DSC Power8 PC5OO5 Installation manual

Programming
Worksheets
®
Power8
TM
S E C U R I T Y
S Y S T E M
PC5005 Version 3.2
DLS-3 v1.3 and higher
FCC Compliance Statement:
CAUTION: Changes or modifications not expressly approved by Digital
Security Controls Ltd. could void your authority to use this equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Re-orient the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/television technician for help.
The user may find the following booklet prepared by the FCC useful: “How to
Identify and Resolve Radio/Television Interference Problems”. This booklet is
available from the U.S. Government Printing Office, Washington D.C. 20402,
Stock # 004-000-00345-4.
IMPORTANT INFORMATION
This equipment complies with Part 68 of the FCC Rules. On the side of
this equipment is a label that contains, among other information, the FCC
registration number of this equipment.
Notification to Telephone Company The customer shall notify the telephone company of the particular line to which the connection will be
made, and provide the FCC registration number and the ringer equivalence of the protective circuit.
FCC Registration Number: F53CAN-34330-AL-E
Ringer Equivalence Number: 0.1B
USOC Jack: RJ-31X
Telephone Connection Requirements Except for the telephone company
provided ringers, all connections to the telephone network shall be made
through standard plugs and telephone company provided jacks, or equivalent,
in such a manner as to allow for easy, immediate disconnection of the terminal
equipment. Standard jacks shall be so arranged that, if the plug connected
thereto is withdrawn, no interference to the operation of the equipment at the
customer’s premises which remains connected to the telephone network shall
occur by reason of such withdrawal.
Incidence of Harm Should terminal equipment or protective circuitry cause
harm to the telephone network, the telephone company shall, where practicable, notify the customer that temporary disconnection of service may be
required; however, where prior notice is not practicable, the telephone company may temporarily discontinue service if such action is deemed reasonable
in the circumstances. In the case of such temporary discontinuance, the telephone company shall promptly notify the customer and will be given the opportunity to correct the situation.
Additional Telephone Company Information The security control panel must
be properly connected to the telephone line with a USOC RJ-31X telephone
jack.
The FCC prohibits customer-provided terminal equipment be connected to
party lines or to be used in conjunction with coin telephone service. Interconnect rules may vary from state to state.
Changes in Telephone Company Equipment or Facilities The telephone
company may make changes in its communications facilities, equipment,
operations or procedures, where such actions are reasonably required and
proper in its business. Should any such changes render the customer’s terminal equipment incompatible with the telephone company facilities the customer shall be given adequate notice to the effect modifications to maintain
uninterrupted service.
Ringer Equivalence Number (REN) The REN is useful to determine the quantity of devices that you may connect to your telephone line and still have all of
those devices ring when your telephone number is called. In most, but not all
areas, the sum of the RENs of all devices connected to one line should not
exceed five (5.0). To be certain of the number of devices that you may connect
to your line, you may want to contact your local telephone company.
Equipment Maintenance Facility If you experience trouble with this telephone
equipment, please contact the facility indicated below for information on
obtaining service or repairs. The telephone company may ask that you disconnect this equipment from the network until the problem has been corrected or
until you are sure that the equipment is not malfunctioning.
Digital Security Controls Ltd. 160 Washburn St., Lockport, NY 14094
Page references below are to the accompanying Installation Manual. The programming sections are in numeric order in the
present publication.
Power864 Programming Guidelines
Item
Page
Section
Zone Definitions
19
[001]-[002]
Zone Attributes
29
[101]-[132]
Zone Programming
Page
Section
First, Second, Third Phone Numbers
31
[301]-[303]
Call Waiting Cancel String
31
[304]
System Account Number
31
[310]
31
[311]-[318]
App . A
[320]-[349]
Pager
Adding Wireless Zones
Enrolling Wireless Serial Numbers
Item
PC5132 Manual [804]
Partition Account Numbers
Partition Selection Mask
30
[201]
Assigning Zones to Partitions
30
[202]-[261]
Communicator Format Options
34
[350]
Zone Definitions
19
[001]-[002]
Communicator Call Direction
36
[351]-[376]
Zone Attributes
29
[101]-[132]
Residential Dial
First, Second, Third Phone Numbers
31
[301]-[303]
Call Waiting Cancel String
31
[304]
System Account Number
31
[310]
Partition Account Numbers
31
[311]-[318]
App . A
[320]-[349]
Adding AML Zones
Enrolling Wireless Serial Numbers
PC5100 Manual [805]
Reporting Codes
Partition Selection Mask
30
[201]
Assigning Zones to Partitions
30
[202]-[261]
Zone Definitions
19
[001]-[002]
Reporting Codes
Zone Attributes
29
[101]-[132]
Communicator Format Options
34
[350]
Communicator Call Direction
36
[351]-[376]
Adding Keypad Zones
Test Transmission
Keypad Assignment
6
[000]
Keypad Zone Assignment
28
[020]
Test Transmission Reporting Codes
App . A
[348]
Partition Selection Mask
30
[201]
Communication Variables
37
[377]
Assigning Zones to Partitions
30
[202]-[261]
Test Transmission Time of Day
37
[378]
Wiring Keypad Zones
8
2.11
Sixth System Option Code, Option [1]
27
[018]
[015]
2 Wire Smoke Detectors
Telephone Line Monitoring (TLM)
Programmable Output Options
21
[009]
Third System Option Code, Options [7, 8]
25
Priority Alarm/Restore Reporting Codes
31
[329]
Communication Variables
37
[377]
Zone Wiring - 2 Wire Smoke Detectors
7
2.10
Reporting Codes
App . A
[345, 364]
Sixth System Option Code - Option [6]
27
[018]
PGM1 and PGM2 Outputs
21
[009]
Zone Attributes
29
[101]-[132]
PGM3 to PGM10 Outputs
21
[010]
Cross Zone / Police Code Timer
29
[176]
PGM11 to PGM14 Outputs
21
[011]
Miscellaneous Alarm Reporting Codes
31
[328]
PGM Output Attributes
41
[501]-[514]
PGM Output Partition Assignment
42
[551]-[564]
Keypad Assignment
6
[000]
Partition & Zone Programming
30
[202]-[261]
First Downloading Option Code
41
[401]
Partition 1-8 Account Codes
31
[311]-[317]
Downloading Computer Phone Number
41
[402]
Programming Access Codes
13
4.2
Downloading Access Code
41
[403]
Panel Identification Code
41
[404]
Cross Zones
PGM Outputs
Additional Partitions
Local System
Downloading
First Communicator Option Code, Option [1]
38
[380]
Double Call Timer
41
[405]
Third System Option Code, Option [7]
25
[015]
Number of Rings to Answer
41
[406]
SIA Communications
Bell Output Options
First, Second, Third Phone Numbers
31
[301]-[304]
System Times
20
[005], [009]
Call Waiting Cancel String
31
[304]
First System Option Code, Option [8]
24
[013]
System Account Code
31
[310]
Second System Option Code, Options [1]-[5]
24
[014]
Partition Account Numbers
31
[311]-[318]
Automatic Arming
Reporting Codes
App . A
[320]-[349]
Automatic Arming Schedule
30
[181]-[188]
Communicator Format Options
34
[350]
Postpone Auto Arming Timer
29
[175]
Communicator Call Direction
36
[351]-[376]
Auto-Arming Pre-Alert
30
[199]
First, Second, Third Communicator Options
38
[380]-[382]
Fifth System Option Code, Option [1]
26
[017]
Contact ID Communications
No Activity Arming
First, Second, Third Phone Numbers
31
[301]-[303]
No Activity Arming Timers
30
[191]-[198]
Call Waiting Cancel String
31
[304]
No Activity Arming Pre-Alert
30
[190]
System Account Number
31
[310]
International Programming
31
[311]-[318]
Automatic Clock Adjust
42
[700]
App . A
[320]-[349]
International Option Codes
43
[701]-[702]
Delay Between Dialing Attempts
44
[703]
44
[801]-[851]
44
[901]-[999]
Partition Account Numbers
Reporting Codes
Communicator Format Options
34
[350]
Communicator Call Direction
36
[351]-[376]
First, Second, Third Communicator Options
38
[380]-[382]
Module Programming
Module Programming
Special Installer Functions
Special Installer Functions
Ta ble of Contents
Section 1: For the Record
1
Account Information .......................................................... 1
Call Direction Options ....................................................... 16
Zone Programming Summary ............................................. 2
Communicator Options..................................................... 18
Section 2: Keypad Programming
3
Section 3: Basic Programming
4
Zone Definitions ................................................................. 4
[377] Communication Variables ........................................ 18
LINKS1000 Preambles ....................................................... 19
Section 7: Downloading Options
20
System Times and Codes .................................................... 5
Section 8: Programmable Output Programming
21
Programmable Output Attributes ...................................... 21
Programmable Output Options ........................................... 5
PGM Output Partition Assignment .................................... 22
Other System Options......................................................... 6
Keypad Zone Assignments .................................................. 7
Zone Loop Response Option Code ...................................... 7
Section 4: Advanced System Programming
8
Zone Attributes .................................................................. 8
Section 9: International Programming
23
Section 10: Module Programming
24
Section 11: Special Installer Functions
25
System Timers .................................................................... 9
Appendix A: Programming LCD5500Z/ Keypads
26
LCD5500Z v2.x and Lower Keypads .................................. 26
Automatic Arming Schedule ............................................. 10
ASCII Characters .............................................................. 28
Section 5: Partition and Zone Programming
11
[201] Partition Selection Mask .......................................... 11
