Version 1.1 | 02/22/2013
User Manual
Cloud Camera 2350
DCS-2332L
Preface
D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization
of such revisions or changes. Information in this document may become obsolete as our services and websites develop and change. Please refer
to http://www.mydlink.com for the most current information.
Manual Revisions
Revision
Date
Description
1.0
November 1, 2012
DCS-2332L Revision A1 with firmware version 1.00
1.1
February 22, 2013
Updated Technical Specs
Trademarks
D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United States or other
countries. All other company or product names mentioned herein are trademarks or registered trademarks of their respective companies.
Copyright © 2013 D-Link Corporation.
All rights reserved. This publication may not be reproduced, in whole or in part, without prior expressed written permission from D-Link Corporation.
D-Link DCS-2332L User Manual
2
Table of Contents
Product Overview............................................................... 5
Package Contents.......................................................................... 5
System Requirements.................................................................. 5
Introduction.................................................................................... 6
Features............................................................................................. 7
Hardware Overview...................................................................... 8
Front........................................................................................... 8
Rear: External.......................................................................... 9
Rear: Internal.........................................................................10
Removing the Top Panel...........................................................11
Removing the Power Cable..............................................12
Replacing the Ethernet Cable.........................................13
Reattaching the Top Panel................................................14
Removing the Bottom Panel...................................................15
Using the Reset Button..............................................................15
Installing a microSD Memory Card...............................16
Reattaching the Bottom Panel........................................16
Installation........................................................................18
Zero Configuration Setup.........................................................18
Camera Setup Wizard.................................................................21
Windows Users.............................................................................21
Mac Users.......................................................................................29
Manual Hardware Installation.................................................30
mydlink..............................................................................31
Camera Status...............................................................................32
Live Video.......................................................................................33
D-Link DCS-2332L User Manual
Playback..........................................................................................34
Settings...........................................................................................35
Recording Settings..............................................................36
Advanced Settings..............................................................38
Events.......................................................................................39
Configuration....................................................................40
Using the Configuration Interface.........................................40
Live Video.......................................................................................41
Setup................................................................................................43
Setup Wizard.........................................................................43
Internet Connection Setup Wizard............................44
Motion Detection Setup Wizard.................................47
Network Setup......................................................................49
Wireless Setup.......................................................................52
Dynamic DNS........................................................................53
Image Setup..........................................................................54
Audio and Video...................................................................56
Preset.......................................................................................58
Motion Detection................................................................60
Time and Date.......................................................................61
Event Setup............................................................................62
Add Server..............................................................................64
Add Media..........................................................................65
Add Event...........................................................................67
Add Recording..................................................................69
microSD Card........................................................................71
3
Advanced.......................................................................................72
ICR and IR................................................................................72
HTTPS.......................................................................................73
Access List..............................................................................74
System.....................................................................................75
Maintenance.................................................................................76
Device Management..........................................................76
Firmware Upgrade...............................................................77
Status...............................................................................................78
Device Info.....................................................................................78
Logs..........................................................................................79
Help..........................................................................................80
Technical Specifications...................................................81
Safety Statements............................................................83
Contacting Technical Support.........................................85
Warranty............................................................................86
Registration......................................................................94
D-Link DCS-2332L User Manual
4
Section 1: Product Overview
Product Overview
Package Contents
DCS-2332L Cloud Camera 2350 with Detachable Antenna
CAT5 Ethernet cable (Pre-Attached)
Power Adapter (Pre-Attached)
Quick Install Guide
If any of the above items are missing, please contact your reseller.
Note: Using a power supply with a different voltage than the one included with your product will cause damage and void the warranty for this product.
System Requirements
•
•
•
•
•
•
Computer with Microsoft Windows® 8/7/Vista®/XP; or Mac OS® X (10.6 or higher)
PC with 1.3GHz or above; at least 128MB RAM
Internet Explorer 7 or above , Firefox 8 or above, Safari 4, and Chrome 20 or above
Existing 10/100 Ethernet-based network or 802.11n wireless network
A microSD memory card (optional) is required for recording to onboard storage. SDHC Class 6 or above is recommended.
Broadband Internet connection
D-Link DCS-2332L User Manual
5
Section 1: Product Overview
Introduction
Congratulations on your purchase of the DCS-2332L Cloud Camera 2350. The DCS-2332L is a versatile and unique solution for
your small office or home. Unlike a standard webcam, the DCS-2332L is a complete system with a built-in CPU and web server
that transmits high quality video images for security and outdoor surveillance. The DCS-2332L can be accessed remotely and
controlled from any PC/Notebook over your local network or through the Internet via a web browser. The simple installation
and intuitive web-based interface offer easy integration with your Ethernet or 802.11n/g wireless network. The DCS-2332L
also comes with remote monitoring and motion detection features for a complete and cost-effective home security solution.
D-Link DCS-2332L User Manual
6
Section 1: Product Overview
Features
Simple to Use
The DCS-2332L is a stand-alone system with a built-in CPU, requiring no special hardware or software. The DCS-2332L supports both ActiveX mode
for Internet Explorer and Java mode for other browsers such as Firefox® and Safari®.
Supports a Variety of Platforms
Supporting TCP/IP networking, HTTP, and other Internet related protocols. The DCS-2332L can also be integrated easily into other Internet/Intranet
applications because of its standards-based features.
Web Configuration
Using a standard Web browser, administrators can configure and manage the Network Camera directly from its own Web page via Intranet or
Internet. This means you can access your DCS-2332L anytime, anywhere in the world.
Broad Range of Applications
With today’s high-speed Internet services, the Network Camera can provide the ideal solution for delivering live video images over the Intranet and
Internet for remote monitoring. The Network Camera allows remote access using a Web browser for live image viewing, and allows the administrator
to manage and control the Network Camera anytime, anywhere in the world. Many applications exist, including industrial and public monitoring
of homes, offices, banks, hospitals, child-care centers, and amusement parks.
Remote Monitoring Utility
The D-ViewCam application adds enhanced features and functionality for the Network Camera and allows administrators to configure and access
the Network Camera from a remote site via Intranet or Internet. Other features include image monitoring, recording images to a hard drive, viewing
up to 32 cameras on one screen and taking snapshots.
IR LED for Day and Night Functionality
The built-in infrared LEDs enable night time viewing of up to 16 feet (5 meters).
IP65 Weatherproof Housing
The DCS-2332L uses an IP65 weatherproof housing, allowing you to rest assured that in the toughest of conditions it will continue to provide
round-the-clock surveillance.
802.11n Wireless or Ethernet/Fast Ethernet Support
The DCS-2332L offers wireless 802.11n and Ethernet/Fast Ethernet connectivity, making the DCS-2332L easy to integrate into your existing
network environment. The DCS-2332L works with a 10Mbps Ethernet based network or 100Mbps Fast Ethernet based network for traditional wired
environments, and works with 802.11n routers or access points for added flexibility. The Site Survey feature also allows you to view and connect to
any available wireless networks.
D-Link DCS-2332L User Manual
7
Section 1: Product Overview
Hardware Overview
Front
8
1
2
3
4
1
Camera Lens
2
ICR Sensor
3
Microphone
4
PIR
5
IR LED
6
WPS Status LED
7
Power/Status LED
8
Antenna
D-Link DCS-2332L User Manual
5
6
7
Records video of the surrounding area
The IR-Cut Removable sensor measures the lighting conditions and switches
between color and infrared accordingly
Records audio from the surrounding area
Passive Infrared sensor for motion detection
Infrared LED illuminates the camera's field of view at night
Indicates the WPS connection status of the camera
Indicates the camera's current status
Outdoor wireless antenna
8
Section 1: Product Overview
Rear: External
1
6
2
3
7
8
4
9
5
6
1
Weatherproof Cover
2
Protective Cable Cover
3
Ethernet Cable
4
Speaker
5
Weatherproof Cover
6
Weatherproof Screw Covering
7
Power Cable
Connected to the included DC 5V power adapter
8
WPS Button
Press this button and then press the WPS button for five seconds on
your router to set up a wireless connection automatically
9
Adjustment Ring
D-Link DCS-2332L User Manual
Weatherproof protective panel
Weatherproof cable connection cover
RJ-45 Ethernet cable to connect to your network
Audio output
Weatherproof cover for the microSD Card slot and reset button
Weatherproof protective covering for enclosure screws
Tighten or loosen the adjustment ring to adjust the camera's position
9
Section 1: Product Overview
Rear: Internal
1
2
3
1
DC Power Connector
Connected to the included DC 5V power adapter
2
RJ-45 Ethernet Port
RJ-45 connector for Ethernet
3
Reset Button
4
MicroSD Memory Card Slot
D-Link DCS-2332L User Manual
4
Use a paperclip or similar tool to press and hold the recessed button for
10 seconds to reset the camera back to the factory default settings
Insert a microSD card for storing recorded images and video
10
Section 1: Product Overview
Removing the Top Panel
2
3
4
Step 1:
Place the camera face down on a non-slip flat surface.
Step 2:
Carefully pry out the two protective rubber screw coverings using a thin flat blade.
Step 3:
Undo the two screws using a Phillips screwdriver.
Step 4:
Lift off the protective panel.
Note: To ensure that the camera stays weatherproof, users are advised to ensure that all the rubber seals are secured firmly in place.
D-Link DCS-2332L User Manual
11
Section 1: Product Overview
Removing the Power Cable
2
Step 1:
Follow the steps outlined in Removing the Top Panel on page 11.
Step 2:
Unplug the power cable from the DC power connector.
Step 3:
Insert the rubber weatherproof plug ensuring it aligns with the space left by the power cable.
Step 4:
Follow the steps outlined in Reattaching the Top Panel on page 14.
Note: To avoid damage to the weatherproof aspects of the camera, users are advised to ensure the weatherproof plug is seated correctly.
D-Link DCS-2332L User Manual
12
Section 1: Product Overview
Replacing the Ethernet Cable
3
2
Step 1:
Follow the steps outlined in Removing the Top Panel on page 11.
Step 2:
Unplug the Ethernet cable from the Ethernet connector.
Step 3:
Carefully remove the weatherproof cable connection cover.
Step 4:
Attach the weatherproof cable connection cover to the new Ethernet cable.
Step 5:
Plug the new Ethernet cable into the Ethernet connector.
Step 6:
Follow the steps outlined in Reattaching the Top Panel on page 14.
Note: To avoid damage to the weatherproof aspects of the camera, users are advised not to remove the rear cable connection covering. To use a longer
Ethernet cable install a coupling adaptor.
D-Link DCS-2332L User Manual
13
Section 1: Product Overview
Reattaching the Top Panel
3
2
1
Step 1:
Seat the protective panel, ensuring a tight fit with the inlaid rubber seal.
Step 2:
Replace the two screws. Ensure that the screws are tightened firmly.
Step 3:
Firmly replace the protective rubber screw coverings.
Note: To ensure that the camera stays weatherproof, users are advised to ensure that all the rubber seals are secured firmly in place.
D-Link DCS-2332L User Manual
14
Section 1: Product Overview
Removing the Bottom Panel
Step 1:
Place the camera face down on a non-slip flat surface.
Step 2:
Carefully pry out the two protective rubber screw coverings using a thin flat blade.
2
Step 3:
Undo the two screws using a Phillips Screwdriver.
3
4
Step 4:
Lift off the protective panel.
Using the Reset Button
Step 1:
Follow the steps outlined above in Removing the Bottom Panel.
Step 2:
Using a paperclip or similar tool, press and hold the Reset Button for 10 seconds. This will
reset the device to it's factory settings.
Step 3:
Follow the steps outlined in Reattaching the Bottom Panel on page 16.
D-Link DCS-2332L User Manual
2
15
Section 1: Product Overview
Installing a microSD Memory Card
Step 1:
Follow the steps outlined in Removing the Bottom Panel on page 15.
Step 2:
Insert a microSD memory card into the slot, with the notch facing right.
Step 3:
Follow the steps outlined below in Reattaching the Bottom Panel.
2
Reattaching the Bottom Panel
Step 1:
Seat the protective panel, ensuring a tight fit with the inlaid rubber seal.
Step 2:
Replace the two screws. Ensure that the screws are tightened firmly.
Step 3:
Firmly replace the protective rubber screw coverings.
2
3
4
Note: To ensure that the camera stays weatherproof, users are advised to ensure that all the rubber
seals are secured firmly in place.
D-Link DCS-2332L User Manual
16
Section 1: Product Overview
Optional: WPS Wireless Connection
If your router supports WPS, you can use the WPS button on the camera to easily create a secure wireless connection to your
network.
To create a WPS connection:
Step 1
Locate the antennas included with your DCS-2332L and attach it to the antenna
connector located on the side of the Network Camera.
Step 2
Press and hold the WPS button for approximately 5-6 seconds. The blue WPS
status LED on the front panel will blink.
Step 3
Within 60 seconds press the WPS button on your router. On some routers, you
may need to log into the web interface and click on an on-screen button to
activate the WPS feature. If you are not sure where the WPS button is on your
router, please refer to your router’s user manual.
1
WPS Button
2
The DCS-2332L will automatically create a wireless connection to your router.
While connecting, the status LED will flash. When the connection process is
complete, the status LED will turn solid.
Note: If your router does not support WPS, you can still use the wired connection
method on the previous page. After Zero Configuration setup is complete, your router's
wireless settings will be automatically transferred to the camera.
D-Link DCS-2332L User Manual
17
ATE
Section 2: Installation
Installation
Zero Configuration Setup
If you have a mydlink-enabled Cloud Router, you can take advantage of Zero Configuration. Zero Configuration automatically
configures your camera's settings for you and adds it to your mydlink account automatically. This type of setup allows you to
set up your camera by simply plugging it in and connecting it to your router.
Connect your camera to your mydlink-enabled Cloud Router and Zero Configuration will automatically configure your
DCS‑2332L and automatically add the camera to your mydlink account. When setup is complete you can remotely access your
camera from the www.mydlink.com website to manage and monitor your DCS-2332L.
Connect the Ethernet Cable
Connect the free end of the pre-attached Ethernet cable to your network.
Attach the External Power Supply
Attach the external power supply to your wall outlet or power strip.
D-Link DCS-2332L User Manual
18
Section 2: Installation
Check Your mydlink Account
Open a web browser and login to your mydlink account. The mydlink page will
check for new devices and display a New device Found! pop-up notification in
the bottom-left corner. Click the notification to continue.
A summary and confirmation notification will appear with the automatically
configured details. Make a note of the details and click OK to add the camera to
your account.
DCS-2332L
D-Link DCS-2332L User Manual
19
Section 2: Installation
The mydlink Live View tab for your camera will appear.
If you wish to connect your camera to your router wirelessly, you can simply
disconnect the Ethernet cable and move the camera to its intended location. Your
router's wireless settings have been automatically transferred to the camera and
no further configuration is required.
Your camera is now setup and you can skip to mydlink on page 31 to learn more
about the mydlink features of this camera, or to Configuration on page 40 for
advanced configuration of your camera.
D-Link DCS-2332L User Manual
20
Section 2: Installation
Camera Setup Wizard
Windows Users
The Setup Wizard is available for download at http://www.mydlink.com/download. Click your camera model and then, under Wizard,
click the link of the version (Windows) you want to download.
Double-click the file to launch. Simply click Set up your Cloud Camera to go through the Setup Wizard. The wizard will guide
you step-by-step through the installation process, from connecting your hardware to configuring your camera and registering
it with your mydlink account.
D-Link DCS-2332L User Manual
21
Section 2: Installation
Select your preferred language for the installation from the drop-down menu
and click on Start to proceed.
Locate the pre-attached Ethernet and power cables on the rear of your camera.
Click Next to continue.
D-Link DCS-2332L User Manual
22
Section 2: Installation
Connect the Ethernet cable to a router.
Click Next to continue..
Attach the external power supply to your wall outlet or power strip.
Click Next to continue.
D-Link DCS-2332L User Manual
23
Section 2: Installation
The LED on the front of the DCS-2332L will blink, then turn solid green once it
successfully connects to your network. Click Next to proceed.
If the LED continues to blink, check your connections or click on the "What should
I do if the LED stays red?" link for more information.
Select your camera from the list, then click Next. If you have multiple cameras,
you can identify them by the MAC ID printed on the label on the back of your
camera.
Click Next to continue.
D-Link DCS-2332L User Manual
24
Section 2: Installation
If you wish to remove the camera from a previously registered mydlink account,
press and hold the Reset button on the rear panel for at least 10 seconds and
click Retry to restart the Setup Wizard.
After you have selected your camera from the list, you will be asked to
create and confirm a password for it. The password is case sensitive and
must contain at least six letters.
Click Next to continue.
D-Link DCS-2332L User Manual
25
Section 2: Installation
Click Next to continue.
Complete the mydlink account registration with your details and make sure to
check the I accept mydlink terms and conditions box.
Click Next to continue.
D-Link DCS-2332L User Manual
26
Section 2: Installation
If you already have a mydlink account, enter your login details and click Next to
proceed.
Confirm your mydlink account details and give the camera a unique
name and click Finish.
D-Link DCS-2332L User Manual
27
Section 2: Installation
Confirm your camera login details and IP address details and click Done.
Your DCS-2332L camera is now setup. Log on to your mydlink account and explore
the exciting benefits available to you.
DCS-2332L
You can skip to mydlink on page 31 to learn more about the mydlink features of
this camera, or to Configuration on page 40 for advanced configuration of your
camera.
D-Link DCS-2332L User Manual
28
Section 2: Installation
Mac Users
Insert the Installation CD into your computer’s CD-ROM drive. On the desktop, open your CD drive and
double-click on the SetupWizard file.
After about 20-30 seconds, the Setup Wizard will open, which will guide you step-by-step through the installation process, from
connecting your hardware to configuring your camera and registering it with your mydlink account.
D-Link DCS-2332L User Manual
29
Section 2: Installation
Manual Hardware Installation
If you wish to set up your camera without using the Camera Setup Wizard, please follow these steps.
Note: In order to use the mydlink features of this product, you will need to go through the Camera Setup Wizard.
Connect the Ethernet Cable
Using the pre-attached Ethernet cable, connect the free end to your network.
Attach the External Power Supply
Attach the external power supply to your wall outlet or power strip.
D-Link DCS-2332L User Manual
30
Section 3: mydlink
mydlink
After registering your DCS-2332L camera with a mydlink account in the Camera Installation Wizard, you will be able to remotely
access your camera from the www.mydlink.com website. After signing in to your mydlink account, you will see a screen similar
to the following:
DCS-2332L
D-Link DCS-2332L User Manual
31
Section 3: mydlink
Camera Status
Here you can see the online status of each of your cameras. Your online status may be one of the following:
A green check mark indicates that your camera is online and ready to use.
A yellow exclamation point indicates that your camera is online, but the camera password
has changed. You will need to enter your new camera password to access your camera
again.
A red X indicates that your camera is offline and currently cannot be accessed remotely.
If your camera is offline, try the following:
• Check to make sure that the Internet connection to your camera is working properly.
• Try restarting your Internet router.
• Check your camera’s cable connections and make sure they are secure.
• Check to make sure that the LED on your camera is lit solid green.
If you still cannot access your camera, reset your camera and run the Camera Installation Wizard again from the CD-ROM
included in your package.
D-Link DCS-2332L User Manual
32
Section 3: mydlink
Live Video
In the main part of the screen, the Live Video tab will be selected by default. If the camera is available, a live video feed will be
displayed. Video will be shown at VGA resolution (640x480) if viewing your camera from a PC on the same local network, or at
QVGA resolution (320x240) if viewing your camera from a PC on a remote network.
DCS-2332L
D-Link DCS-2332L User Manual
33
Section 3: mydlink
Playback
The Playback tab allows you to review pre-recorded footage captured to the
microSD card.
DCS-2332L
Select the date of the footage you wish to preview from the drop-down menu,
then choose from the recordings available for that date.
DCS-2332L
D-Link DCS-2332L User Manual
34
Section 3: mydlink
Settings
The Settings tab contains several options for you to control how your DCS-2332L
operates.
DCS-2332L
Camera Name: Click on the Edit button to change how the camera name appears.
mydlink No: This is the unique mydlink number for your device.
Model name: This shows the model name of the camera.
MAC: The shows the Media Access Control (MAC) address of the camera.
Camera Activated on: The date the camera was registered to the mydlink service.
Event Notification
Settings: E-mail notification of events can be switched on or off.
Recording Settings: Each of the recording settings will open a further menu.
D-Link DCS-2332L User Manual
35
Section 3: mydlink
Recording Settings
Record video clips when Select this option to enable the automatic recording when motion
motion is detected: is detected.
Add Detection Area: Click on this icon to draw areas that
will trigger automatic recording when motion is detected.
Remove Detection Area: Click on this icon to erase areas
from regions that trigger automatic recording when
motion is detected.
Clear Detection Area: This will remove all detection
areas
Refresh Snapshot: This will refresh the current snapshot
of the monitored area.
Increase/Decrease Sensitivity: Increase the motion
detection sensitivity
E-mail Notification: Toggles e-mail notification on or off.
Video Clips Recording In the event that the microSD card cannot store further recordings,
Mode: the user can choose to record over previous recordings or to be
notified and cease recording.
D-Link DCS-2332L User Manual
36
Section 3: mydlink
Record Video Clips by This option enables either continuous or recurring scheduled
Schedule: recording.
E-mail Notification: Toggles e-mail notification on or off.
Video Clips Recording In the event that the microSD card cannot store further recordings,
Mode: the user can choose to record over previous recordings or to be
notified and cease recording.
D-Link DCS-2332L User Manual
37
Section 3: mydlink
Advanced Settings
Show password: Checking this box will show the password.
Advanced Settings: Clicking on the Advanced Settings button will open a secondary
window allowing full configuration of the DCS-2332L.
DCS-2332L
D-Link DCS-2332L User Manual
38
Section 3: mydlink
Events
Record video clips
when motion is Select this option to enable the automatic recording when motion
detected: is detected.
DCS-2332L
Mark Page as Read: Clicking this button will mark the
current page of event notifications as read.
Mark all as Read: Clicking this button will mark all event
notifications as read.
D-Link DCS-2332L User Manual
39
Section 4: Configuration
Configuration
Using the Configuration Interface
After completing the Camera Installation Wizard, you are ready to use your camera. The camera’s built-in Web configuration utility is designed to
allow you to easily access and configure your DCS-2332L. At the end of the wizard, enter the IP address of your camera into a web browser, such as
Mozilla Firefox. To log in, use the user name admin and the password you created in the Installation Wizard. If you did not create a password, the
default password is blank. After entering your password, click OK.
D-Link DCS-2332L User Manual
40
Section 4: Configuration
Live Video
This section shows your camera’s live video. You may select any of the available icons listed below to operate the camera. You may also select your
language using the drop-down menu on the left side of the screen.
You can zoom in and out on the live video image using your mouse. Right-click to zoom out or left-click to zoom in on the image.
SD Status: This option displays the status of the microSD card. If no microSD
card has been inserted, this screen will display the message "Card
Invalid."
Motion Trigger
Indicator
This indicator will change color when a trigger event occurs.
Stop
Note: The video motion feature for your camera must be
enabled.
When a recording is in progress, this indicator will change
color.
This control pad can be used to electronically pan, tilt, and
zoom (ePTZ) within the camera's predefined view area, if one
has been defined.
Starts the automatic panning function. The Region of Interest
(ROI) will pan back and forth within the Field of View (FOV).
Stops the camera ePTZ motion.
Preset Path
Starts the camera's motion along a predefined path.
Recording
Indicator
Control Pad
Auto Pan
ePTZ Speed: You may select a value between 0 and 64. 0 is the slowest and 64
is the fastest.
D-Link DCS-2332L User Manual
41
Section 4: Configuration
Global View: This window indicates the total Field of View (FOV) of the camera.
The red box indicates the visible Region of Interest (ROI).
Language: You may select the interface language using this menu.
Video Profile 1
Record a Video Clip
Video Profile 2
Set a Storage Folder
Video Profile 3
Listen/Stop Audio In (from microphone)
Full screen mode
Start/Stop Audio Out (to speaker)
Take a Snapshot
Go To If any presets have been defined, selecting a preset from this list
(Preset List): will display it.
D-Link DCS-2332L User Manual
42
Section 4: Configuration
Setup
Setup Wizard
To configure your Network Camera, click Internet Connection Setup Wizard.
Alternatively, you may click Manual Internet Connection Setup to manually
configure your Network Camera and skip to Network Setup on page 49.
DCS-2332L
To quickly configure your Network Camera’s motion detection settings, click Motion
Detection Setup Wizard. If you want to enter your settings without running the
wizard, click Manual Motion Detection Setup and skip to Motion Detection on page
60.
D-Link DCS-2332L User Manual
43
Section 4: Configuration
Internet Connection Setup Wizard
This wizard will guide you through a step-by-step process to configure your new D-Link
Camera and connect the camera to the Internet. Click Next to continue.
Note: Select DHCP if you are unsure of which settings to choose.
Click Next to continue.
D-Link DCS-2332L User Manual
44
Section 4: Configuration
Select Static IP if your Internet Service Provider (ISP) has provided you with connection
settings or if you wish to set a static address within your home network. Enter the correct
configuration information and click Next to continue.
If you are using PPPoE, select Enable PPPoE and enter your user name and password,
otherwise click Next to continue.
If you have a Dynamic DNS account and would like the camera to update your IP address
automatically, select Enable DDNS and enter your host information. Click Next to continue.
Enter a name for your camera and click Next to continue.
DCS-2332L
D-Link DCS-2332L User Manual
45
Section 4: Configuration
Configure the correct time to ensure that all events will be triggered as scheduled. Click Next
to continue.
If you have selected DHCP, you will see a summary of your settings, including the camera's IP
address. Please write down all of this information as you will need it in order to access your
camera.
DCS-2332L
Click Apply to save your settings.
D-Link DCS-2332L User Manual
46
Section 4: Configuration
Motion Detection Setup Wizard
This wizard will guide you through a step-by-step process to configure your camera's motion
detection functions.
Click Next to continue.
Step 1
This step will allow you to enable or disable motion detection, specify the detection sensitivity,
and adjust the camera’s ability to detect movement.
You may specify whether the camera should capture a snapshot or a video clip when motion
is detected.
Please see the Motion Detection section on page 60 for information about how to configure
motion detection.
Step 2
This step allows you to enable motion detection based on a customized schedule. Specify
the day and hours that you want motion detection activated. You may also choose to always
record motion.
D-Link DCS-2332L User Manual
47
Section 4: Configuration
Step 3
This step allows you to specify how you will receive event notifications from
your camera. You may choose to receive notifications via e-mail or FTP or disable
notifications.
Please enter the relevant information for your e-mail or FTP account.
Click Next to continue.
Step 4
You have completed the Motion Detection Wizard.
