WangYe WY50QT-10 User`s manual

User’s manual
Preface
Thanks for your purchasing the motorcycle WY50QT-58, and sincerely welcome
you to be our motorcycle user. To enjoy a more safe and pleasurable driving, firstly
please familiarity with the manual must carry on before driving. Your personal
safety depends not only on the vigilance and familiar operation skills, but also
relates to whether you are familiar with the mechanical performance. Before driving,
check-up and periodical maintenance are basic requirement. If maintenance and
repair needed, go to our service center for help. If you know the mechanic
knowledge and have the tools, the dealer can offer you help with the maintenance
and repair, like providing the parts catalogue and the spare parts.
This manual explains in detail the correct operation and maintenance, together
with the expectation for your long-time use. Modifications in specification could
cause the discrepancy with some figures and content in the manual, we feel sorry
for that and hold the final right of interpretation. Have a good enjoyment and thanks
again for your purchasing.
The important points to attention

The driver and passenger
This motorcycle is limited to one driver and one passenger (except children younger than 12 years
old). Never exceed the max load capacity of motorcycle.

For the safety, avoid driving the motorcycle in atrocious weather or cold weather (under -12℃).

For the road condition
Only drive on the highroad.
The caution banners about the safety or environment protection stick to the sundries box cover, the
rear carrier, and fuel tank cap. (Being visible before or during driving)

Modifications in specification could cause the discrepancy with some figures and content in the
manual, we feel sorry for that and hold the final right of interpretation.

Please read the user’s manual carefully
You must pay attention to the warning sentence or paragraph.
WARNING
Not following the operation instruction in this manual may cause great damage to you.
ATTENTION
Not following the operation instruction in this manual may cause injury to both you and vehicle.
Regard this manual as a permanent part, even when transfering the vehicle to a new owner, transfer
the manual at the same time.
Contents
Ⅰ. Notice for safe driving
Rules for safe driving …………………………1
Payload ………………………………2
Check up before driving……………………9
Start engine………………….……………13
Drive motorcycle………………….……14
Parts & subassemblies…………………………3
Driving operation………………….……….15
Brake operation………………….………..15
Power off the engine………………….…16
Parking operation………………….………16
Meter and indicator………………………5
Ⅳ、Maintenance and service
Ⅱ. Various parts name and instruction
Ignition switch………………………………5
Fuel meter…………………………………6
Headlight switch………………6
Starting switch……………………………6
Headlight dimmer switch…………6
Turning signal light switch……………………7
Horn switch………………………………7
Steering lock………………………………7
Seat lock…………………………………8
Ⅲ、Operation instruction
Maintenance periodic table………………18
Solution for troubles……………………20
Clean the air filter…………………………22
Battery maintenance………………………22
Idle speed adjustment……………………23
Change oil and clean the filter net…………24
Change the gear oil…………………25
Spark plug……………………………26
Fuse replacement………………………26
Ⅴ、Vehicle storage……………………27
Ⅵ、Vehicle identification………28
Ⅶ、Tool set……………………………28
Ⅸ. Circuit diagram……………………31
Ⅷ、Main technique Parameter………………29
Ⅹ.After sales service……………………32
-1-
Ⅰ Notice for safe driving
Rules for safe driving
1. Many traffic accidents are caused by the inability of car driver to notice the motorcyclist, so the
motorcyclist should try his best to be noticed by other driver

2.
Put on the coat in bright color.
 Drive with great caution in the place with dazzling light or in blind spot. .
Particular care should be exercised at the level crossing of roads, entrance and exit of parking lot
or on the automobile lane.
3.
Never overspeed , otherwise accidents may occur.
4.
You must get the driving license and be familiar with the vehicle. Never lend the vehicle to the
man without driving license or who is unfamiliar with motorcycle.
5.
Avoid driving on the rough road. This can easily result in the operation failure and structural
damage to the vehicle frame
6.
Check up before driving. (Look at page10)
7.
When driving, hold the handlebars and put feet on the footrest.
8. Don’t drive too close to the other vehicles. Never contend for lane, and strictly observe the local
traffic.
-1-
Payload

Admonition:
Only put light goods in sundry boxes or other deposited place.
The deposited shouldn’t be overweighted according to the following blank 1:
Blank 1
Deposited
Weight (kg)
Carrier
5kg
Rear Box
5kg

The max payload of this motorcycle is 75kg, including the weight of the driver,
passenger and goods.

If the motorcycle is over loaded, it will affect the stability and operation of the
motorcycle.

Tie all the goods needed to be carried on the motorcycle.

On the rear shelf seats no child
-2-
Ⅱ. Various parts name and instruction
Parts & subassemblies(Fig1、Fig2)
Front brake grip
Meter & indicator
Ignition switch
Luggage box
Battery
Main stand
-3Fig1
Lable
Rearbrake grip
Rear luggage carrier
Fuel trank
Cushion lock
Air filter
Kick start
Side stand
Fig2
-4-
The broken line(……)indicate the parts unseen in the picture
Meter and indicator(Fig3)
⑴Fuel meter: Indicate the fuel volume in the fuel tank
⑵Right turnning signal : Sparkling when the button turns ight
⑶odometer: Record the mileage
⑷Speedometer: show the speed when the vehicle running.
⑸High beam indicator : When the button is on position“
,
” the high beam
indicator works
⑹Left turnning signal : Sparkling when the button turns left
Ignition switch(Fig4)
⑴Open(
)—when the switch turns to this position,
-5-
Fig3
engine is started and do not pull out the key.
⑵Close(
)—when the switch turns to this position,
engine is stopped and take out the key.
⑶Lock(
)—when the switch turns to lock(
)
Fig4
position, take out the key, don’t turn the handlebar, and don’t start the engine or turn
on any light.
Fuel meter(Fig5)
Fuel meter (5) indicate the fuel volume in the fuel tank. When the needle
points to (F), it indicates that the effective residue fuel is 4.5L.
When the needle points at red section, it indicates the remainder of fuel is 1.2L
F
ig5
-6-
Lighting switches (1)(Fig6)
Lights, a total of three position switch ,is “
“
“
” 、
“
”and “ ”
” In this position, Headlight, position lamps, rear lamps and instrument lights
” In this position, the position lamps, rear lamps and instrument lights.
“ ” In this position, the headlight, rear lamps, position lights and instrument lights
will be shut down.
Starting switch(2)(Fig6)
Fig6
Press this button, the engine is started.(See Fig13)
Fig
6
The front light change switch 1(Fig7)
Press“
”button,to get high beam;Press“
”button,to get low beam
Turn signal light switch 2(Fig7)
When the switch is on“
”turn left,When the switch is on“ ”button, turn right.
Press it down the light turn off.
Fig
7
-7-
Fig 7
Horn switch 3(Fig7)
Press switch, the horn make sound.
Steering lock(Fig 8、Fig 9)
Turn handle left to end, press down ignition key to ( ),the steering setting are locked. Do the
above opposite, it is unlocked.
-8-
Fig8
Fig9
Cushion lock(Fig 10)
Insert the key 1 into the key hole 2, then turn the key clockwise to
open the cushion.
Press down the cushion until a closedown voice is heard. Pull up the
cushion’s rear side to make sure the cushion is locked well, then take
out the key.
Fig10
Ⅲ. Operation instruction
Check up before driving
For safety and preventing trouble or accident, pre-check up is necessary.
Gasoline
-9-
When the pointer or fuel meter is close to red section,
replenish oil. And check whether the tank and the carburetor
are in good condition.
Gasoline tank container:4.5L
Turn the tank cover anti-clockwise to open the fuel tank (Fig11)
Proposal gasoline, octane number is 90 above
Fig 11
Do not replenish oil together with water, dust or other things
NOTICE:
Gasoline is inflammable, it possibly causes fire even exploding on certain condition,
replenish oil only in an airiness place after stopping the engine, no fire in the place of oil
replenishment or oil storage.
Don’t make the top level of fuel above the inlet tube of fuel tank when replenishing, lock
the tank well after replenishment
Gasoline is poisonous, keep your skin or eyes away from it, put it out of touch of
children. If swallow any gasoline unconsciously, see a doctor at once
Inspect the engine oil level(Fig12、Fig13)
1.
Keep the motor steady on the ground, screw up the oil dip rod
and clean it, then reinsert and inspect oil.
- 10 -
2.
If the oil level reach to down limit sign (2), replenish the standard
oil to the level below upper limit sign(3), then
insert and screw down the lid back.
Check if it’s in good situation
Fig 12
Suggested engine number:
SAE-15W/40
3
2
Fig13
The free path of rear brake handle(Fig 14、Fig 15)
Measure the distance of rear brake pedal before detent function,
The free path should between 10-20mm, take the tail of brake handle as standard.
- 11 -
Adjust nut:(A)increase the distance of free path.
(B)reduce the distance of free path
After adjust, the axle pin (2) should touch closely with nut (1) groove after adjust.
(10-20)mm
)
Fig14
Fig15
- 12 -
Abrasion mark of the brake(Fig 16)
(1)
Reference marks
(2)
Indicate marks.
If fully brake. Change the brake block when reference marks and indicate
marks are situated in a straight line.
Notice : Once maintenance for brake system is needed, find
Fig16
the nearest professional repair department . make sure the parts for replacement were
made by our company.
TYRE
check the tyre pressure regularly and adjust if necessary.
Check when the tyre cooled
Check if there is any metal trash or gravel in the groove of tyres
Check if any metal trash or gravel in the groove of tires.
Replace the tyre when it wears out to the abrasion mark.
ADMONITION:
If the tyre pressure dose not accord with the standard, it will possibly cause traffic
accidents.
- 13 -
It is dangerous to use a worn tire because the friction between tyre and road will be
affected
which will possibly bring trouble to driving or even cause an accident.
Start engine (Fig 17)
Put the key into the key hole and turn to “ ”.
Electric starter: press start button (1) to start engine, don’t keep the start
button presssed more than 5 seconds each time.
NOTICE:
Electric starting is based on grasping the brake handle.
If electric starting doesn’t work, there must be a break for 30
seconds before you start the engine with it again
When start the engine in cold condition,
please
warm up engine for 3 minutes before running
The engine will be over heated if it works for a long
time at idle speed in an extremely hot day, you need
to power off the engine immediately.
- 14 -
Fig17
Drive motorcycle:
WARNING:
The temperature of exhaust pipe is much high during driving, you will be injured if
touching with it carelessly, evn within little time after stopping, the tempreture
can also cause injury, so wear trousers to protect your legs against injury.
Wear helmet, glasses , and gloves when driving.
Loose or unsuitable clothes may cause an accident during driving
All the device must be installed according to requirement of the traffic rule.
Take the license with you when driving , each equipment of the motorcycle
should accord with the local traffic law
NOTICE:
Control the speed and payload during the first 1000km.Payload lower than 75kg is
appropriate (including the weight of driver), overspeed or over loading will shorten
the life of engine, and change the crankcase oil after 300 km
- 15 -
Control the speed according to blank 2
Blank 2
Log(km)
Speed (km/h)
0~200
200~500
500~1000
≤20
≤30
≤35
Driving operation
Release Main-Stand and sit on the saddle ,step on the ground by left foot to make
motorcycle plumb with floor.
Turn the throttle when Veh start, put your left leg back to footrest and control the throttle
to make the motorcycle reach good speed. close the accelerograph to slow down
NOTICE:
Do not make a sudden speedup or speed-down with the throttle grip to prevent that
motorcycle rush out unexpectedly.
Driver must release the side stand before driving and try to know the status of
running road
- 16 -
Brake operation:
1. Control the throttle grip
You must control the throttle grip and use both of the brake systems to slow down
NOTICE:Drive with care when driving in bad situation like on moist or runny road, in a
rainy day. Do brake operation, speedup operation or turning operation carefully.
2. Front brake and rear brake work at the same time
Notice:When driving down on a cliffy brae, close the accelerograph entirely and use both of the brake
system to make the speed lower. Don’t do brake operation continuously to make it too hot, which will
affect the performance of brake
Warning : When driving on a smooth or curving road at a high speed, don’t use only
one brake system, you must use both rear and front brake system at the same time to
avoid an accident.
Power off the engine(Fig 18、Fig 19)
Close accelerograph: revolve to the end as the direction of the picture showing (commonly, the
engine will become in idle situation at the moment when you release the throttle grip)
- 17 -
Turn
ignition switch to (
the
)
Fig20
Fig21
Parking operation:
When parking, tun the key to(
)position, put down the support and lock the handle well.(See
P7)
Admonition:Park the motor on a smooth ground, or it may fall down and cause injury.
- 18 -
Notice for anti-theft
Lock the steering and do not leave key in the key hole before you leave.
Park the motor in a carbarn if possible.
Mount a alarm system for your motor.
Ⅳ、Maintenance and service
Maintenance periodic form
This maintenance is based on the odometer , See the Maintenance periodic form
as an important guide for your motor’s maintenance on schedule. You should
increase the frequency of maintenance if you use the motor at a high speed in a
bad situation for a long time.Some main parts of
your motor should be inspected
by a careerman after a repair for most parts or collision, like Frame, hanger, or
turning parts , Repare or replace broken parts to secure your safety
Notice:For the safety and dependability , Never refit. Use the parts of us or parts of same
- 19 -
quality as ours for replacement. Otherwise, the performance and operation function will be
affected.
Warning: For the safety of personnel, no matter whaterve maintenance work carries on, fisrt
power off the engine , park the motor on a good ground and support the motor with stands
well
Notice: the motor without use in winter or having been parking for longer than one month
needs maintenance before driving to check if the fuel , tyre or battery were bad or
corrupted
Maintenance periodic form(blank 3)
Check before maintenance(See P10)
I:Check and adjust it when need.
C:Clean
R:Change
Blank3
Cyc
1
- 20 -
speedometer(×1000km)
4
8
12
Ref
Item
﹡
﹡
Every month
Fuel pipe
I
6
I
Throttle operation
I
I
Core of the air cleaner
﹡
Spark plug
﹡
Valve
﹡
Engine oil
﹡
Engine oil filter
﹡
The carburetor idling
﹡
cold system
(Note1)
(300km)R
I
R
12
I
18
I
page
I
I
15
C/1000km, if need:R
C/2000km, if need:R
I
I
21
22
26
I
(3000 km)R
When change oil:C If need R
I
I
I
I
I
I
24
24
23
Blank3 continue
Cyc
1
Item
Every month
﹡
﹡
Rotate the belt
Gearbox engine oil
﹡
Brake system
Brake cock
Head light
(Note3)
(300km)R
I
- 21 -
speedometer(×1000km)
4
8
12
Ref
page
6
12
18
C/1000km, if need:R
I
25
I
I
I
11
I
I
I
I
I
I
Cyc
1
Item
Every month
﹡
﹡
﹡
﹡
Hanging system
The nuts\bolts
Wheel, tyre
a紧
Turning bearing
(Note2)
I
I
speedometer(×1000km)
4
8
12
Ref
page
6
12
18
I
I
I
I
I
I
I
12
I
* Unless you are an expert on machine and hold a full set of tools and maintenance data, or
leave your motor to a mechanic person.to maintain or repair
* For safety, we claim all of items done by mechanic person.
Note:1、You’ d better shorten the period of maintenance if use the motor in a particularly
moist or dusty area, and when the fuel consumption becomes more and more, and
accelerated effect is bad, you should change some parts.
2、If you usually drive the motor in accidented roads, please go for a maintenance to protect
the performance of the vehicle .
3、change
as the season changes in a cold area.
- 22 -
Solution for troubles(blank 4)
Blank
4
Trouble
phenomenon
Spark
plug no
spark
Cann’t
start the
engine
The spark
is weak
No mixed
air in
cylinder
The cylinder
compresses
reason
Spark plug wear out
Ignition wire wear out
CDI wear out
Ignition switch wear out
Ignition come off or become
flexible
Spark plug gap too small or big
Spark plug pole burn
The spark plug accumulates
carbons
seriously
No
spark
to consult the spark
plug
No fuel
solution
Change
Change
Change
Change
Connect well or firm and tight
Adjust
Change
Clear out
Replenish
Oil mouth stop up
Dredge
Fuel tank pressed the switch to
damage
The
oil passage stops up
Change
Dredge
Clean
Check and clear out
Screw up spark
Change spacer
Air cleaner stop up
Take in system leak
Spark plug seat leak
Cylinder cover leak
- 23 -
strength low
Trouble
phenomenon
The vehicle
has bad
accelerative
performance
The electric
start
does
not work
Riding
Valve seat washer worn out
The piston-ring or the cylinder
The piston-ring
is broken or stored
block
worn seriously
Polish
Change them
Change piston-ring or clear
up the carbon to hinder very much
carbon
Trouble reason
The octane value of the fuel is too low
Blank 4 continue
solution
Change flue
Oil path blocked
Ignition in wrong time
Spark too weak or flameout
Mixed air too dense or too thin
Air leak from the engine
Muffler blocked
Belt wear wear and tear
The automatic clutch roller wear and tear
See “ cann’t start the engine” as reference
Clean oil path
Check wire and change CDI
Check ignition and clear out
Clean adjust carburetor
Check and clear out
Dredge
The clutch is broken
Change
the relay is broken
Change
Battery electricity not enough
Charge
gap between turning bearings is too big
Adjust
- 24 -
Change
Change
unsteady
the brake
does not
work
tyre pressure not enough
Front and rear axle released
The brake block wear and tear superlatively
brake cam wear and tear
Brake cable is broken
Free path too big
pump
Screw up nut
Change
Change
Change
Adjust
Clean the air filter(Fig20)
Take down the fixing bolt of air cleaner cover .
Take out the core from the air cleaner box.
Clean the filter element using compress air or dry brush
or put a new filter in the air clean box.
Do the above oppositely to reinstall the air filter.
NOTICE:
Never use gasoline or low burning point solvent to clean
Battery maintenance(Fig21)
It is adopted the airtight battery (don’t add water)
- 25 -
Fig20
NOTICE:Never take apart upper cover of the electrolyte.
If you don’t use the motor for a long time. please take off
the battery and keep it in a ventilated and dry place
If the peg of battery is corroded. Please take it off and
Fig21
clean.(use boiled water)
NOTICE: Turn off the ignition switch before taking apart the battery. Taking negative
terminal first and positive terminal next, when installing, just opposite to
above procedure
Idle speed adjustment(Fig22、Fig23)
The carburetor has been adjusted to the best situation before selling out.
If it is not well adjusted, ask a professional person to adjust it as the following
instruction.
Warm up several minutes after engine starts
Screw the bolt 1 in slightly to increase the idle speed,
then screw in the mix ratio screw first and next out
from the idle speed adjustment, screw to gain the
- 26 -
Fig22
minimum torque.
After adjusting the idle speed, adjust free path of the throttle to
2-4mm.
After adjusting, the engine speed can transit steadily when
suddenly apply the throttle instead of turning off.
Fig23
Change oil(Fig24)

Change oil only when the engine is not cooled yet and the vehicle is
supported by jiffy Stand, to pour out all the oil completely and quickly
Clean the oil filter net
 Screw out the the cover of oil hole /oil dip rod and the cover of oil filter
screen,Take out oil hole cover and oil filter 1 then take strainer 2 and spring 3.
Clean the oil filter net using liquor
Fill in the oil filter net,spring and the cover of oil filter screen.
Inpour standard oil into the engine, not exceeding the upper mark,
When measuring the oil level, do not screw down the cover of oil hole / oil dip rod.
Fill in the cover of oil hole / oil dip rod
Start engine and keep it working at idle speed for few
- 27 -
Fig24
minutes, then turn it off.
Measure the oil volume of engine again to make sure it
does not leak.
Change gear oil(Fig 25)
We suggest oil octane number:
SAE
80W/90(you can use antifreezing oil in very cold area)
Oil capacity
Resolving capacity: 0.10L
Changing capacity: 0.09L
Place the vehicle by the main stand.
Screw out the immersion bolt 1 and oil-drain bolt 2.
NOTICE:When draining the oil, the engine needs a certain temperature,
use the main stand to support the motor, make sure all the oil is drained.
Clean the drain bolt and then re-install it.
Inject oil into the hole of the immersion bolt slowly till the oil spill over.
Fix the immersion bolt and screw it tight.
- 28 -
Fig25
Spark plug(Fig26)
1
Spark plug specification
2
(0.6~0.7)mm
Standard: C7HSA(NGK) or A7T、A7RT
Disconnect the joint of the spark plug cover and
take apart the spark plug with special spanner
Check if there is any burnning ash or accumulated dirt on electrode or
porcelain head, if it singed badly, replace the spark plug, Clean the ash or
dirt with plug cleanser or a brush
Normally the gap between side electrode (1) and
Center electrode (2) is 0.6-0.7 mm
Don’t use other kind of spark plug with different specification.
Fuse replacement
The rated electric current of the fuse is 15 A. If the fuse often burns down, it indicates the
short circuit or overload in the electric system. Ask the serviceman to repair it, and never
- 29 -
fig26
use the brass wires to replace the fuse.
Ⅴ.Vehicle
Storage
STORAGE
If the vehicle hasn’t been used for a long time, some steps should be taken to prevent
malfunction and damage to the parts. Besides, before the long-time storage, proper repairs
should also be done.
Change the engine oil.
Drain out the fuel in the fuel tank and oil in the carburetor.
Warning: Gasoline is inflammable and may cause fire and even explosion on certain
conditions. Therefore, no fire when draining.

Take apart the spark plug, inject about 15~20ml oil into the cylinder, step down the kick
pedal several times and then fix the spark back on.

Take apart the battery and place it in a place without strong light or frozen ice, charge it
every month.

Clean the vehicle and wipe it dry, coat the wax on the surface of the paint, and anti-rust
- 30 -
oil on other metal parts.

Cover the vehicle and put it in a cool place.
Use the vehicle after long-time storage
Take off the cover and clean the vehicle. You should change the oil after 4 months above
storage.
Charge the battery if necessary, and fix it on.
Check all the parts before driving.(see p9), ride motorcycle in a low speed in non-busy
area, make sure the safety.
- 31 -
Ⅵ.
Vehicle identification.
Position of the model code, vehicle identification number and label(Fig 27)
Provide the numbers above when register to get the license ,do yearly inspection, and enjoy
the after-service .
the rivet for fixing name plate is on the right side of main stand.
Vehicle identification number
Model code
Engine Number
Fig27
- 32 -
Ⅶ. Tool set
Toolbox(Fig28)is placed in the luggage box under the saddle, and
toolbox contains the following tools:
Wrench 8x10mm
Wrench 12x14mm
Screwdriver
Hexagonal wrench
Handle of screwdriver
Sleeve wrench 18.5x17
- 33 -
Fig28
Ⅷ. Main technique Parameter
Table5
Item
Parameter
L×W×H (mm)
Wheel Base (mm)
Ground
(mm)
Clearance
Dry
Weight
kg
Max
Payload
kg
Turning
Steering
Angle of
Handle
º
V=40km/h
Item
Front Tire
Rear Tire
1905×705×1160
1315
140
92
75
Pressure Of Front
Tire
Pressure kPa
Of Rear
Tire (kpa)
Derailleur
Auto Stepless
9.39~26.52
Fr Brake
Distance
m
Speed-down average
m/s22
Speed
Ratio
of
Derailleur
Rr Brake Distance
m
≤21.78
≥3.4
≤26.86
≤48
Max Speed km/h
≤50
Engine type
Economic
Oil
Consumption
Climbing
Performance
≤2.3/100km
Bore/stroke(mm)
≥4.5
Displacement(ml)
- 34 -
Parameter
120/70-12
120/70-12
180
200
Speed-down average m/s2
≥2.7
139QMB
Single/4stroke/air-cool
39.0×41.5
49.6
Inclination
Start Model
Battery
Oil capacity L
-1.3%
Electric/Kick
12V 7Ah
4.5
Add table5
Item
Lubricating Way
Rated Power
Max Torque
Parameter
Press and splash
2.2/7000 r/min
Item
Fuse
Headlight
3.0/6000 r/min
Tail Light/Brake light
12V 18W/18W×2
12V 5W/21W
Compression Ratio
10.5:1
前位灯
12V 5W
Specification of Spark
Plug
Spark Plug Gap mm
C7HSA(NGK)or A7T、A7RT
Turning light
Fuel Brand
12V 10W×4
RQ90
0.11
Idling Speed r/min
0.6~0.7
(1500±150)
Lubrication Capacity of
Crankshaft Case
0.8
Trademark of gear
Ignition way
Parameter
15 A
Oil
Capacity,
Gearbox
L
Gear Oil Brand
SF 级 SAE 15W/40
CDI
- 35 -
Clutch
Valve gap
SAE 80W/90
Automatically centrifugal
mm
0.03~0.05(cool)
Ⅸ. Circuit Diagram
- 36 -
X. After sales Service
- 37 -
Ⅰ.General rules:
After your buying the WangYe motorcycle, please drive and maintain it as the manual instruction.
According the regulation of document No. (1997) 205, we guarantee you the following services in one year
or 6000km when you show us the warrants.
Ⅱ.Guaranteed Service
1.
Free-repair service
We offer you free-repair service for the malfunction in the range of change and return in our
guarantee.
2.Change service range
2.1We offer you free-change service for the performance malfunction occurred within 8 or 15
days, the malfunctions occur in the regulation of document No. (1997) 205, the user select to
change or repair.
2.2 The malfunctions that occur 15 days later in the regulation of document No. (1997) 205,
and still exist after 2 times repairs.
2.3 We offer the fittings according to the document, if it isn’t ok after 90 days of repairing.
3. Return service range
3.1 We offer you return, change and free-repair service for the performance malfunction occurred
- 38 -
within 7days of sales; the malfunctions occur in the regulation of document No. (1997) 205.
3.2 The user can ask for returning if the malfunctions are accord with the change service but we
haven’t the same model.
3.3 If the malfunctions are accord with the change service, and we have the same model, but the
user still claims return, we will charge 2% as depreciation charge.
Ⅲ. No service
1.Exceed the warrant date of one year.
2.Exceed mileage 6000km, the odometer is broken, and change odometer.
3.Not following the driving and maintenance instruction on the manual.
4.Disassemble the vehicle by yourself.
Ⅳ. Procedure
1.
The user should specify the detail malfunctions and the motor code and engine code so that
we can analyze and dispose the malfunctions.
2.
We charge of the fee within the repair and change service. User charges all that out of the
service, and we can offer the technical service.
3.
Contact telephone:
- 39 -
After-service: 0576-84067902
0576-84359612
Sales Tel: 0576-84067899
- 40 -