Miele T 224 Operating instructions

Operating instructions
for Washing machine
W 5741
To avoid the risk of accidents
or damage to the machine,
it is essential to read these
instructions before it is installed
and used for the first time.
en - AU, NZ
M.-Nr. 09 493 620
Caring for the environment
Disposal of the packing
material
Disposal of your old appliance
or machine
The transport and protective packing
has been selected from materials which
are environmentally friendly for disposal
and can normally be recycled.
Electrical and electronic appliances /
machines often contain materials
which, if handled or disposed of
incorrectly, could be potentially
hazardous to human health and to the
environment. They are, however,
essential for the correct functioning of
your appliance or machine. Therefore,
please do not dispose of your old
machine or appliance with your
household waste.
Ensure that any plastic wrappings,
bags, etc. are disposed of safely and
kept out of the reach of babies and
young children. Danger of suffocation.
Rather than just throwing these
materials away, please ensure they are
offered for recycling.
Please dispose of it at your local
community waste collection / recycling
centre and ensure that it presents no
danger to children while being stored
for disposal.
It should be unplugged or disconnected
from the mains electricity supply by a
competent person.
The plug must be rendered useless
and the cable cut off directly behind the
appliance to prevent misuse.
2
Contents
Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Operating the machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Before using for the first time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Washing environmentally and economically . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Energy and water consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Detergent consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
How to wash correctly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Brief instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Extra quiet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Spinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Final spin speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Programme chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Extra options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Garment care label symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Programme sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Changing the programme sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Cancelling a programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Interrupting a programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Changing a programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Adding or removing laundry after a programme has started . . . . . . . . . . . . . . . . 31
Safety lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
3
Contents
Detergent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
The correct detergent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Water softeners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Washing with several components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Fabric conditioners and liquid starch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Colour run and dye removers/dyes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Cleaning the drum (Hygiene Info) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Cleaning the external casing and fascia panel . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Cleaning the detergent dispenser drawer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Cleaning the water inlet filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Problem solving guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
What to do if . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
The programme does not start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
The following fault message appears in the display and the programme
has been cancelled. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
The following message appears in the display . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
General problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
An unsatisfactory wash result . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
The drum door does not open when you press the Door button. . . . . . . . . . . . . . 44
Opening the drum door in the event of a blocked drain outlet
and/or power failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
After sales service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Future updates (PC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Appliance warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Optional accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Installation and connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Front view. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Rear view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Installation surface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Installing the washing machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Removing the transit bars . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Re-fitting the transit bars . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
4
Contents
Levelling the machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Screwing out and adjusting the feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Building under a continuous worktop / in a kitchen run . . . . . . . . . . . . . . . . . . 54
Washer and Dryer stack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
The Miele water protection system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Connection to the water supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Connection to the drainage system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Consumption data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Consumption data for the nominated energy labelling programme
according to AS/NZS 2040.1 & AS/NZS 2040.2 Standard . . . . . . . . . . . . . . . . . . 60
Notes for test institutes: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Programmable functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
To access programmable functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
To select a programmable function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
To alter a programmable function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
To come out of programmable functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Language ! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Water plus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Gentle action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Suds cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Temperature unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Buzzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Keypad tone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Standby display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Anti-crease. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Optional accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
CareCollection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
5
Warning and Safety instructions
This washing machine conforms to current safety requirements.
Inappropriate use can, however, lead to personal injury and
damage to property.
To avoid the risk of accidents and damage to the washing
machine, please read these instructions carefully before using it
for the first time. They contain important information on its
installation, safety, use and maintenance.
Keep these instructions in a safe place and ensure that new users
are familiar with the content. Pass them on to any future owner.
Correct application
~ This washing machine is designed for domestic use and for use
in similar environments by guests in hotel or motel rooms, bed &
breakfasts and other typical living quarters. This does not include
common/shared facilities or commercial facilities within hotels,
motels or bed & breakfasts. It must only be used to wash garments
which have been declared suitable for washing by the manufacturer
indicated on the garment care label.
Any other use may be dangerous. The manufacturer cannot be held
liable for damage resulting from incorrect or improper use or
operation.
~ The washing machine is not suitable for outdoor use.
~ This washing machine is not intended for use by persons
(including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have
been given supervision or instruction concerning its use by a person
responsible for their safety.
~ This washing machine must not be installed and operated in
mobile installations (e.g. on a ship).
6
Warning and Safety instructions
Safety with children
~ Keep children away from the washing machine at all times. It is
not a toy! To avoid the risk of injury, do not allow children to play on
or near it or to play with its controls. Supervise children whilst you
are using it.
~ Older children may only use the washing machine if its operation
has been clearly explained to them and they are able to use it
safely, recognising the dangers of misuse.
~ For machines with a 'porthole' door, remember that the porthole
glass will be hot when washing at very high temperatures.
Do not let children touch it.
7
Warning and Safety instructions
Technical safety
~ Before setting up the washing machine, check it for any externally
visible damage.
Do not install or use a damaged washing machine.
~ Before connecting the washing machine, ensure that the
connection data on the data plate (voltage and rated load) match
the mains electricity supply. If in any doubt, consult a qualified
electrician.
~ The electrical safety of this washing machine can only be
guaranteed when continuity is complete between it and an effective
earthing system which complies with current local and national
safety regulations. It is most important that this basic safety
requirement is present and regularly tested and where there is any
doubt, the household wiring system should be inspected by a
qualified electrician. The manufacturer cannot be held liable for the
consequences of an inadequate earthing system (e.g. electric
shock).
~ Do not connect the washing machine to the mains electricity
supply by an extension lead. Extension leads do not guarantee the
required safety of the appliance (e.g. danger of overheating).
~ Faulty components must only be replaced by genuine Miele
original spare parts. Only when these parts are fitted can the safety
standards of the machine be guaranteed.
~ Please refer to the information in "Installation and connection" and
"Technical data".
~ The accesibility of the plug must be always ensured in order to
separate the washing machine from the mains.
8
Warning and Safety instructions
~ Unauthorised repairs could result in unforeseen dangers for the
user, for which Miele cannot accept liability. Repairs should only be
undertaken by a Miele approved service technician.
Ensure current is not supplied to the machine until after
maintenance or repair work has been carried out.
~ If the connection cable is faulty, it must only be replaced by a
Miele approved service technician to protect the user from danger.
~ In the event of a fault or for cleaning purposes, the washing
machine is only completely isolated from the electricity supply when:
– it is switched off at the wall socket and the plug is withdrawn, or
– it is switched off at the mains, or
– the mains fuse is withdrawn, or the screw-out fuse is removed (in
countries where this is applicable).
~ This washing machine must only be connected to the on-site
water supply using a new hose kit. Old hoses must not be re-used.
~ In areas which may be subject to infestation by cockroaches or
other vermin, pay particular attention to keeping the machine and its
surroundings in a clean condition at all times. Any damage which
may be caused by cockroaches or other vermin will not be covered
by the machine warranty.
~ Do not make any alterations to the washing machine unless
authorised to do so by Miele.
9
Warning and Safety instructions
Correct use
~ The maximum load capacity is 7 kg (dry laundry). See the
"Programme chart" for the specific load capacities of individual
programmes.
~ Do not install your washing machine in rooms where temperatures
below freezing may occur. Frozen hoses may burst or split. The
reliability of the electronic control unit may be impaired at
temperatures below freezing point.
~ Before using the washing machine for the first time, check that
the transit bars at the rear of the machine have been removed (see
section on "Installation"). During spinning, a transit bar which is still
in place may result in damage to both the machine and adjacent
furniture or appliances.
~ Turn off the tap if the machine is to be left for any length of time
(e.g. holiday), especially if there is no floor drain (gully) in the immediate vicinity.
~ Flooding danger.
If hooking the drain hose into a wash basin, check that the water can
drain off quickly enough to prevent the sink from overflowing. Make
sure the drain hose is secure, so that the force of the water flowing
out of the hose does not dislodge it.
~ Take care to ensure that foreign objects (e.g. nails, pins, coins,
paper clips) do not find their way into the machine with the laundry.
These may damage components of the machine (e.g. suds
container, drum), which in turn can result in damage to the laundry.
~ The new hose sets supplied with the appliance are to be used.
Old hose sets should not be re-used.
10
Warning and Safety instructions
~ If the correct amount of detergent is dispensed, the machine
should not need to be descaled. If, however, you do wish to descale
the machine, only use Miele Descaler for washing machines and
strictly observe the instructions on the packaging. If in doubt,
contact Miele or your Miele Chartered Agent.
~ Fabrics that have been treated with solvent-based cleaning
agents must be rinsed out in water before washing in the washing
machine.
~ Never use solvent-based cleaning agents, e.g. those containing
benzene, in this machine, as this may result in damage to
component parts and create toxic fumes. Such agents also pose a
fire and explosion hazard.
~ Never use solvent-based cleaning agents, e.g. those containing
benzene, to clean the outside surfaces of this machine. They can
cause damage to plastic surfaces.
~ Dyes need to be suitable for use in your washing machine and
can only be used in domestic quantities. Follow the manufacturer's
instructions carefully.
~ Sulphur compounds in dye removers can cause corrosion. Dye
removers must not be used in the washing machine.
~ If detergent comes into contact with eyes, rinse out immediately
with lukewarm water. If swallowed, see a doctor immediately.
Persons with skin wounds or sensitive skin should avoid contact with
washing detergent.
11
Warning and Safety instructions
Accessories
~ Only use genuine Miele spare parts and accessories with this
appliance.
If non-Miele parts are used, warranty, performance and product
liability claims may be invalidated.
~ Miele tumble dryers can be stacked with Miele washing
machines. To enable this, a stacking kit can be purchased from
Miele as an optional accessory. Please ensure that you order the
correct stacking kit to match the washing machine and tumble dryer
combination.
Miele cannot be held liable for damage caused by noncompliance with these Warning and Safety instructions.
12
Operating the machine
Control panel
a Extra option buttons
Various Extra options can be added
to the washing programmes.
b Display
See the following page for more
information.
c Temperature button
For selecting a temperature.
d Spin speed button
For selecting the final spin speed or
e (Rinse hold) or No . (Without
spin).
e PC / Optical interface
This is used by service technicians
to run diagnostic checks on your
machine and can also be used to
update programming data in the
future.
f Start/Stop button
For starting the programme selected
and cancelling a programme once it
has started.
g Programme selector
For selecting a programme. The
indicator light next to the selected
programme will come on. The
programme selector can be turned
clockwise or anti-clockwise.
h K button
For switching the washing machine
on and off.
To save energy, washing machine
will switch off automatically 15
minutes after programme end/Anti
crease or if no other function is
selected after switching on.
i Door button
Opens the machine door.
13
Operating the machine
Programme duration
After the start of a programme, the
estimated programme duration will
appear in the display in hours and
minutes.
The following are selected via the
display:
– wash temperature
– spin speed
– programmable functions
– cancellation of a programme
– safety lock
The display also shows:
– the programme duration
– the programme sequence
14
During the first 8 minutes the washing
machine measures how much water is
being absorbed by the laundry and
uses this to calculate the load. The
programme duration may be longer or
shorter depending on this absorbency
rate.
Programmable functions
The programmable functions can be
used to tailor washing programmes to
suit your individual requirements. In
programming mode, the display will
show the function selected.
Before using for the first time
Setting the language
Before using the machine for the first
time, ensure that it is correctly
installed and connected. See
"Installation and connection". Also
check that the drain filter is securely
tightened to prevent the risk of water
leaks during use.
This washing machine has
completed a comprehensive
functional test. A small quantity of
water remains in the drum as a result.
For safety reasons, spinning is not
possible until the machine has been
prepared for using for the first time. To
activate the spinning function, you must
run a wash programme without laundry
and without detergent.
Using detergent could result in an
excessive build-up of foam.
This also activates the ball valve. The
ball valve prevents detergent escaping
from the suds container into the sump
during a wash programme, thus making
maximum use of the detergent.
^ Press the K button in.
If the washing machine is being
switched on for the first time, the
welcome screen will appear.
The welcome screen will not appear
again once a programme lasting
longer than 1 hour has been
completed.
You will be asked to select the
language you require for the display. It
is possible to change the language at
any time via the programmable
functions.
!
deutsch
^ Select the language you require by
turning the programme selector.
Confirm your selection by pressing
the Start/Stop button.
Reminder to remove transport struts
To avoid the risk of damage, the
transport struts must be removed
before the machine is used for the
first time. See "Installation and
connection" for instructions on how
to do this.
^ After removing the transport struts (if
this has not already been done by
your fitter), press the Start/Stop
button.
Running your first programme
Run a Cottons r programme without
any laundry and without detergent.
^ Open the tap.
^ Press the Start/Stop button.
^ At the end of the programme, switch
the machine off.
The machine is now ready for use.
15
Washing environmentally and economically
Energy and water consumption
Detergent consumption
– Water consumption and energy
usage are determined by the size of
the load.
To make the most out of your
machine, load the maximum dry load
for the programme you are using.
– Do not exceed the amounts of
detergent recommended by the
manufacturer on the packaging.
– When smaller amounts of laundry are
washed, the automatic load
recognition system will reduce the
amount of water, time and energy
used. This may mean that the time
left shown in the display is adjusted
during the course of the wash
programme.
– Use the Express 20 programme for
small loads.
– Modern detergents enable washing
at reduced temperatures (e.g. 20°C).
Use appropriate temperature
settings for saving energy.
– To maintain hygienic conditions in
the washing machine, it is
recommended that you occasionally
run a wash with a temperature of at
least 60°C. The Hygiene Info
message in the display reminds you
to do this.
– Using the Cottons 40°C programme
is recommended for a normally
soiled load and is the programme
used in energy/water consumption
tests to AS/NZS 2040 (Refer to
consumption data).
16
– Adjust the dosage to the degree of
soiling of the laundry.
– Reduce the amount of detergent with
smaller loads (approx. 1/3 less than
the amount recommended can be
used when washing a half load).
Choosing the correct Extra option
(Short, Pre-wash and Pre-wash +
Soak)
Select:
– A wash programme together with the
Short Extra option for light to normal
soiling where there are no obvious
marks.
– A wash programme without any Extra
options for normal to heavy soiling
with visible staining.
– A wash programme together with the
Pre-wash + Soak Extra option for
heavily soiled laundry.
– The Pre-wash Extra option for
laundry with large amounts of dirt
(e.g. dust, sand).
When drying with a tumble dryer
Selecting the highest possible spin
speed for the wash programme will
save energy when drying in a tumble
dryer afterwards.
How to wash correctly
Brief instructions
The headings numbered A, B, C, . . .
show the operating sequence and can
be used as brief instructions.
A Sort the laundry
,If you use a solvent-based
cleaning agent (e.g. one containing
benzene) to pre-treat a stain, make
sure that any plastic parts (e.g.
buttons) are protected, and that the
cleaning agent is rinsed off before
washing the garment in the
machine.
,Do not use solvent-based
cleaning agents in this machine.
^ Sort the laundry by colour and by
care label. Most garments have a
textile care label in the collar or side
seam.
^ Empty all pockets.
,Foreign objects (e.g. nails,
coins, paper clips, etc.) can cause
damage to garments and
components in the machine.
^ Badly soiled areas, stains etc. should
be cleaned as soon as possible,
preferably whilst still fresh. Spillages
should be carefully dabbed off using
a soft colourfast cloth. Do not rub!
Badly soiled areas can be pre-treated
with liquid detergent, stain removers
etc. first, following the manufacturer's
instructions. With particularly stubborn
stains, ask your dry cleaner for advice.
Dark textiles often contain excess dye
and should be washed separately
several times first. Always wash whites
and coloureds separately.
– Curtains: Remove lead weights first
or place in a laundry bag.
– Underwiring and collar stiffeners:
Any loose wiring in bras, shirt collar
stiffeners, etc. should be removed or
sewn-in.
– Close any zips, fasten hooks and
eyes etc. before washing.
– Fasten duvet covers etc. to prevent
small items from being rolled up
inside them.
Do not wash any items in this machine
which are specified by the
manufacturer as not washable on the
care label (h symbol).
17
How to wash correctly
B Switch on the washing machine
D Select a programme
C Load the drum
^ Press the Door button to open the
drum door.
^ Unfold the laundry and load loosely
in the drum. Mixing both large and
small items gives better wash results
and also helps distribute the load
evenly during spinning.
The most efficient use of energy and
water is achieved when a full load is
washed. However, do not overload as
this causes creases and reduces
cleaning efficiency.
Make sure that no garments are
caught between the drum door and
seal.
