Yamaha EMX620 Owner`s manual

Owner’s Manual
1
2
HIGH
3
HIGH
4
HIGH
5
HIGH
SEE REAR PANEL CAUTION
6
HIGH
POWER
HIGH
VOCAL
–15
+15
LOW
–15
+15
LOW
–15
+15
MONI
–15
+15
MONI
0
EFFECT
0
LEVEL
10
10
–15
+15
LOW
–15
+15
MONI
0
EFFECT
0
LEVEL
10
10
–15
+15
LOW
–15
+15
MONI
0
EFFECT
10
0
LEVEL
10
–15
+15
LOW
–15
+15
MONI
0
EFFECT
0
LEVEL
10
10
–15
+15
LOW
PHANTOM
L HALL
–15
+15
ON
OFF
S HALL
MONI
0
EFFECT
0
LEVEL
10
10
LIMITER
0
EFFECT
0
LEVEL
10
10
ON
DIGITAL
EFFECT
–12
•
6
•
0
•
6
•
+12
–12
•
6
•
0
•
6
•
+12
125
0
10
PAD
0
10
PAD
0
10
PAD
0
10
0
10
0
3
4
Hi-Z
Hi-Z
Hi-Z
Hi-Z
5
LINE
1
Lo-Z
Lo-Z
10
EFFECT RTN
2
500
1k
2k
4k
8k
0
10
EFFECT RTN
10
PAD
1
Lo-Z
0
250
+6
+3
0
–5
–10
6
EFFECT
INST
EFFECT OUT
0
10
0
AUX IN
10
0
TAPE IN
10
0
MASTER
10
MASTER
MAIN
MONI
MONITOR
1
TAPE
IN
REC
OUT
1
1
2
2
Lo-Z
LINE
2
INST
FOOT SW
MAIN PHONES
AUX IN
2
INPUT
TO MAIN
Keep This Manual For Future Reference.
OUTPUT
E
FCC INFORMATION (U.S.A.)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST
be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA.
3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with
these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with
other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may
cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all
installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the
problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on
different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in
is 300 ohm ribbon lead, change the lead-in to coaxial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer
authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service
Division, 6600 Orangethorpe Ave, Buena Park, CA 90620
The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.
WARNING: THIS APPARATUS MUST BE EARTHED
IMPORTANT
THE WIRES IN THIS MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:
GREEN-AND-YELLOW :
EARTH
BLUE :
NEUTRAL
BROWN :
LIVE
As the colours of the wires in the mains lead of this apparatus may
not correspond with the coloured markings identifying the terminals in
your plug, proceed as follows:
The wire which is coloured GREEN and YELLOW must be
connected to the terminal in the plug which is marked by the letter E
or by the safety earth symbol
or coloured GREEN and YELLOW.
The wire which is coloured BLUE must be connected to the terminal
which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the
terminal which is marked with the letter L or coloured RED.
* This applies only to products distributed by YAMAHA KEMBLE
MUSIC (U.K.) LTD.
Important
3
Important
Read the following before operating the EMX620
Warnings
• Do not allow water to enter this unit or allow the unit to become wet. Fire or electrical shock
may result.
• Connect this unit’s power cord only to an AC outlet of the type stated in this Owner’s Manual
or as marked on the unit. Failure to do so is a fire and electrical shock hazard.
• Do not scratch, bend, twist, pull, or heat the power cord. A damaged power cord is a fire and
electrical shock hazard.
• Do not place heavy objects, including this unit, on top of the power cord. A damaged power
cord is a fire and electrical shock hazard. In particular, be careful not to place heavy objects on
a power cord covered by a carpet.
• If you notice any abnormality, such as smoke, odor, or noise, or if a foreign object or liquid
gets inside the unit, turn it off immediately. Remove the power cord from the AC outlet.
Consult your dealer for repair. Using the unit in this condition is a fire and electrical shock
hazard.
• Should this unit be dropped or the cabinet be damaged, turn the power switch off, remove the
power plug from the AC outlet, and contact your dealer. If you continue using the unit
without heeding this instruction, fire or electrical shock may result.
• If the power cord is damaged (i.e., cut or a bare wire is exposed), ask your dealer for a
replacement. Using the unit with a damaged power cord is a fire and electrical shock hazard.
