Craftsman 973.111430 Owner`s manual

10/03/01
WED 13:43
FAX 864
064
3314
RYOBI CUSTOMER SERVICE
_002/015
Owner's Manual
318 in., 16.8 VOLT CORDLESS DRILL-DRIVER
Variable Speed / Reversible
Model No.
973.111430
Save this manual for
future reference
• Safety
• Features
CAUTION:
Read and follow all
Safety Rules and Operating Instructions
before first use of this product.
Customer
Help Line: 1-800-932-3188
Sears, Roebuck
and Co., Hoffman
Estates, IL 60179
Visit the Craftsman web page: www.sears.com/craftsman
972000.904
8-01
• Operation
• Maintenance
• Parts List
USA
®
10/03/01 WED 13:44
FAZ 864 964 3314 RYOBI CUSTOMER SERVICE
_003/O15
•
•
Warranty .......................................................................................................................................
Introductionand Product Specifications .........................................................................................................
III
Rules For Safe Operation ..........................................................................................................................
•
A. Important Safety Rules For Battery Tools ......................................................
B, Important Safety Instructions For Charger ....................................................................................
Accessories ...........................................................................................................................................
2
2
3-5
4
4
6
II
Features .....................................................................................................................................................
•
Operation ..............................................................................................................................................
II
Maintenance .................................................................................................................................................
13
•
•
Battery Pack Removal and Preparation For Recycling..........................................................................
Exploded View and Repair Parts List ....................................................................................................
13
15
FULL ONE YEAR WARRANTY
ON CRRFTSMRN
6
7-12
318 In. DRILL-DRIVER
If this I:RRFI"$MRN3/8 in. Drill-Driverfails to give complete satisfactionwithin one year from the date of purchase. RETURN IT TO THE NEAREST SEARS STORE OR SEARS SERVICE CENTER IN THE UNITED
STATES, and Sears will repair it, tree of charge.
If this CR#FI'$MRN3/8 in. Drill-Driveris used for commercial or remal purposes, this warranty applies for only 90
days from the date of purchase.
This warranty gives you specific legal rights,and you may also have other rights whichvary from state to state.
Sears, Roebuck
and Co., Dept, 817WA,
Hoffmsn
Estates, IL 60179
Your drill-driver has many features for making drilling
operations more pleasant and enjoyable. Safety,
performance and dependabl_y have been given top
priority in the design of this drill-drivermaking It easy
to maintain snd operate,
SPECIFICATIONS:
Chuck Capacity
Motor
Charger Rating
No Load Speed
Switch
Charge Rata
Pay close attention to the Rules For Safe
Operation, Warnings and Cautions. If you use
your drill-driverproperly and only for what it is
Intended, you will enjoy years of safe, reJiable
service.
Maximum Torque
2
3/8 in.
16.8 Volt DC
120 Volts, 60 Hz, AC Only
0 - 350 / 0 - 1300 RPM
Variable Speed - Reversible
10- 12 Hours
310 In./Ibs
10/03/01 WED 13:44
FAX 884 964 3314 RYOBI CUSTOMER SERVICE
The purpose of safety symbols Is to attract your attention to possible dangers. The safety symbols,
the explanations
with them, deserve your careful attention and understanding,
The safety warnings
not by themselves eliminate any danger, The Instructions or warnings they give are not substitutes
proper accident prevention measures.
SYMBOL
and
do
for
MEANING
A
SAFETY ALERT SYMBOL:
A
WARNING: Failure to obey a safety warningcan resultin serious injuryto yourself or to others.
Always follow the safety precautionsto reducethe risk of fire, electricshock and personal injury.
A
CAUTION: Failure to obey a safety warningmay result in propertydamage or personal injuryto
yourself or to others. Always follow the safety precautionsto reduce the risk of fire. electricshock
and personal injury.
NOTE:
Advisesyou of informationor insvucUonsvital to the operation or maintenance of the equipment.
indicates warning or caution. May be used in conjunctionwith othersymbols or pictographs.
USE RIGHT TOOL. Don't force small tool or
attachment to do the job of e heavy duty tool. Don't
use tool for purpose not intended - for example - A
circularsaw should never be used for cuffing tree
limbs or logs.
completely all InstruoUons,safety rules, etc.
contained in this manual. Failure to complycan
result in accidents involvingfirs, alectd¢ shock, or
serious personal injury. Save owner'smanual and
review frequentlyfor continuingsafe operation,
and instructingotherswho may use this tool,
WEAR PROPER APPAREL Do not wear loose
clothing or jewelry that can get caught in tool's
moving parts and cause personal injury. Rubber
gloves and nonskidfootwear are recommended
when workingoutdoors, Wear protective hair
coveringto contain long hair and keep it from being
drawn into nearby air vents.
READ ALL INSTRUCTIONS
KNOW YOUR POWER TOOL. Read owner's
manual carefully. Learn Its applicationsand
limitationsas well as the specific potential hazards
related to this tool.
•
[_004/015
GUARD AGAINST ELECTRICAL SHOCK by
preventing body contact with grounded surfaces.
For example: Pipes, radiators, ranges, refrlgerater
enclosures.
• ALWAYS WEAR SAFETY GLASSES, Everyday
eyeglasses have only impact-resistant lenses; they
are NOT safety glaSSes.
II PROTECT YOUR LUNGS. Wear s face mask or
dust mask if operation is dusty.
•
PROTECT YOUR HEARING. Wear headng
protectionduring extended padods of operation.
• AVOID DANGEROUS ENVIRONMENT, Don't use
power tool in damp or wet locations or expose to
rain. Keep work area well lit.
•
SECURE WORK, Use damps or a vise to hold
work. it's safer than using your hand and it frees
both hands to operate tool.
• KEEP CHILDREN AND VISITORS AWAY. All
visitors should wear safety glasses and be kept a
safe distance from work area. Do not let visitors
contact tool or extension cord.
•
DON'T OVERREACH.
Keep proper footing and
balance at all times. Do not use on a ladder or
unstable support.
•
MAINTAIN TOOLS WITH CARE. Keep tools sharp
at all times, and clean for best and safest performance, Follow instructionsfor lubricatingand
changing accessories.
•
REMOVE ADJUSTING KEYS AND WRENCHES.
Form habit of checking to see that keys and
adjusting wrenches are removed from tool before
turning it on.
•
KEEP WORK AREA CLEAN. Cluttered areasand
benches invite accidents.
II STORE IDLE TOOLS, When not in use tools
should be stored in a dry and high or locked-up
place - out of the reach of children.
•
DON'T FORCE TOOL, it willdo the job better and
safer at the rate for which it was designed.
10/03/01 WED 13:44
FAX 864 964 3314 RYOBI CUSTOMER SERVICE
RULES FOR SAFE OPERATION
(Continued)
NEVER USE IN AN EXPLOSIVE ATMOSPHERE.
Normal sparking of the motor could ignite flammable liquids, gases, or fumes.
II DO NOT PLACE BATTERY TOOLS OR THEIR
BATTERIES NEAR FIRE OR HE_.T. They may
explode.
II KEEP HANDLES DRY, CLEAN, AND FREE
FROM OIL AND GREASE. Always Use a clean
cloth when cleaning. Never use brake fluids,
gasoline, petroleum-based productsor any strong
solvents to clean yourtool.
•
_005/015
•
DO NOT CHARGE BATTERY TOOL IN A DAMP
OR WET LOCATION.
III Your battery tool should be charged in a location
where the temperature is more than 50°F but less
than 100°F,
STAY ALERT. Watch whet you are doing and use
common sense. Do not operate tool when you are
tired. Do not rush.
M Under extreme usage or temperature conditions,
battery leakage may occur. If liquidcomes in
contact with yourskin, wash immediately with
soap and water, then neutralize with lemon juice
or vinegar. If liquid gets in youreyes, flush them
with clean water for at least 10 minutes, then seek
immediate medical attantian.
M CHECK DAMAGED PARTS. Beforefurther use of
the tool, a guard or other part that Is damaged
should be carefully checked to determine that itwill
operate properly and perform its intendedfunction.
Check for alignment of moving parts, bindingof
moving parts, breakage of parts, mounting,and
any other conditionsthat may affect its operation.
A guard or other part that is damaged shouldbe
properly repaired or replaced by an authorized
service center unless indicated elsewhere in this
instructionmanual.
M If carryingyour battery tool at your side, make sure
it is not running and yourfinger is not on the
switch.Avoid accidental starting,
II SECURE WORK before applyingpower. NEVER
hold work,piece in your hand or across your legs.
•
DO NOT USE TOOL IF SWITCH DOES NOT
TURN IT ON AND OFF. Have defective switches
replaced by an authorized service center.
WHEN SERVICING USE ONLY IDENTICAL
CRAFTSMAN REPLACEMENT
PARTS.
IMPORTANT
CHARGER
DRUGS, ALCOHOL, MEDICATION. Do not
operate tool while under the influenceof drugs,
eTcehof,or any medication.
DRILLING OR DRIVING SCREWS INTO
ELECTRICAL
WIRING IN WALLS_ CEILINGS,
OR OTHER AREAS CAN CAUSE THE BIT OR
CHUCK TO BECOME ELECTRICALLY
LIVE. 0o
not touch metal parts when drilling; grasp only the
Insulmed handle(s) or plastic housing when using
this tool. Make sure hidden electrical wiring, water
pipes, and mechanical hazards are not in the path
of the bit when ddlling Into a wall.
SAFETY INSTRUCTIONS
FOR
•
SAVE THESE INSTRUCTIONS. This manual
contains importantsafety and operating
instructionsfor charger item number 9-11049
(1421410).
•
Before using battery charger, read all instructions
and cautionary markings In this manual, on battery
charger, and product using battery charger.
_WARNING;
To reduce dsk of injury,charge only
nickel-cadmiumtype rechargeabtebatteries. Other
types of batteries may burstcausing personal
injuryand damage,
[] INSPECT FOR and remove all nailsfrom lumber
before drilling.
[] Do not expose charger to rain or snow.
IMPORTANT
TOOLS
[] Use of an attachment not recommended or sold by
the battery charger manufacturer may result in a
risk of fire, electricshock, or injuryto persons.
•
SAFETY
RULES FOR BATTERY
Battery tools do not have to be plugged into an
electrical outlet: therefore, they are always in
operating condition. Be aware of possible hazards
when not using your battery tool or when changing
acoeesodes,
[] To reduce risk of damage to charger body and
cord, pull by plug body ratherthan cord when
disconnectingcharger.
•
USE ONLY THE CHARGER PROVIDED WITH
YOUR BATTERY TOOL. Do not substitute any
other charger. Use of another charger could cause
batteries to explode causing possible serious
injury.
4
Make sure cord Is located so that it will not be
stepped on, Idpped over, or otherwise subjected to
damage or stress.
10/03/01
_ED
13:45
RULES
•
FAX 864
964
3314
FOR SAFE OPERATION
RYOBI
¢UST0_[ER
_006/015
(Continued)
An extension cord should not be used unless
absolutely necessary. Use of improper extension
cord could result in a dsk of fire and electric shock.
If extension cord must be used. make sure:
a. That pins on plug of extension cord are the
same number, size and shape as those of plug
on charger.
b. That extension cord is propedy wired and in
good electrical condition:and
c. That wire size is large enough for AC ampere
rating of charger as specified below:
Cord Length {Feet) 25' 50' f00'
Cord Size (AWG) 16 16 16
Note: AWG = American Wire Gage
DO NOT OPERATE CHARGER WITH A
DAMAGED CORD OR PLUG, If damaged,
have replaced immediately by a qualified
serviceman.
•
SERVICE
•
Do not oPerate charger if it has received a sharp
blow. been dropped, or otherwise damaged in any
way,' take it to a qualified serviceman.
• Do not disassemble charger; take it to a qualified
serviceman when service or repair is required.
Incorrect reasaembly may result in a Hskof electric
shock or fire.
• Do not use charger outdoors.
• Disconnect charger from power supply when not in
_Jse.
• SAVE THESE INSTRUCTIONS. Refer to them
frequently and use them to Instructothers who may
use this tool. If you loan someone this tool, loan
them these instructionsalso.
A, WARNING: Some dust created by power
sanding, sawing, grinding, drilling,and other
constructionactivitiescontains chemicals knownto
cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are;
• lead from lead-based paints,
• crystaltitesilicafrom bricksand cement
and other masenw products, and
• arsenic and chromiumfrom chemicallytreated lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designedto tilterout microscopic
particles.
• To reduce dsk of electric shock, unplug charger
from outlet before attempting any maintenance or
cleaning. Turning off Controlswillnot reduce this
risk.
_k
Look for this symbol to point out important safety precautions.
safety is involved.
It means attentionlll
Your
WARNING:
The operation of any power tool can result in foreign objectsbeing thrown into your eyes,
which can result in severe eye damage. Before beginning power tool operation, always
wear safety goggles or safety glasses with side shields and a full face shield when needed.
We recommend Wide Vision Safety Mask for use over eyeglasses or standard safety
glasses with side shields,available at Sears Retail Stores.
10/03/01 WED 13:45
FAX 864 964 3314 RYOBI CUSTOMER SERVICE
[_007/O15
The following recommended accessories are currently available at Sears Retail Stores.
•
6-Pc. Extra Length Magnits Power Bit Set
II
High Speed Bits (FOrWood or Metal)..3/4 in. Max.
II
30-Pc. Power Screwddver/NutddverSet and Case
•
Keyless Chuck (Item No, _-20988)
II
17-Pc. Power Screwdriver/NutdriverSet and Case
A
WARNING:
The use of attachments or accessories not listedmight be hazardous.
KNOW YOUR DRILL-DRIVER
See F_um I.
Before attempting to use any tool familiarize yourself
with all operating features and safety requirements,
_
WRIST STRAP
See Fi#um 1,
A wdst strap is provided to reduce the chances of
droppingyou="ddlFdriver.Place one hand through the
wrist strap when carryingtool,
"I_/O-$PEED
GEAR TRAIN(RFLO)
SCREWDPJVERBITS
BITSTORAGE
LEVEL
KEYLESS
CHUCK
BATTERYPACK
BATTERY
CHARGER
ROTATION
SELECTOR
\
SWITCH
TRIGGER
RED
UGHT
WRISTSTRAP
Fig. 1
socouresultWARNIIdNG:If
WIposslb/sserious
anYpatts
are misslng'rd°nrl°tn°POrate
pe so al i jurY_
tool Urlfilthe missing parts are repJaced. FalJure to do
6
10/O3/O1
WED
13:45
FAX
864
964
3314
RYOBI
CUSTOMER
SERVICE
•
tools. Failure to do so could resultin objects
being thrown into your eyes, resulting in possible
serious injury.
&
o
a careless fraction of a second is sufficientto
inflict severe injury.
CHARGING
BA'I-FERY PACK
The battery pack for this tool has been shippedIn a
low charge conditionto prevent possible problems.
Therefore, you should charge It overnightpriorto use.
Note: Batteries will not reach full charge the first time
they ere charged. Allow several cycles (drilling
followed by recharging) for them to become fully
charged.
TO CHARGE
•
Charge battery pack only with the charger and
charging stand provided.
•
Make sure power supply is normal
voltage, 120 volts, 80 Hz, AC only.
•
Connect charger to power supply.
house
[_008/015
Place battery pack in charging stand. Align raised
rib on battery pack with groove in charging stand.
See Figure 1.
• Press clownon battery pack to be sure contacts on
battery pack engage properly with contacts in
charging stand.
• When properly cOnnected,the red light on charging
stand will turn on.
•
•
Note: ff cha_:jer does not chargebatterypeck, return
batterypack, chargerand chargingstand to your
nearest Sears RepoJrCenter for electrioalcheck,
After normal usage, a minimum charge time of 10
hours Is required to recharge a completely
discharged tool.
• The battery pack will become slightly warm to the
touch while charging.This is normal and does not
indicate a problem.
•
Do not place charger In an ares of eXtreme heat or
cold, It will work best at normal room temperature.
• When batteries become fully charged, unplug
charger from power supply.
to/03io1 WED 13:45
FAX 864 964 3314 RYOBI OUSTO_R
SERVICE
TO INSTALL
SWITCH
See Figure 2.
To turn your ddll ON. depress the switchtrigger. To
turn it OFF, release the switchtrigger.
•
_oo9/o15
BATTERY PACK
Lock switoh tdgger on your drill byplacing the
directionof rotationselector in center position.
See Fi#um 5.
Place battery pack in your drill. Alignraised rib
inside drill with groove on battery pack.
Sos Figure 4.
•
SELECTOR
Fig. 2
BAITERY PACK
VARIABLE
SPEED
This tool has a variable speed switchthatdelivers higher
speed and torquewith increasedtriggerpressure.Speed
iscontrolledby the amount of switch triggerdepression.
Note: You might hear e whistlingor ringingnolse from
the switch during use. Do not be concerned, this is a
normal part of the switch function.
LATCHES
TWO-SPEED
GEAR TRAIN
See F_gure 3.
Your drill has a two-speed gear train designed for
drilUng or driving at HI or LO speeds. A slide switch is
located on top of your drill to select either HI or LO
speed. When using drill in the HI speed range, speed
will increase end unit will have less power and torque.
When using drill In the LO speed range, speed will
decrease and unit will have more power and torque.
Use HI speed for fast ddlling or driving applications
and LO speed for high power and torque applications.
LOSPEED
HI SPEED _
DEPRESSLATCHESTO
RELEASEBAI"rERYPACK
Fig, 4
[] Make sure the latches on each side of your battery
pack snap in place and battery pack is secured in
ddll before beginning operation.
When placing battery pack in
_IL drill,CAUTION:
sure raised rib inside ddll aligns with
y°Urbe
TWOSPEED
GEARTRAIN(HI-I.O)
groove on battery pack and latches snap into
plaoe properly. Improper assembly of battery
pack can cause damage to internalcomponents.
TO REMOVE BAI"TERY PACK
•
•
[]
Fig. 3
8
Lock switch trigger on your ddll by placing the
direction of rotation selector in center position.
See Figure 5.
Locate latches on end of battery pack and depress
to release battery pack from your ddll,
See F_Jm 4.
Remove battery pack from your drill.
10/03/01 WED 13:46
FAX 884 084 3314 RYOBI CUST0_ER SERVICE
_010/015
SWITCH LOCK
See Figure 5..
KEYLESS CHUCK
The switch trigger can be locked In the OFF position.
This feature can be used to prevent the poasibNityof
accidental sta_lng when not in use. To lock switch
trigger, place the direction of rotation selector in
center position.
Yourdrillhas a keylasschuck.ASthe name implies,you
can handtightenor release drillbitsin the chuckjaws.
Grasp and holdthe collarof the chuckwith one hand.
Rotate the chuckbodywithyour otherhand. The arrows
on the chuckindicatewhichdirectionto rotate the chuck.
bodyin orderto LOCK (tighten)or UNLOCK (release)
the drillbit.
See Figure 6.
CENTERPOSITION
(LOCK)
FORWARD
UNLOCK
(RELEASE)
REVERSE
SELECTOR
SWffCH
TRIGGER
DRILLBIT
LOCK
Fig. 5
A
WARNING: Bs=eP/tools are always in
operating condition. Therefore, switch should
always be locked when not in use or carryingat
your side.
(TIGHTEN)CHUCK COLLAR
Fig, 6
REVERSIBLE
See Figure 5.
This tool has the feature of being reversible. The
direction of rotationIs controlledby a selector located
above the switch trigger. With the drill held In normal
operating position,the direction of rotation selector
should be positionedto the left ot the switch for
drilling.The drilling direction is reversed when the
selector is to the right of the switch, When the selector
Is In center position,the switch trigger is locked,
changing the direction of rotation or the twospeed gear train (hi-lo).
To stop. release switch trigger and allow the chuck to
come to a complete stop.
A
not hold chuck body with one
WARNING:hand
and useDO
power of the drill to tighten chuck
jaws on drill bits.Chuck body could slip in your
hand or your hand could slip and come In contact
with rotatingdrill bit.This could cause an
accident resultingin serious personalin}ury.
10103101 WED 13:46
FAX 864 964 3314 RYOBI CUSTOMER SERVICE
INSTALLING BITS
See FTgure7..
•
Lock the switch triggerby placingthe directionof
rotation selector in center position.See Figure 5.
•
•
•
Open or close chuck jaws to a pointwhere the
opening is slightly larger than the bit size you
Intend to use. Also, raise the front of your drill
slightly to keep the bit from faiUngout of the chuck
Jaws.
Insert drill bit straight Into chuck the full length of
the jaws as shown in Figure 7.
Tighten the chuck jaws on drillbit.
CHUCKJAWS
REMOVING
BITS
See Fi#ure Z
•
•
II
Lock the switch trigger by placingthe directionof
rotationselector in center position.See F/gur_ 5.
Loosenthe chuckjaws from drillbit.
To loosen:grasp and hold the collar of the chuck
with one hand, while rotatingchuck body with your
other hand. Note: Rotate chuck body in the
directionof the arrow marked UNLOCK to loosen
chuck
Jaws.
11 Do not use a wrench to tighten or loosen the
chuck jaws.
II
CHUCKBODY
[_011/015
Remove drillbit frem chuck jaws.
ADJUSTABLE
TORQUE
CLUTCH
Your ddll is equipped with an adjustable torque oJutoh
for driving different types of sorews intodifferent matedais. The proper settingdepends on the type of matedal and the size of screw you are using,
TO ADJUST TORQUE
•
DRILL BIT
•
CHUCKCOLLAR
PJGHT
Fig. 7
IN To tighten the chuck Jawson drillbit; grasp and
hold the collar of the chuck with one hand, while
rotating the chuck body with your other hand.
•
Note= Rotate the chuck body in the directionof
the arrow marked LOCK to tighten chuck jaws,
Do not use a wrench to tighten or loosenthe
chuck jaws.
Identify the twenty four torque indicator settings
locatedon the front of your drill. See Figure 9.
Rotate adjusting ring to the desired setting,
• 1- 4
For driving small screws.
•
5 -8
• 9 - 12
• 13 - 16
For driving screws into soft
material.
For driving screws intosoft and hard
materials.
For driving screws in hard wood.
• 17 - 20 For ddving large screws.
• 21 - 4,_1,¶For heavy drill(rig.
TO DECREASE
TORQUE
jaws at an angle then tighten as shown in Figure
8, This could cause drillbit tO be thrownfrom ddn.
resulting In possibleserious personalinjuryor
damage to the chuck.
_LDJUSTING
RING
TOINCREASE
TORQUE
10/03/01 WED 13:46
FAX 864 964 3314 RYOBI CUSTOMER SERVICE
Note: Remember the two-speed feature (RI-LO) when
setting torque. The amount of torque will vary depending on which speed se_ng you have yourdrill-driver,
Switchingto LO speed willincrease torque. Switching
to HI speed witl decrease torque.
[_012/015
DRILLING
See Figure 12.
BIT STORAGE
See F/_ute TO,
When not In use, bits provided with yourdrill can be
placed in the storage area located on the top of your
drill as shown In Figure 10.
BITSTORAGEAREA
Fig. 10
Fig. 12
When drillinghard smooth surfaces use a center
punch to mark desired hole location. This will prevent
the drillbit fi'omslippingoff center as the hole is
started, However, the low speed feature allows
starting holes withoutcenter punchingif desired. To
accomplishthis. simplyoperate yourdrill at a low
speed until the hole is started.
The material to be drilled should be secured In a vise
or with clamps to keep it from turning as the drill bit
rotates.
tools. Failure to do so could result In objects
being thrown intoyour eyes, resulting in possible
sedous injury.
LEVEL DRILLING
See l_Igute
lf.
A convenient new feature prevlded with your drill is a
level. It ts recessed in the motor housingon top of
your drill. It can be used to keep drill bits level during
drilling operations.
Hold tool firmly and place the bit at the point to be
drilled. Depress the switch trigger to start tool
Move the drill bit into the workpiece applying only
enough pressure to k_eepthe bit cuffing. Do not force
or apply side pressure to elongate a hole.
lEVEL
_lk
bre_<through.WhenWARNING:
Be prepared
forthes
e situations
bindingor
occur,
bit drill
has a tendency to grab and kick oppositeto the
directionof rotationand could cause loss of
controlwhen breaking through material. If not
prepared, this loss of cOntrolcan result in
possibleserious Injury.
When drilling metals, use a light oil on the drill bit to
keep it from overheating. The oil wiff prolong the life of
the bit and increase the drilling action,
If the bit Jams in workplace or if the drill stalls, release
switch trigger immediately, Remove the bit from the
workpiece end determine the reason for jamming.
Fig. 11
11
10/03!01
WED 13:47
FAX 864
964
3314
RYOBI CUSTOMER SERVICE
CHUCK REMOVAL
Gee Figures f3, 14, and 15.
Insert hex key wrench in chuck and tighten chuck
jaws securely. Tap sharply with a mallet in a
counterclockwise direction. This will loosen chuck
on the spindle, It can now be unscrewed by hand.
,.SeeF_gure 15.
The chuck must be removed in order to use some
accessories, To remove:
II Lock the switch trigger by placing the directionof
rotationselector,in center position. See F/gum 5.
El Inserta 5/16 Inch or larger hex key wrenchintothe
chuck of yourdrilland tightenthe chuck jaws
securely.
•
[_013/015
Tap the hex key wrench sharply with a mallet in a
clockwisedirection. See F/gut's 13.This will
loosen the screw in the chuck for easy removal.
MALLET
KEYLESSCHUCK
Fig. 15
TO RETIGHTEN
A LOOSE CHUCK
The chuck may become loose on sp]ndla and develop
wobble. Periodicallycheck chuck screw for tighthess,
CHUCK,JAWS
•
HEXKEY
WRENGH
To tighten, follow these steps:
•
Lock the switch triggerby placing the direction of
rotationselector in center position, See F/gure 5.
II O_en the chuck jaws.
Fig. 13
Open chuck jaws and remove wrench. Remove
the chuck screw by turning It in a olockwise
direction. See F/gu,_a11,
Note: The screw has left harld threads.
•
•
II
Fig. 14
12
Inserthex key wrenchinto chuck and tighten
chuckJaws securely. Tap hex key wrench sharply
with a mallet in a clookwise direction.This will
tightenchuck on the spindle.
Open the chuck jaws and remove hex key
wrenoh.
Tighten the chuck screw.
Note: The chuck screw has left hand threads.
10103/01
WED 13:47
FAX 864
964
.3314
RYOBI
CUSTOMER SERVICE
[_]014/015
Do not abuse power tools. Abusive practices can
damage tool as well as Well,Oleos.
part may create a hazard or cause product
damage.
Only the parts shown on parts list, page 15, are
intended to be repaired or replaced by the customer.
All other parts shouldbe replaced by a Sears Service
Center.
Avoid using solvents when cleaningplastic
parts.
Most plastice are susceptibleto damage from various
types of commercial solvents and may be damaged
by their use. Use clean cloths to remove dirt, dust. oil,
grease, etc.
_k. cWr
_tReN/NeG_
sD° an:tn_tt;2c_Ptrot°emn
dc_did
fyftOhi_
Jts_OI
or
with this tool. Any such alteration or modification
is misuse and could result in a hazardous
conditionleading to possible serious personal
injury.
oils, etc. come in contact with plasticpads. They
contain chemicals that can damage, weaken or
destroy plastic.
BATTERIES
Your'drill's battery pack is equipped with 14 nickelcadmium rechargeable batteries. Length of service
from each charging willdepend on the type of work
you are doing.
The batteries in this tool have been designed to
provide maximum trouble free life. However. like all
batteries, they will eventually wear out. De not
disassemble battery pack and attempt to replace the
batteries. Handling of these batteries, espedally when
wearing rings and Jewelry,could result in _.serious
burn.
II
[]
[]
To obtain the longest possible battery llte, we suggest
the following:
Store and charge your batteries in a cool ares.
Temperatures above normal room temperature
will shorten battery life.
Never store batteries in a discharged condition.
Recharge them Immediately after they are
discharged.
All batteries gradually 10setheir charge. The
higherthe temperature the quicker they lose their
charge. If you store your tool for long perleds of
time withoutusing it, recharge the batteries every
month or two. This practicewill prolongbattery
lile.
BA'I-rERY PACK REMOVAL AND
PREPARATION FOR RECYCLING
To preservenatural resources, please
recycleor disposeof batteries
properly.
This productcontains nickelcadmium batteries. Local, state or
federal laws may prohibitdisposalof
nickel-cadmium batteries In ordinary
trash.
Do hot attempt to destroy or disassemble battery
pack or remove any of its components. Nickelcadmium batteries mustbe recycled or disposed
of properly.Also, never touch both terminals with
metal objectsand/or body parts as short c_rcuit
may result. Keep away from children. Failure to
comply with these warnings could result in fire
and/or serious injury.
Consult your local waste authority for information
regarding available recycling and/or disposal options.
13
10/03/01
WED 13:47
.----
FAX 864
CRAFTSMAN
964
3314
RYOBI CUSTOMER SERVICE
3/8 In,, 16.8 VOLT CORDLESS
_015/015
DRILL-DRIVER-
MODEL NO, 973.111430
number in ell correspondence regarding your 3/8 in., 16.8 VOLT CORDLESS DRILL=DRIVER or
The model number will be found on a plate attached to the motor housing. Always mention the model
when ordering repair parts.
,.,
SEE BACK PAGE FOR PARTS ORDERING
INSTRUCTIONS
2
\
1
4
3
PARTS LIST
Key
No.
Part
Number
Description
1
616478-003
Screw (Special) .................................................................
1
2
973015-001
Chuck (Item No, _20988)
.................................................
1
....................................................
1
Quan,
3
" Item No. 9-11048
Battery Pack (1311436)
4
* Item No. _-11049
Charger w/Cha_ling
Stand (1421410)
..............................
1
5
3O51791
Carrying Case - Not Shown .............................................
1
6
982113-001
Tool Bag - Not Shown ......................................................
Owner's Manual
1
972000-904
n
i
" Can Be Purchased
Thru RSOS (Retail Special Order System)
15
i
_-