Yamaha YSP-800 Owner`s manual

YSP-800_UB-cv.fm Page 1 Monday, July 25, 2005 11:15 AM
UB
YSP-800
Digital Sound Projector
This product mainly uses lead-free solder.
© 2005
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
All rights reserved.
OWNER’S MANUAL
Printed in Malaysia
WF72220
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
■ Explanation of Graphical Symbols
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert you to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral
triangle is intended to alert you to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
1
Read these instructions.
2
Keep these instructions.
3
Heed all warnings.
4
Follow all instructions.
5
Do not use this apparatus near water.
6
Clean only with dry cloth.
7
Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
8
Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers)
that produce heat.
9
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10 Protect the power cable from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11 Only use attachments/accessories specified by the
manufacturer.
12 Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
13 Unplug this apparatus during lightning storms or when
unused for long periods of time.
14 Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
i
IMPORTANT SAFETY INSTRUCTIONS
FCC INFORMATION (for US customers)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the instructions
contained in this manual, meets FCC requirements.
Modifications not expressly approved by YAMAHA may
void your authority, granted by the FCC, to use the product.
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this product
is found to be the source of interference, which can be
determined by turning the unit “OFF” and “ON”, please try
to eliminate the problem by using one of the following
measures:
2. IMPORTANT:
When connecting this product to accessories and/or another
product use only high quality shielded cables. Cable/s
supplied with this product MUST be used. Follow all
installation instructions. Failure to follow instructions could
void your FCC authorization to use this product in the USA.
Relocate either this product or the device that is being
affected by the interference.
3. NOTE:
This product has been tested and found to comply with the
requirements listed in FCC Regulations, Part 15 for Class
“B” digital devices. Compliance with these requirements
provides a reasonable level of assurance that your use of
this product in a residential environment will not result in
harmful interference with other electronic devices.
This equipment generates/uses radio frequencies and, if not
installed and used according to the instructions found in the
users manual, may cause interference harmful to the
operation of other electronic devices.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact YAMAHA Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by YAMAHA Corporation of America or its
subsidiaries.
We Want You Listening For A Lifetime
YAMAHA and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of
your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying
blaring or distortion – and, most importantly, without affecting your sensitive hearing.
Since hearing damage from loud sounds is often undetectable until it is too late, YAMAHA and the Electronic Industries
Association’s Consumer Electronics Group recommend you to avoid prolonged exposure from excessive volume levels.
ii
CAUTION: READ THIS BEFORE OPERATING THIS UNIT.
CAUTION: READ THIS BEFORE OPERATING THIS UNIT.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
iii
To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
Install this sound system in a well ventilated, cool, dry, clean
place with at least 5 cm of space above (or below) this unit –
away from direct sunlight, heat sources, vibration, dust, moisture,
and/or cold.
Locate this unit away from other electrical appliances, motors, or
transformers to avoid humming sounds.
Do not expose this unit to sudden temperature changes from cold
to hot, and do not locate this unit in an environment with high
humidity (i.e. a room with a humidifier) to prevent condensation
inside this unit, which may cause an electrical shock, fire,
damage to this unit, and/or personal injury.
Avoid installing this unit where foreign object may fall onto this
unit and/or this unit may be exposed to liquid dripping or
splashing. On the top of this unit, do not place:
– Other components, as they may cause damage and/or
discoloration on the surface of this unit.
– Burning objects (i.e. candles), as they may cause fire, damage
to this unit, and/or personal injury.
– Containers with liquid in them, as they may fall and liquid
may cause electrical shock to the user and/or damage to this
unit.
Do not cover this unit with a newspaper, tablecloth, curtain, etc.
in order not to obstruct heat radiation. If the temperature inside
this unit rises, it may cause fire, damage to this unit, and/or
personal injury.
Do not plug in this unit to a wall outlet until all connections are
complete.
Do not operate this unit upside-down. It may overheat, possibly
causing damage.
Do not use force on switches, knobs and/or cords.
When disconnecting the power cable from the wall outlet, grasp
the plug; do not pull the cable.
Do not clean this unit with chemical solvents; this might damage
the finish. Use a clean, dry cloth.
Only voltage specified on this unit must be used. Using this unit
with a higher voltage than specified is dangerous and may cause
fire, damage to this unit, and/or personal injury. YAMAHA will
not be held responsible for any damage resulting from use of this
unit with a voltage other than specified.
Do not attempt to modify or fix this unit. Contact qualified
YAMAHA service personnel when any service is needed.
The cabinet should never be opened for any reasons.
When not planning to use this unit for long periods of time (i.e.
vacation), disconnect the AC power plug from the wall outlet.
Be sure to read the “TROUBLESHOOTING” section on
common operating errors before concluding that this unit is
faulty.
Before moving this unit, press STANDBY/ON to set this unit in
standby mode, and disconnect the AC power plug from the wall
outlet.
Condensation will form when the surrounding temperature
changes suddenly. Disconnect the power cable from the outlet,
then leave the unit alone.
When using the unit for a long time, the unit may become warm.
Turn the power off, then leave the unit alone for cooling.
Install this unit near the AC outlet and where the AC power plug
can be reached easily.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
This unit is not disconnected from the AC power source as
long as it is connected to the AC wall outlet, even if this unit
itself is turned off. This state is called the standby mode. In
this state, this unit is designed to consume a very small
quantity of power.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to wide
slot and fully insert.
This Class B digital apparatus complies with Canadian ICES003.
IMPORTANT
Please record the serial number of this unit in the space below.
MODEL:
Serial No.:
The serial number is located on the rear of the unit. Retain this
Owner’s Manual in a safe place for future reference.
FOR U.K. CUSTOMERS
If the socket outlets in the home are not suitable for the plug
supplied with this appliance, it should be cut off and an
appropriate 3 pin plug fitted. For details, refer to the
instructions described below. Note that the plug severed from
the mains lead must be destroyed, as a plug with bared
flexible cord is hazardous if engaged in a live socket outlet.
IMPORTANT
THE WIRES IN MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this apparatus
may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the
terminal which is marked with the letter N or coloured
BLACK. The wire which is coloured BROWN must be
connected to the terminal which is marked with the letter L or
coloured RED. Make sure that neither core is connected to the
earth terminal of the three pin plug.
CAUTION
Danger of explosion if battery is incorrectly replaced. Replace
only with the same or equivalent type.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation exposure.
CONTENTS
BASIC OPERATION
OVERVIEW ........................................................... 2
FEATURES............................................................. 3
USING THIS MANUAL ........................................ 4
SUPPLIED ACCESSORIES ................................. 5
CONTROLS AND FUNCTIONS ......................... 6
PLAYBACK ..........................................................37
Front panel ................................................................. 6
Front panel display .................................................... 7
Rear panel .................................................................. 8
Remote control........................................................... 9
BEAM MODE .......................................................40
INSTALLATION ................................................. 11
Before installing this unit......................................... 11
Installing this unit .................................................... 11
CONNECTIONS .................................................. 14
5 beam mode............................................................ 41
Stereo plus 3 beam mode......................................... 41
3 beam mode............................................................ 42
Stereo mode ............................................................. 42
Target mode ............................................................. 43
ENJOYING SURROUND SOUND .....................44
Enjoying 2-channel sources
in surround sound ................................................ 45
Enjoying TV in surround sound .............................. 46
Adjusting surround mode parameters...................... 47
USING SOUND FIELD PROGRAMS................49
What is a sound field? ............................................. 49
Turning on CINEMA DSP programs ...................... 50
Turning off CINEMA DSP programs ..................... 51
Adjusting CINEMA DSP levels .............................. 51
SETUP
Connecting a TV...................................................... 15
Connecting a DVD player/recorder ......................... 16
Connecting a VCR................................................... 17
Connecting a digital satellite tuner
or a cable TV tuner .............................................. 18
Connecting other external components ................... 19
Connecting a subwoofer .......................................... 20
Connecting the power supply cable......................... 21
Selecting the input source........................................ 37
Playing back sources ............................................... 38
Adjusting the volume............................................... 38
Muting the sound ..................................................... 39
PREPARATION
PREPARATION
INTRODUCTION
INTRODUCTION
USING THE VOLUME MODE ..........................52
USING TruBass.....................................................54
USING THE SLEEP TIMER ..............................55
Setting the sleep timer ............................................. 55
Canceling the sleep timer ........................................ 56
GETTING STARTED.......................................... 22
Installing batteries in the remote control ................. 22
Operation range of the remote control..................... 22
Using the remote control ......................................... 23
Turning on the power............................................... 23
USING SET MENU.............................................. 24
Displaying the OSD................................................. 24
The flow chart of SET MENU................................. 25
The flow chart of AUTO SETUP ............................ 26
Installing the optimizer microphone........................ 27
Using AUTO SETUP .............................................. 28
USING THE SYSTEM MEMORY .................... 34
Saving settings ......................................................... 34
Loading settings....................................................... 35
ADVANCED OPERATION
BASIC SETUP.......................................................57
MANUAL SETUP.................................................63
Using MANUAL SETUP ........................................ 64
BEAM MENU ......................................................... 65
SOUND MENU....................................................... 69
INPUT MENU......................................................... 71
DISPLAY MENU.................................................... 73
ADVANCED
OPERATION
AUTO SETUP....................................................... 26
BASIC
OPERATION
SETUP
ADJUSTING SYSTEM PARAMETERS ...........75
Setting the maximum volume level ......................... 75
Protecting the current settings ................................. 76
Initializing the current settings ................................ 77
Adjusting the audio balance .................................... 78
SELECTING THE INPUT MODE .....................81
REMOTE CONTROL FEATURES ...................82
ADDITIONAL
INFORMATION
Setting remote control codes ................................... 82
Controlling other components ................................. 83
Using the TV macro ................................................ 85
ADDITIONAL INFORMATION
TROUBLESHOOTING .......................................87
GLOSSARY...........................................................90
Audio formats .......................................................... 90
Audio information ................................................... 90
English
INDEX....................................................................91
SPECIFICATIONS...............................................92
1
OVERVIEW
OVERVIEW
It is generally accepted that in order to fully enjoy the benefits of surround sound at home, you must endure the agony of
wiring and installing a great number of speakers in the hope that your listening room will give you the same kind of
surround sound experience as your local movie theater.
YAMAHA YSP-800 Digital Sound Projector challenges this preconception that complicated speaker setup and
troublesome wiring go hand-in-hand with the enjoyment of multi-channel surround sound.
This slimline unit does away with the need for complicated wiring and installation worries, leaving you with a unit that is
not only easy to set up, but which is also capable of reproducing the kind of powerful surround sound you have been
waiting for from its built-in subwoofers (2) and individual speakers (21).
You can fine-tune the parameters of this unit to adjust the delay time for separate sound beams, resulting in highly
directional sound that comes in on the listening position from all directions.
The YSP-800 projects sound beams containing surround sound information for the front right (R), front left (L), surround
right (SR) and surround left (SL) speaker positions, which are reflected off the walls of your listening room before
reaching the actual listening position. With the addition of center (C) sound beams, this Digital Sound Projector creates
true-to-life 5.1 channel surround sound that makes you feel as if there are actual speakers around the room.
Sit back and enjoy the real sound experience of this simple, yet stylish Digital Sound Projector.
Imaginary
front right
speaker
R
C
SR
L
SL
Imaginary
surround right
speaker
Imaginary
front left
speaker
Imaginary
center
speaker
Listening position
Imaginary
surround left
speaker
2
FEATURES
FEATURES
◆
◆
◆
◆
◆
5 beam mode
ST(STEREO)+3 beam mode
3 beam mode
Stereo mode
Target mode
Cinema DSP Digital
This unit employs the Cinema DSP Digital technology
developed by YAMAHA Electronics Corp. so that you can
experience movies at home with all the dramatic sound
impact that the director intended to convey.
OSD (on-screen display)
This unit employs the OSD which is basically a
superimposed screen image displayed on your video
monitor. The OSD is used to display the system
information or adjust settings for the system parameters.
Versatile Remote Control
The supplied remote control come with preset remote
control codes to be used to control the DVD player, VCR,
cable TV tuner and digital satellite tuner connected to this
unit. In addition, the remote control is equipped with the
macro capability so that you can perform a series of
operations with the press of a single button.
The “
” logo and “Cinema DSP” are registered
trademarks of YAMAHA Corporation.
AUTO SETUP
This unit employs the automatic sound beam optimization
using the YAMAHA Parametric Room Acoustic
Optimizer (YPAO) technology with the aid of the supplied
optimizer microphone so that you can avoid troublesome
listening-based speaker setup and achieve highly accurate
sound beam adjustments that best match your listening
environment.
INTRODUCTION
Digital Sound Projector
This unit employs the digital sound projector technology
that allows one slim unit to control and steer multiple
channels of sound to generate full, physical 5.1 channel
surround sound, thus eliminating the need for satellite
loudspeakers and cabling normally associated with
conventional surround sound systems. This unit is also
equipped with the following 5 beam modes so that you can
choose the behavior of sound beams that best matches
your listening environment.
Compatibility with the Newest Technologies
This unit employs decoders compatible with Dolby
Digital, DTS (Digital Theater Systems), Dolby Pro Logic,
Dolby Pro Logic II and DTS Neo:6.
◆ Dolby Digital
This is the standard audio signal format used on DVDs and
other purely digital media. This surround technology deliver
high-quality digital audio for up to 5.1 discrete channels to
produce a directional and more realistic effect.
◆ DTS (Digital Theater Systems)
This is an audio signal format used on DVDs and other purely
digital media. This surround technology deliver high-quality
digital audio for up to 5.1 discrete channels to produce a
directional and more realistic effect.
◆ Dolby Pro Logic
This sophisticated, matrix decoding technology up-converts
any 2 channel source audio to a 5.1 channel full bandwidth
playback, resulting in a surround sound experience.
◆ Dolby Pro Logic II
This is fundamentally a redesigned version of Dolby Pro
Logic that employs 2 stereo surround channels, a subwoofer
and a greatly enhanced steering logic. As a result, this
improved technology provides an exceptionally stable sound
field that simulates 5.1 to a much greater degree than the
original Dolby Pro Logic. In addition, Dolby Pro Logic II
features Movie, Music and Game modes specifically designed
for movies, music and games respectively.
◆ DTS Neo:6
This technology decodes the conventional 2 channel sources
for 6 channel playback, enabling playback with the full-range
channels with higher separation. Music mode and Cinema
mode are available to play back music and movie sources
respectively.
Manufactured under license from 1 Ltd. Worldwide patents
applied for.
The ‘
’ logo and ‘Digital Sound Projector™’ are trademarks
of 1 Ltd.
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, and the double-D symbol are trademarks
of Dolby Laboratories.
“DTS”, and “Neo:6” are trademarks of Digital Theater Systems,
Inc.
3
English
TruBass, SRS and the “
” symbol are registered trademarks
of SRS Labs, Inc. TruBass technology is incorporated under
license from SRS Labs, Inc.
USING THIS MANUAL
USING THIS MANUAL
Notes
• This manual describes how to connect and operate this unit. For details regarding the operation of external components, refer to the
supplied owner’s manual for the component.
• Some operations can be performed by using either the buttons on the main unit or on the remote control. In such cases, the operation is
described using remote control operation.
• y indicates a tip for your operation.
• This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In
case of differences between the manual and product, the product has priority.
1
Install this unit in your listening room.
See “INSTALLATION” on page 11.
2
Connect this unit to your TV and other external components.
See “CONNECTIONS” on page 14.
3
Prepare the remote control and turn on the power of this unit.
See “GETTING STARTED” on page 22.
4
Run AUTO SETUP.
See “AUTO SETUP” on page 26.
5
Play back a source and enjoy surround sound.
See “PLAYBACK” on page 37.
If you want to make additional settings
and adjustments
6
4
Run MANUAL SETUP and set remote control codes to fine-tune settings.
See “MANUAL SETUP” on page 63 and “REMOTE CONTROL FEATURES” on page 82.
SUPPLIED ACCESSORIES
SUPPLIED ACCESSORIES
Remote control (×1)
STANDBY/ON
POWER
POWER
AV
TV
VCR
STB
TV
INPUT1
TV
INPUT2
MACRO
DVD
Batteries (×2)
(AA, R6, UM-3)
INTRODUCTION
Check that you have received all of the following parts.
Optical cable (×1)
AUX
INPUTMODE
SLEEP
OSD video pin cable (×1)
YSP
5BEAM
ST+3BEAM
3BEAM
1
2
3
STEREO
TARGET
4
5
6
MUSIC
MOVIE
VOL MODE
8
9
SPORTS
OFF
SURROUND
0
7
+10
CH LEVEL
CINEMA DSP
Digital audio pin cable (×1)
(Orange)
(Yellow)
MENU
Optimizer microphone (×1)
Audio pin cable (×1)
ENTER
RETURN
TEST
VOLUME
CH
TV VOL
MUTE
TV INPUT
TV MUTE
(White/Red)
CODE SET
Cable clamp (×1)
Fastener (×4)
Cardboard microphone
stand (×1)
English
5
CONTROLS AND FUNCTIONS
CONTROLS AND FUNCTIONS
Front panel
1
2
4
5
INPUT
VOLUME
1 OPTIMIZER MIC jack
Use to connect the supplied optimizer microphone to be
used to run AUTO SETUP (see page 27).
2 Front panel display
Shows information about the operational status of this
unit.
3 Remote control sensor
Receives infrared signals from the remote control.
4 INPUT
Press repeatedly to switch between input sources (TV,
VCR, DVD or AUX). See page 37 for details.
5 VOLUME –/+
Controls the volume level of all audio channels (see
page 38).
6
3
6
+
STANDBY/ON
6 STANDBY/ON
Turns on the power of this unit or sets it to the standby
mode (see page 23).
Notes
• When you turn on the power of this unit, you will hear a click
and there will be a 4 to 5-second delay before it can reproduce
sound.
• In the standby mode, this unit consumes a small amount of
power in order to receive infrared-signals from the remote
control.
CONTROLS AND FUNCTIONS
Front panel display
2
NIGHT
SLEEP
3
PCM
INTRODUCTION
1
4
DIGITAL
PL
VOL
m
ft
mS
dB
5
1 NIGHT indicator
Lights up when you select a volume mode (see page 52).
4 Volume level indicator
Shows the current volume level (see page 38).
2 SLEEP indicator
Lights up when the sleep timer is turned on (see page 55).
5 Multi-information display
Shows information when you adjust the parameters of this
unit.
3 Decoder indicators
Light up when the corresponding decoder of this unit is in
operation (see page 44).
y
You can adjust the brightness of the front panel display using the
DISPLAY MENU parameters in MANUAL SETUP (see
page 73).
English
7
CONTROLS AND FUNCTIONS
Rear panel
9
1
VCR
2
TV/STB
AUDIO INPUT
3
4
SUBWOOFER VIDEO
OUT
5
(U.S.A. and Canada models)
6
AUX
TV/STB
OPTICAL
7
8
DVD
COAXIAL
SYSTEM
CONNECTOR
DIGITAL INPUT
1 VCR analog audio input jacks
Use to make an analog connection to your VCR
(see page 17).
6 AUX OPTICAL DIGITAL INPUT jack
Use to connect an external component via an optical
digital connection (see page 19).
2 TV/STB analog audio input jacks
Use to make an analog connection to your TV, digital
satellite tuner and cable TV tuner (see pages 15 and 18).
7 DVD COAXIAL DIGITAL INPUT jack
Use to connect a DVD player via a coaxial digital
connection (see page 16).
3 SUBWOOFER OUT jack
Use to connect a subwoofer (see page 20).
8 SYSTEM CONNECTOR jack
(U.S.A. and Canada models only)
Use to connect a YAMAHA subwoofer equipped with a
SYSTEM CONNECTOR jack to this unit (see page 20).
4 VIDEO OUT jack
Use to connect to the video input terminal of your TV to
display the OSD of this unit (see page 15).
5 TV/STB OPTICAL DIGITAL INPUT jack
Use to connect a TV, digital satellite tuner and cable TV
tuner via an optical digital connection (see pages 15 and
18).
8
9 AC power supply cable
Use to connect to the AC wall outlet (see page 21).
CONTROLS AND FUNCTIONS
Remote control
y
You can also control other components using the remote control
once you set the appropriate remote control codes. See
“Controlling other components” on page 83 for details.
POWER
POWER
AV
TV
VCR
STB
TV
INPUT1
TV
INPUT2
MACRO
INPUTMODE
SLEEP
STANDBY/ON
2
3
DVD
4
AUX
7
8
YSP
5BEAM
ST+3BEAM
3BEAM
1
2
3
STEREO
TARGET
4
5
6
MUSIC
MOVIE
VOL MODE
7
8
9
SPORTS
OFF
SURROUND
0
CH LEVEL
G
5
TruBass
Use to effectively reproduce the bass sound (see page 54).
I
J
6 YSP
Switches to the operation mode of this unit.
K
L
M
MENU
ENTER
VOLUME
CH
MUTE
TV INPUT
TV MUTE
CODE SET
8 Sound field program buttons
Use to select sound field programs (see page 49).
9 CH LEVEL
Adjusts the volume level of each channel (see page 79).
0 Cursor buttons
/
/ / , ENTER
Use to select and adjust SET MENU items.
A TEST
Outputs a test tone when adjusting the output level of each
speaker (see page 78).
Q
B VOLUME +/–
Increases or decreases the volume level of this unit (see
page 38).
TV VOL
B
7 Numeric buttons
Use to enter numbers.
P
RETURN
TEST
A
4 Input selector buttons
Use to select an input source (TV, STB, VCR, DVD or
AUX) and change the control area (see page 37).
H
O
0
E
F
N
+10
CINEMA DSP
9
C
D
2 STANDBY/ON
Sets this system to the standby mode (see page 23).