• Do not remove the unit’s cover. You could receive an electrical shock. If you think internal
inspection, maintenance, or repair is necessary, contact your dealer.
• Do not modify the unit. Doing so is a fire and electrical shock hazard.
Cautions
• Allow enough free space around the unit for normal ventilation. This should be: 30 cm at the
sides, 30 cm behind, and 40 cm above.
These distances should also be adopted when rack-mounting the unit. For normal ventilation
during use, remove the rear of the rack or open a ventilation hole.
If the airflow is not adequate, the unit will heat up inside and may cause a fire.
• This unit has ventilation holes at the front, rear and sides to prevent the internal temperature
rising too high. Do not block them. Blocked ventilation holes are a fire hazard.
• Clean phone plugs before plugging them into the speaker jacks of this unit. Dirty contacts
may generate heat.
• Use only designated speaker cables to connect speakers to the amplifier outputs. Using other
types of cable is a fire hazard.
• Hold the power cord plug when disconnecting it from an AC outlet. Never pull the cord. A
damaged power cord is a potential fire and electrical shock hazard.
• Do not touch the power plug with wet hands. Doing so is a potential electrical shock hazard.
EMX620—Owner’s Manual
4
Important
Operating Notes
• Using a mobile telephone near this unit may induce noise. If noise occurs, use the telephone
away from the unit.
• XLR-type connectors are wired as follows:
pin 1: ground, pin 2: hot (+), and pin 3: cold (–).
• Do not set all equalizer controls and faders to maximum. Doing so may cause oscillation
depending on the condition of the connected unit and speakers, and may damage the
speakers.
• The performance of components with moving contacts, such switches, rotary controls, faders,
and connectors, deteriorates over time. The rate of deterioration depends on the operating
environment and is unavoidable. Consult your dealer about replacing defective components.
EMX620—Owner’s Manual
Introduction
5
Introduction
Thank you for purchasing the Yamaha EMX620 Powered Mixer. In order to take full
advantage of the EMX620 and enjoy long and trouble-free operation, read this owner’s
manual carefully, and keep it in a safe place for future reference.
Features
• The EMX620’s six input channels support a wide
range of audio sources, including microphones,
instruments, and line-level devices. Input channels 1 through 4 feature lo- and hi-impedance
balanced inputs, with +15 V phantom powering
for use with condenser-type microphones on the
lo inputs, input channel 5 features two line-level
inputs, while input channel 6 features two
hi-impedance inputs for connecting instruments
such as electric-acoustic guitar and electric bass
directly.
• The built-in power amplifier offers a maximum
output of 200 W with a 4Ω speaker system,
135 W with an 8Ω speaker system, and a limiter
circuit prevents sounds distortion and speaker
damage.
• The 7-band graphic equalizer on the main output
allows you to tailor the sound for each particular
venue and reduce the risk of feedback by attenuating troublesome frequencies.
Contents
Front & Rear Panels.................................. 6
Control Panel ............................................ 6
Input/Output Panel ................................... 9
Rear Panel ................................................ 11
Hookup Example...................................... 12
Basic Operation....................................... 13
Connecting Sources ................................. 13
Monitoring............................................... 13
Using the Built-in Effects........................... 13
Troubleshooting...................................... 14
Specifications .......................................... 15
General Specifications .............................. 15
Input Specifications .................................. 16
Output Specifications ............................... 16
Dimensions .............................................. 16
Block & Level Diagrams............................ 17
• Also built-in is a digital effects processor, offering
three different programs for adding reverberation or ambiance to vocal or instrument sounds,
and remote on/off control using an optional
footswitch.
• External effects can be patched into the system
via the EFFECT OUT and AUX IN jacks, with
effects return level control.
• Separate outputs are provided for connecting
powered monitor speakers, headphones, or a stereo recorder (cassette, DAT, or MD).
EMX620—Owner’s Manual
6
Front & Rear Panels
Front & Rear Panels
Control Panel
■ Channel Section
The channel controls are used to set the EQ,
MONI and EFFECT send levels, channel LEVEL,
and PAD for each channel.
1
HIGH
1
–15
+15
LOW
–15
+15
MONI
2
0
EFFECT
10
0
LEVEL
10
0
10
4
PAD
1
1 HIGH & LOW EQ controls
The 2-band equalizer allows you to boost or cut
the low or high frequency range for each channel.
