Motorola H715 - Headset - Over-the-ear User`s guide

BEFORE YOU
BEGIN
Before using this product, read the Important Safety and
Legal Information pamphlet and follow its instructions.
motorola
H715
Take a moment before you get started to
familiarize yourself with your new
H715 Headset.
Call
Button
Volume
Buttons
Multi-Color
Indicator Light
Boom
Quick Start Guide
Speaker
(on reverse
side)
1
CHARGE
Your Headset's Battery
2
Microphone
(on reverse side)
START BLUETOOTH
FEATURE
Your Phone
Charge your headset's battery for 2 hours:
Your phone's Bluetooth feature is off by default.
To use your headset, you must turn on the
Bluetooth feature in your phone.
For most Motorola phones (at the main menu):
1 Press M (Menu ) > Settings > Connection >
1 Plug the Motorola charger into the end of
Bluetooth Link > Setup.
the headset.
The indicator light turns red when the battery
is charging. It may take up to 1 minute for
the indicator light to turn on. When the
headset's battery is fully charged (about 2
hours), the indicator light turns green.
2 Disconnect the charger.
Note: Headset is not functional while charging.
Note: This product uses a lithium ion, rechargeable,
non-replaceable battery. Under normal use, the expected life
of the rechargeable battery is approximately 400 charges.
2 Scroll to Power.
3 Select Change.
4 Scroll to On.
5 Press Select to turn on the Bluetooth
feature. The Bluetooth feature remains on
until you turn it off.
Note: These steps are for most Motorola phones.
For other phones, see your phone's user's guide.
3
PA
Your Heads
Before you can use your headset, you must pair
(link) it with your phone.
Step A - ENSURE HEADSET IS IN PAIRING
MODE
AIR
set and Phone
Step B - SET YOUR PHONE TO LOOK FOR
YOUR HEADSET
For most Motorola phones:
1 On your Motorola phone, press M (Menu ) >
Open the headset boom to power on the
headset and initiate pairing. After a few
moments, the indicator light will be steadily lit
in blue to indicate headset is in pairing mode.
Indicator Light
(steadily blue
for pairing mode)
If the headset does not enter pairing mode,
see TROUBLESHOOTING for help.
Motorola, Inc.
Consumer Advocacy Office
1307 East Algonquin Road
Schaumburg, IL 60196
www.hellomoto.com
1-877-MOTOBLU
1-888-390-6456 (TTY/TDD United States for
hearing impaired)
Guide Number: 6809516A41-C
Settings > Connection > Bluetooth Link > Handsfree
> Look for Devices.
The phone lists Bluetooth devices it finds.
2 Select Motorola H715.
3 Select OK or Yes to pair your headset with
4
5
your phone.
Enter the passkey: 0000
Select OK.
When your headset successfully pairs with
your phone, the indicator light flashes
purple and blue.
Note: These steps are for most Motorola phones.
For other phones, see your phone's user's guide.
4
TEST AND USE
Your phone and headset are now paired and
ready to make and receive calls. To confirm they
are operating properly, make a call:
1 Place the headset over your ear.
2 On the phone, dial the number you want to
call and press SEND key on your phone.
3 If your phone and headset are successfully
paired, you will hear ringing on the headset.
Bluetooth QD ID: B013079
MOTOROLA and the Stylized M Logo are registered in the US
Patent & Trademark Office. The use of wireless devices and their
accessories may be prohibited or restricted in certain areas.
Always obey the laws and regulations on the use of these
products. The Bluetooth trademarks are owned by their
proprietor and used by Motorola, Inc. under license. All other
product or service names are the property of their respective
owners.
© Motorola, Inc. 2008.
After you have successfully paired your phone
and headset, you don't need to repeat these
steps. For daily use, ensure that your headset is
turned ON and that your phone's Bluetooth
feature is ON.
To conserve power, close the boom to turn your
headset off. Re-open the boom to make a call.
USING A SE
Multipoint technology allows you to make and
receive calls from two Bluetooth enabled
devices like your personal and business phones.
To pair a second phone to your headset, follow
these steps:
1 Turn off any phones or devices that are
2
3
already paired with your headset.
Turn off your headset by closing the headset
boom.
Perform Step 2 (“Start Bluetooth Feature”),
and Step 3 (”Pair”), and Step 4 (”Test and
Use”) to pair your headset with your second
phone.
To reconnect your headset with your first phone
(and thus be connected to both phones), follow
these steps:
1 Turn on first phone.
TIPS FOR USING H715
WITH TWO PHONES
Use the following tips when using H715's
multipoint technology:
●
Incoming calls can be answered from both
phones:
– When answering a call, the idle phone is
disconnected from the headset.
– When the call ends, the idle phone is
automatically reconnected to the headset.
●
Last number redial dials the last outgoing call
made from either phone.
●
Voice dial is accessible from either phone via
different key actions:
– For your primary device (last paired
phone), tap the Call button until you hear
the tone.
– For your secondary device (other paired
phone), tap the Call button and either
Volume button until you hear the tone.
ECOND PHONE?
2 Use your first phone to connect to your
headset.
a On your Motorola phone, press M (Menu )
> Settings > Connection > Bluetooth Link >
Audio Devices.
The phone lists Bluetooth devices it finds.
b Select Motorola H715.
c Select OK or Yes.
Your headset is now connected to both
phones. The last paired phone (your second
phone) is now your primary phone for voice
dial functionality.
After you have successfully paired both phones
with your headset, you don't need to repeat
these steps. For daily use, ensure that your
headset is turned ON and that your phone's
Bluetooth feature is ON.
TROUBLESHOOTING
My headset will not enter pairing mode.
Make sure that any devices previously paired with the
headset are turned off. If the indicator light is flashing in blue,
first turn off the other device, then close and reopen the
headset boom. The indicator light becomes steadily lit in
blue indicating the headset is now in pairing mode.
My phone doesn't find my headset.
Make sure the indicator light on your headset is on (lit in
blue) and steady when your phone is searching for devices
(see step 3).
My headset worked before but now it's not working.
Make sure your phone is on and the Bluetooth feature is
turned on in your phone (see step 2). If the Bluetooth feature
was turned off or was turned on only temporarily, you may
need to restart the Bluetooth feature (see step 2) and pair
your phone and headset again (see step 3).
My headset will not pair with my phone.
Open the boom flip. Press and hold both Volume buttons
and the Call button for more than 10 seconds. The indicator
light flashes blue 3 times and then become steadily lit. The
headset is now in pairing mode (see step 3B) to complete
the pairing process.
Support.
If you need more help, contact us at
1-877-MOTOBLU or visit us at
www.hellomoto.com/Bluetoothsupport
Features and
Functions Guide
TURNING HEADSET
ON AND OFF
To turn your headset on, open the headset
boom. The indicator light flashes blue (if
connected with a device) or is steadilly lit (if
ready to be paired).
To turn your headset off, close the
headset boom. The indicator light will turn
off.
IMPORTANT:
Be sure to first follow the
Quick Start Guide
on the reverse side
of this guide
to complete initial setup
of your H715.
WEARING THE HEADSET
1 Open the headset boom, then open the
earhook.
2 Loop the earhook over your ear.
3 Press the headset to your ear.
4 Point the headset boom towards your
mouth.
Multi-Color
Indicator Light
CHANGING FOR USE
ON OTHER EAR
You can wear your H715 headset on your left or
right ear. The headset comes ready for the right
ear. To change the headset for the left ear:
1 Open the headset boom,
then open the earhook
(90° from the headset).
2 Gently lift and pull the
top of the earhook up
and off the upper hinge
pin. Then, pull it away to
remove it.
3 Flip the headset over.
1 Open Earhook
2 Pull Earhook
Up
4 Hook the bottom of the
earhook onto the lower
hinge pin, then lift and
pull the top of the
earhook over the upper
hinge pin.
Hinge
Pin
CHANGING VOLUME
BUTTON ORIENTATION
You can also change the orientation of the
volume buttons on your headset.
1 Close the boom to turn the headset off.
2 Press and hold down the desired
"volume up" button and open the boom.
Keep the button pressed until the
indicator light flashes blue three times.
Volume
Buttons
Call
Button
European Union Directives
Conformance Statement
Hereby, Motorola declares that
this product is in compliance with:
• The essential requirements and
other relevant provisions of Directive
1999/5/EC.
QUICK BATTERY
CHECK
When not in a call, open the boom to check
your headset's battery charge level by
pressing and holding both Volume buttons.
The indicator light displays charge status
until you release the buttons. See below for
details on indicator light and available talk
time based on charge status.
Headset Indicator
Red
Yellow
Green
MAKING CALLS
Function
Action
Make a voice dial call
(Primary phone)
Tap the Call button
and speak the
name after the tone
Make a voice dial call
(Secondary phone)
Tap the Call button
and either Voume
button and speak the
name after the tone
End a call
Tap the Call button,
and hear a
high-to-low tone
Answer a call
Open the boom or tap
the call button (if
boom is ready open),
hear the ring tone,
then a low-to-high
tone
Reject a call
Press and hold either
Volume button until
you hear a tone
• All other relevant EU Directives.
Product
Approval
Number
The above gives an example of a typical Product
Approval Number.
You can view your product’s Declaration of Conformity
(DoC) to Directive 1999/5/EC (to R&TTE Directive) at
www.motorola.com/rtte. To find your DoC, enter the
product Approval Number from your product’s label in
the “Search” bar on the web site.
Available Talk Time
Less than 2 hours
2 to 4.5 hours
Up to 6.5 hours
Note: Some features are phone/network dependent.
MAKING CALLS CONTINUED
Function
Action
Redial last call
Press and hold the
Call button until you
hear a tone
Press and hold the
Call button (places
first call on hold), and
hear a tone
Press and hold either
Volume button
Answer a second
incoming call
Reject second incoming
call
Transfer a call from the
headset to the phone
Mute or unmute a call
Press both Volume
buttons and Call
button, and hear a
descending tone
Tap both Volume
buttons until you hear
a mute tone
Note: Your H715 supports both Handsfree and Headset
Profiles. Accessing call functions depends upon which
profile your phone supports. See your phone's user's guide
for more information.
INDICATOR LIGHT
With No Charger Plugged In
Headset Indicator
Off
Headset Status
Power off
Three blue flashes
Powering on/off
Steady blue
Pairing mode
AUDIO TONES
Audio Tone
Ring tone
Short tone
High to low tone
Two short tones when
pressing Volume button
during a call
Ascending tone
Low tone
(repeated every
15 seconds)
Descending tone
Low to high tone
No audio indications;
deteriorating quality
Two tones
repeated every minute
Headset Status
Incoming call
Phone network not
available
End call
Volume at minimum
or maximum
Mute enabled
Mute reminder
Mute disabled
Connection
confirmation/voice
activation
Out of range
Low battery
INDICATOR LIGHT CONTINUED
With No Charger Plugged In
Headset Indicator
Headset Status
Red flash
Idle (not connected
to phone)
Slow purple pulse
Connected call muted
Quick blue/purple flashes Pairing successful
Quick red flash
Low battery
Quick blue flash
Incoming/outgoing call
on primary phone
Slow blue pulse
Connected (on a call)
Tip: Set your primary and secondary phones to different ring
tones to know which phone is ringing when wearing the
headset. See "Tips for using H715 with Two Phones" for
more information.
Slow blue flash
Standby (not on a call)
Note: After 20 minutes on a call or of inactivity, the light stops
flashing to conserve power, but the headset remains on.
Note: To disable the indicator light, press and hold both
Volume buttons while turnng headset on.
INDICATOR LIGHT
With the Charger Plugged In
Headset Indicator
Headset Status
Red
Battery level less
than 50% charge
Yellow
Battery level more
than 50% charge
Green
Charging complete