Emerson BATON ROUGE CF3200DBZ00 Owner`s manual

READ AND SAVE THESE INSTRUCTIONS
BATON ROUGE
™
Ceiling Fan
Owner's Manual
Model Numbers
CF3200AWL00
CF3200DBZ00
Summer White
w/Latte Highlights
Distressed Bronze
Net Weight:
Part No. F40BP73500000
26.0 Lbs.
Form No. BP7350
U.L. Model No.: CF3200
!
WARNING
WARNING: To avoid fire, shock, and serious personal injury, follow these instructions.
Safety Instructions
1. Read your owner’s manual carefully and keep it for future reference
2. Before servicing or cleaning unit, switch power off at service panel and lock service panel
disconnecting means to prevent power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the
service panel.
3. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off
the power to the ceiling fan before servicing.
4. Do not put anything into the fan blades while they are turning.
5. Do not operate reversing switch until fan blades have come to a complete stop.
Additional Safety Instructions for Installation
1. To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not
operate fan without blades.
2. All wiring must be in accordance with the National Electrical Code “ANSI/NFPA 70-1999” and
Local Electrical Codes. Use the National Electrical Code if Local Codes do not exist. The ceiling
fan must be grounded as a precaution against possible electrical shock. Electrical installation
should be made or approved by a licensed electrician.
3. The outlet box and joist must be securely mounted an capable of reliably supporting a least 50
pounds. Use only U.L. outlet boxes listed as “Acceptable for Fan Support”, and use the mounting
screws provided with the outlet box. Most outlet boxes commonly used for support of light
fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified
electrician if in doubt.
4. The longer downrod (12”) furnished with the ceiling fan provides the minimum recommended
floor-to-fan blade clearance for a 9-foot ceiling. The 6” downrod (supplied) is to be used for
shorter ceilings.
5. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental
contact with th fan blades.
6. Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do
not know enough about electrical wiring, have your fan installed by a licensed electrician.
NOTE: This fan is suitable for use with solid-state speed controls.
WARNING: To reduce the risk of fire or electrical shock, this fan should only be used with fan
speed control, Model No. SW105, manufactured by Rhine Electric Co., Ltd.
WARNING: To avoid fire, shock or injury, do not use an Emerson or any other brand of control not
specifically approved for this fan.
WARNING: This product is designed to use only those parts supplied with this product and/or any
accessories designated specifically for use this product by Emerson Electric Co. Substitution of
parts or accessories not designated for use with this product by Emerson could result in personal
injury or property damage.
WARNING: To reduce the risk of personal injury, do not bend the blade flange when installing the
blade flanges, balancing the blades or cleaning the fan. Do not insert foreign objects in between
rotating fan blades.
WARNING: To reduce the risk of electrical shock, this fan must be installed with an isolating wall
control/switch.
DATE CODE:
The date code of this fan may be found on
the box, stamped in ink on a white label.
You should record this data above and keep
it in a safe place for future use.
2
U.L. Model No.: CF3200
This Manual Is Designed to Make it as Easy as Possible for You to
Assemble, Install, Operate and Maintain Your Ceiling Fan
Tools Needed for Assembly
Installed Wire Length
Up to 50 ft.
50-100 ft.
One stepladder
One wire stripper
One Phillips head screwdriver
Four 15-watt (max.) candelabra base bulbs
MATERIALS
WARNING
!
Wiring outlet box and box connectors must be of type
required by the local code. The minimum wire would
be a 3-conductor (2-wire with ground) of the wire
size, to right:
Wire Size A.W.G.
14
12
If you feel you do not have enough wiring knowledge or
experience, have your fan installed by a licensed
electrician.
Unpacking Instructions
For your convenience, check-off boxes are provided next to each step. As each step is completed, place
a check mark in the box. This will insure that all steps have been completed and will be helpful in finding
your place should you be interrupted.
!
5.
6.
7.
8.
9.
WARNING
Do not install or use fan if any part is damaged or
missing. Call Toll-Free:
1-800-654-3545
!
10.
11.
12.
13.
WARNING
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Electric Co. Substitution of parts or
accessories not designated for use with this product
by Emerson Electric Co. could result in personal
injury or property damage.
1. Open styrofoam unit containing fan. Remove upper
and center sections of styrofoam unit. Remove parts
and check to see that you have received the following:
a. One Fan Motor and Housing Assembly
b. One Motor Coupling Cover
c. One Ceiling Cover
d. Five Fan Blades
e. Five Flanges
f. Five Flange Medallions
g. One Hanger Ball/12” Downrod Assembly
h. One Hanger Bracket
i. One 6” Downrod
j. One Light Kit Assembly
k. One Light Kit Glass
l. One Switch Housing
m. One Decorative Downrod Cover
n. Four Decorative Scrolls
o. One Scroll Collar
p. One SW116 Fan/Light Wall Control
(transmitter) Includes Three Covers
q. One SW105 Receiver
r. One Loose Parts Bag Containing:
1. One 5/16-18 x 1/4” setscrew
2. One 5/32" hex wrench
3. Four 8-32 x 1-1/4” threaded studs
4. Four #8-32 knurled knobs
Four #8 external tooth lockwashers
Five 12 Ga. wire connectors
One hairpin clip
One clevis pin
Twenty-one 10-32 x 10mm pan head
screws
Eleven #8-32 x 14mm oval head screws
Four #8-32 x 10mm flat head screws
Five #8-32 x 15mm flat head screws
One balancing kit
NOTE: Place the parts from the loose parts bags
in small containers to keep them from being lost.
