Mitsubishi Electric M900 User guide

TABLE OF CONTENTS
Page 5
Page 9
Page 13
Page 16
Page 22
Page 33
Introduction
SAR _______________________________________ 5
Declaration of conformity _______________________ 6
General safety _______________________________ 6
Vehicle safety _______________________________ 6
Emergency calls _____________________________ 7
Care and maintenance ________________________ 7
AC/DC adaptor charger ________________________ 7
Battery use _________________________________ 7
PC cable ___________________________________ 8
Your responsibility ____________________________ 8
Security Code: PIN codes ______________________ 8
Disposing of waste packaging ___________________ 8
Using this guide
Getting started
Preparing the phone for operation _______________ 12
Basic operations ____________________________ 12
Tools
Diary _____________________________________ 15
Calculator _________________________________ 18
Currency converter __________________________ 18
Alarm clocks _______________________________ 19
Infrared port ________________________________ 19
Using your mobile as a modem _________________ 20
MetaFile Exchange __________________________ 20
Messages/Text editing
Contents of the Messages menu ________________ 21
Reading a received SMS message ______________ 21
Reading stored SMS messages ________________ 21
Moving messages to SIM _____________________ 21
Forwarding messages ________________________ 22
Activating or deactivating the message alert tone ___ 22
Preparing the phone to send SMS messages ______ 22
Entering text / Edition mode ___________________ 23
Sending a new SMS message _________________ 27
Creating text models _________________________ 27
Editing a text model __________________________ 27
Signature __________________________________ 28
Outbox and SIM archive emitted messages _______ 28
Draft messages _____________________________ 28
Status request ______________________________ 28
Voice mail _________________________________ 29
Storage consumption _________________________ 30
Multimedia messages
Reading a received MMS message ______________
Saving received multimedia message content _____
Writing and sending a multimedia message _______
Filling in the multimedia message card fields ______
Preparing the phone to send MMS messages _____
Sending messages from the outbox _____________
Editing multimedia messages from the drafts folder _
Storage consumption _________________________
2- Table of Contents
31
31
32
32
34
36
36
36
Page 39
Page 43
Page 46
Page 54
Page 63
Page 71
Page 86
Page 89
Page 89
Page 90
e-mails
Reading a received e-mail _____________________ 37
Composing an e-mail _________________________ 38
Settings ___________________________________ 39
Sending an e-mail from the outbox ______________ 40
Editing e-mails from the drafts folder _____________ 40
Storage consumption _________________________ 40
Calls & times
Call logs ___________________________________ 41
Call timers _________________________________ 41
Call costs - management ______________________ 42
Recorded call _______________________________ 43
Line selection _______________________________ 43
Phone book
Storing names and telephone numbers ___________ 44
Adding a video to your Phone book card __________ 46
Adding a picture or an icon to your Phone book card 46
Setting a melody, a music or a speech note
as a ringtone
47
Editing a Phone book or a SIM name card _________ 47
Viewing and calling Phone book numbers _________ 48
Voice dialling _______________________________ 48
Free space in the Phone book __________________ 49
Creating a group of cards ______________________ 49
My card ____________________________________ 50
My number(s) display _________________________ 50
Fixed dialling numbers ________________________ 50
Export _____________________________________ 51
Camera
The Camera screen and the related icons _________ 52
Closed clamshell: scenery shots ________________ 53
Open clamshell: self-portraits ___________________ 57
Video
Video display _______________________________ 61
Closed clamshell: scenery shots ________________ 62
Open clamshell: self-filming ____________________ 66
Fun & media box
Pictures ___________________________________ 69
Melodies ___________________________________ 72
Videos ____________________________________ 73
Music _____________________________________ 75
Speech notes _______________________________ 77
Frames ____________________________________ 78
Java™ applications __________________________ 80
Others _____________________________________ 81
Storage used _______________________________ 83
miniSD™ Card
Handling and storage precautions _______________ 84
Protecting your data __________________________ 84
How to insert/extract your miniSD™ Card _________ 85
How to access the miniSD™ Card contents _______ 85
How to configure your miniSD™ Card ____________ 86
Storage used _______________________________ 86
Calendar
Network services
Wap™
Storing the connection settings _________________ 88
Starting a Wap™ session ______________________ 88
Ending the online connection ___________________ 89
Personalising your connection settings ___________ 90
Advanced settings on Wap™ profiles ____________ 92
3- Table of Contents
Page 96
Page 109
Page 114
Settings
Tones _____________________________________ 94
Display ____________________________________ 95
Keypad ___________________________________ 96
Phone settings ______________________________ 97
Connection manager _________________________ 99
GSM services _____________________________ 100
Security features ___________________________ 104
Certificates ________________________________ 105
WIM manager _____________________________ 105
Privacy ___________________________________ 106
miniSD™ Card _____________________________ 106
Appendix
Glossary _________________________________ 107
Troubleshooting ____________________________ 108
Error messages ____________________________ 109
Guarantee ________________________________ 111
Index
4- Table of Contents
INTRODUCTION
you for purchasing the M900 (GSM, DCS, PCS) mobile telephone. The mobile teleThank
phone described in this guide is approved for use on all GSM 900, DCS 1800 and PCS
1900 networks. Some of the messages displayed on your phone may be different according
to your subscription type and/or service provider.
As with all types of radio transceivers, this mobile telephone emits electromagnetic waves
and complies with international regulations when it is used under normal conditions and in
accordance with the safety and warning messages given below.
SAR
THIS M900 PHONE MEETS THE EU REQUIREMENTS FOR EXPOSURE TO RADIO
WAVES.
Before a mobile phone is available for sale to the public, compliance with the European R&TTE
directive(1999/5/EC) must be shown. This directive includes as one essential requirement the
protection of the health and the safety of the user and any other person.
Your mobile phone is a radio transmitter and receiver. It is designed and manufactured not to
exceed the limits for exposure to radiofrequency (RF) energy recommended by The Council of
the European Union1. These limits are part of the comprehensive guidelines and establish permitted
levels of RF energy for the general public. The guidelines were developed by independent scientific organisations through periodic, thorough evaluation of scientific studies. The limits include
a substantial safety margin designed to assure the safety of all persons, regardless of age and
health.
The exposure standard for mobile phones (CENELEC standard EN 50360: 2001) employs a unit
of measurement known as the Specific Absorption Rate, or SAR. The SAR limit2 recommended
by The Council of the European Union is 2.0 W/kg. Tests for SAR have been conducted using
standard operating positions (with reference to CENELEC standard EN 50361: 2001) with the
phone transmitting at its highest certified power level in all tested frequency bands3. Although
the SAR is determined at the highest certified power level, the actual SAR level of the phone
while operating can be well below the maximum value. This is because the phone is designed
to operate at multiple power levels so as to use only the power required to reach the network. In
general, the closer you are to a base station antenna, the lower the power output.
The highest SAR value for this M900 model when tested for compliance against the standard
was 0.754W/kg. While there may be differences between the SAR levels of various phones
and at various positions, they all meet the EU requirements for RF exposure.
Additional information from the World Health Organization (WHO)
Individuals: Present scientific information does not indicate the need for any special precautions for use of mobile phones. If individuals are concerned, they might choose to limit their own
or their children’s’ RF exposure by limiting the length of calls, or using "hands-free" devices to
keep mobile phones away from the head and body.
RF absorbing devices: Scientific evidence does not indicate any need for RF-absorbing
covers or other "absorbing devices" on mobile phones. They cannot be justified on health
grounds and the effectiveness of many such devices in reducing RF exposure is unproven.
Source: WHO Fact Sheet 193, June 2000.
WHO: www.who.int/peh-emf.
There are a number of independent sources of information available to users including:
Royal Society of Canada: www.rsc.ca
The International Commission on Non-Ionizing Radiation Protection (ICNIRP): www.icnirp.de
1. European recommendation 1999/519/EC
2. The SAR limit for mobile phones used by the public is 2.0 watts/kilogram (W/kg) averaged over ten
grams of tissue. The limit incorporates a substantial margin of safety to give additional protection
for the public and to account for any variations in measurements.
3. The maximum level of GSM emitted power is 250mW at 900 MHz and 125 mW at 1800 MHz
according to the GSM standard.
5- Introduction
The US Food and Drug Administration: www.fda.gov/cellphones/
The World Health Organization: www.who.int/emf
Melco Mobile Communications Europe S.A. belongs to the MMF, an international association
of radio equipment manufacturers.
The MMF produces this type of information in order to develop and present industry positions
to independent research organisations, government and other research bodies.
Mobile Manufacturers Forum
Diamant Building, 80 Blvd. A. Reyers
B-1030 Brussels Belgium
www.mmfai.org
Declaration of conformity
Melco Mobile Communications Europe S.A. hereby declares that this M900 (VGH08A) is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
A copy of the full Declaration of Conformity may be found on our website:
http://www.mitsubishi-telecom.com
General safety
Due to the possibility of radio frequency interference, it is important to follow special regulations regarding the use of radio equipment.
Please follow the safety advice given below.
Switch off your phone and remove the battery when in an aircraft. The use of mobile
telephones in an aircraft may endanger the operation of the aircraft, disrupt the mobile
phone network and is illegal.
Switch off your phone when at any refuelling point or near flammable materials.
Switch off your phone in hospitals and any other places where medical equipment may
be in use.
Respect restrictions on the use of radio equipment in fuel depots, chemical plants or
where blasting operations are in progress.
There may be a hazard associated with the operation of phones close to inadequately
protected personal medical devices such as hearing aids and pacemakers. Consult
your doctor or the manufacturers of the medical device in question to determine
whether it is adequately protected.
Operation of your phone close to other electronic equipment may also cause
interference if the equipment is inadequately protected. Observe any warning signs
and manufacturers recommendations.
Vehicle safety
Respect national regulations on the use of mobile telephones in vehicles.
Road safety always comes first! Always give your full attention to driving.
- Do not use a hand-held phone while driving. If you do not have a 'hands free' car kit, stop
and park your vehicle safely before using your phone. Please ensure that you are fully aware
of the laws in your country regarding the use of hand-held mobile devices whilst driving.
- If incorrectly installed in a vehicle, mobile telephones can interfere with the proper operation
of the vehicle electronics, such as ABS anti-lock brakes or air bags. To avoid such problems
ensure that only qualified personnel carry out the installation.
- Do not place the phone on the passenger seat or where it could fall during sudden braking
or a collision. Always use the holder.
6- Introduction
Emergency calls
You can make emergency calls by dialling the European standard emergency number 112 or
the USA emergency number 911 even if there is no SIM card in your phone. Emergency calls
can even be made if the phone is PIN or electronically locked or call barred. In some countries
local emergency numbers can still be used for emergency purposes but the phone may have
to contain a valid SIM card.
When making an emergency call remember to give all the necessary information as accurately
as possible. As the phone may be the only means of communication at the scene of an emergency, do not cut off the call until you are told to do so.
Mobile phones rely on wireless and landline networks which cannot be guaranteed in all conditions. You
should therefore never rely solely on wireless phones for essential emergency communications.
Care and maintenance
This mobile telephone is a product of advanced engineering, design and craftsmanship and
should be treated with care. Adhere to instructions below will help you to enjoy this product
for many years.
- Do not expose your phone to any extreme environment with high humidity or temperature.
- Do not expose your phone to or store your phone in cold temperatures. When the phone warms
up to its normal temperature after switch on, moisture may form inside and damage the electrical
parts.
- Do not attempt to disassemble the phone. There are no user serviceable parts inside.
- Do not expose your phone to water, rain or spilt beverages. It is not waterproof.
- Do not drop, knock or violently shake your phone. Rough handling may damage it.
- Do not clean your phone with strong chemicals or solvents. Wipe it only with a soft, slightly
dampened cloth.
- Do not place the telephone alongside computer discs, credit or travel cards or other magnetic
media. The information contained on discs or cards may be affected by the phone.
- Do not connect incompatible products. The use of third party equipment or accessories, not
made or authorised by Mitsubishi Electric, invalidates the warranty of your phone and may
be a safety risk.
- Do not remove the labels. The serial numbers on it are important for aftersales service and
other related purposes.
- Contact an authorised service centre if help is needed.
AC/DC adaptor charger
This mobile phone was designed to be used only with the supplied AC/DC charger. Use of any
other charger or adaptor invalidates any approval given to this apparatus and may be dangerous.
Battery use
Batteries may be charged hundreds of times and will gradually wear out. When the operating time
(stand-by and talk time) is noticeably shorter than normal, it is time to replace the battery.
If the battery is totally empty the battery level symbol may not be displayed at once when connecting the battery charger, moreover the phone cannot be turned on. Up to 15 minutes may be
necessary to reach the required 4% battery charge to turn your phone on and allow the battery
charge symbol to be displayed. Battery charging may only operate between 0°C and + 45°C.
- Do not leave batteries connected to a charger longer than necessary. Overcharging shortens
battery life.
- Disconnect battery chargers from the power source when not in use.
- Do not expose batteries to high temperatures or humidity.
- Do not dispose of the batteries in fire. They may explode.
- Keep batteries away from contact with metal objects which can short circuit the battery terminals
(e.g. keys, paper clips, coins, etc.).
- Do not drop or subject the batteries to strong physical shocks.
- Do not try to disassemble any of the battery packs.
- Use only the recommended battery chargers (see above).
- If the battery terminals become soiled, clean them with a soft cloth.
7- Introduction
- Batteries may warm up during charging.
Caution:
Risk of explosion if the battery is replaced by any other battery than the Mitsubishi MA-0803..
Battery disposal
In compliance with European environmental protection directives, used batteries must be
returned to the place of sale, where they are collected free of charge.
Do not dispose of your batteries within household waste.
PC cable
The PC cable enables connection of the GSM phone to a Personal Computer in order to
exchange data. The PC cable may not be supplied with your phone. Please check this
accessory availability with your retailer.
Your responsibility
This GSM mobile telephone is your responsibility. Please handle it with care and in respect
of local regulations. Please keep it in a safe place at all times and out of reach of children.
Familiarise yourself with and use the security features to block unauthorised use. If your phone
and/or SIM card are lost or stolen, call your service provider immediately to prevent illegal use.
When not in use for a prolong period of time, turn off the phone and remove the battery.
Security Code: PIN codes
The phone and SIM card are delivered to you pre-programmed with codes that protect the
phone and SIM card against unauthorised use. A short description of each follows. See “Security features” on page 104 to change your PIN and phone lock codes.
PIN and PIN2 codes (4-8 digits)
All SIM cards have a PIN (Personal Identity Number) that protects the card against unauthorised use.
Entering the wrong PIN code three times disables the SIM card and the message SIM
Blocked is then displayed. Enter your PUK code when Enter PUK: appears.
PUK and PUK2 codes (8 digits).
Please contact your service provider for your PUK code. Use it to unblock a disabled SIM card
(see “Security features” on page 104).
The PUK2 code is required to unblock the PIN2 code (see above).
Call barring password (4 digits)
This password is used to bar various types of calls, made or received, from the phone (see
“Call barring password” on page 104).
Phone lock code (4 digits)
This code is set to 0000 on delivery. You can change it. Once changed it cannot be identified by
the manufacturer over the phone. Please refer to “PIN code” on page 104 for more details.
It is advisable that you remember these codes and familiarize yourself with their purpose and operation.
Disposing of waste packaging
The packaging used for this phone is made of recyclable materials and as such should be disposed of in accordance with your country's national legislation on the protection of the environment.
Please take care to dispose the cardboard and plastic elements sepatately in the correct manner.
8- Introduction
USING THIS GUIDE
P
lease read this user guide carefully. It contains information about your phone and the way
that it operates on the network. Some of the features described in this user guide are network dependent. Do not forget to check with your service provider which of these you can use.
You may need to take out additional subscriptions to activate certain features.
Main screen / External screen
Your M900 is a clamshell-type phone with two colour display screens: an internal screen (Main
screen) and an external screen. Both screens are designed to help you enjoy clear information
about the phone and network connection status. All features described in this guide are to be
reached via the Main screen, unless otherwise specified (e.g.:features related to the Camera
and Video applications).
Key actions
To help you quickly familiarise yourself with your phone, these are the keypad and side keys
symbols used throughout the guide.
[OK] key in the middle of the cursor key (to validate OK on the display and to get direct
access to the Camera (short press) and Video (long press) applications).
Left softkey (to validate the item above (usually an action), give direct access to the
menu displayed above (short press) and to the softkey function list (long press) from the
standby display).
Right softkey (to validate the action above: usually Exit - and and give direct access to
the menu displayed above (short press) and to the softkey function list (long press) from
the standby display).
[Menu/T9] key (to access the nine icons Main menu, to switch from the T9 mode to the
Multitap mode (and vice-versa) while in edition mode.
[Phone book] key gives direct access to the Phone book list from the standby display or
the «To» field edition mode, while a call is in progress or to swap from the Phone book
names list to the SIM names list.
[Clear] key (to delete a character in edition mode.
[Right] arrow on cursor key
[Left] arrow on cursor key
[Up] arrow on cursor key
[Down] arrow on cursor key
[Send/Call] key
[End, On/Off] key
[Up] side key
[Down] side key
[Menu] side key
[Camera/Video] side key
Icons menu
The availability of the Calendar or Network services menu depends on
your SIM card.
9- Using this guide
User guide notes
Here are the instructions for using this user guide. These are examples.
The bold text stands for information displayed while using your phone.
USER GUIDE
INFORMATION TYPES
ACTIONS TO PERFORM
Press OK
Press the [Menu/T9]
key. Select Settings.
Press the
key to validate OK (middle of the display).
From the standby display press the
key to access the main menu,
scroll Up , Down, Left or Right to the Settings menu item and press
OK to access the sub-menu.
Press the
key underneath Read.
Select Read (item
above left softkey)
Select Exit (item above From the standby display press the
key underneath Exit once to
right softkey)
return to the previous screen. Press and hold
to return to the
standby screen.
Select Camera/Video Use the cursor key to scroll up, down, left or right to the required
menu item and validate by pressing OK.
E.g. ’Select Camera/Video’: scroll to the Camera/Video menu item
with the navigation keys (Up
, Down
, Left
, Right
) and
press the [OK] key to validate your selection.
Insert
The indicates that more options or sub-menus are available when
pressing OK.
...
The ... at the beginning or at the end of an Options menu indicates
that more options or sub-menus are available by scrolling up or down.
Using the dynamic scroll panels
When scrolling the menu, the following scroll panel type gives you a clear view
of the information to be entered.
1
2
3
The list of elements to be entered is displayed. Scroll down to the field(s) you want to fill in
and press OK.
Enter the requested information or select the requested item and select OK to validate.
Fill in as many fields as necessary and select Save to store all the information entered.
The arrow keys displayed at the bottom of the screen show the scrolling possibilities.
Understanding the graphic display indicators (icons)
Icons may be displayed at the top of the mobile screen.
The icons indicate the phone’s state and operational conditions when in use. The following
icons may be displayed:
SIM memory in use
Phone memory in use: refers to information from the Phone book cards.
GPRS service. Data packet services or connection are available.
GPRS connection. GPRS connection is in progress.
GPRS attached. The phone is connected to a GPRS network.
Home zone. The phone is connected to its home network.
Roaming. The phone is connected to a network other than its home
network.
Call diverting. All incoming calls are being diverted. Call diverting is
network dependent.
Alarm clock.
Vibrator alert.
Keypad lock.
10- Using this guide
Line 2. The second line is in use (subscription dependent).
Silent mode On.
Mute.
Auto-switch-off/on mode is activated.
Infrared port. The infrared port is active. i.e. that data can be received via the infrared port.
New message reception. One or more messages (SMS or MMS) have been received and
not yet read.
flashes when the reception box for SMS, MMS and e-mail is full and no
new messages can be stored. SMS, MMS and e-mail availability is network dependent.
Voice Mail. A Voice Mail message has been r eceived and stored by
the networks Voice Mail centre. Voice Mail availability is network dependent.
Outgoing Call.
Incoming Call.
Withheld number. The caller does not wish his identity to be shown.
Unanswered call. An incoming call has not been answered.
Battery level indicator. Show the current battery charge level.
Five levels are shown: from full (5 bars)
to low
(one bar). If the icon is empty,
the phone needs recharging.
Signal strength level. There are five strength levels. These show the strength of the
received signal. The more bars, the stronger the signal. If the network cannot be found, no
strength level is displayed.
Tegic edition mode.
Multitap edition mode.
Arrow keys. Indicate that more items in the menu can be accessed by pressing
or
.
Secured connection. A secured connection is in progress.
Games & Applications. software in use.
Games & Applications. A game or an application is running.
Problem in launching an application in Auto Start mode.
Application set as wallpaper. An application is set as wallpaper.
New push message. One or more push messages have been received and not yet read.
flashes when the push message box is full and no new
message can be stored. Push message availability is network dependent.
Closed user group
Written e-mail with attachment.
Read e-mail with attachment.
Sent e-mail with attachment.
E-mail to be read with attachment.
Light status
At the bottom of the external screen (please refer to Getting started with your M900) several light
colours indicate your mobile’s state (charging, event on mobile, etc.). The lights can be green,
red, yellow or blue. You can activate/deactivate these lights:
MODE
MOBILE ON
MOBILE OFF
Network available
Power saver
The green light flashes
Incoming call
The blue light flashes
Missed event (SMS,
Flashes alternately green
unanswered call, etc.) and yellow
Battery charging
The green light flashes
Battery charging over The green light flashes
No network
The red light flashes
Flashes alternately red
and yellow
The red light flashes
The red light is On
The red light iflashes
While charging, the battery charge symbol is displayed. Once charging is over, the screen backlight is turned
Off (black screen).
11- Using this guide
GETTING STARTED
Preparing the phone for operation
Please refer to the Getting started with your M900 booklet.
Basic operations
Turning the phone On
1
2
3
4
Open the clamshell.
Press and hold the [On/Off] key. A beep sounds at mobile activation. When switching the
mobile On for the first time or if the phone has been incorrectly switched off,
may be displayed.
If your SIM card is PIN protected, Enter PIN is displayed.
Enter the PIN code and select OK.
If prompted, enter the date & time or select Exit to leave existing information unchanged.
Please refer to "Security Code: PIN codes", page 8 and to "Security features", page 104 for more details on
your PIN and lock codes.
If you like to set up a Welcome screen or Welcome melody, please see "Setting a still or animated
image to standby display(for the Main screen or the External screen), as a Welcome screen or as a
Goodbye screen from the "Pictures folder" on page 71 and "Melodies" on page 72).
Making a call
The phone can make and receive calls only when it is switched on, when a valid SIM card is
inserted and when it is connected to a GSM, DCS or PCS network service.
If the keypad is locked you can receive calls but you cannot make any (see "Keypad lock" on page 14)
except emergency calls.
To make a call:
1
2
Open the clamshell.
Dial the phone number or select one from your Phone book (press the [Left] arrow key or
the Phone book key from the standby display and select a name).
3
Press the [Call/Send] key (
is displayed).
Whilst in conversation an Options list (Speaker On or Speaker Off, AutoDTMF, Hold, Retrieve, Mute or Unmute, End call and Record) and Sp.on (Speaker On)/Sp.off (Speaker Off,
after the speaker has been set to On) is available from the left and right softkeys.
You can set the conversation volume by scrolling Up and Down.
In compliance with European regulations, you are obliged to inform your correspondent before
recording a phone conversation.
Answering a call
When receiving a phone call (
1
is displayed):
Press the [Call/Send] key.
You can also answer a call by opening the clamshell. Please see "active flip", page 98.
When a phone call is received the caller name, number (see "Receiving caller ID", page 102),
picture (see "Storing names and telephone numbers", page 44) may be displayed if you created
a Phone book card corresponding to this caller.
12- Getting started
Rejecting a call
When receiving a phone call:
1
Press the [On/Off] key or close the clamshell to reject the call (the call is then forwarded to
your mailbox).
Closing the clamshell only reject the call if the Active-flip feature is activated (please see page 98).
or:
1
Press the [Camera/Video]
side key if the clamshell is closed.
Ending a call
1
Press the [On/Off] key.
You can also end a call by closing the clamshell. Please see "active flip", page 98.
To stop the ringtone when receiving a phone call
1
Press No ring if the clamshell is open or press the [Menu]
closed.
side key if the clamshell is
Holding your mobile (while making or receiving a call)
Avoid
covering the upper back of the
phone to allow
maximum emission and
reception quality.
How to hold
the phone.
When using the hands free mode, do not put the phone to your ear.
The standby display (Main screen)
When switched On, the phone searches for connection with the network. Once the
connection has been established, a beep sounds and the network and/or service
provider name or logo are displayed together with the time and date, the signal
strength and the battery charge level. If the phone cannot find a valid network, the
signal strength and the operator name are not displayed.
On the main screen, the four arrows indicate that features can be accessed via
the four arrows on the cursor key.
The camera symbol in the middle of the cursor key indicates that the Camera
application (short press) and the Video application (long press) can be accessed by pressing
the [OK] key (in the middle of the cursor key).
Message and Wap indicate that you can directly access the Messages and Wap feature by
pressing the softkeys.
The standby display (External screen)
The provider name as well as the time, the signal strength and the battery charge
levels are also displayed on the external screen when the phone is activated.
On both screens,
indicates that your phone is connected to a GPRS network.
13- Getting started
Keypad lock
When activated, the keypad lock feature prevents accidental actions occurring (e.g. camera activation) whilst the phone is being carried in a pocket or a bag for instance. Incoming calls can however be received and answered. Once the call is over, the keypad lock is automatically reactivated.
To activate the keypad lock from the standby display:
1
2
Open the clamshell.
Press and hold . Keypad locked is displayed.
To activate the keypad lock from the main menu:
1
2
3
Open the clamshell.
Press the [Menu/T9] key. Select Settings.
Select Keypad, then select Keypad lock.
To deactivate the keypad lock:
1
2
Open the clamshell.
Select Unlock and press
or press and hold
. Keypad unlocked is displayed.
Turning the phone Off
1
2
Open the clamshell.
Press and hold the [On/Off] key.
A melody sounds to confirm your action and a Goodbye screen is displayed whilst the phone
switches off. You can set a melody and/or a picture to be played/displayed when the phone is
switched off (please see "Setting a still or animated image as a standby display (for the Main
screen or the External screen), as a Welcome screen or as a Goodbye screen from the Pictures
folder", page 71 and "Melodies", page 72).
Do not take the battery out of the phone without first turning the phone off. Data might be lost. Should this
happen a first-aid kit symbol is displayed the next time the phone is activated.
Power saver
When the phone has not been used for more than one minute, the internal and external screens
turn Off (black screens). Press any key or open the clamshell to turn the internal and external
screens On.
However, this does not prevent any operation on your phone from taking place. You can therefore receive a call, an SMS, etc. whilst the internal and external screens are turned Off.
14- Getting started
TOOLS
scrolling to the Tools menu from the main icons menu, direct access to
When
the Infrared port section is possible by selecting Infrared on the left side of
the display.
The Tools menu allows access to a diary, a calculator, a currency converter,
several alarm clocks and the infrared port opening.
Diary
The Diary is divided into three parts:
-The Calendar (to manage events),
-The Tasks list (to manage tasks),
-The Storage used (to provide the diary memory information).
An event is a diary entry that has a direct implication on your timetable (e.g. a meeting).
A task is a diary entry that has no direct implication on your timetable (e.g. organising a journey).
Calendar
The calendar allows you to store up to 100 events scheduled to occur either once, daily, weekly,
monthly or yearly. Each entry can contain up to 50 characters plus a reminder alarm. Events
may be viewed on a daily, a weekly or a monthly basis, and may be sent via the Infrared port
or by SMS.
To enter an event
1
2
3
4
5
Press the [Menu/T9] key. Select Tools.
Select Diary.
Select Calendar. A Monthly or Daily view is displayed (the Daily view is displayed if an event
is related to the current day).
Select Options.
Select New event.
An empty new event card is displayed with the following fields: Title (up to 10 characters), Description (up to 50 characters), Start date & time, End date & time, Alarm, Location, Repetition.
6
7
Enter or select the requested data. Confirm each entry by pressing OK.
Select Save to confirm data storage.
To view the current day’s entries
1
2
3
4
5
Press the [Menu/T9] key. Select Tools.
Select Diary.
Select Calendar.
Select Options.
Select View... and then Today to view the current day’s entries or select
Day view to view the selected day’s entries.
In the Today view each event is displayed on one line as follows: a graphic representation ( )
if an alarm has been set, the event starting time, the first part of the event title,
Red events indicated that two or more events clash.
The following actions are available:
ACTIONS
PURPOSE
To move down to the next event or loop back to the first one
To move up to the previous event or loop to the last one
To move to the previous day
To move to the next day
An Options list is available. It allows you to change the current View..., Create a new event or
15- Tools
Modify an event, Send it by... infrared port, e-mail and SMS, Export... it, Delete one event
or Delete all events.
To view weekly entries
1
2
3
4
5
Press the [Menu/T9] key. Select Tools.
Select Diary.
Select Calendar.
Select Options.
Select View... and then Week view.
The week’s events are displayed in chronological order. Each event is represented as a bar (its
length depends on its duration. Red indicates clashes. Purple indicates that the alarm has been
activated).
The following actions are available:
ACTIONS
PURPOSE
To move down to the next time interval
To move up to the next time interval
To move to the previous day
To scroll to the previous week
To move to the following day
To scroll to the following week
(short press)
(long press)
(short press)
(long press)
An Options list is available. It allows you to change the current View..., Create an event,
Export... the Events in a defined period/All events or Delete all events.
To view monthly entries
1
2
3
4
5
Press the [Menu/T9] key. Select Tools.
Select Diary.
