BIXOLON SRP-352plus Product specifications

SRP-350/352plusII
Command Manual
Rev. 1.01
http://www.bixolon.com
SRP-350/352plusII
■ Contents
1. Notice ........................................................................................................................................................................................................ 3
2. Control Commands List in Alphanumeric Order................................................................................................................................... 4
2-1 Command Description Items ................................................................................................................................................................ 6
2-2 Details of Control Commands ............................................................................................................................................................... 7
Rev. 1.01
BIXOLON
-2-
SRP-350/352plusII
1. Notice
This document contains proprietary information of BIXOLON Corporation and its affiliates. You may utilize the information solely for the
purpose of facilitating authorized sales and service of, or developing software and similar products for authorized use with, BIXOLON
products, provided that such proprietary information may not be used, reproduced, or disclosed to any other parties for any other purpose
without the prior written permission of BIXOLON Corporation. BIXOLON has no liability for loss or damage arising from or relating to your
use of or reliance on the information in the document.
We at BIXOLON maintain ongoing efforts to enhance and upgrade the functions and quality of all our products. In following, product
specifications and/or user manual content may be changed without prior notice.
Rev. 1.01
BIXOLON
-3-
SRP-350/352plusII
2. Control Commands List in Alphanumeric Order
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Command
HT
LF
FF
CR
CAN
DLE EOT
DLE DC4
ESC FF
ESC SP
ESC !
ESC $
ESC %
ESC &
ESC *
ESC ESC 2
ESC 3
ESC =
19
Horizontal tab
Print and line feed
Form feed (in page mode)
Print and carriage return
Cancel the print data in page mode
Transmit real-time status
Generate pulse at real-time
Print data in page mode
Set the character right space
Set print mode
Set absolute print position
Select/cancel user-defined character set
Define user-defined character set
Specify bit image mode
Turn underline mode on/off
Select default line spacing
Set line spacing
Select peripheral device
No.
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
Command
ESC M
ESC R
ESC S
ESC T
ESC V
ESC W
ESC \
ESC a
ESC d
ESC i
ESC m
ESC p
ESC t
ESC v
ESC {
FS p
FS q
GS !
ESC ?
Cancel user-defined characters
44
GS $
20
21
ESC @
ESC D
Initialize printer
Set horizontal tab positions
45
46
22
ESC E
Turn emphasized mode on/off
47
23
24
25
ESC G
ESC J
ESC L
Turn double-strike mode on/off
Print and feed paper
Select page mode
48
49
50
GS ( A
GS ( E
GS ( L
GS 8 L
GS ( N
GS ( k
GS *
Rev. 1.01
Function
BIXOLON
Function
Select character font/ MSR card read
Specify an international character set
Select standard mode
Select print direction in page mode
Turn 90° clockwise rotation mode on/off
Set print area in page mode
Set relative print position
Set position alignment
Print and feed n lines
Partial cut
Partial cut
Generate pulse
Select character code table
Transmit paper sensor status
Turn upside-down print mode on/off
Print NV bit image
Define NV bit image
Select character size
Set absolute vertical print position in page
mode
Execute test print
Set NV user memory area
Select graphics data
Select character color
Specify and print the symbol
Define downloaded bit image
-4-
SRP-350/352plusII
No.
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
Command
GS /
GS :
GS B
GS H
GS I
GS L
GS V
GS W
GS ^
GS a
GS f
GS h
GS k
GS r
GS v 0
GS w
BS M
68
BS V
69
BS ^ P
Rev. 1.01
Function
Print downloaded bit image
Start/end macro definition
Turn white/black reverse print mode on/off
Select print position of HRI characters
Transmit printer ID
Set left margin
Select cut mode and executes a partial cut
Set print area width
Execute macro
Enable/Disable Automatic Status Back (ASB)
Select font for HRI characters
Set bar code height
Print bar code
Transmit status
Print raster bit image
Set bar code width
Select device font type
Select cut mode and executes a partial/full
cut
Set power saving mode
BIXOLON
-5-
SRP-350/352plusII
2-1 Command Description Items
Command
Function:
Command function outline
Code:
Command format expressed in ASCII, hexadecimal, and decimal codes
Range:
Argument value (Setting range) for the command
Default:
Initial argument value for the command
Description:
Detailed command function description
Remarks:
Additional information about using the command
Differences:
Variations depending on the printer model
Rev. 1.01
BIXOLON
-6-
SRP-350/352plusII
2-2 Details of Control Commands
HT
Function :
Code :
Horizontal tab
ASCII
Hex
Decimal
HT
09
9
Range:
None
Default:
None
Description :
This command moves the print position to the next horizontal tab position. If the next horizontal tab position is not
specified, this command will be void.
Remarks :
■
Differences:
None
Rev. 1.01
The horizontal tab position is set by <ESC> D.
■ With the underline mode turned on, the underline printing is not applied to the tab space created by this command.
BIXOLON
-7-
SRP-350/352plusII
LF
Function:
Code:
Print and line feed
ASCII
Hex
Decimal
LF
0A
10
Range:
None
Default:
None
Description:
This command prints the data in the print buffer and feeds one line based on the current set line spacing in standard
mode.
Remarks:
■
Differences:
None
Rev. 1.01
In page mode, the printer does not perform actual printing, but moving only the print position to the next line.
BIXOLON
-8-
SRP-350/352plusII
FF
Function :
Code :
Form feed (in page mode)
ASCII
Hex
Decimal
FF
0C
12
Range:
None
Default:
None
Description :
This commands prints all data collected in the printer buffer In page mode. After completion of printing, the printer is
returned to standard mode.if the printer receive next data then the printer buffer is evacuated.
Remarks :
■
■
Differences:
None
Rev. 1.01
The printer is returned to standard mode after completion of printing.
After being printed, all of the existing data in the printer buffer is not evacuated and the print position changes to the
beginning of the line.
■ This command works in page mode enabled by ESC L.
■ This command is only effective in standard mode.
■ If the paper is positioned at the print starting position, this command is ignored, not performing actual paper feeding
operation.
BIXOLON
-9-
SRP-350/352plusII
CR
Function:
Code:
Print and carriage return
ASCII
Hex
Decimal
CR
0D
13
Range:
None
Default:
None
Description:
This command prints the data. With auto line feed enabled, it performs printing and one line feeding same as LF.
Remarks:
■
■
Differences:
None
Rev. 1.01
Auto line feed is only enabled using the memory switch.
Auto line feed is turned on by setting dip switch 1-1.
BIXOLON
- 10 -
SRP-350/352plusII
CAN
Function:
Code:
Cancel the print data in page mode
ASCII
Hex
Decimal
CAN
18
24
Range:
None
Default:
None
Description:
This command clears the receive buffer and print buffers in page mode.
Remarks:
■
Differences:
None
Rev. 1.01
This command is effective only in page mode that is set by ESC L.
BIXOLON
- 11 -
SRP-350/352plusII
DLE EOT
Function:
Code:
Transmit real-time status
ASCII
Hex
Decimal
Range:
1≤n≤4
Default:
None
DLE
10
16
EOT
04
4
n
n
n
Description: This command enables commands to be operable in real-time.
This command transmits the printer-related status specified by n as follows:
n
Function
1
Transmit printer status
2
Transmit off-line status
3
Transmit error status
4
Transmit paper roll sensor status
■
Printer transmits the following status
n=1: Printer status
Bit
0
1
2
3
4
5
Rev. 1.01
Binary
0
1
0
1
0
1
1
0
Hex
00
02
00
04
00
08
10
00
Decimal
0
2
0
4
0
8
16
0
Status
Not used. Fixed to Off
Not used. Fixed to On
Drawer kick-out connector pin 3 is LOW
Drawer kick-out connector pin 3 is HIGH
Online
Offline
Not used. Fixed to On
Not used. Fixed to Off
BIXOLON
- 12 -
SRP-350/352plusII
Bit
6
7
Binary
0
0
Hex
00
00
Decimal
0
0
Status
Not used. Fixed to Off
Not used. Fixed to Off
n=2: Off-line status
Bit
0
1
2
3
4
5
6
7
Off/On
Off
On
Off
On
Off
On
On
Off
On
Off
On
Off
Hex
00
02
00
04
00
08
10
00
20
00
40
00
Decimal
0
2
0
4
0
8
16
0
32
0
64
0
Status
Fixed
Fixed
Cover is closed
Cover is open
Paper is not being fed by using the paper FEED button
Paper is being fed by the paper FEED button
Fixed
No paper-end stop
Printing is being stopped
No error
Error has occurred
Fixed
n=3: Error status
Bit
0
1
2
3
4
5
6
7
Rev. 1.01
Binary
0
1
0
0
1
1
0
0
0
Hex
00
02
00
00
08
10
00
00
00
Decimal
0
2
0
0
8
16
0
0
0
Status
Not used. Fixed to Off
Not used. Fixed to On
Not used. Fixed to Off
No autocutter error
Autocutter error occurred
Not used. Fixed to On
Not used. Fixed to Off
Not used. Fixed to Off
Not used. Fixed to Off
BIXOLON
- 13 -
SRP-350/352plusII
n=4: paper sensor status
Bit
0
1
2,3
4
5,6
7
Remarks:
Binary
0
1
00
11
1
00
11
0
Hex
00
02
00
0C
10
00
60
00
Decimal
0
2
0
12
16
0
96
0
Status
Not used. Fixed to Off
Not used. Fixed to On
Paper near end sensor: paper adequate
Paper near end sensor: paper near end
Not used. Fixed to On
Paper end sensor: paper present
Paper end sensor: paper not present
Not used. Fixed to Off
the status is transmitted to the host upon being requested that can check the printer operational condition with it and
takes appropriate measures accordingly.
■ The real time command is stored into the receive buffer and executed with higher priority than other commands.
■
Differences: None
Rev. 1.01
BIXOLON
- 14 -
SRP-350/352plusII
DLE DC4
Function:
Code:
Generate pulse at real-time
ASCII
Hex
Decimal
DLE
10
16
DC4
14
20
n
n
n
m
m
m
t
t
t
Range:
n = 1, m=0,1, 1 ≤ t ≤ 8
Default:
None
Description:
■
Output the pulse specified by t to connector pin m as following:
m
Connector pin
0
Drawer kick-out connector pin 2
1
Drawer kick-out connector pin 5
■
This command generates the drive pulse to connector pin m with pulse width defined by t as following:
• Drawer kick-out connector pin 2 is selected with m=0 while pin 5 chosen for m=1.
• Pulse ON time is [t x100 ms] and OFF time [t x100 ms].
Remarks:
■
■
Upon receiving this command, the printer outputs the drive pulse to the specified connector pin.
The real time command is stored into the receive buffer and executed with higher priority than other commands.
Differences:
None
Rev. 1.01
BIXOLON
- 15 -
SRP-350/352plusII
ESC FF
Function :
Code :
Print data in page mode
ASCII
Hex
Decimal
ESC
1B
27
FF
0C
12
Range:
None
Default:
None
Description :
This command prints the data in the print buffer collectively in page mode.
Remarks :
■
■
■
■
Differences:
None
Rev. 1.01
This command is effective only in page mode that is selectd by ESC L.
After printing, the data in the print buffer and setting values are not cleared.
The printer can print the data in the print buffer repeatedly using this command.
The printer returns to standard mode by ESC S or ESC @.
BIXOLON
- 16 -
SRP-350/352plusII
ESC SP
Function:
Set the character right space
Code:
ASCII
Hex
Decimal
Range:
0 ≤ n ≤ 255
Default:
n=0
Description:
■
This command sets the size of space to right of character.
• Right space = n × [horizontal motion units].
Remarks:
■
■
In a double width mode, the right space will be doubled.
Horizontal motion unit varies depending the printer model.
Differences:
Horizontal motion unit:
ESC
1B
27
SP
20
32
n
n
n
SRP-350plusII:
0.141mm(1/180 inch)
■ SRP-352plusII:
0.125mm(1/203 inch)
■
Rev. 1.01
BIXOLON
- 17 -
SRP-350/352plusII
ESC !
Function:
Set print mode
Code:
ASCII
Hex
Decimal
Range:
0 ≤ n ≤ 255
Default:
n=0
Description:
This command selects print mode(s) with bits having following meanings.
Bit
Off/On
Hex
Decimal
Function
Off
00
0
Character font A selected
0
On
01
1
Character font B selected
1,2
Off
00
0
Reserved
Off
00
0
Emphasized mode not selected
3
On
08
8
Emphasized mode selected
Off
00
0
Double-height mode not selected
4
On
10
16
Double-height mode selected
Off
00
0
Double-width mode not selected
5
On
20
32
Double-width mode selected
6
Off
00
0
Reserved
Off
00
0
Underline mode not selected
7
On
80
128
Underline mode selected
Remarks:
■
Differences:
None
Rev. 1.01
ESC
1B
27
!
21
33
n
n
n
As alternative to this command, ESC M, ESC E and ESC – can be used for the selection for character font,
emphasized mode and underline mode respectively.
■ The entire character print width is underlined, but the space skipped by HT is not.
■ If both double width and double height are selected, the characters will be quadrupled.
BIXOLON
- 18 -
SRP-350/352plusII
ESC $
Function:
Code:
Set absolute print position
ASCII
Hex
Decimal
ESC
1B
27
$
24
36
nL
nL
nL
nH
nH
nH
Range:
0 ≤ (nL + nH x 256) ≤ 65535 (0 ≤ nH ≤ 255, 0 ≤ nL ≤ 255)
Default:
None
Description:
This command specifies the next print starting position in reference to the left edge of the print area. The printing start
position is calculated using (nL + nH x 256) x (vertical or horizontal motion units).
Remarks:
■
■
■
Differences:
Horizontal motion unit:
■ SRP-350plusII: 0.141mm(1/180 inch)
■ SRP-352plusII: 0.125mm(1/203 inch)
Rev. 1.01
Any setting values that go beyond the printable area is ignored.
In standard mode, the horizontal motion unit is used for the calculation.
In page mode, the horizontal motion unit is applied when printing start poison is defined to the upper right or lower
right of print area using ESC T, otherwise, the vertical motion unit is used.
BIXOLON
- 19 -
SRP-350/352plusII
ESC %
Function:
Select/cancel user-defined character set
Code:
ASCII
Hex
Decimal
Range:
0 ≤ n ≤ 255
Default:
n=0
Description:
■
This command selects/deselects user-defined character set that is downloaded by user. To make it valid, the least
significant bit should be defined like following.
• When n=0, the user-defined character set is deselected.
• When n=1, the user-defined character set is selected.
Remarks:
■
The resident character set is enabled and used right after canceling the user defined character set.
Differences:
None
Rev. 1.01
ESC
1B
27
%
25
37
n
n
n
BIXOLON
- 20 -
SRP-350/352plusII
ESC &
Function:
Code:
Define user-defined character set
ASCII
Hex
Decimal
ESC
1B
27
Range:
y=3
32 ≤ c1 ≤ c2 ≤ 126
0 ≤ x ≤ 12 (Font A)
0 ≤ x ≤ 9 (Font B)
0 ≤ d ≤ 255
k = c2 – c1 + 1
Default:
None
Description:
■
Remarks:
■
■
Rev. 1.01
&
26
38
y c1 c2 [x1 d1 ... d(yⅹx1)]... [xk d1 ... d(yⅹxk)]
y c1 c2 [x1 d1 ... d(yⅹx1)]... [xk d1 ... d(yⅹxk)]
y c1 c2 [x1 d1 ... d(yⅹx1)]... [xk d1 ... d(yⅹxk)]
This command defines user-defined characters for character codes in a designated range from the start character
code, c1 to the end character code, c2.
• y denotes the number of bytes in the vertical direction, x the number of dots in the horizontal direction, and d the
dot data for the user-defined characters.
