Zoom | Gateway/Router V3 | User manual | Routers configuration Guide for Digimerge Digital

Add to my manuals
39 Pages

advertisement

Zoom | Gateway/Router  V3 | User manual | Routers configuration Guide for Digimerge Digital | Manualzz
Router configuration Guide
Rev.1b
1
Routers configuration Guide
for Digimerge Digital Video
Recorders and Network devices
Digimerge Technologies Inc.
300Alden Road • Markham • Ontario • Canada • L3R4C1
tel: (905)946-8477 • fax: (905)947-0138
Router configuration Guide
Rev.1b
2
Table of Contents
INTRODUCTION. ....................................................................................................................................................................... 4
THE ROUTER CONFIGURATION.......................................................................................................................................... 4
PORT FOWARDING AND DMZ OPTIONS............................................................................................................................ 5
BEFORE YOU START .................................................................................................................................................................... 5
1. THE PORT FORWARDING RULES. ............................................................................................................................ 5
2. THE DMZ feature. ........................................................................................................................................................... 6
LIST OF PORTS FOR DIGIMERGE NETWORK DEVICES ............................................................................................... 7
ROUTERS SECTION .................................................................................................................................................................. 8
LINKSYS....................................................................................................................................................................................... 9
BEFDSR41W, BEFN2PS4, BEFSRU31, BEFSRU31, BEFSR41 V1& V2, BEFSR V2FW 1.40.2, BEFSR41 V3 V4 & V5,
BEFSR81, BEFSX41, BEFSX41-CA, BEFVP41 V1&V2, BEFVP41-CA, BEFW11S4, BEFW11S4 V2,V3, & 3.2,
BEFW11S4 V4, BEFW11S4-CA V2 & V4, WRT51AB, WRT55AG ........................................................................................ 9
LINKSYS. WIRELESS .............................................................................................................................................................. 11
BEFSR41-CA, BEFSX41 V1.50, BEFW11S4 V1.50.10, BEFW11S4 V1.50.14, RT31P2, WAG54G, WRK54G, WRT54G,
WRT54G V1.1 V2 & CA, WRT54G V2.04, WRV54G, WRV54G-CA.................................................................................... 11
DLINK ........................................................................................................................................................................................ 13
MODELS DI-514, DI-524, DI-604, DI-614+, DI-624, DI-704P (REVB), DI-704P (REVC), DI-704UP, DI-707P, DI-714P+,
DI-754, DI-764, DI-774, DI-784, DI-804HV, DI-808HV, AND DI-824VUP: .......................................................................... 13
SMC ............................................................................................................................................................................................. 14
2804WBRP-G, 2804WBR V1, V2, 7804WBRB.................................................................................................................... 14
ACTIONTEC ............................................................................................................................................................................. 15
GT701-WG, GT704WR, R1020S, R1020S(U), R1520SU, R1524SU-1.................................................................................. 15
NETOPIA ................................................................................................................................................................................... 17
CAYMAN 3300 ....................................................................................................................................................................... 17
WESTELL DSL MODEM/ROUTER...................................................................................................................................... 19
B90-2200- 30-05 ( BELLSOUTH ) ............................................................................................................................................. 19
2200 ( VERIZON ) ..................................................................................................................................................................... 22
VERSALINK 327W .................................................................................................................................................................... 22
BELKIN...................................................................................................................................................................................... 24
F5D5231-1 ............................................................................................................................................................................... 24
NETGEAR .................................................................................................................................................................................. 26
RP614V1 & V2, WGR614, WGT624V1 & 2, .......................................................................................................................... 26
DG824M V1.3........................................................................................................................................................................ 27
2 WIRE ....................................................................................................................................................................................... 28
1000HW, 1000S, 1000SW, 1800HG......................................................................................................................................... 28
Digimerge Technologies Inc.
300Alden Road • Markham • Ontario • Canada • L3R4C1
tel: (905)946-8477 • fax: (905)947-0138
Router configuration Guide
Rev.1b
3
ZOOM......................................................................................................................................................................................... 30
X4 5551.................................................................................................................................................................................... 30
EFFICIENT (SIEMENS) .......................................................................................................................................................... 32
SPEEDSTREAM 5100,5200, 5400, 5500 .................................................................................................................................... 32
ZYXEL ....................................................................................................................................................................................... 33
ZYWALL1, ZYWALL2WE, ZYWALL2, ZAWALL10, ZYWALL100............................................................................................... 33
UNICOM WIRELESS .............................................................................................................................................................. 34
GIGAFAST ................................................................................................................................................................................ 35
EE-400-R ................................................................................................................................................................................. 35
APPENDIX A.............................................................................................................................................................................. 36
HOW TO ACCESS THE ROUTER CONFIGURATION SCREEN ....................................................................................... 36
APPENDIX B.............................................................................................................................................................................. 37
SELECTING AND ASSIGNING AN IP ADDRESS FOR YOUR NETWORK DEVICE. ..................................................... 37
TROUBLESHOOTING ............................................................................................................................................................. 39
Digimerge Technologies Inc.
300Alden Road • Markham • Ontario • Canada • L3R4C1
tel: (905)946-8477 • fax: (905)947-0138
Router configuration Guide
Rev.1b
4
INTRODUCTION.
The purpose of this manual is to help distributors, installers and customers in general to configure
their routers for use with a network device such a digital video recorder, video server etc. Our goal is to
provide enough information to configure the router and successfully connect to the cameras over the
internet. This manual shows most common router models on the market. If your router it is not listed in
the manual identify the other routers listed and see if there is a similar one. Let us know if your router is
not listed so we may add it in future revisions.
THE ROUTER CONFIGURATION.