3 Transmission indicator
Lights up when infrared control signals are being output.
1
5
6
1 Infrared window
Outputs infrared control signals. Aim this window at the
component you want to operate.
R
S
INTRODUCTION
This section describes the function of each control on the
remote control used to control this system.
C MUTE
Mutes the sound. Press again to restore the audio output to
the previous volume level (see page 39).
D TV INPUT
Switches the input source of the TV (see page 83).
E DVD player/VCR control buttons
Use to control the DVD player of the VCR (see pages 83
and 84).
F TV POWER
Turns on the power of the TV or sets it to the standby
mode (see page 83).
H INPUT1/INPUT2
Selects the input source of the TV.
9
English
G AV POWER
Turns on the power of the selected component or sets it to
the standby mode (see pages 83 and 84).
CONTROLS AND FUNCTIONS
I MACRO
Use to set the TV macro (see page 85).
J INPUTMODE
Switches between input modes (AUTO, DTS or
ANALOG). See page 37 for details.
K SLEEP
Sets the sleep timer (see page 55).
L Beam mode buttons
Change the beam mode settings (see page 40).
M VOL MODE
Turns on or off the volume modes (see page 52).
N SURROUND
Selects the surround mode for playback (see page 44).
O MENU
Displays the setup menu on your TV monitor (see
pages 28, 57 and 64).
Note
The DVD menu is displayed when DVD is selected as the input
source.
P RETURN
Use to select sleep timer settings or return to the previous
SET MENU screen.
Q TV VOL +/–
Adjusts the volume level of the TV (see page 83).
R CH +/–
Switches between channels of the TV or the VCR (see
pages 83 and 84).
S TV MUTE, CODE SET
Mutes the audio output of the TV (see page 83).
Use to set up remote control codes (see page 82).
10
INSTALLATION
INSTALLATION
This section describes a suitable installation location to install the unit using a metal wall bracket, a rack or a stand.
Before installing this unit
Install this unit where there are no obstacles such as
furniture obstructing the path of sound beams. Otherwise,
the desired surround sound effects may not be achieved.
You may install this unit in parallel with the wall or in the
corner.
Parallel installation
Install this unit in the exact center of the wall when it is
measured from the left and right corners.
PREPARATION
This unit creates surround sound by reflecting projected
sound beams off the walls of your listening room. The
surround sound effects produced by this unit may not be
sufficient when the unit is installed in the following
locations.
• Rooms with surfaces inadequate for reflecting sound
beams
• Rooms with acoustically absorbent surfaces
• Rooms with measurements outside the following range
W (3 to 7 m) x H (2 to 3.5 m) x D (3 to 7 m)
• Rooms with less than 2 m from the listening position to
the speaker positions
• Rooms where objects such as furniture are likely to
obstruct the path of sound beams
• Rooms where the listening position is close to the walls
• Rooms where the listening position is not in front of
this unit
Make sure you leave an adequate amount of ventilation
space so that heat can escape. Make at least 5 cm of space
above or below this unit.
Installing this unit
An object, such as furniture
Side view
5 cm or more
Corner installation
Install this unit in the corner at a 40º to 50º angle from the
adjacent walls.
40° to 50°
Front
Rear
Notes
An object, such as furniture
y
The availability of the beam mode depends on the installation
location of this unit (see page 40). All five beam modes are
available for the parallel installation whereas the 3 beam and 5
beam modes are not available for the corner installation.
English
• We do not recommend installing this unit so that it is positioned
directly on the floor of your listening room. Please install this
unit using a metal wall bracket, rack or stand.
• This unit weighs 9.0 kg (19.8 lbs). Be sure to install this unit
where it will not fall subject to vibrations, such as from an
earthquake, and where it is out of the reach of children.
• When using a cathode-ray tube (CRT) TV, do not install this
unit directly above your TV.
• This unit is shielded against magnetic rays. However, if the
picture on your TV screen becomes blurred or distorted, we
recommend moving the speakers away from your TV.
11
01EN_02_Prep_YSP-800_UB.fm Page 12 Tuesday, May 30, 2006 3:35 PM
INSTALLATION
■ Using a metal wall bracket
■ Using a stand
You can use the optional metal wall bracket to mount this
unit on the wall in your listening room.
You can mount your TV on the stand placed on a
commercially available rack to install this unit under your
TV.
Metal wall bracket
Stand
TV
This unit
TV
y
Refer to the instructions supplied with the metal bracket for
details on how to attach the metal bracket to the wall or how to
attach this unit to the metal bracket.
Note
This unit is the model that the metal apparatuses are not attached
to the rear panel. If there is the section of “Detach the metal
apparatuses from the Sound Projector” in the instructions
supplied with the metal bracket, skip the section and proceed to
the next. Also, use the supplied projector mounting screws (M4,
spare) instead if there is the information about using screws of the
metal apparatus (M4) in the section of “Attach the small wall
mount brackets to the Sound Projector”.
This unit
y
Refer to the instructions supplied with the stand for details on
how to install the stand or how to mount this unit and the TV on
the stand.
■ Using a rack
You can install this unit either above or under your TV in a
commercially available rack.
When this unit is installed above your TV
When this unit is installed under your TV
Note
Make sure that the rack is large enough to allow adequate
ventilation space around this unit (see page 11) and that it is
strong enough to support the weight of both this unit and your TV.
12
INSTALLATION
■ Affixing this unit
Peel off the film from each of the four supplied fasteners
and then secure them to the bottom four corners of this
unit and the top of the rack, etc.
This unit
PREPARATION
Peel off 2
the film
1
Fasteners
Notes
• Do not install this unit on top of a slanted surface. This unit may
fall over and cause injury.
• Make sure you wipe the surface of the rack, etc. before securing
the fasteners. Applying the tape to a dirty or wet surface will
weaken the sticking power of the tape, and this unit may fall as
a result.
English
13
CONNECTIONS
CONNECTIONS
This unit is equipped with two optical digital jacks, one coaxial digital jack and two types of analog jacks for connecting
external components such as your TV, DVD player, VCR, digital satellite tuner, cable TV tuner and game console.
Further, by connecting a subwoofer to this unit, you can enjoy reinforced low bass sounds. For details on how to connect
various types of external components to this unit, see pages 15 to 20.
CAUTION
Do not connect this unit or other components to the main power until all connections between components are complete.
Audio connection
Video connection
TV
This unit
DVD player
14
Subwoofer
VCR
Digital satellite tuner, cable TV
tuner or game console
CONNECTIONS
Connecting a TV
You can connect a TV to this unit and display the OSD for easy viewing when you adjust the system parameters in SET
MENU.
Note
If you connect this unit to the analog audio and optical digital audio output jacks at the same time as shown in the left illustration below,
the digital audio signals output at the optical digital output jack take priority over the analog audio signals output at the analog audio
output jacks.
■ Digital and analog audio connections
■ Video connections
Analog audio
output
R
PREPARATION
TV
TV
Optical digital
output
Video
input
L
Rear panel of this unit
VCR
TV/STB
AUDIO INPUT
SUBWOOFER VIDEO
OUT
AUX
TV/STB
OPTICAL
DVD
COAXIAL
SYSTEM
CONNECTOR
Rear panel of this unit
VCR
TV/STB
AUDIO INPUT
DIGITAL INPUT
(U.S.A. and Canada models)
Cables used for connections
OUT
AUX
TV/STB
OPTICAL
DVD
COAXIAL
SYSTEM
CONNECTOR
DIGITAL INPUT
(U.S.A. and Canada models)
Cables used for connections
Audio pin cable
(White)
SUBWOOFER VIDEO
OSD video pin cable (supplied)
(White)
(Yellow)
(Yellow)
(Red)
(Red)
Optical cable (supplied)
English
15
CONNECTIONS
Connecting a DVD player/recorder
To connect a DVD player/recorder, connect the coaxial digital output jack on your DVD player to the coaxial digital
input jack (DVD COAXIAL) on this unit.
If there is no coaxial digital output jack on your DVD player/recorder, use them with optical digital connection.
DVD/VCR combo
player/recorder
DVD player/recorder
Video signal to a TV
Video signal to a TV
Analog audio
output
R
Coaxial digital
output
Coaxial digital
output
L
Rear panel of this unit
VCR
TV/STB
SUBWOOFER VIDEO
AUDIO INPUT
TV/STB
AUX
OPTICAL
OUT
DVD
COAXIAL
SYSTEM
CONNECTOR
DIGITAL INPUT
(U.S.A. and Canada models)
Cables used for connections
Digital audio pin cable (supplied)
Audio pin cable
(White)
(Orange)
(Red)
16
(White)
(Orange)
(Red)
CONNECTIONS
Connecting a VCR
To connect a VCR, connect the analog audio output jacks on your VCR to the analog audio input jacks (VCR R/L) on
this unit.
Connect red plugs to the right jacks and white plugs to the left jacks.
VCR
Video signal to a TV
PREPARATION
Analog audio
output
R
L
Rear panel of this unit
VCR
TV/STB
SUBWOOFER VIDEO
AUDIO INPUT
TV/STB
AUX
OPTICAL
OUT
DVD
COAXIAL
SYSTEM
CONNECTOR
DIGITAL INPUT
(U.S.A. and Canada models)
Cables used for connections
Audio pin cable
(White)
(Red)
(White)
(Red)
English
17
CONNECTIONS
Connecting a digital satellite tuner or a cable TV tuner
To connect a digital satellite tuner or a cable TV tuner, connect the optical digital output jack on your digital satellite
tuner or cable TV tuner to the optical digital input jack (TV/STB OPTICAL) on this unit. In addition, connect the analog
audio output jacks on your VCR to the analog audio input jacks (TV/STB R/L) on this unit.
Connect red plugs to the right jacks and white plugs to the left jacks.
Note
If your TV and tuner connected to this unit do not support digital broadcasting, connect the analog audio output jacks (TV/STB R/L) on
this unit to the analog audio output jacks on your TV.
TV
Digital satellite tuner or a cable TV tuner
Video signal to a TV
Analog audio
output
Analog audio
output
R
R
L
Optical digital
output
L
Rear panel of this unit
VCR
TV/STB
SUBWOOFER VIDEO
AUDIO INPUT
OUT
TV/STB
AUX
OPTICAL
DVD
COAXIAL
SYSTEM
CONNECTOR
DIGITAL INPUT
(U.S.A. and Canada models)
Cables used for connections
Optical cable (supplied)
Audio pin cable
(White)
(Red)
18
(White)
(Red)
CONNECTIONS
Connecting other external components
To connect other external components, connect the optical digital output jack on the component to the optical digital
input jack (AUX OPTICAL) on this unit.
You can connect a DVD player/recorder or a component that supports optical digital connections.
Game console, etc.
Video signal to a TV
PREPARATION
Optical fiber cable
Optical digital
output
Attach to this unit
To prevent cables from becoming
unplugged, place the supplied
cable clamp with the open side
facing upward, attach it to the
rear panel of this unit in a suitable
position and then affix cables in
the cable clamp.
Rear panel of this unit
VCR
TV/STB
SUBWOOFER VIDEO
AUDIO INPUT
OUT
TV/STB
AUX
OPTICAL
DVD
COAXIAL
SYSTEM
CONNECTOR
DIGITAL INPUT
(U.S.A. and Canada models)
Cables used for connections
Optical cable (supplied)
English
19
CONNECTIONS
Connecting a subwoofer
To connect a subwoofer, connect the monaural input jack on your subwoofer to the monaural audio output jack
(SUBWOOFER OUT) on this unit.
If a subwoofer is connected to this unit, turn on the power of your subwoofer and then run AUTO SETUP (see page 26)
or select SWFR for BASS OUT in SUBWOOFER SET (see page 70).
Connecting to the SYSTEM CONNECTOR jack (U.S.A. and Canada models only)
When connecting a YAMAHA subwoofer equipped with a SYSTEM CONNECTOR jack, connect it to the SYSTEM
CONNECTOR jack on this unit. If the subwoofer is connected using a system type connection, changing the power mode
of this unit controls the power mode of the subwoofer.
Subwoofer
Monaural
input
System
connector
(U.S.A. and Canada models only)
Rear panel of this unit
VCR
TV/STB
SUBWOOFER VIDEO
AUDIO INPUT
OUT
TV/STB
AUX
OPTICAL
DVD
COAXIAL
SYSTEM
CONNECTOR
DIGITAL INPUT
(U.S.A. and Canada models)
Cables used for connections
Subwoofer pin cable
20
System connector cable
(supplied with the YAMAHA subwoofer with
the SYSTEM CONNECTOR jack)
CONNECTIONS
Connecting the power supply cable
Once all other connections are complete, plug the power supply cable into the AC wall outlet.
PREPARATION
To the AC outlet
English
21
GETTING STARTED
GETTING STARTED
Installing batteries in the remote
control
Operation range of the remote
control
The remote control transmits a directional infrared beam.
Use the remote control within 6 m of this unit and point it
toward the remote control sensor on this unit during
operation.
Press
Approximately
6 m (20 ft)
1
Press and hold the
mark on the battery
cover and then slide off the cover.
2
Insert the two supplied batteries (AA, R6,
UM-3) into the battery compartment.
Make sure you insert the batteries according to the
polarity markings (+/–).
3
Close the battery cover.
Notes
• Change all of the batteries if you notice the following
conditions; the operation range of the remote control decreases,
the indicator does not blink or its light becomes dim.
• Do not use old batteries together with new ones.
• Do not use different types of batteries (such as alkaline and
manganese batteries) together. Read the packaging carefully as
these different types of batteries may have the same shape and
color.
• Exhausted batteries may leak. If the batteries have leaked,
dispose of them immediately. Avoid touching the leaked
material or letting it come into contact with clothing, etc. Clean
the battery compartment thoroughly before installing new
batteries.
• Do not throw away batteries with general house waste. Dispose
of them correctly in accordance with your local regulations.
• The contents of the memory stored in the remote control may be
erased in the following cases:
– The remote control is left without batteries for more than 2
minutes.
– Exhausted batteries remain in the remote control.
– The buttons on the remote control are accidentally pressed
when you change batteries.
• If the memory stored in the remote control is unwantedly
erased, insert new batteries and reset the remote control codes
again.
22
Notes
• Do not spill water or other liquids on the remote control.
• Do not drop the remote control.
• Do not leave or store the remote control in the following types
of conditions:
– places of high humidity, such as near a bath
– places of high temperatures, such as near a heater or a stove
– places of extremely low temperatures
– dusty places
• Do not expose the remote control sensor on this unit to direct
sunlight or lighting such as inverted fluorescent lamps.
• If the batteries grow old, the effective operation distance of the
remote control decreases considerably. If this happens, replace
the batteries with two new ones as soon as possible.
GETTING STARTED
Using the remote control
Turning on the power
The control area and the corresponding functions of the
remote control change depending on the currently selected
input source. Press the input selector buttons (TV, STB,
VCR, DVD or AUX) to select an input source and switch
to the operation mode of the corresponding input source.
Press YSP to switch to the operation mode of this unit.
The buttons on the remote control numbered 3 to 9 are
operational only after you press YSP to switch to the
operation mode of this unit.
y
You can control other components by setting the appropriate
remote control codes (see page 82). Once the remote control code
for each input source (TV, STB, VCR, DVD or AUX) is set, see
“Controlling other components” on page 83 for further
information on the specific functions of the available remote
control buttons for each input source. Note that the buttons on the
remote control numbered 3 to 9 have different functions
depending on the currently selected input source.
VOLUME
+
STANDBY/ON
STANDBY/ON
DVD
1
STB
TV
TV
INPUT2
MACRO
INPUTMODE
SLEEP
VCR
TV
INPUT1
POWER
AV
TV
VCR
STB
TV
INPUT1
TV
INPUT2
MACRO
SETUP
DVD
POWER
AUX
AUX
2
YSP
3
4
5BEAM
ST+3BEAM
3BEAM
1
2
3
STEREO
TARGET
4
5
6
MUSIC
MOVIE
VOL MODE
7
8
9
SPORTS
OFF
SURROUND
0
VT
CH LEVEL
1
TV
Press STANDBY/ON on the front panel or on
the remote control to turn on the power of
this unit.
6
7
+10
CINEMA DSP
or
STANDBY/ON
MENU
8
5
Front panel
Remote control
ENTER
RETURN
TEST
9
2
Press STANDBY/ON on the front panel or on
the remote control again to set this unit to
the standby mode.
1
Input selector buttons
2
YSP
Note
3
Beam mode buttons
4
Sound field program buttons
When the unit is in the standby mode, only STANDBY/ON on the
front panel or on the remote control is operational, and the other
control buttons on the front panel or on the remote control are not
operational until the power of this unit is turned on.
5
Cursor buttons
6
VOL MODE
7
SURROUND
8
MENU
9
RETURN
/
/
/
, ENTER
English
23
USING SET MENU
USING SET MENU
■ Other buttons that display the OSD
Displaying the OSD
This section simply describes how to display the OSD (onscreen display) of this unit on your TV screen and set the
parameters for your listening room. Once this is complete,
you can enjoy real surround sound while watching TV in
the comfort of your own home.
1
2
Check that the video input jack on your TV is
connected to the VIDEO OUT jack of this unit
to display the OSD of this unit.
Press STANDBY/ON on the front panel or on
the remote control to turn on the power of
this unit.
Remote control buttons that
display the OSD
Page
1 Input selector buttons
37
2
54
TruBass
3 Beam mode buttons
40
4 Sound field program buttons
49
5 CH LEVEL
79
6 VOLUME +/–
38
7 MUTE
39
8 INPUTMODE
81
9 SLEEP
55
0 VOL MODE
52
A SURROUND
44
B MENU
or
28, 57, 64
STANDBY/ON
Front panel
3
4
Remote control
Turn on the power of your TV.
3
Press TV on the remote control to display the
OSD of this unit on your TV screen.
It may take a few seconds before this unit’s OSD
appears on your TV screen.
If the OSD does not appear, use the remote control
provided with your TV to switch the video input until
the OSD appears.
TV
TV
AUTO:ANALOG
OSD screen example
24
VCR
STB
TV
INPUT1
TV
INPUT2
MACRO
INPUTMODE
SLEEP
DVD
1
2
4
5
YSP
5BEAM
ST+3BEAM
3BEAM
1
2
3
STEREO
TARGET
4
5
6
MUSIC
MOVIE
VOL MODE
7
8
9
SPORTS
OFF
SURROUND
0
+10
VT
CH LEVEL
CINEMA DSP
MENU
ENTER
RETURN
TEST
VOLUME
CH
MUTE
TV INPUT
TV VOL
6
7
8
AUX
TV MUTE
CODE SET
9
0
A
B
USING SET MENU
The flow chart of SET MENU
The following diagram illustrates the overall flow of the setup procedure.
Run AUTO SETUP.
See “AUTO SETUP” on page 26.
If an error occurs
Look for a remedy.
See “Error messages for AUTO SETUP” on page 33 for a complete list of error
messages and possible remedies.
If the problem persists
SETUP
Run BASIC SETUP.
See “BASIC SETUP” on page 57.
Play back audio signals or adjust the settings for the beam mode and the cinema DSP.
See “PLAYBACK” on page 37.
If you want to make additional settings
and adjustments
Run MANUAL SETUP.
See “MANUAL SETUP” on page 63.
y
• If you cannot clearly hear a sound beam from a specific speaker channel, adjust settings for
SETTING PARAMETERS (see page 65) or for BEAM ADJUSTMENT (see page 66) in
BEAM MENU.
• If there are acoustically absorbent objects such as curtains in the path of the sound beams,
adjust settings for TREBLE GAIN in BEAM MENU (see page 68).
English
25
AUTO SETUP
AUTO SETUP
This unit creates a sound field by reflecting sound beams on the walls of your listening room and broadening the
cohesion between speaker channels. Just as you would arrange the speaker position of other audio systems, you need to
set the beam angle to enjoy the best possible sound from this unit.
This unit employs the beam optimization feature and the YAMAHA Parametric Room Acoustic Optimizer (YPAO)
technology with the aid of the supplied optimizer microphone, allowing you to avoid troublesome listening-based
speaker setup and achieving highly accurate sound adjustments that best match your listening environment.
The beam optimization is the automated feature of BASIC SETUP, which creates the best possible surround sound field
without manually setting the parameters for your listening room.
The YAMAHA Parametric Room Acoustic Optimizer (YPAO) technology performs the following checks and
automatically makes appropriate sound adjustments.
DISTANCE:
Checks the phase and the distance of each beam from this unit and adjusts the delay of each channel so that each sound
beam reaches the listening position at the same time.
EQUALIZING:
Adjusts frequency and levels of each channel’s parametric equalizer to reduce coloration across the channels and create a
cohesive sound field. YPAO equalizing calibration incorporates three parameters (frequency, level and Q factor) for each
of the seven bands in its parametric equalizer to provide highly precise automatic adjustment of frequency characteristics.
LEVEL:
Checks and adjusts the sound output level of each channel.
The flow chart of AUTO SETUP
This unit performs a series of checks to optimize the beam angle, delay, volume and quality. You can choose to optimize
all or part of the parameters.
Notes
Checking the environment
of your listening room
*1 The subwoofer checking procedure is skipped if BEAM
OPTIMZ only is selected.
*2 The beam angle checking procedure is skipped if SOUND
OPTIMZ only is selected.
*3 The YPAO sound optimization procedure is skipped if BEAM
OPTIMZ only is selected.
*1
Checking the subwoofer
*2
Optimizing the beam angle
Beam
optimization
*3
Optimizing the beam delay,
frequency and volume
26
YPAO sound
optimization
AUTO SETUP
Installing the optimizer microphone
The supplied optimizer microphone collects and analyzes the sound that this unit produces in your actual listening
environment. Follow the procedure below to connect the optimizer microphone to this unit and make sure that the
optimizer microphone is placed in a proper location and that there are no large obstacles between the optimizer
microphone and the walls in your listening room.
Notes
CROSSOVER
HIGH CUT
VOLUME
MIN
SETUP
• After you have completed the AUTO SETUP procedure, be sure to disconnect the optimizer microphone.
• The optimizer microphone is sensitive to heat.
– Keep it away from direct sunlight.
– Do not place it on top of this unit.
• Do not connect the optimizer microphone to an extension cable as doing so may result in an inaccurate sound optimization.
• An error may occur during the AUTO SETUP procedure if the optimizer microphone is not properly placed in your listening room. To
avoid the possibility of an error:
– Do not place the optimizer microphone to the extreme right or left from the center of this unit.
– Do not place the optimizer microphone within 2 m from the front of this unit.
– Do not place the optimizer microphone more than 1 m from the center height of this unit.
• Make sure that there are no obstacles between the optimizer microphone and the walls in your listening room as these objects obstruct
the path of sound beams. However, any objects that are in contact with the walls will be regarded as a protruding part of the walls.
• The best possible results are achieved if the optimizer microphone is placed at the same height as your ears would be when you are
seated in your listening position. However, if this is not possible, you can manually fine-tune the sound beam angle and balance the
sound beam output levels using MANUAL SETUP (see page 63) once the AUTO SETUP procedure is completed.
• If a subwoofer with adjustable volume and crossover/high cut frequency controls is connected to this unit, set the volume between 9
and 12 o’clock as viewed on a conventional clockface and set the crossover/high cut frequency to the maximum.
MAX
MIN
MAX
Subwoofer
y
1
Connect the supplied optimizer microphone
to the OPTIMIZER MIC jack on the front
panel.
You may want to use a tripod or the supplied cardboard
microphone stand to affix the optimizer microphone at the
same height as your ears would be when you are seated in
your listening position.
Example of using a tripod
OPTIMIZER MIC
Optimizer microphone position
Within 1 m
(3.3 ft)
2
Place the optimizer microphone on a flat
level surface more than 2 m from the front of
the unit and within 1 m from the center height
of the unit with the optimizer microphone
head upward at your normal listening
position.
More than 2 m
(6.5 ft)
Within 1 m
(3.3 ft)
Tripod
English
Note
Be sure to place the optimizer microphone on an imaginary
center line drawn from this unit.
27
AUTO SETUP
Example of using the supplied cardboard
microphone stand
Using AUTO SETUP
Once the optimizer microphone is firmly connected to this
unit and properly placed in your listening room, follow the
procedure below to start the AUTO SETUP procedure.
Optimizer microphone position
Within 1 m
(3.3 ft)
More than 2 m
(6.5 ft)
Within 1 m
(3.3 ft)
Cardboard
microphone stand
■ Assembling the supplied cardboard
microphone stand
You will find three separate parts (one circular-shaped part
and two longitudinal-shaped parts) of the cardboard
microphone stand originally put together.
1
2
VOLUME
+
STANDBY/ON
STANDBY/ON
DVD
POWER
POWER
AV
TV
VCR
STB
TV
INPUT1
INPUT2
MACRO
INPUTMODE
SLEEP
AUX
(
)
YSP
3
4
5BEAM
ST+3BEAM
3BEAM
1
2
3
STEREO
UNIVERSAL
4
5
6
MUSIC
MOVIE
NIGHT
7
8
9
SPORTS
OFF
SURROUND
0
CH LEVEL
+10
CINEMA DSP
MENU
ENTER
TEST
1
Disassemble the three parts of the cardboard
microphone stand originally put together.
2
Insert one of the longitudinal-shaped part
into the crevice of the other longitudinalshaped part.
3
Place the circular-shaped part on top of the
two combined longitudinal-shaped parts.
4
Place the supplied optimizer microphone on
top of the circular-shaped part.
28
RETURN
AUTO SETUP
3
Notes
• If your listening room has curtains, open the curtains before
starting the BEAM OPT+SOUND OPTIMZ or the BEAM
OPTIMZ only procedure.
• Make sure that your listening room is as quiet as possible while
this unit is performing the AUTO SETUP procedure.
• Once the AUTO SETUP procedure has started, position
yourself beside or behind this unit so that you may not obstruct
the path of sound beams. To achieve the best results possible,
however, it is strongly recommended that you should evacuate
yourself from your listening room until the AUTO SETUP
procedure is completed.
• Be advised that it is normal for loud test tones to be output
during the AUTO SETUP procedure.
• The AUTO SETUP procedure may not be run successfully if
this unit is installed in one of the rooms described in “Before
installing this unit” on page 11. In such cases, run BASIC
SETUP (see page 57) or MANUAL SETUP (see page 63) to
manually adjust the corresponding parameters.
• If the AUTO SETUP procedure stops and an error message
appears on the screen, see “Error messages for AUTO SETUP”
on page 33 for appropriate remedies.
SET MENU
MENU
.;MEMORY
;AUTO SETUP
;BASIC SETUP
;MANUAL SETUP
p
y
• The control buttons used for SET MENU are displayed on
the bottom of the screen.
• To return to the previous screen while using SET MENU,
press RETURN on the remote control.
• To resume cursor button operations after changing the
control area by pressing an input selector button, press
TEST on the remote control.
• To cancel the SET MENU screen, press MENU once
more.
• You can also perform the following operations in the front
panel display.
• If you press an input selector button during the SET
MENU operations, the cursor buttons become ineffective.
In this case, press TEST once.
Press STANDBY/ON on the front panel or on
the remote control to turn on the power of
this unit.
4
Press
/
on the remote control to select
AUTO SETUP and then press ENTER.
The following screen appears on your TV.
ENTER
or
SETUP
1
p
[]/[]:Up/Down
[ENTER]:Enter
y
You can save the settings optimized by the AUTO SETUP
procedure (see page 34). A set of settings optimized according to
specific conditions of your listening environment can be recalled
later depending on the varying conditions of your listening
environment (see page 35).
Press MENU on the remote control.
The SET MENU screen appears on your TV.
ENTER
STANDBY/ON
Front panel
2
Remote control
Press YSP on the remote control to switch to
the operation mode of this unit.
YSP
;AUTO SETUP
.BEAM+SOUND OPTIMZ
BEAM OPTIMZ only
SOUND OPTIMZ only
p
p
[]/[]:Up/Down
[ENTER]:Enter
English
29
AUTO SETUP
5
Press
/
to select BEAM OPT+SOUND
OPTIMZ, BEAM OPTIMZ only or SOUND
OPTIMZ only and then press ENTER.
The following screen appears on your TV.
6
Press
/
/ / to select and configure
each parameter and then press ENTER.
ENTER
ENTER
ENTER
PREPARATION
.INSTALLING;;Parallel to Wall
MOUNTING;;;;SHELF
REFLECTING;;NORMAL
Set MIC in front of YSP
MIN 2m/6.5ft
INSTALLING (Installing)
Use to select the installed position of the unit in your
listening room.
Choices: Parallel to Wall (Parallel with wall
installation),
Angle to Wall or corner (Corner installation)
Angle to Wall or corner
Parallel to Wall
p
p
[]/[]:Up/Down/[p]/[p]:Sel
[ENTER]:Start
BEAM OPT+SOUND OPTIMZ
(Beam optimization and YPAO sound
optimization)
Use to optimize the beam angle, delay, volume and quality
so that the parameters best match your listening
environment.
It is recommended that you should select this optimization
feature in the following cases:
• If you make settings for the first time.
• If the unit has been relocated.
• If your listening room has been restructured.
• If the objects in your listening room (furniture, etc.)
have been rearranged.
BEAM OPTIMZ only
(Beam optimization only)
Use to optimize the beam angle so that the parameter best
matches your listening environment.
SOUND OPTIMZ only
(YPAO sound optimization only)
Use to optimize the beam delay, volume and quality so
that the parameters best match your listening environment.
It is recommended that you should select this optimization
feature in the following cases:
• If you have opened or closed the curtains in your
listening room before using this unit.
• If you have manually set the beam angle.
Note
You must optimize the beam angle in the BEAM OPTIMZ only
procedure before starting the SOUND OPTIMZ only procedure.
30
• Select Angle to Wall or corner if the unit is installed in
the corner. The beam mode is set to ST+3BEAM (see
page 41).
• Select Parallel to Wall if the unit is installed in parallel
with the wall. The beam mode is set to 5BEAM (see
page 41).
AUTO SETUP
MOUNTING (Mounting)
Use to select the mounted position of the unit in your
listening room.
Choices: SHELF (Shelf mount), WALL (Wall mount)
SHELF
8
Press ENTER to start the AUTO SETUP
procedure.
The following screen appears on your TV.
ENVIRONMENT CHECK (Environmental noise
check), SUB WOOFER CHECK (Subwoofer check)
and WILL START in 10 SEC (Will start in 10 sec) are
displayed in order as the PREPARATION procedure
is in progress.
ENTER
WALL
PREPARATION
REFLECTING (Reflecting)
Use to select the reflectivity of your listening room.
Choices: NORMAL (Normal), HI ECHO (High echo)
• Select NORMAL if your listening room has a normal
reflectivity.
• Select HI ECHO if your listening room has highly
reflective surfaces such as concrete walls.
.ENVIRONMENT CHECK
;;;[OK]
SUB WOOFER CHECK
;;;[NOT IN USE]
WILL START in 10 SEC
Move aside or behind YSP
*****-----
If you selected BEAM
OPT+SOUND OPTIMZ or
SOUND OPTIMZ only in
step 5.
PREPARATION
.ENVIRONMENT CHECK
;;;[OK]
SETUP
• Select WALL if the unit is mounted on the wall.
• Select SHELF if the unit is mounted on the shelf.
WILL START in 10 SEC
Move aside or behind YSP
*****-----
If you selected BEAM
OPTIMZ only in step 5.
AUTO BEAM OPTIMIZATION
7
Check the following points once again before
starting the AUTO SETUP procedure.
• Is the optimizer microphone firmly connected to
this unit?
• Is the optimizer microphone placed in a proper
location?
• Are there any large obstacles in between the
optimizer microphone and the walls in your
listening room?
AUTO BEAM MEASUREMENT/SET
Skipped if you selected
SOUND OPTIMZ only in
step 5.
ACOUSTIC OPTIMIZATION
.SETTING
MEASURE
MEASURE
MEASURE
VOLUME
DISTANCE
FREO CHAR
VOLUME
Skipped if you selected
BEAM OPTIMZ only in
step 5.
31
English
If an error occurs, an error message is displayed. See
“Error messages for AUTO SETUP” on page 33 for a
complete list of error messages and their proper
remedies. Follow the instructions and perform the
AUTO SETUP procedure again.
AUTO SETUP
9
Check that the following screen is displayed
on your TV.
The results of the AUTO SETUP procedure are
displayed on your TV.
Example of the
SHOW RESULT screen
SHOW RESULT
BEAM MODE: 5BEAM
SUBWOOFER: NOT APPLICABLE
[ENTER]:Enter
[RETURN]:Cancel
10
Press ENTER to confirm the results or press
RETURN to cancel the results.
The following screen is displayed temporarily for a
few seconds and then disappear from your TV.
AUTO SETTING COMPLETED
ENTER
32
AUTO SETUP
■ Error messages for AUTO SETUP
Before the AUTO SETUP procedure starts
Error message
ERROR E-2
No MIC Detected. Please check
MIC connection and re-try.
Cause
The optimizer microphone is not
connected to this unit.
Remedy
Connect the optimizer microphone to
this unit.
See
page
27
While the AUTO SETUP procedure is in progressError message
Cause
Remedy
See
page
There is too much unwanted noise in
your listening room.
Make sure that your listening room is as
quiet as possible. You may want to
choose certain hours during the day
when there is not much noise coming
from outside.
—
ERROR E-2
No MIC detected. Please check
MIC connection and re-try.
The optimizer microphone was
disconnected while the AUTO SETUP
procedure was in progress.
Make sure that the optimizer microphone
is firmly connected to this unit.
27
ERROR E-3
Unexpected control is detected.
Please re-try.
Some other operations were performed
on this unit while the AUTO SETUP
procedure was in progress.
Do not perform any other operations
while the AUTO SETUP procedure is in
progress.
—
ERROR E-4
Please check MIC position. MIC
should be set in front of YSP.
The optimizer microphone is not placed
in front of this unit.
Make sure that the optimizer microphone
is installed in front of this unit.
27
ERROR E-5
Please check MIC position. MIC
should be set above 2m/6.5ft.
The optimizer microphone is not placed
in the right distance from this unit.
Make sure that the optimizer microphone
is installed more than 2 m from the front
of this unit and within 1 m from the
center height of this unit.
27
ERROR E-6
Volume level is smaller than
expected. Please check MIC
position/connection and re-try.
The optimizer microphone cannot collect
the sound produced by this unit because
the sound output level is too low.
Make sure that the optimizer microphone
is firmly connected to this unit and
placed in a proper location. If the
problem persists, contact the nearest
YAMAHA service center for assistance.
27
ERROR E-7
Unexpected Error Happened.
Please re-try.
An internal system error occurred.
Repeat the AUTO SETUP procedure.
—
SETUP
ERROR E-1
Please test in more quiet
environment.
English
33
USING THE SYSTEM MEMORY
USING THE SYSTEM MEMORY
Saving settings
3
You can save the current settings adjusted in SET MENU
in the system memory of this unit. It is handy to save
certain settings according to the varying conditions of
your listening environment. For example, if there are
curtains in the path of beams, the effectiveness of the
beams will vary depending on whether the curtains are
open or closed.
When the curtains are
open
Press
/
to select MEMORY and then
press ENTER.
The following screen appears on your TV.
ENTER
ENTER
When the curtains are
closed
;MEMORY
1)LOAD
2)SAVE
1
Press YSP on the remote control to switch to
the operation mode of this unit.
4
p
p
[]/[]:Up/Down
[ENTER]:Enter
Press
/
to select SAVE and then press
ENTER.
The following screen appears on your TV.
YSP
2
Press MENU on the remote control.
The SET MENU screen appears on your TV.
ENTER
ENTER
SET MENU
MENU
.;MEMORY
;AUTO SETUP
;BASIC SETUP
;MANUAL SETUP
p
p
[]/[]:Up/Down
[ENTER]:Enter
y
• The control buttons used for SET MENU are displayed on
the bottom of the screen.
• To return to the previous screen while using SET MENU,
press RETURN on the remote control.
• To resume cursor button operations after changing the
control area by pressing an input selector button, press
TEST on the remote control.
• To cancel the SET MENU screen, press MENU once
more.
• You can also perform the following operations in the front
panel display.
• If you press an input selector button during the SET
MENU operations, the cursor buttons become ineffective.
In this case, press TEST once.
34
2)MEMORY SAVE
p USER1
USER2
[]/[]:Select
p p
USER3
USING THE SYSTEM MEMORY
5
Press / to select USER1, USER2 or
USER3 and then press ENTER.
The following screen appears on your TV.
Loading settings
You can recall the settings saved in “Saving settings” on
page 34 according to the varying conditions of your
listening environment.
1
ENTER
ENTER
Press YSP on the remote control to switch to
the operation mode of this unit.
YSP
2)MEMORY SAVE
USER1 Save Now?
[ENTER]:Enter
2
Press MENU on the remote control.
The SET MENU screen appears on your TV.
SET MENU
MENU
.;MEMORY
;AUTO SETUP
;BASIC SETUP
;MANUAL SETUP
2)MEMORY SAVE
USER1 Saving !
ENTER
[<]/[>]:Select
SET MENU
[]/[]:Up/Down
[ENTER]:Enter
p
Press ENTER again.
The new parameters are saved as USER1, USER2 or
USER3. Once the parameters are saved, the display
returns to the SET MENU screen.
SETUP
p
6
y
• The control buttons used for SET MENU are displayed on
the bottom of the screen.
• To return to the previous screen while using SET MENU,
press RETURN on the remote control.
• To resume cursor button operations after changing the
control area by pressing an input selector button, press
TEST on the remote control.
• To cancel the SET MENU screen, press MENU once
more.
• You can also perform the following operations in the front
panel display.
• If you press an input selector button during the SET
MENU operations, the cursor buttons become ineffective.
In this case, press TEST once.
.;MEMORY
;AUTO SETUP
;BASIC SETUP
;MANUAL SETUP
p
7
p
[]/[]:Up/Down
[ENTER]:Enter
Press MENU to exit.
The SET MENU screen disappears from your TV.
MENU
English
35
USING THE SYSTEM MEMORY
3
Press
/
to select MEMORY and then
press ENTER.
The following screen appears on your TV.
ENTER
5
Press / to select USER1, USER2 or
USER3 and then press ENTER.
The following screen appears on your TV.
ENTER
ENTER
ENTER
;MEMORY
1)MEMORY LOAD
1)LOAD
2)SAVE
USER1 Load Now?
4
p
p
[]/[]:Up/Down
[ENTER]:Enter
[ENTER]:Enter
Press
/
to select LOAD and then press
ENTER.
The following screen appears on your TV.
ENTER
6
Press ENTER again.
The new parameters are saved as USER1, USER2 or
USER3. Once the parameters are saved, the display
returns to the SET MENU screen.
1)MEMORY LOAD
ENTER
USER1 Loading !
ENTER
[<]/[>]:Select
1)MEMORY LOAD
p USER1
USER2
USER3
SET MENU
[]/[]:Select
p p
.;MEMORY
;AUTO SETUP
;BASIC SETUP
;MANUAL SETUP
p
7
Press MENU to exit.
The SET MENU screen disappears from your TV.
MENU
36
p
[]/[]:Up/Down
[ENTER]:Enter
PLAYBACK
PLAYBACK
Press STB on the remote control to play back a
satellite broadcast.
Selecting the input source
You can play back sound from the components connected
to this unit simply by pressing INPUT on the front panel
repeatedly or pressing one of the input selector buttons
(TV, STB, VCR, DVD or AUX) on the remote control.
The name of the selected input source and the type of the
corresponding input mode appear in the front panel
display.
STB
VOL
Press DVD on the remote control to play back a
DVD.
DVD
INPUT
VOLUME
+
STANDBY/ON
VOL
STANDBY/ON
POWER
AV
TV
VCR
STB
TV
INPUT1
TV
INPUT2
MACRO
Press VCR on the remote control to play back a
video tape.
AUX
VCR
BASIC
OPERATION
DVD
POWER
■ Front panel operations
Press INPUT on the front panel repeatedly to
toggle between TV, STB, DVD, VCR and AUX.
The name of the corresponding input source and the type
of the current input mode are shown in the front panel
display.
■ Remote control operations
Press TV on the remote control to play back a TV
program.
VOL
Press AUX on the remote control to play back a
component connected to the AUX jack on the
rear panel of this unit.
AUX
TV
VOL
VOL
English
Name of the selected
input source
Type of the selected
input mode
37
PLAYBACK
Playing back sources
Adjusting the volume
Once an input source is selected (see page 37), you can
play back the selected input source.
Note
This section uses a DVD player as an example of the playback
source.
y
For details on the TV and the DVD player you are using, refer to
the owner’s manual supplied with the TV and the DVD player.
1
2
3
4
Turn on the power of your DVD player using
the remote control supplied with the DVD
player.
INPUT
VOLUME
Switch to the video input on your TV using
the remote control supplied with the TV so
that the DVD menu screen is displayed.
If necessary, turn down the volume of your
TV until you cannot hear any sound.
Press DVD on the remote control to select
DVD as the input source.
+
STANDBY/ON
VOLUME
CH
TV VOL
MUTE
TV INPUT
TV MUTE
Press VOLUME +/– on the front panel or on the
remote control to increase or decrease the
volume level.
The numeric value of the volume level appears in the front
panel display.
Control range: 0.0 dB to –99.5 dB, MIN (minimum)
DVD
5
VOLUME
or
Play back the DVD on your DVD player using
the supplied remote control.
Audio signals from your DVD player are output from
the speakers of this unit.
VOLUME
+
Front panel
Remote control
y
• If the output volume is too low, increase the volume on this unit
to around –25 dB.
• If you have set the appropriate remote control codes for your
TV and DVD player, you can use the remote control supplied
with this unit to operate these components. For details on how
to set remote control codes, see page 82.
VOL
VOLUME MUTE appears at the minimum volume level.
VOL
Notes
• The volume level of all input sources (including multi-channel
as well as stereo sources) changes at the same time.
• 0.5 dB of the volume level increases or decreases each time you
press VOLUME +/–.
• You can continuously increase or decrease the volume level if
you press and hold VOLUME +/–.
38
PLAYBACK
Muting the sound
1
VOLUME
CH
TV VOL
MUTE
TV INPUT
TV MUTE
Press MUTE on the remote control to mute
the sound.
AUDIO MUTE ON appears in the front panel
display, and the volume level indicator flashes.
MUTE
Flashes
VOL
Press MUTE on the remote control again (or
press VOLUME +/–) to resume the sound
output.
AUDIO MUTE OFF appears temporarily in the front
panel display (or the numeric value of the current
volume level appears if you press VOLUME +/–),
and the volume level indicator lights up.
BASIC
OPERATION
2
VOLUME
MUTE
or
Lights up
VOL
Note
English
The sound output of all input sources (including multi-channel as
well as stereo sources) is muted at the same time.
y
You can select whether the sound output is to be muted
completely or by 20 dB when you press MUTE (see page 70).
39
BEAM MODE
BEAM MODE
You can change the beam mode to suit the input source of this unit using the beam mode buttons on the remote control
(STEREO, 3BEAM, 5BEAM, ST+3BEAM or TARGET). Select stereo mode for 2-channel sources, 3 beam mode, 5
beam mode and stereo plus 3 beam mode for 5.1-channel playback.