The frequency response is flat when the controls
are in the center (▼) position. Rotating clockwise
boosts frequencies, rotating counterclockwise
cuts them.
The center frequencies are as follows:
HIGH: 10 kHz ±15 dB shelving type
LOW:
100 Hz ±15 dB shelving type
B MONI control
The MONI control determines the level of the
input signal that is fed to the MONI bus and subsequently the MONITOR OUTPUT jack.
The MONI control is not affected by the channel’s LEVEL control, since the MONI signal is
sourced before that control.
EMX620—Owner’s Manual
The EFFECT control determines the level of the
input signal that is fed to the EFFECT bus and
subsequently the onboard effects processor and
EFFECT OUT jack.
EFFECT bus signals are fed simultaneously to the
onboard effects processor and the EFFECT OUT
jack for use with external effects processors.
The EFFECT control is affected by the channel’s
LEVEL control, since the EFFECT signal is
sourced after that control. To send a channel signal to the EFFECT bus, both the EFFECT and
LEVEL controls must be turned up.
D LEVEL control
3
5
C EFFECT control
The LEVEL control determines the level of the
input signal that is fed to the MAIN bus, MAIN
output section, and internal power amplifier.
E PAD switch (1–4 only)
The PAD switch attenuates the input signal by
30 dB. When connecting a line-level source to
inputs 1 through 4, or if a microphone signal is
distorted, use the PAD switch to attenuate the
input signal.
7
Control Panel
■ DIGITAL EFFECT Section
■ MAIN Section
The DIGITAL EFFECT section is used to turn the
built-in digital effects processor on and off and
select effects programs.
The MAIN section is used to set the MAIN MASTER level, 7-band graphic equalizer, AUX IN and
TAPE IN levels, and MAIN EFFECT RTN level. It
also contains the LIMITER indicator and main
output level meter.
VOCAL
L HALL
8
6
LIMITER
D
S HALL
ON
7
–12
•
6
•
0
•
6
•
+12
DIGITAL
EFFECT
–12
•
6
•
0
•
6
•
+12
125
0
250
10
EFFECT RTN
500
1k
0
2k
10
4k
8k
0
AUX IN
+6
+3
0
–5
–10
10
0
C
10
TAPE IN
MASTER
A
B
MAIN
EFFECT
F VOCAL, L. HALL, S. HALL switches
These switches are used to select the effects programs: VOCAL, L. HALL (large hall), S. HALL
(small hall).
G DIGITAL EFFECT ON switch & indicator
The DIGITAL EFFECT ON switch is used to turn
the built-in digital effects processor on and off.
The indicator lights up when the processor is on.
When the processor is on, its output is fed to the
MAIN and MONI buses via the MAIN EFFECT
RTN and MONI EFFECT RTN controls respectively.
The effects processor can also be turned on and
off remotely by connecting an optional footswitch to the FOOT SW jack.
9
0
H Graphic equalizer
The 7-band graphic equalizer is used to boost or
cut certain frequencies of the MAIN output signal by up to ±12 dB. It affects the MAIN OUTPUT signal, the speaker outputs, and the
PHONES.
I EFFECT RTN control
The MAIN EFFECT RTN control determines the
level of the signal from the built-in digital effects
processor that is fed to the MAIN bus and subsequently the MAIN outputs.
J AUX IN control
The AUX IN control determines the level of the
AUX IN signal that is fed to the MAIN bus and
subsequently the MAIN outputs.
K TAPE IN
The TAPE IN control determines the level of the
TAPE IN signal that is fed to the MAIN bus and
subsequently the MAIN outputs.
L MASTER control
The MAIN MASTER control determines the output level of the MAIN OUT, speaker outputs, and
PHONES.
M Level meter
The 5-LED meter displays the level of the MAIN
output signal.
EMX620—Owner’s Manual
8
Front & Rear Panels
N LIMITER indicator
The LIMITER indicator lights up when the limiter circuit, which is designed to protect the internal power amplifier against excessive input
signals and load mismatches, activates.
If the LIMITER indicator lights up, back off the
MAIN MASTER level control, or the appropriate
channel LEVEL control a little. If the indicator
remains lit, make sure that the impedance of the
connected speaker system is correct.
The MONI section is used to set the MONI
MASTER level and MONI EFFECT RTN level.
