Electrolux EWM2000evo Service manual

SERVICE MANUAL
WASHING
WASHING-MACHINES
&
WASHER-DRYERS
 ELECTROLUX HOME PRODUCTS
ITALY S.p.A.
Spares Operations Italy
Corso Lino Zanussi, 30
I - 33080 PORCIA /PN
Fax +39 0434 394096
Edition: 2005-01-12 dmm
Publication no.
599 36 82-59
EN
with electronic control
EWM2000EVO
with sensors
“FULL SMD”
display board
Production ZP (Porcia-Italy)
SOI/DT 2005-01 dmm
2/67
599 36 82 59
INDICE
1
2
3
Purpose of this manual .............................................................................................................................. 6
PRECAUTIONS ......................................................................................................................................... 6
GENERAL SPECIFICATIONS................................................................................................................... 7
3.1
General specifications WM ................................................................................................................. 7
3.2
General specifications WD ................................................................................................................. 7
4 CONTROL PANEL..................................................................................................................................... 8
4.1
Control/display board.......................................................................................................................... 9
4.1.1
Version with display..................................................................................................................... 9
4.1.2
Version without display................................................................................................................ 9
5 WASHING PROGRAMMES .................................................................................................................... 10
5.1
Configuration of programmes ........................................................................................................... 10
5.2
Programme selector ........................................................................................................................ 10
5.3
Start/Pause ....................................................................................................................................... 10
5.4
Button functions ................................................................................................................................ 10
6 WASHING PROGRAMMES AND OPTIONS .......................................................................................... 11
6.1
Possible programmes ....................................................................................................................... 11
6.2
Options of the washing cycle ............................................................................................................ 12
6.3
Description of options ....................................................................................................................... 13
6.3.1
Night cycle ................................................................................................................................. 13
6.3.2
Rinse Hold ................................................................................................................................. 13
6.3.3
Prewash..................................................................................................................................... 13
6.3.4
Soak........................................................................................................................................... 13
6.3.5
Stains......................................................................................................................................... 13
6.3.6
Short (daily) ............................................................................................................................... 13
6.3.7
Very Short.................................................................................................................................. 13
6.3.8
Intensive .................................................................................................................................... 13
6.3.9
Economy / Energy label............................................................................................................. 14
6.3.10 Sensitive .................................................................................................................................... 14
6.3.11 Extra rinse ................................................................................................................................. 14
6.3.12 Bleach........................................................................................................................................ 14
6.3.13 “Half load” button ....................................................................................................................... 14
6.3.14 Easy-Iron ................................................................................................................................... 14
6.3.15 Reduced spin speed.................................................................................................................. 14
6.3.16 No spin....................................................................................................................................... 14
6.3.17 Modifying the spin speed........................................................................................................... 15
6.3.18 Time reduction (Quick) .............................................................................................................. 15
6.3.19 Temperature adjustment ........................................................................................................... 15
6.3.20 Delayed-start time ..................................................................................................................... 15
6.3.21 Exclude buzzer .......................................................................................................................... 15
6.3.22 Electronic drying (WASHER-DRYERS – certain models only) ................................................. 15
6.3.23 “Drying time” button ................................................................................................................... 15
6.3.24 Variation of rinses when options are selected........................................................................... 16
6.4
Display (certain models only)............................................................................................................ 16
6.5
LEDs ................................................................................................................................................. 17
7 WASHING PROGRAMMES .................................................................................................................... 18
7.1
Base programmes for Cotton / Linen: cold-30-40-60-90° (without options) ..................................... 18
7.2
Rinses of Cotton programmes .......................................................................................................... 19
7.3
Cotton / Linen programmes: 90 Eco, 40-60 “energy label” (without options)................................... 20
7.4
Rinses of Cotton / Linen programmes: 90 Eco, 40-60 “energy label” (without options)................... 21
7.4.1
For programmes with two rinses ............................................................................................... 21
7.4.2
For programmes with three rinses............................................................................................. 21
7.5
Synthetics programmes: cold – 30 – 40 – 50 – 60° (without options) .............................................. 22
7.6
Rinses of synthetics programmes .................................................................................................... 23
7.7
Programmes for delicate fabrics: cold – 30° - 40° (without options) ................................................ 24
7.8
Wool programmes: cold – 30° - 40°.................................................................................................. 25
7.9
Hand wash programmes: cold – 30° - 40°........................................................................................ 26
8 DRYING PROGRAMMES........................................................................................................................ 27
8.1
Drying programme for cotton ............................................................................................................ 27
8.2
Drying programme for synthetics...................................................................................................... 27
8.3
Drum movements at low speed and during spin .............................................................................. 28
8.3.1
D55 Delicate movement ............................................................................................................ 28
8.3.2
N55 Normal movement.............................................................................................................. 28
8.3.3
E55 Vigorous movement ........................................................................................................... 28
SOI/DT 2005-01 dmm
3/67
599 36 82 59
8.3.4
PWL_1 (wool) Delicate movement ............................................................................................ 28
8.3.5
PWL_4 (hand wash) Delicate movement .................................................................................. 28
8.3.6
Cotton/Linen, Synthetics – Intermediate Synthetics Prewash Spin .......................................... 29
8.3.7
Cotton/Linen, Intermediate Cotton/Linen Wash Spin ................................................................ 29
8.3.8
Cotton/Linen Final Spin ............................................................................................................. 29
8.3.9
Synthetics Final Spin ................................................................................................................. 29
8.3.10 Delicates Final Spin................................................................................................................... 30
8.3.11 Hand Wash and Wool Final Spin .............................................................................................. 30
8.3.12 Easy iron Impulse Cycle EI........................................................................................................ 30
8.3.13 Intermediate Spin for Cotton/Linen Super-rinse option ............................................................. 30
8.3.14 Movement during drying phase ................................................................................................. 30
8.4
Control of water level in tub .............................................................................................................. 31
9 TECHNICAL CHARACTERISTICS.......................................................................................................... 32
9.1
EWM2000EVO Electronic control.................................................................................................... 32
9.1.1
Functions of the circuit board .................................................................................................... 32
9.1.2
Memory in the control system ................................................................................................... 32
9.2
Analogic pressure switch (electronic) ............................................................................................... 34
9.3
Pressure switch ................................................................................................................................ 35
9.3.1
Pressure switch settings............................................................................................................ 35
9.4
Anti-flooding device .......................................................................................................................... 36
9.5
Power supply and programme selection .......................................................................................... 36
9.6
Door interlock.................................................................................................................................... 37
9.6.1
Voltmetric interlock with PTC..................................................................................................... 37
9.6.2
Instantaneous door interlock ..................................................................................................... 38
9.7
Detergent dispenser ......................................................................................................................... 39
9.8
Water fill system ............................................................................................................................... 39
9.9
Flow meter ........................................................................................................................................ 40
9.9.1
Operating principle of flow meter............................................................................................... 40
9.10
Drain pump.................................................................................................................................... 41
9.11
Drain pump.................................................................................................................................... 42
9.12
Aqua Control ................................................................................................................................. 42
9.13
Heating system ............................................................................................................................. 43
9.13.1 Heating element ........................................................................................................................ 43
9.13.2 Temperature sensor .................................................................................................................. 43
9.14
Turbidity sensor............................................................................................................................. 44
9.15
Motor ............................................................................................................................................. 45
9.16
Power supply to motor .................................................................................................................. 45
9.17
Anti-foam control system............................................................................................................... 45
9.18
“FUCS” (Fast Unbalance Control System).................................................................................... 46
10
DRYING CIRCUIT ................................................................................................................................ 48
10.1
Temperature control...................................................................................................................... 49
Calculating the drying time:...................................................................................................................... 49
11
DEMO Mode......................................................................................................................................... 50
11.1
Exiting demo mode ....................................................................................................................... 50
12
DIAGNOSTICS SYSTEM..................................................................................................................... 51
12.1
Access to diagnostics system ....................................................................................................... 51
12.2
Exiting diagnostics system ............................................................................................................ 51
12.3
Phases of the diagnostics test ...................................................................................................... 51
12.3.1 Display board diagnostics.......................................................................................................... 53
12.3.2 Programme selector .................................................................................................................. 54
13
ALARMS............................................................................................................................................... 55
13.1
Displaying the alarms to the user (for appliances with Display) ................................................... 55
13.1.1 Alarms displayed during normal operation ................................................................................ 55
13.2
Reading the alarm codes .............................................................................................................. 56
13.2.1 Displaying the alarm .................................................................................................................. 56
13.2.2 Examples of alarm displays....................................................................................................... 56
13.2.3 Operation of alarms during diagnostics..................................................................................... 57
13.3
Notes about some alarms ............................................................................................................. 57
13.4
Rapid reading of alarm codes ....................................................................................................... 57
13.5
Cancelling the last alarm with LEDs ............................................................................................. 57
13.6
Table of alarm codes..................................................................................................................... 58
14
Operating time counter......................................................................................................................... 61
14.1.1 Operating time reading .............................................................................................................. 61
14.1.2 Displaying the operating time .................................................................................................... 61
15
ACCESSING COMPONENTS ............................................................................................................. 62
SOI/DT 2005-01 dmm
4/67
599 36 82 59
15.1
Flow meter..................................................................................................................................... 62
15.2
Aqua Control ................................................................................................................................. 62
15.3
Turbidity sensor............................................................................................................................. 63
15.3.1 Installing the turbidity sensor ..................................................................................................... 63
16
BASIC CIRCUIT DIAGRAM WD .......................................................................................................... 64
16.1
Key for circuit diagram WD ........................................................................................................... 65
17
BASIC CIRCUIT DIAGRAM WM.......................................................................................................... 66
17.1
Key for circuit diagram WM ........................................................................................................... 67
SOI/DT 2005-01 dmm
5/67
599 36 82 59
1 Purpose of this manual
The purpose of this manual is to provide service engineers who are already familiar with the repair procedures
for traditional washing machines with information regarding appliances fitted with the EWM 2000EVO electronic
control system and produced in Porcia (Italy).
The electronic control system EWM 2000EVO consists of a main electronic board and one control/display
board, “Full SMD” version.
The following are described:
• General characteristics
• Control panel and washing programmes
• Technical characteristics
• Guide to the diagnostics
For detailed information concerning hydraulic circuit, structural characteristics of the appliances and
accessibility, please refer to Service Manual of washing machines and washer-dryers Series P6000/Nexus
(publication no. 599 35 23-17).
2 PRECAUTIONS
ƒ
ƒ
Electrical appliances must be serviced only by qualified Service Engineers.
Always remove the plug from the power socket before touching internal
components.
SOI/DT 2005-01 dmm
6/67
599 36 82 59
3 GENERAL SPECIFICATIONS
3.1
General specifications WM
Programme selector
Serial port
Power supply
Type of washing
Rinsing system
Motor
Spin speed
Anti-unbalancing system
Water fill
Detergent drawer
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
Control of water level in the tub
Door safety device
Power of heating element
Temperature control
Audible signalling system
Sensors
3.2
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
16-24 positions with incorporated main switch
DAAS-EAP communications protocol up to 38400 baud
220/240V
50/60 Hz
Jet-system
Jet-system
Collector, with tachometric generator
850 ÷ 1600 g/’
FUCS
1 solenoid valve with 1 inlet – 2 or 3 outlets
3 compartments: prewash/stains, wash, conditioners
4 compartments: prewash/stains, wash, conditioners, bleach
possibility of three-level pressure switch: 2 anti-boiling and
anti-flooding safety levels
electronic/analogic pressure switch
Traditional (with PTC)
Instantaneous
Up to 1950W
NTC sensor
Traditional, included on display board
Water level sensor
Turbidity sensor
General specifications WD
Programme selector
Serial port
Power supply
Type of washing
Rinsing system
Motor
Spin speed
Anti-unbalancing system
Water fill
Detergent drawer
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
Control of water level in the tub
Door safety device
Power of heating element
Power of drying heating element
Temperature control
Audible signalling system
Sensors
SOI/DT 2005-01 dmm
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
16-24 positions with incorporated main switch
DAAS-EAP communications protocol up to 38400 baud
220/240V
50/60 Hz
Jet-system
Jet-system
Collector, with tachometric generator
850 ÷ 1600 g/’
FUCS
1 solenoid valve with 1 inlet – 2 or 3 outlets
3 compartments: prewash/stains, wash, conditioners
4 compartments: prewash/stains, wash, conditioners, bleach
possibility of three-level pressure switch: 2 anti-boiling and
anti-flooding safety levels
electronic/analogic pressure switch
Traditional (with PTC)
Instantaneous
Up to 1950W
Up to 1840W (920 + 920)
Only for built-in models up to 1100W (550+550)
NTC sensor
Traditional, included on display board
Water level sensor
Turbidity sensor
7/67
599 36 82 59
4 CONTROL PANEL
The configuration of the control panel depends on the following:
ª Type of control/display board (with or without display)
ª Design of the control panel and position of the programme selector (right or left of the buttons)
ª Number and configuration of the buttons (max. 8)
ª ON/OFF switch: incorporated in the programme selector or with separated button.
Sigma
Version with left selector and incorporated ON/OFF button
Ellipse
Alpha
Version with left selector and button ON/OFF switch
Multipanel
Built-in
Version with right selector and incorporated ON/OFF switch
Sigma/ZK
Version with right selector and incorporated ON/OFF switch
Jewel
Version with left selector and incorporated ON/OFF button
SOI/DT 2005-01 dmm
8/67
599 36 82 59
4.1
4.1.1
Control/display board
Version with display
Ö 3 digits
Ö 28 LEDs
Ö 8 buttons
4.1.2
Version without display
Ö 21 LEDs
Ö 6 buttons
Ö 14 LEDs
Ö 6 buttons
SOI/DT 2005-01 dmm
9/67
599 36 82 59
5 WASHING PROGRAMMES
5.1
Configuration of programmes
The table below lists the parameters that can be used to define the washing programmes.
Type of fabric
Special programmes
Temperature
Spin
Options (Normal / Possible)
Programme phases
5.2
Cotton/linen, Synthetic fibres, Delicates, Wool, Hand wash, Mini
Soak, Rinses, Spin, Drain, Conditioner
Normal, Maximum: initial and maximum temperatures that can be
selected for a specific washing programme
Normal, Minimum, Maximum
Bleaches, Economy (Energy Label), Stains, Short, Very short,
Reduced spin, Night cycle, Half-load, Easy-Iron, Rinse Hold,
Extra Rinse, Pre-wash, Soak, Sensitive, Vigorous, No spin, Level
of Drying
Pre-wash, Wash, Rinses, Spin, End of cycle, Drying
Programme selector
The programme selector determines the type of washing cycle
(e.g. water level, drum movement, number of rinses) and the
washing temperature to be selected for each type of fabric.
The programme selector may be rotated in either direction
(clockwise or counter-clockwise).
The first position is used to cancel the current programme (and, if
the main ON/OFF switch is built into the programme selector, to
switch the appliance off).
5.3
Start/Pause
Start:
After selecting the programme and the desired options, press this button to start the cycle.
If the delayed-start option has been selected, the count-down will begin, and will be shown on the
display. The LED stops flashing and remains lit for the entire duration of the programme.
Pause: If the button is pressed again, the current programme is interrupted and the display (or the
corresponding LED) begins to flash. When in pause mode, the door can be opened, but only if the
machine is not performing the heating phase, the water level is not high, and the drum is
stationary.
During the pause, the following modifications can be made to the programme:
- the OPTIONS for the cycle can be modified before the start of the phase in which they are
activated
- the SPIN selection can be modified before the beginning of the final spin.
To re-start the programme, press START/PAUSE again.
5.4
Button functions
The washing programmes and the functions for each button vary according to the model, since
these are determined by the procedure for the configuration of the appliance.
SOI/DT 2005-01 dmm
10/67
599 36 82 59
6 WASHING PROGRAMMES AND OPTIONS
6.1
Possible programmes
The wash programmes can be configured to suit personal needs. The table below lists the standard
programmes.
Programme
90
90E
60
60E
Cotton
50
50/40E
40
30
Cold (¹)
60
60/50E
50
Synthetics
40
30
Cold (¹)
40
Delicate fabrics
30
Cold
40
Wool
30
Cold
40
Hand wash
30
Cold
Temperature (°C)
85
67
60
50 (*)(**)
50
44 (*)
42
30
20
60
42 (*)
50
40
30
20
40
30
20
40
35
20
40
35
20
No. of rinses
3
2
3
2
3
2
Soak
Rinses
Rinse for delicate fabrics
Fabric softener
Drain
Spin
Delicate spin
Short cycle
30/20
------------------30
Final spin (RPM)
450/650/850/1000/1200/
1300/1400/1600
3
3
Max. 900
3
450/700
3
Max. 1000
3
Max. 1000
---3
3
1
---------2
---Max. 1600
Max. 700
Max. 1600
---Max. 1600
Max. 700
Max. 1000
The data are indicative
(*) “energy label” programmes
(¹) in the washer-dryers this is a drying phase
(**)
Programme
COTTON 60 E
SOI/DT 2005-01 dmm
Group
Temperature (°C)
G19/20/22
45÷54
11/67
599 36 82 59
6.2 Options of the washing cycle
The selection of the options is to be carried out after switching on the appliance and setting the desired
programme with the selector and before pressing the start/pause button.
When the button is pressed, the corresponding LED lights; by pressing it again the LED switches off.
Possible options according the selected programme
SOI/DT 2005-01 dmm
Bleach
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
12/67
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
599 36 82 59
Drying
Extra rinse
X
X
X
X
Reduced spin
speed
Sensitive
X
X
X
X
X
X
X
X
X
X
X
Easy iron
Economy
X
X
X
X
X
X
X
X
X
X
X
Half-load
Short
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Rinse-hold
SOAK
RINSES
CONDITIONER
DRAIN
SPIN
RINSE HOLD
NIGHT CYCLE
PRE-WASH
SOAK
STAINS
INTENSIVE
DAILY
SHORT
ECONOMY
SENSITIVE
EXTRA RINSE
BLEACH
HALF LOAD
EASY IRON
REDUCED SPIN SPEED
NO SPIN
PRE-SELECTION
PRE-WASH
WASH
RINSES
SPIN
Daily
WOOL – HANDWASH
Stains
SILK
Soak
DELICATES
Pre-wash
MINI PROGRAMME
Night cycle
SYNTHETIC
FABRICS
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
No spin
Phases in
which
selection is
possible
Compatibility with OPTIONS
Compatibility with PROGRAMMES
COTTON
90°C
60°C
50°C
40°C
30°C
Cold
60°C
50°C
40°C
30°C
Cold
30°C
40°C
30°C
Cold
30°C
40°C
30°C
Cold
Rinse-hold
OPZIONI
6.3 Description of options
6.3.1
Night cycle
ª All the spin phases are eliminated. Three rinses are added to COTTON cycles and one rinse is added
to SYNTHETICS cycles.
ª The appliance is shut down with water in the drum before the final spin.
ª No buzzer (if appliance is configured with a buzzer).
ª To drain the water, select a drain or spin cycle.
6.3.2
Rinse Hold
ª The appliance is shut down with water in the drum before the final spin.
ª To drain the water, select a drain or spin cycle.
6.3.3
Prewash
ª A prewash phase is added at the beginning of the cycle. The water is heated to 30°C (or may be cold, if
selected).
ª In COTTON and SYNTHETICS cycles, a short spin (pulse spin) is performed before the wash phase.
ª This option is not available in WOOL and HAND WASH cycles.
6.3.4
Soak
ª A prewash phase is added (lasting 30’, with the same agitation as in the wool cycle) at the beginning of
the programme. The water is heated to 30°C (or may be cold, if selected).
ª In COTTON and SYNTHETICS cycles, a short spin (pulse spin) is performed before the wash phase.
ª When combined with the delayed start option, a soak time from 30 minutes to 10 hours can be selected.
ª This option is not available in WOOL and HAND WASH cycles.
6.3.5
Stains
ª The motor operates for an extra 5 minutes after the water is heated to 40°C.
ª Water is run through the prewash/stain remover compartment to withdraw the special stain removing
product.
ª This option is not available in DELICATE FABRICS, WOOL and HAND WASH cycles.
ª Agitation during washing changes from vigorous to normal.
6.3.6
Short (daily)
ª The structure of the wash phase in the COTTON - SYNTHETICS programmes is modified to obtain
good performance in a short time (optimized for small loads).
6.3.7
Very Short
ª The structure of the COTTON – SYNTHETICS – DELICATE FABRICS programmes is modified to
obtain very short time wash times (optimized for small, lightly soiled loads).
ª The number of rinses is reduced (one less rinse).
ª The water level in the other two rinses is increased.
6.3.8
Intensive
ª 10 minutes of normal movement are added to the wash phase in the cotton programme.
SOI/DT 2005-01 dmm
13/67
599 36 82 59
6.3.9
Economy / Energy label
ª The COTTON 40°/50°/60°/90° - SYNTHETICS 50°/60° programmes are modified to reduce energy
consumption
ª The wash temperature in the 90°/60°/50° programmes is reduced; the temperature in the 40°
programme is increased by 4°.
ª The duration of the wash phase is increased
6.3.10 Sensitive
ª One rinse is added to the COTTON – SYNTHETICS cycles
ª During cotton cycles, agitation is reduced from vigorous to normal
ª Intermediate spin phases are eliminated except for the final two, whose speed is reduced.
6.3.11 Extra rinse
ª Two rinses are added to COTTON cycles, and one rinse is added to SYNTHETICS – DELICATE cycles.
ª Intermediate spin phases are eliminated except for the final two, which are reduced to 450 rpm.
6.3.12 Bleach
ª Ducts water through the bleach compartment at the beginning of the first rinse in COTTON cycles.
ª Pre-wash possible only where there are three solenoids.
ª In models with two solenoids the bleach is not compatible with the pre-wash option.
6.3.13 “Half load” button
ª Eliminates a rinse in the COTTONS programmes.
6.3.14 Easy-Iron
•
ª
ª
ª
ª
•
ª
ª
ª
ª
ª
In COTTON programmes:
Adds three rinses.
Eliminates the intermediate spins.
Performs an impulse spin phase.
Adds an “untangling” phase after the spin cycle.
In SYNTHETICS cycles:
Reduces the heating temperature in 50/60° cycles to 40°C.
Increases the washing time.
Prolongs the cooling phase at the end of the washing phase.
Adds one rinse without spin cycle.
Adds an “untangling” phase after the impulse spin cycle.
6.3.15 Reduced spin speed
ª Reduces the speed of all spins as shown in the table
600 700 800 900 1000 1100 1200 1300 1400 1500 1600
Maximum spin speed (rpm)
450 450 450 450 500 550 600 650 700 750 800
Reduction for COTTON (rpm)
Reduction for ALL OTHER CYCLES
450 450 450 450 450 450 450 450 450 450 450
(rpm)
6.3.16 No spin
ª Eliminates all the spin phases.
ª If selected, three rinses are added in the COTTON cycle and one in the SYNTHETICS cycle.
SOI/DT 2005-01 dmm
14/67
599 36 82 59
6.3.17 Modifying the spin speed
ª Reduces the speed of all spin cycles.
ª The last position can be used for NO SPIN, RINSE-HOLD.
ª If the NO-SPIN option is selected, three rinses are added in the COTTON cycle, and one in the
SYNTHETICS cycle.
6.3.18 Time reduction (Quick)
ª Modifies the structure of the COTTON - SYNTHETICS– DELICATES programmes to obtain washing
time very short (optimization for small or lightly-soiled loads).
ª Reduces the no. of rinses (one rinse less).
ª Increases the water level of the other two rinses.
ª Corresponds to the SHORT- VERY SHORT cycles on the basis of the configuration of the appliance.
6.3.19 Temperature adjustment
ª Used to select the washing temperature compatibly with the limit temperature for the cycle.
ª Can be used during the cycle selection phase: the temperature can be modified only if the heating
phase has not started (in pause mode).
6.3.20 Delayed-start time
• Models with digit
ª It is possible to select, during the programme selection phase, a delayed start from 30 minutes up to 23
hours () 30’) 60’) 90’) 2h) 3h...) 23h) 0h).
ª During the delay phase, the time decreases every hour up to 2h, then by 30minutes.
ª To start the cycle immediately, after the delay time began: press the Start/Pause button, cancel the
delay time by pressing the relative button and press Start/Pause again.
• Models with led
ª Insert a pause before the start of the programme, the delay time is indicated by the corresponding
LEDs.
ª To start the cycle immediately, after the delay time began: press the Start/Pause button, cancel the
delay time by pressing the relative button and press Start/Pause again.
6.3.21 Exclude buzzer
ª The buzzer can be deactivated by pressing a combination of two buttons simultaneously for 5 seconds.
This option depends on the configuration; as a result, the buttons may vary according to the model.
ª If the buzzer is deactivated, the appliance will emit no acoustic signal during selection or at the end of
the cycle; however, the alarm signalling system remains operative.
6.3.22 Electronic drying (WASHER-DRYERS – certain models only)
Three different degrees of drying can be selected for COTTON, and one for SYNTHETIC fabrics:
ª Extra-dry (cotton only)
ª Cupboard-dry (cotton and synthetics)
ª Iron dry (cotton only)
The appliance automatically calculates the drying time is selected using “fuzzy logic”.
The drying phase may be performed automatically (i.e. without interrupting the programme) if selected
together with a washing programme, or as a separate programme.
6.3.23 “Drying time” button
This button is used to select the drying time for COTTON and SYNTHETIC cycles. The time increases by 5
minutes each time it is pressed (from 10 to 130 minutes).
The drying function can be selected for automatic execution after a washing cycle, or as a separate
programme.
SOI/DT 2005-01 dmm
15/67
599 36 82 59
6.3.24 Variation of rinses when options are selected
Night cycle
Easy-iron
No spin
Super rinse
WOOL
HAND WASH
Night cycle
Easy-iron
No spin
DELICATE
Super rinse
SYNTHETICS
Sensitive
PROGRAMMES
COTTON
Very short
Short
Eco
Eco
Normal
Very short
Short
Eco
Normal
Very short
Normal
Normal
Normal
Normal
Normal
Number of rinses for the options
2
3
3
2
3
2
3
3
3
2
3
3
3
2
3
4
4
3
4
3
4
4
4
3
4
5
5
4
5
3
4
4
4
3
4
3
5
6
6
5
6
3
4
4
4
3
6
7
7
6
7
5
5
5
5
5
N.B.: The HALF-LOAD option subtracts one rinse from all COTTON programmes, except for the
VERY SHORT programme.
- The turbidity sensor adds one rinse if there is too much foam or the water is very dirty in all programmes,
except COTTON ECO and SYNTHETICS.
6.4
Display (certain models only)
The following information appears on the display:
ª Three flashing dashes appear when the appliance is switched on
ª The duration of the wash programme appears when the programme is selected. This value is the
amount of time necessary for washing the maximum load of laundry for the type of programme selected.
When the programme is started, the time counts down minute by minute.
ª The end of the programme is indicated by a “0” (when the door can be opened)
ª Delayed start is selected using the relative button. When the START/PAUSE button is pressed, the
time begins counting down and decreases an hour at a time until 2 hrs remain, then the decrease is 30
minutes at a time.
Ö An alarm code indicates a malfunction has occurred.
SOI/DT 2005-01 dmm
16/67
599 36 82 59
6.5
LEDs
These LEDs display different information depending on machine configuration; the end-of-cycle LED is
present on all models.
Type of LED
Prewash
Wash
Prewash/
Wash
Rinse
Spin
Drain
Extra rinse
Rinse Hold
Cycle in
progress
Function
This LED lights up if the selected programme includes a prewash, and lights up during the
prewash phase when the programme is executed.
This LED lights up if the selected programme includes a wash phase, and lights up during
the wash phase when the programme is executed.
This LED lights up if the selected programme includes a prewash or wash phase, and
lights up during the prewash or wash phase when the programme is executed.
This LED lights up if the selected programme includes rinses, and lights up during the
rinses when the programme is executed.
This LED lights up if the selected programme includes a spin phase, and lights up during
the spin phase when the programme is executed.
This LED lights up if the selected programme includes a drain phase, and lights up during
the drain phase when the programme is executed.
This LED lights up when the programme is chosen if an extra rinse has been
selected/stored (if an extra rinse is included in the programme), and lights up during the
extra rinse when the programme is executed.
