advertisement
Table of Contents
- - - - - - - - - - - - - - - - - - - - - - - 2
Introduction- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2
Overview - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2
Display - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3
Insert batteries - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4
Switching ON/OFF - - - - - - - - - - - - - - - - - - - - - - - - - 4
Clear - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4
Message Codes - - - - - - - - - - - - - - - - - - - - - - - - - - - 4
Adjusting measuring reference / tripod - - - - - - - - - - - 4
Multifunctional endpiece- - - - - - - - - - - - - - - - - - - - - - 5
Distance unit setting - - - - - - - - - - - - - - - - - - - - - - - - 5
Tilt unit setting- - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5
Timer (automatic release) - - - - - - - - - - - - - - - - - - - - 5
Beep ON/OFF- - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6
Illumination ON/OFF - - - - - - - - - - - - - - - - - - - - - - - - 6
- - - - - - - - - - - - - - - - - - - 7
Measuring single distance - - - - - - - - - - - - - - - - - - - - 7
Permament / Minimum-Maximum measuring - - - - - - - 7
Add / Subtract - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7
Area- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8
Volume- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 9
Triangular area - - - - - - - - - - - - - - - - - - - - - - - - - - - 10
Pythagoras (2-point) - - - - - - - - - - - - - - - - - - - - - - - 11
Pythagoras (3-point) - - - - - - - - - - - - - - - - - - - - - - - 11
Pythagoras (partial height) - - - - - - - - - - - - - - - - - - - 12
Stake out - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 13
Smart Horizontal Mode - - - - - - - - - - - - - - - - - - - - - 13
Height tracking - - - - - - - - - - - - - - - - - - - - - - - - - - - 14
Leveling - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 14
Memory (20 last displays) - - - - - - - - - - - - - - - - - - - 15
Dewalt DW03101
Delete Memory - - - - - - - - - - - - - - - - - - - - - - - - - - -15
- - - - - - - - - - - - - - - - - - - - - - - - - - - - -16
Calibration of tilt sensor (Tilt Calibration) - - - - - - - - -16
- - - - - - - - - - - - - - - - - - - - - - - - -17
- - - - - - - - - - - - - - - - - - - - - - - -18
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -18
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -18
- - - - - - - - - - - - - - - - - - - - -18
Areas of responsibility - - - - - - - - - - - - - - - - - - - - - -18
Permitted use - - - - - - - - - - - - - - - - - - - - - - - - - - - -19
Prohibited use - - - - - - - - - - - - - - - - - - - - - - - - - - - -19
Hazards in use - - - - - - - - - - - - - - - - - - - - - - - - - - -19
Limits of use - - - - - - - - - - - - - - - - - - - - - - - - - - - - -19
Disposal - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -19
Electromagnetic Compatibility (EMC)- - - - - - - - - - - -19
FCC statement (applicable in U.S.) - - - - - - - - - - - - -20
Laser classification- - - - - - - - - - - - - - - - - - - - - - - - -20
Labelling - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -20
EN
1
EN Instrument Set-up
Introduction
The safety instructions and the user manual should be read through carefully before the product is used for the first time.
The person responsible for the product must ensure that all users understand these directions and adhere to them.
The symbols used have the following meanings:
WARNING
Indicates a potentially hazardous situation or an unintended use which, if not avoided, will result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation or an unintended use which, if not avoided, may result in minor injury and/or appreciable material, financial and environmental damage.
i
Important paragraphs which must be adhered to in practice as they enable the product to be used in a technically correct and efficient manner.
Overview
Display
On / Measure
Units /
Memory
Pythagoras /
Stake out
Add
Smart
Horizontal
Mode /
Height
Tracking /
Inclination
DW03101
Timer
Clear /
Off
Area /
Volume /
Triangular area
Subtract
Measuring reference
2 Dewalt DW03101
Instrument Set-up
Display
Area /
Volume
Stake out
Measuring reference
Circumference
Angle
Wall area
Indirect height
Addition /
Subtraction
2nd result
Battery
Timer
Memory
Pythagoras
Horizontal measurement
Min/Max
Measuring
Units
Main line
Insert batteries
i
To ensure a reliable use, do not use zinc-carbon batteries.
Change batteries when battery symbol is flashing.
EN
Dewalt DW03101 3
EN Operations
Switching ON/OFF
2 sec
Device is turned OFF.
Clear
i
Press ON button 2 sec to start continuous laser mode. If no key is pressed for 180 sec, the device switches off automatically.
1x
Undo last action.
2x
Leave actual function, go to default operation mode.
Message Codes
If the info icon appears with a number, observe the instructions in section "Message
Codes".