^ Turn the programme selector
clockwise or anti-clockwise to select
the required programme. The
programme indicator light for the
programme selected will come on.
E Select a temperature / spin speed
The suggested temperature and/or spin
speed can be changed.
1:49
r
1400
^ Press the Temperature button to alter
the temperature and press the Spin
speed button to alter the spin speed.
^ Shut the door with a gentle swing.
18
How to wash correctly
F Selecting Extra options
Pre-wash+
By pressing the Pre-wash+ button, you
cannot only activate Pre-wash, but also
set an extra soak time of one or two
hours.
Press the button:
Once = Pre-wash
Twice = Pre-wash + 1-hour Soak
3 times = Pre-wash + 2-hour Soak
4 times = switched off
^ Select any Extra options by pressing
the appropriate button. The relevant
indicator light will come on to show
which Extra option has been
selected.
Not all the Extra options are suitable for
use with every programme.
You can only select Extra options which
are compatible with the basic
programme being used.
Short
Extra quiet
You can reduce the noise level of the
washing machine if you want to wash
during rest periods, e.g. at night.
When selecting Extra quiet, the
machine won't spin and Rinse hold is
activated. The programme duration is
longer.
To deactivate Rinse hold
^ Choose the spin speed by pressing
the Spin button.
For light to normal soiling with no visible
staining.
The duration of the main wash is
reduced.
Water plus
The water level in the main wash and
the rinses will be increased if the Water
plus option is selected.
However, you can select other settings
for Water plus. These are described in
"Programmable functions".
19
How to wash correctly
G Add detergent
It is important to dispense the correct
amount, because . . .
. . . too little detergent results in:
– laundry not getting properly clean
and with time it may become grey
and hard to the touch.
– greasy particles clinging to the
laundry.
– limescale deposits on the heater
elements.
. . . too much detergent results in:
– excessive foam which causes a low
level of agitation and poor wash,
rinse and spin results.
^ Pull out the detergent drawer and
place detergent in the compartments
as follows:
i
Detergent for Pre-wash (if selecting
Pre-wash, add 1/4 of the total amount
recommended). This compartment is
also used for starch formulations
when starching separately.
– higher water consumption (an
additional rinse cycle will
automatically switch in).
– a burden to the environment.
j
Detergent for the main wash,
including Soak if selected
§
Fabric conditioners or liquid starch
^ Close the detergent drawer.
See "Detergent" for further information.
20
How to wash correctly
H Start the programme
^ Press the flashing Start/Stop button.
The estimated programme duration will
appear in the display once the
programme has started. During the first
8 minutes the machine measures how
much water is being absorbed by the
laundry. The programme duration may
be longer or shorter depending on this
absorbency rate.
Check that all items have been
removed from the drum. Items left in
the drum could discolour other items
in the next wash or become
discoloured themselves.
The programme sequence is also
shown in the display. The washing
machine shows you when each section
of the programme is reached.
I Remove the laundry when the
programme has finished
In the anti-crease phase after the
programme has finished, the following
will appear in the display:
0:00
Finish
^ Press the Door button to open the
drum door.
The machine will switch off
automatically 15 minutes after the
end of the Anti-crease phase. Push
the K button to switch the machine
back on.
^ Check the folds in the door seal for
any small articles, e.g. buttons, which
might be lodged there.
^ Switch the machine off with the
K button.
To avoid the build-up of mildew, it is
recommended that the door is left
ajar when the machine is not in use.
^ Remove the laundry.
21
Spinning
Final spin speed
To omit the final spin (Rinse hold)
Proofing
1000
Express 20
1400
^ Press the Spin speed button to
choose the Rinse hold setting. The
laundry will not be spun and will
remain suspended in the final rinse
water. This reduces creasing if the
laundry is not going to be removed
from the drum immediately after the
end of the programme.
Automatic plus
1200
– To start the final spin:
Darks and denim
1200
Shirts
600
Programme
rpm
Cottons
1400
Minimum iron
1200
Delicates
600
Woollens /
1200
Intensive plus
1400
Spin
1400
Separate rinse/Starch
1200
The washing machine will display the
maximum spin speed possible. You
can select a lower spin speed. Start
the final spin by pressing the Start/
Stop button.
– To end the programme:
You can reduce the final spin speed.
However, you cannot select a final spin
speed higher than that shown in the
chart above.
Rinse and interim spin
There is a spin after the main wash and
between the rinses. A reduction in the
final spin speed will also reduce the
interim spin speed. For the programme
Cottons with a spin speed of less than
700 rpm, an additional rinse is
introduced.
22
Press the Door button. The water will
drain away. Press the Door button
again to open the door.
To omit rinse and interim spin and
the final spin (No .)
^ Press the Spin speed button to
choose the No . setting.
The water will drain away and the
machine will go straight into the anticrease stage.
An additional rinse is introduced for
some programmes in this setting.
Programme chart
Cottons
Item
Cold to 90°C
Max. load 7.5 kg
Cottons, linens or cotton mixed fabrics, e.g. table linen, towelling,
underwear, T-shirts etc.
Minimum iron
Cold to 60°C
Max. load 3.5 kg
Item
Synthetics, mixed fibres and easy care cottons.
Note
Reduce the spin speed for fabrics which crease easily.
Delicates
Cold to 60°C
Max. load 2.5 kg
Item
For delicate garments made of synthetic fibres, mixed fibres and
rayon.
Curtains, including net curtains, specified as machine-washable by
the manufacturer.
Notes
– Dust in curtains usually makes using a programme with a prewash advisable.
– For items which crease easily, deselect the spin.
Woollens /
Cold to 40°C
Max. load 2.0 kg
Item
Machine-washable or hand-washable wool or wool blend fabrics. If
the care label does not specify a temperature, wash using the cold
setting.
Note
Reduce the spin speed for fabrics which crease easily.
Proofing
40°C
Max. load 2.5 kg
Item
For treating microfibre fabrics, skiwear, fine, closeweave cotton
garments (poplin) or tablecloths to provide a water and dirt resistant
finish.
Notes
– The items should be freshly washed and spun or dried before
proofing.
– For best results, the items should be heat-treated afterwards,
either in a tumble dryer or by ironing.
23
Programme chart
Express 20
Cold to 40°C
Item
Cotton items that are only lightly soiled.
Note
The Extra option Short is automatically activated.
Automatic plus
Cold to 40°C
Max. load 3.5 kg
Max. load 5.0 kg
Item
Mixed loads of garments suitable for the Cottons and Minimum iron
programmes. Sort according to colour.
Note
The wash parameters (e.g. water level, wash rhythm and spin
speed) are adjusted automatically in this programme to ensure the
best possible care and wash result for each item.
Darks and denim
Cold to 60°C
Max. load 3.0 kg
Item
Black and dark garments made from cotton, mixed fibres and
denim.
Notes
– Wash inside out.
– Denim often contains excess dye and will run during the first few
washes. Wash light and dark coloured items separately.
Shirts
Notes
24
Cold to 60°C
Max. load 2.0 kg
– Pre-treat collars and cuffs if necessary.
– Wash silk garments on the Delicates programme.
Programme chart
Intensive plus
Cold to 90°C
Max. load 7.0 kg
Item
Mixed loads of garments suitable for the Cottons and Minimum iron
programmes. Sort according to colour.
Notes
– The Extra Pre-wash function is automatically activated.
– The main wash cycle is extended.
Spin
Notes
– Drain only: Set spin speed to No ..
– Make sure you select the appropriate spin speed.
Separate rinse/Starch
Max. load 7.0 kg
Item
– For rinsing handwashed items.
– Table cloths, napkins and overalls that require starching.
Notes
– Reduce the spin speed for items which crease easily.
– Laundry that is to be starched should be washed but not treated
with fabric conditioner.
– To achieve particularly good rinsing results with two rinse cycles,
the Water plus Extra option should be selected. When selecting
Water plus, the Extra rinse option needs to be activated.
25
Extra options
Selectable Extra options:
iet
qu
ak
tr a
So
Ex
h+
as
-w
P re
h
as
-w
P re
s
plu
ter
Wa
ort
Sh
Cottons
X
X
X
X
X
Minimum iron
X
X
X
X
X
Delicates
X
X
X
X
Woollens /
X
Proofing
Express 20
X
X
1)
X
X
Automatic plus
X
Darks and denim
X
Shirts
X
Intensive plus
X
X
X
X
X
X
X
X
X2)
X
Spin
Separate rinse/Starch
X
X
X1) = Extras that are preset by the programme
X2) = Extras that are preset by the programme cannot be deselected
26
Garment care label symbols
Washing
The figure quoted in the tub is the
maximum temperature the garment
can be washed at.
Drying
The number of dots indicates the
drying temperature
q
Normal temperature
r
Low temperature
s
Do not tumble dry
9
No bar under the symbol =
normal agitation
4
One bar under the symbol =
reduced agitation
c
Two bars under the symbol =
much reduced agitation
/
Hand wash (If no temperature
is specified, use the lowest
temperature or cold)
I
approx. 200°C
H
approx. 150°C
Do not wash
G
approx. 110°C
J
Do not iron
h
Ironing
The number of dots indicates the
ironing temperature
Examples of programme selection
Programme
Care label
Cottons
9ö8E76
Minimum iron
54321
Delicates
ac
Woollens /
/
Express 20
76
Automatic plus 7621
Professional cleaning
f
p
Dry clean only. The letters
indicate the type of cleaning
agent required.
w
Professional Wet Clean only
D
Do not dry clean
Bleaching
x
Any oxidising bleaching
agent can be used
{
Only use an oxygen-based
bleach or a non-chlorine
bleach
z
Do not bleach
27
Programme sequence
Main wash
Rinses
Spinning
Water
level
Wash
rhythm
Water
level
Rinses
Interim
spin
Final
spin
Cottons
d
a
(
2-32)
L
L
Minimum iron
(
c
e
2-33)
L
L
Delicates
e
d
e
3
–
L
Woollens /
e
f
e
2
L
L
Proofing
(
d
–
–
–
L
Express 20
d
b
d
1-33)
L
L
Automatic plus
(
abc
e
3)
2-3
L
L
Darks and denim
(
b
d
3
–
L
Shirts
e
c
e
2
–
L
Intensive plus
(
a
(
2-41)2)
L
L
Spin
–
–
–
–
–
L
Separate rinse/
Starch
–
–
e
1
–
L
See the next page for legend.
28
Programme sequence
d = Low water level
( = Medium water level
Special features in the programme
sequences:
e = High water level
Anti-crease:
a
= Intensive rhythm
b
= Normal rhythm
c
= Gentle rhythm
d
= Sensitive rhythm
e
= Ultra sensitive rhythm
The drum will continue to rotate for up
to 30 minutes after the programme end
to avoid creasing. Exceptions: There is
no crease protection in the Woollens
programme.
The washing machine door can be
opened at any time.
f
= Handwash rhythm
This machine has fully electronic
controls with automatic load
recognition. It takes in the right amount
of water required for the programme
depending on the amount of laundry
and its absorbency rate. This means
that programme cycles and durations
can vary.
The programme sequences outlined in
the chart are based on the basic
programme with a full load. Extra
options which can be selected have not
been taken into account.
1)
Two rinses are carried out if a
temperature selected is between
60°C to 90°C. Three rinses are
carried out if the temperature
selected is below 60°C.
2)
A third rinse is carried out if:
– there is too much foam in the drum
– a spin speed lower than 700 rpm has
been selected
– No . has been selected
3)
A third rinse is carried out if:
No . has been selected
The display shows the stage the
programme has reached.
29
Changing the programme sequence
Cancelling a programme
Changing a programme
You can cancel a programme at any
time after it has started.
After the start of a programme, it is no
longer possible to select a different
programme.
^ Press the Start/Stop button.
Cancel programme
Temperature
^ Press the flashing Start/Stop button
again.
It is possible to select a different
temperature up to 5 minutes after the
programme has started.
The suds will be pumped away.
If you want to remove the laundry:
^ Press the Temperature button.
^ Press the Door button.
Spin speed
If you want to select a different
programme:
It is possible to change the spin speed
up until the final spin begins.
^ Switch the machine off with the
K button.
^ Press the Spin speed button.
^ Switch the washing machine back on
again.
^ Select and start a new programme.
Interrupting a programme
^ Switch the machine off with the
K button.
To continue with the same programme:
^ Switch the machine back on with the
K button.
30
Extra options
It is possible to select or deselect the
Short and Water plus Extra options up
to five minutes after the programme has
started.
A programme cannot be cancelled
or changed if the safety lock has
been activated.
Changing the programme sequence
Adding or removing laundry
after a programme has started
^ Press the Door button to open the
drum door.
^ Add or remove items.
^ Close the drum door.
The programme will continue
automatically.
Please note:
Once a programme has started, the
machine cannot recognise any
adjustment to the load.
For this reason, if laundry is added or
removed after the start of a programme,
the machine will always complete the
programme cycle assuming a full load
which can lead to an increase in the
programme duration shown in the
display.
Safety lock
The safety lock prevents the machine
from being opened, the programme
from being cancelled or the machine
from being switched off during a
wash programme.
To activate the safety lock
^ Press and hold in the Start/Stop
button after the programme has
started.
Stop or in 3 secs 0
^ Keep the Start/Stop button pressed in
until the time has elapsed and the
following appears in the display:
Locked 0
The safety lock is now activated. It is
deactivated automatically at the end of
the programme.
The door cannot be opened, if:
To deactivate the safety lock
– the suds temperature is above 55°C.
^ Press and hold in the Start/Stop
button after the programme has
started.
– the water is above a certain level.
– the programme has reached the
Final spin stage.
– the safety lock has been activated.
If you press the Door button when the
above conditions are present, the
following will appear in the display:
:
Unlock in 3 secs 0
^ Keep the Start/Stop button pressed in
until the time has elapsed and the
following appears in the display:
Unlocked 1
Door locked
31
Detergent
The correct detergent
All modern detergents produced for automatic front loading washing machines
are suitable. Refer to the manufacturer's label on the packaging to get information
on the use and the dosage.
Detergent Detergent Detergent Special Proofing Fabric
for
for
for
detergent agent** softener
universal coloured delicates
*
fabrics*
fabrics*
Cottons
X
X
–
–
–
X
Minimum iron
X
X
–
–
–
X
Delicates
X
X
X
–
–
X
Woollens /
–
–
–
X
–
X
Proofing
–
–
–
–
X
–
X
X
–
–
–
X
X
X
–
–
–
X
X
X
X
–
–
X
Shirts
X
X
–
–
–
X
Intensive plus
X
X
–
–
–
X
Separate rinse/
Starch
–
–
–
X
–
X
Express 20
1)
Automatic plus
Darks and denim
32
1)
Detergent
1)
Use liquid detergent
Use powder detergent
* Miele special detergents:
Washing detergents which were specifically designed for certain programmes
or items (e.g. Miele CareCollection).
** Only use proofing agents which are stated by the manufacturer as being
"suitable for use on membrane textiles" as these consist of fluorochemical
compounds. Do not use proofing agents which contain paraffin. Fill the
detergent drawer § with proofing agent.
2)
All modern detergents produced for automatic front loading washing machines
are suitable. Use dispensing aids, e.g. balls, if these are supplied with the
detergent. Tablets are suitable for full loads, but note that it may be impractical to
reduce tablets for smaller loads. Some tablets do not dissolve as rapidly as
others, and may not be suitable for programmes with short durations.
Do not use biological detergents on silk as the enzymes may damage the silk!
Instructions for use and recommended dosage amounts are given on the
detergent packaging.
For programmes without Pre-wash or Delay start, liquid detergent can either be
dispensed placing a ball-shaped container (commonly provided by the detergent
manufacturer) straight onto the laundry load or alternatively dispensed through
the detergent dispenser drawer. For programmes with Pre-wash or Delay start
(where applicable), an additional liquid detergent dispenser insert (Material
number 6134691) is available from Miele.
33
Detergent
The right amount to dispense will
depend on the following:
– The quantity of laundry.
– The soiling level of the laundry.
Lightly soiled
No visible dirt or stains. Possibly
slight body odour.
Normally soiled
Visibly dirty and/or just a few slight
stains.
Heavily soiled
Stains and soiling clearly visible.
– The water hardness level.
– Check with your local water supplier
if you do not know the water
hardness level in your area.
Water softeners
A water softener can be used to cut
down on the use of detergents in hard
water areas. Dispense according to the
amount specified on the packaging.
First add detergent and then the water
softener.
Use a quantity of detergent as for soft
water.
Washing with several
components
If you wash using several components
(e.g. special application detergents),
dispense them into compartment j in
the following order:
1. Detergent
2. Water softener
3. Stain remover
This way the agents are distributed
more efficiently.