If any parts are missing, contact your local
retailer or catalog outlet for replacement before
proceeding.
a.
b.
10-32 x 10mm PAN HEAD SCREW
(4 Per Blade)
10-32 x 10mm PAN HEAD SCREW
(4 Per Blade)
10-32 x 10mm PAN HEAD SCREW
(4 Per Blade)
10-32 x 10mm PAN HEAD SCREW
FLANGE
(4 Per Blade)
10-32 x 10mm PAN HEADBLADE
SCREW ASSEMBLY
FLANGE
(4 Per Blade)
ASSEMBLY
BLADE
FLANGE
FLANGE
ASSEMBLY
MEDALLION
BLADE
FLANGE
FLANGE
ASSEMBLY
MEDALLION
BLADEFLANGE
FLANGE
ASSEMBLY
BLADE MEDALLION
FLANGE
MEDALLION
FLANGE
MEDALLION
e.
c.
d.
f.
h.
i.
j.
g.
m.
k.
l.
HIHI
LIGHT
MED
MED
n.
o.
3
LOW
LOW
REV
REV
FAN OFF
p.
q.
r.
U.L. Model No.: CF3200
IMPORTANT: Your ceiling fan is supplied with an
SW116 Fan/Light Wall Control (transmitter) and a
remote control SW105 Receiver which mounts
under the ceiling cover. This system allows you to
regulate your ceiling fan speed, airflow direction,
and light intensity. An optional Emerson Electric
SR110 Remote Control may also be used.
Ceiling Fan Assembly
Procedures
1. Place the flange assembly onto the bottom of the
blade assembly. Place the flange medallion
assembly into the four holes of the blade
assembly.
2. Secure the flange assembly and flange medallion
to the blade assembly using the four #10-32 x
10mm pan head screws. Repeat for the four
remaining blades. (Figure 1)
IMPORTANT: Your ceiling fan will not function
properly and may be damaged, if used with any
wall dimmer switch or control other than the
Emerson controls listed above.
Electrical Requirements
10-32 x 10mm PAN HEAD SCREW
(4 Per Blade)
Your new ceiling fan will require a grounded electrical
supply line of 120 volts AC, 60 Hz, 15 amp circuit.
The outlet box must be securely anchored and
capable of withstanding a load of at least 50 pounds.
!
BLADE
WARNING
FLANGE
MEDALLION
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked “Acceptable
for Fan Support”, and use screws supplied with
outlet box. Most outlet boxes commonly used for
support of light fixtures are not acceptable for fan
support and may need to be replaced. Consult a
qualified electrician if in doubt.
Figure 1
3. Place the motor housing assembly onto the
styrofoam for blade assembly installation.
4. Rotate the switch housing plate to align the holes
in the blade flange assembly with the holes in the
motor housing.
NOTE: Take care not to scratch fan housing when
installing blades.
If your fan is to replace an existing ceiling light fixture,
turn electricity off at the main fuse box at this time
and remove the existing light fixture.
!
WARNING
!
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is turned
off at the main fuse box before wiring. All wiring must
be in accordance with national and local codes and
the ceiling fan must be properly grounded as a
precaution against possible electrical shock.
!
WARNING
To reduce the risk of personal injury, do not bend the
blade flange when installing the blade flanges,
balancing the blades or cleaning the fan. Do not
insert foreign objects in between rotating fan blades.
5. Attach the flange assembly using two #8-32 x
14mm oval head screws (supplied) (Figure 2).
Install the remaining four fan blades assemblies
using the same procedure.
6. Gently snug all flange screws to the motor
housing, working around the housing in a
clockwise sequence. Next, securely tighten all
flange screws, again working in a clockwise
sequence. Failure to follow this procedure could
result in fan wobble. This completes the blade
installation.
WARNING
To avoid possible fire or shock, follow all wiring
instructions carefully. Any electrical work not
described in these instructions should be done or
approved by a licensed electrician.
Preliminary Procedures
IMPORTANT: Before assembling your ceiling fan,
refer to sections “Setting Operating Frequency of
Wall Control and Receiver” and “Installation of
Wall Control”, Page 11. These sections instruct
you how to:
a. Set the operating frequency of the fan/light wall
control and the remote control receiver.
b. Install the fan/light wall control in the wall box.
You will then be ready to proceed with the
assembly and installation of your ceiling fan.
FLANGE
ASSEMBLY
#8-32 x 14mm OVAL HEAD
SCREW (2 Per Flange Assembly)
FLANGE ASSEMBLY
MOTOR
HOUSING
4
Figure 2
U.L. Model No.: CF3200
7. Remove the wire connector from the white wire of
the switch housing plate. Retain for the next step.
8. Connect the white wire from the switch housing
plate to the white wire of the switch housing, using
the wire connector previously removed (Figure 3).
9. Connect the 9-pin connector from the switch
housing plate to the 9-pin connector of the switch
housing (Figure 3).
NOTE: If installing an optional Emerson light kit,
follow the instructions provided with the light kit.
12. Carefully turn over the partially assembled ceiling
fan and place the onto the flat surface of the
styrofoam (Figure 6).
PARTIALLY ASSEMBLED
CEILING FAN
SWITCH HOUSING
WIRE CONNECTOR
SWITCH HOUSING PLATE
WHITE WIRE
9-PIN CONNECTOR
STYROFOAM
SWITCH HOUSING
WHITE WIRE
Figure 6
NOTE: It may be necessary to remove the rubber
clips in order to install the light kit glass. Make
sure rubber clips are reinstalled so as to securely
hold the light kit glass.
Figure 3
13. Gently place the light kit glass into the decorative
light kit ring (Figure 7).
14. Rotate the rubber clips to secure glass into place.
(Figure 7). You may need to tighten the screws
on the rubber clips to secure.
10. Tuck all wires into the switch housing, opposite of
the switch housing notched hole (Figure 4).
SWITCH
HOUSING
RUBBER CLIP
SCREW
RUBBER CLIP (3)
LIGHT KIT GLASS
ALL WIRES AND
CONNECTORS
LOCATION
DECORATIVE LIGHT
KIT RING
LIGHT KIT
GLASS
SWITCH HOUSING
PLATE NOTCHED
HOLE
Figure 4
NOTE: Be sure wires are on the opposite side of
the notched hole before securing the switch
housing.
11. Secure the switch housing to the switch housing
plate using three #8-32 x 10mm flat head screws
(supplied) (Figure 5).
Figure 7
SWITCH HOUSING
#8-32 x 10mm FLAT
HEAD SCREW (3)
Figure 5
5
U.L. Model No.: CF3200
15. Securely connect the white fan one-pin connector
wire to the white one-pin connector wire from the
light kit assembly. Connect the yellow fan one-pin
connector wire to the yellow light kit assembly
one-pin connector wire (Figure 8).
LIGHT KIT
ASSEMBLY
SCREW (3)
LIGHT KIT
ASSEMBLY
NOTCHED
HOLE
KEYHOLE
SLOTS
LIGHT KIT
ASSEMBLY
YELLOW LIGHT KIT
ASSEMBLY WIRE
NOTCHED
HOLE
WHITE LIGHT KIT
ASSEMBLY WIRE
ONE-PIN
CONNECTOR
YELLOW
FAN WIRE
Figure 10
WHITE FAN WIRE
19. Obtain the hanger ball/downrod assembly and
remove the hanger ball by loosening the
setscrew in the hanger ball until the ball falls
freely down the downrod (Figure 11). Remove
the pin from the downrod, then remove the
hanger ball. Retain the pin and hanger ball for
reinstallation in Step 27. Discard the 12” downrod
if using the 6” downrod.
Figure 8
16. Install four 15-watt candelabra base light bulbs in
the light kit assembly sockets (Figure 9).
PIN
HANGER BALL
15-WATT
CANDELABRA
BASE LIGHT
BULB (4)
DOWNROD
SETSCREW
Figure 11
NOTE: The longer downrod (12”) furnished with
the ceiling fan provides the minimum
recommended floor-to-fan blade clearance for a
9-foot ceiling. The 6” downrod (supplied) is to be
used for shorter ceilings.
20. Separate, untwist and unkink the black, white and
blue motor wires and the yellow uplight lead.
Route these wires through the downrod.
21. Fold the wires from the downrod into the slot in
the motor coupling. Then slide the downrod down
the wires and seat the downrod in the motor
coupling (Figure 12).
22. Align the clevis pin holes in the downrod with the
holes in the motor coupling. Install the clevis pin
and secure with the hairpin clip (Figure 12). The
clevis pin must go through the holes in the motor
coupling and the holes in the downrod. Push the
straight leg of the hairpin clip through the hole
near the end of the clevis pin until the curved
portion of the hairpin clip snaps around the clevis
pin. The hairpin clip must be properly installed to
prevent the clevis pin from working loose.
LIGHT KIT
ASSEMBLY
SOCKET (4)
Figure 9
17. Unscrew and save one of the three screws in the
light kit adapter. Position the light kit assembly
onto the light kit adapter, making sure the wires
are positioned through a notched hole before
securing (Figure 10).
18. Rotate the light kit assembly so that the two
screws engage in the keyholes slots. Secure the
light kit assembly to the light kit adapter by
threading the previously removed screw into the
remaining hole. Tighten the three screws
securely at this time. (Figure 10).
NOTE: Do not pinch wires between the light kit
assembly and the light kit adapter.
6
U.L. Model No.: CF3200
25. Slide the motor cover over the downrod and
rotate the cover until the threaded studs protrude.
