AB
DESKTOP AUDIO SYSTEM
TSX-112
OWNER’S MANUAL
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
Install this unit in a well ventilated, cool, dry, clean
place - away from direct sunlight, heat sources,
vibration, dust, moisture and cold. For proper
ventilation, allow the following minimum clearances.
Top: 15 cm (6 in)
Rear: 10 cm (4 in)
Sides: 10 cm (4 in)
Locate this unit away from other electrical
appliances, motors, or transformers to avoid
humming sounds.
Do not expose this unit to sudden temperature
changes from cold to hot, and do not locate this unit
in an environment with high humidity (i.e. a room
with a humidifier) to prevent condensation inside this
unit, which may cause an electrical shock, fire,
damage to this unit, and/or personal injury.
Avoid installing this unit where foreign object may
fall onto this unit and/or this unit may be exposed to
liquid dripping or splashing. On the top of this unit,
do not place:
– Other components, as they may cause damage
and/or discoloration on the surface of this unit.
– Burning objects (i.e. candles), as they may cause
fire, damage to this unit, and/or personal injury.
– Containers with liquid in them, as they may fall
and liquid may cause electrical shock to the user
and/or damage to this unit.
Do not cover this unit with a newspaper, tablecloth,
curtain, etc. in order not to obstruct heat radiation. If
the temperature inside this unit rises, it may cause
fire, damage to this unit, and/or personal injury.
Do not plug in this unit to a wall outlet until all
connections are complete.
Do not operate this unit upside-down. It may
overheat, possibly causing damage.
Do not use force on switches, knobs and/or cords.
When disconnecting the power cable from the wall
outlet, grasp the plug; do not pull the cable.
Do not clean this unit with chemical solvents; this
might damage the finish. Use a clean, dry cloth.
Only voltage specified on this unit must be used.
Using this unit with a higher voltage than specified is
dangerous and may cause fire, damage to this unit,
and/or personal injury. Yamaha will not be held
responsible for any damage resulting from use of this
unit with a voltage other than specified.
To prevent damage by lightning, keep the power
cable disconnected from a wall outlet or this unit
during a lightning storm.
Do not attempt to modify or fix this unit. Contact
qualified Yamaha service personnel when any
service is needed. The cabinet should never be
opened for any reasons.
i En
15 When not planning to use this unit for long periods of
time (i.e. vacation), disconnect the AC power plug
from the wall outlet.
16 Be sure to read the “TROUBLESHOOTING” section
on common operating errors before concluding that
this unit is faulty.
17 Before moving this unit, press to set the system to
off, and disconnect the AC power plug from the wall
outlet.
18 Condensation will form when the surrounding
temperature changes suddenly. Disconnect the power
cable from the outlet, then leave this unit alone.
19 When using this unit for a long time, this unit may
become warm. Turn the system off, then leave this
unit alone for cooling.
20 Install this unit near the wall outlet and where the AC
power plug can be reached easily.
21 The batteries shall not be exposed to excessive heat
such as sunshine, fire or the like. When you dispose
of batteries, follow your regional regulations.
22 Excessive sound pressure from earphones and
headphones can cause hearing loss.
This unit is not disconnected from the AC power source
as long as it is connected to the wall outlet, even if this
unit itself is turned off by . In this state, this unit is
designed to consume a very small quantity of power.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR
MOISTURE.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
There is a chance that placing this unit too close to a
CRT-based (Braun tube) TV set might impair picture
color. Should this happen, move this unit away from the
TV set.
English
CONTENTS
NAMES OF PARTS AND THEIR
FUNCTIONS...............................................2
CONNECTING AN iPod .............................6
ADJUSTING THE CLOCK..........................7
LISTENING TO iPod ..................................7
LISTENING TO CD AND USB DEVICE .....8
SWITCHING THE DISPLAY.......................9
LISTENING TO DAB STATIONS .............10
LISTENING TO FM STATIONS ...............13
USING ALARM FUNCTION..................... 15
SHUFFLE/REPEAT PLAYBACK ............. 17
LISTENING TO EXTERNAL SOURCE.... 18
USING SLEEP FUNCTION...................... 18
USING OPTION MENU ........................... 19
TROUBLESHOOTING ............................. 21
NOTES ON DISCS AND
USB DEVICES ......................................... 25
SPECIFICATIONS ................................... 26
X Features
– iPod/iPhone, CD, USB device, radio and external device using AUX are playable.
– Providing comfortable wake-up by the music set with your preferred volume with alarm function.
Music, beep sound, or both can be set as alarm sound.
– Storing/calling your favorite radio stations (up to 30 DAB and 30 FM stations).
– Bass and treble can be controlled depending on your favorite.
X About this manual
• “iPod” described in this manual may also refer to “iPhone”.
• This manual describes how to operate this unit using buttons on the unit. Some of these operations are also
available using the remote control.
• The symbol “☞” with page number(s) indicates the corresponding reference page(s).
• Notes contain important information about safety and operating instructions. y indicates a tip for your
operation.
• This manual is printed prior to production. Design and specifications are subject to change in part as a
result of improvements, etc. In case of differences between the manual and the product, the product has
priority.
X Supplied accessories
Remote control
DAB/FM antenna
Dock cover
SNOOZE / SLEEP
ALARM
CD
CLOCK
iPod
RADIO
AUX
USB
FOLDER
MENU
ENTER
OPTION
DISPLAY
VOLUME
MUTE
TUNING
MEMORY
PRESET
(With CR2032 battery)
1 En
PREPARATION
NAMES OF PARTS AND THEIR FUNCTIONS
X Top panel, front panel
1
2
IPod/iPhone
LABEL SIDE
IPod/iPhone
LABEL SIDE
34
RETURN
ENTER
5 6 7
8
9
VOLUME
SOURCE
PRESET
USB
ALARM
SNOOZE / SLEEP
RETURN
ENTER
VOLUME
SOURCE
PRESET
USB
ALARM
SNOOZE / SLEEP
0
A
B
C
D
E
1 iPod dock: Set an iPod.
7
2 Disc slot (☞ P. 8)
8 RETURN: Returns to the previous item while setting.
3
9 ENTER: Confirms the setting.
: Press to turn the system on/off.
4 Alarm indicator: Lights up when the alarm function
is activated and flashes while setting the alarm.
(☞ P. 15)
5 SOURCE: Change sources.
6 Front panel display: Displays various information.
Time is displayed when the system is off.
If you set the system to power save mode, all the
information on the front panel display is turned off,
and reduce power consumption.
For more information how to set power save mode,
refer to “Rear panel (Connecting antenna)”.
(☞ P. 4)
2 En
: Ejecting the CD.
0 USB port (☞ P. 8)
y
When a USB device is connected to the USB port, the
device is charged. During system off/power save mode,
the device is not charged.
A
(Headphones jack): Connect headphones.
B ALARM: Alarm on/off (☞ P. 16)
C PRESET (During receiving radios): Select the preset
radio station. (☞ P. 14)
– / +: Changes the setting (☞ P. 15)
D SNOOZE/SLEEP (☞ P. 16, 18)
E Audio control buttons: Skip, search backward/
forward, play/pause, stop, volume control
NAMES OF PARTS AND THEIR FUNCTIONS
English
X Front panel display
1
2
3
4
SLEEP PRESET STEREO AUTO
TUNED MEMORY
5
6
7
SHUFFLE REPEAT
ARTISTS ALBUMS SONGS
MUTE
B
8
9
0
A
1 SLEEP indicator: Lights up when the sleep timer is
on. (☞ P. 18)
8 Multi information display: Shows the various
information.
2 PRESET indicator: Lights up when you preset radio
stations. (☞ P. 14)
9 TUNED indicator: Lights up when this unit is tuned
into a station. (☞ P. 13)
3 STEREO indicator: Lights up when this unit is
receiving a strong signal from an DAB/FM stereo
broadcast.
0 MEMORY indicator: Flashes when searching for a
radio station by automatic preset tuning. Lights up
when you preset radio stations automatically or
manually. (☞ P. 14)
4 AUTO indicator: Lights up when this unit is in the
Automatic Tuning mode. (☞ P. 13)
5 SHUFFLE indicator: Lights up when you set your
iPod/CD/USB to shuffle play. (☞ P. 17)
6 REPEAT indicator: Lights up when you set your
iPod/CD/USB to repeat play. (☞ P. 17)
7 MUTE indicator: Lights up when the sound is
muted.
A Multi information indicators: Indicate the music
information currently displayed on Multi information
display. (☞ P. 9)
B Operation indicators: Show the available menu
buttons for the currently selected OPTION menu
item.
3 En
NAMES OF PARTS AND THEIR FUNCTIONS
X Rear panel (Connecting antenna)
1 2
3
4
SET ON OFF
5
1 DAB/FM antenna (supplied)
2 DAB/FM antenna terminal: Connect the supplied
DAB/FM antenna.
3 AUX: Connect an external device. (☞ P. 18)
4 CLOCK
SET: Adjusts the clock. (☞ P. 7)
ON: Displays the current time when system is off.
OFF: Switches the system to power save mode
when system is off.
All the information on the front panel display is
turned off in this mode. This can reduce power
consumption.
y
Even in system off/power save mode, the alarm function
is available.
4 En
5 Power cable: Connect to a wall outlet.
Notes
• The antenna should be stretched out.
• If DAB/FM reception is poor, change the height, direction,
or placement of the antenna.
NAMES OF PARTS AND THEIR FUNCTIONS
1
2
3
A
SNOOZE / SLEEP
ALARM
CLOCK
CD
iPod
B
AUX
4
USB
RADIO
5
6
FOLDER
MENU
C
ENTER
7
D
OPTION
8
DISPLAY
E
MUTE
F
VOLUME
G
9
TUNING
H
MEMORY
PRESET
0
X Using the remote control
Be sure to read “BATTERY CAUTIONS”
(☞ P. 26) before using the battery.
RETURN
ENTER
VOLUME
SOURCE
PRESET
USB
ALARM
SNOOZE / SLEEP
1 Infrared signal transmitter
2 SNOOZE/SLEEP: Snooze/sleep setting.
(☞ P. 16, 18)
Press and hold this button, then press Cursor T/S
J ENTER to set the sleep function.
3 ALARM: Alarm on/off (☞ P. 16)
4 Source buttons: Change sources. When listening
to the radio, press RADIO to switch between the
DAB and FM bands.
5 FOLDER (during data CD/USB playback): Change
folder.
6 , : Scrolls through items on the iPod’s screen.
7 OPTION: Displays the option menu. (☞ P. 19)
8
(Shuffle),
(Repeat) (☞ P. 17)
9 TUNING (during receiving radio): Tuning radio
(☞ P. 13)
0 PRESET (during receiving radio): Select the preset
radio station (☞ P. 14)
A
: System on/off
B CLOCK: Displays the time (☞ P. 7)
C
,
(during playback): Skip backward and
forward/press and hold to rewind and fast-forward
MENU: Returns to the upper level in the iPod menu.
: Play/pause
S/T/W/X (During using the option menu): Changes
the setting
ENTER
(During using the iPod): Select group/start playback
(During using the option menu): Confirms the setting
D : Stop playback.
E DISPLAY: Switches the information shown on the
front panel. (☞ P. 9)
F MUTE: Mute/resume the sound.
G VOLUME: Volume control
H MEMORY: Memories preset radio stations. (☞ P. 14)
X Replacing the battery in the
remote control
While pushing the release tab in direction
,
slide out the battery holder in direction
.
1
Within 6 m
(20’)
CR2032
battery
SNOOZE / SLEEP
ALARM
CD
CLOCK
iPod
RADIO
AUX
USB
2
FOLDER
MENU
ENTER
OPTION
DISPLAY
VOLUME
MUTE
3
TUNING
MEMORY
PRESET
Battery insulation
sheet: Remove
before using.
5 En
English
X Remote control
CONNECTING AN iPod
Set your iPod in the iPod dock.
y
An iPod is charged when set in the iPod dock.
During power save mode, the iPod is not
charged.
Dock Adaptor
Notes
IPod/iPhone
LABEL SIDE
6 En
• To secure the connection, attach a compatible
Dock Adapter supplied with the iPod or an
iPod Universal Dock Adapter (sold
separately), and remove the protective case
covering from your iPod.
• If you do not use an adapter or if the adapter
is not compatible, the connection could be
loose or poor, which could cause damage or
malfunctions. For details on dock adaptor
information, please visit official Apple’s
website.
• If an iPod in protective case is connected by
force, the connector may be damaged.
Remove the protective case before
connection.
• Attach the dock cover to the iPod dock
whenever you are not using it.
English
ADJUSTING THE CLOCK
1
1 Set CLOCK to SET.
2
PRESET
2 Set the time.
ENTER
Press – / + to set the hour and then
press ENTER.
Set the minutes in the same way.
Rear panel
y
Front panel
• While setting the clock, press RETURN
to return to the previous setting.
• Press SNOOZE/SLEEP on the front
panel to switch between the 12 and 24
hour clock display.
3 Set CLOCK to ON to complete.
3
At the time ON is set, it will be 0
second and time count starts.
y
• The time is displayed for a certain period
when you press CLOCK on the remote
control.
• You can switch the system to power save
mode by setting CLOCK on the rear panel to
OFF.
Rear panel
Note
The time settings are lost about 5 minutes after
unplugging the unit.
LISTENING TO iPod
For details on compatible iPod models, refer to “SPECIFICATIONS” (☞ P. 26).
For details on how to operate the remote control, refer to “Remote control” (☞ P. 5).
1
1 Set your iPod in the iPod dock.
2
2 Set SOURCE to iPod.
3 Play the iPod.
SOURCE
Playback operations are available with the
remote control, iPod and this unit.
y
• You can remove the iPod whenever you want.
• When music in the iPod is played back, this unit turns
the system on automatically and plays back the iPod
even if the unit is system off.
y
This unit automatically turns off the system if the iPod is not connected and no operation is performed for 60
minutes.
7 En
OPERATION
LISTENING TO CD AND USB DEVICE
X Listening to CD
1
1 Set SOURCE to CD.
2
2 Insert a CD.
Playback starts automatically. Playback
operations are available with the remote control
and this unit.
SOURCE
y
IPod/iPhone
Playback for Data Disc starts in alphanumeric order of
files.
LABEL SIDE
Note
Insert the CD with the label side facing toward the front
of the unit.
X Listening to USB device
1
1 Set SOURCE to USB.
2
2 Connect a USB device.
RETURN
ENTER
VOLUME
SOURCE
SOURCE
PRESET
USB
ALARM
SNOOZE / SLEEP
Playback starts automatically. Playback
operations are available with the remote control
and this unit.
y
• You can remove your USB device whenever you want.
• Playback starts in order by date and time of creation.
y
• If
button is pressed during playback, next time playback starts from the beginning of the track you listened to last time. If
button is pressed again while playback is stopped, next time playback starts from the first track of the CD/USB device.
• For details on playable discs and files, refer to “NOTES ON DISCS AND USB DEVICES” (☞ P. 25).
• This unit automatically turns off the system 60 minutes after CD/USB device playback is stopped/paused.
X Skipping folder for data CD/USB device
Select the folder with FOLDER.
FOLDER
Remote control
8 En
Skip to the first file in the previous/next folder.
The folder name is displayed on the front panel
display for a certain period.
ROOT is displayed for the root folder when the
directory contains playable files.
English
SWITCHING THE DISPLAY
You can switch the playback information shown on the front panel display. Some special characters may not be
shown properly.
Press repeatedly
Press DISPLAY repeatedly during playback.
DISPLAY
Remote control
iPod
CD/USB
Song number and elapsed time (default setting)
L
Song number and remaining time
L
Song name
L
Artist name
L
Album name
L
Back to the default setting
Track/file number and elapsed time of the current song (default
setting)
L
Track number and remaining time of the current song*1
L
Total time of the disc*1
L
Remaining time of the disc*1
L
File name*2
L
Track name*3
L
Artist name*3
L
Album name*3
L
Back to the default setting
Note
This function is available for iPod classic, iPod nano
(2nd generation and later), iPod touch and iPhone.
However, even with these models, this function may
not be available depending on the software version of
your iPod.
*1
*2
*3
Only for Audio CDs
Only for MP3/WMA files
Only when the selected track has information
9 En
LISTENING TO DAB STATIONS
DAB (Digital Audio Broadcasting) uses digital signals for clearer sound and more stable reception compared to
analog signals.
This unit can also receive DAB+ (an upgraded version of DAB) that allows for more stations using MPEG-4
audio codec (AAC+), which has a more efficient transmission method.
Preparing the DAB tuning
Before tuning into DAB stations, an initial scan must be performed. The initial scan starts automatically when
you select DAB as the input source for the first time.
1 Set SOURCE to DAB.
1
y
SOURCE
You can also perform the initial scan manually by
INIT SCAN (☞ P. 19, 20).
2 The initial scan starts.
2
“Scanning” and the percentage of the progress
of scan appear on the front panel display.
3 Scan is completed.
3
The number of receivable DAB stations
appears on the front panel display for a while,
then the unit airs the first station as stored in
station order.
Note
This unit can receive Band III (174 - 240 MHz) only.
Tuning DAB stations
1
1 Set SOURCE to DAB.
2
2 Select a DAB station with TUNING.
SOURCE
TUNING
Remote control
10 En
LISTENING TO DAB STATIONS
Secondary indicator
Note
When the unit cannot receive the DAB signal, “Off Air” is displayed on the front panel display.
Presetting DAB stations
You can store your favorite DAB stations with the preset function. The PRESET indicator lights up on the front
panel display (☞ P. 3).
1
2
1 Tune into a favorite DAB station.
2 Press MEMORY.
MEMORY
SOURCE
Remote control
3
4
3 Select the preset number you want to
store to.
MENU
ENTER
ENTER
4 Press ENTER to complete.
y
Remote control
Remote control
You can preset up to 30 DAB stations.
• To cancel the preset while choosing a preset number,
press MEMORY again.
• You can delete a preset station by pressing OPTION J
Cursor S/T J ENTER to select PRESET DELETE.
Selecting preset DAB stations (Preset tuning)
PRESET
Select the preset radio station in DAB
mode.
11 En
English
Some stations have sub (secondary) stations. The
secondary indicator lights up when a secondary
audio station is selected.
LISTENING TO DAB STATIONS
DAB station information
While listening the DAB station.
Press repeatedly
Press DISPLAY repeatedly.
DISPLAY
Remote control
STATION LABEL
Displays the name of the current DAB station and preset number.
L
DLS (Dynamic Label Segment)
Displays information about the current DAB station, such as the name of the song, artist and speaker, etc. This data is
continuously updated by the DAB broadcaster, thus changing often with every new song or program.
Other data, such as news, weather, and sports headlines, may be broadcast as well.
L
ENSEMBLE LABEL
Displays the name of the current ensemble.
L
CHANNEL / FREQ
Displays the channel label and frequency of the current DAB station.
L
SIGNAL QUALITY
Displays signal reception quality (from 0 (none) to 100 (best)) of current DAB tuning.
L
AUDIO FORMAT
Displays the audio format of the current station, and whether DRC (Dynamic Range Control)* is activated. “(DRC ON)” is
displayed when DRC information is transmitted by DAB station.
* Some DAB broadcasters transmit a wide dynamic range enabling high quality sound, accompanied by DRC information.
Use this feature to compress the dynamic range of the DAB broadcast. This is especially useful when you listen to a DAB
station in a noisy environment or at low volume at night.
L
Back to the STATION LABEL
Note
Not all DAB broadcasters transmit station information.
12 En
LISTENING TO FM STATIONS
English
DAB frequency information
This unit can receive Band III only.
Frequency
Channel label
Frequency
Channel label
174.928 MHz
5A
208.064 MHz
9D
176.640 MHz
5B
209.936 MHz
10A
178.352 MHz
5C
211.648 MHz
10B
180.064 MHz
5D
213.360 MHz
10C
181.936 MHz
6A
215.072 MHz
10D
183.648 MHz
6B
216.928 MHz
11A
185.360 MHz
6C
218.640 MHz
11B
187.072 MHz
6D
220.352 MHz
11C
188.928 MHz
7A
222.064 MHz
11D
190.640 MHz
7B
223.936 MHz
12A
192.352 MHz
7C
225.648 MHz
12B
194.064 MHz
7D
227.360 MHz
12C
195.936 MHz
8A
229.072 MHz
12D
197.648 MHz
8B
230.784 MHz
13A
199.360 MHz
8C
232.496 MHz
13B
201.072 MHz
8D
234.208 MHz
13C
202.928 MHz
9A
235.776 MHz
13D
204.640 MHz
9B
237.488 MHz
13E
206.352 MHz
9C
239.200 MHz
13F
LISTENING TO FM STATIONS
Tuning FM stations
1
1 Set SOURCE to FM.
2
SOURCE
TUNING
2 For automatic tuning, press and hold TUNING.
For manual tuning, press TUNING repeatedly.
Note
If you tune to a station manually, the sound is monaural.
Remote control
13 En
LISTENING TO FM STATIONS
Presetting FM stations
You can store your favorite 30 FM stations with the preset function.
X Automatic preset tuning
1
2
1 Set SOURCE to FM.
3
Press and hold
ENTER
MEMORY
SOURCE
2 Press and hold MEMORY for
more than 2 seconds.
y
Remote control
Remote control
To cancel the preset, press MEMORY again
before step 3 is completed.
3 Press ENTER.
The automatic preset starts.
Note
When you perform the automatic preset, all
stored stations are cleared and the new stations
are stored.
X Manual preset tuning
1
2
1 Tune into a favorite FM station.
2 Press MEMORY.
TUNING
MEMORY
Remote control
3
Remote control
4
3 Select the preset number you
want to store to.
MENU
y
ENTER
ENTER
Remote control
Remote control
To cancel the preset, press MEMORY
again.
4 Press ENTER to complete.
Selecting preset FM stations
1
1 Set SOURCE to FM.
2
PRESET
SOURCE
2 Select the preset FM station with
PRESET.
y
You can delete a preset station by pressing
OPTION J Cursor S/T J ENTER on the
remote control to select PRESET DELETE.
14 En
English
USING ALARM FUNCTION
Alarm features
This unit can play back your favorite music and/or beep sound at the set time. Alarm features on this unit are
described below.
• This unit has 3 alarm types combining music and beep sound:
SRC+BEEP
Selected audio source and the beep sound are played at the set time. Source playback begins to fade
in 3 minutes before the set time and the volume gradually increases to the set volume. Then, at the set
time, the beep sound is activated. This mode is recommended for a comfortable wake-up.
SOURCE
Selected source plays at the set time. Fade-in volume gradually increases to the set volume.
BEEP
Only beep sound is played back at the set time.
• Alarm source played back at the set time can be selected from iPod, audio CD, data CD, USB
device, and radio. Depending on the source, followings also can be selected:
SOURCE
Selectable item
Function
iPod
Resume play
Audio CD/Data CD/
USB
Track
The Selected track is played back repeatedly.
Resume play
The track you listened to last time is played back.
DAB/FM
Preset
The selected preset radio station is played.
Resume play
The radio station you listened to last time is played.
The track you listened to last time is resumed.
• Snooze function is also available.
Alarm setting
X Setting the alarm time and sound
1
Press and hold
2
ENTER
PRESET
1 Press and hold ALARM for more
than 2 seconds.
Alarm indicator (
items flash.
ALARM
) and setting
2 Set the alarm time.
Press – / + to set the hour and then
press ENTER.
Set the minutes in the same way.
3
ENTER
PRESET
4
Select from SRC+BEEP, SOURCE
or BEEP. For the details on alarm
type, refer to “Alarm features”
(☞ P. 15).
4 Select the source (as required).
(As required)
PRESET
3 Set the alarm type.
ENTER
When you select SRC+BEEP or
SOURCE, select source. A source
other than AUX can be selected.
15 En
USING ALARM FUNCTION
5 Select a track or radio station (as
required).
5
(As required)
ENTER
PRESET
When the source is CD/USB/DAB/
FM, select a track or radio station for
alarm.
y
• To select the last song or radio station you
listened to, select “---”.
• When the iPod is set as source, the track
you listened to last time is resumed.
6 Set the alarm volume.
6
ENTER
PRESET
To have the alarm sound at the last
volume level you used, select “---”.
Once you have set the alarm volume,
the alarm is set and the alarm indicator
(
) lights up.
y
• While setting the alarm, press RETURN to
return to the previous setting.
• To cancel without setting the alarm, press
ALARM before step 6 is completed.
X Switching the alarm on/off
Switch on/off the alarm function.
ALARM
y
When the alarm is on, the alarm indicator
(
) lights up and alarm time is displayed
for a while.
Operations during playing back alarm sound
At the set time, alarm sound plays back. During playback, operations below are available.
Note
If source cannot be played back at the alarm time (ex. iPod is not set), beep sound is played back.
X Using the snooze function
Press SNOOZE/SLEEP.
VOLUME
The alarm sound stops and resumes after
5 minutes.
y
SNOOZE / SLEEP
16 En
• When SRC+BEEP is set, press SNOOZE/
SLEEP to stop the beep sound. press
SNOOZE/SLEEP again to stop the source.
The beep sounds 5 minutes after the source
stopped. The source fades in 1 minute before
the beep sounds.
• When the snooze function is activated, alarm
indicator flashes.
SHUFFLE/REPEAT PLAYBACK
English
X Stopping the alarm
Press ALARM or
.
y
• Unless you stop the alarm, the alarm stops
after 60 minutes automatically.
• The alarm function turns off when you stop
the alarm, but settings such as the alarm time
are saved for convenient use next time. To set
the alarm again, press ALARM.
ALARM
SHUFFLE/REPEAT PLAYBACK
Shuffle playback
Repeat playback
Press repeatedly
Press repeatedly
Remote control
Remote control
CD/USB
SHUFFLE FOLDER
(Shuffle all songs in the
folder)
SHUFFLE ALL
(All shuffle)
SHUFFLE OFF
(Shuffle Off)
iPod
SHUFFLE SONGS
(Shuffle songs)
SHUFFLE ALBUMS
(Shuffle albums)
SHUFFLE OFF
(Shuffle Off)
CD/USB
REPEAT ONE
(Single repeat)
REPEAT FOLDER
(Repeat all songs in the
folder)
REPEAT ALL
(All repeat)
REPEAT OFF
(Repeat Off)
iPod
REPEAT ONE
(Single repeat)
REPEAT ALL
(All repeat)
REPEAT OFF
(Repeat Off)
y
•
•
•
•
You cannot set SHUFFLE ALBUMS when you use an iPod touch or iPhone.
When source contains folders, folder shuffle/repeat can be selected.
For some iPod models, the shuffle and repeat functions may not be displayed or supported.
When iPod is played back, the setting order of shuffle and repeat depends on the iPod model.
17 En
LISTENING TO EXTERNAL SOURCE
1
1 Connect your portable audio
device to AUX using a
commercially available 3.5 mm
(1/8 in) mini plug cable.
2
SOURCE
Note
Turn down the volume of this unit and your
portable audio device before connection.
2 Set SOURCE to AUX.
Rear Panel
3 Start playback on the connected
portable audio device.
4 Adjust the volume level of the
unit and the portable audio
device.
USING SLEEP FUNCTION
You can set the time to turn off the system automatically.
1
2
Press and hold
VOLUME
PRESET
ENTER
1 Press and hold SNOOZE/
SLEEP for more than 2 seconds.
2 Select the sleep time from 30,
60, 90,120 and SLEEP OFF.
When the time is set, the sleep
function is set to on, and the SLEEP
indicator lights up.
SNOOZE / SLEEP
y
To exit without changing the current
setting, press SNOOZE/SLEEP.
18 En
English
USING OPTION MENU
The option menu appears on the front panel display by pressing OPTION on the remote control. You can set
various useful functions with option menu.
Option menu
Parameter or control range
Reference page
PRESET DELETE
(Displays only when the input source is set to DAB/FM.)
14, 20
DAB CLEAR*1
(Displays only when the input source is set to DAB.)
20
INIT SCAN
(Displays only when the input source is set to DAB.)
20
TUNE AID
(Displays only when the input source is set to DAB.)
20
DIMMER
DIMMER OFF (brightest)/DIMMER 1/DIMMER 2 (darkest)
This page
TREBLE
-10 dB to +10 dB
This page
BASS
-10 dB to +10 dB
This page
AUTO POWER
OFF
TIME OFF/ TIME 8H/ TIME 4H
AUTO POWER OFF sets the system to system off or power save mode
whenever no operation is performed for a preset amount of time.
This page
*1 When the input source is set to DAB, and if the unit cannot receive any DAB stations, these setup menus do
not appear.
X Operation procedure
For DAB CLEAR, INIT SCAN and TUNE AID, see page 20.
1
1 Press OPTION.
3
2
MENU
ENTER
OPTION
ENTER
2 Select desired option menu with
S/T.
3 Confirm with ENTER.
Remote control
4
Remote control
Remote control
4 Change the settings with S/T.
5 Complete the setting with ENTER.
6
5
MENU
ENTER
ENTER
OPTION
To set additional items, repeat steps 2 to 5.
6 Exit option menu with OPTION.
y
Remote control
Remote control
Remote control
To cancel without changing the settings, press
OPTION before step 5 is completed.
X Setting dimmer/tone
DIMMER: Changes the brightness of the front panel display.
TREBLE*: Adjusts the high frequency response.
BASS*: Adjusts the low frequency response.
* Also effective when you are using headphones.
19 En
USING OPTION MENU
Using DAB option menu
X Performing DAB CLEAR and INIT SCAN
1
1 Press OPTION.
3
2
MENU
ENTER
OPTION
ENTER
2 Select desired option menu with
S/T.
3 Confirm with ENTER.
Remote control
Remote control
4
Remote control
4 “Press ENTER” appears.
Press ENTER to perform*.
5
5 Exit option menu with OPTION.
OPTION
ENTER
Remote control
Remote control
DAB CLEAR: Deletes all DAB station information and preset settings stored in the unit. After DAB CLEAR is
complete, the unit moves to the INIT SCAN functions automatically. Note that once DAB CLEAR is
performed, the deleted information and preset settings cannot be restored.
INIT SCAN: Performs the initial scan manually. Each time you perform INIT SCAN, the newly received
stations are added to the previously received stations.
* After performing INIT SCAN, the unit airs the first station as stored in station.
X Using TUNE AID
1
1 Press OPTION.
3
2
MENU
Remote control
4
2 Select TUNE AID.
ENTER
OPTION
ENTER
Remote control
Remote control
6
5
MENU
ENTER
Remote control
ENTER
Remote control
3 Confirm with ENTER.
OPTION
4 Switch the channel label.
5 Exit TUNE AID.
6 Exit option menu with OPTION.
Remote control
TUNE AID: Measures reception strength of the received DAB signal (from 0 (none) to 100 (best)). Adjust the
DAB/FM antenna to find the best position to receive the DAB signal.
y
To check the frequency corresponding to the channel label, refer to “DAB frequency information” on page 13.
20 En
ADDITIONAL INFORMATION
English
TROUBLESHOOTING
In case of a problem with the unit, check the following list first. If you cannot solve your problem with the
suggested solutions or if your problem is not listed below, turn off and unplug the unit, and consult the nearest
authorized Yamaha dealer or service center.
General
Problem
The speakers make no
sound.
Cause
Solution
The volume may be set to the minimum level. Adjust the volume level.
The source may be incorrect.
Select the correct source.
Headphones are connected.
Remove the headphones.
Sound is cracked/distorted
or there is abnormal noise.
Input source volume is excessive, or
volume of this unit is excessive
(especially Bass).
Adjust volume with VOLUME, or adjust
Bass with the option menu (☞ P. 19).
The unit does not operate
properly.
The unit may have received a strong
electrical shock such as lightning or
excessive static electricity, or power
supply may have dropped.
Set the system to off, and disconnect the
power cable. Wait about 30 seconds,
reconnect the power cable, and turn on the
system.
The system turns on but
immediately shuts off.
The unit may be placed too close to the
A digital or high-frequency
equipment produces noises. digital or high-frequency equipment.
Place the unit farther away from the
equipment.
The clock setting has been
cleared.
Plug the power cable into the wall outlet
firmly, and set the clock again (☞ P. 7).
The unit is left more than five minutes
after you disconnect the power cable
from the wall outlet.
When it is time for the alarm The alarm source you have selected is
not connected or inserted.
to sound, only a beep is
heard; no music is heard.
The alarm type is set to BEEP.
If you have selected iPod or USB, make
sure the device is connected. If you have
selected CD, make sure the CD is inserted.
Set the alarm type to SRC+BEEP or
SOURCE (☞ P. 15).
Clock flashes and the unit
cannot be operated.
CLOCK on the rear panel is set to SET, Set CLOCK on the rear panel to ON
and this unit is in clock setting mode.
(☞ P. 7).
The system is suddenly
turned off.
The automatic system off function turned This unit automatically turns off the system
the unit off.
60 minutes after USB device or CD
playback is stopped.
The sleep (☞ P. 18) may be set.
Turn on the system and play the source again.
The AUTO POWER OFF function is
triggered.
Setting AUTO POWER OFF to TIME OFF
enables to play continuously (☞ P. 19).
21 En
TROUBLESHOOTING
DAB reception
Problem
Cannot tune into any DAB
stations.
The initial scan operations
are not successful and “Not
found” appears on the DAB
information display.
Cause
Perform the initial scan operations
(☞ P. 10).
There is no DAB coverage in your area.
Check with your dealer or WorldDMB
Online at “http://www.worlddab.org” for a
listing of the DAB coverage in your area.
The DAB signals are too weak.
Change the height, direction, or placement
of the antenna.
The DAB signals are too weak.
There is no DAB coverage in your area.
The DAB station reception is The DAB signals are too weak.
weak.
There is noise interference
(e.g. hiss, crackle or jitter).
Solution
The initial scan operations were not
performed.
Check with your dealer or WorldDMB
Online at “http://www.worlddab.org” for a
listing of the DAB coverage in your area.
Change the height, direction, or placement
of the antenna.
The antenna needs to be repositioned.
The DAB signals are too weak.
The DAB station information The DAB station may be temporarily out Contact the DAB broadcaster.
of service, or the DAB station
does not appear or is
information is not provided by the DAB
inaccurate.
broadcaster.
FM reception
Problem
Too much noise during
stereo broadcast.
Cause
The antenna may be connected
improperly.
Solution
Make sure the antenna is connected
properly (☞ P. 4).
The radio station you selected may be far Try manual tuning to improve the signal
from your area, or the radio wave
quality (☞ P. 13) or use a multi-channel
reception is weak in your area.
outdoor antenna.
Even with an outdoor antenna, Multipath reflection or other radio
radio wave reception is weak. interferences may have occurred.
(Sound is distorted.)
22 En
Change the height, direction, or placement
of the antenna.
TROUBLESHOOTING
English
iPod
Note
In case of a transmission error without a status message appearing in the front panel of this unit, check the
connection to your iPod (☞ P. 6).
Status message
Cause
Remedy
iPod Connecting
iPod Charging
This unit is in the middle of recognizing If the message continues to appear in the
the connection with your iPod.
front panel display and playback does not
start, connect the iPod again (☞ P. 6).
Unknown iPod
There is a problem with the signal path
from your iPod to this unit.
Connect the iPod again (☞ P. 6).
The iPod being used is not supported by Only iPod classic, iPod nano (2nd
this unit.
generation and later), iPod touch and iPhone
are supported.
iPod
This unit has recognized your iPod;
however, it cannot obtain information
such as elapsed time.
iPod Unplugged
Your iPod was removed from the iPod dock. Station your iPod back in the iPod dock (☞ P. 6).
Over Current
The iPod being used is not supported by Disconnect the iPod and then turn the
this unit.
system off and on again. Then connect
supported iPod again (☞ P. 26).
The iPod is connected at an angle.
Problem
No sound
Cause
Set the iPod firmly.
Headphones are connected.
Remove the headphones.
The iPod software version has not been
updated.
Download the latest iTunes software to
update the iPod software version to the
latest.
The iPod does not charge up. The iPod is set in the iPod dock
Suddenly the music being
played back is canceled and
another track starts playing
without performing any
operation.
Solution
The iPod is not set in the iPod dock
firmly.
improperly.
Remove the iPod from the unit, and then set
it in the iPod dock again (☞ P. 6).
The system is set to power save mode
(☞ P. 2).
Set CLOCK to ON on the rear panel to
cancel power save mode (☞ P. 4).
The iPod’s Shake to Shuffle function is
turned on.
Turn off the Shake to Shuffle function in
the iPod’s settings.
Remote control
Problem
Cause
The remote control does not The remote control may be operated
outside its operation range.
work properly.
Solution
For information on the remote control
operation range, refer to “Using the remote
control” (☞ P. 5).
The remote control sensor on the unit
may be exposed to direct sunlight or
lighting (inverted fluorescent lamps).
Change the lighting or orientation of the
unit.
The battery may be worn out.
Replace the battery with a new one.
There are obstacles between the sensor
of the unit and the remote control.
Remove the obstacles.
23 En
TROUBLESHOOTING
Disc playback
Problem
Cause
Solution
Disc cannot be inserted. The system is set to power save mode (☞ P. 2). Set CLOCK to ON on the rear panel to
cancel power save mode (☞ P. 4).
Some button operations The disc loaded into the unit may not be
compatible.
do not work.
Use a disc supported by the unit (☞ P. 25).
Playback does not start
immediately after
pressing
.
The disc may be dirty.
Wipe the disc clean.
The disc loaded into the unit may not be
compatible.
Use a disc supported by the unit (☞ P. 25).
If the unit was moved from a cold to warm
Wait for an hour or two until the unit adjusts
place, condensation may have formed on the to the room temperature, and try again.
disc reading lens.
“No Disc” or “Unknown The disc loaded into the unit may not be
Disc” is displayed in the compatible.
front panel display after The disc may be dirty.
loading a disc.
The disc is loaded back to front.
Use a disc supported by the unit (☞ P. 25).
Wipe the disc clean.
Insert a disc facing the label side to near side.
The disc does not contain playable files.
Use a disc contains playable files (☞ P. 25).
An error occurs in the unit.
Unload the disc with
.
USB device playback
Note
In case of a transmission error without a status message appearing in the front panel of this unit, check the
connection to the USB device (☞ P. 8).
Status message
Cause
Remedy
USB Unplugged
The USB device is not connected firmly.
Unknown USB
The connected USB device is not playable on Connect playable USB device (☞ P. 25).
this unit.
Connect the USB device again (☞ P. 8).
The file name is too long.
The file name should be no more than 250
characters.
Over Current
The USB device is connected at an angle.
Disconnect the USB device and then turn the
system off and on again. Then connect
playable USB device again (☞ P. 25).
No Files
The USB device does not contain playable
files.
Use a USB device contains playable files
(☞ P. 25).
An incompatible USB device is connected to Turn off the system and reconnect the USB
the unit.
device to the unit. If it does not resolve the
problem, the USB device is not playable on
the unit.
USB Time Out
Problem
The number of files/folders exceeds the
limit.
Cause
MP3/WMA file in the USB The USB device is not recognized.
device does not play.
Reduce the number of files/folders; refer to
the limitations noted in this manual (☞ P. 25).
Solution
Turn off the system and reconnect the USB
device to the unit.
Connect an AC adapter if supplied with the device.
Format the USB device and copy the files again.
If the solutions above do not resolve the problem,
the USB device is not playable on the unit.
24 En
English
NOTES ON DISCS AND USB DEVICES
Disc information
This unit is designed for use with audio CD, CD-R*1,
and CD-RW*1 with the logos followings.
• If a disc becomes
dirty, wipe it with a
clean, dry cloth from
the center out to the
edge. Do not use
record cleaner or
paint thinner.
• To avoid
malfunction, do not
use a commercially
available lens
cleaner.
USB device information
*1
ISO 9660
y
This unit can play back discs bearing any of the logo marks
above. A disc logo mark is printed on the disc and the disc
jacket.
Notes
• Do not load any other type of disc into this unit. Doing so
may damage this unit.
• CD-R/RW cannot be played back unless finalized.
• Some discs cannot be played back depending on the disc
characteristics or recording conditions.
• Do not use any non-standard shaped discs such as a heartshaped disc.
• Do not use discs with many scratches on their surface.
Handling a disc
• Do not touch the surface of
the disc. Hold a disc by its
edge (and the center hole).
• Do not use a pencil or
pointed marker to write on
the disc.
• Do not put a tape, seal, glue, etc., on a disc.
• Do not use a protective cover to prevent scratches.
• Do not load more than one disc into this unit at one time.
This can cause damage to both this unit and the discs.
• Do not insert any foreign objects into the disc slot.
• Do not load a cracked, warped, or glued disc.
• Do not expose a disc
to direct sunlight,
Caution
high temperature,
high humidity, or a
lot of dust.
This unit supports USB mass storage class devices
(e.g., flash memories or portable audio players) using
FAT16 or FAT32 format.
Notes
• Some devices may not work properly even if they meet the
requirements.
• Do not connect devices other than USB mass storage class
devices (such as USB chargers or USB hubs), PCs, card
readers, an external HDD, etc.
• Yamaha will not be held responsible for any damage to or
data loss on the USB device occurring while the device is
connected to this unit.
• Playability of and power supply to all kind of USB devices
are not guaranteed.
• USB devices that use encryption cannot be used.
About MP3 or WMA files
Notes
• The unit can play back:
File
MP3
WMA
Bitrate (kbps)
8 - 320*2
16 - 320*2
Sampling
frequency (kHz)
16 - 48
22.05 - 48
*2 Both constant and variable bitrates are supported.
• The maximum numbers of files/folders that can be
displayed on the unit are as follows.
Data CD
USB
Maximum total number of file*3
512
9999
Maximum folder number*3
255
999
Maximum file number per folder
511
255
*3
The root is counted as one of the folders.
• Copyright-protected files cannot be played back.
25 En
SPECIFICATIONS
X PLAYER SECTION
LASER SAFETY
iPod (Digital connection)
This unit employs a laser. Due to possible eye injury, only a
qualified service person should remove the cover or attempt
to service this device.
• Made for ...... iPod touch (1st, 2nd, 3rd, and 4th generation)
iPod classic
iPod nano (2nd, 3rd, 4th, 5th, and 6th generation)
iPhone 4
iPhone 3GS
iPhone 3G
iPhone
CD
• Media ........................................................... CD, CD-R/RW
• Audio format ................................. Audio CD, MP3, WMA
Laser
• Type .............................Semiconductor laser GaAs/GaAlAs
• Wave length .............................................................790 nm
• Output Power .............................................................7 mW
USB
• Audio format ....................................................MP3, WMA
AUX
• Input connector ........... 3.5 mm (1/8 in) STEREO mini Jack
X AMPLIFIER SECTION
• Maximum output power ................................. 15 W + 15 W
(6 Ω 1 kHz, 10% THD)
• Headphones ............................ 3.5 mm STEREO mini Jack
(Adaptive Impedance 16 to 32 Ω)
X TUNER SECTION
• Tuning range
FM .................................................. 87.50 to 108.00 MHz
DAB/DAB+........................... 174 to 240 MHz (Band III)
X GENERAL
•
•
•
•
•
Power Supply............................................AC 230 V, 50 Hz
Power consumption ..................................................... 23 W
System off consumption ............................................. 2.7 W
Power save consumption ............................................ 0.2 W
Dimensions (W × H × D) ... W457 × H180.5 × D177.5 mm
(W18 × H7 1/8 × D7)
• Weight ...................................................... 5.1 kg (11.2 lbs.)
Specifications are subject to change without notice.
DANGER
This unit emits visible laser radiation when open. Avoid
direct eye exposure to beam. When this unit is plugged into
the wall outlet, do not place your eyes close to the opening of
the disc tray and other openings to look into inside.
The laser component in this product is capable of
emitting radiation exceeding the limit for Class 1.
iPod, iPhone
“Made for iPod,” and “Made for iPhone” mean that an
electronic accessory has been designed to connect
specifically to iPod, or iPhone, respectively, and has been
certified by the developer to meet Apple performance
standards.
Apple is not responsible for the operation of this device or its
compliance with safety and regulatory standards.
Please note that the use of this accessory with iPod or iPhone
may affect wireless performance.
iPhone, iPod, iPod classic, iPod nano, iPod shuffle, and iPod
touch are trademarks of Apple Inc., registered in the U.S. and
other countries.
BATTERY CAUTIONS
• If the battery grows old, the effective operation range of the
remote control decreases considerably. If this happens,
replace the battery with new one as soon as possible.
• Exhausted battery may leak. If the battery have leaked,
dispose of it immediately. Avoid touching the leaked
material or letting it come into contact with clothing, etc.
Clean the battery compartment thoroughly before installing
a new battery.
• Keep the battery away from children. If the battery is
accidentally swallowed, contact your doctor immediately.
• When not planning to use the remote control for long
periods of time, remove the battery from the remote
control.
• Do not charge or disassemble the supplied battery.
This unit supports DAB/DAB+ tuning.
26 En
English
Information for Users on Collection and Disposal of Old Equipment
and Used Batteries
These symbols on the products, packaging, and/or accompanying documents mean that used electrical and
electronic products and batteries should not be mixed with general household waste.
For proper treatment, recovery and recycling of old products and used batteries, please take them to
applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC
and 2006/66/EC.
By disposing of these products and batteries correctly, you will help to save valuable resources and prevent
any potential negative effects on human health and the environment which could otherwise arise from
inappropriate waste handling.
For more information about collection and recycling of old products and batteries, please contact your local
municipality, your waste disposal service or the point of sale where you purchased the items.
[Information on Disposal in other Countries outside the European Union]
These symbols are only valid in the European Union. If you wish to discard these items, please contact your
local authorities or dealer and ask for the correct method of disposal.
Note for the battery symbol (bottom two symbol examples):
This symbol might be used in combination with a chemical symbol. In this case it complies with the
requirement set by the Directive for the chemical involved.
27 En
Australia model
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may result in
hazardous radiation exposure.
U.K. model
• The name plate is located on the back of the unit.
28 En
English
■ For U.K. customers
If the socket outlets in the home are not suitable for the plug
supplied with this appliance, it should be cut off and an
appropriate 3 pin plug fitted. For details, refer to the
instructions described below.
Note
The plug severed from the mains lead must be destroyed, as a
plug with bared flexible cord is hazardous if engaged in a live
socket outlet.
■ Special Instructions for U.K.
Model
IMPORTANT
THE WIRES IN MAINS LEAD ARE COLOURED
IN ACCORDANCE WITH THE FOLLOWING
CODE:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured
markings identifying the terminals in your plug,
proceed as follows:
The wire which is coloured BLUE must be connected
to the terminal which is marked with the letter N or
coloured BLACK. The wire which is coloured
BROWN must be connected to the terminal which is
marked with the letter L or coloured RED.
Make sure that neither core is connected to the earth
terminal of the three pin plug.
29 En
© 2011 Yamaha Corporation
Printed in Malaysia WY87350