Product Data Sheet
September 2014
00813-0100-4001, Rev SA
Rosemount 3051 Pressure Transmitter
With the Rosemount 3051 Pressure Transmitter, you’ll gain more control over your plant. You’ll be able to
reduce product variation and complexity as well as your total cost of ownership by leveraging one device
across a number of pressure, level and flow applications. You’ll have access to information you can use to
diagnose, correct and even prevent issues. And with unparalleled reliability and experience, the Rosemount
3051 is the industry standard that will help you perform at higher levels of efficiency and safety so you can
remain globally competitive.
Rosemount 3051
September 2014
Setting the Standard for Pressure Measurement
Proven best-in-class performance,
reliability and safety

Over 7 million installed

Reference accuracy 0.04% of span

Installed total performance of 0.14% of span

10-year stability of 0.2% of URL

SIL2/3 certified (IEC 61508)
Maximize installation and application
flexibility with the coplanar platform

Improve reliability and performance with integrated DP
Flowmeters, DP Level solutions and integral manifolds

Easy installation with all solutions fully assembled,
leak-tested and calibrated

Meet your application needs with an unsurpassed offering
Advanced functionality
Power advisory diagnostics

Detect on-scale failures caused by electrical loop issues before they impact your process
operation

This capability is safety certified for your most critical applications
Local operator interface

Straightforward menus and built-in configuration buttons allow you commission the device in less
than a minute

Configure in hazardous-area locations without removing the transmitter cover using external
buttons
Contents
Rosemount 3051C Coplanar™ Pressure Transmitter . . . . . . 4
Rosemount 3051L Level Transmitter . . . . . . . . . . . . . . . . . . 38
Rosemount 3051T In-Line Pressure Transmitter . . . . . . . . . 11
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Rosemount 3051CF Flowmeter Selection Guide . . . . . . . . . 17
3051 Product Certifications . . . . . . . . . . . . . . . . . . . . . . . . 56
Rosemount 3051CFA Annubar Flowmeter . . . . . . . . . . . . . 18
Pipe I.D. Range Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Rosemount 3051CFC Compact Flowmeter . . . . . . . . . . . . . 26
Rosemount 3051 Dimensional Drawings . . . . . . . . . . . . . . 66
Rosemount 3051CFP Integral Orifice Flowmeter . . . . . . . . 32
Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
2
www.rosemount.com
September 2014
Rosemount 3051
Industry leading capabilities extended to IEC 62591
(WirelessHART®)

Cost effectively implement wireless on the industry's most proven platform

Optimize safety with the industry's only intrinsically safe power module

Eliminate wiring design and construction complexities to lower costs by 40-60%

Quickly deploy new pressure, level and flow measurements in 70% less time
Innovative, integrated DP Flowmeters

Fully assembled, configured, and leak tested for out-of-the-box installation

Reduce straight pipe requirements, lower permanent pressure loss and achieve accurate
measurement in small line sizes

Up to 1.65% volumetric flow accuracy at 8:1 turndown
Proven, reliable, and innovative DP Level Technologies

Connect to virtually any process with a comprehensive offering of process connections, fill
fluids, direct mount or capillary connections and materials

Quantify and optimize total system performance with QZ option

Operate at higher temperature and in vacuum applications

Optimize level measurement with cost efficient Rosemount Tuned-System™ Assemblies
Instrument manifolds – quality, convenient, and easy
www.rosemount.com

Designed and engineered for optimal performance with Rosemount transmitters

Save installation time and money with factory assembly

Offers a variety of styles, materials and configurations
3
Rosemount 3051
September 2014
Rosemount 3051C Coplanar™ Pressure Transmitter
Rosemount 3051C Coplanar Pressure Transmitters are the industry standard for Differential,
Gage, and Absolute pressure measurement. The Coplanar Platform enables seamless
integration with manifolds, flow and level solutions. Capabilities include:
3051C Coplanar
Pressure Transmitter

Power Advisory can proactively detect degraded electrical loop integrity issues (Option Code
DA0)

Local Operator Interface with straightforward menus and built-in configuration buttons
(Option Code M4)

Safety Certification (Option Code QT)
See Specifications and options for more details on each configuration. Specification and selection of product materials, options, or
components must be made by the purchaser of the equipment. See page 54 for more information on Material Selection.
Additional information:
Specifications: page 45
Certifications: page 56
Dimensional Drawings: page 66
Table 1. 3051C Coplanar Pressure Transmitters Ordering Information
H The Standard offering represents the most common options. The starred options (H) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Model
Transmitter type
3051C(1)
Coplanar Pressure Transmitter
Measurement type
D
Differential
H
G
Gage
H
A(2)
Absolute
Pressure range
Differential (3051CD)
Gage (3051CG)
Absolute (3051CA)
1
–25 to 25 inH2O
(-62,16 to 62,16 mbar)
–25 to 25 inH2O
(-62,16 to 62,16 mbar)
0 to 30 psia
(0 to 2,06 bar)
H
2
–250 to 250 inH2O
(-621,60 to 621,60 mbar)
–250 to 250 inH2O
(-621,60 to 621,60 mbar)
0 to 150 psia
(0 to 10,34 bar)
H
3
–1000 to 1000 inH2O
(-2,48 to 2,48 bar)
–393 to 1000 inH2O
(-0,97 to 2,48 bar)
0 to 800 psia
(0 to 55,15 bar)
H
4
–300 to 300 psi
(-20,68 to 20,68 bar)
–14.2 to 300 psi
(-0,97 to 20,68 bar)
0 to 4000 psia
(0 to 275,79 bar)
H
5
–2000 to 2000 psi
(-137,89 to 137,89 bar)
–14.2 to 2000 psi
(-0,97 to 137,89 bar)
N/A
H
–3 to 3 inH2O
(-7,46 to 7,46 mbar)
N/A
N/A
0(3)
Transmitter output
A(4)
4–20 mA with Digital Signal Based on HART Protocol
H
F
FOUNDATION™ fieldbus Protocol
H
W(5)
PROFIBUS® PA Protocol
H
Wireless (requires wireless options and engineered polymer housing)
H
X
(6)
M(7)
4
Low-Power, 1-5 Vdc with Digital Signal Based on HART® Protocol
www.rosemount.com
September 2014
Rosemount 3051
Table 1. 3051C Coplanar Pressure Transmitters Ordering Information
H The Standard offering represents the most common options. The starred options (H) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Materials of construction
Process flange type
Flange material
Drain/vent
2
Coplanar
SST
SST
H
3(8)
Coplanar
Cast C-276
Alloy C-276
H
4
Coplanar
Alloy 400
Alloy 400/K-500
H
5
Coplanar
Plated CS
SST
H
7(8)
Coplanar
SST
Alloy C-276
H
8(8)
Coplanar
Plated CS
Alloy C-276
H
0
H
Alternate Process Connection
Isolating diaphragm
2(8)
316L SST
H
3(8)
Alloy C-276
H
4(9)
Alloy 400
5(9)
Tantalum (available on 3051CD and CG, Ranges 2–5 only; not available on 3051CA)
6(9)
Gold-plated Alloy 400 (use in combination with O-ring Option Code B)
7(9)
Gold-plated 316 SST
O-ring
A
Glass-filled PTFE
H
B
Graphite-filled PTFE
H
Sensor fill fluid
1
Silicone
H
2(9)
Inert (Differential and Gage only)
H
Housing material
Conduit entry size
A
Aluminum
½–14 NPT
H
B
Aluminum
M20 × 1.5
H
J
SST
½–14 NPT
H
K
SST
M20 × 1.5
H
P(10)
Engineered Polymer
No Conduit Entries
H
D(11)
Aluminum
G½
M(11)
SST
G½
Wireless options (requires Wireless Output Code X and Engineered Polymer Housing Code P)
Wireless transmit rate, operating frequency, and protocol
WA3
User Configurable Transmit Rate, 2.4GHz WirelessHART
Antenna and SmartPower
WP5
H
™
Internal Antenna, Compatible with Green Power Module (I.S. Power Module Sold Separately)
H
HART Revision configuration (requires HART Protocol Output Code A)
HR5(4)
Configured for HART Revision 5
H
HR7(4)
Configured for HART Revision 7
H
www.rosemount.com
5
Rosemount 3051
September 2014
Table 1. 3051C Coplanar Pressure Transmitters Ordering Information
H The Standard offering represents the most common options. The starred options (H) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Options (include with selected model number)
Extended product warranty
WR3
3-year limited warranty
H
WR5
5-year limited warranty
H
PlantWeb® control functionality
A01(12)
FOUNDATION fieldbus Control Function Block Suite
H
PlantWeb diagnostic functionality
DA0(13)
Power Advisory HART Diagnostic
H
D01(12)
FOUNDATION fieldbus Diagnostics Suite
H
Alternate flange
(14)
H2
Traditional Flange, 316 SST, SST drain/vent
H
H3(8)
Traditional Flange, Alloy C, Alloy C-276 drain/vent
H
H4
Traditional Flange, Cast Alloy 400, Alloy 400/K-500 drain/vent
H
H7(8)
Traditional Flange, 316 SST, Alloy C-276 drain/vent
H
HJ
DIN-Compliant Traditional Flange,SST,7/16 in. Adapter/Manifold Bolting
H
FA
Level Flange, SST, 2 in., ANSI Class 150, Vertical Mount 316 SST drain/vent
H
FB
Level Flange, SST, 2 in., ANSI Class 300, Vertical Mount 316 SST drain/vent
H
FC
Level Flange, SST, 3 in., ANSI Class 150, Vertical Mount 316 SST drain/vent
H
FD
Level Flange, SST, 3 in., ANSI Class 300, Vertical Mount 316 SST drain/vent
H
FP
DIN Level Flange, SST, DN 50, PN 40, Vertical Mount 316 SST drain/vent
H
FQ
DIN Level Flange, SST, DN 80, PN 40, Vertical Mount 316 SST drain/vent
H
HK(15)
DIN Compliant Traditional Flange, SST, 10 mm Adapter/Manifold Bolting 316 SST
HL
DIN Compliant Traditional Flange, SST, 12mm Adapter/Manifold Bolting 316 SST
Manifold assembly(16)
S5
Assemble to Rosemount 305 Integral Manifold
H
S6
Assemble to Rosemount 304 Manifold or Connection System
H
Integral mount primary element(15)(16)
S3
(17)
S4
Assemble to Rosemount 405 Compact Orifice Plate
®
Assemble to Rosemount Annubar or Rosemount 1195 Integral Orifice
H
H
(16)
Seal assemblies
S1(18)
Assemble to one Rosemount 1199 seal
H
S2(19)
Assemble to two Rosemount 1199 seals
H
Mounting bracket(20)
B4
Coplanar flange bracket, all SST, 2-in. pipe and panel
H
B1
Traditional flange bracket, CS, 2-in. pipe
H
B2
Traditional flange bracket, CS, panel
H
B3
Traditional flange flat bracket, CS, 2-in. pipe
H
B7
Traditional flange bracket, B1 with SST bolts
H
B8
Traditional flange bracket, B2 with SST bolts
H
B9
Traditional flange bracket, B3 with SST bolts
H
BA
Traditional flange bracket, B1, all SST
H
BC
Traditional flange bracket, B3, all SST
H
6
www.rosemount.com
September 2014
Rosemount 3051
Table 1. 3051C Coplanar Pressure Transmitters Ordering Information
H The Standard offering represents the most common options. The starred options (H) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Product certifications
E8
(21)
ATEX Flameproof and Dust Certification
H
ATEX Intrinsic Safety and Dust
H
IA
ATEX FISCO Intrinsic Safety; for FOUNDATION fieldbus or PROFIBUS PA protocol only
H
N1
ATEX Type n Certification and Dust
H
K8
ATEX Flameproof, Intrinsic Safety, Type n, Dust (combination of E8, I1 and N1)
H
E4(22)
TIIS Flame-proof
H
E5
FM Explosion-proof, Dust Ignition-Proof
H
I1
(23)
FM Intrinsically Safe, Nonincendive
H
IE
FM FISCO Intrinsically Safe; for FOUNDATION fieldbus or PROFIBUS PA protocol only
H
K5
FM Explosion-proof, Dust Ignition-Proof, Intrinsically Safe, and Division 2
H
C6
CSA Explosion-proof, Dust Ignition-proof, Intrinsically Safe, and Division 2
H
I6(10)
CSA Intrinsic Safety
H
K6
CSA and ATEX Explosion-proof, Intrinsically Safe, and Division 2 (combination of C6, E8, and I1)
H
E7
IECEx Flameproof, Dust Ignition-proof
H
I7
IECEx Intrinsic Safety
H
N7
IECEx Type n Certification
H
K7
IECEx Flame-proof, Dust Ignition-proof, Intrinsic Safety, and Type n (combination of I7, N7, and E7)
H
E2
INMETRO Flameproof
H
I2
INMETRO Intrinsic Safety
H
IB
INMETRO FISCO intrinsically safe; for FOUNDATION fieldbus or PROFIBUS PA protocols only
H
K2
INMETRO Flameproof, Intrinsic Safety
H
E3
China Flameproof
H
I3
China Intrinsic Safety
H
N3
China Type n
H
EM
Technical Regulations Customs Union (EAC) Flameproof
H
IM
Technical Regulations Customs Union (EAC) Intrinsic Safety
H
KM
Technical Regulations Customs Union (EAC) Flameproof and Intrinsic Safety
H
KB
FM and CSA Explosion-proof, Dust Ignition Proof, Intrinsically Safe, and Division 2 (combination of K5 and C6)
H
KD
FM, CSA, and ATEX Explosion-proof, Intrinsically Safe (combination of K5, C6, I1, and E8)
H
I5
Drinking water approval
DW(24)
NSF drinking water approval
H
Shipboard approvals
SBS(9)
American Bureau of Shipping
H
SBV(9)(25)
Bureau Veritas (BV)
H
SDN(9)
Det Norske Veritas
H
SLL(9)(25)
Lloyds Register (LR)
H
Custody transfer
C5(13)
Measurement Canada Accuracy Approval (limited availability depending on transmitter type and range;
contact an Emerson Process Management representative)
www.rosemount.com
H
7
Rosemount 3051
September 2014
Table 1. 3051C Coplanar Pressure Transmitters Ordering Information
H The Standard offering represents the most common options. The starred options (H) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Bolting material
L4
Austenitic 316 SST Bolts
H
L5
ASTM A 193, Grade B7M Bolts
H
L6
Alloy K-500 Bolts
H
Display and interface options
M4(26)
LCD Display with Local Operator Interface
H
M5
LCD Display
H
Calibration certificate
Q4
Calibration Certificate
H
QG(27)
Calibration Certificate and GOST Verification Certificate
H
QP
Calibration certification and tamper evident seal
H
Material traceability certification
Q8
H
Material Traceability Certification per EN 10204 3.1
Quality certification for safety
QS(13)
Prior-use certificate of FMEDA data
H
QT(13)
Safety certified to IEC 61508 with certificate of FMEDA
H
Configuration buttons
D4(13)
Analog Zero and Span
H
DZ(28)
Digital Zero Trim
H
Transient protection
T1(9)(29)
H
Transient Protection Terminal Block
Software configuration
C1(28)
Custom Software Configuration (completed CDS 00806-0100-4007 for wired and 00806-0100-4100 for
Wireless required with order)
H
Low power output
C2
0.8-3.2 Vdc Output with Digital Signal Based on HART Protocol (available with Output code M only)
H
Gage pressure calibration
Gage Calibration (Model 3051CA4 only)
H
C4(13)
Analog Output Levels Compliant with NAMUR Recommendation NE 43, Alarm High
H
CN(13)
Analog Output Levels Compliant with NAMUR Recommendation NE 43, Alarm Low
H
CR(13)
Custom alarm and saturation signal levels, high alarm (requires C1 and Configuration Data Sheet)
H
CS(13)
Custom alarm and saturation signal levels, low alarm (requires C1 and Configuration Data Sheet)
H
CT(13)
Rosemount standard low alarm
H
C3
Alarm levels
Pressure testing
P1
8
Hydrostatic Testing with Certificate
www.rosemount.com
September 2014
Rosemount 3051
Table 1. 3051C Coplanar Pressure Transmitters Ordering Information
H The Standard offering represents the most common options. The starred options (H) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Cleaning process area
P2
Cleaning for Special Service
P3
Cleaning for <1 PPM Chlorine/Fluorine
Flange adapters
DF(30)
1
/2 -14 NPT flange adapter(s)
H
Vent/drain valves
D7
Coplanar Flange Without Drain/Vent Ports
Conduit plug
DO(9)(31)
1
316 SST Conduit Plug
H
1
RC /4 RC /2 process connection
D9(32)
RC ¼ Flange with RC ½ Flange Adapter - SST
Max static line pressure
P9
4500 psig (310,26 bar) Static Pressure Limit (3051CD Ranges 2–5 only)
H
External Ground Screw Assembly
H
Surface finish certification for sanitary remote seals
H
Ground screw
V5(9)(33)
Surface finish
Q16
Toolkit total system performance reports
QZ
Remote Seal System Performance Calculation Report
H
Conduit electrical connector
GE(9)
M12, 4-pin, Male Connector (eurofast®)
H
GM(9)
A size Mini, 4-pin, Male Connector (minifast®)
H
NACE certificate
Q15(34)
Certificate of Compliance to NACE MR0175/ISO 15156 for wetted materials
H
Q25(34)
Certificate of Compliance to NACE MR0103 for wetted materials
H
Typical model number: 3051CD 2 A 2 2 A 1 A B4
(1) Select Configuration Buttons (option code D4 or DZ) or Local Operator Interface (option code M4) if local configuration buttons are required.
(2) If ordered with Wireless output code X, only Range 1-4, 316L SST diaphragm material (code 2), silicone fill fluid (code 1) and wireless housing (code P) are
available.
(3) 3051CD0 is only available with output code A and X. For output code A, only process flange code 0 (Alternate flange H2, H7, HJ or HK), isolating diaphragm code
2, O ring code A and bolting option L4 are available. For output code X, only process flange code 0 (Alternate flange H2), isolating diaphragm code 2, O ring code
A and bolting option L4 are available.
(4) Option HR5 configures the HART output to HART Revision 5. Option HR7 configures the HART output to HART Revision 7. The device can be field configured to
HART Revision 5 or 7 if desired. HART Revision 5 is the default HART output.
(5) For local addressing and configuration, M4 (Local Operator Interface) is required.
(6) Available approvals are FM Intrinsically Safe, (Option Code I5), CSA Intrinsically Safe (Option Code I6), ATEX Intrinsic Safety (Option Code I1), IECEx Intrinsic Safety
(Option Code I7) and EAC Intrinsic Safety (option code IM).
(7) Only available with C6, E2, E5, I5, K5, KB and E8 product certifications. Not available with GE, GM, SBS, DA0, M4, D4, DZ, QT, HR5, HR7, CR, CS, CT.
www.rosemount.com
9
Rosemount 3051
September 2014
(8) Materials of Construction comply with recommendations per NACE MR0175/ISO 15156 for sour oil field production environments. Environmental limits apply to
certain materials. Consult latest standard for details. Selected materials also conform to NACE MR0103 for sour refining environments.
(9) Not available with Wireless Output (code X).
(10) Only available with Wireless Output (code X).
(11) Not available with Product certifications options E8, K8, E5, K5, C6, K6, E7, K7, E2, K2, E3, KB, KD.
(12) Only valid with FOUNDATION fieldbus Output Code F.
(13) Only available with HART 4-20 mA Output (code A).
(14) Requires 0 code in Materials of Construction for Alternate Process Connection.
(15) Not valid with Option Code P9 for 4500 psi Static Pressure.
(16) “Assemble-to” items are specified separately and require a completed model number.
(17) Process flange limited to Coplanar (Option Codes 2, 3, 5, 7, 8) or Traditional (Option Codes H2, H3, H7).
(18) Not valid with Option Code D9 for RC1/2 Adapters.
(19) Not valid for Option Codes DF and D9 for Adapters.
(20) Panel mounting bolts are not supplied.
(21) Dust approval not applicable to Output Code X. See “IEC 62591 (WirelessHART Protocol)” on page 62 for wireless approvals.
(22) Only available with output codes A - 4-20mA HART, F - FOUNDATION fieldbus, and W - PROFIBUS PA. Also only available with G1/2 housing thread types.
(23) Nonincendive certification not provided with Wireless output option code (X).
(24) Not available with Alloy C-276 isolator (code 3), tantalum isolator (code 5), all cast C-276 flanges, all plated CS flanges, all DIN flanges, all Level flanges,
assemble-to manifolds (codes S5 and S6), assemble-to seals (codes S1 and S2), assemble-to primary elements (codes S3 and S4), surface finish certification (code
Q16), and remote seal system report (code QZ).
(25) Only available with product certifications E7, E8, I1, I7, IA, K7, K8, KD, N1, N7
(26) Not available with FOUNDATION fieldbus (Output Code F), Wireless (Output Code X), or Low Power Output (output code M).
(27) Contact an Emerson Process Management representative for availability.
(28) Only available with HART 4-20 mA Output (output code A) and Wireless Output (output code X)
(29) The T1 option is not needed with FISCO Product Certifications; transient protection is included in the FISCO product certification codes IA, IB, and IE.
(30) Not valid with Alternate Process Connection options S3, S4, S5, and S6.
(31) Transmitter is shipped with a 316 SST Conduit plug (uninstalled) in place of standard carbon steel conduit plug.
(32) Not available with Alternate Process Connection; DIN Flanges and Level Flanges.
(33) The V5 option is not needed with the T1 option; external ground screw assembly is included with the T1 option.
(34) NACE compliant wetted materials are identified by Footnote 8.
10
www.rosemount.com
September 2014
Rosemount 3051
Rosemount 3051T In-Line Pressure Transmitter
Rosemount 3051T In-Line Pressure Transmitters are the industry standard for Gage and
Absolute pressure measurement. The in-line, compact design allows the transmitter to
be connected directly to a process for quick, easy and cost effective installation.
Capabilities include:

Power Advisory can proactively detect degraded electrical loop integrity issues
(Option Code DA0)

Local Operator Interface with straightforward menus and built-in configuration
buttons (Option Code M4)