All the beam modes are available in the following cases:
• If you selected Parallel to Wall for INSTALLING in AUTO SETUP (see page 30)
• If you selected settings other than CORNER RIGHT or CORNER LEFT for INSTALLED POSITION in BASIC
SETUP (see page 59)
• If you selected FLAT TO WALL for INSTALLED POSITION in MANUAL SETUP (see page 65)
Only stereo, stereo plus 3 beam and target modes are available in the following cases:
• If you selected Angle to Wall or corner for INSTALLING in AUTO SETUP (see page 30)
• If you selected CORNER RIGHT or CORNER LEFT for INSTALLED POSITION in BASIC SETUP (see page 59)
• If you selected ANGLE TO WALL OR CORNER for INSTALLED POSITION in MANUAL SETUP (see page 65)
AUTO SETUP
BASIC SETUP
MANUAL SETUP
INSTALLING
(see page 30)
INSTALLED POSITION
(see page 59)
INSTALLED POSITION
(see page 65)
Other settings
FLAT TO
WALL
ANGLE TO
WALL OR
CORNER
Beam
mode
Parallel to
Wall
Angle to Wall
or corner
CORNER
RIGHT
or
CORNER
LEFT
STEREO
Yes
Yes
Yes
Yes
Yes
Yes
3BEAM
Yes
No
No
Yes
Yes
No
5BEAM
Yes
No
No
Yes
Yes
No
ST+3BEAM
Yes
Yes
Yes
Yes
Yes
Yes
TARGET
Yes
Yes
Yes
Yes
Yes
Yes
Note
Yes: the corresponding beam mode is available.
No: the corresponding beam mode is not available.
40
BEAM MODE
INPUTMODE
SLEEP
YSP
5BEAM
ST+3BEAM
3BEAM
1
2
3
STEREO
TARGET
4
5
6
MUSIC
MOVIE
VOL MODE
7
8
9
SPORTS
OFF
SURROUND
0
CH LEVEL
5 beam mode
Outputs sound beams from the front left and right, center,
and surround left and right speakers. This mode is ideal
for enjoying surround sound effects to the fullest when
watching DVDs recorded in a multi-channel format or
playing back 2-channel sources in a multi-channel format.
+10
CINEMA DSP
MENU
Press 5BEAM on the remote control to select the
5 beam mode.
ENTER
RETURN
TEST
5BEAM
1
1
Press YSP on the remote control to switch to
the operation mode of this unit.
Notes
YSP
2
Press one of the beam mode buttons to
select the desired beam mode.
ST+3BEAM
3BEAM
1
2
3
STEREO
TARGET
4
5
Stereo plus 3 beam mode
Outputs sound beams from the front left and right, center,
and surround left and right speakers. This mode is ideal
for watching live recordings on a DVD. Vocals and
instrumental sounds can be heard close to the center of the
listening position while sound reflections from the venue
itself can be heard on your right and left, giving you the
feeling that you are sitting right in front of the stage.
BASIC
OPERATION
5BEAM
• To achieve the best surround sound effect, make sure that there
are no obstacles placed in the path of sound beams in that the
objects may prevent the beams from rebounding directly off the
walls in your listening room.
• The front left and right sound beams are output towards the
walls in your listening room.
Press ST+3BEAM on the remote control to select
the stereo plus 3 beam mode.
ST+3BEAM
2
Note
41
English
The front left and right sound beams are output directly to the
listening position.
BEAM MODE
3 beam mode
Outputs sound beams from the front left and right and
center speakers. This mode is ideal for enjoying movies
with the whole family. Because the listening position area
is widened, you can enjoy excellent quality surround
sound over a wider area.
Press 3BEAM on the remote control to select the
3 beam mode.
Stereo mode
Outputs sound beams from the front left and right
speakers in the 2-channel stereo mode. This mode is ideal
for playing back hi-fi sources, such as CDs, and can be
used to replace your TV speakers.
Press STEREO on the remote control to select
the stereo mode.
STEREO
4
3BEAM
3
y
You can achieve a more realistic surround effect if you adjust
settings for IMAGE LOCATION in BEAM MENU (see page 68).
Notes
• When you play back multi-channel sources, surround left and
right signals are mixed down and output from the front left and
right speakers.
• The front left and right sound beams are output towards the
walls in your listening room.
42
Notes
• When you play back multi-channel sources, all signals except
those for the front left and right speakers are mixed down and
output from the front left and right speakers. No audio is output
from the center and rear channels.
• The surround mode becomes disabled when the stereo mode is
selected.
• When you play back Dolby Digital audio signals in the stereo
mode, the dynamic range becomes compressed. If the volume
level decreases to the extreme, use other beam modes except the
target mode.
• If the stereo mode is selected as the beam mode, the surround
modes (see page 44) and the CINEMA DSP programs (see
page 49) become ineffective.
BEAM MODE
Target mode
Outputs sound beams in a single channel. This mode is
ideal if you do not want the sound beams to be reflected
on the walls in your listening room or if you do not disturb
others asleep while enjoying music or movies at night.
Press TARGET on the remote control to select
the target mode and then press
the angle.
Control range: L90° to R90°
/
to adjust
• Press repeatedly to increase the horizontal angle on
the left side.
• Press repeatedly to increase the horizontal angle on
the right side.
TARGET
5
In addition, you can adjust the horizontal angle of the
sound beams so that you can hear dialogues clearly even
from a distant location such as the kitchen area in your
listening room.
ENTER
VOL
BASIC
OPERATION
Notes
• The sound beams are not rebounded off the walls in your
listening room.
• If the target mode is selected as the beam mode, the surround
modes (see page 44), the CINEMA DSP programs (see
page 49) and the TruBass (see page 54) become ineffective. In
addition, no audio is output from the subwoofer connected to
this unit.
English
43
ENJOYING SURROUND SOUND
ENJOYING SURROUND SOUND
■ Decoder indicators
Depending on the input source and the selected surround
mode, the indicators in the front panel display light up as
follows:
Status
When PCM signals are being
input
Indicator
PCM
When DTS digital signals are
being input or when DTS Neo:6
is selected
When Dolby Digital signals are
being input
When Dolby Pro Logic is
selected
When Dolby Pro Logic II is
selected
Recommended
source
Surround mode
Dolby Pro Logic
–
All sources
Dolby Pro Logic II
Movie
Music
Game
Movies
Music
Games
DTS Neo:6
Cinema
Music
Movies
Music
Notes
DIGITAL
PL
PL
y
• You can select an input mode (AUTO, DTS or ANALOG) by
pressing INPUTMODE on the remote control repeatedly (see
page 81).
• Discs encoded in DTS-ES or Dolby Digital 5.1 EX will be
played back in DTS or Dolby Digital.
44
■ Surround modes and recommended
sources
• Surround modes are available when the beam mode is set to a
setting other than the stereo or the target mode.
• When you select an input source (see page 37), the surround
mode used for the previously selected input source is selected.
• If the power of this unit is turned off and on again, the surround
mode used for the previously selected input source before the
power was turned off is selected.
• The surround modes are available only when the CINEMA DSP
programs are turned off (see page 51) or when the movie
program is selected as the CINEMA DSP program (see
page 50).
• Only Dolby Pro Logic, Dolby Pro Logic II Movie and DTS
Neo:6 Cinema are available when the movie program is selected
as the CINEMA DSP program (see page 50).
• If the surround modes are not available, “Prohibit” appears in
the front panel display when you press SURROUND on the
remote control.
• The surround modes are available only when 2-channel signals
are being input. If you try to switch between the surround
modes when 5.1 channel signals are being input, “Prohibit”
appears in the front panel display.
ENJOYING SURROUND SOUND
Enjoying 2-channel sources
in surround sound
This unit can decode 2-channel sources for 5.1 channel
playback so that you can enjoy a variety of surround sound
effects by switching the surround mode.
2
Press SURROUND on the remote control
repeatedly (or press SURROUND and then
press / ) to switch between surround
modes.
SURROUND
y
The surround modes are available only when the CINEMA DSP
programs are turned off (see page 51) or when the movie program
is selected as the CINEMA DSP program (see page 50). In
addition, the beam mode must be set to the 5 beam mode, the
stereo plus 3 beam mode or the 3 beam mode (see page 40).
or
SURROUND
ENTER
INPUTMODE
SLEEP
YSP
5BEAM
ST+3BEAM
3BEAM
1
2
3
STEREO
TARGET
4
5
6
MUSIC
MOVIE
VOL MODE
7
8
9
SPORTS
OFF
SURROUND
0
CH LEVEL
PRO LOGIC
+10
CINEMA DSP
MENU
PLII Movie
ENTER
RETURN
TEST
PLII Music
1
Press YSP on the remote control to switch to
the operation mode of this unit.
Neo:6 Cinema
Neo:6 Music
YSP
BASIC
OPERATION
PLII Game
Example of the surround
mode display in the front
panel display when the
CINEMA DSP program is
turned off
English
45
ENJOYING SURROUND SOUND
Enjoying TV in surround sound
4
You can enjoy analog audio signals output from your TV
in real surround sound.
Press VOLUME +/– on the remote control to
adjust the volume level.
VOLUME
y
Before performing the steps below, set the volume of this unit to
–40 dB. If necessary, adjust the volume level in step 4 below.
DVD
VCR
STB
TV
INPUT1
TV
INPUT2
MACRO
INPUTMODE
SLEEP
AUX
YSP
5BEAM
ST+3BEAM
3BEAM
1
2
3
STEREO
TARGET
4
5
6
MUSIC
MOVIE
VOL MODE
7
8
9
SPORTS
OFF
SURROUND
0
CH LEVEL
+10
CINEMA DSP
5
Press SURROUND repeatedly (or press
SURROUND and then press / ) on the
remote control to select a surround mode.
Signals input from 2-channel sources are played back
on multiple channels.
For more information on surround modes, see
page 44.
MENU
SURROUND
ENTER
RETURN
TEST
VOLUME
CH
or
TV VOL
SURROUND
ENTER
1
Select the TV channel you want to watch.
To select a TV channel, use the remote control
supplied with your TV.
2
Press TV on the remote control.
This unit outputs audio signals from your TV.
TV
3
46
If you hear sound from your TV speakers,
reduce the volume level of your TV until you
can no longer hear any audio being output.
To reduce the TV volume level, use the remote
control supplied with your TV.
ENJOYING SURROUND SOUND
Adjusting surround mode
parameters
SURROUND
You can configure the parameters for Dolby Pro Logic II
Music and DTS Neo:6 Music to fine-tune the surround
sound effect.
INPUTMODE
or
SURROUND
SLEEP
ENTER
YSP
5BEAM
ST+3BEAM
3BEAM
1
2
3
STEREO
TARGET
4
5
6
MUSIC
MOVIE
VOL MODE
7
8
9
SPORTS
OFF
SURROUND
0
CH LEVEL
+10
CINEMA DSP
PRO LOGIC
MENU
PLII Movie
ENTER
RETURN
TEST
1
PLII Music
PLII Game
Press YSP on the remote control to switch to
the operation mode of this unit.
Neo:6 Cinema
Neo:6 Music
YSP
Press SURROUND on the remote control
repeatedly (or press SURROUND and then
press / ) to select PL II Music or Neo:6
Music.
BASIC
OPERATION
2
Example of the surround
mode display in the front
panel display when the
CINEMA DSP program is
turned off
3
Press
/
to select the parameter.
ENTER
4
Press
/
to configure the parameter.
ENTER
English
47
ENJOYING SURROUND SOUND
■ When Dolby Pro Logic II Music is
selected
PANORAMA
Gives front left and right channel sound a wraparound
effect, distributed throughout the entire surround
sound field to give you an expansive feeling.
Choices: ON/OFF
Default setting: OFF
DIMENSION
Adjusts the difference in volume between front and
surround channels to the volume balance you desire.
Control range: –3 (toward the surround direction) to
+3 (toward the front direction)
Default setting: STD
CT WIDTH
Distributes the center channel sound to the left and
right. If set to 0, center channel sounds output only
from the center speaker.
Control range: 0 to 7
Default setting: 3
■ When DTS Neo:6 Music is selected
C. IMAGE
Adjusts the center image from three speakers (front
and center) to varying degrees.
Control range: 0.0 (wider) to 1.0 (toward the center)
Default setting: 0.3
48
USING SOUND FIELD PROGRAMS
USING SOUND FIELD PROGRAMS
This unit is equipped with a variety of precise digital decoders that allow you to enjoy multi-channel playback from
stereo or multi-channel sources. This unit is also equipped with a YAMAHA CINEMA DSP (digital sound field
processing) chip containing several sound field programs which you can use to enhance your playback experience. Most
of the sound field programs are precise digital recreations of actual acoustic environments found in famous concert halls,
music venues and movie theaters.
y
The YAMAHA CINEMA DSP modes are compatible with all Dolby Digital, DTS and Dolby Surround sources.
Note
Choose a sound field program based on your listening preference and do not purely rely on the name of the sound field program itself.
What is a sound field?
A significant factor that creates the rich, full tones of a live instrument are the multiple reflections from the walls of the
room. In addition to making the sound live, these reflections enable the listener to tell where the player is situated as well
as the size and shape of the room in which the listening is sitting.
■ Elements of a sound field
In any environment, there are two distinct types of sound reflections that combine with the direct sound coming straight
to our ears from the player’s instrument to make up the sound field.
Early reflections
Reflected sounds reach our ears extremely rapidly (50 ms to 100 ms after the direct sound) after reflecting from one
surface only (from the ceiling or a wall, for example). Early reflections help add clarity to the direct sound.
Direct sound, early reflections and subsequent reverberation taken together help us to determine the subjective size and
shape of the room, and it is this information that the digital sound field processor reproduces in order to create sound
fields.
BASIC
OPERATION
Reverberations
These are caused by reflections from more than one surface (i.e. wall, ceiling, the back of the room, etc.) so numerous
that they merge together to form a continuous sonic afterglow. They are non-directional and lessen the clarity of the direct
sound.
If you could create the appropriate early reflections and subsequent reverberations in your listening room, you would be
able to create your own listening environment. The acoustics in your room could be changed to those of a concert hall, a
dance floor or a listening room of virtually any size at all. This ability to create sound fields at will is exactly what
YAMAHA has done with the CINEMA DSP technology.
English
49
USING SOUND FIELD PROGRAMS
Turning on CINEMA DSP programs
You can select from three different sound field programs
(MUSIC, MOVIE and SPORTS) depending on the type of
sources you want to enjoy.
Notes
• The CINEMA DSP programs are not available if the stereo
mode (see page 42) or the target mode (see page 43) is selected
as the beam mode.
• If the CINEMA DSP programs are not available, “Prohibit”
appears in the front panel display when you press one of the
sound field program buttons on the remote control.
INPUTMODE
SLEEP
YSP
5BEAM
ST+3BEAM
3BEAM
3
1
2
STEREO
TARGET
4
5
6
MUSIC
MOVIE
VOL MODE
7
8
9
OFF
SURROUND
0
MENU
ENTER
RETURN
TEST
VOLUME
CH
1
Press YSP on the remote control to switch to
the operation mode of this unit.
YSP
2
Press MOVIE on the remote control to select
the movie sound field program.
8
■ Sports program
+10
CINEMA DSP
Select this sound field program when you play movie
sources, especially the ones encoded in Dolby Digital,
DTS or Dolby Surround. This program clearly reproduces
dialog and sound effects, thus creating a broad and
expansive cinematic space amid silence.
MOVIE
SPORTS
CH LEVEL
■ Movie program
TV VOL
Select this sound field program when you play sports
sources. This program densely concentrates the vocal
sound of the commentator in the center while broadening
the sound from the audience or the environment all around
your listening room.
1
Press YSP on the remote control to switch to
the operation mode of this unit.
YSP
■ Music program
Select this sound field program when you play music
sources. This program produces a vibrant atmosphere and
lets you feel as if you are seated in an actual rock or jazz
concert hall.
2
Press SPORTS on the remote control to
select the sports sound field program.
SPORTS
1
Press YSP on the remote control to switch to
the operation mode of this unit.
YSP
2
Press MUSIC on the remote control to select
the music sound field program.
MUSIC
7
50
0
USING SOUND FIELD PROGRAMS
Turning off CINEMA DSP programs
Turn off the CINEMA DSP programs if you want to enjoy
the original sound without the sound field program effect.
1
Press YSP on the remote control to switch to
the operation mode of this unit.
YSP
2
Adjusting CINEMA DSP levels
You can enjoy good quality sound with the factory preset
parameters. However, you can also adjust the effect level
of the CINEMA DSP programs relative to the level of the
direct sound so that each sound field program can reflect
your listening environment and your preference even more
accurately.
1
Press YSP on the remote control to switch to
the operation mode of this unit.
Press OFF on the remote control to turn off
the sound field programs.
YSP
OFF
+10
2
Press MUSIC, MOVIE or SPORTS on the
remote control to select the desired sound
field program.
MUSIC
7
3
MOVIE
or
8
SPORTS
or
0
Press
/
on the remote control.
DSP LEVEL is shown in the front panel display.
BASIC
OPERATION
VOL
4
Press / on the remote control to adjust
the effect level of the CINEMA DSP programs.
ENTER
Control range: –6 dB to +3 dB
• A larger value increases the effect level.
• A smaller value decreases the effect level.
English
51
USING THE VOLUME MODE
USING THE VOLUME MODE
The night listening modes are designed to improve listenability at lower volumes or at night. In addition, you can limit
the volume level of the TV so that it will not vary suddenly to a great extent whenever the contents being broadcast
change (i.e. due to commercials, etc.).
INPUTMODE
SLEEP
YSP
5BEAM
ST+3BEAM
3BEAM
1
2
3
STEREO
TARGET
4
5
6
MUSIC
MOVIE
VOL MODE
7
8
9
SPORTS
OFF
SURROUND
0
+10
CH LEVEL
CINEMA DSP
3
Press VOL MODE on the remote control
repeatedly to select NIGHT:CINEMA,
NIGHT:MUSIC, TV EQUAL VOL or NIGHT
OFF.
VOL MODE
9
MENU
ENTER
RETURN
TEST
NIGHT:CINEMA
NIGHT:MUSIC
1
Press YSP on the remote control to switch to
the operation mode of this unit.
YSP
2
Press VOL MODE on the remote control to
switch to the volume mode.
The NIGHT indicator lights up in the front panel
display.
VOL MODE
9
NIGHT
Lights up
52
TV EQUAL VOL
NIGHT OFF
• Select NIGHT:CINEMA when watching films to
reduce the dynamic range of film soundtracks and
make dialog easier to hear at lower volumes.
• Select NIGHT:MUSIC when listening to music
sources to preserve ease-of-listening for all sounds.
• Select TV EQUAL VOL when watching TV
programs.
• Select NIGHT OFF to turn off the night listening
modes.
USING THE VOLUME MODE
4
Press / on the remote control to adjust
the effect level of compression while
NIGHT:CINEMA, NIGHT:MUSIC or TV EQUAL
VOL is displayed.
ENTER
Effect.Lvl:MIN
Effect.Lvl:MID
Effect.Lvl:MAX
• Select Effect.Lvl:MIN for minimum compression.
• Select Effect.Lvl:MID for standard compression.
• Select Effect.Lvl:MAX for maximum
compression.
Note
BASIC
OPERATION
The volume mode settings are canceled if you press
STANDBY/ON on the front panel or on the remote control
or if you disconnect the power supply cable from the AC
wall outlet.
English
53
USING TRUBASS
USING TruBass
This unit can produce the perception of an improved low frequency performance with the aid of the SRS TruBass
technology, which improves bass even without a subwoofer and provides deeper, richer bass in the presence of a
subwoofer.
Note
The TruBass is not available when the target mode is selected as the beam mode (see page 43).
2
STANDBY/ON
DVD
POWER
POWER
AV
TV
VCR
STB
TV
INPUT1
TV
INPUT2
MACRO
INPUTMODE
SLEEP
Press
on the remote control repeatedly
to turn on SRS TruBass.
TruBass ON is shown in the front panel display.
AUX
YSP
1
Press
on the remote control.
The current setting (TruBass ON or TruBass OFF) is
shown in the front panel display.
TruBass ON
TruBass OFF
VOL
VOL
3
or
Press
on the remote control repeatedly
to turn off SRS TruBass.
TruBass OFF is shown in the front panel display.
VOL
TruBass ON
TruBass OFF
VOL
54
USING THE SLEEP TIMER
USING THE SLEEP TIMER
Use this feature to automatically set this unit to the standby mode after a specified time period. The sleep timer is useful
if you are going to sleep after a certain amount of time while this unit is still playing back a source.
Each time you press SLEEP on the remote control,
the front panel display changes as shown below.
Setting the sleep timer
INPUTMODE
SLEEP
SLEEP
YSP
5BEAM
ST+3BEAM
3BEAM
1
2
3
STEREO
UNIVERSAL
4
5
6
MUSIC
MOVIE
VOL MODE
7
8
9
SPORTS
OFF
SURROUND
0
+10
CH LEVEL
CINEMA DSP
MENU
ENTER
TEST
1
SLEEP
120min
SLEEP
90min
SLEEP
60min
SLEEP
30min
SLEEP
OFF
RETURN
2
Wait for a few seconds without operating this
unit to confirm the setting for the sleep timer.
The SLEEP indicator lights up in the front panel
display, indicating that the sleep timer is activated.
BASIC
OPERATION
Press SLEEP on the remote control
repeatedly to set the amount of time for the
sleep timer.
Choices: 120 min, 90 min, 60 min, 30 min, OFF
The SLEEP indicator in the front panel display
flashes while switching the amount of time for the
sleep timer.
SLEEP
SLEEP
Flashes
SLEEP
Lights up
English
55
USING THE SLEEP TIMER
Canceling the sleep timer
1
Press SLEEP on the remote control
repeatedly so that SLEEP OFF appears in the
front panel display.