The router configuration screen is the last step in the process to view and access the cameras over the
Internet (WAN). The connection and configuration will depend from the network topology, configuration
and environment. Most digital video recorders and Network devices commonly are connected in a Local
Area Network (LAN) and the Router is connected usually to a DSL modem or cable modem. The Router
configuration is vital to connect properly to the internet and view the cameras from a remote location.
ROUTER with a 4 ports switch in a WAN / LAN environment.
ROUTER with 4 PORT
embedded switch
DVR
WAN
LA
N
A router is a device that forwards data packets along networks. A router is connected to at least two networks,
(Internet)
Router :
commonly two LANs or WANs or a LAN and its ISP network. Routers are located at gateways, the places where two or more
networks connect, and are the critical device that keeps data flowing between networks and keeps the networks connected to
the Internet. When data is sent between locations on one network or from one network to a second network the data is always
seen and directed to the correct location by the router. They accomplish this by using headers and forwarding tables to
determine the best path for forwarding the data packets; and they use protocols such as ICMP to communicate with each other
and configure the best route between any two hosts. The Internet itself is a global network connecting millions of computers and
smaller networks — so you can see how crucial the role of a router is to our way of communicating and computing.
Digimerge Technologies Inc.
300Alden Road • Markham • Ontario • Canada • L3R4C1
tel: (905)946-8477 • fax: (905)947-0138
Router configuration Guide
Rev.1b
5
PORT FOWARDING AND DMZ OPTIONS
Before you start working with your router is important to :
1. Assign a static IP address and select the ports to your network device( * ) , ( See Appendix
B for more information ).
2. Have ready your router (gateway) IP address to access the router menus ( See appendix A for
more information).
3. Have the port list ready according with your product needs to create the forwarding rules. ( See
page 7 with all products listed).
The information provided in this manual is to guide and help the customer create forwarding rules or
port forwarding for specific ports on a router.
There are to ways to work with the router ports. The procedure may vary with the router manufacturer
option screens. The two options are:
1 . PORT FORWARDING RULES
2. THE DMZ
1. THE PORT FORWARDING RULES.
In order to allow users to access your Network Device ( * ) on the Internet (WAN) we need to create
forwarding rules . That means we need to open ports on the Router and forward ( Port forwarding ) the
data from a specific IP address . Once the Router has the ports opened the data will pass-through the
Router . Every router internally works and interacts with two IP addresses. One is the internal IP address
or gateway. The one works with your LAN and the other one is the external IP for the internet
communications.
When a Network Device sends data to a remote router on the internet , the router receive the
information and needs to know what to do with the data. The port forwarding feature what it does is to
tells the router where to send the data with the computer or network device attached to the LAN.
( * )Network device: Any IP addressable device or electronic equipment connected in a LAN such a
Digital video recorder, video server or computer.
When you create and enable the ports on the router ( The term is referred as forwarding rules) , the
router takes the data off the external IP address:port number ( this is called a socket) and sends that
data to an internal IP address:port number. The port forwarding rules are created per port.
Example using port 2000 : When the router receives the data from the external IP address, the
router works with the internal NAT ( Network address translation) and communicates the information from
the external IP to the internal IP address. The information from a distant router comes with a specific
Digimerge Technologies Inc.
300Alden Road • Markham • Ontario • Canada • L3R4C1
tel: (905)946-8477 • fax: (905)947-0138
Router configuration Guide
Rev.1b
6
forwarding rule and that rule contains information related to port 2000. That means the internal IP
address (gateway) on your LAN will communicate only with the network device on the LAN configured
to receive the data for port 2000. If you have one network device working with port 2000, only this
device will be able to use port 2000. That means only a port number can be used for a program or
network device. For example if you have a customer using 2 video servers connected on the same LAN ,
you have to give each one a different port to communicate on the same network or over the internet.
2. THE DMZ feature. ( demilitarized zone )
This feature allows you to open all the ports at once in your router for your Network device IP
address. The DMZ takes the IP address of the device on your network and forwards all ports. This is
really a nice feature if you are having problems forwarding ports for some program or device. It can be a
life saver if your router will not allow you to properly forward ports. The Network Device with the DMZ
enabled is now wide open to internet traffic. If the network device attached to the router is a Digital video
recorder or a Video server for example , the unit will not be able to catch a virus, or risk being hacked
because these units are stand alone and designed with an embedded operating systems. On the other
hand there is a risk if you are using a computer instead. If you are using a computer on your LAN it is
better to forward the ports only and not use the DMZ option.
The router #2 is been configured to do port
forwarding for the port 2000 for the internal IP
address 192.168.1.125 on the LAN . The router
# 2 has the port 2000 open. When the user from
router #1 access the video server, the data will
go directly to the local IP 192.168.1.125 using
port 2000
ROUTER #1
INTERNET
If the user has installed the network
viewer application to view the
camera .The application will try to
` IP address from router
access the
#2. ( 24.116.50.6 )
The network viewer application must
have the IP from router #2 address
( 24.116.50.6) and the port 2000 to
view the camera..
External IP : 24.116.50.6
ROUTER #2
ROUTER #2
192.168.1.125:2000
Broadband
Modem
WAN
Broadband
Modem
This figure shows an example of how a user access
a video server/camera from a remote location
using the IP from Router #2 and port 2000 on a
a PC
For a more detailed explanation of the port forwarding procedures visit :
http://www.portforward.com/help/portforwarding.htm
Digimerge Technologies Inc.