LCD5500Z v3.0 and Higher Keypads ................................. 28
Assigning Zones to Partitions ............................................ 11
Section 6: Communicator Programming
13
Telephone Numbers ......................................................... 13
[350] Communicator Format Options ............................... 16
ASCII Characters .............................................................. 32
Appendix B: Programming LCD5501Z Keypads
33
Programming Keypad Options........................................... 33
Programming Door Chime Options ................................... 34
S e c ti o n 1 : Fo r th e R e co rd
Account Information
Customer:___________________________________________________________________________________________________
Address:____________________________________________________________________________________________________
Telephone:______________________________________________Installation Date:_____________________________________
Installer’s Code:______________________________________________________________________________________________
Module and Keypad Information
Module Name
Description
Location
PC5005
Main Panel
I________________________________________________________________________________________________________________I
PC5100
Addressable Zone Expander
I________________________________________________________________________________________________________________I
PC5132
Wireless Receiver 1
I________________________________________________________________________________________________________________I
PC5132
Wireless Receiver 2
I________________________________________________________________________________________________________________I
PC5132
Wireless Receiver 3
I________________________________________________________________________________________________________________I
PC5132
Wireless Receiver 4
I________________________________________________________________________________________________________________I
PC5200
Power Supply Module 1
I________________________________________________________________________________________________________________I
PC5200
Power Supply Module 2
I________________________________________________________________________________________________________________I
PC5200
Power Supply Module 3
I________________________________________________________________________________________________________________I
PC5200
Power Supply Module 4
I________________________________________________________________________________________________________________I
PC5204
Power Supply Output Module
I________________________________________________________________________________________________________________I
PC5208
Low-Current Output Module
I________________________________________________________________________________________________________________I
PC5936
Audio Interface Module
I________________________________________________________________________________________________________________I
Escort5580
Voice Prompt Module
I________________________________________________________________________________________________________________I
PC5400
Serial Printer Module
I________________________________________________________________________________________________________________I
PC5400
DVACS Module
I________________________________________________________________________________________________________________I
LINKS1000
Cellular Communicator
I________________________________________________________________________________________________________________I
LINKS2X50
Long Range Radio
I________________________________________________________________________________________________________________I
Skyroute
Transceiver
I________________________________________________________________________________________________________________I
Keypads
Keypad Type
Location
Keypad 1
I_____________________________________________I
I________________________________________________________________________________________________________________I
Keypad 2
I_____________________________________________I
I________________________________________________________________________________________________________________I
Keypad 3
I_____________________________________________I
I________________________________________________________________________________________________________________I
Keypad 4
I_____________________________________________I
I________________________________________________________________________________________________________________I
Keypad 5
I_____________________________________________I
I________________________________________________________________________________________________________________I
Keypad 6
I_____________________________________________I
I________________________________________________________________________________________________________________I
Keypad 7
I_____________________________________________I
I________________________________________________________________________________________________________________I
Keypad 8
I_____________________________________________I
I________________________________________________________________________________________________________________I
1
Zone Programming Summary
Zone programming can be found in sections [001] - [002], [101] - [132], [020] and [202] - [261]. Use this area to record a summary of your zone programming. Refer to, for instructions on programming zone labels.
System
Zone Label
Zone
Zone
Zone Attributes*
Type
1 2 3 4 5 6 7 8
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
*Zone Attributes:
Option 1: Audible/Silent
Option 2: Steady/Pulsed
Option 3: Chime
Option 4: Bypass
2
Option 5: Force Arming
Option 6: Swinger Shutdown
Option 7: Transmission Delay
Option 8: Wireless
Option 9: Cross Zone
9
Serial Number
Partitions
(Wireless)
1 2 3 4 5 6 7 8
Section 2: Keypad Programming
[000] Keypad Enrollment
NOTE: This must be done at each keypad requiring programming.
[0] Slot address [Valid entries are 0-8 for the partition, 1-8 for the slot. (e.g., to enroll a keypad in partition 3 and slot 1, enter (31)]
[1] Function Key 1 Assignment (Valid entries are 00-32)
[2] Function Key 2 Assignment (Valid entries are 00-32)
[3] Function Key 3 Assignment (Valid entries are 00-32)
[4] Function Key 4 Assignment (Valid entries are 00-32)
[5] Function Key 5 Assignment (Valid entries are 00-32)
Function Key Options:
00
01
02
03
04
05
06
07
08
09
10
Not used
Select Partition 1
Select Partition 2
Stay Arm
Away Arm
[*][9] No-Entry Arm
[*][4] Chime On / Off
[*][6][——][4] System Test
[*][1] Bypass Mode
[*][2] Trouble Display
[*][3] Alarm Memory
Partition/
Slot
LCD 5501/LED defaults11
LCD Defaults
18
11 [*][5] Access Code Programming
12 [*][6] User Functions
13 Command Output #1 [*][7][1]
14 Command Output #2 [*][7][2]/Sensor Reset
15 General Voice Prompted Help
16 [*][0] Quick Exit
17 [*][1] Reactivate Stay/Away Zones
18 Identified Voice Prompted Help
19 Command Output 3 [*][7][3]
20 For Future Use
21 Command Output 4 [*][7][4]
Function
Key 1
03
Function
Key 2
04
Function
Key 3
06
03
04
06
22 Active Camera Monitor Selection
23 Bypass Recall
24 Recall Bypass Group
25 For Future Use
26 For Future Use
27 Select Partition 3
28 Select Partition 4
29 Select Partition 5
30 Select Partition 6
31 Select Partition 7
32 Select Partition 8
Function
Key 4
14
14
Function
Key 5
16
16
KEYPAD 1
I________I________I
I________I________I
I________I________I
I________I________I
I________I________I
I________I________I
KEYPAD 2
I________I________I
I________I________I
I________I________I
I________I________I
I________I________I
I________I________I
KEYPAD 3
I________I________I
I________I________I
I________I________I
I________I________I
I________I________I
I________I________I
KEYPAD 4
I________I________I
I________I________I
I________I________I
I________I________I
I________I________I
I________I________I
KEYPAD 5
I________I________I
I________I________I
I________I________I
I________I________I
I________I________I
I________I________I
KEYPAD 6
I________I________I
I________I________I
I________I________I
I________I________I
I________I________I
I________I________I
KEYPAD 7
I________I________I
I________I________I
I________I________I
I________I________I
I________I________I
I________I________I
KEYPAD 8
I________I________I
I________I________I
I________I________I
I________I________I
I________I________I
I________I________I
3
Section 3: Basic Programming
Zone Definitions
00
01
02
03
04
05
06
07
08
09
10
11
Null Zone (Not Used)
Delay 1*
Delay 2*
Instant*
Interior*
Interior, Stay/Away*
Delay, Stay/Away*
Delayed 24 Hour Fire (Hardwired)**
Standard 24 Hour Fire (Hardwired)
24 Hour Supervisory
24 Hour Supervisory Buzzer*
24 Hour Burglary*
12
13
14
15
16
17
18
19
20
21
22
24 Hour Holdup*
24 Hour Gas*
24 Hour Heating*
24 Hour Auxiliary*
24 Hour Panic*
24 Hour Emergency*
24 Hour Sprinkler*
24 Hour Water*
24 Hour Freeze*
24 Hour Latching Tamper*
Momentary Keyswitch Arm*
23 Maintained Keyswitch Arm*
24 LINKS1000 Answer*
25 Interior Delay*
26 24 Hour Non-alarm*
27 Delayed 24 Hour Waterflow
28 Instant 24 Hour Waterflow
29 Auto Verified Fire
30 Fire Supervisory
31 Day Zone*
87 Delay 24 Hour Fire (Wireless)**
88 Standard 24 Hour Fire (Wireless)**
*For burglary applications only
** For residential fire applications only
NOTE:To use 24-hour Buzzer zones, keypads must be installed .
NOTE:Keypad zones are assigned in section [020]. Zone Attributes are assigned in sections [101] - [132]. Zone assignment is
in sections [202] - [261].
Section #
Zone #
Default
Zone
Defn.
[001]
01
01
I_____I_____I
02
03
I_____I_____I
03
03
I_____I_____I
04
03
I_____I_____I
05
04
I_____I_____I
06
04
I_____I_____I
07
04
I_____I_____I
08
04
I_____I_____I
09
00
I_____I_____I
10
00
I_____I_____I
11
00
I_____I_____I
12
00
I_____I_____I
13
00
I_____I_____I
14
00
I_____I_____I
15
00
I_____I_____I
16
00
I_____I_____I
17
00
I_____I_____I
18
00
I_____I_____I
19
00
I_____I_____I
20
00
I_____I_____I
21
00
I_____I_____I
22
00
I_____I_____I
23
00
I_____I_____I
24
00
I_____I_____I
25
00
I_____I_____I
26
00
I_____I_____I
27
00
I_____I_____I
28
00
I_____I_____I
29
00
I_____I_____I
30
00
I_____I_____I
31
00
I_____I_____I
32
00
I_____I_____I
[002]
4
Basic Programming:
System Times and Codes
[005] System Times
NOTE: Valid entries for Entry Delay is between 001-255, valid entries for Exit Delay is between 001-255.