SLEEP
VOL
SLEEP
2
OFF
Wait for a few seconds without operating this
unit to confirm the setting for the sleep timer.
The SLEEP indicator disappears from the front panel
display, indicating that the sleep timer is deactivated.
SLEEP
Disappears
Note
The previous setting for the sleep timer before you deactivate it is
stored in the system memory and automatically restored when
you make a new setting next time.
y
The sleep timer setting can also be deactivated if you press
STANDBY/ON on the front panel or on the remote control to set
this unit to the standby mode or unplug the power cable from the
AC outlet.
56
BASIC SETUP
BASIC SETUP
If you cannot run AUTO SETUP successfully or if an error occurs during the AUTO SETUP procedure, you can use
BASIC SETUP to individually set the parameters of this unit in the following order:
1) ROOM TYPE (Room type)
2) INSTALLED POSITION (Installed position of this unit)
3) ROOM SIZE (Room size)
y
• You can save the settings optimized by the AUTO SETUP procedure (see page 34). A set of settings optimized according to specific
conditions of your listening environment can be recalled later depending on the varying conditions of your listening environment (see
page 35).
• In order to fine-tune the listening environment parameters, as well as to make advanced settings for speaker positions, sound beams,
digital input and the OSD, see MANUAL SETUP (see page 63).
• Items with an asterisk (*) appearing next to them may be displayed differently on your screen depending on your individual settings.
Note
Each listening environment parameter must be set before the next parameter in order is set.
y
INPUTMODE
• The control buttons used for SET MENU are displayed on
the bottom of the screen.
• To return to the previous screen while using SET MENU,
press RETURN on the remote control.
• To resume cursor button operations after changing the
control area by pressing an input selector button, press
TEST on the remote control.
• To cancel the SET MENU screen, press MENU once
more.
• You can also perform the following operations in the front
panel display.
• If you press an input selector button during the SET
MENU operations, the cursor buttons become ineffective.
In this case, press TEST once.
SLEEP
YSP
5BEAM
ST+3BEAM
3BEAM
1
2
3
STEREO
TARGET
4
5
6
MUSIC
MOVIE
VOL MODE
7
8
9
SPORTS
OFF
SURROUND
0
CH LEVEL
+10
CINEMA DSP
MENU
ENTER
RETURN
TEST
3
■ Displaying the SET MENU screen
ADVANCED
OPERATION
1
Press
/
to select BASIC SETUP and
then press ENTER.
The following screen appears on your TV.
Press YSP on the remote control to switch to
the operation mode of this unit.
ENTER
ENTER
YSP
2
Press MENU on the remote control.
The SET MENU screen appears on your TV.
;BASIC SETUP
SET MENU
MENU
.;MEMORY
;AUTO SETUP
;BASIC SETUP
;MANUAL SETUP
.1 ROOM TYPE ?
2
3
4
PUSH [ENTER] Key.
p
English
p
[]/[]:Up/Down
[ENTER]:Enter
57
BASIC SETUP
■ ROOM TYPE (Room type)
4
y
If the shape of your listening room is irregular, select the
shape that most closely resembles your room.
In Example 1, the shape that best describes the listening
room is RECTANGLE. In Example 2, it is SQUARE.
Check that the following screen is displayed
on your TV.
If this screen is not displayed, repeat steps 1 to 3.
Example 1:
Rectangular
room
;BASIC SETUP
Example 2:
Square
room
.1 ROOM TYPE ?
2
3
4
PUSH [ENTER] Key.
5
Press ENTER.
7
ENTER
6
Press / to switch between the SQUARE
and RECTANGLE selection screens and then
press ENTER to select the desired setting.
Press ENTER to confirm the setting for the
room type.
The following screen appears in the front panel
display.
;BASIC SETUP
ENTER
LE.E* SQUARE
EQ. 2 INSTALLED POSITION ?
LE.E3
.E4
PUSH [ENTER] Key.
1 ROOM TYPE ?
SQUARE
ENTER
[p]/[p]:Select
[ENTER]:Enter
1 ROOM TYPE ?
RECTANGLE
[p ]/[p]:Select
[ENTER]:Enter
• Select SQUARE if the shape of your listening
room is nearest to a square.
• Select RECTANGLE if the shape of your listening
room is nearest to a rectangle.
58
BASIC SETUP
■ INSTALLED POSITION
(Installed position of this unit)
8
Check that the following screen is displayed
on your TV.
If this screen is not displayed, make settings for
ROOM TYPE.
If RECTANGLE is selected for ROOM TYPE
Select WIDE LEFT, WIDE CENTER, WIDE
RIGHT, CORNER RIGHT, CORNER LEFT,
NARROW LEFT, NARROW CENTER or
NARROW RIGHT that best matches the installed
position of this unit in your listening room.
2 INSTALLED POSITION ?
;BASIC SETUP
ENTER
ENTER
LE.E* SQUARE
EQ. 2 INSTALLED POSITION ?
LE.E3
.E4
-
WIDE
CENTER
[p]/[p]:Select
[ENTER]:Enter
PUSH [ENTER] Key.
9
Press ENTER.
If you selected SQUARE for ROOM TYPE (see
page 58), four different installed position types in a
square room are displayed.
If you selected RECTANGLE, eight different
installed position types in a rectangular room are
displayed.
If SQUARE is selected for ROOM TYPE
Select LEFT, CENTER, RIGHT or CORNER that
best matches the installed position of this unit in your
listening room.
2 INSTALLED POSITION ?
ENTER
ENTER
-
CENTER
WIDE LEFT
(Wide wall left)
WIDE CENTER
(Wide wall center)
WIDE RIGHT
(Wide wall right)
CORNER RIGHT
(Corner right)
[p]/[p]:Select
[ENTER]:Enter
CENTER
(Center)
CORNER LEFT
(Corner left)
ADVANCED
OPERATION
LEFT
(Left)
NARROW LEFT
(Narrow wall left)
NARROW CENTER
(Narrow wall center)
NARROW RIGHT
(Narrow wall right)
English
CORNER
(Corner left or right)
RIGHT
(Right)
59
BASIC SETUP
10
■ ROOM SIZE (Room size)
Press / to select the installed position
type that best suits the installed position of
this unit in your listening room and then
press ENTER.
The following screen appears in the front panel
display.
11
Check that the following screen is displayed
on your TV.
If this screen is not displayed, make settings for
INSTALLED POSITION.
;BASIC SETUP
LE.E* SQUARE
EQ.>* CENTER
LE.E3 ROOM SIZE ?
LE.E4
ENTER
ENTERENTER
PUSH [ENTER] Key.
12
;BASIC SETUP
LE.E* SQUARE
EQ.>* CENTER
LE.E3 ROOM SIZE ?
LE.E4
Press ENTER.
Three different room sizes (SMALL, MID or
LARGE) are displayed for both SQUARE and
RECTANGLE.
If SQUARE is selected for ROOM TYPE
PUSH [ENTER] Key.
3 ROOM SIZE ?
.
ENTER
ENTER
. + -- .
MID
5.0m
.
[p]/[p]:Select
[ENTER]:Enter
3.8 m (13 ft)
SMALL
(Small)
3.8 m (13 ft)
5.0 m (17 ft)
MID
(Medium)
5.0 m (17 ft)
5.8 m (19 ft)
LARGE
(Large)
60
5.8 m (19 ft)
BASIC SETUP
If RECTANGLE is selected for ROOM TYPE
14
3 ROOM SIZE ?
.
ENTER
. --- + -- - 5.8m .
MID
-
ENTER
■ SETUP OK (Confirming settings)
4.2m
.
Check that the following screen is displayed
on your TV.
If this screen is not displayed, make settings for
ROOM SIZE.
[p]/[p]:Select
[ENTER]:Enter
;BASIC SETUP
LE.E*
EQ..*
LE.E*
. 4
3.4 m (11 ft)
SQUARE
CENTER
MID
SETUP OK ?
PUSH [ENTER] Key.
SMALL
(Small)
4.2 m (14 ft)
15
4.2 m (14 ft)
Press ENTER.
The following screen appears in the front panel
display.
4 SETUP OK?
MID
(Medium)
5.8 m (19 ft)
DATA SETUP
ENTER
p YES
NO
[p]/[ p]:Select
[ENTER]:Enter
5.0 m (17 ft)
LARGE
(Large)
ADVANCED
OPERATION
13
6.8 m (23 ft)
Press / to select the room size that best
suits your listening room and then press
ENTER.
ENTER
ENTER
ENTER
English
61
BASIC SETUP
16
Press / to select YES or NO and then
press ENTER.
ENTER
ENTER
• Select YES to register the settings if they are
satisfactory. The following screen appears, and
your BASIC SETUP settings are registered.
4 SETUP OK?
Data Setting !
Please wait.
• Select NO to cancel the settings and return to the
initial SET MENU screen.
SET MENU
;MEMORY
;AUTO SETUP
.;BASIC SETUP
;MANUAL SETUP
17
p
p
[]/[]:Up/Down
[ENTER]:Enter
Press MENU to complete the BASIC SETUP
procedure.
The SET MENU display disappears from your TV
screen.
MENU
This completes the parameter settings for BASIC SETUP.
To select a playback source and enjoy surround sound on
this unit, see “PLAYBACK” on page 37.
62
MANUAL SETUP
MANUAL SETUP
To achieve the best quality surround sound, you can use MANUAL SETUP to fine-tune the listening environment
parameters, as well as to make advanced settings for speaker positions, sound beams, digital input and the OSD. Change
the initial settings (indicated in bold under each parameter) to reflect the needs of your own listening environment.
y
• You can save the settings optimized by the AUTO SETUP procedure (see page 34). A set of settings optimized according to specific
conditions of your listening environment can be recalled later depending on the varying conditions of your listening environment (see
page 35).
• Most of the parameters in SOUND MENU and BEAM MENU are automatically set when you run AUTO SETUP (see page 26). Use
SOUND MENU and BEAM MENU to make additional adjustments.
• BEAM MENU allows you to make settings for the surround sound effects normally available in the speaker settings menu.
• Make settings for the parameters in BEAM MENU first before you make settings for the parameters in SOUND MENU, INPUT
MENU and DISPLAY MENU.
SOUND MENU
Use to manually adjust various parameters related to the sound output.
Item
Features
Page
TONE CONTROL
Adjusts the output level of high-frequency or low-frequency sound.
69
BEAM LEVEL
Adjusts the output level of each beam.
69
SUBWOOFER SET
Adjusts the various subwoofer settings.
70
MUTE LEVEL
Adjusts the muting level.
70
AUDIO DELAY
Adjusts audio delay.
70
ROOM EQ
Adjusts the tonal quality of the listening room.
70
DD/DTS Dynamic Range
Adjusts the dynamic range of Dolby Digital or DTS signals.
71
BEAM MENU
Use to manually adjust various parameters related to the sound beam output.
Item
Features
Page
Adjusts listening room and listening position settings.
65
BEAM ADJUSTMENT
Adjusts various beam settings.
66
IMAGE LOCATION
Adjusts the position of the front left and right speakers.
68
INPUT MENU
Use to manually adjust various parameters related to the audio and video input.
Item
Features
Page
INPUT ASSIGNMENT
Assigns jacks according to the component to be used.
71
INPUT MODE
Selects the initial input of the source.
72
INPUT TRIM
Adjusts the input level of the source.
72
INPUT RENAME
Renames the displayed input source.
72
ADVANCED
OPERATION
SETTING PARAMETERS
DISPLAY MENU
Use to manually adjust various parameters related to the display.
Item
Features
Page
Adjusts the brightness of the display.
73
OSD SET
Adjusts the display position and the background color of the OSD.
74
UNIT SET
Changes the display unit of measurement.
74
English
DIMMER SET
63
MANUAL SETUP
Using MANUAL SETUP
3
Use the remote control to access and adjust each
parameter.
INPUTMODE
Press
/
to select MANUAL SETUP and
then press ENTER.
The following screen appears on your TV.
SLEEP
YSP
5BEAM
ST+3BEAM
3BEAM
1
2
3
STEREO
TARGET
ENTER
4
5
6
MUSIC
MOVIE
VOL MODE
7
8
9
SPORTS
OFF
SURROUND
0
CH LEVEL
ENTER
+10
CINEMA DSP
MENU
ENTER
RETURN
TEST
;MANUAL SETUP
.1
2
3
4
SOUND MENU
BEAM MENU
INPUT MENU
DISPLAY MENU
p
p
[]/[]:Up/Down
[ENTER]:Enter
y
You can adjust the SET MENU parameters while the unit is
reproducing sound.
1
4
Press YSP on the remote control to switch to
the operation mode of this unit.
YSP
2
Press
/
to select a sub menu and then
press ENTER.
ENTER
ENTER
Press MENU on the remote control.
The SET MENU screen appears on your TV.
5
SET MENU
MENU
Press
/
/ /
each parameter.
and ENTER to configure
.;MEMORY
;AUTO SETUP
;BASIC SETUP
;MANUAL SETUP
p
p
[]/[]:Up/Down
[ENTER]:Enter
ENTER
y
• The control buttons used for SET MENU are displayed on
the bottom of the screen.
• To return to the previous screen while using SET MENU,
press RETURN on the remote control.
• To resume cursor button operations after changing the
control area by pressing an input selector button, press
TEST on the remote control.
• To cancel the SET MENU screen, press MENU once
more.
• You can also perform the following operations in the front
panel display.
• If you press an input selector button during the SET
MENU operations, the cursor buttons become ineffective.
In this case, press TEST once.
64
6
Press MENU to exit.
The OSD disappears from your TV screen.
MENU
MANUAL SETUP
BEAM MENU
Use to manually adjust various parameters related to the
sound beam output.
SET MENU → MANUAL SETUP → BEAM MENU
• Select FLAT TO WALL if this unit is installed in
parallel with the wall in your listening room. Adjust the
width and length of your listening room as well as the
distance of the listening position from this unit and the
distance of the center of this unit from the left wall.
Listening position
from the left wall
2 BEAM MENU
Listening position
from the unit
p
■ SETTING PARAMETERS
(Setting parameters)
Use to set the position of this unit in your listening room
and the distance of this unit from the listening position.
When you make settings for each parameter, other related
parameters are automatically adjusted to best match your
listening environment.
Note
If you make adjustments in SETTING PARAMETERS, the beam
optimization settings made in the AUTO SETUP procedure will
be lost. If you want to keep the beam optimization settings made
in the AUTO SETUP and make further adjustments, adjust
settings in BEAM ADJUSTMENT first (see page 66).
Room length
Room width
Choices for the room width and length:
2.0 m to 12.0 m (6.5 ft to 40.0 ft)
Choices for the listening position from this unit:
2.0 m to 9.0 m (6.5 ft to 30.0 ft)
Choices for the listening position from the left wall:
0.6 m to 11.4 m (2.0 ft to 38.0 ft)
A)SETTING PARAMETERS 2/3
Room width and length
12.0m
12.0m
p
p
p
.A)SETTING PARAMETERS
B)BEAM ADJUSTMENT
C)IMAGE LOCATION
[]/[]:Up/Down
[SELECT]:Enter
p
p
[]/[]:Up/Down[ ]/[ ]:Sel
[ENTER]:Return
A)SETTING PARAMETER1/3
.INSTALLED POSITION
;;;;;FLAT TO WALL
A)SETTING PARAMETERS 3/3
p
[]/[]:Up/Down[ ]/[ ]:Sel
[ENTER]:Return
Listening position from the
unit and the left wall
12.0m
ADVANCED
OPERATION
p
[]/[]:Up/Down[ ]/[ ]:Sel
[ENTER]:Return
p
FLAT TO WALL
12.0m
p
INSTALLED POSITION
(Installed position of this unit)
Use to adjust the installed position of this unit.
Choices: FLAT TO WALL (Parallel to wall installation),
ANGLE TO WALL OR CORNER
(Corner installation)
p
p
p
p
ANGLE TO WALL
OR CORNER
English
65
MANUAL SETUP
• Select ANGLE TO WALL OR CORNER if this unit is
installed in the corner in your listening room. Adjust
the width and length of your listening room as well as
the distance of the listening position from this unit and
the distance of the center of this unit from the left wall.
Use to manually adjust the various speaker beam angles.
We recommend that you select 5 beam mode before
adjusting these parameters.
Notes
Listening position
from the unit
• When INSTALLED POSITION is adjusted in BASIC SETUP
(see page 59) or MANUAL SETUP (see page 65), the factory
default value is automatically set for this parameter except when
FOCAL LENGTH is set to CENTER (see page 67).
• Depending on the beam mode settings (see page 40), some
speaker positions may not be available for selection. In this
case, “– –” is displayed. When using the stereo plus 3 beam
mode, set the surround left and right signals to be output from
the front left and right speakers.
Room width
B)BEAM ADJUSTMENT
Room length
12.0m
[]/[]:Up/Down
[SELECT]:Enter
p
A)SETTING PARAMETERS 2/3
.a)HORIZONTAL ANGLE
b)BEAM TRAVEL LENGTH
c)FOCAL LENGTH
d)TREBLE GAIN
p
Choices for the room width and length:
2.0 m to 12.0 m (6.5 ft to 40.0 ft)
Choices for the listening position from this unit:
2.0 m to 9.0 m (6.5 ft to 30.0 ft)
Choices for the listening position from the left wall:
0.6 m to 11.4 m (2.0 ft to 38.0 ft)
Room width and length
■ BEAM ADJUSTMENT (Beam adjustment)
HORIZONTAL ANGLE (Horizontal angle)
Use to adjust the horizontal angle of beams for each
speaker. By adjusting the horizontal angle of the beams,
you can optimize the sound beam paths. A test tone is
automatically output.
12.0m
p
p
p
p
[]/[]:Up/Down[ ]/[ ]:Sel
[ENTER]:Return
(−)
(+)
(+)
(−)
A)SETTING PARAMETERS 3/3
Listening position from
the unit and the left wall
12.0m
p
p
[]/[]:Up/Down[ ]/[ ]:Sel
[ENTER]:Return
Note
When you set the INSTALLED POSITION parameter in BASIC
SETUP (see page 59) or MANUAL SETUP (see page 65), the
parameters newly set for the width and length of your listening
room are automatically set as the factory default value.
Choices: L90° to R90°
Adjust towards L (left) to move the direction of the output
to the left and adjust towards R (right) to move it to the
right.
a)HORIZONTAL ANGLE
1/5
3BEAM
Front L
L60deg
L90
R90
*
0(deg)
p
p
p
p
66
p
p
[]/[]:Up/Down[ ]/[ ]:Sel
[ENTER]:Return
MANUAL SETUP
BEAM TRAVEL LENGTH (Beam travel length)
Use to set the distance that sound beams travel after being
output and reflected off the wall until they arrive at the
listening position for each speaker.
The lines in the illustration below indicate the distance.
Choices: 0.3 m to 24.0 m (1.0 ft to 80.0 ft)
• Front L adjusts the distance the front left speaker
sound beams travel.
• Front R adjusts the distance the front right speaker
sound beams travel.
• Center adjusts the distance the center speaker sound
beams travel.
• Surround L adjusts the distance the surround left
speaker sound beams travel.
• Surround R adjusts the distance the surround right
speaker sound beams travel.
b)BEAM TRAVEL 3Beam
LENGTH
FOCAL LENGTH (Focal length)
Use to set the distance from the front of this unit to the
focal point of output for each speaker.
Choices: –1.0 m to +13.0 m (–3.5 ft to +43.5 ft)
Adjust towards – (minus) to move the focus outward and
adjust towards + (plus) to move the focus towards the
normal position.
• Front L adjusts the focal length for the front left sound
beams.
• Front R adjusts the focal length for the front right
sound beams.
• Center adjusts the focal length for the center sound
beams. Initial setting: –0.5 m (–1.5 ft)
• Surround L adjusts the focal length for the surround
left sound beams.
• Surround R adjusts the focal length for the surround
right sound beams.
y
We recommend that you use the initial setting (–0.5 m) for the
center speaker.
p
p
p
p
[]/[]:Up/Down[ ]/[ ]:Sel
[ENTER]:Return
c)FOCAL LENGTH
3Beam
. Front L;;;;;;;+6.0m
Front R;;;;;;;+6.0m
Center;;;;;;;;-1.0m
Surround L;;;;+13.0m
Surround R;;;;+13.0m
p
p
. Front L;;;;;;;7.1m
Front R;;;;;;;7.1m
Center;;;;;;;;3.0m
Surround L;;;;10.0m
Surround R;;;;10.0m
p
p
[]/[]:Up/Down[ ]/[ ]:Sel
[ENTER]:Return
ADVANCED
OPERATION
English
67
MANUAL SETUP
TREBLE GAIN (Treble gain)
Use to adjust the high frequency output level of each
speaker.
y
If the reflection point of the front left and right or surround left
and right sound beams is a curtain or other acoustically absorbent
surface, you can achieve more effective surround sound by
increasing the treble level for those sound beams.
■ IMAGE LOCATION (Image location)
Use to adjust the direction from which the front left and
right speaker sound is heard by directing these audio
signals so that they are also output from the center
speaker.
Use this feature to redirect audio signals if the sound
coming from the left and right speakers seems unnatural,
such as when your listening position is not the center of
your listening room.
You can only adjust this parameter when 3 beam mode or
5 beam mode is selected as the beam mode (see page 42).
Choices: ON, OFF
Setting range: 0% to 95%
Initial setting: 0%
C)IMAGE LOCATION
. OFF
L
C
) ON
R
p
LEFT;;;;;;;;;;0%
RIGHT;;;;;;;;;0%
p
p
p
[]/[]:Up/Down[ ]/[ ]:Sel
[ENTER]:Return
p
Choices: –12.0 dB to +12.0 dB
Initial setting: 0 dB
• FL adjusts the high frequency output level of the front
left speaker.