300Alden Road • Markham • Ontario • Canada • L3R4C1
tel: (905)946-8477 • fax: (905)947-0138
Router configuration Guide
Rev.1b
7
LIST OF PORTS FOR DIGIMERGE NETWORK DEVICES
FAMILY
DGR200
Series
MODELS
201, 204
PORTS
80, 1080, 2080
DGN200
Series
209,
216
Any
Video server
D4202
Any
DHT300-400
Series
VCD300
Series
304,308,316
404, 409, 416
304, 308,
309
4 ports needed
TCP Ports
Log On . 7000 ( * )
Live transmission :8000-8001 ( * )
Remote Playback: 9000-9001 ( * )
Automatic connection when alarm
is activated :8003
Checking server alive:8002 ( * )
Time sync : 3000-8900 ( * )
Two way audio : 7010-7011-7021
Web port : 80,2000 ( * )
DDNS Server : 10101, 43300 ( 1 )
COMMENTS
Default port is 80
Fixed port
Only one port is needed.
Default port is 80.
Only one port is needed.
Suggested alternated port : 2000
Default port is 80.
Only one port is needed.
Suggested alternated port : 2000
Default ports are: 5000-5003
Fixed ports.
Web port is 80 and 2000.
* Mandatory ports
(1 )These ports are used to work
with the DDNS server
UDP ports
11000 ( 1 )
4 channel PCI
Video capture
card
QDR0450
4 channel USB
video capture
card
QDU470
•
4 ports needed
Any port from a range from
2000-65000
4 ports needed
Any port from a port range from
2000-65000
Default ports:
• Video port :2000
• Audio port: 2001
• PTZ control : 2002
• Remote Search :2003
Default ports:
• Video port :2000
• Audio port: 2001
• PTZ control : 2002
• Remote Search :2003
Note : Port 80 is the http port for the Internet browser and it is usually blocked by the Internet
Service Provider. We recommend using a different port like 2000 to avoid possible problems.
Digimerge Technologies Inc.
300Alden Road • Markham • Ontario • Canada • L3R4C1
tel: (905)946-8477 • fax: (905)947-0138
Router configuration Guide
Rev.1b
ROUTERS SECTION
This section shows the procedure to create port forwarding rules.
The information is presented by manufacturer and model.
Digimerge Technologies Inc.
300Alden Road • Markham • Ontario • Canada • L3R4C1
tel: (905)946-8477 • fax: (905)947-0138
8
Router configuration Guide
Rev.1b
9
LINKSYS
BEFDSR41W, BEFN2PS4, BEFSRU31, BEFSRU31, BEFSR41 V1& V2, BEFSR V2FW 1.40.2,
BEFSR41 V3 V4 & V5, BEFSR81, BEFSX41, BEFSX41-CA, BEFVP41 V1&V2, BEFVP41-CA,
BEFW11S4, BEFW11S4 v2,v3, & 3.2, BEFW11S4 V4, BEFW11S4-CA v2 & v4, WRT51AB,
WRT55AG
Log in to the Router's Web-based Utility. (This is
usually done by opening your web browser,
entering 192.168.1.1 in the Address field ( or
your “default gateway” IP address from your
PC ), and pressing the Enter key. You should
see the following screen.
On the left hand side put the name of the
application.
Application name: can be any description of your
Network Device attached on you LAN
You are forwarding ports in the Customized
Application box.
In the Ext. Ports box put the port ranges you
wish to forward. If you are unsure of the port
range/ranges check the Ports list page or the
network device (*) model you are working with.
Example :
For port 1080, start with port 1080, and end
with port 1080.
Press the STATUS Tab and write the WAN IP
address for future reference for the remote
connection .
To open the ports press on the ADVANCE tab
on the top and Select Port Range Forwarding
Check on the protocol type TCP, UDP, or just
both. Check both if you are unsure of the
protocol type. In the IP Address box, enter your
Network device(*) IP address
Click the Enable check box on the right hand
side.
If you have more ports continue with the next
line.
Click Apply at the bottom of your screen to save
your changes
(*) See page 5 for more information
Digimerge Technologies Inc.
300Alden Road • Markham • Ontario • Canada • L3R4C1
tel: (905)946-8477 • fax: (905)947-0138
Router configuration Guide
DISABLE BLOCK WAN REQUEST
FEATURE.
Rev.1b
DMZ OPTION
Press the Advance tab and select the
Filters tab.
If you don’t want to enable the port range
forward feature you can use the DMZ
option to open all the port at once.
Click and disable the Block Wan request
feature.
Click on the Advance tab on the top
When finish click on Apply to save the
changes.
Click on the DMZ Host option
Enter your network device (*) IP
address and press apply.
(*) See page 5 for more information
Digimerge Technologies Inc.
300Alden Road • Markham • Ontario • Canada • L3R4C1
tel: (905)946-8477 • fax: (905)947-0138
10
Router configuration Guide
Rev.1b
11
LINKSYS. wireless
BEFSR41-CA, BEFSX41 V1.50, BEFW11S4 v1.50.10, BEFW11S4 v1.50.14,
RT31P2,
WAG54G, WRK54G, WRT54G, WRT54G v1.1 v2 & CA, WRT54G v2.04, WRV54G, WRV54GCA
Log in to the Router's Web-based Utility. (This is
usually done by opening your web browser,
entering 192.168.1.1 in the Address field ( or
your “default gateway” IP address from your
PC ), and pressing the Enter key.) You should
see the following screen.
On the left hand side put the name ** of the
application. You are forwarding ports in the
Application box.
** Application name: can be any description of
your Network Device attached on your LAN
In the Start and End boxes put the port ranges
you wish to forward. If you are unsure of the port
range/ranges check the Ports list page or the
network device model you are working with.
Example :
For port 1080, start with port 1080, and end
with port 1080.
Press the STATUS Tab and write the WAN IP
address for future reference for the remote
connection .
To open the ports press on the Applications
and Gamming Tab on the top. Click on Port
Range Forward Option
Check the protocol type TCP,UDP, or just both.
Check both if you are unsure of the protocol
type.
In the IP Address box, enter your
Network Device (*) IP address to forward the
ports to.
Click the Enable check box on the right hand
side.
If you have more ports continue with the next
line.
Click Save Settings at the bottom of your
screen to save your changes
(*) See page 5 for more information
Digimerge Technologies Inc.
300Alden Road • Markham • Ontario • Canada • L3R4C1
tel: (905)946-8477 • fax: (905)947-0138
Router configuration Guide
DISABLE BLOCK WAN REQUEST
FEATURE.
Press the SECURITY tab
Click and disable the Block Wan request
feature.
When finish click on Save Settings to
save the changes.
12
Rev.1b
DMZ OPTION
If you don’t want to enable the port range
forward feature you can use the DMZ
option to open all the port at once.
Click on the APPLICATIONS
GAMMING Tab on the top.
Click on the DMZ option
Enter your local network device IP
address and press Save Settings
Digimerge Technologies Inc.
300Alden Road • Markham • Ontario • Canada • L3R4C1
tel: (905)946-8477 • fax: (905)947-0138
AND
Router configuration Guide
Rev.1b
13
DLINK
Models DI-514, DI-524, DI-604, DI-614+, DI-624, DI-704P (revB), DI-704P (revC), DI-704UP,
DI-707P, DI-714P+, DI-754, DI-764, DI-774, DI-784, DI-804HV, DI-808HV, and DI-824VUP:
Open your web browser and enter the IP address of
your router (192.168.0.1). Enter username (admin)
and your password (leave blank).
Enter the private network device (*) IP address into
the Private IP box.
Select the protocol type from the Protocol type drop
down box. If you are unsure of the protocol type
select both if available. If both is not an option you
would need to create a duplicate configuration, one
with TCP selected the other with UDP selected.
Enter the private port into the Private Port box.
Generally you should enter the same port into the
Public Port box. For port information check the Ports
list page or the Network Device (*) model
Press the STATUS Tab and write the WAN IP
address for future reference for the remote
connection .
To open the ports press on the ADVANCE Tab on
the top. Click on Virtual Server Option
Enter the name of the service (Ex. Your DVR
description) you are trying to forward ports for in the
Name box.
Example using port 1080 :
• Private Port 1080
• Public Port 1080.
The schedule should be set to Always. Put a dot in
the Enable circle at the top to enable your profile.
If you have more ports continue with the next line.
Click Apply at the bottom of your screen to save
your changes.
DMZ OPTION
If you don’t want to enable the ports feature you can
use the DMZ option to open all the ports at once.
Click on the Advance Tab and Select the DMZ
Option.
Enter your network device local IP address click
on enable and press Apply.
(*) See page 5 for more information
Digimerge Technologies Inc.
300Alden Road • Markham • Ontario • Canada • L3R4C1
tel: (905)946-8477 • fax: (905)947-0138
Router configuration Guide
Rev.1b
SMC
2804WBRP-G, 2804WBR V1, V2, 7804WBRB
DMZ Option Only
Open a web browser. In the address bar
type the IP address of your router. This IP
address is 192.168.1.2 by default. Press
enter
Step 2:
You should now see a login screen and it
should be prompting you for a password.
We want to log in as administrator, so
enter your administrator password here.
By default the administrator password is
smcadmin. Click the login button to log
into the router.
Step 3:
Click Firewall on the left hand menu. This
will drop down a sub-menu on the left
hand side.
Step 4:
Click DMZ in the left hand menu. This will
open up the screen below.
Step 5:
A Static IP address is need for this function.
Click in the Enable DMZ Yes radial button.
In the Public IP address box, you enter the
network device IP (*) address you wish to
open to the internet.
Click Apply at the bottom of the page.
Click the STATUS menu at the left and
write the WAN Internet IP address for
future reference for the remote connection .
(*) See page 5 for more information
Digimerge Technologies Inc.
300Alden Road • Markham • Ontario • Canada • L3R4C1
tel: (905)946-8477 • fax: (905)947-0138
14
Router configuration Guide
Rev.1b
Actiontec
GT701-WG, GT704WR, R1020S, R1020S(U), R1520SU, R1524SU-1
Enter the IP address of your router in the
address bar of your browser.. By default
the IP address should be set to
192.168.0.1.
Click on Port Forward on the left hand side.
You should see the following menu.
Click setup/configuration. You should
see the following menu.
Enter the following information :
IP Port Range. Enter a port range.
Example : For port 1080, start with port
1080, and end with port 1080.
Click ADVANCE at the side of the menu.
You will see the following menu
- Protocol : Select the protocol type , TCP
or UDP
- IP address : Enter your Network device (*)
IP address.
Click on ADD to add the settings to the box
below.
If you have more ports to open repeat the
procedure.
To finish click on Save and RESTART
(*) See page 5 for more information
Digimerge Technologies Inc.
300Alden Road • Markham • Ontario • Canada • L3R4C1
tel: (905)946-8477 • fax: (905)947-0138
15
Router configuration Guide
DMZ OPTION.
Rev.1b
16
Click on DMZ Hosting option
If you don’t want to use the port forward feature
you can use the DMZ option to open all the
ports at once
Click setup/configuration. You should see the
following menu.
Enter the Network device (*) IP address, Then
you click in the On radial button.
Click ADVANCE at the side of the menu. You
will see the following menu
Now click on Save and Restart on the left hand
side. The following menu should appear.
To finish click Save and Restart.
Click the STATUS menu and write the WAN
Internet IP address for future reference for the
remote connection .
(*) See page 5 for more information
Digimerge Technologies Inc.
300Alden Road • Markham • Ontario • Canada • L3R4C1
tel: (905)946-8477 • fax: (905)947-0138
Router configuration Guide
Rev.1b
NETOPIA
CAYMAN 3300
Enter the IP address of your router in the
address bar of your browser.. By default the
IP address should be set to 192.168.1.254.
Enter your user name and password. By
default the username is admin, and the
password is blank. Click the OK button to log
in to your router.
Click the Expert Mode link on the left hand
side of your screen.
•
Click on CONFIGURE link on the top.
•
Click on the ADVANCE link
On the ADVANCE Network menu click on the
PINHOLES Option.
This menu option will allows you to enable the port
forwarding option.
Click OK to enter the export mode
Click the ADD button to add a new pinhole
configuration to your Router.
Digimerge Technologies Inc.
300Alden Road • Markham • Ontario • Canada • L3R4C1
tel: (905)946-8477 • fax: (905)947-0138
17
Router configuration Guide
Rev.1b
If you finished click on the Alert button.
The Alert button is a Yellow triangle at the left
top area of your menu
Click on SAVE and Restart
-Pinhole Name: your network device
name ( ex DVR, video server , or PC)
-Protocol type: TCP or UDP
-External port start : Enter you start port
-External port end : you end port
Example using port 1080.
External start port 1080
External end port : 1080
- Internal IP address: Enter your Network
device (*) IP address. ( ex DVR , video
server or PC attached)
- Internal port :Enter the lowest port.
.
Example :If you open a range of ports
from 80 to 1080, use 80 as the lowest
port.
Click the Submit button
If you need to open more ports click on the
ADD button and repeat the procedure.
(*) See page 5 for more information
Digimerge Technologies Inc.
300Alden Road • Markham • Ontario • Canada • L3R4C1
tel: (905)946-8477 • fax: (905)947-0138
18
Router configuration Guide
Rev.1b
WESTELL DSL MODEM/ROUTER
B90-2200- 30-05 ( Bellsouth )
Open a web browser like internet explorer or
Netscape
Click the Expert Mode button on the left hand
side of your screen.
Then under Home click the Service
Configuration button on the left hand side of
your screen.
Enter the IP address of your router in the
address bar of your browser. By default the IP
address should be set to 192.168.1.1.
You should see a box prompting you for your
username and password. Enter your username
and password now. By default the username is
blank, and the password is NOLOGIN.
Click the OK button to log in to your router.
In the new menu that appeared under
Configuration, click the NAT button.
Continue on next page…….
.
Digimerge Technologies Inc.
300Alden Road • Markham • Ontario • Canada • L3R4C1
tel: (905)946-8477 • fax: (905)947-0138
19
Router configuration Guide
Rev.1b
Enter a name for the program or device you are
forwarding ports for in the Service Name box. Ex :
DVR
Enter the ports to forward into the Global Port
Range boxes.
Example: for port 2000-2000
Click the Define Customer Service button to
move to the next page
The smallest port number should go into the box on
the left, while the largest port number should go
into the box on the right.
Main port the program uses into the Base Port
box. This is your lower port from your list.
Examples: If you are using only one port like
2000 enter 2000-2000.. If your are using a
range of port like 80-1080, the base port is 80
Select the protocol type using the UDP or TCP
radial buttons.
Click the Next button when you are done
making changes.
Put a dot in the Port Forwarding Ranges of
Ports radial button. Then click next at the
bottom of this page
If you need to add additional ports, click the Add
button.
When you are done adding ports/protocol types,
click the Close button
Continue on Next page….
Digimerge Technologies Inc.
300Alden Road • Markham • Ontario • Canada • L3R4C1
tel: (905)946-8477 • fax: (905)947-0138
20
Router configuration Guide
Rev.1b
Once you finished adding all the ports go back
to the service configuration screen
Use the Service Name drop down box to find
and select the first configuration you just
created for your network device name ( Ex
DVR) .
Then click the Enable button to enable it. You
will need to repeat this step for each service
that you created
Once you press enable the following screen
will appear
Select and find your network device (*) IP
address or enter your IP address to forward
the ports and complete the procedure,
Press Done to finish
(*) See page 5 for more information
Digimerge Technologies Inc.
300Alden Road • Markham • Ontario • Canada • L3R4C1
tel: (905)946-8477 • fax: (905)947-0138
21
Router configuration Guide
Rev.1b
2200 ( Verizon )
Versalink 327W
Open a web browser like internet explorer or
Netscape
Click on Configuration on the top Menu and
Select Service configuration
Enter the IP address of your router in the
address bar of your browser. By default the IP
address should be set to 192.168.1.1
Click the Define Customer Service button to
move to the next page.
You should see a box prompting you for your
username and password. Enter your username
and password now. By default the username is
blank, and the password is NOLOGIN.
Click the Ok button to log in to your router.
Put a dot in the Port Forwarding Ranges of
Ports radial button. Then click next at the
bottom of this page.
Continue on next page…….
Digimerge Technologies Inc.
300Alden Road • Markham • Ontario • Canada • L3R4C1
tel: (905)946-8477 • fax: (905)947-0138
22
Router configuration Guide
Enter a name for the program or device you are
forwarding ports for in the Service Name box.
Ex : DVR , Video server or PC.
Enter the ports to forward into the Global Port
Range boxes.
Rev.1b
If you need to add additional ports or you need
to specify both protocol types, click the Add
button. Then repeat the above steps, and
specify the other protocol or add another port.
Once you finished adding all the ports go back
to the service configuration screen
Example: for port 2000-2000
The smallest port number should go into the
box on the left, while the largest port number
should go into the box on the right.
Main port the program uses into the Base Port
box. This is your lower port from your list.
Examples: If you are using only one port, for
example 2000, enter 2000-2000. Your base
port will be 2000.
Use the Service Name drop down box to
select the first configuration you just created at
your device name (Example: DVR) .
If your are using a range of port like 80-1080
the base port is 80.