Alphanumeric characters (20H (decimal 32) to 7EH (decimal 126)) are definable.
Once user defined characters are defined, they remain available until they are redefined; ESC ? or ESC @ is
executed; the printer is reset.
■ The following shows the relationship between the definition data and printing result with downloaded character
consisting of 9x7 dots.
BIXOLON
- 21 -
SRP-350/352plusII
MSB
d1
d3
d5
d7
d9
d11
d13
LSB
MSB
d2
d4
d6
d8
d10
d12
d14
LSB
Differences:
Rev. 1.01
None
BIXOLON
- 22 -
SRP-350/352plusII
ESC *
Function:
Code:
Specify bit image mode
ASCII
Hex
Decimal
ESC
1B
27
*
2A
42
m
m
m
nL
nL
nL
nH
nH
nH
Range:
m = 0, 1, 32, 33
0 ≤ nL ≤ 255
0 ≤ nH ≤ 3
0 ≤ d ≤ 255
k = nL + nH × 256 [in case of m = 0, 1]
k = (nL + nH × 256) × 3 [in case of m = 32, 33]
Default:
None
d1...dk
d1...dk
d1...dk
Description: ■ This command specifies the bit image for the mode m as to the number of dots specified by nL and nH.
• d specifies the bit image data with 1 for printed data and 0 for not printed.
• k denotes the number of horizontal dots.
Remarks:
■
■
If the bit image data being entered is beyond the number of dots to be printed, the surplus will be discarded.
If the value of m is beyond the conditions, the subsequent data after m will be treated as normal data.
Differences: ■ SRP-350plusII:
DPI : Dots per Inch (25.4mm)
Rev. 1.01
m
Mode
0
1
32
33
8-dot single-density
8-dot double-density
24-dot single-density
24-dot double-density
Number of dots in
vertical direction
8
8
24
24
Vertical dot
density (DPI)
60
60
180
180
BIXOLON
Horizontal dot
density (DPI)
90
180
90
180
Number of bytes (k)
nL + nH x 256
nL + nH x 256
(nL + nH x 256) x 3
(nL + nH x 256) x 3
- 23 -
SRP-350/352plusII
■
SRP-352plusII:
DPI : Dots per Inch (25.4mm)
Rev. 1.01
m
Mode
0
1
32
33
8-dot single-density
8-dot double-density
24-dot single-density
24-dot double-density
Number of dots in
vertical direction
8
8
24
24
Vertical dot
density (DPI)
203/3
203/3
203
203
BIXOLON
Horizontal dot
density (DPI)
203/2
203
203/2
203
Number of bytes (k)
nL + nH x 256
nL + nH x 256
(nL + nH x 256) x 3
(nL + nH x 256) x 3
- 24 -
SRP-350/352plusII
ESC –
Function:
Code:
Turn underline mode on/off
ASCII
Hex
Decimal
ESC
1B
27
Range:
0 ≤ n ≤ 2, 48 ≤ n ≤ 50
Default:
n=0
Description:
■
Remarks:
■
Differences:
None
Rev. 1.01
2D
45
n
n
n
This command enables the print data following it to be printer out underlined.
• The underline mode varied depending on the following values of n:
n
Function
0,48
Turns off underline mode
1,49
Turns on underline mode, set at 1-dot thick
2,50
Turns on underline mode, set at 2-dot thick
The spaces generated by horizontal tab are not underlined.
■ Using bit 7 of ESC !, the underline mode can be activated/deactivated as well.
BIXOLON
- 25 -
SRP-350/352plusII
ESC 2
Function:
Code:
Select default line spacing
ASCII
Hex
Decimal
ESC
1B
27
2
32
50
Range:
None
Default:
None
Description:
This command sets the default line spacing The default line spacing is approximately 3.75 mm, which is equivalent to
30 dots.
Remarks:
■
■
Differences:
Default line spacing:
■ SRP-350plusII: 4.23 mm (30 dots)
■ SRP-352plusII: 3.75 mm(30 dots)
Rev. 1.01
The line spacing can be set independently in standard mode and in page mode.
The setting of this command remains effective until ESC !, ESC @, printer reset or power cycling is executed.
BIXOLON
- 26 -
SRP-350/352plusII
ESC 3
Function:
Set line spacing
Code:
ASCII
Hex
Decimal
Range:
0 ≤ n ≤ 255
Default:
Corresponding to the default line spacing defined by ESC 2
Description:
■
Remarks:
■
■
Differences:
Vertical or horizontal motion unit and maximum line spacing settable:
Model
Vertical unit
Horizontal unit
SRP-350plusII
0.0705mm (1/360 inch)
0.141mm (1/180 inch)
SRP-352plusII
0.0625mm (1/406 inches)
0.125mm (1/203 inches)
Rev. 1.01
ESC
1B
27
3
33
51
n
n
n
This command sets the line spacing using a following rule.
• Line spacing = n x (vertical or horizontal motion units)
With standard mode selected, the vertical motion unit is used.
In page mode, the horizontal motion unit is applied when printing start poison is defined to the upper right or lower
right of print area using ESC T, otherwise, the vertical motion unit is used.
■ The line spacing is settable independently for each of standard and page modes.
BIXOLON
Max line spacing
17.98mm
15.937mm
- 27 -
SRP-350/352plusII
ESC =
Function:
Code:
Select peripheral device
ASCII
Hex
Decimal
ESC
1B
27
=
3D
61
n
n
n
Range:
1≤n≤3
Default:
None
Description:
This command selects the device to which the host computer communicates according to n as follows:
n
Function
1
Enables the printer
2
Disables the printer
3
Enables the printer
Remarks:
■
Differences:
None
Rev. 1.01
The printer discards all of the received data commands with the exception of ESC = and real-time commands while
being disabled.
■ The normal operation will be resumed by ESC @, power cycling or printer reset.
■ If LSB is activated when the printer is disabled by this command, the status is transmitted to the host at a preset
interval.
BIXOLON
- 28 -
SRP-350/352plusII
ESC ?
Function:
Cancel user-defined characters
Code:
ASCII
Hex
Decimal
Range:
32 ≤ n ≤ 126
Default:
None
Description:
This command removes user-defined character specified by character code n.
Remarks:
■
■
Differences:
None
Rev. 1.01
ESC
1B
27
?
3F
63
n
n
n
In place of the deleted user-defined character, the cooresponding resident character is printed.
The user-defined characters for each font can be deleted independently.
BIXOLON
- 29 -
SRP-350/352plusII
ESC @
Function:
Code:
Initialize printer
ASCII
Hex
Decimal
ESC
1B
27
@
40
64
Range:
None
Default:
None
Description:
This command cancels conditions previously set and initializes the printer to the conditions having existed at power on.
Remarks:
■
■
■
■
■
■
Differences:
None
Rev. 1.01
The data in the printer buffer is cleared.
The settings of DIP switch are not re-read.
The data in the receive buffer is not discarded.
All of the settings such as print mode and line feed are cleared.
NV graphics and NV user memory are not cleared.
In page mode, this command removes the data in print areas, restores the initial settings and returns to standard
mode.
BIXOLON
- 30 -
SRP-350/352plusII
ESC D
Function:
Code:
Set horizontal tab position
ASCII
Hex
Decimal
ESC
1B
27
D
44
68
n1...nk
n1...nk
n1...nk
NUL
00
0
Range:
1 ≤ n ≤ 255 , 0 ≤ k ≤ 32
Default:
n = 8, 16, 24, 32, 40,....., 232, 240, 248
Description:
■
Remarks:
■
■
■
■
Differences:
None
Rev. 1.01
This command sets the horizontal tab position.
• n defines the number of columns from the beginning of the line to the horizontal tab setting.
• k denotes the number of horizontal tab positions to be set.
• The horizontal tab position is stored as a value of [character width x n] measured form the beginning of the line.
The data [n]k signifying the set position is transmitted in the ascending order and ends with a NUL code.
ESC D NUL cancels all horizontal tab positions.
Tab position is set at the value of [character width x n] from the beginning of the line.
The character width includes the space to the right of the character, and it will be twice the normal character when the
double width characters are selected.
■ If the data [n]k is equal to or smaller than the preceding data [n]k-1, the horizontal tab setting has been completed.
■ Up to 32 horizontal tabs can be set, the data exceeding this limit is processed as normal ones.
■ Even if the character width is changed after setting the horizontal tab positions, the horizontal tab positions remain
unchanged.
BIXOLON
- 31 -
SRP-350/352plusII
ESC E
Function:
Turn emphasized mode on / off
Code:
ASCII
Hex
Decimal
Range:
0 ≤ n ≤ 255
Default:
n=0
Description:
■
This command turns emphasized mode on or off by toggling the least significant bit of n like following.
• When the LSB of n is 0, emphasized mode is turned off.
• When the LSB of n is 1, emphasized mode is turned on.
Remarks:
■
The setting of this command remains effective until ESC !, ESC @, printer reset or power cycling is executed.
Differences:
None
Rev. 1.01
ESC
1B
27
E
45
69
n
n
n
BIXOLON
- 32 -
SRP-350/352plusII
ESC G
Function:
Turn double-strike mode on/off
Code:
ASCII
Hex
Decimal
Range:
0 ≤ n ≤ 255
Default:
n=0
Description:
■
This command turns double-strike mode on or off by toggling the least significant bit of n like following.
• When the LSB of n is 0, emphasized mode is turned off.
• When the LSB of n is 1, emphasized mode is turned on.
Remarks:
■
The setting of this command remains effective until ESC !, ESC @, printer reset or power cycling is executed.
Differences:
None
Rev. 1.01
ESC
1B
27
G
47
71
n
n
n
BIXOLON
- 33 -
SRP-350/352plusII
ESC J
Function:
Print and feed paper
Code:
ASCII
Hex
Decimal
Range:
0 ≤ n ≤ 255
Default:
None
Description:
This command prints the data in the print buffer and feeds the paper [n X vertical motion unit].
Remarks:
■
■
■
Differences:
Vertical motion unit and maximum feed amount:
Model
Vertical unit
SRP-350plusII
0.0705mm (1/360 inch)
SRP-352plusII
0.0625mm (1/406 inches)
Rev. 1.01
ESC
1B
27
J
4A
74
n
n
n
The maximum feed amount available varies depending on the printer model.
With standard mode selected, the vertical motion unit is used.
In page mode, the horizontal motion unit is applied when printing start poison is defined to the upper right or lower
right of print area using ESC T, otherwise, the vertical motion unit is used.
■ When used in page mode, this command moves only the print position, not executing actual printing.
BIXOLON
Max feed amount
17.98mm
15.937mm
- 34 -
SRP-350/352plusII
ESC L
Function:
Code:
Select page mode
ASCII
Hex
Decimal
ESC
1B
27
L
4C
76
Range:
None
Default:
None
Description:
This command switches from standard mode to page mode.
Remarks:
■
■
■
■
■
■
Differences:
Rev. 1.01
For printing in page mode, ESC T defines the print direction and starting position that is within the print area specified
by ESC W.
The conditions by the following commands are defined independently in standard mode and page mode.
• ESC SP, ESC 2, and ESC 3
The following commands are not activated in page mode.
• ESC L, FS q, GS ( A, GS ( E, GS T
The following commands are not effective in page mode. The conditions set by these commands in page mode are
available when the printer returns to standard mode.
• ESC V, ESC a, ESC {, GS L, and GS W
The printer resumes standard mode by the use of ESC S, FF, and ESC@.
In page mode, the command, FF, prompts printing the data in the printer buffer collectively. LF, CR, ESC J, and ESC
d just move the print position, not performing actual printing.
None
BIXOLON
- 35 -
SRP-350/352plusII
ESC M
Function:
Code:
Select character font
ASCII
Hex
Decimal
ESC
1B
27
M
4D
77
n
n
n
Range:
n = 0, 1, 48, 49
Default:
n=0
Description:
This command selects only-byte character fonts using n as following.
n
Function
0, 48
Character font A selected
1, 49
Character font B selected
Remarks:
■
■
Differences:
None
Rev. 1.01
The printer model has it own configuration of Font A and B.
The setting of this command remains effective until ESC !, ESC @, printer reset or power cycling is executed.
BIXOLON
- 36 -
SRP-350/352plusII
ESC R
Function:
Specify international character set
Code:
ASCII
Hex
Decimal
Range:
0 ≤ n ≤ 13
Default:
n=0
Description:
This command specifies international characters according to n values.
n
Character set
n
Character set
0
U.S.A
7
Spain I
1
France
9
Norway
2
Germany
10
Denmark II
3
U.K
11
Spain II
4
Denmark I
12
Latin America
5
Sweden
13
Korea
6
Italy
Remarks:
■
Differences:
None
Rev. 1.01
ESC
1B
27
R
52
82
n
n
n
The setting of this command remains effective until ESC !, ESC @, printer reset or power cycling is executed.
BIXOLON
- 37 -
SRP-350/352plusII
ESC S
Function:
Code:
Select standard mode
ASCII
Hex
Decimal
ESC
1B
27
S
53
83
Range:
None
Default:
None
Description:
This command enables standard mode.
Remarks:
■
■
Differences:
None
Rev. 1.01
The data in the printer buffer is cleared and the setting by ESC W returns to the default.
The conditions by the following commands are defined independently in standard mode and page mode.
• ESC SP, ESC 2, and ESC 3
■ In standard mode, CAN, ESC FF and GS $ are ignored.
BIXOLON
- 38 -
SRP-350/352plusII
ESC T
Function:
Code:
Select print direction in page mode
ASCII
Hex
Decimal
ESC
1B
27
T
54
84
n
n
n
Range:
0 ≤ n ≤ 3, 48 ≤ n ≤ 51
Default:
n=0
Description:
This command selects the print direction and starting position in page mode.
n
Print Direction
Starting Position
0,48
Left right
Upper left
1,49
Bottom to top
Lower left
2,50
Right left
Lower right
3,51
Top bottom
Upper right
Remarks:
■
■
Differences:
None
Rev. 1.01
The print direction set by this command id not effective in standard mode.
If this command is processed in standard mode, the setting by this command is effective when the printer changes to
page mode.
■ Depending on the print starting position set by this command, the horizontal motion unit or vertical motion unit is used
for the following commands.
• When the starting position is the upper left or lower right of the print area; ESC SP, ESC $, ESC \ use the
horizontal motion unit and ESC 3, ESC J, GS $ the vertical motion unit.
• When the starting position is the upper right or lower left of the print area; ; ESC SP, ESC $, ESC \ use the
vertical motion unit and ESC 3, ESC J, GS $ the horizontal motion unit.
■ The setting of this command remains effective until ESC !, ESC @, printer reset or power cycling is executed.
BIXOLON
- 39 -
SRP-350/352plusII
ESC V
Function:
Code:
Turn 90°clockwise rotation mode on/off
ASCII
Hex
Decimal
ESC
1B
27
Range:
0 ≤ n ≤ 2, 48 ≤ n ≤ 50
Default:
n=0
Description:
■
Remarks:
■
Differences:
None
Rev. 1.01
V
56
86
n
n
n
This command turns 90° clockwise rotation mode on/off in standard mode according to the value of n as following
• When the value of n is equal to 0 or 48, 90°clockwise rotation mode is turned off.
• When the value of n is equal to 1, 2, 48, or 50, 90°clockwise rotation mode is turned on.
In underline mode, the underline printing for 90° clockwise rotated characters does not work, and the relationship
between vertical and horizontal directions is reversed.
■ The 90° clockwise rotation mode is not effective in page mode.
■ If set in page mode, the 90° clockwise rotation mode has effect after the printer returns to standard mode.
■ The setting of this command remains effective until ESC !, ESC @, printer reset or power cycling is executed.