This LED lights up when the programme is chosen if this option has been selected, and at
the end of the cycle when the machine stops with water in the drum.
This LED lights up while the programme is being executed.
End of cycle This LED lights up at the end of the cycle; it is also used to signal alarms.
Filter clogged This LED lights up at the end of the cycle if the drain filter is clogged.
Detergent
overload
ON/OFF
This LED lights up at the end of the cycle if too much detergent has been used.
This LED lights up when the machine is switched on.
ª This LED lights up when the door is locked by the safety system.
ª The LED switches off when the door is no longer locked.
Door
ª The LED flashes while the door is being unlocked (which occurs masterly on models
with a safety system equipped with a PTC)
Time until end This LED lights up when the display is showing the time remaining until the end of the
cycle.
of cycle
Lights during selection if the programme includes a drying cycle and during the cycle when
Drying
it is in progress.
SOI/DT 2005-01 dmm
17/67
599 36 82 59
7
WASHING PROGRAMMES
7.1
Base programmes for Cotton / Linen: cold-30-40-60-90° (without options)
N.° Phase
Description
Drain
pump
Recirc.
pump
Deterg
Dispens.
Motor Movement
Rpm
Calibration
Level
ON
OFF
2
Flow Calibration
Level
OFF
OFF
PW
3
Water softener Maintenance
Time
OFF
OFF
PW
Water fill
Level
OFF
OFF
PW
Maintenance & Refill
Time
OFF
ON (35/15)
PW
55
Temperature
Time
Time
Time
OFF
OFF
ON
ON
ON (35/15)
ON (35/15)
OFF
OFF
PW
PW
55
55
4
5
6
7
8
9
Pre-wash
1
Heating
Maintenance
Drain
Spin
Level
Level
Time
Level
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
PW
PW
W
55
14
Maintenance & Refill
Time
OFF
ON (35/15)
W
55
15
16
17
Heating
Heating
Heating
Temperature or time
Temperature or time
Temperature or time
OFF
OFF
OFF
ON (35/15)
ON (35/15)
OFF
W
W
W
55
55
55
18
Maintenance heating
Temperature or time
OFF
ON (35/15)
W
19
Maintenance
Time
OFF
ON (35/15)
W
20
21
22
Maintenance
Heating
Heating
Time
Temperature or time
Temperature or time
OFF
OFF
OFF
ON (35/15)
OFF
ON (35/15)
W
W
W
55
55
55
Heating
Temperature or time
OFF
ON (35/15)
Maintenance
Time
OFF
ON (35/15)
Maintenance
Time
OFF
OFF
Maintenance
Time
OFF
ON (35/15)
Maintenance
Time
OFF
OFF
Maintenance
Time
OFF
OFF
Maintenance
Time
OFF
OFF
Cooling
Time
OFF
OFF
Calibration of Turbidity
31
Time
ON
OFF
Sensor
32
Drain
Time
ON
OFF
33
Spin
Time
ON
OFF
34
Drain
Time
ON
OFF
(The data are indicative)
PW
= Pre-wash
W = Wash
AS = Anti-foam control
Only if cycle begins with a wash phase and not with a prewash
W
W
W
W
W
W
W
W
55
55
55
55
55
55
55
55
Wash
4
60°/60°
40°
DRAIN
18/67
4
12
No Movement
No Movement
4
12
No Movement
8
8
8
55/10/3
if 90° 55/8/8
55/10/3
if 90° 55/8/8
8
10
8
10
10
8
10
8
10
8
4
*
1 min.
COT_FIRST_PW_LEV
4 min.
COT_FIRST_PW_LEV
Heating up to 30° or 20 min.
4 min.
Empty Elect. + 14 Sec.
4,5 min. with AS control
4
12
4
12
No Movement
IMP C0
8
30°
WATER FILL
12
No Movement
Calibration
Flow Calibration
Maintenance & Refill
Water fill
SOI/DT 2004-11 dmm
CYCLE
90°
No Movement
55
10
11
12
13
23
24
25
26
27
28
29
30
Movem. Pause
No Movement
8
8
8
8
DRAIN
WATER FILL
1 min.
COT_FIRST_W_LEV
5 min.
COT_SEC_NW_LEV
40° o 40 min.
40° o 80 min.
60° o 40 min. 60° o 80 min. 41° o 10 min. 30° o 80 min. 20° o 80 min.
85° o 40 min.
T° ref.
T° ref.
41° o 5 min.
5 min.
5 min.
2 min.
8
3
8
3
3
8
3
8
3
8
12
20° o 20 min.
5 min.
3 min.
5 min.
60° o 20 min.
5 min.
10 min.
10 min.
41° o 10 min. 30° o 20 min.
10 min.
10 min.
5 min.
5 min.
10 min.
10 min.
15 min.
15 min.
10 min.
5 min.
10 min.
15 min.
10 min.
4 litres
2 min.
No Movement
20 sec.
No Movement
IMP_6
No Movement
Empty Elect. + 14 Sec.
5 min. with AS control
20 sec.
599 36 75-68
7.2
Rinses of Cotton programmes
N.° PHASE
44
45
46
47
48
48
50
51
52
53
2nd Rinse
37
38
39
40
41
42
43
Last rinse
(softener)
36
1st Rinse
35
Description
Drain
pump
Recirc.
Pump
Deterg.
Disp
Water fill
Level
OFF
ON (35/15)
BL
Maintenance & Refill
Time
OFF
ON (35/15)
W
Turbidity measurement
Drain
Spin
Water fill
Maintenance
Wait
Water fill
Time
Level
Time
Level
Time
Time
Level
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON(35/15)
OFF
ON (35/15)
W
Maintenance & Refill
Time
OFF
ON (35/15)
Drain
Spin
Water fill
Water fill
Maintenance
Water fill
Level
Time
Level
Level
Time
Level
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
Maintenance & Refill
Time
OFF
ON (35/15)
Drain
Spin
Level
ON
ON
OFF
OFF
Motor movement
Rpm
Movem. Pause
No movement
55
8
8
55
No movement
No movement
IMP_C6
8
No movement
No movement
No movement
8
W
55
8
8
SF
SF
SF
No movement
IMP_C6
55
8
8
No movement
55
8
8
No movement o
W
55
W
8
No movement
IMPCF_AC
8
CYCLE
COT_FIRST_N_R_TURB_LEV
5 min.
COT_REF_N_R_LEV
6 sec.
Empty Elect.+ 14 sec.
5 min. with AS control
Qt
20 sec.
30 sec
COT_INT_N_R_LEV
5 min.
COT_REF_N_R_LEV
Empty Elect.+ 14 sec
5 min. with AS control
DRY_COND_LEV
COT_LAST_N_R_LEV
30 sec.
Qsf (4 Litres)
8 min.
COT_REF_N_R_LEV
Empty Elect.+ 14 sec
9 min. with AS control
(The data are indicative)
BL = Bleach
SF = Softener W = Wash AS = Anti-foam
Only if Turbidity sensor is featured
Only for Washing machines- Washer-dryers (WD)
SOI/DT 2004-11 dmm
19/67
599 36 75-68
7.3
Cotton / Linen programmes: 90 Eco, 40-60 “energy label” (without options)
N.° PHASE
Description
Drain pump
Recirc. Deterg. Motor movement
Pump
Disp Rpm Movem. Pause
OFF
No movem
Calibration
Level
ON
2
Flow calibration
Level
OFF
OFF
PW
3
Maintenance water softener
Time
OFF
OFF
PW
4
Water fill
Level
OFF
OFF
PW
Time
OFF
ON (35/15)
PW
55
Temperature or time
Time
OFF
OFF
ON
ON
ON (35/15)
ON (35/15)
OFF
OFF
PW
PW
55
55
Level
Level
Time
Level
Time
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
PW
PW
W
OFF
OFF
W
40
Time
Time
Time
OFF
OFF
ON (35/15)
OFF
W
W
40
5
6
7
8
9
Prewash
1
Maintenance & Refill
Heating
Maintenance
Drain
Spin
10
11
12
13
Calibration
Flow calibration
Maintenance water softener
Water fill
14
Maintenance & Refill
15
16
Maintenance
Maintenance
Time
Time
No movem
55
4
12
3
10
3
No movem
OFF
OFF
W
40
Maintenance
Maintenance
Heating
Time
Time
Temperature or time
OFF
OFF
OFF
ON (35/15)
OFF
OFF
W
W
W
40
10
3
No movem
55
8
8
Maintenance heating
Temperature or time
OFF
ON (35/15)
W
55
10
3
Maintenance heating
Temperature or time
OFF
OFF
W
55
10
3
Time
Time
OFF
OFF
ON (35/15)
OFF
W
W
55
Temperature or time
OFF
OFF
W
ON (35/15)
W
10
3
No movem
55/10/3
40° 55/8/8
55
8
8
ON (35/15)
ON (35/15)
OFF
ON (35/15)
OFF
OFF
OFF
W
W
W
W
55
55
55
55
Wash
Maintenance & Refill
18
19
20
23
24
25
Maintenance
Maintenance
26
Heating
Maintenance
Time
OFF
Maintenance
Time
28
OFF
29
Maintenance
Time
OFF
30
Maintenance
Time
OFF
31
Maintenance
Time
OFF
32
Drain
Time
ON
33
Spin
Time
ON
34
Drain
Time
ON
(The data are indicative)
PW= Prewash
W = Wash AS = Anti-foam
Only if cycle begins with a wash phase and not with a prewash
27
10
10
8
8
10
No movem
IMP_6
No movem
COT_FIRST_PW_LEV
4 min.
COT_SEC_PW_LEV
30° o 20 min.
4 min.
Empty Elect. + 14 sec.
4,5 min. with AS control
12
4
12
4
12
No movem
IMP C0
No movem
No movem
55
4
12
No movem
10
40
1 min.
No movem
4
60/50
DRAIN
WATER FILL
17
22
CYCLE
90
3
3
8
8
3
DRAIN
WATER FILL
1 min.
COT_FIRST_W_LEV
5 min.
COT_FIRST_W_LEV
1 min.
22 sec.
1 min.
COT_SEC_EW_LEV
1 min.
22 sec.
67°÷ 64°o 80 min.54°÷45° o 20 min.44°÷ 40° o 80 min.
T° ref.
5 min.
T° ref.
30 min.
15 min.
30 sec.
30 sec.
44°÷ 40°
54°÷45°
67°÷ 64°
2 min.
20 min.
20 min.
10 min.
25 min.
20 min.
5 min.
5 min.
15 min.
Empty Elect. + 14 sec.
5 min. with AS control
20 sec.
20 min.
5 min.
The temperature depends on the water Min.45° Max.53°
SOI/DT 2004-11 dmm
20/67
599 36 75-68
For programmes with two rinses
35
36
37
38
39
40
41
42
43
44
45
PHASE
st
N.°
1 Rinse
7.4.1
Rinses of Cotton / Linen programmes: 90 Eco, 40-60 “energy label” (without options)
Last rinse (softener)
7.4
Drain pump
Recirc.
Pump
Deterg.
Disp
Level
OFF
ON(35/15)
BL
Maintenance & Refill
Time
OFF
ON (35/15)
W
Drain
Spin
Water fill
Water fill
Maintenance
Water fill
Level
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
SF
OFF
ON (35/15)
W
OFF
ON (35/15)
W
ON
OFF
Description
Water fill
Maintenance & Refill
Maintenance & Refill
SF
SF
55
No movem
IMPCF_AC
5 min. with AS control
8
55
8
ON
OFF
SF = Softener W = Wash AS = Anti-foam control
CYCLE
COT_FIRST_E_R_LEV
8 min.
COT_REF_E_R_LEV
Empty Elect.+ 14 sec.
5 min. with AS control
DRY_COND_LEV
COT_LAST_E_R_LEV
30 sec.
Qsf (4 Litres)
4 min.for G20 and G22
COT_REF_E_R_LEV
4 min.for G20 and G22
COT_REF_E_R_LEV
Empty Elect.+ 14 sec
8
No movem
IMP_6
55
8
8
No movem
55
8
8
55
8
8
55/8/8 G20
55/4/12 per G22
Time
BL = Bleach
Movem. Pause
No movem
8
For programmes with three rinses
40
41
42
43
44
45
46
47
48
49
st
1 Rinse
37
38
39
Rinse
36
nd
35
PHASE
2
N.°
Last rinse (softener)
7.4.2
Time
Time
Drain
46
Spin
(The data are indicative)
Only for WD
Level
Level
Time
Level
Time
Motor Movement
Rpm
Drain pump
Recirc.
Pump
Deterg.
Disp
Level
OFF
ON(35/15)
BL
Maintenance & Refill
Time
OFF
ON (35/15)
W
Drain
Spin
Water fill
Level
Level
ON
ON
OFF
OFF
OFF
OFF
W
Maintenance & Refill
Time
OFF
ON (35/15)
W
Drain
Spin
Water fill
Water fill
Maintenance
Water fill
Level
Level
Level
Time
Level
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
SF
Maintenance & Refill
Time
OFF
ON (35/15)
W
Maintenance & Refill
Time
OFF
ON (35/15)
W
Drain
Level
ON
OFF
Description
Water fill
50
Spin
(The data are indicative)
Only for WD
SOI/DT 2004-11 dmm
BL = Bleach
SF
SF
Motor Movement
Rpm
55
55
55
55
55
No movem
IMPCF_AC
9 min. with AS control
8
8
8
No movem
IMP_6
8
No movem
8
8
8
8
8
8
55/8/8 per G19 e G20
55/4/12 per G22
55
CYCLE
COT_FIRST_E_R_LEV
5 min.
COT_REF_E_R_LEV
Empty Elect.+ 14 sec.
5 min. with AS control
COT_INT_E_R_LEV
5 min.
COT_REF_E_R_LEV
Empty Elect.+ 14 sec.
5 min. with AS control
DRY_CON_LEV
COT_LAST_E_R_LEV
30 sec.
Qsf (4 Litres)
8 min. per G19
4 min. per G20 e G22
COT_REF_E_R_LEV
4 min. per G20 e G22
COT_REF_E_R_LEV
Empty Elect.+ 14 sec
No movem
IMP_6
No movem
ON
OFF
SF = Softener W = Wash AS = Anti-foam control
21/67
Movem. Pause
No movem
8
8
599 36 75-68
7.5
Synthetics programmes: cold – 30 – 40 – 50 – 60° (without options)
N.°
PHASE
Description
Drain pump
Recirc.
Pump
ON
OFF
Deterg.
Disp
Motor Movement
Rpm
2
Flow calibration
Level
Level
OFF
OFF
PW
3
Maintenance water softener
Time
OFF
OFF
PW
Water fill
Level
OFF
OFF
PW
Maintenance & Refill
Time
OFF
ON (35/15)
PW
55
Temperature
Time
Time
Time
OFF
OFF
ON
ON
ON (35/15)
ON (35/15)
OFF
OFF
PW
PW
55
55
4
5
6
7
8
9
Calibration
PREWASH
1
Heating
Maintenance
Drain
Spin
CYCLE
Movem. Pause
No movem
60
50
No movem
55
4
4
4
No movem
IMP C0
No movem
No movem
4
No movem
30
1 min.
COT_FIRST_PW_LEV
4 min.
COT_FIRST_PW_LEV
Heating up to 30°
10 min.
Empty Elect.+ 14 sec.
4,5 min. with AS control
12
12
12
Calibration
Flow calibration
Maintenance water softener
Water fill
Level
Level
Time
Level
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
PW
PW
W
55
14
Maintenance & Refill
Time
OFF
ON (35/15)
W
55
8
8
15
Heating
Temperature
Time
OFF
ON (35/15)
W
55
10
3
60°
OFF
ON (35/15)
W
55
3
10 min.
10 min.
10 min.
10 min.
Time
Time
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON (35/15)
OFF
ON (35/15)
OFF
ON (35/15)
OFF
OFF
OFF
W
W
W
W
W
55
55
55
55
55
3
3
3
8
12
60°
15 min.
50°
15 min.
40°
15 min.
30°
15 min.
WASH
10
11
12
13
16
Maintenance
17
Heating
18
Maintenance
19
Maintenance
20
Cooling
21
Maintenance
22
Drain
23
Drain
24
Wait
(The data are indicative)
PW = Prewash BL = Bleach
SOI/DT 2004-11 dmm
Temperature
Time
Time
Time
Time
Time
SF = Softener
55
10
10
10
10
8
4
No movem
4
No movem
*
Water fill
12
No movem
4
40
Drain
15
12
Drain
Water fill
1 min.
SYN_FIRST_W_LEV
3 min.
SYN_SEC_NW_LEV
50°
40°
30°
20°
20°
20° ref
10 min.
15 min.
Qc (4 Litres)
2 min.
Empty Elect.+ 14 sec.
1 min.
6 sec.
W = Wash AS = Anti-foam
22/67
599 36 75-68
Rinses of synthetics programmes
N.°
Description
Recirc.
Pump
Deterg.
Disp
Motor Movement
Rpm Movem. Pause
No movem
No movem
CYCLE
90 60 40 30 *
SYN_FIRST_R_LEV
6 sec.
3 min.
SYN_REF_R_LEV
Empty Elect.+ 14 sec.
OFF
OFF
OFF
OFF
BL
Maintenance & Refill
Time
OFF
ON (35/15)
W
Drain
Time
ON
OFF
29
Drain
Time
ON
OFF
30
31
32
Wait
Water fill
Wait
Time
Level
Time
Time
ON
OFF
OFF
OFF
OFF
OFF
BL
OFF
ON (35/15)
W
ON
ON
OFF
OFF
Wait
Time
Time
Time
ON
OFF
37
Spin
Time
ON
38
39
Wait
Water fill
Time
Level
ON
OFF
40
Maintenance
Time
OFF
OFF
55
10
3
30 sec
Water fill
Level
Time
OFF
OFF
SF
55
10
3
OFF
ON (35/15)
W
55
10
3
Time
Time
ON
ON
OFF
OFF
Qsf (4 Litres)
5 min.
SYN_REF_R_LEV
Empty Elect.+ 14 sec.
4 min. with AS control
34
35
36
41
42
Rinse
33
nd
28
1st Rinse
Level
Time
27
Maintenance & Refill
Drain
Maintenance
Maintenance & Refill
43
Drain
44
Spin
(The data are indicative)
PW= Prewash BL = Bleach
SOI/DT 2004-11 dmm
Drain pump
Water fill
Wait
2
25
26
PHASE
Last rinse
(softener)
7.6
SF = Softener
W = Wash
55
10
3
No movem
55
4
12
No movem
No movem
No movem
55
55
10
No movem
4
3
12
1 min.
6 sec.
SYN_INT_R_LEV
6 sec.
3 min.
SYN_REF_R_LEV
Empty Elect.+ 14 sec.
1 min.
No movem
6 sec.
OFF
IMP_C0
4,5 min. with AS control
OFF
OFF
No movem
No movem
6 sec.
SYN_LAST_R_LEV
SF
No movem
IMP_5
AS = Anti-foam
23/67
599 36 75-68
Programmes for delicate fabrics: cold – 30° - 40° (without options)
N.°
PHASE
Description
Drain pump
Recirc.
Pump
Deterg.
Disp
Motor Movement
Rpm
Calibration
Level
ON
OFF
2
Flow calibration
Level
OFF
OFF
3
Maintenance water softener
Time
OFF
OFF
PW
Water fill
Level
OFF
OFF
PW
Time
OFF
ON (35/15)
PW
55
Temperature
Time
OFF
OFF
ON
ON (35/15)
ON (35/15)
OFF
PW
PW
55
55
OFF
OFF
OFF
OFF
W
W
W
55
PREWASH
1
4
5
6
7
8
Maintenance & Refill
Heating
Maintenance
Drain
Time
Level
Level
PW
Movem. Pause
No movem
No movem
55
4
12
No movem
4
4
4
No movem
12
12
12
No movem
No movem
Time
Level
ON
OFF
OFF
OFF
13
Maintenance & Refill
Time
OFF
ON (35/15)
W
55
4
12
Temperature
Time
OFF
ON (35/15)
W
55
4
12
OFF
ON (35/15)
W
55
4
12
Time
Time
OFF
OFF
ON
OFF
ON (35/15)
ON (35/15)
OFF
OFF
W
W
55
55
BL
W
WASH
Calibration
Water fill
Maintenance & Refill
Water fill
14
Heating
Maintenance
16
17
18
19
Heating
Maintenance
Drain
Water fill
20
21
22
23
25
26
27
28
29
30
Rinses
24
2nd Rinse
1st Rinse
15
Maintenance & Refill
Drain
Drain
Water fill
Maintenance & Refill
Drain
Drain
Water fill
Maintenance
Water fill
Maintenance & Refill
31
Drain
32
Drain
33
Spin
(The data are indicative)
PW= Prewash BL = Bleach
SOI/DT 2004-11 dmm
SF = Softener
Time
Level
Time
OFF
ON (60/20)
Time
Time
ON
OFF
55
ON
OFF
Level
Time
OFF
OFF
W
OFF
ON (60/20)
W
Time
Time
ON
OFF
ON
OFF
Level
Time
Level
Time
OFF
OFF
OFF
OFF
OFF
OFF
SF
55
55
OFF
ON (60/20)
W
55
Time
Time
Time
ON
ON
ON
OFF
OFF
OFF
4
No movem
4
4
No movem
No movem
4
12
12
12
12
No movem
55
4
4
SF
55
4
No movem
4
4
4
No movem
4
DF
*
1 min.
COT_FIRST_PW_LV
4 min.
COT_FIRST_PW_LV
Heating up to 30°
4 min.
Empty + 14 sec.
Drain
SOFT_LEV
1 min.
DEL_FIRST_W_LEV
1 min.
DEL_SEC_W_LEV
40°
30°
T° ref.
T° ref.
10 min.
10 min.
40°
30°
10 min.
10 min.
Empty + 14 sec.
DEL_FIRST_R_LEV
3 min.
DEL_REF_R_LEV
Empty + 14 sec.
1 min.
12
DEL_INT_R_LEV
3 min.
DEL_REF_R_LEV
Empty + 14 sec.
No movem
55
30
Drain
12
No movem
55
CYCLE
40
Water fill
9
10
11
12
Last rinse
(softener)
7.7
12
12
12
12
12
20°
20°
T° ref.
10 min.
20°
10 min.
1 min.
DEL_LAST_R_LEV
30 sec.
Qsf (4 Litres)
3 min.
DEL_REF_R_LEV
Empty + 14 S
1 min.
700Rpm
W = Wash
24/67
599 36 75-68
Wool programmes: cold – 30° - 40°
N.°
PHASE
WASH
1
2
3
4
5
Description
35
Maintenance & Refill
Time
OFF
ON (35/15)
W
35
1
40
Temperature
Time
OFF
ON (35/15)
W
35
1
40
OFF
ON (35/15)
W
35
1
40
Time
Level
Time
ON
OFF
OFF
OFF
W
OFF
ON (60/20)
W
Time
Time
ON
OFF
ON
OFF
Level
Time
OFF
OFF
W
W
16
17
18
19
20
Rinses
15
2nd Rinse
1st Rinse
Drain
Water fill
14
Maintenance & Refill
Drain
Drain
Water fill
Maintenance & Refill
Drain
Drain
Water fill
Maintenance
Water fill
Maintenance & Refill
21
Drain
22
Spin
(The data are indicative)
SF = Softener W = Wash
SOI/DT 2004-11 dmm
Movem. Pause
No movem
No movem
1
40
No movem
W
W
W
8
9
13
Motor Movement
Rpm
OFF
OFF
OFF
OFF
Maintenance
12
Deterg.
Disp
ON
OFF
OFF
OFF
Heating
11
Recirc.
Pump
Level
Level
Time
Level
7
10
Drain pump
Calibration
Water fill
Maintenance & Refill
Water fill
6
Last rinse
(softener)
7.8
No movem
No movem
35
40
No movem
55
4
OFF
ON (60/20)
35
ON
OFF
ON
OFF
Level
Time
Level
Time
OFF
OFF
OFF
OFF
OFF
OFF
SF
35
35
OFF
ON (60/20)
W
35
Time
Time
ON
ON
OFF
OFF
1
1 min.
40
WOOL_INT_R_LEV
3 min.
WOOL_REF_R_LEV
Empty + 14 sec.
No movem
55
SF
4
No movem
1
1
1
No movem
WF
30
*
Drain
SOFT_LEV
1 min.
WOOL_FIRST_W_LEV
1 min.
WOOL_SEC_W_LEV
38°
33°
20°
T° ref.
T° ref.
T° ref.
15 min. 15 min. 15 min.
Empty + 14 sec.
WOOL_INT_R_LEV
3 min.
WOOL_REF_R_LEV
Empty + 14 sec.
12
No movem
Time
Time
25/67
1
CYCLES
40
12
1 min.
40
40
WOOL_LAST_R_LEV
30 sec.
Qsf (4 Litres)
40
5 min.
WOOL_REF_R_LEV
Empty + 14 sec.
1000 rpm
599 36 75-68
Hand wash programmes: cold – 30° - 40°
N.°
PHASE
WASH
1
2
3
4
5
Description
Drain pump
Recirc.
Pump
Deterg.
Disp
Motor movement
Rpm
Calibration
Water fill
Maintenance & Refill
Water fill
Level
Level
Time
Level
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
W
W
W
35
Maintenance & Refill
Time
OFF
ON (35/15)
W
35
Movem.
Pause
No movem
No movem
1
57
No movem
1
57
Heating
Temperature
OFF
ON (35/15)
W
35
1
57
7
Maintenance
Time
OFF
ON (35/15)
W
35
1
57
8
9
Drain
Water fill
Time
Level
ON
OFF
OFF
OFF
No movem
Maintenance & Refill
Time
OFF
ON (60/20)
W
10
11
12
13
15
16
Rinses
14
17
18
19
20
2nd Rinse
1st Rinse
6
Last rinse
(softener
7.9
Drain
Time
ON
OFF
Drain
Time
ON
OFF
Water fill
Level
Time
OFF
OFF
W
OFF
ON (60/20)
W
Maintenance & Refill
35
57
4
35
ON
OFF
ON
OFF
Water fill
Maintenance
Water fill
Level
Time
Level
OFF
OFF
OFF
OFF
OFF
OFF
SF
35
35
Maintenance & Refill
Time
OFF
ON (60/20)
W
35
Time
Time
ON
ON
OFF
OFF
1
1 min.
57
HAND _INT_R_LEV
3 min.
HAND _REF_R_LEV
Empty + 14 sec.
No movem
55
SF
4
No movem
1
1
1
No movem
WF
30
*
Drain
SOFT_LEV
1 min.
HAND_FIRST_W_LEV
1 min.
HAND _SEC_W_LEV
38°
33°
20°
T° ref
T° ref
T° ref
15 min. 15 min. 15 min.
Empty + 14 sec.
HAND _INT_R_LEV
3 min.
HAND _REF_R_LEV
Empty + 14 sec.
12
No movem
Time
Time
26/67
1
No movem
55
Drain
Drain
21
Drain
22
Spin
(The data are indicative)
SF = Softener
W = Wash
SOI/DT 2004-11 dmm
No movem
No movem
CYCLE
40
12
1 min.
40
40
HAND _LAST_R_LEV
30 sec.
Qsf (4 Litres)
57
5 min.
HAND _REF_R_LEV
Empty + 14 sec.
1000 rpm
599 36 75-68
8 DRYING PROGRAMMES
8.1
Drying programme for cotton
DRYING COTTON (full power)
N.°
PHASE
Function
Drain
pump
Fan
LEV
Compart.
(10.0)
COND
Drain
Water fill control
Level
Level
ON
OFF
OFF
OFF
3
Unrolling
Time
ON
OFF
Cooling
Temperature
ON
ON
Calculation of drying time
Time
ON
ON
6
Timer-controlled drying
Time
OFF
ON
7
Timer-controlled drying
Time
ON
ON
8
Cooling
Time
ON
ON
4
5
8.2
DRYING
1
2
Motor
Rpm
55
Movem.
Pause
No movem
8
8
Temperature
Time
55
8
8
10 min.
COND
55
8
8
35°
COND
55
8
8
COT_DRY_TEMP
55
57
3
COT_DRY_TEMP
10 min.
COND
55
57
3
COT_DRY_TEMP
Max. 130 min
COND
55
57
3
35°
10 min.
Temperature
Time
20 min.
Notes
Only when
autodrying is enabled
Not for timecontrolled drying
Only when drying
time >20 min.
Drying programme for synthetics
DRYING SYNTHETICS (half power)
N.°
PHASE
Function
Drain
pump
Fan
LEV
Compart.
(10.0)
COND
Drain
Water fill control
Level
Level
ON
OFF
OFF
OFF
3
Unrolling
Time
ON
OFF
Cooling
Temperature
ON
ON
Calculation of drying time
Time
ON
ON
6
Timer-controlled drying
Time
OFF
ON
7
Timer-controlled drying
Time
ON
ON
8
Cooling
Time
ON
ON
4
5
DRYING
1
2
SOI/DT 2004-11 dmm
Motor
Rpm
55
Movem.
Pause
No movem
8
8
55
8
8
COND
55
8
8
35°
COND
55
8
8
SYN_DRY_TEMP
55
57
3
SYN_DRY_TEMP
10 min.
COND
55
57
3
SYN_DRY_TEMP
Max. 130 min
COND
55
57
3
35°
10 min.
27/67
10 min.
20 min.
Notes
Only when
autodrying is enabled
Not for timecontrolled drying
Only when drying
time >20 min.
599 36 75-68
8.3
8.3.1
Drum movements at low speed and during spin
D55 Delicate movement
D55
8.3.2
8.3.3
sec
rpm
12
4
12
0
55
0
4
-55
N55 Normal movement
N 55
sec
rpm
8
8
8
0
55
0
8
-55
E55 Vigorous movement
E 55
8.3.4
8.3.5
sec
rpm
3
10
3
0
55
0
10
-55
PWL_1 (wool) Delicate movement
PWL_1
sec
rpm
40
1
40
0
35
0
1
-35
PWL_4 (hand wash) Delicate movement
PWL_4
sec
rpm
57
1
57
0
35
0
1
-35
SOI/DT 2005-01 dmm
28/67
599 36 82-59
8.3.6
Cotton/Linen, Synthetics – Intermediate Synthetics Prewash Spin
IMP C0
rpm
FUCS
300
FUCS
450
FUCS
450
650
8.3.7
Cotton/Linen, Intermediate Cotton/Linen Wash Spin
IMP_6
rpm
FUCS
IMP 450
FUCS
450
650
850
1200
8.3.8
sec
x
1
x
30
20
10
60
Cotton/Linen Final Spin
IMPCF_AC
rpm
FUCS
IMP 450
FUCS
450
650
850
1000
1150
1400
1600
8.3.9
sec.
x
1
x
1
x
5
1
sec
x
1
x
30
15
5
95
75
45
65
Synthetics Final Spin
IMP_5
rpm
FUCS
IMP 450
FUCS
450
650
1000
sec
x
1
x
5
10
55
SOI/DT 2005-01 dmm
29/67
599 36 82-59
8.3.10 Delicates Final Spin
DF
rpm
FUCS
IMP 450
FUCS
450
700
1000
sec
x
1
x
35
5
20
8.3.11 Hand Wash and Wool Final Spin
WF
rpm
FUCS
IMP 450
FUCS
450
650
850
1000
sec
x
1
x
5
1
1
20
8.3.12 Easy iron Impulse Cycle EI
EASY_IRON_IMP
rpm
FUCS
450
FUCS
650
FUCS
800
FUCS
900
8.3.13
Intermediate Spin for Cotton/Linen Super-rinse option
CSR
rpm
FUCS
IMP 450
FUCS
450
8.3.14
sec
x
1
x
1
x
1
x
1
sec
x
1
x
90
Movement during drying phase
DRY_MOV
rpm
sec.
3
0
55
57
3
0
-55
57
Notes:
FUCS antiunbalance function before spin phase
x
variable duration
•
in the diagrams the speed is indicated as rotations per minute and the time in seconds.
SOI/DT 2005-01 dmm
30/67
599 36 82-59
8.4
Control of water level in tub
The water fill is carried out in three ways:
ª level fill: is controlled by the electronic pressure switch level
ª time fill: the duration is calculated by the electronic to fill the set quantity
ª level fill and time fill combined
The different levels are determined by the model configuration and depend on the type of tub used.
Level water fill
Type
COT_FIRST_PW_LEV
COT_SEC_PW_LEV
COT_SEC_EW_LEV
COT_SEC_NW_LEV
COT_FIRST_N_R_LEV
COT_FIRST_W_LEV
COT_INT_E_R_LEV
COT_INT_N_R_LEV
COT_REF_E_R_LEV
COT_REF_N_R_LEV
COT_LAST_N_R_LEV
COT_LAST_E_R_LEV
SOFT_LEV
SYN_FIRST_W_LEV
SYN_SEC_W_LEV
SYN_FIRST_R_LEV
SYN_INT_R_LEV
SYN_LAST_R_LEV
SYN_REF_R_LEV
DEL_FIRST_W_LEV
DEL_SEC_W_LEV
DEL_FIRST_R_LEV
DEL_INT_R_LEV
DEL_LAST_R_LEV
DEL_REF_R_LEV
HAND_FIRST_W_LEV
HAND_SEC_W_LEV
HAND_INT_R_LEV
HAND_LAST_R_LEV
HAND_REF_R_LEV
WOOL_FIRST_W_LEV
WOOL_SEC_W_LEV
WOOL_INT_R_LEV
WOOL_LAST_R_LEV
WOOL_REF_R_LEV
DRY_COND_LEV
Description of fill type
Levels for COTTON/LINEN
Water fill first prewash level
Water fill refill prewash level
Water fill second wash level for ECONOMY cycle
Water fill second wash level for NORMAL cycle
Water fill first rinse for NORMAL cycle
Water fill first wash level
Water fill intermediate rinses for ECO cycle
Water fill intermediate rinses for NORMAL cycle
Water fill refill for ECO cycle
Water fill refill for NORMAL cycle
Water fill last rinse for NORMAL cycle
Water fill last rinse for ECO cycle
Water fill
Levels for SYNTHETICS
Water fill first level SYNTHETICS
Water fill second level SYNTHETICS
Water fill first rinse SYNTHETICS
Water fill intermediate rinses
Water fill first level last rinse
Rinse level refill
Levels for DELICATES
Water fill first level DELICATES
Water fill second level DELICATES
Water fill first level first rinse
Water fill first level intermediate rinses
Water fill first level last rinse
Water fill rinse level refill
Levels for HAND WASH
Water fill first level HAND WASH
Water fill second level HAND WASH
Water fill first level intermediate rinses
Water fill first level last rinse
Water fill rinse level refill
Levels for WOOL
Water fill first level
Water fill second level
Water fill first level intermediate rinses
Water fill first level last rinse
Water fill rinse level
Water fill
G 19
P(*) V(*)
100 65
100 65
70
50
80
50
100 20
90
50
140 20
105 20
60
20
60
20
120 20
135 20
40
15
G 20
P(*) V(*)
100 65
100 65
65
45
80
50
160 20
85
40
105 20
105 20
60
20
60
20
120 20
120 20
40
15
G 22
P(*) V(*)
100 65
100 65
60
40
70
55
160 20
85
45
105 20
100 20
60
20
65
20
130 30
120 20
40
15
80
75
130
130
90
60
20
50
20
20
20
20
90
85
135
135
100
60
20
50
20
20
20
20
90
70
145
145
100
60
20
45
20
20
20
20
155
150
170
170
145
150
120
100
120
120
120
120
155
150
170
170
145
150
120
100
120
120
120
120
130
120
160
160
130
150
170
70
120
120
120
100
140
130
180
150
130
100
100
100
100
100
140
130
180
150
130
100
100
100
100
100
125
120
160
130
120
100
100
100
100
100
140
130
170
145
150
110
90
90
120
120
120
85
140
130
180
150
120
110
90
90
100
100
90
85
120
115
150
115
120
110
90
90
100
100
100
85
(The data are indicative)
(*)The measures are expressed in mm.
SOI/DT 2005-01 dmm
31/67
599 36 82-59
9 TECHNICAL CHARACTERISTICS
9.1
EWM2000EVO Electronic control
The EWM2000 EVO electronic control consists of a main PCB
(1) and a control/display board (2).
9.1.1
Functions of the circuit board
PROGRAMM
E
SELECTOR
DISPLAY BOARD
LEDs
µP
Buttons
Display
ELECTRICAL
LOADS
µP
SENSORS
Buzzer
MAIN CIRCUIT BOARD
Ö The circuit board receives signals relative to the cycle settings via the control/display board. The
buttons, the LEDs and the display are also mounted on this board which is connected to the programme
selector.
Ö The board also powers all the electrical components (solenoid valves, washing motor, drain pump,
heating element, door interlock).
Ö The board controls the temperature of the washing water via an NTC sensor, as well as the speed of
rotation of the washing pump according to the signal received from the tachometric generator.
Ö It checks the water level in tub via the level pressure switch and the safety one.
Ö It controls the water level via the flow meter.
Ö It checks the turbidity of the rinse water via the turbidity sensor.
9.1.2
Memory in the control system
µP
Asynchronous
external serial
port
ROM
Power Fail and
machine status
RAM
Synchronous
internal serial
port
EEPROM
(external
to the µP)
Configuration of
the appliance
Description of the
cycle
The main circuit board features an EEPROM memory (external to the microprocessor) which stores in
memory data relative to the configuration, description of the cycle, cycle status in case of a power failure,
and any alarm conditions.
The configuration data (entered in the factory using a computer with a DAAS interface) determine the
functionalities of the appliance (number and type of programmes, options, LEDs etc).
SOI/DT 2005-01 dmm
32/67
599 36 82-59
The overall structure of the microprocessor memory on the main PCB is subdivided into three sections:
ROM
This area of memory contains the software with the general instructions that control the operation
of the appliance, such as those of the electrical components and alarms. The ROM is set up by
the manufacturer of the microprocessor, and cannot be modified.
RAM
This part of memory contains all the variables used during the execution of the wash programme,
which are written in dynamic format. The RAM can be read using a DAAS interface.
EEPROM This area of memory contains:
⇒ the data necessary to restart the appliance in case of a power failure.
⇒ the parameters for the wash cycle, such as water fill level, speed and type of motor movement,
and the temperature during the various phases of the wash cycle. Once written, this data is
protected and, normally, can be read only using a DAAS interface.
⇒ data relative to the configuration of the appliance, such as the speed of the final spin phase,
the volume of the tub, the type of washing system, etc. This data may be entered either via a
DAAS interface or via the control/display board.
SOI/DT 2005-01 dmm
33/67
599 36 82-59
9.2
Analogic pressure switch (electronic)
The electronic pressure switch is an analogic device that controls the water level in the tub. It is directly
connected to the main electronic PCB.
1. air inlet hose
2. diaphragm
3. coil
4. electronic circuit
(oscillator)
5. core
6. spring
7. calibration screw
8. connector
The pressure switch is connected by a hose to
the pressure chamber.
When the tub is filled with water, the pressure
created inside the hydraulic circuit expands the
diaphragm. This in turn modifies the position of
the core inside the coil, thus changing the
inductance and the frequency of the oscillating
circuit.
The electronic PCB, according to the
frequency, recognizes the quantity of the
water in the tub.
Frequency variation according to pressure.
SOI/DT 2005-01 dmm
34/67
599 36 82-59
9.3
Pressure switch
Control of the water level is performed by a two or three-level pressure switch which functions as follows:
•
•
•
contact 11-14: anti-boiling safety level
contact 21-24: anti-boiling safety level
contact 31-32: anti-overflow safety level (not all models)
9.3.1
Pressure switch settings
Anti-boiling level
Anti-boiling level
Anti- overflow level
SOI/DT 2005-01 dmm
Full (mm)
50± 3
50± 3
390± 15
35/67
Refill (mm)
30± 3
30± 3
240±50
599 36 82-59
9.4
Anti-flooding device
1. PCB
8. Drain pump
9. Anti-overflow pressure switch
HV1_S Anti-overflow level sensor
The third pressure switch level (if featured) is used as an anti-overflow safety device: if the pressure switch
contact should open in the FULL position, the PCB actions the drain pump until the pressure switch returns
to the EMPTY position.
9.5
Power supply and programme selection
The main board (3) is powered by the
interference suppressor (1) and by the
closure of the contacts of the main switch
(2). The affected connectors are J6-2
(neutral) and J10-1 (line).
The control/display board (4) is powered at
5V by the main board: through the
programme selector (5) it is possible to
select the programme. The selection of the
options / start is performed through the
board buttons (4).
The buzzer (if featured) (6) is powered by
the display board.
SOI/DT 2005-01 dmm
36/67
599 36 82-59
9.6
Door interlock
There are two types of door interlock:
• voltmetric with PTC: it is always necessary to wait from 1 to 3 minutes before opening the door.
• instantaneous: the door can be opened as soon as the cycle ends.
9.6.1
Voltmetric interlock with PTC
1. Suppressor
2. Main switch (button or
programme selector)
3. Door interlock
4. Main PCB
5. Door pilot lamp closed
• Operating principle
ª When the washing programme is started by pressing the START/PAUSE button, the bi-metal PTC
(contacts 3-5) is powered by the triac on the PCB (J10-2 connector): after 2 – 4 seconds, this closes the
switch (5-4) which powers the electrical components of the appliance (only if the door is closed).
ª The door interlock prevents aperture of the door while the appliance is in operation.
ª At the end of the washing programme, the PCB disconnects the interlock from the power supply, but the
door remains locked for 1 to 2 minutes (PTC cooling time).
Door locked” pilot lamp
ª Certain models feature a pilot lamp which lights to indicate that the door is locked. This pilot lamp
switches off when the door can be opened.
SOI/DT 2005-01 dmm
37/67
599 36 82-59
9.6.2
Instantaneous door interlock
1. Suppressor
2. Main switch (button or
programme selector)
3. Door interlock
4. Main PCB
5. Door pilot lamp off
• Operating principle
ª When the appliance is switched on, the ON/OFF switch closes and the bi-metal PTC (contact 4-2) is
powered; the door, however, is not locked.
ª When the programme starts (START/PAUSE button), the PCB transmits a 20 msec voltage signal to
contacts 4-3 of the solenoid valve (J10-2 connector of the board) (at least 6 seconds must elapse after
switching on); this signal locks the door and, at the same time, closes the main switch (contacts 4-5)
which powers all the components in the appliance.
• At the end of the programme, the PCB transmits two 20 msec signals (at an interval of 200 msec).
- the first signal does not release the door.
- the second signal (which is transmitted only if the system functions correctly) releases the door
interlock and at the same time the contacts of the main switch are opened.
•
ª
-
Conditions necessary for door release
Before transmitting the door release signals, the main PCB checks for the following conditions:
the drum must be stationary (no signal from the tachometric generator)
the water level must not be higher than the lower edge of the door
the temperature of the water must not exceed 50°C.
• Automatic release device
ª In the event of a power failure, if the appliance is switched off, or if the solenoid should malfunction, the
bi-metal PTC cools over a period of 1 to 4 minutes, and then releases the door.
• “Door locked” pilot lamp
ª Certain models feature a pilot lamp which lights to indicate that the door is locked. This pilot lamp
switches off when the door can be opened.
SOI/DT 2005-01 dmm
38/67
599 36 82-59
9.7
Detergent dispenser
The EWM 2000 EVO can control different types of dispensers:
Detergent dispenser
Type
3 compartments
No. of solenoid
valves
Pre-wash/Stains – Wash – Conditioner
(pre-wash and stain are in alternance)
2
Pre-wash/Stains – Wash – Bleach - Conditioner
(the pre-wash/stain and conditioner compartment are
linked together with a “intersection”)
2
Pre-wash/Stains – Wash – Bleach - Conditioner
(pre-wash and stain are in alternance)
3
4 compartments
9.8
Water fill system
The solenoid valves are powered by the main board through two or three triacs. The state of the pressure
switch (full-empty) is detected over two sensing lines.
1.
2.
3.
4.
5.
6.
Main board
Anti-boiling level switch AE2
Anti-boiling level switch AE1
Solenoid valve for prewash
Solenoid valve for wash
Solenoid valve for bleach (on some
models)
7. Heating element
SOI/DT 2005-01 dmm
39/67
599 36 82-59
9.9
Flow meter
Some models of solenoid valves have a built-in flow sensor which measures the quantity of water in litres
that is loaded into the appliance.
If the sensor malfunctions, the water level is controlled by the analogue pressure switch.
Solenoid valve – exploded view
1-Circuit board
2-Turbine
3-Deflector
9.9.1
Main board
4-Diffuser
5-Double filter
6- Reed switch
Turbine
7-Magnet
Operating principle of flow meter
The main components of the flow sensor are:
1.
2.
3.
4.
Contact closed
Contact open
Signal 0
Signal 1
Turbine (with magnet and
counterweight mounted on the
outside)
Reed switch (normally open)
Magnet
Counterweight
Water entering the solenoid valve rotates the turbine (1) and magnet (3), which passes in front of the reed
switch (2), thus closing it. As this contact opens and closes, it generates pulses at a frequency that is a
function of water flow.
The turbine completes 230 revolutions for each litre of water. The operating range of the flow sensor is 0.210 bar.
Using the signal it receives, the microprocessor can calculate the number of litres of water passing through
the solenoid valve.
SOI/DT 2005-01 dmm
40/67
599 36 82-59
Mechanical jamming of solenoid valve
The solenoid valve may jam open without being actuated (which will cause flooding if the pressure switch
controlling the water level does not trip). If this occurs, the electronic control system (which continuously
monitors the flow sensor) will lock the door, start the drain pump and display an alarm.
Low water pressure
If the flow sensor does not generate a signal during water fill even though power is being applied to the
solenoid valve, the cause of this condition may be a closed water tap or clogged filter on the solenoid valve
(with consequent low water pressure). If this occurs, a warning will be displayed and the cycle will continue
for five minutes, after which time an alarm will be signalled.
The solenoid valve controlling residual condensed water operates during the drying phase on washer-dryers.
The alarm is deactivated because the amount of water fill is very small.
9.10 Drain pump
1.
2.
3.
4.
PCB
Anti-boiling pressure switch AE2
Anti-boiling pressure switch AE1
Drain pump
The PCB powers the drain pump via a triac as follows:
ª for a pre-determined period.
ª until the anti-boiling pressure switch closes on EMPTY, after which the pump is actioned for a brief
period or passes to the subsequent phase.
SOI/DT 2005-01 dmm
41/67
599 36 82-59
9.11 Drain pump
1. PCB
2. Anti-boiling pressure switch
AE2
3. Anti-boiling pressure switch
AE1
4. Drain pump
9.12
Aqua Control
The Aqua Control system is a sensor located in contact with the base frame. The sensor detects water leaks
inside the machine (not only during normal operation, but also when the unit is off and plugged in) and starts
the drain pump if a leak occurs.
1.
2.
3.
4.
5.
6.
Main board
Anti-boiling pressure switch AE2
Anti-boiling pressure switch AE1
Drain pump
Interference filter
Aqua Control
Besides supporting the various components on the appliance (drain pump, recirculation pump, shock
absorbers, etc.), the base frame is designed to be a container that collects any water leaks that may occur
(from the drum, from a tube or pipe, etc.). These leaks are directed into an area where a float is installed.
When this float is raised by water, it actuates a microswitch that starts the drain pump. When the switch is
tripped, an alarm is also signalled (if the machine is switched on).
Important: When replacing the drain pump or tube, arrange
the tube so that it doesn’t interfere with the float.
1.
2.
3.
4.
microswitch actuated by float
float
drain tube
cover
SOI/DT 2005-01 dmm
42/67
599 36 82-59
9.13
1.
2.
3.
4.
5.
Heating system
Main board
Anti-boiling pressure switch AE2
Anti-boiling pressure switch AE1
Heating element
NTC temperature sensor
The heating element is powered by a relay on the main board through the contacts on the pressure
switches, which must be closed on “full”.
9.13.1 Heating element
1. Heating element
(1950W)
2. NTC sensor
9.13.2 Temperature sensor
The temperature is controlled by the main board using an NTC temperature sensor.
TEMPERATURE
(ºC)
20
60
80
SOI/DT 2005-01 dmm
RESISTANCE (Ω)
Maximum value
6335
1278
620
Nominal value
6050
1250
640
43/67
Minimum value
5765
1222
660
599 36 82-59
9.14
Turbidity sensor
This sensor is installed only on machines equipped with a recirculation pump.
1. Housing
2. Electronic circuit
3. Transparent tube
The sensor consists of a transparent tube installed in the water circulation circuit. A diode (4) on the side of
the tube emits infrared rays (at a frequency of 2.3 KHz, as generated by the electronic circuit) and a
phototransistor (5) on the other side of the tube is hit by the rays. The amount of current conducted by the
phototransistor depends on the how clear the water is: the clearer the water, the more current the
phototransistor conducts and, as a result, the higher the voltage output from the electronic circuit.
Low Conduction
Medium Conduction
Maximum Conduction
The turbidity sensor operates during the Whites and Colours programmes (COTTON).
It does not operate during the 60°C and 40°C Energy Saving programmes and the Night cycle.
The sensor is calibrated at the end of the wash cycle.
The sensor detects the turbidity of the water at the end of the first rinse and again at the beginning of the
second rinse. The relationship between the two measurements is compared with values programmed on
the board, and the result of the comparison determines whether another rinse is carried out.
SOI/DT 2005-01 dmm
44/67
599 36 82-59
9.15 Motor
1.
2.
3.
4.
PCB
Motor
Anti-boiling pressure switch AE1
Anti-boiling pressure switch AE2
M = rotor
P = motor safety cut-out
S = stator
T = tachometric generator
9.16 Power supply to motor
The PCB powers the motor via a triac. The direction of rotation is reversed by switching of the contacts on
the two relays (K2-K3), which modify the connection between the rotor and the stator.
In certain models (1200-1600rpm), a third relay (K4) is used to power the stator (full or half field) according
to the spin speed
The speed of rotation of the motor is determined by the signal received from the tachometric generator.
During the spin phases, the microprocessor, depending on the software configuration, may perform the antifoam control procedure (if featured) and the anti-unbalancing control procedure.
9.17 Anti-foam control system
The anti-foam control procedure (if featured) is performed via the anti-boiling pressure switch (AB).
Spin phase without foam
Spin phase with little foam
Spin
Anti-foam
( Level AB )
300 rpm pulses
300 rpm
pulses
FUCS
•
•
Spin
FUCS
Spin with little foam: if the contact of pressure switch AB closes on FULL, the spin phase is
interrupted; the drain pump continues to operate and, when the contact returns to EMPTY, the spin
phase is resumed.
Spin with excessive foam in the tub (critical situation): The control system detects whether the
pressure switch commutates 5 times to FULL. In this case, the spin phase is skipped, and a one-minute
drain cycle is performed with the motor switched off; in the case of a washing phase, a supplementary
rinse is added.
SOI/DT 2005-01 dmm
45/67
599 36 82-59
9.18 “FUCS” (Fast Unbalance Control System)
rpm
The control procedure for unbalanced loads is performed dynamically, before each spin cycle, as follows:
ª The phase begins at a speed of 55 rpm; the speed can never fall below this threshold, otherwise the
check is repeated.
ª At intervals of 300 ms, the balance is calculated and compared with predetermined limits. If the value is
less than the lower limit, the speed of the drum is increased by a certain value depending on the
transmission relation between motor pulley/drum; if the unbalancing is higher, it is decreased by the
same value. The reduction in the speed of the drum distributes the washing correctly; this procedure is
repeated until the wash load is completely balanced.
ª Correct balancing of the wash load is achieved at a speed of 115 rpm, after which the spin cycle begins.
Real speed
Selected speed
The Unbalancing Control function takes place in different phases: each phase is characterized by:
ª an unbalancing index (0-1-2-3)
ª an unbalancing threshold value (ex: 350, 650, 850, 1200rpm)
ª a time out (max. time)
• Ending of the FUCS balancing phase
The phase is ended when:
ª The drum rotation speed is 115 rpm (or 85rpm in some cases of unbalancing index). In this case the
spin is performed.
ª In some cases the optimal balancing value is not reached: a reduced spin is performed depending on
the unbalancing.
ª In the worst case, in which all phases are not sufficient to reach a minimum balancing value, the spin is
not performed.
• Example of perfect balancing
Phase 0,
Time-out=60 sec
Phase 1
Time-out=60 sec
115 rpm
55 rpm
SOI/DT 2005-01 dmm
46/67
599 36 82-59
•
Balancing in the available longer interval
1
2
Phase
1
2
3
4
5
6
7
•
3
4
5
Unbalancing index
0
1
2
3
1
2
3
6
7
Time-out (sec)
60
120
60
90
120
90
90
Unbalancing after all phases
In this case the spin (or impulse) is not performed.
SOI/DT 2005-01 dmm
47/67
599 36 82-59
10
DRYING CIRCUIT
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
Fan
Fan motor
Drying heater
Heater casing
Duct
Door seal
Tub
Tube from tub to condenser
Drying condenser
Coupling
Water fill solenoid
Condenser water intake and steam
vent tube
13. Drain filter
14. Drain pump
Automatic drying cycles: the drying time is governed by the microprocessor so that the desired degree of
dryness is achieved.
The drying cycle can be performed at the end of the washing cycle, or as a separate programme. Various
types of drying can be selected:
-
extra-dry
cupboard-dry
iron-dry
Time-controlled cycle: the drying time is selected by the user (maximum 130 minutes for cotton and
synthetic fabrics).
Cooling: a cooling cycle is performed at the end of every drying cycle.
The drying heaters are powered directly by the main board via two relays and the contacts of the safety
pressure switch.
In cycles for synthetic fabrics, drying is performed with only one heater switched on (half power); in
cotton/linen cycles, both the heaters are switched on (full power).
The fan motor is powered via a relay; the condensation solenoid is powered by a triac.
SOI/DT 2005-01 dmm
48/67
599 36 82-59
10.1 Temperature control
The drying temperature is controlled by an NTC sensor positioned on the duct. The heater casing features
two safety thermostats (one of which is a manual-reset type).
1.
2.
3.
4.
5.
6.
7.
8.
9.
Circuit board
Anti-boiling pressure switch AE1
Safety thermostat (auto-reset)
Drying heater
Safety thermostat (manual reset)
Anti-boiling pressure switch AE2
Fan motor
Drying control sensor (NTC)
Humidity control sensor (NTC)
1. Drying temperature control
thermostat (NTC)
2. Safety thermostat (auto reset)
3. Manual-reset safety
thermostat (150°C)
4. Drying heater
NTC sensor: resistance at 25°C
Manual-reset safety thermostat
Auto-reset safety thermostat
Heater
group
Fan capacity
Power
Voltage
Resistance
5000Ω
Normally closed
Opens at 150°±5°C
Normally closed
Opens at 110°±3°C
Closes at 94°±5°
920+920 W
230V
240V
56,5Ω+56,5Ω
61,5Ω+61,5Ω
80 m3 – hour
Calculating the drying time:
In automatic cycles, the NTC sensor fitted to the drying condenser is used to calculate the drying time.
1. NTC temperature sensor
2. Tube from tub to condenser
3. Drying condenser
SOI/DT 2005-01 dmm
49/67
599 36 82-59
11 DEMO Mode
A special cycle has been created for demonstration of the operation of these appliances in retail outlets
without connecting the appliance to the water supply. In this way, the salesman can select any programme;
after starting the cycle by pressing START, the appliance will perform certain phases only, and will skip
those which cannot be performed (water fill, drain, heating).
The cycle takes place as follows:
ª the door locking device is actioned in the normal way (i.e. the door remains locked while the appliance is
in operation, and can be opened at the end of the cycle or in pause mode)
ª motor: all low-speed movements are enabled, while the pulse signals and the spin cycle are excluded
ª the water fill solenoids and the drain pump are disabled
ª display: since the phases of the cycle take place in rapid succession (1 second of the demo cycle is
equivalent to 1 minute of the actual cycle), the time-to-elapse decreases by 1 unit per second.
Remember that the time-to-elapse does not always correspond to the actual cycle time
ª alarms: for reasons of safety, the following groups of alarms remain enabled: E40 (door closed), E50
and E90 (communication between the boards/configuration).
Version with ON/OFF button
Version with ON/OFF button incorporated in the
selector
1. Cancel the set programme and switch the
appliance off.
2. Rotate the programme selector of two
positions clockwise.
3. Press the start/pause (8) button and any of the
option button simultaneously and then, keeping
them pressed, switch the appliance on
through the ON/OFF button (on/off).
4. Hold the start/pause and option buttons down till
the LEDs start flashing (about 5 seconds).
1. Cancel the set programme switching the
appliance off.
2. Press the start/pause (8) button and any of the
option button simultaneously and then, keeping
them pressed, switch the appliance on
rotating the programme selector of two
positions clockwise.
3. Hold the start/pause and option buttons down
till the LEDs start flashing (about 5 seconds).
Attention: the programme selector is not always in the position indicated in the picture; it can be on the right
or on the left of the display board.
The time needed to perform a cycle in DEMO MODE depends on the programme chosen.
11.1 Exiting demo mode
ª Switch the appliance off to exit the demo mode.
SOI/DT 2005-01 dmm
50/67
599 36 82-59
12 DIAGNOSTICS SYSTEM
12.1 Access to diagnostics system
Using a single procedure, it is possible to access to the diagnostics system. After accessing this function,
the following operations can be performed:
ƒ control of the operation of each of the components in the appliance
ƒ read / cancel the alarms
The diagnostics cycles are available only if the communication between the main PCB and the display board
is correct; moreover there should not be configuration errors of the appliance.
To access:
Version with ON/OFF button
Version with ON/OFF button incorporated in the
selector
5. Cancel the set programme and switch the
appliance off.
6. Rotate the programme selector of one
positions clockwise.
7. Press the start/pause (8) button and any of the
option button simultaneously and then, keeping
them pressed, switch the appliance on
through the ON/OFF button (on/off).
1. Hold the start/pause and option buttons down
till the LEDs start flashing (about 5 seconds).
4. Cancel the set programme switching the
appliance off.
5. Press the start/pause (8) button and any of the
option buttons simultaneously and then,
keeping them pressed, switch the appliance
on rotating the programme selector of one
position clockwise.
1. Hold the start/pause and option buttons down
till the LEDs start flashing (about 5 seconds).
Attention: the programme selector is not always in the position indicated in the picture; it can be on the right
or on the left of the display board!
In the first position the function test of the buttons and the corresponding LEDs is performed; by rotating the
programme selector clockwise the operation diagnostics of each component and the reading of the alarms
is carried out.
12.2 Exiting diagnostics system
ª To exit the diagnostics system switch the appliance off, on and then off again.
12.3 Phases of the diagnostics test
Independently of the type of selector, after activating the diagnostics system, the operation diagnostics of
the different components and the reading of the alarms can be performed, by rotating the selector
clockwise.
In models with digit the code of the selector position is displayed for a second.
In the diagnostics cycle all alarms are activated. If during the cycle operation an alarm occurs, the appliance
blocks and the LEDs (and the display) flash indicating the relative code.
SOI/DT 2005-01 dmm
51/67
599 36 82-59
Diagnostics phases
Selector position
Components actioned
Operating conditions
All the LEDs light in
sequence. When a button is
Always activated
pressed, the corresponding
LED lights (and the buzzer, if
featured, sounds)
Function checked
Displayed
parameters (1)
Operation of the
user interface
Button
codification
Door interlock
Washing solenoid
Door locked
Water level below
anti-flooding level
Maximum time 5
minutes
Water ducted
through washing
compartment
(**)Selection
position code
3
Door interlock
Pre-wash solenoid
Door locked
Water level below
anti-flooding level
Maximum time 5
minutes
Water ducted
through pre-wash
compartment
(bleach)
(**)Selection
position code
4
Door locked
Water level below
Door interlock
anti-flooding level
Pre-wash and wash solenoids
Maximum time 5
minutes
Water ducted
through conditioner
compartment
(**)Selection
position code
5
Door interlock.
Bleach/stains solenoid.
Door locked
Water level below
anti-flooding level
Maximum time 5
minutes
6
Door interlock
Washing solenoid if the level
of water in the tub is below
1st level
Heating element.
Door locked.
Water at 1st level.
Heating
Maximum time 10 min.
or up to 90ºC. (*)
1
2
7
8
9
Water ducted through
(**)Selection
bleach/stains
position code
compartment
(**)Selection
position code
Door interlock.
Door locked
(Washing solenoid if the level
Water level at 1st level.
Check for leaks from (**)Selection
of water in the tub is below 1st
the tub
position code
level). Motor (55 rpm
clockwise, 55 rpm counterclockwise, 250 rpm impulse)
Drain and spin;
Door interlock
Door locked
control of
Drain pump
Water level lower than
(**)Selection
congruence in
position code
Motor up to 650 rpm then at anti-boiling level for
closure of level
maximum spin speed
spinning
pressure switches
Drying heater
Fan
Condensation solenoid
Drain pump
Motor
Door closed
(**) selector
position code
Drying
10
Reading/cancelling last alarm
11, 12 ...24
All LEDs light in sequence. Pressing a button the corresponding LED lights (and the Buzzer
sounds, if featured)
---
---
Alarm code
(*) This time is usually long enough for checking the heating system. The time can be increased by repeating the phase
without draining the water; to accomplish this, momentarily select another diagnostic phase and then reselect the
heating test (if the temperature exceeds 80°C, the heating test will not be performed).
(**) See table, page 54
(1) Models with display.
SOI/DT 2005-01 dmm
52/67
599 36 82-59
12.3.1 Display board diagnostics
After entering the diagnostics system, the display board is checked: all LEDs and the display light in
sequence (if featured).
Pressing all buttons, the corresponding LEDs switch on or
those closer; the display shows the hexadecimal code
corresponding to the button codification.
SOI/DT 2005-01 dmm
53/67
599 36 82-59
12.3.2
Programme selector
In the table are indicated the closures between the contact C6 (common) and the other contacts (C1−C5) of
the programme selector in the different positions and the corresponding codification. The code is displayed
only in the appliances with display.
Closure of selector contacts
(C6 is the common)
Selector position
Type 24
positions
1 - Cancel
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Type 12 positions
(C1 is not
featured)
1 - Cancel
2
3
4
5
6
7
8
9
10
11
12
Selector position
C1
C2
C3
C4
C5
0
0
0
0
0
0
1
1
1
0
0
1
1
0
1
0
1
1
1
0
0
0
0
0
1
1
1
1
1
0
0
0
0
1
0
0
0
0
0
0
0
0
1
1
0
1
0
0
1
0
1
0
1
0
0
0
0
0
1
0
1
1
1
1
1
1
0
1
0
0
0
1
1
0
0
1
1
1
0
0
1
1
0
1
0
1
0
1
1
1
0
0
0
0
1
0
1
1
0
0
0
1
0
1
0
1
1
1
0
0
1
1
0
1
0
1
1
0
0
0
Closure of selector contacts
(C6 is the common)
Type 16
C1
Positions
(C1 is not featured)
0
1 - Cancel
0
2
0
3
0
4
0
5
0
6
0
7
0
8
0
9
0
10
0
11
0
12
0
13
0
14
0
15
0
16
C2
C3
C4
C5
1
1
1
1
0
1
0
0
0
1
1
0
1
0
0
0
1
0
1
0
0
0
1
1
1
1
1
0
0
0
0
1
1
0
0
1
1
1
0
1
1
0
1
0
0
1
0
0
1
1
0
0
1
1
1
0
1
1
0
0
0
0
1
0
Display
code
1E
06
14
0C
1C
0A
01
03
09
0E
12
0b
11
18
13
1A
19
1b
05
16
02
04
08
10
Display
code
1F
07
15
0D
0B
0F
13
19
1B
17
1D
01
05
09
03
11
1= This code is shown on the display
SOI/DT 2005-01 dmm
54/67
599 36 82-59
13 ALARMS
13.1 Displaying the alarms to the user (for appliances with Display)
Control of the alarm system can be configured; according to the model, therefore, some or all of the alarms
may be displayed to the user.
Normally all the alarms are displayed to the user except for:
E10 – Water fill difficulty
E20 – Drain difficulty
E40 – Relative to the door lock
E90 – Relative to the configuration
The alarms are active during the execution of the washing programme; except for the alarms relative
to the configuration and power/frequency supply which are displayed also in the selection phase.
The door can normally be opened (except where specified) when an alarm condition has occurred on
condition that:
• The level of the water in the tub is under a level which depends on the configuration of the appliance.
• The temperature of the water is lower than 55°C
Certain alarm conditions require that a drain phase be performed before the door can be opened:
• Cooling water fill if the temperature is in excess of 65°C
• Drain until the pressure switch is on empty, during a max. 5 minute time.
13.1.1 Alarms displayed during normal operation
The type of alarm condition is displayed to the user by the repeated flashing of the END
OF CYCLE LED (0.4 seconds lit, 0.4 seconds off, with an interval of 2.5 seconds between
sequences). This LED is featured on ALL MODELS, though configured in different
positions.
If, for example, the user should forget to close the door, the
control system will detect alarm E41 about 15 seconds after the
start of the cycle; the cycle remains in PAUSE mode and the
display, if featured, would display E40.
Simultaneously the LED end-of-cycle flashes repeating the
sequence indicated in the table.
The four flashing indicate the first of the two digits of the alarm
E41 (the alarms relative to a same function are grouped by
families).
In this case, once the door has been closed, it is sufficient to
press the start button to start the programme.
LED end of cycle
On/Off
Time
(Sec.)
Value
0.4
1
0.4
0.4
2
0.4
0.4
3
0.4
0.4
4
0.4
2.5
SOI/DT 2005-01 dmm
55/67
Pause
between
sequences
599 36 82-59
13.2 Reading the alarm codes
In order to read the last alarm code memorized in the EEPROM on the PCB:
• Enter diagnostics mode
• Irrespective of the type of PCB and configuration, turn the programme
selector clockwise to the tenth position.
13.2.1 Displaying the alarm
The alarm is displayed by a repeated flashing sequence of the two LEDs (0.4
seconds lit, 0.4 seconds off, with an interval of 2.5 seconds between sequences).
The buzzer (if featured) will sound “bips” in synchronization with the flashing of
the LEDs.
• END OF CYCLE LED → indicates the first digit of the alarm code (family)
• START/PAUSE → indicates the second digit of the alarm code (number
within the family)
These two LEDs are featured on all models (though they are configured
differently), and flash simultaneously.
Notes:
• The first letter of the alarm code “E” (Error) is not displayed, since this letter is common to all alarm
codes.
• The alarm code “families” are shown in hexadecimal; in other words:
→ A is represented by 10 flashes
→ B is represented by 11 flashes
→ ...
→ F is represented by 15 flashes
• Configuration errors are shown by the flashing of a series of LEDs.
13.2.2 Examples of alarm displays
Example: Alarm E43 will display the following:
• On the display, if featured, E43
• The sequence of four flashes of the End-of-cycle LED indicates the first number E43;
• The sequence of three flashes of the Start/Pause LED indicates the second number E43;
END-OF-CYCLE LED
On/Off
Time
(Sec.)
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
2.5
SOI/DT 2005-01 dmm
START/PAUSE LED
Value
On/Off
Time
(Sec.)
0.4
1
0.4
0.4
2
0.4
0.4
3
0.4
4
3,3
Value
1
2
3
Pause
Pause
56/67
599 36 82-59
13.2.3 Operation of alarms during diagnostics
All alarms are enabled during the components diagnostics phase. Moving the selector to pass from one
control phase to the other, the appliance exits the alarm condition and performs the selected phase (if the
alarm does not occur again).
13.3 Notes about some alarms
ƒ Configuration alarms
ª E91: the error is indicated by the flashing of all LEDs, E90 is displayed on the display, if featured.
ª E92: the error is indicated by the flashing of LEDs placed over the buttons, E90 is displayed on the
display, if featured.
ª E93: the error is indicated by the flashing of the phase/warning LEDs, E90 is displayed on the
display, if featured.
ª E95: the error is indicated by the flashing of all LEDs, E90 is displayed on the display, if featured.
ª EB1-EB2-EB3 alarms: in case of problems with the power supply, the machine remains in alarm
condition till the frequency or the power supply voltage returns to correct values or the appliance is
switched off. “EB0” alarm family is displayed and it is not possible to enter the diagnostics or to
use “alarm fast display” mode: the alarm complete can be read only when the abnormal situation
terminated.
13.4 Rapid reading of alarm codes
The last alarm code can be displayed even if the programme selector is not in the tenth position
(diagnostics) or if the appliance is in normal operating mode (e.g. during the execution of the washing
programme):
ª Press and hold down START/PAUSE and the option button nearest to the START/PAUSE button for at
least two seconds: the LEDs initially switch off, and then display the flashing sequence corresponding to
the alarm or the code on the display or a message on LCD.
ª The alarm sequence is displayed for the time in which the buttons are hold down
ª The reading system is the same as that indicated in paragraph. 13.2
ª During the time the alarm is displayed, the appliance continues to perform the cycle or, if it is in the
selection phase, it keeps in memory the options previously chosen.
13.5 Cancelling the last alarm with LEDs
It is good practice to cancel the last alarm, after reading the alarm code to check whether the alarm re-occurs
during the diagnostics control after the reparation of the appliance.
1. Select diagnostics mode and turn the
programme selector to the tenth position
(reading of alarm)
2. Press the START/PAUSE and its nearest option
button simultaneously.
3. Hold down the START/PAUSE and option
buttons (about 5 seconds).
SOI/DT 2005-01 dmm
57/67
599 36 82-59
13.6 Table of alarm codes
Alarm
Description
E11
Poor water fill before wash cycle
E12
E13
E21
E22
Difficulty in water fill during drying (maximum time
Tap closed or water pressure too low; solenoid valve; pressure
3 min. water fill in drying during the wash load
switch water circuit; pressure switches; wiring; main board.
unrolling phase)
Drain tube improperly positioned; Water pressure too low;
Water leaks
Water fill solenoid valve is defective; Water circuit on pressure
switch is leaking/clogged; Pressure switch defective.
Drain tube kinked/clogged/improperly positioned; Drain filter
clogged/dirty; Drain pump defective; Pressure switch defective;
Poor draining
Wiring defective; Main board defective; Electrical current leak
between heating element and ground.
Difficulty in water fill during drying or drying
Drain hose kinked; filter clogged: drying condenser clogged; drain
condenser clogged (anti-boiling pressure switch pump faulty; pressure switches faulty; wiring; main circuit board
closed on “FULL”)
defective; current leakage between heater and ground.
E23
Defective triac for drain pump
E24
Malfunction in sensing circuit on triac for drain
pump
E31
E32
E33
E34
E35
Possible fault
Tap closed or water pressure too low; Drain tube improperly
positioned; Water fill solenoid valve is defective; Leaks from water
circuit on pressure switch; Pressure switch defective; Wiring
defective; Main board defective.
Drain pump defective; Wiring defective; Main board defective.
Main board defective.
Action/machine status
Cycle is paused with door locked
Start
Cycle is paused
Start
Cycle is paused with door locked
Start
Cycle is paused
Start
Cycle is paused
Start
Emergency drain procedure - Cycle
stops with door unlocked
Emergency drain procedure - Cycle
stops with door unlocked
Pressure switch;
Malfunction in pressure switch circuit (frequency
Cycle stops with door locked
Wiring;
of signal from pressure switch out of limits)
Main board;
Electronic pressure switch improperly calibrated Tap is closed or water pressure is too low;
(level on electronic pressure switch differs from 0- Solenoid valve;
Cycle is paused
66 mm after initial calibration drain and when anti- Water circuit on pressure switches; pressure switches;
boiling pressure switch is on “empty”).
Wiring; main board;
Pressure switch defective;
Inconsistency between level on electronic
Electrical current leak between heating element and ground; Heating
Emergency drain procedure - Cycle
pressure switch and level on anti-boiling pressure element; Wiring defective;
stops with door unlocked
switch 1(fault persists for at least 60 sec.).
Main board defective.
Water circuit;
Pressure switch defective;
Inconsistency between level on electronic
Electrical current leak between heating element and ground; Heating
Emergency drain procedure - Cycle
pressure switch and level on anti-boiling pressure element; Wiring defective;
stops with door unlocked
switch 2 (fault persists for at least 60 sec.).
Main board defective.
Water circuit;
Cycle stops. Emergency drain
Water fill solenoid valve is defective; Leaks from water circuit on
procedure. Drain pump continues to
Overflow
pressure switch; Pressure switch defective; Wiring defective; Main
operate (5 min. on, then 5 min. off,
board defective.
etc.).
SOI/DT 2005-01 dmm
58/67
Reset
OFF/reset
OFF/reset
OFF/reset
Start
OFF/reset
OFF/reset
OFF/reset
599 36 82-59
Alarm
E39
E3A
Description
Sensing circuit on anti-boiling pressure switch 1
defective
Sensing circuit on anti-boiling pressure switch 2
defective
Internal pressure takeoff is clogged (water level
does not change for at least 30 sec. of drum
rotation).
Defective HV sensing on anti-overflow system
Faulty sensing by heating resistance relay
E41
Door unlocked
E42
Problems closing the door
E43
Defective triac supplying power to door delay
system
E44
Defective sensing by door delay system
E36
E37
E38
E45
Motor power supply triac short-circuited
E52
No signal from motor tachometric generator
E53
Motor triac sensing circuit faulty
E54
Motor relay contacts sticking
E61
Insufficient heating during washing
E62
Overheating during washing
E66
Heating element power relay faulty
E71
NTC sensor for wash cycle defective
E73
E74
E82
E83
OFF/reset
Main board defective.
Cycle stops with door locked
OFF/reset
Water circuit on pressure switches;
Pressure switches;
Motor belt broken;
Main board defective.
Main board defective.
Door lock unit defective; Wiring defective;
Main board defective.
Door lock unit defective; Wiring defective;
Main board defective
Door lock unit defective; Wiring defective;
Main board defective.
Main board defective.
PCB faulty; current leakage from motor or from wiring.
Motor faulty; wiring faulty; PCB faulty
PCB faulty.
PCB faulty; current leakage from motor or from wiring
Heating phase is skipped
---
Cycle stops with door locked
Cycle stops with door locked
OFF/reset
OFF/reset
Cycle is paused
Start
Cycle is paused
Start
(Emergency drain procedure) Cycle
stops
(Emergency drain procedure) Cycle
stops
(Emergency drain procedure) Cycle
stops
Cycle blocked, door locked (after 5
attempts)
Cycle blocked, door locked (after 5
attempts)
Cycle blocked, door locked
Cycle blocked, door locked (after 5
attempts)
NTC sensor faulty; heating element faulty; wiring faulty; PCB faulty. The heating phase is skipped
Safety drain cycle – Cycle stopped
NTC sensor faulty; heating element faulty; wiring faulty; PCB faulty.
with door open
Safety drain cycle – Cycle stopped
PCB faulty; current leakage from heating element to ground.
with door open
Defective NTC sensor; Wiring defective;
Heating is skipped
Main board defective.
Fault in NTC sensor on drying duct (voltage out of Drying NTC sensor (duct) defective; wiring defective; main circuit
range = short-circuit, open circuit)
board defective.
NTC sensor improperly positioned; Defective NTC sensor; Wiring
NTC sensor for wash cycle improperly positioned
defective; Main board defective.
SOI/DT 2005-01 dmm
Reset
Cycle stops with door locked
Fault in NTC sensor on drying condenser (voltage Drying NTC sensor (condenser) defective; wiring defective; main
out of range = short-circuit, open circuit)
circuit board defective.
Error in selector reset position
Error in reading selector
Action/machine status
Main board defective.
Defective sensing by triac on door delay system Main board defective.
E51
E72
Possible fault
PCB faulty (Wrong configuration data). Selector, wiring
PCB faulty (Wrong configuration data). Selector, wiring
59/67
OFF/reset
OFF/reset
OFF/reset
OFF/reset
OFF/reset
OFF/reset
OFF/reset
--OFF/reset
OFF/reset
Start
Heating is skipped
Start
Heating is skipped
Start
Heating is skipped
Start
--Cycle cancelled
OFF/reset
---
599 36 82-59
Alarm
E84
E85
E91
E92
E93
E94
E95
E97
EB1
EB2
EB3
EC1
EC2
EC3
EF1
EF2
EF3
EF4
Description
Possible fault
"Sensing" circuit on circulation pump triac faulty
PCB
(input signal to microprocessor always 0V or 5V)
Circulation pump faulty
Circulation pump;
(incongruency between status of "sensing" circuit wiring;
on circulation pump and status of TRIAC)
main PCB
Communication incongruence between main PCBWiring faulty; Faulty control/display board
display board
Main PCB faulty.
(versions not compatible)
Communication incongruence between main PCBWrong control/display board;
display board
Wrong PCB (do not correspond to the model).
(versions not compatible)
Incorrect configuration of appliance
Incorrect configuration data; PCB faulty.
Incorrect configuration of washing cycle
Incorrect configuration data; PCB faulty.
Communication error between microprocessor and
PCB faulty.
EEPROM
Incongruence between programme selector and
Faulty PCB (Wrong configuration data).
cycle configuration
Frequency of appliance incorrect
Voltage too high
Voltage too low
Solenoid valve inoperative but flow meter
operating
Signal from turbidity sensor out of limits
Signal from weight sensor out of limits
Drain filter blocked
(too long drain phase)
Overdosing of detergent
(too much foam during drain phases)
Control water intervention
No alarm
E00
SOI/DT 2005-01 dmm
Drain filter blocked
(too long drain phase)
Power supply problems (incorrect / disturbance); PCB faulty.
Power supply problems (incorrect / disturbance); PCB faulty.
Power supply problems (incorrect / disturbance); PCB faulty.
Main board defective, Solenoid valve defective
Turbidity sensor defective, Main board defective, Wiring defective
Weight sensor defective, Main board defective, Wiring defective
Action/machine status
Drain, cycle blocked (door open)
OFF/reset
Drain, cycle blocked (door open)
OFF/reset
Cycle interrupted
---
Cycle interrupted
---
Cycle interrupted
Cycle interrupted
OFF/reset
OFF/reset
Cycle interrupted
OFF/reset
Cycle interrupted
OFF/reset
Cycle interrupted
Cycle interrupted
Cycle interrupted
-------
Cycle stops with door locked (after 5
OFF/reset
attempts).
--Start/reset
--Start/reset
Drain tube blocked/kinked/too high;
Drain filter dirty/blocked.
Excessive detergent dosing; drain tube kinked/blocked;
Drain filter dirty/blocked.
Water leakage on the base; faulty water control device.
---
Water drain and cycle blocked
---
Drain tube blocked/kinked/too high;
Drain filter dirty/blocked.
Warning displayed at the end of
cycle (specific LED)
60/67
Reset
Warning displayed at the end of
cycle (specific LED)
---
(specific LED)
--OFF/reset
-----
599 36 82-59
14 Operating time counter
It is possible to display, with a specific procedure, the operating time of the appliance, which is counted from
the first switching on.
This option is available only in models with display. The maximum memorization capacity is 6550 operating
hours.
ƒ Only the operating time of normal programmes is displayed (not diagnostics cycles)
ƒ The actual time of the cycle performed is counted (not the pauses, the delayed start time, rinse hold and
the soak phases)
ƒ The memorization is 30 seconds for each programme
ƒ Only operating hours are displayed (1h and 59min = 1h)
14.1.1 Operating time reading
Version with ON/OFF button
Version with ON/OFF button incorporated in the
selector
1. Reset the set programme and switch the
appliance off.
2. Rotate the programme selector of three
positions clockwise.
3. Press the start/pause (8) and anyone of the
option buttons simultaneously and then, holding
the buttons down, switch the appliance on
with the ON/OFF button (on/off)
4. Keep the start/pause and option buttons down
till the LEDs start flashing (about 5 seconds).
1. Cancel the set programme and switch the
appliance off.
2. Press the start/pause (8) and anyone of the
option buttons simultaneously and then, holding
the buttons down, switch the appliance on
rotating the programme selector of three
positions clockwise.
3. Keep the start/pause and option buttons down
till the LEDs start flashing (about 5 seconds).
14.1.2 Displaying the operating time
The operating time is displayed two digits at a time: the first pair of digits shows the thousands and
hundreds; the second pair shows tens and units.
For example, a total operating time of 6,550 hours will be displayed as follows:
1→
Blank display for two seconds
SOI/DT 2004-11 dmm
2→
The first pair of digits is
displayed for two seconds:
- thousands (6)
- hundreds (5)
61/67
3→
The second pair of two digits is
displayed for two seconds:
- tens (5)
- units (0)
599 36 75-68
15 ACCESSING COMPONENTS
Procedures for accessing specific components on the appliance are described in this section. For
information on other procedures, see the general service manual for P6000 washing machines (599 35 2317)
ƒ
ƒ
15.1
The electrical components must be serviced by qualified personnel only
Unplug the appliance before accessing internal components
Flow meter
If the flow meter malfunctions, the entire
solenoid valve assembly must be replaced.
15.2
Aqua Control
ª Disconnect the connector.
ª Insert a screwdriver into the holes indicated by the arrows
and release the fasteners that attach the component to the
base frame.
ª To attach the cover onto the base frame:
ª First, slide in the part indicated by the arrow (A), then push
the cover in the direction shown by the arrow (B).
SOI/DT 2004-11 dmm
62/67
599 36 75-68
15.3
Turbidity sensor
ª Disconnect the connector.
ª Loosen the clamps (shown by the arrows) and remove
the tubes from the sensor unit.
15.3.1
Installing the turbidity sensor
1. Connection to recirculation pump.
2. End that is inserted into the bellows around the door.
SOI/DT 2004-11 dmm
63/67
599 36 75-68
16
BASIC CIRCUIT DIAGRAM WD
SOI/DT 2005-01 dmm
64/67
599 36 82-59
16.1 Key for circuit diagram WD
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
Electrical components on appliance
Main board
Interference filter
Drain pump
Aqua control
ON/OFF switch (built into programme selector)
Anti-boiling pressure switch AE2
Manual-reset safety thermostat
Door lock unit
Washing heater
Drying heater
Auto-reset safety thermostat
Anti-boiling pressure switch AE1
Anti-overflow pressure switch
Recirculation pump
Solenoid valve for prewash
Solenoid valve for wash
Solenoid valve for condensation
Pilot lamp
Selector
Control/display board
Turbidity sensor
Flow meter
Analogue pressure switch
Fan motor
NTC temperature sensor (drying)
NTC temperature sensor (humidity)
NTC temperature sensor (washing)
Thermal cut-out (motor)
Stator (motor)
Rotor (motor)
Tachometric generator (motor)
SOI/DT 2005-01 dmm
Components on main board
BEL_TY
DOOR_TY
DRAIN_TY
REC_TY
K1
K1
K2
K4
K5
K6
MOTOR_TY
PWELV_TY
WELV_TY
65/67
Condensation solenoid Triac
Door interlock Triac
Drain pump Triac
Recirculation pump Triac
Heating element relay
Drying heating element relay
Fan motor relay
Motor relay: clockwise rotation
Motor relay: anti-clockwise rotation
Motor relay: half field power supply (models with higher spin
than 1200 rpm)
Motor Triac
Pre-wash solenoid Triac
Wash solenoid Triac
599 36 82-59
17
BASIC CIRCUIT DIAGRAM WM
SOI/DT 2005-01 dmm
66/67
599 36 82-59
17.1 Key for circuit diagram WM
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
Electrical components on appliance
Main board
Interference filter
Drain pump
Aqua control
ON/OFF switch (built into selector)
Anti-boiling pressure switch AE2
Door lock unit
Heating element
Anti-boiling pressure switch AE1
Anti-overflow pressure switch
Recirculation pump
Pre-wash solenoid valve
Wash solenoid valve
Bleach solenoid valve
Pilot lamp
Selector
Control/display board
Turbidity sensor
Flow meter
Analogic pressure switch
NTC temperature sensor
Thermal cut-out (motor)
Stator (motor)
Rotor (motor)
Tachometric generator (motor)
SOI/DT 2005-01 dmm
Components on main board
BEL_TY
DOOR_TY
DRAIN_TY
REC_TY
K1
K4
K3
K4
MOTOR_TY
PWELW_TY
WELV_TY
67/67
Bleach solenoid Triac
Door interlock Triac
Drain pump Triac
Recirculation pump Triac
Heating element relay
Motor relay: clockwise rotation
Motor relay: anti-clockwise rotation
Motor relay: half field power supply (models with higher spin
than 1200 rpm)
Motor Triac
Pre-wash solenoid Triac
Wash solenoid Triac
599 36 82-59