Then click the Enable button to enable it. You
will need to repeat this step for each service
that you created
Select the protocol type using the UDP or TCP
radial buttons.
Click the Next button when you are done
making changes.
Once you press enable the following screen
will appear
Select and find your network device (*) IP
address or enter your IP address to forward
the ports and complete the procedure,
Press Done to finish
(*) See page 5 for more information
Digimerge Technologies Inc.
300Alden Road • Markham • Ontario • Canada • L3R4C1
tel: (905)946-8477 • fax: (905)947-0138
23
Router configuration Guide
Rev.1b
BELKIN
F5D5231-1
Open a web browser like internet explorer or
Netscape
In the one titled firewall click Virtual Servers.
This will bring you to the following menu.
Enter the IP address of your router in the
address bar of your browser. By default the IP
address should be set to 192.168.2.1.
You should prompted for your password. Enter
your password now. By default the password is
blank. Click the Ok button to log in to your
router.
We are going to be working in the table
portion of this menu to forward ports. All the
settings to forward a port or series of ports will
go on one line. If you want to forward
additional ports you can fill out a second line
with additional information.
Description box. A good description would be
the name of the network device (*) (Ex DVR)
you are forwarding ports for.
Inbound Port box . Enter the port range. This
range would be specified by entering the
starting port number in the first box under
inbound ports and the ending port number in
the second box under inbound ports. Do the
same thing for the Private Port boxes.
- Type :Select the protocol type . TCP or
UDP or Both .
On the left hand side you will see a series of
four menus.
Note : If you are unsure of the protocol type,
just select both.
Continue on next page…..…
(*) See page 5 for more information
Digimerge Technologies Inc.
300Alden Road • Markham • Ontario • Canada • L3R4C1
tel: (905)946-8477 • fax: (905)947-0138
24
Router configuration Guide
- Enter your network device (*) IP address
you wish to forward in the Private IP Address
box.
-
Rev.1b
DMZ Option
On the Setup screen select DMZ at the left area
of your menu
Put a check in the Enable checkbox..
Click on Apply changes to finish
(*) See page 5 for more information
------------------------
You will see the following menu
Enter your Network Device (*) IP address and
click on enable.
Press Apply changes to finish
(*) See page 5 for more information
Digimerge Technologies Inc.
300Alden Road • Markham • Ontario • Canada • L3R4C1
tel: (905)946-8477 • fax: (905)947-0138
25
Router configuration Guide
Rev.1b
NETGEAR
RP614v1 & v2, WGR614, WGT624v1 & 2,
Open a web browser like internet explorer or
Netscape
On the menu bar to the left under Advanced
click Port Forwarding
You should now be at the Port Forwarding
menu as shown below.
Enter the IP address of your router in the
address bar of your browser. By default the IP
address should be set to 192.168.0.1.
To create a new port forward service click on
Add Custom Service button.
You should see a box prompting you for your
username and password. Enter your username
and password now. By default the username is
admin, and the password is blank. Click the
Ok button to log in to your router
Enter the information requested on the menu.
- Service Name : Enter the description of your
DVR or device or service (PC) . Ex DGR200
-Starting port. Enter the lowest port
-Ending port. Enter the Highest port
-Server IP address: Enter your network
device(*) IP address
- Click Apply at the bottom of the menu to finish.
The basic settings window will be visible
(*) See page 5 for more information
Digimerge Technologies Inc.
300Alden Road • Markham • Ontario • Canada • L3R4C1
tel: (905)946-8477 • fax: (905)947-0138
26
Router configuration Guide
Rev.1b
DG824M V1.3
DMZ Option
Open a web browser like internet explorer or
Netscape
On the menu bar to the left under WAN Setup
Options
You should see the WAN setup menu
Enter the IP address of your router in the
address bar of your browser. By default the IP
address should be set to 192.168.0.1.
You should see a box prompting you for your
username and password. Enter your username
and password now. By default the username is
admin, and the password is blank. Click the
Ok button to log in to your router
Click on Default DMZ server and enter your
network device (*) IP address .
Click on Apply to Save the settings.
(*) See page 5 for more information
The basic settings window will be visible
Digimerge Technologies Inc.
300Alden Road • Markham • Ontario • Canada • L3R4C1
tel: (905)946-8477 • fax: (905)947-0138
27
Router configuration Guide
Rev.1b
2 WIRE
1000HW, 1000S, 1000sw, 1800HG
Open a web browser like internet explorer or
Netscape
Enter the IP address of your router in the
address bar of your browser. By default the IP
Address should be set to gateway.2wire.net
The basic settings window will be visible
Click the Add a new user-defined
application link in the Applications section.
Click on the FIREWALL button on the top
Click FIREWALL SETTINGS in the firewall
menu on the top of the screen
Continue on next page……..
Digimerge Technologies Inc.
300Alden Road • Markham • Ontario • Canada • L3R4C1
tel: (905)946-8477 • fax: (905)947-0138
28
Router configuration Guide
Rev.1b
Enter the following information:
-Application name. Enter the name of the
program ( Ex. Your DVR, video server
description ).
-Protocol: TCP or UDP.
-Port Range . From ( the lowest port)
To ( the Highest port)
-Protocol timeout ( seconds) :
----For TCP enter : 86400
----For UDP enter : 600
-Map to Host port : Leave it empty
-Application type: Set to None
Click ADD Definition to add this definition to
your router.
Select a computer option:. device ( your
network device(*) IP address) or computer
your want to forward.
On the Applications list scroll down and find
the Application you just created and highlight
it.
Click the ADD button to move it to the Hosted
Application box at your right.
Click DONE button at the bottom of the
screen to finish
Note :If you have multiple ports , you have to
create an application for every range of ports
. (*) See page 5 for more information
Click the BACK button at the bottom page to
go back to the previous menu.