Install one lockwasher (supplied) and one knurled
knob (supplied) onto each threaded stud to
secure the cover to the motor. All wires and wire
connectors must be enclosed under the motor
cover (Figure15).
NOTE: Lightly snug the knurled knob and make
sure the wires and wire connectors are completely
inside the motor coupling cover and not pinched
between the motor coupling cover and the motor.
WARNING
!
It is critical that the clevis pin in the motor coupling
is properly installed and the setscrew securely
tightened. Failure to verify that the pin and setscrew
are properly installed could result in the fan falling.
DOWNROD
HAIRPIN
CLIP
SETSCREW
MOTOR
COUPLING
KNURLED KNOB
(1 PER STUD)
DOWNROD
MOTOR COVER
CLEVIS PIN
DOWNROD
HAIRPIN
CLIP
LOCKWASHER
(1 PER STUD)
CLEVIS PIN
THREADED STUD
MOTOR
COUPLING
Figure 15
Figure 12
IMPORTANT
A.
23. Install the setscrew (supplied) in the motor
coupling and tighten using the 5/32” setscrew
wrench (supplied) (Figure 13).
DOWNROD
HAIRPIN
CLIP
B.
SETSCREW
MOTOR
COUPLING
If you have installed the 12” or optional longer
downrod and are planning to install the
decorative scroll assembly, proceed to
“Installation of the Decorative Scroll
Assembly” on page 8. After you have installed
the decorative support rods assembly,
continue with the following installation
procedures.
If you have installed the 6” downrod, continue
now with the following procedures.
CLEVIS PIN
26. Position the ceiling cover over the downrod. Be
sure the cover is oriented correctly, with the large
opening at the top (Figure 16).
27. Reinstall the hanger ball on the downrod
as follows. Route the motor leads through the
hanger ball and slide the hanger ball over the
downrod (Figure 16). Install the pin through the
holes at the top of the downrod and slide the
hanger ball up the downrod, aligning the ball so
the pin is captured in the groove in the top of the
hanger ball. Pull the hanger ball up tight against
the pin and securely tighten the setscrew in the
hanger ball. A loose setscrew could create fan
wobble.
DOWNROD
5/32" SETSCREW
WRENCH
Figure 13
24. Screw two 1-1/4” threaded studs (supplied) into
the motor (Figure 14). Leave approximately 7/8”
of the stud extending above the motor. Coil the
wires and wire connectors around the motor
coupling.
PIN
DOWNROD
SETSCREW
HANGER
BALL
DOWNROD
CEILING
COVER
7/8"
MOTOR
COUPLING
Figure 14
7
Figure 16
U.L. Model No.: CF3200
28. The blue, black, white, and yellow leads exiting
the downrod are 80-inches long. Before installing
the fan, measure up approximately 6 to 9-inches
above the ball/downrod assembly. Cut off excess
leads and strip back insulation 1/2-inch from end
of leads.
3. Slide the assembled decorative scroll over the 12”
downrod and position each scroll leg on the
decorative light kit ring (Figure 19). Secure each of
the four decorative scroll legs using four #8-32 x
15mm flat head screws (supplied).
29. You have now completed the initial assembly of
your new ceiling fan. You can now proceed with
hanging and wiring your fan.
ASSEMBLED
DECORATIVE SCROLL
Installation of the
Decorative Scroll Assembly
#8-32 x 15mm FLAT
HEAD SCREW (1 per
leg)
DECORATIVE
LIGHT KIT RING
NOTE: The following procedures are to be
performed only if you have installed the 12” or
longer downrod.
1. Slide the decorative downrod cover over the 12”
downrod to rest upon the motor coupling cover
(Figure 17).
Figure 19
4. You have now completed the installation of the
decorative scroll assembly. Proceed to Page 7,
Step 27 to complete your ceiling fan installation.
12" DOWNROD
OR LONGER
How to Hang
Your Ceiling Fan
DECORATIVE
DOWNROD
COVER
!
WARNING
The fan must be hung with at least 7' of clearance
from floor to blades (Figure 20). Do NOT hang this
fan on an 8’ ceiling when using the 12” downrod.
MOTOR
COUPLING
COVER
CEILING
Figure 17
AT LEAST
7'
2. Remove the four screws in the scroll collar and
save for the following procedure. Assemble the
decorative scroll assembly to the scroll collar using
the previously removed screw (Figure 18).
Assemble the remaining three decorative scroll
assemblies in the same manner.
FLOOR
Figure 20
!
SCROLL COLLAR
WARNING
The outlet box and joist must be securely mounted
and capable of supporting at least 50 lbs. Use only a
U.L. outlet box listed as “Acceptable for Fan
Support”.
SCROLL COLLAR SCREWS (4)
1. Securely attach the hanger bracket to the outlet box
using the two screws supplied with the outlet box.
(Figure 21.)
DECORATIVE SCROLL
ASSEMBLY (4)
Figure 18
8
U.L. Model No.: CF3200
!
WARNING
!
Failure to seat tab in groove could cause damage to
electrical wires and possible shock or fire hazard.
To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked “Acceptable
for Fan Support”, and use screws supplied with
outlet box. Most outlet boxes commonly used for
support of light fixtures are not acceptable for fan
support and may need to be replaced. Consult a
qualified electrician if in doubt.
!
WARNING
NOTE: CEILING COVER, SUPPLY WIRES AND FAN WIRES OMITTED FOR CLARITY.
OUTLET
BOX
WARNING
Hanger bracket must seat firmly against outlet box. If
the outlet box is recessed, remove wall board until
bracket contacts box. If bracket and/or outlet box are
not securely attached, the fan could wobble or fall.
HANGER
BRACKET
OUTLET
BOX
TWO SCREWS
SUPPLIED WITH
OUTLET BOX
HANGER BALL/
DOWNROD ASSEMBLY
Figure 22
HANGER
BRACKET
Figure 21
!
TAB
WARNING
To avoid possible fire or shock, do not pinch wires
between the hanger ball/downrod assembly and the
hanger bracket.
2. Carefully lift the fan and seat the hanger
ball/downrod assembly on the hanger bracket that
was just attached to the outlet box (Figure 22). Be
sure the groove in the ball is lined up with tab on
the hanger bracket (Figure 21).
How to Wire Your Ceiling Fan
3. Using wire connectors (supplied), make wiring
connections as follows (Figure 23 and 24):
If you feel that you do not have enough electrical
wiring knowledge or experience, have your fan
installed by a licensed electrician.
!
a. Connect the white fan wire and the white supply
wire to the white receiver wire (AC IN/
MOTOR N).
b. Connect the black fan wire to the black receiver
wire (TO MOTOR L).
c. Connect the black supply wire to the black/white
receiver wire (AC IN L).
d. Cut off the ends of the blue and yellow receiver
wires and strip back insulation 1/2-inch from the
ends of the wires.
e. Connect the blue fan wire to the blue receiver
wire (BOTTOM LIGHT).
f. Connect the yellow fan wire to the yellow
receiver wire (UPPER LIGHT).
g. Connect the green ground wires from the
hanger bracket and the hanger ball to the supply
ground wire (bare or green).
WARNING
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is
turned off at the main fuse or circuit breaker box
before wiring. All wiring must be in accordance with
National and Local codes and the ceiling fan must be
properly grounded as a precaution against possible
electrical shock.
CAUTION: To reduce the risk of electrical shock,
disconnect the electrical supply circuit before
installing the fan and light kit or receiver.
1. Pull the wire leads, coming from the end of the
downrod, and the supply wires through the open
side of the hanger bracket. (Figure 23).
2. Position the SW105 Receiver (supplied) in the
ceiling cover so that the flat side of the receiver
faces up and the open portion of the receiver is to
the right, as shown in Figure 23.
9
U.L. Model No.: CF3200
OUTLET BOX
BLACK SUPPLY WIRE
HANGER BRACKET
BLACK FAN WIRE
HANGER BRACKET
GROUND WIRE
(GREEN)
OUTLET BOX
BLACK/WHITE RECEIVER WIRE
BLUE FAN WIRE
HANGER BALL
GROUND WIRE
(GREEN)
HANGER
BRACKET
BLUE RECEIVER
WIRE
1-1/4" THREADED
STUDS (2)
OPEN
PORTION OF
RECEIVER
HERE
SUPPLY GROUND
WIRE (GREEN OR
BARE)
RECEIVER
YELLOW FAN WIRE
YELLOW RECEIVER WIRE
RECEIVER
BLACK RECEIVER WIRE
WHITE SUPPLY
WIRE
WHITE RECEIVER WIRE
CEILING
COVER
WHITE FAN WIRE
CEILING COVER
WIRE CONNECTOR
Figure 23
Figure 25
SW105 RECEIVER
BLACK SUPPLY
WIRE
Final Assembly
WHITE RECEIVER WIRE
BLACK RECEIVER WIRE
BLACK/WHITE
RECEIVER WIRE
1. Screw the two 1-1/4” threaded studs (supplied) into
the tapped holes in the hanger bracket (Figure 25).
2. Lift the ceiling cover up to the threaded studs and
turn until studs protrude through the holes in the
ceiling cover (Figure 26).
3. Secure the ceiling cover in place by installing two
lockwashers and two knurled knobs (supplied)
(Figure 26). Tighten the knurled knobs securely
until the ceiling cover fits snugly against the ceiling
and the hole in the ceiling cover is clear of the
downrod.
4. Your ceiling fan in now installed and wired and
ready for use.
WHITE SUPPLY WIRE
BLUE RECEIVER WIRE
BLUE FAN WIRE
WHITE FAN WIRE
YELLOW RECEIVER WIRE
BLACK FAN WIRE
DOWNROD
CEILING
COVER
1-1/4"
THREADED
STUD (2)
Figure 24
!
WARNING
LOCKWASHER (2)
Check to see that all connections are tight, including
ground, and that no bare wire is visible at the wire
connectors, except for the ground wire. Do not
operate fan until blades are in place. Noise and fan
damage could result.