Safety Certification (Option Code QT)
3051T In-Line
Pressure Transmitter
See “Specifications” on page 45 and options for more details on each configuration. Specification and selection of product materials,
options, or components must be made by the purchaser of the equipment. See page 54 for more information on Material Selection.
Additional information:
Specifications: page 45
Certifications: page 56
Dimensional Drawings: page 66
Table 2. 3051T In-Line Pressure Transmitter Ordering Information
H The Standard offering represents the most common options. The starred options (H) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Model
Transmitter type
3051T(1)
In-Line Pressure Transmitter
Pressure type
G
A(2)
H
H
Gage
Absolute
Pressure range
1
2
3
4
5
Gage (3051TG)(3)
Absolute (3051TA)
-14.7 to 30 psi (-1,01 to 2,06 bar)
-14.7 to 150 psi (-1,01 to 10,34 bar)
-14.7 to 800 psi (-1,01 to 55,15 bar)
-14.7 to 4000 psi (-1,01 to 275,79 bar)
-14.7 to 10000 psi (-1,01 to 689,47 bar)
0 to 30 psia (0 to 2,06 bar)
0 to 150 psia (0 to 10,34 bar)
0 to 800 psia (0 to 55,15 bar)
0 to 4000 psia (0 to 275,79 bar)
0 to 10000 psia (0 to 689,47 bar)
H
H
H
H
H
Transmitter output
A(4)
F
W(5)
X(6)
M(7)
4–20 mA with Digital Signal Based on HART Protocol
FOUNDATION fieldbus Protocol
PROFIBUS PA Protocol
Wireless (requires wireless options and engineered polymer housing)
Low-Power 1-5 Vdc with Digital Signal Based on HART Protocol
H
H
H
H
Process connection style
2B
2C(8)
2F(9)
61(9)
1
/2–14 NPT Female
G½ A DIN 16288 Male (Range 1–4 only)
Coned and Threaded, Compatible with Autoclave Type F-250-C (Range 5 only)
Non-threaded Instrument flange (Range 1-4 only)
www.rosemount.com
H
H
11
Rosemount 3051
September 2014
Table 2. 3051T In-Line Pressure Transmitter Ordering Information
H The Standard offering represents the most common options. The starred options (H) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Isolating diaphragm
Process connection wetted parts material
2(10)
316L SST
Alloy C-276
3(10)
316L SST
Alloy C-276
H
H
Sensor fill fluid
1
2(9)
H
H
Silicone
Inert
Housing material
Conduit entry size
A
B
J
K
P(11)
D(12)
M(12)
½–14 NPT
M20 × 1.5
½–14 NPT
M20 × 1.5
No conduit entries
G½
G½
Aluminum
Aluminum
SST
SST
Engineered polymer
Aluminum
SST
H
H
H
H
H
Wireless options (requires wireless Output Code X and Engineered Polymer Housing Code P)
Wireless transmit rate, operating frequency, and protocol
WA3
H
User Configurable Transmit Rate, 2.4GHz WirelessHART
Antenna and SmartPower
WP5
Internal Antenna, Compatible with Green Power Module (I.S. Power Module Sold Separately)
H
HART Revision configuration (requires HART Protocol Output Code A)
HR5(4)
HR7(4)
Configured for HART Revision 5
Configured for HART Revision 7
H
H
Options (include with selected model number)
Extended product warranty
WR3
WR5
3-year limited warranty
5-year limited warranty
H
H
PlantWeb control functionality
A01(13)
FOUNDATION fieldbus Control Function Block Suite
H
PlantWeb diagnostic functionality
DA0(22)
D01(13)
Power Advisory HART Diagnostic
FOUNDATION fieldbus Diagnostics Suite
H
H
Integral assembly
S5(14)
Assemble to Rosemount 306 Integral Manifold
H
Diaphragm seal assemblies
S1(14)
Assemble to one Rosemount 1199 seal
H
Mounting bracket(15)
B4
Bracket for 2-in. Pipe or Panel Mounting, All SST
H
Product certifications
E8
I1(16)
12
ATEX Flameproof and Dust Certification
ATEX Intrinsic Safety and Dust
H
H
www.rosemount.com
September 2014
Rosemount 3051
Table 2. 3051T In-Line Pressure Transmitter Ordering Information
H The Standard offering represents the most common options. The starred options (H) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
IA
N1
K8
E4(17)
E5
I5(18)
IE
K5
C6
I6(11)
K6
E7
I7
N7
K7
E2
I2
IB
K2
E3
I3
N3
EM
IM
KM
KB
KD
ATEX Intrinsic Safety for FISCO; for FOUNDATION fieldbus or PROFIBUS PA protocols only
ATEX Type n Certification and Dust
ATEX Flame-proof, Intrinsic Safety, Type n, Dust (combination of E8, I1 and N1)
TIIS Flameproof
FM Explosion-proof, Dust Ignition-proof
FM Intrinsically Safe, Nonincendive
FM FISCO Intrinsically Safe; for FOUNDATION fieldbus or PROFIBUS PA protocols only
FM Explosion-proof, Dust Ignition-proof, Intrinsically Safe, and Division 2
CSA Explosion-proof, Dust Ignition-proof, Intrinsically Safe, and Division 2
CSA Intrinsic Safety
CSA and ATEX Explosion-proof, Intrinsically Safe, and Division 2 (combination of C6, E8, and I1)
IECEx Flameproof, Dust Ignition-proof
IECEx Intrinsic Safety
IECEx Type n Certification
IECEx Flameproof, Dust Ignition-proof, Intrinsic Safety, and Type n (combination of I7, N7, and E7)
INMETRO Flameproof
INMETRO Intrinsic Safety
INMETRO FISCO intrinsically safe; for FOUNDATION fieldbus or PROFIBUS PA protocols only
INMETRO Flameproof, Intrinsic Safety
China Flameproof
China Intrinsic Safety
China Type n
Technical Regulations Customs Union (EAC) Flameproof
Technical Regulations Customs Union (EAC) Intrinsic Safety
Technical Regulations Customs Union (EAC) Flameproof and Intrinsic Safety
FM and CSA Explosion-proof, Dust Ignition-proof, Intrinsically Safe, and Division 2 (combination of K5 and C6)
FM, CSA, and ATEX Explosion-proof, Intrinsically Safe (combination of K5, C6, I1, and E8)
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
Drinking water approval
DW(19)
NSF drinking water approval
H
Shipboard approvals
SBS(9)
SBV(9)(20)
SDN(9)
SLL(9)(20)
American Bureau of Shipping
Bureau Veritas (BV)
Det Norske Veritas
Lloyds Register (LR)
H
H
H
H
Custody transfer
C5
Measurement Canada Accuracy Approval (Limited availability depending on transmitter type and range. Contact
an Emerson Process Management representative)
H
Calibration certification
Q4
QG(21)
QP
Calibration Certificate
Calibration Certificate and GOST Verification Certificate
Calibration Certification and tamper evident seal
H
H
H
Material traceability certification
Q8
Material Traceability Certification per EN 10204 3.1
H
Quality certification for safety
QS(22)
QT(22)
Prior-use certificate of FMEDA Data
Safety certified to IEC 61508 with certificate of FMEDA
www.rosemount.com
H
H
13
Rosemount 3051
September 2014
Table 2. 3051T In-Line Pressure Transmitter Ordering Information
H The Standard offering represents the most common options. The starred options (H) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Configuration buttons
D4(22)
DZ(23)
H
H
Analog Zero and Span
Digital Zero Trim
Display and interface options
M4(24)
M5
H
H
LCD Display with Local Operator Interface
LCD Display
Wireless SST sensor module
WSM(11)
Wireless SST Sensor Module
H
316 SST Conduit Plug
H
Conduit plug
DO(9)(25)
Transient terminal block
T1(9)(26)
H
Transient Protection Terminal Block
Software configuration
C1(23)
Custom Software Configuration (Completed CDS 00806-0100-4007 for wired and 00806-0100-4100 for
wireless required with order)
H
Low power output
C2
0.8-3.2 Vdc Output with Digital Signal Based on HART Protocol (Available with Output code M only)
Alarm levels
C4(22)
CN(22)
CR(22)
CS(22)
CT(22)
Analog Output Levels Compliant with NAMUR Recommendation NE 43, Alarm High
Analog Output Levels Compliant with NAMUR Recommendation NE 43, Low Alarm
Custom alarm and saturation signal levels, high alarm (requires C1 and Configuration Data Sheet)
Custom alarm and saturation signal levels, low alarm (requires C1 and Configuration Data Sheet)
Rosemount standard low alarm
H
H
H
H
H
Pressure testing
P1
Hydrostatic Testing with Certificate
Cleaning process area(27)
P2
P3
Cleaning for Special Service
Cleaning for <1 PPM Chlorine/Fluorine
Ground screw
V5(9)(28)
External Ground Screw Assembly
H
Surface finish
Q16
Surface finish certification for sanitary remote seals
H
Toolkit total system performance reports
QZ
Remote Seal System Performance Calculation Report
H
Conduit electrical connector
GE(9)
GM(9)
14
M12, 4-pin, Male Connector (eurofast)
A size Mini, 4-pin, Male Connector (minifast)
H
H
www.rosemount.com
September 2014
Rosemount 3051
Table 2. 3051T In-Line Pressure Transmitter Ordering Information
H The Standard offering represents the most common options. The starred options (H) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
NACE certificate
Q15(29)
Q25(29)
Certificate of Compliance to NACE MR0175/ISO15156 for wetted materials
Certificate of Compliance to NACE MR0103 for wetted materials
H
H
Typical model number: 3051T G 5 F 2A 2 1 A B4
(1) Select Configuration Buttons (option code D4 or DZ) or Local Operator Interface (option code M4) if local configuration buttons are required.
(2) Wireless Output (code X) only available in absolute measurement type (code A) in range 1-5 with 1/2 14 NPT process connection (code 2B), and polymer housing
(code P).
(3) 3051TG lower range limit varies with atmospheric pressure.
(4) Option HR5 configures the HART output to HART Revision 5. Option HR7 configures the HART output to HART Revision 7. The device can be field configured to
HART Revision 5 or 7 if desired. HART Revision 5 is the default HART output.
(5) For local addressing and configuration, M4 (Local Operator Interface) is required.
(6) Requires wireless options and engineered polymer housing. Available approvals are FM Intrinsically Safe, (Option Code I5), CSA Intrinsically Safe (Option Code I6),
ATEX Intrinsic Safety (Option Code I1), IECEx Intrinsic Safety (Option Code I7), and EAC Intrinsic Safety (Option Code IM).
(7) Only available with C6, E2, E5, I5, K5, KB and E8 product certifications. Not available with GE, GM, SBS, DA0, M4, D4, DZ, QT, HR5, HR7, CR, CS, CT.
(8) Wireless Output (code X) only available in G1/2 A DIN 16288 Male process connection (code 2C) with range 1-4, 316 SST isolating Diaphragm (code 2), Silicone
Fill Fluid (code 1) and Housing Code (code P).
(9) Not available with Wireless Output (output code X).
(10) Materials of Construction comply with recommendations per NACE MR0175/ISO 15156 for sour oil field production environments. Environmental limits apply to
certain materials. Consult latest standard for details. Selected materials also conform to NACE MR0103 for sour refining environments.
(11) Only available with Wireless Output (output code X).
(12) Not available with Product certifications options E8, K8, E5, K5, C6, K6, E7, K7, E2, K2, E3, KB, KD.
(13) Only valid with FOUNDATION fieldbus Output Code F.
(14) “Assemble-to” items are specified separately and require a completed model number.
(15) Panel mounting bolts are not supplied.
(16) Dust approval not applicable to output code X. See “IEC 62591 (WirelessHART Protocol)” on page 62 for wireless approvals.
(17) Only available with output codes A - 4-20mA HART, F - FOUNDATION fieldbus, and W - PROFIBUS PA. Also only available with G1/2 housing thread types.
(18) Nonincendive certification not provided with Wireless output option code (X).
(19) Not available with Alloy C-276 isolator (option code 3), Assemble-to manifolds (option code S5), assemble-to seals (option code S1), surface finish certification
(option code Q16), and remote seal system report (option code QZ).
(20) Only available with product certifications E7, E8, I1, I7, IA, K7, K8, KD, N1, N7.
(21) Contact an Emerson Process Management representative for availability.
(22) Only available with HART 4-20 mA output (output code A).
(23) Only available with HART 4-20 mA output (output code A) and Wireless output (output code X).
(24) Not available with FOUNDATION fieldbus (output code F) and Wireless output (output code X) or Low Power (output code M).
(25) Transmitter is shipped with 316 SST conduit plug (uninstalled) in place of standard carbon steel conduit plug.
www.rosemount.com
15
Rosemount 3051
September 2014
(26) The T1 option is not needed with FISCO Product Certifications; transient protection is included in the FISCO product certification codes IA, IB, and IE.
(27) Not valid with Alternate Process Connection S5.
(28) The V5 option is not needed with T1 option; external ground screw assembly is included with the T1 option.
(29) NACE compliant wetted materials are identified by Footnote 10.
16
www.rosemount.com
September 2014
Rosemount 3051
Rosemount 3051CF Flowmeter Selection Guide
Rosemount 3051CF Flowmeters combine the proven Rosemount 3051 Pressure Transmitter and the latest primary element
technologies. All flowmeters are fully assembled, calibrated, configured, and leak tested for out-of-the-box installation and are
available with wired or wireless capabilities to meet all of your application needs.
Rosemount 3051CFA Annubar Flowmeter
Rosemount Annubar technology minimizes permanent pressure loss
while delivering best in class accuracy.

Lowest material costs for large line sizes

Flo-tap enables installation without process shutdown

Realize up to 96% less permanent pressure loss compared to
traditional orifice plate installations
Rosemount 3051CFC Compact Conditioning Flowmeter
Rosemount Compact Conditioning technologies provide
unprecedented performance with minimal straight-run requirements.
Solutions include Conditioning Orifice Plate or Annubar primary
elements.

Conditioning Orifice requires only 2 pipe diameters up and
downstream

Eliminate swirl and regular profiles resulting in more stable and
accurate flow measurement

Savings up to 55% when compared to a traditional orifice plate
installation can be realized
Rosemount 3051CFP Integral Orifice Flowmeter
Rosemount Integral Orifice Flowmeters deliver highly accurate
small-bore flow measurement capability with minimal installation and
maintenance requirements.
www.rosemount.com

Best performance for small line sizes 1/2” (15 mm) to 11/2” (40 mm)

Precision honed pipe section and tight machining tolerances deliver
higher installed performance

Reduces uncertainty by up to 5% compared to traditional orifice plate
installation
17
Rosemount 3051
September 2014
Rosemount 3051CFA Annubar Flowmeter
The Rosemount 3051CFA Annubar Flowmeter utilizes the T-shaped sensor design that
delivers best in class accuracy and performance while meeting the needs of diverse
process applications, whether it is high accuracy for precision control or high strength
for severe flow applications. Main capabilities include:

Up to 1.8% of flow rate accuracy

Available in 2 to 96-in. (50 - 2400 mm) line sizes

Fully assembled and leak tested for out-of-the-box installation

Power Advisory can proactively detect degraded electrical loop integrity issues
(Option Code DA0)