BIXOLON
- 40 -
SRP-350/352plusII
ESC W
Function:
Code:
Set print area in page mode
ASCII
Hex
Decimal
ESC
1B
27
W
57
87
xL
xL
xL
xH
xH
xH
yL
yL
yL
yH
yH
yH
Range:
0 ≤ (xL + xH x 256) ≤ 65535 (0 ≤ xL ≤ 255, 0 ≤ xH ≤ 255)
0 ≤ (yL + yH x 256) ≤ 65535 (0 ≤ yL ≤ 255, 0 ≤ yH ≤ 255)
1 ≤ (dxL + dxH x 256) ≤ 65535 (0 ≤ dxL ≤ 255, 0 ≤ dxH ≤ 255)
1 ≤ (dyL + dyH x 256) ≤ 65535 (0 ≤ dyL ≤ 255, 0 ≤ dyH ≤ 255)
Default:
■
Description:
■
Rev. 1.01
dxL
dxL
dxL
dxH
dxH
dxH
dyL
dyL
dyL
dyH
dyH
dyH
SRP-350plusII:
• When a paper width of 80mm{3.15"} is selected:
(xL + xH x 256) = 0 (xL=0, xH=0)
(yL + yH x 256) = 0 (yL=0, yH=0)
(dxL + dxH x 256) = 512 (dxL=0, dxH=2)
(dyL + dyH x 256) = 1662 (dyL=126, dyH=6)
■ SRP-352plusII:
• When a paper width of 80mm{3.15"} is selected:
(xL + xH x 256) = 0 (xL=0, xH=0)
(yL + yH x 256) = 0 (yL=0, yH=0)
(dxL + dxH x 256) = 576 (dxL=64, dxH=2)
(dyL + dyH x 256) = 1662 (dyL=126, dyH=6)
This command set the position and the size of the printing area in page mode as following.
• Horizontal starting position = [(xL + xH x 256) x (horizontal motion units)]
• Vertical starting position = [(yL + yH x 256) x (vertical motion units)]
• Horizontal printing area width = [(dxL + dxH x 256) x (horizontal motion units)]
• Vertical printing area width = [(dyL + dyH x 256) x (vertical motion units)]
BIXOLON
- 41 -
SRP-350/352plusII
Remarks:
■
■
■
■
■
Differences:
Rev. 1.01
The horizontal and vertical starting positions are out of the printable area, this command is canceled and the following
data is processed as normal data.
If (Horizontal starting position + Horizontal printing area width) is beyond the printable area, the Horizontal printing
area width is set to (Horizontal printing area - Horizontal starting position).
If (Vertical starting position + Vertical printing area width) is beyond the printable area, the Vertical printing area width
is set to (Vertical printing area - Vertical starting position).
This command is not effective in standard mode. If this command is processed in standard mode, the setting by this
command is effective when the printer returns to page mode.
The setting of this command remains effective until ESC !, ESC @, printer reset or power cycling is executed.
The maximum printable area(Max horizontal printable area, Max vertical printable area):
Model
Max horizontal printable area Max vertical printable area
SRP-350plusII
72.2mm(512dots)
234.3mm(1662dots)
SRP-352plusII
72mm(576dots)
207.75mm(1662dots)
BIXOLON
- 42 -
SRP-350/352plusII
ESC \
Function:
Code:
Set relative print position
ASCII
Hex
Decimal
ESC
1B
27
\
5C
92
nL
nL
nL
nH
nH
nH
Range:
0 ≤ (nL + nH x 256) ≤ 65535 (0 ≤ nL 255, 0 ≤ nH ≤ 255)
Default:
None
Description:
■
Remarks:
■
■
■
■
Differences:
None
Rev. 1.01
This command sets the print starting position based on the current position to [(nL + nH × 256) × horizontal or vertical
motion unit].
• The print starting position is moved to (nL + nH x 256)in the right direction based on the current position.
The printer ignores any setting that exceeds the print area.
When the print area has been exceeded, this command is ignored.
With standard mode selected, the vertical motion unit is used.
In page mode, the horizontal motion unit is applied when printing start poison is defined to the upper right or lower
right of print area using ESC T, otherwise, the vertical motion unit is used.
■ Even if the underline mode is turned on, the space skipped by this command is not printed underlined.
BIXOLON
- 43 -
SRP-350/352plusII
ESC a
Function:
Code:
Set position alignment
ASCII
Hex
Decimal
ESC
1B
27
a
61
97
n
n
n
Range:
0 ≤ n ≤2, 48 ≤ n ≤50
Default:
n=0
Description:
This command specifies position alignment for all data in one line in standard mode, using n as follows:
n
Alignment
0, 48
Left alignment
1, 49
Center alignment
2, 50
Right alignment
Remarks:
■
Differences:
None
Rev. 1.01
This command is not effective in page mode. If this command is processed in page mode, the setting by this
command becomes effective when the printer returns to standard mode.
■ The setting of this command remains effective until ESC !, ESC @, printer reset or power cycling is executed.
BIXOLON
- 44 -
SRP-350/352plusII
ESC d
Function:
Print and feed n lines
Code:
ASCII
Hex
Decimal
Range:
0 ≤ n ≤ 255
Default:
None
Description:
This command feeds the paper by n lines after printing the data in the print buffer.
Remarks:
■
■
■
Differences:
None
Rev. 1.01
ESC
1B
27
d
64
100
n
n
n
The per-line paper feed amount is based on the value set by the line spacing related commands, ESC 2 and ESC 3.
In page mode, this command moves only the print position, not performing actual print.
If the feed amount set is beyond the maximum feed amount, the feed amount will be set to the maximum feed
amount automatically.
BIXOLON
- 45 -
SRP-350/352plusII
ESC i
Function:
Code:
Partial cut
ASCII
Hex
Decimal
ESC
1B
27
i
69
105
Range:
None
Default:
None
Description:
This command executes a partial cut of the paper with one point left uncut.
Remarks:
■
The same partial cut as this command is executed using ESC m and GS V.
Differences:
■
■
■
This command is effective for the printer equipped with an autocutter.
Autocutter operation should be enabled by setting the autocutter control DIP switch.
If the autocutter control DIP switch of the printer not equipped with autocutter is set, the printer does not operate,
displaying the error signal by LED.
Rev. 1.01
BIXOLON
- 46 -
SRP-350/352plusII
ESC m
Function:
Code:
Partial cut
ASCII
Hex
Decimal
ESC
1B
27
m
6D
109
Range:
None
Default:
None
Description:
This command executes a partial cut of the paper with one point left uncut.
Remarks:
■
The same partial cut as this command is executed using ESC i and GS V.
Differences:
■
■
■
This command is effective for the printer equipped with an autocutter.
Autocutter operation should be enabled by setting the autocutter control DIP switch.
If the autocutter control DIP switch of the printer not equipped with autocutter is set, the printer does not operate,
displaying the error signal by LED.
Rev. 1.01
BIXOLON
- 47 -
SRP-350/352plusII
ESC p
Function:
Code:
Generate pulse
ASCII
Hex
Decimal
ESC
1B
27
p
70
112
m
m
m
t1
t1
t1
t2
t2
t2
Range:
m = 0, 1, 48, 49
0 ≤ t1 ≤ 255, 0 ≤ t2 ≤ 255
Default:
None
Description:
This command outputs the signals specified with t1 and t2 to the connector pins defined by m.
m
Connector pin
0, 48
Drawer kick-out connector pin 2
1, 49
Drawer kick-out connector pin 5
Remarks:
■
Differences:
None
Rev. 1.01
The ON time is [t1 x 2ms], and the OFF time is as [t2 x 2ms].
• If t2 is smaller than t1, OFF time is set to [t1 x 2ms].
BIXOLON
- 48 -
SRP-350/352plusII
ESC t
Function:
Code:
Select character code table
ASCII
Hex
Decimal
ESC
1B
27
t
74
116
n
n
n
Range:
0 ≤ n ≤ 5, 16 ≤ n ≤ 19, 21 ≤ n ≤ 31, 33 ≤ n ≤ 41, n=255
Default:
For model not supporting Thai character: n=0
For model supporting Thai character support : n = 20
Description:
This command specifies code page according to the value of n as follows:
n
Code page
0
Page 0
437 (USA, Standard Europe)
1
Page 1
Katakana
2
Page 2
850 (Multilingual)
3
Page 3
860 (Portuguese)
4
Page 4
863 (Canadian-French)
5
Page 5
865 (Nordic)
16
Page 16 1252 (Latin I)
17
Page 17 866 (Cyrillic #2)
18
Page 18 852 (Latin 2)
19
Page 19 858 (Euro)
21
Page 21 862 (Hebrew DOS code)
22
Page 22 864 (Arabic)
23
Page 23 Thai42
24
Page 24 1253 (Greek)
25
Page 25 1254 (Turkish)
Rev. 1.01
BIXOLON
- 49 -
SRP-350/352plusII
n
26
27
28
29
30
31
33
34
35
36
37
38
39
Page 26
Page 27
Page 28
Page 29
Page 30
Page 31
Page 33
Page 34
Page 35
Page 36
Page 37
Page 38
Page 39
40
Page 40 1256
41
Page 41
42
Page 42 Khmer (Cambodia)
47
Page 47 1250 (Czech)
255
User Code Page (Space)
Remarks :
■
Differences:
None
Rev. 1.01
Code page
1257 (Baltic)
Farsi
1251 (Cyrillic)
737 (Greek)
775 (Baltic)
Thai14
1255 (Hebrew New code)
Thai 11
Thai 18
855 (Cyrillic)
857 (Turkish)
928 (Greek)
Thai 16
(Arabic)
1258 (Vietnam)
The setting of this command remains effective until ESC !, ESC @, printer reset or power cycling is executed.
BIXOLON
- 50 -
SRP-350/352plusII
ESC v
Function :
Code :
Transmit paper sensor status
ASCII
Hex
Decimal
ESC
1B
27
v
76
118
Range:
None
Default:
None
Description :
■
■
This command transmits a byte of data specifying the paper sensor status.
The status of paper near end and paper end sensors is sent to the host as follows:
• When paper near end is detected, 0x03 is transmitted.
• When paper end is detected, 0xC is transmitted.
Remarks :
■
■
■
The paper sensor status can be transmitted using GS r.
The near end senor is optional while paper end sensor required.
If the printer is not equipped with a near end sensor, the paper near end sensor is considered as normal condition.
Differences:
None
Rev. 1.01
BIXOLON
- 51 -
SRP-350/352plusII
ESC {
Function :
Turns upside-down printing mode on/off
Code :
ASCII
Hex
Decimal
Range:
0 ≤ n ≤ 255
Default:
n=0
Description :
This command selects/deselects upside-down printing mode according to the least significant bit as follows.
LSB
Upside-down mode
0
Turned off
1
Turned on
Remarks :
■
ESC
1B
27
{
7B
123
n
n
n
This command is valid only when entered at the beginning of the line.
■ The upside-down print mode has no effect in page mode. If this command is processed in page mode, upside-down
printing mode is enabled when the printer returns to standard mode.
■ 180 rotated characters are printed from right to left in upside-down print mode.
■ The setting of this command remains effective until ESC !, ESC @, printer reset or power cycling is executed.
Example
Normal
Differences:
Rev. 1.01
Upside- down Mode
None
BIXOLON
- 52 -
SRP-350/352plusII
FS p
Function :
Code :
Print NV bit image
ASCII
Hex
Decimal
FS
1C
28
p
70
112
n
n
n
m
m
m
Range:
1 ≤ n ≤ 255
0 ≤ m ≤ 3, 48 ≤ m ≤ 51
Default:
None
Description :
This command prints NV bit image n using the mode specified by m as follows:
m
Mode
0, 48
Normal
1, 49
Double-width
2, 50
Double-height
3, 51
Quadruple
Remarks :
■
■
■
■
■
■
■
Rev. 1.01
GS ( L and GS ( 8 can be used for printing NV bit image.
The NV bit image is defined by FS q.
n is assigned to each NV bit image to be stored in download order by FS q.
This command has no effect with NV bit image not defined in advance.
In page mode, the NV bit image is saved without being printed.
The printer does not print the NV bit image that is beyond one line of print area.
When using unidirectional print mode, there will be no vertical misali gnment between the top and bottom parts of the
printed pattern.
BIXOLON
- 53 -
SRP-350/352plusII
Differences:
■
SRP-350plusII:
Mode
Normal
Double-width
Double-height
Quadruple
■
Vertical Dot Density (DPI)
203
203
203/2
203/2
DPI : Dots per Inch (25.4mm)
Horizontal Dot Density (DPI)
203
203/2
203
203/2
SRP-352plusII:
Mode
Normal
Double-width
Double-height
Quadruple
Rev. 1.01
Vertical Dot Density (DPI)
180
180
90
90
DPI : Dots per Inch (25.4mm)
Horizontal Dot Density (DPI)
180
90
180
90
BIXOLON
- 54 -
SRP-350/352plusII
FS q
Function:
Code:
Define NV bit image
ASCII
Hex
Decimal
FS
1C
28
q
71
113
n
n
n
[xL xH yL d1...dk]1... [xL xH yL d1...dk]n
[xL xH yL d1...dk]1... [xL xH yL d1...dk]n
[xL xH yL d1...dk]1... [xL xH yL d1...dk]n
Range:
1 ≤ n ≤ 255
1 ≤ (xL + xH ×256) ≤ 1023 (0 ≤ xL ≤ 255, 0 ≤ xH ≤ 3)
1 ≤ (yL + yH ×256) ≤ 288 (0 ≤ yL ≤ 255, yH=0,1)
0 ≤ d ≤ 255
k = (xL + xH × 256) × (yL + yH × 256) × 8
Default:
None
Description:
■
This command defines the NV bit image in the NV memory.
• n denotes the number of the NV being defined.
• (xL, xH) and (yL, yH) set the number of dots in the horizontal and vertical directions to [(xL + xH × 256) x 8] and
[(yL + yH × 256) x 8] respectively for the NV bit image.
Remarks:
■
■
■
■
GS ( L and GS ( 8 can be used for defining NV bit image.
When this command is entered, all NV bit images previously defined are removed from the NV memory.
After completion of this command, the printer executes a software reset to restore the settings as when turned on.
The NV bit image is printed by FS p.
Rev. 1.01
BIXOLON
- 55 -
SRP-350/352plusII
Differences:
Rev. 1.01
■
During the execution of this command, paper feed button, LSB and real time functions will not operate.
• Bit image data and print result are as follows:
.
MSB
d1
dY+1
…
.
.
LSB
MSB
d2
dY+2
…
dk-2
LSB
.
.
MSB
.
.
…
dk-1
.
.
LSB
MSB
dY
dY x 2
…
dk
LSB
■
NV memory is devided into 2 areas for mono and 2-color graphics. The capacity of each NV memory area is 256KB.
None
BIXOLON
- 56 -
SRP-350/352plusII
GS !
Function:
Code:
Select character size
ASCII
Hex
Decimal
GS
1D
29
!
21
33
n
n
n
Range:
0 ≤ n ≤ 255
(1 ≤ Vertical enlargement ≤ 8, 1 ≤ Horizontal enlargement ≤ 8)
Default:
n=0
Description:
■
This command selects the character height and width using bits 0 to 3, and bits 4 to 7 respectively as follows:
Bit
Function
Setting
0
1
2
3
4
5
6
7
Rev. 1.01
Specifies the number of times normal font
size in the vertical direction
Refer to Table 2
[Enlarged in vertical direction]
Specifies the number of times normal font
size in the horizontal direction
Refer to Table 1
[Enlarged in horizontal
direction]
BIXOLON
- 57 -
SRP-350/352plusII
•
Table 1 [Enlarged in horizontal direction]
Hex
Decimal
Enlargement
00
0
1 time (standard)
10
16
2 times
20
32
3 times
30
48
4 times
40
64
5 times
50
80
6 times
60
96
7 times
70
112
8 times
•
Table 2 [Enlarged in vertical direction]
Hex
Decimal
Enlargement
00
0
1 time (standard)
01
1
2 times
02
2
3 times
03
3
4 times
04
4
5 times
05
5
6 times
06
6
7 times
07
7
8 times
Remarks:
■
Differences:
None
Rev. 1.01
The character size set by this command is valid for alphanumeric, user-defined characters, multi-byte code
characters such as Chinese, Japanese, and Korean.