[01] Partition 1 Entry/Exit times
[05] Partition 5 Entry/Exit times
I___I___I___I
Entry Delay 1
I___I___I___I
Entry Delay 1
030
030
045
120
I___I___I___I
I___I___I___I
Entry Delay 1
Exit Delay
[02] Partition 2 Entry/Exit times
I___I___I___I
Entry Delay 1
030
045
120
I___I___I___I
I___I___I___I
Entry Delay 1
Exit Delay
[03] Partition 3 Entry/Exit times
I___I___I___I
Entry Delay 1
030
045
120
I___I___I___I
I___I___I___I
Entry Delay 1
Exit Delay
[04] Partition 4 Entry/Exit times
I___I___I___I
Entry Delay 1
030
045
I___I___I___I
Entry Delay 1
I___I___I___I
Exit Delay
120
[09] Bell Cut-Off Timer (All Partitions)
I___I___I___I
Enter 3 digits from 001-255
004
045
120
I___I___I___I
I___I___I___I
Entry Delay 1
Exit Delay
[06] Partition 6 Entry/Exit times
I___I___I___I
Entry Delay 1
030
045
120
I___I___I___I
I___I___I___I
Entry Delay 1
Exit Delay
[07] Partition 7 Entry/Exit times
I___I___I___I
Entry Delay 1
030
045
120
I___I___I___I
I___I___I___I
Entry Delay 1
Exit Delay
[08] Partition 8 Entry/Exit times
I___I___I___I
Entry Delay 1
030
045
120
I___I___I___I
I___I___I___I
Entry Delay 1
Exit Delay
[006] Installer’s Code
Default
I_______I_______I_______I_______I
5555
[007] Master Code
Default
1234
I_______I_______I_______I_______I
[008] Maintenance Code
Default
AAAA
I_______I_______I_______I_______I
Programmable Output Options
01
02
03
04
05
06
07
08
09
10
11
12
13
Residential Burglary and Fire Bell Output
For Future Use
Sensor Reset [*][7][2]
2 Wire Smoke Support (PGM 2 only)
System Armed Status
Ready To Arm
Keypad Buzzer Follow Mode
Courtesy Pulse
System Trouble Output (with Trouble options)
System Event [Strobe (with Event options)]
System Tamper (all sources: zones, keypad, modules)
TLM and Alarm
Kissoff Output
14
15
16
17
18
19
20
21
22
23
24
25
Ground Start Pulse
Remote Operation (DLS-3 Support)
LINKS1000 Support (PGM1 only)
Away Armed Status
Stay Armed Status
Command Output #1 ([*][7][1])
Command Output #2 ([*][7][2])
Command Output #3 ([*][7][3])
Command Output #4 ([*][7][4])
24 Hour Silent Input
24 Hour Audible Input
Delayed Fire and Burglary Output
NOTE: Output types [03] and [20] cannot be used together on the same system.
[009] PGM1 and PGM2 Output Programming (Main Panel)
NOTE: Program PGM Option Attributes in sections [501] - [514]. Program PGM partitions in sections [551] - [564]
Default
Default
19
I_______I_______I
PGM 1
10
I_______I_______I PGM 2
[010] PGM3 to PGM10 Output Programming (Main Panel/PC5208)
NOTE: Program PGM Option Attributes in sections [501] - [514]. Program PGM partitions in sections [551] - [564]
Default
Default
01
I_______I_______I
PGM 3 (main panel/PC5208)*
01
I_______I_______I
PGM 7 (PC5208)
01
I_______I_______I
PGM 4 (main panel/PC5208)*
01
I_______I_______I
PGM 8 (PC5208)
01
I_______I_______I
PGM 5 (PC5208)
01
I_______I_______I
PGM 9 (PC5208)
01
I_______I_______I
PGM 6 (PC5208)
01
I_______I_______I
PGM 10 (PC5208)
NOTE: These two sections allow you to program both PGM3 and PGM4 on the main panel, and the first two PGM outputs on
the PC5208. If you use both the main panel and the PC5208 outputs, PGM3 will work the same as the first PC5208 output,
and PGM4 will work the same as the second PC5208 output.
5
[011] PGM11 to PGM14 Output Programming (PC5204)
NOTE: Program PGM Option Attributes in sections [501] - [514]. Program PGM partitions in sections [551] - [564]
Default
01
I_______I_______I
PGM 11
Default
01
I_______I_______I
PGM 13
01
I_______I_______I
PGM 12
01
I_______I_______I
PGM 14
Other System Options
[012] Keypad Lockout Options
NOTE:If Keypad Lockout is active, the panel cannot be disarmed with a keyswitch.
Default
000
I_______I_______I_______I
Number of Invalid Codes Before Lockout (001-255 codes)
000
I_______I_______I_______I
Lockout Duration (001-255 minutes)
[013] First System Option Code
Default
Option
ON
1
Normally Closed Loops
OFF I________I
OFF
End-of-Line Resistors
OFF
I________I
2
Double End-of-Line Resistors
Single End-of-Line Resistors
ON*
I________I
3
Panel shows all troubles when armed
Panel shows only Fire troubles when armed
OFF
I________I
4
Tampers/Faults do not show as open
Tampers/Faults show as open
ON
I________I
2
Auto-Arm Schedule in [*][6]†
Auto-Arm Schedule in Installer Programming Only
ON
I________I
6
Audible Exit Fault Enabled
Audible Exit Fault Disabled
ON
I________I
7
Event Buffer Follows Swinger Shutdown Event Buffer Logs Events Past shutdown
OFF
I________I
8
Temporal Three Fire Signal Enabled
Standard Pulsed Fire Signal
* Option 3 must be OFF if LCD keypads older than v2.0 are used.
†This option applies to all partitions.
[014] Second System Option Code
Default
Option
ON
OFF I________I
1
Arm / Disarm Bell Squawk enabled
OFF
Arm / Disarm Bell Squawk disabled
OFF
I________I
2
Bell Squawk During Auto Arm
No Bell Squawk During Auto Arm
OFF
I________I
3
Bell Squawk On Exit Delay
No Bell Squawk On Exit Delay
OFF
I________I
4
Bell Squawk On Entry Delay
No Bell Squawk On Entry Delay
OFF
I________I
5
Bell Squawk On Trouble
No Bell Squawk On Trouble
ON
I________I
6
Audible Exit with Urgency
Silent Exit Delay
OFF
I________I
7
Exit Delay Termination Enabled
Exit Delay Termination Disabled
OFF
I________I
8
Residential Fire Bell is Continuous
Residential Fire Bell Follows Bell Cut-off
[015] Third System Option Code
Default
Option
ON
1
Fire Keys Enabled
ON I________I
OFF
Fire Keys Disabled
OFF
I________I
2
Panic Keys Audible (Bell / Beeps)
Panic Keys Silent
OFF
I________I
3
Quick Exit Enabled
Quick Exit Disabled
ON*
I________I
4
Quick Arming Enabled/
Function keys do not require code
Quick Arming Disabled/
Function keys require code
OFF**
I________I
5
Code Required For Bypassing
No Code Required
OFF
I________I
6
Master Code Not Changeable
Master Code Changeable
ON
I________I
7
TLM Enabled
TLM Disabled
OFF
I________I
8
TLM Audible (Bell) When Armed
TLM Trouble Beeps When Armed
* When using a PC5132 version 2.1 or older with the WLS909 Wireless Key, Option [4] must be ON for the Arm button to work.
**If option [5] is ON, function keys programmed as [08] Bypass will require an access code when used, even if option [4] is also on.