E
10
EFFECT RTN
F
0
10
MASTER
MONI
O EFFECT RTN
The MONI EFFECT RTN control determines the
level of the signal from the built-in digital effects
processor that is fed to the MONI bus and subsequently the MONITOR OUTPUT.
P MASTER control
The MONI MASTER control determines the output level of the MONITOR OUTPUT.
EMX620—Owner’s Manual
POWER
G
PHANTOM
ON
OFF
H
Q POWER indicator
■ MONI Section
0
■ POWER Indicator, PHANTOM
Switch & Indicator
The POWER indicator lights up when the
EMX620 is powered up ready for use.
R PHANTOM switch
The PHANTOM switch is used to turn on and off
the +15 V phantom power for the Lo-Z
XLR-type inputs on input channels 1 through 4.
Input/Output Panel
9
Input/Output Panel
A
4
Hi-Z
Hi-Z
Hi-Z
Hi-Z
LINE
1
Lo-Z
Lo-Z
Lo-Z
INST
MONITOR
EFFECT OUT
1
TAPE
IN
1
1
2
2
Lo-Z
LINE
2
INST
FOOT SW
MAIN PHONES
AUX IN
2
INPUT
TO MAIN
1
2
3
1 Hi-Z, Lo-Z (inputs 1–4)
5
6
OUTPUT
78 9 0
C INST 1 & 2 (input 6)
These are the input connectors for input channels 1 through 4. Both the Hi-Z and Lo-Z input
can be used with microphones and, by using the
PAD switch, can also be used with line-level
sources, such as synthesizers and drum machines.
Switchable +15 V phantom power is available to
the Lo-Z XLR-type input for use with condenser-type microphones.
Both the Hi-Z and Lo-Z inputs are balanced.
Pin connections are as follows.
Lo-Z (XLR-type)
REC
OUT
Hi-Z (TRS phone jack)
Pin 1: ground
Sleeve: ground
Pin 2: hot (+)
Ring: cold (–)
Pin 3: cold (–)
Tip: hot (+)
S
R T
These two phone jacks are the input connectors
for input channel 6. They are unbalanced, can be
used simultaneously, and their high input impedance makes them ideal for use with instruments
such as electric-acoustic guitar and electric bass.
They can also be used with line-level sources,
such as synthesizers and drum machines.
D EFFECT OUT jack
The EFFECT OUT phone jack outputs the signal
from the EFFECT bus and can be connected to
the input of an external effects processor.
E FOOT SW jack
The FOOT SW jack is used to connect an
optional footswitch, such as the Yamaha FC5,
which can be used to turn the built-in digital
effects processor on and off. The DIGITAL
EFFECT ON switch must be in the ON position
in order to use the footswitch.
F AUX IN—INPUT TO MAIN jack
+ - GND
GND -
+
Note: The Lo-Z and Hi-Z input of each channel
cannot be used simultaneously. Use the input
appropriate for the source.
Note: Since phantom power is turned on and
off for inputs channels 1 through 4 simultaneously, input devices that do not require it
should be connected to the Hi-Z input when
phantom power is used.
B LINE 1 & 2 (input 5)
These two phone jacks are the input connectors
for input channel 5. They are unbalanced, can be
used simultaneously, and are appropriate for use
with line-level sources, such as synthesizers and
drum machines.
The AUX IN—INPUT TO MAIN phone jack is
used to feed signals from an external source to
the MAIN bus and can be connected to the output of an external effects processor, for example.
G TAPE IN—INPUT TO MAIN jacks
The TAPE IN—INPUT TO MAIN phono jacks
are used to feed signals from an external source to
the MAIN bus and can be connected to the stereo
outputs of a cassette, DAT, or MD deck.
H REC OUT—OUTPUT jacks
The REC OUT—OUTPUT phono jacks output
the MAIN bus signal prior to the 7-band graphic
equalizer and MASTER level control, and can be
connected to the stereo inputs of a cassette, DAT,
or MD deck for recording.
EMX620—Owner’s Manual
10
Front & Rear Panels
I MAIN—OUTPUT jack
The MAIN—OUTPUT jack outputs the MAIN
bus signal after the 7-band graphic equalizer and
MASTER level control, and can be connected to
the input of a larger mixer, or a more powerful
amplifier, for example.
J PHONES—OUTPUT jack
The PHONES—OUTPUT jack outputs the
MAIN bus signal after the 7-band graphic equalizer and MASTER level control, and can be connected to a pair of stereo headphones for
personal monitoring.
K MONITOR—OUTPUT
The MONITOR—OUTPUT phone jack outputs
the MONI bus signal after the MONI MASTER
control, and can be connected to the input of a
powered monitor speaker.
EMX620—Owner’s Manual
Rear Panel
11
Rear Panel
POWERED MIXER
MODEL EMX620
POWER
ON
OFF
B—SPEAKERS—A
1
2
1 POWER switch
B SPEAKERS A & B jacks
The POWER switch is used to turn on and off the
power to the EMX620.
Note: Before turning on or off the EMX620, it’s
a good idea to turn down the MAIN MASTER
and MONI MASTER controls.
The SPEAKER A & B phone jacks output the
main signal from the internal power amplifier
and are used to connect speakers. They are internally connected in parallel and output the same
signal. The total impedance of the connected
speaker system must be between 4 and 8 ohms.
This means that you can connect one speaker system with an impedance of between 4 and 8 ohms
to one SPEAKER jack, or two speaker systems
each with an impedance of between 8 and 16
ohms to each SPEAKER jack, as shown below.
Connecting one speaker
B—SPEAKERS—A
4Ω–8Ω
Connecting two speakers
B—SPEAKERS—A
8Ω–16Ω 8Ω–16Ω
Note: Do not connect anything other than
speakers to these jacks.
EMX620—Owner’s Manual
12
Front & Rear Panels
Hookup Example
Recorder (Cassette, DAT, MD)
CD player
Effects processor
88
Synthesizer,
Drum machine,
Guitar processor
Hi-Z
Hi-Z
Hi-Z
Powered monitor
Hi-Z
LINE
1
Lo-Z
Lo-Z
Lo-Z
INST
MONITOR
EFFECT OUT
1
TAPE
IN
REC
OUT
1
1
2
2
Lo-Z
LINE
2
INST
FOOT SW
MAIN PHONES
AUX IN
2
INPUT
TO MAIN
*1
Footswitch
(YAMAHA FC5)
OUTPUT
*2
Headphones
Larger mixer
or
Amplifier
Microphone
B—SPEAKERS—A
Electric-acoustic
guitar
Electric bass
* The Lo-Z and Hi-Z input of each channel cannot
be used simultaneously.
*1. Although this example shows an external effects
processor and footswitch, which is used to turn
on and off the built-in digital effects processor,
connected to the EMX620, in practice, only one
effects processor, internal or external, will be
used at a time, so the footswitch is not required
when using external effects.
*2. This example shows both headphones and a
powered monitor being used for monitoring.
In practice, however only one method is
required.
EMX620—Owner’s Manual
Basic Operation
13
Basic Operation
Connecting Sources
Before connecting any microphones or instruments, make sure that the EMX620 and any other
applicable equipment is turned off. Also make
sure that the LEVEL control on each EMX620
input channel, and the MAIN MASTER and
MONI MASTER controls are turned down.
1 Connect cables to your mics and instruments, and insert the other end of the
cables firmly into the appropriate Lo-Z or
Hi-Z jack (channels 1–4), LINE jack (channel 5), or INST jack (channel 6).
Note: When connecting line-level sources to
input channels 1 through 4, turn on the corresponding PAD switch.
Note: The Lo-Z and Hi-Z jacks on input channels 1 through 4 cannot be used simultaneously.
B Turn on the power, starting with the
sound sources and finishing with the
EMX620.
Reverse this order when turning off the power.
C Set the MAIN MASTER control to the √
position.
D While speaking into a connected mic, or
playing a connected instrument, adjust
the input channel LEVEL control so that
the 0 LED of the MAIN section level meter
lights occasionally.
Repeat this procedure for each channel.
E Use the EQ controls on each input channel to adjust the tonal characteristics of
each source.
F Use the 7-band graphic equalizer to
adjust the tonal characteristics of the
main output.
G Use the MAIN MASTER control to set the
overall volume level of the main mix.
Monitoring
By connecting a powered monitor speaker to the
MONITOR OUTPUT, you can create a monitor
mix independent of the MAIN mix, since the
input channel MONI controls are not affected by
the LEVEL controls.
1 Set the MONI MASTER control to the √
position.
B While speaking into a connected mic, or
playing a connected instrument, adjust
the MONI control of the input channel
that you want to monitor.
Repeat this procedure for each channel.
C Use the MONI MASTER control to set the
overall level of the monitor mix.
Using the Built-in Effects
The EMX620 features a built-in digital effects
processor, allowing reverberation or ambiance to
be added to vocals or instrument sounds.
1 Turn on the digital effects processor by
pressing the DIGITAL EFFECT ON switch.
The DIGITAL EFFECT indicator lights up.
B Use the DIGITAL EFFECT switches to select
an effects program.
VOCAL ...... Reverb suitable for vocals.
L. HALL...... Reverb typical of a large hall.
S. HALL...... Reverb typical of a small hall.
C Set the MAIN EFFECT RTN control to the
√ position.
D While speaking into a connected mic, or
playing a connected instrument, adjust
the EFFECT control of the input channel
that you want to process.
E Use the MAIN EFFECT RTN control to
adjust the overall level of the processed
sound.
F Use the MONI EFFECT RTN control to feed
the processed signal to the MONI bus and
subsequently MONITOR OUTPUT.
Note: If the processed sound is distorted even
with an EFFECT RTN control turned down,
turn down the EFFECT control on each channel.
EMX620—Owner’s Manual
14
Troubleshooting
Troubleshooting
The following table describes the possible malfunctions of this demvice, and the appropriate actions to be
taken in each case.
Problem
The POWER
indicator is lit.
Cause
Action
The load on the amplifier of this device
was too great, and the protection circuit
for the amplifier has operated. Possible
reasons for the excessive load are an
excessive level setting in the channel
control section or main section, insufficient ventilation, or insufficient load
impedance of the connected speakers.
Please wait. When the device cools off, normal
operation will resume automatically. However,
please check the following three points to prevent
the problem from recurring.
If the level setting is excessive, lower it to the nominal level. You can refer to the peak level indicators
of the main section when doing so.
If the device is not ventilated sufficiently, refer to
the cautions given at the beginning of this manual
and take appropriate measures to insure adequate
ventilation.
If the load impedance (including a short) is too
low, refer to the chapter on rear panel (page 11)
and change the connections so that the impedance
is correct.
Sound is no
longer output from the
speakers.
Connections between devices have come Inspect the connections, and correct any faulty
loose.
connections.
Other
Other
EMX620—Owner’s Manual
The device may have malfunctioned. Please contact
your dealer.
Specifications
15
Specifications
■ General Specifications
Maximum output power
135 W/8Ω @0.5% THD at 1 kHz (SPEAKERS OUT)
200 W/4Ω @0.5% THD at 1 kHz (SPEAKERS OUT)
175 mW/40Ω @0.5% THD at 1 kHz (PHONES OUT)
Frequency response
20 Hz–20 kHz +1 dB, –3 dB @1 W output into 8Ω (SPEAKERS OUT)
20 Hz–20 kHz +1 dB, –3 dB @+4 dB output into 10 kΩ (MAIN OUT, MONITOR OUT, EFFECT OUT)
Total harmonic distortion
Less than 0.5% @20 Hz–20 kHz, 100 W output into 4Ω (SPEAKERS OUT)
Less than 0.3% @20 Hz–20 kHz, +14 dB output into 10 kΩ (MAIN OUT, MONITOR OUT, EFFECT OUT)
–124 dB equivalent input noise, –68 dB residual output noise (SPEAKERS OUT)
–88 dB residual output noise (MAIN OUT, MONITOR OUT)
Hum & noise
(Average, Rs=150Ω)
(with 20 Hz–20 kHz BPF)
–79dB (83 dB S/N)
(MAIN OUT, MONITOR OUT)
Master level control: nominal level
Channel level controls: minimum
–69 dB (73 dB S/N)
(MAIN OUT, MONITOR OUT)
Master level control: nominal level
1 channel level control: nominal level
–75 dB (79 dB S/N)
(EFFECT OUT)
All channel level controls: minimum
–69 dB (73 dB S/N)
(EFFECT OUT)
1 channel level control: nominal level
Maximum voltage gain
(PAD: OFF)
86 dB CH IN (Lo-Z) to SPEAKERS OUT (CH1–4)
66 dB CH IN (Lo-Z) to MAIN OUT, MONITOR OUT (CH1–4)
66 dB CH IN (Lo-Z) to EFFECT OUT (CH1–4)
48 dB CH IN (Lo-Z) to REC OUT (CH1–4)
56 dB CH IN (Hi-Z) to MAIN OUT, MONITOR OUT (CH1–4)
26 dB LINE IN to MAIN OUT
26 dB AUX IN to MAIN OUT
22 dB TAPE IN to MAIN OUT
46 dB INST IN to MAIN OUT
Crosstalk at 1 kHz
–65 dB adjacent input, –65 dB input to output
Input channel equalization
±15 dB Maximum
HIGH
10 kHz shelving *
LOW
100 Hz shelving *
* Turn over/roll-off frequency of shelving: 3 dB below maximum variable level.
Meters
5 points LED Meter (–10, –5, 0, +3, +6 dB) MAIN OUT
Graphic equalizer
7 bands (125, 250, 500, 1k, 2k, 4k, 8k Hz) MAIN OUT
±12 dB Maximum
Internal digital effect
3 types (Vocal, L Hall, S Hall)
Phantom power
+15 V is supplied to electrically balanced inputs for powering condenser microphones via 2.4 kΩ current
limiting/isolation resisters.
Limiter
Comp. : THD≥0.5% (SPEAKERS)
LIMIT indicator
Turn on. : THD≥0.5% (SPEAKERS)
Protection circuit
(Power amp)
POWER switch on/off mute
DC detection
Temp (Heatsink Temp≥90°C)
Foot switch
DIGITAL EFFECT MUTE : on/off
Power requirement
USA and Canada: 120 V AC 60 Hz
Europe:
230 V AC 50 Hz
Other:
240 V AC 50 Hz
Power consumption
110 W
Dimensions (WxHxD)
497×275×275 mm
Weight
13 kg
For European Model
Purchaser/User Information specified in EN55103-1 and EN55103-2.
Inrush Current: 23A
Conformed Environment: E1, E2, E3 and E4
EMX620—Owner’s Manual
16
Specifications
■ Input Specifications
Input connectors PAD
CH INPUT (Lo-Z)
(CH1–4)
OFF
CH INPUT (Hi-Z)
(CH1–4)
OFF
ON
ON
Actual load
impedance
3 kΩ
10 kΩ
Input level
Nominal
impedance
Sensitivity*1
Nominal level
Max. before cliping
Connector
type
50–600Ω Mics
–62 dB (0.616 mV)
–50 dB (2.45 mV)
–20 dB (77.5 mV)
600Ω Lines
–32 dB (19.5 mV)
–20 dB (77.5 mV)
+10 dB (2.45 V)
50–600Ω Mics
–52 dB (1.95 mV)
–40 dB (7.75 mV)
–10 dB (245 mV)
600Ω Lines
–22 dB (61.6 mV)
–10 dB (245 mV)
+20 dB (7.75 V)
Phone jack
(TRS)*2
XLR-3-31
type*2
LINE IN (CH5) (1–2)
10 kΩ
600Ω Line
–22 dB (61.6 mV)
–10 dB (245 mV)
+20 dB (7.75 V)
Phone jack *3
INST IN (CH6) (1–2)
470 kΩ
1kΩ
–42 dB (6.16 mV)
–30 dB (24.5 mV)
0 dB (0.775 V)
Phone jack *3
AUX IN
10 kΩ
600Ω Line
–22 dB (61.6 mV)
–10 dB (245 mV)
+20 dB (7.75 V)
Phone jack *3
TAPE IN (1–2)
10 kΩ
600Ω Line
–22 dBV (79.4 mV)
–10 dBV (316 mV)
+17.8 dBV (7.76 V) Phono jack
*1. Sensitivity is the lowest level that can produce an output of +4 dB (1.23 V) or the nominal output level when the unit is set at maximum gain.
(All level controls are at maximum position.)
*2. Balanced. (T= HOT, R= COLD, S= GND)
*3. Unbalanced.
• 0 dB= 0.775 Vrms, 0 dBV= 1 Vrms.
■ Output Specifications
Output level
Actual source
impedance
Nominal
impedance
Nominal
Max. before cliping
0.1Ω
4/8Ω Speaker
37.7 W/4Ω
200 W/4Ω
Phone jack
MAIN OUT
600Ω
10 kΩ Lines
+4 dB (1.23 V)
+20 dB (7.75 V)
Phone jack
MONITOR OUT
600Ω
10 kΩ Lines
+4 dB (1.23 V)
+20 dB (7.75 V)
Phone jack
EFFECT OUT
600Ω
10 kΩ Lines
+4 dB (1.23 V)
+20 dB (7.75 V)
Phone jack
PHONES OUT
35Ω
40 Ω Phones
33 mW
175 mW
Phone jack
REC OUT (1, 2)
600Ω
10 kΩ Lines
–10 dBV (316 mV)
+10 dBV (3.16 V)
Phono jack
Output connectors
SPEAKERS OUT (A, B)
Connector type
• PHONE JACKS are unbalanced.
• 0 dB= 0.775 Vrms, 0 dBV= 1 Vrms.
■ Dimensions
168
(45.5)
H:275
259
(45.5)
W:497
45.5
380
45.5
487
16
57.5
150
(67.5)
D:275
Unit: mm
Specifications are subject to change without prior notice.
EMX620—Owner’s Manual
CH6 IN
CH5 IN
CH IN
1-4
–50dB
–40dB
–30dB
–20dB
–10dB
0dB
+10dB
+20dB
+30dB
INST
[–30dB]
LINE
[–10dB]
2
1
2
1
Hi-Z
[–40/–10]
Lo-Z
[–50/–20]
Lo-Z, MIC [–50dB]
INST IN
[–30dB]
Hi-Z [–40dB]
Lo-Z [–20dB]
Hi-Z [–10dB]
HA
HA
FOOT SW
(MITE)
TAPE IN
[–10dBV]
[–7.8dB]
[–10dB]
ON
OFF
[–10dB]
2
1
[–10dB]
BA
BA
2-Stage EQ
2-Stage EQ
2-Stage EQ
AUX IN [–10dB]
TAPE IN [–10dBV]
Clip Level [+20dB]
S HALL
L HALL
VOCAL
AUX IN
[–10dB]
PAD
[–10dB]
LINE IN
[–10dB]
[–10dB]
PAD
HA
Lo
Lo
Lo
+15V
Hi
Hi
Hi
DIGITAL
EFFECT
ON
[0dB]
ON
ON
ON
[–16dB]
TAPE IN
[–16dB]
AUX IN
LEVEL
[–10dB]
LEVEL
[–10dB]
LEVEL
[–10dB]
MAIN
[0dB]
[–16dB]
ON
EFFECT
MONI
SUM
SUM
SUM
MAIN,MONI [–16dB]
EFFECT [–22dB]
TAPE,AUX
[–6dB]
EFFECT RTN
[–6dB]
EFFECT RTN
SUM
MONI
[–22dB]
EFFECT
[–16dB]
[–16dB]
MONI
[–22dB]
EFFECT
[–16dB]
[–16dB]
[–22dB]
MONI
EFFECT
[–16dB]
[0dB]
[0dB]
[0dB]
REC OUT
[–10dBV]
[–7.8dB]
7-Stage GEQ
2
1
[–6dB]
BA
BA
[–6dB]
MASTER
MASTER
REC OUT [–10dBV]
125Hz
250Hz
500Hz
1kHz
2kHz
4kHz
8kHz
PHANTOM
OFF
EFFECT OUT
[+4dB]
MONITOR OUT
[+4dB]
MAIN OUT
[+4dB]
MAIN OUT, MONITOR OUT, EFFECT OUT [+4dB]
BA
LED METER
1
2
JK2
JK1
PHONE
B
A
PHONE (33mW 40Ω)
PHONE max
(175mW 40Ω)
37.7W/4Ω
–50dB
–40dB
–30dB
–20dB
–10dB
0dB
+10dB
+20dB
+30dB
SPEAKERS
[200W/4Ω]
SPEAKERS
MAXIMUM OUTPUT POWER [200W/4Ω]
LIMIT
PA
1
2
Block & Level Diagrams
17
■ Block & Level Diagrams
EMX620—Owner’s Manual
YAMAHA CORPORATION
V474530 R1 1 IP 20
Printed in Taiwan
Pro Audio Division, #18/3
P.O. Box 3, Hamamatsu, 430-8651, Japan