34
Detergent
Fabric conditioners and liquid
starch
Starch
stiffens and gives body to items of
laundry, e.g. shirts, tablecloths and bed
linen.
Fabric conditioners
make garments soft to handle and help
prevent static cling when tumble
drying.
Automatic dispensing of fabric
conditioner or liquid starch to
laundry at the end of a programme
If starching frequently, thoroughly
clean the dispenser compartment,
especially the siphon tube and
fabric conditioner channel, regularly.
See "Cleaning the detergent
dispenser drawer". Do not use
powder starch formulations or
viscous liquid starch in the
compartment as it will clog up.
Adding fabric conditioner or starch
separately
^ Dispense in accordance with
manufacturer's instructions on the
packaging.
^ Add powder or viscous starch to
compartment i. Add the fabric
conditioner or liquid starch to
compartment §.
^ Turn the programme selector to
Separate rinse/Starch.
^ Select a spin speed.
^ Press the Start/Stop button.
^ Add the fabric conditioner or the
liquid starch to compartment §. Do
not exceed the maximum level
mark.
It will be automatically dispensed in the
last rinse. At the end of the programme
a small amount of water remains in the
fabric conditioner compartment §.
Colour run and dye removers/
dyes
^ Do not use colour run or dye
removers in this machine.
^ Dyes suitable for use in domestic
washing machines can be used.
However, please note that the salt
used in the dyeing process can
cause corrosion to stainless steel
components in the machine if you
dye frequently. Follow the
manufacturer's instructions carefully.
35
Cleaning and care
Cleaning the drum (Hygiene
Info)
If you only wash at low temperatures or
with liquid detergent over a long period
of time, organic deposits and
unpleasant odours can form in the
machine. To clean the drum and
prevent the formation of unpleasant
odours, the Cottons 75°C programme
should be run with a universal
detergent at least once a month or
when the message Hygiene Info
appears in the display.
Cleaning the external casing
and fascia panel
,Disconnect the machine from the
mains electricity supply and
withdraw the plug from the socket
before cleaning the machine.
,Do not use solvents, abrasive
cleaners, glass cleaners or allpurpose cleaning agents.
These might damage plastic
surfaces and other components
because of the chemicals they
contain.
Cleaning the detergent
dispenser drawer
The two main detergent compartments
of the dispenser drawer are selfcleaning.
The entire drawer should be removed
and cleaned regularly for hygienic
reasons.
,The washing machine must not
be hosed down.
^ Clean the casing with a mild nonabrasive cleaning agent or soap and
water. Wipe dry with a soft cloth.
^ The drum can be cleaned using a
suitable proprietary stainless steel
cleaning agent following the
manufacturer's instructions on the
packaging.
^ Pull out the detergent dispenser
drawer until a resistance is felt. Press
down the release catch and at the
same time pull the drawer right out of
the machine.
^ Clean the detergent drawer with
warm water.
36
Cleaning and care
^ Clean the siphon.
1. Remove the siphon from
compartment § and rinse under
warm running water. Clean the
siphon tube in the same way.
2. Replace the siphon.
Cleaning the detergent dispenser
drawer housing
^ Use a bottle brush to remove
detergent residues and limescale
from the jets inside the detergent
dispenser drawer housing.
If starching frequently, thoroughly
clean the siphon and siphon tube
regularly. A build-up of starch will
cause them to become clogged.
37
Cleaning and care
Cleaning the water inlet filters
The washing machine has two filters to
protect the inlet valves.
These filters should be checked every
six months or so, or more often if there
are frequent interruptions to the water
supply.
To clean the filter in the water inlet
valve
^ Using pliers, carefully loosen the
ribbed plastic nut on the inlet valve
and unscrew.
To clean the filter in the union in the
open end of the inlet hose:
^ First turn off the tap.
^ Unscrew the threaded union
connecting the free end of the inlet
hose to the tap.
^ Use water pump pliers to withdraw
the plastic filter by the bar (see
illustration). Clean, put back and
secure.
The two filters must be put back in
place after cleaning.
^ Remove the rubber seal 1 from the
recess.
^ Using pointed pliers, take hold of the
plastic filter bar 2, remove the filter
and clean.
^ Put the filter and seal back in the
reverse order and reconnect the
hose.
^ Turn on the tap and check the
connection is watertight.
38
Problem solving guide
What to do if . . .
With the help of the following notes, minor faults in the performance of the
machine, some of which may result from incorrect operation, can be put right
without contacting Miele. Please note that a call-out charge will be applied for
unnecessary service visits where the problem could have been rectified as
described in these Operating instructions.
,Repair work to electrical appliances should only be carried out by a
suitably qualified person in accordance with current local and national safety
regulations. Repairs and other work by unqualified persons could be
dangerous. The manufacturer cannot be held liable for unauthorised work.
The programme does not start
Problem
The display remains
dark, and the Start/
Stop button indicator
light does not come
on.
Possible cause
There is no power to
the machine.
Remedy
Check whether
– the mains plug is plugged
in and switched on.
– the fuse or circuit breaker
has tripped.
You are asked to enter Access via a code has Enter the code and confirm
a code.
been activated.
the entry. Deactivate the code
if you do not wish this
message to appear in the
display the next time the
machine is switched on.
The display is dark.
The display has
switched off
automatically to save
energy (Standby
mode).
Press a button. Standby
comes to an end.
39
Problem solving guide
The following fault message appears in the display and the
programme has been cancelled.
Fault message
Possible cause
Remedy A
;
Drain
fault
– The water outlet is
blocked or restricted.
– The drain hose has
been fixed too high.
;
Water inlet
fault
The water inlet is blocked Check whether
or restricted.
– the tap has been opened
properly.
– the inlet hose is kinked.
– the water pressure is too
low.
;
Waterproof
fault
The water protection
system has reacted.
– Close the tap.
– Call Miele.
;
Technical
fault
There is a fault.
Start the programme again.
If the fault message appears
again, contact Miele.
– Clean the fluff filter and
drain pump.
– The maximum drain height
is 1 m.
A To switch off the fault message: Switch the machine off with the K button.
40
Problem solving guide
The following message appears in the display
Fault message
Possible cause
Remedy
Chk detergent
Excessive foam has built
up during washing.
Use less detergent next time
and follow the manufacturer's
instructions on dosage given on
the packaging.
Hygiene info
A programme of at least Run the Cottons 75°C
60°C has not been run for programme with a universal
a long period of time.
detergent to prevent the
formation of organic deposits
and unpleasant odours in the
machine.
The messages appear at the end of a programme and when the washing machine
is switched on.
41
Problem solving guide
General problems
Problem
Possible cause
Remedy
The machine shakes
during the spin cycle.
The machine feet are
not level.
The laundry has not
been spun properly
and is still wet.
The machine detected Include both large and small
an imbalance during the items in the load as this will
final spin and reduced give better distribution.
the spin speed
automatically.
The laundry has not
spun satisfactorily.
The spin speed
selected was too low.
The pump makes
strange noises.
This is not a fault! These noises occur at the end of a
pump sequence as a normal part of the operation.
There is a lot of
detergent residue in
the detergent drawer.
The water pressure is
too low.
– Clean the water inlet filter.
– Select Water plus.
Clean the siphon, (see
"Cleaning and care Cleaning the detergent
dispenser drawer").
A different language has Set the language you want.
The flag symbol will guide
been selected in the
Programmable functions you.
- Language ! menu.
When laundry is dry, it Too vigorous wash
feels hard to the touch. action.
42
Select a higher spin speed
next time.
Powder detergent used Add washing powder and
with water softeners can then add the water softener.
be sticky.
The siphon tube is not
Fabric conditioner is
correctly positioned or is
not completely
dispensed or too much clogged up.
water remains in the §
compartment.
The display is in a
different language.
Level the machine (see
"Installation").
Programme in gentle action
and more water.
Not enough detergent
used.
Increase detergent dose to
prevent limescale build-up in
laundry.
No fabric conditioner
used
Use fabric conditioner in last
rinse.
Problem solving guide
An unsatisfactory wash result
Problem
Possible cause
Remedy
Liquid detergent
does not give the
required result.
Liquid detergents do not – Use a general purpose
contain bleaching
detergent containing a
agents. They do not
bleaching agent.
remove fruit, coffee and – Add stain remover to the
tea stains.
compartment j.
– Never put stain removers
and liquid detergent together
in the dispenser drawer.
Grey, greasy
particles cling to
washed laundry.
Insufficient amounts of
detergent were used.
The laundry was heavily
soiled with grease.
White residues
which look like
powder detergent
are seen on dark
textiles after
washing.
The detergent contained – Try and brush off the
residues with a soft brush
compounds (zeolites) to
aid water softening
once the laundry is dry.
which are not soluble in – Wash dark textiles using a
water. These have stuck
detergent which contains no
to fabrics.
zeolites. Liquid detergents
usually contain no zeolites.
– Use the Dark garments
programme.
– Use more detergent.
– Before washing the next
load, run a Cottons 60°C
programme with liquid
detergent but without a load.
43
Problem solving guide
The drum door does not open when you press the Door button
Possible cause
Remedy
The machine is not
Insert the plug in the socket and switch on and/or
connected to the
switch the machine on with the K button.
electricity supply and/or is
not switched on.
The safety lock has been
activated.
Deactivate the safety lock as described in
"Changing the programme sequence - Safety
lock".
Access via a code has
been activated.
Deactivate the code as described in
"Programmable functions - Code".
Power cut.
Open the drum door as described in the next
section.
The door was not correctly Press hard against the lock side of the drum door
engaged.
and then press the Door button.
There is still water in the
drum and the machine is
unable to drain.
Clean the drain filter and drain pump as described
in the next section.
For safety reasons, the drum door cannot be opened if the suds temperature is
higher than 55°C.
44
Problem solving guide
Opening the drum door in the
event of a blocked drain outlet
and/or power failure
^ Switch the washing machine off.
There is a filter flap opener behind the
detergent drawer fascia panel.
Blocked drain outlet
If the drain outlet is clogged, more
water will be retained in the machine
(up to 25 litres).
,Caution: If laundry has been
washed at a high temperature, water
draining out of the machine will still
be hot. Danger of scalding!
Procedure for draining the machine
^ Place a suitable container under the
access flap.
When draining water from the
machine, do not unscrew the drain
filter completely or take it right out.
^ Remove the opener.
^ Turn the drain filter lid round until
water runs out.
^ Use it to open the access flap.
To interrupt the flow of water:
^ Tighten the drain filter back up again.
45
Problem solving guide
Once the flow of water ceases:
,Make sure the drain filter is
securely tightened. Otherwise there
is a risk of water leakage during use.
To activate the ball valve and prevent a
loss of washing detergent, pour approx.
2 litres of water through the detergent
dispenser drawer after cleaning the
drain filter.
Opening the drum door
^ Remove the drain filter completely.
^ Clean the drain filter thoroughly.
^ Remove any foreign objects (e.g.
buttons, coins, etc.) and fluff. Turn
the impeller by hand to check that it
rotates freely. Any foreign object
causing an obstruction should be
removed.
^ Put the drain filter back in place and
secure.
46
,Always make sure that the drum
is stationary before reaching into the
machine to remove laundry.
Reaching into a moving drum is
extremely dangerous.
^ Pull the emergency release
downwards (see illustration). The
drum door will open.
After sales service
In the event of any faults which you
cannot remedy yourself, please
contact:
– Miele (see back cover for contact
details).
When contacting Miele, please quote
the model and serial number of your
appliance, both of which are shown on
the data plate visible at the top inside
the door above the porthole glass when
the door is open.
Future updates (PC)
The indicator light marked PC allows a
service technician to update your
machine in future years.
If, for example, new programmes are
developed or new fabrics are
introduced, a Miele service technician
will be able to modify existing
programme cycles accordingly.
Miele will provide information when
such developments become available.
Appliance warranty
The appliance has a manufacturer's
warranty of 2 years.
See the warranty card supplied with the
machine for further details.
Optional accessories
Optional accessories for these washing
machines are available from Miele.
Please note that telephone calls may
be monitored and recorded to
improve our service.
47
Installation and connection
Front view
a Inlet hose (tested to withstand
pressure of at least 7000 kPa)
b Electricity supply cable
c - f Flexible drain hose (with
detachable swivel elbow)
g Facia panel with controls
h Detergent dispenser drawer
i Drum door
j Flap for fluff filter, drain pump and
emergency release
k Handle recesses for moving the
machine
l Four height adjustable feet
48
Installation and connection
Rear view
a Protruding lid for holding when
moving the machine
e Transport brackets for inlet and drain
hoses
b Electrical connection
f Transit bar covers
c Inlet hose (tested to withstand
pressure of at least 7,000 kPa)
g Transport brackets for inlet and drain
hose and restraining clips for transit
bars
d Drain hose
49
Installation and connection
Installation surface
Installing the washing machine
A concrete floor is the most suitable
installation surface for a washing
machine, being far less prone to
vibration during the spin cycle than
wooden floorboards or a carpeted
surface.
To manoeuvre the machine out of its
packing case to its installation site, hold
it by the edge of the lid where it
protrudes to the rear of the washing
machine as well as by the handle
recesses at the front.
Please note:
^ The machine must be level and
securely positioned.
^ To avoid vibrations during spinning,
the machine should not be installed
on soft floor coverings.
,Ensure that the machine feet and
the floor are dry to prevent the
machine from slipping during the
spin cycle.
Removing the transit bars
If installing on a wooden joist floor:
^ We recommend a plywood base (at
least 59x52x3 cm). The base should
span several joists and be bolted to
the joists and not only to the
floorboards. Check for the presence
of pipes and cables first.
If possible, install the machine in a
corner as this is usually the most stable
part of the floor.
,If the machine is installed on a
raised plinth, it has to be secured
against slippage during spinning
using retaining clips (available from
Miele).
50
^ To remove the left and right covers
1. Pull off the transit bar covers and
2. use a screwdriver to prise out the
covers.
Installation and connection
^ Using the spanner supplied, turn the
left-hand transit bar 90°, then
^ Turn the right-hand transit bar 90°,
then
^ withdraw the transit bar.
^ withdraw the transit bar.
51
Installation and connection
,To avoid the risk of injury, the
holes for the transit bars must be
covered after the transit bars have
been removed.
^ Secure the transit bars to the back of
the washing machine. Make sure that
the upper hooks are above the
retainers.
^ Fit the covers onto the two holes.
,The machine must not be moved
without the transit bars in place.
Store them as shown or keep them
in a safe place for future use. They
must be re-fitted if the machine is to
be moved again (e.g. when moving
house).
Re-fitting the transit bars
Re-fitting is carried out by reversing the
procedure.
52
Installation and connection
Levelling the machine
The machine must stand perfectly level
on all four feet to ensure safe and
proper operation.
Failure to level the machine can result
in the machine "banging" in the spin
cycle or "walking" across the floor
during operation.
Screwing out and adjusting the feet
The four adjustable screw feet are used
to level the machine. All four feet are
screwed in when the machine is
delivered.
^ Use a spirit level to check the
machine is standing level.
^ Hold foot 1 securely with a pipe
wrench. Turn counter nut 2 again
using the spanner supplied until it
sits firmly up against the housing.
,All four counternuts must be
firmly up against the housing. Please
also check this for the feet which did
not need adjustment. Otherwise
there is the danger of the machine
moving about.
^ Using the spanner supplied, turn
counter nut 2 in a clockwise
direction. Then turn counter nut 2
together with foot 1 to unscrew.
53
Installation and connection
Building under a continuous
worktop / in a kitchen run
– A special building under conversion
kit* is required.
The machine lid must be replaced by
a cover plate. To ensure electrical
safety, the cover plate must be
fitted. **
Washer and Dryer stack
A Miele tumble dryer can be stacked
with the washing machine. A stacking
kit* is necessary and can be purchased
from Miele.
Please note
N.B.**
If you wish to push your machine under
a worktop and there is space to do this
without removing the lid, the
conversion kit is not necessary.
Otherwise the conversion kit is
essential.
– For installation under a work surface
900/910 mm from the floor, a raising
kit* is required.
– Connections for electricity, water and
drainage should be installed in such
a way that they remain accessible
when the machine is in place.
Fitting instructions are supplied with the
conversion kit.
a Safety distance to wall:
at least 2 cm
All parts marked* are available from
Miele.
b Height:
Stacking kit with pull-out shelf:
approx. 169 cm
Stacking kit without pull-out shelf:
approx. 170 cm
The fitting of cover plates and
stacking kits must only be
undertaken by qualified and
competent persons, in accordance
with the instructions supplied with
the kit.
54
,A washer and dryer should
never be stacked without using the
proper stacking kit. Doing so is
extremely dangerous as the dryer
may vibrate off of the washing
machine during use.
Installation and connection
The Miele water protection
system
The Miele water protection system
protects all parts of the washing
machine from water damage.
The system consists of three main
components:
1) the inlet hose
2) the electronic unit and the washing
machine housing
3) the drain hose
– Overflow protection
This prevents the washing machine
taking in too much water. If the water
level exceeds a certain level, the
drain pump switches in and pumps
the excess water away.
3) Drain hose
The drain hose is protected by a
ventilation system which prevents the
washing machine from being
emptied completely.
1) Inlet hose
– The inlet hose can withstand
pressure of more than 7000 kPa.
2) Electronic unit and washing
machine housing
– Sump
Any leaking water is collected in a
sump in the base of the machine. A
float switches off the safety valves,
preventing any more water flowing
into the machine and water in the
suds container is pumped away.
55
Installation and connection
Connection to the water
supply
IMPORTANT: Australia and New
Zealand
This appliance must be installed
according to AS/NZS 3500.1.
Backflow prevention is already
integrated in the appliance.
The machine should be connected to a
mains water supply in accordance with
current local and national safety
regulations.
The machine is designed to operate
with a flow pressure of between
100 kPa and 1000 kPa. If it is higher
than 1000 kPa, it is essential to fit a
pressure reducing valve.
Connection to the mains water supply
should incorporate a mains tap with 3/4"
thread. The tap should be fitted by a
qualified plumber.
,The connection point is subject
to mains water pressure. Turn on the
tap slowly and check for leaks.
Correct the position of the washer
and union if appropriate.
The washing machine is not suitable
for connection to a hot water supply,
and connection to a household
water softener is not recommended.
56
Maintenance and care
Only use a genuine Miele hose should
you ever need a replacement or
extension. These are tested to
withstand pressure of at least 7000 kPa.
In order to protect the water inlet
valve, the two dirt filters - one in the
open end of the inlet hose, one at
the inlet point in the machine- must
not be removed.
Extension hose
– Longer hoses 2.5 or 4.0 m in length
are available from Miele as optional
extras.
This appliance incorporates backflow
protection complying with ATS
5200.101. No further backflow
protection is required for connection to
the water supply.
Installation and connection
Connection to the drainage
system
Please note:
The machine drains via a drain pump
with a delivery head of 1 metre*. The
drain hose must not be kinked as this
restricts drainage. The swivel elbow at
the end of the hose can be turned in
either direction, or can be detached if
required, with a sharp twist and pull.
If required, the drain hose can be
extended to a length of 5 m. The
necessary parts can be purchased
from Miele.
* For a delivery head more than 1 m (up
to a max. of 1.8 m), a second duo-drain
pump is available with the
corresponding kit from Miele.
a Adapter*
b Nut*
c Hose clip*
d End of the hose
Drain hose connection:
1. Direct into a sink or basin:
Please note the following:
– Hook the hose over the edge and
secure.
– Make sure that the water can drain
away freely without hindrance.
Otherwise there is a risk of water
overflowing or of some of the drained
water being sucked back into the
machine.
^ Fit adapter a to the sink drain outlet
using nut b.
^ Attach the end of the hose d to
adapter a.
^ Use a screwdriver to tighten hose
clip c up close to the nut.
* Not supplied with washing machine.
2. Connected securely to a plastic
drain pipe with a rubber nipple.
There is no need to use a non-return
valve.
3. Connected securely to a standpipe.
4. Connected securely to a floor gully.
57
Installation and connection
Electrical connection
The washing machine is supplied with a
mains cable with moulded plug for
connection to a 230V mains supply.
The voltage, rated load and plug rating
are given on the data plate. Please
ensure these match the household
mains supply.
The accesibility of the plug must always
be ensured in order to separate the
washing machine from the mains.
All electrical work should be carried out
only by a suitably qualified and
competent person, in strict accordance
with national and local safety
regulations.
For extra safety, it is advisable to install
a residual current device (RCD), with a
trip current of 30 mA.
Ensure power is not supplied to the
appliance until after installation work
has been carried out.
Connection should be made via a
suitable switching socket which is
easily accessible after installation in
order to separate the washing machine
from the mains.
Do not connect via an extension lead.
Extension leads do not guarantee the
required safety of the appliance (e.g.
danger of overheating).
WARNING: THIS APPLIANCE
MUST BE EARTHED
58
Technical data
Height
850 mm
Width
595 mm
Depth
610 mm
Depth with door open
993 mm
Height for building under
820 mm*
Width for building under
600 mm
Depth for building under
600 mm
Weight
98 kg
Capacity
7.5 kg dry laundry
Voltage
See data plate
Rated load
See data plate
Fuse rating
See data plate
Consumption data
see "Consumption data"
Water flow pressure minimum
100 kPa (1 bar)
Water flow pressure maximum
1000 kPa (10 bar)
Inlet hose length
1.60 m
Drain hose length
1.50 m
Connection cable length
1.60 m
Drain pump head max.
1.00 m
Drain pump length max.
5.00 m
LEDs
Class 1
Test certificates awarded
See data plate
Power consumption when machine is
switched off
0.25 W
Power consumption in standby mode
2.0 W
* Including building under kit. See "Installation and connection".
59
Consumption data
Consumption data for the nominated energy labelling
programme according to AS/NZS 2040.1 & AS/NZS 2040.2
Standard
Load
Cottons
s
7.5 kg
Consumption data
Energy
Water
Duration
in kWh
in litres
Normal Cold
Water
0.56
62
2 h 24 min
Notes for test institutes:
– Detergent must be dispensed via the detergent dispenser drawer.
Consumption data can vary from the nominal values given depending on water
pressure, water hardness, water inlet temperature, room temperature, type and
volume of load, fluctuations in the electricity supply and any Extra options
selected.
60
Consumption data
Load
Cottons
Consumption data
Energy
Water
in kWh
in litres
Duration
Residual
moisture
90°C
7.5 kg
2.20
55
2 h 19 min
50%
r
7.5 kg
1.05
55
2 h 09 min
50%
r
3.5 kg
0.64
45
1 h 12 min
50%
s*
7.5 kg
0.56
62
2 h 24 min
–
s
3.5 kg
0.45
45
59 min
50%
Minimum iron
40°C
3.5 kg
0.50
50
1 h 08 min
30%
Delicates
30°C
2.0 kg
0.38
69
59 min
–
Woollens /
30°C
2.0 kg
0.23
39
39 min
–
Proofing
40°C
2.5 kg
0.35
12
40 min
–
Express 20
40°C
3.5 kg
0.32
30
20 min
–
Automatic plus
40°C
5.0 kg
0.52
62
1 h 29 min
–
Darks and denim
40°C
3.0 kg
0.60
52
1 h 12 min
–
Shirts
60°C
2.0 kg
0.95
59
1 h 12 min
–
Intensive plus
60°C
7.0 kg
1.65
72
2 h 47 min
–
Note for test institutes:
*
AS/NZS 2040.1 & AS/NZS 2040.2
Consumption data can vary from the nominal values given depending on water
pressure, water hardness, water inlet temperature, room temperature, type and
volume of load, fluctuations in the electricity supply and any additional options
selected.
Cottons temperatures denoted by a border (r/s) indicate labelling
programmes as designated by European Union standards only. For labelling
parameters conforming to AS/NZS 2040.1 & AS/NZS 2040.2, please refer to the
previous page of this booklet.
61
Programmable functions
To alter a programmable function
The programmable functions are
used to alter the machine's
electronics to suit changing
requirements. Programmable
functions can be altered at any time.
To access programmable functions
The programmable functions are
accessed via the Start/Stop button
and the programme selector.
Before you begin, first ensure that:
– The washing machine is switched off.
– The machine is properly closed.
A Press the Start/Stop button and keep
it pressed in whilst carrying out steps
B-C.
B Press the K button in.
C As soon as . . .
Language !...
. . . appears in the display, release
the Start/Stop button.
To select a programmable function
D Turn the programme selector until
the programmable function you
require appears in the display.
E Press the Start/Stop button to confirm
your selection.
62
You can see the different options
available for a programmable function
by turning the programme selector.
The option which is currently set will
have a tick L beside it.
F Turn the programme selector until
the option you want appears in the
display.
G Press the Start/Stop button to
activate this option.
To come out of programmable
functions
H Turn the programme selector until
Back A appears in the display.
I Press the Start/Stop button.
Language !
The display can be set to appear in
one of several different languages.
The flag ! after the word Language acts
as a guide to prevent a language which
will not be understood from being set.
The language selected is saved to
memory.
Programmable functions
Water plus
This programmable function is used
to select the water intake setting for
the Water plus Extra option.
There are three different options:
Water +
(the machine is delivered with this
option selected)
The water level is increased in the wash
and rinse stages.
Extra rinse
An extra rinse is introduced.
Water + and Extra rinse
The water intake is increased in the
wash and rinse stages and an extra
rinse is carried out.
Gentle action
Activating gentle action reduces the
drum action and is suitable for
washing slightly soiled items more
gently. It should be activated for
garments with a single bar under the
care label and for articles which feel
too hard after they have been dried.
Gentle action can be activated for the
Cottons and the Minimum iron
programmes.
The washing machine is delivered with
the Gentle action setting deactivated.
Suds cooling
When this is activated, additional
water flows into the drum at the end
of the main wash to cool the suds
down. Hot suds can damage plastic
drainage pipes.
Suds cooling takes place when
temperatures of 90°C and 75°C are
selected.
Suds cooling should be activated:
– to prevent the danger of scalding if
the drain hose is hooked over the
edge of a sink or basin.
– where the drainage pipes do not
comply with DIN 1986.
The machine is delivered with Suds
cooling deactivated.
63
Programmable functions
Code
A code can be used to lock the
electronics on the washing machine
to prevent it being used without your
knowledge.
When the code has been activated, you
have to enter a code after switching the
washing machine on. Otherwise the
washing machine cannot be operated.
Code ...
1
2
5
^ Press the Start/Stop button.
The following will appear in the display:
Code activated
Once the machine is switched off, it
can only be used again if the code is
entered.
^ Press the Start/Stop button.
To use the washing machine when
the code is activated
To activate the code
When the machine is switched on
again, the display will request the code.
Activate
^ Press the Start/Stop button.
^ Enter code 125 as described above
and confirm the entry.
The display will now request that a
code is entered.
The washing machine is now unlocked
and ready for use.
To enter the code
To deactivate the code
The code is 125 and cannot be altered.
Make sure the washing machine is
switched off and the door is properly
closed. Press the Start/Stop button and
keep it pressed in whilst you press the
l-On/0-Off button in.
O
__ __
^ Turn the programme selector until the
first number appears in the display.
^ Confirm your selection of the number
by pressing the Start/Stop button.
^ Repeat the process until all three
numbers have been entered.
As soon as . . .
O
__ __
. . . appears in the display, release
the Start/Stop button.
^ Now enter the code and press the
Start/Stop button.
Select Code and confirm Deactivate.
64
Programmable functions
Temperature unit
You can choose for the temperature
to be displayed in °C/Celsius or
°F/Fahrenheit.
The machine is delivered with °C/
Celsius as the default setting.
Keypad tone
An audible tone sounds each time a
button is pressed.
The machine is delivered with the
keypad tone deactivated.
Brightness
Buzzer
When the buzzer function has been
activated, an audible tone sounds at
the end of a programme or when
Rinse hold is reached.
There are two volumes:
There are ten different display
brightness settings.
The bar chart shows you the setting.
The machine is delivered with the
display brightness on setting 5.
Off
This will change as soon as a different
setting is chosen.
(the machine is delivered with this
option selected as standard)
Contrast
The buzzer is switched off.
There are ten different display
contrast settings.
Normal
The buzzer sounds at normal volume at
the end of a programme or when Rinse
hold is reached.
Loud
The bar chart shows you the setting.
The machine is delivered with the
display contrast on setting 5.
This will change as soon as a different
setting is chosen.
The buzzer sounds at loud volume at
the end of a programme or when Rinse
hold is reached.
65
Programmable functions
Standby display
To save energy, the display goes out
after 10 minutes and the indicator
light for the Start/Stop button will start
flashing slowly.
There are two options:
On
Standby is activated:
Memory
If an Extra option has been selected
for a programme, or the
recommended temperature or spin
speed has been altered, the machine
will store the changes in memory at
the start of a programme.
When this programme is chosen again,
these settings will appear in the
display.
– if a programme is not selected within
10 minutes of the machine being
switched on.
The machine is delivered with the
memory function deactivated.
– after a programme has started.
Anti-crease
– at the end of a programme.
Not in current prog.
(the machine is delivered with this
option selected)
Standby is activated:
– if a programme is not selected within
10 minutes of the machine being
switched on.
– at the end of a programme.
Pressing one of the buttons switches
the display back on again.
Anti-crease helps prevent creasing if
laundry is not normally removed immediately after the end of a
programme.
The drum will turn at intervals for up to
30 minutes after the programme has
finished.
The door can be opened and laundry
removed at any time during the anticrease phase.
On
Anti-crease is activated.
Off
(the machine is delivered with this
option selected)
Anti-crease is deactivated.
66
Optional accessories
Miele washing machines offer perfect
care for your laundry and feature a
wide range of special programmes
designed to suit the fabric being
washed. And now Miele have
developed a range of specialist
CareCollection detergents and
conditioning products to offer you a
complete package for cleaning and
caring for your laundry.
The Miele CareCollection detergents
and conditioning products are listed
below. You can order these and many
other useful products via the internet at:
All the products can also be ordered
from Miele (see back cover for contact
details).
CareCollection
Miele specialist detergents
Fabric softener
Miele's fabric softener will give your
laundry a fresh, natural fragrance. It
makes garments soft to handle and
prevents static build-up during tumble
drying.
For delicates
This liquid detergent is ideal for the
gentle treatment of delicate fabrics,
such as wool and silk. Its special
formulation cleans effectively at
temperatures as low as 20°C, while
protecting the colour of your delicate
garments.
UltraWhite
This multi-purpose powder detergent
has excellent stain removal properties
and is suitable for white and light
coloured laundry as well as heavily
soiled coloured items.
Sensitive skin
Miele’s sensitive skin laundry detergent
has been specifically tested and
formulated for consumers with sensitive
skin and allergies. This detergent is
powerful and deep cleaning for optimal
stain removal, even at 40°C, leaving
your laundry with a fresh, mild
fragrance.
67
Optional accessories
UltraColor
Available in a liquid and powder form,
this detergent is particularly suitable for
cleaning coloured and dark garments.
The special formulation offers effective
stain removal, even at low
temperatures, while helping to prevent
colours fading.
Sportswear
The Miele sportswear detergent is
designed to clean sportswear whilst
taking care of the special microfibres
used in these garments. It will help to
neutralise and remove odours whilst
protecting the colour of the fabric and
preventing static build-up.
Down Items
This special-purpose detergent
contains a mild tenside and has been
specially formulated to keep down-filled
items supple and to give them bounce.
68
69
70
71
0LHOH$XVWUDOLD3W\/WG
!".
A]Y`Y7YbhYfUbX<YUXCZZ]WYAY`VcifbY.
'ILBERT0ARK$RIVE
+NOXFIELD6)#
A]Y`Y7YbhYfUbXCZZ]WYAY`VcifbY.
#OVENTRY3TREET
3OUTH-ELBOURNE6)#
A]Y`Y7YbhYfUbXCZZ]WYGmXbYm.
3KYLINE0LACE
&RENCHS&OREST.37
A]Y`Y7YbhYfUbXCZZ]WY6f]gVUbY.
(ARVEY3TREET.ORTH
%AGLE&ARM1,$
A]Y`Y7YbhYfUbXCZZ]WY5XY`U]XY.
3IR$ONALD"RADMAN$RIVE
(ILTON3!
A]Y`Y7YbhYfUbXCZZ]WYDYfh\.
3TIRLING(IGHWAY
#LAREMONT7!
0LHOH1HZ=HDODQG/LPLWHG
<YUXCZZ]WY.
5NIT,3YLVIA0ARK2OAD
-T7ELLINGTON!UCKLAND
A]Y`Y7YbhYf5iW_`UbX.
#OLLEGE(ILL
&REEMANS"AY!UCKLAND
4ELEPHONE
-)%,%
WWWMIELECONZ
ZZZPLHOHFRPDX
Alteration rights reserved/2414
0LHOH*OREDO+HDGTXDUWHUV
*HUPDQ\
0LHOH&LH.*
#ARL-IELE3TRA”E
'àTERSLOH
&EDERAL2EPUBLICOF'ERMANY
M.-Nr. 09 493 620 / 02