• FR adjusts the high frequency output level of the front
right speaker.
• C adjusts the high frequency output level of the center
speaker.
• SL adjusts the high frequency output level of the
surround left speaker.
• SR adjusts the high frequency output level of the
surround right speaker.
LEFT (Left)
Adjusts audio signals towards the left.
The higher the percentage, the louder the output from the
center.
Without adjustment
With the front left
speaker adjusted
d)TREBLE GAIN
. Surround L;;;;;0dB
Surround R;;;;;0dB
Center;;;;;;;;;0dB
Front L;;;;;;;;0dB
Front R;;;;;;;;0dB
+
+
+
+
+
p
p
-
p
p
[]/[]:Up/Down[ ]/[ ]:Sel
[ENTER]:Return
RIGHT (Right)
Adjusts audio signals towards the right.
The higher the percentage, the louder the output from the
center.
Without adjustment
68
With the front right
speaker adjusted
MANUAL SETUP
■ BEAM LEVEL (Beam level)
SOUND MENU
Use to manually adjust various parameters related to the
sound output.
SET MENU → MANUAL SETUP → SOUND MENU
1 SOUND MENU
. A)TONE CONTROL
B)BEAM LEVEL
C)SUBWOOFER SET
D)MUTE LEVEL
E)AUDIO DELAY
F)ROOM EQ
G)DD/DTS Dynamic Range
p
p
[]/[]:Up/Down
[ENTER]:Enter
■ TONE CONTROL (Tone control)
You can adjust the tonal quality of your speakers.
Use to manually balance the speaker levels between the
front left or surround left speakers and each speaker
selected.
When setting the front right, center or surround left
speakers or the subwoofer, the test tone is output from the
front left speakers and the selected speaker position.
When setting the surround right speaker, the test tone is
output alternately from the surround left and right
speakers.
The factory default value is automatically set for this
parameter depending on the parameters set in AUTO
SETUP, BASIC SETUP or ROOM EQ in MANUAL
SETUP.
Depending on the beam mode settings, some channels
may not be available for selection. In this case, NONE is
displayed.
A)TONE CONTROL
BASS;;;;;;0dB
p
p
p
p
[]/[]:Up/Down[ ]/[ ]:Sel
[ENTER]:Return
B)BEAM LEVEL
TREBLE (Treble)
Use to adjust the high frequency response.
Choices: –12 dB to +12 dB
Initial setting: 0 dB
BASS (Bass)
Use to adjust the low frequency response.
Choices: –12 dB to +12 dB
Initial setting: 0 dB
p
p
- +
.FR
C
SL
SR
SWFR
*OUT : FL )FR
*MODE: 5 BEAM
p
[]/[]:Up/Down[ ]/[ ]:Sel
[ENTER]:Return
p
+
. TREBLE;;;;0dB -
• FR adjusts the balance of the front left and front right
speakers.
• C adjusts the balance of the front left and center
speakers.
• SL adjusts the balance of the front left and surround
left speakers.
• SR adjusts the balance of the surround left and
surround right speakers.
• SWFR adjusts the balance of the front left speaker and
subwoofer.
ADVANCED
OPERATION
English
69
01EN_YSP-800_UB_EN.book Page 70 Wednesday, March 12, 2008 4:06 PM
MANUAL SETUP
■ SUBWOOFER SET (Subwoofer set)
Use to manually adjust various subwoofer settings.
C)SUBWOOFERSET
.BASS OUT;;;;;FRONT
CROSS OVER;;;120Hz
LFE LEVEL;;;;-20dB
DISTANCE;;;;;15.0m
Use to adjust how much the mute function reduces the
volume level.
Choices: MUTE, –20 dB
• Select MUTE to completely halt all sound output.
• Select –20 dB to reduce the current volume level by 20
dB.
p
p
■ MUTE LEVEL (Muting level)
p
p
[]/[]:Up/Down[ ]/[ ]:Select
[ENTER]:Return
D)MUTE LEVEL
■ AUDIO DELAY (Audio delay)
Use to delay the sound output and synchronize it with the
video image. This may be necessary when using certain
LCD monitors or projectors.
Choices: 0 to 160 msec
E)AUDIO DELAY
AUDIO DELAY;;;30msec
p
[ ]/[ ]:Select
[ENTER]:Return
■ ROOM EQ (Room equalizer)
Use to change the tonal qualities of your listening room
when the unit is mounted on the wall.
Choices: MOUNT (Mount),
REFLECTING (Reflectivity type)
F)ROOM EQ
.MOUNTING;;;;;WALL/SHELF
REFLECTING;;;NORMAL/HI ECHO
p
p
[]/[]:Up/Down[ ]/[ ]:Sel
[ENTER]:Return
p
DISTANCE (Distance)
Select to adjust the distance of the subwoofer from the
listening position.
Choices: 0.3 to 15.0 m (1 to 50 ft)
Initial setting: 3.0 m (10 ft)
p
-20dB
[ ]/[ ]:Select
[ENTER]:Return
p
LFE LEVEL (Low-frequency effect level)
Select to adjust the output level of the LFE (low-frequency
effect) channel according to the capacity of your
subwoofer. The LFE channel carries low-frequency
special effects which are only added to certain scenes.
This setting is effective only when this unit decodes Dolby
Digital or DTS signals.
Choices: –20 to 0 dB
)MUTE
p
CROSS OVER (Cross over)
When BASS OUT is set to SWFR, you can use this
feature to select a cross-over (cut-off) frequency for all
low-frequency signals. All frequencies below the selected
frequency will be sent to the subwoofer speaker position.
Choices: 80Hz, 100Hz, 120Hz
p
BASS OUT (Bass out)
Low-frequency (bass) signals can be directed to the
subwoofer or the front left and right speaker positions.
This setting also determines the routing of LFE (lowfrequency effect) signals found in Dolby Digital or DTS
sources.
Choices: SWFR (subwoofer), FRONT
• Select SWFR if you connect a subwoofer. LFE and
low-frequency signals from other channels are directed
to the subwoofer according to the speaker settings.
• Select FRONT if you do not use a subwoofer. LFE and
low-frequency signals from other channels are directed
to the front speakers according to the speaker settings
(even if you have previously set the front speakers to
SMALL).
MOUNT (Mount)
Use to enhance medium to low range sounds.
Choices: WALL (Wall mount), SHELF (Shelf mount)
• Select WALL if this unit is mounted on the wall in your
listening room.
• Select SHELF if this unit is mounted on the shelf in
your listening room.
REFLECTING (Reflectivity type)
Use to select the reflectivity of your listening room.
Choices: NORMAL (Normal), HI ECHO (High echo)
• Select NORMAL if your listening room has a normal
reflectivity.
• Select HI ECHO if your listening room has highly
reflective surfaces such as concrete walls.
70
Black process 45.0° 240.0 LPI
MANUAL SETUP
■ DD/DTS Dynamic Range
(Dynamic range of Dolby Digital and
DTS signals)
Use to select the amount of dynamic range compression to
be applied to the speakers. This setting is effective only
when the unit is decoding Dolby Digital and DTS signals.
Dynamic range is the difference between the smallest
sound that can be heard above the noise of the equipment
and the biggest sound that can be heard without distortion.
Choices: MIN (minimum), STD (standard),
MAX (maximum)
INPUT MENU
Use to manually adjust various parameters related to the
audio and video input.
SET MENU → MANUAL SETUP → INPUT MENU
3 INPUT MENU
.A)INPUT
B)INPUT
C)INPUT
D)INPUT
ASSIGNMENT
MODE
TRIM
RENAME
p
p
[]/[]:Up/Down
[ENTER]:Enter
G)DD/DTS Dynamic Range
[ ]/[ ]:Select
[ENTER]:Retern
Select to adjust the speaker compression.
• Select MIN for listening to sources at low volume
levels.
• Select STD for general use.
• Select MAX for feature films.
■ INPUT ASSIGNMENT (Input assignment)
Use to assign the optical and coaxial digital input jacks of
this unit to other components if the initial settings of this
unit do not correspond to your needs. By assigning other
components to the input jacks on this unit, you can display
the name of the connected component in the front panel
display and OSD, and operate the component with the
input selector button of the same name. If you connect a
component to the input jacks of this unit and do not assign
it, the default component name for that input jack is
displayed in the front panel and OSD when selected.
• Select OPTICAL IN (1) to assign components to the
TV OPTICAL IN jack of this unit.
Choices: TV, VCR
• Select OPTICAL IN (2) to assign components to the
AUX OPTICAL IN jack of this unit.
Choices: AUX, DVD
A)INPUT ASSIGNMENT 1/2
(.
(.
(.
(.
OPTICAL IN
(1);;;;; TV
(1);;;;(
TV
(2);;;;; AUX
(1);;;;( AUX
)
)
p
ADVANCED
OPERATION
p
p
[]/[]:Up/Down[ ]/[ ]:Sel
[ENTER]:Return
• Select COAX IN (3) to assign components to the
COAXIAL IN jack of this unit.
Choices: DVD, AUX
A)INPUT ASSIGNMENT 2/2
COAX IN
(. (3);;;;; DVD
(. (1);;;;( DVD
(.
)
p
p
p
p
STD )MAX
p
MIN
p
p
[]/[]:Up/Down[ ]/[ ]:Sel
[ENTER]:Return
English
71
MANUAL SETUP
■ INPUT MODE (Input mode)
■ INPUT RENAME (Input rename)
Use to designate the input mode for the input sources
connected to the DIGITAL INPUT jacks when you turn on
the power of this unit. For information on the types of
audio signals that can be output by this unit, see “Surround
modes and recommended sources” on page 44.
Choices: AUTO, LAST
Use to change the name of the input source in the OSD
and the front panel display. Press an input selector button
(TV, STB, DVD, VCR, or AUX) to select the component
you want to change the name for and then perform the
following procedure.
D)INPUTRENAME
B)INPUT MODE
AUX ->
p
[ ]/[ ]:Position
[]/[]:Character
[ENTER]:Return
p
p
[ ]/[ ]:Select
[ENTER]:Retern
• Select AUTO to allow this unit to automatically detect
the type of input signal and select the appropriate input
mode.
• Select LAST to set this unit to automatically select the
last input mode used for that input source. If the type of
input signal is different from the setting, no sounds will
be produced.
■ INPUT TRIM (Input trim)
1
p
p
AUX
LAST
p
)AUTO
Press TEST on the remote control.
TEST
2
Use to adjust the input level of the input source.
Press / to place the _ (underbar) under
the space or the character you want to edit.
The _ (underbar) flashes.
C)INPUT TRIM
TV
ANALOG;;;;;-3.0dB
OPTICAL;;;;-3.0dB
VCR ANALOG;;;;;-3.0dB
AUX OPTICAL;;;;-3.0dB
DVD COAXIAL;;;;-3.0dB
p
ENTER
p
(.
(.
(.
(.
(.
p
p
[]/[]:Up/Down[ ]/[ ]:Sel
[ENTER]:Return
• Select TV ANALOG to adjust the level of audio and
video signals input at the TV/STB analog audio input
jacks of this unit.
Control range: –6.0 dB to 0.0 dB
Initial setting: –3.0 dB
• Select TV OPTICAL to adjust the level of audio and
video signals input at the TV OPTICAL IN jack of this
unit.
Control range: –6.0 dB to 0.0 dB
Initial setting: –3.0 dB
• Select VCR ANALOG to adjust the level of audio and
video signals input at the VCR analog audio input
jacks of this unit.
Control range: –6.0 dB to 0.0 dB
Initial setting: –3.0 dB
• Select AUX OPTICAL to adjust the level of audio and
video signals input at the AUX OPTICAL IN jack of
this unit.
Control range: –6.0 dB to 0.0 dB
Initial setting: –3.0 dB
• Select DVD COAXIAL to adjust the level of audio and
video signals input at the COAXIAL IN jack of this
unit.
Control range: –6.0 dB to 0.0 dB
Initial setting: –3.0 dB
72
3
Press
/
to select the desired character.
• You can use up to 8 characters for each input.
• Press
to change the character in the following
order or press
to go in the reverse order:
A to Z, a space, 0 to 9, a space, a to z, a space, #, *,
+, etc.
ENTER
MANUAL SETUP
4
Repeat steps 1 to 3 to rename each input.
5
Press ENTER to exit.
The new names are registered, and the display returns
to the previous screen.
DISPLAY MENU
Use to manually adjust various parameters related to the
display.
SET MENU → MANUAL SETUP → OPTION MENU
4 DISPLAY MENU
p
p
■ DIMMER SET (Dimmer settings)
Use to adjust the brightness of the front panel display.
A)DIMMER SET
.STANDARD DIMMER;;;OFF
AUTO DIMMER;;;;;;;OFF
p
p
p
[]/[]:Up/Down[ ]/[ ]:Sel
[ENTER]:Return
p
ENTER
.A)DIMMER SET
B)OSD SET
C)UNIT SET
[]/[]:Up/Down
[ENTER]:Enter
STANDARD DIMMER (Standard dimmer)
Use to adjust the brightness of the front panel display
when you operate this unit by using the control buttons on
the front panel or on the remote control.
Choices: –2, –1, OFF
AUTO DIMMER (Auto dimmer)
If no operation is performed for a specified period, the
front panel display dims. Use to adjust the brightness of
the front panel display in this case.
Choices: DISPLAY OFF, –3 to –1 (based on the
STANDARD DIMMER setting), OFF
ADVANCED
OPERATION
English
73
MANUAL SETUP
■ OSD SET (OSD settings)
Use to adjust the display position and the background
color of the OSD.
B)OSD SET
.OSD SHIFT;;;;;;;;0
OSD BACK COLOR;;;BLUE
p
p
p
p
[]/[]:Up/Down[ ]/[ ]:Sel
[ENTER]:Return
OSD SHIFT (OSD shift)
Use to adjust the vertical position of the OSD. Adjust
towards the – (minus) direction to raise the position of the
OSD, and adjust towards the + (plus) direction to lower it.
Choices: –5 to +5
Initial setting: 0
OSD BACK COLOR (OSD background color)
Use to select the background color of the OSD.
Choices: BLUE, GRAY
■ UNIT SET (Unit settings)
(U.S.A. and Canada models only)
Use this to change the display unit of measurement.
Choices: METERS, FEET
C)UNIT SET
)METERS
p
FEET
p
[ ]/[ ]:Select
[ENTER]:Retern
• Select METERS to input speaker distances in meters.
• Select FEET to input speaker distances in feet.
74
ADJUSTING SYSTEM PARAMETERS
ADJUSTING SYSTEM PARAMETERS
Setting the maximum volume level
1
You can set the maximum volume level so that this unit
will not output sound beyond the limited volume level.
Press STANDBY/ON on the front panel or on
the remote control to turn off the power of
this unit.
or
STANDBY/ON
Front panel
2
INPUT
VOLUME
+
STANDBY/ON
STANDBY/ON
DVD
POWER
POWER
AV
TV
VCR
STB
TV
INPUT1
TV
INPUT2
MACRO
INPUTMODE
SLEEP
Remote control
Press and hold INPUT on the front panel and
then press STANDBY/ON on the front panel
to turn on the power of this unit.
MAX VOLUME SET is shown in the front panel
display.
INPUT
STANDBY/ON
AUX
VOL
MAX VOLUME SET
YSP
5BEAM
ST+3BEAM
3BEAM
1
2
3
STEREO
TARGET
4
5
6
MUSIC
MOVIE
VOL MODE
7
8
9
SPORTS
OFF
SURROUND
0
CH LEVEL
Release INPUT on the front panel.
+10
CINEMA DSP
INPUT
MENU
ADVANCED
OPERATION
4
ENTER
TEST
3
Press ENTER on the front panel.
RETURN
ENTER
English
75
ADJUSTING SYSTEM PARAMETERS
5
Press
level.
/
to adjust the maximum volume
Protecting the current settings
You can protect the current settings from being
accidentally erased or unwantedly changed.
1
Repeat steps 1 to 3 in “Setting the maximum
volume level” on page 75.
2
Press
/
on the remote control so that
MEMORY PROTECT is shown in the front
panel display.
ENTER
Control range: 0 dB to –99.0 dB
Control step: 1 dB
6
Press STANDBY/ON on the front panel or on
the remote control to set this unit to the
standby mode.
ENTER
or
STANDBY/ON
Front panel
Remote control
The new setting for the maximum volume level will
be activated when you turn on the power of this unit
next time.
VOL
MEMORY PROTECT
3
Press ENTER.
ENTER
76
ADJUSTING SYSTEM PARAMETERS
4
Press / to switch between PROTECT: ON
and PROTECT: OFF.
Initializing the current settings
You can reset all of the parameters of this unit to the
factory presets. This procedure completely resets ALL the
parameters in SET MENU.
Note
ENTER
After performing the following procedure you must reset the
ROOM TYPE, SP POSITION and ROOM SIZE parameters to
match your surround sound environment.
1
Repeat steps 1 to 3 in “Setting the maximum
volume level” on page 75.
2
Press
/
on the remote control so that
FACTORY PRESET is shown in the front
panel display.
VOL
PROTECT: ON
VOL
PROTECT: OFF
ENTER
• Select PROTECT: ON to activate the protection
feature.
• Select PROTECT: OFF to deactivate the protection
feature.
5
Press STANDBY/ON on the front panel or on
the remote control to set this unit to the
standby mode.
VOL
FACTORY PRESET
or
3
STANDBY/ON
Front panel
Press ENTER.
Remote control
ADVANCED
OPERATION
The new setting will be activated when you turn on
the power of this unit next time.
ENTER
English
77
ADJUSTING SYSTEM PARAMETERS
4
Press / to switch between PRESET:
RESET and PRESET: CANCEL.
Adjusting the audio balance
You can adjust the sound beam output level of each
speaker by using the test tone or the audio output being
played back in each beam mode to achieve a more true-tolife surround sound experience.
ENTER
Notes
VOL
PRESET: RESET
• All the speaker levels cannot be adjusted when the stereo mode
is selected as the beam mode (see page 42).
• FRONT L/R cannot be adjusted when the stereo plus 3 mode is
selected as the beam mode (see page 41).
• Only CENTER can be adjusted when the target mode is
selected as the beam mode (see page 43).
y
If the level of a particular speaker cannot be adjusted, – –dB
appears in the front panel display.
■ Using the test tone
VOL
PRESET: CANCEL
• Select PRESET: RESET to reset all of the current
settings.
• Select PRESET: CANCEL to cancel the resetting
procedure.
You can use the test tone feature to output a test tone from
each speaker to manually balance the speaker levels.
Use the test tone to set speaker levels so that the volume
level of each speaker is identical when heard from your
listening position.
SPORTS
OFF
0
+10
CH LEVEL
5
Press STANDBY/ON on the front panel or on
the remote control to set this unit to the
standby mode.
CINEMA DSP
SURROUND
MENU
ENTER
RETURN
TEST
or
STANDBY/ON
Front panel
Remote control
The new setting will be activated when you turn on
the power of this unit next time.
1
Press TEST on the remote control.
TEST LEFT appears in the front panel display and a
test tone is output from the front left speaker.
TEST
VOL
TEST LEFT
78
ADJUSTING SYSTEM PARAMETERS
2
Press
/
to select the speaker you want
to adjust.
The front panel display changes as follows.
■ Using the audio output being played
back
You can also manually adjust the speaker levels while
playing back an input source such as a DVD.
TEST LEFT
SPORTS
OFF
0
+10
CH LEVEL
SURROUND
CINEMA DSP
MENU
TEST CENTER
ENTER
TEST RIGHT
ENTER
RETURN
TEST
TEST SUR.R
TEST SUR.L
TEST SUBWOOFER
1
Press CH LEVEL repeatedly (or press CH
LEVEL and then
/
) to select the
speaker you want to adjust.
The front panel display changes as follows.
Note
CH LEVEL
TEST SUBWOOFER is only available when a subwoofer is
connected to this unit and SWFR is selected for BASS OUT in
SOUND MENU (see page 70).
or
3
Press
/
to adjust speaker volumes.
CH LEVEL
ENTER
ENTER
FRONT L +1.0dB
Press VOLUME +/– on the remote control to
adjust the volume level of this unit.
CENTER
-2.5dB
FRONT R +1.0dB
VOLUME
SUR.R
+2.0dB
SUR.L
+2.0dB
SWFR
5
ADVANCED
OPERATION
4
Control range: –10 dB to +10 dB
--dB
Press TEST when you have completed all
your adjustments.
TEST
English
y
To adjust the output level of your subwoofer, set BASS OUT to
BOTH or SWFR (page 70).
79
ADJUSTING SYSTEM PARAMETERS
2
Press
/
to adjust speaker volumes.
ENTER
Control range: –10 dB to +10 dB
3
Press CH LEVEL (or wait for a few seconds
without operating this unit) when you have
completed your adjustment.
CH LEVEL
80
SELECTING THE INPUT MODE
SELECTING THE INPUT MODE
You can select the type of audio input signals of the selected input source according to your preference or the conditions
of the input source.
y
We recommend setting the input mode to AUTO in most cases.
STANDBY/ON
POWER
POWER
AV
TV
VCR
STB
TV
INPUT1
TV
INPUT2
MACRO
INPUTMODE
SLEEP
DVD
• AUTO
Automatically selects audio input signals in the following
priority order:
1) Dolby Digital or DTS
2) PCM
3) Analog
Use this input mode in most cases.
AUX
(
)
YSP
1
Press one of the input selector buttons on
the remote control to select the desired input
source.
DVD
VCR
STB
TV
• DTS
Selects only digital signals encoded in DTS.
Compared to AUTO, this input mode provides greater
stability during playback.
Use this input mode when playing back CDs or LDs
encoded in DTS.
• ANALOG
Selects only analog signals.