■ Double width and double height modes can be set by ESC !.
■ Multi-byte code characters are specified only by this command.
■ The setting of this command remains effective until ESC @, printer reset or power cycling is executed.
BIXOLON
- 58 -
SRP-350/352plusII
GS $
Function:
Code:
Set absolute vertical print position in page mode
ASCII
Hex
Decimal
GS
1D
29
$
24
36
nL
nL
nL
nH
nH
nH
Range:
0 ≤ (nL + nH x 256) ≤ 65535 (0 ≤ nL ≤ 255, 0 ≤ nH ≤ 255)
Default:
None
Description:
This command sets the absolute vertical print starting position to [(nL + nH × 256) × (vertical or horizontal motion unit)].
Remarks:
■
■
Differences:
None
Rev. 1.01
This command is activated only in page mode and ignored in standard mode.
Either vertical or horizontal motion unit is used according to the print direction set by ESC T as follows:
• With the starting position of the upper left or lower right on the print area, the vertical motion unit is used.
• In other cases, the horizontal motion unit is used.
■ The configuration beyond the print area set by ESC W is ignored.
BIXOLON
- 59 -
SRP-350/352plusII
GS ( A
Function:
Code:
Execute test print
ASCII
Hex
Decimal
GS
1D
29
(
28
40
A
41
65
Range:
(pL + pH x 256) = 2 (pL=2, pH=0)
0 ≤ n ≤ 2, 48 ≤ n ≤ 50
1 ≤ m ≤ 2, 49 ≤ m ≤ 50
Default:
None
Description:
■
Remarks:
■
■
Differences:
None
Rev. 1.01
pL
pL
pL
pH
pH
pH
n
n
n
m
m
m
This command prints a specified pattern for testing on a roll paper.
• Roll paper is selected with n specified as follows:
n
Paper type
0, 48
1, 49
Roll paper
2, 50
• Different kinds of test patterns are selected according to m as follows:
m
Test pattern
1, 49
Hexadecimal dump mode
2, 50
Self-test printing(configuration+default codepage)
3, 51
Not operated
The printer cancels a macro definition in progress If this command is processed. The macro becomes invalid.
After completion of this command, a software reset is executed automatically to restore the printer status set during
power cycling.
■ All of the data transmitted from the host to the printer is printed and identified in hexadecimal dump mode.
■ The real time command and LSB operations are not executed during the printing of printer configuration (m=2, 50).
BIXOLON
- 60 -
SRP-350/352plusII
GS ( E
Function:
Code:
Set NV user memory area
ASCII
Hex
Decimal
GS
1D
29
(
28
40
E
45
69
pL
pL
pL
pH
pH
pH
fn
fn
fn
[parameter]
[parameter]
[parameter]
Range:
None
Default:
None
Description:
This command stores the customized values to the NV user memory area and uses them for the printer operation. The
table below explains the functions available in this command. Executes commands related to the user setting mode by
specifying the function code fn.
fn
Format
No.
Function
1
GS ( E pL pH fn d1 d2
1
Start the user setting mode
2
GS ( E pL pH fn d1 d2 d3
2
End the user setting mode (Performs a soft reset)
GS ( E pL pH fn [a1 b18...b11]...
3
3
Set value(s) for the memory switch
[ak bk8...bk1]
4
GS ( E pL pH fn a
4
Transmit the settings of the memory switch to the host
Remarks:
■
■
■
Differences:
None
Rev. 1.01
pL, pH is used to set the number of bytes following pH to (pL + pH x 256).
The change in the items of the NV user memory is available only after entering the user setting mode.
After completing the user setting mode (Function 2), the printer performs software reset to restore the initial settings
in effect at power on. Receive and print buffers are cleared as well.
■ Since frequent write operation by this command may deteriorate the performance of the NV memory, it is
recommended to write to NV memory when the significant change in the setting is required.
■ While processing this command, the printer remains busy. Therefore the data transmission by the host is not
available. The real time commands and LSB operations are not processed.
BIXOLON
- 61 -
SRP-350/352plusII
<Function 1> GS ( E pL pH fn d1 d2 (fn=1)
Code:
ASCII
Hex
Decimal
GS
1D
29
(
28
40
E
45
69
pL
pL
pL
pH
pH
pH
fn
fn
fn
d1
d1
d1
d2
d2
d2
Range:
(pL + pH x 256) = 1
fn=1
d1=73, d2=78
Default:
None
Description:
This command starts the user setting mode, enabling the printer to notify that the mode has changed as follows:
[Mode change feedback]
Hexadecimal
Decimal
Number of Data
Header
37H
55
1 byte
Flag
20H
32
1 byte
NUL
00H
0
1 byte
Remarks:
■
■
Differences:
None
Rev. 1.01
(pL=1, pH=0)
This command is effective only in standard mode, not in page mode.
Upon entering the user mode setting mode by this command, the printer transmits “mode change feedback” to the
host.
■ The user setting mode should be enabled prior to processing <Function 2> through 12. Otherwise, those functions
are ignored.
■ After confirming “mode change feedback”, it is recommended to send the command to reconfigure the NV user
memory.
BIXOLON
- 62 -
SRP-350/352plusII
<Function 2> GS ( E pL pH fn d1 d2 d3 (fn=2)
Code:
ASCII
Hex
Decimal
GS
1D
29
(
28
40
E
45
69
pL
pL
pL
pH
pH
pH
fn
fn
fn
d1
d1
d1
d2
d2
d2
d3
d3
d3
Range:
(pL + pH x 256) = 1 (pL=1, pH=0)
fn=2
d1=79, d2=85, d3=84
Default:
None
Description:
This command terminates the user setting mode and performs a software reset.
Remarks:
■
■
■
Differences:
None
Rev. 1.01
This command activates setting items set in the user setting mode.
All the setting items will be effective only after performing this command.
After executing a software reset, the printer resumes the setting in effect at power on.
BIXOLON
- 63 -
SRP-350/352plusII
<Function 3> GS ( E pL pH fn [a1 b18...b11]...[ak bk8...bk1] (fn=3)
Code:
ASCII
Hex
Decimal
GS
1D
29
(
28
40
E
45
69
pL
pL
pL
fn
fn
fn
[a1 b18...b11]... [ak bk8...bk1]
[a1 b18...b11]... [ak bk8...bk1]
[a1 b18...b11]... [ak bk8...bk1]
Range:
10≤ (pL + pH x 256) ≤ 65535
fn=3
a=1,2,3,4,5,6,11,12
b=48, 49, 50
Default:
All switches are set to Off(b = 48)
Description:
■
This command changes all the Memory Switch(Msw) 1 through 8 to the value specified by b simultaneously as
follows:
• When b=48, 49, the corresponding bit is set to Off and On respectively.
• When b=50, there is no change in the memory switch.
■
The setting items of the memory switch 1 are as follows:
Value
Remark
Msw
Function
2
1
SRP-350plusII
SRP-352plusII
48
48
Print speed 3
250 mm/s
230 mm/s
1-1~2
48
49
Print speed 2
230 mm/s
200 mm/s
49
48
Print speed 1
200 mm/s
180 mm/s
• The printer supports 3 different printing speeds.
Please be sure that the printing quality at higher speed may be worse than at the lower.
Rev. 1.01
BIXOLON
- 64 -
SRP-350/352plusII
■
The setting items of the memory switch 2 are as follows:
Msw
Value
Function
48
Specification for Destination: Single byte country
2-1
49
Specification for Destination: Double byte country
Code page selection using the memory switch 2-3 through 2-8.
Msw2-8 Msw2-7 Msw2-6 Msw2-5 Msw2-4 Msw2-3
48
48
48
48
48
48
48
48
48
48
49
48
48
48
48
49
48
48
48
48
48
49
49
48
48
48
49
48
48
48
48
48
49
48
49
48
48
48
49
49
48
48
48
48
49
49
49
48
48
49
48
48
48
48
48
49
48
48
49
48
48
49
48
49
48
48
48
49
48
49
49
48
48
49
49
48
48
48
48
49
49
48
49
48
48
49
49
49
48
48
48
49
49
49
49
48
■
Msw2-8
49
49
49
49
49
49
49
Rev. 1.01
Msw2-7
48
48
48
48
48
48
48
Msw2-6
48
48
48
48
49
49
49
Msw2-5
48
48
49
49
48
48
49
Msw2-4
48
49
48
49
48
49
48
Msw2-3
48
49
48
49
48
48
48
BIXOLON
Character Table
PC437
Katakana
PC850
PC860
PC863
PC865
WPC1252
PC866
PC852
PC858
PC862
PC864
Thai42
WPC1253
WPC1254
WPC1257
Character Table
Farsi
WPC1251
PC737
PC775
Thai 14
Hebrew old code
WPC1255
- 65 -
SRP-350/352plusII
Msw2-8
49
49
49
49
49
49
49
49
49
48
Msw2-7
48
49
49
49
49
49
49
49
49
48
Msw2-6
49
48
48
48
48
49
49
49
49
49
Msw2-5
49
48
48
49
49
48
48
49
49
48
Msw2-4
49
48
49
48
49
48
49
48
49
48
Msw2-3
48
48
48
48
48
48
48
48
48
49
Character Table
Thai 11
Thai 18
PC855
PC857
PC928
Thai 16
WPC1256
WPC1258
Khmer
WPC1250
The setting items of the memory switch 3 are as follows:
Specify the emulations to be enabled using the memory switch 3-1 through 3-3
Remark
Msw3-3 Msw3-2 Msw3-1
Emulation seletion
48
48
48
Emulation 1 ( default )
48
48
49
Emulation 2
48
49
48
Emulation 3
48
49
49
Emulation 4
49
48
48
Emulation 5
■
■
Rev. 1.01
Single byte font selection using the memory switch 4-3 through 4-4.
Value
Msw
Single byte font selection
4
3
48
48
Font A
4-3~4
48
49
Font B
49
48
Font C
BIXOLON
Remark
12x24
9x17
9x24
- 66 -
SRP-350/352plusII
■
■
The setting items of the memory switch 5 are as follows:
Msw
Value
5-1
48
Reserved
5-2
48
Reserved
48
2 Color printing disable
5-3
49
2 Color printing enable
5-4
48
Auto line feed disable
5-5~6
48
Reserved
48
Left 2inch mode disable
5-7
49
Left 2inch mode enable
48
Center 2inch mode disable
5-8
49
Center 2inch mode enable
The setting items of the memory switch 6 are as follows:
Msw
Value
Function
48
Auto internal buzzer after cutting disable
6-1
49
Auto internal buzzer after cutting enable
48
Auto internal buzzer option 3 times
6-2
49
Auto internal buzzer option 1 times
48
Auto internal buzzer with cash drawer disable
6-3
49
Auto internal buzzer with cash drawer enable
48
Auto external buzzer after cutting disable
6-4
49
Auto external buzzer after cutting enable
6-5~8
48
Reserved
• Printer generate pulse to internal buzzer automatically for cutting command ESC i and GS V.
• Printer generate pulse to internal buzzer automatically with cash drawer pulse by the setting.
Remarks:
None
Differences:
None
Rev. 1.01
Function
BIXOLON
- 67 -
SRP-350/352plusII
<Function 4> GS ( E pL pH fn a (fn=4)
Code:
ASCII
Hex
Decimal
GS
1D
29
(
28
40
E
45
69
pL
02
2
pH
00
0
fn
04
4
a
a
a
Range:
pL + pH x 256) = 2 (pL=2, pH=0)
fn=4
a=1,2,3,4,5,6,11,12
Default:
None
Description:
This command transmits the setting value of the memory switch corresponding to a.
Hexadecimal
Decimal
Amount of Data
Header
37H
55
1 byte
Identifier
21H
33
1 byte
Setting value
30H or 31H
48 or 49
8 bytes
NUL
00H
0
1 byte
■ The setting value is sent from bit 8 to bit 1, consisting of 8 bytes in total.
• Off: Hexadecimal = 30H / Decimal = 48
• On: Hexadecimal = 31H / Decimal = 49
Remarks:
None
Differences:
None
Rev. 1.01
BIXOLON
- 68 -
SRP-350/352plusII
GS ( L, GS 8 L
Function :
Code :
Select graphics data
ASCII
Hex
Decimal
GS
1D
29
(
28
40
L
4C
76
pL
pL
pL
pH
pH
pH
m
m
m
fn
fn
fn
ASCII
Hex
Decimal
GS
1D
29
8
38
56
L
4C
76
p1
p1
p1
p2
p2
p2
p3
p3
p3
p4
p4
p4
[parameter]
[parameter]
[parameter]
m
m
m
fn
fn
fn
[parameter]
[parameter]
[parameter]
Range:
None
Default:
None
Description :
This command processes graphics data according to the function code (fn).
fn
No.
Format
Function
Transmits the NV graphics momory capacity
0, 48
48
GS ( L pL pH m fn
Prints the graphics data in the print buffer
2, 50
50
GS ( L pL pH m fn
Transmits the remaining capacity of the NV grapics
3, 51
51
GS ( L pL pH m fn
memory
64
64
GS ( L pL pH m fn d1 d2
Transmits the defined NV graphics key code list
Deletes all NV graphics data
65
65
GS ( L pL pH m fn d1 d2 d3
Deletes the specified NV graphics data
66
66
GS ( L pL pH m fn kc1 kc2
GS ( L pL pH m fn kc1 kc2 b xL xH
67
67
Defines the graphics data in the non-volatile memory
yL yH [cd1…dk]1…[c d1…dk]b
Prints the specified NV graphics data
69
69
GS ( L pL pH m fn kc1 kc2 x y
GS ( L pL pH m fn a bx by c xL xH yL
Stores the graphics data in the print buffer memory
112
112
yH d1…dk
Rev. 1.01
BIXOLON
- 69 -
SRP-350/352plusII
Remarks :
■
■
■
Differences:
None
Rev. 1.01
This command is adapted to print image data.
pL, pH specifies the number of bytes following pH using (pL + pH x 256).
Since frequent writing operation could cause the damage to the NV memory, it is recommended to write only when
being required.
■ While storing data by this command, the printer is in BUSY state where receiving of data is not available. Therefore, it
is not recommended to send data during this process.
■ The real time commands and LSB operations are not allowed during NV memory operation process.
BIXOLON
- 70 -
SRP-350/352plusII
<Function 48> GS ( L pL pH m fn (fn=0, 48)
Code :
ASCII
Hex
Decimal
GS
1D
29
(
28
40
L
4C
76
pL
pL
pL
pH
pH
pH
m
m
m
fn
fn
fn
Range:
(pL + pH x 256) = 1 (pL=2, pH=0)
m=48
fn=0, 48
Default:
None
Description :
Tramsmits the total capacityu of the NV bit-image momory (number of bytes in the memory area).
Remarks :
Hexadecimal
Decimal
Amount of Data
Header
37H
55
1 byte
Identifier
21H
33
1 byte
Setting value
30H or 31H
48 or 49
8 bytes
NUL
00H
0
1 byte
■ The total capacity data is converted to character codes corresponding to decial data, then transmitted from the MSB.
■ The data length is variable.