Digimerge Technologies Inc.
300Alden Road • Markham • Ontario • Canada • L3R4C1
tel: (905)946-8477 • fax: (905)947-0138
29
Router configuration Guide
Rev.1b
ZOOM
X4 5551
Enter the IP address of your router in the
address bar of your browser. By default the IP
address should be set to 10.0.0.3
You should prompt for your password. Enter
your password now. By default the password is
blank. Click the Ok button to log in to your
router
Click the Advanced Setup button at the top of
your screen. You should now see the following
screen.
Click the Advanced Setup button at the top of
your screen. You should now see the following
screen
Continue on Next page…….
Digimerge Technologies Inc.
300Alden Road • Markham • Ontario • Canada • L3R4C1
tel: (905)946-8477 • fax: (905)947-0138
30
Router configuration Guide
In the middle of this page you will see a NAT
Options drop down box. Click the down arrow
and select NAT Rule Entry
Take note of the Rule ID's that are in use.
Usually you want these rule numbers to
increment by 10. So the new rule you create
should be 10 more than the largest rule number
here. At the bottom of the page click Add. You
should now see another window
Rev.1b
Enter the following Settings
1. Rule Flavor drop down box. Select RDR
from the list.
2. Enter a number in the Rule ID box. This
number needs to be unique, so some
number that was not listed on the services
page.( any number not listed)
3. IF Name box. Select ALL
4. Protocol drop down box : Select the
protocol type of the ports you are
forwarding.(if you don’t know select ALL)
5. Local Address From : Enter your local
device network (*) IP address
6. Local Address To : Enter your local DVR
Ip address
7. Global Address From: Enter 0.0.0.0
8. Global Address To Enter 0.0.0.0
9. Destination Port From : Enter your lower
port of your port range
10. Destination Port To : Enter the highest
port of your port list .
a. Example 80 - 1080
11. Local Port box : Put a zero in it.
12. Click the Save Changes button at the
bottom of your screen.
Once again click on Advance setup button at the
top of your screen .Click on the IP filter button
The Security Level drop down box should be set
to none.
The Private Default Action, Public Default
Action and DMZ Default Action should all be set
to Accept.
Click the submit button at the bottom of the page.
Now we are going to save these changes.
Make sure to write your settings to flash, and
reboot your router before the settings will take
effect.
(*) See page 5 for more information.
Digimerge Technologies Inc.
300Alden Road • Markham • Ontario • Canada • L3R4C1
tel: (905)946-8477 • fax: (905)947-0138
31
Router configuration Guide
Rev.1b
EFFICIENT (SIEMENS)
Speedstream 5100,5200, 5400, 5500
Enter the IP address of your router in the
address bar of your browser. By default the IP
address should be set to 192.168.254.254
Enter your username and password now. By
default both the username and password are
blank. Click the Ok button to log in to your
router.
Select Protocol drop down box. Then enter the
port range in the TCP/UDP Ports box.
At the right side of the screen enter the lowest
port number and highest port number should
go in the box on the right.
Example TCP 80 - 1080
Click the Redirect selected protocol/service
to IP address radio button.
On the main menu click Login. Select admin
from the username drop down box. Enter the
admin password in the Password box. Click
the Okay button to get back to the main menu..
Enter the IP address you wish to forward this
service to in that box. ( your network device
(*) IP address)
Then click Apply to save your changes.
(*) See page 5 for more information
Digimerge Technologies Inc.
300Alden Road • Markham • Ontario • Canada • L3R4C1
tel: (905)946-8477 • fax: (905)947-0138
32
Router configuration Guide
Rev.1b
ZyXEL
Zywall1, Zywall2WE, Zywall2, Zawall10, Zywall100
Enter the IP address of your router in the
address bar of your browser.
By default the IP address should be set to
192.168.1.1
Enter the following information to open the
ports:
-- Check on the Active check box
-Name : Enter the name of your network
device (Example video server)
-Start Port: Enter your lower port of your list
Example: opening ports from 80 to 1080
--- Start port : 80
--- End Port : 1080
End Port: Enter the highest port
Server IP address: Enter your network device
(*) Ip address.
Repeat the procedure to open more ports if
needed.
You should prompted for your password. Enter
your password now. By default the password is
1234. Click the Ok button to log in to your
router. In the left hand menu click SUA/NAT.
Press Apply to finish.
You should now see the following menu.
Digimerge Technologies Inc.
300Alden Road • Markham • Ontario • Canada • L3R4C1
tel: (905)946-8477 • fax: (905)947-0138
33
Router configuration Guide
Rev.1b
UNICOM wireless
DMZ Option only
Click on Internet on the Advanced menu at
left side of the screen.
Enter the IP address of your router in the
address bar of your browser.
Enter your User name and password to access
the main menu (if needed)
To enable the DMZ option, click enable on the
first line.
Select a PC. Click the drop down menu at the
right and locate your network device (*) IP
address.
Press Save to save the settings
Click On the Status menu on the left
Click on LAN at the left side of the menu
Write down your Internet IP address for
reference. Press Restart to save the settings
(*) See page 5 for more information
Digimerge Technologies Inc.
300Alden Road • Markham • Ontario • Canada • L3R4C1
tel: (905)946-8477 • fax: (905)947-0138
34
Router configuration Guide
Rev.1b
GIGAFAST
EE-400-R
DMZ Option only
Enter the IP address of your router in the
address bar of your browser. The default IP
address is 192.168.8.1
Enter your User name and password to access
the main menu. By default the user name is
blank and the password is admin.
By default the DMZ page is disabled. Click the
Enable radio button.
Enter your Network device (*) IP address
on the DMZ menu
Then click the Save and Restart button.