Even when both digital and analog signals are input
simultaneously, only analog signals are selected.
AUX
Notes
2
Press INPUTMODE on the remote control
repeatedly to toggle between input modes.
• When the input mode is set to AUTO, this unit automatically
plays back multi-channel sources n the selected input mode.
• ANALOG cannot be selected as an input mode if analog signals
are not being input from the selected input source.
y
You can adjust the default input mode to be selected when the
power of this unit is turned on (see page 72).
INPUTMODE
DVD AUTO
AUX AUTO
TV DTS
DVD DTS
AUX DTS
ADVANCED
OPERATION
TV AUTO
TV ANALOG
When TV or STB
is selected as
the input source
When DVD is
selected as the
input source
When AUX is
selected as the
input source
Notes
English
• The input mode of VCR is fixed to ANALOG. However, if the
TV OPTICAL IN jack of this unit is assigned to VCR, AUTO,
DTS and ANALOG become available as the input mode of
VCR (see page 71).
• ANALOG is not available as the input mode of DVD and AUX.
81
REMOTE CONTROL FEATURES
REMOTE CONTROL FEATURES
In addition to controlling this unit, the remote control can also operate other A/V components made by YAMAHA and
other manufacturers. To control other components, you must set up the remote control with the appropriate remote
control codes.
Note
Depending on the external A/V component you are using, you may not be able to operate the component with the remote control, even
if a remote control code is set. In this case, operate the component using the supplied remote control.
Setting remote control codes
1
You can control other components by setting the
appropriate remote control codes. Codes can be set up for
each input area (TV, STB, DVD, VCR and AUX).
For a complete list of available remote control codes, refer
to “LIST OF REMOTE CONTROL CODES” at the end of
this manual.
VCR
STB
TV
INPUT1
TV
INPUT2
MACRO
INPUTMODE
SLEEP
DVD
While holding down CODE SET, press the
input selector button for the component you
want to set up and then without releasing
CODE SET, enter the remote control code
using the numeric buttons.
The following illustrations show an example of
setting the remote control code for a DVD player
made by YAMAHA.
Setting example: YAMAHA DVD input area
AUX
(
)
6
TV MUTE
YSP
5BEAM
ST+3BEAM
3BEAM
1
2
3
STEREO
TARGET
4
5
6
MUSIC
MOVIE
VOL MODE
7
8
9
OFF
SURROUND
0
+10
CINEMA DSP
9
CODE SET
9
2
MENU
ENTER
RETURN
TEST
VOL MODE
DVD
VOL MODE
SPORTS
CH LEVEL
While holding
down, press
VOLUME
CH
TV VOL
MUTE
TV INPUT
TV MUTE
CODE SET
Refer to “Controlling other components” on
page 83 to operate the external component
using the remote control.
If the external component functions correctly, the
remote control code setup was successful.
If the external component does not function correctly,
the remote control code may be incorrect. Confirm
that the remote control code is correct (see “LIST OF
REMOTE CONTROL CODES” at the end of this
manual) and start over from step 1.
Note
If the manufacturer of your component has more than one code,
try each of them until you find the correct one.
If the remote control is without batteries for more than
2 minutes, or if exhausted batteries remain in the
remote control, the contents of the memory may be
cleared. When the memory is cleared, insert new
batteries and reset the remote control codes.
When changing the batteries, be careful not to press
any of the buttons on the remote control. Doing so will
clear the contents of the memory.
82
REMOTE CONTROL FEATURES
Controlling other components
■ Operating your TV
■ Operating your DVD player
Press TV to select TV as the input source.
Press DVD to select DVD as the input source.
DVD
TV
POWER
POWER
AV
TV
VCR
STB
TV
INPUT1
TV
INPUT2
MACRO
STANDBY/ON
DVD
POWER
AV
TV
VCR
STB
TV
INPUT1
TV
INPUT2
MACRO
INPUTMODE
SLEEP
1
DVD
AUX
(
)
INPUTMODE
SLEEP
(
)
YSP
5BEAM
ST+3BEAM
3BEAM
5BEAM
ST+3BEAM
3BEAM
1
2
3
1
2
3
STEREO
TARGET
STEREO
TARGET
4
5
6
MUSIC
MOVIE
VOL MODE
2
4
5
6
MUSIC
MOVIE
VOL MODE
7
8
9
7
8
9
SPORTS
OFF
SURROUND
SPORTS
OFF
SURROUND
0
CH LEVEL
1
AUX
YSP
2
POWER
STANDBY/ON
0
+10
CINEMA DSP
MENU
CH LEVEL
+10
CINEMA DSP
MENU
3
4
ENTER
RETURN
TEST
VOLUME
CH
RETURN
TEST
TV VOL
5
VOLUME
CH
TV VOL
MUTE
TV INPUT
TV MUTE
4
3
MUTE
5
ENTER
TV INPUT
TV MUTE
6
CODE SET
CODE SET
ADVANCED
OPERATION
6
1 TV POWER
Turns on or off the power of your TV.
1 AV POWER
Turns on or off the power of your DVD player.
2 Numeric buttons
Selects a TV channel for playback.
2 Numeric buttons
Use to enter numeric digits.
3 CH +/–
Switches between the available TV channels.
3 Operation buttons for DVD and VCR players
Use to perform DVD player operations, such as play and
stop.
4 TV VOL +/–
Adjusts the audio output level of the TV.
5 TV MUTE
Temporarily mutes audio output from the TV.
5 Cursor buttons
Use to select DVD menu items.
6 RETURN
Use to return to the previous DVD menu screen or exit the
DVD menu.
83
English
6 TV INPUT
Switches the input source for the TV.
4 MENU
Displays the DVD menu.
REMOTE CONTROL FEATURES
■ Operating your VCR player
Press VCR to select VCR as the input source.
VCR
YSP
POWER
POWER
AV
TV
VCR
STB
TV
INPUT1
TV
INPUT2
MACRO
INPUTMODE
SLEEP
STANDBY/ON
DVD
1
AUX
(
)
YSP
2
5BEAM
ST+3BEAM
3BEAM
1
2
3
STEREO
TARGET
4
5
6
MUSIC
MOVIE
VOL MODE
7
8
9
SPORTS
OFF
SURROUND
0
CH LEVEL
+10
CINEMA DSP
MENU
ENTER
RETURN
TEST
VOLUME
CH
TV VOL
MUTE
TV INPUT
TV MUTE
3
CODE SET
4
1 AV POWER
Turns on or off the power of your VCR.
2 Numeric buttons
Use to enter numeric digits.
3 CH +/–
Switches between the available VCR channels.
4 Operation buttons for DVD and VCR players
Use to perform VCR player operations, such as play and
stop.
84
y
Press YSP on the remote control to return to the operation
mode of this unit.
REMOTE CONTROL FEATURES
■ Setting macros for the TV with the
tuning capability
Using the TV macro
The TV macro feature makes it possible to perform a
series of operations with the press of a single button. For
example, when you want to play a DVD, you would
normally turn on the component, select DVD as the input
source and press the play button to start playback. The TV
macro feature lets you perform all of these operations
simply by pressing the DVD macro button.
1
Notes
• The ways to set macros differ if your TV does not have the
tuning capability.
• If you press any control buttons on the remote control other than
the ones used to set macros while setting macros, the setting
procedure is automatically canceled.
• If it takes more than 10 seconds in steps 2 and 3, the setting
procedure is automatically canceled. In this case, repeat from
step 1.
2
Press and hold CODE SET on the remote
control and then press one of the input
selector buttons to select the input source
you want to set macros for.
Proceed to step 2 while holding down CODE SET.
TV MUTE
DVD
CODE SET
AUX
POWER
POWER
AV
TV
VCR
STB
TV
INPUT1
TV
INPUT2
MACRO
INPUTMODE
SLEEP
DVD
3
YSP
ST+3BEAM
3BEAM
1
2
3
STEREO
TARGET
4
5
6
MUSIC
MOVIE
VOL MODE
7
8
9
SPORTS
OFF
SURROUND
0
+10
CH LEVEL
MACRO
CODE SET
AUX
5BEAM
Press CH +/– or the numeric buttons to select
the TV channel.
Check that the TV screen changes to the tuner screen.
CH
or
5BEAM
ST+3BEAM
3BEAM
1
2
3
STEREO
TARGET
4
5
6
MUSIC
MOVIE
VOL MODE
7
8
9
SPORTS
OFF
0
CINEMA DSP
TV
STB
Press MACRO on the remote control while
holding down CODE SET.
TV MUTE
STANDBY/ON
VCR
+10
MENU
CINEMA DSP
RETURN
VOLUME
CH
Press TV INPUT on the remote control
repeatedly so that the screen changes to the
display of the input source selected in step 1.
TV VOL
ADVANCED
OPERATION
4
ENTER
TEST
TV INPUT
MUTE
TV INPUT
TV MUTE
CODE SET
5
Press ENTER on the remote control to
confirm the macro setting.
English
ENTER
85
REMOTE CONTROL FEATURES
■ Setting macros for the TV without the
tuning capability
■ Operating macros
1
1
2
Press and hold CODE SET on the remote
control and then press one of the input
selector buttons to select the input source
you want to set macros for.
Proceed to step 2 while holding down CODE SET.
TV MUTE
DVD
CODE SET
AUX
VCR
STB
DVD
TV
STB
TV
■ Canceling the macros
1
MACRO
CODE SET
Press INPUT1 on the remote control.
Press and hold CODE SET on the remote
control and then press one of the input
selector buttons to select the input source
you want to cancel the macros for.
Proceed to step 2 while holding down CODE SET.
TV MUTE
INPUT1
CODE SET
2
4
VCR
AUX
Press MACRO on the remote control while
holding down CODE SET.
TV MUTE
3
Press and hold one of the input selector
buttons for approximately 2 seconds to
select the input source you want to operate
macros for.
The TV input changes at the same time the input
mode changes.
Press CH +/– or TV INPUT on the remote
control repeatedly so that the screen
changes to the display of the input source
selected in step 1.
DVD
VCR
STB
TV
AUX
Press MACRO on the remote control while
holding down CODE SET.
MACRO
TV MUTE
CODE SET
CH
TV INPUT
or
5
Press ENTER on the remote control to
confirm the setting.
ENTER
86
3
Press ENTER on the remote control to cancel
the macros.
ENTER
TROUBLESHOOTING
TROUBLESHOOTING
Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below
or if the instruction below does not help, set this unit to the standby mode, disconnect the power cord and contact the
nearest authorized YAMAHA dealer or service center.
■ General
Problem
This unit fails to turn on when
STANDBY/ON is pressed, or enters
the standby mode soon after the
power has been turned on.
Cause
Remedy
See
page
Connect the power supply cable firmly to
the AC wall outlet.
21
This unit has been exposed to a strong
external electric shock (such as lightning
and strong static electricity).
Set this unit to the standby mode,
disconnect the power cable, plug it back
in after 30 seconds, then use it normally.
—
The internal temperature becomes too
high and the overheat protection circuitry
has been activated.
Wait about 1 hour for this unit to cool
down and then turn it back on.
—
The sleep timer has turned the unit off.
Turn on the power, and play the source
again.
—
Incorrect input or output cable
connections.
Connect the cables properly. If the
problem persists, the cables may be
defective.
14
No appropriate input source has been
selected.
Select an appropriate input source with
INPUT or the input selector buttons.
37
The volume is turned down.
Turn up the volume.
38
The sound is muted.
Press MUTE or VOLUME +/– on the
remote control to resume audio output
and then adjust the volume level.
39
Signals this unit cannot reproduce (such
as PCM signals with more than 96 kHz
of sampling frequency) are being
received froma source component.
Play a source whose signals can be
reproduced by this unit.
—
Change the system settings of the source
component.
—
The sleep timer has turned the unit off.
Turn on the power, and play the source
again.
—
The sound is muted.
Press MUTE or VOLUME +/– on the
remote control to resume audio output
and then adjust the volume level.
39
No sound from the effect
speakers.
You are playing back the source or
program in the stereo mode.
Press one of the beam mode buttons on
the remote control to select a multichannel playback mode and then try to
play back the source or program once
more.
40
No sound from the center speaker.
The output level of the center speaker is
set to minimum.
Raise the level of the center speaker.
78
No sound from the surround
speakers.
The output level of the surround speakers
is set to minimum.
Raise the output level of the surround
speakers.
78
No sound from the subwoofer.
BASS OUT in SUBWOOFER SET is set
to FRONT when a Dolby Digital or DTS
signal is being played.
Select SWFR or BOTH.
70
This unit suddenly enters the
standby mode.
No sound
The sound suddenly goes off.
ADDITIONAL
INFORMATION
The power supply cable is not firmly
connected to the AC wall outlet.
English
The source does not contain low bass
signals.
87
TROUBLESHOOTING
Problem
See
page
Cause
Remedy
The listening room is not a regular shape.
Install this unit in a square or rectangular
shaped room.
—
There is no wall in the path of the sound
beam.
Try placing a flat object, such as a board,
in the path of the sound beam.
—
Dolby Digital or DTS sources
cannot be played. (Dolby Digital or
DTS indicator does not light up in
the front panel display.)
The connected component is not set to
output Dolby Digital or DTS digital
signals.
Make an appropriate setting following
the operating instructions for your
component.
—
The input mode is set to ANALOG.
Set the input mode to AUTO.
81
There is noise interference when a
subwoofer is not connected to this
unit.
The protection circuitry was in operation
because a source with strong bass
elements was played back.
Turn down the volume level.
38
Select SWFR for BASS OUT.
70
Connect a subwoofer and adjust settings
for SUBWOOFER SET.
70
Surround sound effects are
insubstantial.
Low frequency sounds are
distorted.
CROSS OVER in SUBWOOFER SET is
set incorrectly.
Set CROSS OVER correctly.
70
On-screen display does not
appear.
The OSD video pin cable is not
connected properly.
Connect the cable properly.
15
TV is not selected as the input source.
Select TV as the input source.
37
No picture is displayed for
external components, such as a
DVD player.
The video cable is not connected
properly.
Connect the cable properly.
15
TV is not selected as the input source.
Select TV as the input source.
37
This unit does not operate
properly.
The internal microcomputer has been
frozen by an external electric shock
(such as lightning or excessive static
electricity) or by a power supply with
low voltage.
Disconnect the AC power cable from the
outlet and then plug it in again after
about 30 seconds.
—
There is noise interference from
digital or high-frequency
equipment.
This unit is too close to the digital or
high-frequency equipment.
Move this unit further away from such
equipment.
—
This unit does not output effect
sounds properly.
The original source includes surround
effects.
Disable surround effect settings on this
unit.
—
88
TROUBLESHOOTING
■ Remote control
Problem
The remote control does not work
and/or function properly.
You cannot operate external
components with this unit’s
remote control.
The cursor buttons do not work
during SET MENU operation.
Cause
Remedy
See
page
Wrong distance or angle.
The remote control will function within a
maximum range of 6 m (20 ft) and no
more than 30 degrees off-axis from the
front panel.
22
Direct sunlight or lighting (from an
inverter type of fluorescent lamp, etc.) is
striking the remote control sensor of this
unit.
Reposition this unit.
—
The batteries are weak.
Replace all batteries.
22
The external component you want to
operate is not selected as the input
source.
Press INPUT on the front panel or the
input selector buttons on the remote
control to select the external component
you want to operate.
37
The remote control code was not
correctly set.
Set the remote control code correctly or
try another code for the same
manufacturer using the “LIST OF
REMOTE CONTROL CODES” at the
end of this manual.
82
Even if the remote control code is
correctly set, there are some models that
do not respond to the remote control.
Use the remote control supplied with the
external component.
—
You pressed an input selector button.
Press TEST once.
—
ADDITIONAL
INFORMATION
English
89
GLOSSARY
GLOSSARY
Audio formats
■ Dolby Digital
Dolby Digital is a digital surround sound system that gives
you completely independent multi-channel audio. With 3
front channels (left, center, and right), and 2 surround
stereo channels, Dolby Digital provides 5 full-range audio
channels. With an additional channel especially for bass
effects, called LFE (low frequency effect), the system has
a total of 5.1-channels (LFE is counted as 0.1 channel). By
using 2-channel stereo for the surround speakers, more
accurate moving sound effects and surround sound
environment are possible than with Dolby Surround. The
wide dynamic range (from maximum to minimum
volume) reproduced by the 5 full-range channels and the
precise sound orientation generated using digital sound
processing provide listeners with previously unheard of
excitement and realism.
With this unit, any sound environment from monaural up
to a 5.1-channel configuration can be freely selected for
your enjoyment.
■ Dolby Pro Logic II
Dolby Pro Logic II is an improved technique used to
decode vast numbers of existing Dolby Surround software.
This new technology enables a discrete 5-channel
playback with 2 front left and right channels, 1 center
channel, and 2 surround left and right channels (instead of
only 1 surround channel for conventional Pro Logic
technology). Music and Game modes are also available for
2-channel sources in addition to the Movie mode.
■ Dolby Surround
Dolby Surround uses a 4 channel analog recording system
to reproduce realistic and dynamic sound effects: 2 front
left and right channels (stereo), a center channel for dialog
(monaural), and a surround channel for special sound
effects (monaural). The surround channel reproduces
sound within a narrow frequency range.
Dolby Surround is widely used with nearly all video tapes
and laser discs, and in many TV and cable broadcasts as
well. The Dolby Pro Logic decoder built into this unit
employs a digital signal processing system that
automatically stabilizes the volume on each channel to
enhance moving sound effects and directionality.
90
■ DTS (Digital Theater Systems)
Digital Surround
DTS digital surround was developed to replace the analog
soundtracks of movies with a 6-channel digital sound
track, and is now rapidly gaining popularity in movie
theaters around the world. Digital Theater Systems Inc.
has developed a home theater system so that you can enjoy
the depth of sound and natural spatial representation of
DTS digital surround in your home. This system produces
practically distortion-free 6-channel sound (technically, a
left, right and center channels, 2 surround channels, plus
an LFE 0.1 channel as a subwoofer, for a total of 5.1channels). The unit incorporates a DTS-ES decoder that
enables 6.1- channel reproduction by adding the surround
back channel to existing 5.1-channel format.
■ Neo:6
Neo:6 decodes the conventional 2-channel sources for 6
channel playback by the specific decoder. It enables
playback with the full-range channels with higher
separation just like digital discrete signal playback. Two
modes are available; Music mode for playing music
sources and Cinema mode for movies.
■ PCM (Linear PCM)
Linear PCM is a signal format under which an analog
audio signal is digitized, recorded and transmitted without
using any compression. This is used as a method of
recording CDs and DVD audio. The PCM system uses a
technique for sampling the size of the analog signal per
very small unit of time. Standing for pulse code
modulation, the analog signal is encoded as pulses and
then modulated for recording.
Audio information
■ LFE 0.1 channel
This channel is for the reproduction of low bass signals.
The frequency range for this channel is 20 Hz to 120 Hz.
This channel is counted as 0.1 because it only enforces a
low frequency range compared to the full-range
reproduced by the other 5/6 channels in Dolby Digital or
DTS 5.1/6.1-channel systems.
INDEX
INDEX
A
Audio Pin Cable..................................................... 15 to 18
B
Beam modes.................................................................... 40
C
Coaxial digital output jack................................................ 8
Coaxial digital input jack.................................................. 8
D
Digital Audio Pin Cable.................................................. 16
Display ........................................................................ 7, 24
Dolby Digital .................................................................. 44
Dolby Pro Logic.............................................................. 44
Dolby Pro Logic II.......................................................... 44
DTS................................................................................. 44
Dynamic range................................................................ 71
E
O
On-screen display (OSD) ................................................24
OSD video pin cable .......................................................15
Optical cable .......................................................15, 18, 19
P
PCM ................................................................................81
Power cable .....................................................................21
R
Remote control ............................................................9, 22
Remote control code .......................................................82
S
Surround mode ................................................................44
Sleep timer ......................................................................55
SET MENU.....................................................................24
T
Test tone ..........................................................................78
BASIC SETUP ............................................................... 57
L
LFE 0.1 channel........................................................ 70, 90
M
MANUAL SETUP.......................................................... 63
MEMORY................................................................. 34, 35
N
Night listening modes ..................................................... 52
ADDITIONAL
INFORMATION
English
91
SPECIFICATIONS
SPECIFICATIONS
AMP SECTION
• Maximum Output Power (EIAJ)
.................................................. 2 W (1 kHz, 10% THD, 4 Ω) × 21
20 W (100 Hz, 10% THD, 4 Ω) × 2
SPEAKER SECTION
Small dia. speakers
............................4 cm (1.5”)-cone magnetic shielding type × 21
Woofers
............................10 cm (3.9”)-cone magnetic shielding type × 2
GENERAL
• Power Supply
[U.S.A. and Canada models] ............................. AC 120 V, 60 Hz
[Australia model] ............................................... AC 240 V, 50 Hz
[U.K. and Europe models] ................................. AC 230 V, 50 Hz
[China model] .................................................... AC 220 V, 50 Hz
[Korea model] .................................................... AC 220 V, 60 Hz
[General model] .................................... AC 110–120 V, 50/60 Hz
[Asia model] ..........................................AC 220–240 V, 50/60 Hz
• Power Consumption .................................................................. 30 W
• Frequency response .................................................. 60 Hz – 20 kHz
• Standby Power Consumption ...................................... 0.1 W or less
• Crossover frequency..................................... 400 Hz (Beam channel)
1 kHz (Stereo channel)
• Dimensions (W x H x D) ................................ 800 × 153 × 115 mm
(31-1/2” x 6” x 4-1/2”)
• Input Jacks
AUDIO VCR, TV/STB (Analog) (1 V, 32 kΩ) .... 2 pairs (Analog)
AUDIO TV/STB, AUX (Optical) ................................ 2 (Digital)
AUDIO DVD (Coaxial) ................................................ 1 (Digital)
• Weight ............................................................... 9.0 kg (19 lbs 14oz)
*
• Output Jacks
SUBWOOFER OUT (1.5 V, less than 120 Hz) ...... 1 (Subwoofer)
VIDEO OUT (1 Vp-p, 75 Ω) ............................................1 (OSD)
• System Connector Jack
OPTIMIZER MIC ........................................1 (Microphone input)
SYSTEM CONNECTOR ................................. 1 (System control)
92
Specifications are subject to change without notice.
