Shark NP320C Owner's Guide
Add to My manuals16 Pages
Shark NP320: The Shark NP320 is a powerful and versatile vacuum cleaner that can be used for a variety of cleaning tasks. It features a lightweight and portable design, making it easy to use and store. The NP320 comes with a variety of attachments, including a crevice tool, dusting brush, and upholstery brush, so you can clean all types of surfaces. The vacuum also has a powerful suction that can easily remove dirt, dust, and debris.
advertisement
NP320 series
OWNER’S GUIDE
NP320series_40_IB_ENG_120320_1.indd 1
www.sharkclean.com
12-03-20 2:48 PM
IMPORTANT SAFETY INSTRUCTIONS
For Household Use Only
WHEN USING AN ELECTRICAL
APPLIANCE, BASIC SAFETY PRECAUTIONS
SHOULD ALWAYS BE OBSERVED,
INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS BEFORE USING
YOUR SHARK
®
LIFT-AROUND
™
PORTABLE
VAC.
POLARIZED PLUG:
To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician.
DO NOT force into outlet or try to modify to fit.
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR INJURY:
GENERAL ELECTRICAL SAFETY:
1. Unplug from electrical outlet when not in use and before servicing.
2. DO NOT use the vacuum with a damaged cord or plug. This appliance has no serviceable parts. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to EURO-PRO
Operating LLC for examination, repair, or adjustment.
DO NOT unplug by pulling on the cord; to unplug, grasp the plug, not the cord.
wet hands.
WARNING:
To reduce the risk of electric shock or injury, do not use outdoors or on wet surfaces.
9. corners. The use of an extension cord is not recommended.
10. DO NOT leave the appliance plugged in when not in use.
11. Keep the cord away from heated surfaces.
12. Turn off all controls before plugging or unplugging the vacuum cleaner.
13. Always turn off this appliance before attaching or removing accessories.
2
TOLL FREE: 1-800-798-7398
NP320series_40_IB_ENG_120320_1.indd 2 12-03-20 2:48 PM
GENERAL USE:
1. Use only as described in this manual.
2.
NOT use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce air flow.
3. Keep your work area well lit.
4. surfaces such as chairs or tables.
the vacuum or use as a toy. Close attention is necessary when used by or near children.
6. dropped, damaged, left outdoors, or submerged in water. Return to EURO-PRO Operating LLC for examination, repair, or adjustment.
7. in place.
GENERAL CLEANING:
1. DO NOT pick up large-sized objects.
2. glass, nails, screws or coins that could damage the vacuum cleaner.
3. such as hot coals, cigarette butts, matches or hot ash.
DO NOT pick up flammable or combustible materials such as lighter fluid, gasoline, or kerosene or use vacuum in areas where they may be present.
DO NOT pick up toxic solutions such as chlorine bleach, ammonia, or drain cleaner.
vapors are present from paint, paint thinner, moth-proofing substances, flammable dust or other explosive or toxic materials.
7. DO NOT vacuum up any liquids.
HOSE ATTACHMENTS:
or other liquids.
9. only on dry surfaces.
10. Use extra care when cleaning on stairs.
paths, the hose, or the accessories become blocked, turn the vacuum cleaner off. Remove all obstructions before you turn on the unit again.
2. Keep the end of the hose and accessory openings away from face and body.
3. Keep cleaning tools and hose suction openings away from hair, face, fingers, uncovered feet, or loose clothing.
4. Only use manufacturer’s recommended attachments.
DUST CUP/FILTERS/ACCESSORIES:
Before turning on the vacuum:
1. Make sure that all filters are thoroughly dry after routine cleaning.
2. Make sure that the dust cup and all filters are in place after routine maintenance.
3. Make sure accessories are free of blockages.
4. Only use filters and accessories provided by
EURO-PRO Operating LLC. [Failure to do so will void the warranty.]
SAVE THESE
INSTRUCTIONS
www.sharkclean.com
3
NP320series_40_IB_ENG_120320_1.indd 3 12-03-20 2:48 PM
This manual covers model numbers:
NP320 40
NP320C 40
TECHNICAL SPECIFICATIONS
Voltage: 120V., 60Hz
Watts: 550 W
Amps: 4.6 A
4
TOLL FREE: 1-800-798-7398
NP320series_40_IB_ENG_120320_1.indd 4 12-03-20 2:48 PM
Contents
Thank you for purchasing the
Shark
®
Lift-Around
™
Portable Vac.