Local Operator Interface with straightforward menus and built-in configuration
buttons (Option Code M4)
See “Specifications” on page 45 and options for more details on each configuration. Specification and selection of product materials,
options, or components must be made by the purchaser of the equipment. See page 54 for more information on Material Selection.
Additional information:
Specifications: page 45
Certifications: page 56
Dimensional Drawings: page 66
Table 3. Rosemount 3051CFA Annubar Flowmeter Ordering Information
H The Standard offering represents the most common options. The starred options (H) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Model
Product description
3051CFA(1)
Annubar Flowmeter
Measurement type
Differential Pressure
H
L
Liquid
H
G
Gas
H
S
Steam
H
2-in. (50 mm)
H
D
Fluid type
Line size
020
1
025
2 /2-in. (63.5 mm)
H
030
3-in. (80 mm)
H
035
31/2-in. (89 mm)
H
040
4-in. (100 mm)
H
050
5-in. (125 mm)
H
060
6-in. (150 mm)
H
070
7-in. (175 mm)
H
080
8-in. (200 mm)
H
100
10-in. (250 mm)
H
120
12-in. (300 mm)
H
140
14-in. (350 mm)
18
www.rosemount.com
September 2014
Rosemount 3051
Table 3. Rosemount 3051CFA Annubar Flowmeter Ordering Information
H The Standard offering represents the most common options. The starred options (H) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
160
16-in. (400 mm)
180
18-in. (450 mm)
200
20-in. (500 mm)
240
24-in. (600 mm)
300
30-in. (750 mm)
360
36-in. (900 mm)
420
42-in. (1066 mm)
480
48-in. (1210 mm)
600
60-in. (1520 mm)
720
72-in. (1820 mm)
780
78-in (1950 mm)
840
84-in. (2100 mm)
900
90-in. (2250 mm)
960
96-in (2400 mm)
Pipe I.D. range
C
Range C from the Pipe I.D. Range Codes table
H
D
Range D from the Pipe I.D. Range Codes table
H
A
Range A from the Pipe I.D. Range Codes table
B
Range B from the Pipe I.D. Range Codes table
E
Range E from the Pipe I.D. Range Codes table
Z
Non-standard Pipe I.D. Range Codes or Line Sizes greater than 12 inches
Pipe material/mounting assembly material
C
Carbon steel (A105)
H
S
316 Stainless Steel
H
0
No Mounting (customer supplied)
H
G
Chrome-Moly Grade F-11
N
Chrome-Moly Grade F-22
J
Chrome-Moly Grade F-91
Piping orientation
H
Horizontal Piping
H
D
Vertical Piping with Downwards Flow
H
U
Vertical Piping with Upwards Flow
H
Annubar type
P
Pak-Lok
H
F
Flanged with opposite side support
H
L
Flange-Lok
G
Gear-Drive Flo-Tap
M
Manual Flo-Tap
Sensor material
S
316 Stainless Steel
H
Alloy C-276
www.rosemount.com
H
19
Rosemount 3051
September 2014
Table 3. Rosemount 3051CFA Annubar Flowmeter Ordering Information
H The Standard offering represents the most common options. The starred options (H) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Sensor size
1
Sensor size 1 — Line sizes 2-in. (50 mm) to 8-in. (200 mm)
H
2
Sensor size 2 — Line sizes 6-in. (150 mm) to 96-in. (2400 mm)
H
3
Sensor size 3 — Line sizes greater than 12-in. (300 mm)
H
Mounting type
T1
Compression or Threaded Connection
H
A1
150# RF ANSI
H
A3
300# RF ANSI
H
A6
600# RF ANSI
H
D1
DN PN16 Flange
H
D3
DN PN40 Flange
H
D6
DN PN100 Flange
H
A9(2)
900# RF ANSI
AF(2)
1500# RF ANSI
AT(2)
2500 # RF ANSI
R1
150# RTJ Flange
R3
300# RTJ Flange
R6
600# RTJ Flange
R9(2)
900# RTJ Flange
RF(2)
1500# RTJ Flange
RT(2)
2500# RTJ Flange
Opposite side support or packing gland
0
H
No opposite side support or packing gland (required for Pak-Lok and Flange-Lok models)
Opposite Side Support – Required for Flanged Models
C
NPT Threaded Opposite Support Assembly – Extended Tip
H
D
Welded Opposite Support Assembly – Extended Tip
H
Packing Gland – Required for Flo-Tap Models
Packing Gland Material
Rod Material
Packing Material
(3)
Stainless Steel Packing Gland/Cage Nipple
Carbon Steel
PTFE
K(3)
Stainless Steel Packing Gland/Cage Nipple
Stainless Steel
PTFE
L(3)
Stainless Steel Packing Gland/Cage Nipple
Carbon Steel
Graphite
N(3)
Stainless Steel Packing Gland/Cage Nipple
Stainless Steel
Graphite
R
Alloy C-276 Packing Gland/Cage Nipple
Stainless Steel
Graphite
J
Isolation valve for Flo-Tap models
0
Not Applicable or Customer Supplied
1
Gate Valve, Carbon Steel
2
Gate Valve, Stainless Steel
5
Ball Valve, Carbon Steel
6
Ball Valve, Stainless Steel
H
Temperature measurement
T
Integral RTD – not available with Flanged model greater than class 600#
H
0
No Temperature Sensor
H
R
Remote Thermowell and RTD
20
www.rosemount.com
September 2014
Rosemount 3051
Table 3. Rosemount 3051CFA Annubar Flowmeter Ordering Information
H The Standard offering represents the most common options. The starred options (H) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Transmitter connection platform
3
Direct-mount, Integral 3-valve Manifold– not available with Flanged model greater than class 600
H
5
Direct -mount, 5-valve Manifold – not available with Flanged model greater than class 600
H
1
H
7
Remote-mount NPT Connections ( /2-in. NPT)
6
Direct-mount, high temperature 5-valve Manifold – not available with Flanged model greater than class 600
8
Remote-mount SW Connections (1/2-in.)
Differential pressure range
1
0 to 25 in H2O (0 to 62,16 mbar)
H
2
0 to 250 in H2O (0 to 621,60 mbar)
H
3
0 to 1000 in H2O (0 to 2,48 bar)
H
Transmitter output
A(4)
4–20 mA with digital signal based on HART Protocol
H
F
FOUNDATION fieldbus Protocol
H
W(5)
PROFIBUS PA Protocol
H
X(6)
Wireless (Requires wireless options and engineered polymer housing)
H
M(7)
Low-Power 1-5 Vdc with Digital Signal Based on HART Protocol
Transmitter housing material
Conduit entry size
A
Aluminum
1
/2-14 NPT
H
B
Aluminum
M20 x 1.5
H
J
SST
1/2-14 NPT
H
K
SST
M20 x 1.5
H
P(8)
Engineered polymer
No conduit entries
H
D(9)
Aluminum
G1/2
M(9)
SST
G1/2
Transmitter performance class
1
1.8% flow rate accuracy, 8:1 flow turndown, 5-yr. stability
H
Wireless options (requires Wireless Output Code X and Engineered Polymer Housing Code P)
Wireless transmit rate, operating frequency, and protocol
WA3
User Configurable Transmit Rate, 2.4GHz WirelessHART
H
Antenna and SmartPower
WP5
Internal Antenna, Compatible with Green Power Module (I.S. Power Module Sold Separately)
H
HART Revision configuration (requires HART Protocol Output Code A)
HR5(4)
Configured for HART Revision 5
H
HR7(4)
Configured for HART Revision 7
H
Options (include with selected model number)
Extended product warranty
WR3
3-year limited warranty
H
WR5
5-year limited warranty
H
www.rosemount.com
21
Rosemount 3051
September 2014
Table 3. Rosemount 3051CFA Annubar Flowmeter Ordering Information
H The Standard offering represents the most common options. The starred options (H) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Pressure testing
P1(10)
Hydrostatic Testing with Certificate
PX(10)
Extended Hydrostatic Testing
Special cleaning
P2
Cleaning for Special Services
PA
Cleaning per ASTM G93 Level D (Section 11.4)
Material testing
V1
Dye Penetrant Exam
Material examination
V2
Radiographic Examination
Flow calibration
W1
Flow Calibration (Average K)
Special inspection
QC1
Visual & Dimensional Inspection with Certificate
H
QC7
Inspection & Performance Certificate
H
Surface finish
RL
Surface finish for Low Pipe Reynolds # in Gas & Steam
H
RH
Surface finish for High Pipe Reynolds # in Liquid
H
Material traceability certification
Q8(11)
Material Traceability Certification per EN 10474:2004 3.1
Code conformance
H
(12)
J2
ANSI/ASME B31.1
J3
ANSI/ASME B31.3
Materials conformance
J5(13)
NACE MR-0175 / ISO 15156
Country certification
J6
European Pressure Directive (PED)
J1
Canadian Registration
H
Installed in flanged pipe spool section
H3
150# Flanged Connection with Rosemount Standard Length and Schedule
H4
300# Flanged Connection with Rosemount Standard Length and Schedule
H5
600# Flanged Connection with Rosemount Standard Length and Schedule
Instrument connections for remote mount options
G2
Needle Valves, Stainless Steel
H
G6
OS&Y Gate Valve, Stainless Steel
H
G1
Needle Valves, Carbon Steel
G3
Needle Valves, Alloy C-276
G5
OS&Y Gate Valve, Carbon Steel
G7
OS&Y Gate Valve, Alloy C-276
22
www.rosemount.com
September 2014
Rosemount 3051
Table 3. Rosemount 3051CFA Annubar Flowmeter Ordering Information
H The Standard offering represents the most common options. The starred options (H) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Special shipment
Y1
Mounting Hardware Shipped Separately
H
Special dimensions
VM
Variable Mounting
VT
Variable Tip
VS
Variable length Spool Section
PlantWeb control functionality
A01(14)
FOUNDATION fieldbus Control Function Block Suite
H
PlantWeb diagnostic functionality
DA0(15)
Power Advisory HART Diagnostic
H
D01(14)
FOUNDATION fieldbus Diagnostics Suite
H
Product certifications
E8
ATEX Flameproof, Dust
H
I1(16)
ATEX Intrinsic Safety and Dust
H
IA
ATEX FISCO Intrinsic Safety; for FOUNDATION fieldbus or PROFIBUS PA protocols only
H
N1
ATEX Type n and Dust
H
K8
ATEX Flameproof, Intrinsic Safety, Type n, Dust (combination of E8, I1 and N1)
H
E5
FM Explosion-proof, Dust Ignition-proof
H
I5(17)
FM Intrinsically Safe, Nonincendive
H
IE
FM FISCO Intrinsically Safe; for FOUNDATION fieldbus or PROFIBUS PA protocols only
H
K5
FM Explosion-proof, Dust Ignition-proof, Intrinsically Safe, and Division 2 (combination of E5 and I5)
H
C6
CSA Explosion-proof, Dust Ignition-proof, Intrinsically Safe, and Division 2
H
I6 (8)
CSA Intrinsically Safe
H
K6
CSA and ATEX Explosion-proof, Intrinsically Safe, and Division 2 (combination of C6, E8, and I1)
H
E7
IECEx Flameproof, Dust Ignition-proof
H
I7
IECEx Intrinsic Safety
H
N7
IECEx Type n
H
K7
IECEx Flameproof, Dust Ignition-proof, Intrinsic Safety, and Type n (combination of I7, N7 and E7)
H
E2
INMETRO Flameproof
H
I2
INMETRO Intrinsic Safety
H
IB
INMETRO FISCO intrinsically safe; for FOUNDATION fieldbus or PROFIBUS PA protocols only
H
K2
INMETRO Flameproof, Intrinsic Safety
H
E3
China Flameproof
H
I3
China Intrinsic Safety
H
KB
FM and CSA Explosion-proof, Dust Ignition-proof, Intrinsically Safe, and Division 2 (combination of K5 and C6)
H
KD
CSA, FM, and ATEX Explosion-proof, Intrinsically Safe (combination of K5, C6, I1, and E8)
H
Sensor fill fluid and O-ring options
L1(18)
Inert Sensor Fill Fluid Note: Silicone fill fluid is standard.
H
L2
Graphite-Filled (PTFE) O-ring
H
LA(18)
Inert Sensor Fill Fluid and Graphite-Filled (PTFE) O-ring
H
www.rosemount.com
23
Rosemount 3051
September 2014
Table 3. Rosemount 3051CFA Annubar Flowmeter Ordering Information
H The Standard offering represents the most common options. The starred options (H) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Shipboard approvals
SBS(18)
American Bureau of Shipping
SLL(18)(19)
Lloyds Register (LR)
H
Display and interface options
M4(20)
LCD Display with Local Operator Interface
H
M5
LCD Display
H
Transmitter calibration certification
Q4
H
Calibration Certificate for Transmitter
Quality certification for safety
QS(15)
Prior-use certificate of FMEDA data
H
QT(15)
Safety certified to IEC 61508 with certificate of FMEDA
H
Transient protection
T1(18)(21)
H
Transient terminal block
Manifold for remote mount option
F2
3-Valve Manifold, Stainless Steel
H
F6
5-Valve Manifold, Stainless Steel
H
F1
3-Valve Manifold, Carbon Steel
F3
3-Valve Manifold, Alloy C-276
F5
5-Valve Manifold, Carbon Steel
F7
5-Valve Manifold, Alloy C-276
Lower power output
C2
0.8-3.2 Vdc Output with Digital Signal based on HART Protocol (Available with Output code M only)
Alarm levels
C4(15)
NAMUR Alarm and Saturation Levels, High Alarm
H
CN(15)
NAMUR Alarm and Saturation Levels, Low Alarm
H
CR(15)
Custom alarm and saturation signal levels, high alarm
H
CS(15)
Custom alarm and saturation signal levels, low alarm
H
CT(15)
Rosemount Standard low alarm
H
Configuration buttons
D4(15)
Analog Zero and Span
H
DZ(22)
Digital Zero Trim
H
Ground screw
V5(18)(23)
H
External Ground Screw Assembly
Typical model number:
3051CFA
D
L
060
D
C
H
P
S
2
T1
0
0
0
3
2
A
A
1
(1) Select Configuration Buttons (option code D4 or DZ) or Local Operator Interface (option code M4) if local configuration buttons are required.
(2) Available in remote mount applications only.
(3) The cage nipple is constructed of 304 SST.
24
www.rosemount.com
September 2014
Rosemount 3051
(4) Option HR5 configures the HART output to HART Revision 5. Option HR7 configures the HART output to HART Revision 7. The device can be field configured to
HART Revision 5 or 7 if desired. HART Revision 5 is the default HART output.
(5) For local addressing and configuration, M4 (Local Operator Interface) is required.
(6) Requires wireless options and engineered polymer housing. Available approvals are FM Intrinsically Safe, (option code I5), CSA Intrinsically Safe (option code I6),
ATEX Intrinsic Safety (option code I1), and IECEx Intrinsic Safety (option code I7).
(7) Only available with C6, E2, E5, I5, K5, KB and E8 approval. Not available with GE, GM, SBS, DA0, M4, D4, DZ, QT, HR5, HR7, CR, CS, CT.
(8) Only available with Wireless Output (output code X).
(9) Not available with Product certifications options E8, K8, E5, K5, C6, K6, E7, K7, E2, K2, E3, KB, KD.
(10) Applies to assembled flowmeter only, mounting not tested.
(11) Instrument Connections for Remote Mount Options and Isolation Valves for Flo-tap Models are not included in the Material Traceability Certification.
(12) Not available with Transmitter Connection Platform 6.
(13) Materials of Construction comply with metallurgical requirements within NACE MR0175/ISO for sour oil field production environments. Environmental limits
apply to certain materials. Consult latest standard for details. Selected materials also conform to NACE MR0103 for sour refining environments.
(14) Only valid with FOUNDATION fieldbus output (output code F).
(15) Only available with 4-20 mA HART Output (output Code A).
(16) Dust approval not applicable to output code X. See “IEC 62591 (WirelessHART Protocol)” on page 62 for wireless approvals
(17) Nonincendive certification not provided with Wireless output option code (X).
(18) Not available with Wireless Output (output code X).
(19) Only available with product certifications E7, E8, I1, I7, IA, K7, K8, KD, N1, N7
(20) Not available with FOUNDATION Fieldbus (Output Code F) or Wireless Output (output code X) or Low Power (output code M).
(21) The T1 option is not needed with FISCO Product Certifications, transient protection is included with the FISCO Product Certification codes IA, IB, and IE.
(22) Only available with 4-20 mA HART Output (output code A) and Wireless output (Output Code X).
(23) The V5 option is not needed with the T1 option; external ground screw assembly is included with the T1 option.
www.rosemount.com
25
Rosemount 3051
September 2014
Rosemount 3051CFC Compact Flowmeter
Rosemount 3051CFC Compact Flowmeters provide a quick, reliable installation
between existing raised face flanges. Depending on your application needs, you can
reduce energy loss with the Compact Annubar or minimize straight run requirements
with the Conditioning Orifice.

Up to 1.8% of flow rate accuracy

Available in 1/2 to 12-in. (15 - 300 mm) line sizes

Fully assembled and leak tested for out-of-the-box installation

Power Advisory can proactively detect degraded electrical loop integrity issues.
(Option Code DA0)

Local Operator Interface with straightforward menus and built-in configuration
buttons (Option Code M4)
See “Specifications” on page 45 and options for more details on each configuration. Specification and selection of product materials,
options, or components must be made by the purchaser of the equipment. See page 54 for more information on Material Selection.
Additional information:
Specifications: page 45
Certifications: page 56
Dimensional Drawings: page 66
Table 4. Rosemount 3051CFC Compact Flowmeter Ordering Information
H The Standard offering represents the most common options. The starred options (H) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Model
Product description
3051CFC(1)
Compact Flowmeter
Measurement type
D
Differential Pressure
H
Primary element technology
A
C
P
Annubar Averaging Pitot Tube
Conditioning Orifice Plate
Orifice Plate
H
H
H
Material type
S
316 SST
H
1/2-in. (15 mm)
H
H
H
H
H
H
H
H
H
H
Line size
005(2)
010(2)
015(2)
020
030
040
060
080
100(3)
120(3)
26
1-in. (25 mm)
11/2-in. (40 mm)
2-in. (50 mm)
3-in. (80 mm)
4-in. (100 mm)
6-in. (150 mm)
8-in. (200 mm)
10-in. (250 mm)
12-in. (300 mm)
www.rosemount.com
September 2014
Rosemount 3051
Table 4. Rosemount 3051CFC Compact Flowmeter Ordering Information
H The Standard offering represents the most common options. The starred options (H) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Primary element type
N000
N040
N050
N065(4)
H
H
Annubar Sensor Size 1
0.40 Beta Ratio
0.50 Beta Ratio
0.65 Beta Ratio
H
Temperature measurement
0
R
H
No Temperature Sensor
Remote Thermowell and RTD
Transmitter connection platform
3
7
H
H
Direct-mount
Remote-mount, NPT Connections
Differential pressure range
1
2
3
H
H
H
0 to 25 in H2O (0 to 62,16 mbar)
0 to 250 in H2O (0 to 621,60 mbar)
0 to 1000 in H2O (0 to 2,48 bar)
Transmitter output
A(5)
F
W(6)
X(7)
M(8)
4–20 mA with digital signal based on HART Protocol
FOUNDATION fieldbus Protocol
PROFIBUS PA Protocol
Wireless (Requires wireless options and engineered polymer housing)
Low-Power 1-5 Vdc with Digital Signal Based on HART Protocol
Transmitter housing material
Conduit entry size
A
B
J
K
P(9)
D(10)
M(10)
1
Aluminum
Aluminum
SST
SST
Engineered polymer
Aluminum
SST
/2-14 NPT
M20 x 1.5
1
/2-14 NPT
M20 x 1.5
No conduit entries
G1/2
G1/2
H
H
H
H
H
H
H
H
H
Transmitter performance class
1
Up to ±1.65% flow rate accuracy, 8:1 flow turndown, 5-year stability
H
Wireless options (requires Wireless Output Code X and Engineered Polymer Housing Code P)
Wireless transmit rate, operating frequency, and protocol
WA3
User Configurable Transmit Rate, 2.4GHz WirelessHART
H
Antenna and SmartPower
WP5
Internal Antenna, Compatible with Green Power Module (I.S. Power Module Sold Separately)
H
HART Revision Configuration (requires HART Protocol Output Code A)
HR5(5)
HR7(5)
Configured for HART Revision 5
Configured for HART Revision 7
H
H
Options (include with selected model number)
Extended product warranty
WR3
WR5
3-year limited warranty
5-year limited warranty
www.rosemount.com
H
H
27
Rosemount 3051
September 2014
Table 4. Rosemount 3051CFC Compact Flowmeter Ordering Information
H The Standard offering represents the most common options. The starred options (H) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Installation accessories
AB
AC
AD
DG
DH
DJ
JB
JR
JS
ANSI Alignment Ring (150#) (Only required for 10-in. (250 mm) and 12-in. (300mm) line sizes)
ANSI Alignment Ring (300#) (Only required for 10-in. (250 mm) and 12-in. (300mm) line sizes)
ANSI Alignment Ring (600#) (Only required for 10-in. (250 mm) and 12-in. (300mm) line sizes)
DIN Alignment Ring (PN16)
DIN Alignment Ring (PN40)
DIN Alignment Ring (PN100)
JIS Alignment Ring (10K)
JIS Alignment Ring (20K)
JIS Alignment Ring (40K)
H
H
H
H
H
H
Remote adapters
FE
H
Flange Adapters 316 SST (1/2-in NPT)
High temperature application
HT
Graphite Valve Packing (Tmax = 850 °F)
Flow calibration
WC(11)
WD(11)(12)
Flow Calibration, 3 pt, Conditioning Orifice Option C (all pipe schedules)
Flow Calibration, 10 pt, Conditioning Option C (All Schedules), Annubar Option A (Schedule 40)
Pressure testing
P1
Hydrostatic Testing with Certificate
Special cleaning
P2(13)
PA
Cleaning for Special Services
Cleaning per ASTM G93 Level D (Section 11.4)
Special inspection
QC1
QC7
Visual & Dimensional Inspection with Certificate
Inspection and Performance Certificate
H
H
Transmitter calibration certification
Q4
Calibration Certificate for Transmitter
H
Quality certification for safety
QS(14)
QT(14)
Prior-use certificate of FMEDA data
Safety certified to IEC 61508 with certificate of FMEDA
H
H
Material traceability certification
Q8
Material Traceability Certification per EN 10204:2004 3.1
H
Code conformance
J2
J3
J4
ANSI/ASME B31.1
ANSI/ASME B31.3
ANSI/ASME B31.8
Materials conformance
J5(15)
NACE MR-0175 / ISO 15156
Country certification
J1
Canadian Registration
Product certifications
E8
I1(16)
28
ATEX Flameproof, Dust
ATEX Intrinsic Safety and Dust
H
H
www.rosemount.com
September 2014
Rosemount 3051
Table 4. Rosemount 3051CFC Compact Flowmeter Ordering Information
H The Standard offering represents the most common options. The starred options (H) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
IA
N1
K8
E5
I5(17)
IE
K5
C6
I6(9)
K6
E7
I7
N7
K7
E2
I2
IB
K2
E3
I3
KB
KD
ATEX FISCO Intrinsic Safety; for FOUNDATION fieldbus or PROFIBUS PA protocols only
ATEX Type n and Dust
ATEX Flameproof, Intrinsic Safety, Type n, Dust (combination of E8, I1 and N1)
FM Explosion-proof, Dust Ignition-proof
FM Intrinsically Safe, Nonincendive
FM FISCO Intrinsically Safe; for FOUNDATION fieldbus or PROFIBUS PA protocols only
FM Explosion-proof, Dust Ignition-proof, Intrinsically Safe, and Division 2 (combination of E5 and I5)
CSA Explosion-proof, Dust Ignition-proof, Intrinsically Safe, and Division 2
CSA Intrinsically Safe
CSA and ATEX Explosion-proof, Intrinsically Safe, and Division 2 (combination of C6, E8, and I1)
IECEx Flameproof, Dust Ignition-proof
IECEx Intrinsic Safety
IECEx Type n
IECEx Flameproof, Dust Ignition-proof, Intrinsic Safety, and Type n (combination of I7, N7 and E7)
INMETRO Flameproof
INMETRO Intrinsic Safety
INMETRO FISCO intrinsically safe; for FOUNDATION fieldbus or PROFIBUS PA protocols only
INMETRO Flameproof, Intrinsic Safety
China Flameproof
China Intrinsic Safety
FM and CSA Explosion-proof, Dust Ignition-proof, Intrinsically Safe, and Division 2 (combination of K5 and C6)
CSA, FM, and ATEX Explosion-proof, Intrinsically Safe (combination of K5, C6, I1, and E8)
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
Sensor fill fluid and O-ring options
L1(18)
L2
LA(18)
Inert Sensor Fill Fluid
Graphite-Filled (PTFE) O-ring
Inert Sensor Fill Fluid and Graphite-Filled (PTFE) O-ring
H
H
H
Shipboard approvals
SBS(18)
SLL(18)(19)
American Bureau of Shipping
Lloyds Register (LR)
H
Display and interface options
M4(20)
M5
LCD Display with Local Operator Interface
LCD Display
H
H
Transient protection
T1(18)(21)
Transient terminal block
H
Manifold for remote mount option
F2
F6
3-Valve Manifold, Stainless Steel
5-Valve Manifold, Stainless Steel
H
H
PlantWeb control functionality
A01(22)
FOUNDATION fieldbus Control Function Block Suite
H
PlantWeb diagnostic functionality
DA0(14)
D01(22)
Power Advisory HART Diagnostic
FOUNDATION fieldbus Diagnostic Suite
H
H
Low power output
C2
0.8-3.2 Vdc Output with Digital Signal Based on HART Protocol (available with Output code M only)
www.rosemount.com
29
Rosemount 3051
September 2014
Table 4. Rosemount 3051CFC Compact Flowmeter Ordering Information
H The Standard offering represents the most common options. The starred options (H) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Alarm levels
C4(14)
CN(14)
CR(14)
CS(14)
CT(14)
H
H
H
H
H
NAMUR Alarm and Saturation Levels, High Alarm
NAMUR Alarm and Saturation Levels, Low Alarm
Custom alarm and saturation signal levels, high alarm
Custom alarm and saturation signal levels, low alarm
Rosemount Standard low alarm
Ground screw
V5(18)(23)
H
External Ground Screw Assembly
Configuration buttons
D4(14)
DZ(24)
H
H
Analog Zero and Span
Digital Zero Trim
Typical model number:
3051CFC D C S 060 N 065 0 3 2 A A 1 WC E5 M5
(1) Select Configuration Buttons (option code D4 or DZ) or Local Operator Interface (option code M4) if local configuration buttons are required.
(2) Available with Primary Element Technology P only.
(3) 10-in. (250 mm) and 12-in. (300 mm) line sizes not available with Primary Element Technology A.
(4) For 2-in. (50 mm) line sizes the Primary Element Type is 0.6 for Primary Element Technology Code C.
(5) Option HR5 configures the HART output to HART Revision 5. Option HR7 configures the HART output to HART Revision 7. The device can be field configured to
HART Revision 5 or 7 if desired. HART Revision 5 is the default HART output.
(6) For local addressing and configuration, M4 (Local Operator Interface) is required.
(7) Requires wireless options and engineered polymer housing. Available approvals are FM Intrinsically Safe, (option code I5), CSA Intrinsically Safe (option code I6),
ATEX Intrinsic Safety (option code I1), and IECEx Intrinsic Safety (option code I7).
(8) Only available with C6, E2, E5, I5, K5, KB and E8 approval. Not available with GE, GM, SBS, DA0, M4, D4, DZ, QT, HR5, HR7, CR, CS, CT.
(9) Only available with Wireless Output (output code X).
(10) Not available with Product certifications options E8, K8, E5, K5, C6, K6, E7, K7, E2, K2, E3, KB, KD.
(11) Available with Primary Element Technology C only.
(12) For Annubar option A, consult factory for pipe schedules other than schedule 40.
(13) Available with Primary Element Technology C or P only.
(14) Only available with HART 4-20 mA Output (output code A).
(15) Materials of Construction comply with metallurgical requirements within NACE MR0175/ISO for sour oil field production environments. Environmental limits
apply to certain materials. Consult latest standard for details. Selected materials also conform to NACE MR0103 for sour refining environments.
(16) Dust approval not applicable to output code X. See “IEC 62591 (WirelessHART Protocol)” on page 62 for wireless approvals
(17) Nonincendive certification not provided with Wireless output option code (X).
(18) Not available with Wireless output (output code X).
(19) Only available with product certifications E7, E8, I1, I7, IA, K7, K8, KD, N1, N7
(20) Not available with output code F - FOUNDATION fieldbus or Wireless output (output code X) or Low Power (output code M).
(21) The T1 option is not needed with FISCO Product Certifications, transient protection is included with the FISCO Product Certification code IA, IB, and IE.
30
www.rosemount.com
September 2014
Rosemount 3051
(22) Only valid with FOUNDATION fieldbus (output code F).
(23) The V5 option is not needed with the T1 option; external ground screw assembly is included with the T1 option.
(24) Only available with 4-20 mA HART Output (output code A) and Wireless output (output code X).
www.rosemount.com
31
Rosemount 3051
September 2014
Rosemount 3051CFP Integral Orifice Flowmeter
Rosemount 3051CFP Integral Orifice Flowmeters enable highly accurate flow
measurement in small line sizes. Integral Orifice utilize precision honed pipe section
for increased accuracy and self-centering plate design to prevent alignment errors
that magnify measurement inaccuracies in small line sizes.