Select Calendar.
Select Options.
Select View... and Month view.
The whole month is displayed.
If the selected month is the current one, the date is displayed in a different colour. Colours are
used to indicate the days (and alarm activation) of the stored events.The following actions are
available:
ACTIONS
PURPOSE
(short press)
(long press)
(short press)
(long press)
To move down within the current display
To move up within the current display
To move to the previous day
To scroll to the previous month
To move to the following day
To scroll to the following month
An Options list is available. It allows you to change the current View..., Create
an event, Export... the Events in a defined period/All events or Delete all
events.
16- Tools
Tasks list
This feature allows you to store up to 100 tasks to be done (To do), scheduled with a start and
a due date, with or without a reminder alarm.
To enter a new task
1
2
3
4
Press the [Menu/T9] key. Select Tools.
Select Diary.
Select Tasks list.
Select New task and enter the required information.
An empty task card is displayed with the following fields: a title (up to 10 characters), a description (up to 50 characters), a start date, a due date, an audio alarm which can be activated at
your specified time.
5
6
Enter or select the requested data. Confirm each entry by pressing OK .
Select Save to confirm data storage.
To display a tasks list
1
2
3
4
Press the [Menu/T9] key. Select Tools.
Select Diary.
Select Tasks list .
Select Current tasks or Elapsed tasks.
The tasks are displayed in a list, ordered by date. If an alarm is activated for a task is displayed.
An Options list is available. It allows you to create a New task, Modify the current task, Send
a task by... Infrared port or by SMS, to Export... Tasks in period or All tasks, to Delete the
current task or to Delete all tasks period.
Sending an event/a task
The Send by... option allows you to directly send the selected file via the Infrared port, by SMS
or by Mail.
1
2
Press Options (from the Day, Week or Month view). Scroll down and select Send by...
Select Infrared port, SMS or Mail (if available), then proceed as usual when using these
features.
Exporting an event/a task
The Export... option allows you to create a file so as to exchange events or tasks with another
device such as a PC or another phone. The created file can contain all the events or tasks
stored in the calendar or in the tasks list (select All events/tasks) or in a time interval (Select
Events/Tasks in period).
1
2
3
Press Options (from the Day, Week or Month view). Scroll down and select Export...
Select All events/tasks or select Events/Tasks in period then define the time period
(Between / And) and select Export.
The exported file is stored in the Others folder of the Fun & Media box menu. You can then
send it to another device (please see "Others", page 83).
1. The exported calendar or tasks list item is stored as a .vcs file.
2. Once your task/event is exported to the Others folder, a confirmation screen is displayed. Then you can
directly send your task/event by selecting the Send by... option.
Alarm notification
The alarm notification screen is displayed at the specified time according to the event or task
to which it relates.
If it is not acknowledged, the alarm stops ringing after 60 seconds. It automatically restarts after a
snooze time until it is stopped or up to the start/finish time and date of the event/task. If the phone is
off at alarm time, it automatically switches on.
If the phone is locked or if the PIN setting is on, the phone returns to this locked state after the
alarm has rung until you use it.
1
Press Valid to acknowledge the alarm or press Snooze to repeat the alarm after the snooze
period.
Snooze is not available on a task alarm.
17- Tools
Storage used
This feature displays the number of Diary registered events and tasks. The following actions
are available in the Options menu:
ACTIONS
PURPOSE
Delete events
Delete tasks
Delete all events
Delete all tasks
To delete the events of the defined time period.
To delete the tasks of the defined time period.
To delete all the events stored in Calendar.
To delete the tasks stored in the Diary.
Calculator
This feature allows you to make simple calculations using + (plus), - (minus), * (multiplication),
/ (division) and % (percentage) functions.
If the currency converter is activated, numbers can be converted during calculations.
To use the calculator
1
2
Press the [Menu/T9] key. Select Tools.
Select Calculator .
The phone is ready to perform simple calculations.
Press keys
to
to enter numbers. Press the
multitap (for further details on the multitap
text entry method please see "Entering text / Edition mode", page 24) to get +, -, * and / symbols. Use the
multitap to enter decimal points or %.
Press the [Clear] key during a calculation to correct an entry. Press = to get the operation result.
Example
144 x 12 = 1728
key sequence
display
144
Press
3x
*
12
=
1728
In the above example, pressing = again calculates 1728 x 12 = 20736
Pressing the [Clear] key deletes the result.
The % function can only be used (entered) as the last operation during a calculation.
e.g.250 - 10% = 225
For instruction on setting currency converter, please see "Currency converter" on the same page for details.
using the currency converter £ - €:
Example
€ 154 + € 3 = £ 97.1374
key sequence
display
Select Curr.
95.2813
+
1.8561
=
97.1374
1. This example was made on the basis of the following exchange rate: € 1 = £0.61871
2. The Currency converter feature can be accessed from the Calculator and from the Currency converter submenus.
Currency converter
This feature allows currency conversion. The currencies and exchange rates must be entered
prior to use. The conversion is calculated on the per unit exchange rate of the second selected
currency.
18- Tools
To set up the currencies and the exchange rate
1
2
3
4
5
Press the [Menu/T9] key. Select Tools.
Select Currency converter.
Select Settings.
Enter the original currency name (e.g. Euro). Press OK.
Enter the target currency name (e.g. Dollar). Press OK.
Enter the exchange rate using
to enter a decimal point.
Press OK to validate the entry. Press Save to confirm data storage.
To calculate the conversion between the selected currencies
1
2
3
4
5
Press the [Menu/T9] key. Select Tools.
Select Currency converter.
Select the pre-defined currencies from the list.
Enter the amount to be converted. Press
to insert a decimal point if needed.
Press OK. The converted amount and the exchange rate information are displayed.
Alarm clocks
You can set up up to three different alarm clocks in your phone. They can set to be played once,
daily, or on selected days.
To set alarms
1
2
3
Press the [Menu/T9] key. Select Tools.
Select Alarm clocks.
Select Alarm 1, Alarm 2 or Alarm 3 . Select On then enter the alarm time or press OK to accept
the existing setting.
Select Repetition (1, 2 or 3 under the respective Alarm setting) to set up your repetition options.
Select Once(the alarm will be played once only), Daily (the alarm will be played every day
at the time set) or Weekdays(press OK to select the days required, then select Valid to validate
the days selected and return to the Alarm clocks screen.
is displayed in main screen after setting is completed.
If the phone is off at alarm time, it automatically switches on.
If the phone is locked or if the PIN setting is on, the phone returns to this locked state after the
alarm has rung until you use it again.
If the alarm is acknowledged but not validated after the 3rd (and final) alarm, the alarm indicators remain on the display for up to 15 minutes (the phone then either goes back its previous
state, 'on' or 'off').
1. If a call is in progress at alarm time a 'Call in progress' alert beep sounds and a visual alert is displayed
every 3 minutes. Validate or acknowledge the alarm in the usual way.
2. If several alarms are set to be played at the same time, the alarm tone is played once only. Any action performed
on the phone to acknowledge the alarm tone is then applied to all the alarms.
To use the alarm as a Reminder or a Snooze Alarm
1
Press No ring, or any other key (except Valid. and OK) to snooze the alarm. The alarm icon
remains on the display and the alarm starts ringing again 3 minutes later.
Or press Valid or OK to acknowledge the alarm and stop the alarm clock process.
To turn the alarm Off
1
2
3
Press the [Menu/T9] key. Select Tools.
Select Alarm clocks.
Select Off.
Infrared port
The infrared port allows you to exchange data between the phone and other devices (provided
they have an infrared port).
You can for instance download or send files such as videos, images for your Standby display
(see "Pictures", page 71 ), send or receive name cards,...
You can send files via the Infrared port from several menus or sub-menus (e.g. by selecting
Options after having captured a picture, then by selecting Send by... Infrared port).
19- Tools
To initiate a transfer via the infrared port, your phone must be facing another infrared port.
Both ports can then be opened and synchronised. The requested transfer can then be performed. Files (e.g name cards) are transferred one by one.
Opening the Infrared port
1
2
3
Place your phone directly opposite the infrared port of the other device.
Press the [Menu/T9] key. Select Tools.
Select Infrared port. The infrared port opens and the phone automatically acknowledges
the state of the opposite infrared port,
1. If the infrared port is already open, selecting the Infrared port item closes it.
2. The Infrared port cannot be opened while using the Camera or the Video applications. The Infrared port is automatically closed when accessing the Camera or Video applications.
Transferring a name card via the infrared port
You can transfer a name card via the infrared port:
1
2
3
4
Place your phone directly opposite the infrared port of the other device.
Open the infrared port of the other device.
Select the card you wish to transfer as explained in the section "Viewing and calling Phone
book numbers", page 50.
Select Options. Select Send by... Infrared port.
The infrared port opens and the transfer is performed.
Using your mobile as a modem
You can use your phone as a modem for other devices (PC, PDA,...) via the infrared port (on
both devices) or via a PC cable. In order to activate a connection, a standard modem driver
must already be installed in the other appliance:
1
2
3
Install the PC cable or open the infrared port on your PC or PDA.
Install the modem driver.
Configure the PC according to the instructions given with the modem driver.
Please enter the following parameters:
- Flow control: Hardware
- Data Bits: 8
- Parity: No parity
- Stop Bit: 1 stop Bit
- Speed: 921000b/s
1. The PC cable may not be supplied with your phone. Please ask your retailer for an M900 compatible PC cable.
2. The compatibility between GPRS and WAP™ features is operator dependent.
Your mobile:
1
Plug in the PC cable (please refer to the Getting Started with your M900 booklet).
1
Open your mobile Infrared port.
or:
If your phone is set to Modem mode, (Please see "Operation mode", page 102) all incoming calls are rejected.
If your phone is not set to Modem mode, your Internet connection may be interrupted by incoming calls.
Once both devices are ready, the Internet connection can be activated (without any action being
performed on your phone).
MetaFile Exchange
The MetaFile Exchange (MFE) feature allows to exchange files between the phone and the PC
via the infrared port or a PC cable :
1
2
3
Install the corresponding application on your PC (Please ask your retailer).
Install the PC cable or open the infrared port on you PC and on your phone.
Navigate in your multimedia files. You can send files from the PC to the target multimedia
folders (Pictures, Melodies, Videos, Music, Speech notes and Others) and from the multimedia folders to the PC.
The phone must be in idle state.
20- Tools
MESSAGES/TEXT EDITING
T
his section describes the features about Short Message Service under the
Messages menu.
The Short Message Service (SMS) allows you to send or receive text messages
to or from other mobile phones. You can store, edit and forward messages as well
as save any of the numbers, mail addresses, web site addresses they may
contain.
These SMS are stored on the phone memory; they may also be stored in the
SIM card if they are sent by a service provider.
You can also access the Messages menu by pressing and holding the [Mail] softkey from the
standby display.
Please refer to the MMS and Mail sections (page31 and page37) for full information on MMS
and e-mails.
Contents of the Messages menu
Your phone enable you to manage three message types: SMS,MMS and e-mails. A summary
of unread message is displayed in the Messages menu for your quick access.
To select one of these message types:
1
2
Press the [Menu/T9] key. Select Messages
Select SMS, MMS or e-mail.
A number is displayed on the SMS and MMS and e-mail lines, on the right of the screen. It
indicates the number of unread received messages in the corresponding Inbox folder.
Reading a received SMS message
When the phone receives an SMS message, a new SMS alert beep or melody sounds and
is displayed on the Standby display. The message is automatically stored in the phone or in the
SIM card. A flashing
indicates that the SIM or the phone memory are full and cannot store
any further messages. Delete messages to allow new messages to be delivered.
1
2
Press Read to read new messages (from the standby display only).
Press Options to View, Reply, Reply (+text), Delete, Delete all, Forward, Move to SIM,
Numbers & addresses (to store or call the number(s) contained in the SMS header or text,
or store the mail or web address contained in the message text. All the message characters
that are displayed between «» can also be stored on your phone).
1. According to the selected item, another Options list may be available so that you can proceed with the action.
2. If you select a melody as a new SMS alert (please see “Melodies”, page 74), press the [OK] key to acknowledge receipt of the new incoming SMS and to stop the melody.
Reading stored SMS messages
1
2
3
4
Press the [Menu/T9] key. Select Messages. Or press and hold the Mail softkey.
Select SMS.
Select Inbox or SIM archive then select Received messages to display the message list.
Use the arrow key to scroll up and down and access the message you want to read.
Select OK or Options/View to read the message text.
Unread messages are indicated by the
read are indicated by
.
icon + bold text. Messages that have already been
Moving messages to SIM
It is possible to move a message from the Inbox or the Outbox to the SIM memory. However,
according to the message size, the message may be truncated (the 160 first characters only are
moved to the SIM memory). The sending date (for sent messages) and the 'Copy to' addressees
are lost when moving the message to the SIM memory.
21- Messages/Text editing
To move a message to the SIM memory:
1
2
3
4
5
Press the [Menu/T9] key. Select Messages.
Select SMS.
Select Inbox or Outbox.
Choose the message to be moved and select Options.
Select Move to SIM.
Forwarding messages
You can forward a received message to other people/number(s):
1
2
3
4
5
6
Press the [Menu/T9] key. Select Messages.
Select SMS.
Select Inbox or SIM archive/Received messages.
Select the message to be forwarded and select Options.
Select Forward.
Press OK. Select the To field and select one of the displayed names or in the Phone book
list select Options then New or Other folder if you want to send your message to another
mobile number. Press OK to validate.
7 In the Text field enter the message text (see “Entering text / Edition mode”, page 24) or
select one of the models (Models) and press OK.
8 If you want to send the message to several addressees, enter one or several phone numbers/
names in the Copy to list (up to 4 more addressees) and press OK then Valid to return to
the previous screen.
9 Select Options.
10 Select Send, Store & send or Store.
11 A warning message displays the number of SMS needed to send the message if it is more
than one. Select Go on if you want to send the message or select Cancel if you do not want
to send it or if you want to amend your message.
Activating or deactivating the message alert tone
Each time a message is received, a new SMS alert tone sounds. To activate or deactivate this tone:
1
2
3
4
Press the [Menu/T9] key. Select Messages.
Select Parameters.
Select Reception alert.
Select On or Off. and select the requiered melody.
You can personalise the Message alert tone (please see Melodies, page 74).
Preparing the phone to send SMS messages
Before sending your first SMS or if you want to register a new profile, the network SMS centre
number (obtainable from your service provider) must be stored:
FIELDS
DESCRIPTION
DEFAULT
Name
Message centre
Format
Validity period
To enter the profile name.
To enter the centre number.
To set the message format: text, voice, fax or paging.
Time the message remains at the message centre until
delivered.
Profile1
Empty
Text
Maximum
22- Messages/Text editing
1
2
3
4
5
Press the [Menu/T9] key. Select Messages.
Select SMS.
Select Settings.
Select Sending profile.
Enter the message centre number or select a template (if several available) then enter the
following fields (operator dependent).
You may not be allowed to change your sending profile (format and validity period). Please contact your service provider for further details.
6
Select Save to validate.
The SMS centre number may already be available in your SIM card and may be automatically
displayed. If you want to select a Sending profile for your message:
1
2
3
4
5
Press the [Menu/T9] key. Select Messages.
Select SMS.
Select Settings.
Select Sending profile and select the profile you want to use. Select Options.
Select Select.
Entering text / Edition mode
All the settings described in this part are to be done from an edition screen.
Some features and functions (storing names in the Phone book, typing SMS text
messages, writing a mail, Tools, Settings,...) require you to know how to enter
and edit text in the display, to insert special characters or mail icons, to copy and
paste text, etc.
Three edition modes are available. They are indicated on the left-hand side of the
screen by
in lower case mode, by
in upper case mode and by
in next
character toggle mode (the first typed character is an upper case then the others
are lower cases). Text and figures and alphabet characters can then be entered or
edited directly from the keypad.
To switch from one mode to another:
1
2
Select Options
Select Lowercase if the current mode is upper case mode or select Uppercase if the current
mode is lower case.
When in lower case, on T9 mode or on Multi-tap mode, the Next character toggle mode is automatically set
when required, according to the context (i.e. after a full stop or after ? or ! followed by a space for instance).
There are three input modes to enter text or figures: the Multi-tap (or Multipress) key method,
the quicker intuitive method, called T9 text input and the Numeric mode (to type numbers).
To select an edition mode:
1
Press the [Menu/T9] key to swap modes (T9 to Multi-tap/Multi-tap to T9).
1
2
3
Select Options
Select Edition mode.
Select T9, Multi-tap or Numeric.
or:
When in T9 mode,
is displayed on the upper part of the display to indicate that T9 is the
current mode. When on Multitap mode,
is displayed on the upper part of the display to indicate that Multitap is the current mode.
23- Messages/Text editing
The multitap/multipress method
A brief press on a key displays the first character associated with the key and shows the other
available characters at the top of the display. Here is the list of the available characters (the
available characters list is language dependent):
KEY
CHARACTER
Lower case
Upper case
. , - ' @ : ?/_1
abc2
ABC2
def3
DEF3
ghi4
GHI4
jkl5
JKL5
mno6
MNO6
pqrs7
PQRS7
tuv8
TUV8
wxyz9
WXYZ9
0
0
Short press: Swap between the Lower case and the next character toggle mode.
Long press: Swap between the Upper case, Lower case.
Short press: to enter a space.
Long press: to access special characters.
Short press: moves the cursor through the text one place to the left or to the right.
Long press: moves the cursor to the text beginning or end.
To move the cursor to the text beginning or end.
Swap between the Multitap/Multipress method and the T9 text input.
To enter text, press the key bearing the required character until it appears in the display. Holding the key displays the figure corresponding to the key. If you need to use two characters from
the same key, wait for a few seconds after entering the first character (until the key characters
on the upper part of the screen are cleared) or press the right arrow key before pressing the
key again.
Correct mistakes by a short press on the [Clear]
key.
Holding the [Clear]
key deletes all the text. Use the left or right arrow keys to move the
cursor in the text.
Multitap method:
Example To type Card:
Press the [Menu/T9] key and select Messages.
Select SMS.
Select Write new.
Fill in the To field (see “Sending a new SMS message”, page 28).
In the Text field, press on the [Menu/T9] key until
is displayed, or select
Options, then Input mode and choose Multi-tap.
Press
briefly three times, C is displayed.
Press
until
is displayed. Press
once, a is displayed
Press
three times, r is displayed
Press
once, d is displayed. The word Card is now displayed.
24- Messages/Text editing
The T9 method
A press on the [Menu/T9] key allows you to swap between T9 text entry and the Multitap method.
1
2
3
4
5
Press the key bearing the required letter once only (the requested character may not be displayed first).
The active word changes as you enter text. Enter all the word characters up to the end of the word.
If the right word is not displayed when all the characters have been entered, press
until
you get the required word.
If the requested word does not correspond to the one displayed, press the [Menu/T9] key to
swap to the Multi-tap mode and enter the correct letters.
Use the [Left] or [Right] arrow keys to move the cursor around the text to insert or delete
characters.
Tips and Operation:
KEY
ACTION
Short press: Swap between the Lower case and the next character toggle mode.
Long press: Swap between the Upper case, Lower case.
Swap between the Multitap/Multipress method and the T9 text input.
Clear or backspace
Short press: to enter a space.
Long press: to access special characters.
Another matching word
Smart punctuation
Short press: moves the cursor to the beginning
or end
of each word.
Long press: moves the cursor to beginning
or end
of the text.
To move the cursor to the beginning or end of the text.
Example To write card:
Press the [Menu/T9] key and select Messages.
Select SMS.
Select Write new .
Fill in the To field (see “Sending a new SMS message”, page 28).
In the Text field, press on the [Menu/T9] key until
is displayed, or select
Options, then Input mode and choose T9.
Press
, A appears.
Press
, Cc appears.
Press
, Car appears.
Press , Case appears.
If the displayed word is not the one you want, press
as many times as
necessary to view Card.
To insert a text symbol such as :) or :-) or press
to change the symbol to :( or :-( etc.
two or three times. Press
as many times as necessary
Inserting special characters or text
You can insert special characters, pre-stored text models,... while using the edition mode.
Some of the elements listed below are examples and may vary according to the edition context.
To insert special characters:
1
2
Select Options, then select Insert.
Select Special characters.
Scroll up, down, left or right and press OK to select the required special
character.
or:
25- Messages/Text editing
1
2
Press and hold the
key to display the special characters list.
Scroll up, down, left or right and press OK to select the required special
character.
The ↵ symbol may not be displayed from all edition modes. It allows you to go to the following line.
To insert a text model:
1
2
3
Select Options.
Select Insert.
Select Text models. Select one from the list.
For more information on this feature, please see “Creating text models”, page 28.
This option is only available from messages edition modes (it is not available in numeric edition modes, while
writing a mail address, etc.)
Text copy and paste
You can copy a text or part of a text so as to paste it into another edition context (or into the
source edition context). The copied text remains stored in the phone memory until the phone
is turned off or until another Copy action is performed. You can therefore paste it as many times
as you wish.
To copy part of a text:
1
2
3
From an edition screen (e.g.: while writing a mail, an MMS, an SMS, a Phone book card,...),
select Options.
Select Copy (you can also access the Copy option from the edition screen by pressing the
[Up] side key).
Scroll right or left ([Right]/[Left] arrow keys or up/down side keys) to select the required part
of the text to be copied (the selected text is displayed in blue colour).
Select Copy, press OK or press the [Up] side key. The selected text is copied into the phone
memory.
1.The Copy option is not available in numeric edition modes. It is however available while using the numeric
mode in an alpha-numeric edition context.
2. The Copy all option only is available in numeric edition mode. It therefore copies the full displayed number.
To copy all the text
1
2
From an edition screen (e.g.: while writing a mail, an MMS, an SMS, a Phone book card,...),
select Options.
Select Copy all.
The whole edition screen content is copied into the phone memory.
or:
1
From an edition screen (e.g.: while writing a mail, an MMS, an SMS, a Phone book card,...),
press and hold the [Up] side key.
The whole edition screen content is copied into the phone memory.
To paste the copied text:
1
2
From an edition screen (e.g.: while writing a mail, an MMS, an SMS, a Phone book card,...),
move your cursor to the required location. Select Options.
Select Paste. The previously copied text is pasted.
or:
1
From an edition screen (e.g.: while writing a mail, an MMS, an SMS, a Phone book card,...),
move your cursor to the required location then press the [Down] side key.
1. If the copied text is too long to be inserted into the available space on the target edition mode (e.g. maximum SMS allowed size reached), the text to be copied is not fully pasted.
2. You cannot paste a copied text if the text characters are not supported by the target edition context (e.g. an
alphanumeric text in a numeric edition context, such as a text from an SMS edition screen to phone number
field).
26- Messages/Text editing
Sending a new SMS message
You can send message texts (up to 918 characters). The standard size for an SMS is 160 characters (your service provider charges you according to the number of SMS used to send your
message). The
icon (1 = number of SMS used - it is updated while writing your message
and shows the number of SMS needed to send your message) is displayed on the left corner
of the screen.
To send SMS from the Menu:
1
2
3
4
5
6
7
8
9
Press the [Menu/T9] key. Select Messages.
Select SMS.
Select Write new.
Select the To field and choose one of the displayed names, or in the Phone book list select
Options then New or Other folder if you want to send your message to another mobile
number (directly enter the number). Press OK to validate.
In the Text field, enter the message text (see “Entering text / Edition mode”, page 24) or
select one of the models (Text models ) and press OK.
If you want to send the message to several addressees, enter one or several phone numbers/names in the Copy to list (up to 4 more addressees) and press OK then Valid to
return to the previous screen.
Select Options.
Select Send, Store & send or Store.
A warning message displays the number of SMS needed to send the message if it is more
than one. Select Go on if you want to send the message or select Cancel if you do not want
to send it or if you want to amend your message.
1. If you have registered an automatic signature, the number of characters used is automatically added to the
message length.
2. Once in the phone number editor, Names allows to access the phonebook list to select a name.
3. If a name is already stored in the ’To’ list, pressing OK or one of the 0 to 9 keys again displays an Options
list (Modify: to change the selected number or e-mail address; New selection: to select a new name from the
name list; and Delete.)
4. Please go through the same process as to enter nams int the ’To’ field tho enter names in the ’Copy to’
field.
To send SMS from the standby display:
1
2
3
4
Press the [left] arrow key to access the Phone book. Scroll to one of the available names or
numbers.
Select Options.
Scroll down and select Send a message...
Select SMS, then proceed as described above.
or:
1
2
Press and hold the
key.
Select Write new, then proceed as described above.
Creating text models
You can create a set of messages to be used as models. These texts can contain up to 50 characters and text can be added when you want to use them. These templates are stored in the
phone memory. To create text models:
1
2
3
4
Press the [Menu/T9] key. Select Messages.
Select Text models.
Choose any blank template ([...]) and press OK.
Enter the template text and press OK.
Editing a text model
You can modify a text model:
1
2
3
4
Press the [Menu/T9] key. Select Messages.
Select Text models.
Select the text model to be modified and press OK.
Edit the text and press OK.
27- Messages/Text editing
Signature
You can register a signature to be automatically added to your text messages. The signature
is not displayed when typing the message text but it is displayed on message reception by the
addressee. The maximum size for the signature is 30 characters. If the message text to be sent
already contains 918 characters, the signature cannot be added.
To register a signature:
1
2
3
4
5
6
7
Press the [Menu/T9] key. Select Messages.
Select SMS.
Select Settings.
Select Signature.
Select Insert in message. Select Yes.
Select Text and enter your signature text.
Select Save to store your signature.
Outbox and SIM archive emitted messages
The Outbox contains stored sent messages (delivered or undelivered). The SIM archive contains unsent draft messages and stored sent messages (delivered or undelivered). These messages can be selected from the outbox or SIM archive menu and can be modified and resent
as new SMS messages.
To select one of these messages:
1
2
3
4
Press the [Menu/T9] key. Select Messages.
Select SMS.
Select Outbox or select SIM archive then Emitted messages and use the [Up] or [Down]
arrow keys to scroll to the required message. Messages are either 'transmitted' or 'to be sent'.
Press Options to View, Delete, Delete all (for Outbox messages only), Status (for sent
messages only) Send, Send as mail, Edit, Move to SIM (for outbox messages only), Move
to phone (for SIM archive emitted messages only), Numbers & addresses (to store or call
the number(s) contained in the SMS header or text) or Details.
Sent messages are indicated by the
ceipt are indicated by
.
icon. Sent messages that have received a return re-
Draft messages
The Drafts folder contains the written messages that were not sent. You can edit these messages
and/or send them.
To select one of these messages:
1
2
3
4
Press the [Menu/T9] key. Select Messages.
Select SMS.
Select Drafts and use the [up] or [down] arrow keys to scroll to the required message.
Press Options to View, Delete, Delete all, Send, Edit, Edit a copy, Move to SIM (for outbox messages only), Numbers & addresses (to store or call the number(s) contained in the
SMS header or text) or Details.
Written but not sent messages are indicated by the
icon.
Status request
If a status is requested on a sent message, a status request is sent to the network (must be
network supported). If the status is requested on a delivered message, the date and time of delivery may be shown. The network then answers by sending a status report (SR) back to the
phone. Press OK to acknowledge it.
28- Messages/Text editing
To activate the status request:
1
2
3
4
5
6
Press the [Menu/T9] key. Select Messages.
Select SMS.
Select Settings.
Select Message config.
Select Delivery report and select On.
Select Save.
To request a reply:
A reply to your message can be requested from your correspondent. If you activate this feature,
you will be charged for the cost of the reply message.
The availability of this feature is operator dependent.
1
2
3
4
5
6
Press the [Menu/T9] key. Select Messages.
Select SMS.
Select Settings.
Select Message config.
Select Reply requested and select On.
Select Save.
To read the sent message, delete or re-send it when receiving the status:
1
2
Press Options. Send again, Clear, Associated message or Delete message is displayed.
Select the required action.
Voice mail
Your network provider may offer a Voice Mail service which operates like an answering machine.
You may be able to access it directly by pressing and holding the .
Contact your service provider for further details.
Storing a voice mail centre number
If your SIM card does not contain the Voice Mail centre number, you must store it manually:
1
2
2
3
4
Press the [Menu/T9] key. Select Messages.
Select Parameters.
Select Voice Mail.
Select Number. Enter the number (either by keying it or selecting Options then Names list).
Press OK to validate.
1. The Voice Mail number is automatically assigned to speed dial location number 1 (see “Speed dial”, page 99).
2. If you subscribe to the 'Line 2' service, an additional Voice Mail centre number must be stored separately.
Activating/deactivating the voice mail alert tone
If you wish to be advised by a tone when receiving a new Voice Mail message:
1
2
2
3
Press the [Menu/T9] key. Select Messages.
Select Parameters.
Select Voice Mail.
Select Alert. Select On.
The availability of this feature is operator dependent.
Calling the voice mail centre to check your messages
You can either:
- Dial the Voice Mail centre number directly after receiving a message:
1
From the standby display, press and hold
1
2
2
3
Press the [Menu/T9] key. Select Messages.
Select Parameters.
Select Voice Mail.
Select Call.
.
- or:
29- Messages/Text editing
Storage consumption
The storage status for SMS messages can be consulted.
To view the number of messages stored, the total available space on the Phone memory and
on the SIM card:
1
2
3
4
Press the [Menu/T9] key. Select Messages.
Select SMS.
Select Storage used. The SMS memory used is displayed. Scroll down to access the SIM
archive.
Select Details for more information on the Phone and SIM stored messages (use [up] and
[down] arrow keys to scroll to the required information).
30- Messages/Text editing
MULTIMEDIA MESSAGES
The Multimedia Messages Service (MMS) is a service that allows the sending
and receiving of messages to and from other MMS enabled mobile phones. The
main difference between an SMS and an MMS is the MMS is composed of one
or several pages made of text + image(s) and sounds (melody, MP3 files, videos or speech notes).
The reception quality of a Multimedia message content may vary depends on the addressee's
mobile phone.
The protocol that is used to transfer the multimedia messages is the Wap™ protocol; you therefore
need a Data subscription (see "Wap™", page 90) to send and receive multimedia messages.
The sending and receiving of a Multimedia message imply the launching of a connection via an
MMS centre. Please contact your service provider to get full information on the subscription
conditions.
The receiving of a Multimedia message implies two steps:
- The receiving of a message notification bearing (optionnally) the sender’s name, the message
subject and size and its validity duration on the MMS centre.
- The retrieval of the corresponding message from the network (on request).
Multimedia message(s) may already be stored in your phone at mobile first use. This depends
on your service provider.
Reading a received MMS message
When the phone receives an MMS a new alert tone sounds and
or the New message
information is displayed.
If
flashes, it indicates the SIM or the phone memory are full and cannot store any other
messages. Delete SMS or Multimedia messages to allow new messages to be delivered.
1
2
3
Press Read to read your new message(s) or message notification(s).
When receiving a message notification choose whether or not to retrieve the Multimedia
message from the network (select Options then Retrieve message and Yes).
Scroll down to
if your message bears several pages and select OK.
The notification and the retrieved message are automatically stored in the Inbox.
1
2
3
4
Press the [Menu/T9] key. Select Messages.
Select MMS.
Select Inbox to display the MMS list. Use the arrow keys to scroll up and down and reach
the message you want to read.
Selecting Options allows access to View, Reply, Reply all, Reply by SMS (please see
"Sending a new SMS message", page 28), Delete, Delete all, Forward, Numbers &
Addresses (to store the number(s) and/or e-mail address contained in the MMS header)
and Details (to view the Multimedia message header contents).
Select OK or Options/View to read the message.
1. You cannot modify the contents of a received Multimedia message.
2. if the selected message is a notification the available options are: Retrieve message, Reject, Delete, Delete
all, Numbers & Addresses and Details.
3. if the selected message is a delivery report the available options are: View, Delete, Delete all and Numbers
& Addresses.
4. An ’Attachment’ option is available while viewing the selected message. You can then store the message
attached files
Unread messages are shown by
and the text is bold. Messages that have been already read
are shown by
.
Multimedia message notifications are shown by
and delivery messages by
.
31- Multimedia Messages
Saving received multimedia message content
You can store the images, melodies, videos, events, tasks and speech notes attached to the received multimedia messages into the Fun & media box. When reading a received Multimedia
message:
1 Select Options.
2
3
4
Select Attachment.
Select Options.
Select Store.
According to the attached item the Options sub-menu allows to view or store the attachment contents.
Writing and sending a multimedia message
To write a Multimedia message:
1
2
3
4
5
Press the [Menu/T9] key. Select Messages .
Select Multimedia messages.
Select Write new.
Fill in the required information in the Multimedia card (please see below) and select Options.
Select Send, Send & Store, Store or Adjust config. before sending the message and
press OK.
The Adjust config. settings (to require a delivery report, a read reply report, to add a priority level or a delivery
time to your message) only apply to the edited message before they are sent. The Message config. parameters are the default settings (see " Setting multimedia messages characteristics", page 35).
Filling in the multimedia message card fields
In the Multimedia card (see " Writing and sending a multimedia message" above) the following
fields have to be filled in:
To
You can send your message to several people (main addressees plus ’Copy to’ addressees).
Please check the maximum number with your service provider.
1
2
3
Selecting OK gives direct access to the phonebook.
Choose one of the displayed names or select New if you want to send your message to another
phone number or e-mail address (directly type the number or address in). You can also press
any of the 0 to 9 keys to type a new phone number or an e-mail address.
Select an empty item [...] to add another addressee or select Valid. to get back to the Multimedia
card.
1. If the selected phonebook card contains several data you are requested to choose one from the stored
numbers or e-mail addresses (e.g. home number, e-mail address,...).
2. If a name is already stored in the ’To’ list, pressing OK or one of the 0 to 9 keys again displays an Options
list (Modify: to change the selected number or e-mail address; New selection: to select a new name from the
name list; Delete and Delete all.)
3. To add names in the Copy to field, the process is the same as for the To field.
Subject
Type in your message subject text (40 characters max.). Please see "Entering text / Edition
mode", page 23.
The subject text is displayed in the message notification sent to the addressee (if supported by the
addressee’s phone).
Content
The following screen is displayed (it allows you to edit your message pages):
Displayed symbols (upper part of the screen):
The previous page can be reached by pressing the left arrow key.
The next page can be reached by pressing the right arrow key.
One or several pages can be added next by pressing the right arrow
key.
Remaining space (displayed dynamically while composing the
message).
32- Multimedia Messages
Estimated message size (displayed dynamically while composing the
message).
Current page number.
A melody is attached to the current page.
A speech note is attached to the current page.
A music file is attached to the current page.
The black squared field shows the active field (Pictures or Text fields). Press the down arrow
key to scroll to the next field and select OK to edit it.
To attach an image or a video
You can attach images to your Multimedia message. These images have to be .jpg, .gif (animated
or not animated), or .wbmp.
The size of the Multimedia messages you can send is operator dependent. However, by default,
the maximum size cannot exceed 100 Kb.
1
2
2
When on the picture field press OK.
Select Video or Picture.
Select one of the available videos or pictures from the list and press OK or press Options then
Camera or Video to take a new picture.
The selected image or video is partly displayed in the picture field.
1. You can send any of the Pictures or videos unless the file is copyright protected (the ’File protected’ message is
then displayed).
2. The ’No picture’ or ’No video’ item from the Pictures list or Video list allows to delete the current page
image.
3. ’Too many data for message sending’ is displayed on image selection if its size exceeds the message sending
capacity.
To attach a melody, a music or a speech note
You can attach melodies, music (MP3 melodies) and speech notes to your Multimedia message.
The size of the Multimedia messages you can send is operator dependent. However the maximum size cannot exceed 100 Kb.
1
2
When on the picture field or on the text field, select Options.
Select Add sound then select Melodies, Music or Speech notes. Select the required melodies or speech note in the displayed list.
The selected melody
, music
or speech note
is attached to the message.
1. You can send any of the Melodies or Speech notes unless the file is copyright protected (the ’File protected’
message is then displayed).
2. ’Too many data for message sending’ is displayed on melody or speech note selection if its size exceeds
the message sending capacity.
3. It is not possible to add a sound when a video is already included in the current page.
To write text
1
2
Select the text field.
Type in your page text (240 characters per page max.): please see "Entering text / Edition
mode", page 23.
Press OK or select Models (left softkey), then choose one of the displayed messages.
1.’Too many data for message sending’ is displayed on text insertion if its size exceeds the message sending
capacity.
2. You can amend the Models text once you have selected one.
3. You cannot insert a Chinese text model if your mobile edition mode is set to English.
To edit and modify the page contents
1
Select Options. The following list is displayed:
OPTION
ACTION
Validate
To validate the informations of the Content field and get back to the message
composer.
Page
To modify the text size (Small, Nomal or Large), the text colour, the background
options
colour and set the page timer (default timer = 3 seconds). The timer allows to set
the time the page is displayed before switching to the following one.
Add sound To add a melody from the Melodies list, a MP3 melody from the Music list or a
speech note from the Speech notes list.
33- Multimedia Messages
Delete
sound
Invert
layout
Insert page
Delete page
Preview
message
To delete the page attached Melody, Music or Speech note.
To invert the text and the image location on the page.
To insert a new page or duplicate the current page (9 pages maximum).
To delete the current page.
To view the full message contents.
1. The ’Too many data for message sending’ message is displayed on image, melody, music, video, speech
note and text selection if the size of the selected file exceeds the message sending capacity
2. The ’validate’ option is not available when you only have one empty page in your Content field.
3. The contents of this Options menu depends on the contents of the current page.
2
Select Exit to come back to the composition of the MMS or select Validate to come back to
the card fields.
Do not forget to check the message size before sending it (see the estimated size in the right upper corner of
the screen).
To add one or several pages
1
2
Press the right arrow key on the last page of your message.
Select New page.
1
2
3
Select Options.
Scroll down to Insert page and press OK.
Select New page.
or
A Multimedia message can be up to 9 pages.
To duplicate a page
You may need to duplicate a page in order to modify its contents for instance. The new page bears
the same characteristics (e.g: text colour) which allows to save time when writing a Multimedia
message.
1
2
Press right arrow key on the last page of your message.
Select Duplicate page.
1
2
3
Press Options.
Scroll down to Insert page and press OK.
Select Duplicate page.
or
To delete the page content
1
Select Clear to come back to an empty Multimedia card.
If the selected page is already empty selecting Clear leads to the ’Delete page’ action.
Name card
The name card field allows to attach a copy of a vcard to the multimedia message.
1
2
Select the Name card list
Select a name in the phonebook. A copy of the vcard is then attached to the message
1. If there is already an attached vcard, pressing OK displays the Modify and Delete options.
2. The selected card is automatically renamed if it contains Chinese characters.
Copy to
Please see the ’To’ section on page 32.
34- Multimedia Messages
Preparing the phone to send MMS messages
The Multimedia Message service is subscription and network dependent. The operator profile
details may already be stored on your phone. If not, please contact your service provider to get
them.
The profile list can contain up to 3 MMS profiles. A profile is a list of parameters that allow MMS
connections via a specific gateway.
To enter and store the profile details
You can only register profile details if you have previously registered profiles in the Connection
manager menu (see "Connection manager", page 101):
1
2
3
4
5
6
7
8
9
10
Press the [Menu/T9] key. Select Messages .
Select Multimedia messages.
Select Settings.
Select MMS profiles.
Choose an empty profile ([...]) and press OK.
Enter the profile name and press OK.
Select Message centre. Select List to select one of the available home page addresses or
the http:// and https:// root address, or type in the URL address. Press OK.
Select Connection profiles. Enter the requested information (the GSM connection and
GPRS connection fields are linked to the Connection manager and thus allow to pick one
from the displayed list - see "Connection manager", page 101). Select Save to store the
data.
Select Gateway settings and type in the IP address.
The sending and receiving of MMS is now possible.
Select Advanced settings and fill in the required fields.
1. All the requested parameters are obtainable from your network operator and/or Wap™ provider.
2. The phone number or access point name, the login and the password are to be stored in the Connection
Manager (see Table , page 101).
3. Access to the content of the MMS profile may depend on the pre-programmation of the settings. The connection settings menu may not be available in some cases. These settings may be 'Locked' (operator dependent) and not be user programmable.
4. Your service provider may require to have the security context reset. Select Yes.
5. For more information on the Advanced settings please refer to "Advanced settings on Wap™ profiles", page 94.
6. The Validity period for an MMS is the maximum time the message is available on the network before it can
be retrieved by the addressee. The validity period is set to Maximum by default. This fearture is present in the
Advanced settings (page 94).
7. When on an existing profile the options Select, View, Delete and Reset security context are available.
Setting multimedia messages characteristics
Before sending a message you can determine whether or not you want to receive a delivery report,
a read reply report (to confirm your message and its contents were read by the addressee), to set
a priority degree (high, normal or low) and a maximum picture size to your message.
1
2
3
4
5
Press the [Menu/T9] key. Select Messages.
Select MMS.
Select Settings.
Select Message config.
Enter the required information and select Save to store your settings.
The availability of this menu and of its contents is operator dependent.
Signature
The MMS application has it own signature independent from the SMS or e-mail ones (please see
"Signature", page 29).
1
2
3
4
5
6
Press the [Menu/T9] key. Select Messages.
Select MMS.
Select Settings.
Select Signature
Select Insert in message and select Text or Name card.
Select Text or Name Card according to your previous choice and enter your signature text
or select the phonecard to be add to the MMS, it can be either My card or any other phonecard.
35- Multimedia Messages
Message auto-retrieval
You may choose whether or not the Multimedia messages should be automatically retrieved
from the network on notification receipt.
The auto-retrieval modes are the following:
On
The Multimedia message is automatically retrieved from the network on notification receipt.
On (with query) The ’retrieve new multimedia message ?’ question is displayed on notification
receipt, thus allowing you to choose whether or not to retrieve the message.
Off
This is the default mode. A notification is received by the phone (it is automatically
stored in the inbox) and an information message or icon is displayed on the standby screen. You can then choose whether or not you wish to retrieve the message
content from the server (select Options/Retrieve message).
To select the retrieval mode:
1
2
3
4
5
Press the [Menu/T9] key. Select Messages.
Select Multimedia messages.
Select Settings.
Select Auto-retrieval.
Choose the required retrieval mode and press OK.
1. The availability of this menu is operator dependent.
2. Even if the Auto-retrieval mode is On, the message are not automatically retrieved if your phone is on
roaming mode or if it cannot attach the network
3. A message can be retrieved automatically (Auto retrieval is On) if the phone is on standby state only.
Sending messages from the outbox
The Outbox folder contains the stored and sent messages (delivered or undelivered). These
messages can be selected from the Outbox menu and can be resent as new MMS messages.
To select one of these messages:
1
2
3
4
Press the [Menu/T9] key. Select Messages.
Select Multimedia messages.
Select Outbox and use [up] or [down] arrow key to scroll to the required message.
Press Options to get to View, Delete, Delete all, Send, Forward, Numbers & addresses
(to store or call the number(s) and/or e-mail address contained in the MMS header) or
Details.
1. You cannot modify the contents of a Multimedia message stored in the Outbox.
2. An ’Attachment’ option is available while viewing the selected message. You can then store the message
attached files
Editing multimedia messages from the drafts folder
The Drafts folder contains the stored unsent messages. These messages can be selected from
the Drafts folder and can be modified and sent.
To select one of these messages:
1
2
3
4
Press the [Menu/T9] key. Select Messages.
Select Multimedia messages.
Select Drafts and use the up or down arrow key to scroll to the required message.
Press Options to Delete, Delete all, Send, Modify, Edit a copy, Preview message, or
Numbers & addresses (to store or call the number(s) and/or e-mail address contained in
the MMS header).
1. Once you have sent one of the Drafts messages it is automatically erased from the Drafts folder.
2. You can use any of the Drafts messages as a template via the ’Edit a copy’ option. The selected message
is not deleted when its copy is sent.
Storage consumption
Please see "Storage consumption", page 32.
36- Multimedia Messages
e-mails
Your phone allows to send and receive e-mails. The e-mails can bear text, images,
sounds, vCard and vCalendar as attached files. The maximum total size for the attached
files is 500 kB. Please read the following instructions to configure your e-mail system and
use the e-mail sub-menu.
You can reach the e-mail menu via two ways:
1
From the standby display select Messages then select e-mail.
The availability of the Message softkey is operator dependent.
or:
1
2
Press the [Menu/T9] key, select
. Messages
Select e-mail.
Reading a received e-mail
To read your e-mails you first need to retrieve them. There are three different ways to retrieve
your e-mails.
From the e-mail main menu:
1
2
3
Press the [Menu/T9] key. Select Messages .
Select e-mail.
Select Retrieve e-mails to get your new messages.
From an empty Inbox:
1
2
3
Press the [Menu/T9] key. Select Messages .
Select e-mail.
Select Inbox, press Retrieve to get your new messages.
From the Inbox when it already contains e-mails:
1
2
3
Press the [Menu/T9] key. Select Messages .
Select e-mail.
Select Inbox to display the e-mails list. Select Options and select Retrieve e-mails to get
your new messages.
The retrieved messages are automatically stored in the Inbox.
1
2
3
OPTION
Press the [Menu/T9] key. Select Messages .
Select e-mail.
Select Inbox to display the e-mails list. Use the arrow keys to scroll up and down and reach
the message you want to read.
Select Options to get to the following options list:
DESCRIPTION
Retrieve e-mails To launch a connection and retrieve all the available e-mails from the
server (according to the free memory space on the phone).
Get current eTo launch a connection and retrieve the selected e-mail from the server
mail
(according to the free memory space on the phone).
View
To view the selected e-mail body.
Reply
To write a reply e-mail and send it to the original e-mail sender.
Reply all
To write a reply e-mail and send it to all the addresses contained in the
original e-mail.
37- e-mails
Delete
Delete all
Forward
Numbers &
addresses
Attachments
Details
4
To delete the current e-mail.
To delete all the e-mails stored in the Inbox.
To transfer the current e-mail to another or several addressee(s).
To view (and eventually store) all the e-mail addresses contained in the
current e-mail.
To view or play (and eventually store) the e-mail attached files.
To view the e-mail details (size, date, etc.).
Select OK or Options/View to read the message.
1. You can also retrieve your e-mails from the network by directly selecting Retrieve (left softkey) from the email sub-menu.
2. You cannot modify the contents of a received e-mail.
3. e-mails bearing an attachment file are shown by the
symbol. The
symbol is displayed when the
file and its attachments were read.
Unread messages are shown by
are shown by
.
and the text is bold. Messages that have already been read
Composing an e-mail
To write an e-mail please follow these steps:
1
2
3
4
Press the [Menu/T9] key. Select Messages .
Select e-mail.
Select Write new.
Highlight the To field. Press OK and select one of the available names from the displayed
list or select New, then type the required e-mail address. Press Valid.
5 Highlight the Subject field. Press OK and type in the e-mail header text (40 characters maximum). Press OK.
6 Highlight the Text field. Press OK and type in the e-mail text (maximum 1530 characters).
Press OK.
7 Highlight the Attached files field if you want to add a melody, a music, an image, a video, a
phone card, a diary event or a speech note to your message. Press OK then select Picture,
Melody, Speech note, phonecard or Other and choose one of the available files. Press
Valid.
7’ If the Attached files field already contains a file: press OK to enter the attached file list.
Then press OK and select New selection to attach a new Picture, Melody, Speech note,
phonecard or Other and choose one of the available files. Press Valid.
8 Highlight the Cc field. Press OK and select one of the available names from the displayed
list or select New, then type the required e-mail address. Press Valid.
1. In the attached field an option menu (available through the OK key) allows to make a New selection, Delete,
Delete all, Details and get an estimated size.
2. You can check the size of the Attachments by selecting OK then Estimated size while in the Attached files
screen.
While writing your e-mail, you can at any time get to the Options menu:
OPTION
DESCRIPTION
Send
Send & store
Store
To send the e-mail.
To send then store the e-mail.
To store the e-mail as a draft.
38- e-mails
Settings
Preparing the phone to send e-mails
You need to enter the connection parameters before you are able to send or receive e-mails
on your phone. Please contact your e-mail service provider for setup detail.
The Profiles list can contain up to 3 e-mail profiles. A profile is a list of parameters that allow
e-mail connections via a specific gateway.
To enter and store the profile details
You can only register profile details if you have previously registered profiles in the Connection
manager menu (see "Connection manager", page 101):
1
2
3
4
5
6
7
8
9
Press the [Menu/T9] key. Select Messages .
Select e-mail.
Select Settings.
Select Profiles.
Choose an empty profile ([...]) and press OK.
Enter the profile name and press OK.
Select Connection profiles. Enter the requested information (the GSM connection and
GPRS connection fields are linked to the Connection manager and thus allow to pick one
from the displayed list - see page 101). Select Save to store the data.
Select Server settings. Enter the requested information (POP3 server, POP3 port number,
SMTP server, SMTP port number, and Let e-mail on server). Select Save to store the data.
Select Account Information. Enter your e-mail address, mailer login and mailer password.
Select Save to store the data.
1.All the requested parameters are obtainable from your e-mail service provider.
2. The phone number or access point name, the login and the password have to be stored in the Connection
Manager (see Table , page 101).
3. A profile name cannot be stored twice. If an error message is displayed please also check the profile
names in the Connection profiles (see Table , page 101).
4. Access to the content of the e-mail profile may depend on the pre-programmation of the settings. The connection settings menu may not be available in some cases. These settings may be 'Locked' (operator dependent) and not be user programmable.
Maximum size
This feature allows to choose the maximum size for the e-mails and attached files received in
the inbox. The maximum size can be modified (from 1kB to 1024kB).
To set a maximum size value:
1
2
3
4
5
Press the [Menu/T9] key. Select Messages.
Select e-mail.
Select Settings.
Select Maximum size.
Type in the maximum e-mail size you wish to retrieve from the server.
The e-mail size is checked before it is downloaded on your phone. If it exceeds the maximum size stored in
the ’Maximum size’ field the e-mail is not downloaded on your phone.
Sending an e-mail from the outbox
The Outbox folder contains the stored and sent e-mails (delivered or undelivered). These e-mails
can be selected from the Outbox menu and can be resent as new e-mails.
To select one of these e-mails:
1
2
3
4
Press the [Menu/T9] key. Select Messages.
Select e-mail.
Select Outbox and use the up or down arrow key to scroll to the required message.
Press Options to View, Delete, Delete all, Send, Edit, Numbers & addresses (to store
the e-mail address contained in the e-mail header) or Details.
You cannot modify the contents of an e-mail stored in the Outbox.
39- e-mails
Editing e-mails from the drafts folder
The Drafts folder contains the stored unsent e-mails. These e-mails can be selected from the
Drafts folder and can be modified and sent.
To select one of these e-mails:
1
2
3
4
Press the [Menu/T9] key. Select Messages.
Select e-mail.
Select Drafts and use up or down arrow key to scroll to the required message.
Press Options to View, Delete, Delete all, Send, Edit, Edit a copy, Numbers &
addresses (to store the e-mail address contained in the e-mail header) and Details.
Once you have sent one of the Draft messages this message is automatically erased from the Drafts folder.
Storage consumption
Please see "Storage consumption", page 32.
40- e-mails
CALLS & TIMES
ccess the Calls & Times menu to check the details of individual incoming and
A
outgoing calls, the duration of the last call, the total call time for all outgoing
and incoming calls or to play the recorded calls.
Call logs
This feature stores details (caller identity,calling time/date and call duration) about the last 20
numbers dialled, calls unanswered and calls received. The calls log can be activated
for Line 1 and Line 2 (Line 1 is your main line. Line 2 availability is subscription dependent).
1
2
3
Press the [Menu/T9] key. Select Calls & Times.
Select Call logs.
Use the [Up] or [Down] arrow keys to scroll through the calls list.
The last number dialled
, received
or unanswered
is displayed at the
top of the list. The caller’s name is displayed if it is registered in one of the Phone
books (if not the phone number is displayed). If your subscription or the caller
subscription does not have Caller Line Identification (CLI) ’Unknown number’ is
displayed. If the caller has withheld his number, ’Withheld number’ is displayed.
Press the [Call] key to call the selected number.
Press Options to access the following menu:
ITEM
ACTION
Call
Store
Delete
Delete all
Edit
Send a
message...
To call the selected number.
To store the number in the Phone book.
To delete the entry.
To delete all entries.
To edit the displayed number.
To send an MMS or SMS message to the selected phone number.
Use the [Up] or [Down] arrow keys to select the required option and follow the instructions displayed.
1. Press the [Call] key from the standby display to access the Call logs list.
2. The Call logs list is automatically emptied after a SIM change on the phone.
Call timers
The voice, Modem and GPRS call information for Line 1 and Line 2 is stored in the Call timers menu.
1
2
3
4
Press the [Menu/T9] key. Select Calls & Times.
Select Call timers.
Select Show.
Use the [Up] or [Down] arrow keys to view all the timer information.
If the Call timers were reset (see "Call timers - reset", page 44) the date of the latest counter reset is displayed.
The call type and the accumulated times of outgoing and incoming calls are displayed.
Selecting Details displays information on calls made on your home network, on
National roaming and on International roaming.
1. For GPRS timers, selecting Details displays information about connections according to
the Connection manager profiles.
2. If Line 2 is active too, 'All Calls' for Line 1 and Line 2 are displayed separately.
41- Calls & Times
Balance information (subscription dependent)
This service may be supplied by your service provider. It allows you to view the remaining airtime balance on your phone line.
Please contact your service provider for more information. If your subscription allows access to
this information:
1
2
3
4
Press the [Menu/T9] key. Select Calls & Times.
Select Call timers.
Select Balance information.
Select Call or Set number.
When selecting Call, if the balance information number is already stored, a call is sent to the
balance information centre. If no number is stored, select Set number and enter it. Press OK
to store the number, then select Call to call the information centre number.
Reminder - call duration
You can set a duration reminder to beep regularly to remind you of the time spent on your call.
The frequency can be any multiple of 1 minute (up to 59 minutes) and a beep is emitted 10 seconds before you reach the set limit..
1
2
3
4
5
6
Press the [Menu/T9] key. Select Calls & Times.
Select Call timers.
Select Reminder.
Select On to activate the Reminder.
Enter the reminder interval.
Press OK to validate the entry.
Call timers - reset
This feature allows you to reset the call timers. The 4 digit lock code is required to reset the call
timers (default lock code: '0000').
1
2
3
4
5
Press the [Menu/T9] key. Select Calls & Times.
Select Call timers.
Select Reset.
Select Yes.
Enter the phone lock code and press OK.
Call costs - management
Some service providers offer an Advice of Charge (AoC) subscription service allowing you to
view the latest call cost, the total calls cost and the remaining balance on your account (once
a 'credit limit' has been set ).
To display these, you must first set a currency value and enter an average cost per unit (only
calls units are displayed if the cost information is not stored).
To set a currency value per Unit:
1
2
3
4
5
6
7
Press the [Menu/T9] key. Select Calls & Times.
Select Call costs.
Select Display cost type.
Select Currency. The current currency unit value is displayed.
Select Modify. Enter your PIN 2 code and press OK.
Enter the currency name (up to 3 letters). Press OK to validate.
Enter the unit cost (e.g.: 0.15 Euro per minute). Press OK to validate.
To set the call cost type to Units:
1
2
3
4
Press the [Menu/T9] key. Select Calls & Times.
Select Call costs.
Select Display cost type.
Select Units.
When the cost type is set to Units, the credit limit and the remaining credit are shown in units.
42- Calls & Times
Setting the credit limit (subscription dependent)
You may also be able to set a credit limit to your calls. Once the credit limit has been reached, no more
chargeable outgoing or incoming calls are allowed. You can however still make emergency calls.
The PIN2 code is required to set the credit limit.
1
2
3
4
5
Press the [Menu/T9] key. Select Calls & Times.
Select Call costs.
Select Credit limit. The display indicates the current credit limit set.
Select Edit. Enter your PIN 2 code and press OK.
Enter the credit limit (use
to enter a decimal point for currencies). Press OK to validate.
When a credit limit has been set, the selection from the 'Credit limit' display is Edit or Set no limit.
Show costs
1
2
3
4
Press the [Menu/T9] key. Select Calls & Times.
Select Call costs.
Select Show.
Use [Up] and [Down] arrow keys to display the Last Call and All Calls and show the
Remaining credits.
The remaining credit is shown in either units or currency, as set by Cost Type menu above.
Call costs - resetting all costs to zero
To reset all call costs to zero:
1
2
3
4
5
Press the [Menu/T9] key. Select Calls & Times.
Select Call costs.
Select Reset.
Select Yes.
Enter the PIN 2 number and press OK.
Recorded call
This sub-menu allows you to play the recorded phone calls. If several phone conversations
have been recorded, they are played one after another.
1
2
Press the [Menu/T9] key. Select Calls & Times.
Select Recorded call.
In compliance with European regulations, you are obliged to inform your correspondent before
recording a phone conversation.
Line selection
Some operators support the use of a second line. You may then have two mobile phone numbers
(e.g. a business line plus a personal line). To use them you need to select the line to be used.
1
2
3
Press the [Menu/T9] key. Select Calls & Times.
Select Line selection.
The current line selection is displayed.
Use the [Up] and [Down] arrow keys to scroll to the required line. Press OK to validate.
1.The Line selection sub-menu may not be available on your phone. Please contact your service provider for
further details about this service.
2. Line 1 and Line 2 can be named (Office and Home for instance). Refer to My number menu (see "My number(s) display", page 52). Whichever line is selected to send calls, incoming calls can still be received on
either line.
43- Calls & Times
PHONE BOOK
hone numbers can be stored in the phone memory and in the SIM card
memory.
- The phone memory can store up to 500 'extended' cards (called 'Phone book
cards'). These cards allow you to store different information types: family name,
first name, home number, phone number, work number, fax number, two mail
addresses, postal address, business information, voice tag, group name, card
related melody and an associated icon, picture or video.
- The SIM card memory capacity may vary according to your operator or service
provider. The SIM memory allows you to store one name, one phone number and one voice
tag per card.
Both the SIM and the phone memories are searched when reading the Phone book contents, unless you have previously selected a folder to be scanned when accessing the Phone book (please
see "Sorting the Phone book entries so that they can be viewed as separate folders", page 48).
P
Press the [Phone book] key or the left arrow to directly access the Phone book from the standby display.
Storing names and telephone numbers
Names and numbers can be stored directly in the Phone book or copied from different sources
such as SMS messages, last dialled number list, etc.
There are several ways to store numbers in the Phone books:
Phone names card
From the standby display:
1
2
3
4
Enter the number. Select Store.
Select New phone name.
The Home number, Mobile number, work number, or FAX number list is
displayed, thereby allowing you to select a number type.
Enter the card requested data and select Save to store the information.
Via the menu:
1
2
3
4
Press the [Menu/T9] key. Select Phone book..
Select Add name.
Select Phone name.
Enter the card requested data and select Save to store the information.
The Groups field allows you to identify the caller’s type according to entries you have previously set (see "Creating
a group of cards ", page 49).
SIM names card
From the standby display:
1
2
3
4
Enter the number. Select Store.
Select New SIM name.
Fill in the available fields and select OK to validate your entries.
Select Save to store the card.
44- Phonebook
Via the menu:
1
2
3
4
5
6
Press the [Menu/T9] key. Select Phone book.
Select Add name.
Select New SIM names.
Enter the name and select OK.
Enter the number and select OK.
Select Save to store the card.
Storing a received number
Numbers stored in the last dialled, received, unanswered call information and SMS message
locations can also be stored in the Phone book:
1
2
With a last dialled call, received call, unanswered call or SMS message select Options.
For an SMS message, select Numbers if the number is contained in an SMS. The message
number(s) is/are displayed. Select one if several numbers are available.
2’ For received and unanswered calls, select Store.
3 Follow the above mentioned procedure to create a phone name or a SIM name card then
select Save to store the card.
1. While entering a number, pressing the [Clear] key once deletes the last character. Holding the [Clear] key
deletes the whole number.
2. You can use _ (wild card spaces) to store numbers (wild card spaces cannot be obtained when registering
a number from the standby display).
When calling a number containing wild card spaces, select the number from the Phone book, select Options or
press on the [Call/Send] key and enter the number corresponding to the wild card spaces (=missing figures).
3. The *, +, p (pause) and _ characters- which are accessible by pressing and holding the
key when registering a number - can be stored as part of numbers.
4. If the SIM card or phone memory are full, a warning message is displayed on the Phone book selection.
Copying names and numbers
When consulting your Phone book you can copy any SIM or phone card to another directory.
1
2
3
Press on the left arrow key or press the Phone book key or press the [Menu/T9] key then
select Phone book.
Select Read. Scroll to one of the items from the displayed list. Select Options.
Select Copy, then select one of the available destination directories (Phone names, SIM
names, SIM fixed, My card). The card content is then automatically copied to the required
location.
Copying all names and numbers
When consulting your Phone book for the first time the ’Copy all SIM names to phone?’
message is displayed. Select Yes.
You can also, at any time, copy all the names cards from the Phone to the SIM card or vice
versa.
1
2
3
4
5
Press the [Menu/T9] key. Select Phone book.
Select Read.
Select Options.
Select Copy all.
Select Phone to SIM or SIM to phone.
All the names are copied unless the SIM card memory does not bear enough free space when
copying the Phone entries to the SIM card. A warning message is then displayed.
1. If your Phone book cards bear more than one number (home, mobile, work, fax numbers), the first available
number from the list is copied to the corresponding SIM card entry.
2. If the Phone book entries are sorted (please see "Sorting the Phone book entries so that they can be
viewed as separate folders", page 50), the Copy all option allows to copy the SIM names in the phone memory
or to copy the Phone names in the SIM memory.
45- Phonebook
Moving names and numbers
When consulting your Phone book you can move any SIM or phone card to another directory.
1
2
3
Press on the [Left] arrow key or press the [Phone book] key or press the [Menu/T9] key then
select Phone book.
Select Read. Scroll to one of the items from the displayed list. Select Options.
Select Move, then select one of the available destination directories (Phone names, SIM
names, SIM fixed, My card). The card content is then automatically moved to the required
location.
Adding a picture or an icon to your Phone book card
You can add a picture to each of your Phone book cards. This picture can be an icon, an image
or a picture you captured
1
2
3
4
Press the [Menu/T9] key. Select Phone book.
Select Add name.
Scroll down and select Picture. Press OK to display the Picture folder content.
Select the required icon or select
to display the pictures list, then select the required picture.
The
icon leads to the Pictures list. You can therefore select
one of the registered images (please see "Pictures", page 69)
and link it with your phone card
The icons list allows you to store your card with a symbol or an
image that is then displayed together with the caller’s name on
incoming or outgoing calls.
5
Select Save to store your settings.
1. You can link about 100 images with your Phone book cards. If the images folder is full (images too big), an
error message will be displayed.
2. The images remain attached to the Phone book cards even if you have deleted them from the Pictures
folder memory. You can modify or delete them one after the other via the Phone book cards (see "Editing a
Phone book or a SIM name card", page 47).
3. When sending a Phone book card via the infrared port, the image is automatically sent unless the file is protected.
4. The Image failure icon is displayed on incoming or outgoing calls if a problem related to the image has been
detected by the phone.
46- Phonebook
Setting a melody, a music or a speech note as a ringtone
You can set a melody, a music or a speech notes as a ringtone for each of your Phone book
cards. If you set a video as a ringtone the audio track of the video sequence only is played. This
ringtone is played on on receipt of an an incoming call.
1
2
2
3
4
5
6
Press the [Menu/T9] key. Select Phone book.
Select Add name.
Select New phone name.
Scroll Down and select Ringtone. Press OK.
Select Melodies (to set a melody as a ringtone), Speech notes (to set a speech note as a
ringtone) or No sound (to deactivate the ringtone). Press OK to confirm your selection.
Select the required melody or the required speech note. Press OK to confirm your selection.
Select Save to store your settings.
If no melody is set as a ringtone for your Phone book card, the default ringtone or the melody you set as a
ringtone (please see "Ringtone selection", page 94)is played on receipt of an an incoming call.
Editing a Phone book or a SIM name card
From the standby display:
1
2
3
Press the [left] arrow or the [Phone book] key to access the Phone book.
Scroll down to the card you want to access and select OK.
Scroll down to the field(s) you want to modify and amend it/them. Select Save to store the
changes.
Via the menu:
1
2
3
4
5
6
Press the [Menu/T9] key. Select Phone book.
Select Read.
Select one of the stored cards.
Select Options.
Select View.
Scroll down to the field(s) you want to modify and amend it/them. Select Save to store the changes.
You can create a voice dialling pattern on Phone book cards. This voice dialling pattern can
only be recorded in edition mode.
A quick access to the SIM names is available from the idle screen by entering the position of the card entry in
the SIM followed by .
Eg: if you want to call Betty (2d name in you SIM card) just press
and
from the idle screen.
Recording a Voice dialling pattern:
1
2
3
Press the [Left] arrow key (from the standby display) or press the [Phone book] key to access
the Phone book.
Scroll down to the card you want to access and select OK or select Options then select View.
Scroll down to the Voice dialling field and select OK. Select New to record the voice pattern or
select Options then Record if a voice pattern is already recorded and you want to change it.
Repeat the name until it is stored (minimum = twice). Pronounce it as clearly as possible and
in a quiet environment. When the voice patterns match, Stored is displayed.
You may have to select the number - the voice dialling pattern has to be attached if several numbers are
stored on the card. Select Home number, Mobile number or Work number if you have registered several numbers on a Phone book card.
47- Phonebook
Viewing and calling Phone book numbers
There are two ways of viewing and calling entries stored in the Phone book:
Directly from the standby display:
1
2
3
Press the [Left] arrow key or the [Phone book] key to display the Phone book list.
To access the required name, either scroll up or down or press a numeric key to access the
different letters associated with the key (e.g: press
twice to reach the names starting with
letter ’B’) or type in the required name in the edition area displayed at the top of the screen
(you can enter up to 20 characters).
Press the [Call] key or select Options then select Call.
When typing in the required name in the edition area, the Multitap mode is only available.
Via the menu:
1
2
3
Press the [Menu/T9] key. Select Phone book.
Select Read to display the Phone book list, then scroll up and down to the required name or
press a numeric key to access the different letters associated with the key. E.g: press
twice
to access the names starting with letter 'B'.
Press the [Call] key or select Options then select Call.
The list of Phone book entries is displayed in alphabetical order.
1. Selecting a group from the Folder selection displays the names/phone numbers of the corresponding
group. This group is then displayed when next reading the Phone book contents.
2. Selecting Options displays the following menu choice: View, Call, Add name, Delete, Delete all (Phone
names or SIM names), Copy, Copy all, Move, Group folder selection (to select All names, the Phone names
only, the SIM names only or the groups members), Send by... e-mail, MMS, SMS or Infrared port, Send a
message...(e_mail, MMS or SMS). Some of these options may not be available according to the selected
folder.
3. If several phone numbers are stored on a Phone name card, scroll down to the required number and select
it before activating the call.
Sorting the Phone book entries so that they can be viewed as separate folders
You can split the Phone book entries into folders and view either the Phone names, the SIM
names or a selected group of entries when reaching the Phone book list.
1
2
3
4
Press the [Menu/T9] key. Select Phone book.
Select Read.
Select Options
Select Folder selection, then choose All names (to display all the folders contents), Phone
names (to display the phone cards only), SIM names (to display the SIM cards only) or one
of the Groups names (see "Creating a group of cards", page 51) if any.
The selected folder remains active for further Phone book reading. Please go over the above procedure to
select another folder or display the full Phone book list.
Voice dialling
You can make a call by using your voice.
To create a voice pattern:
1
2
3
4
5
Press the [Menu/T9] key. Select Phone book.
Select Voice dialling.
Select New entry. All name entries are displayed.
Use the [Up] and [Down] arrow keys to select the card you want to use and press OK.
If several phone numbers are registered on a card (e.g. Home number, Mobile number or
Work number) select one by pressing OK.
You are then prompted to pronounce the name at least twice (pronounce it as clearly as possible).Stored is displayed when both voice patterns match.
If the voice patterns do not match, Failed is displayed. Repeat the whole voice registration procedure again.
To view the voice dialling numbers list:
1
2
3
4
Press the [Menu/T9] key. Select Phone book.
Select Voice dialling.
Select List.
Use the [Up] and [Down] arrow keys to view the requested entry.
48- Phonebook
5
Press Options to play the voice pattern, select Play Back, to remove voice tag from the
voice dialling list, select Erase, or to create a new voice pattern select Record.
To remove all phone numbers from the voice dialling list:
1
2
3
Press the [Menu/T9] key. Select Phone book.
Select Voice dialling.
Select Delete all.
To call a phone number using a voice pattern:
1
2
3
From the standby display, press and hold the call key.
Pronounce the name as clearly as possible.
The name called as well as an animated icon
ceeds as normal.
are then displayed and the call pro-
Free space in the Phone book
To view the remaining capacity in the Phone book:
1
2
Press the [Menu/T9] key. Select Phone book.
Select Storage used to get to the Phone names Storage used; press the [Down] arrow key
to get to the SIM card Storage used.
If available, the free memories in the FDN list are also displayed. Please see "Fixed dialling numbers", page
50 for more information on FDN numbers.
Creating a group of cards
Groups of cards can be defined for the Phone book. This feature allows you to group certain cards
and to play a specific melody on receiving an incoming call from one of the group members.
To create a group:
1
2
3
Press the [Menu/T9] key. Select Phone book.
Select Groups.
Select any blank template [...] and select OK. The following items are displayed:
ITEM
FUNCTION
Group name
Ringtone
To enter and store a group name.
To select a melody to be used as a ringtone on group member calls.
4
5
Enter or select the requested data. Press OK to validate.
Press Save to store the defined group.
Groups’ characteristics can be modified or deleted (when in the Groups menu, select OK to
amend the settings or select Delete to erase the group).
To modify a group:
1
2
3
4
Press the [Menu/T9] key. Select Phone book.
Select Groups.
Select the group to be modified and select OK then select the group name and/or the ringtone. Select the new parameters (name/melody).
Select Save to store your settings.
To select a group when storing a number:
1
2
3
4
Repeat the Phone names storage procedure (see "Storing names and telephone numbers",
page 46) and fill in the Phone names card.
Scroll down to Groups and select OK.
Select one of the displayed groups from the list.
Select Save to store your settings.
Groups can only be set for the Phone names cards (not for the SIM names cards).
To view group members:
1
2
3
Press the [Menu/T9] key. Select Phone book.
Select Groups.
Select the required group name and select Options.
49- Phonebook
4
Select Members. The group members list is displayed. Please use the same procedure as
when in the phone book to reach the required name.
My card
My card is a specific storage location where you can enter personal data. You can easily access
My card and send its contents to another device via the infrared port or SMS.
My card contents is identical to the phone cards contents except for the Groups and Voice dialling
fields.
To enter My card data set:
1
2
3
4
Press the [Menu/T9] key. Select Phone book.
Select My card.
Select View and enter the requested information as for a Phone book card (validate each
entry by selecting OK).
Select Save to store your card.
To send My card via the Infrared port or by SMS or e-mail:
1
2
3
Press the [Menu/T9] key. Select Phonebook
Select My card.
Select Send by... then select Infrared port: the infrared port automatically opens and sends
the card. Or select SMS, then enter the mobile number to send the card to or select it via
Options then Names list and press OK. Or select e-mail and enter the e-mail address in the
To field.
My number(s) display
The phone can display your main line (Line 1) mobile number, Line 2(Alternate Line Service)
mobile number and your data/fax numbers (these are SIM card dependent). These numbers may
be stored in the SIM card. You can also choose to enter them manually.
To view, name and edit your own number(s),
1
2
Press the [Menu/T9] key. Select Phone book.
Select My numbers. The mobile number for Line 1 is displayed if it is stored in the SIM card.
If not, select Edit and enter your number and your name (select OK to save the entered
information). You can access an Options list to help you store the required information.
ITEM
FUNCTION
Codes
To select one of the pre-stored international country codes from the list. The
selected code is then inserted at the beginning of your number.
To copy the full number in order to paste it in another edition screen.
To paste a copied number.
To delete all the typed characters from the current edition window.
Copy all
Paste
Clear all
3
Scroll down to view or enter Line 2, your data and fax numbers.
1. Line 2, data and fax numbers can only be accessed if your SIM card has these subscriptions.
2. My numbers availability depends on your service provider.
Fixed dialling numbers
Fixed dialling is a feature that restricts outgoing calls to 'fixed' numbers or 'prefixes' contained in
SIM cards that support this feature. When the Fixed Dialling Numbers (FDN) feature is activated,
dialling numbers, diverting calls and sending SMS to numbers not registered in the FDN list is
forbidden. The number of FDN entries to be stored depends on the SIM card capacity. Activating
the FDN feature or registering numbers in the FDN list is PIN 2 protected (contact your service
provider to get the PIN 2 number).
The following menu (Fixed dialling) and operations are only available on your phone if your SIM
card allows fixed dialling.
50- Phonebook
To activate or deactivate FDN operation:
1
2
3
4
Press the [Menu/T9] key. Select Phone book.
Select Fixed dialling. Select Status.
Select On or Off. Enter the PIN2 number.
Select OK to validate.
The Fixed dialling sub-menu may not be available on your phone. Please contact your service provider for further
details.
To view the numbers stored in the FDN list:
1
2
3
Press the [Menu/T9] key. Select Phone book.
Select Fixed Dialling.
Select View to view the FDN list entries. Pressing Options allows you to view, call, add a
name, delete, copy or move numbers to the phone or SIM card memory, but also to send
these numbers by Infrared port or SMS, or send a message (an SMS, a Mail or an MMS).
To add a new number to the FDN list:
1
2
3
4
5
Press the [Menu/T9] key. Select Phone book.
Select Fixed dialling.
Select Add new.
Enter your PIN2 code and press OK;
Fill in the displayed fields as in any SIM name card then select Save to store your settings.
1. Wild card spaces can be used with the numbers stored in the FDN list. E.g. number +441707 278_ _ 9
allows calls to all numbers from 278009 to 278999 to be dialled. The number can be edited and dialled from
the standby display.
2. You may be asked to enter your PIN2 code.
Export
The purpose of the Export feature is to allow you to send the Phone book contents to another
device (e.g. a pc) via the infrared port or by SMS.
1
2
Press the [Menu/T9] key. Select Phone book.
Select Export..., then select Yes. The entire contents of the Phone book are exported and
grouped together in a Vcard file and stored in Fun & Media box/Others.
When exporting a Vcard file you can directly send it via the infrared port or by SMS.
51- Phonebook
CAMERA
he camera application allows you to take pictures from your mobile internal
or external screens.
These pictures can then be used to:
- personalise your standby display on your Main screen and your External screen,
your Welcome or your Goodbye screen (please see "Setting a still or animated image as a standby display (for the Main screen or the External screen), as a Welcome screen or as a Goodbye screen from the Pictures folder", page 71),
- be sent to other devices (mobile phones, PC) by Mail (), MMS or via the miniSD™ Card or via the infrared port (see "Infrared port", page 19),
- personalise your phone cards (see "Phone names card", page 44).
You can choose from 6 picture size types: 2M pixels (1224x1632 pixels), Large (960x1280 pixels), normal (480x640 pixels), Wall paper (240x320 pixels), Portrait (240x240 pixels), or Messaging (120x160 pixels).
The use of the camera and the sending, forwarding and reproduction of the pictures taken are
subject to property and privacy rights. Do not take a picture unless authorised.
The camera feature can be accessed in two ways: with closed clamshell or with open clamshell.
T
The Camera screen and the related icons
The table shows the information related to the camera application and its state while it is in use.
The screen shot below is a preview example; the Camera related icons described in the table
below are the ones which can be displayed while using the Camera features. The features described
in this table are further explained in the chapter.
Camera related icons
Upper part:
Camera application activated.
Picture resolution (size): Messaging (120x160 pixels), Portrait
(240x240 pixels), Wall paper (240x320 pixels), Normal
(480x640 pixels), Large (960x1280 pixels) and 2M pixels
(1224x1632 pixels).
Compact light activated.
Self timer activated.
Image quality modes: Super fine, Fine, Economic.
Modes: Night, Sport, Scenery, Sensitive, Backlight,
Monochrome, Sepia and Negative.
Brightness activated.
Contrast activated.
White balance: Indoor fluo, Indoor lamp, Outdoor
Sharpness: Sharp, Soft
Zoom (= zoom levels)
Lower part:
Image quality modes: Super fine, Fine, Economic.
Modes: Full auto (standard mode), Night, Sport, Scenery,
Sensitive, Backlight, Monochrome, Sepia and Negative.
Sharp Soft
Brightness gauge (= to set the brightness level)
Contrast gauge (= to set the contrast level)
White balance: Normal, Indoor fluo, Indoor lamp, Outdoor
Sharpness: Normal, Sharp, Soft
Zoom (= zoom levels)
52- Camera
How to hold your mobile
Subject behind the phone
To take a picture
1
Open the lens cover (see the drawings above).
or
1’ Press the [Camera/Video]
side key, then open the lens cover.
2 Choose a subject.
3 Press the [Camera/Video]
side key to take your picture.
The shutter sound is played and the red light blinks.
1. You cannot take a picture while a voice communication is in progress.
2. The Shutter sound is a ’Camera-like’ sound that is heard when a picture is captured.
3. You may not be able to deactivate nor mute the shutter sound option on your phone.
4. Do not forget to close the lens cover after taking a photo otherwise it covers the loud speaker.
Storing/erasing your picture
After a picture has been taken (see " To take a picture" on page 54), a phone assigned file name
and a message "Keep this photo?" will be displayed.
1
Select Clear to erase it or press OK to store the picture.
The picture is stored in the Pictures folder of the Fun & Media box menu (see "Pictures", page 69)
except if you have previously chosen to have it stored on the miniSD™ Card (please see "miniSD™ Card", page 84). The picture file is stored as a .jpg file.
Adjusting the preview
You can adjust several setting types before taking a picture. These settings can be accessed
from an items menu on the preview screen by pressing the [Menu] side key.
To switch to the video application
This item allows you to switch from the camera application to the video application to record a video.
1
2
Press the [Menu]
side key. Select Video recorder.
Press the [Camera/Video]
side key to confirm your selection.
To select the image size
1
2
3
Press the [Menu]
side key. Select Resolution.
Select the 2M pixels, the Large, the Normal, the Wall paper, the Portrait
or the Messaging mode.
Press the [Camera/Video]
side key to confirm your selection.
1. The Wall paper allows you to set your picture as a standby display for your Main or External screen or as a
Welcome or a Goodbye screen.
2. If you wish to send your image by Mail or MMS, we advise you choose the Messaging mode.
54- Camera
To select the image quality
This setting allows you to choose a quality level for your picture. The better the quality (sharpness
of the displayed image), the bigger the file size. If you wish to send your image by Mail or by
MMS, we advise you choose the Economic mode.
1
2
3
Press the [Menu]
side key. Select Quality.
Select the Super fine, the Fine or the Economic mode.
Press the [Camera/Video]
side key to confirm your selection.
To select the brightness
1
2
3
Press the [Menu] side key. Select Brightness.
Select one of the seven brightness levels.
Press the [Camera/Video]
side key to confirm your selection.
To select the contrast level
1
2
3
Press the [Menu] side key. Select Contrast.
Select one of the seven contrast levels.
Press the [Camera/Video]
side key to confirm your selection.
To set the image sharpness
1
2
3
Press the [Menu] side key. Select Sharpness.
Select Normal, Soft or Sharp.
Press the [Camera/Video]
side key to confirm your selection.
To select the zoom setting
1
2
3
Press the [Up]
or [Down]
side key. Select Zoom.
Select one of the zoom levels by scrolling left ( ) or right ( ).
Press the [Camera/Video]
side key to confirm your selection.
The available zoom levels depend on the selected picture resolution.
To access the mode setting
This setting allows you to choose the colour and exposure mode before taking the picture in
order to optimise the picture quality.
1
2
3
Press the [Menu]
side key. Select Mode.
Select the Full auto, the Night (dark context), the Sport (moving subject),
the Scenery (to capture a landscape picture), the Sensitive (automatic light
setting), the Backlight (to avoid any backlighting), the Monochrome (to
take a black & white picture), the Sepia (to thave a retro effect) or the Negative (to have a colour reverse effect) mode.
Press the [Camera/Video]
side key to confirm your selection.
To set the white balance
1
2
3
Press the [Menu] side key. Select White balance.
Select Auto, Outdoor, Indoor lamp or Indoor fluo.
Press the [Camera/Video]
side key to confirm your selection.
To select the storage memory space
Before taking a picture you have to choose where the image will be stored in. The default picture
storage space will be in the "Phone memory".
1
2
3
Press the [Menu]
side key. Select Storage.
Select Phone memory or Memory card.
Press the [Camera/Video]
side key to confirm your selection.
55- Camera
To access the compact light setting
This feature sets up a light which lights up your subject during the picture taking.
1
2
3
Press the [Menu]
side key. Select Compact light.
Select On or Off.
Press the [Camera/Video]
side key to confirm your selection.
To access the self timer
The self timer offers the possibility of taking a delayed picture, thereby enabling you to be in the
picture.
1
2
3
Press the [Menu]
side key. Select Self timer.
Select On.
Press the [Camera/Video]
side key to launch the countdown.
The 10 seconds countdown is displayed on the external screen. The capture is automatically performed when the countdown is over.
If an event occurs (Mail, MMS reception...) or the mobile's behaviour is modified (any key
pressed, clamshell opened or closed...) after the countdown has started, the self timer is automatically stopped and set to Off. Once the event has been processed, the mobile returns to the
preview screen.
To display/conceal information icons
This option allows you to activate or conceal the mobile information status icons display on top
of the screen (see "Camera related icons", page 54)
1
2
3
Press the [Menu]
side key. Select Info.
Select On (the icons are displayed) or Off (the icons are not displayed).
Press the [Camera/Video]
side key to confirm your selection.
Macro switch setting
The macro switch allows you to set the focus of the camera in order to
take a picture of very close items. You can for instance use this feature
to clearly capture text. Move the macro switch cursor right or left according to the required effect.
You can adjust these settings via the open clamshell (please see "Adjusting your picture", page 60). When the
clamshell is closed, the settings are kept.
How to view your pictures
You can view the pictures stored on your mobile or on the miniSD™ Card (see "Pictures", page
71) on the external screen. However, to get an optimised display of the pictures, it is advisable
to view them on the internal screen.
1
2
3
4
Open the clamshell.
From the standby display, press the [Menu/T9] key. Select Fun & Media box.
Select Pictures, then select the required picture.
Press OK to view the picture.
56- Camera
Open clamshell: self-portraits
The camera feature, with open clamshell, is to be used with the keypad only. This way of doing
is to be used to take pictures of oneself and to view the stored pictures in an optimised way.
For picture-taking with open clamshell, here are the keys to be used:
[Up] side key
Camera & Video lens
Navigation key
[Down] side key
[Ok] key
Available shortcuts
Each of the camera-related keys has several functions. While using the camera feature, please
use the keypad as follows:
KEYS
DESCRIPTION
[Up] side key
[Down] side key
[OK] key
[Up] navigation key
[Down] navigation key
[Left] navigation key
[Right] navigation key
To access the Zoom panel.
To access the Zoom panel.
To capture your image.
To access the Zoom panel and to scroll to the next one.
To access the Quality panel and to scroll to the next one.
To access the Brightness panel.
To access the Mode panel.
The settings described above are to be accessed via the Preview mode only.
How to hold your mobile
Subject in front of the
mobile (for self-portrait)
57- Camera
To access the camera application
You can access the camera application via two routes:
1
From the standby display, press the [OK] key.
1
2
From the standby display, press the [Menu/T9] key. Select Camera/Video.
Select Capture a photo.
or:
The infrared port automatically closes when the camera application is accessed.
To take self-portraits
These pictures can be stored either on your mobile or on a miniSD™ Card (please see "miniSD™ Card", page 86)
To take self-portraits the mobile displays mirrored images on the main screen.
1
2
3
Place yourself in front of the mobile so that your image is displayed on the main screen.
Adjust the required settings (see "Adjusting your picture", page 58).
Press OK to capture your picture.
1. When a picture is taken the shutter sound is played and the red light flashes.
2. You may not be able to deactivate nor mute the shutter sound option on your mobile.
3. The Shutter sound is a ’Camera-like’ sound that is heard when a picture is captured.
4. You cannot take a picture while a communication is in progress.
Storing/erasing your picture
When a picture has just been taken (see "To take self-portraits", page 58), the file name and
the «Keep this photo?» message is displayed.
1
Select OK to store the picture or select Clear to erase it.
The picture is stored in the Pictures folder of the Fun & Media box menu (see "Pictures", page 71)
except if you have previously chosen to have it stored on the miniSD™ Card (please see below).
The picture file is stored as a .jpeg file.
An Options list is available:
OPTIONS
DESCRIPTION
Camera
Full screen
Set as...
To get back to the camera preview screen.
To view your image in full screen.
To set your picture as a standby display for your Main screen, External
screen, as a Welcome screen or as a Goodbye screen.
To send the picture by e-mail, by MMS or via the infrared port.
To delete the current picture.
To rename the current picture.
To display information about the file Name, the Title, the Author (the device
name), the Resolution (width x height in pixels), the Size, the Storage date,
the File protection status, the Copyright of the picture. The empty fields are
not displayed.
Send by...
Delete
Rename
Details
Adjusting your picture
Before taking a picture you can access the following Options list in order to set your Preview
details.
OPTIONS
DESCRIPTION
Video recorder To switch from the Camera application to the Video application.
Settings
To access a settings list (see the table below).
Frames
To set or remove a frame over the preview area (to set a frame on your
internal or external preview, please see "Adding a frame to your picture",
page 81).
Compact light To turn the Compact light On/Off.
Self timer
For automatic picture taking after a 10 seconds countdown. See "To access
the self timer", page 58.
58- Camera
You can adjust the camera settings before taking your picture.
1
2
From the preview screen, select Options.
Select Settings:
ITEMS
DESCRIPTION
Resolution
To select the picture size. Select the 2M pixels, the Large, the Normal or the
Wall paper, the Portrait or the Messaging mode.
Quality
To select the image quality. Select the Super fine, the Fine or the Economic
mode.
Shutter sound To select the shutter sound volume level.
Compact light To select the intensity level of the compact white light. Select the High, the
Medium or the Low mode.
Info
To display/conceal the information icons on top of the dispaly.
Storage
To select either the phone memory or the memory card to store your picture.
3
4
Fill in the available entries and select OK to validate your entries.
Select Save to store the changes.
You cannot deactivate or mute the shutter sound Option on your phone.
How to view your picture
You can view the pictures that have just been taken or stored on your phone or on the miniSD™ Card (see "Pictures", page 69) on the internal screen.
To view the pictures that are stored in the Fun & Media box picture folder:
1
2
3
4
Open the clamshell.
From the standby display, press the [Menu/T9] key. Select Fun & Media box.
Select Pictures, then select the required picture.
Press OK.
To access the camera application from another application
The Camera application can be activated from the Options menu whilst using other applications
on the phone. In this case, the available resolution types vary according to the application. The
camera-accessible applications are the following:
APPLICATIONS
AVAILABLE RESOLUTION
Phonebook
Settings (standby
screen for Main or
External screen
welcome or
goodbye screen)
Mail, MMS
Portrait and Messaging.
Portrait, Wall paper and Messaging.
All (If you wish to send an image by Mail or MMS, the image may be
automatically resized).
To access the camera application from the Phonebook:
1
2
3
4
5
Press the [Menu/T9] side key. Select Phonebook.
Select Add name, then New phone names.
Scroll down and select Picture.
From the picture browser, select Options.
Select Camera.
To access the camera application from the Settings menu:
1
2
3
4
5
Press the [Menu/T9] side key. Select Settings.
Select Display then Standby screen. .
Select Main screen, External screen, Welcome screen or Goodbye screen. Scroll down
to My Picture.
From the picture browser, select Options.
Select Camera.
59- Camera
To access the camera application from the Message menu:
1
2
Press the [Menu/T9] side key. Select Messages.
Select MMS, Select Write new. Scroll down to the Content field, press OK and scroll to the
Pictures field. Press OK and select Picture.
2’ Or select e-mail, Select Write new. Scroll down to the Attached files field, press OK and
select Picture.
3 From the pictures browser, select Options.
4 Select Camera.
If a call is in progress, access to the camera is not possible.
60- Camera
VIDEO
This application allows you to record and play videos up to 5 MB (about 10 minutes time) on your phone internal or external screens. These videos can bear
sound. They can be recorded as several sequences (on a single file) via the
Pause mode.
You can send those videos to other devices (mobile phones, PC) by Mail, MMS,
or via the infrared port, you can even attach videos to your phone cards (see
"Storing names and telephone numbers", page 46). Two video size types are
available: Normal (QCIF format: 176x144 pixels) and Small (sub-QCIF: 128x96
pixels).
The videos can be stored on your phone or on a miniSD™ Card (see "To select the storage
memory", page 67). The file extension type supported by the video application is .3gp.
The use of the video recorder and the sending, forwarding and reproducing of the videos are
subject to property and privacy rights. Do not make videos unless authorized.
The video feature can be accessed when clamshell is either closed or open.
Video display
The table shows the information related to the Video application and its state while it is in use.
The screen shot below is a preview example; the Video related icons described in the table below are the ones which can be displayed while using the Video features. The features described
in this table are further explained in the chapter.
Video recorder icons
ICONS
EXPLANATION
Upper part:
Video application activated.
Video resolution (size): Normal (QCIF format: 176x144) and
Small (sub-QCIF format: 128x96).
Video quality modes: Super fine, Fine, Economic.
Brightness activated
Zoom (= zoom levels)
Compact light On
Self timer On
Microphone On
Microphone Off
Lower part:
Image quality modes: Super fine, Fine, Economic.
Brightness gauge (= to set the brightness level)
Zoom (= zoom levels)
Record symbol: press on the [OK] key or on the [Camera/
Video] side key to launch the recording.
Pause symbol: press on the [OK] key or on the [Camera/
Video] side key to pause the recording.
Stop symbol: press on the Right softkey or on the [Menu] side
key to stop the recording.
When in recording mode, the gauge fills in with red colour to
indicate the recording progress.
Duration of the current video sequence.
Weight of the current video sequence.
61- Video
At the back of the phone, a cover protects the lens of the video recorder. Please remember to
open it before filming. A message is displayed if you try to launch the video application and the
lens cover is not open.
Closed lens
cover
Lens
Slide the
lens cover
open
How to hold your phone to make videos
Subject behind the phone
To record a video
You can record videos up to 5MB. These videos can be stored either on your mobile or on a
miniSD™ Card (see "To select the storage memory", page 65)
1
Open the lens cover (see the drawings above) then press and hold the [Menu]
or
side key
1’ Press and hold the [Camera/Video]
side key then open the lens cover.
or
1’’ Open the lens cover, then press on the [Menu]
side key and select Video recorder.
2 Choose a subject.
3 Press the [Camera/Video]
side key to launch the Recording.
The shutter sound is played and the red light is activated.
4 Press the [Menu]
side key to stop the Recording.
1. When the gauge reaches its limit, the Recording is automatically stopped.
2. Do not forget to close the lens cover after recording a video otherwise it covers the loud speaker.
63- Video
Setting the video to Pause
This mode allows you to record several sequences on a single file. During the Recording you
can pause your video in the following way:
1
2
During the recording, press the [Camera/Video]
key and the recorded sequence is
paused.
Press the [Camera/Video]
key to restart the Recording.
The red light is deactivated during the Pause mode.
Storing/erasing your video
When a video has been recorded (see "To record a video", page 63), the file name and the
«Keep this video?» message are displayed.
1
press OK to store the video or select Clear to erase it.
The recorded video is stored in the Video folder of the Fun & Media box menu (please see "Videos",
page 73) except if you have previously chosen to have it stored on the miniSD™ Card (please see
"To select the storage memory", page 65). The video file is stored as a .3gp file.
Sending your video
You can also send your video by Mail, by MMS or via the infrared port.
1
2
Select Options, then select Send by...
Select Mail, MMS or Infrared port, then follow the displayed instructions.
Adjusting the preview
You can preview settings before making a video. These settings can be accessed from an items
menu on the preview screen by pressing the [Menu] side key.
To switch to the camera application
This item allows you to switch from the video application to the camera application to take a
picture.
1
2
Press the [Menu]
side key. Select Camera.
Press the [Camera/Video]
side key to confirm your selection.
To select the image size
1
2
3
Press the [Menu]
side key. Select Resolution.
Select the Normal or the Small mode.
Press the [Camera/Video]
side key to confirm your selection.
To select the image quality
This setting allows you to choose a quality level for your video. The better the quality, the bigger
the file size. If you wish to send your video by Mail or by MMS, we advise you choose the Economic mode.
1
2
3
Press the [Menu]
side key. Select Quality.
Select the Super fine, the Fine or the Economic mode.
Press the [Camera/Video]
side key to confirm your selection.
To select the brightness
1
2
3
Press the [Menu]
side key. Select Brightness.
Select one of the seven brightness levels.
Press the [Camera/Video]
side key to confirm your selection.
To select the zoom setting
1
2
3
Press the [Up]
or [Down]
side key.
Select one of the zoom levels by scrolling left ( ) or right ( ).
Press the [Camera/Video]
side key to confirm your selection.
64- Video
To access the microphone setting
This setting allows you to activate or mute the microphone during the recording.
1
2
3
Press the [Menu]
side key. Select Microphone.
Select On or Off.
Press the [Camera/Video]
side key to confirm your selection.
To access the video size limit setting
By setting the size limit of your video file(up to 5MB), the recording will stop automatically
once it reaches this limit for Mail or MMS message.
1
2
3
Press the [Menu]
side key. Select Video size limit.
Select Short mail, Long mail or Maximum size.
Press the [Camera/Video]
side key to confirm your selection.
The Fit to mail value depends on your operator (min: 100 KB, max: 300 KB).
To select the storage memory
Before launching a video record, you have to choose where to store your video file. Phone Memory
is the default setting.
1
2
3
Press the [Menu]
side key. Select Storage.
Select Phone memory or Memory card.
Press the [Camera/Video]
side key to confirm your selection.
To access the compact light setting
Use the compact light when you need to light up your subject during the video recording.
1
2
3
Press the [Menu]
side key. Select Compact light.
Select On or Off.
Press the [Camera/Video]
side key to confirm your selection.
To access the self timer
The self timer offers the possibility of recording a delayed video, thereby enabling you to be in
the video.
1
2
3
4
Press the [Menu]
side key. Select Self timer.
Select On.
Press the [Camera/Video]
side key to launch the countdown.
The 10 seconds countdown is displayed on the external screen. The recording is automatically launched when the countdown is over. Please proceed as usual (to stop or pause the
video).
Press on the [Menu]
side key to stop the recording.
If an event occurs (Mail, MMS reception...) or the phone’s behaviour is modified (any key pressed, clamshell
opened or closed...) after the countdown has started, the self timer is automatically stopped and set to Off.
Once the event has been processed, the phone returns to the preview screen.
To display/conceal information icons
This option allows you to activate or conceal the phone information status icons display on top
of the screen (see "Video recorder icons", page 61)
1
2
3
Press the [Menu]
side key. Select Info.
Select On (the icons are displayed) or Off (the icons are not displayed).
Press the video
side key to confirm your selection or press the [Menu]
the information icon panel.
side key to exit
Macro switch setting
The macro switch allows you to set the focus of the video recorder in order
to film very close items.
65- Video
Open clamshell: self-filming
The video feature, with open clamshell, is to be used with the keypad only. This is used to:
- film yourself
- play the stored videos in an optimised resolution.
[Up] side key
Camera & Video lens
Navigation key
[Down] side key
[Ok] key
Available shortcuts:
Each of the video-related keys has several functions. While using the video feature, please use
the keypad as follows:
KEYS
DESCRIPTION
[Up] side key
[Down] side key
[OK] key
To zoom out.
To zoom in.
To launch the Recording in Preview or Pause mode.
To launch the Pause mode in Recording.
To access the Zoom panel and to scroll to the next one.
To access the Quality panel and to scroll to the next one.
To access the Brightness panel.
[Up] navigation key
[Down] navigation key
[Left] navigation key
The settings described above are to be accessed via the Preview mode only.
How to hold your phone to make videos
Subject in front of the phone (for self-filming)
66- Video
To access the video application
You can access the video recorder application in the following way:
1
From the standby display, press and hold the [OK] key.
1
2
From the idle screen, press the [Menu/T9] key. Select Camera/Video.
Select Film a video.
or:
The infrared port automatically closes when the video application is accessed
To film yourself
You can record videos up to 5 MB. These videos can be stored either on your phone or on a
miniSD™ Card (please see "To select the storage memory", page 68).
To film yourself the phone displays mirrored images on the main screen. During the recording,
opening or closing the clamshell sets the recording to Pause.
1
2
3
4
Place yourself in front of the mobile so that your image is displayed on the main screen.
Adjust the required settings (see "Adjusting the preview", page 67).
Press OK to launch the recording.
Select Stop (right softkey) to stop the recording.
An Options list is then available:
OPTIONS
DESCRIPTION
Play
To play the recorded video (please see "How to play your video", page 70 for
full details on the Options submenu).
To send the video by Mail, by MMS or via the infrared port.
To delete the current video.
To display information about the file Name, the Title, the Author (the device
name), the Resolution (width*height in pixels), the Duration of the video, the
Size, the Storage date, the File protection status, the Description (if a text is
attached to the video file), the Copyright of the recorded video, the Restriction
status. The empty fields are not displayed.
Send by
Delete
Details
1.When the record mode is launched the shutter sound is played and the red light is continuously On.
2.When the video reaches its maximum size (see "To access the video size limit setting", page 65), the
Recording is automatically stopped.
Setting the video to Pause
This mode allows to record several sequences on a single file. During the recording you can
pause your video in the following way:
1
2
During the recording, press OK. When setting the video to Pause, the red light is turned Off.
Press OK to restart the Recording.
Storing/erasing your video
After recording(see "To film yourself", page 67), the file name and the "Keep this video?"
message are displayed.
1
Select OK to store the video or select Clear to erase it .
The video is automatically stored in the Video sub-folder of the Fun & Media box menu (see
"Videos", page 73) except if you have previously chosen to have it stored on the miniSD™ Card
(please see below). The video file is stored as a .3gp file.
Adjusting the preview
Before recording, you can access the following Options list in order to set your Preview
details.
OPTION
DESCRIPTION
Camera
Settings
Compact light
Self timer
Microphone
To switch from the Video application to the Camera application.
To access a settings list (see the table below).
To turn the Compact light On/Off.
For automatic launching of the video recording after a 10 second countdown.
To activate/mute the microphone.
67- Video
You can adjust your videos settings before recording.
1
2
From the preview screen, select Options.
Select Settings:
ITEMS
DESCRIPTION
Image
resolution
Image quality
Storage
To select the video frame size. Select Normal or Small mode.
Shutter sound
level
Compact light
intensity
Info
Video size limit
3
4
To select the image quality. Select Super fine, Fine or Economic.
To set the Phone memory or the miniSD™ Card as the storage memory
space.
To select the shutter sound volume level.
To select the intensity level of the compact white light. Select High, Medium
or Low.
To display/conceal the pictographs (preview mode only).
To display the maximum allowed video size. Select Fit to mail or Maximum
size.
Fill in the available entries and select OK to validate your entries.
Select Save to store the changes.
You cannot deactivate or mute the shutter sound Option on your phone.
To select the storage memory
Before launching a video recording you have to choose the storage space the video will be
stored in. If you do not choose a storage space, the video is stored on the phone memory by
default.
1
2
3
4
From the Preview, select Options then Settings
Select Storage.
Select Phone memory or Memory card.
Select Save to store your setting.
How to play your video
You can watch, on the main screen, a video that has just been recorded before storing it in the
following way:
1
2
Select Options.
Select Play.
To have more information about the video player please see "To play a video", page 74.
68- Video
FUN & MEDIA BOX
his menu helps you to organize and manage all the images, melodies, videos,
speech notes, frames, Games and Java applications contained in the phone
as well as all the files received via the WAP™ browser, the infrared port, Mail,
MMS or SMS.
T
Pictures
The Pictures sub-menu allows you to view and set stored (via the Camera and the Infrared port)
still and animated images (animated .gif) as a standby display for your Main screen (internal
screen) or External (with still pictures only) screen, a Welcome or a Goodbye screen in order
to configure and personalise your phone screens (see "Display", page 95). The picture formats
supported by your phone are .wbmp, .gif, .jpg, .png, .swf, .ifm.
Internal screen
External screen
Welcome screen/
Goodbye screen
You can download images via the WAP™ browser and mailer, via the Infrared port and by
MMS. It is then possible to store them and/or set them as a Standby display for your internal
and external screens, a Welcome screen or a Goodbye screen.
Your phone allows you to set one Standby display for your internal screen, one Standby display
for your external screen (still pictures only), one Welcome screen or one Goodbye screen from
the downloaded and/or stored images (to download and store images, see the following sections).
Pictures browser
The Pictures browser allows you to display the stored images
as a list or as a mosaic. When the pictures are displayed as a
list the screen is divided into two parts: the image names list
and the selected image. When they are displayed as a mosaic
(Thumbnails mode: see ’Options/My preferences’ below) the
screen contains a mosaic of pictures (4 or 9 pictures) and the
name of the selected image.
Viewing an image
1
2
3
4
Press the [Menu/T9] key. Select Fun & Media box.
Select Pictures.
Scroll down the images list or mosaic. Select the required image or select a folder to view its
contents (press OK).
Press OK or Options and View to view the selected image in full size.
69- Fun & Media box
Options
The Pictures folder Options list contains the following items:
OPTIONS
DESCRIPTION
View
To view the full image and name.
To set the image as a Main screen, as an External screen, as a Welcome
screen (on the internal screen only) on switching on your phone or as a
Goodbye screen, (on the internal screen only) on switching it Off.
Send by...
To send the image via infrared port, by Mail or by MMS.
Delete
To delete the current image.
Delete all
To delete all the pictures of the current folder.
To select several images (by pressing OK). Press OK to unselect a ticked
image. Select Options to access Send by... (Infrared port), Delete, Move to
Multiple
(a folder of Pictures or the miniSD™ Card), Copy to (a folder of Pictures or
selection
the miniSD™ Card), Select all (to select all the files of the current folder),
Unselect all (to unselect all the ticked files).
To move the current image to the Pictures folder, to one of the Pictures subMove to
folders or to the miniSD™ Card.
To copy the current image to the Pictures folder, in one of the Pictures subCopy to
folders or the miniSD™ Card.
To create a sub-folder in the Pictures folder (available only if the selection
New folder
is not a folder already).
Rename
To rename the current picture.
To show the name, resolution, size, storage date and protection status of
Details
the current file.
To sort the stored images (by date, name, size) and select a view mode
My preferences (List, Thumbnails 4 - to display a 4-picture mosaic - or Thumbnails - 9 to
display a 9-picture mosaïc) and to change the Picture browser mode.
Set as...
1. If the selection is a sub-folder, an Options list is available: View, Delete, New folder and My preferences.
2. The sending of an image may not be allowed if it is exportation (copyright) protected (the ’File protected’
message is then displayed).
3. To send an image via the infrared port please see "Infrared port" on page 19. To send an image via Mail
(please see "Composing an e-mail", page 38) and via MMS (please see "Writing and sending a multimedia message",
page 34).
4. If there is error messages,please see "Error messages" on page 109 for details.
5. You can only access the miniSD™ Card storage space if the miniSD™ Card is inserted in the phone.
When viewing an image, an Options menu is available (only for still and animated .gif pictures):
OPTIONS
DESCRIPTION
Full view
To view the picture in full screen.
To set the image as a Main screen, as an External screen or as a Welcome
screen on switching on your phone or as a Goodbye screen on switching it Off.
To send the picture via the Infrared port (the infrared port is automatically
Send by...
open), by Mail or by MMS.
Delete
To delete the current picture.
To rotate the picture to the right (90°), to the left (90°) or turnover (180°).
Once the picture is rotated, an Options menu is available to store the current
Rotate...
picture, to view it in Full screen, to Cancel the rotation, to Add a frame to the
current picture or to Rotate it once again.
Slide show
To display automatically all the pictures of a folder one after another.
Add frame...
To add a frame to the current picture.
To show the name, resolution, size, storage date and protection status of
Details
the current file.
While viewing a picture in full screen, press the left soft key underneath
to access the three
available zoom level (Maximum, Medium and Minimum).
Set as...
70- Fun & Media box
Screen Settings
This option allows you to set a picture as a standby screen image on the internal and external
screens or as a Welcome or a Goodbye screen .
SCREEN
AVAILABLE PICTURE TYPES
Main screen (internal screen)
External screen
Welcome screen (main screen)
Goodbye screen (main screen)
Still and animated pictures (animated .gif).
Still pictures.
Still and animated pictures (animated .gif).
Still and animated pictures (animated .gif).
1
2
3
4
Press the [Menu/T9] key. Select Fun & Media box.
Select Pictures.
Use the [Up] and [Down] arrow keys to scroll through the image names list and select one.
Select Options and then Set as...
Select Set as Main screen, Set as External screen, Set as Welcome screen or Set as
Goodbye screen.
Cropping
If the image you want to set as an Standby display is too large to be inserted into the available
space, your phone will propose a cropped image.
This allows you to move the image left, right, up and down (cursor key). The image you have cropped is then displayed as such on the phone (as a Standby
display).
1
2
3
Select Set as... then select Standby display. If the image is too big, the crop
screen is displayed.
Use the cursor key to move the image up, down, left or right (the availability
of the four arrows depends on the image size).
Select OK. Stored is then displayed.
Receiving images via the infrared port
1
2
3
Open the infrared port (see "Infrared port", page 19) and make sure that the infrared port of the
other appliance is facing your phone infrared port so that the image transfer is carried out correctly.
When you have received an image, select Options then select Full screen.
Select Options then Details to show the name, resolution, size, storage date and protection
status of the current file.
1. The images you receive via the infrared port are automatically stored in the Fun & Media box Pictures folder.
2. To select and activate a Standby display for your Main screen, your External screen, your Welcome screen or
your Goodbye screen, see "Pictures", page 69.
3. You can also receive pictures by MMS and by Mail.
To access images stored on your miniSD™ Card
You can view pictures that are stored on your miniSD™ Card. The Options lists are the same
as in the Pictures sub-menu.
1
2
3
4
Press the [Menu/T9] key. Select Fun & Media box.
Select Pictures, then Memory card (this item is only displayed when a miniSD™ Card is
inserted).
Select the required picture or choose a folder (press OK to view its content) then select a picture.
Press OK or Options and Full view to view the selected image in full size.
71- Fun & Media box
Melodies
This sub-folder allows you to play/store pre-defined melodies or melodies you downloaded via
the Infrared port or via the WAP™ browser, or you received by SMS, by Mail or by MMS. You
can set these melodies as a ringtone for Line1 or Line2, an Alarm melody, a Message alarm
melody, a Welcome or Goodbye melody. The melody formats supported by your phone are
.smf, .mfi, .mid, .mfmp, .3gpp, .amr and Nokia™ Smart Messaging.
Melodies
To display the Melodies file contents
1
2
3
Press the [Menu/T9] key. Select Fun & Media box.
Select Melodies.
Use the [Up] and [Down] arrow keys to scroll to the required melody.
The following Options list is available while scrolling the melodies list..
OPTIONS
DESCRIPTION
To play the selected melody. Scroll up ( ) or down ( ) to set the melody
volume during the playback.
To set the selected melody as a Ringtone for Line1 or Line2, as an Alarm
Set as...
melody, as a Message alert melody or as a Welcome melody or a Goodbye
melody.
Send by...
To send the selected melody by Mail, by MMS or via the Infrared port.
Delete
To delete the current melody.
Delete all
To delete all the melodies of the current folder.
To select several melodies (by pressing OK). Press OK to unselect a ticked
melody. Select Options to access Send by... (Infrared port), Delete, Move to
Multiple
(a folder of Melodies or the miniSD™ Card), Copy to (a folder of Melodies
selection
or the miniSD™ Card), Select all (to select all the files of the current folder),
Unselect all (to unselect all the ticked files).
To move the selected file to the miniSD™ Card or to one of the Melodies
Move to
sub-folders.
To copy the selected file in the miniSD™ Card or to one of the Melodies subCopy to
folders.
To create a new sub-folder in the Melodies folder (available only if the
New folder
selection is not a folder already).
Rename
To rename the selected melody.
To view the current file name, size, storage date and file protection status
Details
information.
My preferences To sort the stored melodies (by date, name, size).
Play
You can only access the miniSD™ Card storage space if the miniSD™ Card is inserted in the phone.
If the selection is a sub-folder, another Options list is available: View, Delete, New folder and
My preferences.
Melody download
You can download melodies from the Internet (via your PC), from interactive voice servers,
from the WAP™ browser and mailer or via the infrared port .
In addition to the usual SMS download of melodies, you can download melodies by browsing
internet web sites.
Mitsubishi Electric phones are compatible with the Nokia™ Smart Messaging system. The principle is as follows:
1
2
3
4
5
Melodies are stored on a Web server.
Select your Mitsubishi Electric phone type to access a choice of melodies.
Select one or more melodies to be downloaded to your phone.
All selected melodies are downloaded via SMS.
Once the melody is received, a reception screen is displayed. Press OK or select Options
then Play to play the received melody.
To set a melody as a ringtone, a message alert melody, an alarm melody, a Welcome or a
Goodbye, please see "Tones", page 94.
You can also receive melodies via the Infrared port.
72- Fun & Media box
Formats managed by the phone are .mid, .mfm, .3gp, .mld, .amr, .nsm and .imy formats.
To play a downloaded melody from the reception screen:
1
2
Select OK or select Options then Play.
Select Exit to stop the playback.
To store a downloaded melody:
1
2
Select Options.
Select Install.
If the memory space is sufficient, the melody is automatically stored in the Melodies file. If
there is no space left, you need to select one or several melody(ies) to be replaced from the
set of melodies (melodies associated with a ring feature cannot be deleted).
Once stored, a message is displayed. The melody can be played and selected via the
Fun & Media box menu.
To discard a downloaded melody:
1
Select Discard. The melody is erased and is therefore lost for further installation.
To access melodies on your miniSD™ Card
You can store or play melodies on your miniSD™ Card. The Options lists are the same as in
the Melodies sub-menu.
1
2
3
4
Press the [Menu/T9] key. Select Fun & Media box.
Select Melodies, then Memory card (this item is only displayed when a miniSD™ Card is
inserted).
Scroll up or down to select the required melody or choose a folder (press OK to view its content) then select a melody.
The melody is played within 2 seconds
Videos
This sub-menu allows you to play videos that are stored on your phone. You can also send
and receive these videos by Mail, MMS or via the Infrared port. The video file format supported
by your phone is .3gp.
To access videos stored on your phone
1
2
3
Press the [Menu/T9] key. Select Fun & Media box.
Select Video.
Scroll up and down to select the required video or select the required folder
(press OK to view its content) then the required video.
Select Options to access the followings:
OPTIONS
DESCRIPTION
Play
Send by...
Delete
Delete all
To play the selected video.
To send the selected video by Mail, by MMS or via the Infrared port.
To delete the current video.
To delete all the videos in the current folder.
To select several videos (by pressing OK). Press OK to unselect a ticked
video. Select Options to access Send by... (Infrared port), Delete, Move to
(to one of the Video sub-folders or to the miniSD™ Card), Copy to (a folder
of Videos or the miniSD™ Card), Select all (to select all the files of the
current folder), Unselect all (to unselect all the ticked files).
To move the selected file to the miniSD™ Card or to one of the Videos subfolders.
To copy the selected file in the miniSD™ Card or in one of the Videos subfolders.
To create a new folder in the Vidoes sub-folder (available only if the
selection is not a folder already).
To rename the selected video.
Multiple
selection
Move to
Copy to
New folder
Rename
73- Fun & Media box
To view the current file name, size, storage date and file protection status
information.
My preferences To sort the stored videos (by date, name, size).
Details
You can only access the miniSD™ Card storage space if the miniSD™ Card is inserted in the phone.
If the selection is a sub-folder, another Options list is available: View, Delete, New folder and
My preferences.
To play a video
To get an optimised playback of your video, please watch it on the internal
screen:
1
Press the [OK] key to play the selected video.
During the Play mode, during the Pause mode or when the video is stopped you
can access the following options list:
OPTIONS
DESCRIPTION
Volume
Full screen
Loop mode
Send by...
Details
To set the sound volume level (from 0 to 7).
To play the video on full screen.
To play the video repeatedly.
To send the current video via the infrared port, by an MMS or by a Mail.
To display information about the file Name, the Title, the Author (the device
name), the Resolution (width*height in pixels), the Duration of the video, the
Size, the Storage date, the File protection status, the Description (if a text is
attached to the video file), the Copyright of the recorded video, the Restriction
status. The empty fields are not displayed.
1. When the video track cannot be played or if there is no video track, the audio track only is played. The
«Audio only» message is displayed.
2. During the Play mode opening or closing the clamshell sets the video to Pause. Press OK to re-start the
playback.
3. You cannot play a video while a communication is in progress.
4. If an event (alarm, SMS receipt...) occurs while a video is being played, the playback is stopped.
To play the videos that you received by Mail or by MMS, please see "Saving received multimedia message content", page 34 and "Reading a received e-mail", page 39. To play the videos
that are on a miniSD™ Card, please see "To access melodies on your miniSD™ Card", page 75.
While playing the video you can use the following shortcuts:
KEYS
From
&
DESCRIPTION
to
To mute the sound volume.
To set the sound volume level (from 1 to 7).
To set the sound volume level to the maximum value.
To activate/deactivate the loop mode.
To activate/deactivate the full screen mode.
To launch the Playback mode while in Stop mode or in Pause
mode.
To pause the video in Playback mode.
To increase the sound volume level by one level (short press) or
by several levels (long press).
To decrease the sound volume level by one level (short press) or
by several levels (long press).
To stop the Playback.
74- Fun & Media box
How to play your video on the external screen
You can also watch the videos stored on your phone or on the miniSD™ Card (see " To access
videos stored on your miniSD™ Card", page 75) on the external screen. However, to get an
optimised display of the videos we advise you watch them on the internal screen.
1
2
3
4
5
6
Open the clamshell.
Press the [Menu/T9] key. Select Fun & Media box.
Select Videos, then select the required video.
Press OK or select Options, then Play.
Close the clamshell. The video is paused.
Press the [Camera/Video]
side key to start the Play mode.
You cannot play a video while a communication is in progress.
Full screen option
This option allows you to watch videos on full screen. Please hold your phone horizontally to
enjoy an optimised display of the video. You can use the side keys to play, pause or stop the
video or to set the sound volume.
Receiving videos via the infrared port
1
2
Make sure the infrared port of the other appliance is facing your phone infrared port. Your
phone infrared port automatically opens when the other appliance sends the file.
When you have received a video, select Options then select Play to watch the video, select
Details to view the current file name, resolution, duration, size, storage date and file protection status information or select Delete to erase it.
To access videos stored on your miniSD™ Card
You can play videos that are stored on your miniSD™ Card.The Options lists are the same as
in the Videos sub-menu.
1
2
3
4
Press the [Menu/T9] key. Select Fun & Media box.
Select Videos, then Memory card (this item is only displayed when a miniSD™ Card is
inserted).
Scroll up or down to select the required video or choose a folder (press OK to view its content) then select a video.
Press the [OK] key to play the selected video.
Music
This sub-folder allows you to play/store MP3 melodies you downloaded via the Infrared port or
via the WAP™ browser, or that you received by SMS, by Mail or by MMS. You can set these
melodies as ringtones for Line1 or Line2, as an Alarm melody, a Message alarm melody, a Welcome or a Goodbye melody.
Music
To display the Music file contents
1
2
3
Press the [Menu/T9] key. Select Fun & Media box.
Select Music.
Use the [Up] and [Down] arrow keys to scroll to the required melody.
75- Fun & Media box
The following Options list is available while scrolling the melodies list..
OPTIONS
DESCRIPTION
To play the selected music. Scroll up ( ) or down ( ) to set the music
volume during the playback.
To set the selected melody as a Ringtone for Line1 or Line2, as an Alarm
Set as...
melody or as a Message alert melody.
Send by...
To send the selected music file by Mail, by MMS or via the Infrared port.
Delete
To delete the current music file.
Delete all
To delete all the music file from the current folder.
To select or deselect musics(by pressing OK).
Select Options to access Send by... (Infrared port), Delete, Move to (a folder
Multiple
of Music or the miniSD™ Card), Copy to (a folder of Music or the miniSD.
selection
Card), Select all (to select all the files of the current folder), Unselect
all (to unselect all the ticked files).
To move the selected file to the miniSD™ Card or to one of the Music subMove to
folders.
To copy the selected file in the miniSD™ Card or to one of the Music subCopy to
folders.
To create a new sub-folder in the Music folder (only applicable to music
New folder
selection).
Rename
To rename the selected music.
To view the current file name, size, storage date and file protection status
Details
information.
My preferences To sort the stored music (by date, name, size).
Play
You can only access the miniSD™ Card storage space if the miniSD™ Card is inserted in the phone.
If the selection is a sub-folder, another Options list is available: View, Delete, New folder and
My preferences.
To play the Music file
1
2
3
4
Press the [Menu/T9] key. Select Fun & Media box.
Select Music.
Use the [Up] and [Down] arrow keys to scroll to the required melody.
Press OK or select Options then Play to play the Music file.
While playing a Music file, you can switch from the Loop mode to the Play all mode by pressing
the left softkey.
Music download
You can download music from the Internet (via your PC), from interactive voice servers, from
the WAP™ browser and mailer or via the infrared port .
You can download music by browsing internet web sites:
1
2
3
When on a webpage containing MP3 files press Option and Attachement.
On the list of the files available select the required file.
Press Option (left softkey) and Store to store the selected music file on your phone. The file
is store in the Music folder.
You can also receive music files via the Infrared port.
Formats managed by the phone are MP3 .mid, .mfm, .3gp, .mld, .amr, .nsm and .imy formats.
To play a downloaded music files from the reception screen:
1
2
Select OK or select Options then Play.
Select Exit to stop the playback.
To store a downloaded music
1
2
Select Options.
Select Install.
If the memory space is sufficient, the melody is automatically stored in the Melodies file. If
there is no space left, you need to select one or several melody(ies) to be replaced from the
set of melodies (melodies associated with a ring feature cannot be deleted).
Once stored, a message is displayed. The melody can be played and selected via the
Fun & Media box menu.
76- Fun & Media box
To discard a downloaded music:
1
Select Discard. The music file is erased permanently.
To access music on your miniSD™ Card
You can store or play music files on your miniSD™ Card. The Options lists are the same as in
the Music sub-menu.
1
2
3
4
Press the [Menu/T9] key. Select Fun & Media box.
Select Music, then Memory card (this item is only displayed when a miniSD™ Card is
inserted).
Scroll up or down to select the required melody or choose a folder (press OK to view its content) then select a melody.
The melody is played within 2 seconds.
Speech notes
This feature allows you to record speech notes up to 25 minutes on your phone.
To record a speech note
1
2
3
4
5
Press the [Menu/T9] key. Select Fun & Media box.
Select Speech note.
If no speech note has been recorded, select New. If one/several speech note(s) is/are stored
in the phone, select Options then Record new.
Select Stop to end the recording.
Enter the note name and press OK.
To select a speech note.
1
2
3
Press the [Menu/T9] key. Select Fun & Media box.
Select Speech notes.
Scroll up or down to select the required speech note or the required folder.
OPTIONS
DESCRIPTION
Play
Record new
To play the selected speech note(s).
To record a new speech note.
To set the selected speech note as a ring tone for Line1 or Line2, as an
Set as...
alarm melody, as a message alert melody or as a Welcome or a Goodbye
melody.
Send by...
To send the speech note via the Infrared port, by MMS or Mail.
Delete
To delete the current speech note.
Delete all
To delete all the speech notes of the current folder.
To access the Multiple selection screen and select several speech notes.
You can then select Options to Send the selected file(s) by infrared port, to
Multiple
Delete the selected file(s), to Move them to a Speech notes sub-folder or to
selection
the miniSD™ Card, to Copy them to a Speech notes sub-folder or to the
miniSD™ Card, to Select all the speech notes or to Unselect all the ticked
speech notes.
To move the selected speech note to the miniSD™ Card or to a Speech
Move to
notes sub-folder.
To copy the selected speech note to the miniSD™ Card or to a Speech
Copy to
notes sub-folder.
To create a new folder in the Speech note sub-folder (only available if the
New folder
selection is not a folder already).
Rename
To change the name of the current speech note.
To view information about the name, file size and recording date, and file
Details
protection status.
My preferences To sort the stored images (by date, name, size).
You can only access the miniSD™ Card storage space if the miniSD™ Card is inserted in the phone.
If the selection is a sub-folder, an Options list is available: View, Record new, Delete, New folder and My preferences.
77- Fun & Media box
To play a speech note
1
2
3
Press the [Menu/T9] key. Select Fun & Media box.
Select Speech note.
Scroll up or down to the required speech note. Press OK or Select Options then select
Play.You can set the speech note volume by scrolling Up ( ) or down ( ).
To access speech notes stored on your miniSD™ Card
You can store (see "To record a speech note", page 79 ) or play speech notes that are stored
on your miniSD™ Card. The Options lists are the same as in the Speech notes sub-menu.
1
2
3
4
Press the [Menu/T9] key. Select Fun & Media box.
Select Speech notes, then Memory card (this item is only displayed when a miniSD™ Card
is inserted).
Scroll up or down to select the required speech notes or choose a folder (press OK to view
its content) then select speech note.
Press OK or select Options then select Play.
Frames
The frame border feature allows you to illustrate your pictures and give them a more personal
and fun touch. You can add frames, speech balloons, etc. to the pictures stored in the Pictures
folder or while doing your picture preview.
The frame folder contains all files that can be used as frame borders on the phone and may
contain pre-embedded frames and sub-folders. The frame file type supported by your phone is
.gif.When adding a frame to a picture, the new image is stored as .jpg file.
It is not possible to add a frame to a video.
Frames browser
The Frames browser allows you to display the stored frames as a list or as a mosaic of frames. When the frames are displayed as a list the screen is divided into
two parts: the frames names list and the selected frame. When they are displayed as a mosaic (Thumbnails mode: see ’Options/My preferences’ below) the
screen contains a mosaic of frames and the name of the selected frame.
While browsing the Frames folder the following Options list is available (left
softkey):
OPTIONS
DESCRIPTION
View
Delete
Delete all
To view the frame and its name.
To delete the current frame.
To delete all the frames of the current folder.
To select several frames (by pressing OK). Press OK to unselect a ticked
Multiple
frame. Select Options to access Delete, Move to (a Frames sub-folder),
Copy to (a Frames sub-folder), Select all (to select all the files of the current
selection
folder), Unselect all (to unselect all the ticked files).
Move to
To move the current image to the Frames folder or to one of the Frames sub-folders.
Copy to
To copy the current image in the Frames folder or to one of the Frames sub-folders.
New folder
To create a sub-folder in the Frames folder.
Rename
To rename the current picture.
To show the name, resolution, size, storage date and protection status of
Details
the current file.
To sort the stored frames (by date, name, size) and select a view mode
My preferences (List, Thumbnails 4 to display a 4-frame mosaic or Thumbnails 9 to display
a 9-frame mosaic) to change the Frames browser mode.
1. If the selection is a sub-folder, another Options list is available.
2. You cannot transfer a frame out of the Frames folder (e.g. to the miniSD™ Card).
3. Error messages may be displayed when setting, viewing or storing an image:’File too big’ (please see "Error
messages", page 111); ’Decoding failure’: the frame cannot be viewed by the phone.
4. The miniSD™ Card is not accessible from the Frames folder.
78- Fun & Media box
Viewing a frame
1
2
3
4
Press the [Menu/T9] key. Select Fun & Media box.
Select Frames.
Scroll the frames list or mosaic. Select the required frame or select a folder to view its content (press OK).
Press OK or Options then View to view the selected frame in full size.
An Options menu is available.
OPTIONS
DESCRIPTION
Full view
Delete
Slide show
To view the frame in full screen.
To delete the current picture.
To automatically display all the frames of the selected folder one after another.
To show the name, resolution, size, storage date and protection status of
Details
the current file.
Adding a frame to your picture
This feature allows you to add a frame to your preview (internal or external screen) before capturing an image. According to the selected frame, you may need to use your phone horizontally
or vertically in order to make the preview screen content fit your frame.
Closed clamshell
1
2
3
4
5
From the standby display, press the [OK] key to access the Camera application.
Select Options then Frames. The frames list or mosaic is displayed.
Scroll down the frames list or mosaic. Select the required frame or select a folder then select
the required frame. A preview with the selected frame over your picture is displayed so that
you can define your picture settings and view the final result.
Press OK to confirm your selection.
Close the clamshell then open the lens cover. Your preview with the selected frame is displayed. Capture your image (please see "To take a picture", page 56)
1. The new picture is stored in the Pictures folder as a .jpg file.
2. When taking a picture, the preview size is automatically adapted to the selected frame size. Modifying the
preview size removes the frame.
Open clamshell
1
2
3
4
5
From the standby display, press the [OK] key to access the Camera application.
Select Options then Frames. The frames list or mosaic is displayed.
Scroll down the frames list or mosaic. Select the required frame or select a folder then select
the required frame. A preview with the selected frame over your preview is displayed so that
you can define your picture settings and view the final result.
Press OK to confirm your selection.
Press OK to capture your picture.
1. The new picture is stored in the Pictures folder as a .jpg file.
2. To take self-portraits the phone displays mirrored images on the main screen.
3. When capturing a picture, the preview size is automatically adapted to the selected frame size. Modifying
the preview size removes the frame.
Adding a frame to a stored picture
This feature allows your to add a frame to a stored image.
1
2
3
4
5
6
7
Press the [Menu/T9] key. Select Fun & Media box.
Select Pictures.
Scroll down the frames list or mosaic. Select the required frames or select a folder then
select the required picture.
Select Options then Add frame. The frames list or mosaic is displayed.
Scroll down the frames list or mosaic. Select the required frame or select a folder then select
the required frame. A preview screen with the selected frame over the current picture is displayed so that you can view the final result.
Press OK to confirm your selection. The new picture and its name are displayed.
Select Options then Store to save the new picture.
1. The new picture is stored in the Pictures folder as a .jpg file. In case of format conversion the quality of the
new picture is not guaranteed.
2. The picture size is adapted to the frame size.
3. If the source picture is protected by a copyright, you may not be allowed to add a frame to this picture.
79- Fun & Media box
Frames downloading
You can download frames via the WAP™ browser (please see "Go to site", page 93).It is not
possible to send or to transfer a frame to a folder other than the Frames folder or to another
device (the miniSD™ Card, a PC, etc.). The frames you received via the WAP™ browser, by
e-mail and MMS are automatically stored in the Frames folder.
If the download frame format is not recognized by the phone, the frame file is stored as a picture.
Java™ applications
Java™ and all Java-based trademarks and logos are trademarks or
registered trademarks of Sun Microsystem, Inc., in the US
and other countries.
This sub-menu allows to launch Java™ games and applications that are stored on your phone,
and upgrade or delete downloaded games and applications.
Your phone may not bear pre-stored games and/or applications (operator dependent).
To launch a java™ application
1
2
3
4
Press the [Menu/T9] key. Select Fun & Media box .
Select Applications.
Select Applications to launch a game or an application you previously downloaded on your
phone (see "To download a java™ application", page 83) or Default apps. to launch a preembedded game or application.
Select one of the available games and applications or select Options and then select Run.
When on the dowloaded application list the following options submenu is available:
OPTIONS
DESCRIPTION
View
Run
Delete
Delete all
To view the application detailed content.
To launch the game or the application.
To delete a game or an application.
To delete the stored games and/or applications.
To modify the security permissions of the midlet suite. This option gives
access to the Set up call, Set up connection, Send an SMS, Auto-start app.
and User IrDA/serial options.
To view the game/application name, size, version and manufacturer.
Permissions
Details
1. The Default applications menu is not available if no pre-embedded application is available.
2. The contents of the Option menu may change from a game/application to another.
When running a game and/or application actions are linked to the following keys:
KEY
ACTION
OK and
To move left.
To move right.
To move down.
To move up.
To fire.
Game D.
Game A.
Game B.
Game C.
1. Access to actions on keys
,
,
and
depends on the current game. The actions linked to these keys
may depend on the launched game or application. Please read the game/application instructions for full details.
2. Beware: If the features of the dowloaded game(s) do not comply with the phone capabilities, the application
may not run properly.
3. Receiving an incoming call while playing may not allow you to resume the current game.
80- Fun & Media box
To download a java™ application
Java™ applications are to be downloaded via the Wap™ application (please see "Starting a
Wap™ session", page 90):.
1
2
2
2
2
Press the [Menu/T9] key. Select Fun & Media box .
Select Applications.
Select Get new apps ans select Yes to allows the connection to the WAP™ server.
Once on a Wap page containing Java™ games/applications, select the game/application
you want to dowload.
Select Retrieve (Left softkey) to download the game/application on your phone.
1. Games and applications download may require a delivery charge. Please check downloading and billing
conditions with your service provider.
2. You cannot install a Java™ game/application that was received by e-mail, MMS or via the infrared port
(Java™ games & applications are copyright protected).
Settings
1
2
3
Press the [Menu/T9] key. Select Fun & Media box .
Select Applications.
Select Settings.
The Settings menu is made of the following items:
ITEM
ACTION
Profiles
Select Profiles to access the list of available profiles.
Permanent Select On to set the backlight continuously On while running a Java™ game or
Backlight
application.
Selecting Off keeps the backlight standard behaviour.
When on an existing profile the options Select, View and Delete are available.
To add a profile:
A profile is a list of of parameters that allow the connection of applications when needed (please
see "storing the connection settings" on page 88 and "connection manager" on page 99):
1
2
3
4
5
6
Press the [Menu/T9] key. Select Fun & Media box .
Select Applications.
Select Settings. Select Profiles.
Select an empty profile ([...]).
Enter the Profile name.
Select Connection profiles and select or type the required information.
Please contact your service provider to get your Profile details.
To create a new profile, you can also use the assistant feature by pressing Assist. (left softkey).
Others
This menu allows you to store/view/play vcard files (Phone book), vcalendar files (Diary cards),
vbookmarks (Web bookmarks), root certificates files, text files and files with unknown/unsupported format.
To display the others file contents
1
2
3
Press The [Menu/T9] key. Select Fun & Media box.
Select Others.
Use the [Up] and [Down] arrow keys to select the required file.
81- Fun & Media box
The following Options list is available:.
OPTIONS
DESCRIPTION
View
Store
Install
To view the file contents.
To store the selected file in the corresponding application folder.
To launch the installation of a java application.
To send the text, the selected vCards, the selected vCalendars, the
vBookmark(s) and the unknown file(s) via the infrared port.
Send by...
To send the current vCard via the infrared port, by SMS or by Mail.
To send the current vCalendar via the infrared port, by SMS.
Delete
To delete the current file.
Delete all
To delete all the files of the current folder.
To select several files (by pressing OK). Press OK to unselect a ticked file.
Select Options to access Send by... (Infrared port), Delete, Move to (a folder
Multiple
of Others or the miniSD™ Card), Copy to (a folder of Others or the miniSD™
selection
Card), Select all (to select all the files of the current folder), Unselect all (to
unselect all the selected files)
Move to
To move the selected file to the miniSD™ Card or to an Others sub-folder.
Copy to
To copy the selected file to the miniSD™ Card or to an Others sub-folder.
To create a new folder in the Others folder (only available if the selected file
New folder
is not a folder already).
Rename
To rename the selected file.
To view the current file name, size, storage date and file protection status
Details
information.
My preferences To sort the stored files (by date, name, size).
1. You can only access the miniSD™ Card storage space if the miniSD™ Card is inserted in the phone.
2. The contents of this Options list may vary according to the file type.
3. You cannot send any copyright protected file (the ’File protected’ message is displayed on any attempt to
send copyright protected files).
If the selection is a sub-folder, an Options list is available: View, Delete, New folder and My preferences.
Data exchange
This feature allows the easy transfer of vCards and vCalendars to/from another device (phone,
pc,...).
Storing a received vCard
1
2
3
4
Select Options (left softkey) on the information screen when you have received the file.
Select View.
The received file is displayed. Select Store.
Select Phone names, SIM names, SIM fixed or My card. The vCard is then stored.
A received file may contain several vCards. Select the one(s) you want to keep, then select Store.
Storing a received vCalendar
1
2
3
Select Options (left softkey) on the information screen when you have received the file.
Select View.
The received file is displayed. Select Store.
A received file may contain several vCalendars. Select the one(s) you want to keep, then select Store.
Storing a received vBookmark
1
2
3
Select Options (left softkey) on the information screen when you have received the file.
Select View.
The received file is displayed. Select Store.
A received file may contain several vBookmarks. Select the one(s) you want to keep, then select Store.
82- Fun & Media box
Sending a vCard or a vCalendar by SMS
1
2
3
4
5
Select the vCard or the vCalendar you wish to transfer as explained in "Diary", page 16, "Calendar", page 16 and "Tasks list", page 18 or select it from Others.
Select Options.
Select Send by... then SMS. A warning may be displayed regarding the number of required
SMS to send the card (where more than 1 SMS is required).
Select OK if you wish to continue.
Enter the number to which you want to send the vCard or the vCalendar, or select a name
from the Names list.
To access other files stored on your miniSD™ Card
You can store or view other file types that are stored on your miniSD™ Card. The Options lists
are the same as in the Others sub-menu.
1
2
3
4
Press the [Menu/T9] key. Select Fun & Media box.
Select Others, then Memory card (this item is only displayed when a miniSD™ Card is
inserted).
Scroll up or down to select the required file or choose the required folder (press OK to view
its content) then select a file.
Select Options then select View.
Storage used
To consult the percentage of memory used for the Pictures, Melodies, Videos, Frames, Speech
note and Others folders:
1
2
3
Press the Menu/T9 key. Select Fun & Media box.
Select Storage used. The total memory used is displayed (all file types). Select Details to
view storage information per file type.
Use the [Up] and [Down] arrow keys to scroll to the required information type (Pictures, Melodies, Videos, Frames, Speech note, Others).
The Fun & Media box space is managed as a single folder. The Pictures, Melodies,Videos, Frames, Others
and Speech note files therefore share the same space in the phone.
You may not be able to store more files. You can however remove pictures, for instance, to free some space
and create a new Speech note.
83- Fun & Media box
miniSD™ Card
miniSD™ is a trade mark of SD Card Association.
The miniSD™ Card is an external device that is used as an extra storage space or a data
transferring tool. MiniSDTM Card is able to store all file formats. However you can only view
those file formats that are supported by your phone.
Please only use approved miniSD™ Card in your mobile phone. Contact your retailer for details.
The M900 mobile phone was designed to be used solely with a miniSD™ Card. Any
attempt to use another memory card type may damage the phone and be hazardous. Damage
resulting from such use shall not be covered by our guarantee.
Handling and storage precautions
- Keep out of reach of children. If swallowed, seek medical advice immediately.
- When using the card with SD compatible equipment, make sure to insert and remove together
with the Adapter as one. Do not remove the card while the Adapter is in equipment. Misuse can
cause malfunction or damage the equipment or data.
- This card is formatted to the miniSD™ Card standard. If reformatting is ever necessary, format it
using SD compatible equipment or SD formatting software. Formatting the card with any other software will make the card nonstandard and cause problems with compatibility and performance.
- After removing the card and the Adapter from equipment, immediately store them in its case.
When storing the card, insert into the Adapter.
- Do not disassemble or remodel.
- Do not impact, bend, drop, or wet.
- Do not touch the metal terminals with your hands or metal objects.
- Do not allow dust, garbage, etc. to get in the Adapter’s slot.
- Do not attach other labels or stickers.
- Do not use or store in locations that may be affected by static electricity or electric noise.
- Do not user or store in locations directly exposed to sunlight, a heat vent, or a heating appliance.
- Do not use or store in humid or dusty locations or in locations exposed to corrosive gases.
Protecting your data
- When inserting the card into the Adapter, we advise you switch the write-protect
switch to LOCK (switch down) to prevent accidental loss of data. Unlock
(switch up) when you want to record or edit the card again.
- Use an oil-based felt pen to write on the card or the Adapter. Do not use pencils or ballpoint
pens as these can damage the card, the Adapter or data on the card. Take care to keep the
metal terminals free from ink.
- While data is being read or written, do not remove the card or turn off any equipment using
the card. Do not remove the batteries from battery-operated equipment. These actions can
cause data to be destroyed.
- Make backup copies of your data wherever possible.
84- miniSD™ Card
How to insert/extract your miniSD™ Card
Inserting your miniSD™ Card in
your phone: golden contacts Up.
Extracting your miniSD™ Card:
The miniSD™ Card must NOT be inserted
with the arrow symbol and miniSD™
brand name Up.
Inserting your miniSD™ Card in the
Adapter:
The miniSD™ Card must be formatted in your phone before its first use (please see "How to
configure your miniSD™ Card", page 86). If the formatting is done via another device (e.g. a
PC) you may not be able to use your miniSD™ Card on your M900.
How to access the miniSD™ Card contents
You can access the files that are stored on your miniSD™ Card via the sub-folders of the Fun
& Media box application (Pictures, Melodies, Videos, Speech notes, Others).
To view the files that are stored on a miniSD™ Card, please follow the standard process described for each of the corresponding sub-folders.
The miniSD™ Card item is only available in the Fun & Media box sub-folders if it is inserted in the phone.
To access pictures
See "To access images stored on your miniSD™ Card", page 71
To access melodies
See "To access melodies on your miniSD™ Card", page 73
To access videos
See "To access videos stored on your miniSD™ Card", page 75
To access music
See "To access music on your miniSD™ Card", page 77
85- miniSD™ Card
To access speech notes
See "To access speech notes stored on your miniSD™ Card", page 80
To access other files
See "To access other files stored on your miniSD™ Card", page 85
1. When using your miniSD™ Card with your PC, you can access a folder list corresponding to the Fun &
Media box sub-folders (Pictures, Melodies, Videos, Music, Speech notes, Others). We advise you put each
file in the corresponding folder otherwise it may not be read by the phone.
2. Some files you created on your miniSD™ Card via other devices may not be accessible by the phone.
3. You are not allowed to transfer or to copy protected files from your phone to your miniSD™ Card or other
devices.
4. The miniSD™ Card content is not accessible if the battery level is too low (’’Not allowed: battery too low’’
appears) and if the storage space is full (’’Not enough space’’)
How to configure your miniSD™ Card
The miniSD™ Card must be formatted in your phone before its first use
1
2
Insert the miniSD™ Card in the phone.
The ’Format card’ screen is displayed. Select Yes to format your miniSD™ Card. If you
select No, your miniSD™ Card is not formatted and cannot be used with your phone.
1. The first time you use your miniSD™ Card, do not format it via another device (e.g. your PC).
2. Formatting your miniSD™ Card deletes all the files on it.
3. Removing your miniSD™ Card during the formatting process can damage it.
You can also format your miniSD™ Card via the Settings menu. Formatting your miniSD™
Card deletes all the files on it. Do not forget to back up or transfer your files on your phone internal memory or on another device before going over the formatting process.
1
2
3
4
5
Insert the miniSD™ Card in the phone.
From the standby display, press the [Menu/T9] key. Select Settings.
Select Memory card.
Select Format card.
Select Yes then press OK to launch the miniSD™ Card formatting. An information screen is
displayed during the process.
Removing your miniSD™ Card during the formatting process could damage it.
Storage used
To check the remaining storage space on a miniSD™ Card:
1
2
4
5
Insert the miniSD™ Card.
From the standby display, press the [Menu/T9] key. Select Fun & Mediabox.
Select Storage used. The total phone memory used is displayed (all file types).
Use the [Up] and [Down] arrow keys to scroll to the required information type (Memory
card).
85- miniSD™ Card
CALENDAR
he availability of this menu is network dependent. If your SIM card does not
contain an access to the Network services the Calendar menu is accessible
from the Menu icons.
Please see "Calendar", page 16 for full details.
T
NETWORK SERVICES
he availability of this menu is network dependent (it may not be available or
be named Network services, Network,...).
Your network operator may provide value added services, information and contact
phone numbers. These services and phone numbers are stored in your SIM card
and appear on the phone menu as they are accessible from the Network serv.
menu. Please contact your service provider for further details.
Some operators may provide up to two services on the same SIM card. The displayed sub-menus in the Network serv. menu may then be named Applications, Services or Information.
Three kinds of services can be registered in this menu:
T
SIM application tool kit
An automatic way to provide services related to your network. These services are SIM card
dependent.
SND numbers stored in the SIM card
Up to 32 numbers may be stored in the SIM. These numbers cannot be modified or deleted.
Information numbers
A list or a menu allowing calls to network or information services offered by the network.
87- Calendar/Network services
WAP™
Your phone allows Wap™(Wireless Application Protocol) connections to
access operator and/or Wap™ provided services (e.g. news, sports, weather,
travel buying, etc.).
To get a Wap™ connection please make sure:
- your SIM card bears a Data subscription
- all the necessary parameters are stored into the phone. These parameters
may have been set by your operator. If not you have to enter them manually.
Please contact your service provider to check these elements and get the detailed list of parameters to be entered.
Storing the connection settings
The current date and time must be set before you enter any Wap™ connection setting.
The profile list can contain up to 10 Wap™ profiles. A profile is a list of parameters that allow
Wap™ connections.
To enter and store the profile details
You can only register profile details via the standard mode if you have previously registered profiles
in the Connection manager menu (see "Connection manager", page 99):
1
2
3
4
5
6
7
8
9
Press the [Menu/T9] key. Select Wap.
Select Settings.
Select Wap profiles.
Choose an empty profile ([...]) by selecting OK.
Enter the profile name and select OK.
Select Home page. Select List to select one of the available home page addresses or the
http:// and https:// root addresses, or type in the url address.
Select Connection profiles. Enter the requested information (the GSM connection and
GPRS connection fields are linked to the Connection manager and thus allow to pick one
from the displayed list - see "Connection manager", page 101). Select Save to store the
data.
Select Gateway settings and type in the IP address.
Select Push parameters (please contact your service provider to get the information to be
entered). Your Wap profile is then stored.
1.All the requested parameters are obtainable from your network operator and/or Wap™ provider.
2. The phone number or access point name, the login and the password are to be stored in the Connection
Manager (see "Connection manager", page 101).
3. Access to the connection settings may depend on the pre-programmation of the settings. The connection
settings menu may not be available in some cases. These settings may be 'Locked' and not be user programmable.
4. You can request the activation of the security feature from the profiles list (Advanced settings / Activate
security).
5. Your service provider may require to have the security context reset. Select Yes.
Starting a Wap™ session
If several Wap™ profiles are stored, you need to select one before launching a session:
1
2
3
4
Press the [Menu/T9] key. Select Wap.
Select Settings.
Select Wap profiles.
Scroll to the required profile and choose one by pressing OK (Selected is displayed).
If the profile was already selected, pressing OK directly leads to the profile contents.
88- Wap
To launch a Wap™ session from the idle menu:
1
2
Press the [Menu/T9] key. Select Wap.
Select Home page.
The Wap™ connection is then launched and the list of the available site services is displayed
once the page was downloaded.
If the activated Wap™ profile is not correctly set or if your subscription does not allow you to
reach the selected Wap™ site the Not available then Connection failure messages are
displayed.
To launch a Wap™ session from the standby screen:
1
2
Press and hold the OK key.
The Wap™ connection is launched and the list of the available site services is displayed
once the page is downloaded.
If the activated Wap™ profile is not correctly set or if your subscription does not allow you to
reach the selected Wap™ site the Not available then Connection failure messages are
displayed.
Once connected the Wap™ browser is displayed. The icon at the top of the display indicates
a GSM connection. The
icon is shown if your phone is connected to a GPRS network during
the Wap™ session.
During a WAP™ session, if a page contains more information than it can be displayed in the application part, a
scroll bar is displayed on the right part of the screen.
Getting to the options menu while online.
In the absence of Options while online pressing the call key during a live connection shows the
following options menu:
ITEM
ACTION
Back
Reload
Save...
Home page
Bookmarks
To go back to the previous page.
To reload the current Wap™ page.
To access the Save page, Save as bookmark, Attachments sub-menus
To go to and reload the home page.
To provide immediate access to the bookmarks. You can add a new
bookmark or select an existing bookmark.
To go to another Wap™ site.
To access the list of the saved pages.
To access the Push inbox.
Same as when offline.
To access the statistics screen of the Wap features
To disconnect the browser from the network. However the browser
remains active locally with the current page displayed.
To disconnect from the network, close the browser and get back to
the Wap menu.
Go to site...
Saved pages
Push inbox
Settings
Storage used
Disconnect
Close session
The availability of these options is operator dependent. It may also depend on the contents of the displayed page.
Ending the online connection
To end the Wap™ connection:
1
To disconnect press the end key or press Options and select Disconnect.
To close the session:
1
Press End or press Options and select Close session. Connection to the Wap™ server is
then ended.
To disconnect, then close the session:
1
Press the end key twice.
89- Wap
Personalising your connection settings
The following user settings are available and enable to optimise the phone behaviour during
Wap™ connection
1
2
3
Press the [Menu/T9] key. Select Wap.
Select Settings.
A list allows to select different options:
OPTION
ACTION
Wap profiles
To enter and register profile details.
To select GSM or GPRS as a default bearer when defining mixed based
(GSM + GPRS) profiles. If an error is detected the other bearer is then
proposed and may be used ('Use alternate connection mode?' is displayed).
To configure the browser and allow it to display the pages in large or normal
fonts, to allow or forbid pictures download and script execution in Wap™
pages, to accept or forbid cookies.
See "Receiving push messages", page 91.
Preferred
bearer
My
preferences
Push
preferences
The Preferred bearer sub-menu may not be available on your phone (operator dependent feature).
During page browsing, security can be activated (on a https link only). This lets you continue
local browsing (via the cards in the memory). When a connection to the network is needed
again, a secured connection is requested to the same profile.
When the secured connection is established, the
icon at the top of the display indicates a
circuit connection in secure mode. The
icon is shown if your phone is connected to a GPRS
network during the Wap™ session in secure mode.
When activating the secured mode the mobile and the server undergo exchanging certificates. You may then
be asked to accept this exchange.
Creating bookmarks
Bookmarks provide direct links to determined Wap™ pages. You can create and store maximum
20 bookmarks in your phone.
There are two ways of registering bookmarks:
Directly from the standby display,
1
2
3
Press the [Menu/T9] key. Select Wap.
Select Bookmarks. The list of bookmarks is displayed in alphabetical order.
Select an empty entry ([...]). Select and enter the requested information in the following
fields:
ITEM
ACTION
Alias
Address
Name you want to give to your bookmark
Home page address (if known)
4
Select Save to store the data.
During a Wap™ session whilst viewing a page:
1
2
Press the call key.
Select Bookmarks, then follow the above procedure.
Bookmarks can be Edited or Deleted from the Bookmarks item under the Wap™ menu options whilst offline or
online.
Using bookmarks
Bookmarks can be used:
- directly from the standby display:
1
2
3
Press the [Menu/T9] key. Select Wap.
Select Bookmarks.
Select the bookmark name you require to directly connect to the corresponding Wap™
site.
90- Wap
- whilst you are browsing the Wap™:
1
2
3
Press the call key to display the options menu.
Select Bookmarks.
Select one of the bookmark names to access the required Wap™ site.
1. Selecting OK directly tries to reach the bookmarked page.
2. On an existing Bookmark entry the options Go to Bookmark, View, Delete, Send and Export all are available.
Go to site
The following sub-menu allows easy access to Wap™ sites:
1
2
3
Press the [Menu/T9] key. Select Wap.
Select Go to site....
A list allows to freely enter or select Wap™ sites addresses:
OPTION
ACTION
Last page
Site history
New address
New Bango
address
To connect to the latest page accessed with the Wap browser.
To directly go to one of the pages you have already been to.
To enter a Wap™ site address you want to reach.
To enter a Bango address site.
1. The New Bango address option may not be available on your phone. Please check with your service provider.
2. Addresses are not stored in New address and New Bango address. They must be entered each time these
features are used.
Saved pages
You an access a list of pages you have previously stored:
1
2
3
Press the [Menu/T9] key. Select Wap.
Select Saved pages.
A list allows to freely enter or select Wap™ sites addresses:
The items are ordered by storage date.
The following Options menu is available:
OPTIONS
ACTION
View
Delete
Delete all
Rename
To view the selected saved page.
To delete the selected saved page.
To delete all the saved pages.
To change the name of the selected saved page.
Receiving push messages
A push message is a message sent via a service/Wap™ provider. Push messages can bear
promotional or general information (e.g.: weather forecast). To view the related information you
need to connect to the Wap™ server.
The push messages are displayed on the phone and/or stored in the Push Inbox, according to
the Push settings. At the end of the transmission the push reception session is ended.
The Push Inbox allows to consult and delete the stored messages but also to launch the connection
to related server to retrieve the information.
When the Push Inbox contains new message(s), an information message is displayed in the
standby display with a direct access to the inbox.
91- Wap
To set the push reception parameters:
1
2
3
Press the [Menu/T9] key. Select Wap.
Select Settings.
Select Push preferences and set the different parameters :
1/ Accept push info:
Never: to forbid push messages reception.
Current profile: to allow only push messages from the current Wap™ profile.
All profiles: only allows push messages from the configured Wap™ profiles.
Always: no filtering, allows reception of all push messages.
2/ Push quiet mode:
on/off: push message information displayed/not displayed on push message reception.
3/ Accept provisioning:
see information above about Accept push info. To allow, forbid or filter messages bearing
connection profiles to connect to Wap™ sites.
To consult a push message in the Push inbox:
1
2
3
Press the [Menu/T9] key. Select Wap.
Select Push inbox. Summaries of all push messages are displayed according to their
reception date and time.
Press Options then select Read text to display the selected message text in full screen
mode.
The following options may also be available:
OPTIONS
PURPOSE
Read text
Summary
Preview
To provide access to the message text (possibly on several pages)
To return to the summary display
To connect to the service but keep the message in the inbox allowing another
access to the same service later
To connect to the service and delete the message from the inbox when the
connection to the service is made.
To delete the item
To delete all inbox push messages
To provide the expiry date for this item (if available)
Retrieve
Delete
Delete all
Details
This options list may change according to the push message received.
Storage used
1
2
Press the [Menu/T9] key. Select Internet.
Select Storage used to get detailed information on Site history, Saved pages, Push inbox
and Cache.
Melodies download
See "Melody download", page 74 for information on melody download from Wap™ sites.
Advanced settings on Wap™ profiles
The advanced settings are used to support specific configurations and improved services available
on certain Wap™ gateways. This menu is operator dependent and may not be available on your
phone. These parameters are displayed as Wap™ profile items.
To get to the Advanced settings menu:
1
2
3
4
5
6
Press the [Menu/T9] key. Select Wap.
Select Settings.
Select Wap profiles.
Select Options.
Select View.
Select Advanced settings. The following options are available:
92- Wap
OPTION
DESCRIPTION
Send characteristics
Activate security
Use SAR
To allow the sending of the phone characteristics to the remote server.
To activate or deactivate the security level for the current profile.
To activate or deactivate the SAR (Segmentation And Reassembly)
protocol (to enable the download of large data).
To display the possible encoding versions. Select 1.1, 1.2, 1.3 or 1.4.
Encoding
version
Normal port
Secure port
Use
download fun
Use range
To edit the port address for non secure connections.
To edit the port address for secure connections.
To activate or deactivate the use of the OpenwaveTM solution (to manage
the download of large data).
To activate or deactivate the range service.
The availability and contents of this menu is operator dependent.
93- Wap
SETTINGS
This menu allows you to set up your mobile phone as per your own preference.
Tones
Alert mode
You can set the ring, alert and alarm tone types via the Mode menu.
If you select the 'Vibrate' or 'Vibrate then ring' option, the vibrating option replaces all the alert and alarm tones.
To modify the alert mode:
1
2
3
4
Press the [Menu/T9] key. Select Settings.
Select Tones.
Select Mode.
Select one of the available settings (Ring, Silent, Vibrate, Vibrate & ring or Vibrate then
ring) and press OK to validate.
1
2
From the standby display, press the [Up] arrow key.
Select one of the available settings (Ring, Silent, Vibrate, Vibrate & ring or Vibrate then
ring) and press OK to validate.
or:
1. If the Alert mode is set to Silent, the icon is displayed on the Standby display.
2. If the Alert mode is set to Vibrate, Vibrate & ring or Vibrate then ring, the
icon is displayed on the
Standby display.
3. When the phone is connected to either the Desk Top Charger, HF kit, CLA or AC adaptor, the vibrator
mode selection is temporarily inhibited and the phone rings instead of vibrating.
Ringtone selection
You can select a melody, a speech note or a music file from the available ring tones stored in
the phone.
1
2
3
4
5
6
Press the [Menu/T9] key. Select Settings.
Select Tones.
Select Ringtones.
Select Incoming call, Incoming call L2, Alarm (then select Melodies, Music, Speech notes)
or Welcome melody (On switching on the phone, a welcome melody plays before the Standby
display is displayed) or Goodbye melody (on switching off the phone, a Goodbye melody
plays).
Scroll up or down to listen to the different ringtones. Select one by pressing OK.
Select Save to store your settings.
1. When scrolling up or down, wait for a few seconds for the selected melody to be played (except when on
Silent mode).
2. The ‘No sound’ item may be selected to deactivate the Welcome and Goodbye melodies.
3. You can set a ringtone for each of your phone book cards (please see "Setting a melody, a music or a
speech note as a ringtone", page 47). This ringtone is played on receipt of an incoming call.
4. You can only choose a melody, a speech note or a music while selecting a ringtone for your incoming call,
incoming call L2 or alarm.
Volume adjustments
The ring tone, key tones, conversation and alarm tones (alarm clock, diary alarm and low battery alarm) audio levels can all be individually set via the Settings menu:.
1
2
Press the [Menu/T9] key. Select Settings.
Select Tones .
94- Settings
3
4
5
6
7
Select Volume.
Select Ring, Keys, Conversation or Alarm.
Scroll up or down to adjust the settings. You can also use the numeric keys
to set the required audio level: pressing
sets the volume to 2, pressing
or
sets the volume to 6 or 7, pressing
sets the volume to the minimum
value (1 for speech and 0 for all others).
Press OK to validate the setting.
Select Save to store your setting.
1. If the ringtone volume level is set to 0, the icon is displayed on the Standby display.
2. Setting the key tones to 0 deactivates the key tones.
3. You can set the conversation volume by using the [Up]
side key (to increase the sound volume level) or
the [Down]
side key (to decrease the sound volume level).
Ramping
When activated, this feature gradually increases the incoming ringtone to the maximum volume
level if the call is not answered after the first ring.
1
2
3
4
5
6
Press the [Menu/T9] key. Select Settings.
Select Tones.
Select Volume.
Select Ramping.
Select On.
Select Save to store your setting.
Display
Main screen
You can set a pre-embedded picture (see " Fun & media box", page 69).To select a background
image for your Main screen:
1
2
3
4
5
Press the [Menu/T9] key. Select Settings.
Select Display.
Select Main screen.
Select Pictures (see "Pictures", page 69) to select one the stored images or select one of
the five available background images.
Select Save to store your setting.
1. The Urban theme changes twice a day: a night screen is set at 7 p.m. and a day screen at 7 a.m.
2. The Meridian theme displays the origin and the secondary clocks.
3.You can also set your Main screen image from the Pictures menu (see "Setting a still or animated image as
a standby display (for the Main screen or the External screen), as a Welcome screen or as a Goodbye screen
from the Pictures folder", page 71).
4. The above mentioned background themes may not all be available on your phone.
External screen
You can set a still image to personalise your phone External screen.
To select a background image for your External screen:
1
2
3
4
5
Press the [Menu/T9] key. Select Settings.
Select Display.
Select External screen.
Select Default to set the default image as standby screen for your External screen or select
Pictures (see "Pictures", page 69) to select one of the stored pictures.
Select Save to store your setting.
You can also set your External screen image from the Pictures menu (see "Setting a still or animated image as
a standby display (for the Main screen or the External screen), as a Welcome screen or as a Goodbye screen
from the Pictures folder", page 71).
Welcome screen
Upon switching on your phone, a Welcome screen is displayed prior to the Standby display. This
screen is a default one but you can customize it by selecting any of the Pictures folder images
95- Settings
(see "Pictures", page 69).
1
2
3
4
5
Press the [Menu/T9] key. Select Settings.
Select Display.
Select Welcome screen.
Select Default to set the default image as standby screen for your Welcome screen or select
Pictures (see "Pictures", page 69) to select one of the stored pictures .
Select Save to store your setting.
You can also set the Welcome screen from the Pictures menu (see "Setting a still or animated image as a
standby display (for the Main screen or the External screen), as a Welcome screen or as a Goodbye screen
from the Pictures folder", page 71).
Goodbye screen
Upon switching off your phone, a Goodbye screen is displayed. You can customize it by
selecting any of the Pictures folder images (see "Pictures" on page 69).
1
2
3
4
5
Press the [Menu/T9] key. Select Settings.
Select Display.
Select Goodbye screen.
Select Default to set the default image as standby screen for your Goodbye screen or select
Pictures (see "Pictures", page 69) to select one of the stored pictures.
Select Save to store your setting.
You can also set the Goodbye screen from the Pictures menu (see "Setting a still or animated image as a
standby display (for the Main screen or the External screen), as a Welcome screen or as a Goodbye screen
from the Pictures folder", page 71).
Backlight
To adjust the backlight for the Main or the External screens:
1
2
3
4
5
Press the [Menu/T9] key. Select Settings.
Select Display.
Select Backlight.
Adjust the backlight for the Main screen or the External screen with the [Up] or [Down] arrow
keys (select a value from 1 to 4) and select OK.
Select Save to store the setting.
Contrast
You can select the contrast level for the Main screen and for the External screen:
1
2
3
4
5
Press the [Menu/T9] key. Select Settings.
Select Display.
Select Contrast (Main) or Contrast (External) according to the screen you want to adjust
the contrast on.
Adjust the contrast with the [Up] or [Down] arrow keys (-3 to +3) and select OK.
Select Save to store the setting.
Light
You can activate or desactivate the light on the External screen (please see "Light status", page
11):
1
2
3
4
5
Press the [Menu/T9] key. Select Settings.
Select Display.
Select Light (External).
Select On or Off.
Select Save to store the setting.
Keypad
Keypad lock
When the keypad lock is activated, this prevents the accidental operation of the keys. The key
tones are muted.
The keypad lock is suspended when an incoming call is received and resumed once the call is
96- Settings
over. Emergency calls (112, 911 or other official emergency number) can however be made. If
a key is pressed, a reminder message is displayed.
To activate and deactivate the keypad lock:
1
2
3
4
Press the [Menu/T9] key. Select Settings.
Select Keypad.
Select Keypad lock.
To unlock the keypad, press Unlock then .
1
2
From the Standby display, press and hold
to activate the keypad lock.
Press and hold
to de-activate the keypad lock.
or:
Any key answer
This feature allows you to answer a call by pressing any key (except from the Off, No ring and
Side keys).
1
2
3
Press the [Menu/T9] key. Select Settings.
Select Keypad.
Select Any key answer and select On.
Softkey functions
This feature allows to change the right and left softkeys functions to get a shorten access to the
feature you want.
Via the idle menu:
1
2
3
4
Press the [Menu/T9] key. Select Settings .
Select Keypad
Select Softkeys functions and select left softkey or right softkey.
The list of functions is displayed. Scroll up or down to the required function and press OK.
Via the standby screen:
1
2
Press and hold the left softkey or the right softkey.
The list of functions is displayed. Scroll up or down to the required function and press OK.
Speed dial
Phone book numbers can be assigned to keys
to . The
key cannot be assigned to a
Phone book number as it is already assigned by default to the Voice Mail number (see "Calling
the voice mail centre to check your messages", page 29).
Numbers stored in both the SIM card and the phone (except fixed dialling numbers) can be
selected.
To assign Phone book numbers to the speed dialling keys:
1
2
3
4
5
Press the [Menu/T9] key. Select Settings.
Select Keypad.
Select Speed dial.
The Key number and the attached name (if any) are displayed. Select Names (or Options
then Names if a number has already been attached to the key) to select a name from the
names list.
Select OK to validate.
If a number which has been assigned to a speed dial key is deleted from the Phone book, the corresponding
number is automatically deleted from the speed dial key.
Phone settings
Language selection
You can change the language on your phone:
1
2
3
4
Press the [Menu/T9] key. Select Settings.
Select Phone settings.
Select Language.
Select a language from the list displayed and press OK to validate.
97- Settings
Edit mode
You can change the Edition mode on your phone:
1
2
3
4
Press the [Menu/T9] key. Select Settings.
Select Phone settings.
Select Edit mode.
Select Multilingual or Standard.
Auto features
Auto-answer
This feature is only operational when the phone is connected to a headset or a car kit. The
phone answers the call automatically after about 5 seconds.
1
2
3
4
5
Press the [Menu/T9] key. Select Settings.
Select Phone settings.
Select Auto features.
Select Auto-answer and select On.
Select Save to store your setting.
This feature is inhibited if the silent mode is activated or if the ringtone is set to 0.
Auto-retry
This feature allows the phone to redial a number automatically if call has failed due to an engaged
line or an unavailable signal from the network. The number will be re-dialled a maximum of 10
times until connection is established.
1
2
3
4
5
Press the [Menu/T9] key. Select Settings.
Select Phone settings.
Select Auto features.
Select Auto-retry and select On.
Select Save to store your setting.
When activated, Retrying and a countdown timer are displayed prior to each new attempt. An
auto-retry warning tone beeps each time a new call attempt is made.
Selecting Exit or pressing any key during the retry process cancels the operation.
Auto-switch-on/off
This feature allows the phone to switch on or off automatically at a pre-determined time.
1
2
3
4
5
6
Press the [Menu/T9] key. Select Settings.
Select Phone settings.
Select Auto features.
Select Auto-switch-on or Auto-switch-off and select On to activate the feature.
Enter the time you want your phone to switch on and/or to switch off and press OK.
Select Save to store your setting.
If the phone is already on at automatic switch-on time, it remains on.
When the phone is about to automatically switch off, a warning message and a countdown timer
are displayed. Selecting Exit cancels the switch off process.
If the phone is already off at switch-off time, it remains off.
If a call is in progress at switch-off time, the switch-off process is postponed until the call has ended.
Caution - Remember to turn off the Auto switch-on feature when boarding an aircraft.
See "General safety", page 6.
Active flip
This feature allows you to answer/end a call automatically on opening/closing the phone.
1
2
3
4
5
Press the [Menu/T9] key. Select Settings.
Select Phone settings.
Select Auto features
Select Active flip and select On to activate the feature.
Select Save to store your setting.
98- Settings
Time & date
This feature allows you to set the phone time according to the world time zone map, based on
Greenwich Mean Time (Origin clock). A Secondary clock is also available.
This feature is useful for the Diary. To import or export calendar cards, events and tasks, schedules must be set according to Time zones.
Both clocks are displayed on the same screen. The date and time and the city name are displayed for both clocks.
Clock setting
To set the clocks:
1
2
3
4
5
6
7
Press the [Menu/T9] key. Select Settings.
Select Phone settings.
Select Time & date.
Select the Origin clock or select Options, then choose Edit origin. Scroll
through the panels and fill in the required information.
Select Save to store the data.
Select the Secondary clock or select Options, then choose Edit secondary. Scroll through the panels and enter the required information.
Select Save to store the data.
Select Options to get to the following features:
OPTIONS
ACTION
Edit origin
To edit the origin clock panel in order to modify its contents.
Edit secondary To edit the secondary clock panel in order to modify its contents.
Swap clocks
To swap the Origin clock and the Secondary clock. This feature is useful
when travelling: the secondary clock becomes the origin/mobile clock and
the origin clock becomes the secondary one.
Time format
To select a time format (12Hrs or 24Hrs).
Default settings
You can reset your phone and return to your phone default settings via the Settings menu.
This has no effect on the Phone book entries or the phone lock code.
1
2
3
4
Press the [Menu/T9] key. Select Settings.
Select Phone settings
Select Default settings.
Select Yes (The «Set default ?» message is displayed)
Connection manager
The Connection manager service manages and centralises circuit and packet connection profiles
(see "Wap™", page 88) for online applications.
Connection profiles
Viewing a profile
1
2
3
4
Press the [Menu/T9] key. Select Settings.
Select Connection manager.
Select Connection profiles.
Scroll down to the required profile. Press OK or Option and View to display the profile.
The Option menu allows to View and Delete the profile.
Creating a connection profile
1
2
3
4
5
Press the [Menu/T9] key. Select Settings .
Select Connection manager.
Select Connection profiles.
Choose an empty profile ([...]) and select OK.
Choose GPRS connection or GSM connection and select OK.
99- Settings
6
Fill in the requested information (contact your service provider to get all necessary parameters) and select Save to store the entered data.
Operation mode
This network dependent setting allows phone operations to be either Standard or Modem
type.
Standard mode
The phone tries to reach a GPRS networks. If the phone succeeds attaching a GPRS network,
is displayed on standby mode. The phone can then send and receive voice calls and packet
data calls.
To set the mode of operations to Standard:
1
2
3
Press the [Menu/T9] key. Select Settings.
Select Connection manager.
Select Operation mode.
Select Standard.
Modem mode
The phone tries to reach a GPRS network. It can only send and receive GPRS data calls; voice
calls are then barred. This behaviour is the same whatever the network capabilities.
However if the GPRS services are lost, the phone automatically returns to the Standard operation
mode.
To set the operation mode to Modem:
1
2
3
4
Press the [Menu/T9] key. Select Settings .
Select Connection manager.
Select Operation mode.
Select Modem.
GSM services
Call diverting
This Network dependent service allows you to divert incoming calls (voice, fax or data calls) to
another number
To divert a call:
1
2
3
Press the [Menu/T9] key. Select Settings.
Select GSM Services.
Select Call diverting. The following sub-menu is displayed (the contents of this menu may
vary according to your service provider).
DIVERT OPTIONS
ACTION
Always
When not
reachable
On no reply
When busy
All conditions
Cancel all
All FAX calls
All DATA calls
To divert all incoming voice calls.
To divert all voice calls when the phone cannot be reached (out of service).
4
5
6
To divert all voice calls when the call is not answered.
To divert all voice calls when the line is engaged.
To divert all voice calls when Not Reachable, No Reply and When Busy.
To cancel all diverting options.
To divert incoming fax calls unconditionally.
To divert incoming data calls unconditionally.
Select one of these options and select OK.
Select Activate.
Select Voice Mail (if you want the calls to be diverted to your voice mailbox), Names (select
one of the Phone book entries) or Number (Enter the number to which the calls are to be
diverted and select OK. A validation message containing the selected number is displayed).
1. If the 'On no reply' option is selected, please enter the time limit (5, 15 or 30 seconds; this also depends on
your network) after which the feature will operate.
2. Call diverting must to be set for both Line1 and Line2. Only the selected line is affected by the call divert.
100- Settings
To check the call divert status or deactivate it:
1
2
3
4
Press the [Menu/T9] key. Select Settings.
Select GSM Services.
Select the call diverting type to be checked or cancelled.
Select Status or Cancel.
To cancel all call diverts,
1
2
3
4
Press the [Menu/T9] key. Select Settings.
Select GSM Services.
Select Call diverting.
Select Cancel all.
1. This action cancels all call diverts (voice, faxes and data calls) for the current line.
2. To cancel call diverts for the other line, you must select this line first (menu Calls & Times - Line selection).
Call waiting
This network dependent feature allows you to receive a new call while a call is already in
progress. To activate the call waiting feature:
1
2
3
4
Press the [Menu/T9] key. Select Settings.
Select GSM Services.
Select Call waiting.
Select Activate. Activated or Check your request is then displayed.
You can also cancel or check the service status.
To put a call on hold and switch from Call 1 to Call 2:
1
2
Whilst a call is in progress, a beep sounds to indicate a second incoming call.
Select Replace to take Call 2 and end Call 1, select Reject to refuse Call 2 or press the Call/
[Send] key to put Call 1 on hold and take Call 2.
Press the [End/Off] key to end Call 1 and press the [Call/Send] key to take Call 2.
Select Options then select Swap to get back to Call 1 and put Call 2 on hold.
When two calls are managed on the device the following Options menu is available:
OPTIONS
DESCRIPTION
Speaker On/Off To activate/deactivate the hands free mode.
Auto-DTMF
To type a new phone number and add this new correspondent to the
conference-call. If the Auto-DTMF option is deactivated, you cannot type in
a new phone number.
Swap
To switch from Call 1 to Call 2.
Join
To set up a conference-call.
Mute/Unmute
To mute/unmute the microphone.
End held
To end the held call.
End active
To end the active call.
End all
To end both calls.
Record
To record the call up to 11min.
To set up a conference-call
You can set up a conference-call with up to 5 participants. This option is network/subscription
dependent.
1
Whilst two calls are in progress and a new call is received, select Options then Join or press
then press the [Call/Send] key to set up the conference-call. Repeat the action each time
a new call is received.
During the conference-call, the following Options menu is available:
OPTIONS
DESCRIPTION
Speaker On/Off To activate/deactivate the hands free mode.
Auto-DTMF
To type a new phone number and add this new correspondent to the
conference-call. If the Auto-DTMF option is deactivated, you cannot type in
a new phone number.
101- Settings
Private with
Hold
Retrieve
Mute/Unmute
End one
End all
Record
To have a private conversation with one of the participants. During a private
conversation, the conference-call is put on hold.
To put the conference-call on hold.
To retrieve the conference-call if it is put on hold.
To mute/unmute the microphone.
To end one call.
To end the conference-call.
To record the conference-call up to 11min.
You can set up and receive a new call during the conference-call. In these cases the conference-call is put on
hold.
In compliance with European regulations, you are obliged to inform your correspondents
before recording a phone conversation.
To end a conference-call:
1
Press the [On/Off] key or select Options then End all to end the conference-call.
Sending my ID: status
You can disable the sending of your own number on a call by call basis by adding #31# before
the number you are dialling. You can also ask your service operator to hide your mobile phone
number by default. Once hidden by your operator, you can show your number, on a call by call
basis, by entering *31# before the number you are calling.
To check the Sending my ID status:
1
2
3
4
Press the [Menu/T9] key. Select Settings.
Select GSM Services.
Select Sending my ID.
Select Status. The request is launched and an information message displays the Sending
my ID status.
Please contact your service provider for more information.
Caller line identity - showing/hiding your mobile number (network dependent)
Most networks have Caller Line Identity feature (CLI). This feature allows the phone number or
the identity of the caller to be displayed on incoming calls.
Standard network setting
To reset the standard network setting and send your mobile ID:
1
2
3
4
5
Press the [Menu/T9] key. Select Settings.
Select GSM Services.
Select Sending my ID.
Select My settings.
Select Preset. The phone resets and reverts to its original network setting.
Hiding or showing your number
1
2
3
4
5
Press the [Menu/T9] key. Select Settings.
Select GSM Services.
Select Sending my ID.
Select My settings.
Select Hide my ID or Show my ID.
Please contact your service provider for more information.
Receiving caller ID
Most networks have the Caller Line Identity feature (CLI). This feature allows the phone number
or the identity of the caller to be displayed on incoming calls.
You can check the availability of this feature on your network or subscription.
1
2
Press the [Menu/T9] key. Select Settings.
Select GSM Services.
102- Settings
3
Select Receiving caller ID.
The network then either returns Presentation available or Presentation unavailable information.
Network automatic search
When the phone is on, it automatically searches the last network to which it was registered
(usually the home network). If it is not available, the phone automatically searches and selects
one of the networks registered in the preferred network list (located in the SIM card).
Editing the preferred list
Your phone contains a list of networks which can be selected (e.g.: to suit your travel arrangements). You can also transfer items from this list to the preferred networks list.
The order and names of the networks in the preferred networks list can be edited and amended.
1
2
3
4
5
OPTION
Press the [Menu/T9] key. Select Settings.
Select GSM Services.
Select Network.
Select Preferred list. A list of networks is displayed.
Use the up and down arrows to select the required network. Press OK to select one of the
following Options if you want to amend the list:
DESCRIPTION
Modify by list
To display the list of all networks stored in the phone.
Modify by code To edit or enter the identification operator number if you have the
information.
Delete
To delete an entry
Your SIM card may contain a forbidden list of networks which cannot be used. To view this or
show your home network:
1
2
3
4
Press the [Menu/T9] key. Select Settings.
Select GSM Services.
Select Network.
Select either Forbidden to view the list of forbidden networks, or select Home network to
view the name of your usual network.
Selecting manual search
You may need to select a specific network (e.g. better coverage than your own in the current
location).
1
2
3
4
5
6
7
Press the [Menu/T9] key. Select Settings.
Select GSM Services.
Select Network.
Select Search.
Select Manual. The Scanning for networks... message is displayed.
Use the [Up] or [Down] arrow keys to select a network from the list.
Press OK to confirm your choice.
The Requesting... message is displayed, after which the phone will return to the standby
display.
1. You cannot select a network for manual change if it is on the forbidden list (even if it is still listed as a choice).
2. You cannot delete a network from the forbidden list. This list is automatically updated when the manual network
selection is performed.
3. If the Manual search has been selected before turning the phone off and if the manually selected network
cannot be found when the phone is next turned on, you must select another network manually for your phone
to lock on.
Selecting automatic search
To perform an automatic search from the preferred list, proceed as follows:
1
2
3
4
5
Press the [Menu/T9] key. Select Settings.
Select GSM Services.
Select Network.
Select Search.
Select Automatic.
103- Settings
Call barring
This network dependent service forbids certain outgoing or incoming call types. It requires a
call barring password.
To bar a call
1
2
3
4
5
Press the [Menu/T9] key. Select Settings.
Select GSM Services.
Select Call barring.
Select Outgoing calls (to bar All outgoing calls, International calls or International calls
excluding your Home network), Incoming calls (to bar All incoming calls or all incoming calls
while Roaming only), Cancel all (to cancel all barring conditions) or Change password.
Select Activate. Enter the password and press OK.
The network then confirms the selection.
To remove call barring or check its status
1
2
3
4
Press the [Menu/T9] key. Select Settings.
Select GSM Services.
Select Call barring.
Scroll up or down to select the barring type to be deactivated (Cancel) or checked and follow
the instructions displayed.
Call barring password
The call barring password is used to select the call barring levels. It is supplied via your service
provider.
To change the password:
1
2
3
4
Press the [Menu/T9] key. Select Settings.
Select GSM Services.
Select Call barring.
Select Change password.
First enter the former password then enter the new password twice. A Confirmation message
is displayed.
Security features
The security features described in this section protect your phone from unauthorised use.
When prompted, enter the code and press OK. Codes are displayed as asterisks (*).
Press the [Clear] key if you need to amend your entry.
Avoid using codes similar to emergency numbers such as 112 to prevent the accidental dialling of these numbers.
KEEP A RECORD OF YOUR CODES IN A SECURED PLACE.
PIN code
Your SIM card was provided with a 4 to 8 digit PIN code for protection against unauthorised
use. When enabled, the PIN code is required each time you turn your phone on. If an incorrect
PIN code is entered three times in succession, your SIM card will be blocked. The 8 digit PUK
code is then required to unblock your phone. Please contact your service provider for this code.
To activate the PIN protection:
1
2
3
Press the [Menu/T9] key. Select Settings.
Select Security.
Select PIN enable (if the code has been disabled) or PIN disable (if the code has been
enabled) and enter your PIN code.
To change the PIN code (PIN must first be enabled):
1
2
3
4
Press the [Menu/T9] key. Select Settings.
Select Security.
Select PIN change and follow the information displayed.
Press OK to validate your new PIN code.
PIN2 code
PIN2 code prevents unauthorised access to some of the phone features (e.g. activating/deac-
104- Settings
tivating FDN operations, modifying the FDN Phone book, setting calls costs to zero, modifying
the costs display features). This code can be changed but not be activated or deactivated.
Please contact your service provider for your PIN2 code. To change the PIN2 code:
1
2
3
4
Press the [Menu/T9] key. Select Settings.
Select Security.
Select PIN2 change and follow the information displayed.
Press OK to validate your new PIN2 code.
Summary of code/password entry chart
PASSWORD
LENGTH
NUMBER OF ATTEMPTS ALLOWED IF BLOCKED OR FORGOTTEN
PIN
PIN2
PUK
PUK2
Call barring
password
4-8 digits
4-8 digits
8 digits
8 digits
4 digits
3
3
10
10
Defined by service provider
Unblock with PUK code
Unblock with PUK2 code
Contact your service provider
Contact your service provider
Contact your service provider
Certificates
Certificates are used for network security exchange.
There are two types of certificates: the user’s certificate and the trusted certificate.
The user’s certificate is sent by the phone to the contacted WAP™ service. It is a proof of the
user’s identity.
The trusted certificate is sent by the contacted WAP™ site to the phone. It guarantees the
WAP™ site is authentic and you have the right certificate in your phone. If you do not have the
right certificate the site identity cannot be checked (certificates can then be downloaded from
a WAP™ page).
To display a certificate,
1
2
3
Press the [Menu/T9] key. Select Settings.
Select Security.
Select Certificates. Enter the 4 digit lock code (default code is 0000) and press OK. The list
of certificate subjects is displayed.
The detailed view is displayed and is made of:
- A header which informs about the certificate format and its storage location,
- The certificate subject,
- The certificate issuer,
- The certificate validity dates (start and end dates),
- The certificate fingerprint.
WIM manager
Using WIM (Wireless Identity Module) Manager allows secured access to paid services via the
WAP™ features.
A special WIM card is required to use this feature (please contact your service provider for more
information on the WIM card). It allows certificates (see definition above) and tickets to be provided to and from selling companies when undergoing a paid transaction.
To enter the WIM manager menu:
1
2
3
Press the [Menu/T9] key. Select Settings.
Select Security.
Select WIM Manager.
Select one of the list items:
- WIM code (PIN code available on the WIM card to change, create or delete a file) change/
unblock. If you enter 3 wrong WIM codes, ’WIM code blocked’ is displayed.Contact your service
provider to get the corresponding unblock code.
- Signature codes (list of the different signature codes). These codes depend on the service you
wish to use (contact your service provider for more information on the signature codes).
105- Settings
- Tickets. A ticket is a document emitted on purchasing as a proof of the transaction (receipt).
5 tickets can be stored in the phone memory (they are then deleted one after another).
To go over a transaction and use the security WIM system:
1
2
3
4
From the WAP™ page, when getting to a paid service, press OK.
A sum-up of the transaction is shown on the following page. Press OK to validate.
Enter the requested signature code (4 to 8 digits). A sum-up of the whole transaction (the
Ticket detail page) is then displayed and shows the transaction Date, Clear Text and Information.
Press OK to validate and save the ticket.
Tickets are tracks of transactions as they are emitted by the phone and not by the selling company. They cannot be used as a proof in case of legal problem.
To view tickets:
1
2
3
4
5
Press the [Menu/T9] key. Select Settings.
Select Security.
Select WIM Manager.
Select Tickets.
The list of available tickets is displayed: choose one and
select OK to view its contents.
Privacy
A lock code can be used to activate the Phone lock code at phone switch On or to forbid the
access to the Privacy menu and to the following features: Mail Inbox, Outbox and Draft foldrs,
MMS Inbox, Outbox and Draft folders, SMS Inbox, Outbox, Draft and SIM archive folders, Pictures, Videos and Speech notes folders.
The default lock code is 0000 (this code can be changed).
To lock a feature
1
2
3
Press the [Menu/T9] key. Select Settings then Privacy. Enter the lock code.
Select the requiered feature(s) and select On in each of them to activate the lock code protection.
Select Save to store your settings.
The lock code is required when next time you switch on your phone and when
entering any of the selected feature.
To unlock a feature
1
2
3
Press the [Menu/T9] key. Select Settings then Privacy. Enter the lock code.
Select the required feature(s) and select Off in each of them to deactivate the lock code
protection.
Select Save to store your settings.
You will not be prompted for lock code when you access these features.
To change the lock code
1
2
3
Press the [Menu/T9] key. Select Settings then Privacy. Enter the lock code.
Select Lock code change and follow the displayed instructions.
Select Save to store the new lock code.
miniSD™ Card
Please see "How to configure your miniSD™ Card", page 86.
106- Settings
APPENDIX
Glossary
EXPRESSION
MEANING
AC/DC charger
Active call
ALS
AoC
CB
CLI
DES
Diverting
DTC
DTMF
FDN
GSM
http
IN
IP
LCD
MMI
MMS
PIN/PIN2
PPP
PUK/PUK2
Alternating Current/Direct Current charger
The call currently in progress
Alternate Line (Line 2) Service
Advise of Charge - subscription service
Cell Broadcast
Caller Line Identity - displays caller’s telephone number
Data Encryption Standard
Diverts incoming calls to the phone to another number
Desk Top Charger
Dual Tone Multifrequency Tones
Fixed Dialling Number
Global System for Mobile communications
Hyper Text Transfer Protocol
Information Numbers of your operator
Internet Protocol
Liquid Crystal Display
Man Machine Interface
Multimedia Messaging Service
Personal Identification Number. Supplied by your network/service provider
Point to Point Protocol
PIN Unblocking Key. Used to unlock PIN and PIN2. Supplied by your network/
service provider
Quarter Quarter Video Graphics Array
The ability to use your telephone on networks other than your home network.
Service Dialling Number of your operator or service provider
Subscriber Identity Module. Supplied by your network/service provider
Short Message Service
Service Provider Name
Status Report - relates to SMS messages
When the phone is on but not receiving/making a call or menu navigating.
Uniform Resource Locator
Video Graphics Array
QQVGA
Roaming (Rm)
SDN
SIM
SMS
SPN
SR
Standby mode
URL
VGA
107- Appendix
Troubleshooting
PROBLEM
POSSIBLE CAUSE AND SOLUTION
Phone does not
switch on
No flashing
battery icon
whilst
charging
Short standby
and talk times
Check that the battery is fully charged and correctly connected to the phone.
There may be no mains supply. Try a different electrical socket.
The AC/DC charger may be faulty. Return to your dealer and try substitution with
another Mitsubishi Electric adaptor. If faulty, contact your dealer.
Cell broadcast is permanently on, using more battery power.
Phone is in a poor signal area and therefore always on full power.
Incorrect charging and discharging. Always charge and discharge your battery
fully.
The battery is wearing out. Replace the battery.
Impossible to dial Keypad lock is on ( appears). Press Unlock and
to turn the keypad lock off.
numbers
Impossible to
Check that at least one signal strength bar ( ) is displayed. Try a stronger signal
make or receive a strength area.
call
If no network name is displayed, check registration and area coverage with your
service/network provider and check that the SIM is correctly inserted.
Call barring option is on. Deactivate it (see page 106). Call cost limit is reached
(see page 44).
Stored telephone Fixed Dialled Number or Call Barring features are activated. Deactivate feature.
numbers cannot (see page 106).
be recalled
The mobile is on Display contrast is too low. Reset contrast (see page 98).
but nothing is
displayed.
Battery icon
May indicate a charge or battery problem. Disconnect the charger. Reconnect and
not flashing 1-2- try again.
3-4-5 during
May also indicate that the battery is fully recharged and does not require any
charging
further charging.
No charge
If the battery is totally empty the battery level symbol may not be displayed at once
symbol when
when connecting the battery charger. Moreover the phone cannot be turned on.
connecting the
Up to 15 minutes may be necessary to reach the required 4% battery charge to
charger
turn your phone on and allow the battery charge symbol to be displayed.
Flashing
There is not enough memory to store another SMS message. Delete one or more
of the existing stored messages.
108- Appendix
Error messages
PROBLEM
POSSIBLE CAUSE AND SOLUTION
Allowed credit reached!
You are trying to place an outgoing call and the allowed credit is
already reached.
The allowed credit limit is reached during an outgoing call (the call is
then aborted).
An error occurred in a game execution.
An internal error has
occurred
Busy
Call failed
Cancelled. No type selected
Cannot execute command
Can't display message
Charge error
Check battery!
Check SIM!
Check your password
Check your request
Check your subscription
Connection failed
Connection failure
Error!
Failed
File protected
File too big
Incorrect entry
Invalid data received
Invalid number
You are trying to make a call and the call fails because the destination
number is already engaged in conversation.
The user is unreachable.
the network is busy or the number is out of order or
the number is invalid number or
the network does not answer or
the option to hide your phone number when calling is not supported
by the network
Control the ability to hide your ID when making a call (service
availability in network).
Cell broadcast activation has been requested but no message type
has been selected.
You have made a request which is impossible to execute in the
current call situation.
The short message text cannot be displayed (characters not
recognised, incorrect format etc.)
A problem occurred during mobile battery charge process.
A battery problem has been detected.
There is no SIM present or the SIM is incorrectly inserted.
You changed the call barring password or
You changed the call barring service status.
The entered password seems to be wrong or incorrect.
You made a request for a service that seems to be unavailable.
You tried to activate a GSM service. You are requested to check your
subscription regarding the related service rights of use/access.
Connection with the server cannot be established for one of the
following reasons:
The server is busy. Try to connect later.
The server is down. Try to connect later.
The network is not reachable. Check the GPRS service icon is
displayed in standby mode.
The connection data failed.
The network cannot perform your request and generates an error.
An SMS sending process failed (the short message cannot be sent).
The file cannot be exported (copyright).
The file dimensions (pixels) and/or weight (KB) are not adapted to
your phone. Resize the file (The maximum allowed file size depends
on your service provider).
You entered a character string with a syntax error.
The received file bears invalid information or the melody format
cannot be recognised by the phone.
You tried to make a call and the call is rejected by the network because
the network does not recognise the phone number structure.
You tried to store a phone number that is too long to be stored in the
selected location.
You tried to move a phone entry to a location that is unable to receive
the phone number (phone number too long).
109- Appendix
Low battery!
The battery is low and the phone will soon be switched off
automatically.
Network busy
You tried to make a call. The call is rejected by the network due to
congestion problems.
Network not allowed
When selecting network manual search, you have selected a network
that rejects the connection.
New PIN2 incorrect. Try again Changing PIN2: the new PIN2 code values differ (value control).
New PIN incorrect. Try again Changing PIN: the new PIN code values differ (value control).
No connection
No connection is defined in the connection profile.
No match!
No matching pattern has been found between the pronounced
sentence and the recorded sentences from the voice dialling database.
No response
You made a call to a remote user and no response has been received.
Not allowed
Your number/character entry is not allowed.
Not allowed fixed dialling
A call is tried, but cancelled due to fixed dialling control (the number
dialled does not match with one of the fixed dialling numbers in memory).
Not enough place in the
The corresponding memory is full.
phone memory
Not enough place in the SIM
memory
Number changed
The called number has changed.
Page has no content
Your request was accepted by the network but the required server
page is empty.
Phone permanently blocked A wrong PUK code has been entered 10 times. The phone is now
permanently blocked.
PIN blocked
A wrong PIN code has been entered 3 times.
PIN2 blocked
A wrong PIN2 code has been entered 3 times.
PUK2 blocked
A wrong PUK2 code has been entered 10 times.
The SIM services protected by the PIN2 code have now been
permanently disabled.
Reaching allowed credit!
The cost limit is about to be reached. The connected call ends
automatically when the limit is reached.
Ring volume Off
The ring volume is set to 0 (no volume).
Service not available
Activating some GSM services that are not available on the network
SIM blocked. Contact
A wrong PUK has been entered 10 times.
provider
The SIM card has been permanently disabled and needs to be replaced
by a new one.
SIM names Phone book full The corresponding memory is full.
Phone names Phone book
full
Undeletable file
The file cannot be deleted (copyright protected).
Wrong code. Try again
A wrong phone lock code has been entered.
Wrong new code. Try again The new phone lock codes do not match (value control).
Wrong PIN, try again
The wrong code has been entered.
Wrong PIN2, try again
Wrong PUK, try again
Wrong PUK2, try again
Wrong SIM inserted: phone A SIM card, different from the SIM to which the phone is usually
locked
locked, has been inserted in the phone.
Invalid SIM
Not enough space
The corresponding memory is full or nearly full..
Too many applications
The number of applications in the phone has already reached the
maximum (50).
110- Appendix
Guarantee
PAN EUROPEAN SERVICE
Should you experience any difficulty, please contact your nearest Mitsubishi Electric representative in the list below for information on service centres.
UNITED KINGDOM
Tel: (0800) 912 00 20
FRANCE
Tel: (0825) 86 82 83
BELGIUM
Tel: (0800) 75733
LUXEMBURG
Tel: (800) 23552
PORTUGAL
Tel: (0800) 880264
SPAIN
Tel: (902) 11 68 58
ITALY
Tel: (800) 79 10 29
IRELAND
Tel: (1850) 200 240
GERMANY
Tel: (01803) 33 71 84
NETHERLANDS
Tel: (0800) 0223 825
GREECE
Tel: (800) 4413 1247
Important: to obtain the Mitsubishi Electric warranty service, the original purchase invoice from
the dealer is required.
PAN-EUROPEAN END-USER GUARANTEE CONDITIONS
1.Melco Mobile Communications Europe S.A. (MMCE) guarantees that for a period of twelve
(12) months from the date of purchase from the dealer, the product shall be free from defects
in materials and workmanship. If the statutory warranty in force in your country exceeds 12
months, the statutory warranty is not affected by this manufacturer’s guarantee. This guarantee
also covers batteries for a period of twelve (12) months from the date of purchase from the dealer. Subject to the conditions below, MMCE will indemnify you for the cost of all parts and labour
for repairs, or the replacement of the product or parts (which may include equipment of similar
type) where conducted by an approved Mitsubishi Electric service centre. MMCE shall be entitled to retain any product that has been replaced.
2.All claims must be made to an approved Mitsubishi Electric service centre. You can contact
the Mitsubishi Electric representatives listed above to obtain details of your nearest approved
Mitsubishi Electric service centre. As a condition of this guarantee, the date of the purchase
must be confirmed by producing the original invoice from the dealer. The final determination of
guarantee claim eligibility shall be made by MMCE.
3.This guarantee does not cover:
a)non-compliance with directions for use;
b)installation or removal charges where the product is installed in a vehicle;
c)defects or failures caused by accident, misuse, improper installation or improper repair by a
non-approved repairer, alteration or modification, neglect, failure to use the phone for normal
purposes, Acts of God, exposure to water, use in adverse environmental conditions (humidity
or temperature);
d)cost of or performance of any modifications to the product to adapt or adjust it to conform to
national or local safety laws, where such safety laws go beyond agreed European Union standards;
e)loss of use of the product or consequential loss of any nature;
f)loss of use of air-time, loss of use of any loaned equipment or ancillary equipment;
g)provision of incorrect or insufficient signal on air-time network, upgrading of product software
to changes in network operating parameters, main supply voltage fluctuations, incorrect SIM
card (miniSD™ Card) parameters for connection to airtime retailer;
h)damage caused by non-Mitsubishi Electric accessories.
4.Any guarantee claim or service does not extend the original guarantee period unless so required by prevailing national law.
5.This guarantee is valid only if the product is purchased and used in the European Union, Norway, Iceland or Switzerland.
THIS GUARANTEE DOES NOT AFFECT YOUR STATUTORY RIGHTS.
MELCO MOBILE COMMUNICATIONS EUROPE S.A.
5, rue de la Chataigneraie
35510 Cesson Sévigné
France
www.mitsubishi-telecom.com
111- Appendix
INDEX
A
AC/DC adaptor charger ................... 7
Active flip .................................. 98
Adjusting the preview .............. 64, 67
Alarm clocks ............................... 19
Alert mode .................................. 94
Answering a call ........................... 12
Any key answer ........................... 97
Application
Downloading ............................ 81
Launching ............................... 80
Auto Switch On/Off ...................... 98
Automatic search ....................... 103
Auto-Retry .................................. 98
B
Backlight .................................... 96
Balance information ...................... 42
Battery
Disposal ................................... 8
Use .......................................... 7
Bookmarks
Creating .................................. 90
Using ..................................... 90
Brightness ............................ 55, 64
C
Calculator ................................... 18
Calendar .................................... 87
Call
Duration .................................. 42
Recorded ................................ 43
Reminder ................................ 42
Times ..................................... 41
6
Call barring ............................... 104
Password .......................... 8, 104
6
Call cost
Reset ..................................... 43
Call diverting ............................. 100
Call hold ................................... 101
Call management
Call costs ................................ 42
Call timer
Reset ..................................... 42
Call waiting ............................... 101
Caller line identity ....................... 102
Calls & Times .............................. 41
Call costs .......................... 42, 43
Call logs ................................. 41
Call timers ......................... 41, 42
Line selection ........................... 43
Camera
Adjusting a picture .................... 59
Adjusting the preview ................ 54
Application .............................. 52
Brightness ................... 54, 55, 61
Compact light ..................... 52, 56
Contrast .................................. 52
Features ................................. 53
Icons ................................ 52, 56
Macro switch ........................... 56
Mode ..................................... 55
Picture erasing ................... 54, 58
Picture quality .......................... 55
Picture size ............................. 54
Picture storing .................... 54, 58
Picture taking ........................... 54
Quality .............................. 52, 59
Resolution ................... 52, 54, 59
Scenery shots .......................... 53
Self picture taking ............... 57, 58
Self timer .......................... 52, 56
Shortcuts ................................ 57
Storage memory ....................... 55
Zoom ......................... 52, 55, 61
6
Camera application ........... 58, 60, 64
Care and maintenance .................... 7
Certificate .................................. 105
Clamshell
Closed ................. 53, 61, 62, 79
Open ................... 57, 61, 66, 79
CLI .......................................... 102
Clocks
Format .................................... 99
Origin clock .............................. 99
Secondary clock ........................ 99
Setting .................................... 99
Swap ...................................... 99
Closed clamshell ............. 61, 62, 79
Code
PIN .................................. 8, 104
PIN2 ................................ 8, 104
PUK ..........................................8
PUK2 ........................................8
Compact light ..... 52, 56, 59, 61, 65
Connection manager ..................... 99
Operation mode ...................... 100
Connection profiles ....................... 99
Connection settings ....................... 88
Credit limit ................................... 43
Cropping ..................................... 71
Currency-converter ....................... 18
D
Data exchange ............................. 82
Declaration of conformity ..................6
Diary
Calendar ........................... 15, 16
Exporting an event ..................... 17
Sending an event ...................... 17
Storage used ............................ 18
Tasks list ................................. 17
Display ................................ 13, 95
Downloaded melody ............... 73, 76
Downloading
Infrared port ............................. 71
E
Editing a phonebook card ............... 47
Editing a SIM name card ................ 47
Editing a text model ....................... 27
Edition mode ................................ 23
e-mail
Composing an e-mail ................. 38
e-mail profiles ........................... 39
Inbox ...................................... 37
Outbox .................................... 40
Preparing your phone ................. 39
Reading ................................... 37
Ending a call ................................ 13
Entering text ................................ 23
Erasing a video ..................... 64, 67
Error messages .......................... 109
Export ........................................ 51
Exporting an event/task .................. 17
External screen ....................... 9, 13
Extracting the miniSD™ Card .......... 85
F
Fixed dialling numbers ................... 50
Frame ........................................ 78
Adding .................................... 79
Browser ................................... 78
Downloading ............................ 80
Viewing ................................... 79
Fun & Media box .......................... 69
Frame ..................................... 78
miniSD™ Card ....... 71, 73, 75, 77
Others ..................................... 81
Picture .................................... 69
Playing a video ......................... 74
Receiving a video ...................... 75
Speech notes ........................... 77
Storage used ............................ 83
Stored videos ........................... 73
Video ...................................... 73
G
Games
Applications .............................. 80
Downloading ............................ 81
112- Index
Launching ................................ 80
Gateway settings
IP address ............................... 35
General Safety ............................... 6
Glossary ................................... 107
Goodbye screen ........................... 96
GPRS ..................................10, 13
Graphic display icons .................... 10
GSM Services ............................ 100
Call diverting .................. 100, 101
Network ................................ 103
H
Holding
your mobile
.......13, 54, 58, 63, 66
I
Icons ....................... 10, 61, 62, 65
i-mode icons ............................. 25
Image
Quality .................................... 64
Size ........................................ 64
i-mode
Icons ...................................... 25
Information numbers ..................... 89
Infrared port ................................. 19
Opening .................................. 20
Inserting the miniSD™ Card ............ 85
K
Keypad ....................................... 96
Keypad lock ...........................14, 96
Keys ............................................ 9
Actions ...................................... 9
L
Line 1 .................... 41, 43, 50, 100
Line 2 ..............30, 41, 43, 50, 100
Loop mode .................................. 62
M
Macro switch ............................... 56
Macro switch setting ...................... 65
Main screen ................................. 13
Making a call ............................... 12
Melodies
miniSD™ Card .......................... 85
Melody .................................73, 76
Download ..........................73, 77
miniSD™ Card ....................74, 77
Memory
Storage used ............................ 86
Messages
Drafts ..................................... 36
Edition mode ............................ 23
Menu ...................................... 21
Outbox .................................... 28
Settings ................................... 23
SMS ....................................... 21
Storage used ............................ 30
Text models ............................. 27
Text symbols ............................ 25
Write new ................................ 27
Microphone ...........................61, 65
miniSD™ Card ..................... 84, 106
Accessing ................................ 85
Configuring .............................. 86
Extracting ................................ 85
Inserting .................................. 85
Melodies .................... 73, 77, 85
Music ...................................... 85
Other files ................................ 86
Pictures .............................72, 85
Speech notes ........................... 86
Video ................................76, 85
MMS .......................................... 31
Auto-retrieval ............................ 35
Characteristics .......................... 35
Content ................................... 32
Inbox ...................................... 31
MMS profiles ......................32, 35
Notification ............................... 31
Outbox .................................... 36
Preparing your phone ................. 34
Reading .................................. 31
Selecting an addressee .............. 32
Subject ................................... 32
To attach an image .................... 33
Writing .................................... 33
Mobile number
Hiding ................................... 102
Showing ................................ 102
Modem ....................................... 20
Multimedia messages .................... 31
Multipress text entry ...................... 24
Multitap text entry ......................... 24
My card ...................................... 50
My number .................................. 50
My picture ................................... 96
N
Network .................................... 103
Network serv. .............................. 87
O
Online connection
Bookmarks .............................. 90
Ending .................................... 89
Personalising ........................... 90
Open clamshell ............... 61, 66, 79
Operation mode
Modem ................................. 100
Standard ............................... 100
Outbox ....................................... 28
P
Pausing a video ........ 61, 62, 64, 67
Phone card
Update .................................... 44
Phone lock ................................ 104
Code ................................ 8, 104
Phone names card ........................ 44
Phone numbers
Storing .................................... 44
Phone settings ............................. 94
Phonebook .................................. 44
Add name ............. 44, 45, 46, 47
Calling numbers ........................ 48
Copy ...................................... 45
Copy all ................................... 45
Deleting images ........................ 46
Export ..................................... 51
Fixed dialling ............................ 50
Folder selection ........................ 48
Free space .............................. 49
Group ..................................... 49
My numbers ............................. 50
Read ...................................... 48
SIM names card ........................ 44
Sorting .................................... 48
Storage used ............................ 49
Storing a received number .......... 45
Storing names .......................... 44
Storing phone numers ................ 44
Viewing & calling ....................... 48
Voice dialling ...................... 48, 49
Phonebook card
Image ..................................... 44
Picture ....................................... 71
Album ............................... 69, 79
Album 2 .................................. 69
Browser .................................. 69
Erasing ............................. 54, 58
miniSD™ Card ......................... 71
Quality .................................... 55
Size ........................................ 54
Storing .............................. 54, 58
Taking .................................... 54
Viewer .................................... 69
Viewing ............................. 56, 60
Pictures
Album ..................................... 79
Size ........................................ 52
Pictures list ................................. 44
Pictures viewer options .................. 70
PIN code .............................. 8, 104
PIN2 code ............................. 8, 104
Playing a video ............... 62, 68, 74
Power saver ................................ 14
PUK code ..................................... 8
PUK2 code ............................ 8, 105
Push messages
Receiving ................................ 91
R
Receiving a video
......................... 75
Receiving caller ID ...................... 102
Recorded call .............................. 43
Recording a video .................. 61, 63
Rejecting a call ............................ 13
Reminder - call duration ................. 42
Ring .......................................... 94
Ring tone .................................... 94
Stop ....................................... 13
S
Safety information .......................... 6
Disposing of waste packaging ........ 8
Emergency calls ......................... 7
Security codes ........................... 8
Vehicle safety ............................ 6
Your responsibility ....................... 8
SAR ............................................ 5
Saving MMS content ..................... 31
Scenery shots .............................. 62
Screen
External screen ..............9, 13, 95
Goodbye screen ....................... 96
Main screen ...................9, 14, 97
Welcome screen ....................... 97
Security ............................ 104, 106
Codes ...................................... 8
Features ............................... 104
Self timer ................. 52, 56, 61, 65
Self-filming ............................ 66, 67
Sending a video ........................... 64
Sending an event/task ................... 17
Sending my ID ........................... 102
Setting an image
External screen ........................ 71
Goodbye screen ....................... 71
Idle screen .............................. 71
Main screen ............................. 71
Welcome screen ....................... 71
Settings
Active flip ................................ 98
Any key answer ........................ 97
Auto features ........................... 98
Backlight ................................. 96
Broadcast ................................ 29
Connection manager ................. 99
Contrast .................................. 96
Default settings ........................ 99
External screen ........................ 95
GSM Services ........................ 100
Idle screen .............................. 95
Keypad ................................... 97
Language selection ................... 97
Main screen ............................. 95
My picture ............................... 96
Phone settings ................... 97, 98
Security ........................ 104, 105
Security features ..................... 104
Softkey functions ...................... 97
Time and date .......................... 99
Tones ............................... 94, 95
Voice Mail ............................... 30
Wap™ .................................... 88
Welcome screen ....................... 96
Shortcuts .............................. 57, 66
Show costs ................................. 43
Silent ......................................... 94
SIM card
Update ................................... 45
SMS messages
Draft ....................................... 28
Forward .................................. 22
Insert ...................................... 25
Move to SIM ............................ 21
Reading .................................. 21
Sending .................................. 26
Writing .................................... 23
Softkeys functions ........................ 97
Solutions .......................... 108, 109
Sound level ................................. 62
Special characters ........................ 25
Speech notes .............................. 77
miniSD™ Card ......................... 86
Record new ............................. 77
Speed dial .................................. 97
Standby display ........................... 13
And Welcome screen animation ... 69
Stopping a video .................... 61, 62
Storage used ......................... 18, 83
113- Index
Storing a video
Storing names
...................... 64, 67
..............................44
T
T9 ..............................................25
T9 text entry .................................25
Text edition
i-mode icons .............................25
Insert ......................................25
Special characters .....................25
Text models ..............................25
Text entry
Multipress mode ........................24
Multitap mode ...........................24
T9 mode ..................................24
Text model
Editing .....................................27
Text writing ..................................23
Ticket ....................................... 106
Tones .........................................94
Tools ..........................................15
Alarm clocks .............................19
Calculator ................................18
Currency converter ....................18
Diary .......................................15
Infrared port ..............................19
Turning the phone off .....................14
Turning the phone on .....................12
V
vCalendar
Sending ...................................83
Storing ....................................82
vCard
Sending ...................................83
Storing ....................................82
Vehicle safety .................................6
Vibrate ........................................94
& ring ......................................94
Then ring .................................94
Video ................................... 61, 73
Adjusting the preview .......... 64, 67
Application ........................ 61, 67
Brightness ................................64
Compact light ..................... 61, 65
Display ....................................61
Duration ............................ 61, 62
Erasing ............................. 64, 67
Features ..................................62
Full screen option ......................68
Holding your mobile ...................66
Icons ................................ 61, 62
Image Size ...............................64
Loop mode ...............................62
Macro switch setting ...................65
Microphone ....................... 61, 65
miniSD™ Card ................... 75, 85
Pausing ................61, 62, 64, 67
Playback ..................... 62, 68, 74
Player .....................................62
Quality .............................. 61, 64
Receiving .................................75
Recorder ........................... 61, 63
Recording ................................63
Resolution ................................61
Scenery shots ...........................62
Self timer .................................61
Self-filming ........................ 66, 67
Sending ...................................64
Shortcuts .................................66
Size ........................................61
Size limit ..................................65
Sound level ..............................62
Stopping ........................... 61, 62
Storage memory ........................65
Stored .....................................73
Storing ............................. 64, 67
Weight .....................................61
Zoom ............................... 61, 64
Video player .................................64
Viewing an image ................... 69, 79
Viewing tickets ...........................106
Voice dialling
Creating a voice pattern ..............48
Making a call ............................48
Voice Mail
Activating .................................29
Alert ........................................29
Alert tone ................................
Call ........................................
Deactivating ............................
Number ..................................
Volume
Alarm .....................................
Conversation ...........................
Key tones ................................
Ring .......................................
Volume adjustments .....................
29
29
29
29
94
94
94
94
94
W
Wap™ ....................................... 88
Bango address ......................... 91
Bookmarks .............................. 90
Go to site ................................ 91
Home page ............................. 89
IP address ............................... 88
New address ........................... 91
Personalising ........................... 90
Preferred bearer ....................... 90
Profile details ........................... 88
Profiles ................................... 88
Saved pages ........................... 91
Settings ...................... 88, 90, 92
Site history .............................. 91
Wap profiles ............................ 90
Welcome screen .......................... 69
WIM card .................................. 105
WIM Manager ............................ 106
Writing text
Edition mode ........................... 23
Z
Zoom
...................... 52, 55, 61, 64
114- Index