Canon LV-5110U Specifications

CONTENTS
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
fi-5110C Image Scanner Operator's Guide
P3PC-1082-01EN
CONTENTS
INTRODUCTION
Regulatory Information
Introduction
Thank you for purchasing the fi-5110C duplex color scanner.
This document describes how to handle fi-5110C Duplex Color scanner and basic operation methods.
Before you start using fi-5110C Duplex Color scanner, be sure to thoroughly read this manual to ensure
the correct use.
Contents Map
Trademarks
Note, Liability
Preface
Safety Precautions
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
●
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
●
9 SCANNER SPECIFICATIONS
●
Appendix
Copying of the contents of this manual in whole or in part and copying of the
scanner application is forbidden under the copyright law.
The contents of this manual are subject to change without notice.
PFU LIMITED. is not liable whatsoever for any damages resulting from use of
this scanner and procedures described in this manual, profit due to defects, and
any claims by a third party.
CONTENTS
Regulatory Information
1
INTRODUCTION
2
3
FCC Declaration
Regulatory Information
Trademarks
Note, Liability
Preface
Safety Precautions
1 NAMES AND FUNCTIONS OF PARTS
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
2 BASIC SCANNER OPERATIONS
●
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
●
●
●
4 DAILY CARE
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is located.
Consult your dealer or an experienced radio/TV technician.
5 REPLACING CONSUMABLES
FCC warning:
6 TROUBLESHOOTING
Changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
ATTENTION
Appendix
The use of a shielded interface cable is required to comply with the Class B
limits of Part 15 of FCC rules. The length of the AC cable must be 2 meters
(6.6 feet) or less.
1
2
3
CONTENTS
Regulatory Information(2)
1
INTRODUCTION
2
3
Canadian DOC Regulations
Regulatory Information
Trademarks
Note, Liability
Preface
Safety Precautions
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
This digital apparatus does not exceed the Class B limit for radio noise emissions from digital
apparatus set out in the Radio interference Regulations of the Canadian Department of
Communications.
This Class B digital apparatus complies with Canadian ICES-003.
Le pésent appareil numérique n'ément pas de bruits radioélectriques dépaassant les limites
applicables aux appareils numériques de la classe B prescridtes dans le Réglesment sur le
brouillage radioélectrique dicté par le ministere des Communications du Canada.
Cet appareil numérique de la classe B est conformme á la norme NMB-003 du Canada.
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
Bescheinigung des Herstellers / Importeurs
4 DAILY CARE
Hiermit wird bescheinigt, daß der/die/das fi-5110C
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
●
●
In Übereinsstimmung mit den Bestimmungen der EN45014 (CE) funkentstört ist.
Laut Maschinenlärminformationsverordnung 3. GS GV, 18.01.1991: Der höchste
Schalldruckpegel beträgt 70 dB (A) oder weniger gemäß ISO/7779.
International ENERGY STAR® Program
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
As an ENERGY STAR® Partner, PFU LIMITED has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
The International ENERGY STAR® Office Equipment Program is an international program
that promotes energy saving through the penetration of energy efficient computers and other
office equipment. The program backs the development and dissemination of products with
functions that effectively reduce energy consumption. It is an open system in which business
proprietors can participate voluntarily. The targeted products are office equipment such as
computers, monitors, printers, facsimiles, copiers, scanners, and multifunction devices. Their
standards and logos (
) are uniform among participating nations.
1
2
3
CONTENTS
Regulatory Information(3)
1
INTRODUCTION
2
3
Use in High-safety Applications
Regulatory Information
Trademarks
Note, Liability
Preface
Safety Precautions
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
This product has been designed and manufactured on the assumption that it will be used in
office, personal, domestic, regular industrial, and general-purpose applications. It has not
been designed and manufactured for use in applications (simply called "high-safety
applications" from here on) that directly involve danger to life and health when a high degree
of safety is required, for example, in the control of nuclear reactions at nuclear power
facilities, automatic flight control of aircraft, air traffic control, operation control in masstransport systems, medical equipment for sustaining life, and missile firing control in weapons
systems, and when provisionally the safety in question is not ensured. The user should use
this product with adopting measures for ensuring safety in such high-safety applications. PFU
LIMITED assumes no liability whatsoever for damages arising from use of this product by the
user in high-safety applications, and for any claims or compensation for damages by the user
or a third party.
4 DAILY CARE
About the Use of Mercury
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
Lamp(s) inside this product contain mercury and must be recycled or
disposed of according to local, state, or federal laws.
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
To avoid unexpected injury, read the following carefully.
Doing the following actions may result in serious personal injuries:
●
●
●
Do not put the substance contained in the lamp in your mouth as it has mercury.
Do not incinerate, crush, or shred the lamps or scanner parts.
Do not breathe the chemical liquid contained in the scanner lamps.
1 | 2 | 3
CONTENTS
Trademarks
1
2
Trademarks
INTRODUCTION
Regulatory Information
Trademarks
Note, Liability
Preface
Safety Precautions
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation in the
United States and/or other countries.
ISIS, QuickScan and their respective logos are trademarks or registered trademarks of Pixel
Translations, a division of Captiva Software Corporation in the United States.
Adobe, the Adobe logo, and Acrobat are either registered trademarks of Adobe Systems
Incorporated in the United States and/or other countries.
Other product names are the trademarks or registered trademarks of the respective companies.
How Trademarks Are Indicated In This Manual
References to operating systems (OS) and applications are indicated as follows
Windows 95
Microsoft® Windows® 95 operating system
Windows 98
Microsoft® Windows® 98 operating system
Windows Me
Microsoft® Windows® Millennium Edition operating system
Windows NT 4.0
Microsoft® WindowsNT® Server operating system Version4.0
Microsoft® WindowsNT® Workstation operating system Version4.0
Windows 2000
Microsoft® Windows® 2000 Professional operating system
Windows XP
Microsoft® Windows® XP Professional operating system
Microsoft® Windows® XP Home Edition operating system
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
Where there is no distinction between the different versions of the above operating system, the
general term "Windows" is used.
Adobe Acrobat 6.0
Adobe® Acrobat® 6.0 standard
1
2
CONTENTS
Trademarks(2)
1
2
Manufacturer
INTRODUCTION
PFU LIMITED
Regulatory Information
Trademarks
Note, Liability
International Sales Dept., Imaging Bussines Division, Products Group Solid Square East Tower,
580 Horikawa-cho, Saiwai-ku, Kawasaki-shi Kanagawa 212-8563, Japan
Phone: (81-44) 540-4538
Preface
Safety Precautions
All Rights Reserved, Copyright(C) PFU LIMITED 2004
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
1
2
CONTENTS
Note, Liability
BEFORE USING THIS PRODUCT, PLEASE READ THIS MANUAL CAREFULLY. IF THIS PRODUCT IS
NOT USED CORRECTLY, UNEXPECTED INJURY CAN OCCUR TO USERS OR BYSTANDERS
Keep this manual in a safe place so that it can be easily referred to during use of this product.
INTRODUCTION
Regulatory Information
Trademarks
Note, Liability
Preface
Safety Precautions
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
While all efforts have been made to ensure the accuracy of all information in this manual, PFU assumes
no liability to any party for any damage caused by errors or omissions or by statements of any kind in this
manual, its updates or supplements, whether such errors are omissions or statements resulting from
negligence, accidents, or any other cause. PFU further assumes no liability arising from the application or
use of any product or system described herein; nor any liability for incidental or consequential damages
arising from the use of this manual. PFU disclaims all warranties regarding the information contained
herein, whether expressed, implied, or statutory.
CONTENTS
Preface
1
2
3
Safety Precautions
INTRODUCTION
Trademarks
This manual describes important details for ensuring the safe and correct use of this product.
Thoroughly read this manual before you start to use this product. In particular, be sure to read and
fully understand the Safety Precautions described in this manual before you use this product.
Note, Liability
Also, store this manual in a safe place so that it can be easily referred to during use of this product.
Regulatory Information
Preface
Safety Precautions
1 NAMES AND FUNCTIONS OF PARTS
Warning Indications Used In This Manual
This manual uses the following indications to ensure safe and correct use of this product, and to
prevent possible danger and injury to the operator and other persons.
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
Warning
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
This indication alerts operators to an operation that, if not strictly
observed, may result in severe injury or death.
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
Caution
This indication alerts operators to an operation that, if not strictly
observed, may result in safety hazards to personnel or damage to
equipment.
1
2
3
CONTENTS
Preface(2)
1
2
3
Symbols Used In This Manual
INTRODUCTION
Regulatory Information
This manual uses the following symbols in the explanations in addition to the warning
indications.
Trademarks
Note, Liability
This symbol alerts operators to particularly important information. Be sure to read this
information.
Preface
This symbol alerts operators to helpful advice regarding operation.
Safety Precautions
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
A TRIANGLE symbol indicates that special care and attention is required. The drawing inside
the triangle shows the specific caution.
A CIRCLE with a diagonal line inside shows action which users may not perform.
The drawing inside or under the circle shows the specific action that is not allowed.
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
Outline characters on a colored background show instructions users should follow.
It may also include the drawing that shows the specific instruction.
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
Clicking in this icon will play a movie.
9 SCANNER SPECIFICATIONS
Appendix
1
2
3
CONTENTS
Preface(3)
1
2
3
Screen Examples In This Manual
INTRODUCTION
Regulatory Information
Trademarks
Note, Liability
Preface
The screen examples in this manual are subject to change without notice in the interest of product
improvement. If the actual displayed screen differs from the screen examples in this manual,
operate by following the actual displayed screen while referring to the User's Manual of the scanner
application you are using. The screenshots in this manual were captured from the FUJITSU
TWAIN32 scanner driver, ScandAll 21 Image Capturing Utility Software, FUJITSU ISIS scanner
driver, QuickScanTM image capturing software and Adobe® Acrobat®.
Safety Precautions
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
Warning Label
The following picture shows the warning label used in this scanner.
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
High Temperature
The glass surface inside
the ADF becomes hot
during the operation.
Be careful not to touch
the glass surface inside
the ADF.
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
ATTENTION
Do not remove from the scanner, stain or scratch the warning labels.
About Maintenance
The user must not perform repairs on this scanner.
Contact the store where you purchased the scanner or an authorized FUJITSU Image Scanner
service provider to have repairs done on this product.
1
2
3
CONTENTS
Safety Precautions
1
2
3
4
INTRODUCTION
Regulatory Information
WARNING
Trademarks
Note, Liability
Preface
The following are the important warnings described in this manual.
Safety Precautions
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
Do not damage the AC cable.
A damaged AC cable may cause fire or electric shock. Do not place heavy
objects on AC cables, or pull, bend, twist, heat, damage or modify AC
cables.
Do not use damaged AC cables or power plugs, or install any cables or
power plugs to loose wall sockets.
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
Use only specified AC cables and connector cables.
9 SCANNER SPECIFICATIONS
Appendix
Use only specified AC cables and connector cables. Failure to use the correct
cables might cause electric shock and/or equipment failure.
Use this scanner only at the indicated power voltage.
Do not connect to multiple-power strips.
Use this scanner only at the indicated power voltage and current. Improper
power voltage and current might cause fire or electric shock. Do not connect to
multiple-power strips.
Do not touch the AC cable with wet hands.
Do not touch the power plug with wet hands. Doing so can cause electric shock.
Wipe any dust from the power plug.
Wipe off any dust from metal parts on the power plug or metal fittings with a soft,
dry cloth. Accumulated dust can cause fire or electric shock.
1
2
3
4
CONTENTS
Safety Precautions(2)
1
2
3
4
INTRODUCTION
Regulatory Information
Trademarks
Note, Liability
Do not install the scanner in locations subject to oil smoke,
steam, humidity, and dust.
Preface
Safety Precautions
1 NAMES AND FUNCTIONS OF PARTS
Do not install the scanner in locations subject to oil smoke, steam, humidity, and
dust. Doing so might cause a fire or electric shock.
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
Turn the scanner OFF if it is damaged.
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
If the scanner is damaged for any reason, turn the scanner off and unplug the
power cable. Contact the store where you purchased the scanner.
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Do not put liquids inside the scanner.
Appendix
Do not insert or drop metal objects in to the scanner. Do not scan wet
documents or documents with paper clips or staples. Do not splash or allow the
scanner to get wet.
If foreign objects (water, small metal objects, liquids, etc.) get inside the
scanner, immediately turn off the scanner and disconnect the power plug from
the power outlet. Then, contact the store where you bought the scanner or the
Maintenance Service Center. Pay particular attention to this warning in
households where there are small children.
Do not touch the inside of the scanner unless necessary.
Do not take apart or modify the scanner. The inside of the scanner contains highvoltage components. Touching these components might cause electric shock or
fire.
Do not use the scanner if there is a strange odor.
If you detect heat coming from the device or detect other problems such as
smoke, strange smells or noises, immediately turn off the scanner and
disconnect its power plug. Make sure that any smoke coming from it has
stopped, before contacting the store where you bought the scanner or an
authorized FUJITSU scanner service provider.
1
2
3
4
CONTENTS
Safety Precautions(3)
1
2
3
4
INTRODUCTION
Regulatory Information
CAUTION
Trademarks
Note, Liability
Preface
The following are the important cautions described in this manual.
Safety Precautions
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
Do not install the scanner on unstable surfaces.
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
Make sure that the scanner is installed on a flat, level surface and that none of
its parts extend beyond the surface top, such as a desk or table. Do not install
the scanner on unstable surfaces. Install the scanner on a level surface that is
free of vibration to prevent it from falling.
Install the scanner on a strong surface that will support the weight of the scanner
and other devices.
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Do not block the ventilation ports.
Appendix
Do not block the ventilation ports. Blocking the ventilation ports generates heat
inside of scanner, which may result in fire or scanner failure.
Do not place heavy objects or stand on top of the scanner.
Do not place heavy objects on the scanner or use the scanner's surface top to
perform other work. Improper installation might cause injuries and equipment
failure.
Firmly insert the power plug.
Firmly insert the power plug as far it can go into the power outlet.
Avoid any contact when scanner is in use.
Avoid touching any scanner mechanism during scanning since this may cause
injuries.
Do not use the scanner immediately after moving it from a
cold place into a warm room.
Do not use the device immediately after moving it from a cold place into a warm
room. Condensation may occur, which might lead to scanning errors. Let the
device dry about one or two hours before you use it.
1
2
3
4
CONTENTS
Safety Precautions(4)
1
INTRODUCTION
Regulatory Information
Trademarks
Note, Liability
Preface
Safety Precautions
1 NAMES AND FUNCTIONS OF PARTS
2
3
4
Before moving the scanner, disconnect the power plug from
the power outlet.
Do not move the scanner with the power and interface cables connected as this
can damage the cables, which can later cause fire, electric shock as well as
injury.
Before moving the scanner, be sure to disconnect the power plug from the
power outlet, and all other data cables. Make sure that the floor is free of any
obstructions.
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
Protect the scanner from static electricity.
Install the scanner away from strong magnetic fields and other sources of
electronic noise. Also, protect the scanner against any static electricity, which
can cause the scanner to malfunction.
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
Do not use aerosol sprays near the scanner.
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
Do not use aerosol sprays to clean the scanner. Aerosol sprays can blow dirt
and dust inside the scanner, resulting in scanner failure or malfunction.
Disconnect the power plug from the power outlet when the
scanner is not used for a long period of time.
When the scanner is not going to be used for a long period of time, be sure to
disconnect the power plug from the power outlet.
Do not install the scanner in direct sunlight.
Do not install the scanner under direct sunlight or near heating apparatus. Doing
so might cause excessive heat to build up inside the scanner, which can cause
scanner trouble or even fire. Install the scanner in a well-ventilated location.
1
2
3
4
CONTENTS
1 NAMES AND FUNCTIONS OF PARTS
This chapter describes names and functions of parts.
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
1.1 Names and functions of parts
1.2 Functions of the operator panel
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
CONTENTS
1.1 Names and functions of parts
1
2
3
Front view
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
1.1 Names and functions of parts
1.2 Functions of the operator panel
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
No.
1
2
3
4
5
6
Name
Function
Automatic document feeder(ADF)
It transports the document to the reading position
automatically.
ADF paper chute
Holds in place the document pages / sheets that are fed
into the ADF.
Side guide
It is adjusted to the width of the paper in order not to scan
skewed pages.
ADF open lever
Pull this lever to open the ADF.
Operator panel
This panel consists of a Function No. display, four
operating push buttons and a LED.
Stacker
Scanned documents are ejected from the ADF onto this
tray.
1
2
3
CONTENTS
1.1 Names and functions of parts(2)
1
2
3
Rear view
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
1.1 Names and functions of parts
1.2 Functions of the operator panel
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
No.
Name
Function
7
USB Interface connector
Used for connecting a USB interface cable from a PC.
8
DC inlet
Used for connecting the AC cable from the power outlet.
9
Security Cable Slot
Used for connecting the security cable.
1
2
3
CONTENTS
1.1 Names and functions of parts(3)
1
2
3
Removable Parts
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
1.1 Names and functions of parts
1.2 Functions of the operator panel
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
No.
Name
10
Pad ASSY
11
Sheet guide
12
ADF paper chute
13
Pick roller
1
2
3
CONTENTS
1.2 Functions of the operator panel
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
1.1 Names and functions of parts
1.2 Functions of the operator panel
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
No.
Name
Function
1
Function No. display
Indicates the function No. and error status.
2
Function button
Changes the Function activated by the Send to button.
3
Send to button
Launches the linked application software.
4
Scan button
5
Power button
Turns the scanner ON and OFF.
6
LED
Lights when the scanner is turned ON.
Indications on the Function Number display
Indication
Meaning
8
Blinks only one time upon turning on the scanner.
P
Indicates that the scanner has been turned ON and is being initialized.
0
Indicates that initialization will soon end.
1
Indicates that initialization has ended successfully.
The scanner is now in "Ready Status".
U
Indicates that a temporary error occurred when documents were being scanned. A number
appearing in alternation following the U (i.e. 1, 2 and 4) refers to the type of error.
To return the scanner to the ready status ("1"), press "Scan" or "Send to" button.
E
Indicates that a device (hardware) alarm has occurred during scanning of documents.
"E" and the alarm Number (2 to 9 and c ) will appear alternately.
To return the scanner to the ready status ("1"), press "Scan" or "Send to" button.
If this alarm occurs, turn the power off and on again. If the alarm continues after turning the
power on again, contact your service engineer.
CONTENTS
2 BASIC SCANNER OPERATION
This chapter describes basic scanner operations.
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
2.1 Turning the scanner ON
2.2 Loading Documents on the ADF for
Scanning
2.3 Scanning Documents
2.4 How to Use the Scanner Driver
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
In this chapter Windows XP screenshots are illustrated.
The screens and operations may differ slightly if the OS that you are using is other than Windows XP.
Also, when FUJITSU TWAIN32 or FUJITSU ISIS is updated the screens and operations noted in this
chapter will differ slightly.
CONTENTS
2.1 Turning the scanner ON
1
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
2.1 Turning the scanner ON
2.2 Loading Documents on the ADF for
Scanning
2
This section describes how to turn the scanner ON.
The following shows the procedure for turning the scanner ON.
1. Press the power button on the operator panel.
The scanner is turned ON, and the green LED on the operator panel lights.
Also, while the scanner is being initialized, the indication of the Function Number display changes as
follows:
"8"->"P" -> "0" -> "1" The indication "1" means that the operator panel is in the ready status.
2.3 Scanning Documents
2.4 How to Use the Scanner Driver
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
power
button
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
HINT
To turn the scanner OFF, hold the power button down for at least two seconds.
1
2
CONTENTS
2.1 Turning the scanner ON(2)
1
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
2.1 Turning the scanner ON
2.2 Loading Documents on the ADF for
Scanning
2.3 Scanning Documents
2.4 How to Use the Scanner Driver
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
2
Power Save Mode
The Power Save mode keeps the scanner in a low-powered state after it has been turned ON.
If no operation is performed on the scanner for 15 minutes, the scanner automatically switches to the Power
Save mode.
In the Power Save mode, the indication of the Function Number display on the operator panel goes out, but
the green LED stays lit. To return from the Power Save mode, perform one of the following:
1. Load the document on the ADF paper chute.
2. Press any button on the operator panel.
The scanner will be turned OFF when pressing down the power button for at least two seconds.
3. Execute a command from the scanner driver.
1
2
CONTENTS
2.2 Loading Documents on the ADF for Scanning
1
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
2
3
4
5
6
1. Confirm the following items before loading documents.
Confirm that all the documents have the same width.
Check the number of sheets in the document stack.
The standard number of sheets that can be loaded on the scanner is as follows:
❍ A4-size paper or smaller that makes a document stack of 5mm or less
2.1 Turning the scanner ON
❍
Maximum 50 sheet at A4, 20 lb, or 80 g/m2
2.2 Loading Documents on the ADF for
Scanning
2.3 Scanning Documents
2. Fan the documents as follows:
2.4 How to Use the Scanner Driver
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
Lightly grip both ends of the document, then bend and fan it.
Repeat this operation a couple of times.
Rotate the document 90 degrees, then bend and fan it again.
Align the edges of the documents.
1
2
3
4
5
6
CONTENTS
2.2 Loading Documents on the ADF for Scanning(2)
1
INTRODUCTION
2
3
4
5
6
3. Load the document on the ADF paper chute.
Pull out the ADF paper chute extension according to the length of the document.
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
Extension
2.1 Turning the scanner ON
2.2 Loading Documents on the ADF for
Scanning
2.3 Scanning Documents
2.4 How to Use the Scanner Driver
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
Set the documents face-down in the ADF paper chute
(so that the side to be scanned faces towards the ADF paper chute).
Load the document facing the ADF
paper chute.(face down)
1
2
3
4
5
6
CONTENTS
2.2 Loading Documents on the ADF for Scanning(3)
1
2
3
4
5
6
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
ATTENTION
2 BASIC SCANNER OPERATIONS
2.1 Turning the scanner ON
2.2 Loading Documents on the ADF for
Scanning
In case of operating with Windows XP OS:
When the document is set on the ADF paper chute the following window may
appear on the screen.
2.3 Scanning Documents
2.4 How to Use the Scanner Driver
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
In this window, you can select the application program which will perform the
scanning.
By selecting the application program from the "Select the program to launch for
this action" menu and clicking the [OK] button, the selected program will be
iniciated.
For further information, please refer to "APPENDIX A Before using the [Scan]
or the [Send to] button"
1
2
3
4
5
6
CONTENTS
2.2 Loading Documents on the ADF for Scanning(4)
1
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
2.1 Turning the scanner ON
2
3
4
5
6
4. Adjust the side guides to the width of the documents.
Move the side guides so that they touch both sides of the documents.
If there is any space between the side guides and the edges of documents, the scanned image may be
skewed.
Side guides
2.2 Loading Documents on the ADF for
Scanning
2.3 Scanning Documents
2.4 How to Use the Scanner Driver
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
1
2
3
4
5
6
CONTENTS
2.2 Loading Documents on the ADF for Scanning(5)
1
2
3
4
5
6
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
HINT
2 BASIC SCANNER OPERATIONS
2.1 Turning the scanner ON
2.2 Loading Documents on the ADF for
Scanning
2.3 Scanning Documents
2.4 How to Use the Scanner Driver
The stacker prevents document sheets from dropping after they are scanned.
Use the stacker as follows:
1. Lift up the stacker towards you by inserting your fingertips into the handle
on the scanner.
Handle
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
2. Lift the paper stop and swing forward by inserting your fingertips into the
indentations on the scanner as shown in below figure.
Indentation
5. Start up the scanner application, and scan the document.
For details on how to scan documents using the ScandAll 21 application, refer to "2.3 Scanning
Documents"
1
2
3
4
5
6
CONTENTS
2.2 Loading Documents on the ADF for Scanning(6)
1
INTRODUCTION
2
3
4
5
6
With the movie below, review how to load the document onto the ADF:
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
2.1 Turning the scanner ON
2.2 Loading Documents on the ADF for
Scanning
2.3 Scanning Documents
2.4 How to Use the Scanner Driver
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
1
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
2
3
4
5
6
CONTENTS
2.3 Scanning Documents
1
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
2.1 Turning the scanner ON
2.2 Loading Documents on the ADF for
Scanning
2.3 Scanning Documents
2
1. Load the document on the scanner's ADF paper chute.
For details on how to load documents, see "2.2 Loading Documents on the ADF for Scanning".
2. Start up ScandAll 21.
Select [Start] - [Program] - [Scanner Utility for Microsoft Windows] - [ScandAll 21].
This starts up ScandAll 21.
3. Select the scanner to be used.
Select [Select Source] from the [Scan] menu.
2.4 How to Use the Scanner Driver
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
The [Select Source] dialog box appears.
Select "FUJITSU fi-5110Cdj" and click the [Select] button.
4. Click the [Scan To View] button on the tool bar.
The [TWAIN Driver] dialog box (screen for setting the scan conditions) appears.
1
2
CONTENTS
2.3 Scanning Documents(2)
1
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2
5. Set the scan resolution, paper size and other scan conditions, and click the [Scan] button.
For details on settings in the [TWAIN Driver] dialog box, refer to "2.4 How to Use the Scanner
Driver" .
2 BASIC SCANNER OPERATIONS
2.1 Turning the scanner ON
2.2 Loading Documents on the ADF for
Scanning
2.3 Scanning Documents
2.4 How to Use the Scanner Driver
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
The document is scanned, and an image of the scanned document appears on the ScandAll 21
screen.
For details on scanning other types of documents, refer to "Chapter 3 SCANNING VARIOUS TYPES
OF DOCUMENTS" . For details on ScandAll 21 functions and operations, refer to ScandAll 21 Help.
1
2
CONTENTS
2.4 How to Use the Scanner Driver
1
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
2.1 Turning the scanner ON
2.2 Loading Documents on the ADF for
Scanning
2.3 Scanning Documents
2.4 How to Use the Scanner Driver
2
3
4
5
6
7
8
9
10
FUJITSU TWAIN32 Scanner Driver
FUJITSU TWAIN32 Scanner Driver is designed for scanning documents with FUJITSU image scanner fi
series by using application software that complies with the TWAIN standard.
The following describes the procedure with examples of ScandAll 21 for ordinary scanning by using this
driver software.
1. Procedure for Basic Scanning Operation
Startup the application.
From the [Start] menu, select [Programs]-[Scanner Utility for Microsoft Window] and click [ScandAll
21].
Select your scanner on the window below.
Select [Select Source] from the [Scan] menu.
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
Select [FUJITSU fi-5110Cdj] and then click the [Select] button.
Load the documents on the scanner.
For details on loading documents, refer to "2.2 Loading Documents on the ADF for Scanning".
Open the TWAIN Driver window.
Select [Scan To View] from the [Scan] menu.
1
2
3
4
5
6
7
8
9
10
CONTENTS
2.4 How to Use the Scanner Driver(2)
1
2
3
4
5
6
7
8
9
10
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
HINT
2 BASIC SCANNER OPERATIONS
2.1 Turning the scanner ON
2.2 Loading Documents on the ADF for
Scanning
ScandAll 21 provide scanning methods as follows:
●
2.3 Scanning Documents
2.4 How to Use the Scanner Driver
●
●
●
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
●
4 DAILY CARE
●
5 REPLACING CONSUMABLES
[To View...]: Displays scanned images on the window.
[To File...:]: Saves scanned images as files (*.BMP, *.TIF, *.JPG).
[To FTP...:]: Transfers scanned images to a FTP server.
[To Adobe PDF...:]: Saves scanned images as PDF files.
(*Adobe Acrobat must be installed beforehand.)
[To Microsoft Share Point Portal Server...]: Transfers scanned images to
Microsoft Share Point Portal Server.
[To Mail...]: Launches mailer software and attaches scanned images to e-mail.
For details, refer to "ScandAll 21 Help".
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
Configure settings for scanning and click the [Scan] button.
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
For details about the settings on this window, refer to "Setting Window for FUJITSU TWAIN32
Scanner Driver".
The images of scanned documents are displayed on the [ScandAll 21] window.
1
2
3
4
5
6
7
8
9
10
CONTENTS
2.4 How to Use the Scanner Driver(3)
1
2
3
4
5
6
7
8
9
10
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
2.1 Turning the scanner ON
2.2 Loading Documents on the ADF for
Scanning
2.3 Scanning Documents
2.4 How to Use the Scanner Driver
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
Depending on the settings of the application software, images may not be displayed.
For details, refer to the documentation or Help file of your application.
e.x.) When you select [To File...] from the [Scan] menu of ScandAll 21, images of scanned
documents are not displayed on the window.
Save the scanned images.
Select [Save As...] from the [File] menu to save the scanned images.
If you wish to start another scanning, return to procedure 4.
End the application.
Select [Exit] from the [File] menu.
1
2
3
4
5
6
7
8
9
10
CONTENTS
2.4 How to Use the Scanner Driver(4)
1
INTRODUCTION
2
3
4
5
6
7
8
9
10
2. Setting Window for FUJITSU TWAIN32 Scanner Driver
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
2.1 Turning the scanner ON
2.2 Loading Documents on the ADF for
Scanning
2.3 Scanning Documents
2.4 How to Use the Scanner Driver
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
You can configure settings for the FUJITSU TWAIN32 Scanner Driver on this window.
The following describes the main setting items.
❍
❍
For details on each functions, refer to "FUJITSU TWAIN32 Scanner Driver Help" (appears by
pressing [Help] or the [F1] key).
Depending on the type of your scanner, available setting items or range of setting values vary.
1
2
3
4
5
6
7
8
9
10
CONTENTS
2.4 How to Use the Scanner Driver(5)
1
2
3
4
5
6
7
8
9
10
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
Resolution
2.3 Scanning Documents
Specifies the resolution of scanning.
It can be specified by selecting a default value from the list or customizing (specify any resolution in 1
dpi unit).
By marking the [Predefine] checkbox, you can select one from three predefined settings as [Normal],
[Fine], [Super Fine] to scan documents instead of setting details by yourself.
Otherwise, you can change the details of the predefined settings on the [Resolution Setting] window,
which appears when you click on the [...] button.
2.4 How to Use the Scanner Driver
Scan Type
2 BASIC SCANNER OPERATIONS
2.1 Turning the scanner ON
2.2 Loading Documents on the ADF for
Scanning
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
Specifies the feeding method, the side(s) to be scanned (Front Side, Back Side, Duplex) or details of
Long page (the size of documents longer than A4).
Paper Size
4 DAILY CARE
6 TROUBLESHOOTING
Select the size of documents to be scanned from this list.
Windows for customizing the paper size will appear when you click on [...] besides the list. You can
save any document size as a customized setting (up to three) or for changing the order of the paper
size in the list.
7 DOCUMENT SPECIFICATIONS FOR ADF
Image Mode
8 OPTIONS
Specifies the image type for the scanned documents.
5 REPLACING CONSUMABLES
9 SCANNER SPECIFICATIONS
Black & White
Documents are scanned in binary (black and white).
Appendix
Halftone
Documents are scanned through halftone processing in black and
white.
Grayscale
Documents are scanned in gradations from black to white. For this
mode you can select 256 gradations or 4 bit (16 gardations).
Color
Documents are scanned in color. For this mode, you can select 24
bit Color, 256 Color or 8 Color.
[Scan] button
Starts scanning documents with the current settings.
1
2
3
4
5
6
7
8
9
10
CONTENTS
2.4 How to Use the Scanner Driver(6)
1
2
3
4
5
6
7
8
9
10
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
2.1 Turning the scanner ON
2.2 Loading Documents on the ADF for
Scanning
2.3 Scanning Documents
2.4 How to Use the Scanner Driver
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
[Preview] button
Documents are scanned preliminarily before the actual scanning.
You can confirm the image of the documents in the preview window.
[Close] button
Saves the current settings and closes this window.
[Reset] button
Used to undo changes of settings.
[Help] button
Opens the "FUJITSU TWAIN32 Scanner Driver Help" window. The window also opens by pushing the [F1]
key.
4 DAILY CARE
5 REPLACING CONSUMABLES
[About...] button
Opens an information window about the FUJITSU TWAIN32 Scanner Driver's version.
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
1
2
3
4
5
6
7
8
9
10
CONTENTS
2.4 How to Use the Scanner Driver(7)
1
2
3
4
5
6
7
8
9
10
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
[Option...] button
You can set up the details of optional functions on the window below.
2.1 Turning the scanner ON
2.2 Loading Documents on the ADF for
Scanning
2.3 Scanning Documents
2.4 How to Use the Scanner Driver
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
[Rotation] tab
Select this tab when setting image rotation, detection of document size, etc.
[Job/Cache] tab
Select this tab when setting cache mode, multi feed detection, blank page skipping, etc.
[Generic] tab
Select this tab to change the unit displayed on the Setting Window for the FUJITSU TWAIN32
Scanner Driver. (Millimeters, Inches, and Pixels are available)
[Startup] tab
Select this tab for setting the Scanner Operation Panel.
[Filter] tab
Select this tab for setting the image processing filter(s).
Page Edge Filler: Fills up the margins of the scanned documents with a selected color.
Digital Endoser: A character string, such as the alphabet and numbers, can be added in the scanned
document.
[Compression] tab
Select this tab for setting the compression rate of JPEG Transfer.
1
2
3
4
5
6
7
8
9
10
CONTENTS
2.4 How to Use the Scanner Driver(8)
1
2
3
4
5
6
7
8
9
10
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
2.1 Turning the scanner ON
2.2 Loading Documents on the ADF for
Scanning
2.3 Scanning Documents
2.4 How to Use the Scanner Driver
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
[Advance...] button
Click this button for settings of the advanced image processing.
You can set Edge Extract, Gamma Pattern, White Level Follower, Dropout Color, Reverse, etc.
[Config...] button
Click this button for configuring the Setting Files.
You can save the changed settings as a Setting File. From next scanning, the settings are quickly
changed by using these Setting Files.
For details of each function, refer to the "FUJITSU TWAIN32 Scsnner Driver Help".
1
2
3
4
5
6
7
8
9
10
CONTENTS
2.4 How to Use the Scanner Driver(9)
1
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
2.1 Turning the scanner ON
2.2 Loading Documents on the ADF for
Scanning
2.3 Scanning Documents
2.4 How to Use the Scanner Driver
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
2
3
4
5
6
7
8
9
10
FUJITSU ISIS Scanner Driver
FUJITSU ISIS Scanner Driver is designed for scanning documents with FUJITSU image scanner fi series by
using application software that complies with The ISIS standard.
The following describes the procedure with examples of QuickScan for ordinary scanning by using this driver
software.
The procedure may vary depending on your application. If you use an application other than QuickScan,
please refer to its Guide or Help for further information.
1. Procedure for Basic Scanning Operation
Startup the application.
From the [Start] menu, select [Programs] - [QuickScan] and click [QuickScan].
Select your scanner on the window below.
Select [Scan] - [Select Scanner] on the menu bar.
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
Select fi-5110C, then click the [OK] button.
Select [Scan] - [New Batch] on the menu bar.
1
2
3
4
5
6
7
8
9
10
CONTENTS
2.4 How to Use the Scanner Driver(10)
10
INTRODUCTION
11
12
13
14
15
16
Select the profile for scanning.
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
2.1 Turning the scanner ON
2.2 Loading Documents on the ADF for
Scanning
2.3 Scanning Documents
2.4 How to Use the Scanner Driver
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
❍
When creating a new profile
Select one from an already existing profiles and click the [Add Profile...] button.
A new profile will be created based on the profile you selected.
Appendix
❍
When changing the settings of already existing profiles
Select one from an already existing profiles and click [Edit Profile...] button.
The settings of the selected profile can be changed.
❍
When using an existing profile.
Select one from the already existing profiles.
Scanning will be started according to the settings of the selected profile.
Go to procedure 9.
Select the [Scan] tab and click the [Scanner Settings] on the [Profile Editor] window.
The configuration window of ISIS driver appears.
10
11
12
13
14
15
16
CONTENTS
2.4 How to Use the Scanner Driver(11)
10
INTRODUCTION
11
12
13
14
15
16
Configure settings for scanning and click the [OK] button.
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
2.1 Turning the scanner ON
2.2 Loading Documents on the ADF for
Scanning
2.3 Scanning Documents
2.4 How to Use the Scanner Driver
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
For details on this dialog box, refer to "Configuration Window of FUJITSU ISIS Scanner
Driver".
The [Profile Editor] window appears. Click the [OK] button to return to [New batch] dialog.
Load the documents on the scanner.
Click the [Scan] button.
Scanned images are displayed on the window.
Refer to the "QuickScan Overview" or the "QuickScan Help" for further information on
functions and operations of QuickScan. After the installation of QuickScan, it is registered in
the [Start] menu.
10
11
12
13
14
15
16
CONTENTS
2.4 How to Use the Scanner Driver(12)
10
INTRODUCTION
11
12
13
14
15
16
2. Configuration Window of FUJITSU ISIS Scanner Driver
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
2.1 Turning the scanner ON
2.2 Loading Documents on the ADF for
Scanning
2.3 Scanning Documents
2.4 How to Use the Scanner Driver
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
Image Mode
Select a color mode suitable for the purpose from the menu.
Black & White
Scans data in binary (black and white).
Distinguishes black from white according
to the fixed threshold. This scanning
mode is suitable for scanning line
drawings and text documents.
16-level Grayscale
Scans data by 14 shades of gray plus
black and white. This mode uses 4 bits
per pixel.
256-level Grayscale
Scans data by 254 shades of gray plus
black and white. This mode uses 8 bits
per pixel. This mode is switable for
scanning monochrome photographs.
24-bit Color
Scans data as full-colored image using
24 bits per pixel. This mode is suitable
for scanning color photographs.
Image Processing
Binary processing is applied to the
scanned images This mode is available
only when Image Processing Software
Option (separately sold) is installed.
Please refer to the "User's Guide of
Image Processing Software Option" for
details.
Resolution
Specifies the number of pixels (dots) per inch.
Select a fixed resolution from the list or enter any value (from 50 to 600) manually.
A higher resolution produces finer image, but requires much more memory.
10
11
12
13
14
15
16
CONTENTS
2.4 How to Use the Scanner Driver(13)
10
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
11
12
2.3 Scanning Documents
This setting is suitable for scanning
dark photographs.
Dither Pattern 1
This setting is suitable for scanning
dark-colored documents containing
both text and photographs.
Dither Pattern 2
This setting is suitable for scanning
light photographs.
Dither Pattern 3
This setting is suitable for scanning
light-colored documents containing
both text and photographs.
Error Diffusion
This function minimizes differences
of color levels due to subtractive
color process by diffusing the
difference to the adjacent pixels.
This mode is suitable for scanning
images of photographs, etc.
Download
Executes processing with the
dithered download pattern specified
in the dithered download file.
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
16
Dither Pattern
4 DAILY CARE
5 REPLACING CONSUMABLES
15
Select the halftone pattern for halftone scanning. This setting is available when "Black
& White" is selected in the "Image Mode"
2.4 How to Use the Scanner Driver
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
14
Halftone
2.1 Turning the scanner ON
2.2 Loading Documents on the ADF for
Scanning
13
9 SCANNER SPECIFICATIONS
Appendix
Brightness
Sets the brightness of the entire image. Specify the brightness as a number within the
range of 1 (dark) to 255 (bright). To brighten the entire image, increase the value of
the setting. To darken the entire image, decrease the value.
Contrast
Sets the contrast between light and shadow of the scanned image. Specify the
contrast as a number within the range of 1 (low [soft]) to 255 (high [sharp]). Increasing
this value makes the contrast sharper.
10
11
12
13
14
15
16
CONTENTS
2.4 How to Use the Scanner Driver(14)
10
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
11
12
13
14
15
16
Scan Type
Selects the scanning method
2 BASIC SCANNER OPERATIONS
2.1 Turning the scanner ON
ADF (Front Side)
Scans only the front sides of
documents.
2.2 Loading Documents on the ADF for
Scanning
ADF (Back Side)
Scans only back sides of documents.
ADF (Duplex)
Scans both front and the back sides
of documents. When this option is
selected, the both sides of documents
are scanned simultaneously.
2.3 Scanning Documents
2.4 How to Use the Scanner Driver
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
Paper Size
Selects a paper size according to the size of the document to be scanned. Select a
standard paper size from the list.
Page Layout
9 SCANNER SPECIFICATIONS
Appendix
Specifies orientation of the documents as portrait or landscape.
10
11
12
13
14
15
16
CONTENTS
2.4 How to Use the Scanner Driver(15)
10
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
2.1 Turning the scanner ON
11
12
13
14
15
16
[Area...] button
Opens the Scan Area dialog box.
Specify scan area for the document size.
The size can be set by dragging the frame with mouse.
Otherwise, enter any value for the setting.
2.2 Loading Documents on the ADF for
Scanning
2.3 Scanning Documents
2.4 How to Use the Scanner Driver
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
[JPEG...] button
Opens the JPEG Settings dialog box. Used for setting the compression rate of JPEG
transfer.
[About...] button
This button displays the version information.
10
11
12
13
14
15
16
CONTENTS
2.4 How to Use the Scanner Driver(16)
10
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
11
12
13
14
15
16
[More...] button
Opens [More Settings] window. Used for setting advanced features.
2 BASIC SCANNER OPERATIONS
2.1 Turning the scanner ON
2.2 Loading Documents on the ADF for
Scanning
2.3 Scanning Documents
2.4 How to Use the Scanner Driver
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
DTC Variance
This option specifies the value for adjusting the variance based on the brightness of the
image.
Edge Processing
This option specifies the sharpness of contour extraction.
Low, Mid, High
Emphasizes contour of images. Available
settings are: Low, Mid, High
Smoothing
Smoothes jaggy images.
Dropout Color
This option excludes selected color (the three primary colors of light i.e. green, red, blue)
from scanned images. For example, if the document contains black text in a red frame and
when the red color is selected, the scanner reads only the text and eliminate (drop out) the
red frame.
If you do not wish to have any colors dropped out select "None".
Reverse
Colors of scanned images are reversed.
End of Page Detection
Scans the edge (bottom) of the documents and outputs data adjusted to the document
length. When any page shorter than specified "Paper Size" is included, the output size is
adjusted to the detected short size.
Gamma
Specifies Gamma correction. Correction patterns are: "Normal", "Soft", "Sharp", "Custom", or
"Download".
Multi Feed Detection
Detects multi feeds (phenomena that two or more sheets are accidentally fed). You can set
conditions for detecting multi feeds so that the scanner should stop and display error
messages. Multi feeds are scanned by the differences in document lengths or thicknesses.
10
11
12
13
14
15
16
CONTENTS
3 SCANNING VARIOUS TYPES OF DOCUMENTS
This chapter describes how to scan various types of documents.
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
3.1 Scanning Double Sided Documents
3.2 Scanning Different-width Documents
3.3 Scanning Documents longer than A4 size
3.4 Saving Scanned Images in PDF Format
3.5 Excluding a Color in the Image (dropout
color)
3.6 Skipping blank pages
3.7 Detecting Multi Feeds
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
In this chapter Windows XP screenshots are illustrated.
The screens and operations may differ slightly if the OS that you are using is other than Windows XP.
Also, when FUJITSU TWAIN32 or FUJITSU ISIS is updated the screens and operations noted in this
chapter will differ slightly.
CONTENTS
3.1 Scanning Double Sided Documents
1
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
2
3
The following shows the procedure for reading the double sided documents.
1. Load the document on the ADF paper chute.
For details on how to load documents, see "2.2 Loading Documents on the ADF for Scanning".
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
3.1 Scanning Double Sided Documents
3.2 Scanning Different-width Documents
3.3 Scanning Documents longer than A4 size
3.4 Saving Scanned Images in PDF Format
3.5 Excluding a Color in the Image (dropout
color)
Load the document with facing the ADF
paper chute.(face down)
3.6 Skipping blank pages
3.7 Detecting Multi Feeds
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
2. Adjust the side guides to the width of the documents.
Side
Guides
1
2
3
CONTENTS
3.1 Scanning Double Sided Documents(2)
1
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
2
3
3. Start up ScandAll 21.
From [Start] menu, select [Program] - [Scanner Utility for Microsoft Windows] - [ScandAll 21].
This starts up ScandAll 21.
4. Select [Select Source] from the [Scan] menu.
5. Select [FUJITSU fi-5110Cdj] and then click the [Select] button.
3.1 Scanning Double Sided Documents
3.2 Scanning Different-width Documents
6. Click [Scan To View] on the tool bar. The [TWAIN Driver] dialogbox appears.
3.3 Scanning Documents longer than A4 size
3.4 Saving Scanned Images in PDF Format
7. Select [ADF (Duplex)] from [Scan Type].
3.5 Excluding a Color in the Image (dropout
color)
3.6 Skipping blank pages
3.7 Detecting Multi Feeds
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
1
2
3
CONTENTS
3.1 Scanning Double Sided Documents(3)
1
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2
3
7. Click the [Scan] button.
For [TWAIN Driver] dialog box setting, refer to "2.4 How to Use the Scanner Driver".
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
3.1 Scanning Double Sided Documents
3.2 Scanning Different-width Documents
3.3 Scanning Documents longer than A4 size
3.4 Saving Scanned Images in PDF Format
3.5 Excluding a Color in the Image (dropout
color)
3.6 Skipping blank pages
3.7 Detecting Multi Feeds
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
The document is scanned, and an image of the scanned document appears on the ScandAll 21
screen. For ScandAll functions and operation, refer to [ScandAll 21 Help].
9 SCANNER SPECIFICATIONS
Appendix
1
2
3
CONTENTS
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
3.1 Scanning Double Sided Documents
3.2 Scanning Different-width Documents
3.3 Scanning Documents longer than A4 size
3.4 Saving Scanned Images in PDF Format
3.5 Excluding a Color in the Image (dropout
color)
3.6 Skipping blank pages
3.7 Detecting Multi Feeds
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
3.2 Scanning Different-width Documents
When you scan a batch of documents with different widths by using the ADF, you may get skewed images
from smaller sized documents.
Be sure to scan only documents of the same width together.
The following shows the procedure for scanning a batch of mixed size documents.
1. Sort out the batch into stacks of the same width.
2. Adjust the side guides to the width of each document stack.
3. Scan the batches of the same widths sparately one by one.
For details on how to load documents, see "2.3 Scanning Documents".
CONTENTS
3.3 Scanning Documents longer than A4 size
1
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2
3
1. Load the documents on the ADF paper chute.
For details on loading documents, refer to "2.2 Loading Documents on the ADF for Scanning".
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
3.1 Scanning Double Sided Documents
3.2 Scanning Different-width Documents
3.3 Scanning Documents longer than A4 size
3.4 Saving Scanned Images in PDF Format
Load the document with facing the ADF
paper chute.(face down)
3.5 Excluding a Color in the Image (dropout
color)
3.6 Skipping blank pages
3.7 Detecting Multi Feeds
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
2. Adjust the side guides to the document width.
9 SCANNER SPECIFICATIONS
Appendix
Side
Guides
1
2
3
CONTENTS
3.3 Scanning Documents longer than A4 size(2)
1
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
2
3
3. Start up ScandAll 21.
For starting up ScandAll 21, select [Programs] - [Scanner Utility for Microsoft Windows] - [ScandAll
21] from [Start].
4. Select [Select Source] from the [Scan] menu.
5. Select [FUJITSU fi-5110Cdj] and then click the [Select] button.
3.1 Scanning Double Sided Documents
3.2 Scanning Different-width Documents
3.3 Scanning Documents longer than A4 size
3.4 Saving Scanned Images in PDF Format
6. Click [Scan To View] on the tool bar.
The [TWAIN Driver] dialogbox appears.
7. Select [Long page (Front Side)] or [Long page (Duplex)] from [Scan Type].
3.5 Excluding a Color in the Image (dropout
color)
3.6 Skipping blank pages
3.7 Detecting Multi Feeds
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
8. Specify the length of documents.
1
2
3
CONTENTS
3.3 Scanning Documents longer than A4 size(3)
1
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2
3
8. Click the [Scan] button.
For settings in the [TWAIN Driver] dialogbox, refer to "2.4 How to Use the Scanner Driver".
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
3.1 Scanning Double Sided Documents
3.2 Scanning Different-width Documents
3.3 Scanning Documents longer than A4 size
3.4 Saving Scanned Images in PDF Format
3.5 Excluding a Color in the Image (dropout
color)
3.6 Skipping blank pages
3.7 Detecting Multi Feeds
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
Images of scanned documents are displayed on the window of ScandAll 21.
For details on functions and operations of ScandAll 21, refer to "ScandAll 21 Help".
9 SCANNER SPECIFICATIONS
Appendix
1
2
3
CONTENTS
3.4 Saving Scanned Images in PDF Format
1
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
3.1 Scanning Double Sided Documents
3.5 Excluding a Color in the Image (dropout
color)
3.6 Skipping blank pages
3.7 Detecting Multi Feeds
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
5
6
7
1. Using ScandAll 21
This method is recommended for color or grayscale scanning and when smaller PDF file size is
required.
The benefits are:
❍
Reduced PDF data size
Simplified method for creating PDF files with no troublesome operations
2. Using Adobe Acrobat 6.0
This method is recommended for faster creation of PDF files and for black and white scanning.
The benefits are:
❍
❍
4 DAILY CARE
4
There are 2 ways for saving scanned images in PDF format.
❍
3.4 Saving Scanned Images in PDF Format
3
To save scanned images in PDF format, Adobe Acrobat 6.0 or later must be installed on your PC. Adobe
Acrobat 6.0 can be installed from the provided Adobe Acrobat CD-ROM.
3.2 Scanning Different-width Documents
3.3 Scanning Documents longer than A4 size
2
Quick creation of PDF files with the original scan resolution
Flexibile creation of PDF files by changing the PDF compression rates
Grayscale or color scanning creates larger file sizes than black and white scanning. If the file size is
very large, you can reduce the file size by configuring the properties of Acrobat Distiller before saving
scanned images. For details, please refer to the hints on page (6).
1
2
3
4
5
6
7
CONTENTS
3.4 Saving Scanned Images in PDF Format(2)
1
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2
3
4
5
6
7
Using ScandAll 21
1. Load the documents on the ADF paper chute.
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
3.1 Scanning Double Sided Documents
3.2 Scanning Different-width Documents
2. Start up ScandAll 21.
From [Start] menu, select [Program] - [Scanner Utility for Microsoft Windows] [ScandAll 21]. This starts up ScandAll 21.
3. From the menu bar select [Scan] and then [To Adobe PDF] from the pull down menu.
3.3 Scanning Documents longer than A4 size
3.4 Saving Scanned Images in PDF Format
3.5 Excluding a Color in the Image (dropout
color)
3.6 Skipping blank pages
3.7 Detecting Multi Feeds
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
[TWAIN Driver] dialog box is displayed.
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
1
2
3
4
5
6
7
CONTENTS
3.4 Saving Scanned Images in PDF Format(3)
1
INTRODUCTION
2
3
4
5
6
7
4. Select the scan resolution, document size and other scan conditions, and then click the [Scan]
button.
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
3.1 Scanning Double Sided Documents
3.2 Scanning Different-width Documents
3.3 Scanning Documents longer than A4 size
3.4 Saving Scanned Images in PDF Format
3.5 Excluding a Color in the Image (dropout
color)
3.6 Skipping blank pages
3.7 Detecting Multi Feeds
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
5. To end scanning, click the [Close] button.
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
6. Enter the file name and select the destination to save the scanned image.
For details, refer to ScandAll 21 Help.
1
2
3
4
5
6
7
CONTENTS
3.4 Saving Scanned Images in PDF Format(4)
1
INTRODUCTION
2
3
4
5
6
7
Using Adobe Acrobat 6.0
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
ATTENTION
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
3.1 Scanning Double Sided Documents
3.2 Scanning Different-width Documents
Usage note for Adobe Acrobat 6.0
●
3.3 Scanning Documents longer than A4 size
3.4 Saving Scanned Images in PDF Format
3.5 Excluding a Color in the Image (dropout
color)
●
The following functions cannot be used:
❍
"256 Color" or "8 Color"
❍
3.6 Skipping blank pages
3.7 Detecting Multi Feeds
4 DAILY CARE
Acrobat's default settings overrides the previous settings for
"Resolution", "Scan Type" and "Image Mode".
❍
"Rotation Degree" selection when "End of Page Detection" is
selected
Long Page Scanning
1. Load the documents on the ADF paper chute.
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
2. Start up Adobe Acrobat 6.0.
Select [Program] - [Adobe Acrobat 6.0] from the [Start] menu. This starts up Adobe Acrobat 6.0.
3. From the [File] menu select [Create PDF] - [From Scanner].
9 SCANNER SPECIFICATIONS
Appendix
[Create PDF From Scanner] dialog box appears.
4. Select [FUJITSU fi-5110Cdj] at [Device] and click [Scan] button.
[TWAIN driver] dialog box is displayed.
1
2
3
4
5
6
7
CONTENTS
3.4 Saving Scanned Images in PDF Format(5)
1
INTRODUCTION
2
3
4
5
6
7
5. Select the scan resolution, document size and other scan conditions, and click the [Scan] button.
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
3.1 Scanning Double Sided Documents
3.2 Scanning Different-width Documents
3.3 Scanning Documents longer than A4 size
3.4 Saving Scanned Images in PDF Format
3.5 Excluding a Color in the Image (dropout
color)
3.6 Skipping blank pages
3.7 Detecting Multi Feeds
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
6. To end scanning, click the [Done] button.
9 SCANNER SPECIFICATIONS
Appendix
The scanned image is displayed.
1
2
3
4
5
6
7
CONTENTS
3.4 Saving Scanned Images in PDF Format(6)
1
INTRODUCTION
2
3
4
5
6
7
7. Select [Save as...] or [Save] from [File] menu to save the scanned image.
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
3.1 Scanning Double Sided Documents
3.2 Scanning Different-width Documents
3.3 Scanning Documents longer than A4 size
3.4 Saving Scanned Images in PDF Format
3.5 Excluding a Color in the Image (dropout
color)
For the details on Adobe Acrobat 6.0 operations, refer to the Adobe Acrobat 6.0 manual and Help.
3.6 Skipping blank pages
3.7 Detecting Multi Feeds
4 DAILY CARE
HINT
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
If you save scanned images by this procedure, the file size may increase greatly. For
reducing the file size, follow the procedure below. (It may take much more time than
the usual saving procedure.)
1. Select [File] - [Print...].
2. On the following dialog specify [Adobe PDF] for [Name].
Appendix
3. Click the [Properties] button.
4. Click the [Adobe PDF settings] tab.
1
2
3
4
5
6
7
CONTENTS
3.4 Saving Scanned Images in PDF Format(7)
1
2
3
4
5
6
7
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
HINT(Continued from the previous page)
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
5. Select one from [Default Settings].
The following shows an example of [Standard].
3.1 Scanning Double Sided Documents
3.2 Scanning Different-width Documents
3.3 Scanning Documents longer than A4 size
3.4 Saving Scanned Images in PDF Format
3.5 Excluding a Color in the Image (dropout
color)
3.6 Skipping blank pages
3.7 Detecting Multi Feeds
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
6. Click the [OK] button.
7. Enter a file name and click the [Save] button on the [Save PDF File As] dialogbox.
1
2
3
4
5
6
7
CONTENTS
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
3.5 Excluding a Color in the Image (dropout color)
A selected color (primary colors: red, green or blue) can be removed (dropped out) from the scanned image
data.
For example, if the document contains black text in a green frame, you can set the scanner to read only the
text and eliminate (drop out) the green frame.
To set the scanner to drop out a color, change the settings in the [TWAIN Driver] dialogbox before scanning.
1. Click the [Advance...] button in the [TWAIN Driver] dialog box.
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
3.1 Scanning Double Sided Documents
3.2 Scanning Different-width Documents
3.3 Scanning Documents longer than A4 size
3.4 Saving Scanned Images in PDF Format
3.5 Excluding a Color in the Image (dropout
color)
3.6 Skipping blank pages
3.7 Detecting Multi Feeds
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
The [Advance] dialog box appears.
2. Select the color to be drop out from "Dropout Color" under "More".
For example, if the document contains black text in green frame, select [Green] so that the scanner
only reads the text and eliminates the frames.
If you do not wish to have any colors dropped out select "None".
3. Click the [OK] button.
The [TWAIN Driver] dialog box will be redisplayed.
Continue scanning from this dialog box.
CONTENTS
3.6 Skipping blank pages
1
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2
Change settings in the [TWAIN Driver] dialog box for skipping blank pages at scanning documents.
1. Click [Option] button in the [TWAIN Driver] dialog box.
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
3.1 Scanning Double Sided Documents
3.2 Scanning Different-width Documents
3.3 Scanning Documents longer than A4 size
3.4 Saving Scanned Images in PDF Format
3.5 Excluding a Color in the Image (dropout
color)
3.6 Skipping blank pages
3.7 Detecting Multi Feeds
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
The [Option] dialog box appears.
2. Click the [Job/Cache] tab.
Appendix
3. Check the [Blank Page Skip] box.
If an item other than "Ram cache" or "Use Both Memory" has been selected in the [Cache Mode:] and
this check box is marked, it will change to "Ram cache".
1
2
CONTENTS
3.6 Skipping blank pages(2)
1
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2
4. With the slider control under [Blank Page Skip], specify the Blank Page Skip degree.
<In Binary/Halftone mode>
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
3.1 Scanning Double Sided Documents
3.2 Scanning Different-width Documents
3.5 Excluding a Color in the Image (dropout
color)
For white pages, use the [Black Dots Ratio] slider bar to set the skip condition. For black pages, use
the [White Dots Ratio] scroll bar to set the skip condition.
The value displayed to the right of the scroll bar displays the noise ratio(*1). If a scanned document
is below this value, it is recognized as a blank page. The setting range is OFF(- -) and 0.2% to 3.0%
(in increments of 0.2%).
*1: Ratio of black dots included in the scanning area. (for white pages)
3.6 Skipping blank pages
<In Color/Grayscale mode>
3.3 Scanning Documents longer than A4 size
3.4 Saving Scanned Images in PDF Format
3.7 Detecting Multi Feeds
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
Use the slider bar to set the skip condition in five stages from 1 to 5. To make the blank pages easy
to skip, increase the value of the setting.
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
1
9 SCANNER SPECIFICATIONS
Appendix
2
CONTENTS
3.7 Detecting Multi Feeds
1
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
2
"Multi feed" is a feeding error that occurs when two or more sheets in the ADF paper chute are fed
simultaneously into the scanner.
You can set the scanner to detect multi feed, stop scanner operation, and display an error message.
To set the scanner to detect multi feed, change the settings in the [TWAIN Driver] dialog box.
1. Click the [Option...] button in the [TWAIN Driver] dialog box.
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
3.1 Scanning Double Sided Documents
3.2 Scanning Different-width Documents
3.3 Scanning Documents longer than A4 size
3.4 Saving Scanned Images in PDF Format
3.5 Excluding a Color in the Image (dropout
color)
3.6 Skipping blank pages
3.7 Detecting Multi Feeds
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
The [Option] dialog box appears.
2. Click the [Job/Cache] tab.
1
2
CONTENTS
3.7 Detecting Multi Feeds(2)
1
INTRODUCTION
2
3. Select the detection conditions from "Multi Feed Detection" under "ADF Option".
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
3.1 Scanning Double Sided Documents
3.2 Scanning Different-width Documents
3.3 Scanning Documents longer than A4 size
3.4 Saving Scanned Images in PDF Format
3.5 Excluding a Color in the Image (dropout
color)
3.6 Skipping blank pages
3.7 Detecting Multi Feeds
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
The following detection conditions are provided:
None
Multi feed detection is not performed.
Check thickness
The scanner monitors the thickness of documents.
It detects a multi feed by differences in document
thickness when two or more document sheets are
fed overlapping.
Check length
The scanner monitors the length of documents. It
detects a multi feed by changes in the document
length when two or more document sheets are fed
overlapping.
Check thickness and length
The scanner monitors both document thickness
and length to detect multi feed.
9 SCANNER SPECIFICATIONS
Appendix
Furthermore, see "7.5 Multi feed Detection Conditions" for detailed information about the document
for multi feed detection.
4. Click the [OK] button.
The display returns to the [TWAIN Driver] dialog box. Continue scanning from this dialog box.
1
2
CONTENTS
4 DAILY CARE
This chapter describes how to clean the scanner.
CAUTION
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
4.1 Cleaning Materials
4.2 Cleaning the Scanner Exterior
4.3 Cleaning the Inside of the Scanner
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
When operating the scanner, the ADF's glass becomes very hot.
Before you clean inside the scanner, turn off its power and unplug
the AC adapter from the outlet. Wait for at least 15 minutes.
Do not turn off the scanner when you clean the Feed rollers.
CONTENTS
4.1 Cleaning Materials
The table below shows the cleaning materials that are used on this scanner.
Cleaning Materials
Part No.
Remarks
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
Cleaner F1
(or isopropyl alcohol)
CA99501-0013
1 bottle (100 ml)
Moisten cloth with this fluid and wipe the
scanner clean.
Lint-free dry cloth
Commercially available.
Any lint-free cloth can be used.
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
4.1 Cleaning Materials
4.2 Cleaning the Scanner Exterior
4.3 Cleaning the Inside of the Scanner
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
To purchase the Cleaner F1, please contact the FUJITSU scanner dealer where you purchased the scanner.
CONTENTS
4.2 Cleaning the Scanner Exterior
Clean the scanner exterior, the ADF paper chute and the Stacker with a cloth moistened with a small amount
of Cleaner F1 or any neutral detergent
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
ATTENTION
2 BASIC SCANNER OPERATIONS
●
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
4.1 Cleaning Materials
4.2 Cleaning the Scanner Exterior
4.3 Cleaning the Inside of the Scanner
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
●
●
Never use paint thinner and other organic solvents.
During the cleaning, prevent water or moisture from getting inside the
scanner.
Do not use aerosol sprays to clean the scanner.
Aerosol sprays cause dirt and dust to enter the scanner, resulting
scanner failure and malfunction.
CONTENTS
4.3 Cleaning the Inside of the Scanner
1
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
2
3
4
5
Clean inside of the scanner with a cloth moistened with Cleaner F1.
In an alternating succession of scanning documents, the accumulated paper-powder and dust inside the
scanner causes a scanning error.
As a guideline, clean the ADF every 1,000 scans. Note that this guideline varies according to the type of the
documents you are scanning. For example, the ADF must be cleaned more frequently when scanning
documents on that the toner has not been sufficiently fixed on.
Clean the ADF according to the following procedure referring to the illustrations on the following page.
4 DAILY CARE
4.1 Cleaning Materials
CAUTION
4.2 Cleaning the Scanner Exterior
4.3 Cleaning the Inside of the Scanner
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
The glass surface inside the ADF becomes hot during the scanner operation.
Before you start to clean the inside of the scanner, disconnect the AC adapter
from the outlet and wait at least 15 minutes to let the scanner cool down.
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
ATTENTION
Appendix
●
●
Do not use water or neutral detergent to clean the inside of the scanner.
Do not use aerosol sprays to clean the scanner.
Aerosol sprays cause dirt and dust to enter the scanner, resulting scanner
failure and malfunction.
1
2
3
4
5
CONTENTS
4.3 Cleaning the Inside of the Scanner (2)
1
2
3
4
5
1. Open the ADF by pulling the ADF open lever.
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
CAUTION
Be careful, the ADF may close and pinch your finger.
4 DAILY CARE
4.1 Cleaning Materials
4.2 Cleaning the Scanner Exterior
2. Clean the following locations with a cloth moistened with cleaner F1.
4.3 Cleaning the Inside of the Scanner
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
No.
Name
1
Pad ASSY
2
Plastic Rollers (x4)
3
Feed Rollers (x4)
4
Pick Roller
5
Glasses (x2)
1
2
3
4
5
CONTENTS
4.3 Cleaning the Inside of the Scanner (3)
1
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2
3
4
5
Turn off the scanner before cleaning the following locations.
●
Pad ASSY (x 1)
Wipe the Pad ASSY (rubber surface) downwards. When cleaning the Pad ASSY, take care to prevent
the cloth from catching on the metallic parts.
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
Metallic parts
4 DAILY CARE
4.1 Cleaning Materials
4.2 Cleaning the Scanner Exterior
The portion to
clean
4.3 Cleaning the Inside of the Scanner
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
●
9 SCANNER SPECIFICATIONS
ADF glass surfaces (x 2: located on the ADF and the opposite side)
Clean lightly.
Appendix
HINT
If the glass is dirty, vertical black streaks may appear in the
scanned images.
●
Plastic rollers (x 4)
Clean them lightly while rotating the rollers with your finger. Take care not to roughen the surface of the
rollers. Take particular care in cleaning the plastic rollers since black debris on the rollers adversely
affect the pickup performance.
●
Pick roller (x 1)
Lightly clean the Pick roller taking care not to scratch the roller surfaces and the Mylar sheet. Take
particular care in cleaning this roller as black debris on it adversely affect the pickup performance.
Mylar sheet
With the movie below, review the procedure to clean the Pad ASSY, ADF glass surfaces, Plastic
rollers and the Pick roller:
1
2
3
4
5
CONTENTS
4.3 Cleaning the Inside of the Scanner (4)
1
2
3
4
5
Turn on the scanner before cleaning the following locations.
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
●
Feed rollers (x 4)
Clean lightly taking care not to roughen the surface of the rollers. Take particular care in cleaning the
feed rollers since black debris on the rollers adversely affect the pickup performance.
1. Open the ADF when the indication of the Function Number display is not "P" or "0".
If you open the ADF when the indication of the Function Number display is "P" or "0", the
Feed rollers will not rotate even you perform the operation of step 2) below.
4.1 Cleaning Materials
4.2 Cleaning the Scanner Exterior
4.3 Cleaning the Inside of the Scanner
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
2. Simultaneously hold down the "Send to" and "Scan" buttons on the operator panel.
The Feed rollers start to rotate slowly.
For details on where the "Send to" and "Scan" buttons are located, refer to the
following illustration.
3. Hold a soft, dry cloth moistened with cleaning fluid against the surface of the rotating Feed
rollers so that it lightly cleans the surface of the rollers.
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
As a guideline, 6 presses of the "Send to" and "Scan" buttons make the Feed rollers to rotate
one full turn.
9 SCANNER SPECIFICATIONS
Appendix
CAUTION
In step 2, all the Feed rollers turn at the same time. When cleaning the
Feed rollers positioned in the lower part of the ADF, be caereful not to
touch the other Feed rollers.
1
2
3
4
5
CONTENTS
4.3 Cleaning the Inside of the Scanner (5)
1
2
3
4
5
With the movie below, review the procedure to clean the Feed Rollers:
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
4.1 Cleaning Materials
4.2 Cleaning the Scanner Exterior
4.3 Cleaning the Inside of the Scanner
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
3. Close the ADF.
9 SCANNER SPECIFICATIONS
Appendix
CAUTION
After closing the ADF, make sure that it is completely closed.
Otherwise, paper jams or other feeding errors may occur.
1
2
3
4
5
CONTENTS
5 REPLACING CONSUMABLES
This chapter describes how to replace scanner consumables.
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
In this chapter Windows XP screenshots are illustrated.
The screens and operations may differ slightly if the OS that you are using is not Windows XP.
Also, when FUJITSU TWAIN32 or FUJITSU ISIS is updated the screens and operations noted in this
chapter will differ slightly.
CAUTION
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
5.1 Consumable and Replacement Cycle
5.2 Replacing the Pad ASSY
5.3 Replacing the Pick Roller
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
When operating the scanner, the ADF's inside glass becomes very
hot.
Before you replace the consumables, turn off its power and unplug
the AC adapter from the outlet. Wait for at least 15 minutes.
CONTENTS
5.1 Consumable and Replacement Cycle
1
2
3
4
5
The following table shows the specifications of consumables and their standard replacement cycle.
INTRODUCTION
Description
1 NAMES AND FUNCTIONS OF PARTS
PAD ASSY
Parts Number
Standard Replacement Cycle
PA03360-0002
After 50,000 scans or one year.
PA03360-0001
100,000 scans or one year.
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
5.1 Consumable and Replacement Cycle
5.2 Replacing the Pad ASSY
Pick Roller
5.3 Replacing the Pick Roller
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
The replacement cycles above are rough guidelines for the case of using A4/Letter woodfree or wood
containing paper 64 g/m2 (17 lb). This cycle varies according to the type of the used paper and how
frequently the scanner is used and cleaned.
ATTENTION
Use only the consumables specified by PFU LIMITED. Do not use
consumables and parts made by other manufacturers.
To purchase the consumables, contact the FUJITSU scanner dealer where you purchased the scanner or
an authorized FUJITSU scanner service provider.
1
2
3
4
5
CONTENTS
5.1 Consumable and Replacement Cycle (2)
1
2
3
4
5
Guidelines for Consumable Replacement Cycle
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
With this product, you can learn how many times the consumables are used so that you can estimate the
right timing for the replacement.
1. When turning on the power, check that the scanner is connected to the PC.
Refer to "2.3 Connecting the USB cable " in fi-5110C Getting Started on the Setup CD-ROM for
information about connecting the scanner to a personal computer.
2. Double click the "Printer and Other Hardware" icon on the operator panel of the host computer.
5 REPLACING CONSUMABLES
5.1 Consumable and Replacement Cycle
5.2 Replacing the Pad ASSY
5.3 Replacing the Pick Roller
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
The [Printer and Other Hardware] screen is displayed.
3. In the [Printer and Other Hardware] screen, double click the "Scanners and Cameras" icon.
The [Scanners and Cameras] screen is displayed.
1
2
3
4
5
CONTENTS
5.1 Consumable and Replacement Cycle (3)
1
INTRODUCTION
2
3
4
5
4. On "fi-5110Cdj" icon, right click and select [Properties] (for Windows Me, Windows XP),
or double click (for Windows 98, Windows 2000).
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
5.1 Consumable and Replacement Cycle
5.2 Replacing the Pad ASSY
5.3 Replacing the Pick Roller
6 TROUBLESHOOTING
The [fi-5110Cdj Properties] dialog box appears.
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
1
2
3
4
5
CONTENTS
5.1 Consumable and Replacement Cycle (4)
1
INTRODUCTION
2
3
4
5
5. Click the "Device Set" tab.
The following screen is displayed.
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
5.1 Consumable and Replacement Cycle
5.2 Replacing the Pad ASSY
5.3 Replacing the Pick Roller
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
You can confirm the following information in this panel:
❍
❍
❍
Total number of scans
Pad counter (approximate number of scans after resetting the pad counter)
Pick roller counter (approximate number of scans after resetting the Pick roller counter)
1
2
3
4
5
CONTENTS
5.1 Consumable and Replacement Cycle (5)
1
2
3
4
5
The following message may appear while you use the scanner:
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
5.1 Consumable and Replacement Cycle
5.2 Replacing the Pad ASSY
5.3 Replacing the Pick Roller
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
Replace consumables when this message is displayed.
After clicking the [Ignore] button, this message will disappear and scanning will continue.
Please replace the consumable as soon as possible.
As a default, this message appears again after 100 scans. If you do not wish this message to display, click
the [ this message not display again].
To stop scanning and replace the consumable, click the [Cancel] button.
Replacement information is given in the following:
Pad ASSY: See "5.2 Replacing the Pad ASSY"
Pick Roller: See "5.3 Replacing the Pick Roller"
1
2
3
4
5
CONTENTS
5.2 Replacing the Pad ASSY
1
2
1. Remove any documents on the ADF Paper Chute.
INTRODUCTION
2. Open the ADF by pulling the ADF Open Lever.
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
CAUTION
4 DAILY CARE
Be careful, the ADF may close and pinch your finger.
5 REPLACING CONSUMABLES
5.1 Consumable and Replacement Cycle
5.2 Replacing the Pad ASSY
5.3 Replacing the Pick Roller
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
3. Remove the Pad ASSY.
Press the knobs on both ends of the Pad ASSY, and pull the Pad ASSY upwards.
4. Attach the new Pad ASSY.
Hold both ends of the new Pad ASSY and attach it to its installation location.
When doing this, take care not to catch the metallic parts of the Pad ASSY.
8 OPTIONS
9 SCANNER SPECIFICATIONS
ATTENTION
Appendix
Make sure that the Pad ASSY is firmly attached. When the Pad ASSY is
not correctly attached, document jams or other feeding errors may occur.
5. Close the ADF.
You should hear the ADF click when it returns to its original position.
With the movie below, review the replacement procedure of the Pad ASSY:
1
2
CONTENTS
5.2 Replacing the Pad ASSY (2)
1
2
6. Reset the Pad Counter.
INTRODUCTION
When turning on the power, check that the scanner is connected to your PC.
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
Open the [Scanners and Cameras] from the [Control Panel] of your PC.
Open the [Properties] of [fi-5110Cdj] from the [Scanners and Cameras].
The [fi-5110Cdj Properties] dialogbox appears.
Click the "Device Set" tab.
5 REPLACING CONSUMABLES
5.1 Consumable and Replacement Cycle
The following screen is displayed.
5.2 Replacing the Pad ASSY
5.3 Replacing the Pick Roller
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
After clicking the [Clear] button beside "Pad" in "Page Counter", click the [OK] button.
The following screen is displayed.
Click the [OK] button.
This returns the pad counter to "0".
1
2
CONTENTS
5.3 Replacing the Pick Roller
1
2
3
1. Remove any documents on the ADF Paper Chute.
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
2. Remove the ADF paper chute.
3. Open the ADF by pulling the ADF Open Lever.
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
Caution
5 REPLACING CONSUMABLES
5.1 Consumable and Replacement Cycle
5.2 Replacing the Pad ASSY
5.3 Replacing the Pick Roller
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
Be careful, the ADF may close and pinch your finger.
4. Remove the Sheet Guide.
Grip the knobs on the sheet guide with your fingers, and lift it up to remove.
5. Rotate the Pick Roller Bushing in the direction of the arrow.
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
: Pick Roller Bushing
: Pick Roller Shaft
6. Remove the Pick Roller with its shaft.
Hold the left part of the shaft, and raise it to remove the shaft from the scanner while pulling the shaft
to the left.
Caution
The Pick roller Bushing is hard. Do not turn this bearing with your
fingernails.
Use a paper clip for turning the roller bushing if you can not rotate it with
your finger.
ATTENTION
If the area around the pick roller is dirty by paper-powder, it may cause a
scanning error. Remove the dirt using a dry cloth with dollop of Cleaner
F1.
* Do not use water, mild detergent or air-spray.
7. Remove the pick roller from its shaft.
Pull out the shaft from the pick roller while lifting up its tab.
Caution
If you push up the pick roller tab using your fingernail, it may hurt or get
chipped your fingernail. If you worry about that, push up the pick roller tab
using a paper clip.
1
2
3
CONTENTS
5.3 Replacing the Pick Roller (2)
1
2
3
8. Attach the new pick roller to the shaft.
INTRODUCTION
Insert the new pick roller aligning the protrusion with the slot on the pick roller.
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
: Pick Roller
Shaft
4 DAILY CARE
: Protusion
5 REPLACING CONSUMABLES
: Pick Roller
5.1 Consumable and Replacement Cycle
5.2 Replacing the Pad ASSY
5.3 Replacing the Pick Roller
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
ATTENTION
8 OPTIONS
9 SCANNER SPECIFICATIONS
Make sure that the Pick roller is completely attached. An incompletely
attached Pick roller might cause document jams or other feedings errors.
Appendix
9. Install the pick roller with its shaft to the scanner.
Attatch the Pick roller to the scanner in reverse order of the procedure for removing.
10. Rotate the roller bushing by rotating it in the direction of the arrow.
: Pick Roller Bushing
: Pick Roller Shaft
ATTENTION
Make sure that the Pick roller is completely attached. An incompletely
attached Pick roller might cause document jams or other feeding errors.
11. Attach the sheet guide to the scanner.
Pinch the knobs on the sheet guide and attach it to the scanner.
The sheet guide makes a clicking sound when the knobs fix into position.
ATTENTION
Make sure that the sheet guide is completely attached. Otherwise,
document jams or other feeding errors may occur.
12. Close the ADF.
You should hear the ADF click when it returns to its original position.
13. Attach the ADF paper chute.
With the movie below, review the replacement procedure of the Pick Roller.
1
2
3
CONTENTS
5.3 Replacing the Pick Roller(3)
1
2
3
14. Reset the pick counter.
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
When turning on the power, check that the scanner is connected to your PC.
Open the [Scanners and Cameras] from the [Control Panel] of your PC.
Open the [Properties] of [fi-5110Cdj] from the [Scanners and Cameras].
The [Properties of fi-5110Cdj] dialogbox is displayed.
4 DAILY CARE
5 REPLACING CONSUMABLES
Click the "Device Set" tab.
5.1 Consumable and Replacement Cycle
5.2 Replacing the Pad ASSY
The following panel appears.
5.3 Replacing the Pick Roller
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
After clicking the [Clear] button beside "Pick Roller" in "Page Counter", click the [OK] button.
The following panel appears.
Click the [OK] button.
This returns the pad counter to "0".
1
2
3
CONTENTS
6 TROUBLESHOOTING
This chapter describes how to remedy document jams, other trouble, items to check before contacting
the agent where you bought the scanner, and how to check device labels.
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
ATTENTION
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
6.1 Removing Jammed Documents
6.2 Error Indications in the Operator Panel
6.3 Remedying Typical Troubles
6.4 Items to Check Before Contacting the Agent
Where You Bought the Scanner
6.5 Checking Labels on the Scanner
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
About troubles that are not described here, and the details of the errors,
refer to the FUJITSU TWAIN32 Scanner Driver Help.
CONTENTS
6.1 Removing Jammed Documents
1
INTRODUCTION
2
3
If a document jam occured, follow the procedure below to remove the jammed documents.
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
CAUTION
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
●
4 DAILY CARE
●
5 REPLACING CONSUMABLES
●
6 TROUBLESHOOTING
6.1 Removing Jammed Documents
Take care not to get injured when removing jammed documents.
Be careful not to get neckties, necklaces, etc. entangled in the
scanner when removing the jammed documents.
The surface of the glass may become hot during operation. Take
care not to get burned.
1. Remove any documents on the ADF paper chute.
6.2 Error Indications in the Operator Panel
6.3 Remedying Typical Troubles
2. Open the ADF by pulling the ADF Open Lever.
6.4 Items to Check Before Contacting the Agent
Where You Bought the Scanner
6.5 Checking Labels on the Scanner
CAUTION
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
Be careful, the ADF may close and pinch your finger.
9 SCANNER SPECIFICATIONS
Appendix
3. Remove the jammed document.
ATTENTION
●
●
Staples, paper clips, etc. cause document jams. Be sure to fully
check the document and feed path, and remove any small metal
objects such as these.
Also, before you start scanning, be sure to remove any staples, clips,
etc. from the document.
Take care not to pull the metallic parts of the Pad ASSY when
removing jammed documents.
4. Close the ADF.
You should hear the ADF click when it returns to its original position.
ATTENTION
●
●
Make sure that the ADF is completely closed. When it is not
completely closed, document jams or feeding errors may occur.
When the scanning is completed or canceled, the documents might
remain inside the ADF even though any error message is not
displayed.
Follow the procedure below to remove the documetns remaining in
the ADF.
1. Remove all documents from the ADF paper chute.
2. Open the ADF by pulling the ADF open lever.
3. Remove the remaining documents.
4. Close the ADF.
With the movie below, review the procedure to remove jammed documents:
1
2
3
CONTENTS
6.1 Removing Jammed Documents(2)
1
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2
3
If a document jam or Multi Feed errors occur frequenlty, follow the procedures below .
1. Align the edges of the document sheets.
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
6.1 Removing Jammed Documents
6.2 Error Indications in the Operator Panel
6.3 Remedying Typical Troubles
6.4 Items to Check Before Contacting the Agent
Where You Bought the Scanner
2. Hold both the left and right sides of the document with both hands, and, as shown below, bend
the document, bring back and release one side of the stack.
6.5 Checking Labels on the Scanner
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
FRONT SIDE
3. The document edges will be slightly misaligned, as shown in the picture.
1
2
3
CONTENTS
6.1 Removing Jammed Documents(3)
1
INTRODUCTION
2
3
4. Load the documents into the ADF chute, as shown in the picture.
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
6.1 Removing Jammed Documents
6.2 Error Indications in the Operator Panel
6.3 Remedying Typical Troubles
6.4 Items to Check Before Contacting the Agent
Where You Bought the Scanner
6.5 Checking Labels on the Scanner
With the movie below, review the procedure to load documents when multi feed errors occur
frequently:
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
1
2
3
CONTENTS
6.2 Error Indications in the Operator Panel
1
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
2
When any error occurrs, the operator panel indicates "U" followed by a number for temporary errors or "E"
followed by a number for device alarms (permanent error).
Temporary errors can be resolved by the operator, but the device alarm requires recovery works by support
engineers.
When the Error Recovery Guide is installed on your PC, its window appears when Windows is started up. If
any error or device alarm occurred, this software displays information such as error names and error codes
regarding the error/alarm. Record the information and click [Details] on its window to learn detailed
information for trouble shooting.
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
6.1 Removing Jammed Documents
Temporary Errors :
A number appearing in alternation following the "U" refers to the following type of errors:
6.2 Error Indications in the Operator Panel
Indication
Meaning
U1
Paper Feed Error
U2
Multi Feed Error
U4
The ADF has been opened during scanning.
6.3 Remedying Typical Troubles
6.4 Items to Check Before Contacting the Agent
Where You Bought the Scanner
6.5 Checking Labels on the Scanner
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
HINT
Appendix
The Error Recover Guide is stored in Setup CD-ROM. When installing
the application software, refer to "2.1 Installing the Scanner Application"
in fi-5110C Getting Started.
1
2
CONTENTS
6.2 Error Indications in the Operator Panel (2)
1
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2
Device alarms:
A number appearing in alternation following the "E" refers to the following type of device alarms:
2 BASIC SCANNER OPERATIONS
Indication
Meaning
E2
Trouble in the optical system
(front).
E3
Trouble in the optical system (back).
E4
The motor fuse has blown out.
E6
Trouble with the Operator Panel.
6.2 Error Indications in the Operator Panel
E7
Trouble occurred with the EEPROM.
6.3 Remedying Typical Troubles
E9
An error in the image memory.
6.4 Items to Check Before Contacting the Agent
Where You Bought the Scanner
Ec
An alarm in the memory.
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
6.1 Removing Jammed Documents
6.5 Checking Labels on the Scanner
7 DOCUMENT SPECIFICATIONS FOR ADF
When you encounter any alarm, turn off and on the scanner. If the alarm is still displayed on the Function
No. display, contact the dealer where you purchased the scanner or an authorized FUJITSU scanner service
provider.
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
1
2
CONTENTS
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
6.3 Remedying Typical Troubles
This section describes troubles that may occur during scanning and how to
remedy that trouble. Before you ask for repair, check the following flowcharts. If
the remedies in these flowcharts do not solve the problem, check the items in "6.3
Items to Check Before Contacting the Agent Where You Bought the Scanner" and
then contact the agent where you bought the scanner or an authorized FUJITSU
service provider.
4 DAILY CARE
5 REPLACING CONSUMABLES
Scanner cannot be turned ON.
6 TROUBLESHOOTING
Indication on Function No. display goes out.
6.1 Removing Jammed Documents
The scanning does not start.
6.2 Error Indications in the Operator Panel
Quality of scanned pictures or photos is not satisfactory.
6.3 Remedying Typical Troubles
Quality of scanned text or lines is unsatisfactory.
6.4 Items to Check Before Contacting the Agent
Where You Bought the Scanner
Images are distorted or blurred.
6.5 Checking Labels on the Scanner
Vertical lines appear in the scanned image.
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
The Function No. display indicates alarm after the scanner is turned ON.
Multi feed errors occur frequently.
Pickup errors occur frequently.
Appendix
Paper jams occur frequently
The scanned images are elongated
There is a shadow on the top and bottom edge of the scanned images.
CONTENTS
Symptom 1 : Scanner cannot be turned ON.
Back
INTRODUCTION
Are power cable and AC adapter
No
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
Correctly connect power cable.
correctly connected?
Yes
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
You must use the AC adapter and
cable supplied with your scanner by
the manufacturer. Please get the
Are you using the correct AC cable and
AC adapter supplied with the scanner
from the manufacturer?
No
6 TROUBLESHOOTING
correct AC adapter and cable to
connect to your scanner.
6.1 Removing Jammed Documents
6.2 Error Indications in the Operator Panel
Yes
6.3 Remedying Typical Troubles
6.4 Items to Check Before Contacting the Agent
Where You Bought the Scanner
No
6.5 Checking Labels on the Scanner
7 DOCUMENT SPECIFICATIONS FOR ADF
Yes
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
Press power button.
Did you push the power button?
If you cannot solve the problem after
taking measures, check the items in
"6.4 Items to Check Before Contacting
the Agent Where You Bought the
Scanner" and contact the dealer or an
authorized FUJITSU service provider.
CONTENTS
Symptom 2F@Indication on Function No. display goes out.
Back
Does the display remain blank even
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
after you push any button on the
operator panel?
The scanner operation is normal.
No
Yes
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
Does the display remain blank even
after trunning ON the scanner again?
No
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
Yes
6.1 Removing Jammed Documents
6.2 Error Indications in the Operator Panel
6.3 Remedying Typical Troubles
6.4 Items to Check Before Contacting the Agent
Where You Bought the Scanner
6.5 Checking Labels on the Scanner
If you cannot solve the problem after
taking measures, check the items in
"6.4 Items to Check Before Contacting
the Agent Where You Bought the
Scanner" and contact the dealer or an
authorized FUJITSU service provider.
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
Scanner operation is normal.
CONTENTS
Symptom 3 : The scanning does not start.
Back
INTRODUCTION
chute.
the ADF paper chute?
No
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
Load document correctly on ADF paper
Is the document loaded correctly on
Yes
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
No
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
Close the ADF completely.
Is the ADF closed completely?
Yes
6.1 Removing Jammed Documents
6.2 Error Indications in the Operator Panel
6.3 Remedying Typical Troubles
Is the interface cable connected
correctly?
No
6.4 Items to Check Before Contacting the Agent
Where You Bought the Scanner
6.5 Checking Labels on the Scanner
Connect interface cable correctly. (*)
Yes
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Use a new interface cable and correctly
connect it.
Is the connector of the interface cable
broken?
Yes
Appendix
No
Does the scanning start after running
ON the scanner again?
The scanner operation is normal.
Yes
No
If you cannot solve the problem after
taking measures, check the items in
"6.4 Items to Check Before Contacting
the Agent Where You Bought the
Scanner" and contact the dealer or an
authorized FUJITSU service provider.
*) For details, refer to "Getting Started" 2.2 Connecting the scanner to your PC.
CONTENTS
Symptom 4 : Quality of scanned pictures or photos is not satisfactory.
Back
INTRODUCTION
No
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
Select halftoning or dithering on your
PC.
Did you select halftoning or dithering?
Yes
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
Are the upper/lower glasses inside the
ADF clean?
No
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
Yes
6.1 Removing Jammed Documents
6.2 Error Indications in the Operator Panel
6.3 Remedying Typical Troubles
6.4 Items to Check Before Contacting the Agent
Where You Bought the Scanner
6.5 Checking Labels on the Scanner
If you cannot solve the problem after
taking measures, check the items in
"6.4 Items to Check Before Contacting
the Agent Where You Bought the
Scanner" and contact the dealer or an
authorized FUJITSU service provider.
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
Clean dirty locations.
For details on how to clean dirty
locations, see "Chapter 4 DAILY CARE".
CONTENTS
Symptom 5 : Quality of scanned text or lines is unsatisfactory.
Back
INTRODUCTION
Are the upper/lower glasses inside the
ADF clean?
No
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
Yes
If you cannot solve the problem after
taking measures, check the items in
"6.4 Items to Check Before Contacting
the Agent Where You Bought the
6 TROUBLESHOOTING
6.1 Removing Jammed Documents
6.2 Error Indications in the Operator Panel
6.3 Remedying Typical Troubles
6.4 Items to Check Before Contacting the Agent
Where You Bought the Scanner
6.5 Checking Labels on the Scanner
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
Scanner" and contact the dealer or an
authorized FUJITSU service provider.
Clean dirty locations.
For details on how to clean dirty
locations, see "Chapter 4 DAILY CARE".
CONTENTS
Symptom 6 : Images are distorted or blurred.
Back
INTRODUCTION
Are the upper/lower glasses inside the
ADF clean?
No
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
Clean dirty locations.
For details on how to clean dirty
locations, see "Chapter 4 DAILY CARE".
Yes
Is the ADF pressed down or heavy
object placed on the ADF during
scanning?
Do not press down the ADF or place
heavy object on the ADF during
Yes
scanning.
No
6.1 Removing Jammed Documents
6.2 Error Indications in the Operator Panel
6.3 Remedying Typical Troubles
Yes
6.4 Items to Check Before Contacting the Agent
Where You Bought the Scanner
6.5 Checking Labels on the Scanner
Do not allow anything to cause the
scanner to vibrate while scanning.
Is something causing the scanner to
vibrate during scanning?
No
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Install the scanner on a flat, level
surface.
Is the scanner installed on a flat, level
surface?
No
Appendix
Yes
If you cannot solve the problem after
taking measures, check the items in
"6.4 Items to Check Before Contacting
the Agent Where You Bought the
Scanner" and contact the dealer or an
authorized FUJITSU service provider.
CONTENTS
Symptom 7 : Vertical lines appear in the scanned image.
Back
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
Clean the upper/lower glasses inside
the ADF.
For cleaning the glass, refer to "4.3
Do the lines appear on the same part of
images?
Yes
Cleaning the Inside of the Scanner".
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
No
Scan the documents with low
resolution settings.
Do the lines disappear on images with
low resolution settings?
Yes
6 TROUBLESHOOTING
6.1 Removing Jammed Documents
No
6.2 Error Indications in the Operator Panel
6.3 Remedying Typical Troubles
6.4 Items to Check Before Contacting the Agent
Where You Bought the Scanner
6.5 Checking Labels on the Scanner
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
If you cannot solve the problem after
taking measures, check the items in
"6.4 Items to Check Before Contacting
the Agent Where You Bought the
Scanner" and contact the dealer or an
authorized FUJITSU service provider.
CONTENTS
Symptom 8 : The Function No. display indicates alarm after the scanner is
turned ON.
Back
INTRODUCTION
Does the Function No. display indicate
1 NAMES AND FUNCTIONS OF PARTS
any alarm after turning ON the scanner
again?
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
Yes
If you cannot solve the problem after
taking measures, check the items in
"6.4 Items to Check Before Contacting
the Agent Where You Bought the
6.1 Removing Jammed Documents
Scanner" and contact the dealer or an
6.2 Error Indications in the Operator Panel
authorized FUJITSU service provider.
6.3 Remedying Typical Troubles
6.4 Items to Check Before Contacting the Agent
Where You Bought the Scanner
6.5 Checking Labels on the Scanner
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
The scanner operation is normal.
No
CONTENTS
Symptom 9 : Multi feed errors occur frequently.
Back
INTRODUCTION
Do the documents satisfy the
conditions described in "7.2 Document
1 NAMES AND FUNCTIONS OF PARTS
Quality"?
Use documents that satisfy the
requirements.
For details on requirements, see "7.2
No
Document Quality".
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
6.1 Removing Jammed Documents
6.2 Error Indications in the Operator Panel
Yes
When the multi feed detection is ON,
are the multi feed detection conditions
satisfied?
For details on multi feed, see "7.5 Multi
Satisfy the multi feed detection
conditions.
For details on multi feed, see "7.5 Multi
No
feed Detection Conditions".
feed Detection Conditions".
Yes
6.3 Remedying Typical Troubles
6.4 Items to Check Before Contacting the Agent
Where You Bought the Scanner
6.5 Checking Labels on the Scanner
Fan the document before loading, or
reduce the number of sheets of the
Was the document fanned before
loaded onto the ADF paper chute?
No
document.
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
Yes
9 SCANNER SPECIFICATIONS
Appendix
Fan the documents 3 or 4 times to
remove static electricity from the paper.
Have the documents just been printed
out on a copier or laser printer?
Yes
No
Reduce the number of sheets of the
document.
Is the document stack 5 mm or less?
No
Yes
Correctly install the consumables if
needed.
Are all the consumables (Pick roller
and Pad ASSY) installed correctly?
No
Yes
Clean the dirty consumables.
For details on how to clean the
Is any of consumables (Pick roller and
Pad ASSY) dirty?
consumables, see "4.3 Cleaning the
Yes
Inside of the Scanner"
No
Is any of consumables (Pick roller and
Pad ASSY) worn out? (Check the
consumable counter)
No
Replace the consumable, if needed. For
details on how to replace and attach
consumables, see "5 REPLACING
Yes
CONSUMABLES".
If you cannot solve the problem after
taking measures, check the items in
"6.4 Items to Check Before Contacting
the Agent Where You Bought the
Scanner" and contact the dealer or an
authorized FUJITSU service provider.
CONTENTS
Symptom 10 : Pickup errors occur frequently.
Back
Use documents that satisfy the
requirements.
For details on requirements, see "7.2
Do the documents satisfy the
INTRODUCTION
conditions described on "7.2 Document
1 NAMES AND FUNCTIONS OF PARTS
Quality"?
No
Document Quality".
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
Yes
Fan the document before loading, or
reduce the number of sheets of the
Was the document fanned before
loading on ADF paper chute?
No
document.
6 TROUBLESHOOTING
6.1 Removing Jammed Documents
Yes
6.2 Error Indications in the Operator Panel
6.3 Remedying Typical Troubles
6.4 Items to Check Before Contacting the Agent
Where You Bought the Scanner
Are all the consumables (Pick roller
and Pad ASSY) installed correctly?
No
6.5 Checking Labels on the Scanner
Correctly install the consumable(Pick
roller and Pad ASSY), if needed.
For details on how to install the
consumables, see "5 REPLACING
CONSUMABLES".
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
Yes
9 SCANNER SPECIFICATIONS
Appendix
Is any of consumables (Pick roller, Pad
ASSY) dirty?
Yes
Clean the dirty consumable.
For details on how to clean the
consumables, see "4 DAILY CARE".
No
Is any of consumables (Pick roller and
Pad ASSY) worn out? (Check the
consumable counter)
No
If you cannot solve the problem after
taking measures, check the items in
"6.4 Items to Check Before Contacting
the Agent Where You Bought the
Scanner" and contact the dealer or an
authorized FUJITSU service provider.
Replace the consumable, if needed.
For details on how to replace the
consumables, see "5 REPLACING
Yes
CONSUMABLES".
CONTENTS
Symptom 11 : Paper jams occur frequently
Back
INTRODUCTION
Do the documents satisfy the
conditions described in "7.2 Document
1 NAMES AND FUNCTIONS OF PARTS
Quality"?
Use the document that satisfy the
requirements.
For details on requirements, see "7.2
No
Document Quality".
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
Yes
Clean the ADF or remove debris from
4 DAILY CARE
5 REPLACING CONSUMABLES
Is there any debris in the ADF?
6 TROUBLESHOOTING
Yes
Scanner" .
6.1 Removing Jammed Documents
6.2 Error Indications in the Operator Panel
the ADF.
For details on how to clean the ADF,
see "4.3 Cleaning the Inside of the
No
6.3 Remedying Typical Troubles
6.4 Items to Check Before Contacting the Agent
Where You Bought the Scanner
6.5 Checking Labels on the Scanner
Correctly install the consumable (Pick
roller and Pad ASSY), if needed.
Are all the consumables (Pick roller
and Pad ASSY) installed correctly?
7 DOCUMENT SPECIFICATIONS FOR ADF
No
CONSUMABLES" .
8 OPTIONS
9 SCANNER SPECIFICATIONS
For details on how to install the
consumables, see "5 REPLACING
Yes
Appendix
Is any of consumables (Pick roller, Pad
ASSY) dirty?
Yes
Clean the dirty consumable.
For details on how to clean the
consumables, see "4 DAILY CARE".
No
Is any of consumables (Pick roller and
Pad ASSY) worn out? (Check the
consumable counter)
No
If you cannot solve the problem after
taking measures, check the items in
"6.4 Items to Check Before Contacting
the Agent Where You Bought the
Scanner" and contact the dealer or an
authorized FUJITSU service provider.
Replace the consumable, if needed.
For details on how to replace the
consumables, see "5 REPLACING
Yes
CONSUMABLES".
CONTENTS
Symptom 12 : The scanned images are elongated
Back
INTRODUCTION
Clean all the rollers.
For details on how to clean the rollers,
see "4.3 Cleaning the Inside of the
Have you cleaned all the rollers?
1 NAMES AND FUNCTIONS OF PARTS
No
Scanner".
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
Yes
Check the items in "6.4 Items to Check
4 DAILY CARE
Before Contacting the Agent Where
5 REPLACING CONSUMABLES
Have you adjusted the scan scale?
6 TROUBLESHOOTING
Yes
6.1 Removing Jammed Documents
6.2 Error Indications in the Operator Panel
No
6.3 Remedying Typical Troubles
6.4 Items to Check Before Contacting the Agent
Where You Bought the Scanner
6.5 Checking Labels on the Scanner
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
You Bought the Scanner" and contact
Set the scan scale.
Display the properties of the scanner
that you are using on "Scanners and
Cameras" in the control panel, then
adjust the scan scale.
the dealer or an authorized FUJITSU
service provider.
CONTENTS
Symptom 13 There is a shadow on the top and bottom edge of the
scanned images.
Back
Check the items in "6.4 Items to Check
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
Did you adjust the offset (starting
2 BASIC SCANNER OPERATIONS
position for scanning the document)?
No
4 DAILY CARE
6 TROUBLESHOOTING
6.1 Removing Jammed Documents
6.2 Error Indications in the Operator Panel
6.3 Remedying Typical Troubles
6.4 Items to Check Before Contacting the Agent
Where You Bought the Scanner
6.5 Checking Labels on the Scanner
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
You Bought the Scanner" and contact
Yes
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
5 REPLACING CONSUMABLES
Before Contacting the Agent Where
Adjust the offset.
On [Scanners and Cameras] in the
control panel, adjust the [Sub-scan
Setting] (in case there is a shadow in
the top edge) or adjust the [Bottom] (in
case there is a shadow in the bottom
edge).
the dealer or an authorized FUJITSU
service provider.
CONTENTS
6.4 Items to Check Before Contacting the Agent Where You Bought the
Scanner
INTRODUCTION
If you cannot solve the problem after checking the remedies in the Trouble shooting table, contact the dealer
where you bought the scanner or an authorized FUJITSU scanner service provider. Before you ask for repair
service, please collect the following information.
1 NAMES AND FUNCTIONS OF PARTS
Check items:
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
6.1 Removing Jammed Documents
6.2 Error Indications in the Operator Panel
6.3 Remedying Typical Troubles
6.4 Items to Check Before Contacting the Agent
Where You Bought the Scanner
6.5 Checking Labels on the Scanner
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
1. Model: fi-5110C
2. Serial No.F (Example) 000001
For details on the serial No., refer to section "6.4 Checking labels on the scanner".
3. Production date : (Example) 2004-08 (August, 2004)
For details on the production date, refer to section "6.4 Checking labels on the scanner".
Please print out the Check List as below, it will be displayed on a new window when you click the link, and fill
as much information as possible before contacting the agent.
The check list.
Items to check before contacting the dealer where you bought the scanner
Check the following items before you contact the dealer where you bought the scanner.
PRINT
General Details
Meaning
Findings
Model
fi-5110C
Serial No. (*)
(Example) 000001
Production date (*)
(Example) 2004-08 (August, 2004)
Date of purchase
January
1
, 2004
Symptom
Frequency of trouble
Total Page Count(ADF)
(**)
*Please confirm the necessary information in the product label. (Refer to 6.5 Checking labels on the scanner)
**Please confirm the "Scanners and Cameras" dialogbox . (Refer to 5.1 Consumable and Replacement Cycle)
Installation or PC connection issues
Trouble of connection to your PC
Meaning
OS
Displayed error
message
Findings
Windows XP
(For support engineers, please record the error message and send images of captured screen.)
Interface
(Example) USB 1.1
Feed system trouble
Meaning
Findings
Document type
Main purpose of use
Last cleaning date
Value of Consumable
counter
(Example) Pick roller set counter XXX
Displayed sign or
number on the
Operator panel at
trouble
Imaging system trouble
Meaning
Findings
Type and version of
scanner driver
Type of interface
controller
OS (Windows)
(Example) made by Adaptec SCSI Card 2940AU
Windows XP
Application software
(Example) ScandAll 21, Acrobat
Others
Meaning
Findings
Can you send us both the original document and the scanned images by e-mail or Fax?
PRINT
Yes
CONTENTS
6.5 Checking Labels on the Scanner
The following illustrations are samples of the product labels of fi-5110C Image Scanner.
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
6.1 Removing Jammed Documents
6.2 Error Indications in the Operator Panel
6.3 Remedying Typical Troubles
6.4 Items to Check Before Contacting the Agent
Where You Bought the Scanner
6.5 Checking Labels on the Scanner
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
The label position is as below.
CONTENTS
7 DOCUMENT SPECIFICATIONS FOR ADF
This chapter describes the required document size and paper quality for ensuring correct operation when
scanning documents on the ADF.
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
7.1 Document Size
7.2 Document Quality
7.3 Maximum Document Loading Capacity
7.4 Area not to be perforated
7.5 Multi feed Detection Conditions
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
CONTENTS
7.1 Document Size
The following shows the size of documents that can be scanned on the ADF.
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
7.1 Document Size
7.2 Document Quality
7.3 Maximum Document Loading Capacity
7.4 Area not to be perforated
7.5 Multi feed Detection Conditions
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
Maximum
A
216 (8.5 in)
Minimum
B
356 (14 in)
A
53 (2.1 in)
B
74 (2.9 in)
CONTENTS
7.2 Document Quality
1
2
Document Type
INTRODUCTION
The following paper types are recommended for document use:
1 NAMES AND FUNCTIONS OF PARTS
●
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
7.1 Document Size
●
Woodfree paper
Wood containing paper
When using documents of paper type other than the above, check whether or not the
document can be scanned by test-scanning a few sheets before executing the actual
document.
Document Thickness
Paper thickness is expressed by "paper weight." The following shows the paper weights
that can be used on this scanner:
●
52 g/m2 to 127 g/m2
Only paper weight of 127 g/m2 is acceptable for A8-size documents.
7.2 Document Quality
7.3 Maximum Document Loading Capacity
7.4 Area not to be perforated
7.5 Multi feed Detection Conditions
8 OPTIONS
Precautions
The following documents may not be scanned successfully:
●
●
9 SCANNER SPECIFICATIONS
Appendix
●
●
●
●
●
●
●
●
●
Documents of non-uniform thickness (e.g. envelopes)
Wrinkled or curled documents (See HINT on next page)
Folded or torn documents
Tracing paper
Coated paper
Carbon paper
Carbonless paper
Photosensitive paper
Perforated or punched documents
Documents that are not square or rectangular
Very thin documents
Do not use the following documents:
●
●
●
●
●
Paper-clipped or stapled documents
Documents on which the ink is still wet
Documents smaller than A8 (Portrait) in size
Documents wider than A4 or Letter size (216mm)
Documents other than paper such as fabric, metal foil, or transparencies
1
2
CONTENTS
7.2 Document Quality(2)
1
2
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
HINT
2 BASIC SCANNER OPERATIONS
●
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
●
4 DAILY CARE
When scanning semi-transparent documents, slide the [Brightness] bar to
"light" to avoid bleed through.
To prevent the rollers from becoming dirty, avoid scanning documents
containing large areas written or filled in pencil. If scanning of such
documents is unavoidable, clean the rollers frequently.
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
ATTENTION
7.1 Document Size
7.2 Document Quality
●
7.3 Maximum Document Loading Capacity
Carbonless paper contains chemical substances that may damage the Pad
ASSY or rollers (e.g. Pick roller) when documents are fed. Pay attention to
the following:
7.4 Area not to be perforated
Cleaning:
7.5 Multi feed Detection Conditions
If pick errors occur frequently, clean the Pad ASSY and Pick rollers.For
details on cleaning the Pad ASSY and Pick rollers, see "4.3 Cleaning
the Inside of the Scanner".
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
Replacing parts:
The service life of the Pad ASSY and Pick rollers is sometimes
shortened when scanning medium-grade paper documents.
●
When the manuscript of Wood containg paper is read, the life of a Pad
ASSY and a Pick roller may become short compared with the case where
the manuscript of Woodfree paper is read.
HINT
When using the ADF, the leading edge of all document sheets must be evenly
aligned. Make sure that curling at the leading edge is within the following
tolerances:
1
2
CONTENTS
7.3 Maximum Document Loading Capacity
The maximum number of sheets that can be loaded on the ADF paper chute is determined by the size and
weight of the document. The following graph shows the maximum document loading capacity of ADF
according to paper weight.
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
7.1 Document Size
7.2 Document Quality
7.3 Maximum Document Loading Capacity
7.4 Area not to be perforated
7.5 Multi feed Detection Conditions
Unit
Conversion
g/m2
52
64
75
80
90
104
127
lb
14
17
20
21
24
28
34
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
CONTENTS
7.4 Area not to be perforated
Document trouble might occur if there are punched holes in the shaded area in the following figure.
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
7.1 Document Size
7.2 Document Quality
7.3 Maximum Document Loading Capacity
7.4 Area not to be perforated
7.5 Multi feed Detection Conditions
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
CONTENTS
7.5 Multi feed Detection Conditions
1
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
2
There are three multi feed detection modes: document thickness, document length, and both document
thickness and length. The following conditions must be satisfied in each of these detection modes.
Detection by Document Thickness
Sheets of the same thickness shall be set in the ADF at a time.
●
●
●
●
●
6 TROUBLESHOOTING
Document thickness: 0.065 to 0.15mm
Printed area: 12% or less
No black printed areas are allowed at the center area (26 x 10mm) at the leading edge of the
document.
Punched holes are not allowed within 35mm of the vertical center line of the document.
The deviation in the amount of the light transmitted through background areas must not be less
than 10%.
7 DOCUMENT SPECIFICATIONS FOR ADF
7.1 Document Size
7.2 Document Quality
7.3 Maximum Document Loading Capacity
Detection by Document Length
Sheets of the same length shall be set in the ADF at a time.
●
●
7.4 Area not to be perforated
7.5 Multi feed Detection Conditions
8 OPTIONS
Detection by Document Thickness and Length
Sheets of the same thickness and length shall be set in the ADF at a time.
9 SCANNER SPECIFICATIONS
●
Appendix
Document length deviation: 1% or less
Punched holes are not allowed within 35mm of the vertical center line of the document.
●
●
●
●
●
Document thickness: 0.065 to 0.15mm
Document length deviation: 1% or less
Printed area: 12% or less
No black printed areas are allowed at the center area (26 x 10mm) at the leading edge of the
document.
Punched holes are not allowed within 35mm of the vertical center line of the document.
The deviation in the amount of the light transmitted through background areas must not be less
than 10%.
1
2
CONTENTS
7.5 Multi feed Detection Conditions(2)
1
2
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
HINT
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
The type of document and document conditions sometimes cause the
multi feed detection rate to drop.
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
7.1 Document Size
7.2 Document Quality
7.3 Maximum Document Loading Capacity
7.4 Area not to be perforated
7.5 Multi feed Detection Conditions
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
1
2
CONTENTS
8 OPTIONS
This chapter describes the options (sold separately) for fi-5110C Image Scanner.
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
8.1 Image Processing Software Option
9 SCANNER SPECIFICATIONS
Appendix
8.1 Image Processing Software Option
CONTENTS
fi-5110C Image Scanner option.
No.
INTRODUCTION
1
Name
Image Processing Software Option
Spec
PA43400-D72201
Description
For image processing (Binarizaiton)
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
8.1 Image Processing Software Option
9 SCANNER SPECIFICATIONS
Appendix
"Image Processing Software Option" is a software option for FUJITSU fi-series scanner to perform advanced
binalization processing using "FUJITSU TWAIN 32" scanner driver.
CONTENTS
9 SCANNER SPECIFICATIONS
This chapter lists the scanner specifications.
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
9.1 Basic Specifications
9.2 Installation Specifications
9.3 External Dimensions
APPENDIX
CONTENTS
9.1 Basic Specifications
1
No.
INTRODUCTION
2
Items
Specification
Remarks
1 NAMES AND FUNCTIONS OF PARTS
1
Scanner Type
ADF (Automatic Document Feeder)
-
2 BASIC SCANNER OPERATIONS
2
Image sensor
CCD x 2
Front / Back
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
3
Light source
White cold cathode fluorescent lamp x 2
Front / Back
4
Scanning
area
A8 size (Portrait)
ADF 127g/
m2 paper
A4 / Legal size
Long page scanning :
216 x 864mm
(8.50 x 34 in)
-
52 g/m2 to 127 g/m2
(14 to 34lb)
(Note (*1))
Binary
(monochrome)
Simplex: 15 sheets/min.
Duplex: 30 sides/min.
200 dpi
Color
Simplex: 15 sheets /min.
Duplex: 30 sides/min.
150 dpi
50 sheets
A4, 80 g/m2
(20lb)
(Note (*3))
4 DAILY CARE
Minimum
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
Maximum
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
5
Paper Weight
6
Scanning
Speed (A4
Portrait)
(Note (*2))
9 SCANNER SPECIFICATIONS
9.1 Basic Specifications
9.2 Installation Specifications
9.3 External Dimensions
APPENDIX
7
Capacity of ADF
(*1) For details, see "Chapter 7 DOCUMENT SPECIFICATIONS FOR ADF".
(*2) The scanning speed is the maximum speed of the scanner hardware. Software processing time such as
data transfer time is added to the actual scanning time.
(*3) The maximum stacking capacity varies according to the document thickness. For details, see "Chapter 7
DOCUMENT SPECIFICATIONS FOR ADF".
1
2
CONTENTS
9.1 Basic Specifications(2)
1
No.
INTRODUCTION
2
Items
8
Optical Resolution
9
Output resolution
Specification
Remarks
600 dpi
-
Binary (monochrome)
50 - 600 dpi
Scalable in 1 dpi
increments
Grayscale
50 - 600 dpi
Scalable in 1 dpi
increments
Color
50 - 600 dpi
Scalable in 1 dpi
increments
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
10
Halftone Patterns
Dither / error diffusion
-
7 DOCUMENT SPECIFICATIONS FOR ADF
11
Interface
USB 2.0/1.1
B type (note(*4))
8 OPTIONS
12
Other functions
JPEG compression
-
9 SCANNER SPECIFICATIONS
9.1 Basic Specifications
9.2 Installation Specifications
(*4) If you connect the scanner with USB 2.0, it is required that the USB port and the Hub are compliant with
USB 2.0. The scanning speed may slow down when you connect the scanner with USB 1.1. If your computer
has the compatible USB 2.0 port, please use it.)
9.3 External Dimensions
APPENDIX
1
2
CONTENTS
9.2 Installation Specifications
1
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
Dimensions (mm)
(Without ADF paper chute and Stacker)
Installation Space (mm)
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
Weight (kg)
Input power
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Specification
Items
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2
Power consumption
Depth
Width
Height
166 (6.54 in)
293.5 (11.55 in)
130 (5.19 in)
Depth
Width
Height
850 (33.46 in)
493.5 (19.43 in)
380 (14.96 in)
2.7 (5.9lb)
Voltage
100 to 120 VAC ±10%
220 to 240 VAC ±10%
Phases
Single-phase
Frequency
50/60 ±3 Hz
28 W or less
9.1 Basic Specifications
9.2 Installation Specifications
9.3 External Dimensions
ATTENTION
APPENDIX
Installation Space is the reference value of an installation space required to
read A4 manuscript.
1
2
CONTENTS
9.2 Installation Specifications(2)
1
2
Items
INTRODUCTION
Ambient condition
Specification
Device status
Operating
Not operating
Temperature
5 to 35 °C
(41 to 95°F)
-20 to 60 °C
(-4 to 140°F)
Humidity
20 to 80 %
8 to 95 %
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
Heat capacity
24.1 kcal / H or less
Shipping Weight (kg)
4.5 (9.8 lb)
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
9.1 Basic Specifications
9.2 Installation Specifications
9.3 External Dimensions
APPENDIX
1
2
CONTENTS
9.3 External Dimensions
The following shows the external dimensions of the fi-5110C:
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
9.1 Basic Specifications
9.2 Installation Specifications
9.3 External Dimensions
APPENDIX
CONTENTS
Appendix
The Appendix is structured as follows:
Appendix 1 Before using [Scan] button and [Send to] button
Appendix 2 Glossary
INTRODUCTION
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
Appendix 1 Before using "Scan" button and
"Send to" button
Appendix 2 Glossary
CONTENTS
Appendix 1 Before using [Scan] button and [Send to] button
1
INTRODUCTION
2
By setting the link of the application software to the [ Scan ] button and [ Send to ] button, you can launch the
linked application by simply pushing the button.
1 NAMES AND FUNCTIONS OF PARTS
1. Select [ Control panel ] from the [ Start ] menu.
2 BASIC SCANNER OPERATIONS
2. Select [ Properties ] from [ Scanner & Cameras ].
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
3. Select the [ Event ] tab.
4. Select an event. For Windows XP, select the event to be performed by the application from the
[ Select event ] menu.
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
Appendix 1 Before using "Scan" button and
"Send to" button
Appendix 2 Glossary
With this function, the next events can be selected.
●
Scan button (When pressing on [ Scan ] button)
●
Feeder loaded with paper (When document are loaded on the ADF)
●
Send to 1~9 (When pressing the [ Send to ] button)
1
2
CONTENTS
Appendix 1 Before using [Scan] button and [Send to] button (2)
1
INTRODUCTION
2
5. Select the application with its process, excuted by the event.
For Windows XP, click [Start this program] under [Actions] and select the application and process
from the menu.
1 NAMES AND FUNCTIONS OF PARTS
2 BASIC SCANNER OPERATIONS
3 SCANNING VARIOUS TYPES OF
DOCUMENTS
4 DAILY CARE
5 REPLACING CONSUMABLES
6 TROUBLESHOOTING
7 DOCUMENT SPECIFICATIONS FOR ADF
8 OPTIONS
9 SCANNER SPECIFICATIONS
Appendix
Appendix 1 Before using "Scan" button and
"Send to" button
Appendix 2 Glossary
6. Click the [ OK ] button.
HINT
When loading documents on the ADF, a pop-up screen may be displayed.
In order to avoid displaying the pop-up screen, select [ Feeder loaded with
paper ] at [ Select an event ] , and select [ Take no action] under
[ Actions ] and click the [ OK ] button.
(The displayed screen may differ slightly according to your OS.)
1
2