Example:
Adjusting measuring reference / tripod
1 2
Distance is measured from the front of the device.
Distance is measured from the tripod thread permanently.
3
Distance is measured from the rear of the device (standard setting).
4 Dewalt DW03101
Operations
Multifunctional endpiece
i
The orientation of the endpiece is automatically detected and the zero point is accordingly adjusted.
Distance unit setting
2 sec
Switch between the following units:
0.000 m
0.0000 m
0.00 m
0.00 ft
0'00" 1/32
0.00 in
0 in 1/32
Timer (automatic release)
Tilt unit setting
2 sec simultaneously
1 s
2
Switch between the following units:
180 °
0.0 %
Adjust delay of automatic release
(max. 60 sec, standard setting
5 sec) i
Once the key is released with the laser activated, the remaining seconds until the measurement are displayed in a countdown. The delayed release is recommended for precise aiming e.g. at long distances. It avoids shaking of the device when pressing the measurement key.
Dewalt DW03101
EN
5
EN Operations
Beep ON/OFF
2 sec simultaneously
Illumination ON/OFF
2 sec simultaneously
6 Dewalt DW03101
Measuring Functions
Measuring single distance
EN
1 2 3
8.532 m i
Target surfaces: Measuring errors can occur when measuring to colourless liquids, glass, styrofoam or semi-permeable surfaces or when aiming at high gloss surfaces. Against dark surfaces the measuring time increases.
Aim active laser at target.
Permament / Minimum-Maximum measuring
min.
max.
1 2
2 sec
Used to measure room diagonals (maximum values) or horizontal distance (minimum values)
The minimum and maximum distance measured is displayed
(min, max.). The last value measured is displayed in the main line.
3
8.532 m
Stops permanent / minimummaximum measuring.
Add / Subtract
1
7.332 m
2
The next measurement is added to the previous one.
The next measurement is subtracted from the previous one.
3 i
The result is shown in the main line and the measured value above. This process can be repeated as required.
The same process can be used for adding or subtracting areas or volumes.
Dewalt DW03101 7
EN Measuring Functions
Area
1x
1 2
Aim laser at first target point.
3
6
2 sec
19.823 m
24.352 m
2
Circumference
Area
4
Aim laser at second target point.
5
24.352 m
2 i
The result is shown in the main line and the measured value above.
8 Dewalt DW03101
Measuring Functions
Volume
2x
1 2
Aim laser at first target point.
3 4
Aim laser at second target point.
5
7
78.694 m
3 i
The result is shown in the main line and the measured value above.
8
2 sec
80.208 m
208.703 m
2
78.694 m
3
Circumference
Wall areas
Volume
6
Aim laser at third target point.
EN
Dewalt DW03101 9
EN Measuring Functions
Triangular area
3x
1 2
Aim laser at first target point.
3 4
Aim laser at second target point.
5
7
24.352 m
2
8
2 sec
40.8 °
33.852 m
24.352 m
2
Angle included by the first two measurements
Circumference
Triangular area
6
Aim laser at third target point.
10 Dewalt DW03101
Measuring Functions
Pythagoras (2-point)
1x
1 2
Aim laser at upper point.
3 4
Aim laser rectangular at lower point.
5
8.294 m
7
Pythagoras (3-point)
2x
1 2
Aim laser at upper point.
3 4
Aim laser at rectangular point.
5 i
The result is shown in the main line and the measured distance above.
Pressing the measuring key for
2 sec in the function activates automatically Minimum or Maximum measurement.
8.294 m
Dewalt DW03101
6 i
The result is shown in the main line and the measured distance above.
Pressing the measuring key for 2 sec in the function activates automatically
Minimum or Maximum measurement.
Aim laser at lower point.
EN
11
EN Measuring Functions
Pythagoras (partial height)
3x
1 2 3
Aim laser at upper point.
7
2.602 m
4
Aim laser at 2nd point.
5 i
The result is shown in the main line and the measured distance above.
Pressing the measuring key for 2 sec in the function activates automatically Minimum or Maximum measurement.
6
Aim laser at rectangular point.
12 Dewalt DW03101
4
Measuring Functions
Stake out
1
2
3
Move device slowly along the stake-out line.
The distance to the next stake out point is displayed.
1
4x
2 3
1.000 m
Adjust value.
0.625 m
Approve value and start measurement.
0.625 m
0.240 m
0.240 m is missing up to next 0.625 m distance.
i
When approaching a stake out point to less than 0.1 m the instrument starts to beep.
The function can be stopped by pressing the CLEAR/OFF button.