6
Basic Programming:
[016] Fourth System Option Code
Default
Option
ON
AC Trouble Displayed
ON I________I 1
OFF I________I 2
Trouble Light Flashes if AC Fails
Blank Keypad When Not Used
OFF I________I 3
Code Required to Remove Keypad Blanking
OFF I________I 4
ON I________I 5
Keypad Backlighting is enabled
Power Save Mode enabled
OFF I________I 6
Bypass Status Displayed While Armed
OFF I________I 7
OFF I________I 8
Keypad Tampers enabled
[017] Fifth System Option Code
Default
Option ON
I________I
1
WLS Key Does Not Use Access Codes*
ON
OFF
I________I
2
RF Jam Log After 5 Minutes
I________I
3
Audible RF Jam Trouble Beeps
OFF
OFF
I________I
4
Double Hit Enabled
I________I
5
Late to Close Enabled
OFF
I________I
6
Daylight Savings Time Enabled
OFF
ON
I________I
7
For Future Use
8
Squawk on Away Key Arming/Disarming Only
OFF I________I
OFF
AC Trouble Not Displayed
Trouble Light Does Not Follow AC Status
Keypad Active Always
No Code Required
Keypad Backlighting is disabled
Power Save Mode disabled
Bypass Status Not Displayed While Armed
Keypad Tampers disabled
OFF
WLS Key Uses Access Codes
RF Jam Log After 30 Seconds
Silent RF Trouble Jam Beeps
Double Hit Disabled
Late to Close Disabled
Daylight Savings Time Disabled
Periodic Camera Test Disabled
Bell Squawk on all Arming/Disarming‡
*This option must be enabled when using a PC5132 v2.1 or earlier. / ‡This option is supplemental to Section 14 Option 1
[018] Sixth System Option Code
Default
Option
ON
OFF
1
Test Transmission Exception Enabled
Test Transmission Exception Disabled
OFF I________I
OFF I________I
2
Verbal Chime Enabled
Verbal Chime Disabled
3
Verbal Alarm Enabled
Verbal Alarm Disabled
OFF I________I
4
Water-Flow Silence Inhibit Enabled
Water-Flow Silence Inhibit Disabled
OFF I________I
OFF I________I
5
Keypad Buzzer Follows Bell Enabled
Keypad Buzzer Follows Bell Disabled
6
Cross Zoning Enabled
Cross Zoning Disabled
OFF I________I
7
Exit Delay Restart Enabled
Exit Delay Restart Disabled
OFF I________I
OFF I________I
8
AC Trouble Beeps Enabled
AC Trouble Beeps Disabled
NOTE: For Cross Zoning to function, Option[6] in Section [018] and Option [9] in Section [101]-[132] must be ON for the desired
zone. Each zone has the ability to protect the intended area. Cross Zoning is not recommended for line security installations or on
exit/entry zone types.
Keypad Zone Assignments
[020] Keypad Zone Assignments
NOTE: Only one keypad may be assigned to a zone.
Default
00
00
00
00
00
00
00
00
I________I_______I
I________I_______I
I________I_______I
I________I_______I
I________I_______I
I________I_______I
I________I_______I
I________I_______I
Keypad (slot 1) Zone
Keypad (slot 2) Zone
Keypad (slot 3) Zone
Keypad (slot 4) Zone
Keypad (slot 5) Zone
Keypad (slot 6) Zone
Keypad (slot 7) Zone
Keypad (slot 8) Zone
Valid entries are zones 01-32
Valid entries are zones 01-32
Valid entries are zones 01-32
Valid entries are zones 01-32
Valid entries are zones 01-32
Valid entries are zones 01-32
Valid entries are zones 01-32
Valid entries are zones 01-32
Zone Loop Response Option Code
[030] Sixth System Option Code
Default
Option
ON
OFF I________I
1
Zone 1 is Fast Loop Response
OFF I________I
2
Zone 2 is Fast Loop Response
OFF I________I
3
Zone 3 is Fast Loop Response
4
Zone 4 is Fast Loop Response
OFF I________I
OFF I________I
5
Zone 5 is Fast Loop Response
OFF I________I
6
Zone 6 is Fast Loop Response
OFF I________I
7
Zone 7 is Fast Loop Response
8
Zone 8 is Fast Loop Response
OFF I________I
OFF
Zone 1 is Normal Loop Response
Zone 2 is Normal Loop Response
Zone 3 is Normal Loop Response
Zone 4 is Normal Loop Response
Zone 5 is Normal Loop Response
Zone 6 is Normal Loop Response
Zone 7 is Normal Loop Response
Zone 8 is Normal Loop Response
7
Section 4: Advanced System
Programming
Zone Attributes
Zone Attribute Defaults (Y = Option ON; N = Option OFF):
Attribute:
ON
OFF
Zone Type:
00 Null Zone
01 Delay 1
02 Delay 2
03 Instant
04 Interior
05 Int. Stay/Away
06 Dly. Stay/Away
07 Dly. 24hr Fire (Hardw.)
08 Stand. 24hr Fire (Hardw.)
09 24hr Superv.
