- Baby & children
- Toys & accessories
- Remote controlled toys
- AIRTRONICS
- BLAZERsport
- Troubleshooting guide
AIRTRONICS Blazer Sport Troubleshooting guide
Add to my manuals
2 Pages
AIRTRONICS Blazer Sport is a radio control system designed for use in cars and boats. It features a BEC receiver, eliminating the need for a separate battery pack, and the capability to use a separate power supply if desired. The system includes a throttle trigger position gauge and steering reverse switch for precise control, and a throttle reverse switch for added convenience. The receiver antenna should be extended to its full length and kept away from metal parts to ensure optimal performance.
advertisement
TRANSMITTER BATTERY INSTALLATION
1. Press down on the battery cover and slide
in the direction of the arrow to remove.
2. Install 8 pieces “AA” size alkaline batteries as
indicated on the battery tray. Make sure to match
the polarity (+ and -) as shown in the battery
compartment or the transmitter will not function.
3. Install the battery cover in place and slide to close.
WARNING: Improper installation of transmitter batteries can cause serious damage to your system.
To Open slide cover Install Batteries To Close slide cover
Trigger set
Screw
NP-ADJ
A B
RECEIVER AND SERVO CONNECTIONS
Your Blazer or Blazer Sport R/C system is equipped with a BEC receiver to eliminate the need for a separate battery receiver pack, but you can use a separate power supply if desired for your particular model. The following diagram shows a typical connection for the servos and receiver.
Note that the receiver antenna should be located at least 2” (50 mm) away from any servo leads and switches. In electric cars, we recommend that it be at least 4” (100mm) from the electric motor.
Extend the receiver antenna to the full length. Failure to do so will cause loss of control. Do not cut or bend the receiver antenna.
Be careful to avoid any metal parts coming in contact with the servo connectors as this will affect the performance. Insulate the connectors with tape or use tie wraps to avoid contact with metal car chassis.
Please follow the model manufactures recommendations for the correct installation of your radio system in your car or boat.
92621
AIRTRONICS
92621
AIRTRONICS
B
#1
Switch
#2
Throttle Servo
#1
Steering Servo
#2
Contender
Speed Controller
AA Dry Cell Battery Holder
Speed Controller
To Battery
To Motor
Switch
To Battery
To Motor
Throttle Trigger Position Gauge
Troubleshooting Guide
If your radio system does not operate properly, please check the following items:
1. Make sure the batteries are properly installed and
check the polarity (+ and -) again.
2. Check that both the transmitter and receiver power
switches are in the ON position.
3. Check the LED Power Indicators and make certain
that all three are on. If not, replace the batteries.
4. Make sure all the receiver and servo connections
are tight.
5. Make sure that the proper frequency crystals are
installed in the transmitter and receiver.
Steering Reverse Switch
Throttle Reverse Switch
Throttle Trigger Adjustment
Trigger Set Screw must be loosened before adjusting
WARNINGS
DO NOT OPERATE YOUR SYSTEM IF SOMEONE
ELSE IS ON YOUR FREQUENCY AT THE SAM
TIME.
YOUR MODEL CAN CAUSE SERIOUS
DAMAGE OR INJURY SO PLEASE USE CAUTION
AND COURTESY AT ALL TIMES.
DO NOT EXPOSE THE RADIO SYSTEM TO WATER OR
EXCESSIVE MOISTURE.
PLEASE WATER PROOF THE RECEIVER AND SERVOS
BY PLACING THEM IN PLASTIC BAGS OR A WATER
TIGHT RADIO BOX WHEN OPERATING R/C BOAT MODELS.
IF YOU HAVE LITTLE OR NO EXPERIENCE OPERATING
R/C MODELS< WE STRONGLY RECOMMEND YOU SEEK
THE ASSISTANCE OF EXPERIENCED MODELERS OR
YOUR LOCAL HOBBY SHOP FOR GUIDANCE.
AIRTRONICS
Get The Advantage
®
1185 Stanford Court, Anaheim, CA. 92805
Tel:(714) 978-1895 Fax:(714) 978-1540 www.Airtronics.net
Steering Servo
AIRTRONICS
Get The Advantage
®
BLAZER
2 Channel Systems Manual
S por
ERGON
OMIC
CONCE
PTION t
AIRTRONICS
THE CHOICE OF CHAMPIONS
ST-TRIM
LOW
TM-TRIM
FULL
ADVANCED TECHNOLOGY FOR NEW GENERATION
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement