Maytag WT-TOD Service manual

TECHNICAL MANU
AL
MANUAL
AMH95
40" 95% Gas Furnace
• Refer to Service Manual RS6610004 for installation, operation, and troubleshooting information.
• All safety information must be followed as provided in the Service Manual.
• Refer to the appropriate Parts Catalog for part number information.
• Model numbers listed on page 3.
®
C
This manual is to be used by qualified, professionally trained HVAC technicians only.
Goodman does not assume any responsibility for property damage or personal
injury due to improper service procedures or services performed by an unqualified
person.
is a trademark of Maytag Corporation and is used under license to Goodman Company, L.P.
All rights reserved.
®
Copyright © 2006-2007, 2009-2010 Goodman Company, L.P.
US
RT6612016 Rev. 5
April 2010
PRODUCT IDENTIFICATION
The model and manufacturing number are used for positive identification of component parts used in manufacturing.
Please use these numbers when requesting service or parts information.
A
M
H
95
045 3
B
X
A
Brand:
A
Minior
Revision
A: Amana
A: Revision
Air Flow Direction
M:Upflow/Horizontal
D: Dedicated Downflow
C: Downflow/Horizontal
H: Hi Air Flow
Major Revision
A: Initial Release
Description
NOx
H: Two-Stage/Multi-speed
V: Two-Stage/Variable-speed
N: Natural Gas
X: Low NOx
AFUE
Cabinet Width
9: 90%
95: 95%
A: 14"
B: 17 1/2"
C: 21"
D: 24 1/2"
KBTUH
045:
070:
090:
115:
140:
45,000
70,000
90,000
115,000
140,000
Maximum CFM @ 0.5" ESP
3: 1200
4: 1600
5: 2000
WARNING
HIGH VOLTAGE!
Disconnect ALL power before servicing or installing this unit. Multiple power
sources may be present. Failure to do so may cause property damage, personal
injury or death.
Goodman will not be responsible
for any injury or property damage
arising from improper service or service procedures. If
you install or perform service on this unit, you assume
responsibility for any personal injury or property damage
which may result. Many jurisdictions require a license to
install or service heating and air conditioning equipment.
WARNING
2
Installation and repair of this unit
should be performed ONLY by
individuals meeting the requirements of an "entry level technician", at a minimum, as
specified by the Air-Conditioning, Heating, and Refrigeration Institute (AHRI). Attempting to install or repair this
unit without such background may result in product
damage, personal injury or death.
WARNING
PRODUCT IDENTIFICATION
The model and manufacturing number are used for positive identification of component parts used in manufacturing.
Please use these numbers when requesting service or parts information.
AMH950453BXA*
AMH950703BXA*
AMH950704CXA*
AMH950904CXA*
AMH950905DXA*
AMH951155DXA*
WARNING
The United States Environmental Protection Agency (“EPA”) has issued various regulations regarding the introduction and disposal of refrigerants introduced into this unit. Failure to follow
these regulations may harm the environment and can lead to the imposition of substantial fines.
These regulations may vary by jurisdiction. Should questions arise, contact your local EPA office.
Do not connect or use any device
that is not design certified by
Goodman for use with this unit.
Serious property damage, personal injury, reduced unit
performance and/or hazardous conditions may result
from the use of such non-approved devices.
WARNING
To prevent the risk of property
damage, personal injury, or death,
do not store combustible materials or use gasoline or
other flammable liquids or vapors in the vicinity of this
appliance.
WARNING
3
PRODUCT DESIGN
General Operation
The AMH95 furnaces are equipped with an electronic ignition device used to light the burners and an induced draft
blower to exhaust combustion products.
An interlock switch prevents furnace operation if the blower
door is not in place. Keep the blower access door in place
except for inspection and maintenance.
This furnace is also equipped with a self-diagnosing electronic control module. In the event a furnace component is
not operating properly, the control module LED will flash on
and off in a factory-programmed sequence, depending on
the problem encountered. This light can be viewed through
the observation window in the blower access door. Refer to
the Troubleshooting Chart for further explanation of the LED
codes and Abnormal Operation - Integrated Ignition Control
section in the Service Instructions for an explanation of the
possible problem.
The rated heating capacity of the furnace should be greater
than or equal to the total heat loss of the area to be heated.
The total heat loss should be calculated by an approved
method or in accordance with “ASHRAE Guide” or “Manual
J-Load Calculations” published by the Air Conditioning Contractors of America.
*Obtain from: American National Standards Institute 1430
Broadway New York, NY 10018
3. Conversion kits for high altitude natural or propane gas
operation are available. See High Altitude Derate chart
for details.
4. Installer must supply the following gas line fittings, depending on which entrance is used:
Left -- Two 90º Elbows, one close nipple, straight pipe.
Right -- Straight pipe to reach gas valve.
Accessibility Clearances (Minimum)
MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS
(INCHES)
POSITION* FRONT SIDES REAR
TOP
FLUE FLOOR
Upflow
3
0
0
1
0
C
Horizontal
3
6
0
6
0
C
*=
All positioning is determined as installed unit is viewed from the front.
C= If placed on combustible floor, floor MUST be wood only.