■ The total capacitu of the NV user memory is selectable as any one of[0, 64K, 128K, 192K, 256K] bytes with GS ( E.
The default value is 256K.
Differences:
None
Rev. 1.01
BIXOLON
- 71 -
SRP-350/352plusII
<Function 50> GS ( L pL pH m fn (fn=2, 50)
Code :
ASCII
Hex
Decimal
GS
1D
29
(
28
40
L
4C
76
pL
pL
pL
pH
pH
pH
m
m
m
fn
fn
fn
Range:
(pL + pH x 256) = 1 (pL=2, pH=0)
m=48
fn=2, 50
Default:
None
Description :
This command prints the graphics data defined by the process of Function 112.
Remarks :
■
■
■
■
Differences:
None
Rev. 1.01
The graphics data stored in the printer buffer is printed.
This command is available in standard mode, not in page mode.
The graphics data is defined by Function 112.
The required amount of line feed pitch is used for printing graphics data, regardless of the existing setting value of the
pitch.
BIXOLON
- 72 -
SRP-350/352plusII
<Function 51> GS ( L pL pH m fn (fn=3, 51)
Code:
ASCII
Hex
Decimal
GS
1D
29
(
28
40
L
4C
76
pL
pL
pL
pH
pH
pH
m
m
m
fn
fn
fn
Range:
(pL + pH x 256) = 2
m=48
fn=3, 51
Default:
None
Description:
This command transmits the setting value of the memory switch corresponding to a.
Hexadecimal
Decimal
Amount of Data
Header
37H
55
1 byte
Identifier
21H
33
1 byte
Setting value
30H – 39H
48 - 57
1 - 8 bytes
NUL
00H
0
1 byte
■ The setting value is sent from bit 8 to bit 1, consisting of 8 bytes in total.
• Off: Hexadecimal = 30H / Decimal = 48
• On: Hexadecimal = 31H / Decimal = 49
Remarks:
None
Differences:
None
Rev. 1.01
(pL=2, pH=0)
BIXOLON
- 73 -
SRP-350/352plusII
<Function 64> GS ( L pL pH m fn d1 d2 (fn=64)
Code:
ASCII
Hex
Decimal
GS
1D
29
Range:
(pL + pH x 256) = 4
m=48
fn=64
d1=75, d2=67
Default:
None
Description:
■
Rev. 1.01
(
28
40
L
4C
76
pL
pL
pL
pH
pH
pH
m
m
m
fn
fn
fn
d1
d1
d1
d2
d2
d2
(pL=4, pH=0)
Transmits the defined NV graphics key code list.
Hexadecimal
Decimal
Header
37H
55
Flag
72H
114
Status
40H or 41H
64 or 65
Data
30H – 39H
48 - 57
NUL
00H
0
■ When the key code is not present :
Hexadecimal
Decimal
Header
37H
55
Flag
72H
114
Status
40H
64
NUL
00H
0
BIXOLON
Amount of Data
1 byte
1 byte
1 byte
2 - 80 bytes
1 byte
Amount of Data
1 byte
1 byte
1 byte
1 byte
- 74 -
SRP-350/352plusII
Remarks:
If the number of the key code exceed 40, the key code is transmitted dividing up to 40.
- The status if the continuous transmission data block is present is 41H.
- The status if the continuous transmission data block is not present is 40H.
■ After the [Header-NULL] is transmitted, the printer receives a response from the hosg; then it performs the process
defined by the response.(See the tables below.)
- When the status (existence of the next data block) is Hexadecimal = 41H / Decimal = 65)
Response
Process performed
ASCII
Decimal
ACK
6
Transmits the next data
NAK
21
Transmits the previous data again
CAN
24
Ends the process.
■
- When the status (for the last data block) is Hexadecimal = 40H / Decimal = 64)
Response
Process performed
ASCII
Decimal
ACK
6
Ends the process
NAK
21
Transmits the previous data again
CAN
24
Cancels the process.
Differences:
Rev. 1.01
None
BIXOLON
- 75 -
SRP-350/352plusII
<Function 65> GS ( L pL pH m fn d1 d2 d3 (fn=65)
Code :
ASCII
Hex
Decimal
GS
1D
29
(
28
40
L
4C
76
pL
pL
pL
pH
pH
pH
Range:
(pL + pH x 256) = 5 (pL=5, pH=0)
fn=65
d1=67, d2=76, d3=82
Default:
None
Description :
This command removes all defined NV graphics data.
Remarks :
■
Differences:
None
Rev. 1.01
m
m
m
fn
fn
fn
d1
d1
d1
d2
d2
d2
d3
d3
d3
The graphics data is define by Function 67 into the NV graphics memory with the sector dedicated for storing NV
graphics data.
BIXOLON
- 76 -
SRP-350/352plusII
<Function 66> GS ( L pL pH m fn kc1 kc2 (fn=66)
Code :
ASCII
Hex
Decimal
GS
1D
29
(
28
40
L
4C
76
pL
pL
pL
pH
pH
pH
m
m
m
fn
fn
fn
Range:
(pL + pH x 256) = 4 (pL=4, pH=0)
m=48
fn=66
32 ≤ kc1 ≤ 126
32 ≤ kc2 ≤ 126
Default:
None
Description :
Deletes the NV graphics data defined by the codes kc1 and kc2.
Remarks :
■
Differences:
None
Rev. 1.01
kc1
kc1
kc1
kc2
kc2
kc2
The graphics data is define by Function 67.
BIXOLON
- 77 -
SRP-350/352plusII
<Function 67> GS ( L pL pH m fn kc1 kc2 b xL xH yL yH [cd1…dk]1…[c d1…dk]b (fn=67)
Code :
Range:
ASCII
Hex
Decimal
GS
1D
29
(
28
40
L
4C
76
pL
pL
pL
pH
pH
pH
m
m
m
fn
fn
fn
kc1 kc2 b xL xH yL yH [cd1…dk]1…[c d1…dk]b
kc1 kc2 b xL xH yL yH [cd1…dk]1…[c d1…dk]b
kc1 kc2 b xL xH yL yH [cd1…dk]1…[c d1…dk]b
GS ( L parameter
3 ≤ (pL + pL x 256) ≤ 65535 (0≤pL≤255, 0≤ pH≤255)
GS ( 8 parameter
3 ≤ (p1 + p2 x 256) +p3 x 65535+p4 x 16777216) ≤ 4294967295
(0 ≤ p1L ≤ 255, 0 ≤ p2 ≤ 255, 0 ≤ p3 ≤ 255, 0 ≤ p4 ≤ 255)
Common parameter
m=48
fn=67
a=48
32 ≤ kc1 ≤ 126
32 ≤ kc2 ≤ 126
b=1,2
1 ≤ (xL + xH x 256) ≤ 8192
1 ≤ (yL + yH x 256) ≤ 2304
c=49 (When The monochrome paper is selected)
c=50 (When The two-color paper is selected)
0 ≤ d ≤ 255
k = ( int ( ( xL + xH x 256 ) + 7 ) / 8 ) x ( yL + yH x 256 )
Default:
Rev. 1.01
None
BIXOLON
- 78 -
SRP-350/352plusII
Description :
■
Remarks :
■
■
Differences:
None
Rev. 1.01
The following parameters are used to define the raster graphics data.
• b specifies the number of colors for the defined data.
• xL and xH specify the number of dots in horizontal direction to (xL + xH x 256).
• yL and yH specify the number of dots in horizontal direction to (yL + yH x 256) dots.
• c specifies the color of the defined data.
c
Defined data color
49
Color 1
50
Color 2
- STP-103II is can not use two color printing mode.
Color 1 means black, and Color 2 red that is available for 2-color paper.
If new NV graphics data is saved or the existing data is modified, all of the existing data in NV graphics memory are
flushed and updated using this command. The rest of NV graphics data groups having no change should be
redefined along with the new group stored.
■ When NV graphics data groups are saved, each of the groups is allocated with N in the order of download.
BIXOLON
- 79 -
SRP-350/352plusII
<Function 69> GS ( L pL pH m fn kc1 kc2 x y (fn=69)
Code :
ASCII
Hex
Decimal
GS
1D
29
(
28
40
L
4C
76
pL
pL
pL
pH
pH
pH
m
m
m
fn
fn
fn
kc1
kc1
kc1
kc2
kc2
kc2
Range:
(pL + pH x 256) = 6 (pL=6, pH=0)
m=48, fn=69
32 ≤ kc1 ≤ 126
32 ≤ kc2 ≤ 126
x=1, 2
y=1, 2
Default:
None
Description :
■
Prints the NV graphics data defined by the codes kc1 and kc2.
• The graphics data is enlarged by x and y in the horizontal and vertical directions.
Remarks :
■
■
■
This command prints the NV graphics data defined by Function 67.
In page mode, this command is not effective.
NV graphics data beyond the print area for one line is not printed.
Differences:
None
Rev. 1.01
BIXOLON
x
x
x
y
y
y
- 80 -
SRP-350/352plusII
<Function 112> GS ( L pL pH m fn a bx by c xL xH yL yH d1…dk (fn=112)
Code :
Range:
ASCII
Hex
Decimal
GS
1D
29
(
28
40
L
4C
76
pL
pL
pL
pH
pH
pH
m
m
m
fn
fn
fn
a bx by c xL xH yL yH d1…dk
a bx by c xL xH yL yH d1…dk
a bx by c xL xH yL yH d1…dk
GS ( L parameter
11 ≤ (pL + pL x 256) ≤ 65535 (0≤pL≤255, 0≤ pH≤255)
GS 8 L parameter
11 ≤ (p1 + p2 x 256) +p3 x 65535+p4 x 16777216) ≤ 4294967295
(0 ≤ p1L ≤ 255, 0 ≤ p2 ≤ 255, 0 ≤ p3 ≤ 255, 0 ≤ p4 ≤ 255)
Common parameter
m=48
fn=112
a=48
c=49 (When The monochrome paper is selected)
c=50 (When The two-color paper is selected)
- When single-color paper secified :
1 ≤ (xL + xH x 256) ≤ 1662 (When by =1)
1 ≤ (xL + xH x 256) ≤ 831 (When by =2)
- When two-color paper secified :
1 ≤ (xL + xH x 256) ≤ 831 (When by =1)
1 ≤ (xL + xH x 256) ≤ 415 (When by =2)
0 ≤ d ≤ 255
k = ( int ( ( xL + xH x 256 ) + 7 ) / 8 ) x ( yL + yH x 256 )
Default:
Rev. 1.01
None
BIXOLON
- 81 -
SRP-350/352plusII
Description :
■
This command stores the raster graphics data in the print buffer, enlarged by bx and by in the horizontal and vertical
directions.
• xL, xH specifies the raster graphics data in the horizontal directionas (xL + xH x 256) dots.
• yL, yH specifies the raster graphics data in the vertical direction to (yL + yH x 256) dots.
• d denotes the stored data(raster format).
• k denotes the number of the graphics data.
• c specifies the color of the defined data.
c
Defined data color
49
Color 1
50
Color 2
• Color 1 means black, and Color 2 red or blue that is available for 2-color paper.
Remarks :
■
■
■
The graphics data is stored in the printer buffer directly.
NV graphics data beyond the print area for one line is not printed.
Real time command is not effective during processing of this command.
Differences:
None
Rev. 1.01
BIXOLON
- 82 -
SRP-350/352plusII
GS ( N
Function:
Code:
Select character color
ASCII
Hex
Decimal
GS
1D
29
(
28
40
N
4E
78
pL
pL
pL
pH
pH
pH
Range:
(pL + pH x 256) = 2 (pL=2, pH=0)
n=48
m=49 (when the monochrome paper is selected)
m=49,50 (when the two-color paper is selected)
Default:
m = 49
Description:
■
Remarks:
■
Differences:
None
Rev. 1.01
n
n
n
m
m
m
This command selects the color specified by m.
m
Color
49
Color 1
50
Color 2
• Color 1 means black and Color 2 red.
In white/black reverse mode, the characters are regarded as nonprinting dots and the background is printed in the
color specified by this command.
■ In underline mode, the underline is printed in the color defined by this command.
BIXOLON
- 83 -
SRP-350/352plusII
GS ( k
Function:
Specify and print the symbol
Code:
None
Range:
None
Default:
None
Description:
■
This command processes the data concerning two-dimensional code.
• Symbol type is specified by cn.
• Function code is specified by fn.
cn
Type of Symbol
48
PDF417 (2-dimensional code)
49
QR CODE (2-dimensional code)
cn
48
Rev. 1.01
fn
65
66
67
68
69
70
Function 065
Function 066
Function 067
Function 068
Function 069
Function 070
80
Function 080
81
Function 081
82
Function 082
Function
PDF417: Specify the number of columns
PDF417: Specify the number of rows
PDF417: Specify the width of module
PDF417: Specify the module height
PDF417: Specify the error correction level
PDF417: Specify the option
PDF417: Store the received data in the symbol
storage area
PDF417: Print the symbol data in the symbol
storage area
PDF417: Send the size information of the
symbol data in the symbol storage
area
BIXOLON
- 84 -
SRP-350/352plusII
cn
fn
65
67
69
Function 165
Function 167
Function 169
80
Function 180
81
Function 181
82
Function 182
49
Remarks:
PDF417 symbol data (when cn=48)
■
■
■
■
■
■
Rev. 1.01
Function
QR CODE: Select the module
QR CODE: Select the size of module
QR CODE: Select the error correction level
QR CODE: Store the data in the symbol
storage area
QR CODE: Print the data in the symbol storage
area
QR CODE: Transmit the size information of the
symbol data in the symbol storage
area
The symbol data is defined, stored to the symbol storage area by Function 080 and printed by the specification of
Function 081. The symbol data in the area remains reserved until the following processes are executed:
• Performing Function 080
• Performing ESC @
• Performing the printer reset and power-off
The setting values of Functions 065 to 070 are utilized for the processing of Function 080 or 082. The printable area
must be large enough to accommodate different-size symbols. If not, the symbol may not be printed.
The same symbol data is repeatedly printed by executing Function 081 after performing Function 080.
The same symbol data is printed differently by executing Function 081 after setting the feature of the symbol by using
Functions 065 through 070.
By using Function 082, the symbol size printed by Function 081 is Available.
QRCODE Symbol Data (cn = 49)
The symbol data is defined, stored to the symbol storage area by Function 180 and printed by the specification of
Function 181. The symbol data in the area remains reserved until the following processes are executed:
• Performing Function 180
• Performing ESC @
• Performing the printer reset and power-off
BIXOLON
- 85 -
SRP-350/352plusII
The setting values of Functions 165 to 169 are utilized for the processing of Function 180 or 182. The printable area
must be large enough to accommodate different-size symbols. If not, the symbol may not be printed.
■ The same symbol data is repeatedly printed by executing Function 181 after performing Function 180.
■ The same symbol data is printed differently by executing Function 181 after setting the feature of the symbol by using
Functions 165 through 169.
■ By using Function 182, the symbol size printed by Function 181 is available.
■
Differences:
Rev. 1.01
None
BIXOLON
- 86 -
SRP-350/352plusII
<Function 065> GS ( k pL pH cn fn n (fn=65)
Code:
ASCII
Hex
Decimal
GS
1D
29
(
28
40
k
6B
107
Range:
(pL + pH x 256) = 3 (pL=3, pH=0)
cn=48, fn=65
0 ≤ n ≤ 30
Default:
n=0
Description:
■
Remarks:
■
■
■
Differences:
None
Rev. 1.01
pL
03
3
pH
00
0
cn
30
48
fn
41
65
n
n
n
This command specifies the number of columns in the data area of PDF417.
• When n=0, automatic processing is set
• When n is not 0, the number of columns of the data area is set to n code word.
Settings of this command affect the processing of Functions 081 and 082.
With auto processing (n=0) specified, the maximum number of columns in the data area is set to 30 columns.
The following data is excluded from the number of columns:
• Start and stop patterns
• Indicator code word of left and right
■ With auto processing (n=0) specified, the number of columns is calculated using the following information.
• Printing area when processing Functions 081, 082
• Module width (Function 067)
• Option setting (Function 070)
■ The setting of this command remains effective until ESC @, printer reset or power cycling is executed.
BIXOLON
- 87 -
SRP-350/352plusII
<Function 066> GS ( k pL pH cn fn n (fn=66)
Code:
ASCII
Hex
Decimal
GS
1D
29
(
28
40
k
6B
107
Range:
(pL + pH x 256) = 3 (pL=3, pH=0)
cn=48, fn=66
n=0, 3 ≤ n ≤ 90
Default:
n=0
Description:
■
Remarks:
■
■
■
Differences:
None
Rev. 1.01
pL
03
3
pH
00
0
cn
30
48
fn
42
66
n
n
n
This command specifies the number of rows in the data area of PDF417.
• When n=0, automatic processing is set
• When n is not 0, the number of rows is set to n rows.
Settings of this function affect the processing of Functions 081 and 082.
With auto processing (n=0) specified, the maximum number of rows is set to 90.
With auto processing (n=0) specified, the number of rows is calculated by using the following information:
• Printing area when processing Functions 081, 082
• Module height (Function 068)
■ The setting of this command remains effective until ESC @, printer reset or power cycling is executed.
BIXOLON
- 88 -
SRP-350/352plusII
<Function 067> GS ( k pL pH cn fn n (fn=67)
Code:
ASCII
Hex
Decimal
GS
1D
29
(
28
40
k
6B
107
pL
03
3
pH
00
0
cn
30
48
fn
43
67
n
n
n
Range:
(pL + pH x 256) = 3 (pL=3, pH=0)
cn=48
fn=67
1≤n≤4
Default:
n=3
Description:
This command sets the width of the module of PDF417 symbol to n dots.
Remarks:
■
■
■
Settings of this command affect the processing of Functions 081 and 082.
The setting unit for printer models varies.
The setting of this command remains effective until ESC @, printer reset or power cycling is executed.
Differences:
■
Setting unit(1 dot)
• SRP-350plusII: 0.141(1/180 inch)
• SRP-352plusII: 0.125(1/203 inch)
Rev. 1.01
BIXOLON
- 89 -
SRP-350/352plusII
<Function 068> GS ( k pL pH cn fn n (fn=68)
Code:
ASCII
Hex
Decimal
GS
1D
29
(
28
40
k
6B
107
pL
03
3
pH
00
0
cn
30
48
fn
44
68
n
n
n
Range:
(pL + pH x 256) = 3 (pL=3, pH=0)
cn=48
fn=68
2≤n≤8
Default:
n=3
Description:
This command sets the module height of PDF417 to [the module width x n].
Remarks:
■
■
Differences:
None
Rev. 1.01
Settings of this command affect the processing of Functions 081 and 082.
The setting of this command remains effective until ESC @, printer reset or power cycling is executed.
BIXOLON
- 90 -
SRP-350/352plusII
<Function 069> GS ( k pL pH cn fn m n (fn=69)
Code:
ASCII
Hex
Decimal
GS
1D
29
(
28
40
k
6B
107
Range:
(pL + pH x 256) = 4 (pL=4, pH=0)
cn=48
fn=69
m=48
48 ≤ n ≤ 56
Default:
None
Description:
■
Remarks:
■
■
Differences:
None
Rev. 1.01
pL
04
4
pH
00
0
cn
30
48
fn
45
69
m
m
m
n
n
n
This command specifies the error correction level for PDF417.
• The error correction level is set by “level”.
Settings of this function affect the processing of Functions 081 and 082.
Error correction level specified by “level” (m=48) is as follows:
The number of the error correction codeword is unchanged regardless of the number of codeword in the data area.
n
Function
Number of error correction codeword
48
Error correction level 0
2
49
Error correction level 1
4
50
Error correction level 2
8
51
Error correction level 3
16
52
Error correction level 4
32
53
Error correction level 5
64
54
Error correction level 6
128
55
Error correction level 7
256
56
Error correction level 8
512
■ The setting of this command remains effective until ESC @, printer reset or power cycling is executed.
BIXOLON
- 91 -
SRP-350/352plusII
<Function 070> GS ( k pL pH cn fn m (fn=70)
Code:
ASCII
Hex
Decimal
GS
1D
29
(
28
40
k
6B
107
pL
03
3
pH
00
0
Range:
(pL + pH x 256) = 3 (pL=3, pH=0)
cn=48
fn=70
m=0,1
Default:
m=0
Description:
This command selects the option for PDF417.
m
Function
0
Select the standard PDF417
1
Select the simplified PDF417
Remarks:
■
■
■
Differences:
None
Rev. 1.01
cn
30
48
fn
46
70
m
m
m
Settings of this function affect the processing of Functions 081 and 082.
When simplified PDF417 symbol is canceled, standard PDF417 symbol is automatically selected.
The setting of this command remains effective until ESC @, printer reset or power cycling is executed.
BIXOLON
- 92 -
SRP-350/352plusII
<Function 080> GS ( k pL pH cn fn m d1...dk (fn=80)
Code:
ASCII
Hex
Decimal
GS
1D
29
(
28
40
k
6B
107
pL
pL
pL
pH
pH
pH
cn
30
48
fn
50
80
m
30
48
d1...dk
d1...dk
d1...dk
Range:
4 ≤ (pL + pH x 256) ≤ 65535 (0 ≤ pL ≤ 255, 0 ≤ pH ≤ 255)
cn=48
fn=80
m=48
0 ≤ d ≤ 255
k = (pL + pH x 256) – 3
Default:
None
Description:
This command stores the PDF417 symbol data (d1...dk) in the symbol storage area.
Remarks:
■
■
Differences:
None
Rev. 1.01
The data stored in the symbol storage area by this command remains reserved after processing Function 081 or 082.
The following data should not be included in the symbol data d1..dk since this information is automatically added by
the printer:
• Start pattern and stop pattern.
• Indicator codeword of left and right.
• The descriptor of symbol length (the first code word in the data area).
• The error correction codeword calculated by modulus 929.
■ The setting of this command remains effective until the following processing is performed:
• Executing Function 080
• Executing ESC @
• Executing printer reset or power-off
BIXOLON
- 93 -
SRP-350/352plusII
<Function 081> GS ( k pL pH cn fn m (fn=81)
Code:
ASCII
Hex
Decimal
GS
1D
29
(
28
40
k
6B
107
pL
03
3
pH
00
0
cn
30
48
fn
51
81
m
m
m
Range:
(pL + pH x 256) = 3 (pL=3, pH=0)
cn=48
fn=81
m=48
Default:
None
Description:
This command encodes and prints the PDF417 symbol data in the symbol save area.
Remarks:
■
■
■
■
■
Rev. 1.01
In standard mode, this command is available only when printer is at the beginning of a line or the printer buffer is
empty.
A symbol exceeding the printing area in size can not be printed.
Printing operation is not processed under the following conditions:
• There is no data (Function 080 is not processed).
• If [(number of columns x number of rows) < number of code word] when automatic processing is specified for
number of columns and number of rows.
• Number of code word exceeds 928 in the data area.
The following data is added automatically by the encode processing:
• Start pattern and stop pattern.
• Indicator code word of left and right.
• The descriptor of symbol length (the first code word in the data area).
• The error correction code word calculated by modulus 929.
• Pad codeword.
The data area includes the following codewords:
• Data specified by Function 080.
• The descriptor of symbol length (the first code word in the data area).
BIXOLON
- 94 -
SRP-350/352plusII
The error correction code word calculated by modulus 929.
Pad codeword.
When automatic processing (Function 065) is specified, the number of columns is calculated using the following
information:
• Current printing area
• Module width (Function 067)
• Option setting (Function 070)
• Codeword in the data area
• The maximum number of columns is 30.
When auto processing (Function 066) is specified in page mode, the number of rows is calculated using the following
information:
• Current printing area
• Module height (Function 068)
• Codeword in the data area
• The maximum number of rows is 90.
Except for character size and upside-down printing mode, none of print mode such as emphasized, double-strike, etc,
affects the printing of the symbol.
In standard mode, the paper feed amount set by the paper feed setting command does not affect printing of the
symbol. The printing position returns to the left side of the printable area after printing the symbol.
In page mode, the printer stores the symbol data in the print buffer without executing actual printing.
The quiet zone is not included in the printing data. Be sure to include the adequate quiet zone for executing of this
command.
• The quiet zone means the spaces surrounding the symbol such as upper, lower, left, and right spaces.
•
•
■
■
■
■
■
■
Differences:
Rev. 1.01
None
BIXOLON
- 95 -
SRP-350/352plusII
<Function 082> GS ( k pL pH cn fn m (fn=82)
Code:
ASCII
Hex
Decimal
GS
1D
29
(
28
40
k
6B
107
pL
03
3
pH
00
0
cn
30
48
fn
52
82
m
m
m
Range:
(pL + pH x 256) = 3 (pL=3, pH=0)
cn=48
fn=82
m=48
Default:
None
Description:
This command encodes and sends the size information of the PDF417 symbol data in the symbol storage area.
Remarks:
■
Rev. 1.01
In standard mode, this command is available only when printer is at the beginning of a line or the printer buffer is
empty.
■ The size information for each data is as follows:
Send data
Hex
Decimal
Data
Header
37H
55
1 byte
Identifier
2FH
47
1 byte
Horizontal size
30H – 39H
48 – 57
1 – 5 byte
Separator
1FH
31
1 byte
Vertical size
30H – 39H
48 – 57
1 – 5 byte
Separator
1FH
31
1 byte
Fixed value
31H
49
1 byte
Separator
1FH
31
1 byte
Other information
30H or 31H
48 or 49
1 byte
NUL
00H
0
1 byte
• Horizontal size and vertical size denotes the number of dots of the symbol.
BIXOLON
- 96 -
SRP-350/352plusII
The following data indicates whether or not printing of the symbol is possible:
Hex
Decimal
Condition
30H
48
Printing is possible
31H
49
Printing is impossible
■ The quiet zone is not included in the printing data. Be sure to include the adequate quiet zone for executing of this
command.
■
Differences:
Rev. 1.01
None
BIXOLON
- 97 -
SRP-350/352plusII
<Function 165> GS ( k pL pH cn fn n1 n2 (fn=65)
Code:
ASCII
Hex
Decimal
GS
1D
29
(
28
40
k
6B
107
pL
04
4
pH
00
0
Range:
(pL + pH x 256) = 3 (pL=3, pH=0)
cn=49
fn=65
n1 = 49, 50
n2 =0
Default:
n1 = 50, n2 = 0
Description:
This command sets the QR Code model as follows:
n1
Function
49
Model 1
50
Model 2
Remarks:
■
■
Differences:
None
Rev. 1.01
cn
31
49
fn
41
65
n1
n1
n1
n2
n2
n2
The setting of this command affects <Function 181> and <Function 182>.
The setting of this command remains effective until ESC @, printer reset or power cycling is executed.
BIXOLON
- 98 -
SRP-350/352plusII
<Function 167> GS ( k pL pH cn fn n (fn=67)
Code:
ASCII
Hex
Decimal
GS
1D
29
(
28
40
k
6B
107
pL
03
3
pH
00
0
cn
31
49
fn
43
67
Range:
(pL + pH x 256) = 3 (pL=3, pH=0)
cn=49
fn=67
1<=n<8
Default:
n=3
Description:
This command sets the size of the QR Code module to n dots.
Remarks:
■
■
■
Differences:
None
Rev. 1.01
n
n
n
The setting of this command affects the processing of <Function 181> and <Function 182>.
Since the QR CODE module is square, n = module width = module height.
The setting of this command remains effective until ESC @, printer reset or power cycling is executed.
BIXOLON
- 99 -
SRP-350/352plusII
<Function 169> GS ( k pL pH cn fn n (fn=69)
Code:
ASCII
Hex
Decimal
GS
1D
29
(
28
40
k
6B
107
pL
03
3
pH
00
0
cn
31
49
fn
45
69
n
n
n
Range:
(pL + pH x 256) = 3 (pL=3, pH=0)
cn=49
fn=69
48≤n≤51
Default:
n = 48
Description:
This command sets the error correction level for QR Code.
n
Function
Recovery Amount (%)
48
Error Correction Level L
7
49
Error Correction Level M
15
50
Error Correction Level Q
25
51
Error Correction Level H
30
Remarks:
■
■
■
Differences:
None
Rev. 1.01
The setting of this command affects the processing of <Function 181> and <Function 182>.
Reed-Solomon correction is employed to generate a series of error correction codewords.
The setting of this command remains effective until ESC @, printer reset or power cycling is executed.
BIXOLON
- 100 -
SRP-350/352plusII
<Function 180> GS ( k pL pH cn fn m d1...dk (fn=80)
Code:
ASCII
Hex
Decimal
GS
1D
29
(
28
40
k
6B
107
pL
pL
pL
pH
pH
pH
cn
31
49
fn
50
80
m
30
48
Range:
4 ≤ (pL + pH x 256) ≤7092 (0 ≤ pL ≤ 255, 0 ≤ pH ≤ 27)
cn=49
fn=80
m=48
0 ≤ d ≤ 255
k = (pL + pH x 256) – 3
Default:
None
Description:
This command saves symbol data of the QR Code to the symbol storage area.
Remarks:
■
Differences:
None
Rev. 1.01
d1...dk
d1...dk
d1...dk
The symbol data is defined, stored to the symbol storage area by Function 180 and printed by the specification of
Function 181. The data remains reserved after completion of printing.
■ The following shows the data available for encoding of QR code.
Character Type
Usable Characters
Numeric Data
“0” ~ “9”
Alphanumeric Data
“0” ~ “9”, “A” ~ “Z”, SP, $, %, *, +, -, ., /, :
Kanji Data
Shift JIS value
8bit Byte Data
00H ~ FFH
■ The setting of this command remains effective until the following processing is performed:
• Performing Function 180
• Performing ESC @
• Performing the printer reset or power-off
BIXOLON
- 101 -
SRP-350/352plusII
<Function 181> GS ( k pL pH cn fn m (fn=81)
Code:
ASCII
Hex
Decimal
GS
1D
29
(
28
40
k
6B
107
pL
03
3
pH
00
0
cn
31
49
fn
51
81
m
m
m
Range:
(pL + pH x 256) = 3 (pL=3, pH=0)
cn=49
fn=81
m=48
Default:
None
Description:
This command encodes and prints QR Code symbol data saved in the symbol storage area.
Remarks:
■
Rev. 1.01
In standard mode, this command is available only when printer is at the beginning of a line or the printer buffer is
empty.
■ A symbol exceeding the printing area in size can not be printed.
■ Printing operation is not processed under the following conditions:
• There is no data. (Function 180 is not executed)
• If [(number of columns x number of rows) < number of code words], the numbers of columns and rows are
automatically processed.
• The four types of data compression modes are listed below. According to the symbol data in the data storage area,
automatically selects the best suitable compression mode.
*Numeric Data Code
*Alphanumeric Data mode
*Kanji Data mode
*8 bit Data mode
BIXOLON
- 102 -
SRP-350/352plusII
The following data is automatically added by the encoding processing:
• Position sensor pattern
• Segregator for the position sensor pattern
• Timing pattern
• Format information
• Version information
• Error correction code text
• Pad code text
• Indicator for counting bits of bytes
• Mode indicator
• Concluder
• Queue pattern (when model 2 is selected)
• Expansion pattern (when model 1 is selected)
■ Except for character size and upside-down printing mode, none of print mode such as emphasized, double-strike, etc,
affects the printing of the symbol.
■ In standard mode, the paper feed amount set by the paper feed setting command does not affect printing of the
symbol. The printing position returns to the left side of the printable area after printing the symbol.
■ In page mode, the printer stores the symbol data in the print buffer without executing actual printing.
■ The quiet zone is not included in the printing data. Be sure to include the adequate quiet zone for executing of this
command.
■
Differences:
Rev. 1.01
None
BIXOLON
- 103 -
SRP-350/352plusII
<Function 182> GS ( k pL pH cn fn m (fn=82)
Code:
ASCII
Hex
Decimal
GS
1D
29
(
28
40
k
6B
107
pL
03
3
pH
00
0
cn
31
49
fn
52
82
m
m
m
Range:
(pL + pH x 256) = 3 (pL=3, pH=0)
cn=49
fn=82
m=48
Default:
None
Description:
This command transmits the size information of the QR Code symbol data encoded by Function 180.
Remarks:
■
■
Rev. 1.01
In standard mode, this command is available only when printer is at the beginning of a line or the printer buffer is
empty.
The size information of each data is as follows:
Send data
Hex
Decimal
Data
Header
37H
55
1 byte
Flag
36H
54
1 byte
Horizontal size
30H – 39H
48 – 57
1 – 5 byte
Separator
1FH
31
1 byte
Vertical size
30H – 39H
48 – 57
1 – 5 byte
Separator
1FH
31
1 byte
Fixed Value
31H
49
1 byte
Separator
1FH
31
1 byte
Other Information
30H or 31H
48 or 49
1 byte
NUL
00H
0
1 byte
• Horizontal size and vertical size denotes the number of dots of the symbol.
BIXOLON
- 104 -
SRP-350/352plusII
Differences:
Rev. 1.01
■
The following data indicates whether or not printing of the symbol is possible:
Hex
Decimal
Condition
30H
48
Printing is possible
31H
49
Printing is impossible
■
The quiet zone is not included in size information.
None
BIXOLON
- 105 -
SRP-350/352plusII
GS *
Function:
Code:
Define downloaded bit image
ASCII
Hex
Decimal
GS
1D
29
*
2A
42
x
x
x
y
y
y
[d1...d(x x y x 8)]
[d1...d(x x y x 8)]
[d1...d(x x y x 8)]
Range:
1 ≤ x ≤ 255
1 ≤ y ≤ 48 (where x x y ≤ 1536)
0 ≤ d ≤ 255
Default:
None
Description:
■
This command defines the downloaded bit image using the number of dots specified by x and y.
• x and y specify the number of dots in the horizontal and vertical directions respectively.
• D defines the bit image data.
• K denotes the number of the definition data.
Remarks:
■
■
■
The bit image can be printed by downloaded graphics function, GS ( 8.
The downloaded bit image is available until ESC @, printer reset or power cycling is executed.
The user-defined character and the downloaded bit image cannot be defined simultaneously.
• The user-defined character is cleared preceding the execution of this command.
• The downloaded bit image data is cleared with ESC & executed.
Differences:
None
Rev. 1.01
BIXOLON
- 106 -
SRP-350/352plusII
GS /
Function:
Code:
Print downloaded bit image
ASCII
Hex
Decimal
GS
1D
29
/
2F
47
m
m
m
Range:
0 ≤ m ≤ 3, 48 ≤ m ≤ 51
Default:
None
Description:
This command prints the downloaded bit image defined by GS * according to the mode denoted by m.
DPI : Dots per Inch (25.4mm)
m
Mode
Vertical dot density(DPI)
Horizontal dot density(DPI)
0, 48
Normal
180
180
1, 49
Double-width
180
90
2, 50
Double-height
90
180
3, 51
Quadruple
90
90
Remarks:
■
■
■
Rev. 1.01
The download bit image is defined by GS *.
This command is ignored when if a downloaded bit image is not defined.
In standard mode, this command works only when the print buffer is empty and the printer is in the start of the
line. m is treated as normal data if the print buffer has data.
■ In page mode, the bit image data is accumulated in the print buffer, but does not perform the actual printing.
■ Except for character size and upside-down printing mode, none of print mode such as emphasized, double-strike, etc,
affects the printing of the downloaded bit image.
■ The default dot density set by GS L is applied to printing of the downloaded bit image.
BIXOLON
- 107 -
SRP-350/352plusII
Differences:
■
SRP-350plusII:
m
0, 48
1, 49
2, 50
3, 51
■
Vertical dot density(DPI)
180
180
90
90
Vertical dot density(DPI)
203
203
203/2
203/2
DPI : Dots per Inch (25.4mm)
Horizontal dot density(DPI)
203
203/2
203
203/2
SRP-352plusII:
m
0, 48
1, 49
2, 50
3, 51
Rev. 1.01
Mode
Normal
Double-width
Double-height
Quadruple
DPI : Dots per Inch (25.4mm)
Horizontal dot density(DPI)
180
90
180
90
Mode
Normal
Double-width
Double-height
Quadruple
BIXOLON
- 108 -
SRP-350/352plusII
GS :
Function:
Code:
Start/end macro definition
ASCII
Hex
Decimal
GS
1D
29
:
3A
58
Range:
None
Default:
None
Description:
■
This command starts or ends macro definition.
Remarks:
■
The printer starts macro definition during normal operation and finishes it during macro definition upon receiving this
command.
The printer performs printing during macro definition.
The macro is executed by GS ^.
The maximum number of macro data to be defined varies with respect to printer models. The data exceeding this
limit is not stored.
ESC @ does not clear the existing defined macro. The macro remains effective until the printer reset and power
cycling are executed.
■
■
■
■
Differences:
Rev. 1.01
None
BIXOLON
- 109 -
SRP-350/352plusII
GS B
Function:
Turns white/black reverse printing mode on / off
Code:
ASCII
Hex
Decimal
Range:
0 ≤ n ≤ 255
Default:
n=0
Description:
■
This command selects white/black reverse printing mode by setting the least significant bit of n.
• When the LSB of n is 0, white/black reverse mode is turned off.
• When the LSB of n is 1, white/black reverse mode is turned on.
Remarks:
■
■
■
■
This command does not affect multi-byte characters such as Kanji, Japanese and Korean.
The right space defined by ESC SP is affected by this command.
In white/black reverse mode, the underline mode is not effective.
This mode remains effective until ESC @, printer reset or power cycling is executed.
Differences:
None
Rev. 1.01
GS
1D
29
B
42
66
n
n
n
BIXOLON
- 110 -
SRP-350/352plusII
GS H
Function:
Code:
Selects print position of HRI characters
ASCII
Hex
Decimal
GS
1D
29
H
48
72
n
n
n
Range:
0 ≤ n ≤ 3, 48 ≤ n ≤ 51
Default:
n=0
Description:
■
This command selects the printing position of HRI (Human Readable Interpretation) characters when printing a bar
code.
• The printing position is set according to the value of as follows:
n
Printing position
0, 48
Not printed
1, 49
Above the bar code
2, 50
Below the bar code
3, 51
Both above and below the bar code
Remarks:
■
■
The font of the HRI characters is defined by GS f.
The setting of this command remains effective until ESC @, printer reset or power cycling is executed.
Differences:
None
Rev. 1.01
BIXOLON
- 111 -
SRP-350/352plusII
GS I
Function:
Transmits printer ID
Code:
ASCII
Hex
Decimal
Range:
1 ≤ n ≤ 69
Default:
None
Description:
■
Remarks:
■
Rev. 1.01
GS
1D
29
I
49
73
n
n
n
This command transmits the printer ID or information.
• Transmits 1 byte of printer ID, using n as follows:
n
Printer ID
Specification
1,49
Printer model ID
Printer model
2,50
Type ID
Printer type
3,51
Printer feature ID
Printing method and Printer size
• Transmits specified printer information, using n as follows:
n
Printer ID type
Specification
65
Firmware version
Firmware version
66
Manufacturer
BIXOLON
67
Printer model
Printer model
69
Code page
Currently enabled code page
Printer information (When n = 65, 66, 67, 69) consist of [Header ~ NULL] data as shown below:
Transmitted data
Hex
Decimal
Amount of data
Header
5FH
95
1byte
Printer information
Depends on the model
Depends on the model
0-15 bytes
NUL
00H
0
1byte
■ The firmware version can be confirmed by self test printing.
BIXOLON
- 112 -
SRP-350/352plusII
Differences:
■
The printer ID is shown according to printer models as follows:
Printer ID
SRP-350plusII
SRP-352plusII
1(Printer model ID)
0x20
0x20
Type ID varies depending on functions the printer supports as follows:
- 0x01 (Multi-byte character)
- 0x02 (Autocutter)
2(Type ID)
- 0x03 (Autocutter + Multi-byte character)
- 0x04 (Customer display)
- 0x05 (Multi-byte character + Display)
- 0x07 (Customer display + Autocutter + Multi-byte Character)
3(Printer feature ID)
0x63
66(Manufacturer)
67(Printer model)
69(Language of Font)
Rev. 1.01
0x63
BIXOLON
SRP-350plusII
SRP-352plusII
Code page currently being used. Refer to cod page setting command, ESC t.
BIXOLON
- 113 -
SRP-350/352plusII
GS L
Function:
Code:
Set left margin
ASCII
Hex
Decimal
GS
1D
29
L
4C
76
nL
nL
nL
nH
nH
nH
Range:
0 ≤ nL ≤ 255, 0 ≤ nH ≤ 255
Default:
(nL + nH x 256)=0 (nL=0, nH=0)
Description:
This command sets the left margin specified to [(nL + nH x 256) x (horizontal motion units)].
Remarks:
■
The left margin is not effective in page mode. If the left margin is enabled in page mode, the setting is available when
the printer returns to standard mode.
■ When the setting is beyond the printable area, the left margin is automatically set to the maximum value of the
printable area.
■ Since the left margin is the same as the leftmost side of the printable area, the left side of the printable area is
changed according to the left margin specified.
■ The setting of this command remains effective until ESC @, printer reset or power cycling is executed.
Printable area
Left margin
Differences:
Rev. 1.01
Printing area width
None
BIXOLON
- 114 -
SRP-350/352plusII
GS V
Function:
Select cut mode and cut paper
Code:
①
②
ASCII
Hex
Decimal
ASCII
Hex
Decimal
GS
1D
29
GS
1D
29
V
56
86
V
56
86
m
m
m
m
m
m
n
n
n
② m=65, 66, 0 ≤ n ≤ 255
Range:
① m=0, 1, 48, 49
Default:
None
Description:
This command cuts paper in the specified mode as follows.
m
Function
0,48
①
Executes a partial cut (one point left uncut)
1,49
②
65
Feeds paper to (cutting position + n × vertical motion unit) and executes a partial cut(one point left uncut)
Remarks:
For ①
■ If an auto cutter is not provided, this command is ignored command is executed.
For ②
■ When n = 0, the printer feeds the paper to the cutting position and cuts it.
■ If an auto cutter is not provided, the printer only feeds the paper for specified amount.
■ Vertical motion unit is used for calculating a paper feed amount.
■ Cutting mode is changed only by setting MSW5-1.
Differences:
None
Rev. 1.01
BIXOLON
- 115 -
SRP-350/352plusII
GS W
Function:
Code:
Set printing area width
ASCII
Hex
Decimal
GS
1D
29
W
57
87
nL
nL
nL
nH
nH
nH
Range:
0 ≤ nL ≤ 255, 0 ≤ nH ≤ 255
Default:
■
Description:
This command sets the printing area width to [(nL + nH x 256) x (horizontal motion units)].
Remarks:
■
SRP-350plusII:
(nL + nH x 256)=512 (nL=0, nH=2) (When 80mm width of paper used)
■ SRP-352plusII:
(nL + nH x 256)=576 (nL=64, nH=2) (When 80mm width of paper used)
The printing area width is not effective in page mode. If the printing area width is enabled in page mode, the setting is
available when the printer returns to standard mode.
■ When (left margin + printing area width) exceeds the printable area, the printing area width is automatically set to
(printing area width - left margin).
■ The setting of this command remains effective until ESC @, printer reset or power cycling is executed.
Printable area
Left margin
Differences:
Rev. 1.01
Printing area width
None
BIXOLON
- 116 -
SRP-350/352plusII
GS ^
Function:
Execute macro
Code:
ASCII
Hex
Decimal
Range:
0 ≤ r ≤ 255
0 ≤ t ≤ 255
m=0, 1
Default:
None
Description:
■
This command executes a macro using parameters as following:
• r specifies the number of times to execute the macro.
• t specifies the waiting time before the macro is executed.
• m specifies macro executing mode as shown below.
m
Function
0
Executes the macro r times continuously at the interval specified by t.
The printer waits for the paper FEED button to be pressed for the time specified by t. The macro is
1
executed once when the button is pressed. This operation is repeated r times.
Remarks:
■
■
■
The macro is defined by GS:
If the macro is not defined or r = 0, the command is ignored.
The macro function is useful to print the same data repeatedly.
Differences:
None
Rev. 1.01
GS
1D
29
^
5E
94
r
r
r
t
t
t
m
m
m
BIXOLON
- 117 -
SRP-350/352plusII
GS a
Function:
Enable/Disable Automatic Status Back (ASB)
Code:
ASCII
Hex
Decimal
Range:
0 ≤ n ≤ 255
Default:
n=0
Description:
■
Remarks:
■
Rev. 1.01
GS
1D
29
a
61
97
n
n
n
This enables or disables ASB (Automatic Status Back) according to n.
• ASB is enabled when n > 0.
ASB is the function that transmit the printer status such as cover open/close and Online/Offline] continuously at the
time interval specified regardless of the status change if ASB is enabled. Using this ASB function, the host can check
to see if the printer is running properly.
■ Once ASB has been enabled, the printer continues to transmit the current printer status at the specified interval until
ASB is disabled.
■ When n = 0, ASB is disabled. The printer stops transmitting the status.
■ With parallel and USB interface, the printer status is transmitted whenever the host computer changes to the reverse
mode regardless of the printer status change. It is recommended that the periodic time interval at which the host
changes to reverse mode is more than 500ms in order to receive the correct status.
■ With serial interface, ASB status is transmitted continuously at the interval of 1 sec even if the status is not changed.
■ The setting of this command remains effective until ESC @, printer reset or power cycling is executed.
BIXOLON
- 118 -
SRP-350/352plusII
■
The printer information transmitted is comprised of 4 bytes as follows:
• First byte(printer information)
Bit
Off/On
Hex
Decimal
Function
0
Off
00
0
Not used. Fixed to Off
1
Off
00
0
Not used. Fixed to Off
Off
00
0
Drawer kick-out connector pin 3 is LOW
2
On
04
4
Drawer kick-out connector pin 3 is HIGH
Off
00
0
On-line
3
On
08
8
Off-line
4
On
10
16
Not used. Fixed to On
Off
00
0
Cover is close
5
On
20
32
Cover is open
Off
00
0
Paper is not being fed by the paper feed button
6
On
40
64
Paper is being fed by the paper feed butto
7
Off
00
0
Not used. Fixed to Off
Second byte(printer information)
Bit
Off/On
Hex
Decimal
0
Off
00
0
1
Off
00
0
Off
00
0
2
On
04
4
Off
00
0
3
On
08
8
4
Off
00
0
Off
00
0
5
On
20
32
Off
00
0
6
On
40
64
7
Off
00
0
•
-
Rev. 1.01
Function
Not used. Fixed to Off
Not used. Fixed to Off
No mechanical error
Mechanical error
No auto cutter error
Auto cutter error occurred
Not used. Fixed to Off
No unrecoverable error
Unrecoverable error
No automatically recoverable error
Automatically recoverable error occurred
Not used. Fixed to Off
If mechanical error (bit 2) or auto-cutter error (bit 3) occurs due to paper jams or the like, it is possible to recover
by correcting a cause of the error and executing ENQ in real time mode.
BIXOLON
- 119 -
SRP-350/352plusII
-
If an unrecoverable error (bit 5) occurs, turn off the power as soon as possible.
Third byte (paper sensor information)
Bit
Off/On
Hex
Decimal
Off
00
0
0,1
On
03
3
Off
00
0
2,3
On
0C
12
4
Off
00
0
5
Off
00
0
6
Off
00
0
7
Off
00
0
Function
Paper near end sensor: paper adequate
Paper near end sensor: paper near end
Paper end sensor: paper present
Paper end sensor: no paper present
Not used. Fixed to Off
Not used. Fixed to Off
Not used. Fixed to Off
Not used. Fixed to Off
Fourth byte (paper sensor information)
Bit
Off/On
Hex
Decimal
0
On
01
1
1
On
02
2
2
On
04
4
3
On
08
8
4
Off
00
0
5
Off
00
0
6
Off
00
0
7
Off
00
0
Not used. Fixed to On
Not used. Fixed to On
Not used. Fixed to On
Not used. Fixed to On
Not used. Fixed to Off
Not used. Fixed to Off
Not used. Fixed to Off
Not used. Fixed to Off
•
•
Differences:
Rev. 1.01
Function
None
BIXOLON
- 120 -
SRP-350/352plusII
GS f
Function:
Code:
Select font for HRI characters
ASCII
Hex
Decimal
GS
1D
29
f
66
102
n
n
n
Range:
n = 0, 1, 48, 49
Default:
n=0
Description:
This command selects a font for the HRI(Human Readable Interpretation) characters used when printing a bar code,
using n as follows:
n
Font
0, 48
Font A
1, 49
Font B
Remarks:
■
■
■
Differences:
None
Rev. 1.01
The setting of this command is applied to only HRI characters.
The printing position of HRI characters are specified by GS H.
The configurations of Font A and B vary depending on the printer model.
BIXOLON
- 121 -
SRP-350/352plusII
GS h
Function:
Selects bar code height
Code:
ASCII
Hex
Decimal
Range:
1 ≤ n ≤ 255
Default:
n = 162
Description:
This command sets the height of the bar code to n dots.
Remarks:
■
■
Differences:
Unit of one dot:
■ SRP-350plusII: 0.141mm(1/180 inch)
■ SRP-352plusII: 0.125mm(1/203 inch)
Rev. 1.01
GS
1D
29
h
68
104
n
n
n
The unit of n depends on the printer model.
The setting of this command remains effective until ESC @, printer reset or power cycling is executed.
BIXOLON
- 122 -
SRP-350/352plusII
GS k
Function:
Print bar code
Code:
①
②
ASCII
Hex
Decimal
ASCII
Hex
Decimal
GS
1D
29
GS
1D
29
k
6B
107
k
6B
107
m
m
m
m
m
m
Range:
①0≤m≤6
② 65 ≤ m ≤ 73
K, m, n depend on the barcode system
Default:
None
Description:
■
NUL
NUL
NUL
d1...dn
d1...dn
d1...dn
This command selects a bar code system and prints the bar code.
• k indicates the number of bytes of bar code data.
• n specifies the number of bytes of bar code data.
• d specifies the character code data of the bar code data to be printed.
For range ①
m
0
1
2
3
Rev. 1.01
d1...dk
d1...dk
d1...dk
n
n
n
Bar Code System
UPC-A
UPC-E
JAN13(EAN)
JAN8(EAN)
Range of k
11 ≤ k ≤ 12
11 ≤ k ≤ 12
12 ≤ k ≤ 13
7≤k≤8
4
CODE39
1≤k
5
ITF
1 ≤ k (even number)
6
CODABAR
1≤k
BIXOLON
Range of d
48 ≤ d ≤ 57
48 ≤ d ≤ 57
48 ≤ d ≤ 57
48 ≤ d ≤ 57
48 ≤ d ≤ 57, 65 ≤ d ≤ 90,
d=32,36,37,43,45,46,47
48 ≤ d ≤ 57
48 ≤ d ≤ 57, 65 ≤ d ≤ 68,
d=36,43,45,46,47,58
- 123 -
SRP-350/352plusII
For range ②
m
65
66
67
68
Bar Code System
UPC-A
UPC-E
JAN13(EAN)
JAN8(EAN)
Range of k
11 ≤ n ≤ 12
11 ≤ n ≤ 12
12 ≤ n ≤ 13
7≤n≤8
69
CODE39
1 ≤ n ≤ 255
70
ITF
1 ≤ n ≤ 255 (even number)
71
CODABAR
1 ≤ n ≤ 255
72
73
CODE93
CODE128
1 ≤ n ≤ 255
2 ≤ n ≤ 255
Remarks:
■
■
Differences:
None
Rev. 1.01
Range of d
48 ≤ d ≤ 57
48 ≤ d ≤ 57
48 ≤ d ≤ 57
48 ≤ d ≤ 57
48 ≤ d ≤ 57, 65 ≤ d ≤ 90,
d=32,36,37,43,45,46,47
48 ≤ d ≤ 57
48 ≤ d ≤ 57, 65 ≤ d ≤ 68,
d=36,43,45,46,47,58
0 ≤ d ≤ 127
0 ≤ d ≤ 127
The bar code width exceeding the print area can not be specified.
Except for character size and upside-down printing mode, none of print mode such as emphasized, double-strike, etc,
affects the printing of the barcode.
■ The quiet zone of the bar code (left and right spaces of the bar code) should be considered when using this
command.
BIXOLON
- 124 -
SRP-350/352plusII
GS r
Function:
Code:
Transmit status
ASCII
Hex
Decimal
GS
1D
29
r
72
114
n
n
n
Range:
n = 1, 2, 49, 50
Default:
None
Description:
The command transmits the status specified by n as follows:
n
Function
1, 49
Transmits paper sensor status
2, 50
Transmits drawer kick-out connector status
Remarks:
■
■
Rev. 1.01
The status is one byte.
The status to be transmitted is as follows:
• Paper sensor status (n=1, 49):
Bit
Off/On
Hex
Decimal
Off
00
0
0, 1
On
03
3
Off
00
0
2, 3
On
0C
12
4
Off
00
0
5
Off
00
0
6
Off
00
0
7
Off
00
0
Function
Paper near-end sensor: Paper adequate
Paper near-end sensor: Paper near end
Paper end sensor: Paper present
Paper end sensor: Paper not present
Fixed
Reserved
Reserved
Fixed
BIXOLON
- 125 -
SRP-350/352plusII
Bits 2 and 3: This command can not be executed
status of bit 2 (1) and bit 3 (1) is not transmitted.
• Drawer kick-out connector status (n=2, 50):
Bit
Off/On
Hex
Decimal
Off
00
0
0
On
01
1
1
Off
00
0
2
Off
00
0
3
Off
00
0
4
Off
00
0
5
Off
00
0
6
Off
00
0
7
Off
00
0
■
Differences:
Rev. 1.01
when the printer is offline due to the lack of paper. Therefore, the
Function
Drawer kick-out connector pin 3 is LOW
Drawer kick-out connector pin 3 is HIGH
Reserved
Reserved
Reserved
Fixed
Reserved
Reserved
Fixed
This command can be executed in real-time mode using DLE.
None
BIXOLON
- 126 -
SRP-350/352plusII
GS v 0
Function:
Code:
Print raster bit image
ASCII
Hex
Decimal
GS
1D
29
v
76
118
0
30
48
m
m
m
xL xH
xL xH
xL xH
Range:
0 ≤ m ≤ 3, 48 ≤ m ≤ 51
1 ≤ (xL + xH x 256) ≤ 128 (0 ≤ xL ≤ 128, xh=0)
1 ≤ (yL + yH x 256) ≤ 4095 (0 ≤ yL ≤ 255, 0 ≤ yH ≤ 15)
0 ≤ d ≤ 255
k = (xL + xH x 256) x (yL + yH x 256)
Default:
None
Description:
■
Remarks:
■
Rev. 1.01
yL yH d1...dk
yL yH d1...dk
yL yH d1...dk
This command prints a raster bit image according to the mode defined by m.
DPI : Dots per Inch (25.4mm)
m
Mode
Vertical dot density (DPI)
Horizontal dot density (DPI)
0, 48
Normal
180
180
1, 49
Double-width
180
90
2, 50
Double-height
90
180
3, 51
Quadruple
90
90
• xL, xH specifies (xL + xH x 256) byte(s) in the horizontal direction for the bit image.
• yL, yH specifies (yL + yH x 256) dot(s) in the vertical direction for the bit image.
• d specifies the definition data of the bit image data.
In standard mode, this command is effective when the printer buffer is empty and the printer is in the beginning of the
line. If the buffer is not empty, after processing m, the printer treats the following data as normal data.
■ In page mode, the bit image is stored in the print buffer, not being printed.
■ None of the print modes such as emphasized, double-strike, etc, affects the printing of the bit image.
■ The default dot density set by GS L is applied to printing of the bit image.
BIXOLON
- 127 -
SRP-350/352plusII
Differences:
■
SRP-350plusII:
m
0, 48
1, 49
2, 50
3, 51
■
Vertical dot density (DPI)
180
180
90
90
Vertical dot density (DPI)
203
203
203/2
203/2
DPI : Dots per Inch (25.4mm)
Horizontal dot density (DPI)
203
203/2
203
203/2
SRP-352plusII:
m
0, 48
1, 49
2, 50
3, 51
Rev. 1.01
Mode
Normal
Double-width
Double-height
Quadruple
DPI : Dots per Inch (25.4mm)
Horizontal dot density (DPI)
180
90
180
90
Mode
Normal
Double-width
Double-height
Quadruple
BIXOLON
- 128 -
SRP-350/352plusII
GS w
Function:
Code:
Set bar code width
ASCII
Hex
Decimal
Range:
2≤n≤6
Default:
n=3
Description:
■
Remarks:
■
Rev. 1.01
GS
1D
29
w
77
119
n
n
n
This command sets the horizontal size of the bar code, using n as follows:
Binary-level bar code
Multi-level bar code module
n
width (mm)
Thin element width (mm)
Thick element width (mm)
2
0.282
0.282
0.706
3
0.423
0.423
1.129
4
0.564
0.564
1.411
5
0.706
0.706
1.834
6
0.847
0.847
2.258
• n specifies the bar code module width.
The setting of this command is effective for the following bar codes:
• Multi-level bar codes (UPC-A, UPC-E, JAN13, HAN8, CODE93, CODE128)
• Binary-level bar codes (CODE39, ITF, CODABAR)
■ The setting of this command remains effective until ESC @, printer reset or power cycling is executed.
BIXOLON
- 129 -
SRP-350/352plusII
Differences:
■
■
Rev. 1.01
SRP-350plusII:
Multi-level bar code module
n
width (mm)
2
0.282
3
0.423
4
0.564
5
0.706
6
0.847
Binary-level bar code
Thin element width (mm)
Thick element width (mm)
0.282
0.706
0.423
1.129
0.564
1.411
0.706
1.834
0.847
2.258
SRP-352plusII:
Multi-level bar code module
n
width (mm)
2
0.250
3
0.375
4
0.500
5
0.625
6
0.750
Binary-level bar code
Thin element width (mm)
Thick element width (mm)
0.250
0.625
0.375
1.000
0.500
1.250
0.625
1.625
0.750
2.000
BIXOLON
- 130 -
SRP-350/352plusII
BS M
Function:
Code:
Select device font type
ASCII
Hex
Decimal
BS
08
08
M
4D
77
Range:
65 ≤ m ≤ 67 ( m = 65,66,67)
Default:
n=0
Description:
■
n
n
n
m
m
m
This command selects print mode(s) with bits having following meanings:
Bit
Off/On
Hex
Decimal
Function
Off
00
0
Resident ASCII font selected
0
On
01
1
Customized ASCII font selected
Off
00
0
Resident codepage font selected
1
On
02
2
Customized character font selected
m
65
66
67
Function ( Select font type )
Font A (12x24)
Font B (9x17)
Font C (9x24)
■ The printer supports 3 font types by selecting m function.
Remarks:
■
Differences:
None
Rev. 1.01
The setting of this command remains effective until ESC !, ESC @, printer reset or power cycling is executed.
BIXOLON
- 131 -
SRP-350/352plusII
BS V
Function :
Select cut mode and cut paper
Code :
①
②
ASCII
Hex
Decimal
ASCII
Hex
Decimal
BS
08
08
BS
08
08
V
56
86
V
56
86
m
m
m
m
m
m
n
n
n
② m=65, 66, 0 ≤ n ≤ 255
Range:
① m=0, 1, 48, 49
Default:
None
Description :
This command cuts paper in the specified mode as follows.
Remarks :
For ①
■ If an auto cutter is not provided, this command is ignored command is executed.
For ②
■ When n = 0, the mechanism feeds the paper to the cutting position and cuts it.
■ If an auto cutter is not provided, the mechanism only feeds the paper for specified amount.
Rev. 1.01
BIXOLON
- 132 -
SRP-350/352plusII
■
Differences:
Rev. 1.01
Vertical motion unit is used for calculating a paper feed amount.
m
Function
0,48
Executes a partial cut (one point left uncut)
①
1,49
Executes a full cut (cuts the paper completely)
Feeds paper to (cutting position + n × vertical motion unit) and executes a partial cut
65
(one point left uncut)
②
Feeds paper to (cutting position + n × vertical motion unit) and executes a full cut
66
(cuts the paper completely)
None
BIXOLON
- 133 -
SRP-350/352plusII
BS ^ P
Function:
Code:
Set power saving mode
ASCII
Hex
Decimal
BS
08
08
^
5E
94
P
50
84
fn
fn
fn
Range:
None
Default:
None
Description:
■
■
Set the power saving mode for low power consumption.
When the printer is entered power saving mode, printer is wait external interrupt.
Remarks:
■
If external interrupt is occurred, printer is wake up.
• Communication(Serial, Parallel, USB), Cover sensor, Feed switch.
Differences:
None
Rev. 1.01
BIXOLON
- 134 -
SRP-350/352plusII
<Function 48> BS ^ P fn (fn=0,48)
Code :
ASCII
Hex
Decimal
BS
08
08
^
5E
94
P
50
84
fn
fn
fn
m
m
m
t
t
t
Range:
fn=0,48, 0 ≤ m ≤ 1
5 ≤ t ≤ 255
Default:
m = 1, t = 20
Description :
■
Set the power saving mode and time to change the sataus of printer.
Remarks :
■
■
■
The m=0 : power saving mode disable.
The m=1 : power saving mode enable.
The power saving set time is [t x 1s] and the default time is 20 sec.
• If n is smaller than 5 the power saving time is set to defaut [20 x 1s].
Differences:
None
Rev. 1.01
BIXOLON
- 135 -
SRP-350/352plusII
<Function 49> BS ^ P fn (fn=1,49)
Code:
ASCII
Hex
Decimal
BS
08
08
^
5E
94
P
50
84
fn
fn
fn
Range:
fn=1,49
Default:
None
Description:
■
Read the power saving mode satatus and sleep time.
Remarks:
■
Power saving data is consist of [Header ~ NULL] data as shown below:
Transmitted data
Hex
Decimal
Header
5FH
95
Power saving mode
Depends on the setting
Depends on the setting
Power saving time
Depends on the setting
Depends on the setting
NUL
00H
0
Differences:
Rev. 1.01
Amount of data
1byte
1byte
1byte
1byte
None
BIXOLON
- 136 -