Up to 1.75% of flow rate accuracy

Available in 1/2 to 11/2-in. (15 - 40 mm) line sizes

Fully assembled and leak tested for out-of-the-box installation

Power Advisory can proactively detect degraded electrical loop integrity issues.
(Option Code DA0)

Local Operator Interface with straightforward menus and built-in configuration
buttons (Option Code M4)
See “Specifications” on page 45 and options for more details on each configuration. Specification and selection of product materials,
options, or components must be made by the purchaser of the equipment. See page 54 for more information on Material Selection.
Additional information:
Specifications: page 45
Certifications: page 56
Dimensional Drawings: page 66
Table 5. Rosemount 3051CFP Integral Orifice Flowmeter Ordering Information
H The Standard offering represents the most common options. The starred options (H) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Model
Product description
3051CFP(1)
Integral Orifice Flowmeter
Measurement type
D
Differential Pressure
H
Body material
S
316 SST
H
1
H
H
H
Line size
005
010
015
/2-in. (15 mm)
1-in. (25 mm)
11/2-in. (40 mm)
Process connection
T1
S1(2)
P1
P2
D1
D2
D3
W1
W3
W6
A1
32
NPT Female Body (Not Available with Remote Thermowell and RTD)
Socket Weld Body (Not Available with Remote Thermowell and RTD)
Pipe Ends: NPT Threaded
Pipe ends: Beveled
Pipe Ends: Flanged, DIN PN16, slip-on
Pipe Ends: Flanged, DIN PN40, slip-on
Pipe Ends: Flanged, DIN PN100, slip-on
Pipe Ends: Flanged, RF, ANSI Class 150, weld-neck
Pipe Ends: Flanged, RF, ANSI Class 300, weld-neck
Pipe Ends: Flanged, RF, ANSI Class 600, weld-neck
Pipe Ends: Flanged, RF, ANSI Class 150, slip-on
H
H
H
H
H
H
H
H
H
H
www.rosemount.com
September 2014
Rosemount 3051
Table 5. Rosemount 3051CFP Integral Orifice Flowmeter Ordering Information
H The Standard offering represents the most common options. The starred options (H) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
A3
A6
R1
R3
R6
Pipe Ends: Flanged, RF, ANSI Class 300, slip-on
Pipe Ends: Flanged, RF, ANSI Class 600, slip-on
Pipe Ends: Flanged, RTJ, ANSI Class 150, slip-on
Pipe Ends: Flanged, RTJ, ANSI Class 300, slip-on
Pipe Ends: Flanged, RTJ, ANSI Class 600, slip-on
Orifice plate material
S
H
M
316 SST
Alloy C-276
Alloy 400
H
Bore size option
0066
0109
0160
0196
0260
0340
0150
0250
0345
0500
0630
0800
0295
0376
0512
0748
1022
1184
0010
0014
0020
0034
0.066-in. (1.68 mm) for 1/2-in. Pipe
0.109-in. (2.77 mm) for 1/2-in. Pipe
0.160-in. (4.06 mm) for 1/2-in. Pipe
0.196-in. (4.98 mm) for 1/2-in. Pipe
0.260-in. (6.60 mm) for 1/2-in. Pipe
0.340-in. (8.64 mm) for 1/2-in. Pipe
0.150-in. (3.81 mm) for 1-in. Pipe
0.250-in. (6.35 mm) for 1-in. Pipe
0.345-in. (8.76 mm) for 1-in. Pipe
0.500-in. (12.70 mm) for 1-in. Pipe
0.630-in. (16.00 mm) for 1-in. Pipe
0.800-in. (20.32 mm) for 1-in. Pipe
0.295-in. (7.49 mm) for 1 1/2-in. Pipe
0.376-in. (9.55 mm) for 1 1/2-in. Pipe
0.512-in. (13.00 mm) for 1 1/2-in. Pipe
0.748-in. (19.00 mm) for 1 1/2-in. Pipe
1.022-in. (25.96 mm) for 1 1/2-in. Pipe
1.184-in. (30.07 mm) for 1 1/2-in. Pipe
0.010-in. (0.25 mm) for 1/2-in. Pipe
0.014-in. (0.36 mm) for 1/2-in. Pipe
0.020-in. (0.51 mm) for 1/2-in. Pipe
0.034-in. (0.86 mm) for 1/2-in. Pipe
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
Transmitter connection platform
D3
D5
R3
R5
D4
D6
D7
R4
R6
Direct-mount, 3-Valve Manifold, SST
Direct-mount, 5-Valve Manifold, SST
Remote-mount, 3-Valve Manifold, SST
Remote-mount, 5-Valve Manifold, SST
Direct-mount, 3-Valve Manifold, Alloy C-276
Direct-mount, 5-Valve Manifold, Alloy C-276
Direct-mount, High Temperature, 5-Valve Manifold, SST
Remote-mount, 3-Valve Manifold, Alloy C-276
Remote-mount, 5-Valve Manifold, Alloy C-276
H
H
H
H
Differential pressure ranges
1
2
3
0 to 25 in H2O (0 to 62,16 mbar)
0 to 250 in H2O (0 to 621,60 mbar)
0 to 1000 in H2O (0 to 2,48 bar)
www.rosemount.com
H
H
H
33
Rosemount 3051
September 2014
Table 5. Rosemount 3051CFP Integral Orifice Flowmeter Ordering Information
H The Standard offering represents the most common options. The starred options (H) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Transmitter output
A(3)
F
W(4)
X(5)
M(6)
H
H
H
H
4–20 mA with digital signal based on HART Protocol
FOUNDATION fieldbus Protocol
PROFIBUS PA Protocol
Wireless
Low-Power 1-5 Vdc with Digital Signal Based on HART Protocol
Transmitter housing material
Conduit entry size
A
B
J
K
P(7)
D(8)
M(8)
1
Aluminum
Aluminum
SST
SST
Engineered polymer
Aluminum
SST
H
H
H
H
H
/2-14 NPT
M20 x 1.5
1
/2-14 NPT
M20 x 1.5
No conduit entries
G1/2
G1/2
Transmitter performance class
1
H
up to ±1.8% flow rate accuracy, 8:1 flow turndown, 5-year stability
Wireless options (requires Wireless Output Code X and Engineered Polymer Housing Code P)
Wireless transmit rate, operating frequency, and protocol
WA3
H
User Configurable Transmit Rate, 2.4GHz WirelessHART
Antenna and SmartPower
WP5
Internal Antenna, Compatible with Green Power Module (I.S. Power Module Sold Separately)
H
HART revision configuration (requires HART Protocol Output Code A)
HR5(3)
HR7(3)
Configured for HART Revision 5
Configured for HART Revision 7
H
H
Options (include with selected model number)
Extended product warranty
WR3
WR5
3-year limited warranty
5-year limited warranty
H
H
Transmitter body/bolt material
GT
High Temperature (850 °F / 454 °C)
Temperature sensor
RT(9)
Thermowell and RTD
Optional connection
G1
DIN 19213 Transmitter Connection
H
Pressure testing
P1(10)
Hydrostatic Testing with Certificate
Special cleaning
P2
PA
Cleaning for Special Services
Cleaning per ASTM G93 Level D (Section 11.4)
Material testing
V1
34
Dye Penetrant Exam
www.rosemount.com
September 2014
Rosemount 3051
Table 5. Rosemount 3051CFP Integral Orifice Flowmeter Ordering Information
H The Standard offering represents the most common options. The starred options (H) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Material examination
V2
Radiographic Examination
Flow calibration
WD(11)
Discharge Coefficient Verification
Special inspection
QC1
QC7
Visual & Dimensional Inspection with Certificate
Inspection and Performance Certificate
H
H
Material traceability certification
Q8
Material Traceability Certification per EN 10204:2004 3.1
H
Code conformance
J2(12)
J3(12)
J4(12)
ANSI/ASME B31.1
ANSI/ASME B31.3
ANSI/ASME B31.8
Materials conformance
J5(13)
NACE MR-0175 / ISO 15156
Country certification
J6
J1
European Pressure Directive (PED)
Canadian Registration
H
Transmitter calibration certification
Q4
Calibration Certificate for Transmitter
H
Quality certification for safety
QS(14)
QT(14)
Prior-use certificate of FMEDA data
Safety certified to IEC 61508 with certificate of FMEDA
H
H
Product certifications
E8
I1(15)
IA
N1
K8
E5
I5(16)
IE
K5
C6
I6(7)
K6
E7
I7
N7
K7
E2
I2
IB
K2
ATEX Flameproof, Dust
ATEX Intrinsic Safety and Dust
ATEX FISCO Intrinsic Safety; for FOUNDATION fieldbus or PROFIBUS PA protocols only
ATEX Type n and Dust
ATEX Flameproof, Intrinsic Safety, Type n, Dust (combination of E8, I1 and N1)
FM Explosion-proof, Dust Ignition-proof
FM Intrinsically Safe, Nonincendive
FM FISCO Intrinsically Safe; for FOUNDATION fieldbus or PROFIBUS PA protocols only
FM Explosion-proof, Dust Ignition-proof, Intrinsically Safe, and Division 2 (combination of E5 and I5)
CSA Explosion-proof, Dust Ignition-proof, Intrinsically Safe, and Division 2
CSA Intrinsically Safe
CSA and ATEX Explosion-proof, Intrinsically Safe, and Division 2 (combination of C6, E8, and I1)
IECEx Flameproof, Dust Ignition-proof
IECEx Intrinsic Safety
IECEx Type n
IECEx Flameproof, Dust Ignition-proof, Intrinsic Safety, and Type n (combination of I7, N7 and E7)
INMETRO Flameproof
INMETRO Intrinsic Safety
INMETRO FISCO intrinsically safe; for FOUNDATION fieldbus or PROFIBUS PA protocols only
INMETRO Flameproof, Intrinsic Safety
www.rosemount.com
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
35
Rosemount 3051
September 2014
Table 5. Rosemount 3051CFP Integral Orifice Flowmeter Ordering Information
H The Standard offering represents the most common options. The starred options (H) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
E3
I3
KB
KD
China Flameproof
China Intrinsic Safety
FM and CSA Explosion-proof, Dust Ignition-proof, Intrinsically Safe, and Division 2 (combination of K5 and C6)
CSA, FM, and ATEX Explosion-proof, Intrinsically Safe (combination of K5, C6, I1, and E8)
H
H
H
H
Sensor fill fluid and O-ring options
L1(17)
L2
LA(17)
H
H
H
Inert Sensor Fill Fluid
Graphite-Filled (PTFE) O-ring
Inert Sensor Fill Fluid and Graphite-Filled (PTFE) O-ring
Shipboard approvals
SBS(17)
SLL(17)(18)
H
American Bureau of Shipping
Lloyds Register (LR)
Display and interface options
M4(19)
M5
H
H
LCD Display with Local Operator Interface
LCD Display
Transient protection
T1(17)(20)
H
Transient terminal block
PlantWeb control functionality
A01(21)
H
FOUNDATION fieldbus Control Function Block Suite
PlantWeb diagnostic functionality
DA0(14)
D01(21)
H
H
Power Advisory HART Diagnostic
FOUNDATION fieldbus Diagnostic Suite
Low power output
C2
0.8-3.2 Vdc Output with Digital Signal Based on HART Protocol (Available with Output code M only)
Alarm levels
C4(14)
CN(14)
CR(14)
CS(14)
CT(14)
H
H
H
H
H
NAMUR Alarm and Saturation Levels, High Alarm
NAMUR Alarm and Saturation Levels, Low Alarm
Custom alarm and saturation signal levels, high alarm
Custom alarm and saturation signal levels, low alarm
Rosemount Standard low alarm
Ground screw
V5(17)(22)
H
External Ground Screw Assembly
Configuration buttons
D4(14)
DZ(23)
H
H
Analog Zero and Span
Digital Zero Trim
Typical model number:
3051CFP D S 010 W1 S 0500 D3 2 A A 1 E5 M5
(1) Select Configuration Buttons (option code D4 or DZ) or Local Operator Interface (option code M4) if local configuration buttons are required.
(2) To improve pipe perpendicularity for gasket sealing, socket diameter is smaller than standard pipe O.D.
(3) Option HR5 configures the HART output to HART Revision 5. Option HR7 configures the HART output to HART Revision 7. The device can be field configured to
HART Revision 5 or 7 if desired. HART Revision 5 is the default HART output.
(4) For local addressing and configuration, M4 (Local Operator Interface) is required.
36
www.rosemount.com
September 2014
Rosemount 3051
(5) Requires wireless options and engineered polymer housing. Available approvals are FM Intrinsically Safe, (option code I5), CSA Intrinsically Safe (option code I6),
ATEX Intrinsic Safety (option code I1), and IECEx Intrinsic Safety (option code I7).
(6) Only available with C6, E2, E5, I5, K5, KB and E8 approval. Not available with GE, GM, SBS, DA0, M4, D4, DZ, QT, HR5, HR7, CR, CS, CT.
(7) Only available with Wireless Output (output code X).
(8) Not available with Product certifications options E8, K8, E5, K5, C6, K6, E7, K7, E2, K2, E3, KB, KD.
(9) Thermowell Material is the same as the body material.
(10) Does not apply to Process Connection codes T1 and S1.
(11) Not available for bore sizes 0010, 0014, 0020, 0034, 0066, or 0109.
(12) Not available with DIN Process Connection codes D1, D2, or D3.
(13) Materials of Construction comply with metallurgical requirements within NACE MR0175/ISO for sour oil field production environments. Environmental limits
apply to certain materials. Consult latest standard for details. Selected materials also conform to NACE MR0103 for sour refining environments.
(14) Only available with HART 4-20 mA output (Option code A).
(15) Dust approval not applicable to output code X. See “IEC 62591 (WirelessHART Protocol)” on page 62 for wireless approvals
(16) Nonincendive certification not provided with Wireless output option code (X).
(17) Not available with Wireless Output (output code X).
(18) Only available with product certifications E7, E8, I1, I7, IA, K7, K8, KD, N1, N7.
(19) Not available with FOUNDATION fieldbus (Output Code F) or Wireless output (output code X) or Low Power (output code M).
(20) The T1 option is not needed with FISCO Product Certifications, transient protection is included with the FISCO Product Certification code IA, IB, and IE.
(21) Only valid with FOUNDATION fieldbus Output Code F.
(22) The V5 option is not needed with the T1 option; external ground screw assembly is included with the T1 option.
(23) Only available with 4-20 mA output (Output Code A) and Wireless output (Output Code X).
www.rosemount.com
37
Rosemount 3051
September 2014
Rosemount 3051L Level Transmitter
The Rosemount 3051L Level Transmitter combines the performance and capabilities of
Rosemount 3051 Transmitters with the reliability and quality of a direct mount seal in
one model number. 3051L Level Transmitters offer a variety of process connections,
configurations, and fill fluid types to meet a breadth of level applications. Capabilities of
a Rosemount 3051L Level Transmitter include:

Quantify and optimize total system performance (Option code QZ)

Tuned-System Assembly (Option code S1)

Power Advisory can proactively detect degraded electrical loop integrity issues
(Option Code DA0)

Local Operator Interface with straightforward menus and built-in configuration
buttons (Option Code M4)
3051L Level Transmitter
See Specifications and options for more details on each configuration. Specification and selection of product materials, options, or
components must be made by the purchaser of the equipment. See page 54 for more information on Material Selection.
Additional information:
Specifications: page 45
Certifications: page 56
Dimensional Drawings: page 66
Table 6. Rosemount 3051L Level Transmitter Ordering Information
H The Standard offering represents the most common options. The starred options (H) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Model
Transmitter type
3051L(1)
Level Transmitter
Pressure range
2
–250 to 250 inH2O (-621,60 to 621,60 mbar)
H
3
–1000 to 1000 inH2O (-2,48 to 2,48 bar)
H
4
–300 to 300 psi (-20,68 to 20,68 bar)
H
Transmitter output
A(2)
4–20 mA with Digital Signal Based on HART Protocol
H
F
FOUNDATION fieldbus Protocol
H
W(3)
PROFIBUS PA Protocol
H
X(4)
Wireless (requires wireless options and engineered polymer housing)
H
M(5)
Low-Power 1-5 Vdc with Digital Signal Based on HART Protocol
Process connection size, material, extension length (high side)
Code
Process connection size
Material
Extension length
G0(6)
2-in./DN 50/A
316L SST
Flush Mount Only
H
H0(6)
2-in./DN 50
Alloy C-276
Flush Mount Only
H
J0
2-in./DN 50
Tantalum
Flush Mount Only
H
A0(6)
3-in./DN 80
316L SST
Flush Mount
H
A2(6)
3-in./DN 80
316L SST
2-in./50 mm
H
(6)
3-in./DN 80
316L SST
4-in./100 mm
H
A4
38
www.rosemount.com
September 2014
Rosemount 3051
Table 6. Rosemount 3051L Level Transmitter Ordering Information
H The Standard offering represents the most common options. The starred options (H) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
A6(6)
3-in./DN 80
316L SST
6-in./150 mm
H
(6)
B0
4-in./DN 100
316L SST
Flush Mount
H
B2(6)
4-in./DN 100
316L SST
2-in./50 mm
H
B4(6)
4-in./DN 100
316L SST
4-in./100 mm
H
(6)
B6
4-in./DN 100
316L SST
6-in./150 mm
H
C0(6)
3-in./DN 80
Alloy C-276
Flush Mount
H
C2(6)
3-in./DN 80
Alloy C-276
2-in./50 mm
H
C4(6)
3-in./DN 80
Alloy C-276
4-in./100 mm
H
C6(6)
3-in./DN 80
Alloy C-276
6-in./150 mm
H
D0(6)
4-in./DN 100
Alloy C-276
Flush Mount
H
D2(6)
4-in./DN 100
Alloy C-276
2-in./50 mm
H
D4(6)
4-in./DN 100
Alloy C-276
4-in./100 mm
H
D6(6)
4-in./DN 100
Alloy C-276
6-in./150 mm
H
E0
3-in./DN 80
Tantalum
Flush Mount Only
H
F0
4-in./DN 100
Tantalum
Flush Mount Only
H
Mounting flange size, rating, material (high side)
Size
Rating
Material
M
2-in.
ANSI/ASME B16.5 Class 150
CS
H
A
3-in.
ANSI/ASME B16.5 Class 150
CS
H
B
4-in.
ANSI/ASME B16.5 Class 150
CS
H
N
2-in.
ANSI/ASME B16.5 Class 300
CS
H
C
3-in.
ANSI/ASME B16.5 Class 300
CS
H
D
4-in.
ANSI/ASME B16.5 Class 300
CS
H
P
2-in.
ANSI/ASME B16.5 Class 600
CS
H
E
3-in.
ANSI/ASME B16.5 Class 600
CS
H
X(6)
2-in.
ANSI/ASME B16.5 Class 150
316 SST
H
F(6)
3-in.
ANSI/ASME B16.5 Class 150
316 SST
H
G(6)
4-in.
ANSI/ASME B16.5 Class 150
316 SST
H
Y(6)
2-in.
ANSI/ASME B16.5 Class 300
316 SST
H
H(6)
3-in.
ANSI/ASME B16.5 Class 300
316 SST
H
(6)
4-in.
ANSI/ASME B16.5 Class 300
316 SST
H
Z(6)
2-in.
ANSI/ASME B16.5 Class 600
316 SST
H
L(6)
3-in.
ANSI/ASME B16.5 Class 600
316 SST
H
Q
DN 50
PN 10-40 per EN 1092-1
CS
H
R
DN 80
PN 40 per EN 1092-1
CS
H
S
DN 100
PN 40 per EN 1092-1
CS
H
V
DN 100
PN 10/16 per EN 1092-1
CS
H
K(6)
DN 50
PN 10-40 per EN 1092-1
316 SST
H
T(6)
DN 80
PN 40 per EN 1092-1
316 SST
H
U(6)
DN 100
PN 40 per EN 1092-1
316 SST
H
J
www.rosemount.com
39
Rosemount 3051
September 2014
Table 6. Rosemount 3051L Level Transmitter Ordering Information
H The Standard offering represents the most common options. The starred options (H) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Mounting flange size, rating, material (high side)
Size
Rating
Material
W(6)
DN 100
PN 10/16 per EN 1092-1
316 SST
H
7(6)
4 in.
ANSI/ASME B16.5 Class 600
316 SST
H
1
N/A
10K per JIS B2238
CS
2
N/A
20K per JIS B2238
CS
3
N/A
40K per JIS B2238
CS
4(6)
N/A
10K per JIS B2238
316 SST
5(6)
N/A
20K per JIS B2238
316 SST
(6)
N/A
40K per JIS B2238
316 SST
Seal fill fluid (high side)
Specific gravity
Temperature limits [ambient temperature of 70° F (21° C)]
D
Silicone 200
0.93
-49 to 401 °F (-45 to 205 °C)
H
F
Silicone 200 for
Vacuum
Applications
0.93
For use in vacuum applications below 14.7 psia (1 bar-a), refer to
vapor pressure curves in Rosemount DP Level Fill Fluid Specification
Technical Note (00840-2100-4016).
H
L
Silicone 704
1.07
32 to 401 °F (0 to 205 °C)
H
C
Silicone 704 for
Vacuum
Applications
1.07
For use in vacuum applications below 14.7 psia (1 bar-a), refer to
vapor pressure curves in Rosemount DP Level Fill Fluid Specification
Technical Note (00840-2100-4016).
H
R
Silicone 705
1.09
68 to 401 °F (20 to 205 °C)
H
V
Silicone 705 for
Vacuum
Applications
1.09
For use in vacuum applications below 14.7 psia (1 bar-a), refer to
vapor pressure curves in Rosemount DP Level Fill Fluid Specification
Technical Note (00840-2100-4016).
H
A
SYLTHERM™ XLT
0.85
-102 to 293 °F (-75 to 145 °C)
H
H
Inert (Halocarbon)
1.85
-49 to 320 °F (-45 to 160 °C)
H
G
Glycerine and Water
1.13
5 to 203 °F (-15 to 95 °C)
H
N
Neobee® M-20
0.92
5 to 401 °F (-15 to 205 °C)
H
P
Propylene Glycol and
Water
1.02
5 to 203 F (-15 to 95 °C)
H
6
Low pressure side
Configuration
Flange adapter Diaphragm material
Sensor fill fluid
11(6)
Gage
SST
316L SST
Silicone
H
21
Differential
SST
316L SST
Silicone
H
22(6)
Differential
SST
Alloy C-276
Silicone
H
2A(7)
Differential
SST
316L SST
Inert (Halocarbon)
H
2B
Differential
SST
Alloy C-276
Inert (Halocarbon)
H
31(6)
Tuned-System
Assembly with
Remote Seal
None
316L SST
Silicone
(requires Option Code S1)
H
(6)(7)
40
www.rosemount.com
September 2014
Rosemount 3051
Table 6. Rosemount 3051L Level Transmitter Ordering Information
H The Standard offering represents the most common options. The starred options (H) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
O-ring
A
H
Glass-filled PTFE
Housing material
Conduit entry size
A
Aluminum
½–14 NPT
H
B
Aluminum
M20 × 1.5
H
J
SST
½–14 NPT
H
K
SST
M20 × 1.5
H
H
P
(8)
Engineered polymer
No conduit entries
D(9)
Aluminum
G½
M(9)
SST
G½
Wireless options (requires Wireless Output Code X and Engineered Polymer Housing Code P)
Wireless transmit rate, operating frequency, and protocol
WA3
User Configurable Transmit Rate, 2.4GHz WirelessHART
H
Antenna and SmartPower
WP5
Internal Antenna, Compatible with Green Power Module (I.S. Power Module Sold Separately)
H
HART Revision configuration (requires HART Protocol Output Code A)
HR5(2)
Configured for HART Revision 5
H
HR7(2)
Configured for HART Revision 7
H
Options (include with selected model number)
Extended product warranty
WR3
3-year limited warranty
H
WR5
5-year limited warranty
H
PlantWeb control functionality
A01(10)
FOUNDATION fieldbus Control Function Block Suite
H
PlantWeb diagnostic functionality
DA0(18)
D01
(10)
Power Advisory HART Diagnostic
H
FOUNDATION fieldbus Diagnostics Suite
H
Seal assemblies
S1(11)
Assembled to One Rosemount 1199 Seal
H
Product certifications
ATEX Flameproof and Dust Certification
H
ATEX Intrinsic Safety and Dust
H
IA
ATEX FISCO Intrinsic Safety; for FOUNDATION fieldbus or PROFIBUS PA protocols only
H
N1
ATEX Type n Certification and Dust
H
K8
ATEX Flameproof, Intrinsic Safety, Type n, Dust (combination of E8, I1 and N1)
H
E4(13)
TIIS Flameproof
H
E5
FM Explosion-proof, Dust Ignition-proof
H
I5(14)
FM Intrinsically Safe, Nonincendive
H
IE
FM FISCO Intrinsically Safe; for FOUNDATION fieldbus or PROFIBUS PA protocols only
H
K5
FM Explosion-proof, Dust Ignition-Proof, Intrinsically Safe, and Division 2
H
E8
I1
(12)
www.rosemount.com
41
Rosemount 3051
September 2014
Table 6. Rosemount 3051L Level Transmitter Ordering Information
H The Standard offering represents the most common options. The starred options (H) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
C6
(8)
CSA Explosion-proof, Dust Ignition-proof, Intrinsically Safe, and Division 2
H
CSA Intrinsic Safety
H
K6
CSA and ATEX Explosion-proof, Intrinsically Safe, and Division 2 (combination of C6, E8, and I1)
H
E7
IECEx Flameproof, Dust Ignition-proof
H
I7
IECEx Intrinsic Safety
H
N7
IECEx Type n Certification
H
K7
IECEx Flameproof, Dust Ignition-proof, Intrinsic Safety, and Type n (combination of I7, N7 and E7)
H
E2
INMETRO Flameproof
H
I2
INMETRO Intrinsic Safety
H
IB
INMETRO FISCO intrinsically safe; for FOUNDATION fieldbus or PROFIBUS PA protocols only
H
K2
INMETRO Flameproof, Intrinsic Safety
H
E3
China Flameproof
H
I3
China Intrinsic Safety
H
N3
China Type n
H
EM
Technical Regulations Customs Union (EAC) Flameproof
H
IM
Technical Regulations Customs Union (EAC) Intrinsic Safety
H
KM
Technical Regulations Customs Union (EAC) Flameproof and Intrinsic Safety
H
KB
FM and CSA Explosion-proof, Dust Ignition Proof, Intrinsically Safe, and Division 2 (combination of K5 and C6)
H
KD
FM, CSA, and ATEX Explosion-proof, Intrinsically Safe (combination of K5, C6, I1, and E8)
H
I6
Shipboard approvals
SBS(7)
SBV(7)
American Bureau of Shipping
(15)
Bureau Veritas (BV)
SDN(7)
Det Norske Veritas
SLL(7)(15)
Lloyds Register (LR)
H
Bolting material
L4
Austenitic 316 SST Bolts
H
L5
ASTM A 193, Grade B7M bolts
H
L6
Alloy K-500 Bolts
H
L8
ASTM A 193 Class 2, Grade B8M Bolts
H
Display and interface options
M4(16)
LCD Display with Local Operator Interface
H
M5
LCD Display
H
Calibration certification
Q4
Calibration Certificate
H
QP
Calibration Certificate and tamper evident seal
H
QG(17)
Calibration Certificate and GOST Verification Certificate
H
Material traceability certification
Q8
Material Traceability Certification per EN 10204 3.1
H
Quality certification for safety
QS(18)
Prior-use certificate of FMEDA data
H
QT(18)
Safety certified to IEC 61508 with certificate of FMEDA
H
42
www.rosemount.com
September 2014
Rosemount 3051
Table 6. Rosemount 3051L Level Transmitter Ordering Information
H The Standard offering represents the most common options. The starred options (H) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
Toolkit total system performance reports
QZ
H
Seal System Performance Calculation Report
Conduit electrical connector
GE(7)
M12, 4-pin, Male Connector (eurofast)
H
GM(7)
A size Mini, 4-pin, Male Connector (minifast)
H
Configuration buttons
D4(18)
Analog Zero and Span
H
DZ(19)
Digital Zero Trim
H
Transient protection
T1(7)(20)
H
Transient Protection
Software configuration
C1(19)
Custom Software Configuration (completed CDS 00806-0100-4007 for wired and 00806-0100-4100 for wireless
required with order)
H
Low power output
C2
0.8-3.2 Vdc Output with Digital Signal Based on HART Protocol (available with Output code M only)
Alarm levels
C4(18)
NAMUR alarm and saturation levels, high alarm
H
CN(18)
NAMUR alarm and saturation levels, low alarm
H
CR(18)
Custom alarm and saturation signal levels, high alarm (requires C1 and Configuration Data Sheet)
H
CS(18)
Custom alarm and saturation signal levels, low alarm (requires C1 and Configuration Data Sheet)
H
CT(18)
Rosemount Standard low alarm
H
Conduit plug
DO(7)
H
316 SST Conduit Plug
Ground screw
V5(7)(21)
H
External Ground Screw Assembly
Lower housing flushing connection options
Ring material
Number
Size (NPT)
F1
316 SST
1
1
/4-18 NPT
H
F2
316 SST
2
1/4-18 NPT
H
1
1
H
F3
Alloy C-276
/4-18 NPT
F4
Alloy C-276
2
1
/4-18 NPT
H
F7
316 SST
1
1/2-14 NPT
H
2
1
H
F8
316 SST
/2-14 NPT
F9
Alloy C-276
1
1
/2-14 NPT
H
F0
Alloy C-276
2
1/2-14 NPT
H
Lower housing intermediate gasket material
S0
No Gasket for lower housing
H
SY(22)
Thermo-Tork TN-9000
H
www.rosemount.com
43
Rosemount 3051
September 2014
Table 6. Rosemount 3051L Level Transmitter Ordering Information
H The Standard offering represents the most common options. The starred options (H) should be selected for best delivery.
__The Expanded offering is subject to additional delivery lead time.
NACE certificate
Q15(23)
(23)
Q25
Certificate of Compliance to NACE MR0175/ISO 15156 for wetted materials
H
Certificate of Compliance to NACE MR0103 for wetted materials
H
Typical model number: 3051L 2 A A0 D 21 A A F1
(1) Select Configuration Buttons (option code D4 or DZ) or Local Operator Interface (option code M4) if local configuration buttons are required.
(2) Option HR5 configures the HART output to HART Revision 5. Option HR7 configures the HART output to HART Revision 7. The device can be field configured to
HART Revision 5 or 7 if desired. HART Revision 5 is the default HART output.
(3) Option code M4 - LCD Display with Local Operator Interface required for local addressing and configuration.
(4) Requires wireless options and engineered polymer housing. Available approvals are FM Intrinsically Safe, (option code I5), CSA Intrinsically Safe (option code I6),
ATEX Intrinsic Safety (option code I1), IECEx Intrinsic Safety (option code I7) and EAC Intrinsic Safety (option code IM).
(5) Only available with C6, E2, E5, I5, K5, KB and E8 approval. Not available with GE, GM, SBS, DA0, M4, D4, DZ, QT, HR5, HR7, CR, CS, CT.
(6) Materials of Construction comply with metallurgical requirements highlighted within NACE MR0175/ISO 15156 for sour oil field production environments.
Environmental limits apply to certain materials. Consult latest standard for details. Selected materials also conform to NACE MR0103 for sour refining
environments.
(7) Not available with Wireless output (output code X).
(8) Only available with Wireless output (output code X).
(9) Not available with Product certifications options E8, K8, E5, K5, C6, K6, E7, K7, E2, K2, E3, KB, KD.
(10) Only valid with FOUNDATION fieldbus output (output code F).
(11) “Assemble-to” items are specified separately and require a completed model number.
(12) Dust approval not applicable to output code X. See “IEC 62591 (WirelessHART Protocol)” on page 62 for wireless approvals.
(13) Only available with output codes A - 4-20mA HART, F - FOUNDATION fieldbus, and W - PROFIBUS PA. Also only available with G1/2 housing thread types.
(14) Nonincendive certification not provided with Wireless output option code (X).
(15) Only available with product certifications E7, E8, I1, I7, IA, K7, K8, KD, N1, N7.
(16) Not available with FOUNDATION fieldbus (Output Code F) or Wireless output (Output Code X) or Low Power (Output Code M).
(17) Contact an Emerson Process Management representative for availability.
(18) Only available with HART 4-20 mA output (output code A).
(19) Only available with 4-20 mA HART output (Output Code A) and Wireless output (Output Code X).
(20) The T1 option is not needed with FISCO Product Certifications; transient protection is included in the FISCO product certification codes IA, IB, and IE.
(21) The V5 option is not needed with the T1 option; external ground screw assembly is included with the T1 option.
(22) Gasket provided when lower housing is ordered.
(23) NACE compliant wetted materials are identified by Footnote 6.
44
www.rosemount.com
September 2014
Rosemount 3051
Specifications
Performance specifications
This product data sheet covers HART, Wireless, FOUNDATION fieldbus, and PROFIBUS PA protocols unless specified.
Conformance to specification [±3 (Sigma)]
Technology leadership, advanced manufacturing techniques, and statistical process control ensure specification conformance to at
least ±3.
Reference accuracy
Stated reference accuracy equations include terminal based linearity, hysteresis, and repeatability. For wireless, FOUNDATION fieldbus
and PROFIBUS PA devices, use calibrated range in place of span.
Models
3051C
Rosemount 3051and WirelessHART
+/-0.065% of span
 URL- % of Span
Range 5 For spans less than 10:1, accuracy =  0.015 + 0.005  -------------Span
Ranges 2-4 ± 0.04% of span(1)
URL 
- % of Span
For spans less than 10:1(2), accuracy =  0.015 + 0.005  -------------Span
Range 1 ± 0.10% of span
URL 
- % of Span
For spans less than 15:1, accuracy =  0.025 + 0.005  -------------Span
Range 0 (CD) ± 0.10% of span
For spans less than 2:1, accuracy = ± 0.05% of URL
3051CA
± 0.04% of span(1)
URL
Ranges 1-4 For spans less than 10:1, accuracy =  0.0075  --------------- % of Span
Span
3051T
± 0.04% of span(1)
 URL- % of Span
Ranges 1-4 For spans less than 10:1, accuracy =  0.0075  -------------Span
Range 5 ± 0.075% of span
URL 
- % of Span
For spans less than 10:1, accuracy =  0.0075  -------------Span
3051L
± 0.075% of span
URL 
- % of Span
Ranges 2-4 For spans less than 10:1, accuracy =  0.025 + 0.005  -------------Span
(1) For output code W and M, ±0.065% span.
(2) For output code F, for span less than 5:1.
Flow performance - flow reference accuracy(1)
3051CFA Annubar Flowmeter
Ranges 2-3
±1.80% of Flow Rate at 8:1 flow turndown
3051CFC_A Compact Annubar Flowmeter – Annubar Option A
Ranges 2-3
Uncalibrated
Calibrated
±2.10% of Flow Rate at 8:1 flow turndown
±1.80% of Flow Rate at 8:1 flow turndown
3051CFC_C Compact Orifice Flowmeter – Conditioning Option C
Ranges 2-3
www.rosemount.com
 = 0.4
 = 0.50, 0.65
±1.75% of Flow Rate at 8:1 flow turndown
±1.95% of Flow Rate at 8:1 flow turndown
45
Rosemount 3051
September 2014
Flow performance - flow reference accuracy(1)
3051CFC_P Compact Orifice Flowmeter – orifice type option P(2)
Ranges 2-3
 = 0.4
 = 0.65
±2.00% of Flow Rate at 8:1 flow turndown
±2.00% of Flow Rate at 8:1 flow turndown
3051CFP Integral Orifice Flowmeter
Ranges 2-3
 <0.1
0.1<  <0.2
0.2<  <0.6
0.6<  <0.8
±3.00% of Flow Rate at 8:1 flow turndown
±1.95% of Flow Rate at 8:1 flow turndown
±1.75% of Flow Rate at 8:1 flow turndown
±2.15% of Flow Rate at 8:1 flow turndown
(1) Accuracy over range of use is always application dependent. Range 1 flowmeters may experience an additional uncertainty up to 0.9%.
Consult your Emerson Process Management Representative for exact specifications.
(2) Applicable to 2-in. to 12-in. line sizes. For smaller line sizes, see the Rosemount DP Flowmeters and Primary Elements PDS
(00813-0100-4485).
Total performance
Total performance is based on combined errors of reference accuracy, ambient temperature effect, and static pressure effect at
normal operating conditions (70% of span typical reading, 740 psi (51,02 bar) line pressure).
For ±50 °F (28 °C) temperature changes; 0-100% relative humidity, from 1:1 to 5:1 rangedown
Models
3051C
Ranges 2-5
3051T
Ranges 1-4
3051L
Total performance(1)
± 0.14% of span
± 0.14% of span
Use Instrument Toolkit™ or the QZ option to quantify the total
Ranges 2-4 performance of a remote seal assembly under operating conditions.
(1) For output code W, F and M, total performance is ±0.15% of span.
Long term stability
Models
Long term stability
3051C
Ranges 2-5
±0.2% of URL for 10 years
±50 °F (28 °C) temperature changes, and up to 1000 psi (68,95 bar) line pressure.
3051CD, 3051CG Low/Draft Range
±0.2% of URL for 1 year
Ranges 0-1
3051CA Low Range
±0.2% of URL for 10 years
Range 1 ±50 °F (28 °C) temperature changes, and up to 1000 psi (68,95 bar) line pressure.
3051T
Ranges 1-4
46
±0.2% of URL for 10 years
±50 °F (28 °C) temperature changes, and up to 1000 psi (68,95 bar) line pressure.
www.rosemount.com
September 2014
Rosemount 3051
Dynamic performance
4 - 20 mA HART(1)
FOUNDATION fieldbus
Typical HART transmitter response
and PROFIBUS PA
time
protocols(3)
Total Response Time (Td + Tc)(2):
3051C
Ranges 2-5
Range 1
Range 0
3051T
3051L
100 ms
255 ms
700 ms
100 ms
See Instrument Toolkit
152 ms
307 ms
N/A
152 ms
See Instrument Toolkit
Transmitter Output vs. Time
Pressure
10
Dead Time (Td)
45 ms (nominal)
97 ms
Update Rate(4)
22 times per second
22 times per second
(1) Dead time and update rate apply to all models and ranges; analog output only.
Td
Tc
Td = Dead Time
Tc = Time Constant
Response Time = Td +Tc
63.2% of Total
Step Change
36.
0%
Time
(2) Nominal total response time at 75 °F (24 °C) reference conditions.
(3) Transducer block response time, Analog Input block execution time not included.
(4) Does not apply to wireless (output Code X). See “Wireless (output code X)” on page 52
for wireless update rate.
Line pressure effect per 1000 psi (68,95 bar)
For line pressures above 2000 psi (137,90 bar) and Ranges 4-5, see user manual
(Document number 00809-0100-4007 for HART, 00809-0100-4100 for WirelessHART, 00809-0100-4774 for
FOUNDATION fieldbus, and 00809-0100-4797 for PROFIBUS PA).
Models
Line pressure effect
3051CD, 3051CF
Zero Error
Ranges 2-3 ±0.05% of URL/1000 psi (68,95 bar) for line pressures from 0 to 2000 psi (0 to 137,90 bar)
Range 1 ±0.25% of URL/1000 psi (68,95 bar) for line pressures from 0 to 2000 psi (0 to 137,90 bar)
Range 0 ±0.125% of URL/100 psi (6,89 bar) for line pressures from 0 to 750 psi (0 to 51,71 bar)
Span Error
Ranges 2-3 ±0.1% of reading/1000 psi (68,95 bar)
Range 1 ±0.4% of reading/1000 psi (68,95 bar)
Range 0 ±0.15% of reading/100 psi (68,95 bar)
Ambient temperature effect per 50 °F (28 °C)
Models
Ambient temperature effect
3051C
Ranges 2-5
Range 1
Range 0
3051CA
Ranges 1-4
3051T
Range 2-4
Range 1
Range 5
3051L
www.rosemount.com
±(0.0125% URL + 0.0625% span) from 1:1 to 5:1
±(0.025% URL + 0.125% span) from 5:1 to 150:1
±(0.1% URL + 0.25% span) from 1:1 to 30:1
±(0.14% URL + 0.15% span) from 30:1 to 50:1
±(0.25% URL + 0.05% span) from 1:1 to 30:1
±(0.025% URL + 0.125% span) from 1:1 to 30:1
±(0.035% URL + 0.125% span) from 30:1 to 150:1
±(0.025% URL + 0.125% span) from 1:1 to 30:1
±(0.035% URL + 0.125% span) from 30:1 to 150:1
±(0.025% URL + 0.125% span) from 1:1 to 10:1
±(0.05% URL + 0.125% span) from 10:1 to 100:1
±(0.1% URL + 0.15% span) from 1:1 to 5:1
See Instrument Toolkit software.
47
Rosemount 3051
September 2014
Mounting position effects
Models
Mounting position effects
3051C
3051CA, 3051T
Zero shifts up to ±1.25 inH2O (3,11 mbar), which can be calibrated out. No span effect.
Zero shifts up to ±2.5 inH2O (6,22 mbar), which can be calibrated out. No span effect.
With liquid level diaphragm in vertical plane, zero shift of up to ±1 inH2O (2,49 mbar). With
diaphragm in horizontal plane, zero shift of up to ±5 inH2O (12,43 mbar) plus extension length on
extended units. All zero shifts can be calibrated out. No span effect.
3051L
Vibration effect
Less than ±0.1% of URL when tested per the requirements of IEC60770-1: 1999 field or pipeline with high vibration level
(10-60 Hz 0.21 mm displacement peak amplitude / 60-2000 Hz 3g).
Power supply effect
Less than ±0.005% of calibrated span per volt change.
Electromagnetic compatibility (EMC)
Meets all relevant requirements of EN61326-1:2006 and Namur NE-21.(1)
(1)
NAMUR NE-21 does not apply to wireless output code X.
Transient protection (option code T1)
Tested in accordance with IEEE C62.41.2-2002, Location Category B
6 kV crest (0.5 s - 100 kHz)
3 kA crest (8 × 20 s)
6 kV crest (1.2 × 50 s)
48
www.rosemount.com
September 2014
Rosemount 3051
Functional specifications
Range and sensor limits
Table 7. 3051CD, 3051CG, 3051CF, and 3051L Range and Sensor Limits
Range(1)
Minimum span
0
1
2
3
4
5
Range and sensor limits
Lower (LRL)
3051CD,
3051CG,
3051CF,
3051L(2)
0.10 inH2O
(0,24 mbar)
0.50 inH2O
(1,24 mbar)
1.67 inH2O
(4,15 mbar)
6.67 inH2O
(16,58 mbar)
2.00 psi
(137,89 mbar)
13.33 psi
(919,01 mbar)
Upper
(URL)
3051CD
differential
3051CF
Flowmeters
3.00 inH2O
(7,45 mbar)
25.00 inH2O
(62,16 mbar)
250.00 inH2O
(621,60 mbar)
1000.00 inH2O
(2,48 bar)
300.00 psi
(20,68 bar)
2000.00 psi
(137,89 bar)
-3.00 inH2O
(-7,45 mbar)
-25.00 inH2O
(-62,16 mbar)
-250.00 inH2O
(-621,60 mbar)
-1000.00 inH2O
(-2,48 bar)
-300.00 psi
(-20,68 bar)
- 2000.00 psi
(-137,89 bar)
3051CG
gage(3)
3051L
differential
3051L gage(3)
N/A
N/A
N/A
-25.00 inH2O
N/A
(-62,16 mbar)
-250.00 inH2O -250.00 inH2O
(-621,60 mbar) (-621,60 mbar)
0.50 psia
-1000.00 inH2O
(34,47 mbar)
(-2,48 bar)
0.50 psia
-300.00 psi
(34,47 mbar)
(-20,68 bar)
0.50 psia
N/A
(34,47 mbar)
N/A
-250.00 inH2O
(-621,60 mbar)
0.50 psia
(34,47 mbar)
0.50 psia
(34,47 mbar)
N/A
(1) Range 0 only available with 3051CD. Range 1 only available with 3051CD, 3051CG, or 3051CF. inH2O referenced at 68 degrees Fahrenheit.
(2) For outputs options W and M, minimum span are: range 1 - 0.50 inH2O (1,24 mbar), range 2 - 2.50 inH2O (6,21 mbar), range 3 - 10.00 inH2O
(24,86 mbar), range 4 - 3.00 psi (0,21 bar), range 5 - 20.00 psi (1,38 bar).
(3) Assumes atmospheric pressure of 14.7 psig.
Table 8. 3051CA and 3051T Range and Sensor Limits
1
2
3
4
5
3051T
Range and sensor limits
Upper
(URL)
Lower
(LRL)
0.30 psi
(20,68 mbar)
1.00 psi
(68,94 mbar)
5.33 psi
(367,49 mbar)
26.67 psi
(1,83 bar)
30 psia
(2,06 bar)
150 psia
(10,34 bar)
800 psia
(55,15 bar)
4000 psia
(275,79 bar)
0 psia
(0 bar)
0 psia
(0 bar)
0 psia
(0 bar)
0 psia
(0 bar)
N/A
N/A
N/A
Range
Range
3051CA
Minimum span(1)
1
2
3
4
5
Minimum span(1)
Range and sensor limits
Upper
(URL)
0.30 psi
(20,68 mbar)
1.00 psi
(68,94 mbar)
5.33 psi
(367,49 mbar)
26.67 psi
(1,83 bar)
2000.00 psi
(137,89 bar)
30.00 psi
(2,06 bar)
150.00 psi
(10,34 bar)
800.00 psi
(55,15 bar)
4000.00 psi
(275,79 bar)
10000.00 psi
(689,47 bar)
Lower(2)
Lower
(LRL) (gage)
(LRL)
(absolute)
0 psia
(0 bar)
0 psia
(0 bar)
0 psia
(0 bar)
0 psia
(0 bar)
0 psia
(0 bar)
-14.70 psig
(-1,01 bar)
-14.70 psig
(-1,01 bar)
-14.70 psig
(-1,01 bar)
-14.70 psig
(-1,01 bar)
-14.70 psig
(-1,01 bar)
(1) For output options W and M, minimum span are: range 2 - 1.50 psi(0,10 bar), range 3 - 8.00 psi (0,55 bar), range 4 - 40.00 psi (2,75 bar), range 5 for 3051T
- 2000.00 psi (137,89 bar)
(2) Assumes atmospheric pressure of 14.7 psig.
www.rosemount.com
49
Rosemount 3051
September 2014
Service
External power supply required. Standard transmitter (4-20mA)
operates on 10.5-42.4 Vdc with no load
Local operator interface
The LOI utilizes a 2 button menu with internal and external
configuration buttons. Internal buttons are always
configured for Local Operator Interface. External Buttons can
be configured for either LOI (option code M4), Analog Zero
and Span (option code D4) or Digital Zero Trim (option code
DZ). See Rosemount 3051 product manual
(00809-0100-4007) for LOI configuration menu.
Load limitations
FOUNDATION fieldbus (output code F)
Maximum loop resistance is determined by the voltage level of
the external power supply described by:
Power supply
Liquid, gas, and vapor applications
4-20 mA HART (output code A)
Power supply
Max. Loop Resistance = 43.5 (Power Supply Voltage – 10.5)
Load (s)
1387
External power supply required; transmitters operate on 9.0 to
32.0 V dc transmitter terminal voltage. FISCO transmitters
operate on 9.0 to 17.5 V dc.
Current draw
17.5 mA for all configurations (including LCD display option)
1000
500
Indication
Operating
Region
Optional two line LCD display
0
10.5
20
30
Voltage (Vdc)
FOUNDATION fieldbus block execution times
42.4(1)
Block
Execution time
Resource
N/A
Sensor and SPM Transducer
N/A
LCD Display
N/A
Analog Input 1, 2
20 milliseconds
PID
25 milliseconds
Configuration buttons need to be specified:
Digital Zero trim (option code DZ) changes digital value of the
transmitter and is used for performing a sensor zero trim.
Analog Zero Span (option code D4) changes analog value and
can be used to rerange the transmitter with an applied pressure.
Input Selector
20 milliseconds
Arithmetic
20 milliseconds
Signal Characterizer
20 milliseconds
Integrator
20 milliseconds
Output
Output Splitter
20 milliseconds
Two-wire 4-20mA, user selectable for linear or square root
output. Digital process variable superimposed on 4-20 mA
signal, available to any host that conforms to HART protocol.
The 3051 comes with Selectable HART Revisions. Digital
communications based on HART Revision 5 (default) or Revision
7 (option code HR7) protocol can be selected. The HART revision
can be switched in the field using any HART based configuration
tool or the optional local operator interface (M4).
Control Selector
20 milliseconds
Communication requires a minimum
loop resistance of 250 ohms.
(1) For CSA approval, power supply must not exceed 42.4 V.
Indication
Optional two line LCD/LOI Display
Optional configuration buttons
Power advisory diagnostics
Power Advisory Diagnostics pro-actively detect and notify
you of degraded electrical loop integrity before it can affect
your process operation. Example loop problems that can be
detected include water in the terminal compartment,
corrosion of terminals, improper grounding, and unstable
power supplies.
The Device Dashboard presents the diagnostics in a
graphical, task-based interface that provides single-click
access to critical process/device information and descriptive
graphical troubleshooting.
50
FOUNDATION fieldbus parameters
Links
25 (max.)
Virtual Communications Relationships (VCR)
20 (max.)
FOUNDATION fieldbus function blocks (option A01)
Resource block
The resource block contains diagnostic, hardware, and
electronics information. There are no linkable inputs or
outputs to the Resource Block.
Sensor transducer block
The sensor transducer block contains sensor information
and the ability to calibrate the pressure sensor or recall
factory calibration.
www.rosemount.com
September 2014
LCD transducer block
The LCD transducer block is used to configure the LCD
display meter.
Analog input block
The analog input (AI) function block processes the
measurements from the sensor and makes them available
to other function blocks. The output value from the AI
block is in engineering units and contains a status
indicating the quality of the measurement. The AI Block is
widely used for scaling functionality.
Input selector block
The input selector (ISEL) function block can be used to
select the first good, hot backup, maximum, minimum,
or average of as many as eight input values and place it at
the output. The block supports signal status propagation.
Integrator block
The integrator (INT) function block integrates one or two
variables over time. The block compares the integrated or
accumulated value to pre-trip and trip limits and
generates discrete output signals when the limits are
reached.
The Integrator Block is used as a totalizer. This block will
accept up to two inputs, has six options how to totalize
the inputs, and two trip outputs.
Arithmetic block
The arithmetic (ARTH) function block provides the ability
to configure a range extension function for a primary
input. It can also be used to compute nine different
arithmetic functions including flow with partial density
compensation, electronic remote seals, hydrostatic tank
gaging, ratio control, and others.
Signal characterizer block
The signal characterizer (SGCR) function block
characterizes or approximates any function that defines
an input/output relationship. The function is defined by
configuring as many as twenty X,Y coordinates. The block
interpolates an output value for a given input value using
the curve defined by the configured coordinates. Two
separate analog input signals can be processed
simultaneously to give two corresponding separate
output values using the same defined curve.
PID block
The PID function block combines all of the necessary logic
to perform proportional/integral/derivative (PID) control.
The block supports mode control, signal scaling and
limiting, feed forward control, override tracking, alarm
limit detection, and signal status propagation.
Control selector block
The control selector function block selects one of two or
three inputs to be the output. The inputs are normally
connected to the outputs of PID or other function blocks.
One of the inputs would be considered normal and the
other two overrides.
Rosemount 3051
Output splitter block
The output splitter function block provides the capability
to drive two control outputs from a single input. It takes
the output of one PID or other control block to control
two valves or other actuators.
Backup Link Active Scheduler (LAS)
The transmitter can function as a Link Active Scheduler if the
current link master device fails or is removed from the
segment.
FOUNDATION fieldbus Diagnostics Suite
(option code D01)
The 3051C FOUNDATION fieldbus Diagnostics Suite features
SPM technology to detect changes in the process, process
equipment, or installation conditions (such as plugged
impulse lines) of the transmitter. This is done by modeling the
process noise signature (using the statistical values of mean
and standard deviation) under normal conditions and then
comparing the baseline values to current values over time. If a
significant change in the current values is detected, the
transmitter can generate an alert.
PROFIBUS PA (output code W)
Profile version
3.02
Power supply
External power supply required; transmitters operate on 9.0
to 32.0 V dc transmitter terminal voltage. FISCO transmitters
operate on 9.0 to 17.5 V dc.
Current draw
17.5 mA for all configurations (including LCD display option)
Output update rate
Four times per second
Standard function blocks
Analog input (AI block)
The AI function block processes the measurements and
makes them available to the host device. The output
value from the AI block is in engineering units and
contains a status indicating the quality of the
measurement.
Physical block
The physical block defines the physical resources of the
device including type of memory, hardware, electronics
and diagnostic information.
Transducer block
Contains actual sensor measurement data including the
sensor diagnostics and the ability to trim the pressure
sensor or recall factory defaults.
Indication
Optional 2-line LCD display
www.rosemount.com
51
Rosemount 3051
September 2014
Local operator interface
Minimum load impedance
The LOI utilizes a 2 button menu with external configuration
buttons.
100 k  (Vout wiring)
Wireless (output code X)
Optional 5-digit LCD display
Output
Overpressure limits
IEC 62591 (WirelessHART), 2.4 GHz DSSS
Wireless radio (internal antenna, WP5 option)
Indication
Rosemount 3051CD/CG/CF
•
Range 0: 750 psi (51,71 bar)
Frequency: 2.400 - 2.485 GHz
•
Range 1: 2000 psig (137,90 bar)
•
Channels: 15
•
•
Modulation: IEEE 802.15.4 compliant DSSS
Ranges 2-5: 3626 psig (250,00 bar)
4500 psig (310,26 bar) for option code P9
•
Transmission: Maximum of 10 dBm EIRP
•
Rosemount 3051CA
Local display
•
Range 1: 750 psia (51,71 bar)
The optional 3-line, 7-digit LCD display can display
user-selectable information such as primary variable in
engineering units, scaled variable, percent of range, sensor
module temperature, and electronics temperature. The display
updates based on the wireless update rate.
•
Range 2: 1500 psia (103,42 bar)
•
Range 3: 1600 psia (110,32 bar)
•
Range 4: 6000 psia (413,69 bar)
Rosemount 3051TG/TA
•
Range 1: 750 psi (51,71 bar)
Digital zero trim
•
Range 2: 1500 psi (103,42 bar)
Digital Zero trim (option DZ) is an offset adjustment to
compensate for mounting position effects, up to 5% of URL.
•
Range 3: 1600 psi (110,32 bar)
•
Range 4: 6000 psi (413,69 bar)
Update rate
•
Range 5: 15000 psi (1034,21 bar)
User selectable 1 sec. to 60 min.
Wireless sensor module for in-line transmitters
The 3051 Wireless transmitter requires the engineered polymer
housing to be selected. The standard sensor module will come
with aluminum material. If stainless steel is required, the option
WSM must be selected.
Power module
Field replaceable, keyed connection eliminates the risk of
incorrect installation, Intrinsically Safe Lithium-thionyl chloride
Power Module with PBT/PC enclosure. Ten-year life at one
minute update rate.(1)
(1)
Reference conditions are 70 °F (21 °C), and routing data for three
additional network devices.
Note: Continuous exposure to ambient temperature limits of -40 °F or
185 °F (-40 °C or 85 °C) may reduce specified life by less than 20
percent.
Low power output
1-5 Vdc HART Low Power (output code M)
Output
Three-wire 1-5 Vdc (option code C2) user-selectable output.
Also user selectable for linear or square root output
configuration. Digital process variable superimposed on voltage
signal, available to any host conforming to the HART protocol.
Low-power transmitter operates on 6-12 Vdc with no load.
Power consumption
3.0 mA, 18-36 mW
For 3051L or Level Flange Option Codes FA, FB, FC, FD, FP, and
FQ, limit is 0 psia to the flange rating or sensor rating, whichever
is lower.
Table 9. 3051L and Level Flange Rating Limits
Standard
Type
CS rating SST rating
ANSI/ASME
Class 150
285 psig
275 psig
ANSI/ASME
Class 300
740 psig
720 psig
ANSI/ASME
Class 600
1480 psig
1440 psig
At 100 °F (38 °C), the rating decreases
with increasing temperature, per ANSI/ASME B16.5.
DIN
PN 10-40
40 bar
40 bar
DIN
PN 10/16
16 bar
16 bar
DIN
PN 25/40
40 bar
40 bar
At 248 °F (120 °C), the rating decreases
with increasing temperature, per DIN 2401.
Static pressure limit
Rosemount 3051CD only
Operates within specifications between static line pressures of
0.5 psia and 3626 psig (4500 psig (310, 26 bar) for Option Code
P9).
Range 0: 0.5 psia and 750 psig (0,03 bar and 51,71 bar)
Range 1: 0.5 psia and 2000 psig (0,03 bar and 137, 90 bar)
Burst pressure limits
3051C, 3051CF Coplanar or
traditional process flange
10081 psig (695,06 bar)
52
www.rosemount.com
September 2014
Rosemount 3051
3051T In-Line
Process
Ranges 1-4: 11016 psi (759,53 bar)
Range 5: 26016 psig (1793,74 bar)
At atmospheric pressures and above. See Table 10.
Table 10. 3051 Process Temperature Limits
Failure mode alarm
3051CD, 3051CG, 3051CF, 3051CA
HART 4-20 mA (output option code A)
If self-diagnostics detect a sensor or microprocessor failure, the
analog signal is driven either high or low to alert the user. High or
low failure mode is user-selectable with a jumper/switch on the
transmitter. The values to which the transmitter drives its
output in failure mode depend on whether it is configured to
standard, NAMUR-compliant, or custom levels (see Alarm
Configuration below). The values for each are as follows:
High alarm
Default
NAMUR compliant(1)
Custom levels(2)
Low alarm
21.75 mA
3.75 mA
22.5 mA
3.6 mA
20.2 - 23.0 mA 3.4 - 3.8 mA
(1)
Analog output levels are compliant with NAMUR
recommendation NE 43, see option codes C4 or C5.
(2)
Low alarm must be 0.1 mA less than low saturation and high
alarm must be 0.1 mA greater than high saturation.
Output code M
If self-diagnostics detect a gross transmitter failure, the analog
signal will be driven either below 0.94 V or above 5.4 V to alert
the user (below 0.75 V or above 4.4 V for Option C2). High or low
alarm signal is user-selectable by internal jumper.
Output code F, W, and X
If self-diagnostics detect a gross transmitter failure, that
information gets passed as an alert and a status along with the
process variable.
Silicone Fill Sensor(1)
with Coplanar Flange
with Traditional Flange
with Level Flange
with 305 Integral
Manifold
Inert Fill Sensor(1)(4)
–40 to 250 °F (–40 to 121 °C)(2)
–40 to 300 °F (–40 to 149 °C)(2)(3)
–40 to 300 °F (–40 to 149 °C)(2)
–40 to 300 °F (–40 to 149 °C)(2)
–40 to 185 °F (–40 to 85 °C)(5)(6)
3051T (process fill fluid)
Silicone Fill Sensor(1)
Inert Fill Sensor(1)
–40 to 250 °F (–40 to 121 °C)(2)
–22 to 250 °F (–30 to 121 °C)(2)
3051L low-side
temperature limits
Silicone Fill Sensor(1)
Inert Fill Sensor(1)
–40 to 250 °F (–40 to 121 °C)(2)
-40 to 185 °F (–40 to 85 °C)(5)
3051L high-side temperature limits (process fill fluid)
SYLTHERM XLT
D.C. Silicone 704®
D.C. Silicone 200
Inert
Glycerin and Water
Neobee M-20
Propylene Glycol and
Water
–102 to 293 °F (–75 to 145 °C)
32 to 401 °F (0 to 205 °C)
–49 to 401 °F (–45 to 205 °C)
–49 to 320 °F (–45 to 160 °C)
5 to 203 °F (–15 to 95 °C)
5 to 401 °F (–15 to 205 °C)
5 to 203 °F (–15 to 95 °C)
(1) Process temperatures above 185 °F (85 °C) require derating the ambient
limits by a 1.5:1 ratio.
Temperature limits
Ambient
(2) 220 °F (104 °C) limit in vacuum service; 130 °F (54 °C) for pressures
below 0.5 psia.
-40 to 185 °F (-40 to 85 °C)
With LCD display(1)(2): -40 to 176 °F (-40 to 80 °C)
(3) 3051CD0 process temperature limits are –40 to 212 °F (–40 to 100 °C).
(1)
For the output code M and W, LCD display may not be readable and
LCD display updates will be slower at temperatures below -22 °F
(-30 °C).
(2)
Wireless LCD display may not be readable and LCD display updates
will be slower at temperature below -4 °F (-20 °C).
(4)
Inert fill with traditional flange on Range 0: limits are 32 to 185°F
(0 to 85°C).
(5) 160 °F (71 °C) limit in vacuum service.
(6) Not available for 3051CA.
Humidity limits
Storage(1)
0–100% relative humidity
-50 to 230 °F (-46 to 110 °C)
With LCD display: -40 to 185 °F (-40 to 85 °C)
With Wireless Output: -40 °F to 185 °F (-40 °C to 85 °C)
Turn-on time
(1)
If storage temperature is above 85°C, perform a sensor trim prior to
installation.
Performance within specifications less than 2.0 seconds
(20.0 seconds for PROFIBUS PA and FOUNDATION fieldbus
protocols) after power is applied to the transmitter.(1)
(1)
Does not apply to wireless option code X.
Volumetric displacement
Less than 0.005 in3 (0,08 cm3)
www.rosemount.com
53
Rosemount 3051
Damping
4-20 mA HART
September 2014
For 3051CFC, see 00813-0100-4485 Rosemount 405 Compact
Orifice Plate
For 3051CFP, see 00813-0100-4485 Rosemount 1195 Integral
Orifice
Analog output response to a step input change is user-enterable
from 0.0 to 60 seconds for one time constant. This software
damping is in addition to sensor module response time.
Process-wetted parts
FOUNDATION fieldbus
Drain/vent valves
Transducer block: User configurable
AI Block: User configurable
316 SST, Alloy C-276, or Alloy 400 material (Alloy 400 not
available with 3051L)
PROFIBUS PA
Process flanges and adapters
AI Block only: User configurable
Physical specifications
Plated carbon steel
SST: CF-8M (Cast 316 SST) per ASTM A743
Cast C-276: CW-12MW per ASTM A494
Cast Alloy 400: M-30C per ASTM A494
Material selection
Wetted O-rings
Emerson provides a variety of Rosemount products with various
product options and configurations including materials of
construction that can be expected to perform well in a wide
range of applications. The Rosemount product information
presented is intended as a guide for the purchaser to make an
appropriate selection for the application. It is the purchaser’s
sole responsibility to make a careful analysis of all process
parameters (such as all chemical components, temperature,
pressure, flow rate, abrasives, contaminants, etc.), when
specifying product materials, options, and components for the
particular application. Emerson Process Management is not in a
position to evaluate or guarantee the compatibility of the
process fluid or other process parameters with the product
options, configuration, or materials of construction selected.
Glass-filled PTFE or Graphite-filled PTFE
Electrical connections
1
/2–14 NPT, G1/2, and M20 × 1.5 conduit. The polymer housing
(housing code P) has no conduit entries. HART interface
connections fixed to terminal block for output code A and to
701P Power Module for Output Code X.
Process connections
Rosemount 3051C
1
/4–18 NPT on 21/8-in. centers
1
/2–14 NPT on 2-, 21/8-, or 21/4-in. centers
Rosemount 3051L
High pressure side: 2-, 3-, or 4-in., ASME B 16.5 (ANSI) Class 150,
300 or 600 flange; 50, 80 or 100 mm, PN 40 or 10/16 flange
Low pressure side: 1/4–18 NPT on flange 1/2–14 NPT on adapter
Rosemount 3051T
3051CA
316L SST (UNS S31603)
Alloy C-276 (UNS N10276)
Alloy 400 (UNS N04400)
Tantalum (UNS R05440)
Gold-plated Alloy 400
Gold-plated 316L SST
3051T
Isolating diaphragm material
3051CD
3051CG
Process isolating diaphragms
•
•
•
•
•
•
•
•
•
•
•
•
•
Rosemount 3051L process wetted parts
Flanged process connection (transmitter high side)
Process diaphragms, including process gasket surface
316L SST, Alloy C-276, or Tantalum
Extension
CF-3M (Cast version of 316L SST, material per ASTM-A743),
or Alloy C-276. Fits schedule 40 and 80 pipe.
Mounting flange
Zinc-cobalt plated CS or SST
Reference process connection (transmitter low side)
Isolating diaphragms
316L SST or Alloy C-276
Reference flange and adapter
CF-8M (Cast version of 316 SST, material per ASTM-A743)
Non-wetted parts
1
/2–14 NPT female.
G1/2 A DIN 16288 Male (Range 1–4 only)
Autoclave type F-250-C (Pressure relieved 9/16–18 gland thread;
1
/4 OD high pressure tube 60° cone; available in SST for Range 5
transmitters only).
Electronics housing
Low-copper aluminum or CF-8M (Cast version of 316 SST).
Enclosure Type 4X, IP 65, IP 66, IP 68
Housing Material Code P: PBT/PC with NEMA 4X and IP66/67/68
Rosemount 3051CF
Coplanar sensor module housing
For 3051CFA, see 00813-0100-4485 Rosemount 485 Annubar
SST: CF-3M (Cast 316L SST)
54
www.rosemount.com
September 2014
Rosemount 3051
Table 12. 3051L Weights without Options
Bolts
Plated carbon steel per ASTM A449, Type 1
Austenitic 316 SST per ASTM F593
ASTM A193, Grade B7M alloy steel
Alloy K-500
Flange
DN 80/PN
40
DN 100/
PN 10/16
DN 100/
PN 40
Sensor module fill fluid
Coplanar: silicone or Inert Halocarbon
In-line: silicone or Fluorinert™ FC-43
Flush
lb. (kg)
2-in. Ext. 4-in. Ext. 6-in. Ext.
lb. (kg)
lb. (kg)
lb. (kg)
19.5 (8,8)
21.5 (9,7)
22.5
(10,2)
23.5
(10,6)
17.8 (8,1)
19.8 (9,0)
20.8 (9,5)
21.8 (9,9)
23.2
(10,5)
25.2
(11,5)
26.2
(11,9)
27.2
(12,3)
Process fill fluid (3051L only)
SYLTHERM XLT, D.C. Silicone 704, D.C. Silicone 200, inert,
glycerin and water, Neobee M-20, or propylene glycol and water
Paint
Polyurethane
Cover O-rings
Buna-N
Silicone (for wireless option code X)
Power module
Field replaceable, keyed connection eliminates the risk of
incorrect installation, Intrinsically Safe Lithium-thionyl chloride
Power Module with PBT enclosure.
Shipping weights
Table 11. Transmitter Weights without Options(1)
Transmitter
Rosemount 3051 In
Wireless In lb. (kg)
lb. (kg)
3051C
3051T
3051L
6.0 (2,7)
3.0 (1,4)
Table 12
3.9 (1,8)
1.9 (0,86)
Table 12
(1) Transmitter weights include the sensor module and housing only
(aluminum for Rosemount 3051 and polymer for wireless).
Table 12. 3051L Weights without Options
Flange
2-in., 150
3-in., 150
4-in., 150
2-in., 300
3-in., 300
4-in., 300
2-in., 600
3-in., 600
DN 50/PN
40
Flush
lb. (kg)
Add
lb. (kg)
Code
Option
J, K, L, M
J, K, L, M
M4/M5
M5
Stainless Steel Housing (T)
Stainless Steel Housing (C, L, H, P)
LCD display for wired transmitter
LCD Display for Wireless Output
SST Mounting Bracket for Coplanar
Flange
3.9 (1,8)
3.1 (1,4)
0.5 (0,2)
0.1 (0,04)
Mounting Bracket for Traditional Flange
2.3 (1,0)
Mounting Bracket for Traditional Flange
2.3 (1,0)
SST Bracket for Traditional Flange
Traditional Flange
Traditional Flange
Traditional Flange
Traditional Flange
Level Flange—3 in., 150
Level Flange—3 in., 300
Level Flange—2 in., 150
Level Flange—2 in., 300
DIN Level Flange, SST, DN 50, PN 40
DIN Level Flange, SST, DN 80, PN 40
SST Sensor Module
Power Module (701PGNKF)
2.3 (1,0)
2.4 (1,1)
2.7 (1,2)
2.6 (1,2)
2.5 (1,1)
10.8 (4,9)
14.3 (6,5)
10.7 (4,8)
14.0 (6,3)
8.3 (3,8)
13.7 (6,2)
1.0 (0,45)
0.4 (0,18)
B4
B1, B2,
B3
B7, B8,
B9
BA, BC
H2
H3
H4
H7
FC
FD
FA
FB
FP
FQ
WSM
1.0 (0,5)
2-in. Ext. 4-in. Ext. 6-in. Ext.
lb. (kg)
lb. (kg)
lb. (kg)
12.5 (5,7)
17.5 (7,9)
23.5
(10,7)
17.5 (7,9)
22.5
(10,2)
32.5
(14,7)
15.3 (6,9)
25.2
(11,4)
N/A
19.5 (8,8)
26.5
(12,0)
N/A
24.5
(11,1)
35.5
(16,1)
N/A
27.2
(12,3)
N/A
20.5 (9,3)
28.5
(12,9)
N/A
25.5
(11,6)
37.5
(17,0)
N/A
28.2
(12,8)
N/A
21.5 (9,7)
30.5
(13,8)
N/A
26.5
(12,0)
39.5
(17,9)
N/A
29.2
(13,2)
13.8 (6,2)
N/A
N/A
N/A
www.rosemount.com
Table 13. Transmitter Option Weights
55
Rosemount 3051
September 2014
3051 Product Certifications
European Directive Information
A copy of the EC Declaration of Conformity can be found at the
end of the Quick Start Guide. The most recent revision of the EC
Declaration of Conformity can be found at
www.rosemount.com.
Ordinary Location Certification for FM Approvals
As standard, the transmitter has been examined and tested to
determine that the design meets the basic electrical,
mechanical, and fire protection requirements by FM
Approvals, a nationally recognized test laboratory (NRTL) as
accredited by the Federal Occupational Safety and Health
Administration (OSHA).
Special Conditions for Safe Use (X):
1. The Model 3051 transmitter housing contains aluminum
and is considered a potential risk of ignition by impact or
friction. Care must be taken into account during
installation and use to prevent impact and friction.
2. The Model 3051 transmitter with the transient terminal
block (Option code T1) will not pass the 500Vrms
dielectric strength test and this must be taken into
account during installation.
C6
Standards: ANSI/ISA 12.27.01-2003, CSA Std. C22.2 No. 30
-M1986, CSA Std. C22.2 No.142-M1987, CSA
Std. C22.2. No.157-92, CSA Std. C22.2 No. 213
- M1987, CAN/CSA C22.2 No. 0-10, CSA Std
C22.2 No. 25-1966, CAN/CSA-C22.2 No.
94-M91, CAN/CSA-E60079-0-07,
CAN/CSA-E60079-1-07
North America
E5
FM Explosionproof (XP) and Dust-Ignitionproof (DIP)
Certificate: 0T2H0.AE
Standards: FM Class 3600 – 1998, FM Class 3615 – 2006,
FM Class 3810 – 2005, ANSI/NEMA 250 – 2003
Markings: Explosionproof for Class I, Division 1, Groups B,
C and D; Suitable for Class I, Zone 1, Group
IIB+H2, T5; Dust-Ignitionproof Class II, Division
1, Groups E, F, G; Class III Division 1; Intrinsically
Safe Class I, Division 1 Groups A, B, C, D when
connected in accordance with Rosemount
drawing 03031-1024, Temperature Code T3C;
Suitable for Class I, Zone 0; Class I Division 2
Groups A, B, C and D, T5; Suitable for Class I
Zone 2, Group IIC; Type 4X; Factory Sealed;
Single Seal (See drawing 03031-1053)
Markings: XP CL I, DIV 1, GP B, C, D; DIP CL II, DIV 1, GP E, F,
G; CL III; T5(-50°C  Ta  +85°C); Factory Sealed;
Type 4X
I5
FM Intrinsic Safety (IS) and Nonincendive (NI)
Certificate: 1Q4A4.AX
Standards: FM Class 3600 – 2011, FM Class 3610 – 2010,
FM Class 3611 – 2004, FM Class 3810 – 2005
Markings: IS CL I, DIV 1, GP A, B, C, D; CL II, DIV 1, GP E, F, G;
Class III; DIV 1 when connected per Rosemount
drawing 03031-1019; NI CL 1, DIV 2, GP A, B, C,
D; T4(-50°C  Ta  +70°C) [HART], T5(-50°C  Ta
 +40°C) [HART]; T4(-50°C  Ta  +60°C)
[Fieldbus/PROFIBUS]; Type 4x
Special Conditions for Safe Use (X):
1. The Model 3051 transmitter housing contains aluminum
and is considered a potential risk of ignition by impact or
friction. Care must be taken into account during
installation and use to prevent impact and friction.
2. The Model 3051 transmitter with the transient terminal
block (Option code T1) will not pass the 500Vrms
dielectric strength test and this must be taken into
account during installation.
IE
FM FISCO
Certificate: 1Q4A4.AX
CSA Explosionproof, Dust-Ignitionproof, Intrinsic Safety
and Nonincendive
Certificate: 1053834
E6
CSA Explosionproof, Dust-Ignitionproof and Division 2
Certificate: 1053834
Standards: ANSI/ISA 12.27.01-2003, CSA Std. C22.2 No. 30
-M1986, CSA Std. C22.2 No.142-M1987, CSA
Std. C22.2 No. 213 - M1987, CAN/CSA C22.2
No. 0-10, CSA Std C22.2 No. 25-1966,
CAN/CSA-C22.2 No. 94-M91, CAN/CSA-C22.2
No. 157-92, CAN/CSA-E60079-0-07,
CAN/CSA-E60079-1-07
Markings: Explosionproof Class I, Division 1, Groups B, C
and D; Suitable for Class I, Zone 1, Group
IIB+H2, T5; Dust-Ignitionproof for Class II and
Class III, Division 1, Groups E, F and G; Class I,
Division 2, Groups A, B, C and D; Suitable for
Class I Zone 2, Group IIC; Type 4X; Factory
Sealed; Single Seal (See drawing 03031-1053)
Standards: FM Class 3600 – 2011, FM Class 3610 – 2010,
FM Class 3611 – 2004, FM Class 3810 – 2005
Markings: IS CL I, DIV 1, GP A, B, C, D when connected per
Rosemount drawing 03031-1019 (-50°C  Ta 
+60°C); Type 4x
56
www.rosemount.com
September 2014
Rosemount 3051
Europe
E8
Special Conditions for Safe Use (X):
1. The apparatus is not capable of withstanding the 500 V
insulation test required by EN60079-11. This must be
taken into account when installing the apparatus.
ATEX Flameproof and Dust
Certificate: KEMA00ATEX2013X; Baseefa11ATEX0275X
2. The enclosure may be made of aluminum alloy and given a
protective polyurethane paint finish; however care should
be taken to protect it from impact or abrasion if located in
Zone 0.
Standards Used: EN60079-0:2012, EN60079-1:2007,
EN60079-26:2007, EN60079-31:2009
Markings: II 1/2 G, Ex d IIC T6/T5 Ga/Gb, T6(-50°C  Ta 
+65°C), T5(-50°C  Ta  +80°C);
II 1 D Ex ta IIIC T95°C T500 105°C Da (-20°C  Ta  +85°C)
3. Some variants of the equipment have reduced markings
on the nameplate. Refer to the Certificate for full
equipment marking.
Process Temperature
IA
Temperature class
Process temperature
T6
-50°C to +65°C
T5
-50°C to +80°C
ATEX FISCO
Certificate: BAS97ATEX1089X
Standards: EN60079-0:2012, EN60079-11:2009
Markings:
II 1 G Ex ia IIC Ga T4(-60°C  Ta  +60°C)
Special Conditions for Safe Use (X):
Input parameters
1. This device contains a thin wall diaphragm. Installation,
maintenance and use shall take into account the
environmental conditions to which the diaphragm will be
subjected. The manufacturer’s instructions for installation
and maintenance shall be followed in detail to assure
safety during its expected lifetime.
I1
FISCO
Voltage Ui
17.5 V
Current Ii
380 mA
2. For information on the dimensions of the flameproof joints
the manufacturer shall be contacted.
Power Pi
5.32 W
3. Some variants of the equipment have reduced markings
on the nameplate. Refer to the Certificate for full
equipment marking.
Capacitance Ci
ATEX Intrinsic Safety and Dust
Standards: EN60079-0:2012, EN60079-11:2012,
EN60079-31:2009
II 1 G Ex ia IIC T5/T4 Ga T5(-60°C  Ta 
+40°C), T4(-60°C  Ta  +70°C)
Fieldbus/PROFIBUS:
II 1 G Ex ia IIC Ga
T4(-60°C  Ta  +60°C)
DUST:
II 1 D Ex ta IIIC T95°C T500105°C Da
(-20°C  Ta  +85°C)
Input parameters
HART
Fieldbus/PROFIBUS
Voltage Ui
30 V
30 V
Current Ii
200 mA
300 mA
Power Pi
0.9 W
1.3 W
0.012 μF
0 μF
0 mH
0 mH
Capacitance Ci
Inductance Li
<10 μH
Special Conditions for Safe Use (X):
Certificate: BAS97ATEX1089X; Baseefa11ATEX0275X
Markings: HART:
Inductance Li
<5 nF
1. The apparatus is not capable of withstanding the 500 V
insulation test required by EN60079-11. This must be
taken into account when installing the apparatus.
2. The enclosure may be made of aluminum alloy and given a
protective polyurethane paint finish; however care should
be taken to protect it from impact or abrasion if located in
Zone 0.
N1
ATEX Type n and Dust
Certificate: BAS00ATEX3105X; Baseefa11ATEX0275X
Standards: EN60079-0:2012, EN60079-15:2010,
EN60079-31:2009
Markings:
II 3 G Ex nA IIC T5 Gc (-40°C  Ta  +70°C);
II 1 D Ex ta IIIC T95°C T500105°C Da (-20°C 
Ta  +85°C)
Special Conditions for Safe Use (X):
1. This apparatus is not capable of withstanding the 500V
insulation test that is required by EN60079-15. This must
be taken into account when installing the apparatus.
2. Some variants of the equipment have reduced markings
on the nameplate. Refer to the Certificate for full
equipment marking.
www.rosemount.com
57
Rosemount 3051
September 2014
International
E7
Special Conditions for Safe Use (X):
IECEx Flameproof and Dust
Certificate: IECEx KEM 09.0034X; IECEx BAS 10.0034X
Standards: IEC60079-0:2011, IEC60079-1:2007-04,
IEC60079-26:2006, IEC60079-31:2008
Markings: Ex d IIC T6/T5 Ga/Gb, T6(-50°C  Ta  +65°C),
T5(-50°C  Ta  +80°C);
Ex ta IIIC T95°C T500105°C Da (-20°C  Ta 
+85°C)
1. If the apparatus is fitted with an optional 90V transient
suppressor, it is not capable of withstanding the 500V
insulation test required by IEC 60079-11. This must be
taken into account when installing the apparatus.
2. The enclosure may be made of aluminum alloy and given a
protective polyurethane paint finish; however, care should
be taken to protect it from impact or abrasion if located in
Zone 0.
IECEx Mining (Special A0259)
Certificate: IECEx TSA 14.0001X
Process Temperature
Standards: IEC60079-0:2011, IEC60079-11:2011
Temperature class
Process temperature
T6
-50°C to +65°C
T5
-50°C to +80°C
Markings: Ex ia I Ma (-60°C  Ta  +70°C)
Input parameters
Special Conditions for Safe Use (X):
1. This device contains a thin wall diaphragm. Installation,
maintenance and use shall take into account the
environmental conditions to which the diaphragm will be
subjected. The manufacturer’s instructions for installation
and maintenance shall be followed in detail to assure
safety during its expected lifetime.
2. For information on the dimensions of the flameproof joints
the manufacturer shall be contacted.
3. Some variants of the equipment have reduced markings
on the nameplate. Refer to the Certificate for full
equipment marking.
I7
IECEx Intrinsic Safety
Certificate: IECEx BAS 09.0076X
Standards: IEC60079-0:2011, IEC60079-11:2011
Markings: HART: Ex ia IIC T5/T4 Ga, T5(-60°C  Ta  +40°C),
T4(-60°C  Ta  +70°C)
Fieldbus/PROFIBUS: Ex ia IIC Ga T4(-60°C  Ta 
+60°C)
Input parameters
HART
Fieldbus/PROFIBUS
Voltage Ui
30 V
30 V
Current Ii
200 mA
300 mA
Power Pi
0.9 W
1.3 W
0.012 μF
0 μF
0 mH
0 mH
Capacitance Ci
Inductance Li
58
HART
Fieldbus/PROFIBUS
FISCO
Voltage Ui
30 V
30 V
17.5 V
Current Ii
200 mA
300 mA
380 mA
Power Pi
0.9 W
1.3 W
5.32 W
0.012 μF
0 μF
<5 nF
0 mH
0 mH
<10 μH
Capacitance Ci
Inductance Li
Special Conditions for Safe Use (X):
1. If the apparatus is fitted with optional 90V transient
suppressor, it is not capable of withstanding the 500V
insulation test required by IEC60079-11. This must be
taken into account when installing the apparatus.
2. It is a condition of safe use that the above input
parameters shall be taken into account during installation.
3. It is a condition of manufacture that only the apparatus
fitted with housing, covers and sensor module housing
made out of stainless steel are used in Group I
applications.
N7
IECEx Type n
Certificate: IECEx BAS 09.0077X
Standards: IEC60079-0:2011, IEC60079-15:2010
Markings: Ex nA IIC T5 Gc (-40°C  Ta  +70°C)
Special Condition for Safe Use (X):
1. The apparatus is not capable of withstanding the 500V
insulation test required by IEC60079-15. This must be
taken into account when installing the apparatus.
www.rosemount.com
September 2014
Rosemount 3051
Brazil
Certificate: UL-BR 13.0584X
E2
INMETRO Flameproof
Standards: ABNT NBR IEC60079-0:2008 + Errata 1:2011,
ABNT NBR IEC60079-11:2009
Certificate: UL-BR 13.0643X
Markings: Ex ia IIC T4 Ga (-60°C  Ta  +60°C)
Standards: ABNT NBR IEC60079-0:2008 + Errata 1:2011,
ABNT NBR IEC60079-1:2009 + Errata 1:2011,
ABNT NBR IEC60079-26:2008 + Errata 1:2008
Input parameters
FISCO
Markings: Ex d IIC T6/T5 Ga/Gb, T6(-50°C  Ta  +65°C),
T5(-50°C  Ta  +80°C)
Special Conditions for Safe Use (X):
1. This device contains a thin wall diaphragm. Installation,
maintenance and use shall take into account the
environmental conditions to which the diaphragm will be
subjected. The manufacturer’s instructions for installation
and maintenance shall be followed in detail to assure
safety during its expected lifetime.
2. In case of repair, contact the manufacturer for information
on the dimensions of the flameproof joints.
3. The capacitance of the wrap around label, being 1.6nF,
exceeds the limit in Table 9 of ABNT NBR IEC 60079-0. The
user shall determine suitability for the specific application.
I2
INMETRO Intrinsic Safety
Certificate: UL-BR 13.0584X
Standards: ABNT NBR IEC60079-0:2008 + Errata 1:2011,
ABNT NBR IEC60079-11:2009
Markings: HART: Ex ia IIC T5/T4 Ga, T5(-60°C  Ta  +40°C),
T4(-60°C  Ta  +70°C)
Fieldbus/PROFIBUS: Ex ia IIC T4 Ga (-60°C  Ta 
+60°C)
Input parameters
HART
Fieldbus/PROFIBUS
Voltage Ui
30 V
30 V
Current Ii
200 mA
300 mA
Power Pi
0.9 W
1.3 W
0.012 μF
0 μF
0 mH
0 mH
Capacitance Ci
Inductance Li
Special Conditions for Safe Use (X):
1. If the equipment is fitted with an optional 90V transient
suppressor, it is not capable of withstanding the 500V
insulation test required by ABNT NBR IRC 60079-11:2008.
This must be taken into account when installing the
equipment.
2. The enclosure may be made of aluminum alloy and given a
protective polyurethane paint finish; however, care should
be taken to protect it from impact or abrasion if located in
Zone 0.
IB
INMETRO FISCO
www.rosemount.com
Voltage Ui
17.5 V
Current Ii
380 mA
Power Pi
5.32 W
Capacitance Ci
Inductance Li
<5 nF
<10 μH
Special Conditions for Safe Use (X):
1. If the equipment is fitted with an optional 90V transient
suppressor, it is not capable of withstanding the 500V
insulation test required by ABNT NBR IRC 60079-11:2008.
This must be taken into account when installing the
equipment.
2. The enclosure may be made of aluminum alloy and given a
protective polyurethane paint finish; however, care should
be taken to protect it from impact or abrasion if located in
Zone 0.
China
E3
China Flameproof
Certificate: GYJ14.1041X; GYJ10.1313X [Flowmeters]
Standards: GB3836.1-2000, GB3836.2-2010,
GB12476-2000
Markings: Ex d IIC T6/T5, T6(-50°C  Ta  +65°C), T5(-50°C 
Ta  +80°C)
Special Conditions for Safe Use (X):
1. The relation between ambient temperature arrange and
temperature class is as follows:
Ta
Temperature class
-50°C~+80°C
T5
-50°C~+65°C
T6
When used in a combustible dust environment, the
maximum ambient temperature is 80°C.
2. The earth connection facility in the enclosure should be
connected reliably.
3. Cable entry certified by notified body with type of
protection Ex d IIC in accordance with GB3836.1-2000 and
GB3836.2-2000, should be applied when installed in a
59
Rosemount 3051
September 2014
hazardous location. When used in combustible dust
environment, cable entry in accordance with IP66 or
higher level should be applied.
3. Intrinsically Safe parameters:
Input parameters
HART
Fieldbus/PROFIBUS
FISCO
Voltage Ui
30 V
30 V
17.5 V
Current Ii
200 mA
300 mA
380 mA
Power Pi
0.9 W
1.3 W
5.32 W
0.012 μF
0 μF
<5 nF
0 mH
0 mH
<10 μH
4. Obey the warning “Keep tight when the circuit is alive.”
5. End users are not permitted to change any internal
components.
6. During installation, use and maintenance of this product,
observe the following standards:
GB3836.13-1997 “Electrical apparatus for explosive gas
atmospheres Part 13: Repair and overhaul for apparatus
used in explosive gas atmospheres”
GB3836.15-2000 “Electrical apparatus for explosive gas
atmospheres Part 15: Electrical installations in hazardous
area (other than mines)”
GB3836.16-2006 “Electrical apparatus for explosive gas
atmospheres Part 16: Inspection and maintenance of
electrical installation (other than mines)”
GB50257-1996 “Code for construction and acceptance of
electric device for explosion atmospheres and fire hazard
electrical equipment installation engineering”.
GB12476.2-2006 “Electrical apparatus for use in the
presence of combustible dust Part 1-2: Electrical apparatus
protected by enclosures and surface temperature
limitation-Selection, installation and maintenance”
GB15577-2007 “Safety regulations for dust explosion
prevention and protection”
I3
China Intrinsic Safety
Certificate: GYJ13.1362X; GYJ101312X [Flowmeters]
Standards: GB3836.1-2010, GB3836.4-2010,
GB3836.20-2010, GB12476.1-2000
Markings: Ex ia IIC Ga T4/T5
Special Conditions for Safe Use (X):
1. Symbol “X” is used to denote specific conditions of use:
a.If the apparatus is fitted with an optional 90V transient
suppressor, it is not capable of withstanding the 500V
insulation test for 1 minute. This must be taken into
account when installing the apparatus.
b.The enclosure may be made of aluminum alloy and
given a protective polyurethane paint finish; however,
care should be taken to protect it from impact or
abrasion if located in Zone 0.