Please verify your settings and click Apply to save them.
Please wait a few moments while the camera saves your settings and restarts.
D-Link DCS-2332L User Manual
48
Section 4: Configuration
Network Setup
Use this section to configure the network connections for your camera. All relevant information must be entered accurately. After making any
changes, click the Save Settings button to save your changes.
LAN Settings: This section lets you configure settings for your local
area network.
DCS-2332L
DHCP: Select this connection if you have a DHCP server running
on your network and would like your camera to obtain
an IP address automatically.
If you choose DHCP, you do not need to fill out the IP
address settings.
Static IP Client: You may obtain a static or fixed IP address and other
network information from your network administrator
for your camera. A static IP address may simplify access
to your camera in the future.
IP address: Enter the fixed IP address in this field.
Subnet mask: This number is used to determine if the destination is in
the same subnet. The default value is 255.255.255.0.
Default router: The gateway used to forward frames to destinations in a
different subnet. Invalid gateway settings may cause the
failure of transmissions to a different subnet.
Primary DNS: The primary domain name server (DNS) translates names
to IP addresses.
Secondary DNS: The secondary DNS acts as a backup to the primary DNS.
D-Link DCS-2332L User Manual
49
Section 4: Configuration
Enable UPnP presentation: Enabling this setting allows your camera to be configured
as a UPnP device on your network.
Enable UPnP port forwarding: Enabling this setting allows the camera to add port
forwarding entries into the router automatically on a
UPnP capable network.
Enable PPPoE: Enable this setting if your network uses PPPoE.
User Name / Password: Enter the user name and password for your PPPoE
account. Re-enter your password in the Confirm Password
field. You may obtain this information from your ISP.
HTTP Port: The default port number is 80.
Access Name for Stream 1~3: The default name is video#.mjpg, where # is the number
of the stream.
HTTPS Port: You may use a PC with a secure browser to connect to
the HTTPS port of the camera. The default port number
is 443.
Authentication: Depending on your network security requirements, the Network Camera provides two types of security
settings for streaming via RTSP protocol: Disable and Digest. If Digest authentication is selected, user credentials
are encrypted using MD5 algorithm, thus providing better protection against unauthorized access.
RTSP Port: The port number that you use for RTSP streaming to mobile devices, such as mobile phones or PDAs. The
default port number is 554. You may specify the address of a particular stream. For instance, live1.sdp can be
accessed at rtsp://x.x.x.x/video1.sdp where the x.x.x.x represents the IP address of your camera.
Access name for stream 1 ~ 3: This Network Camera supports multiple streams simultaneously. The access name is used to differentiate the
streaming source (video profile).
D-Link DCS-2332L User Manual
50
Section 4: Configuration
CoS Settings: Enabling the Class of Service setting implements
a best-effort policy without making any bandwidth
reservations.
QoS Settings: Enabling QoS allows you to specify a traffic priority
policy to ensure a consistent Quality of Service during
busy periods. If the Network Camera is connected to a
router that itself implements QoS, the router's settings
will override the QoS settings of the camera.
IPv6: Enable the IPv6 setting to use the IPv6 protocol. Enabling
the option allows you to manually set up the address,
specify an optional IP address, specify an optional router
and an optional primary DNS.
Multicast: The DCS-2332L allows you to multicast each of the
available streams via group address and specify the TTL
value for each stream. Enter the port and TTL settings
you wish to use if you do not want to use the defaults.
D-Link DCS-2332L User Manual
51
Section 4: Configuration
Wireless Setup
This section allows you to set up and configure the wireless settings on your camera. After making any changes, click the Save Settings button to
save your changes.
Site Survey: Click the Rescan button to scan for available wireless
networks. After scanning, you can use the drop-down
box to select an available wireless network. The related
information (SSID, Wireless Mode, Channel, Authentication,
Encryption) will be automatically filled in for you.
DCS-2332L
SSID: Enter the SSID of the wireless access point you wish to
use.
Wireless Mode: Use the drop-down box to select the mode of the
wireless network you wish to connect to. Infrastructure
is normally used to connect to an access point or router.
Ad-Hoc is usually used to connect directly to another
computer.
Channel: If you are using Ad-Hoc mode, select the channel of the
wireless network you wish to connect to or select Auto.
Authentication: Select the authentication you use on your wireless
network: Open, Shared, WPA-PSK or WPA2-PSK.
Encryption: If you use WPA-PSK or WPA2-PSK authentication, you
will need to specify whether your wireless network
uses TKIP or AES encryption. If you use Open or Shared
authentication, WEP encryption should be the setting.
Default Key: If you use WEP, WPA-PSK or WPA2-PSK authentication,
enter the Key (or password) used for your wireless
network.
D-Link DCS-2332L User Manual
52
Section 4: Configuration
Dynamic DNS
DDNS (Dynamic Domain Name Server) will hold a DNS host name and synchronize the public IP address of the modem when it has been modified.
A user name and password are required when using the DDNS service. After making any changes, click the Save Settings button to save your
changes.
Enable DDNS: Select this checkbox to enable the DDNS function.
Server Address: Select your Dynamic DNS provider from the pull down
menu or enter the server address manually.
DCS-2332L
Host Name: Enter the host name of the DDNS server.
User Name: Enter the user name or e-mail used to connect to your
DDNS account.
Password: Enter the password used to connect to your DDNS
server account.
Timeout: Enter the DNS timeout values you wish to use.
Status: Indicates the connection status, which is automatically
determined by the system.
D-Link DCS-2332L User Manual
53
Section 4: Configuration
Image Setup
In this section, you may configure the video image settings for your camera. A preview of the image will be shown in the Live Video window.
Enable Privacy Mask: The Privacy Mask setting allows you to specify up to three
rectangular areas on the camera's image to be blocked/
excluded from recordings and snapshots.
DCS-2332L
You may click and drag the mouse cursor over the
camera image to draw a mask area. Right clicking on the
camera image brings up the following menu options:
Disable All: Disables all mask areas.
Enable All: Enables all mask areas.
Reset All: Clears all mask areas.
Anti Flicker: If the video flickers, try enabling this setting.
Mirror: This will mirror the image horizontally.
Flip: This will flip the image vertically. When turning Flip on,
you may want to consider turning Mirror on as well.
Power Line: Select the frequency used by your power lines to avoid
interference or distortion.
White Balance: Use the drop-down box to change white balance settings
to help balance colors for different environments. You
can choose from Auto, Outdoor, Indoor, Fluorescent,
and Push Hold.
D-Link DCS-2332L User Manual
54
Section 4: Configuration
Exposure Mode: Changes the exposure mode. Use the drop-down
box to set the camera for Indoor, Outdoor, or Night
environments, or to Moving to capture moving objects.
The Low Noise option will focus on creating a highquality picture without noise. You can also create three
different custom exposure modes. The Max Gain setting
will allow you to control the maximum amount of gain
to apply to brighten the picture.
Denoise: This setting controls the amount of noise reduction that
will be applied to the picture.
Brightness: Adjust this setting to compensate for backlit subjects.
Contrast: Adjust this setting to alter the color intensity/strength.
Saturation: This setting controls the amount of coloration, from
grayscale to fully saturated.
Sharpness: Specify a value from 0 to 8 to specify how much
sharpening to apply to the image.
Reset Default: Click this button to reset the image to factory default
settings.
D-Link DCS-2332L User Manual
55
Section 4: Configuration
Audio and Video
You may configure up to three video profiles with different settings for your camera. Hence, you may set up different profiles for your computer
and mobile display. In addition, you may also configure the two-way audio settings for your camera. After making any changes, click the Save
Settings button to save your changes.
Aspect ratio: Set the aspect ratio of the video to 4:3 standard or 16:9
widescreen.
DCS-2332L
Mode: Set the video codec to be used to JPEG, MPEG-4, or
H.264.
Frame size / View window area: Frame size determines the total capture resolution, and
View window area determines the Live Video viewing
window size. If the Frame size is larger than the Live
Video size, you can use the ePTZ controls to look around.
16:9 1280 x 800, 1280 x 720, 800 x 450,
640 x 360, 480 x 270, 320 x 176,
176 x 144
4:3
1024 x 768, 800 x 600, 640 x 480,
480 x 360, 320 x 240, 176 x 144
Note: If your View window area is the same as your Frame
size, you will not be able to use the ePTZ function.
Maximum frame rate: A higher frame rate provides smoother motion for videos
but requires more bandwidth. Lower frame rates will
result in stuttering motion but require less bandwidth.
D-Link DCS-2332L User Manual
56
Section 4: Configuration
Video Quality: This limits the maximum frame rate, which can be
combined with the Fixed quality option to optimize
the bandwidth utilization and video quality. If fixed
bandwidth utilization is desired, regardless of the video
quality, choose Constant bit rate and select the desired
bandwidth.
DCS-2332L
Constant bit rate: The bps will affect the bit rate of the video recorded
by the camera. Higher bit rates result in higher video
quality.
Fixed quality: Select the image quality level for the camera to try to
maintain. High quality levels will result in increased bit
rates.
Audio in off: Selecting this checkbox will mute incoming audio.
Audio in gain level: This setting controls the amount of gain applied to
incoming audio to increase its volume.
Audio out off: Selecting this checkbox will mute outgoing audio.
Audio out volume level: This setting controls the amount of gain applied to
outgoing audio to increase its volume.
D-Link DCS-2332L User Manual
57
Section 4: Configuration
Preset
This screen allows you to set preset points for the ePTZ function of the camera, which allows you to look around the camera's viewable area by
using a zoomed view. Presets allow you to quickly go to and view a specific part of the area your camera is covering. Also, you can create preset
sequences which will automatically change the camera's view between the different presets according to a defined order and timing you can set.
Note: If your View window area is the same as your Frame size, you will not be able to use the ePTZ function.
Video Profile: This selects which video profile to use.
ePTZ Speed: You may select a value between 0 and 64. 0 is the slowest
and 64 is the fastest.
DCS-2332L
Arrow Buttons and Home Use these buttons to move to a specific part of the
Button: viewing area, which you can then set as a preset. Click
the "Home" button to return to the center of the viewing
area.
Input Preset Name: Enter the name of the preset you want to create, then
click the Add button to make a new preset. If an existing
preset has been selected from the Preset List, you can
change its name by typing in a new name, then clicking
the Rename button.
Preset List: Click this drop-down box to see a list of all the presets
that have been created. Select one, then click the GoTo
button to change the displayed camera view to the
preset. Clicking the Remove button will delete the
currently selected preset.
Preset Sequence: This section allows you to create a preset sequence,
which automatically moves the camera's view between
a set of preset views.
D-Link DCS-2332L User Manual
58
Section 4: Configuration
Preset List: To add a preset to the sequence, select it from the dropdown box at the bottom of this window, set the
Dwell time to determine how long the camera view will
stay at that preset, then click the Add button. The preset
name will appear in the list, followed by the dwell time
to view that preset for.
You can rearrange your presets in the sequence by
selecting a preset in the sequence, then clicking the
"Arrow" buttons to move it higher or lower in the current
sequence.
Clicking the "Trash Can" button will remove the currently
selected preset from the sequence.
If you want to change the dwell time for a preset, select
it from the list, enter a new dwell time, then click the
Update button.
D-Link DCS-2332L User Manual
59
Section 4: Configuration
Motion Detection
Enabling Video Motion will allow your camera to use the motion detection feature. You may draw a finite motion area that will be used for monitoring.
After making any changes, click the Save Settings button to save your changes.
Enable Video Motion: Select this box to enable the motion detection feature
of your camera.
DCS-2332L
Sensitivity: Specifies the measurable difference between two
sequential images that would indicate motion. Please
enter a value between 0 and 100.
Percentage: Specifies the amount of motion in the window being
monitored that is required to initiate an alert. If this is set
to 100%, motion detected within the whole window will
trigger a snapshot.
Draw Motion Area: Draw the motion detection area by dragging your mouse
in the window (indicated by the red square).
Erase Motion Area: To erase a motion detection area, simply click on the red
square that you wish to remove.
Right clicking on the camera image brings up the
following menu options:
Select All: Draws a motion detection area over the
entire screen.
Clear All: Clears any motion detection areas that
have been drawn.
Restore: Restores the previously specified motion
detection areas.
D-Link DCS-2332L User Manual
60
Section 4: Configuration
Time and Date
This section allows you to automatically or manually configure, update and maintain the internal system clock for your camera. After making any
changes, click the Save Settings button to save your changes.
Time Zone: Select your time zone from the drop-down menu.
Enable Daylight-Saving: Select this to enable Daylight-Saving Time.
DCS-2332L
Auto Daylight-Saving: Select this option to allow your camera to configure the
Daylight-Saving settings automatically.
Set Date and Time Manually: Selecting this option allows you to configure the
Daylight-Saving date and time manually.
Offset: Sets the amount of time to be added or removed when
Daylight-Saving is enabled.
Synchronize with NTP Server: Enable this feature to obtain time automatically from an
NTP server.
NTP Server: Network Time Protocol (NTP) synchronizes the Network
Camera with an Internet time server. Choose the one
that is closest to your location.
Set the Date and Time Manually: This option allows you to set the time and date manually.
Copy Your Computer's Time
Settings: This will synchronize the time information from your PC.
D-Link DCS-2332L User Manual
61
Section 4: Configuration
Event Setup
In a typical application, when motion is detected, the DCS-2332L sends images to a FTP server or via e-mail as notifications. As shown in the
illustration below, an event can be triggered by many sources, such as motion detection or external digital input devices. When an event is
triggered, a specified action will be performed. You can configure the Network Camera to send snapshots or videos to your e-mail address or FTP
site.
Action
Event Condition
ex.
Motion detection,
Periodically, Digital input,
System reboot
Media
(what to send)
ex.
Snapshot, Video Clips
Server
(where to send)
ex.
Email, FTP
To start plotting an event, it is suggested to configure server and media columns first so that the Network Camera will know what action shall be
performed when a trigger is activated.
D-Link DCS-2332L User Manual
62
Section 4: Configuration
The Event Setup page includes four different sections:
• Event
• Server
• Media
• Recording
DCS-2332L
1. To add a new item (event, server or media) click Add. A screen will appear and allow you
to update the fields accordingly.
2. To delete the selected item from the pull-down menu, click Delete.
3. Click on the item name to pop up a window for modifying.
D-Link DCS-2332L User Manual
63
Section 4: Configuration
Add Server
You can configure up to five servers to save snapshots and/or video to. After making any
changes, click the Save Settings button to save your changes.
DCS-2332L
Server Name: Enter the unique name of your server.
E-mail: Enter the configuration for the target e-mail server
account.
FTP: Enter the configuration for the target FTP server account.
Network Storage: Specify a network storage device. Only one network
storage device is supported.
microSD Card: Use the camera's onboard microSD card storage.
D-Link DCS-2332L User Manual
64
Section 4: Configuration
Add Media
There are three types of media - Snapshot, Video Clip and System Log. After making any
changes, click the Save Settings button to save your changes.
DCS-2332L
Media Name: Enter a unique name for media type you want to create.
Snapshot: Select this option to set the media type to Snapshots.
Source: Set the video profile to use as the media source. Refer
to Audio and Video on page 56 for more information on
video profiles.
Send pre-event image(s) [0~4]: Set the number of pre-event images to take. Pre-event
images are images taken before the main event snapshot
is taken.
Send post-event image(s) [0~7]: Set the number of post-event images to take. Post-event
images are images taken after the main event snapshot
is taken. You can set up to seven post-event images to
be taken.
File name prefix: The prefix name will be added on the file name.
Add date and time suffix to file
name: Check to add timing information as file name suffix.
D-Link DCS-2332L User Manual
65
Section 4: Configuration
Video clip: Select this option to set the media type to Video Clips.
Source: Set the video profile to use as the media source. Refer
to Audio and Video on page 56 for more information on
video profiles.
DCS-2332L
Pre-event recording: This sets how many seconds to record before the main
event video clip starts. You can record up to four seconds
of pre-event video.
Maximum duration: Set the maximum length of video to record for your
video clips.
Maximum file size: Set the maximum file size to record for your video clips.
File name prefix: This is the prefix that will be added to the filename of
saved video clips.
System log: Select this option to set the media type to System Logs.
This will save the event to the camera system log, but
will not record any snapshots or video.
D-Link DCS-2332L User Manual
66
Section 4: Configuration
Add Event
Create and schedule up to two events with their own settings here. After making any changes, click the Save Settings button to save your changes.
Event name: Enter a name for the event.
Enable this event: Select this box to activate this event.
Priority: Set the priority for this event. The event with higher
priority will be executed first.
Delay: Select the delay time before checking the next event. It
is being used for both events of motion detection and
digital input trigger.
Trigger: Specify the input type that triggers the event.
Video Motion Detection: Motion is detected during live video monitoring. Select
the windows that need to be monitored.
Periodic: The event is triggered in specified intervals. The trigger
interval unit is in minutes.
System Boot: Triggers an event when the system boots up.
Network Lost: Triggers an event when the network connection is lost.
Passive Infrared Sensor: Triggers an event when the Passive Infrared Sensor (PIR) is
activated by moving objects, even in dark environment.
D-Link DCS-2332L User Manual
67
Section 4: Configuration
Time: Select Always or enter the time interval.
Server: Specify the location where the event information should
be saved to.
D-Link DCS-2332L User Manual
DCS-2332L
68
Section 4: Configuration
Add Recording
Here you can configure and schedule the recording settings. After making any changes, click the Save Settings button to save your changes.
Recording entry name: The unique name of the entry.
Enable this recording: Select this to enable the recording function.
DCS-2332L
Priority: Set the priority for this entry. The entry with a higher
priority value will be executed first.
Source: The source of the stream.
Recording schedule: Scheduling the recording entry.
Recording settings: Configuring the setting for the recording.
Destination: Select the folder where the recording file will be stored.