LIST OF REMOTE CONTROL CODES
LISTE DES CODES DE COMMANDE
LISTE DER FERNBEDIENUNGSCODES
LISTA ÖVER FJÄRRSTYRNINGSKODER
LISTA DEI CODICI DI TELECOMANDO
LISTA DE CÓDIGOS DE MANDO A DISTANCIA
LIJST MET AFSTANDSBEDIENINGSCODES
TV
ADMIRAL
292, 293, 216
AIWA
294, 276, 283, 284
AKAI
295, 296
ALBA
296
AOC
297
BELL &
HOWELL
292
BESTAR
298
BLAUPUNKT 229, 222
BLUE SKY
298
BRANDT
223
BROC SONIC 297
BUSH
296
BYD:SIGN
201, 202
CLATRONIC 298
CRAIG
224
CROSLEX
225
CURTIS MATHIS
297, 226
DAEWOO
297, 298, 224,
227, 228
DAYTRON
239
DUAL
298
DWIN
293, 281
EMERSON
297, 224, 239, 232
FURGUSON 223, 265, 266
FIRST LINE 298
FISHER
295, 233
FRABA
298
FUJITSU
289
FUNAI
277, 278
GE
293, 297, 234,
235, 236
GOODMANS 296, 298, 223
GRUNDIG
229, 238, 249
HITACHI
297, 239, 242,
243, 285
ICE
296
IRRADIO
296
ITT/NOKIA
244, 245
JC PENNY
293, 297, 234, 237
JVC
296, 246, 247, 286
KENDO
298
KTV
297, 239
LG/GOLDSTAR
297, 298, 239, 237
LOEWE
298, 248
LXI
293, 297, 225,
226, 233
MAGNAVOX 297, 225, 239
MARANTZ
298, 210
MATSUI
295
MEDION
203, 204, 205
MEMOREX
297, 216
MITSUBISHI 299, 297, 259, 287
NAD
226, 255
NEC
297, 252, 282
NOKIA
244, 245
NOKIA OCEANIC
245
NORDMENDE 265, 266
ONWA
296
PANASONIC 234, 235, 236,
253, 288, 211
PHILCO
297, 225, 239
PHILIPS
298, 225, 205
PIONEER
226, 235, 254,
255, 268
PORTLAND 297, 256
PROSCAN
293, 221
PROSCAN
231, 241, 251
PROTON
297, 250, 260, 270
QUASAR
234, 235
RADIO SHACK299, 293, 297
RCA
293, 297, 234,
256, 257, 258, 221
RUNCO
220, 230, 271
SABA
223, 269, 265, 266
SAMPO
281, 297, 280
SAMSUNG
297, 239, 248,
262, 275
SANYO
295, 233, 279,
272, 273, 274, 212
SCHNEIDER 296
SCOTT
297
SHARP
292, 239, 232, 213
SIEMENS
229
SIGNATURE 216
SIGNATURE 292
SONY
263, 214
SYLVANIA
297, 225
SYNPHONIC 217, 218, 219
TELEFUNKUN 269, 264, 265, 266
THOMSON
223, 266
TOSHIBA
292, 226, 267, 215
VIDECH
297, 242
WARDS
297, 239, 232, 216
YAMAHA
299, 292, 242,
285, 287, 253
ZENITH
216, 261, 271
DVD PLAYER
AIWA
648, 649
APEX DIGITAL
652, 653, 654
BYD:SIGN
678, 679
DAEWOO
655
DENON
623, 624
FUNAI
625
HARMAN/KARDON
656, 657
HITACHI
626
JVC
627
KENWOOD
628
KLH
658
LG/GOLDSTAR
645, 663, 664
MARANTZ
699, 659
MITSUBISHI 629
ONKYO
632, 633, 634
PANASONIC 623, 635, 668, 672
PHILIPS
PIONEER
699, 647, 659
636, 637, 638,
673, 674, 675
RCA
639
SAMSUNG
642
SHARP
643
SONY
644, 676, 677
SYLVANIA
662
SYMPHONIC 662
THOMSON
646
TOSHIBA
634, 665, 666, 667
YAMAHA
699, 622, 623, 647
ZERITH
663, 664
VCR
ADMIRAL
395
AIWA
396, 397, 398, 329
AKAI
322, 323, 324
AUDIO DYNAMIC
392, 394
BELL & HOWELL
393
BLAUPUNKT 325, 326
BROC SONIC 327
BUSH
322
CANON
325, 328
CGM
396, 332
CITIZEN
396
CRAIG
396, 363
CURTHIS MATHIS
397, 328, 333
DAEWOO
328, 334, 335
DBX
392, 394
DIMENSIA
333
DYNATECH 397
EMERSON
327, 334, 396, 397
FISHER
393, 336
FUNAI
397
GE
328, 333, 387
GO VIDEO
321, 331, 341,
351, 353, 363
GOODMANS 334, 337
GRUNDIG
332, 338
HITACHI
325, 333, 349,
342, 343
INSTANT REPLAY
325, 328
ITT/NOKIA
393
JC PENNY
392, 393, 394,
328, 333, 349,
396, 363
JVC
392, 394, 344,
345, 346, 347
KENDO
396
KENWOOD
392, 394, 396
LG/GOLDSTAR
396, 388
LOEWE
396, 337
LUXOR
395
LXI
393, 396, 397,
336, 349
MAGNAVOX
MARANTZ
MARTA
MATSUI
MEMOREX
MINOLTA
MITSUBISHI
325, 326, 328
392, 394
396
396
328, 336, 396, 397
333, 349
399, 344, 348,
359, 352, 353
MTC
363, 397
MULTITECH 397, 348, 354
NEC
392, 394, 344, 383
NOKIA
393, 395
NOKIA OCEANIC
395
OKANO
323
OLYMPIC
325, 328
ORION
327
PANASONIC 325, 328, 339,
355, 378, 384,
385, 386
PENTAX
333, 349
PHILCO
325, 328, 397
PHILLIPS
325, 326, 328,
337, 356, 357
PHONOLA
337
PILOT
396
PIONEER
325
QUASAR
325, 328
RCA/PROSCAN
325, 326, 328,
333, 335, 349,
358, 369, 363, 397
REALISTIC
393, 397, 328,
336, 359, 362,
396, 363
SAMSUNG
354, 358, 363,
364, 365, 366
SANSUI
394
SANYO
393, 336, 367
SCHNEIDER 337
SCOTT
399, 335, 336,
348, 359, 352,
354, 358
SELECO
322
SHARP
395, 362, 382
SIEMENS
393
SIGNATURE 2000
395, 397
SONY
368, 379, 372,
373, 374, 375
SYLVANIA
397, 325, 326, 328
SYMPHONIC 397
TANDBERG 334
TANDY
397
TASHIRO
396
TATUNG
392, 394
TEAC
392, 394, 397
TECHNICS
325, 328
TEKNIKA
396
TELEFUNKUN
376, 377
THOMAS
397
i
THORN
TOSHIBA
TOTEVISION
UNITECH
UNIVERSUM
VIDEOSONIC
W.WHOUSE
WARDS
YAMAHA
ZERITH
393, 396
335, 369, 389
363, 396
363
396, 327, 376
363
396
395, 396, 336,
362, 397, 363
399, 392, 393, 394
344, 361, 368,
371, 379, 396, 397
CABLE TV TUNER
ABC
739, 752, 753,
755, 758, 759, 762
GENERAL INSTRUMENT
722
HAMIN
723, 724, 725,
726, 727
HITACHI
722
JEROLD
722, 728, 729,
732, 733, 734,
735, 736, 737
MAGNAVOX 738
MOTOROLA 748
OAK
739, 742, 743
PANASONIC 744, 745, 746,
747, 783, 784
PHILLIPS
763, 764, 765,
766, 767, 768
PIONEER
748, 785
RADIO SHACK749
SCIENTIFIC ATLANTA
752, 753, 754
SONY
756, 757
TOCOM
755
UNIVERSAL 769, 772, 773,
774, 775
VIEWSTAR
764, 766, 776,
777, 778, 779, 782
SATELLITE TUNER
ECHOSTAR
822
GE
837, 838, 839
GENERAL INSTRUMENT
823
HITACHI
824
HUGHES
843, 844, 845, 846
JVC
822
MAGNAVOX 825
PANASONIC 826, 829
PHILLIPS
825, 843, 844,
845, 846, 847,
848, 849
PRIMESTAR 827
PROSCAN
837, 838, 839, 842
RADIO SHACK
828
RCA
837, 838, 839, 842
SAMSUNG
852
SONY
832, 835
TOSHIBA
833, 836
UNIDEN
825
ZENITH
834
ii
YSP-800_UB-cv.fm Page 1 Wednesday, March 12, 2008 4:19 PM
UB
YSP-800
Digital Sound Projector
© 2006
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY. LTD. LEVEL 1, 99 QUEENSBRIDGE STREET, SOUTHBANK, VIC 3006, AUSTRALIA
Black process 45.0° 240.0 LPI
All rights reserved.
OWNER’S MANUAL
Printed in Malaysia
WJ02460-1
YSP-800 Quick Reference Guide.fm Page 1 Wednesday, July 27, 2005 8:59 PM
2. Connecting external components to this unit
Connect this unit to external components such as your TV, DVD player, VCR, digital satellite tuner, cable TV tuner, game console and a subwoofer.
■ Connecting a TV and a DVD player
Connect a TV and a DVD player to this unit. If you connect a subwoofer to this unit, you can enjoy reinforced low bass sounds.
YSP-800 QUICK REFERENCE GUIDE
Note
For further information on connecting other components, see pages 14 to 20 in the supplied Owner’s Manual.
TV
This quick reference guide explains steps to connect a TV and a DVD player to this unit and achieve the surround sound effects in a quick, easy manner.
DVD player
Before installing this unit
This unit creates surround sound by reflecting projected sound beams off the walls of your listening room.
The surround sound effects produced by this unit may not be sufficient when the unit is installed in the following locations.
• Rooms with surfaces inadequate for reflecting sound beams
• Rooms with acoustically absorbent surfaces
• Rooms with measurements outside the following range W (3 to 7 m) x H (2 to 3.5 m) x D (3 to 7 m)
• Rooms with less than 2 m from the listening position to the speaker positions
• Rooms where objects such as furniture are likely to obstruct the path of sound beams
• Rooms where the listening position is close to the walls
• Rooms where the listening position is not in front of this unit
Make sure you leave an adequate amount of ventilation space so that heat can escape. Make at least 5 cm of space above or below this unit.
Side view
5 cm or more
Optical
digital
output
Front
Video
output
Rear
Optical cable (supplied)
Video
input
DVD video pin cable
1. Installing this unit
Install this unit where there are no obstacles such as furniture obstructing the path of sound beams. Otherwise, the desired surround sound effects may not be achieved.
You may install this unit in parallel with the wall or in the corner.
Parallel installation
Install this unit in the exact center of the wall when it
is measured from the left and right corners.
Analog
audio
output
1
L
2
R
Optical
digital
output
OSD video pin cable (supplied)
Corner installation
Install this unit in the corner at a 40º to 50º angle from
the adjacent walls.
Subwoofer pin cable
(in case you connect a subwoofer)
40° to 50°
Audio pin cable (supplied)
Optical cable
(in case of an optical digital connection)
Monaural
input
VCR
TV/STB
AUDIO INPUT
SUBWOOFER VIDEO
DVD
COAXIAL
TV/STB
AUX
OPTICAL
OUT
SYSTEM
CONNECTOR
Subwoofer
DIGITAL INPUT
Rear panel of this unit
An object, such as furniture
An object, such as furniture
This unit
(U.S.A. and Canada models)
Installation example
Install this unit so that the sound beams
can be reflected off the walls.
Wrong
To the AC outlet
Correct
OPTIMIZER MIC
Correct
Optimizer microphone (supplied)
■ Installing the optimizer microphone
The supplied optimizer microphone collects and analyzes the sound that this unit produces in your actual listening environment. Refer to the following two diagrams to install the optimizer
microphone in a proper location once it is connected to this unit. If you use a tripod or the supplied cardboard microphone stand to affix the optimizer microphone, try to place the optimizer
microphone at the same height as your ears would be when you are seated in your listening position.
Using a tripod
Optimizer microphone position
Using the supplied cardboard microphone stand
Optimizer microphone position
Within 1 m
More than 2 m
Within 1 m
Tripod
Printed in Malaysia
WG29100
Within 1 m
More than 2 m
Within 1 m
Cardboard
microphone stand
© 2005
All rights reserved.
YSP-800 Quick Reference Guide.fm Page 2 Wednesday, July 27, 2005 8:59 PM
3. Automatically setting up the listening environment
This unit employs the beam optimization feature and the YAMAHA Parametric Room
Acoustic Optimizer (YPAO) technology with the aid of the supplied optimizer
microphone, allowing you to avoid troublesome listening-based speaker setup and achieve
highly accurate sound adjustments that best match your listening environment.
4. Enjoying surround sound
7
Press
/
/
press ENTER.
/
to select and configure each parameter and then
CH LEVEL
CINEMA DSP
MENU
Notes
• Be advised that it is normal for loud test tones to be output during the AUTO SETUP procedure.
Make sure that there are no children around in the listening room while the AUTO SETUP
procedure is in progress.
• Make sure that your listening room is as quiet as possible while the AUTO SETUP procedure is in
progress.
• Once the AUTO SETUP procedure has started, position yourself beside or behind this unit so that
you may not obstruct the path of sound beams. To achieve the best results possible, however, it is
strongly recommended that you should evacuate yourself from your listening room until the AUTO
SETUP procedure is completed.
• Once the AUTO SETUP procedure has completed, be sure to disconnect the optimizer microphone
and keep it in a safe place for future usage.
• The optimizer microphone is sensitive to heat. Keep it away from direct sunlight and do not place it
on top of this unit or other A/V components.
1
Press STANDBY/ON on the remote control to turn on the power of this
unit.
If a subwoofer with adjustable volume and crossover/high cut frequency controls is
connected to this unit, set the volume between 9 and 12 o’clock as viewed on a
conventional clockface and set the crossover/high cut frequency to the maximum.
STANDBY/ON
DVD
VCR
POWER
POWER
AV
TV
STB
TV
ENTER
3
4
MOUNTING (Mounting)
Use to select the mounted position of the unit in your listening room.
Choices: SHELF (Shelf mount), WALL (Wall mount)
• Select WALL if the unit is mounted on the wall.
• Select SHELF if the unit is mounted on the shelf.
REFLECTING (Reflecting)
Use to select the reflectivity of your listening room.
Choices: NORMAL (Normal), HI ECHO (High echo)
• Select NORMAL if your listening room has a normal reflectivity.
• Select HI ECHO if your listening room has highly reflective surfaces such as concrete
walls.
CINEMA DSP
MENU
Check the following points once again before starting the AUTO SETUP
procedure.
• Is the optimizer microphone firmly connected to this unit?
• Is the optimizer microphone placed in a proper location?
• Are there any large obstacles in between the optimizer microphone and the walls in
your listening room?
9
Press ENTER to start the AUTO SETUP procedure.
The following screen appears on your TV.
ENVIRONMENT CHECK (Environmental noise check), SUB WOOFER CHECK
(Subwoofer check) and WILL START in 10 SEC (Will start in 10 sec) are displayed
in order as the PREPARATION procedure is in progress.
SET MENU
CH LEVEL
CINEMA DSP
MENU
.BEAM+SOUND OPTIMZ
BEAM OPTIMZ only
SOUND OPTIMZ only
ENTER
p
RETURN
CINEMA DSP
TEST
2
Press TV on the remote control to select TV as the input source.
2
Press DVD on the remote control to select DVD as the input source and
then start playback on the DVD player.
STANDBY/ON
POWER
POWER
AV
TV
VCR
STB
TV
INPUT1
INPUT2
MACRO
DVD
RETURN
POWER
POWER
AV
TV
VCR
STB
TV
INPUT1
INPUT2
MACRO
DVD
AUX
3
4
If you hear sound output from your TV speakers, turn down the volume
level using the remote control supplied with your TV until you cannot
hear any sound.
3
If you hear sound output from your TV speakers, turn down the volume
level using the remote control supplied with your TV until you cannot
hear any sound.
4
Press VOLUME +/– on the remote control to adjust the volume level.
Press VOLUME +/– on the remote control to adjust the volume level.
VOLUME
TV VOL
CH
VOLUME
5
Press YSP on the remote control to switch to the operation mode of this
unit.
INPUT1
INPUT2
MACRO
INPUTMODE
SLEEP
5
TV VOL
CH
Press YSP on the remote control to switch to the operation mode of this
unit.
11
Press ENTER to confirm the results.
The following screen is displayed temporarily for a few seconds and then disappear
from your TV.
CH LEVEL
CINEMA DSP
MENU
AUTO SETTING COMPLETED
ENTER
TEST
RETURN
INPUT2
MACRO
INPUTMODE
SLEEP
YSP
6
Press one of the beam mode buttons on the remote control to select the
desired beam mode.
Select one of the five beam modes that best matches the current input source of this
unit.
For further details about the beam modes, see page 40 in the supplied Owner’s
Manual.
5BEAM
ST+3BEAM
3BEAM
1
2
3
STEREO
TARGET
4
5
6
The target mode outputs sound beams in a single channel and is ideal if you do not want the
sound beams to be reflected on the walls in your listening room or if you do not disturb others
asleep while enjoying music or movies at night. In addition, you can adjust the horizontal angle
of the sound beams so that you can hear dialogues clearly even from a distant location such as
the kitchen area in your listening room.
7
BEAM MODE: 5BEAM
SUBWOOFER: NOT APPLICABLE
[ENTER]:Enter
[RETURN]:Cancel
INPUT1
AUX
YSP
Example of the
SHOW RESULT screen
p
p
[]/[]:Up/Down/[p]/[p]:Sel
[ENTER]:Start
STANDBY/ON
AUX
Press VOL MODE on the remote control repeatedly to select the desired
volume mode.
The volume modes are designed to improve listenability at lower volumes and limit
the volume level of the TV so that it will not vary suddenly to a great extent.
For further details about the volume modes, see page 52 in the supplied Owner’s
Manual.
PREPARATION
.INSTALLING;;Parallel to Wall
MOUNTING;;;;SHELF
REFLECTING;;NORMAL
Set MIC in front of YSP
MIN 2m/6.5ft
ENTER
Switch to the video input on your TV using the remote control supplied
with your TV so that the DVD menu screen is displayed.
Check that the following screen is displayed on your TV.
The results of the AUTO SETUP procedure are displayed on your TV.
[]/[]:Up/Down
[ENTER]:Enter
MENU
1
y
10
Press
/
to select BEAM OPT+SOUND OPTIMZ and then press
ENTER.
The following screen appears on your TV.
CH LEVEL
Select the TV channel you want to watch using the remote control
supplied with your TV.
If an error occurs, an error message is displayed. See “Error messages for AUTO SETUP” on
page 33 in the Owner’s Manual for a complete list of error messages and their proper remedies.
Follow the instructions and perform the AUTO SETUP procedure again.
SHOW RESULT
6
1
y
p
RETURN
TEST
;AUTO SETUP
Before performing the steps below, set the volume of this unit to –40 dB. If necessary, adjust the
volume level in step 4 below.
.ENVIRONMENT CHECK
;;;[OK]
SUB WOOFER CHECK
;;;[NOT IN USE]
WILL START in 10 SEC
Move aside or behind YSP
*****-----
p
Press
/
on the remote control to select AUTO SETUP and then
press ENTER.
The following screen appears on your TV.
CH LEVEL
y
Before performing the steps below, set the volume of this unit to –40 dB. If necessary, adjust the
volume level in step 4 below.
PREPARATION
[]/[]:Up/Down
[ENTER]:Enter
TEST
5
MENU
ENTER
p
RETURN
TEST
CINEMA DSP
.;MEMORY
;AUTO SETUP
;BASIC SETUP
;MANUAL SETUP
ENTER
y
AUX
Press MENU on the remote control.
The SET MENU screen appears on your TV.
CH LEVEL
You can enjoy audio signals output from your DVD player in real surround sound.
INSTALLING (Installing)
Use to select the installed position of the unit in your listening room.
Choices: Parallel to Wall (Parallel with wall installation), Angle to Wall or corner
(Corner installation)
• Select Angle to Wall or corner if the unit is installed in the corner.
• Select Parallel to Wall if the unit is installed in parallel with the wall.
Turn on the power of your TV.
Switch to the video input on your TV using the remote control supplied
with the TV.
For example, if you connect the supplied OSD video pin cable to the video input 2
jack of your TV, switch to video input 2 on your TV.
■ Enjoying DVDs in surround sound
You can enjoy audio signals output from your TV in real surround sound.
RETURN
TEST
8
2
■ Enjoying TV in surround sound
MUSIC
MOVIE
7
8
VOL MODE
9
SPORTS
OFF
SURROUND
0
+10
6
Press one of the beam mode buttons on the remote control to select the
desired beam mode.
Select one of the five beam modes that best matches the current input source of this
unit. For further details about the beam modes, see page 40 in the supplied Owner’s
Manual.
5BEAM
ST+3BEAM
3BEAM
1
2
3
STEREO
TARGET
4
5
6