KNURLED KNOB (2)
Figure 26
!
4. After connections have been made, separate the
white and green wires from the black, blue and
yellow wires.
5. Carefully turn the wires upward and insert them up
through the open side of the hanger bracket and
into the outlet box. Push the green and white wires
into one side of the outlet box; push the black, blue
and yellow wires into the other side of the outlet
box.
WARNING
To avoid possible fire or shock, make sure that the
electrical wires are completely inside the outlet box
and not pinched between the ceiling cover and the
ceiling.
10
U.L. Model No.: CF3200
Setting Operating
Frequency of Wall Control
and Receiver (Figure 27)
Installation
of Wall Control
!
Your wall control and receiver have code switches
which must be set in one of 16 possible code
combinations. The four levers (numbered 1, 2, 3, and
4) on the switches are factory-set in the ON (up)
position. Change the switch settings as follows:
WARNING
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is
turned off at the main fuse or circuit breaker box.
The SW116 wall control transmits the command
signals via radio waves to the SW105 receiver
installed in the ceiling fan ceiling cover. The
SW105 receiver is required for the SW116 wall
control to function. Power for the SW116 wall
control comes from the 12V battery, located in the
wall control.
Replacement 12V batteries recommended are
Duracell MN21, Eveready A23, and GP23A.
1. Install the 12V battery (supplied) into the wall
control (Figure 28).
2. The SW116 wall control is supplied with a white,
ivory or almond color cover. Choose the style that
best suits your needs and snap the cover onto the
wall control (Figure 28).
1. Slide the four switch levers in the wall control to
your choice of ON (up) or down positions. Use a
ball-point pen or small screwdriver and slide the
levers firmly up or down.
2. In the receiver, slide the four switch levers to the
same positions as set in the wall control. Make
sure the levers on both switches are in the same
positions, otherwise the fan will not operate.
SW105 RECEIVER
CODE
SWITCH
HIHI
LIGHT
U/L
MED
MED
LOW
LOW
1
FAN OFF
2
3
4
WALL CONTROL
LEVERS
ON
1
REV
REV
D/L
ON
2
3
4
RECEIVER SWITCH
LEVERS
HIHI
MED
MED
LOW
LOW
Figure 28
LIGHT
12V BATTERY
SW116 WALL
CONTROL
REV
REV
3. Install the wall control onto the outlet box using the
supplied screws (Figure 29).
4. Install decorator wall plate (not included) using the
two screws provided with the wall plate. Leave wall
control in “OFF” mode until fan installation is
completed (Figure 29).
FAN OFF
SW116 WALL
CONTROL
WALL
CONTROL
COVER
CODE
SWITCH
Figure 27
DECORATIVE WALL PLATE
(Purchased Separately)
OUTLET BOX
U/L
HI
LIGHT
MED
D/L
LOW
REV
FAN OFF
Figure 29
11
WALL PLATE
SCREW (2)
SW116 WALL
CONTROL
WALL CONTROL
SCREW (2)
U.L. Model No.: CF3200
5. To turn the lights on and off, press and release the
U/L (uplight) button or the D/L (downlight) button (if
downlight kit is added to fan). The lights will turn on
at the light level previously set (see Step 4).
Red light turns on when any button is pressed.
If the light does not come on, replace your battery.
Operating Your
Ceiling Fan
IMPORTANT
Fan installation must be completed, including the
installation of the fan blades, before testing of the
remote control.
NOTE: The downlight button will not work unless
an Emerson light kit is added to the ceiling fan.
Your SW116 Fan/Light Wall Control (Figure 30) has
full control of your fan, lights, and airflow direction.
1. To set the desired fan speed, push the HI, MED, or
LOW buttons to operate your fan on high, medium
or low speed (See Figure 30).
2. To reverse the direction the fan is turning, press
the REV button. The direction the fan turns will
change each time the REV button is pressed.
3. To turn your fan off, press the FAN OFF button.
4. To set the level of light brightness, press and hold
the U/L (uplight) button or the D/L (downlight)
button (if downlight kit is added to fan). The light
brightness will continue to increase then decrease
while the button is held down. When the light is at
the desired brightness, release the button.
FAN
SPEED
BUTTONS
RED
INDICATOR
LIGHT
LIGHT
BUTTON
AIRFLOW
DIRECTION
BUTTON
U/L
HI
LIGHT
MED
D/L
FAN OFF
BUTTON
LOW
REV
FAN OFF
Figure 30
INSTRUCTION TO THE USER (if device contains a digital device)
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and if no installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is not guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This equipment has been certified to comply with the limits for a class B computing device, pursuant to FCC
Rules. In order to maintain compliance with FCC regulations, shielded cables must be used with this
equipment. Operation with non-approved equipment or unshielded cables is likely to result in interference to
radio and TV reception. The user is cautioned that changes and modifications made to the equipment without
the approval of manufacturer could void the user’s authority to operate this equipment.
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations.
12
U.L. Model No.: CF3200
Accessories
Attaching Light Kit
!
1. Ceiling Fan Light Kits (see store or catalog).
WARNING
2. Ceiling Fan/Light Controls (see store or catalog).
To avoid possible electrical shock, be sure electricity
is turned off at the main fuse box before wiring.
3. Downrod Extension Kits (see store or catalog).
To install an accessory light kit, remove the three
screws securing the switch cup assembly to the fan,
remove the switch cup assembly, and disconnect the
connector. Remove the screw plug from the bottom of
the switch cup and install the light kit in accordance
with the light kit Owner's Manual.
!
!
WARNING
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Electric Co. Substitution of parts or
accessories not designated for use with this product
by Emerson Electric Co. could result in personal
injury or property damage.
Maintenance
IMPORTANT CARE INSTRUCTIONS
for your Ceiling Fan
Periodic cleaning of your new ceiling fan is the only
maintenance that is needed.
When cleaning, use only a soft brush or lint free cloth
to avoid scratching the finish.
Abrasive cleaning agents are not required and should
be avoided to prevent damage to finish.
!
WARNING
The use of any other control not specifically
approved for this fan could result in fire, shock and
personal injury.
WARNING
Do not use water when cleaning your ceiling fan. It
could damage the motor or the blades and create the
possibility of an electrical shock.
NOTE: Periodically check the tightness of the
knurled knobs securing the light kit glass in the
light kit adapter. Tighten if necessary.
!
WARNING: For your own safety, turn off power at fuse box or circuit breaker before trouble
shooting your fan.
Trouble Shooting
TROUBLE
1. Fan will not start.
PROBABLE CAUSE
SUGGESTED REMEDY
1. Fuse or circuit breaker blown.
1. Check main and branch circuit fuses or circuit
breakers.
WARNING: Make sure main power is turned off.
2. Check line wire connections to fan
!
2. Loose power line connections to the fan.
3. Fan/Light Wall Control is OFF.
3. Turn ON Fan/Light Wall Control.
4. Code switches in remote control/receiver are not
set in the same position.
4. Check that both code switches are set in the same
positions.
2. Fan sounds noisy.
1. Blades not attached to fan.
2 Screws holding blades to flanges are loose.
1. Attach blades to fan before operating.
2. Tighten screws securely.
3. Fan wobbles
excessively.
1. Setscrew in motor coupling is loose.
2. Setscrew in hanger ball/downrod assembly is
loose.
3. Hanger bracket and/or ceiling outlet box is not
securely fastened.
4. Fan blades out of balance.
1. Raise motor cover and tighten setscrew securely.
2. Tighten the setscrew in the hanger ball/downrod
assembly.
3. Tighten the hanger bracket screws to the outlet box,
and/or secure outlet box.
4. Interchanging an adjacent (side-by-side) blade pair can
redistribute the weight and result in smoother operation.
Or use supplied balancing kit to balance blades.
13
U.L. Model No.: CF3200
Repair Parts
1
2
30
9
HIHI
LIGHT
MED
MED
LOW
LOW
6
REV
REV
FAN OFF
3
31
29
8
34
17
16
10
11
34
23
33
15
32
9
5
19
11
10
18
4
20
22
7
129
10-32 x 10mm PAN HEAD SCREW
(4 Per Blade)
21
26
BLADE
FLANGE
ASSEMBLY
24
FLANGE
MEDALLION
8
25
14
13
27
28
14
U.L. Model No.: CF3200
Repair Parts Listing
Model No.
Key
No.
Description
CF3200AWL00
CF3200DBZ00
*
1
2
3
*
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Hanger Pack, Consisting of:
Hanger Bracket
Hanger Ball
Downrod - 12”
Parts Bag Containing:
Pin, Clevis (1)
Clip, Hairpin (1)
Wire Connector, 12 Ga. (5)
Setscrew, 5/16-18 x 1/4” (1)
Setscrew Wrench, Hex. 5/32” (1)
Threaded Stud, 1-1/4” (4)
Lockwasher, External Tooth #8 (4)
Knurled Knob, #8-32 (4)
Screw, Pan Head CR #10-32 x 10mm (21)
Screw, Oval CR #8-32 x 14mm (11)
Screw, Flat Head #8-32 x 10mm (4)
Screw, Flat Head #8-32 x 15mm (5)
Balancing Kit (1)
Cover, Ceiling (1)
761655-69
—
—
—
763463-1
—
—
—
—
—
—
—
—
—
—
—
—
—
763444-AWL
761655-68
—
—
—
763463
—
—
—
—
—
—
—
—
—
—
—
—
—
763444-DBZ
18
19
20
Cover, Motor Coupling (1)
K55XL Motor (1)
Hub, Motor
761621-20
762508
760601
761621-DBZ
762508
760601
21
22
23
Housing, Upper (1)
Light Kit Assembly, Upper (1)
Glass, Upper (1)
763451-AWL
763453-AW
763452-1
763451-DBZ
763453-DBZ
763452
24
25
Flange Assembly (5 per set)
Flange Medallion Assembly (5 per set)
763455-AWL
763457-AWL
763455-DBZ
763457-DBZ
26
27
Blade Assembly (5 per set)
Harness, Wiring (1)
763459-1
763496
763459
763496
28
29
30
31
Housing, Switch (1)
Receiver, Remote Control SW105 (1)
Transmitter, Remote Control SW116 (1)
Downrod, Short 6” (1)
763462-AWL
762401
763310
761631-24
763462-DBZ
762401
763310
761631-49
32
33
34
35
Cover Decorative, Downrod (1)
Scroll Assembly, Decorative (4 per set)
Collar, Scroll (1)
Owner’s Manual
763445-AWL
763449-AWL
763448-AW
BP7350
763445-DBZ
763449-DBZ
763448-DBZ
BP7350
Before discarding packaging material, be certain all parts have been removed.
HOW TO ORDER REPAIR PARTS
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION:
• PART NUMBER
• PART DESCRIPTION
• NAME OF ITEM
• MODEL NUMBER
The model number of your Fan will be found on a label attached to the top housing.
For repair parts, phone 1-800-654-3545.
15
U.L. Model No.: CF3200
LIMITED WARRANTY
What The Warranty Covers:
This warranty covers the motor and the other components and accessories of your Emerson Electric Co. ceiling fan against
all defects in workmanship and materials. You must be the original purchaser or user of the product to be covered.
What The Period Of Coverage Is:
As it applies to the motor, this warranty will last for a lifetime from the date you purchased your ceiling fan. All other
components and accessories are covered by this warranty for one year from the date you purchased your ceiling fan. ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, MADE WITH RESPECT TO
COMPONENTS AND ACCESSORIES IS ALSO LIMITED TO ONE YEAR.
What Will Emerson Electric Co. Do To Correct Problems:
Emerson Electric Co. will replace a defective Emerson Air Comfort Ceiling Fan motor, blade, component or other accessory at
no charge to you. If repair of the motor or blades is not practical or possible within a reasonable time and no replacement
can be provided, Emerson Electric Co. will refund the actual purchase price of your fan. WE WILL SHIP THE REPAIRED
PRODUCT OR REPLACEMENT TO YOU AT NO CHARGE, BUT YOU ARE RESPONSIBLE FOR ALL COSTS OF REMOVAL,
REINSTALLATION AND SHIPPING OF THE PRODUCT TO EMERSON.
How Can You Get Service:
YOU MUST HAVE PROOF OF YOUR PURCHASE OF THE CEILING FAN TO OBTAIN LIMITED WARRANTY SERVICE. KEEP
YOUR RECEIPT OR OTHER PROOF OF PURCHASE. You can return the product to our factory or to your nearest authorized
service center.
• To return the product to the factory, obtain a return authorization and service identification tag by writing to Air Comfort
Products, Division of Emerson Electric Co., 8100 W. Florissant Ave., St. Louis, MO 63136. Include all model numbers
shown on the product with your request.
• To return the product to an authorized service center, call 1-800-654-3545 for the address of the nearest authorized
service center.
You will be responsible for all insurance, freight or other transportation charges to our factory or authorized service center.
Your Emerson Air Comfort Ceiling Fan should be properly packed to avoid damage in transit since we will not be responsible
for any such damage.
What Is Not Covered:
The glass globes and light bulbs of your ceiling fan are not covered by this warranty. This warranty also does not cover any
defects, malfunctions or failures caused by:
• Repairs by persons not authorized by Emerson Electric Co.,
• Use of parts or accessories not authorized by Emerson Electric Co.,
• Mishandling, improper installation, modifications or damage to your ceiling fan while in your possession, or
• Unreasonable use, misuse, abuse, including failing to do reasonable and necessary maintenance, and normal wear and
tear.
Additionally, this warranty and any implied warranty of merchantability or fitness for a particular purpose are voided when:
• The original purchaser or user ceases to own the product, or
• The fan is moved from its original point of installation.
This warranty is only valid within the 50 states of the United States and the District of Columbia. No other written or oral
warranties apply, and no employee, agent, dealer or other person is authorized to give any warranties on behalf of Emerson
Electric Co.
REPAIR, REPLACEMENT OR A REFUND ARE THE EXCLUSIVE REMEDIES AVAILABLE UNDER THIS WARRANTY AND
EMERSON ELECTRIC CO. IS NOT RESPONSIBLE FOR DAMAGES OF ANY KIND, INCLUDING INCIDENTAL AND
CONSEQUENTIAL DAMAGES. Incidental damages include but are not limited to such damages as loss of time and loss of
use. Consequential damages include but are not limited to the cost of repairing or replacing other property which was
damaged if this product does not work properly.
How State Law Relates To The Warranty:
Some states do not allow the exclusion or limitation of incidental or consequential damages so the above exclusion or
limitation may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.
Printed in China 11/07
Part No. F40BP73500000
Air Comfort Products
DIVISION OF EMERSON ELECTRIC CO.
8100 W. Florissant • St. Louis, MO 63136
Form No. BP7350
U.L. Model No.: CF3200