EN
Smart Horizontal Mode
1x
1 2
Aim laser at target.
3
24.3 °
0.032 m
4.827 m
α
y z z
(up to 360° and a transverse tilt of ±10°)
Dewalt DW03101 i
Press key again to switch off horizontal measurement.
13
EN Measuring Functions
Height tracking
i
This function displays continously the tracking height if the device is turned on a tripod. No 2nd distance measuring is needed as only the angle is automatically measured.
1
2x
2 3 4 h3 h2 h1
14
5
6.932 m
30.2 °
9.827 m x
= Tracking angle y = Tracking height if device is turned on tripod i
Leveling
This function displays continously the inclination of the device. From an inclination of ±5° the device starts beeping frequently. The more it gets to 0° the faster it beeps. If an inclination of ±0.3° is reached the device beeps continuously.
1
3x
2 x
Aim laser at lower point.
h3 h2 h1 i
The tracked height "y" is in
90° to the 1st aimed point
"x".
6
Aim laser at upper points and angle/ height tracking starts automatically.
Stops Height tracking and displays last measurement.
Place device on object to be levelled.
Dewalt DW03101
8.7 °
The inclination is displayed
(Range
±180°).
Measuring Functions
Memory (20 last displays)
1
20 20 last displays are displayed.
8.294 m
2
Delete Memory
20
Navigates trough
8.294 m 20 last displays.
2 sec
The value from the main line can be used for further calculations.
3
2 sec simultaneously
Memory is completely deleted.
EN
Dewalt DW03101 15
EN Calibration
Calibration of tilt sensor (Tilt Calibration)
1
2 sec simultaneously
2
Place device on absolutely flat surface.
3
4
180°
5 6
7
Turn the device horizontally by 180° and place it again on absolutely flat surface.
8
180°
Turn the device horizontally by 180° and place it again on absolutely flat surface.
9
Turn the device and place it again on absolutely flat surface.
i
After 2 sec the device goes back to the normal mode.
16 Dewalt DW03101
Technical Data
Distance measurement
Typical Measuring Tolerance* ± 1.0 mm / 0.04 in ***
Maximum Measuring Tolerance**
± 2.0 mm / 0.08 in ***
Range of target plate
Typical Range*
Range at unfavourable condition ****
100 m / 330 ft
80 m / 262 ft
60 m / 197 ft
Smallest unit displayed
Ø laser point at distances
0.1 mm / 1/32 in
6 /30 / 60 mm
(10 / 50 / 100 m)
Tilt measurement
Measuring tolerance to laser beam*****
Measuring tolerance to housing*****
Range
± 0.2°
± 0.2°
360°
General
Laser class
Laser type
Beam divergence
Impulse duration
Protection class
2
635 nm, < 1 mW
0.16 x 0.6 mrad
0.2 x 10 -9 s - 0.8 x 10 -9 s
IP65 (dust- and splash water protected)
Autom. laser switch off
Autom. power switch-off
Weight (with batteries)
Temperature range:
- Storage after 90 s after 180 s
Battery durability (2 x AAA) up to 5000 measurements
Dimension (H x D x W) 125.2 x 58 x 32.6 mm
4.9 x 2.3 x 1.3 in
154 g / 5.43 oz
- Operation
-25 to 70 °C
-13 to 158 °F
-10 to 50 °C
14 to 122 °F
* applies for 100 % target reflectivity (white painted wall), low background illumination, 25 ºC
** applies for 10 to 500 % target reflectivity, high background illumination, - 10 ºC to + 50 ºC
*** Tolerances apply from 0.05 m to 10 m with a confidence level of 95%. The maximum tolerance may deteriorate to 0.1 mm/m between 10 m to 30 m and to
0.2 mm/m for distances above 30 m
**** applies for 100 % target reflectivity, background illumination of approximately 30'000 lux
***** after user calibration. Additional angle related deviation of +/- 0.01° per degree up to +/-45° in each quadrant. Applies at room temperature. For the whole operating temperature range the maximum deviation increases by +/- 0.1°.
i
For accurate indirect results, the use of a tripod is recommended. For accurate tilt measurements a transverse tilt should be avoided.
Functions
Distance measuring
Min/Max measuring
Permanent measuring
Stake-out
Addition/Subtraction
Area
Volume
Pythagoras
Smart Horizontal Mode /
Indirect height
Height tracking
Levelling
Memory
Beep
Illuminated display
Multifunctional endpiece yes yes yes yes yes yes yes
2-point, 3-point, partial height yes yes yes
20 displays yes yes yes
EN
Dewalt DW03101 17
EN Message Codes
If the message Error does not disappear after switching on the device repeatedly, contact the dealer.
If the message InFo appears with a number, press the Clear button and observe the following instructions:
No.
Cause
156 Transverse tilt greater than 10°
Correction
Hold the instrument without any transverse tilt.
162 Calibration mistake Make sure, the device is placed on a absolutely horizontal and flat surface. Repeat the calibration procedure. If the mistake still occurs, contact your dealer.
204 Calculation error Perform measurement again.
Let device cool down.
252 Temperature too high
253 Temperature too low
Warm device up.
Change target surface
(e.g. white paper).
255 Received signal too weak, measuring time too long
256 Received signal too high
257 Too much background light
258 Measurement outside of measuring range
Change target surface
(e.g. white paper).
Shadow target area.
Correct range.
260 Laser beam interrupted
Repeat measurement.
Care
• Clean the device with a damp, soft cloth.
• Never immerse the device in water.
• Never use aggressive cleaning agents or solvents.
Warranty
Europe:
• 30 day no risk satisfaction guarantee
• One year free service
• One year full warranty
Detailed information are available on the internet at www.2helpU.com.
North America:
• Three year limited warranty
• One year free service
• 90 day money back guarantee
Detailed information are available on the internet at www.dewalt.com.
Safety Instructions
The person responsible for the instrument must ensure that all users understand these directions and adhere to them.
Areas of responsibility
Responsibilities of the manufacturer of the original equipment:
Europe:
DEWALT
D-65510 Idstein, Germany www.2helpU.com
www.dewalt.eu
North America:
DEWALT Industrial Tool Co.
Baltimore, MD21286, USA
For service call 1-800-4-DEWALT.
www.dewalt.com
The company above is responsible for supplying the product, including the User
Manual in a completely safe condition.
The company above is not responsible for third party accessories.
Responsibilities of the person in charge of the instrument:
• To understand the safety instructions on the product and the instructions in the
User Manual.
• To be familiar with local safety regulations relating to accident prevention.
• Always prevent access to the product by unauthorised personnel.
18 Dewalt DW03101
Safety Instructions
Permitted use
• Measuring distances
• Tilt measurement
Prohibited use
• Using the product without instruction
• Using outside the stated limits
• Deactivation of safety systems and removal of explanatory and hazard labels
• Opening of the equipment by using tools
(screwdrivers, etc.)
• Carrying out modification or conversion of the product
• Use of accessories from other manufacturers without express approval
• Deliberate dazzling of third parties; also in the dark
• Inadequate safeguards at the surveying site (e.g. when measuring on roads, construction sites, etc.)
• Deliberate or irresponsible behaviour on scaffolding, when using ladders, when measuring near machines which are running or near parts of machines or installations which are unprotected
• Aiming directly in the sun
Hazards in use
WARNING
Watch out for erroneous measurements if the instrument is defective or if it has been dropped or has been misused or modified.
Carry out periodic test measurements.
Particularly after the instrument has been subject to abnormal use, and before, during and after important measurements.
CAUTION
Never attempt to repair the product yourself. In case of damage, contact a local dealer.
WARNING
Changes or modifications not expressly approved could void the user’s authority to operate the equipment.
Limits of use
i
Refer to section "Technical data".
The device is designed for use in areas permanently habitable by humans. Do not use the product in explosion hazardous areas or in aggressive environments.
Disposal
CAUTION
Flat batteries must not be disposed of with household waste. Care for the environment and take them to the collection points provided in accordance with national or local regulations.
The product must not be disposed with household waste.
Dispose of the product appropriately in accordance with the national regulations in force in your country.
Adhere to the national and country specific regulations.
Product specific treatment and waste management can be downloaded from our homepage.
Electromagnetic Compatibility
(EMC)
WARNING
The device conforms to the most stringent requirements of the relevant standards and regulations.
Yet, the possibility of causing interference in other devices cannot be totally excluded.
EN
Dewalt DW03101 19
EN Safety Instructions
FCC statement (applicable in U.S.)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Laser classification
The device produces visible laser beams, which are emitted from the instrument:
It is a Class 2 laser product in accordance with:
• IEC60825-1 : 2007 „Radiation safety of laser products“
Laser Class 2 products:
Do not stare into the laser beam or direct it towards other people unnecessarily. Eye protection is normally afforded by aversion responses including the blink reflex.
WARNING
Looking directly into the beam with optical aids (e.g. binoculars, telescopes) can be hazardous.
CAUTION
Looking into the laser beam may be hazardous to the eyes.
Labelling
a a
Attach the laser sticker (a) of your country language.
20 Dewalt DW03101
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement