- Home
- Domestic appliances
- Small kitchen appliances
- Barbecues & grills
- Centro
- 85-3015-6, 4900IR NG
- User manual
Centro 85-3014-8,4900IR LP Bbq And Gas Grill 2009 Assembly Manual
Add to my manualsadvertisement
CENTRO 4900IR
Assembly Manual
85-3014-8 (G51208) Propane
85-3015-6 (G51211) Natural Gas
LIMITED 5-YEAR WARRANTY
Read and save manual for future reference.
Assemble your grill immediately.
Missing or damaged parts should be claimed within 30 days of purchase.
For product inquiries, parts, warranty and troubleshooting support, please call 1-877-707-5463.
Manual Revision #: 07012009 SA
H E A V Y A R T I C L E N E E D S 2 T O L I F T
THIS MANUAL MUST REMAIN WITH THE PRODUCT AT ALL TIMES
To ORDER non-warranty replacement parts or accessories, or to register your warranty, please visit us on the web at
www.centrobbqs.com.
CAUTION
Sharp edges. Wear gloves when assembling your grill.
CAUTION
Read and follow all safety statements, assembly instructions, and use and care directions before attempting to assemble and cook.
INSTALLER OR ASSEMBLER/CONSUMER
This manual should be kept with the BBQ at all times.
WARNING
Failure to follow all of the Manufacturer’s instructions could result in hazardous fi res, explosions, property damage, or serious personal injury or even death.
Follow all leak check procedures carefully prior to operation of barbecue, even if grill was dealer assembled. Do not try to light this barbecue without reading the Lighting
Instructions section of this manual.
DANGER
1. If you smell Gas: a. Shut off gas to the appliance b. Extinguish any open fl ame c. Open lid d. If odor continues, keep away from
the appliance and immediately
call your gas supplier or your
fi re department
2. Do not store or use gasoline or other fl ammable vapours and liquids in the vicinity of this or any other appliance.
3. An LP cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.
4. Requires two people to complete the assembly process.
5. Beware of sharp edges.
T H I S B A R B E C U E I S F O R O U T D O O R U S E O N L Y
CO N TAC T C A L L C E N T R E I F A NY PA R T S A R E M I S S I N G
1 - 8 7 7 - 7 0 7 - 5 4 6 3
HARDWARE PACK
TOOLS NEEDED FOR ASSEMBLY
• #2 Phillips screwdriver (Long and short)
• ¼” Slotted screwdriver (Long and short)
• Adjustable wrench
• Pliers
• Rubber Mallot
Before assembling the barbecue, read these instructions carefully.
Assemble the barbecue on a fl at, clean surface.
Grill is heavy.
Notes: Do not fully tighten all the nuts during this initial stage.
No.
Description
1 ¼"-20UNCX13 Screw
8
9
6
7
4
5
2
3
¼"-20UNCX38 Screw
¼"-20UNCX16 Screw
ø7 Lock Washer
ø7 Washer
NO.10-24UNCx10 Screw
ø 5 Lock Washer
ø 5 Washer
ST4.2x10 Tapping Screw
10 Wrench
11 NO.8-32UNCx10 Screw
12 Control Knob
13 NO. 10 Nut
14 ST4.2x20 Tapping Screw
Caution:
Sheet metal can cause injury. Wear gloves when installing the grill.
Part Number
20120-13013-250
20120-13038-250
20120-13016-250
41400-07000-250
40300-07000-250
20124-10010-250
41400-05000-250
40300-05000-250
22500-42010-137
G413-0032-9082
20332-08010-250
G412-4500-9000
30244-10000-250
22500-42018-250
Quantity
8
28
28
28
9
20
20
4
8
1
4
1
4
1
1
4
¼” - 20UNCX13 Screw
X 8
ø7 Lock Washer
X 20
7
ø5 Lock Washer
X 28
10
Wrench
X 1
13
NO. 10 Nut
X 4
2
5
¼” - 20UNCX38 Screw
X 4
ø7 Washer
X 20
8
ø5 Washer
X 28
11
NO. 8-32UNCx10 Screw
X 4
14
ST4.2x20 Tapping Screw
X 1
3
¼” - 20UNCX16 Screw
X 8
6
9
ST4.2x10 Tapping Screw
X 9
12
NO. 10-24UNC10 Screw
X 28
Knob
X 1
1
PARTS LIST (PROPANE) FOR 85-3014-8 (G51208)
Item Qty. Description
AE
AF
AG
AH
AA
AB
AC
AD
2
2
1
1
1
1
1
1
Top Lid
Lid Handle
Lid Handle End Cap-Left
Lid Handle End Cap-Right
Logo Plate
Thermometer
Screw for Top Lid
Lid Bumper
BK1
BK2
BK3
BL
BF
BG
BH
BI
BJ
BA
BA1
BB
BC
BD
BE
1
1
1
1
3
1
1
3
1
2
1
1
1
1
1
Burner Box Assembly
Rotisserie Burner Brace
Upper Side Panel- Left
Upper Side Panel- Right
Main Burner-A
Main Burner-B
Carryover Assembly
Flame Tamer
Cooking Grate, Burner Box
Warming Rack
Rotisserie Burner
Electrode Set, Rotisserie Burner
Ground Wire, Rotisserie Burner
Wind Shield, Rotisserie
Match Holder
CF2
CG1
CG2
CH
CI
CJ
CK
CL
CM
CN
CA
CB
CC
CD
CE1
CE2
CF1
1
1
1
1
1
1
1
1
1
1
1
3
1
1
1
1
1
Manifold Assembly with Coupling
Regulator
Valve, Sideburner
Metal Hose, Sideburner
Rotisseries Flexible Hose
Rotisseries LP Orifi ce
Electronic Igniter Assembly
Electronic Ignition Button
Electrode Set, Main Burner
Ground Wire, Main Burners
Control Knob Assy
Rotisserie Knob Assy
Series Logo
Control Panel
Front Brace
Grease Tray
Grease Cup
G512-5400-01
G433-0034-01
G512-0040-01
G608-0039-01
G411-0013-01
G411-0013-02
G508-0075-01
G501-0072-01
G617-0017-01
G411-0004-01
G412-4500-01
G617-4200-01
G512-0033-01
G512-0017-03
G512-0044-01
G512-1000-01
G416-0015-01
G512-0200-01
G512-0015-01
G617-0500-01
G617-0600-01
G607-0700-A1
G502-1800-A1
G502-0012-01
G617-0019-01
G512-0028-02
G512-0004-01
G617-2900-01
G411-0002-01
G411-0004-01
G617-0036-01
G608-0019-01
Part No.
G512-2900-01
G512-0001-01
G617-0004-01
G617-0005-01
G412-0001-01
G412-0003-01
G501-0005-01
G508-0063-01
Item Qty. Description
CO
CP
1
1
Upper Back Panel
Heat Shield
1
1
1
1
1
1
1
1
1
1
1
1
1
DA
DB
DC1
DC2
DD
DE
DF1
DF2
DG
DH
DI
DJ
DK
Side Shelf Table- Left
Side Shelf Fascia- Left
Sear Zone Wind Shield
Sear Zone Support Frame
Side Zone Burner
Electrode Set, Sear Zone
Lid Sear Zone
Lid Handle Sear Zone
Side Shelf Wind Shield
Cooking Grate Sear Zone
Cooking Griddle Sear Zone
Side Shelf Table-Right
Side Shelf Fascia-Right
1
1
1
2
1
1
1
2
2
1
ED
EE
EF
EG
EA
EB
EC
EH
EI
EJ
Cart side panel-Left
Cart Side Panel, Right
Pillar, Left
Pillar, Right
Magnet Assembly
Door Assembly
Bottom Shelf
Wheel withLock
Wheel
Towel Bar
F1
F2
F3
1
1
1
Hardware Pack
Instruction Manual
Safety & Care Manual
Part No.
G512-0045-01
G512-0026-01
G512-3900-01
G617-0034-01
G617-0066-01
G617-0058-01
G617-5200-01
G610-0009-01
G512-0030-01
G607-0040-01
G512-0046-01
G617-0060-01
G617-0061-01
G512-3800-01
G617-0026-01
G617-0700-01
G617-0800-01
G512-1600-01
G512-1700-01
G501-0016-01
G512-5300-01
G512-0900-01
G401-0061-01
G606-0027-01
G511-0050-02
G512-B008-01
G512-M008-01
G412-M004-02
EXPLODED DIAGRAM (PROPANE) FOR 85-3014-8 (G51208)
DC2
DC1
BL
2 3
PARTS LIST (NATURAL GAS) FOR 85-3015-6 (G51211)
Item Qty. Description
AE
AF
AG
AH
AA
AB
AC
AD
2
2
1
1
1
1
1
1
Top Lid
Lid Handle
Lid Handle End Cap-Left
Lid Handle End Cap-Right
Logo Plate
Thermometer
Screw for Top Lid
Lid Bumper
BH
BI
BJ
BK1
BK2
BK3
BL
BD
BE
BF
BG
BA
BA1
BB
BC
1
1
1
1
1
3
1
1
3
2
1
1
1
1
1
Burner Box Assembly
Rotisserie Burner Brace
Upper Side Panel- Left
Upper Side Panel- Right
Main Burner-A
Main Burner-B
Carryover assembly
Flame Tamer
Cooking Grates
Warming Rack
Rotisserie Burner
Electrode Set, Rotisserie Burner
Ground Wire, Rotisserie Burner
Wind Shield, Rotisserie
Match Holder
CA
CB
CC
CD
CE1
CE2
CF1
CF2
CG1
CG2
CH
CI
CJ 1
CK 1
CL
CM
CN 1
1
1
3
1
1
1
1
1
1
1
1
1
1
1
Manifold Assembly with Coupling
Natural Gas Hose
Valve, Sideburner
Metal Hose, Sideburner
Rotisserie Flexible Hose
Rotisserie LP Orifi ce
Electronic Igniter Assembly
Electronic Ignition Button
Electrode Set, Main Burner
Ground Wire, Main Burners
Control Knob Assy
Rotisserie Knob Assy
Series Logo
Front Brace
Grease Tray
Grease Cup
Part No.
G512-2900-01
G512-0001-01
G617-0004-01
G617-0005-01
G412-0001-01
G412-0003-01
G501-0005-01
G508-0063-01
G512-5700-01
G501-0099-01
G512-0041-01
G608-0039-01
G601-0072-01
G601-0072-02
G508-0075-01
G501-0072-01
G617-0017-01
G411-0004-01
G412-4500-01
G617-4200-01
G512-0033-01
G512-0017-03
G512-0044-01
G512-1000-01
G416-0015-01
G512-0200-01
G512-0015-01
G617-0500-01
G617-0600-01
G607-0700-A1
G502-1800-A1
G502-0012-01
G617-0019-01
G512-0028-02
G512-0004-01
G617-2900-01
G411-0002-01
G411-0004-01
G617-0036-01
G608-0019-01
Item Qty. Description
CO
CO
1
1
Upper Back Panel
Heat Shield
F1
F2
F3
EE
EF
EG
EH
EA
EB
EC
ED
EI
EJ
DE
DF1
DF2
DG
DH
DI
DJ
DA
DB
DC1
DC2
DD
DK
1
1
1
1
2
2
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Side Shelf Table- Left
Side Shelf Fascia- Left
Sear Zone Wind Shield
Sear Zone Support Frame
Sear Zone Burner
Electrode Set, Sear Zone
Lid Sear Zone
Lid Handle Sear Zone
Side Shelf Wind Shield
Cooking Grate Sear Zone
Cooking Griddle Sear Zone
Side Shelf Table-Right
Side Shelf Fascia-Right
Cart Side Panel-Left
Cart Side Panel, Right
Pillar, Left
Pillar, Right
Magnet Assembly
Door Assembly
Bottom Shelf
Wheel with Lock
Wheel
Towel Bar
Hardware Pack
Instruction Manual
Safe & Care Manual
Part No.
G512-0045-01
G512-0026-01
G512-3900-01
G617-0034-01
G617-0066-01
G617-0058-01
G617-5200-01
G610-0009-01
G512-0030-01
G607-0040-01
G512-0046-01
G617-0060-01
G617-0061-01
G512-3800-01
G617-0026-01
G617-0700-01
G617-0800-01
G512-1600-01
G512-1700-01
G501-0016-01
G512-5300-01
G512-2500-01
G401-0061-01
G606-0027-01
G511-0050-02
G512-B008-01
G512-M008-01
G412-M004-02
EXPLODED DIAGRAM (NATURAL GAS) FOR 85-3015-6 (G51211)
DC2
DC1
4 5
ASSEMBLY INSTRUCTIONS
1
EH
EI
Seperate the 2 diff erent types of wheels, 2 locking wheels (EH) and 2 regular wheels (EI).
Attach the locking wheels (EH) to the back of the bottom shelf (EG) and the regular wheels (EI) to the front of the bottom shelf (EG).
To secure the 4 wheels, hand tighten fi rst. Then, tighten further using the wrench provided in the hardware pack.
EG
Back view
X 1
ASSEMBLY INSTRUCTIONS
3
CL
EB
Attach the front brace (CL) to the Left and right cart side panels (EA and EB)
TIP: One person should align the left side, while the second person assembles the right side.
EA
YOU WILL NEED:
X 4 X 4 X 4
Back view
2
Close up
EA
EB
Ensure that the wheels are fi rmly locked in the
“ON” position before continuing.
Assemble the left side panel (EA) and the right side panel (EB) to the bottom shelf (EG).
Front view
EG
YOU WILL NEED:
8 5
X 6 X 6 X 6
4
A
EC
C
CL
B
EG
D
CJ
Assemble the left and right pillars (EC and ED), to the cart side panels, as shown in fi gure A and B.
Next, assemble the left and right pillars to the front brace (CL) and the bottom shelf (EG), as shown in fi gure C and D.
TIP: One person should align the left side, while the second person assembles the right side.
YOU WILL NEED:
X 8 X 8 X 8
Close up
6 7
ASSEMBLY INSTRUCTIONS
5
A + B
THIS STEP REQUIRES 3 OR MORE PEOPLE.
DO NOT ATTEMPT ALONE. EXTREMELY
HEAVY.
a. Position the top lid and burner box assembly
(A and B) onto cart assembly (C) as shown.
b. Use the hardware to connect both parts, on the left and right sides, at the three points indicated in fi gure B and C.
C
A
YOU WILL NEED:
B C
X 6 X 6 X 6
6
Back view
EB
B
EA
CO
Attach the upper back panel (CO) to both the left and right side panels (EA and EB).
Only install hardware in the bottom portion of the back panel (CO), as shown in fi gure B.
YOU WILL NEED:
2 4 5
X 2 X 2 X 2
ASSEMBLY INSTRUCTIONS
7
8
DK
DJ
Attach the right side shelf fascia (DK) to the right side shelf table (DJ), as shown.
YOU WILL NEED:
X 3 X 3 X 3
B B
B
B
BC
DJ
TIP: To position the right side shelf, insert the two hooks on the side shelf assembly into the two openings located on the right upper side panel
(BC).
Assemble the right side shelf assembly to the cart assembly, as shown in fi gure B.
DK
B
* A
YOU WILL NEED:
2
A
X 1
3
B
X 4
4
X 1
4
X 4
5
X 1
5
X 4
8 9
ASSEMBLY INSTRUCTIONS
9
Front a. Attach the left shelf fascia (DB) to the left side shelf table (DA).
YOU WILL NEED:
DC1
X 3 X 3 X 3
DB
DA
10
A
DG
B
A *
B
DG
B
DA
DB
C DA
DF1
BB
DB
B
B
B
DG b. Assemble the Side shelf wind shield (DG) to the left side shelf table (DA), and the left side shelf fascia (DB), as shown in Figure B and C.
YOU WILL NEED:
9
X 5
TIP: To position the left side shelf assembly, insert the two hooks on the side shelf assembly into the two openings located on the upper left side panel (BB).
Assemble the left side shelf assembly to the cart assembly, as shown in fi gure B.
YOU WILL NEED:
2
A
X 1
3
B
X 4
4
X 1
4
5
X 1
5
X 4 X 4
10
ASSEMBLY INSTRUCTIONS
11
CC
A
B
DA
DB
CC
12
11
Remove the hardware that is pre-assembled to the side burner valve bracket(CC), as shown in fi gure
A. Insert the side burner valve stem through the rear of the left side shelf fascia(DB). Assemble the side burner valve (cc) to the side shelf fascia (DB), using the hardware removed.
Assemble the side burner control knob (#12) to the side burner valve (CC).
Hardware may be included with the hardware pack.
YOU WILL NEED:
12
X 1
ASSEMBLY INSTRUCTIONS
12 a. Position the Sear Zone burner (DD) through the opening in the left side shelf (DA).
ASSEMBLY INSTRUCTIONS
12 e. Attach the end of the side burner electrode wire (DE) to the underside of the side burner electrode, as shown in fi gure E.
Ensure that the wire is pushed in fi rmly.
A
DA
DD
CC
DD b. Make sure that the Sear Zone burner (DD) engages the Sear Zone burner valve (CC), gas jet, as shown in fi gure B.
B
C
DC
D
DC1 DD
DE
12 c. Assemble the Sear Zone burner (DD) to the
Sear Zone support frame (DC1), at the 4 points indicated in fi gure C.
YOU WILL NEED:
13
X 4 X 4 X 4 X 4 d. Feed the Sear Zone electrode wire (DE) from underneath the Sear Zone burner (DD), through the small opening on the right side of the Sear
Zone support frame (DC1). Align and assemble the electrode using the self tapping screw provided, as shown in fi gure D.
YOU WILL NEED:
X 1
13
E
F DI
DE
G
DH
A
B
CP
CP
13 f. Position either the Sear Zone cooking griddle
(DI) or the cooking grate (DH) in position on the Sear Zone side burner side shelf. Store the extra accessory within the BBQ chart.
Place the heat shield (CP) into the groove which is located at the back side of the front brace (CL) as shown in fi gure A. Next, attach the heat shield (CP) to the upper back panel
(CO) by using the self tapping screws (X 4), as shown in fi gure B.
YOU WILL NEED:
9
X 4
ASSEMBLY INSTRUCTIONS
14 TIP: Before attempting to assemble the door (EF) to the right pillar (ED), locate the two clasps on the door hinge. Next, locate the two small openings on the right side pillar (ED).
EF
ED a. Hold the door (EF) perpendicular to the BBQ
Cart. Align the two clasps on the door hinge
(EF), with the two holes on the right side pillar
(ED). Once aligned, push the two clasps into the openings, and immediately push down to lock clasps in place.
EF b. Assemble the door (EF) to the right pillar (ED), as shown in fi gure B, using the screws provided.
YOU WILL NEED:
11
X 4
EJ b. Assemble the towel bar (EJ) onto door (EF).
YOU WILL NEED:
8 5
X 2 X 2 X 2
ASSEMBLY INSTRUCTIONS
15
BG
16
Model may not be exactly as shown.
A
BH
Place the fl ame tamers (BG) into the burner box. a. Place the cooking grates (BH) into the burner box, as shown in fi gure A.
b. Insert the three small positioning rods of the warming rack (BI) into the rotisserie burner brace (BA1).
B
BI
BA1
14 15
ASSEMBLY INSTRUCTIONS
17
CM
CO
CN
18 a. Insert the grease tray (CM) into the opening in the upper back panel (CO), making sure to engage tracks located under burner box.
b. Place the grease cup (CN) onto the tracks, located on the underside of the grease tray (CM).
ASSEMBLY INSTRUCTIONS
19
FOR PROPANE MODEL ONLY.
For natural gas model, follow step 20.
a. Position the 20 lb propane tank onto the bottom shelf (EG), and secure using the bolt
(already attached) located on the underside of the bottom shelf, as shown in fi gure B.
A
CF2
Unscrew the electronic ignitor button (CF2) and insert one AA battery into the electronic igniter battery compartment, with the positive end facing outward.
* Battery not included.
20
B
EG b. Attach the regulator coupling nut to the LP cylinder valve.
ATTENTION: For your families safety, do not attempt to light this BBQ until you have reviewed pages 4-7 of the CENTRO Safety & Care Manual.
All Safety and Leak test MUST BE PERFORMED BY
THE END USER, prior to lighting this BBQ.
WARNING
Do not store extra propane tanks within BBQ cart.
CC
CB
FOR NATURAL GAS MODEL ONLY.
Attach the natural gas hose (CB) to the side burner valve (CC) as shown.
ATTENTION: In order to complete installation of your Natural Gas BBQ a 1/2” or 3/8” adapter may be required to connect your
BBQ’s Natural Gas hose to your home gas supply. Contact your Natural Gas supplier to purchase the necessary part.
16 17
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project