Total cycling recording size: Please input a HDD volume between 1MB and 2TB for
recording space. The recording data will replace the
oldest record when the total recording size exceeds this
value. For example, if each recording file is 6MB, and the
total cyclical recording size is 600MB, then the camera
will record 100 files in the specified location (folder) and
then will delete the oldest file and create new file for
cyclical recording.
Please note that if the free HDD space is not enough, the
recording will stop. Before you set up this option please
make sure your HDD has enough space. It is better to not
save other files in the same folder as recording files.
D-Link DCS-2332L User Manual
69
Section 4: Configuration
Size of each file for recording: If this is selected, files will be separated based on the file
size you specify.
DCS-2332L
Time of each file for recording: If this is selected, files will be separated based on the
maximum length you specify.
File Name Prefix: The prefix name will be added on the file name of the
recording file(s).
D-Link DCS-2332L User Manual
70
Section 4: Configuration
microSD Card
Here you may browse and manage the recorded files which are stored on the microSD card.
Format microSD Card: Click this icon to format the microSD card and create
Picture & Video folders.
DCS-2332L
View Recorded Picture: If the picture files are stored on the microSD card, click
on the Picture folder and choose the picture file you
would like to view.
Playback Recorded Video: If video files are stored on the microSD card, click on the
Video folder and choose the video file you would like to
view.
Refresh: Reloads the file and folder information from the microSD
card.
D-Link DCS-2332L User Manual
71
Section 4: Configuration
Advanced
ICR and IR
Here you can configure the ICR and IR settings. An IR (Infrared) Cut-Removable (ICR) filter can be disengaged for increased sensitivity in low light
environments.
Automatic: The Day/Night mode is set automatically. Generally, the
camera uses Day mode and switches to Night mode
when needed.
DCS-2332L
Day Mode: Day mode enables the IR Cut Filter.
Night Mode: Night mode disables the IR Cut Filter.
Schedule Mode: Set up the Day/Night mode using a schedule. The camera
will enter Day mode at the starting time and return to
Night mode at the ending time.
IR Light Control: The camera can enable or disable the IR (infrared) light
according to your preferences. This setting provides
additional controls depending on your specific application.
Off: The IR light will always be off.
On: The IR light will always be on.
Sync: The IR light will turn on when the ICR sensor is on.
Schedule: The IR light will turn on or off according to the schedule
that you specify below.
D-Link DCS-2332L User Manual
72
Section 4: Configuration
HTTPS
This page allows you to install and activate an HTTPS certificate for secure access to your camera. After making any changes, click the Save Settings
button to save your changes.
Enable HTTPS Secure
Connection: Enable the HTTPS service.
DCS-2332L
Create Certificate Method: Choose the way the certificate should be created. Three
options are available:
Create a self-signed certificate automatically
Create a self-signed certificate manually
Create a certificate request and install
Status: Displays the status of the certificate.
Note: The certificate cannot be removed while the HTTPS is still
enabled. To remove the certificate, you must first uncheck
Enable HTTPS secure connection.
D-Link DCS-2332L User Manual
73
Section 4: Configuration
Access List
Here you can set access permissions for users to view your DCS-2332L.
Allow list: The list of IP addresses that have the access right to the
camera.
DCS-2332L
Start IP address: The starting IP address of the devices (such as a computer)
that have permission to access the video of the camera.
Click Add to save the changes made.
Note: A total of seven lists can be configured for each.
End IP address: The ending IP address of the devices (such as a computer)
that have permission to access the video of the camera.
Delete allow list: Remove the customized setting from the Allow List.
Deny list: The list of IP addresses that have no access rights to the
camera.
Delete deny list: Remove the customized setting from the Deny List.
For example:
When the range of the Allow List is set from 1.1.1.0 to
192.255.255.255 and the range of the Deny List is set from
1.1.1.0 to 170.255.255.255. Only users with IPs located
between 171.0.0.0 and 192.255.255.255 can access the
Network Camera.
D-Link DCS-2332L User Manual
Allow
List
Deny
List
74
Section 4: Configuration
System
In this section, you may backup, restore and reset the camera configuration, or reboot the camera.
Save To Local Hard Drive: You may save your current camera configuration as a file
on your computer.
DCS-2332L
Local From Local Hard Drive: Locate a pre-saved configuration by clicking Browse and
then restore the pre-defined settings to your camera by
clicking Load Configuration.
Restore to Factory Default: You may reset your camera and restore the factory
settings by clicking Restore Factory Defaults.
Reboot Device: This will restart your camera.
D-Link DCS-2332L User Manual
75
Section 4: Configuration
Maintenance
Device Management
You may modify the name and administrator’s password of your camera, as well as add and manage the user accounts for accessing the camera.
You may also use this section to create a unique name and configure the On-Screen Display (OSD) settings for your camera.
Admin Password Setting: Set a new password for the administrator’s account.
Add User Account: Add new user account.
DCS-2332L
User Name: The user name for the new account.
Password: The password for the new account.
User List: All the existing user accounts will be displayed here. You
may delete accounts included in the list, but you may
want to reserve at least one as a guest account.
Camera Name: Create a unique name for your camera that will be added
to the file name prefix when creating a snapshot or a
video clip.
Enable OSD: Select this option to enable the On-Screen Display (OSD)
feature for your camera.
Label: Enter a label for the camera, which will be shown on the
OSD when it is enabled.
Show Time: Select this option to enable the time-stamp display on
the video screen.
D-Link DCS-2332L User Manual
76
Section 4: Configuration
Firmware Upgrade
The camera's current firmware version will be displayed on this screen. You may visit the D-Link Support Website to check for the latest available
firmware version.
To upgrade the firmware on your DCS-2332L, please download and save the latest firmware version from the D-Link Support Page to your local
hard drive. Locate the file on your local hard drive by clicking the Browse button. Select the file and click the Upload button to start upgrading
the firmware.
Current Firmware Version: Displays the detected firmware version.
Current Product Name: Displays the camera model name.
DCS-2332L
File Path: Locate the file (upgraded firmware) on your hard drive
by clicking Browse.
Upload: Uploads the new firmware to your camera.
D-Link DCS-2332L User Manual
77
Section 4: Configuration
Status
Device Info
This page displays detailed information about your device and network connection.
DCS-2332L
DCS-2332L
D-Link DCS-2332L User Manual
78
Section 4: Configuration
Logs
This page displays the log information of your camera. You may download the information by clicking Download. You may also click Clear to
delete the saved log information.
DCS-2332L
D-Link DCS-2332L User Manual
79
Section 4: Configuration
Help
This page provides helpful information regarding camera operation.
DCS-2332L
D-Link DCS-2332L User Manual
80
Appendix A: Technical Specifications
Technical Specifications
Camera
Network
Camera Hardware
Profile
ƒƒ 1/4” Megapixel progressive CMOS sensor
ƒƒ 5 meter IR illumination distance
ƒƒ Minimum illumination: 0 lux with IR LED on
ƒƒ Built-in Infrared-Cut Removable (ICR) Filter module
ƒƒ Built-in PIR sensor (5 meter)
ƒƒ Built-in microphone and speaker
ƒƒ 10x digital zoom
ƒƒ Focal length: 3.45 mm
ƒƒ Aperture: F2.0
ƒƒ Angle of view:
ƒƒ (H) 57.8°
ƒƒ (V) 37.8°
ƒƒ (D) 66°
Image Features
ƒƒ Configurable image size, quality, frame rate, and bit rate
ƒƒ Time stamp and text overlays
ƒƒ Configurable motion detection windows
ƒƒ Configurable privacy mask zones
ƒƒ Configurable shutter speed, brightness, saturation, contrast,
and sharpness
Video Compression
ƒƒ Simultaneous H.264/MPEG-4/MJPEG format compression
ƒƒ H.264/MPEG-4 multicast streaming
ƒƒ JPEG for still images
Video Resolution
16:9 - 1280 x 800, 1280 x 720, 800 x 450, 640 x 360, 480 x 270, 320 4:3 - 1024 x 768, 800 x 600, 640 x 480, 480 x 360, 320 x 240, 176 x
x 176, 176 x 144
144
Audio Support
G.726, G.711
External Device
Interface
ƒƒ 10/100 BASE-TX Fast Ethernet port
ƒƒ IEEE 802.11n 2.4GHz single band wireless
ƒƒ microSD/SDHC card slot
Network Protocols
IEEE 802.11n 2.4GHz single band wireless
IPv6
IPv4
TCP/IP
UDP
ICMP
DHCP client
NTP client (D-Link)
DNS client
DDNS client (D-Link)
SMTP client
FTP client
HTTP / HTTPS
Samba Client
PPPoE
UPnP port forwarding
RTP / RTSP/ RTCP
IP filtering
QoS
CoS
Multicast
IGMP
ONVIF compliant
Security
ƒƒ Administrator and user group protection
ƒƒ Password authentication
ƒƒ HTTP and RTSP digest encryption
D-Link DCS-2332L User Manual
81
Appendix A: Technical Specifications
System
System
Management Requirements for
Web Interface
General
ƒƒ Operating System: Microsoft Windows 7/Vista/XP/2000
ƒƒ Browser: Internet Explorer, Firefox, Chrome, Safari
Event Management
ƒƒ Motion detection
ƒƒ Event notification and uploading of snapshots/video clips via
e-mail or FTP
ƒƒ Supports multiple SMTP and FTP servers
ƒƒ Multiple event notifications
ƒƒ Multiple recording methods for easy backup
Remote
Management
ƒƒ Take snapshots/video clips and save to local hard drive or NAS
via web browser
ƒƒ Configuration interface accessible via web browser
Mobile Support
Windows 7/Vista/XP system, Pocket PC, or mobile phone
mydlink mobile app for iOS and Android mobile devices
D-ViewCam™ System ƒƒ Operating System: Microsoft Windows 7/Vista/XP
Requirements
ƒƒ Web Browser: Internet Explorer 7 or higher
ƒƒ Protocol: Standard TCP/IP
D-ViewCam™
Software Functions
ƒƒ Remote management/control of up to 32 cameras
ƒƒ Viewing of up to 32 cameras on one screen
ƒƒ Supports all management functions provided in web interface
ƒƒ Scheduled motion triggered, or manual recording options
Weight
255 g
External Power
Adaptor
Input: 100 to 240 V AC, 50/60 Hz
Output: 5 V DC, 1.2 A
Power Consumption 5.5 Watts
Temperature
Operating: -25 to 45 °C (-13 to 113 °F)
Storage: -20 to 70 °C (-4 to 158 °F)
Humidity
Operating: 20% to 80% non-condensing
Storage: 5% to 95% non-condensing
Certifications
CE
CE LVD
FCC
C-Tick
IP65
IC
D-Link DCS-2332L User Manual
82
Appendix B: Safety Statements
Safety Statements
CE Mark Warning:
This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take
adequate measures.
FCC Statement:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
D-Link DCS-2332L User Manual
83
Appendix B: Safety Statements
IMPORTANT NOTICE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.
The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory
to match the intended destination. The firmware setting is not accessible by the end user.
For detailed warranty information applicable to products purchased outside the United States, please contact the corresponding local D-Link
office.
Industry Canada Notice:
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator & your body.
D-Link DCS-2332L User Manual
84
Appendix C: Contacting Technical Support
Contacting Technical Support
U.S. and Canadian customers can contact D-Link technical support through our web site or by phone.
Before you contact technical support, please have the following ready:
• Model number of the product (e.g., DCS-2332L)
• Hardware Revision (located on the label on the bottom of the Network Camera (e.g., rev A1))
• Serial Number (s/n number located on the label on the bottom of the Network Camera).
You can find software updates and user documentation on the D-Link website as well as frequently asked questions and
answers to technical issues.
For customers within the United States:
Phone Support:
(877) 453-5465
Internet Support:
http://support.dlink.com
D-Link DCS-2332L User Manual
For customers within Canada:
Phone Support:
(800) 361-5265
Internet Support:
http://support.dlink.ca
85
Appendix D: Warranty
Warranty
Subject to the terms and conditions set forth herein, D-Link Systems, Inc. (“D-Link”) provides this Limited Warranty:
• Only to the person or entity that originally purchased the product from D-Link or its authorized reseller or distributor, and
• Only for products purchased and delivered within the fifty states of the United States, the District of Columbia, U.S. Possessions
or Protectorates, U.S. Military Installations, or addresses with an APO or FPO.
Limited Warranty:
D-Link warrants that the hardware portion of the D-Link product described below (“Hardware”) will be free from material defects in workmanship
and materials under normal use from the date of original retail purchase of the product, for the period set forth below (“Warranty Period”), except
as otherwise stated herein.
• Hardware (excluding power supplies and fans): One (1) year
• Power supplies and fans: One (1) year
• Spare parts and spare kits: Ninety (90) days
The customer’s sole and exclusive remedy and the entire liability of D-Link and its suppliers under this Limited Warranty will be, at
D-Link’s option, to repair or replace the defective Hardware during the Warranty Period at no charge to the original owner or to refund the actual
purchase price paid. Any repair or replacement will be rendered by D-Link at an Authorized D-Link Service Office. The replacement hardware
need not be new or have an identical make, model or part. D-Link may, at its option, replace the defective Hardware or any part thereof with any
reconditioned product that D-Link reasonably determines is substantially equivalent (or superior) in all material respects to the defective Hardware.
Repaired or replacement hardware will be warranted for the remainder of the original Warranty Period or ninety (90) days, whichever is longer,
and is subject to the same limitations and exclusions. If a material defect is incapable of correction, or if D-Link determines that it is not practical
to repair or replace the defective Hardware, the actual price paid by the original purchaser for the defective Hardware will be refunded by D-Link
upon return to D-Link of the defective Hardware. All Hardware or part thereof that is replaced by D-Link, or for which the purchase price is refunded,
shall become the property of D-Link upon replacement or refund.
D-Link DCS-2332L User Manual
86
Appendix D: Warranty
Limited Software Warranty:
D-Link warrants that the software portion of the product (“Software”) will substantially conform to D-Link’s then current functional specifications
for the Software, as set forth in the applicable documentation, from the date of original retail purchase of the Software for a period of ninety (90)
days (“Software Warranty Period”), provided that the Software is properly installed on approved hardware and operated as contemplated in its
documentation. D-Link further warrants that, during the Software Warranty Period, the magnetic media on which D-Link delivers the Software will
be free of physical defects. The customer’s sole and exclusive remedy and the entire liability of D-Link and its suppliers under this Limited Warranty
will be, at D-Link’s option, to replace the non-conforming Software (or defective media) with software that substantially conforms to D-Link’s
functional specifications for the Software or to refund the portion of the actual purchase price paid that is attributable to the Software. Except as
otherwise agreed by DLink in writing, the replacement Software is provided only to the original licensee, and is subject to the terms and conditions
of the license granted by D-Link for the Software. Replacement Software will be warranted for the remainder of the original Warranty Period and is
subject to the same limitations and exclusions. If a material non-conformance is incapable of correction, or if D-Link determines in its sole discretion
that it is not practical to replace the non-conforming Software, the price paid by the original licensee for the non-conforming Software will be
refunded by D-Link; provided that the non-conforming Software (and all copies thereof ) is first returned to D-Link. The license granted respecting
any Software for which a refund is given automatically terminates.
Non-Applicability of Warranty:
The Limited Warranty provided hereunder for Hardware and Software portions of D-Link’s products will not be applied to and does not cover any
refurbished product and any product purchased through the inventory clearance or liquidation sale or other sales in which D-Link, the sellers, or
the liquidators expressly disclaim their warranty obligation pertaining to the product and in that case, the product is being sold “As-Is” without any
warranty whatsoever including, without limitation, the Limited Warranty as described herein, notwithstanding anything stated herein to the contrary.
Submitting A Claim (USA):
The customer shall return the product to the original purchase point based on its return policy. In case the return policy period has expired and
the product is within warranty, the customer shall submit a claim to D-Link as outlined below:
• The customer must submit with the product as part of the claim a written description of the Hardware defect or Software
nonconformance in sufficient detail to allow DLink to confirm the same, along with proof of purchase of the product (such as a
copy of the dated purchase invoice for the product) if the product is not registered.
• The customer must obtain a Case ID Number from D-Link Technical Support at 1-877-453-5465, who will attempt to assist the
customer in resolving any suspected defects with the product. If the product is considered defective, the customer must obtain a
Return Material Authorization (“RMA”) number by completing the RMA form and entering the assigned Case ID Number at https://
rma.dlink.com/.
D-Link DCS-2332L User Manual
87
Appendix D: Warranty
• After an RMA number is issued, the defective product must be packaged securely in the original or other suitable shipping package
to ensure that it will not be damaged in transit, and the RMA number must be prominently marked on the outside of the package.
Do not include any manuals or accessories in the shipping package. DLink will only replace the defective portion of the product
and will not ship back any accessories.
• The customer is responsible for all in-bound shipping charges to D-Link. No Cash on Delivery (“COD”) is allowed. Products sent COD
will either be rejected by D-Link or become the property of D-Link. Products shall be fully insured by the customer and shipped
to D-Link Systems, Inc., 17595 Mt. Herrmann, Fountain Valley, CA 92708. D-Link will not be held responsible for any packages that
are lost in transit to D-Link. The repaired or replaced packages will be shipped to the customer via UPS Ground or any common
carrier selected by D-Link. Return shipping charges shall be prepaid by D-Link if you use an address in the United States, otherwise
we will ship the product to you freight collect. Expedited shipping is available upon request and provided shipping charges are
prepaid by the customer. D-Link may reject or return any product that is not packaged and shipped in strict compliance with the
foregoing requirements, or for which an RMA number is not visible from the outside of the package. The product owner agrees to
pay D-Link’s reasonable handling and return shipping charges for any product that is not packaged and shipped in accordance
with the foregoing requirements, or that is determined by D-Link not to be defective or non-conforming.
Submitting A Claim (Canada):
The customer shall return the product to the original purchase point based on its return policy. In case the return policy period has expired and the
product is within warranty, the customer shall submit a claim to D-Link as outlined below:
• Customers need to provide their receipt (proof of purchase) even if the product is registered. Without a receipt, no warranty service will
be done. The registration is not considered a proof of purchase.
• The customer must submit with the product as part of the claim a written description of the Hardware defect or Software nonconformance
in sufficient detail to allow D-Link to confirm the same, along with proof of purchase of the product (such as a copy of the dated purchase
invoice for the product) if the product is not registered.
• The customer must obtain a Case ID Number from D-Link Technical Support at 1-800-361-5265, who will attempt to assist the customer
in resolving any suspected defects with the product. If the product is considered defective, the customer must obtain a Return Material
Authorization (“RMA”) number by completing the RMA form and entering the assigned Case ID Number at https://rma.dlink.ca/.
• After an RMA number is issued, the defective product must be packaged securely in the original or other suitable shipping package to
ensure that it will not be damaged in transit, and the RMA number must be prominently marked on the outside of the package. Do not
include any manuals or accessories in the shipping package. D-Link will only replace the defective portion of the product and will not ship
back any accessories.
D-Link DCS-2332L User Manual
88
Appendix D: Warranty
• The customer is responsible for all in-bound shipping charges to D-Link. No Cash on Delivery (“COD”) is allowed. Products sent COD will
be rejected by D-Link. Products shall be fully insured by the customer and shipped to D-Link Networks, Inc., 2525 Meadowvale Boulevard
Mississauga, Ontario, L5N 5S2 Canada. D-Link will not be held responsible for any packages that are lost in transit to D-Link. The repaired
or replaced packages will be shipped to the customer via Purolator Canada or any common carrier selected by D-Link. Return shipping
charges shall be prepaid by D-Link if you use an address in Canada, otherwise we will ship the product to you freight collect. Expedited
shipping is available upon request and provided shipping charges are prepaid by the customer. D-Link may reject or return any product
that is not packaged and shipped in strict compliance with the foregoing requirements, or for which an RMA number is not visible from
the outside of the package. The product owner agrees to pay D-Link’s reasonable handling and return shipping charges for any product
that is not packaged and shipped in accordance with the foregoing requirements, or that is determined by D-Link not to be defective or
non-conforming.
• RMA phone number: 1-800-361-5265 Hours of Operation: Monday-Friday, 9:00AM – 9:00PM EST
What Is Not Covered:
The Limited Warranty provided herein by D-Link does not cover:
Products that, in D-Link’s judgment, have been subjected to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty installation,
lack of reasonable care, repair or service in any way that is not contemplated in the documentation for the product, or if the model or serial number
has been altered, tampered with, defaced or removed; Initial installation, installation and removal of the product for repair, and shipping costs;
Operational adjustments covered in the operating manual for the product, and normal maintenance; Damage that occurs in shipment, due to act
of God, failures due to power surge, and cosmetic damage; Any hardware, software, firmware or other products or services provided by anyone
other than D-Link; and Products that have been purchased from inventory clearance or liquidation sales or other sales in which D-Link, the sellers,
or the liquidators expressly disclaim their warranty obligation pertaining to the product.
While necessary maintenance or repairs on your Product can be performed by any company, we recommend that you use only an Authorized D-Link
Service Office. Improper or incorrectly performed maintenance or repair voids this Limited Warranty.
Disclaimer of Other Warranties:
EXCEPT FOR THE LIMITED WARRANTY SPECIFIED HEREIN, THE PRODUCT IS PROVIDED “AS-IS” WITHOUT ANY WARRANTY OF ANY KIND WHATSOEVER
INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.
IF ANY IMPLIED WARRANTY CANNOT BE DISCLAIMED IN ANY TERRITORY WHERE A PRODUCT IS SOLD, THE DURATION OF SUCH IMPLIED WARRANTY
SHALL BE LIMITED TO THE DURATION OF THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE. EXCEPT AS EXPRESSLY COVERED UNDER THE
LIMITED WARRANTY PROVIDED HEREIN, THE ENTIRE RISK AS TO THE QUALITY, SELECTION AND PERFORMANCE OF THE PRODUCT IS WITH THE
PURCHASER OF THE PRODUCT.
D-Link DCS-2332L User Manual
89
Appendix D: Warranty
Limitation of Liability:
TO THE MAXIMUM EXTENT PERMITTED BY LAW, D-LINK IS NOT LIABLE UNDER ANY CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHER LEGAL
OR EQUITABLE THEORY FOR ANY LOSS OF USE OF THE PRODUCT, INCONVENIENCE OR DAMAGES OF ANY CHARACTER, WHETHER DIRECT, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL (INCLUDING, BUT NOT LIMITED TO, DAMAGES FOR LOSS OF GOODWILL, LOSS OF REVENUE OR PROFIT, WORK
STOPPAGE, COMPUTER FAILURE OR MALFUNCTION, FAILURE OF OTHER EQUIPMENT OR COMPUTER PROGRAMS TO WHICH D-LINK’S PRODUCT
IS CONNECTED WITH, LOSS OF INFORMATION OR DATA CONTAINED IN, STORED ON, OR INTEGRATED WITH ANY PRODUCT RETURNED TO D-LINK
FOR WARRANTY SERVICE) RESULTING FROM THE USE OF THE PRODUCT, RELATING TO WARRANTY SERVICE, OR ARISING OUT OF ANY BREACH OF
THIS LIMITED WARRANTY, EVEN IF D-LINK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE SOLE REMEDY FOR A BREACH OF
THE FOREGOING LIMITED WARRANTY IS REPAIR, REPLACEMENT OR REFUND OF THE DEFECTIVE OR NONCONFORMING PRODUCT. THE MAXIMUM
LIABILITY OF D-LINK UNDER THIS WARRANTY IS LIMITED TO THE PURCHASE PRICE OF THE PRODUCT COVERED BY THE WARRANTY. THE FOREGOING
EXPRESS WRITTEN WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ANY OTHER WARRANTIES OR REMEDIES, EXPRESS, IMPLIED
OR STATUTORY.
Governing Law:
This Limited Warranty shall be governed by the laws of the State of California. Some states do not allow exclusion or limitation of incidental or
consequential damages, or limitations on how long an implied warranty lasts, so the foregoing limitations and exclusions may not apply. This
Limited Warranty provides specific legal rights and you may also have other rights which vary from state to state.
Trademarks:
D-Link is a registered trademark of D-Link Corporation/D-Link Systems, Inc. Other trademarks or registered trademarks are the property of their
respective owners.
Copyright Statement:
No part of this publication or documentation accompanying this product may be reproduced in any form or by any means or used to make any
derivative such as translation, transformation, or adaptation without permission from D-Link Corporation/D-Link Systems, Inc., as stipulated by the
United States Copyright Act of 1976 and any amendments thereto. Contents are subject to change without prior notice.
Copyright ©2012 by D-Link Corporation/D-Link Systems, Inc. All rights reserved.
CE Mark Warning:
This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take
adequate measures.
D-Link DCS-2332L User Manual
90
Appendix D: Warranty
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one of the following measures:
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and receiver.
-
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to
operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory
to match the intended destination. The firmware setting is not accessible by the end user.
Industry Canada Statement
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
D-Link DCS-2332L User Manual
91
Appendix D: Warranty
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator & your body.
This device has been designed to operate with an antenna having a maximum gain of [2] dB. Antenna having a higher gain is strictly prohibited
per regulations of Industry Canada. The required antenna impedance is 50 ohms.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for
the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that
the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
This radio transmitter (IC: 4216A-AP1360C1 / Model: DAP-1360LC1) has been approved by Industry Canada to operate with the antenna types listed
below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this
list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Ce dispositif est conforme à la norme CNR-210 d’Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet
aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu,
y compris un brouillage susceptible de provoquer un fonctionnement indésirable.
NOTE IMPORTANTE:
Déclaration d’exposition aux radiations:
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit
être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.
Ce dispositif a été conçu pour fonctionner avec une antenne ayant un gain maximal de dB [2]. Une antenne à gain plus élevé est strictement interdite
par les règlements d’Industrie Canada. L’impédance d’antenne requise est de 50 ohms.
Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peutfonctionner avec une antenne d’un type et d’un gain maximal
(ou inférieur) approuvé pourl’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectriqueà l’intention des autres
utilisateurs, il faut choisir le type d’antenne et son gain de sorte que lapuissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité
nécessaire àl’établissement d’une communication satisfaisante.
D-Link DCS-2332L User Manual
92
Appendix D: Warranty
Le présent émetteur radio (IC: 4216A-AP1360C1 / Model: DAP-1360LC1) a été approuvé par Industrie Canada pour fonctionner avec les types
d’antenne énumérés ci-dessous et ayant un gain admissible maximal et l’impédance requise pour chaque type d’antenne. Les types d’antenne non
inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l’exploitation de l’émetteur.
Antenna information: dipole / 2dBi (Brand:D-Link / Manufacturer :WHA YU)
D-Link DCS-2332L User Manual
93
Appendix E: Registration
Registration
Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights.
Version 1.1
February 22, 2013
D-Link DCS-2332L User Manual
94