Getting Started ............................................................................6
How to Use ...................................................................................8
Maintenance ................................................................................9
Checking for Blockages ...............................................................11
Storing ..........................................................................................12
Resetting the Motor Thermostat ...............................................12
Ordering Replacement Parts ......................................................12
Troubleshooting Guide ................................................................13
Warranty & Registration .............................................................15
NP320series_40_IB_ENG_120320_1.indd 5 www.sharkclean.com
5
12-03-20 2:48 PM
Getting Started
A
D
E
F
B
C
G
H
J
K
I
FIRST THING’S FIRST, YOU NEED TO KNOW
WHAT’S IN THE BOX YOU JUST OPENED:
A
Lift-Around
™
Portable Vac
B
Removable Tool Caddy
C
Power Brush
D Upholstery Brush
E Crevice Tool
F Dusting Brush
G
Straight Suction Nozzle
Use the Shark
®
Lift-Around
™
Portable
Vac as a stand alone vacuum for spotcleaning small areas and large piles of debris, or with the Flexible Hose and cleaning tools for above-floor cleaning.
H
Flexible Hose
I Floor Kit Handle
J Telescopic Tube
K Shoulder Strap
6
TOLL FREE: 1-800-798-7398
NP320series_40_IB_ENG_120320_1.indd 6 12-03-20 2:48 PM
NOTE: Always turn the power off before attaching or detaching accessories.
REMOVABLE TOOL CADDY (B)
Specially designed to hold the crevice tool, dusting brush and upholstery brush for quick access to tools when vacuuming and cleaning around the house.
POWER BRUSH (C)
This small accessory has an air driven brushroll for cleaning upholstery, pet hair and even auto interiors.
UPHOLSTERY BRUSH (D)
This unique tool was engineered for fast and easy removal of pet hair from upholstery.
CREVICE TOOL (E)
Reach deep into narrow spaces and clean between cushions, under radiators and baseboards and in hard to reach crevices and corners.
DUSTING BRUSH (F)
Dust shelves, lamp shades, window blinds, books, furniture and other household items.
STRAIGHT SUCTION NOZZLE (G)
Powerful cleaning on low-pile carpets and hardwood floors.
FLEXIBLE HOSE (H)
With the right cleaning tool in place and the Flexible
Hose, you can extend your reach into hard-to-clean areas.
NOTE: Use the Flexible Hose without any accessories attached for large debris cleaning.
FLOOR KIT HANDLE (I)
Designed for easy manoeuvrability and effortless swivel.
TELESCOPIC TUBE (J)
Extend and adjust your reach farther into hard-toclean areas.
SHOULDER STRAP (K)
Specialized design to make carrying the Portable
Vac with ease. The removable Shoulder Strap is ergonomic and easily distributes weight across the shoulder.
www.sharkclean.com
7
NP320series_40_IB_ENG_120320_1.indd 7 12-03-20 2:48 PM
How to Use
Align arrows to attach tool caddy
Pull out to remove tool caddy
Fig. 1
Fig. 4
Fig. 2
Power
Button
Fig. 5
Fig. 3
ASSEMBLING THE LIFT-AROUND
™
PORTABLE VAC
1
Insert the end of the flexible hose into the connector on the back of the Lift-Around™
Portable Vac. (fig. 1)
2
Insert the removable tool caddy onto the front of the Portable Vac. (fig. 2) To remove the tool caddy, hold the vacuum by the handle, pull out slightly from the right side and then remove it from the Portable Vac. (fig. 3)
3
Insert the crevice tool, dusting brush, upholstery brush or power brush into the openings on the tool caddy. (fig. 3)
4
Attach the shoulder strap onto the hooks on the handle of the Portable Vac. (fig. 4)
5
Empty Dust Cup after cleaning and periodically during cleaning when it appears full. (See
“Maintenance” section for instructions.)
8
TOLL FREE: 1-800-798-7398
Fig. 6
FOR ADDED COMFORT OR FOR AN EXTENDED
REACH
6
Attach the floor kit handle to the flexible hose.
Push it in until it is secure. (fig. 6)
7
Insert the telescopic tube into the end of the floor kit handle. Push it in until it is secure. (fig. 6)
NOTE: All accessories may be used with the flexible hose, the floor kit handle or the telescopic tube.
8
Attach the desired accessory to the end of the flexible hose, floor kit handle or telescopic tube by pushing it in until it is tightly secured. (fig. 6)
9
While holding the Portable Vac by the handle, press down on the power button to turn the
Portable Vac on and begin vacuuming. Press down again to turn the vacuum off. (fig. 5)
NP320series_40_IB_ENG_120320_1.indd 8 12-03-20 2:48 PM
Maintenance
To reduce the risk of electric shock, unplug the unit before performing any cleaning, maintenance, or troubleshooting checks.
Reassemble all parts securely before operating vacuum.
For best results empty the Dust Cup after each use; empty several times during prolonged usage or when it reaches the MAX fill line.
NEVER OVER-FILL THE DUST CUP.
CAUTION:
Unplug the vacuum; failure to do so might result in electric shock.
Bottom Door
Release
Fig. 8
Dust Cup
Release
Top Door
Release
Fig. 7
Fig. 10
Fig. 9
EMPTYING THE DUST CUP
The Dust Cup needs to be emptied each time you vacuum and periodically during cleaning, when the
Dust Cup appears full.
1
Press the dust cup release button and remove the dust cup from the vacuum. (fig. 7)
2
Option A: for Quick Empty:
Insert the Dust Cup deep inside a trash receptacle to contain the dust and debris.
Press the bottom door release button to release the trap door. Tap gently to empty contents.
(fig. 8)
Press the door shut again until it clicks.
3
Option B: For Allergy Sufferers:
Wrap a trash bag around the Dust Cup leaving space at the bottom for the door to swing open.
Locate the bottom door release button within the trash bag and press to release as you shake the dust cup to empty dust and debris. (fig. 9)
Press the door shut again until it clicks.
Note: Option B can also be performed outside of the home to further minimize releasing dust back into the air. Carry just the dust cup and trash bag outside.
4
Check to make sure the trap door is secure before returning it to the Vacuum.
5
To clean the upper compartment of the dust cup, press the top door release button to open.
(fig. 10) Empty the contents over a trash receptacle and push the door shut until it clicks into place.
www.sharkclean.com
9
NP320series_40_IB_ENG_120320_1.indd 9 12-03-20 2:48 PM
Maintenance - cont.
1
COMPONENT
Dust Cup
2
Pre-Motor Foam Filter
3
4
Pre-Motor Felt Filter
Post-Motor HEPA Filter
MAINTENANCE SCHEDULE
Empty each time you vacuum.
Rinse and air dry every month under normal use.
Rinse and air dry every month under normal use.
Clean once every 24 months under normal use.
DO NOT operate the vacuum without ALL the filters in place.
DO NOT operate the vacuum with WET filters.
DO NOT put the filters in the washing machine or dishwasher.
NOTE: The material in the filters will discolor over time. This is
NORMAL and will not affect the performance of the filters.
IMPORTANT: Loss of Suction may occur if foam filter is not cleaned every month. Rinse and allow to air dry completely. Tap loose dirt from foam filter as needed in between washing. Foam filter may appear dirty after use - this is normal.
Post Motor
HEPA Filter
Pre-Motor
Foam Filter
Felt Filter
Fig. 12
Fig. 13
Fig. 14
CLEANING THE PRE-MOTOR FILTERS
1
Remove the dust cup.
Fig. 11
the motor base. (fig. 11)
Rinse the filters thoroughly in lukewarm water until the water runs clear.
Squeeze out excess water and let air-dry for at least 24 hours before replacing. Do not use a hair dryer or other heating methods to dry.
6
Replace the dust cup.
CLEANING THE POST-MOTOR HEPA FILTER
1
Remove the tool caddy from the front of the unit.
2
Remove the filter cover from the front of the vacuum by pulling up on the tab and pulling the cover away from the vacuum. (fig. 12)
3
Take out the HEPA filter by pulling it straight out.
4
Turn the filter over so that the dirty side is on the bottom and vigorously tap it clean against a garbage can to remove any dust. (fig. 13)
5
Wash the filter under the tap using lukewarm water with the dirty side face down until the water runs clear. (fig. 14)
6
Allow the filter to air dry for 24 hours. Do not use a hair dryer or other heating methods to dry.
7
Once the HEPA filter is dry, replace it back into the vacuum.