(*) See page 5 for more information
In the menu on the left hand side of your
screen, click Advanced. In the menu under
Advanced click the DMZ link.
Digimerge Technologies Inc.
300Alden Road • Markham • Ontario • Canada • L3R4C1
tel: (905)946-8477 • fax: (905)947-0138
35
Router configuration Guide
Rev.1b
36
Appendix A
HOW TO ACCESS THE ROUTER CONFIGURATION SCREEN .
The Router configuration is the most important step in the process to view the cameras on the Internet. Most of the
routers are similar on the access, graphics interface and configuration. The first step to access the router
configuration screen it is to know the router IP address or “Gateway”. Usually the Web Browser is commonly used
to access the router configuration.
If you don’t know what is your router IP address ( gateway) do the following procedure:
•
Press on Start
•
Click on RUN
•
Type cmd and click OK
DOS command prompt window
In the DOS window type ipconfig and press ENTER
The information from your DOS prompt will show you the information related to your network.
This information will be:
a- Your computer IP address.
b- Your Subnet mask
c- Your Default gateway.
This information includes the Default Gateway IP address. This is the information we need to access the router
menus. Write down this information for later use.
Once you have the router IP address (gateway), open the Internet Explorer and type in the address bar
http://192.168.1.1 and press ENTER
You will see the LOGIN screen. Enter the user name and password to access the Router menus and
configuration. ( if needed) .
Digimerge Technologies Inc.
300Alden Road • Markham • Ontario • Canada • L3R4C1
tel: (905)946-8477 • fax: (905)947-0138
Router configuration Guide
Rev.1b
37
Appendix B
SELECTING AND ASSIGNING AN IP ADDRESS FOR YOUR NETWORK DEVICE.
Selecting an IP address for your network device ( DVR, Video server , PC ) is important. With the IP
address you will be able to communicate on the Network properly. To obtain an IP address for your
Network device try the following options.
1. FROM THE IT ADMINISTRATOR.
1. FROM THE IT ADMINISTRATOR. Medium to large networks are administrated
usually by an IT Administrator. In many cases is recommended to ask what IP address
can be used on your network device ( * ) ( see page 5 for more information )
2. THE “GUESSING “ METHOD”
If it is difficult to get and IP address for the network , this method will help you to find an IP
address easily for your network device ( * ) .
2.1. ADDING A NUMERIC VALUE. First at all, we have to get some information from a
computer connected to the same network. See Appendix A to see how to get the information off
the computer.
Examples.
If the computer connected on the same network has an IP address (example) as 192.168.1.68
, try adding 5 numbers to the last octet ( example , -> 68 + 5 = 73 ) . The resulting number
will be 192.168.1.73 .
2.2 CHECKING THE IP ADDRESS . Once we have an IP address we want to try, we have to
check if someone is using the IP address before we assign it to the Network device ( * ).
Go back to the computer at the DOS prompt windows according with procedure on Appendix A
On the DOS prompt
Type the following command :
ping 192.168.1.73
press ENTER
If you receive a “reply from” that means somebody is already using this IP address on
the network.
( * ) See page 5 for more details…
Digimerge Technologies Inc.
300Alden Road • Markham • Ontario • Canada • L3R4C1
tel: (905)946-8477 • fax: (905)947-0138
Router configuration Guide
Rev.1b
38
Let’s try to use another IP address adding another number to the last octet ( lets add 4
numbers, 73 + 4 = 77 ) and try again. Example 192.168.1.77
Type :
ping 192.168.1.77
press ENTER
If you get a “request timed out” , the message means nobody is using the IP address and this means
you can use it on your network device.
2.3. APPLYING THE SETTINGS. Once we selected the new IP address 192.168.1.77, we will
need to use the same subnet mask and the same default gateway from the computer. In addition to
these values we need to make sure what port needs to be assigned to work properly according with the
listed ports of your network device. ( See page 7 for a complete list ).
The final values ( example) for the Network device will be:
EXAMPLE
IP address
Subnet mask
Default Gateway
192.
255
192.
168.
255
168
1
255
1
77
0
1
Once you assigned the IP address on your network device . Perform a ping command to the device
according with the ping procedure, If you have a reply from your respective device IP address that
indicates your the connection is working properly on the LAN.
Digimerge Technologies Inc.
300Alden Road • Markham • Ontario • Canada • L3R4C1
tel: (905)946-8477 • fax: (905)947-0138
Router configuration Guide
Rev.1b
TROUBLESHOOTING
PROBLEM
SOLUTION
I can’t access the router
configuration screen
•
•
•
Check your cable connections
Check if you entered the correct router (gateway) IP address
Check if your computer has a Firewall blocking the IP address
I can access my router
configuration screen but I
don’t have internet
connection
I opened all the ports on the
router and I can’t still
connect to my remote
Network device (DVR, video
server)
•
If you are using a DSL modem, check if you connection is
down. Call your ISP to solve the problem.
•
•
Check your DSL modem, make sure your connection is UP.
Check the information on your network device has the correct
information: IP address, subnet mask and default gateway
according with the Appendix A.
Check if you opened the correct ports.( see page 7 )
Check your cable connections.
Call your router manufacturer.
I installed the Network
viewer program and entered
the WAN IP address I still
can’t see my cameras
•
•
•
• Check if your computer is using a Firewall application like
Norton Firewall.
• Check if you configured the correct port to receive the data
from your remote location.
• If your network device support web browser, try using the IP
address and port ( if needed) to see the cameras. If you can
watch the cameras on your Internet browser, the problem
could relate to an Internal firewall application.
• Check if your password is correct.
• Check if your wan IP address is correct
Digimerge Technologies Inc.
300Alden Road • Markham • Ontario • Canada • L3R4C1
tel: (905)946-8477 • fax: (905)947-0138
39

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement