Samsung PDP-TELEVISION Installation manual

PDP-TELEVISION
(PLASMA DISPLAY PANEL)
Owner’s Instructions
Before operating the unit,
please read this manual thoroughly,
and retain it for future reference.
ON-SCREEN MENUS
Picture In Picture (PIP)
Energy Saving
TELETEXT (Option)
SRS TruSurround XT
Digital Natural Image engine
Register your product at www.samsung.com/global/register
Record your Model and Serial number here for future reference.
BN68-01171Q-00
01171Q-00Eng_Cover.indd
1
▪ Model _______________ ▪ Serial No. _______________
2007-02-12
ソタネト 5:22:19
User Instructions
 Screen Image retention
Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the
plasma monitor panel for more than 2 hours as it can cause screen image retention. This image
retention is also known as “screen burn”. To avoid such image retention, reduce the degree of
brightness and contrast of the screen when displaying a still image.
 Height
The PDP can normally operate only under 2000m in height. It might abnormally function at a place
over 2000m in height so do not install and operate there.
 Heat on the top of the PDP TV
The top side of the product may be hot after long period of use as heat dissipates from the panel
through the vent hole in the upper part of the product. This is normal and does not indicate any defect
or operation failure of the product. However, children should be prevented from touching the upper
part of the product.
 The product is making a ‘cracking’ noise.
A ‘cracking’ noise may occur when the product contracts or expands due to a change of surrounding
environment such as temperature or humidity. This is normal and not a defect of the unit.
 Cell Defects
The PDP uses a panel consisting of 1,230,000(SD-level) to 3,150,000(HD-level) pixels which require
sophisticated technology to produce. However, there may be few bright or dark pixels on the screen.
These pixels will have no impact on the performance of the product.
 Avoid operating the TV at temperatures below 5°C(41°F)
 A still image displayed too long may cause permanent damage to the PDP Panel.
Watching the PDP TV in 4:3 format for a long period of time may leave traces
of borders displayed on the left, right and centre of the screen caused by the
difference of light emission on the screen. Playing a DVD or a game console
may cause similar effect to the screen. Damages caused by the above effect are
not covered by the Warranty.
 Afterimage on the Screen.
Displaying still images from Video games and PC for longer than a certain period of time may
produce partial afterimages. To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when
displaying still images.
 Warranty
- Warranty does not cover any damage caused by image retention.
- Burn-in is not covered by the warranty.
 Installation
Be sure to contact an authorized service centre, when installing your set in a location with heavy
dust, high or low temperatures, high humidity, chemical substance and where it operates continually
such as the airport, the train station etc. Failure to do so may cause a serious damage to your set.
© 2007 Samsung Electronics Co., Ltd. All rights reserved.
English - 2
BN68-01171P-00Eng_0223.indd
2
2007-02-23
ソタネト 1:43:09
Contents
General Information
Function Description
User Instructions ............................................. 2
Checking Parts................................................ 4
Using the Stand-Base ..................................... 4
Control Panel ................................................. 5
Connection Panel............................................ 6
Viewing the Remote Control (PS42Q91H/
PS42Q92H/PS50Q91H/PS50Q92H) .............. 8
 Viewing the Remote Control (PS42C91H/
PS50C91H) ..................................................... 9
 Time Features ............................................... 25
 Language / Blue Screen / Melody /
Light Effect / Energy Saving /
HDMI Black Level ......................................... 26
 Using the Game Mode .................................. 27
 Wall- mount adjustment (Sold separately) .... 28
 Viewing the Picture in Picture (PIP) .............. 29
 Screen Burn Protection ................................. 30






PC Display
Operation






Switching Your Television On and Off ........... 10
Viewing the Menus ........................................ 11
Freezing the Current Picture ......................... 11
Plug & Play Feature ...................................... 12
Viewing an External Signal Sources ............. 13
Editing Device Names................................... 14
Channel Control







Storing Channels Automatically .................... 14
Storing Channels Manually ........................... 15
Adding / Locking Channels ........................... 16
Sorting the Stored Channels ......................... 17
Assigning Names to Channels ...................... 17
Fine Tuning Channel Reception.................... 18
LNA (Low Noise Amplifier) (PS42Q91H/
PS42Q92H/PS50Q91H/PS50Q92H) ............ 18
Picture Control






Changing the Picture Standard ..................... 19
Customizing the Picture Settings .................. 19
Configuring Detailed Settings on the Picture .. 20
Selecting the Picture Size ............................. 21
Selecting the Screen Mode ........................... 21
Digital NR / Active Colour / DNIe /
Movie Plus .................................................... 22
 Setting up Your PC Software
(Based on Windows XP) ............................... 31
 Input Mode (PC)............................................ 32
 Setting the PC ............................................... 33
 Setting the Home Theatre PC ....................... 34
About Anynet+ (PS42Q91H/PS42Q92H/PS50Q91H/PS50Q92H)
What is Anynet+? .......................................... 35
Connecting Anynet+ Devices ........................ 35
Setting Up Anynet+ ....................................... 36
Scanning and Switching between Anynet+
Devices ......................................................... 36
 Recording...................................................... 37
 Listening through a Receiver ........................ 38
 Check Points before Requesting Service ..... 38




Appendix
 Teletext Feature (depending on the model) .. 39
 Installing the Wall Mount Kit .......................... 41
 Setting Up Your Remote Control
(PS42Q91H/PS42Q92H/PS50Q91H/
PS50Q92H)................................................... 42
 How to assemble the Stand-Base
(depending on the model) ............................. 47
 Troubleshooting ............................................ 47
 Specifications ................................................ 48
Sound Control
 Sound Features ............................................ 23
 Selecting the Sound Mode
(depending on the model) ............................. 24
☛
➢
Important
Note
Symbols
Press
English - 3
BN68-01171P-00Eng_0223.indd
3
2007-02-23
ソタネト 1:43:09
Checking Parts
Owner’s Instructions
Remote Control/
AAA Batteries
Power Cord
Warranty Card/
Registration Card/
Safety Guide Manual
Cover-Bottom / Screws (2ea)
(Refer to page 47)
Ferrite Core for Power Cord/
S-Video Cable
Cloth-Clean
Ferrite Core for
Headphones Cable/
Power Cord
Sold Separately
S-Video Cable
Antenna Cable
Component Cables
Audio Cables
Video Cable
PC Cable
Scart Cable
PC Audio Cable
HDMI Cable
HDMI/DVI Cable
Core (Power Cord, Headphones Cable, S-Video Cable)
➢ Ferrite
The ferrite core is used to shield the cable from interference.
When connecting a cable, open the ferrite core and clip it
around the cable.
Using the Stand-Base
➢
 Two or more people should carry
the PDP. Never lay the PDP on the
floor because of possible damage
to the screen. Always keep the
PDP upright.
 The PDP can rotate 20 degrees in
right and left directions.
-20° ~ 20°
English - 4
BN68-01171P-00Eng_0223.indd
4
2007-02-23
ソタネト 1:43:12
Control Panel
Front (or Side) Panel
Speaker
➢ The product colour and shape may vary depending on the model.
1 SOURCE
Displays a menu of all of the available input
sources (TV, Ext.1, Ext.2, AV, S-Video,
Component, PC, HDMI1, HDMI2, and HDMI3).
HDMI3 mode is available only in
PS42Q91H/PS42Q92H/PS50Q91H/
PS50Q92H models.
4
C/P.
Press to change channels. In the on-screen
menu, use the
C/P.
buttons as
you use the ▲ and ▼ buttons on the remote
control.
5
(ENTER)
Press to confirm a selection.
6
(Power) button
Press to turn the TV on and off.
➢
2 MENU
Press to see the on-screen menu of your TV’s
features.
3 +−
Press to increase or decrease the volume.
In the on-screen menu, use the +−
buttons as you use the ◄ and ► buttons on
the remote control.
Power Indicator
− Power Off: Blue
− Power On: Off
Remote Control Sensor
Aim the remote control towards this spot on
the TV.
English - 5
BN68-01171P-00Eng_0223.indd
5
2007-02-23
ソタネト 1:43:14
Connection Panel
Side Panel
1
2
or
3
➢ The product colour and shape may vary depending on the model.
1 HDMI IN 3 (PS42Q91H/PS42Q92H/
PS50Q91H/PS50Q92H)
Connect to the HDMI jack of a device with
HDMI output.
2 S-VIDEO or VIDEO / AUDIO L/R
Video (S-Video or Video) and audio inputs for
external devices, such as a camcorder or VCR.
3 Headphones jack
You can connect a set of headphones if you
wish to watch a television programme without
disturbing the other people in the room.
Prolonged use of headphones at a high
volume may damage your hearing.
➢
Rear Panel
1
or
8
Cable Television
Network
5
or
2
3
4
6
7
➢ The product colour and shape may vary depending on the model.
☛
 Whenever you connect an audio or video system to your set, ensure that all elements are
switched off.
 When connecting an external device, match the colour of the connection terminal to the cable.
Continued...
English - 6
BN68-01171P-00Eng_0223.indd
6
2007-02-23
ソタネト 1:43:18
1 POWER IN
Connect the supplied power cord.
2 Connecting external Audio Devices
Connect RCA audio signals from the TV to an
external source, such as Audio equipment.
3 EXT 1, EXT 2
Inputs or outputs for external devices, such as
VCR, DVD, video game device or video disc
players.
8 ANT IN
75Ω Coaxial connector for Aerial/Cable
Network.
Supported modes for HDMI and Component
HDMI/DVI 50Hz
HDMI/DVI 60Hz
Component
480i 480p 576i 576p 720p 1080i
X
O
X
O
O
O
X
O
X
X
O
O
O
O
O
O
O
O
Input/Output Specification
Connector
EXT 1
EXT 2
Input
Output
Video Audio(L/R) RGB Video + Audio(L/R)
Only TV or DTV
✔
✔
✔
output is available.
Output you can
✔
✔
choose.
4 COMPONENT IN
Audio (AUDIO L/R) and video (Y/PB/PR) inputs
for Component.
5 SERVICE
− Connector for service.
− Connect the serial jack between the electromotion wall mount bracket and your TV
when you want to adjust the TV viewing
angle using your remote control.
6 PC IN / AUDIO
Connect to the video and audio output jack on
your PC.
7 HDMI IN 1, HDMI IN 2
− Connect to the HDMI jack of a device with
HDMI output. These inputs can also be used
as a DVI connection with separate analog
audio inputs. An optional HDMI/DVI cable
will be necessary to make this connection.
When using the optional HDMI/DVI adapter,
the DVI analog audio inputs on your TV
allow you to receive left and right audio from
your DVI device. (Not compatible with PC)
− When connecting this product via HDMI or
DVI to a Set Top Box, DVD Player or Games
Console etc, make sure that it has been
set to a compatible video output mode as
shown in the table below. Failure to observe
this may result in picture distortion, image
breakup or no picture.
− Do not attempt to connect the HDMI/DVI
connector to a PC or Laptop Graphics Card.
(This will result in a blank screen being
displayed)
DVI IN (HDMI 2) AUDIO L/R
DVI audio outputs for external devices.
English - 7
BN68-01171P-00Eng_0223.indd
7
2007-02-23
ソタネト 1:43:19
Viewing the Remote Control (PS42Q91H/PS42Q92H/PS50Q91H/PS50Q92H)
➢
 This is a special remote control for the visually impaired persons, and has Braille points on the
Power, Channel, Volume, STOP, and PLAY/PAUSE buttons.
 The performance of the remote control may be affected by bright light.
1 POWER button (turns the TV
on and off)
2 Number buttons for direct
channel access
3 One/Two-digit channel
selection
4 Channel control button
(Refer to page 16)
5 Selects the TV mode directly
6
Volume increase
Volume decrease
7 Temporary sound switch-off
8 Displays the main on-screen
menu
9 Returns to the previous
menu
0 Sound effect selection (Refer
to page 23)
! Picture effect selection
(Refer to page 19)
# Picture-In-Picture On/Off
$ Sound mode selection
% TruSurround XT mode
button
^ Remote control setup
& Selects a target device to be
controlled by the Samsung
remote control (TV, DVD,
STB, CABLE, VCR)
* Press to backlight the VOL,
CH, and the active source
button (TV, DVD, CABLE,
STB, VCR) on the remote.
( Available source selection
) Previous channel
a Automatic Power-off
b Records for Live
Broadcasting
c VCR/DVD Function (Rewind,
Stop, Play/Pause, Fast/
Forward
d
Next channel
Previous channel
e Exit the on-screen menu
f Control the cursor in the
menu
g Use to see information on
the current broadcast
h Runs the Anynet+ view
functions and sets up
Anynet+ devices.
i Picture freeze
j Picture size selection
l Select the channel of sub
picture (PIP)
n If your remote control is not
functioning properly, take
out the batteries and press
the reset button for about
2~3 seconds. Re-insert the
batteries and try using the
remote control again.
Teletext Functions
(Refer to page 39)
5 Exit from the teletext display
(depending on the model)
8 Teletext index
@ Teletext display/mix both
teletext information and the
normal broadcast
# Teletext hold
( Teletext mode selection
(LIST/FLOF)
) Teletext sub page
d P :Teletext next page
P :Teletext previous page
e Teletext cancel
g Teletext reveal
k Fastext topic selection
m Teletext size
o Teletext store
Continued...
English - 8
BN68-01171P-00Eng_0223.indd
8
2007-02-23
ソタネト 1:43:20
Viewing the Remote Control (PS42C91H/PS50C91H)
➢
 This is a special remote control for the visually impaired persons, and has Braille points on the
POWER, Volume and Channel buttons.
 The performance of the remote control may be affected by bright light.
1 POWER button
(turns the TV on and off)
2 Number buttons for direct
channel access
3 One/Two-digit channel
selection
4 Channel control button
(Refer to page 16)
5 Selects the TV mode directly
6
:Volume increase
:Volume decrease
7 Displays the main on-screen
menu
8 Temporary sound switch-off
9 Use to see information on
the current broadcast
0 Returns to the previous
menu
! Sound effect selection
(Refer to page 23)
@ Picture effect selection
(Refer to page 19)
# Adjusts screen brightness to
save energy.
$ Sound mode selection
% Picture-In-Picture Off/On
^ TruSurround XT mode
button
& Available source selection
* Previous channel
( Automatic Power-off
) Selects the HDMI mode
directly.
a
:Next channel
:Previous channel
b Exit the on-screen menu
c Change confirmation
d Move to the required menu
option / Adjust an option
value respectively
f Picture freeze
g Picture size selection
i Sub picture (PIP) channel
selection
j Sub picture (PIP) source
selection
k Sub picture (PIP) location
selection
Teletext Functions
(Refer to page 39)
5 Exit from the teletext display
(depending on the model)
7 Teletext index
9 Teletext reveal
% Teletext hold
& Teletext mode selection
(LIST/FLOF)
* Teletext sub page
a P :Teletext next page
P :Teletext previous page
b Teletext cancel
e Teletext display/mix both
teletext information and the
normal broadcast
h Fastext topic selection
j Teletext store
k Teletext size
Continued...
English - 9
BN68-01171P-00Eng_0223.indd
9
2007-02-23
ソタネト 1:43:22
Installing Batteries in the Remote Control
1
2
3
Lift the cover at the back of the remote control upward as
shown in the figure.
Install two AAA size batteries.
 Make sure to match the “+” and “–” ends of the
batteries with the diagram inside the compartment.
 Do not mix battery types, i.e. alkaline and manganese.
Close the cover as shown in the figure.
Remove the batteries and store them in a cool and dry
place if you won’t be using the remote control for a long
time. The remote control can be used up to about 23 feet
from the TV. (Assuming typical TV usage, the batteries last
for about one year.)
➢
➢
remote control doesn’t work! Check the following:
➢ If1.the
Is the TV power on?
2. Are the plus and minus ends of the batteries reversed?
3. Are the batteries drained?
4. Is there a power cut, or is the power cord unplugged?
5. Is there a special fluorescent light or a neon sign nearby?
Switching Your Television On and Off
The main lead is attached to the rear of the television.
1 Plug the main lead into an appropriate socket.
The main voltage is indicated on the rear of the television and the frequency is 50 or 60Hz.
2 Press the (Power) button (On/Off) on the front of the television or press the POWER button on the
remote control to switch the television on. The programme that you were watching last is re-selected
automatically. If you have not yet stored any channels, no clear picture appears. Refer to “Storing
Channels Automatically” on page 14 or “Storing Channels Manually” on page 15.
If the television is initially powered on, several basic customer settings proceed automatically.
Refer to “Plug & Play Feature” on page 12.
3 To switch the television off, press the (Power) button (On/Off) on the front of the television or press
the POWER button on the remote control.
4 To switch the TV on, press the (Power) button (On/Off) on the front of the TV or press the POWER
button or number buttons on the remote control.
➢
➢
English - 10
BN68-01171P-00Eng_0223.indd
10
2007-02-23
ソタネト 1:43:23
Viewing the Menus
1
2
3
4
5
Press the MENU button.
The main menu is displayed on the screen.
Its left side has five icons: Picture, Sound, Channel, Setup,
and Input.
Press the ▲ or ▼ button to select one of the icons.
Press the ENTER button to access the icon’s sub-menu.
Press the ▲ or ▼ button to move to items in the menu.
Press the ENTER button to enter items in the menu.
Press the ▲/▼/◄/► button to change the selected items.
Press the RETURN button to return to the previous menu.
Press the EXIT button to exit from the menu.
TV
Picture
Mode
: Dynamic
Contrast
Brightness
Sharpness
Colour
Tint
G 50
Colour Tone
: Cool1
Detailed Settings

100
45
75
55
R 50


 More
Move
Enter
Exit
illustration for remote control and OSD (On Screen
➢ The
Display) shown in this manual has been created based on the
PS42Q91H model. Even though the configuration is different
from your model, the operation method is the same as in the
illustration.
Freezing the Current Picture
You can freeze the picture when watching a television
programme simply by pressing the “STILL” button. To return to
normal viewing, press it again.
This function will automatically cancel five minutes later.
➢
English - 11
BN68-01171P-00Eng_0223.indd
11
2007-02-23
ソタネト 1:43:24
Plug & Play Feature
When the television is initially powered on, several basic
customer settings proceed automatically and subsequently.
The following settings are available.
If you accidentally select the wrong country for your TV, the
characters on the screen may be wrongly displayed.
1 If the television is in standby mode, press the POWER button
on the remote control. The message Start Plug & Play is
displayed. Press the ENTER button.
2 The Language menu will automatically appear after several
seconds.
3 Select the appropriate language by pressing the ▲ or ▼ button.
Press the ENTER button. The message Select Home Mode
when installing this TV at home. is displayed.
4 Press the ◄ or ► button to select Shop or Home, then press
the ENTER button. The message to check the connected status
of the antenna is displayed.
The default selection is Home.
We recommend setting the TV to Home mode for the best
picture in your home environment.
Shop mode is only intended for use in retail environments.
If the unit is accidentally set to Shop mode, and you want to
return to Dynamic (Home) mode, press the Volume button
and then hold down the MENU button for five seconds on
the TV panel.
5 Make sure that the antenna is connected to the TV.
Press the ENTER button. The Country menu is displayed.
6 Select your country or area by pressing the ▲ or ▼ button.
Press the ENTER button. The menu to select channels is
displayed.
7 To start channel store, press the ENTER button.
The search will end automatically. The TV will begin memorizing
all of the available channels.
Press the ENTER button to set the clock.
8 Press the ◄/►/ENTER button to select Month, Day, Year,
Hour, or Minute. Set these by pressing the ▲ or ▼ button.
You can set the Month, Day, Year, Hour, or Minute
directly by pressing the numeric buttons on the remote
control.
9 Press the ENTER button to confirm your setting.
The message Enjoy your viewing is displayed.
When you have finished, press the ENTER button.
Even if the ENTER button is not pressed, the message will
automatically disappear after several seconds.
Plug & Play
☛
➢
➢
➢
➢
Start Plug & Play.
OK
Enter
Plug & Play
English
Deutsch
Français
Italiano
▼
Language
Move
Enter
Skip
Plug & Play
Select Home Mode
when installing this TV at home.
Home
Shop
Move
Enter
Skip
Plug & Play
Check antenna input.
OK
Enter
Skip
Plug & Play
Belgium
France
Germany
Italy
▼
Country
Move
Enter
➢
Skip
Plug & Play
Auto Store
P 1
C
--
40 MHz
0 %
Start
➢
➢ Plug & Play feature is available in the TV mode only.
Return
Enter
Skip
Plug & Play
Clock Set
Month Day

01

01
Adjust
Year
Hour
Minute
2007
12
00
Move
Enter
Enjoy your viewing
Continued...
OK
English - 12
BN68-01171P-00Eng_0223.indd
12
2007-02-23
ソタネト 1:43:26
If you want to reset this feature …
1 Press the MENU button to display the menu.
2 Press the ▲ or ▼ button to select Setup, then press the
ENTER button.
3 Press the ENTER button again to select Plug & Play.
The message Start Plug & Play is displayed.
TV
Setup
Plug & Play
Language
Time
Game Mode
Blue Screen
Melody
PC
Home Theatre PC
Light Effect
 More
Move
: English
: Off
: Off
: Off
: Off
: Off
Enter









Return
Viewing an External Signal Sources
You can switch between viewing signals from connected
equipment, such as a VCR, DVD, Set-Top Box, and the TV
source (broadcast or cable).
1 Press the MENU button to display the menu.
2 Press the ▲ or ▼ button to select Input, then press the ENTER
button.
3 Press the ENTER button again to select Source List.
4 Press the ▲ or ▼ button to select the signal source, then press
the ENTER button.
Available signal sources: TV, Ext.1, Ext.2, AV, S-Video,
Component, PC, HDMI1, HDMI2, HDMI3
HDMI3 mode is available only in PS42Q91H/PS42Q92H/
PS50Q91H/PS50Q92H models.
➢
TV
Input
Source List
Edit Name
Anynet+
Move
TV
: TV



Enter
Return
Source List
TV
Ext.1
Ext.2
AV
S-Video
Component
PC
HDMI1
HDMI2
HDMI3
Move
: −−−−
: −−−−
: −−−−
: −−−−
: −−−−
: −−−−
: −−−−
: −−−−
: −−−−
Enter
Return
can select these options simply by pressing the SOURCE
➢ You
button on the remote control.
watch television programme again, press the TV button and
➢ To
select the channel number required.
English - 13
BN68-01171P-00Eng_0223.indd
13
2007-02-23
ソタネト 1:43:27
Editing Device Names
You can give a name to the external source.
1 Press the MENU button to display the menu.
2 Press the ▲ or ▼ button to select Input, then press the ENTER
button.
3 Press the ▲ or ▼ button to select Edit Name, then press the
ENTER button.
4 Press the ▲ or ▼ button to select the external source to be
edited, then press the ENTER button.
5 Select the required device by pressing ▲ or ▼, then press the
ENTER button.
Available device names: VCR, DVD, D-VHS, Cable STB, HD
STB, Satellite STB, AV Receiver, DVD Receiver, Game,
Camcorder, DVD Combo, DHR (DVD HDD Recorder), PC.
6 Press the EXIT button to exit.
HDMI3 mode is available only in PS42Q91H/PS42Q92H/
PS50Q91H/PS50Q92H models.
Input
TV
: TV



Enter
Return
Source List
Edit Name
Anynet+
Move
TV
Edit Name
: −−−−−−−−
: −−−− VCR
: −−−− DVD
: −−−−D-VHS
: −−−−
Cable STB
: −−−−
HD STB
: −−−−
Satellite STB
: −−−− ▼
: −−−−
Ext.1
Ext.2
AV
S-Video
Component
PC
HDMI1
HDMI2
HDMI3
➢
Move
Enter
Return
Storing Channels Automatically
You can scan for the frequency ranges available to you
(availability depends on your country).
Automatically allocated programme numbers may not
correspond to actual or desired programme numbers. However
you can sort numbers manually and clear any channels you do
not wish to watch.
1 Press the MENU button to display the menu.
2 Press the ▲ or ▼ button to select Channel, then press the
ENTER button.
3 Press the ENTER button again. The available countries are
listed.
4 Select your country by pressing the ▲ or ▼ button, then press
the ENTER button.
5 Press the ▲ or ▼ button to select Auto Store, then press the
ENTER button.
6 Press the ENTER button again to start the search.
The search will end automatically.
To stop the search before it has finished, press the MENU
or the ENTER button.
TV
Channel
Belgium
Country
: Belgium
Auto Store
France
Manual Store
Germany
Channel Manager
Italy
Sort
Netherlands
Name
Spain
Fine Tune
▼
LNA
: Off
Move
Enter
TV
Return
Channel
Country
: Belgium
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
LNA
: Off
➢
Move
Enter








Return
Auto Store
P 1
C
--
40 MHz
0 %
Start
Enter
Return
English - 14
BN68-01171P-00Eng_0223.indd
14
2007-02-23
ソタネト 1:43:28
Storing Channels Manually
You can store television channels, including those received via
cable networks.
When storing channels manually, you can choose:
 Whether or not to store each of the channels found.
 The programme number of each stored channel which you wish
to identify.
1 Press the MENU button to display the menu.
2 Press the ▲ or ▼ button to select Channel, then press the
ENTER button.
3 Press the ▲ or ▼ button to select Manual Store, then press
the ENTER button.
4 Select the required option by pressing the ▲ or ▼ button, then
press the ENTER button.
5 When you are satisfied with your setting, press the ENTER
button.
6 Press the EXIT button to exit.
TV
Channel
Country
: Belgium
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
LNA
: Off
Move
TV
Enter








Return
Manual Store
Programme
Colour System
Sound System
Channel
Search
Store
:P 1
: Auto
: BG
4
:C
: 63 MHz
:?