8
Replace the cover by inserting the two tabs into the holes at the top and then swinging the cover down until it clicks into place.
10
TOLL FREE: 1-800-798-7398
NP320series_40_IB_ENG_120320_1.indd 10 12-03-20 2:48 PM
Checking for Blockages
Locking
Latch
Turbine
Wheel
Rotating
Bristle Brush
Fig. 15
Blockages may cause your vacuum to overheat and shut down. To prevent this from happening, check potential blockage areas after heavy use or if you detect a loss of suction or poor cleaning performance.
1 DUST CUP
Dust Cup may be full. Empty Dust Cup.
2 FILTERS (PRE-MOTOR AND POST MOTOR)
Ensure that both the Pre Motor Filters and the Post
Motor HEPA filter are clean.
3 ACCESSORIES
Check intake openings:
• Power Brush
• Crevice Tool
• Upholstery Brush
• Dusting Brush
• Flexible Hose
• Floor Kit Handle
• Straight Suction Nozzle
Fig. 16
CLEANING THE POWER BRUSH
• forward and tilt the cover upward to remove.
(fig. 15)
• and air passage.
• without damaging the bristles or belt, cut any build-up of hair or string wrapped around the rotating bristle brush with scissors.
• edge of the cover into the matching holes in the top half of the Power Brush and tilt the cover back down pressing until it clicks into place. (fig. 16) www.sharkclean.com
11
NP320series_40_IB_ENG_120320_1.indd 11 12-03-20 2:48 PM
Storing
Fig. 17
Resetting the Motor Thermostat
Your Shark
®
Lift-Around™ Portable Vac is equipped with a protective Motor Thermostat. If the motor should overheat, the thermostat shuts off the power.
To reset the Motor Thermostat:
Press the Power Button to turn the vacuum off.
Unplug the vacuum.
Check for clogged hose or filter; unclog hose and replace filter. Refer to Checking for Blockages.
Wait 45 minutes for vacuum to cool; then plug in the vacuum.
Press the Power Button to restart the vacuum.
Note: If vacuum still does not start, contact Customer
Service at: 1-800-798-7398.
Fig. 18
STORE YOUR VACUUM SAFELY
1
Store the dusting brush, upholstery brush, the crevice tool or the power brush on the mounts on the removable tool caddy. (fig. 17)
2
Wrap the flexible hose around the base of the vacuum and hook the end of the flexible hose into the hose dock. (fig. 18) To release the hose, press the Hose Storage button.
3
Wrap the attached cord strap around the power cord when storing.
4
Store your vacuum cleaner with the rest of the accessories safely in a cool dry area where they will not be a hazard, will not get damaged and will not cause damage to anyone or anything.
NOTE: Empty dust cup after cleaning and prior to storing. (See “Maintenance” section for instructions.)
Ordering Replacement Parts
To order additional parts and accessories, go to
www.sharkclean.com or call 1-800-798-7398.
PART
Pre-Motor Filters
HEPA Filter
Telescopic Tube
Upholstery Brush
Crevice Tool
Dusting Brush
Power Brush
Floor Kit Handle
Straight Suction Nozzle
PART NO.
XFF318
XHF318
1057FT
1061FT
1062FT
1063FT
1064FT
XKH320
XSN320
12
TOLL FREE: 1-800-798-7398
NP320series_40_IB_ENG_120320_1.indd 12 12-03-20 2:48 PM
Troubleshooting Guide
PROBLEM
Vacuum is not picking up dirt.
Airflow is restricted. No suction or light suction.
POSSIBLE REASONS & SOLUTIONS
Check Filters to see if they need cleaning. Follow instructions for rinsing and drying the Filters before re-inserting back into the Vacuum. (See “Maintenance” sections for instructions.)
Dust Cup may be full; empty Dust Cup.
Check Hose, Hose connections and accessories for blockages; clear blockages if required.
If Dust Cup is empty, and attachment inlets are clear, check for other blockages.
(See “Checking for Blockages” for instructions.)
Check Filters to see if they need cleaning. Follow instructions for rinsing and drying the Filters before re-inserting back into the Vacuum. (See “Maintenance” sections for instructions.)
Dust Cup may be full; empty Dust Cup.
Check Hose and Hose connections for suction strength; clear blockages if required.
If Dust Cup is empty, and attachment inlets are clear, check for other blockages.
(See “Checking for Blockages” for instructions.)
Vacuum turns off on its own.
This vacuum cleaner is equipped with a motor protective thermostat. If for some reason your vacuum overheats, the thermostat will automatically turn the unit off.
Should this occur, perform the following steps to restart the motor thermostat:
1. Press down on the Power Button to turn the Portable Vac off.
2. Unplug the vacuum.
3. Empty the Dust Cup and clean Filters. (See “Maintenance” sections for instructions.)
4. Check for blockages in hose, accessories and inlet opening. (See “Checking for
Blockages” for instructions.)
5. Allow the unit to cool for a minimum of 45 minutes.
6. Plug in the vacuum.
7. Press the Power Button again to restart the vacuum.
Note: If vacuum still does not start, contact Customer Service at:
1-800-798-7398.
NOTE: This appliance has no serviceable parts. Please contact Customer Service at 1-800-798-7398.
NP320series_40_IB_ENG_120320_1.indd 13 www.sharkclean.com
13
12-03-20 2:48 PM
Notes
14
TOLL FREE: 1-800-798-7398
NP320series_40_IB_ENG_120320_1.indd 14 12-03-20 2:48 PM
Euro-Pro Three-Year (3) Limited Warranty
EURO-PRO Operating LLC warrants this product to be free from defects in material and workmanship for a period of three (3) years from the date of the original purchase, when utilized for normal household use, subject to the following conditions, exclusions and exceptions.
If your appliance fails to operate properly while in use under normal household conditions within the warranty period, return the complete appliance and accessories, freight prepaid to:
• U.S.: EURO-PRO Operating LLC
For customer service support call 1-800-798-7398 or visit www.sharkclean.com
• Canada: EURO-PRO Operating LLC
4400 Bois Franc, St. Laurent, Québec H4S 1A7
If the appliance is found to be defective in material or workmanship, EURO-PRO Operating LLC will repair or replace it free of charge. Proof of purchase date and $22.95 to cover the cost of return shipping and handling must be included.*
Non-durable parts including, without limitation, filters, brushes and electrical parts which normally require replacement are specifically excluded from warranty.
The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or replacement of the unit at our option. This warranty does not cover normal wear of parts and does not apply to any unit that has been tampered with or used for commercial purposes. This limited warranty does not cover damage caused by misuse, abuse, negligent handling or damage due to faulty packaging or mishandling in transit. This warranty does not cover damage or defects caused by or resulting from damages from shipping or repairs, service or alterations to the product or any of its parts, which have been performed by a repair person not authorized by EURO-PRO Operating LLC.
This warranty is extended to the original purchaser of the unit and excludes all other legal and/or conventional warranties. The responsibility of EURO-PRO Operating LLC if any, is limited to the specific obligations expressly assumed by it under the terms of the limited warranty. In no event is EURO-PRO Operating LLC liable for incidental or consequential damages of any nature whatsoever. Some states do not permit the exclusion or limitation of incidental or consequential damages, so the above may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.
*IMPORTANT: Carefully pack item to avoid damage in shipping. Be sure to include proof of purchase date and to attach tag to item before packing with your name, complete address and phone number with a note giving purchase information, model number and what you believe is the problem with item. We recommend you insure the package (as damage in shipping is not covered by your warranty). Mark the outside of your package “ATTENTION CUSTOMER SERVICE”. We are constantly striving to improve our products, therefore the specifications contained herein are subject to change without notice.
Product Registration
Please visit www.sharkclean.com or call 1-800-798-7398 to register your new Shark
®
product within ten
(10) days of purchase. You will be asked to provide the store name, date of purchase and model number along with your name and address.
The registration will enable us to contact you in the unlikely event of a product safety notification. By registering you acknowledge to have read and understood the instructions for use, and warnings set forth in the accompanying instructions.
NP320series_40_IB_ENG_120320_1.indd 15 12-03-20 2:48 PM
Euro-Pro Operating LLC
USA: Newton, MA 02459
CAN: 4400 Bois Franc, St-Laurent, QC H4S 1A7
English: 1-800-798-7398
www.sharkclean.com
COPYRIGHT© EURO-PRO OPERATING LLC 2012
PRINTED IN CHINA
Illustrations may differ from actual product.
NP320.NP320C.E.120320.1
NP320series_40_IB_ENG_120320_1.indd 16 12-03-20 2:48 PM
advertisement
Related manuals
advertisement