NC= For instalaltion on non-combustible floors only. A non-combustible
subbase must be used for installations on combustible flooring.
24" at front is required for servicing or cleaning.
Note: In all cases accessibility clearance shall take precedence over clearances from the enclosure where accessibility clearances are greater. All dimensions are given in inches.
High Altitude Derate
Location Considerations
•
The furnace should be as centralized as is practical
with respect to the air distribution system.
•
Do not install the furnace directly on carpeting, tile, or
combustible material other than wood flooring.
•
When suspending the furnace from rafters or joists,
use 3/8" threaded rod and 2” x 2” x 3/8” angle as
shown in the Installation and Service Instructions. The
length of the rod will depend on the application and
clearance necessary.
•
When installed in a residential garage, the furnace
must be positioned so the burners and ignition source
are located not less than 18 inches (457 mm) above
the floor and protected from physical damage by vehicles.
Notes:
1. Installer must supply one or two PVC pipes: one for combustion air (optional) and one for the flue outlet (required).
Vent pipe must be either 2” or 3” in diameter, depending
upon furnace input, number of elbows, length of run and
installation (1 or 2 pipes). The optional Combustion Air
Pipe is dependent on installation/code requirements and
must be 2” or 3” diameter PVC.
2. Line voltage wiring can enter through the right or left side
of the furnace. Low voltage wiring can enter through the
right or left side of furnace.
4
When this furnace is installed at high altitude, the appropriate High Altitude orifice kit must be installed. This is required due to the natural reduction in the density of both the
gas fuel and combustion air as altitude increases. The kit
will provide the proper design certified input rate within the
specified altitude range.
P RO P ANE AND HIG H AL T IT UDE KIT S
M ODEL
NUM BER
0 to
7 ,0 0 0 ft.
LP M -0 5
AM H9 5 *****X A*
1
2
7 ,0 0 1 to
9 ,0 0 0 ft.
9 ,0 0 1 to
1 1 ,0 0 0 ft.
7 ,0 0 1 to
1 1 ,0 0 0 ft.
HANG1 2
H ig h Altitu d e
N a tu ra l G a s K it
(# 4 5 Orifice s )
HALP 1 0
H ig h Altitu d e
L P Ga s K it
(# 5 6 Orifice s )
1
HANG1 1
LP M -0 6 2
H ig h Altitu d e
P ro p a n e
N a tu ra l Ga s K it
C o n ve rs io n K it (# 4 4 O rifice s )
(# 5 5 O rifice s )
LP M -05* s upports W hite-Rodgers 2-s tage valves only
LP M -06* s upports Honey well and W hite-Rodgers 2-s tage valves
High altitude kits are purchased according to the installation altitude and usage of either natural or propane gas. Refer
to the chart above for a tabular listing of appropriate altitude
ranges and corresponding manufacturer’s high altitude Natural Gas and Propane Gas kits. For a tabular listing of appropriate altitude ranges and corresponding manufacturer's High
Altitude Pressure Switch kits, refer to either the Pressure
Switch Trip Points & Usage Chart in this manual or the Accessory Charts in Service Instructions.
COMPONENT IDENTIFICATION
Upflow/Horizontal
1
Gas Valve
17 Electrical Connection Inlets (Alternate)
2
Gas Line Entrance (Alternate)
18 Coil Front Cover Pressure Tap
3
Pressure Switch
19 Coil Front Cover Drain Port
4
Gas Manifold
20 Drain Line Penetrations
5
Combustion Air Intake Connection / “Coupling”
21 Drain Trap
6
Hot Surface Igniter
22 Blower Door Interlock Switch
7
Rollout Limit
23 Capacitor
8
Burners
24 Integrated Control Module
9
Flame Sensor
(with fuse and diagnostic LED)
10 Flue Pipe Connection / “Coupling”
25 24-Volt Thermostat Connections
11 Flue Pipe (Internal)
26 Transformer (40 VA)
12 Primary Limit
27 Circulator Blower
13 Gas Line Entrance
28 Auxiliary Limit
14 Flue Pipe Connection (Alternate)
29 Junction Box
15 Rubber Elbow
30 Electrical Connection Inlets
16 Induced Draft Blower
31 Coil Front Cover
5
COMPONENT IDENTIFICATION
AMH95*****XA*
AIR
DISCHARGE
AIR
DISCHARGE
AIR
INTAKE
PIPE
2" PVC
RIGHT SIDE
DRAIN LINE
HOLES
1 1/2
2
1 5/8
1
UNFOLDED FLANGES
UNFOLDED FLANGES
FOLDED FLANGES
FOLDED FLANGES
RIGHT SIDE VIEW
Cabinet Size
A
B
C
D
E
AMH950453BXA*
AMH950703BXA*
17-1/2
16
12-15/16
12-1/8
13-5/8
AMH950704CXA*
AMH950904CXA*
21
19-1/2
15-15/16
16
17-1/2
AMH950905DXA*
AMH951155DXA*
24-1/2
23
20-7/16
19-3/8
20-7/8
All dimensions are in inches.
6
PRODUCT DESIGN
PRESSURE SWITCH TRIP POINTS AND USAGE CHART
NEGATIVE
PRESSURE
ID BLOWER
WITH FLUE
NOT FIRING
TYPICAL
SEA
LEVEL
DATA(1)
NEGATIVE
PRESSURE
ID BLOWER
WITH FLUE
FIRING
TYPICAL
SEA
LEVE
DATA(2)
NEGATIVE
PRESSURE
COIL COVER
WITH FLUE
NOT FIRING
TYPICAL
SEA
LEVEL
DATA(1)
NEGATIVE
PRESSURE
COIL COVER
WITH FLUE
FIRING
TYPICAL
SEA
LEVE
DATA(2)
AMH950453BXA*
-1.30
-1.10
-0.52
AMH950703BXA*
-1.10
-0.95
AMH950704CXA*
-1.30
AMH950904CXA*
MODEL
PRESSURE SWITCH TRIP POINTS AND USAGE
0 to 7,000 ft.
7,001 to 11,000 ft.
TRIP POINT
COIL COVER
PRESSURE
SWITCH
COIL COVER
PRESSURE
SWITCH
PART #
TRIP POINT
ID BLOWER
PRESSURE
SWITCH
ID BLOWER
PRESSURE
SWITCH
PART #
TRIP POINT
COIL COVER
PRESSURE
SWITCH
TRIP POINT
ID BLOWER
PRESSURE
SWITCH
HIGH
ALTITUDE KIT
-0.37
-0.37
20197312
-1.10
0130F00000P
TBD
TBD
TBD
-0.52
-0.37
-0.37
20197312
-0.95
0130F00002P
TBD
TBD
TBD
-1.10
-0.52
-0.37
-0.37
20197312
-1.10
0130F00000P
TBD
TBD
TBD
-1.40
-1.20
-0.75
-0.60
-0.60
20197310
-1.20
0130F00001P
TBD
TBD
TBD
AMH950905DXA*
-1.30
-1.10
-0.52
-0.37
-0.37
20197312
-1.10
0130F00000P
TBD
TBD
TBD
AMH951155DXA*
-1.30
-1.10
-0.75
-0.60
-0.60
20197310
-1.10
0130F00000P
TBD
TBD
TBD
(1) Data given is least negative pressure required for pressure switch to close.
(2) Data given is the least negative pressure required for pressure switch to remain closed.
T.O.D. PRIMARY LIMIT
Part Number
Open Setting (°F)
20162903 20162904
160
150
1
AMH950453BXA*
AMH950703BXA*
1
AMH950704CXA*
1
1
AMH950904CXA*
AMH950905DXA*
1
AMH951155DXA*
1
7
PRODUCT DESIGN
ROLLOUT LIMIT SWITCHES
Part Number
10123514 or 10123533
Open Setting (°F)
200
AMH950453BXA*
1
AMH950703BXA*
2
AMH950704CXA*
2
AMH950904CXA*
2
AMH950905DXA*
2
AMH951155DXA*
2
AUXILIARY LIMIT SWITCHES
Part Number
10123535
10123519
Open Setting (°F)
150
160
AMH950453BXA*
1
AMH950703BXA*
1
AMH950704CXA*
1
AMH950904CXA*
1
AMH950905DXA*
1
AMH951155DXA*
8
1
PRODUCT DESIGN
Coil Matches:
A large array of Amana® brand coils are available for use with the AMH95 furnaces, in either upflow or horizontal applications. These coils are available in both cased and uncased models (with the option of a field installed TXV expansion
device). These 95%+ furnaces match up with the existing Amana® brand coils as shown in the chart below.
Coil Matches (for Goodman® units using R22 and R-410A):
C
A
P
F
1824
A
6
EXPANSION
DEVICE:
F: Flowrater
PRODUCT
TYPE:
C: Indoor Coil
CABINET FINISH:
U: Unpainted
P: Painted
N: Unpainted Case
APPLICATION
A: Upflow/Downflow Coil
H: Horizontal A Coil
S: Horizontal Slab Coil
A
REVISION
A: Revision
REFRIGERANT
CHARGE:
6: R-410A or R-22
2: R-22
4: R-410a
NOMINAL WIDTH FOR GAS FURNACE
A: Fits 14" Furnace Cabinet
B: Fits 17 1/2" Furnace Cabinet
C: Fits 21" Furnace Cabinet
D: Fits 24 1/2" Furnace Cabinet
N: Does Not Apply (Horizontal Slab Coils)
NOMINAL CAPACITY RANGE
@ 13 SEER
1824: 1 1/2 to 2 Tons
3030: 2 1/2 Tons
3636: 3 Tons
3642: 3 to 3 1/2 Tons
3743: 3 to 3 1/2 Tons
4860: 4 & 5 Tons
4961: 4 & 5 Tons
• All CAPF coils in B, C, & D widths have insulated blank off plates for use with one size smaller furnaces.
• All CAPF coils have a CAUF equivalent.
• All CHPF coils in B, C & D heights have an insulated Z bracket for use with one size smaller furnace.
• All proper coil combinations are subject to being ARI rated with a matched outdoor unit.
9
PRODUCT DESIGN
Thermostats:
NOTE: Complete lineup of thermostats can be found in the Thermostat Specification Sheets.
Filters:
Filters are required with this furnace and must be provided by the installer. The filters used must comply with UL900 or
CAN/ULCS111 standards. Installing this furnace without filters will void the unit warranty.
Upflow Filters
This furnace has provisions for the installation of return air filters at the side and/or bottom return. The furnace will
accommodate the following filter sizes depending on cabinet size:
SIDE RETURN
Approx.
Cabinet
Nominal
Width
Filter Size Flow Area
2
(in.)
(in.)
(in )
All
16 x 25 x 1
400
(1)
BOTTOM RETURN
Approx.
Cabinet
Nominal
Width
Filter Size Flow Area
2
(in.)
(in.)
(in )
17-1/2
14 x 25 x 1
350
21
16 x 25 x 1
400
24-1/2
20 x 25 x 1
500
(1) Flanges on bottom return must be unfolded
Refer to Minimum Filter Area tables to determine filter area requirement. NOTE: Filters can also be installed elsewhere in
the duct system such as a central return.
COOLING AIRFLOW REQUIREMENT (CFM)
600
800
1000
1200
1400
1600
2000
0453BXA*
388*
388*
480
576
---
---
---
0703BXA*
---
647*
647*
647*
672
---
---
0704CXA*
---
---
583*
583*
672
768
---
0904CXA*
---
---
863*
863*
863*
863*
---
0905DXA*
---
---
---
777*
777*
777*
960
1155DXA*
---
---
---
971*
971*
971*
971*
Input__Airflow
Input__Airflow
COOLING AIRFLOW REQUIREMENT (CFM)
600
800
1000
1200
1400
1600
2000
0453BXA*
194*
194*
240
288
---
---
---
0703BXA*
---
324*
324*
324*
336
---
---
0704CXA*
---
---
291*
291*
336
384
---
0904CXA*
---
---
432*
432*
432*
432*
---
0905DXA*
---
---
---
388*
388*
388*
480
1155DXA*
---
---
---
486*
486*
486*
486*
*Minimum filter area dictated by heating airflow requirement.
*Minimum filter area dictated by heating airflow requirement.
Disposable Minimum Filter Area (in2)
Permanent Minimum Filter Area (in2)
[Based on a 300 ft/min filter face velocity]
[Based on 600 ft/min filter face velocity]
10
FURNACE SPECIFICATIONS
AMH95
AMH95
0453BXA*
AMH95
0703BXA*
AMH95
0704CXA*
AMH95
0904CXA*
AMH95
0905DXA*
AMH95
1155DXA*
Input (US)
46,000
69,000
69,000
92,000
92,000
115,000
Output (US)
44,400
66,400
66,900
89,000
88,400
110,500
Input (CAN)
46,000
69,000
69,000
92,000
92,000
115,000
Output (CAN)
44,400
66,400
66,900
89,000
89,400
110,500
95.0%
95.0%
95.0%
95.0%
95.0%
95.0%
Rated External Static (" w.c.)
.20 - .50
.20 - .50
.20 - .50
.20 - .50
.20 - .50
.20 - .50
Temperature Rise (°F)
35 - 65
30 - 60
35 - 65
30 - 60
35 - 65
35 - 65
ID Blower Pressure Switch Trip Point (" w.c.)
-1.10
-0.95
-1.10
-1.20
-1.10
-1.10
Front Cover Pressure Switch Trip Point (" w.c.)
-0.37
-0.37
-0.37
-0.60
-0.37
-0.60
Blower Wheel (D" x W")
10 x 8
10 x 8
10 x 10
10 x 10
11 x 10
11 x 10
Blower Horsepower
1/3
1/3
1/2
1/2
3/4
3/4
Blower Speeds
4
4
4
4
4
4
1200
1200
1600
1600
2000
2000
115-60-1
115-60-1
115-60-1
115-60-1
115-60-1
115-60-1
9.4
9.4
13.8
13.8
13.2
13.2
15.0
15.0
15.0
15.0
15.0
15.0
Transformer (VA)
40
40
40
40
40
40
Primary Limit Setting (°F)
150
160
160
150
160
160
Auxiliary Limit Setting (°F)
150
150
150
150
150
160
Rollout Limit Setting (°F)
200
200
200
200
200
200
30 secs.
30 secs.
30 secs.
30 secs.
30 secs.
30 secs.
150 secs.
150 secs.
150 secs.
150 secs.
150 secs.
150 secs.
6 sec.
6 sec.
6 sec.
6 sec.
6 sec.
6 sec.
45 secs.
45 secs.
45 secs.
45 secs.
45 secs.
45 secs.
7 / 11
7 / 11
7 / 11
7 / 11
7 / 11
7 / 11
Manifold Pressure (Natural/Propane) ("w.c.)
3.5 / 10
3.5 / 10
3.5 / 10
3.5 / 10
3.5 / 10
3.5 / 10
Orifice Size (Natural/Propane)
43 / 55
43 / 55
43 / 55
43 / 55
43 / 55
43 / 55
2
3
3
4
4
5
2
2
2
2
2
2
2
2
2
2
2
2
132
135
136
158
172
175
MODEL
Btuh
A.F.U.E.
Max CFM @ 0.5 E.S.P.
Power Supply
(1)
Minimum Circuit Ampacity (MCA)
Maximum Overcurrent Device
(2)
Fan Delay On Heating
Off Heating
(3)
Fan Delay On Cooling
Off Cooling
Gas Supply Pressure (Natural/Propane) ("w.c.)
Number of Burners
(4)
Vent Connector Diameter (inches)
(5)
Combustion Air Connector Diameter (inches)
Shipping Weight (lbs.)
(1)
Wire size should be determined in accordance with National Electrical Codes. Extensive wire runs will require larger wire sizes.
Maximum Overcurrent Protection Device: May use Time Delay Fuse or HACR type Circuit Breaker of the same size as noted.
(3)
Off Heating - this fan delay timing is adjustable (100 and 150 seconds). Furnaces are shipped with 150 second off delay.
(4)
See Installation Instructions for appropriate vent diameter, length and number of elbows.
(5)
See Installation Instructions for appropriate combustion air pipe diameter, length and number of elbows.
(2)
NOTE: This data is provided as a guide, it is important to electrically connect the unit and properly size fuses/circuit breakers and wires in
accordance with all national and/or local electrical codes. Use copper wire only.
1. These furnaces are manufactured for natural gas operation. Optional kits are available for conversion to propane operation.
2. For elevations above 2000 feet the rating should be reduced by 4% for each 1000 feet above sea level. The furnace must not be derated, orifice changes should only
be made if necessary for altitude.
3. The total heat loss from the structure as expressed in TOTAL BTU/HR must be calculated by the manufacturers method or in accordance with the "A.S.H.R.A.E.
GUIDE" or "MANUAL J-LOAD CALCULATIONS" published by the AIR CONDITIONING CONTRACTORS OF AMERICA. The total heat loss calculated should be equal
to or less than the heating capacity. Output based on D.O.E. test procedures.
4. Minimum Circuit Ampacity calculated as: (1.25 x Circulator Blower Amps) + I.D. Blower Amps.
Unit specifications are subject to change without notice. ALWAYS refer to the units serial plate for the most up-to-date general and electrical information.
11
BLOWER PERFORMANCE SPECIFICATIONS
BLOWER PERFORMANCE
(CFM & Temperature Rise vs. External Static Pressure)
(
EXTERNAL STATIC PRESSURE (Inches Water Column)
Tons AC
Model
)
Heating Speed
As Shipped
Motor
Speed
at 0.5"
ESP
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
CFM RISE CFM RISE CFM RISE CFM RISE CFM RISE CFM CFM CFM
HIGH
3.0
1352
29
1318
30
1260
31
1202
33
1128
35
1044 955
853
AMH950453BXA*
MED
2.5
1214
32
1172
34
1123
35
1064
37
1012
39
938
859
741
(MED-HI)
MED-LO
2.0
997
40
994
40
960
41
923
43
884
45
817
741
611
LOW
1.5
757
52
753
52
734
54
704
56
674
59
620
524
438
HIGH
3.0
1449
41
1409
42
1326
45
1273
47
1201
49
1194 1136 1018
AMH950703BXA*
MED
2.5
1192
50
1172
51
1141
52
1094
54
1046
57
973
904
793
(MED-HI)
MED-LO
2.0
981
61
962
62
943
63
917
65
888
67
830
764
665
LOW
1.5
750
79
730
81
714
83
692
86
657
90
620
570
502
HIGH
4.0
2069
29
1965
30
1871
32
1756
34
1661
36
1549 1415 1275
AMH950704CXA*
MED
3.5
1752
34
1724
34
1667
36
1603
37
1488
40
1402 1290 1082
(MED-HI)
MED-LO
3.0
1437
41
1437
41
1417
42
1369
43
1320
45
1256 1140 984
LOW
2.5
1184
50
1177
50
1161
51
1132
52
1095
54
1047 928
HIGH
4.0
1970
40
1874 342 1757
45
1667
48
1566
51
1431 1334 1182
AMH950904CXA*
MED
3.5
1713
46
1650
48
1572
50
1510
52
1418
56
1313 1211 1079
(MED-HI)
MED-LO
3.0
1439
55
1412
56
1370
58
1327
60
1260
63
1166 1078 956
LOW
2.5
1183
67
1155
69
1122
74
1108
72
1062
75
1011 931
HIGH
5.0
2147
37
2114
37
2057
39
2030
39
1978
40
1889 1784 1713
AMH950905DXA*
MED
4.0
1675
47
1686
47
1640
48
1623
49
1557
51
1501 1455 1360
(MED-HI)
MED-LO
3.5
1489
53
1470
54
1436
55
1409
56
1361
58
1318 1243 1130
LOW
3.0
1307
61
1265
63
1234
64
1203
66
1168
68
1096 1053 991
HIGH
5.0
2134
46
2103
47
2029
48
1941
51
1906
51
1818 1733 1625
AMH951155DXA*
MED
4.0
1678
58
1643
60
1643
60
1577
62
1527
64
1489 1423 1339
(MED-HI)
MED-LO
3.5
1453
68
1440
68
1426
69
1363
72
1349
73
1314 1253 1205
LOW
3.0
1259
78
1239
79
1220
80
1181
83
1159
85
1118 1082 1015
837
816
1.
CFM in chart is without filters(s). Filters do not ship with this furnace, but must be provided by the installer. If the furnace requires two return
filters, this chart assumes both filters are installed.
2.
All furnaces ship as high speed cooling and medium-speed heating. Installer must adjust blower cooling & heating speed as needed.
3.
For most jobs, about 400 CFM per ton when cooling is desirable.
4.
INSTALLATION IS TO BE ADJUSTED TO OBTAIN TEMPERATURE RISE WITHIN THE RANGE SPECIFIED ON THE RATING PLATE.
5.
The chart is for information only. For satisfactory operation, external static pressure must not exceed value shown on rating plate. The shaded
area indicates ranges in excess of maximum external static pressure allowed when heating. The data for 0.6" w.c. to 0.8" w.c. is shown for
air conditioning purposes only.
6.
The above chart is for U.S. furnaces installed at 0-2000 feet. At higher altitudes, a properly de-rated unit will have approximately the same
temperature rise at a particular CFM, while the ESP at that CFM will be lower.
12
TEMPERATURE RISE
10
20
30
40
50
60
70
30
80
90
100
40
50
60
700
600 CFM
90
100
2000
2200
2400 CFM
1800
1600
1400
OUTPUT BTU/HR x 1000
80
1200
1100
1000
900
70
800
FORMULAS
110
120
130
140
BTU OUTPUT = CFM x 1.08 x RISE
BTU OUTPUT
RISE =
÷ CFM
1.08
BTU OUTPUT vs TEMPERATURE RISE CHART
150
BLOWER PERFORMANCE SPECIFICATIONS
13
WIRING DIAGRAMS
AMH95[0453,0704,0905]*XAB
AMH95[0703,0904,1155]*XAC
BLOWER
COMPARTMENT
DOOR SWITCH
(OPEN WHEN
DOOR OPEN)
OR
24 VAC
HUMIDIFIER
GY
24 VAC
INTEGRATED
CONTROL MODULE
HUMIDIFIER
TR (6)
GND
GND (8)
C
MVC (9)
115 VAC
24V THERMOSTAT
CONNECTIONS
G
C
R
BK
GY
OFF
2
1
5
4
9
8
7
BL
12
11
10
YL
2ND
STAGE
DELAY
HEAT
OFF
DELAY
*
*
HLO (1)
R
RO2 (11)
RO1 (5)
TH (3)
24 VAC
XFMR-H
115 VAC
FS
HOT SURFACE
IGNITER
IGN
HE LO
AT
-H
COOL-H
PU
BLOWER COMPARTMENT
EAC-H
MANUAL RESET
AUXILIARY LIMITS
(1) IN UPFLOW
BLOW ER DECK
(2) IN C'FLOW
BLOW ER HOUSING
BURNER COMPARTMENT
GND
BK
CIRCULATOR
BLWR
HI -H
AT
HE
OR
WH
CAPACITOR
LINE NEUTRALS
BR
YL
ID
BLWR
IND
INTEGRATED CONTROL MODULE
INTEGRATED CONTROL MODULE
OR
GY
OR
BL
BK
BR
GR
RD
PK
RD
YL
BR
W
FLAME SENSOR
WH
WH
HIGH VOLTAGE!
DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS
UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO
DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.
WH
WH
BK (HI)
BL (MED)
OR (MED LOW)
RD (LOW)
NO
C
PSO (4)
HLI (7)
BK
LINE-H
SEE
NOTE 4
PS (10)
TO
MICRO
1
HEAT-H
GND
G
Y
PK
2
115 VAC HOT AND PARK TERMINALS
COOL-H
GR
OR
115 VAC NEUTRAL
TERMINALS
XFMR-H
SEE
NOTE 6
ID BLOWER
PRESSURE
SWITCH
40 VA
TRANSFORMER
FS
*
C
NO
BR
RD
GY
OR
FACTORY SETTINGS
SHOWN
DIAGNOSTIC
LED
OR
OR
GY
*
PK
3
6
INTEGRATED
CONTROL
MODULE
24V THERMOSTAT CONNECTIONS
OR
FUSE
PM
FRONT COVER
PRESSURE SWITCH
BK
WH
BK
MODE
MVL(2)
C
W Y
ON
GAS
HI VALVE
MVH (12)
ELECTRONIC
AIR CLEANER
LINE-H
JUNCTION BOX
DOOR
SWITCH
WH
WH
INDUCED DRAFT
BLOWER
DISCONNECT
WH
PU
BL
L
YL
RD
N
O
PK
2 CIRCUIT
CONNECTOR
HOT
SURFACE
IGNITER
RD
BL
24 VAC
HUMIDIFIER
PM
N
O
C
GY
1
FRONT COVER
PRESSURE SWITCH
GY
GND
C
2
HI
3
JUNCTION
BOX
WH
GR
BK
OR
STEADY ON = NORMAL OPERATION
LOW VOLTAGE (24V)
= CONTROL FAILURE
1
1 FLASH
=
2
2 FLASHES = PRESSURE SWITCH STUCK CLOSED
HI VOLTAGE (115V)
3
3 FLASHES = PRESSURE SWITCH STUCK OPEN
HI VOLTAGE FIELD
4
4 FLASHES = OPEN HIGH LIMIT
5
5 FLASHES = FLAME SENSE WITHOUT GAS VALVE
6
6 FLASHES =
LOW VOLTAGE FIELD
7
7 FLASHES = LOW FLAME SIGNAL
8 FLASHES = CHECK IGNITER OR IMPROPER GROUNDING
CONTINUOUS/RAPID FLASHES = REVERSED 115 VAC POLARITY
0140F00592 REV. A
FIELD GND
FIELD SPLICE
JUNCTION
TERMINAL
PK PINK
BR BROWN
WH WHITE
BL BLUE
GY GRAY
RD RED
EQUIPMENT GND
SWITCH (TEMP.)
8
COLOR CODES:
YL YELLOW
OR ORANGE
PU PURPLE
GN GREEN
BK BLACK
L
FLAME
SENSOR
OFF
C
N
GND
BR
GAS VALVE
0
N
OVERCURRENT PROTECTION DEVICE
C
WH
ID BLOWER
PRESSURE
SWITCH
GND
TO 115VAC/ 1Ø /60 HZ POWER SUPPLY WITH
OR
OR
INTERNAL TO
INTEGRATED CONTROL
PLUG CONNECTION
IGNITER
SWITCH (PRESS.)
OVERCURRENT
PROT. DEVICE
NOTES:
1. SET HEAT ANTICIPATOR ON ROOM THERMOSTAT AT 0.7 AMPS.
2. MANUFACTURER'S SPECIFIED REPLACEMENT PARTS MUST BE USED WHEN SERVICING.
3. IF ANY OF THE ORIGINAL WIRE AS SUPPLIED WITH THE FURNACE MUST BE REPLACED, IT MUST BE REPLACED WITH WIRING MATERIAL
HAVING A TEMPERATURE RATING OF AT LEAST 105 °C. USE COPPER CONDUCTORS ONLY.
4. IF HEATING AND COOLING BLOWER SPEEDS ARE NOT THE SAME, DISCARD JUMPER BEFORE CONNECTING BLOWER LEADS. UNUSED
BLOWER LEADS MUST BE PLACED ON "PARK" TERMINALS OF INTEGRATED CONTROL OR TAPED.
5. UNIT MUST BE PERMANENTLY GROUNDED AND CONFORM TO N.E.C. AND LOCAL CODES.
6. TO RECALL THE LAST 5 FAULTS, MOST RECENT TO LEAST RECENT, DEPRESS SWITCH FOR MORE THAN 2 SECONDS WHILE IN
STANDBY (NO THERMOSTAT INPUTS)
Wiring is subject to change, always refer to the wiring diagram on the unit for the most up-to-date wiring.
14
WIRING DIAGRAMS
AMH95[0453,0704,0905]*XAC
AMH95[0703,0904,1155]*XAD
BLOWER
COMPARTMENT
DOOR SWITCH
(OPEN WHEN
DOOR OPEN)
OR
24 VAC
HUMIDIFIER
GY
24 VAC
C
GAS
HI VALVE
MVH (12)
PM
G
R
W
BK
G
OR
2
1
5
4
9
8
7
11
12
2ND
STAGE
DELAY
MODE
HEAT
OFF
DELAY
*
*
PK
PS (10)
BL
YL
10
HLI (7)
W
RO2 (11)
RO1 (5)
OR
MANUAL RESET ROLLOUT
LIMIT CONTROL(S)
(SINGLE CONTROL ON 45K BTU)
24 VAC
TH (3)
40 VA
TRANSFORMER
TERMINALS
FS
WH
XFMR-H
115 VAC
XFMR-H
FLAME SENSOR
PK
2
WH
FS
HOT SURFACE
IGNITER
1
115 VAC HOT AND PARK TERMINALS
HEAT-H
IGN
BK
INTEGRATED CONTROL MODULE
LINE-H
SEE
NOTE 4
MANUAL RESET AUXILIARY AUTO RESET
LIMIT CONTROLS
PRIMARY
LIMIT
CONTROL
R
GR
BR
RD
GY
OR
*
SEE
NOTE 6
GND
NO
C
PSO (4)
TO
MICRO
OR
OR
GY
FACTORY SETTINGS
SHOWN
COOL-H
ID BLOWER
PRESSURE
SWITCH
HLO (1)
OFF
DIAGNOSTIC
LED
Y
GY
3
6
C
NO
FRONT COVER
PRESSURE SWITCH
BK
WH
INTEGRATED
CONTROL
MODULE
ON
MVL(2)
C
Y
FUSE
WH
H E LO
AT
-H
COOL-H
BR
YL
ID
BLWR
IND
GY
OR
CIRCULATOR
BLOWER
BR
GR
RD
BK
BL
BR
PK
RD
YL
BK (HI)
BL (MED)
OR (MED LOW)
RD (LOW)
WH
CAPACITOR
PU
BLOWER COMPARTMENT
GND
BK
WH
INDUCED DRAFT
BLOWER
LINE-H
JUNCTION BOX
DOOR
SWITCH
WH
WARNING:
DISCONNECT POWER
BEFORE SERVICING.
WIRING TO UNIT
MUST BE
PROPERLY
POLARIZED
AND GROUNDED.
WH
AUTO RESET
PRIMARY LIMIT
CONTROL
PU
BL
C
PK
RD
HOT
SURFACE
IGNITER
0
MANUAL RESET ROLLOUT LIMIT CONTROL(S)
( SINGLE CONTROL ON 45K BTU )
24 VAC
HUMIDIFIER
PM
C
GY
1
N
O
FRONT COVER
PRESSURE SWITCH
GY
GND
C
3
HI
2
BL
JUNCTION
BOX
GND
BR
STEADY ON = NORMAL OPERATION
DISCONNECT
LOW VOLTAGE (24V)
= CONTROL FAILURE
1
1 FLASH
= SYSTEM LOCKOUT (RETRIES EXCEEDED)
2
2 FLASHES = PRESSURE SWITCH STUCK CLOSED
HI VOLTAGE (115V)
HI VOLTAGE FIELD
3
3 FLASHES = PRESSURE SWITCH STUCK OPEN
4
4 FLASHES = OPEN HIGH LIMIT
5
5 FLASHES = FLAME SENSE WITHOUT GAS VALVE
6
6 FLASHES = OPEN ROLLOUT OR OPEN FUSE
7 FLASHES = LOW FLAME SIGNAL
PK PINK
BR BROWN
WH WHITE
BL BLUE
GY GRAY
RD RED
0140F00663 REV. A
LOW VOLTAGE FIELD
EQUIPMENT GND
FIELD GND
FIELD SPLICE
SWITCH (TEMP.)
8 FLASHES = CHECK IGNITER OR IMPROPER GROUNDING
C CONTINUOUS/RAPID FLASHES = REVERSED 115 VAC POLARITY
COLOR CODES:
YL YELLOW
OR ORANGE
PU PURPLE
GN GREEN
BK BLACK
L
BK
FLAME
SENSOR
OFF
7
N
WH
GR
OR
GAS VALVE (HONEY WELL)
8
WARNING:DISCONNECT POWER BEFORE
SERVICING.WIRING TO UNIT MUST BE
PROPERLY POLARIZED AND GROUNDED.
TO 115 VAC / 1Ø / 60HZ
POWER SUPPLY WITH
OVERCURRENT PROTECTION
DEVICE
2 CIRCUIT
CONNECTOR
N
OVERCURRENT PROTECTION DEVICE
WH
ID BLOWER
PRESSURE
SWITCH
GND
TO 115VAC/ 1 Ø /60 HZ POWER SUPPLY WITH
OR
OR
N
O
DISCONNECT
L
YL
RD
ELECTRONIC
AIR CLEANER
EAC-H
MANUAL RESET
AUXILIARY LIMITS
(1) IN UPFLOW
BLOWER DECK
(2) IN C'FLOW
BLOWER HOUSING
BURNER COMPARTMENT
CIRCULATOR
BLWR
HI H
AT
HE
WH
HIGH VOLTAGE!
DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS
UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO
DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.
C
MVC (9)
115 VAC
BK
*
GND
GND (8)
40 VA
TRANSFORMER
24V THERMOSTAT
CONNECTIONS
INTEGRATED
CONTROL MODULE
HUMIDIFIER
TR (6)
JUNCTION
TERMINAL
INTERNAL TO
INTEGRATED CONTROL
PLUG CONNECTION
IGNITER
SWITCH (PRESS.)
OVERCURRENT
PROT. DEVICE
NOTES:
1. SET HEAT ANTICIPATOR ON ROOM THERMOSTAT AT 0.7 AMPS.
2. MANUFACTURER'S SPECIFIED REPLACEMENT PARTS MUST BE USED WHEN SERVICING.
3. IF ANY OF THE ORIGINAL WIRE AS SUPPLIED WITH THE FURNACE MUST BE REPLACED, IT MUST BE REPLACED WITH WIRING MATERIAL
HAVING A TEMPERATURE RATING OF AT LEAST 105 C. USE COPPER CONDUCTORS ONLY.
4. IF HEATING AND COOLING BLOWER SPEEDS ARE NOT THE SAME, DISCARD JUMPER BEFORE CONNECTING BLOWER LEADS. UNUSED
BLOWER LEADS MUST BE PLACED ON "PARK" TERMINALS OF INTEGRATED CONTROL OR TAPED.
5. UNIT MUST BE PERMANENTLY GROUNDED AND CONFORM TO N.E.C. AND LOCAL CODES.
6. TO RECALL THE LAST 5 FAULTS, MOST RECENT TO LEAST RECENT, DEPRESS SWITCH FOR MORE THAN 2 SECONDS WHILE IN
STANDBY (NO THERMOSTAT INPUTS)
Wiring is subject to change, always refer to the wiring diagram on the unit for the most up-to-date wiring.
15