2. The relation between T code and ambient temperature
range is:
60
Model
T
code
Temperature
range
HART
T5
-60°C  Ta  +40°C
HART
T4
-60°C  Ta  +70°C
Fieldbus/PROFIBUS/FISCO
T4
-60°C  Ta  +60°C
Flowmeter with 644 Temp
Housing
T4
-40°C  Ta  +60°C
Capacitance Ci
Inductance Li
Note 1: FISCO parameters apply to both Group IIC and IIB.
Note 2: [For Flowmeters] When 644 Temperature
Transmitter is used, it should be used with Ex-certified
associated apparatus to establish explosion protection
system that can be used in explosive gas atmospheres.
Wiring and terminals should comply with the instruction
manual of both 644 Temperature Transmitter and
associated apparatus. The cables between 644
Temperatures Transmitter and associated apparatus
should be shielded cables (the cables must have insulated
shield). The shielded cable has to be grounded reliably in a
non-hazardous area.
4. Transmitters comply with the requirements for FISCO field
devices specified in IEC60079-27:2008. For the connection
of an intrinsically safe circuit in accordance with FISCO
Model, FISCO parameters are listed in the table above.
5. The product should be used with Ex-certified associated
apparatus to establish explosion protection system that
can be used in explosive gas atmospheres. Wiring and
terminals should comply with the instruction manual of
the product and associated apparatus.
6. The cables between this product and associated apparatus
should be shielded cables (the cables must have insulated
shield). The shielded cable has to be grounded reliably in a
non-hazardous area.
7. End users are not permitted to change any intern
components but to settle the problem in conjunction with
the manufacturer to avoid damage to the product.
8. During installation, use and maintenance of this product,
observe the following standards:
GB3836.13-1997 “Electrical apparatus for explosive gas
atmospheres Part 13: Repair and overhaul for apparatus
used in explosive gas atmospheres”
GB3836.15-2000 “Electrical apparatus for explosive gas
atmospheres Part 15: Electrical installations in hazardous
area (other than mines)”
GB3836.16-2006 “Electrical apparatus for explosive gas
atmospheres Part 16: Inspection and maintenance of
electrical installation (other than mines)”
GB50257-1996 “Code for construction and acceptance of
electric device for explosion atmospheres and fire hazard
electrical equipment installation engineering”.
GB12476.2-2006 “Electrical apparatus for use in the
presence of combustible dust Part 1-2: Electrical apparatus
protected by enclosures and surface temperature
www.rosemount.com
September 2014
N3
Rosemount 3051
limitation-Selection, installation and maintenance”
GB15577-2007 “Safety regulations for dust explosion
prevention and protection”
Technical Regulations Customs Union
(EAC)
China Type n
EM, IM, KM
Certificate: GYJ101111X
Standards: GB3836.1-2000, GB3836.8-2003
Markings: Ex nA IIC T5 (-40°C  Ta  +70°C)
Special Conditions for Safe Use (X):
1. Symbol “X” is used to denote specific conditions of use:
The apparatus is not capable of withstanding the 500V test
to earth for one minute. The must be taken into
consideration during installation.
2. The ambient temperature range is -40°C  Ta  +70°C.
3. Maximum input voltage: 55V.
4. Cable glands, conduit or blanking plugs, certified by NEPSI
with Ex e or Ex n protection type and IP66 degree of
protection provided by enclosure, should be used on
external connections and redundant cable entries.
5. Maintenance should be done in non-hazardous location.
6. End users are not permitted to change any internal
components but to settle the problem in conjunction with
manufacturer to avoid damage to the product.
7. During installation, use and maintenance of this product,
observe the following standards:
GB3836.13-1997 “Electrical apparatus for explosive gas
atmospheres Part 13: Repair and overhaul for apparatus
used in explosive gas atmospheres”
GB3836.15-2000 “Electrical apparatus for explosive gas
atmospheres Part 15: Electrical installations in hazardous
area (other than mines)”
GB3836.16-2006 “Electrical apparatus for explosive gas
atmospheres Part 16: Inspection and maintenance of
electrical installation (other than mines)”
GB50257-1996 “Code for construction and acceptance of
electric device for explosion atmospheres and fire hazard
electrical equipment installation engineering”
Japan
E4
Japan Flameproof
Certificate: TC20577, TC20578, TC20583, TC20584
[HART]; TC20579, TC20580, TC20581,
TC20582 [Fieldbus]
Contact an Emerson Process Management
representative for further information.
Combinations
K2
Combination of E2 and I2
K5
Combination of E5 and I5
K6
Combination of C6, E8, and I1
K7
Combination of E7, I7, and N7
K8
combination of E8, I1, and N1
KB
Combination of E5, I5, and C6
KD
Combination of E8, I1, E5, I5, and C6
Conduit Plugs and Adapters
IECEx Flameproof and Increased Safety
Certificate: IECEx FMG 13.0032X
Standards: IEC60079-0:2011, IEC60079-1:2007,
IEC60079-7:2006-2007
Markings: Ex de IIC Gb
ATEX Flameproof and Increased Safety
Certificate: FM13ATEX0076X
Standards: EN60079-0:2012, EN60079-1:2007,
IEC60079-7:2007
Markings:
II 2 G Ex de IIC Gb
Conduit Plug Thread Sizes
Thread
Identification mark
M20 x 1.5
M20
1/2 - 14 NPT
1/2 NPT
G1/2A
G1/2
Markings: Ex d IIC T5
www.rosemount.com
61
Rosemount 3051
September 2014
Application:
Thread Adapter Thread Sizes
Male thread
Identification mark
M20 x 1.5 – 6H
M20
1/2 - 14 NPT
1/2 – 14 NPT
3/4 - 14 NPT
3/4 – 14 NPT
Female thread
Identification mark
M20 x 1.5 – 6H
M20
1/2 - 14 NPT
1/2 – 14 NPT
PG 13.5
PG 13.5
Location classes
2. The blanking plug shall not be used with an adapter.
3. Blanking Plug and Threaded Adapter shall be either NPT or
Metric thread forms. G½ and PG 13.5 thread forms are
only acceptable for existing (legacy) equipment
installations.
3051
Temperature
D
Humidity
B
Vibration
A
EMC
B
Enclosure
D
SLL Lloyds Register (LR) Type Approval
Certificate: 11/60002
Special Conditions for Safe Use (X):
1. When the thread adapter or blanking plug is used with an
enclosure in type of protection increased safety “e” the
entry thread shall be suitably sealed in order to maintain
the ingress protection rating (IP) of the enclosure.
Type
Application: Environmental categories ENV1, ENV2, ENV3
and ENV5
C5
Custody Transfer - Measurement Canada Accuracy
Approval
Certificate: AG-0226; AG-0454; AG-0477
IEC 62591 (WirelessHART Protocol)
Additional Certifications
Approved Manufacturing Locations
SBS American Bureau of Shipping (ABS) Type Approval
Rosemount Inc. — Chanhassen, Minnesota USA
Fisher-Rosemount GmbH & Co. — Wessling, Germany
Emerson Process Management Asia Pacific Private Limited —
Singapore
Beijing Rosemount Far East Instrument Co., LTD — Beijing, China
Certificate: 09-HS446883A-PDA
Intended Use: Measure gauge or absolute pressure of
liquid, gas or vapor applications on ABS classed
vessels, marine, and offshore installations.
ABS Rules: 2014 Steel Vessels Rules 1-1-4/7.7, 4-8-3/13.1,
1-1-A3, 4-8-3/1.7, 4-8-3/1.11.1
SBV Bureau Veritas (BV) Type Approval
European Directive Information
The most recent revision of the EC declaration of conformity can
be found at www.rosemount.com.
Certificate: 23155/A3 BV
Telecommunication Compliance
Requirements: Bureau Veritas Rules for the Classification of
Steel Ships
All wireless devices require certification to ensure that they
adhere to regulations regarding the use of the RF spectrum.
Nearly every country requires this type of product certification.
Emerson is working with governmental agencies around the
world to supply fully compliant products and remove the risk of
violating country directives or laws governing wireless device
usage.
Application: Class notations: AUT-UMS, AUT-CCS,
AUT-PORT and AUT-IMS; Pressure transmitter
type 3051 cannot be installed on diesel engines
SDN Det Norske Veritas (DNV) Type Approval
Certificate: A-13245
Intended Use: Det Norske Veritas’ Rules for Classification of
Ships, High Speed & Light Craft and Det Norske
Veritas’ Offshore Standards
62
www.rosemount.com
September 2014
Rosemount 3051
FCC and IC
CSA - Canadian Standards Association
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following conditions: This device may not cause
harmful interference. This device must accept any interference
received, including interference that may cause undesired
operation. This device must be installed to ensure a minimum
antenna separation distance of 20 cm from all persons.
I6
Ordinary Location Certification for FM
As standard, the transmitter has been examined and tested to
determine that the design meets basic electrical, mechanical,
and fire protection requirements by FM, a nationally recognized
testing laboratory (NRTL) as accredited by the Federal
Occupational Safety and Health Administration (OSHA).
European Certifications
I1
North American Certifications
Factory Mutual (FM) approvals
I5
FM Intrinsically Safe
Certificate No: 3046325
Applicable Standards: Class 3600:2011, Class 3610:2010,
Class 3810: 2005, ANSI/ISA 60079-0 2009,ANSI/ISA
60079-11:2009&#10;ANSI/NEMA 250:2003, ANSI/IEC
60529:2004
Markings: Intrinsically Safe for Class I, Division I, Groups A,
B, C, D
Zone Marking: Class I Zone 0, AEx ia IIC
T4 (-40 °C to 70 °C)
Intrinsically Safe when installed according to Rosemount
Drawing 03031-1062
Enclosure Type 4X/IP66/IP68/IP67
CSA Intrinsically Safe
Certificate No: 2526009
Applicable Standards: CSA C22.2 No. 0-M91, CSA C22.2
No. 94-M91, CSA C22.2 No. 142-M1987, CSA C22.2 No.
157-92, CSA C22.2 No. 60529-05
Markings: Intrinsically Safe For Class I, Division I, Groups A,
B, C, D
T4 (-40 °C to 70 °C)
Intrinsically safe when installed according to Rosemount
drawing 03031-1063
Enclosure Type 4X/IP66/IP68
ATEX Intrinsic Safety
Certificate No: Baseefa12ATEX0228X
Applicable Standards: EN60079-11:2012,
EN60079-0:2012
Markings: Ex ia IIC T4 Ga (-40 °C Ta 70 °C)
II 1G
IP66/68
1180
Special Conditions for Safe Use (X):
1. The plastic enclosure may constitute a potential
electrostatic ignition risk and must not be rubbed or
cleaned with a dry cloth.
I7
IECEx Intrinsic Safety
Certificate No: IECEx BAS 12.0124X
Applicable Standards: IEC60079-11:2011,
IEC60079-0:2011
Markings: Ex ia IIC T4 Ga (-40 °C Ta 70 °C)
IP66/68
Special Conditions for Safe Use (X):
1. The inline pressure sensor may contain more than 10%
aluminum and is considered a potential risk of ignition by
impact or friction. Care must be taken into account during
installation and use to prevent impact and friction.
2. The surface resistivity of the transmitter is greater than
one gigaohm. To avoid electrostatic charge build-up, it
must not be rubbed or cleaned with solvents or a dry cloth.
3. The Model 3051 Wireless Pressure Transmitter shall only
be used with the 701PGNKF Rosemount SmartPower
Battery Pack.
www.rosemount.com
Special Conditions for Safe Use (X):
1. The plastic enclosure may constitute a potential
electrostatic ignition risk and must not be rubbed or
cleaned with a dry cloth.
2. The Model 701PGNKF Power Module may be replaced in a
hazardous area. The Power Module has a surface resistivity
greater than 1G  and must be properly installed in the
wireless device enclosure. Care must be taken during
transportation to and from the point of installation to
prevent electrostatic charge build-up.
63
Rosemount 3051
September 2014
Pipe I.D. Range Codes
For pipes with an Inner Diameter (I.D.) Range/Pipe Wall Thickness not found in this table or with a line size greater than 12-in. (300
mm), choose option code Z and specify the exact pipe dimensions (I.D. and Pipe Wall Thickness) on the Configuration Data Sheet
(see document number 00806-0100-4010). The Emerson Process Management sizing program will determine this code, based on
the application piping.
Line size
Nominal
2-in.
(50 mm)
21/2-in.
(63.5 mm)
3-in.
(80 mm)
31/2-in.
(89 mm)
4-in.
(100 mm)
5-in.
(125 mm)
64
Max. O.D.
2.625-in.
(66.68 mm)
3.188-in.
(80.98 mm)
3.75-in.
(95.25 mm)
4.25-in.
(107.95 mm)
5.032-in.
(127.81 mm)
6.094-in.
(154.79 mm)
Pipe wall thickness
Option I.D. range
code
020
025
030
035
040
050
1.784 to 1.841-in.
(45.31 to 46.76 mm)
1.842 to 1.938-in.
(46.79 to 49.23 mm)
1.939 to 2.067-in.
(49.25 to 52.50 mm)
2.068 to 2.206-in.
(52.53 to 56.03 mm)
2.207 to 2.322-in.
(56.06 to 58.98 mm)
2.323 to 2.469-in.
(59.00 to 62.71 mm)
2.470 to 2.598-in.
(62.74 to 65.99 mm)
2.599 to 2.647-in.
(66.01 to 67.23 mm)
2.648 to 2.751-in.
(67.26 to 69.88 mm)
2.752 to 2.899-in.
(69.90 to 73.63 mm)
2.900 to 3.068-in.
(73.66 to 77.93 mm)
3.069 to 3.228-in.
(77.95 to 81.99 mm)
3.229 to 3.333-in.
(82.02 to 84.66 mm)
3.334 to 3.548-in.
(84.68 to 90.12 mm)
3.549 to 3.734-in.
(90.14 to 94.84 mm)
3.735 to 3.825-in.
(94.87 to 97.16 mm)
3.826 to 4.026-in.
(97.18 to 102.26 mm)
4.027 to 4.237-in.
(102.29 to 107.62 mm)
4.238 to 4.437-in.
(107.65 to 112.70 mm)
4.438 to 4.571-in.
(112.73 to 116.10 mm)
4.572 to 4.812-in.
(116.13 to 122.22 mm)
4.813 to 5.047-in.
(122.25 to 128.19 mm)
5.048 to 5.249-in.
(128.22 to 133.32 mm)
ANSI pipes
0.065 to 0.545-in.
(1.7 to 13.8 mm)
0.083 to 0.563-in.
(2.1 to 14.3 mm)
0.083 to 0.563-in.
(2.1 to 14.3 mm)
0.120 to 0.600-in.
(3.0 to 15.2 mm)
0.120 to 0.600-in.
(3.0 to 15.2 mm)
0.134 to 0.614-in.
(3.4 to 15.6 mm)
Non-ANSI pipes
0.065 to 0.488-in.
(1.7 to 12.4 mm)
0.065 to 0.449-in.
(1.7 to 11.4 mm)
0.065 to 0.417-in.
(1.7 to 10.6 mm)
0.065 to 0.407-in.
(1.7 to 10.3 mm)
0.083 to 0.448-in.
(2.1 to 11.4 mm)
0.083 to 0.417-in.
(2.1 to 10.6 mm)
0.083 to 0.435-in.
(2.1 to 11.0 mm)
0.083 to 0.515-in.
(2.1 to 13.1 mm)
0.083 to 0.460-in.
(2.1 to 11.7 mm)
0.083 to 0.416-in.
(2.1 to 10.6 mm)
0.083 to 0.395-in.
(2.1 to 10.0 mm)
0.083 to 0.404-in
(2.1 to 10.3 mm)
0.120 to 0.496-in.
(3.0 to 12.6 mm)
0.120 to 0.386-in.
(3.0 to 9.8 mm)
0.120 to 0.415-in.
(3.0 to 10.5 mm)
0.120 to 0.510-in.
(3.0 to 13.0 mm)
0.120 to 0.400-in.
(3.0 to 10.2 mm)
0.120 to 0.390-in.
(3.0 to 9.9 mm)
0.120 to 0.401-in.
(3.0 to 10.2 mm)
0.134 to 0.481-in.
(3.4 to 12.2 mm)
0.134 to 0.374-in.
(3.4 to 9.5 mm)
0.134 to 0.380-in.
(3.4 to 9.7 mm)
0.134 to 0.413-in.
(3.4 to 10.5 mm)
I.D.
range
code
A
B
C
D
B
C
D
E
A
B
C
D
B
C
D
B
C
D
E
A
B
C
D
www.rosemount.com
Sensor
Size 2
Sensor
Size 1
Sensor
Z2
Sensor
Size 1
Sensor
Size 2
Sensor
Size 1
September 2014
6-in.
(150 mm)
6-in.
(150 mm)
7-in.
(180 mm)
7-in.
(180 mm)
8-in.
(200 mm)
8-in.
(200 mm)
10-in.
(250 mm)
12-in.
(300 mm)
Rosemount 3051
6.93-in.
(176.02 mm)
6.93-in.
(176.02 mm)
7.93-in.
(201.42 mm)
7.93-in.
(201.42 mm)
9.688-in.
(246.08 mm)
9.688-in.
(246.08 mm)
11.75-in.
(298.45 mm)
13.0375-in.
(331.15 mm)
www.rosemount.com
060
060
070
070
080
080
100
120
5.250 to 5.472-in.
(133.35 to 138.99 mm)
5.473 to 5.760-in.
(139.01 to 146.30 mm)
5.761 to 6.065-in.
(146.33 to 154.05 mm)
6.066 to 6.383-in.
(154.08 to 162.13 mm)
5.250 to 5.472-in.
(133.35 to 139.99 mm)
5.473 to 5.760-in.
(139.01 to 146.30 mm)
5.761 to 6.065-in.
(146.33 to 154.05 mm)
6.066 to 6.383-in.
(154.08 to 162.13 mm)
6.384 to 6.624-in.
(162.15 to 168.25 mm)
6.625 to 7.023-in.
(168.28 to 178.38 mm)
7.024 to 7.392-in.
(178.41 to 187.76 mm)
6.384 to 6.624-in.
(162.15 to 168.25 mm)
6.625 to 7.023-in.
(168.28 to 178.38 mm)
7.024 to 7.392-in.
(178.41 to 187.76 mm)
7.393 to 7.624-in.
(187.78 to 193.65 mm)
7.625 to 7.981-in.
(193.68 to 202.72 mm)
7.982 to 8.400-in.
(202.74 to 213.36 mm)
8.401 to 8.766-in.
(213.39 to 222.66 mm)
7.393 to 7.624-in.
(187.78 to 193.65 mm)
7.625 to 7.981-in.
(193.68 to 202.72 mm)
7.982 to 8.400-in.
(202.74 to 213.36 mm)
8.401 to 8.766-in.
(213.39 to 222.66 mm)
8.767 to 9.172-in.
(222.68 to 232.97 mm)
9.173 to 9.561-in.
(232.99 to 242.85 mm)
9.562 to 10.020-in.
(242.87 to 254.51 mm)
10.021 to 10.546-in.
(254.53 to 267.87 mm)
10.547 to 10.999-in.
(267.89 to 279.37 mm)
11.000 to 11.373-in.
(279.40 to 288.87 mm)
11.374 to 11.938-in.
(288.90 to 303.23 mm)
11.939 to 12.250-in.
(303.25 to 311.15 mm)
0.134 to 0.614-in.
(3.4 to 15.6 mm)
0.134 to 1.354-in.
(3.4 to 34.4 mm)
0.134 to 0.614-in.
(3.4 to 15.6 mm)
0.134 to 1.354-in.
(3.4 to 34.4 mm)
0.250 to 0.73-in.
(6.4 to 18.5 mm)
0.250 to 1.47-in.
(6.4 to 37.3 mm)
0.250 to 1.470-in.
(6.4 to 37.3 mm)
0.250 to 1.470-in.
(6.4 to 37.3 mm)
0.134 to 0.3919-in.
(3.4 to 9.9 mm)
0.134 to 0.327-in.
(3.4 to 8.3 mm)
0.134 to 0.31-in.
(3.4 to 7.9 mm)
0.134 to 0.297-in.
(3.4 to 7.5 mm)
0.134 to 1.132-in.
(3.4 to 28.7 mm)
0.134 to 1.067-in.
(3.4 to 27.1 mm)
0.134 to 1.05-in.
(3.4 to 26.7 mm)
0.134 to 1.037-in.
(3.4 to 26.3 mm)
0.134 to 0.374-in.
(3.4 to 9.5 mm)
0.134 to 0.216-in.
(3.4 to 5.5 mm)
0.134 to 0.246-in.
(3.4 to 6.2 mm)
0.134 to 1.114-in.
(3.4 to 28.3 mm)
0.134 to 0.956-in.
(3.4 to 24.3 mm)
0.134 to 0.986-in.
(3.4 to 25.0 mm)
0.250 to 0.499-in.
(6.4 to 12.6 mm)
0.250 to 0.374-in.
(6.4 to 9.5 mm)
0.250 to 0.312-in.
(6.4 to 7.9 mm)
0.250 to 0.364-in.
(6.4 to 9.2 mm)
0.250 to 1.239-in.
(6.4 to 31.4 mm)
0.250 to 1.114-in.
(6.4 to 28.3 mm)
0.250 to 1.052-in.
(6.4 to 26.7 mm)
0.250 to 1.104-in.
(6.4 to 28.0 mm)
0.250 to 1.065-in.
(6.4 to 27.1 mm)
0.250 to 1.082-in.
(6.4 to 27.5 mm)
0.250 to 1.012-in.
(6.4 to 25.7 mm)
0.250 to 0.945-in.
(6.4 to 24.0 mm)
0.250 to 1.018-in.
(6.4 to 25.9 mm)
0.250 to 1.097-in.
(6.4 to 27.9 mm)
0.250 to 0.906-in.
(6.4 to 23.0 mm)
0.250 to 1.159-in.
(6.4 to 29.4 mm)
A
B
C
D
A
B
C
D
B
C
D
B
C
D
B
C
D
E
B
C
D
E
A
B
C
D
E
B
C
D
65
Rosemount 3051
September 2014
Rosemount 3051 Dimensional Drawings(1)
Figure 1. Rosemount 3051C Exploded View
F
E
D
C
B
A
G
H
I
J
K
N
L
O
M
P
Q
A. Cover
B. Cover O-ring
C. Terminal Block
D. Electronics Housing
E. Configuration Buttons Cover
F. Local Configuration Buttons
(1)
66
G. Electronics Board
H. Name Plate
I. Housing Rotation Set Screw (180 degree maximum
rotation without further disassembly)
J. Sensor Module
K. Coplanar Flange
L. Drain/Vent Valve
M. Flange Adapters
N. Process O-Ring
O. Flange Adapter O-Ring
P. Flange Alignment Screw (not pressure retaining)
Q. Flange Bolts
This section contains dimensional drawings for output codes A, F and X. For output codes W and M, visit
http://www2.emersonprocess.com/en-US/brands/rosemount/Documentation-and-Drawings/Type-1-Drawings/Pages/index.aspx
www.rosemount.com
September 2014
Rosemount 3051
Figure 2. Rosemount 3051C Coplanar Flange
4.29
(109)
4.09
(104)
7.12
(181)
6.55
(166)
Dimensions are in inches (millimeters).
Figure 3. 3051 Wireless Housing with Coplanar Flange
4.196
(106.6)
5.49
(139)
7.41
(188)
Dimensions are in inches (millimeters).
www.rosemount.com
67
Rosemount 3051
September 2014
Figure 4. Rosemount 3051C Coplanar Flange with Rosemount 305RC3 3-Valve Coplanar Integral Manifold
6.75
(171)
5.50 (140)
Max Open
9.20 (234)
Max Open
Dimensions are in inches (millimeters).
68
www.rosemount.com
September 2014
Rosemount 3051
Figure 5. Coplanar Flange Mounting Configurations with Optional Bracket (B4) for 2-in. Pipe or Panel Mounting
A
2.81
(71)
B
PANEL
MOUNTING
3.35
(85)
6.20
(157)
2.81
(71)
4.73
(120)
C
D
PIPE
MOUNTING
3.35
(85)
6.25
(159)
3.50
(89)
A. 5/16 - 18 Bolts (not supplied)
B. 3/8–16 Bolts
Dimensions are in inches (millimeters).
www.rosemount.com
C. 2-inch U-Bolt
D. 3/8–16 Bolts
69
Rosemount 3051
September 2014
Figure 6. Rosemount 3051C Coplanar with Traditional Flange
4.09
(104)
1.63
(41)
2.13
(54)
A
1.16
(29)
3.40
(86)
1.10
(28)
A. Flange Adapters (optional)
Dimensions are in inches (millimeters).
Figure 7. Rosemount 3051C Coplanar with Rosemount 305RT3 3-Valve Traditional Integral Manifold
6.28
(159)
A
3.63
(92)
0.91
(23)
3.50
(89)
1.10
(28)
6.38
(162)
2.13
(54)
2.52
(64)
A. 1/2–14 NPT Flange Adapter (optional)
Dimensions are in inches (millimeters).
70
www.rosemount.com
September 2014
Rosemount 3051
Figure 8. Traditional Flange Moun
Open as PDF
Similar pages
Rosemount 3051 Pressure Transmitter Product Data Sheet
Transmetteurs de pression Rosemount 3051 et débitmètres Rosemount série 3051CF
Quick Start Guide: Rosemount 3051 with 4-20mA and 1
Quick start Guide: Rosemount 3051 with 4
Rosemount 3051 Pressure Transmitter Rosemount 3051CF Series Flowmeter Transmitter
Rosemount 1195 Integral Orifice Flow Meter Data Sheet
Rosemount 3051 Pressure Transmitter and Rosemount 3051CF DP Flowmeters Wireless Protocol
دریافت کاتالوگ Rosemount 3051
Rosemount 3051 Pressure Transmitter Product Data Sheet
Rosemount 485 Annubar Flange
Rosemount 3051L Liquid Level Transmitter Datasheet
Trasmettitore di pressione 3051 Rosemount e misuratori di portata serie 3051CF Rosemount
Rosemount 3051 Revision 5 Pressure Transmitter Rosemount 3051 Product Data Sheet
Transmissor de Pressão Rosemount 3051 e Medidores de Vazão Rosemount Série 3051CF
Rosemount 3051 Druckmessumformermit FOUNDATION™ Feldbus
Transmissor de pressão Rosemount 3051 Rosemount 3051 Folha de dados do produto
Appendix A Reference Data Annubar Flowmeter Series Reference Manual
Transmetteur de pression Rosemount Modèle 3051 Rosemount 3051 Fiche de spécification
Rosemount 485 Annubar Threaded Assembly
Transmissor de Pressão Rosemount 2051 Transmissor de Caudalímetro Série Rosemount 2051CF
Rosemount Druckmessumformer 3051
Material Selection and Compatibility Considerations for Rosemount Pressure Transmitters ®