 Programme (Programme number to be assigned to a channel)
Move
Enter
Return
− Press the ▲ or ▼ button until you find the correct number.
You can also select the channel number directly by
pressing the numeric buttons (0~9).
 Colour System: Auto/PAL/SECAM/NTSC4.43
− Press the ▲ or ▼ button to select the required colour standard.
 Sound System: BG/DK/I/L
− Press the ▲ or ▼ button to select the required sound standard.
 Channel (When you know the number of the channel to be stored)
− Press the ▲ or ▼ button to select C (Air channel) or S (Cable channel).
− Press the ► button, then press the ▲ or ▼ button to select the required number.
You can also select the channel number directly by pressing the numeric buttons (0~9).
If there is abnormal sound or no sound, re-select the sound standard required.
 Search (When you do not know the channel numbers)
− Press the ▲ or ▼ button to start the search.
− The tuner scans the frequency range until the first channel or the channel that you selected is
received on the screen.
 Store (When you store the channel and associated programme number)
− Set to OK by pressing the ENTER button.
➢
➢
➢
mode
☛ Channel
 P (Programme mode): When completing tuning, the broadcasting stations in your area have
been assigned to position numbers from P00 to P99. You can select a channel by entering the
position number in this mode.
 C (Air channel mode): You can select a channel by entering the assigned number to each air
broadcasting station in this mode.
 S (Cable channel mode): You can select a channel by entering the assigned number for each
cable channel in this mode.
English - 15
BN68-01171P-00Eng_0223.indd
15
2007-02-23
ソタネト 1:43:29
Adding / Locking Channels
Using the Channel Manager, you can conveniently lock or add
channels.
1 Press the MENU button to display the menu.
2 Press the ▲ or ▼ button to select Channel, then press the
ENTER button.
3 Press the ▲ or ▼ button to select Channel Manager, then
press the ENTER button.
 Adding channels
Using the Channel List, you can add channels.
4
5
Select Channel List by pressing the ENTER button.
Move to the ( ) field by pressing the ▲/▼/◄/► buttons,
select a channel to be added, and press the ENTER button to
add the channel.
If you press the ENTER button again, the ( ) symbol next
to the channel disappears and the channel is not added.
TV
Channel
Country
: Belgium
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
LNA
: Off
Move
TV
Enter








Return
Channel Manager
Channel List
Child Lock
: Off

➢
 Locking channels
This feature allows you to prevent unauthorized users, such as
children, from watching unsuitable programmes by muting out
video and audio.
6
Press the ▲ or ▼ button to select Child Lock, then press the ENTER
button.
7 Select On by pressing the ▲ or ▼ button, then press the ENTER
button.
8 Press the ▲ or ▼ button to select Channel List, then press the
ENTER button.
9 Move to the ( ) field by pressing the ▲/▼/◄/► buttons, select a
channel to be locked, and press the ENTER button.
If you press the ENTER button again, the ( ) symbol next to the
channel disappears and the channel lock is canceled.
A blue screen is displayed when Child Lock is activated.
10 Press the EXIT button to exit.
➢
➢
Move
Enter
Return
Channel List
P 1 C4
1 / 10
Prog.
0
1
2
3
4
5
6
7
8
9
▲
C -C4
C 24
C2
C5
C 80
C7
C 36
C 52
C 11
Add
Move
Page
▼
Lock
Enter
Return
can select these options simply by pressing the CH LIST
➢ You
button on the remote control.
English - 16
BN68-01171P-00Eng_0223.indd
16
2007-02-23
ソタネト 1:43:30
Sorting the Stored Channels
This operation allows you to change the programme numbers
of the stored channels.
This operation may be necessary after using the auto store.
1 Press the MENU button to display the menu.
2 Press the ▲ or ▼ button to select Channel, then press the
ENTER button.
3 Press the ▲ or ▼ button to select Sort, then press the ENTER
button.
4 Select the channel that you wish to move by pressing the ▲ or
▼ button, then press the ENTER button.
5 Select the number of the programme to which the channel is to
be moved by pressing the ▲ or ▼ button.
Press the ENTER button. The channel is moved to its new
position and all other channels are shifted accordingly.
6 Repeat steps 4 to 5 until you have moved all the channels to
the required programme numbers.
7 Press the EXIT button to exit.
TV
Channel
Country
: Belgium
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
LNA
: Off
Move
Enter
TV








Return
Sort
Prog.
0
1
2
3
4
Ch.

C−−
C76
C5
C6
C7

Move
Name

Enter
Return
Assigning Names to Channels
Channel names will be assigned automatically when channel
information is broadcast. These names can be changed,
allowing you to assign new names.
1 Press the MENU button to display the menu.
2 Press the ▲ or ▼ button to select Channel, then press the
ENTER button.
3 Press the ▲ or ▼ button to select Name, then press the
ENTER button.
4 Press the ▲ or ▼ button to select the channel to be assigned to
a new name, then press the ENTER button.
5 Press the ▲ or ▼ button to select a letter, a number, or a
symbol (Results in this sequence: A~Z, 0~9, +, -, *, /, blank).
Move on to the previous or next letter by pressing the ◄ or ►
button, then press the ENTER button.
6 Repeat steps 4 to 5 for each channel to be assigned to a new
name.
7 Press the EXIT button to exit.
TV
Channel
Country
: Belgium
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
LNA
: Off
Move
Enter
TV








Return
Name
Prog.
0
1
2
3
4
Move
Ch.

C−−
C76
C5
C6
C7

Name
−−−−−
−−−−−
−−−−−
−−−−−
−−−−−
Enter
Return
English - 17
BN68-01171P-00Eng_0223.indd
17
2007-02-23
ソタネト 1:43:32
Fine Tuning Channel Reception
If the reception is clear, you do not have to fine tune the
channel, as this is done automatically during the search and
store operation.
If the signal is weak or distorted, you may have to fine tune the
channel manually.
1 Press the MENU button to display the menu.
2 Press the ▲ or ▼ button to select Channel, then press the
ENTER button.
3 Press the ▲ or ▼ button to select Fine Tune, then press the
ENTER button.
4 To obtain a sharp, and clear picture and good sound quality,
press the ◄ or ► button until you reach the optimal setting.
Press the ENTER button.
To reset the fine tuning to 0, select Reset by pressing the
▲ or ▼ button. Press the ENTER button.
5 Press the EXIT button to exit.
Fine Tune Store will change the colour of the Channel OSD
(On Screen Display) from White to Red and add the “*”
mark.
TV
Channel
Country
: Belgium
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
LNA
: Off
Move
Return
Fine Tune
P 1
➢
➢
Enter








+3
Reset
Adjust
Save
Return
P 1*
Mono
Picture
Sound
SRS TS XT
−− : −−
: Dynamic
: Custom
: Off
LNA (Low Noise Amplifier) (PS42Q91H/PS42Q92H/PS50Q91H/PS50Q92H)
This function is very useful in the situation that the TV is used
TV
Channel
in weak signal.
Country
: Belgium
Auto Store
LNA amplifies the TV signal in the weak signal area, a low-noise
Manual Store
preamplifier boosts the incoming signal.
Channel Manager
Sort
1 Press the MENU button to display the menu.
Name
Fine Tune
2 Press the ▲ or ▼ button to select Channel, then press the
LNA
: Off
ENTER button.
3 Press the ▲ or ▼ button to select LNA, then press the ENTER
Move
Enter
button.
4 Select Off or On by pressing the ▲ or ▼ button, then press the
ENTER button.
5 Press the EXIT button to exit.
Depending on areas, factory mode of LNA, will be set up as On or Off.








Return
➢
English - 18
BN68-01171P-00Eng_0223.indd
18
2007-02-23
ソタネト 1:43:32
Changing the Picture Standard
You can select the type of picture which best corresponds to
your viewing requirements.
1 Press the MENU button to display the menu.
2 Press the ENTER button to select Picture.
3 Press the ENTER button again to select Mode.
4 Select the required mode by pressing the ▲ or ▼ button, then
press the ENTER button.
Available modes: Dynamic, Standard, Movie
The settings values may vary depending on the input
source. (ex. RF, Video, Component, PC, or HDMI)
5 Press the EXIT button to exit.
TV
Picture
Mode
: Dynamic
Contrast
Brightness
Sharpness
Colour
Tint
G 50
Colour Tone
: Cool1
Detailed Settings

100
45
75
55
R 50


 More
Move
➢
TV
Enter
Return
Picture
Dynamic
Mode
: Dynamic
Standard
Contrast
Movie
Brightness
Sharpness
Colour
Tint
G 50
R
Colour Tone
: Cool1

Detailed Settings
100
45
75
55
50
 More
Move
Enter
Return
can select these options simply by pressing the P.MODE
➢ You
button on the remote control.
Dynamic for viewing the TV during the day or
➢  Choose
when there is bright light in the room.
 Choose Standard for general TV watching mode.
 Choose Movie when viewing the movie.
Customizing the Picture Settings
Your television has several setting options that allow you to
control the picture quality.
1 Press the MENU button to display the menu.
2 Press the ENTER button to select Picture.
3 Press the ENTER button again to select Mode.
4 Select the required mode by pressing the ▲ or ▼ button, then
press the ENTER button.
Available modes: Dynamic, Standard, Movie
5 Select the required option by pressing the ▲ or ▼ button, then
press the ENTER button.
6 When you are satisfied with your setting, press the ENTER
button.
7 Press the EXIT button to exit.
TV
Picture
Mode
: Dynamic
Contrast
Brightness
Sharpness
Colour
Tint
G 50
Colour Tone
: Cool1
Detailed Settings

100
45
75
55
R 50


 More
Move
TV
Enter
Return
Picture
Mode
: Dynamic
Contrast
Brightness
Sharpness
Colour
Tint
G 50
Cool2 R
Colour Tone
: Cool1
Cool1
Detailed Settings
Normal �
Warm1
 More
Warm2
100
45
75
55
50
 Contrast – Brightness – Sharpness – Colour – Tint (NTSC
only)
 Contrast – Brightness – Colour Tone : PC Mode
Press the ◄ or ► button until you reach the optimal setting.
Move
Enter
Return
 Colour Tone: Cool2/Cool1/Normal/Warm1/Warm2
When the picture mode is set to Dynamic or Standard, Warm1 and Warm2 cannot be selected.
 Reset: Cancel/OK
Select OK. You can return to the factory defaults picture settings.
The reset function is set for each picture mode and colour tone.
➢
➢
English - 19
BN68-01171P-00Eng_0223.indd
19
2007-02-23
ソタネト 1:43:34
Configuring Detailed Settings on the Picture
You can set detailed picture settings.
1 Press the MENU button to display the menu.
2 Press the ENTER button to select Picture.
3 Press the ▲ or ▼ button to select Detailed Settings, then
press the ENTER button.
4 Select the required option by pressing the ▲ or ▼ button, then
press the ENTER button.
Available options: Black Adjust, Dynamic Contrast, Gamma,
White Balance, My Colour Control, Edge Enhancement,
Colour Space
5 When you are satisfied with your setting, press the ENTER
button.
6 Press the EXIT button to exit.
TV
Picture
Mode
: Movie
Contrast
Brightness
Sharpness
Colour
Tint
G 50
Colour Tone
: Warm2
Detailed Settings

80
65
35
35
R 50


 More
Move
TV
Enter
Return
Detailed Settings
Black Adjust
Dynamic Contrast
Gamma
White Balance
My Colour Control
Edge Enhancement
Colour Space
: Off
: Low
: 0
: Off







 Black Adjust: Off/Low/Medium/High
: Wide
You can directly select the black level on the screen to adjust
the screen depth.
 Dynamic Contrast: Off/Low/Medium/High
Move
Enter
Return
You can adjust the screen contrast so that the optimal contrast
is provided.
 Gamma: -3 ~ +3
You can adjust the middle brightness of pictures.
Press the ◄ or ► button until you reach the optimal setting.
 White Balance: R-Offset/G-Offset/B-Offset/R-Gain/G-Gain/B-Gain/Reset
You can adjust the color temperature for more natural picture colors.
R-Offset/G-Offset/B-Offset/R-Gain/G-Gain/B-Gain: Changing the adjustment value will refresh the
adjusted screen.
Select the required option by pressing the ▲ or ▼ button, then press the ENTER button. Press the ◄
or ► button until you reach the optimal setting.
Reset: The previously adjusted white balance will be reset to the factory defaults.
 My Colour Control: Pink/Green/Blue/White/Reset
This setting can be adjusted to suit your personal preferences.
Pink/Green/Blue/White: Changing the adjustment value will refresh the adjusted screen.
Select the required option by pressing the ▲ or ▼ button, then press the ENTER button. Press the ◄
or ► button until you reach the optimal setting.
Reset: The previously adjusted colours will be reset to the factory defaults.
 Edge Enhancement: Off/On
You can emphasize object boundaries.
 Colour Space: Auto/Wide
You can set the colour reproduction space for the input signal to Auto or Wide.
➢ When the picture mode is set to Movie or Standard, Detailed Settings can be selected.
English - 20
BN68-01171P-00Eng_0223.indd
20
2007-02-23
ソタネト 1:43:34
Selecting the Picture Size
You can select the picture size which best corresponds to your
TV
viewing requirements.
1 Press the MENU button to display the menu.
2 Press the ENTER button to select Picture.
3 Press the ▲ or ▼ button to select Size, then press the ENTER
button.
4 Select the required option by pressing the ▲ or ▼ button, then
press the ENTER button.
Available options: Auto Wide, 16:9, Wide Zoom, Zoom, 4:3,
Just Scan
TV
 Auto Wide: Expanding and pulling up the picture from 4:3
to 16:9 ratio.
 16:9: Sets the picture to 16:9 wide mode.
 Wide Zoom: Magnify the size of the picture more than 4:3.
Move the screen up/down using the ▲ or ▼ button after
selecting the by pressing the ► or ENTER button.
 Zoom: Magnify the size of the picture vertically on screen.
 4:3: Sets the picture to 4:3 normal mode.
 Just Scan: Use the function to see the full image without
any truncation when HDMI 1080i/1080p signals are input.
With the HDMI Just Scan picture size, depending on
the AV devices, the screen may be cut off or a specific
colour appears on the screen.
5 Press the EXIT button to exit.
You can change the picture size simply by pressing the
P.SIZE button on the remote control.
Depending on the input source, the picture size options may vary.
The items available may differ depending on the selected mode.
Picture
 More
Size
Screen Mode
Digital NR
Active Colour
DNIe
Movie Plus
Reset
Move
: Auto Wide
: 16 : 9
: Auto
: On
: Off
: On
: OK
Enter







Return
Size
Auto Wide
16:9
Wide Zoom
Zoom
4:3
Just Scan
Move
Enter
Return
➢
➢
➢
➢
Positioning and Sizing the screen using Zoom
 Resizing the screen using the Zoom enables the positioning and sizing of the screen to up/down
direction using the ▲ or ▼ button as well as the screen size.
 Move the screen up/down using the ▲ or ▼ button after selecting the by pressing the ◄ or ►
button.
 Resize the screen vertically using the ▲ or ▼ button after selecting the by pressing the ◄ or ►
button.
Selecting the Screen Mode
When setting the picture size to Auto Wide in a 16:9 wide TV,
you can determine the picture size you want to see the 4:3
WSS (Wide Screen Service) image or nothing. Each individual
European country requires different picture size so this
function is intended for users to select it.
1 Press the MENU button to display the menu.
2 Press the ENTER button to select Picture.
3 Press the ▲ or ▼ button to select Screen Mode, then press
the ENTER button.
4 Select the required option by pressing the ▲ or ▼ button, then
press the ENTER button.
Available options: 16:9, Wide Zoom, Zoom, 4:3
 16:9: Sets the picture to 16:9 wide mode.
 Wide Zoom: Magnify the size of the picture more than 4:3.
 Zoom: Magnify the size of the picture vertically on screen.
 4:3: Sets the picture to 4:3 normal mode.
5 When you are satisfied with your setting, press the ENTER button.
6 Press the EXIT button to exit.
TV
Picture
 More
Size
Screen Mode
Digital NR
Active Colour
DNIe
Movie Plus
Reset
Move
: Auto Wide
: 16 : 9
: Off
: On
: Off
: On
: OK
Enter







Return
English - 21
BN68-01171P-00Eng_0223.indd
21
2007-02-23
ソタネト 1:43:35
Digital NR / Active Colour / DNIe / Movie Plus
1
2
3
4
5


TV
Picture
Press the MENU button to display the menu.
 More
Press the ENTER button to select Picture.
Size
: Auto Wide 
Select the required option by pressing the ▲ or ▼ button, then
Screen Mode
: 16 : 9


Digital NR
: Auto
press the ENTER button.
Active Colour
: On


DNIe
: Off
Available options: Digital NR, Active Colour, DNIe, Movie

Movie Plus
: On
Plus

Reset
: OK
When you are satisfied with your setting, press the ENTER
button.
Move
Enter
Return
Press the EXIT button to exit.
Digital NR: Off/Low/Medium/High/Auto
If the signal received by the television is weak, you can activate this feature to reduce any static and
ghosting that may appear on the screen.
Active Colour: Off/On
If you turn on this option, the colours of the sky and grass will be stronger and clearer for a more vivid
on-screen picture.
This function is not available in PC mode.
When you select Standard (PS42Q91H/PS42Q92H/PS50Q91H/PS50Q92H) or Movie in Picture
Mode, the Active Colour automatically changes to Off and it is deactivated.
When the Picture Mode is set to Dynamic, the Active Colour is activated regardless of the
value of Picture Mode.
DNIe: Off/Demo/On
This TV includes the DNIe function so as to provide a high visual quality. If you set DNIe to on, you
can view the screen with the DNIe feature activated. If you set the DNIe to Demo, you can view the
applied DNIe and normal pictures on the screen, for demonstration purposes. Using this function, you
can view the difference in the visual quality.
DNIeTM (Digital Natural Image engine)
This feature brings you more detailed image with 3D noise reduction, detail enhancement,
contrast enhancement and white enhancement. New image compensation Algorithm gives
brighter, clearer, more detailed image to you. DNIeTM technology will fit every signal into your
eyes.
This function is not available in PC mode.
Movie Plus: Off/On (PS42Q91H/PS42Q92H/PS50Q91H/PS50Q92H)
You can view more natural skin and clear text even in fast moving scenes.
➢
➢

➢

➢
English - 22
BN68-01171P-00Eng_0223.indd
22
2007-02-23
ソタネト 1:43:36
Sound Features
1
2
3
4
5

TV
Sound
Press the MENU button to display the menu.

Mode
: Custom
Press the ▲ or ▼ button to select Sound, then press the
Equalizer

ENTER button.

SRS TS XT
: Off
: Off

Auto Volume
Select the required option by pressing the ▲ or ▼ button, then

Internal Mute
: Off

Sound Select
: Main
press the ENTER button.
Reset
Available options: Mode, Equalizer, SRS TS XT, Auto Volume,
Internal Mute, Reset (If Game Mode is On)
When you are satisfied with your setting, press the ENTER
Move
Enter
Return
button.
Press the EXIT button to exit.
< If Game Mode is On >
Mode: Standard/Music/Movie/Speech/Custom
TV
Sound
You can select the type of special sound effect to be used when

Mode
: Custom
watching a given broadcast.
Equalizer


SRS TS XT
: Off
You can select these options simply by pressing the
: Off

Auto Volume
S.MODE button on the remote control.

Internal Mute
: Off

Sound Select
: Main
Equalizer: Balance/100Hz/300Hz/1kHz/3kHz/10kHz
Reset
The television has several settings which allow you to control
the sound quality.
If you make any changes to these settings, the sound mode
Move
Enter
Return
is automatically switched to Custom.
SRS TS XT: Off/On
TruSurround XT is a patented SRS technology that solves the
problem of playing 5.1 multichannel content over two speakers.
TruSurround delivers a compelling, virtual surround sound
experience through any two-speaker playback system, including
internal television speakers. It is fully compatible with all
TV
Equalizer
multichannel formats.
You can select these options simply by pressing the
R
SRS( ) button on the remote control.
+
+
TruSurround XT, SRS and
0
0
Symbol are trademarks of SRS Labs,
L
Inc. TruSurround XT technology is
Balance 100Hz 300Hz 1kHz 3kHz 10kHz
incorporated under license from SRS
Labs, Inc.
Move
Adjust
Return
Auto Volume: Off/On
Each broadcasting station has its own signal conditions, and
so it is not easy to adjust the volume every time the channel is
changed. This feature lets you automatically adjust the volume
of the desired channel by lowering the sound output when the
modulation signal is high or by raising the sound output when
the modulation signal is low.
Internal Mute: Off/On
If you want to hear the sound through separate speakers, cancel the internal amplifier.
The +, - and MUTE buttons do not operate when the Internal Mute is set to On.
Sound Select: Main/Sub
When the PIP feature is activated, you can listen to the sound of the sub (PIP) picture.
− Main: Used to listen to the sound of the main picture.
− Sub: Used to listen to the sound of the sub picture.
Reset
If Game Mode is On, the Reset Sound function is activated. Selecting the Reset function after setting
the equalizer resets the equalizer setting to the factory defaults.
➢

➢

➢
➢




➢
TRADEMARK & LABEL LICENSE NOTICE
Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
English - 23
BN68-01171P-00Eng_0223.indd
23
2007-02-23
ソタネト 1:43:38
Selecting the Sound Mode (depending on the model)
The DUAL I-II button displays/controls the processing and
output of the audio signal. When power is switched on, the
mode is automatically preset to either “DUAL-I” or “Stereo”,
depending on the current transmission.
Type of broadcast
Regular broadcast
(Standard audio)
Regular + NICAM Mono
NICAM
Mono (Normal)
NICAM Stereo
NICAM stereo
Mono (Normal)
NICAM
Stereo
NICAM DUAL-I/II
A2
Stereo
➢
On-screen indication
Mono (Normal use)
NICAM
dual-1
Regular broadcast
(Standard audio)
Bilingual or DUAL-I/II
Dual I
Stereo
Stereo
Mono
(Normal)
NICAM
dual-2
Mono (Normal use)
Dual II
Mono (Forced
mono)
 If the receiving conditions deteriorate, listening will be easier if the mode is set to Mono.
 If the stereo signal is weak and automatic switching occurs, switch to Mono.
 When receiving a mono sound in the AV mode, connect to the “AUDIO-L” input connector on the
panel (front or side). If the mono sound comes out only from left speaker, press the DUAL I-II
button.
English - 24
BN68-01171P-00Eng_0223.indd
24
2007-02-23
ソタネト 1:43:39
Time Features
1
2
TV
Setup
Press the MENU button to display the menu.

Plug & Play
Press the ▲ or ▼ button to select Setup, then press the

Language
: English
ENTER button.

Time

Game Mode
: Off
3 Press the ▲ or ▼ button to select Time, then press the ENTER

Blue Screen
: Off

Melody
: Off
button.

PC
4 Select the required option by pressing the ▲ or ▼ button, then

Home Theatre PC : Off

Light Effect
: Off
press the ENTER button.
 More
Available options: Clock Set, Sleep Timer, Timer 1, Timer 2,
Move
Enter
Return
Timer 3
TV
Time
5 When you are satisfied with your setting, press the ENTER
button.

Clock Set
: 00 : 00

Sleep Timer
: Off
6 Press the EXIT button to exit.
Timer 1
: Inactivated 
Timer 2
: Inactivated 
 Clock Set
Timer 3
: Inactivated 
You can set the television clock so that the current time is
displayed when pressing the INFO button on the remote control.
You must also set the time if you wish to use the automatic on
or off timers.
Move
Enter
Return
− Press the ◄ or ► button to select Month, Day, Year, Hour,
or Minute. Set these by pressing the ▲ or ▼ button.
TV
Timer 1
You can set the Month, Day, Year, Hour, or Minute
On Time
directly by pressing the numeric buttons on the remote
00 :
00
No
control.
Off Time
00 :
00
No
In the event of a power interruption or the set being turned
Repeat
Volume
off at the supply, the settings for the Clock will be lost.
Once
10
 Sleep Timer
Programme
You can select a time period of between 30 and 180 minutes
01
after which the television automatically switches to standby
Move
Adjust
Return
mode.
− Select the preset time interval (Off, 30, 60, 90, 120, 150, or
180) for staying on by pressing the ▲ or ▼ button.
You can select these options simply by pressing the SLEEP
button on the remote control. If the sleep timer is not yet
set, Off is displayed. If it is already set, the remaining time
before which the television switches to standby mode is
displayed.
 Timer 1 / Timer 2 / Timer 3
You can set the On/Off timers so that the television will switch
on or off automatically at the time you select.
You must set the clock first.
− Press the ◄ or ► button to select the required item below.
Press the ▲ or ▼ button to adjust to the setting satisfied.
On Time : Select hour, minute, and No(Inactivate)/Yes(Activate). (To activate timer with the
setting satisfied, set to Yes.)
Off Time : Select hour, minute, and No(Inactivate)/Yes(Activate). (To activate timer with the
setting satisfied, set to Yes.)
Repeat : Select Once, Everyday, Mon~Fri, Mon~Sat, or Sat~Sun.
Volume : Select the required volume level.
Programme : Select the required channel.
You can set the hour, minute, and channel directly by pressing the number buttons on the
remote control.
➢
➢
➢
☛
➢
Power Off
☛ Auto
When you set the timer “On”, the TV will eventually turn off, if no controls are operated for 3 hours
after the TV was turned on by timer. This function is only available in timer “On” mode and prevents
overheating, which may occur if a TV is on for too long time.
English - 25
BN68-01171P-00Eng_0223.indd
25
2007-02-23
ソタネト 1:43:40
Language / Blue Screen / Melody / Light Effect /
Energy Saving / HDMI Black Level
1
2
3
4
5





TV
Setup
Press the MENU button to display the menu.
Plug & Play

Press the ▲ or ▼ button to select Setup, then press the

Language
: English
ENTER button.

Time

Game Mode
: Off
Select the required option by pressing the ▲ or ▼ button, then

Blue Screen
: Off

Melody
: Off
press the ENTER button.

PC
Available options: Language, Blue Screen, Melody, Light

Home Theatre PC : Off
Off

Light
Effect
:
Effect, Energy Saving, HDMI Black Level
 More
When you are satisfied with your setting, press the ENTER
Move
Enter
Return
button.
TV
Setup
Press the EXIT button to exit.
 More
Language

Wall-Mount Adjustment
It is variable depending on the model. When you start using the
Energy Saving
: Off


HDMI Black Level : Low
television for the first time, you must select the language which

PIP
will be used for displaying menus and indications.
Screen Burn Protection

Blue Screen: On/Off
If no signal is being received or the signal is very weak, a blue
screen automatically replaces the noisy picture background. If
Move
Enter
Return
you wish to continue viewing the poor picture, you must set the
Blue Screen to Off.
Melody: Off/Low/Medium/High
The TV power on/off melody sound can be adjusted.
Light Effect: Off/Standby Mode On/Watching Mode On/On
You can turn on/off the blue LED on the front of TV according to the situation. Use it for saving power
or when the LED dazzles your eyes.
− Off: The blue LED is always off.
− Standby Mode On: The blue LED lights while in Standby mode and it turns off when your TV is
turned on.
− Watching Mode On: The blue LED lights when watching TV and it turns off when your TV is
turned off.
− On: The blue LED always lights.
Set the Light Effect to Off to reduce the power consumption.
Energy Saving: Off/Low/Medium/High
This feature adjusts the screen brightness depending on the surrounding lighting conditions.
− Off: Switches off the Energy Saving mode.
− Low: Operates in standard mode regardless of the surrounding illumination.
− Medium: Enters Medium power saving mode regardless of the surrounding illumination.
− High: Enters maximum power saving mode regardless of the surrounding illumination.
You can select these options simply by pressing the
E.SAVING button on the remote control. (PS42C91H/
PS50C91H)
➢
➢
 HDMI Black Level: Normal/Low
Using this function, you can adjust the image quality when the screen burn (appearance of black
level, low contrast, low color, etc.) is encountered by the HDMI input for RGB limited range (16 to
235).
This function is active only when the external input connects to HDMI and the RGB signals are
input.
➢
English - 26
BN68-01171P-00Eng_0223.indd
26
2007-02-23
ソタネト 1:43:41
Using the Game Mode
When connecting to a game console such as PlayStationTM or
TV
Setup
XboxTM, you can enjoy a more realistic gaming experience by
Plug & Play


Language
: English
selecting game menu.

Time
1 Press the MENU button to display the menu.

Game Mode
: Off
2 Press the ▲ or ▼ button to select Setup, then press the

Blue Screen
: Off

Melody
: Off
ENTER button.

PC
3 Press the ▲ or ▼ button to select Game Mode, then press the

Home Theatre PC : Off

Light Effect
: Off
ENTER button.
 More
4 Select Off or On by pressing the ▲ or ▼ button, then press the
Move
Enter
Return
ENTER button.
5 Press the EXIT button to exit.
Restrictions on Game mode (Caution)
 To disconnect the game console and connect another external device, set Game Mode to Off.
 If you display the TV menu in Game Mode, the screen shakes slightly.
 The mark ( ) appears on the screen which means that Game Mode is On with the
selected source.
If Game Mode is On :
 Picture Mode is automatically changed to Standard and users cannot change the mode.
 Sound Mode in the Sound menu is deactivated. Adjust the sound using the equalizer.
 The Reset Sound function is activated. Selecting the Reset function after setting the
equalizer resets the equalizer setting to the factory defaults.
Game Mode is not available in TV mode.
If the picture is poor when external device is connected to TV, check if Game Mode is On.
Set Game Mode to Off and connect external devices.
➢
➢
➢
➢
English - 27
BN68-01171P-00Eng_0223.indd
27
2007-02-23
ソタネト 1:43:42
Wall- mount adjustment (Sold separately)
Once the wall mount is installed, the position of your TV can be easily adjustable.
Rear Panel
Auto Wall-Mount
SERVICE Cable (Not supplied)
Entering the menu
1
2
3
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Setup, then press the
ENTER button.
Press the ▲ or ▼ button to select Wall-Mount Adjustment,
then press the ENTER button.
Adjust to the desired position using the ▲/▼/◄/► buttons.
Press the EXIT button to exit.
press an arrow button when no OSD is displayed on the
➢ IfTVyouscreen,
the Adjustment screen appears.
you turn the power off, your TV moves to the initial
➢ When
installation position.When you turn the power on, your TV
TV
Setup
 More
Wall-Mount Adjustment
Energy Saving
: Off
HDMI Black Level : Low
PIP
Screen Burn Protection
Move





Enter
Return
Wall-Mount Adjustment
Position1
moves to the last remembered position you adjusted.
Position
Adjust
Using the remote Control Buttons
Button
1
INFO
2
Center
3
Exit
Operations
Wall-mount angle adjustment
Tilt Up, Tilt Down, Move right, Move left
Reset
Moves to the initial installation position
Remembering the position and
moving to the remembered position
Remembers 3 positions with the Red, Green and
Yellow buttons.
Moves to the remembered position using these 3
color buttons.
installation, refer to the Installation Manual provided.
➢ For
product installation and the installation and moving of the wall mount, make sure to consult a
➢ For
specialized installation company.
installation manual is to be used when attaching the wall mount to a wall. When attaching to
➢ This
other building materials, please contact your nearest dealer.
English - 28
BN68-01171P-00Eng_0223.indd
28
2007-02-23
ソタネト 1:43:44
Viewing the Picture in Picture (PIP)
You can display a sub picture within the main picture. In this
TV
Setup
way you can watch TV program or monitor the video input from
 More

Wall-Mount Adjustment
any connected devices.
Energy Saving
: Off


HDMI Black Level : Low
1 Press the MENU button to display the menu.

PIP
2 Press the ▲ or ▼ button to select Setup, then press the
Screen Burn Protection

ENTER button.
3 Press the ▲ or ▼ button to select PIP, then press the ENTER
button.
Move
Enter
Return
4 Select the required option by pressing the ▲ or ▼ button, then
press the ENTER button.
TV
PIP
Available options: PIP(On/Off), Source, Size, Position,
PIP
: On

Source
: TV

Programme
Size
:

Position
:

5 When you are satisfied with your setting, press the ENTER
Programme
:P 1

button.
6 Press the EXIT button to exit.
 PIP: On/Off
You can activate or deactivate the PIP function.
Move
Enter
Return
You can select these options simply by pressing the PIP
button on the remote control.
 Source: TV/Ext.1/Ext.2/AV
You can select a source of the sub-picture.
You can select these options simply by pressing the
SOURCE button on the remote control.
 Size:
/
/
You can select a size of the sub-picture.
You cannot use the Double size ( , ) function for Component or HDMI mode.
 Position:
/
/
/
You can select a position of the sub-picture.
You can select these options simply by pressing the POSITION button on the remote control.
 Programme
You can select a channel of the sub-picture only when the Source is set to TV.
You can select the channel of the sub picture simply by pressing the P
or P
button.
➢
➢
➢
➢
➢
Table of PIP Settings
X - This PIP combination is not available.
O - This PIP combination is available.
Sub
Main
Component
HDMI
PC
TV
O
O
O
Ext.1 Ext.2
O
O
O
O
O
O
AV
O
O
O
S-Video Component HDMI
X
X
X
X
X
X
X
X
X
PC
X
X
X
English - 29
BN68-01171P-00Eng_0223.indd
29
2007-02-23
ソタネト 1:43:46
Screen Burn Protection
To reduce the possibility of screen burn, this unit is equipped
with screen burn prevention technology. This technology
enables you to set picture movement up/down (Vertical Line)
and side to side (Horizontal Dot). The Time setting allows
you to program the time between movement of the picture in
minutes.
1 Press the MENU button to display the menu.
2 Press the ▲ or ▼ button to select Setup, then press the
ENTER button.
3 Press the ▲ or ▼ button to select Screen Burn Protection,
then press the ENTER button.
4 Select the required option by pressing the ▲ or ▼ button, then
press the ENTER button.
Available options: Pixel Shift, All White, Signal Pattern, Side
Gray
5 When you are satisfied with your setting, press the ENTER
button.
6 Press the EXIT button to exit.
 Pixel Shift: Using this function, you can minutely move pixels
on the PDP in horizontal or vertical direction to minimize after
image on the screen.
− Set Pixel Shift to On by pressing the ▲ or ▼ button, then
press the ENTER button.
− Select the required option by pressing the ▲ or ▼ button,
then press the ENTER button.
Available options: Horizontal Dot, Vertical Line, Time
Optimum condition for pixel shift;
➢
PC
Horizontal Dot
Vertical Line
Time (minute)
1
1
2
TV/Ext/AV/S-Video/
Component/HDMI
2
2
2 min
TV
Setup
 More
Wall-Mount Adjustment
Energy Saving
: Off
HDMI Black Level : Low
PIP
Screen Burn Protection
Move
TV
Enter





Return
Screen Burn Protection
Pixel Shift
All White
Signal Pattern
Side Gray
Move
TV
: Off
Enter




Return
Pixel Shift
: On
:2
:2
: 2 min
Pixel Shift
Horizontal Dot
Vertical Line
Time
Move
Enter




Return
➢ The Pixel Shift value may differ depending on the monitor size (inches) and mode.
 All White: This function helps remove after images on the screen by changing the colour of pixels to
white. Use this function when there are remaining after images or symbols on the screen especially
when you displayed a still image on the screen for a long time.
 Signal Pattern: This function helps remove after images on the screen by moving all the pixels on
the PDP according to a pattern. Use this function when there are remaining after images or symbols
on the screen especially when you displayed a still image on the screen for a long time.
 Side Gray: When you watch TV with the screen ratio of 4:3, the screen is prevented from any
damage by adjusting the white balance on both extreme left and right sides.
− Dark: When you set the screen ratio to 4:3, it darkens the left and right sides.
− Light: When you set the screen ratio to 4:3, it brightens the left and right sides.
To remove after images on the screen, use either All White or Signal Pattern function. Although
both of the two functions remove after images on the screen, Signal Pattern is more effective.
The after image removal function has to be executed for a long time (approximately 1 hour) to
effectively remove after images on the screen. If after image is not improved after the execution of the
function, repeat the function again.
Press any button on the remote control to cancel this feature.
➢
➢
➢
English - 30
BN68-01171P-00Eng_0223.indd
30
2007-02-23
ソタネト 1:43:47
Setting up Your PC Software (Based on Windows XP)
The Windows display-settings for a typical computer
are shown below. But the actual screens on your PC will
probably be different, depending upon your particular
version of Windows and your particular video card. But even
if your actual screens look different, the same, basic set-up
information will apply in almost all cases. (If not, contact your
computer manufacturer or Samsung Dealer.)
1 Right click the mouse on the Windows Desktop, then click on
Properties.
The Display Properties will be displayed.
2 Click on Settings tab, then set the Display Mode with
reference to the Display Modes Table. You do not need to
change the Colours settings.
3 Click on Advanced. A new settings dialog box will be
displayed.
4 Click on the Monitor tab, then set the Screen refresh rate with reference to the Display Modes
Table. Set the Vertical Frequency and Horizontal Frequency individually if you can do so instead of
setting the Screen refresh rate.
5 Click on OK to close the window, then Click on OK button to the Display Properties window.
Automatic re-booting may commence at this moment.
English - 31
BN68-01171P-00Eng_0223.indd
31
2007-02-23
ソタネト 1:43:48
Input Mode (PC)
Both screen position and size will vary depending on the type of PC monitor and its resolution.
The table below shows all of the display modes that are supported:
Vertical Horizontal
Resolution
frequency frequency
(Dot X Line)
(Hz)
(kHz)
640 x 350
70.086
31.469
720 x 400
70.087
31.469
59.940
31.469
70.000
35.000
640 x 480
72.809
37.861
75.000
37.500
60.317
37.879
IBM PC / AT
70.000
43.750
Compatible
800 x 600
72.188
48.077
75.000
46.875
60.004
48.363
70.069
56.476
1024 x 768
72.000
57.672
75.029
60.023
1360 x 768
60.015
47.712
Video
Signal
Vertical
polarity
N
P
N
N/P
N
N
P
N/P
P
P
N
N
N/P
P
P
PS42Q91H/ PS50Q91H/
Horizontal
PS42Q92H/ PS50Q92H/
polarity
PS42C91H PS50C91H
P
✔
✔
N
✔
✔
N
✔
✔
N/P
✔
✔
N
✔
✔
N
✔
✔
P
✔
✔
N/P
✔
✔
P
✔
✔
P
✔
✔
N
✔
✔
N
✔
✔
N/P
✔
✔
P
✔
✔
P
✔
(N: Negative / P: Positive)
The interlace mode is not supported.
The television might operate abnormally if a non-standard video format is selected.
480i/p, 576i/p, 720p, or 1080i is not available in PC mode.
For the PS42Q91H/PS42Q92H/PS42C91H, PC text quality is optimum in XGA mode (1024 x
768@60Hz).
 For the PS50Q91H/PS50Q92H/PS50C91H, PC text quality is optimum in WXGA mode (1360 x
768@60Hz). (The three pixels each on the left and right are grayed at the resolution setting of 1360 x
768@60Hz. This is not a mechanical problem but a result caused by the pixel difference between the
standard resolution and the PDP panel.)




English - 32
BN68-01171P-00Eng_0223.indd
32
2007-02-23
ソタネト 1:43:48
Setting the PC
➢ Preset to the PC mode by pressing the SOURCE button.
1
2
3
4
5
6




Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Setup, then press the
ENTER button.
Press the ▲ or ▼ button to select PC, then press the ENTER
button.
Select the required option by pressing the ▲ or ▼ button, then
press the ENTER button.
Available options: Image Lock, Position, Auto Adjustment,
Image Reset
When you are satisfied with your setting, press the ENTER
button.
Press the EXIT button to exit.
Image Lock: Coarse/Fine
The purpose of picture quality adjustment is to remove or
reduce picture noise.
If the noise is not removed by Fine-tuning alone, then adjust the
frequency as best as possible (coarse) and Fine-tune again.
After the noise has been reduced, re-adjust the picture so that it
is aligned on the center of screen.
1 Press the ▲ or ▼ button to select Coarse or Fine, then
press the ENTER button.
2 Press the ◄ or ► button to adjust the screen quality,
vertical stripes may appear or the picture may be blurry.
Press the ENTER button.
Position
Adjust the PC’s screen positioning if it does not fit the TV
screen.
1 Adjust the position by pressing the ▲/▼/◄/► button.
2 Press the ENTER button.
Auto Adjustment
Auto adjustment allows the PC screen of set to self-adjust to the
incoming PC video signal.
The values of fine, coarse and position are adjusted
automatically.
Image Reset
You can replace all image settings with the factory default
values.
TV
Setup
Plug & Play
Language
Time
Game Mode
Blue Screen
Melody
PC
Home Theatre PC
Light Effect
 More
Move
: English
: Off
: Off
: Off
: Off
: Off
Enter
TV









Return
PC
Image Lock
Position
Auto Adjustment
Image Reset
Move
TV




Enter
Return
Image Lock
Coarse
Fine
50
31
Move
TV
Enter
Return
Position
Move
Enter
Return
Auto Adjustment in Progress
Please wait.
Image Reset is completed.
Return
English - 33
BN68-01171P-00Eng_0223.indd
33
2007-02-23
ソタネト 1:43:49
Setting the Home Theatre PC
You can view higher quality pictures by configuring the screen
TV
Setup
settings in PC Mode.
Plug & Play
Language
: English
If you set the Home Theatre PC function to On, you can
Time
configure the DNIe and Detailed Settings (when Picture Mode is
Game Mode
: Off
Blue Screen
: Off
set to Standard or Movie) as in PC Mode.
Melody
: Off
PC
1 Press the MENU button to display the menu.
Home Theatre PC : Off
2 Press the ▲ or ▼ button to select Setup, then press the
Light Effect
: Off
 More
ENTER button.
Move
Enter
3 Press the ▲ or ▼ button to select Home Theatre PC, then
press the ENTER button.
4 Select Off or On by pressing the ▲ or ▼ button, then press the ENTER button.
5 Press the EXIT button to exit.
This function is available only in PC mode.









Return
➢
English - 34
BN68-01171P-00Eng_0223.indd
34
2007-02-23
ソタネト 1:43:49
What is Anynet+? (PS42Q91H/PS42Q92H/PS50Q91H/PS50Q92H)
Anynet+ is an AV network system that enables an easy-to-use AV interface for users by controlling
all connected AV devices through the Anynet+ menu when Samsung Electronics AV devices are
connected.
Connecting Anynet+ Devices
The Anynet+ system supports AV devices supporting Anynet+ only.
Check if there is an Anynet+ mark on the AV device to be connected to the TV.
To directly connect to TV
TV
Anynet+ Device 1 Anynet+ Device 2 Anynet+ Device 3
HDMI 1.3 Cable
HDMI 1.3 Cable
Connect the [HDMI 1], [HDMI
2] or [HDMI 3] jack on the TV
and the HDMI OUT jack of the
corresponding Anynet+ device
using the HDMI cable.
HDMI 1.3 Cable
To connect to Home Theater
1
TV
Anynet+ Device 1
Anynet+ Device 2
2
HDMI 1.3 Cable
Home Theater
HDMI 1.3 Cable
HDMI 1.3 Cable
Anynet+ Device 3
Connect the [HDMI 1],
[HDMI 2] or [HDMI 3]
jack on the TV and the
HDMI OUT jack of the
corresponding Anynet+
device using the HDMI
cable.
Connect the HDMI IN jack
of the home theater and
the HDMI OUT jack of the
corresponding Anynet+
device using the HDMI
cable.
HDMI 1.3 Cable
➢ Connect only one receiver.
can connect an Anynet+ device using the HDMI 1.3 cable. Some HDMI cables may not support
➢ You
Anynet+ functions.
➢ Anynet+ works when the AV device supporting Anynet+ is in the Standby or On status.
➢ Anynet+ supports up to 8 AV devices in total.
English - 35
BN68-01171P-00Eng_0223.indd
35
2007-02-23
ソタネト 1:43:50
Setting Up Anynet+
The following settings are to use Anynet+ functions.
Using the Anynet+ Function
1
2
TV
P1
View TV
Press the Anynet+ button.
Press the ▲ or ▼ button to select Setup, then press the
ENTER button.
Press the ENTER button to select Anynet+ (HDMI-CEC), then
press the ENTER button.
Select Device

Record

Menu on Device

Device Operation

Receiver

Setup
Move
Exit
3
➢
➢
➢
Press the ▲ or ▼ button to select On, then press the ENTER
button.
The Anynet+ (HDMI-CEC) function is enabled.
If you select Off, Anynet+ (HDMI-CEC) is disabled.
When the Anynet+ (HDMI-CEC) function is disabled, all the
Anynet+ related operations are deactivated.
:Off

Enter
Setup
Anynet+ (HDMI-CEC)
: OffOff
Auto Turn Off
: OffOn
Searching Connections
Move
Enter
Return
Turning an Anynet+ Device Off Automatically when the TV is Turned Off
2
3
Setup
Press the ▲ or ▼ button to select Auto Turn Off, then press
the ENTER button.
Anynet+ (HDMI-CEC)
: On
Press the ▲ or ▼ button to select On, then press the ENTER
Auto Turn Off
: Off
Off
button.
The Auto turn off function is enabled.
Searching Connections
On
If you select Off, the Auto turn off function is canceled.
Press the EXIT button to exit.
Move
Enter
Return
The Select Device setting of the TV remote control is to be set
to TV to use the Anynet+ function.
If you set Auto Turn Off to On, connected external devices are also turned off when the TV is turned
off. However, if the device is recording, it may not be turned off.
➢
➢
➢
➢
Scanning and Switching between Anynet+ Devices
1
2
3
4
➢
➢
➢
➢
➢
Press the Anynet+ button.
TV
P1
Press the ▲ or ▼ button to select Select Device, then press
View TV
the ENTER button.
DVDR1

Select Device
Press the ▲ or ▼ button to select to a particular device and
DVDR2
DVD1
Record

press the ENTER button.
DVD2

Menu on Device
It is switched to the selected device.
If you cannot find a device you want, press the ▲ or ▼ button
Device Operation

to select Searching Connections, then press the ENTER
Receiver
:Off

button.

Setup
The meassage Configuring Anynet+ connection... is
Move
Enter
displayed. When searching devices completes, the connected
Return
devices are listed in the Anynet+ menu.
Setup
Switching to the selected devices may take up to 2 minutes.
Anynet+ (HDMI-CEC)
: On

You cannot cancel the operation during the switching
operation.
Auto Turn Off
: On

The time required to scan for devices is determined by the
Searching Connections

number of connected devices.
When the device scan is complete, the number of found
devices is not displayed.
Enter
Return
Move
Although the TV automatically scans devices when it is turned
on using the POWER button, devices connected when the TV is on or under a specific circumstance
are not displayed in the device list. Therefore select Searching Connections menu to search
devices.
If you have selected external input mode by pressing the SOURCE button, you cannot use the
Anynet+ function. Make sure to switch to an Anynet+ device by using the Anynet+ button.
English - 36
BN68-01171P-00Eng_0223.indd
36
Continued...
2007-02-23
ソタネト 1:43:52
Anynet+ Menu
The Anynet+ menu changes depending on the type and status of the Anynet+ devices connected
to the TV.
Anynet+ Menu
Description
View TV
Switches from Anynet+ to TV broadcast mode.
Select Device
Your TV connects to the corresponding device.
Record
Starts a recording. (This menu works only for a device supporting
recording.)
Menu on Device
Shows the menu of the connected device.
Example. When a DVD Recorder is connected, the DVD Recorder’s
title menu appears.
Device Operation
Shows the play control menu of the connected device.
Example. When a DVD Recorder is connected, the play control
menu of the DVD Recorder appears.
Receiver
Sound is output through the receiver.
Setup
You can set the environment for using Anynet+.
TV Remote Control Buttons Available in Anynet+ Mode
Device Type
Operating Status
Available Buttons
After switching to the
device, when the menu of
the corresponding device is
displayed on the screen.
Numeric buttons
▲/▼/◄/►/ENTER buttons
Color buttons
EXIT button
After switching to the device,
while playing a file
◄◄ (Backward search)
►►(Forward search)
(Stop)
► (Play/Pause)
Device with built-in Tuner
After switching to the device,
when you are watching a TV
program
CH ▲/▼ button
Audio Device
When Receiver is activated
VOL +/- button
MUTE button
Anyview2
When watching TV
► (Play/Pause)
Anynet+ Device
Anynet+ function only works when the remote control is set to TV.
➢ The
REC button works only while in the recordable state.
➢ The
cannot control Anynet+ devices using the buttons on the side of the TV. You can control Anynet+
➢ You
devices only using the TV remote control.
TV remote control may not work under certain conditions. In this case, re-select the Anynet+
➢ The
device.
Anynet+ functions don’t operate for the products from other manufacturers.
➢ The
mode, the color buttons may not work properly.
➢ InTheAnynet+
➢ ◄◄, ►► operations may differ depending on the device.
Recording
You can make a recording of a TV program using a recorder.
Press the REC button.
Recording begins. (Only when the Anynet+ enabled recording device is connected.)
The current TV program is recorded in the Watching TV status. If you are watching video from
another device, the video from the device is recorded.
You can also record the source streams by selecting Record after pressing the Anynet+ button.
Before recording, check whether the antenna jack is properly connected to the recording device.
For the antenna connection to the recording device, refer to its user manual.
➢
➢
➢
English - 37
BN68-01171P-00Eng_0223.indd
37
2007-02-23
ソタネト 1:43:52
Listening through a Receiver
You can listen to sound through a receiver instead of the TV speaker.
1 Press the Anynet+ button.
TV
P1
Press the ▲ or ▼ button to select Receiver, then press the
View TV
ENTER button.
Select Device

2 Press the ◄ or ► button to select to On, then press the
Record

ENTER button.

Menu on Device
Now you can listen to sound through the receiver.
Device Operation

3 Press the EXIT button to exit.

Receiver
:On
When the receiver is set to On, you can listen to the TV sound
Setup

through the 2-channel receiver.
Move
Enter
Exit
If the receiver is exclusively for a home theater only (supporting
audio only), it may not appear in the device list.
In case of a content with copyright problem, listening through the receiver may not properly operate.
When listening through the receiver, there are restrictions for using the PIP and audio-related menu.
➢
➢
➢
➢
Check Points before Requesting Service
Symptom
Anynet+ does not work.
I want to start Anynet+.
I want to exit Anynet+.
The Connecting to Anynet+
device… message appears
on the screen.
The Anynet+ device does
not play.
The connected device is not
displayed.
The TV program cannot be
recorded.
Solution
■ Check if the device is an Anynet+ device. The Anynet+ system
supports Anynet+ devices only.
■ Connect only one receiver.
■ Check if the Anynet+ device power cord is properly connected.
■ Check the Anynet+ device’s Video/Audio/HDMI 1.3 cable
connections.
■ Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+
setup menu.
■ Check whether the TV remote control is in TV mode.
■ Check whether it is Anynet+ exclusive remote control.
■ Anynet+ doesn’t work at a certain condition. (Searching channels)
■ When connecting or removing the HDMI 1.3 cable, please make
sure to search devices again or restart your TV.
■ Check if the Anynet+ Function of Anynet+ device is set on.
■ Check if the Anynet+ device is properly connected to the TV and
check if the Anynet+ (HDMI-CEC) is set to On in the Anynet+ Setup
menu.
■ Press the TV button on the TV remote control to switch to TV. Then
press the Anynet+ button to show the Anynet+ menu and select a
menu you want.
■ Select View TV in Anynet+ menu.
■ Press the SOURCE button on the TV remote control and select a
device other than Anynet+ devices.
■ Press any of CH, CH LIST, and PRE-CH to change to the
TV mode. (Note that the channel button operates only when a
tuner-embedded Anynet+ device is not connected.)
■ You cannot use the remote control when you are configuring
Anynet+ or switching to a view mode.
■ Use the remote control when the Anynet+ setting or switching to
view mode is complete.
You cannot use the play function when Plug & Play is in progress.
■
■
■
Check whether or not the device supports Anynet+ functions.
Check whether or not the HDMI 1.3 cable is properly connected.
Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+
setup menu.
■ Search Anynet+ devices again.
■ You can connect an Anynet+ device using the HDMI 1.3 cable only.
Some HDMI cables may not support Anynet+ functions.
Check whether the antenna jack on the recording device is properly
connected.
English - 38
BN68-01171P-00Eng_0223.indd
38
2007-02-23
ソタネト 1:43:52
Teletext Feature (depending on the model)
Most television stations provide written information services
via teletext. The index page of the teletext service gives you
information on how to use the service. In addition, you can select
various options to suit your requirements by using the remote
control buttons.
For teletext information to be displayed correctly, channel reception
must be stable. Otherwise, information may be missing or some
pages may not be displayed.
☛
1 TV
Exit from the teletext display (depending on the model)
2
(index)
Used to display the index (contents) page at any time while you
are viewing teletext.
3
4
5
6
7
8
9
0
!
@
#
(teletext on/mix)
Press to activate teletext mode after selecting the channel
providing the teletext service. Press it twice to overlap the teletext
with the current broadcasting screen.
(hold)
Used to hold the display on a given page if the selected page is
linked with several secondary pages which follow on automatically.
To resume, press it again.
(mode)
Press to select the teletext mode (LIST/FLOF).
If you press it in the LIST mode, it switches into the List save
mode.
In the List save mode, you can save teletext page into list using the
(store) button.
(sub-page)
Used to display the available sub-page.
(page up)
Used to display the next teletext page.
(page down)
Used to display the previous teletext page.
(cancel)
Used to display the broadcast when searching for a page.
(reveal)
Used to display the hidden text (answers to quiz games, for example). To display normal screen,
press it again.
Coloured buttons (red/green/yellow/blue)
If the FASTEXT system is used by a broadcasting company, the different topics covered on a teletext
page are colour-coded and can be selected by pressing the coloured buttons. Press one of them
corresponding to the required. The page is displayed with other coloured information that can be
selected in the same way.
To display the previous or next page, press the corresponding coloured button.
(size)
Press to display the double-size letters in the upper half of the screen. For lower half of the screen,
press it again.
To display normal screen, press it once again.
(store)
Used to store the teletext pages.
can change teletext pages by pressing the numeric buttons on
➢ You
the remote control.
Continued...
English - 39
BN68-01171P-00Eng_0223.indd
39
2007-02-23
ソタネト 1:43:55
The teletext pages are organized according to six categories:
Part
Contents
A
B
C
D
E
F
Selected page number.
Broadcasting channel identity.
Current page number or search indications.
Date and time.
Text.
Status information.
FASTEXT information.
information is often divided between several pages
➢ Teletext
displayed in sequence, which can be accessed by:
 Entering the page number
 Selecting a title in a list
 Selecting a coloured heading (FASTEXT system)
➢ Press the TV button to exit from the teletext display.
English - 40
BN68-01171P-00Eng_0223.indd
40
2007-02-23
ソタネト 1:43:58
Installing the Wall Mount Kit
This installation is to be used when attaching the wall mount to a wall.
When attaching to other building materials, please contact your nearest dealer.
Wall Mount Kit Specifications (VESA)
Product Family
LCD-TV
PDP-TV
1
2
3
4
inch
VESA Spec. (A * B)
Standard Screw (C * D)
Quantity
23 ~ 26
200 * 100
M4 * L10
4
32 ~ 40
200 * 200
M6 * L10
4
46 ~ 52
600 * 400
57
700 * 400
M8 * L15
4
42 ~ 50
600 * 400
63
No VESA
M8
6
We provide the standard dimensions for wall mount kits as shown in the table above.
When purchasing our wall mount kit, a detailed installation manual and all parts necessary for
assembly are provided.
Do not use screws longer than the standard dimension, as they may cause damage to the inside of
the TV set.
Our 63” model does not comply with VESA Specifications. Therefore, you should use our dedicated
wall mount kit for this model.
English - 41
BN68-01171P-00Eng_0223.indd
41
2007-02-23
ソタネト 1:43:59
Setting Up Your Remote Control (PS42Q91H/PS42Q92H/PS50Q91H/PS50Q92H)
After it has been set up properly, your remote control can operate in five different modes: TV, VCR,
Cable, DVD, or Set-Top Box. Pressing the corresponding button on the remote control allows you
to switch between these modes, and control whichever piece of equipment you choose.
The remote control might not be compatible with all DVD Players, VCRs, Cable boxes, and Set-Top
Boxes.
Setting Up the Remote to Operate Your VCR
1 Turn off your VCR.
2 Press the VCR button on your TV’s remote control.
3 Press the SET button on your TV’s remote control.
4 Using the number buttons on your remote control, enter three digits
of the VCR code listed on page 44 of this manual for your brand of
VCR. Make sure you enter three digits of the code, even if the first
digit is a “0”. (If more than one code is listed, try the first one.)
5 Press the POWER button on the remote control. Your VCR should
turn on if your remote is set up correctly.
➢
If your VCR does not turn on after set-up, repeat steps 2, 3 and 4,
but try one of the other codes listed for your brand of VCR. If no
other codes are listed, try each VCR code, 000 through 080.
Note on Using Remote Control Modes: VCR
When your remote control is in VCR mode, the volume buttons still
control your TV’s volume.
Setting Up the Remote to Operate Your Cable Box
1 Turn off your cable box.
2 Press the CABLE button on your TV’s remote control.
3 Press the SET button on your TV’s remote control.
4 Using the number buttons on your remote control, enter three digits
of the cable box code listed on page 45 of this manual for your
brand of cable box.
Make sure you enter three digits of the code, even if the first digit is
a “0”. (If more than one code is listed, try the first one.)
5 Press the POWER button on the remote control.
Your cable box should turn on if your remote is set up correctly.
If your cable box does not turn on after set-up, repeat steps 2, 3
and 4, but try one of the other codes listed for your brand of cable
box. If no other codes are listed, try each code, 000 through 046.
Note on Using Remote Control Modes: Cable Box
When your remote control is in CABLE mode, the volume buttons still
control your TV’s volume.
Continued...
English - 42
BN68-01171P-00Eng_0223.indd
42
2007-02-23
ソタネト 1:44:00
Setting Up the Remote to Operate Your DVD
1 Turn off your DVD.
2 Press the DVD button on your TV’s remote control.
3 Press the SET button on your TV’s remote control.
4 Using the number buttons on your remote control, enter three digits
of the DVD code listed on page 46 of this manual for your brand of
DVD. Make sure you enter three digits of the code, even if the first
digit is a “0”. (If more than one code is listed, try the first one.)
5 Press the POWER button on the remote control.
Your DVD should turn on if your remote is set up correctly.
If your DVD does not turn on after set-up, repeat steps 2, 3 and 4,
but try one of the other codes listed for your brand of DVD. If no
other codes are listed, try each code, 000 through 141.
Note on Using Remote Control Modes: DVD
When your remote control is in DVD mode, the volume buttons still
control your TV’s volume.
Setting Up the Remote to Operate Your Set Top Box
1 Turn off your STB.
2 Press the STB button on your TV’s remote control.
3 Press the SET button on your TV’s remote control.
4 Using the number buttons on your remote control, enter three digits
of the STB code listed on page 45 of this manual for your brand of
STB. Make sure you enter three digits of the code, even if the first
digit is a “0”. (If more than one code is listed, try the first one.)
5 Press the POWER button on the remote control.
Your STB should turn on if your remote is set up correctly.
If your STB does not turn on after set-up, repeat steps 2, 3 and 4,
but try one of the other codes listed for your brand of STB. If no
other codes are listed, try each code, 000 through 074.
Note on Using Remote Control Modes: STB
When your remote control is in STB mode, the volume buttons still
control your TV’s volume.
Continued...
English - 43
BN68-01171P-00Eng_0223.indd
43
2007-02-23
ソタネト 1:44:02
Remote Control Codes
VCR
Brand
SAMSUNG
ADMIRAL
AIWA
AKAI
AUDIO DYNAMICS
BELL&HOWELL
BROKSONIC
CANDLE
CANON
CITIZEN
COLORTYME
CRAIG
CURTIS MATHES
DAEWOO
DB
DIMENSIA
DYNATECH
ELECTROHOME
EMERSON
FISHER
FUNAI
GENERAL ELECTRIC
GO VIDEO
LG(Goldstar)
HARMAN KARDON
HITACHI
INSTANT REPLAY
JC PENNEY
JCL
KENWOOD
KLH
LIOYD
LOGIK
LXI
JVC
MAGNAVOX
MARANTZ
MARTA
KONIA
ORION
MEI
MEMOREX
MGA
MIDLAND
MINOLTA
Code
000 001 002 003 004 005 077 078 079
020
025
004 027 032
007 026
018
022
002 003 006 008 015 055
021 056
002 003 006 008 015 055
007
002 024
002 007 008 017 021 025 056 064 066
003 010 011 012 013 014 015 016
007 026
017
025
034
001 003 006 021 022 025 030 032 034
040 047 050 052 060 063 065 066 067
069 073
018 024 028 029 048 051 061
025
002 005 017 021 056
002
006 007 008 009 010
007
019 025 041 042 074
021
002 007 018 019 021 026 037 041
054 056
007 008 018 021 026 037
007 008 018 026 037
070
025
038
025
081 082 083
021 056 059
007 008 018 021 026 037 062
006
036
073 074 075 076
021
006 021 024 025
034
005
019 041 075
Brand
MITSUBISHI
MONTGOMERY WARD
MTC
MULTITECH
NEC
OPTIMUS
PANASONIC
PENTAX
PENTEX RESEARCH+
PHILCO
PHILIPS
PIONEER
PORTLAND
PROSCAN
QUARTZ
QUASAR
RADIO SHACK/
REALISTIC
RCA
SANSUI
SANYO
SCOTT
SEARS
SHARP
SHIMTOM
SIGNATURE
SONY
SYLVANIA
SYMPHONIC
TANDY
TASHIKA
TATUNG
TEAC
TECHNICS
TEKNIKA
TMK
TOSHIBA
TOTEVISION
UNITECH
VECTOR RESEARCH
VICTOR
VIDEO CONCEPTS
VIDEOSONIC
WARDS
YAMAHA
ZENITH
Code
019 034 041 046
020
002 025
002 005 025 038
007 008 018 026 037 062 064
020
021 056 071 072
019 041 075
008
021 056 059
021 080
019 026 039 053
015 049 055
017
018
021 056
006 018 020 021 024 025 029 034
048 056
002 017 019 021 035 041 043 057
068 076
026
018 024
003 047 052 067
006 018 019 024 028 029 041 048 051
020 034 045 015
027 033 038 058
025
027 033 044
021 025 056 059
025
018 025
006
037
025 037 068
021
006 021 025 031
066
003 019 029 051 052
002 006
002
007 026
026
007 026
002
002 003 006 019 020 021 024 025 034
038 041
007 008 018 026 037
023 027 033
Continued...
English - 44
BN68-01171P-00Eng_0223.indd
44
2007-02-23
ソタネト 1:44:04
CABLE BOX
Brand
SAMSUNG
GI
HAMLIN
HITACHI
JERROLD
MACOM
MAGNAVOX
OAK
PANASONIC
PHILIPS
PIONEER
RCA
REGAL
Code
000 001 002 003 004 005 006 007
041
003 024 031
025 030
038 039
025 030
019 023 028
026
003 022 027 037 044
019 021 023 028
004 018 020 044
014 022 040
003
Brand
REGENCY
SA
SCIENTIFIC ATLAN
SPRUCER
STARGATE 2000
SYLVANIA
TEXSCAN
TOCOM
UNIVERSAL
VIEWSTAR
WARNER AMEX
ZENITH
Code
015 023
042 043
042 043
022
036
016
016
032
033 034
019 021 023 028
046
017 029 035 037 045
SAMSUNG SET-TOP BOX
Product
Ground wave STB
Satellite STB
CABLE STB
STB DVD COMBO
Satellite STB HDD COMBO Standard
Code
001 002
003
004
008
009
Product
Satellite STB HDD COMBO Premium
CABLE STB HDD COMBO Standard
CABLE STB HDD COMBO Premium
Ground wave STB HDD COMBO Standard
Ground wave STB HDD COMBO Premium
Code
010
011
012
013
014
SET-TOP BOX
Brand
ALPHASTAR
ANAM
CHANNEL MASTER
CROSSDIGITAL
CHAPARRAL
DIRECT TV
DAEWOO
DISH NETWORK SYSTEM
DISHPRO
DRAKE
DX ANTENNA
ECHOSTAR
EXPRESSVU
GOI
GE
GENERAL INSTRUMENT
HTS
HOME CABLE
HITACHI
HUGHES NETWORK
IQ
IQ PRISM
JANEIL
JERROID
JVC
Code
023
043
018 034
019
035
015 016 017 019 022 045 060
061 062 065 066 067 068
074
069 070
069
018 024 032
027
025 069 070 071
069
069
065
046 047 048 063 064
069
056
022
015 017
020
020
059
063
069 070
Brand
LG(Goldstar)
MAGNAVOX
MEMOREX
MOTOROLA
MACOM
MITSUBISHI
NEXT LEVEL
PHILIPS
PRIMESTAR
PANASONIC
PAYSAT
PROSCAN
RCA
RADIOSHACK
REALISTIC
STS
STAR TRAK
SKY
SKY LIFE
SHACK
STAR CHOICE
SONY
TOSHIBA
ULTIMATE TV
UNIDEN
ZENITH
Code
044 073
016 021 036 038 039 040 041 042
016
064
018
015
047 048 064
015 016 017 021 033 036 038 039
040 041 042 067
046 049 050 063
058 059 061 062
016
065 066
051 052 053 065 066
064
057
020 027
026
031
005 006 007
064
064
054 060
015 017 028 029 030 072
060 066
016 021 037 055 056 057
024 031 068
Continued...
English - 45
BN68-01171P-00Eng_0223.indd
45
2007-02-23
ソタネト 1:44:04
SAMSUNG DVD
Product
DVD
DVDR
BD Record
VCR COMBO
VCR Record
DHR COMBO
Code
000 001 002
003 004
005 006
007 008 009 010 011
012
013
Product
Home Theater VCR COMBO
HDD Record COMBO
TWIN TRAY COMBO
STB DVD COMBO
DVD Receiver
AV Receiver
Code
014 015 016
017
018
019
020
021
DVD
Brand
ANAM
AUDIOVOX
AUDIOLOGIC
ANABA
APEX DIGITAL
AIWA
BROKSONIC
BLAUPUNKT
B&K
CURTIS MATHES
CYBER HOME
CLARION
CIRRUS
CINEVISION
DAEWOO
DENON
FARENHEIT
FISHER
GPX
GO VIDEO
GE
GREENHILL
HITACHI
HITEKER
HOYO
HARMAN / KARDON
IRT
INTEGRA
JBL
JVC
JATON
KENWOOD
KISS
KONKA
KLH
LG(Goldstar)
LOEWE
LASONIC
MOBILE AUTHORITY
MEMOREX
MALATA
MAGNAVOX
MINTEK
MONYKA
Code
030
075
085
072
070 071 074 086 083 084 088
111 112
114
062
074
122 123
027
065 077 078 079 082
080 125
081
095
066
146
067 068
090
060
061 089 133 135
069 074
074
064 113
071
073
091 110
089
092
091
022 033 115 116
073
051 108 109
073
059 100 106 107
074 075
025 031
057
058
054
055
056
076 093
074 094
073
Brand
NORCENT
NEXT BASE
NEC
NANTAUS
NESA
OPTOMEDIA ELECTRONICS
OPTIVIEW
ONKYO
PHILCO
PRINCETON
PROSCAN
PANASONIC
PHILIPS
ROTEL
RIO
RCA
RAITE
ROWA
SAMPO
SONY
SHERWOOD
SVA
SYLVANIA
SHARP
SANSUI
SANYO
SHINSONIC
SANYO
THOMSON
TOSHIBA
TECHNICS
TVIEW
TOKAI
TEAC
TECHWOOD
TREDEX
URBAN CONCEPTS
VENTURER
VOCOPRO
YAMAHA
YAMAKAWA
XWAVE
ZENITH
Code
048 049 050
052
053
144
074
105
072
076 092 119
044 045
046 047
023
024 034 124 134 136 137 138
036 076
117 118
120
023 035 074 075 131 132
073
038
104
026 029 126 127 128 129
130 141
039 041
042
043 093
140
062
062
094
090
145
028 062 076
139
072
073
096
097
098 099 101
076
075
102
032 063
040 073
103
076 121
English - 46
BN68-01171P-00Eng_0223.indd
46
2007-02-23
ソタネト 1:44:04
How to assemble the Stand-Base (depending on the model)
Using the 6 screws for securing the stand base and the
monitor, firmly attach the monitor to the stand base.
(The exterior of the set may be different than the picture.)
In case of installing your TV on the wall,
close the cover (1) on the stand-base
connection part using two screws for
hiding.
Warning
Firmly secure the stand to the TV
before moving it, as the stand may
fall and could cause serious injury.
or more people should carry
➢ Two
the TV. Never lay the TV on the
floor because of possible damage
to the screen.
Always store the TV upright.
Troubleshooting
Before contacting the Samsung after-sales service, perform the following simple checks.
If you cannot solve the problem using the instructions below, note the model and serial number of
the television and contact your local dealer.
No sound or picture
 Check that the mains lead has been connected to a wall socket.
 Check that you have pressed the (Power) button (On/Off) on the front panel or press the POWER
button on the remote control.
 Check the picture contrast and brightness settings.
 Check the volume.
 Check if Internal Mute is set to ON.
Normal picture but no sound
 Check the volume.
 Check whether the volume MUTE button on the remote control has been pressed.
No picture or black and white picture
 Adjust the colour settings.
 Check that the broadcast system selected is correct.
Sound and picture interference
 Try to identify the electrical appliance that is affecting the television, then move it further away.
 Plug the television into a different main socket.
Blurred or snowy picture, distorted sound
 Check the direction, location and connections of your aerial.
This interference often occurs due to the use of an indoor aerial.
Remote control malfunctions
 Replace the remote control batteries.
 Clean the upper edge of the remote control (transmission window).
 Check that the “+” and “–” ends of the batteries are inserted correctly.
 Check that the batteries are drained.
Screen is black and power indicator light blinks steadily
 On your computer check; Power, Signal Cable.
 The TV is using its power management system.
 Move the computer’s mouse or press any key on the keyboard.




On your equipment check (STB, DVD, etc) ; Power, Signal Cable.
The TV is using its power management system.
Press the Source button on the panel or remote control.
Turn the TV off and on.
English - 47
BN68-01171P-00Eng_0223.indd
47
2007-02-23
ソタネト 1:44:08
Specifications
The descriptions and characteristics in this booklet are given for information purposes only and
are subject to modification without notice.
PS42Q91H/PS42Q92H
PS42C91H
PS50Q91H/PS50Q92H
PS50C91H
42 inch
50 inch
PC Resolution
1024 x 768 @ 60 Hz
1360 x 768 @ 60 Hz
Sound (Output)
10 W + 10 W
10 W + 10 W
15 W + 15 W
10 W + 10 W
1055 x 700 x 104 mm
1055 x 700 x 95 mm
1055 x 757 x 316 mm
1055 x 759 x 316 mm
1231 x 789 x 104 mm
1231 x 789 x 95 mm
1231 x 849 x 316 mm
1231 x 849 x 316 mm
31 kg
31 kg
34 kg
34 kg
42 kg
41 kg
44 kg
44 kg
Model Name
Screen Size (Diagonal)
Dimension (WxHxD)
Body
With stand
Weight
Body
With stand
Environmental Considerations
Operating Temperature
Operating Humidity
Storage Temperature
Storage Humidity
10 °C to 40 °C (50 °F to 104 °F)
10% to 80%, non-condensing
-20 °C to 45 °C (-4 °F to 113 °F)
5% to 95%, non-condensing
This device is a Class B digital apparatus.
➢
 Design and specifications are subject to change without prior notice.
 For the power supply, refer to the label attached to the product.
English - 48
BN68-01171P-00Eng_0223.indd
48
2007-02-23
ソタネト 1:44:15
This page is intentionally
left blank.
BN68-01171P-00Eng_0223.indd
49
2007-02-23
ソタネト 1:44:16
This page is intentionally
left blank.
BN68-01171P-00Eng_0223.indd
50
2007-02-23
ソタネト 1:44:16
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with
separate collection systems)
This marking shown on the product or its literature, indicates that it
should not be disposed with other household wastes at the end of its
working life.
To prevent possible harm to the environment or human health from
uncontrolled waste disposal, please separate this from other types of
wastes and recycle it responsibly to promote the sustainable reuse of
material resources.
Household users should contact either the retailer where they
purchased this product, or their local government office, for details
of where and how they can take this item for environmentally safe
recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract. This product should not be mixed
with other commercial wastes for disposal.
BN68-01171P-00Eng_0223.indd
51
2007-02-23
ソタネト 1:44:16
Contact SAMSUNG WORLD-WIDE
If you have any questions or comments relating to Samsung products, please contact the
SAMSUNG customer care centre.
Kontaktujte SAMSUNG WORLD WIDE (Samsung po celém světě)
Pokud máte dotazy nebo připomínky týkající se výrobků Samsung, kontaktujte středisko péče o
zákazníky společnosti SAMSUNG.
Comment contacter Samsung dans le monde
Si vous avez des suggestions ou des questions concernant les produits Samsung, veuillez
contacter le Service Consommateurs Samsung.
Kontakt zu Samsung
Falls Sie Fragen oder Anregungen zu Samsung-Produkten haben, wenden Sie sich bitte an den
Samsung-Kundendienst.
Kapcsolatfelvétel: SAMSUNG WORLD-WIDE
Bármilyen észrevétele, vagy kérdése van Samsung termékekkel kapcsolatban, forduljon a
SAMSUNG ügyfélszolgálathoz.
Contatta SAMSUNG WORLD-WIDE
Se avete commenti o domande sui prodotti Samsung, contattate il Servizio Clienti Samsung.
Contact Samsung wereldwijd
Wanneer u suggesties of vragen heeft met betrekking tot Samsung producten, gelieve contact op te
nemen met de consumenten dienst van Samsung.
Kontakt do SAMSUNG WORLD-WIDE
Jeżeli masz jakieś uwagi lub pytania w sprawie produktów marki Samsung, skontaktuj się z naszą
infolinią.
Contacte SAMSUNG GLOBAL
Se tem algumas dúvidas ou comentários sobre os produtos Samsung, contacte por favor a nossa
linha de apoio a clientes Samsung.
Skontaktujte SAMSUNG WORLD WIDE (Celosvetový Samsung)
Ak máte nejaké otázky alebo komentáre ohľadom produktov spoločnosti Samsung, prosím,
skontaktujte centrum starostlivosti o zákazníkov spoločnosti SAMSUNG.
Obrnite se na SAMSUNG WORLD WIDE (GLOBALNI SAMSUNG)
V primeru vprašanj ali pripomb v zvezi z izdelki Samsung se obrnite na center za pomoč strankam
SAMSUNG.
Contacte con SAMSUNG WORLD-WIDE
Si tiene alguna pregunta o comentario referente a nuestros productos, por favor contacte con
nuestro Servicio de Atención al Cliente.
01171Q-00Eng_Cover-1.indd
2
2007-02-12
ソタネト 5:22:42
Country
BELGIUM
CZECH REPUBLIC
DENMARK
ESTONIA
FINLAND
FRANCE
GERMANY
HUNGARY
ITALIA
KAZAKHSTAN
LATVIA
LITHUANIA
LUXEMBURG
NETHERLANDS
NORWAY
POLAND
PORTUGAL
REPUBLIC OF IRELAND
RUSSIA
SLOVAKIA
SPAIN
SWEDEN
SWITZERLAND
U.K
UKRAINE
UZBEKISTAN
01171Q-00Eng_Cover-1.indd
3
Customer Care Centre 
02 201 2418
844 000 844
70 70 19 70
800-7267
030-6227 515
08 25 3260 (€ 0,15/Min)
01805 - 121213 (€ 0,14/Min)
06-80-SAMSUNG (7267864)
800 SAMSUNG (7267864)
8 800 080 11 88
800-7267
800-77777
02 261 03 710
0900 20 200 88 (€ 0,10/Min)
815-56 480
0 801 801 881
80 8 200 128
0818 717 100
8-800-200-0400
0800-SAMSUNG (7267864)
902 10 11 30
0771-400 200
1-800-SAMSUNG(7267864)
0870 SAMSUNG (7267864)
8-800-502-0000
140-1234
Web Site
www.samsung.com/be
www.samsung.com/cz
www.samsung.com/dk
www.samsung.ee
www.samsung.com/fi
www.samsung.com/fr
www.samsung.de
www.samsung.com/hu
www.samsung.com/it
www.samsung.kz
www.samsung.com/lv
www.samsung.lt
www.samsung.lu
www.samsung.com/nl
www.samsung.com/no
www.samsung.com/pl
www.samsung.com/pt
www.samsung.com/uk
www.samsung.ru
www.samsung.com/sk
www.samsung.com/es
www.samsung.com/se
www.samsung.com/ch
www.samsung.com/uk
www.samsung.com/ur
www.samsung.uz
2007-02-12
ソタネト 5:22:42