You must use the D8004 Transformer Enclosure or the D2071AC kit for commercial fire applications.
Table 1: Mandatory Connections for NFPA 72 Central Station and NFPA 72 Remote Station
Copyright © 2001 Radionics
D2071A Operation & Installation Manual
Page 11
74-06200-000-D
D2071A
D2071A Overview
2.8
Receiving Equipment
The D2071A must report to compatible, UL listed receiving equipment that meets the following processing capabilities:
• Fire Alarm
• System Trouble
• Low Battery
• 24 Hour Test
• System Restoral
• 2300 Hz Acknowledgment Tone
• Radioncs BFSK or 3x1, 40 pulse-per-second, single round with parity (Radionics superfast)
2.9
D2071A Control/Communicator Assembly
2.9.1
Enclosure
• Dimensions (LxWxD): 6.8 x 4.4 x 1.1 in. (17.3 x 11.2 x 2.8 cm)
• Color: Red
• Construction: UL94V-O flame-rated, ABS plastic, non-conductive
The D2071A enclosure cover slides open approximately 2 inches (5.1 cm) to expose the terminal strip, the programming
jack and the two Form “C” relay sockets. There is no need to completely remove the cover during installation or for
service.
Terminal
Block
Programmer
Connector
(J3)
Phone Line
Trouble
Buzzer
Phone Line
Trouble
LED (Yellow)
Strain
Relief
Tab
LED
Hole
Alternate
Modular
Phone Jack
(J2)
Aromat
DS1E-M
-DC12V
AG20134408
JAPAN
30830 BOTTOMVIEW
Primary
Modular
Phone Jack
(J1)
Aromat
Mounting
Tab
Mounting
Tab
DS1E-M
-DC12V
AG20134408
JAPAN
30830 BOTTOM VIEW
Alarm
Relay
(K6)
Trouble
Relay
(K5)
D2071A
Enclosure
Cover
Figure 1: D2071A Control/Communicator
74-06200-000-D
D2071AOperation & Installation Manual
Page 12
Copyright © 2001 Radionics
D2071A
D2071A Overview
2.9.2
Phone Line Trouble Relay (K5)
Install a D136 Relay in this socket when using the optional Phone Line Trouble Relay (Terminals 13 to 15). The relay
activates when phone line trouble is detected on either the primary or secondary phone line, when communication
failure occurs, and briefly upon power-up.
2.9.3
Initiating Circuit Alarm Relay (K6)
Install a D136 Relay in this socket when using the optional Initiating Circuit Alarm Relay (Terminals 16 to 18). This relay
activates when the initiating circuit is in an alarm condition.
2.9.4
Primary Modular Phone Jack
The primary phone jack connects the D2071A to the primary phone line for transmitting to the receiver.
2.9.5
Alternate Modular Phone Jack
The alternate phone jack connects the D2071A to an alternate phone line for transmitting to the receiver. If the D2071A
fails to contact the receiver after two attempts on the primary line, it switches to the alternate line.
2.9.6
Phone Line Trouble Buzzer
The phone line trouble buzzer sounds when either the primary or the alternate phone line is in a trouble condition, or
when communications failure occurs. Ten failed attempts to transmit any report puts the panel in communications
failure. The phone line trouble LED and relay follow the activity of the buzzer.
The buzzer, LED, and relay are deactivated after a trouble condition on the phone line when the receiver acknowledges
the phone line trouble report, or when the line returns to normal. If the D2071A attempts to transmit the phone line
trouble report ten times without acknowledgment from the receiver, communication failure occurs.
If the D2071A is in communication failure, either the primary or alternate phone line must be detected as normal and a
report acknowledged by the receiver before the buzzer is deactivated.
2.9.7
Phone Line Trouble (Phone Fail) LED (Yellow)
The yellow LED is visible through the top of the D2071A enclosure (upper right corner). The LED lights when the panel
detects phone line trouble on either the primary or secondary phone line, when communication failure occurs, and
briefly upon power-up.
2.9.8
Programmer Connector (J3)
Connect the D5100 or D5200 programmer to the Programmer Connector (J3).
2.9.9
Terminal Strip
The terminal strip connects system wiring for power, ground, a Class A (NFPA Style D) alarm initiating circuit, two Class
B (NFPA Style A) supervisory circuits, and two Form “C” relay outputs.
2.9.10 Strain Relief Tab
The strain relief tab prevents unnecessary strain on connections to the D2071A. Secure all wire running from the
D2071A to the tab using the enclosed cable tie.
2.9.11 Mounting Tabs
The mounting tabs located on each end of the D2071A provide a means of mounting the D2071A with screws. The
adhesive strips provided can also be used to mount the D2071A.
Copyright © 2001 Radionics
D2071A Operation & Installation Manual
Page 13
74-06200-000-D
D2071A
D2071A Overview
Notes:
74-06200-000-D
D2071AOperation & Installation Manual
Page 14
Copyright © 2001 Radionics
D2071A
D2071A Installation
3.0
D2071A Installation
= Power Limited
S
1
12 VAC, 20 VA, 60 Hz
2
12 VAC, 20 VA, 60 Hz
3
EARTH GND
P
4
BATTERY –
P
5
BATTERY +
P
12 VAC, 20 VA
Transformer
= Supervised
S
P
D126, 12V, 7Ah Battery or
D1219, 12V, 2.3Ah Battery +
6
INITIATING A1 –
S
7
INITIATING A2 –
P
8
INITIATING B1 +
9
INITIATING B2 +
P
Max Charging
Current 300 mA
Open= Trouble
Short = Alarm
ALARM
INITIATING
CIRCUIT
Open= Trouble
S
MODE 2
MODE 1
P
P
10
Open = Alarm
S
11
P
Resistance = Alarm
Open = Trouble
S
10
MODE 3
S
11
P
1.8 K Ω
Resistor
NC
1.8 K Ω
Resistor
10
SUPERVISORY HI
11
SUPERVISORY LO
12
SUPERVISORY HI
13
TBL RELAY NC
C
14
TBL RELAY COM
NO
15
TBL RELAY NO
NC
16
ALARM RELAY NC
C
17
ALARM RELAY COM
NO
18
ALARM RELAY NO
SUPERVISORY
CIRCUITS
TELEPHONE
TROUBLE
RELAY
Max Rating
2A at 30 VDC
INITIATING
CIRCUIT
ALARM RELAY
Max Rating
2A at 30 VDC
Figure 2: Stand-Alone Installation
= Power Limited
= Supervised
Primary
Power
Supply
24 VDC Supply +
from UL Listed
Fire Alarm
Control Panel -
S
OR
P
12 VAC, 20 VA
Transformer
S
P
Dry Closure
Alarm
Indicator
Relay
Fire Alarm
Control Panel
(FACP)
Dry Closure
Trouble
Indicator
Relay
N
P S
C
P S
12 VAC, 20 VA, 60 Hz, OR + 24 VDC
2
6
12 VAC, 20 VA, 60 Hz, OR – 24 VDC
Do not connect earth ground
EARTH GND
when connected to a 24 VDC
power supply.
BATTERY –
Do not connect a battery when
connected to a 24 VDC power
BATTERY +
supply. Max Charging Current
300 mA.
INITIATING A1 –
7
INITIATING A2 –
8
INITIATING B1 +
9
INITIATING B2 +
3
Alternate
Power Supply
D126, 12V, 7Ah Battery or
D1219, 12V, 2.3Ah Battery +
1
P
4
P
5
Open = Trouble
Short = Alarm
N
ALARM
INITIATING
CIRCUIT
Open = Trouble
N
P S
C
P S
MODE 3
Short = Alarm
Open = Trouble
SUPERVISORY HI
11
SUPERVISORY LO
12
SUPERVISORY HI
NC
13
TBL RELAY NC
C
14
TBL RELAY COM
NO
15
TBL RELAY NO
NC
16
ALARM RELAY NC
N
1.8 K
Resistor
10
C
17
ALARM RELAY COM
NO
18
ALARM RELAY NO
SUPERVISORY
CIRCUITS
TELEPHONE
TROUBLE
RELAY
Max Rating
2A 30 VDC
INITIATING
CIRCUIT
ALARM RELAY
Max Rating
2A 30 VDC
Figure 3: Slave Communicator Installation
Copyright © 2001 Radionics
D2071A Operation & Installation Manual
Page 15
74-06200-000-D
D2071A
D2071A Installation
3.1
Before You Begin
Follow the instructions in the sub-sections below to install the D2071A. Be aware that some terminals are wired differently
for the stand-alone (Figure 2) and slave (Figure 3) applications.
If you are using the D2071AC kit, mount the D4103R enclosure and have a qualified electrician connect a 110/
120 VAC power source to the black and white leads on the transformer. Be certain the power source is turned
off before you begin the installation of the D2071A.
3.2
Earth Ground Wiring
Note:
Use Terminal 3 for earth ground connections.
3.2.1
12 VAC Mode
To help prevent damage from electrostatic charges or other transient electrical surges, connect the D2071A panel to
earth ground at Terminal 3 before making any other connections to the panel. A grounding rod or cold water pipe are
recommended earth ground references. Do not use telephone or electrical ground for the earth ground connection. Use
#16 AWG (1.5 mm) wire when making the connection. Do not connect any other terminals to earth ground.
3.2.2
24 VDC Mode
When the D2071A is connected to the 24 VDC output of an FACP, do not connect Terminal 3 to earth ground. Doing so
may cause a continuous ground fault condition on the FACP.
3.3
Zone 1, Alarm Initiating Circuit
Note:
Use Terminals 6, 7, 8 and 9 for Zone 1, Alarm Initiating Circuit connections.
3.3.1
Description
Zone 1 is a four-wire, Class A (NFPA Style D) initiating circuit. You can connect up to five waterflow alarm switches or up
to 100 mechanically operated devices such as heat detectors or manual pull stations to this zone. NFPA 72 requires that
you connect a single pull station with waterflow switches. The Authority Having Jurisdiction (AHJ) may specify the
location of this pull station. Other than this exception, do not combine waterflow switches with other types of devices.
Unlike the two wire Class B (NFPA Style A) circuits that are supervised by end-of-line resistors, the double loop Class
A (NFPA Style D) circuit provides alarm response from all initiating devices with a single open or ground fault condition
on the circuit. Connect initiating devices to the D2071A as shown in Figures 2 and 3.
The D2071A has programmable retard (Retard Time) and reset (Reset Time) timers for waterflow alarm installations on
wet pipe sprinkler systems. The timers compensate for water pressure surges and sprinkler alarm valve “fanning”
conditions.
3.3.2
Class A (NFPA Style D) Circuit Parameters
Maximum resistance on the wiring for the sensor loops on the Class A (NFPA Style D) circuit is 100 Ω per loop (between
A1 and A2 100 Ω maximum, between B1 and B2 100 Ω maximum).
To determine the electrical condition of the circuit, use a multimeter to measure the voltage across the terminal connections.
The D2071A must be powered up and the loops in a normal condition. Connect one lead of the multimeter to a negative
(-) terminal (6 or 7) and the other lead to a positive (+) terminal (8 or 9). The input voltages should be as follows:
Electrical Condition Multimeter Reading (measured zone input voltage)
• Normal:
Terminals ‡ˆ = 1.0 to 1.9 VDC
• Alarm (shorted):
Terminals ‡ˆ = 0.0 to 0.3 VDC
74-06200-000-D
D2071AOperation & Installation Manual
Page 16
Copyright © 2001 Radionics
D2071A
D2071A Installation
3.3.3
Retard and Reset Times
Only use the Zone 1 retard/reset feature for waterflow switches and/or controls without a retard/reset feature of their
own.
The retard timer prevents false alarms from conditions such as water supply surges in wet pipe sprinkler systems.
Surges may result in the brief activation of a waterflow alarm switch. The value you enter in the program item Retard
Time determines the length of time that the waterflow switch must remain activated before an alarm report is initiated.
Generally, a 15 second retard is adequate, but a longer interval may be necessary when extended surge conditions
exist.
Reset Time is an additional program parameter that compensates for sprinkler alarm valve “fanning” conditions in wet
pipe systems with unique hydraulic problems. Fanning occurs when a sprinkler head operates, or the inspector’s test
valve is opened, and the waterflow switch does not remain activated long enough to overcome the retard time, but
cycles between alarm and normal conditions.
The retard timer (Retard Time) and the reset timer (Reset Time) work together as follows:
• The retard timer (Retard Time) keeps track of the amount of time which the Alarm Initiating Circuit is in the alarm
condition. It begins counting when the circuit enters the alarm condition.
• The reset timer (Reset Time) determines when the retard timer is reset to zero. When the Alarm Initiating Circuit
enters a non-alarm (restored or trouble) condition, after being in the alarm condition, the retard timer stops at its
current value and the reset timer starts counting.
• If another alarm condition is detected before the reset timer reaches the value you entered in Reset Time, the retard
timer resumes counting from where it left off, and the reset timer is set to zero.
• If the amount of time specified in the Retard Time program item accumulates in one or more successive alarm
activations, the D2071A transmits an Alarm Zone 1 report and activates the alarm relay.
• The retard timer resets to zero only when the circuit remains in a non-alarm condition (restored or trouble) for the
amount of time entered in Reset Time.
• When the Alarm Initiating Circuit has been normal for the time in Reset Time, the D2071A sends a Restoral Zone 1
report.
Reset Time is typically set at half the Retard Time. If Retard Time were set at 15 seconds, Reset Time would be set at
7 or 8 seconds.
3.3.4
Wiring
3.3.4.1 Stand-Alone Applications
Connect the normally-open contacts of each waterflow switch (maximum of 5) or mechanically activated initiating
device to the Alarm Initiating Circuit in parallel as shown in Figure 2.
3.3.4.2 Slave Communicator Applications
1)
Connect the Alarm Initiating Circuit to an alarm indicator output (normally-open, dry closure) on the FACP (see
Figure 3).
2)
Connect Terminals 6 and 7 to the common contact, and Terminals 8 and 9 to the normally-open contact.
3)
Program Retard Time and Reset Time for 0 seconds when connecting the Alarm Initiating Circuit to an existing
FACP.
Copyright © 2001 Radionics
D2071A Operation & Installation Manual
Page 17
74-06200-000-D
D2071A
D2071A Installation
3.4
Zones 2 and 3, Supervisory Circuits
Note:
Use Terminals 10, 11 and 12 for supervisory circuit connections.
3.4.1
Description
Zones 2 and 3 are Class B (NFPA Style A) circuits that can monitor sprinkler supervision devices such as valve tampers
(maximum of 20 per circuit) in stand-alone applications. In slave communicator applications these circuits monitor the
trouble outputs of an associated FACP.
You can wire the Class B (NFPA Style A) circuits in three different ways: Mode 1, 2, or 3. Program item Class B Mode
determines the mode for both Zones 2 and 3. Wire both circuits for the same mode configuration. Connect dry contact
devices to the Supervisory Circuits in series (normally-closed), or in parallel (normally-open). Install a 1.8 k Ω resistor
at the end of the Class B (NFPA Style A) circuits if needed (see Figure 4).
Mode 1 has only two status conditions: Alarm and Normal. Modes 2 and 3 have three status conditions: Alarm, Trouble,
and Normal. The D2071A transmits an alarm report for a trouble condition when you use a Mode 1 or Mode 2 circuit to
monitor an FACP trouble output or sprinkler valve tamper.
3.4.1.1 Mode 1 and Mode 2 Restrictions
You cannot use Mode 1 for sprinkler supervision (stand-alone) in NFPA 72 Remote Station installations. Mode 3 is
recommended. Only use Mode 2 when a normally closed contact valve tamper device must be used, and only upon
approval of the authority having jurisdiction. For more information concerning Modes and NFPA requirements, refer to
the Listings and Approvals section in the front of this manual.
3.4.2
Wiring
3.4.2.1 Stand-alone Applications
• Connect supervision devices (maximum of 20 per circuit) such as valve tamper switches to Terminals 10 and 11
(Zone 2) or 11 and 12 (Zone 3) as shown in Figure 4.
• Program item Class B Mode for the wiring configuration you use.
• There should be no more than 100 Ω resistance on the sensor loops for the Class B (NFPA Style A) circuits.
3.4.2.2 Slave Communicator Applications
• When connecting the D2071A to an FACP, use the Mode 3 configuration for slave communicator applications (see
Figure 4).
• Connect Terminals 10 and 11 (Zone 2) or 11 and 12 (Zone 3) to the trouble outputs (dry closure) on the FACP.
• Connect Terminal 10 or 12 to the normally-open contact, and Terminal 11 to the common contact.
• Install a 1.8 k Ω resistor between the normally open and normally closed contacts.
• You must program Class B Mode for Mode 3.
3.4.3
Class B (NFPA Style A) Circuit Parameters
To determine the electrical condition of the Class B (NFPA Style A) Supervisory Circuits, use a voltmeter to measure the
voltage across the terminal connections (refer to Figure 4 for loop voltages). The loop must be connected, and the
D2071A must be powered.
74-06200-000-D
D2071AOperation & Installation Manual
Page 18
Copyright © 2001 Radionics
D2071A
D2071A Installation
MODE 1
10
11
NO
10
C
11
The loops are configured for NC devices only. No EOL
resistor is used. The loops are not supervised for troubles.
Mode 1 is not acceptable for stand-alone applications.
• Normal:
• Alarm (Open):
0.0 - 1.5 VDC
1.8 - 13.0 VDC
NC
MODE 2
A 1.8 k Ω EOL resistor is used across each NC
device in the series loops. Mode 2 is acceptable for
NFPA 72 Central Station and Remote Station Standalone applications only when a NC valve tamper
device must be used and only upon approval of the
authority having jurisdiction.
10
11
1.8 k Ω Resistor
NO
10
C
11
• Normal:
• Alarm (Resistance):
• Trouble (Break):
A single off-normal device puts the loops into alarm.
A broken circuit or multiple off-normal devices put the
loops into trouble (unless the loop was previously in
alarm).
NC
1.8 k Ω Resistor
1.8 k Ω Resistor
10
11
1.8 k Ω Resistor
NO
10
C
11
NC
0.0 - 1.5 VDC
1.8 - 9.0 VDC
9.3 - 13 VDC
MODE 3
A 1.8 k Ω EOL resistor is used at the end of the loops.
Trouble reports are sent on an open circuit. Mode 3
is required for sprinkler supervision in NFPA 72
Central Station and Remote Station slave applications
or for trouble reports from the FACP. It is the
recommended mode for 72 Central Station slave
applications.
•
•
Normal:
Alarm (Closed):
1.9 - 5.8 VDC
0.0 - 1.7 VDC
•
Trouble (Open):
6.0 - 10.2 VDC
Figure 4: Modes 1, 2 and 3
Copyright © 2001 Radionics
D2071A Operation & Installation Manual
Page 19
74-06200-000-D
D2071A
D2071A Installation
3.5
Initiating Circuit Alarm Relay
Note:
Use Terminals 16, 17 and 18 for initiating circuit alarm relay connections.
3.5.1
Description
Install a D136 Relay in Socket K6 to use the optional Initiating Circuit Alarm relay. The D136 provides a Form “C” dry
contact, rated at 2 A maximum current at 30 VDC (power from independent supply). The relay activates (reverse state)
when the Class A (NFPA Style D) Alarm Initiating Circuit (Zone 1) goes into an alarm condition. It deactivates when the
circuit restores to normal.
• Terminal 17 is the relay common
• Terminal 16 is normally-closed
• Terminal 18 is normally-open
In a normal state, Terminals 16 and 17 have continuity. When activated, Terminals 17 and 18 have continuity.
3.5.2
Relay Installation
Install a D136 Relay into Socket K6 (labeled ALARM RELAY) as follows:
3.5.3
1)
Slide back the D2071A cover to expose the socket as shown in Figure 5.
2)
The D136 relay has two pins on one side and three pins on the other side. Place the relay into socket with the pins
oriented as shown in Figure 5. You can install the relay flush left or right.
Relay Wiring
Connect only low voltage power sources and devices to Terminals 16, 17, and 18. Do not use the D2071A’s standby
battery to provide a power output for the circuit.
10
11
12
13
14
15
16
TROUBLE RELAY
K5
K6
17
18
ALARM RELAY
Figure 5: Relay Sockets
74-06200-000-D
D2071AOperation & Installation Manual
Page 20
Copyright © 2001 Radionics
D2071A
D2071A Installation
3.6
Phone Line Trouble Relay
Note:
Use Terminals 13, 14 and 15 for phone line trouble relay connections.
3.6.1
Description
Install a D136 Relay in Socket K5 to use the optional Phone Line Trouble relay. The D136 provides a Form “C” dry
contact, rated at 2 A maximum current at 30 VDC (power from independent supply). The relay activates (reverse state)
when a faulted condition appears on either the primary or alternate phone lines or when a communication failure
occurs.
The Phone Line Trouble Relay activates whenever the Phone Line Trouble Buzzer sounds. Refer to Phone Line Trouble
Buzzer in the D2071A Control/Communicator Assembly section for more information on relay activation and restoral.
3.6.2
Relay Installation
Install a D136 Relay into Socket K5 (labeled TROUBLE RELAY) as follows:
3.6.3
1)
Slide back the D2071A cover to expose the socket as shown in Figure 5.
2)
The D136 relay has two pins on one side and three pins on the other side. Place the relay into socket with the pins
oriented as shown in Figure 5. You can install the relay flush left or right.
Relay Wiring
• Terminal 14 is the relay common
• Terminal 13 is normally-closed
• Terminal 15 is normally-open
In a normal state, Terminals 13 and 14 have continuity. When activated, Terminals 14 and 15 have continuity.
Only connect low voltage power sources and devices to Terminals 13, 14, and 15. Do not use the D2071A’s standby
battery to supply power for the circuit. In some slave communicator applications the Phone Line Trouble Relay (Terminals
13-15) on the D2071A can be connected to a trouble zone input on the FACP.
3.7
Primary Power Supply
Note:
Use Terminals 1 and 2 for primary power supply connections.
You can power the D2071A Control/Communicator using a 12 VAC, 20 VA transformer and standby battery, or you can
connect it to the 24 VDC output of an FACP. Either method can be used for NFPA 72 applications. DO NOT connect the
D2071A to a 12 VDC power supply of an existing FACP. In such cases, use the transformer and battery for 12 VAC
mode.
• Parallel Activation on Power-up: The Phone Line Trouble Buzzer, Relay and LED activate briefly upon AC or battery
power-up, indicating the DACT is operational.
3.7.1 12 VAC Mode
Connect a 12 VAC, 20 VA transformer to Terminals 1 and 2 using #18 AWG (1.2 mm) stranded wire (maximum length
50 ft., 15.3 m). Commercial fire applications require the D8004 transformer enclosure for the D1220 transformer or the
D2071AmC kit.
The hardwire transformer mounted in D4103R enclosure included in D2071AC kit replaces the D1220
transformer. Be certain the 110/120 VAC power source is turned off when you connect the black and white
transformer leads to the source. Connect the yellow leads from the transformer to Terminals 1 and 2.
Program the 12 Volt Mode program item YES. See Section 3.8.1 of this manual for battery installation instructions.
NFPA 72 applications require the 110/120 VAC, 60 Hz commercial power for the transformer be un-switched and from
a reliable source. NFPA 72 applications require a dedicated branch circuit to supply the 110/120 VAC power for the
transformer. The means of being disconnected for the circuit must only be available to authorized personnel, and
identified as a “Fire Alarm Control Circuit.”
Never share the transformer with other equipment. Foreign grounds on the AC input damage the D2071A’s
power circuit.
Copyright © 2001 Radionics
D2071A Operation & Installation Manual
Page 21
74-06200-000-D
D2071A
D2071A Installation
3.7.2
24 VDC Mode
Connect a 24 VDC, uninterrupted, regulated, auxiliary output from an FACP to Terminals 1 and 2. Set program item 12
Volt Mode to NO. Terminals 1 (+) and 2 (-) are polarity protected when the D2071A is programmed for the 24 VDC mode.
Do not connect a 12 VDC standby battery and do not connect earth ground to the D2071A when it is in 24 VDC mode.
The discharge/recharge schedule below shows the voltages at Terminals 1 and 2 that generate battery reports with the
D2071A in 24 VDC mode. If the voltage falls below 11.1 VDC, the D2071A is not operational.
3.7.2.1 24 VDC Battery Discharge/Recharge Schedule
• Source supervised is the 24 VDC input from the FACP.
• Schedule applies to Terminals 1 and 2 on the D2071A.
Discharge Cycle
Recharge Cycle
27.6 volts - FACP battery float voltage
AC On - FACP battery recharging begins
21.8 volts - Battery trouble report
24.7 volts - Battery restoral report (RESTORAL ZN 9)
11.1 volts - (TROUBLE ZN 9) Disable
27.6 volts - FACP battery charged
Table 2: 24 VDC Battery Discharge/Recharge Schedule*
* Actual voltage may vary ± 5%
3.8
Secondary Power Supply and Charging Circuit (12 VAC Mode Only)
Note:
Use Terminals 4 and 5 for secondary power supply and charging circuit connections.
3.8.1
Battery
The D2071A charging circuit is only calibrated for lead-acid type batteries. Do not connect the D2071A to a battery
when it is using 24 VDC from an existing FACP. The battery supplies power for the system during interruptions in primary
(AC) power in the 12 VAC mode.
For NFPA 72 applications, you must use a 12 VDC, 7 Ah, sealed, lead-acid, rechargeable battery (Radionics model
D126).
For NFPA 72 applications, use a 12 VDC, 2.3 Ah, sealed, lead-acid, rechargeable battery (Radionics model D1219).
The Radionics model D126 exceeds the standby requirements and is also acceptable.
3.8.2
Battery Installation
1)
Install the battery in an upright position at the base of the metal enclosure.
2)
Connect the negative side of the battery (black) to D2071A Terminal 4 with the black lead provided with the D2071A.
3)
Connect the positive side of the battery (red) to D2071A Terminal 5 with the red lead.
• Parallel Activation on Power-up: The Phone Line Trouble Buzzer, Relay and LED activate briefly upon AC or battery
power-up, indicating the DACT is operational.
3.8.3
Battery Replacement
Radionics recommends battery replacement every 3 to 5 years under normal use. Do not install the transformer into a
power source that is routinely switched off. This does not comply with NFPA standards and causes heavy discharges of
the battery which may result in premature failure.
3.8.4
Battery Supervision
During an AC power loss, the battery supplies all power to the D2071A. In doing so, the battery slowly discharges. When
the battery voltage drops below 11.8 VDC, the D2071A sends a TROUBLE ZN 9 report to the receiver.
After the AC is restored, the battery begins to charge. At 13.4 volts the D2071A sends a battery restoral report, RESTORAL
ZN 9.
• Restoral ZN 9 Exceptions: If a battery is not connected to the D2071A when AC power is connected, the panel still
sends a RESTORAL ZN 9 report to the receiver. A RESTORAL ZN 9 is also sent after the programmer is disconnected
from the D2071A.
74-06200-000-D
D2071AOperation & Installation Manual
Page 22
Copyright © 2001 Radionics
D2071A
D2071A Installation
3.8.5
Battery Charging Circuit
The D2071A charges the battery with a float charge circuit. Maximum charging current is 300 mA. The Battery Discharge/
Recharge Schedule shows voltages during the discharge/recharge cycle.
3.8.5.1 12 VAC Battery Discharge/Recharge Schedule
• Source supervised is the battery connected to the D2071A.
Discharge Cycle
Recharge Cycle
13.8 volts - FACP battery float voltage
AC On - Battery recharging begins
11.8 volts - Battery trouble report (TROUBLE ZN 9)
9.0 volts - Battery trouble report (only if battery
discharged below 8.5 volts)
8.5 volts - Disable all processing and memory
functions (deep battery discharge can occur below
this level)
13.4 volts - Battery restoral report (RESTORAL ZN 9)
13.8 volts - Battery charged
Table 3: 12 VAC Battery Discharge/Recharge Schedule*
* Actual voltage may vary by as much as ± 5%.
3.9
Telephone Connections
3.9.1
Telephone Cord Installation
Connect the primary phone line to the D2071A modular Jack “J1” using a D161 or D162 Phone Cord. Connect the
alternate phone line to the D2071A modular Jack “J2” using another D161 or D162 Phone Cord.
You must connect separate primary and alternate phone lines to the D2071A for all applications.
3.9.2
Location
To prevent jamming of alarm and other reports, wire and locate the RJ31X or RJ38X jack so that normal phone use is
temporarily interrupted while the communicator transmits data (see Figure 6). After installation, confirm that the D2071A
seizes the line, acquires dial tone, and reports correctly to the receiver.
Full Modular Phone Jack
Premises
Phone
R1
T1
1
2
3
4
5
6
7
8
R
T
Incoming
Telco Line
RJ31X Module
Figure 6: RJ31X Wiring
Copyright © 2001 Radionics
D2071A Operation & Installation Manual
Page 23
74-06200-000-D
D2071A
D2071A Installation
3.9.3
Telephone Line Supervision
The D2071A monitors both the Primary and Alternate telephone lines while the communicator is idle by “sniffing” the
line for trouble. Phone line trouble is defined as line voltage below 10 VDC and current less than 10 mA. Total time for
trouble indication is 210-240 seconds. If there is a report to transmit, the D2071A does not “sniff” the phone lines until
the report is transmitted or a communication failure occurs. The D2071A reports a faulted condition on the Primary
phone line as a TROUBLE ZN B and the Alternate phone line as a TROUBLE ZONE C.
Each line is “sniffed” once a minute if both lines are good. If a line is determined to be in trouble, the D2071A steps up
the test rate and “sniffs” once every ten seconds. If the trouble still exists after 15 samples (150 seconds), the panel
sends a trouble report and activates the buzzer, Phone Fail LED, and Phone Line Trouble Relay (if installed). See
Section 3.6 of this manual for telephone trouble relay for installation instructions.
The buzzer, LED, and relay are deactivated after a trouble condition on the phone line when the receiver acknowledges
the phone line trouble report, or when the line returns to normal. If the D2071A attempts to transmit the phone line
trouble report ten times without acknowledgment from the receiver, communication failure occurs.
If the D2071A is in communication failure, either the primary and alternate phone lines must be detected as normal and
a report acknowledged by the receiver before the buzzer, LED, and relay are deactivated. Refer to the troubleshooting
section of this manual for help in finding the cause of phone line problems.
The buzzer, light, and relay may remain activated for up to 24 hours if the communications failure was not due to trouble
conditions detected on the phone lines, and no other report is transmitted before the next scheduled test report.
3.9.4
Call Routing
After one failed attempt to transmit a report, the D2071A attempts to transmit a TROUBLE ZN E report, in addition to the
original report. After two failed attempts to reach the receiver, the D2071A switches from the primary to the alternate
phone line. The D2071A switches and makes a dialing attempt even if you have not programmed an alternate phone
number.
The D2071A continues alternating between the primary and alternate lines for a total of ten attempts. If the D2071A
cannot make contact with the receiver after 10 attempts, the it goes into communications failure, and activates the
Phone Fail LED, Phone Line Trouble Buzzer, and Phone Line Trouble Relay (if installed).
Total time from the first attempt to communications failure is up to ten minutes. A RESTORAL ZN E is the only report
transmitted after a communications failure. Any report in the D2071A's buffer prior to communications failure is not
transmitted. The buffer is cleared.
For all applications you must program both a primary and an alternate phone number. The numbers must be different.
Attempt
Routing
1
Phone Number 1 Primary Line
2
Phone Number 1 Primary Line
3
Phone Number 2 Alternate Line
4
Phone Number 1 Alternate Line
5
Phone Number 2 Primary Line
6
Phone Number 1 Primary Line
7
Phone Number 2 Alternate Line
8
Phone Number 1 Alternate Line
9
Phone Number 2 Primary Line
10
Phone Number 1 Primary Line
Table 4: Call Routing Assignments
74-06200-000-D
D2071AOperation & Installation Manual
Page 24
Copyright © 2001 Radionics
D2071A
D2071A Installation
3.9.5
Notification
Do NOT connect registered equipment to party lines or coin operated telephones. If the local telephone company
requests notification before you connect the D2071A to the telephone network, supply the following information:
• the particular line you are connecting the panel to,
• the make, model, and serial number of the device, and
• the FCC registration number (AJ9USA-61104-AL-E) and ringer equivalence (0.0B = AC, 1.3B = DC).
If the telephone company makes changes in its communications facilities, equipment, operations, or procedures that
may affect the performance of the communicator, the phone company is obligated to notify the user in writing.
3.10
Cable Tie Installation
After making all of the necessary connections, secure all wire coming out of the D2071A to the Strain Relief Tab. Follow
the procedure below.
1)
String the cable tie through the middle of the “H” shaped Strain Relief Tab.
2)
Bunch the wires attached to the D2071A together (see Figure 7). Make sure none of them become disconnected.
4)
Wrap the cable tie around the wires and firmly secure the tie to the Strain Relief Tab (see Figure 8).
Strain
Relief
Tab
Cable
Tie
Figure 7: Insert the Cable Tie
Cable
Tie
Strain
Relief
Tab
Figure 8: Secure the Cable Tie and Wires
Copyright © 2001 Radionics
D2071A Operation & Installation Manual
Page 25
74-06200-000-D
D2071A
D2071A Installation
3.11
D2071A Mounting
Mount the D2071A inside a UL listed fire enclosure of appropriate size or, as the D2071A enclosure is non-conductive,
in the same enclosure with an existing FACP. Unless the monitored FACP is specifically listed or approved for use with
the D2071A installed in the same enclosure, you must install the D2071A in a separate UL listed enclosure.
When installing the D2071A in the same enclosure with an existing FACP, leave room on the bottom of the enclosure for
the battery. Do not mount the D2071A in a location where it restricts the flow of cooling air to the FACP power supply or
similar device.
When mounting the D2071A in a separate UL listed enclosure such as the D4103R or D8109. Connect the enclosure to
the FACP by conduit (not to exceed 20 feet). The D2071A can be mounted in the enclosure using any of the methods
below.
3.11.1 Screw Mounting
1)
Determine the mounting location in the enclosure.
2)
Position the D2071A in the desired location.
3)
Using a pencil, mark the location of the mounting tab holes.
4)
Drill appropriate size holes (1/8 in. for the screws provided).
5)
Mount the D2071A using two screws. Two #8 screws and washers are provided.
3.11.2 D2002 Mounting Plate
The D2002 Mounting Plate is used to mount the D2071A in a D4103R enclosure. It is installed in the enclosure provided
with the D2071AC kit. Follow the procedure below to install the D2071A with the D2002 mounting plate.
1)
Secure the mounting plate to the four standoffs in the D4103R enclosure with the four #6 screws provided with the
mounting plate.
2)
Mount the D2071A to the mounting plate using the two #8 screws provided with the D2071A.
3.11.3 Adhesive Strip Mounting
The two adhesive strips provided can be used to mount the D2071A in the enclosure with the FACP or in a separate
enclosure. Choose a location with a smooth, clean, and dry mounting surface.
3.12
1)
Turn the D2071A over to show the back of the enclosure.
2)
Remove the protective backing from one side of a 5 in. adhesive strip.
3)
Press the strip firmly to the back of the D2071A near the top edge.
4)
Remove the protective backing from one side of the other 5 in. adhesive strip.
5)
Press the strip firmly to the back of the D2071A near the bottom edge.
6)
Bend back or remove any tabs in the enclosure that may prevent the D2071A from being securely mounted.
7)
Remove the remaining protective backing from the adhesive strips.
8)
Attach the D2071A to the enclosure by pressing it firmly into the desired location.
End User Instruction Label
An end user label is included for use when the D2071A is connected to an FACP. As the D2071A does not have any end
user serviceable parts, the label instructs the user to call for service if they cannot silence the D2071A from the FACP.
Affix this label in a location easily seen by the end user. The front of the FACP enclosure is an ideal location.
74-06200-000-D
D2071AOperation & Installation Manual
Page 26
Copyright © 2001 Radionics
D2071A
D2071A Programming
4.0
D2071A Programming
4.1
Description
This section provides a brief operation overview of the D5200 Programmer. It is not intended to be a substitute for the
D5200 Operation Manual (74-06176-000). You should be familiar with the D5200 Operation Manual before attempting to
program any Radionics Product.
To program the D2071A DACT with the D5200 Programmer, make sure the programmer contains the 2071 Product
Handler Program. See the D5200 Programmer Operation Manual for D5200 update instructions.
4.2
Navigating Through Handlers and Program Records
Access program items by navigating through “groups” of the programmer. Use the red ENTER GROUP and EXIT
GROUP keys to move in and out of each group (see Figure 9).
Use the red up ↑ and down ↓ arrow keys to scroll through the list of items at each group. Scroll through a list of available
product handlers at the Product Handler Group. See saved record titles at the Record Group, and program items are at
the Program Item group.
Use the red left ← and right → arrow keys to move the cursor horizontally within one line of the LCD display.
Figure 9 shows an example of how to use navigational keys to move through the 2071 program. Use these keys the
same way for all product handlers.
4.3
Function Keys
Six function keys simplify the use of the programmer.
• ON: The red ON key switches the programmer on. This key does not power down the programmer. Switch the D5200
off by selecting 5200 OFF in the PRODUCT HANDLERS menu, or it will power down automatically after the programmed
Time Out time has elapsed.
• HELP: The red HELP key switches the programmer into help mode. See the D5200 Operation and Installation Manual
for more information.
• CANCEL: Use the red CANCEL key to undo changed items if you have not yet accepted the change by pressing the
white ENTER key.
• CLEAR: The red CLEAR key erases unENTERed or ENTERED program item data, and replaces it with blank spaces.
• RECV (COPY): The red RECV (COPY) key moves a copy of the record in the attached product to the D5200
Programmer.
• SEND (LOAD): The red SEND (LOAD) key moves a copy of the record in the D5200 Programmer to a product you are
programming.
4.4
Data Keys
The white keys on the keyboard are used for data entry.
Copyright © 2001 Radionics
D2071A Operation & Installation Manual
Page 27
74-06200-000-D
D2071A
D2071A Programming
4.5
Helpful Tones
The D5200 Programmer emits four distinct sounds, which notify the user of key presses, data acceptance/rejection, and
system errors.
• Click: A short, sharp click occurs every time you press a key. The programmer does not click when you press the ON,
CAP LOCK, and SHIFT keys.
• Pip: A short, single frequency tone sounds when you press the white ENTER key and the D5200 accepts the
change.
• Tweedle: A quick series of pips indicating that you pressed an invalid key or made an inappropriate entry.
• Buzz: A sour, flat tone indicates a system error. Examples of typical system errors follow:
• A product is not connected to D5200 when you try to copy or load it.
• The D5200 is notifying you of a low battery condition.
• The D5200 announces that it will automatically count down and then turn off.
• You are attempting to delete a record or handler.
• You are entering into a product handler which contains a TIMEOUTSAVE record. The TIMEOUTSAVE record
was saved by the D5200 when the it automatically turned off to save power.
4.6
Editing a Record
To make changes to an existing 2071 record:
4.7
1)
Scroll to the 2071 product handler from the Product Handlers menu using the red ↓ or ↑ keys, and press the red
ENTER GROUP key.
2)
Scroll to the appropriate record title using the red ↓ or ↑ keys, and press the red ENTER GROUP key.
3)
Scroll to the appropriate program item using the red ↓ or ↑ keys, and edit the entry. Press the white ENTER key to
enter the new data.
4)
Press the red EXIT GROUP key to exit from the record. The SAVE display appears if changes have been made to
any program item entries in the record.
Programmer Connection
To access the four-pin Programmer Connector (J3), slide back the cover on the D2071A. The Programmer Connector is
next to Terminal 1 (see Figure 1). The D2071A is ready for programming after connecting it to the programmer. It is not
necessary to reset the D2071A before loading to, or copying from the panel.
• Programming before installing the phone lines may sound the buzzer: You can program the D2071A prior to
installation. However, if the D2071A is powered and not connected to a phone line, the phone fail buzzer sounds after
approximately ten minutes. Power down the unit to silence the buzzer.
Program the Radionics D2071A using the Radionics D5200 Programmer containing the 2071 Product Handler. Before
programming the D2071A, it is recommended that you read and become familiar with this section of the manual.
4.8
4.9
Entering the 2071 Handler
1)
Starting at PRODUCT HANDLERS, press the red ↓ key until the cursor is on 2071. Press the red ENTER GROUP
key.
2)
The cursor appears on the NEWRECORD prompt. Press the red ENTER GROUP key.
3)
The D5200 displays Account #.
Program Modules
Unlike larger Radionics products, the 2071 Product Handler does not group Program Items in Program Modules. You
are in the Program Item Level as soon as you enter the 2071 program.
74-06200-000-D
D2071AOperation & Installation Manual
Page 28
Copyright © 2001 Radionics
D2071A
D2071A Programming
PASSWORD
DISPLAY
D5200 PROGRAMMER
Radionics Inc.
Rev [##.##]
Password:
PRODUCT HANDLER
LEVEL
RECORD
LEVEL
4112
7112
PROGRAM ITEM
LEVEL
6112
636
ENTER
GROUP
2071 [##.##]
2071
ENTER
GROUP
8112
NEWRECORD
Account #
DISKSTAT
RECORD1
Transmit BFSK No
SECURITY
RECORD2
DTMF Dialing
RECORD3
PriPre
UPDATE
EXIT
GROUP
EXIT
GROUP
Yes
ENTER
PriPh#
DELETE
DELETE
5200 OFF
COPY
AltPre
VISMODE
AltPh#
LOCKRECORD
12 Volt Mode
Yes
Class B Mode
3
Retard Time
Reset Time
0
0
Hrs Til Rpt
0
Mins Til Rpt
0
Figure 9: Navigating the 2071 Program
4.10
How to Edit the Program Record
Each D2071A DACT programming option (Program Item) is listed with a Display and a Default (as they appear in the
programmer display), a set of Selections, and a Description.
The Selections are the only entries available for a particular Program Item. For instance, the Program item Account #
can only use 0 through 9, B through F, or no entry. Do not use unlisted entries.
To edit program items, change the entry and press the white ENTER key. If the entry is valid, the programmer moves
the cursor to the next prompt. When you have edited all the Program Items in the record, the programmer returns you to
the first program item in the record.
Exiting the 2071 program: You can exit from any point within the program. To exit the 2071 program, press the EXIT
GROUP key until the D5200 Programmer displays PRODUCT HANDLERS.
Copyright © 2001 Radionics
D2071A Operation & Installation Manual
Page 29
74-06200-000-D
D2071A
D2071A Programming
Notes:
74-06200-000-D
D2071AOperation & Installation Manual
Page 30
Copyright © 2001 Radionics
D2071A
2071 Program Record
5.0
2071 Program Record
This record selects several functions of the D2071A DACT, including the account number used to identify the location
during communication, how it will dial the phone number, how the D2071A will be powered, and loop response times.
5.1
Account #
• Default:
Blank
• Selections:
0 to 999, BBB to FFF, or Blank
All entries should be right-justified. Blank Entry = No account number (sends 000 in pulse, sends nothing in BFSK).
5.2
Transmit BFSK
• Default:
Yes
• Selections:
Yes or No
Program the receiver reporting format.
• Yes: Transmit in BFSK format with 2300 Hz acknowledgment.
• No: Transmit in fast, single round, expanded pulsed format with a checksum digit and 2300 Hz acknowledgment.
5.3
DTMF Dialing
• Default:
Yes
• Selections:
Yes or No
• Yes: Dual Tone Multi-Frequency Dialing of the telephone numbers.
• No: Pulse dialing of the telephone numbers.
5.4
PriPre
• Default:
Blank
• Selections:
0 to 9, B to F, or Blank
Prefix for the Primary receiver telephone number. Enter up to nine characters.
• Blank: No prefix/area code. A delay of up to 7 seconds is automatically inserted in front of the prefix.
Note:
See Table 5 Special Dialing Characters for other selections.
5.5
PriPh#
• Default:
Blank
• Selections:
0 to 9, B to F, or Blank
Primary receiver telePhone number. Enter up to seven characters.
Note:
See Table 5 Special Dialing Characters for other selections.
Primary and alternate phone numbers MUST be programmed, and the primary number MUST be different from the
alternate phone number.
Selection
Effect on Dialing
Comments
B
(*) Character
Used in accessing special telephone features.
C
3-second pause
Inserts a pause between digits while dialing.
D
7-second dial tone wait
Waits up to 7 seconds for a dial tone before dialing.
E
(#) Character
Used in accessing special telephone features.
F
Changes from rotary to
DTMF or vice versa
Use when accessing some long distance carriers
while using rotary-dial phone lines.
Table 5: Special Dialing Characters
Copyright © 2001 Radionics
D2071A Operation & Installation Manual
Page 31
74-06200-000-D
D2071A
2071 Program Record
5.6
AltPri
• Default:
Blank
• Selections:
0 to 9, B to F, or Blank
Prefix for the Alternate receiver telephone number. Enter up to nine characters.
• Blank: No prefix/area code. A delay of up to seven seconds is automatically inserted in front of the prefix.
Note:
See Table 5 Special Dialing Characters for other selections.
5.7
AltPh#
• Default:
Blank
• Selections:
0 to 9, B to F, or Blank
Alternate receiver telePhone number. Enter up to seven characters.
Note:
See Table 5 Special Dialing Characters for other selections.
Primary and alternate phone numbers must be programmed, and the alternate number must be different from the
primary phone number.
5.8
12 Volt Mode
• Default:
Yes
• Selections:
Yes or No
Enable 12 or 24 Volt operation Mode.
• Yes: 12 VAC, 20 VA, 60 Hz transformer operation
• No: 24 VDC supply from an existing FACP
5.9
Class B Mode
• Default:
3
• Selections:
1-3
Program the mode of operation for the Class B (NFPA Style A) Supervisory Circuits (Zones 2 and 3).
• 1: Mode 1 - not acceptable for stand-alone applications
• 2: Mode 2 - restricted use for stand-alone applications
• 3: Mode 3 - required for most stand-alone applications
Note:
For detailed mode specifications, refer to Section 3.4 of this manual for Supervisory Circuit installation instructions.
5.10
Retard Time
• Default:
0
• Selections:
0-90
Program the Retard Timer for the Class A (NFPA Style D), Alarm Initiating Circuit (Zone 1). Enter the number of seconds
for the retard time. After the alarm condition is detected on the sensor loops, the retard timer is started. An alarm report
is not transmitted until the retard timer reaches the value entered in Retard Time. If the faulted condition restores before
the retard timer reaches the value entered in Retard Time, the alarm report is not transmitted. For a more detailed
explanation of the retard timer, see the Zone 1, Alarm Initiating Circuit installation instructions.
Consult the appropriate NFPA Standard or the local AHJ for acceptable retard times.
74-06200-000-D
D2071AOperation & Installation Manual
Page 32
Copyright © 2001 Radionics
D2071A
2071 Program Record
5.11
Reset Time
• Default:
0
• Selections:
0-90
Program the Reset Timer for the Class A (NFPA Style D), Alarm Initiating Circuit (Zone 1). Enter the number of seconds
for the reset time. The circuit must be in a non-alarm (restored or trouble) condition for the number of seconds entered
here before the retard timer is set to zero.
Note:
For a more detailed explanation of the reset timer, see Section 3.3 for Zone 1, Alarm Initiating Circuit installation
instructions.
5.12
Hrs Til Rpt
• Default:
0
• Selections:
0-25
Number of Hours unTil the first test Report is sent. Program the number of hours from when the panel is powered up,
or reset with the programmer, to when the first test report is sent. If this entry and Min Til Rpt are both left defaulted at
0, the first test report is sent in 12 hours and all subsequent reports are sent at 24 hour intervals thereafter.
5.13
Mins Til Rpt
• Default:
0
• Selections:
0-59
Number of Minutes unTil the first test Report is sent. Program the number of additional minutes the first test report is
delayed over and above the hours programmed in Hrs Til Rpt.
• Test Timer Default Delay: When the unit is powered up the first test occurs 12 hours later unless you program
a delay in Hrs Til Rpt and/or Mins Til Rpt.
Copyright © 2001 Radionics
D2071A Operation & Installation Manual
Page 33
74-06200-000-D
D2071A
2071 Program Record
Notes:
74-06200-000-D
D2071AOperation & Installation Manual
Page 34
Copyright © 2001 Radionics
D2071A
Receiver Reports
6.0
Receiver Reports
6.1
ALARM ZN 1
A closure or short between the two loops of the Class A (NFPA Style D) Alarm Initiating circuit. This report is
delayed by the time specified in Retard Time (for waterflow alarm applications only).
6.2
ALARM ZN 2
• Mode 1: Open on the Class B (NFPA Style A) Supervisory circuit, Terminals 10 and 11.
• Mode 2: Resistance on the Class B (NFPA Style A) Supervisory circuit, Terminals 10 and 11.
• Mode 3: Closure or short between terminals or a ground fault on the positive (+) side of the Class B (NFPA Style
A) Supervisory circuit, Terminals 10 and 11.
6.3
ALARM ZN 3
• Mode 1: Open on the Class B (NFPA Style A) Supervisory circuit, Terminals 10 and 11.
• Mode 2: Resistance on the Class B (NFPA Style A) Supervisory circuit, Terminals 10 and 11.
• Mode 3: Closure or short between terminals or a ground fault on the positive (+) side of the Class B (NFPA Style
A) Supervisory circuit, Terminals 10 and 11.
6.4
RESTORAL ZN 1
The Class A (NFPA Style D) Alarm Initiating circuit returned to normal from an alarm or trouble condition. This
report is delayed by the time specified in Reset Time when the circuit restores from an alarm condition.
6.5
RESTORAL ZN 2
• All modes: Trouble or Alarm condition on Zone 2 has cleared.
6.6
RESTORAL ZN 3
• All modes: Trouble or Alarm condition on Zone 3 has cleared.
6.7
RESTORAL ZN 9
• 12 VAC Mode: This report is transmitted after AC power is restored, the panel has been programmed, or the
battery is changed or recharged.
• 24 VDC Mode: This report is transmitted when DC power input is applied, when the DC power input reaches
27.6 VDC after falling below 24. 3 VDC, or after programming the panel.
6.8
RESTORAL ZN B
Primary phone line restored.
6.9
RESTORAL ZN C
Alternate phone line restored.
6.10
RESTORAL ZN E
Normal test timer activation.
6.11
TROUBLE ZN 1
A break or ground on either loop of the Class A (NFPA Style D) Alarm Initiating circuit (no retard time applies).
6.12
TROUBLE ZN 2
• Mode 1: Not available.
• Mode 2: Class B (NFPA Style A) circuit, Terminals 10 and 11, open.
• Mode 3: Class B (NFPA Style A) circuit, Terminals 10 and 11, open.
Copyright © 2001 Radionics
D2071A Operation & Installation Manual
Page 35
74-06200-000-D
D2071A
Receiver Reports
6.13
TROUBLE ZN 3
• Mode 1: Not available.
• Mode 2: Class B (NFPA Style A) circuit, Terminals 11 and 12, open.
• Mode 3: Class B (NFPA Style A) circuit, Terminals 11 and 12, open.
6.14
TROUBLE ZN 9
• 12 VAC Mode: Low Battery.
• 24 VDC Mode: DC power input less than 24.3 volts.
6.15
TROUBLE ZN B
Open or short on primary phone line.
6.16
TROUBLE ZN C
Open or short on alternate phone line.
6.17
TROUBLE ZN E
• Communications failure after ten attempts to transmit a report. Reports in the D2071A's buffer when communications
failure occurs are not transmitted. The buffer is cleared.
or
• Test timer failed to report on the first attempt.
or
• When received in the same transmission (phone call) with another report, a TROUBLE ZN E indicates the other
report(s) in the transmission did not get through on the first attempt.
74-06200-000-D
D2071AOperation & Installation Manual
Page 36
Copyright © 2001 Radionics
D2071A
Troubleshooting Guide
7.0
Troubleshooting Guide
7.1
Introduction
Radionics provides this guide to help you troubleshoot problems with the D2071A. To prevent problems from occurring,
read the preceding sections of this manual and verify that the panel is correctly installed and programmed.
7.2
Phone Line Trouble Buzzer, LED, and Relay Activated
There are two basic conditions, phone line trouble and failure to communicate (communications failure), that activate
the phone line trouble buzzer, LED, and relay.
7.2.1
Phone Line Trouble
If the phone line trouble buzzer, LED, and relay activate or if a TROUBLE ZN B or TROUBLE ZN C is received, follow the
procedure outlined below.
1)
Verify that the cords for both lines are correctly connected to the RJ31X or RJ38X jacks and the D2071A.
2)
Verify that the RJ31X or RJ38X jacks are wired correctly. The incoming phone line must be wired to Terminals 4 and
5. The in-house phone system must be wired to Terminals 1 and 8.
3)
Verify that all telephones are on hook and not on hold. Some telephone company systems automatically drop the
voltage and current when phones are left off hook for extended periods. Usually placing the phone on hook restores
the phone line.
If after completing the steps above, the phone line is not restored, meter the phone lines first for voltage and then
current. You should meter at least 20 VDC when the D2071A is idle ("on hook"). If the voltage is below 20 VDC, meter
for current. There should be at least 10 mA of current on the line. If your readings are below the minimum values, contact
your telephone company repair service.
7.2.2
Communications Failure
Communications failure occurs after ten unsuccessful attempts to reach the receiver. Follow the procedure described in
Section 7.2.1 to verify that there is no problem with the phone lines at the D2071A installation. If the phone lines are
good, monitor the lines (preferably at the receiver) for one of the symptoms listed below.
• Symptom: The line rings but the receiver does not pick up.
1) Verify that the lines are correctly connected to the receiver.
2) Verify that correct prefixes and phone numbers for the receiver have been programmed into the D2071A.
• Symptom: The D2071A reaches a busy signal for all ten attempts to reach the receiver.
1) Verify that correct prefixes and phone numbers for the receiver have been programmed into the D2071A.
2) The receiver's call load may be too great. Additional phone lines may be needed for the receiver.
3) Verify that the phone lines are not shorted between the phone company's equipment and the receiver by placing
a call to the number for the receiver. If you hear the line ring, but the ring detector does not light, or if you hear a
busy signal and the green on line (OL) indicator is not lit, call the phone company for service.
• Symptom: The receiver answers the call and provides an acknowledgment tone, but the communicator does not
transmit its reports.
1) Verify that the receiver is producing a 2300 Hz acknowledgment tone.
• Symptom: The receiver answers the call and provides an initial “handshake” acknowledgment tone, but does not
acknowledge the D2071A's report transmission with a “kiss-off” acknowledgment tone.
1) Verify that the receiver is compatible with the format the D2071A is using (either BFSK or Radionics Superfast).
See Section 5.2 “Transmit BFSK” of this manual.
2) Noisy phone lines may be interfering with report transmission. Try making a voice call on the line to verify the
noisy condition. It may be necessary to have the phone company check the lines.
Copyright © 2001 Radionics
D2071A Operation & Installation Manual
Page 37
74-06200-000-D
D2071A
Troubleshooting Guide
7.3
Trouble Zone E
See Section 6.17 “TROUBLE ZN E” of this manual for the causes of this report. If TROUBLE ZN E reports regularly
accompany other reports check the following:
1)
After two attempts to reach the receiver, a D2071A switches to the alternate phone line for the third attempt. Verify
that the primary phone is a DTMF line.
2)
If the D2071A is programmed for DTMF dialing and you have verified that it is connected to DTMF phone lines, try
programming it for pulse dialing. The local phone company may not be compatible with the dialing speed of the
D2071A.
3)
The D2071A may be getting a busy signal at the first dialing attempt. The receiver's call load may be too great.
Additional phone lines may be needed for the receiver.
4)
Noisy phone lines may be interfering with report transmission. Try making a voice call on the line to verify the noisy
condition. It may be necessary to have the phone company check the lines.
5)
Verify that Zone 1 Style D initiating circuit is normal. See Section 3.3 “Zone 1, Alarm Initiating Circuit” of this
manual.
6)
Verify that Zones 2 and 3 Style A supervisory circuits are normal. See Section 3.4 “Zones 2 and 3, Supervisory
Circuits” of this manual.
7)
If using the 24 Volt Mode, test Terminals 1 and 2 for proper input voltage. See Section 3.7.2 “Primary Power Supply,
24 Volt Mode” of this manual.
8)
If using 12 Volt Mode, test Terminals 1 and 2 for proper input voltage. See Section 3.7.1 “Power Supply, 12 VAC
Mode” of this manual.
9)
If using the 12 Volt Mode, test the battery for proper float voltage. See Section 3.8 “Secondary Power Supply and
Charging Circuit (12 Volt Mode Only), Battery Lead Supervision (12 Volt Mode Only)” of this manual.
10) Make sure the battery leads are connected and not corroded. See Section 3.8 “Secondary Power Supply and
Charging Circuit (12 Volt Mode Only), Battery Lead Supervision (12 Volt Mode Only)” of this manual.
7.4
Problems Programming with the D5200 Programmer
Before attempting to program the D2071A, be certain the 2071 Product Handler is loaded in the programmer. You
should also be familiar with the basic operation of the programmer. See the D5200 Operation Manual (74-06255-000).
If you still experience problems, check for the symptoms below.
• Symptom: After pressing SEND LOAD, the programmer displays Plug in 2071.
1) Verify the D5206 adapter is securely plugged into the D2071A.
2) Verify the D5203 programmer cord is securely plugged into the D5206 adaptor.
3) Verify the D5203 programmer cord is plugged into the COMMUNICATOR port on the
programmer.
4) Verify the D2071A is connected to the appropriate power supply.
74-06200-000-D
D2071AOperation & Installation Manual
Page 38
Copyright © 2001 Radionics
D2071A
Troubleshooting Guide
7.5
Problems with the Zones (Alarm Initiating and Supervisory Circuits)
• Symptom: Zone 1 (Alarm Initiating Circuit) does not go into alarm.
You must maintain a short between loop A (Terminals 6 and 7) and loop B (Terminals 8 and 9) for at least the time
programmed in Retard Time.
• Symptom: Zone 1 (Alarm Initiating Circuit) does not restore immediately after an alarm.
The circuit must remain normal for at least the time programmed in Reset Time.
• Symptom: Zone 1 (Alarm Initiating Circuit) remains in trouble or alarm with all devices connected to the circuit
normal.
An open or ground on the circuit causes a trouble report. Remove the circuit loops from the D2071A and meter
them for continuity. There should be no more than 100 Ω resistance between the wires that connect to terminals
6 and 7 and between the wires that connect to Terminals 8 and 9.
With the wires for the circuit loops still removed from the D2071A, meter them for continuity to ground.
• Symptom: Zone 2 or 3 (Supervisory Circuits) remains in trouble or alarm with all devices connected to the circuit
normal.
1) Verify that the circuit is wired for the mode you chose in the Class B Mode program item.
2) Copy the program from the D2071A to verify the Class B Mode program item is programmed correctly.
3) An open on the circuits causes a trouble report for modes 2 and 3, and an alarm report for mode 1. A ground can
cause an alarm report for modes 2 and 3.
Remove the circuit loops from the D2071A and meter them for continuity. There should be no more than 100 Ω
plus the value of the resistors in the circuit between the wires that connect to Terminals 10 and 11 or between the
wires that connect to Terminals 11 and 12.
With the wires for the circuit loops still removed from the D2071A, meter them for continuity to ground.
7.6
Trouble Zone 9
A TROUBLE ZN 9 report tells you there is a problem with the battery when the D2071A is in 12 VAC mode or a problem
with the power supply in the 24 VDC mode. Check for the following:
7.6.1
7.6.2
12 VAC Mode (Battery and Transformer)
1)
Verify that there is at least 12 VAC on terminals 1 and 2.
2)
The outlet the transformer is plugged into should meter between 110 and 120 VAC.
3)
Verify that the output for the transformer connected to terminals 1 and 2 is rated for 12 VAC and at least 20 VA.
4)
Disconnect the transformer from terminals 1 and 2 and meter the battery at terminals 3 and 4. A fully charged
battery should show 13.8 volts.
5)
Make sure the battery is a 12 V sealed lead acid type. It should be rated at 2.3 or 7 Ah or greater, depending on the
NFPA classification of the installation.
24 VDC Mode (Connection to FACP)
1)
Verify that there is 27.6 VDC on Terminals 1 and 2.
2)
Verify that earth ground is not connected to Terminal 3.
3)
Verify that there is not a battery connected to Terminals 4 and 5.
4)
Verify that program item 12 Volt Mode is set to NO.
Copyright © 2001 Radionics
D2071A Operation & Installation Manual
Page 39
74-06200-000-D
D2071A
Troubleshooting Guide
Notes:
74-06200-000-D
D2071AOperation & Installation Manual
Page 40
Copyright © 2001 Radionics
D2071A
Specifications
8.0
Specifications
• Power Input:
• 12 VAC, 20 VA with 12 VDC battery
• 24 VDC
• Operating Current:
Specification
12 VAC Mode
Average/Communicating
24 VDC Mode
Idle Current
29.5 mA
30.0 mA
Battery Charging
51.0 mA
N/A
Alarm with Relay
50.0/110 mA
61.0/115 mA
Alarm without Relay
31.5/79.0 mA
32.0/80.0 mA
Phone Trouble with Relay
82.0/120.0 mA
84.5/140 mA
Phone Trouble without Relay
54.0/110 mA
55.5/110 mA
Alarm and Trouble with Relay
110/160 mA
140/170 mA
Alarm and Trouble without Relay
55.5/102 mA
58.0/140 mA
• Minimum Panel Operation Voltage:
• 8.5 VDC in 12 V Mode
• 11.1 VDC in 24 V Mode
• Zone 1 Voltage:
Multimeter in parallel with normal loop Terminals 6 and 7 (-) and normal loop Terminals 8 and 9 (+).
• Normal:
1.92 VDC
• Alarm:
0.3 VDC
• Open:
N/A
• Response Time:
0.2 to 90 seconds, depending on Retard/Reset Time.
• Zones 2 and 3 Voltage:
Multimeter in parallel with normal loop Terminals 10 and 11 (ZN 2), 11 and 12 (ZN 3).
Mode 1
• Normal:
0.0 VDC
• Alarm (Open):
1.8 VDC
• Response Time:
approximately 2 to 4 seconds
Mode 2
• Normal:
0.0 VDC
• Alarm (Resist.):
1.8 VDC
• Trouble (Break):
9.3 VDC
• Response Time:
approximately 2 to 4 seconds
Mode 3
• Normal:
5.8 VDC
• Alarm (Closed):
1.7 VDC
• Trouble (Open):
10.3 VDC
• Response Time:
approximately 2 to 4 seconds
Copyright © 2001 Radionics
D2071A Operation & Installation Manual
Page 41
74-06200-000-D
D2071A
Specifications
• Phone Voltage:
• Minimum: 20 VDC
• Normal:
48 to 52 VDC; 24 to 26 VDC
• Operating Temperature:
• +32 to +120° F (0 to +49°C)
• Enclosure:
• Color:
Red
• Size (LxW):
7.8 x 4.4 in. (20.0 x 11.2 cm) including mounting tabs
• Material:
Non-conductive plastic ABS UL94V-O
• Wire Specifications:
• Refer to NEC, NFPA 70, Article 760 for wire specifications.
D1220 Transformer Wiring Distances
74-06200-000-D
#18 AWG (1.2 mm)
250 ft. (76.2 m) maximum
#16 AWG (1.5 mm)
374 ft. (114 m) maximum
#14 AWG (1.8 mm)
600 ft. (182.9 m) maximum
#12 AWG (2.3 mm)
1,000 ft. (304.8 m) maximum
D2071AOperation & Installation Manual
Page 42
Copyright © 2001 Radionics
D2071A
Index
Index
Symbols
F
12 VAC Battery Discharge/Recharge Schedule 23
2071 Program Record 31
24 VDC Battery Discharge/Recharge Schedule 22
FCC Notice 7
FCC Registration Number 7
Function Keys 27
A
H
Alternate Modular Phone Jack 13
Helpful Tones 28
How to Edit the Program Record 29
B
Battery 22
12 VAC Battery Discharge/Recharge Schedule 23
24 VDC Battery Discharge/Recharge Schedule 22
Charging Circuit 23
Installation 22
Replacement 22
Supervision 22
C
Cable Tie Installation 25
Call Routing 24
Class A (NFPA Style D) Circuit Parameters 16
Class B (NFPA Style A) Circuit Parameters 18
Communications Failure 37
I
Initiating Circuit Alarm Relay 20
Installation 20
Wiring 20
Initiating Circuit Alarm Relay (K6) 13
L
Listed Enclosure Required 11
Listings and Approvals 10
M
Mandatory Connections 10
Modes 1, 2 and 3 19
Mounting Tabs 13
D
D2071A Assembly
Enclosure Dimensions 12
D2071A Installation 15
D2071A Materials Included 9
D2071A Materials Needed 10
D2071A Mounting 26
Adhesive Strip Mounting 26
D2002 Mounting Plate 26
Screw Mounting 26
D2071A Overview
Communicator 9
Introduction 9
RFI/Lightning Protection 9
D2071A Programming 27
D2071AC Materials Included 9
Data Keys 27
E
Earth Ground Wiring 16
Editing a Record 28
End User Instruction Label 26
Entering the 2071 Handler 28
Copyright © 2001 Radionics
N
Navigating Through Handlers and Program Records 27
NFPA 72 Mandatory Connections 11
P
Parallel Activation on Power-up 21, 22
Phone Line Trouble 37
Phone Line Trouble Buzzer 13
Phone Line Trouble Buzzer, LED, and Relay Activate 37
Phone Line Trouble LED 13
Phone Line Trouble Relay 21
Installation 21
Wiring 21
Phone Line Trouble Relay (K5) 13
Power for Slave Applications 11
Primary Modular Phone Jack 13
Primary Power Supply 21
12 VAC Mode 21
24 VDC Mode 22
Problems Programming with the D5200 Programmer 38
Problems with the Zones 39
Program Modules 28
Programmer Connection 28
Programmer Connector (J3) 13
D2071A Operation & Installation Manual
Page 43
74-06200-000-D
R
Receiver Reports 35
Receiving Equipment 12
Restoral ZN 9 Exceptions 22
Retard and Reset Times 17
Ringer Equivalence 7
RJ31X Wiring 23
S
Secondary Power Supply and Charging Circuit (12 VA 22
Slave Communicator Applications 11
Slave Communicator Installation 15
Specifications 41
Stand-Alone Installation 15
Strain Relief Tab 13
T
Telephone Connections 23
Location 23
RJ31X Wiring 23
Telephone Cord Installation 23
Telephone Line Supervision 24
Telephone Line Supervision 24
Terminal Strip 13
Trouble Zone 9 39
Trouble Zone E 38
Troubleshooting Guide 37
Z
Zone 1, Alarm Initiating Circuit 16
Slave Communicator Applications 17
Stand-Alone Applications 17
Wiring 17
Zones 2 and 3, Supervisory Circuits 18
Mode 1 and Mode 2 Restrictions 18
Slave Communicator Applications 18
Stand-alone Applications 18
Wiring 18
© 2001 Radionics, a division of Detection Systems, Inc.
PO Box 80012, Salinas, CA 93912-0012 USA
Customer Service: (800) 538-5807
74-06200-000-D
Operation & Installation Manual
04/01
D2071A
Page 44 of 44