10 24hr Superv. Buzzer
11 24hr Burglary
12 24hr Holdup
13 24hr Gas
14 24hr Heating
15 24hr Medical
16 24hr Panic
17 24hr Emergency
18 24hr Sprinkler
19 24hr Water
20 24hr Freeze
21 24hr Latching Tamper
22 Momentary Keyswitch
23 Maintained Keyswitch
24 LINKS Answer
25 Interior Delay
26 24hr Non-alarm
27 Delayed 24hr Waterflow
28 Instant 24hr Waterflow
29 Auto Verified Fire
30 Fire Supervisory
31 Day Zone
87 Dly. 24hr Fire (Wireless)
88 Stand. 24hr Fire (Wireless)
Section
Zone #
Zone
Type**
1
2
3
4
5
6
7
8
9
Audible
Silent
Steady
Pulsed
Chime
No
Bypass
No
Force
No
Swing
No
Tx. Delay
No
Wireless Zn
No
Cross Zn
No
N
Y
Y
Y
Y
Y
Y
Y
Y
N
N
Y
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
N
N
N
Y
N
Y
Y
Y
N
Y
Y
Y
N
Y
Y
Y
Y
Y
Y
N
N
Y
Y
Y
Y
N
N
Y
Y
Y
Y
Y
Y
Y
N
N
N
Y
N
N
N
N
N
Y
N
N
N
Y
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Y
Y
Y
Y
Y
Y
N
N
N
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
Y
N
N
N
N
N
Y
N
N
N
N
N
N
N
Y
Y
N
N
Y
N
N
N
N
N
N
N
N
N
N
N
N
Y
Y
Y
N
Y
N
N
N
N
Y
N
N
N
Y
Y
Y
Y
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Y
N
N
N
N
N
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Audible/
Silent
1
Steady/
Pulsed
2
Chime
No
3
Bypass
No
4
Force
No
5
Swing
No
6
Tx. Delay
No
7
Wireless
No
8
Cross Zn
No
9
[101]
01
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________|
[102]
02
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[103]
03
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[104]
04
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[105]
05
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[106]
06
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[107]
07
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[108]
08
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[109]
09
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[110]
10
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[111]
11
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[112]
12
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[113]
13
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[114]
14
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
8
Advanced System Programming:
Section
Zone #
Zone
Type**
Audible/
Silent
1
Steady/
Pulsed
2
Chime
No
3
Bypass
No
4
Force
No
5
Swing
No
6
Tx. Delay
No
7
Wireless
No
8
Cross Zn
No
9
[115]
15
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[116]
16
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[117]
17
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[118]
18
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[119]
19
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[120]
20
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[121]
21
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[122]
22
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[123]
23
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[124]
24
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[125]
25
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[126]
26
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[127]
27
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[128]
28
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[129]
29
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[130]
30
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[131]
31
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
[132]
32
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
**Record here based on programming in sections [001] - [004]
System Timers
[165] Maximum Dialing Attempts to Each Telephone Number
Default: 007 I_______I_______I_______I
Valid entries are 001-015 attempts (do not enter 000).
[166] Post Dial Wait for Handshake (All Formats)
Valid entries are 001-255 seconds
Default: 040 I_______I_______I_______I
[167] T-Link Communications Wait for Acknowledge Delay
Valid entries are 001-255 seconds
Default: 020 I_______I_______I_______I
[170] PGM Output Timer
I_______I_______I_______I
Default: 005
Valid entries are 001-255 seconds
[175] Auto-Arm Postpone Timer
Valid entries are 001-255 minutes, 000 allows automatic arming to be cancelled
Default: 000 I_______I_______I_______I
[176] Cross Zone/Police Code Timer
Valid entries are 001-255 seconds/minutes
Default: 060 I_______I_______I_______I
[177] Waterflow Delay Timer
Valid entries are 000-090 seconds
Default: 000 I_______I_______I_______I
[178] Alarm Tone Verified for Verbal Alarm
Valid entries are 001-255 seconds
Default: 015 I_______I_______I_______I
9
Automatic Arming Schedule
Enter a four-digit number (HH:MM) for each day that the system will auto-arm. All entries are disabled (9999) by default. Valid
entries are 0000-2359.
Section # Partition
[181]
[182]
[183]
[184]
Day of the
Week
Time of Day
1
2
3
4
Section # Partition
[185]
Time of Day
Sunday
I_______I_______I:I_______I_______I
Sunday
I_______I_______I:I_______I_______I
Monday
I_______I_______I:I_______I_______I
Monday
I_______I_______I:I_______I_______I
Tuesday
I_______I_______I:I_______I_______I
Tuesday
I_______I_______I:I_______I_______I
Wednesday
I_______I_______I:I_______I_______I
Wednesday
I_______I_______I:I_______I_______I
Thursday
I_______I_______I:I_______I_______I
Thursday
I_______I_______I:I_______I_______I
Friday
I_______I_______I:I_______I_______I
Friday
I_______I_______I:I_______I_______I
Saturday
I_______I_______I:I_______I_______I
Saturday
I_______I_______I:I_______I_______I
[186]
5
Day of the
Week
Sunday
I_______I_______I:I_______I_______I
Sunday
I_______I_______I:I_______I_______I
Monday
I_______I_______I:I_______I_______I
Monday
I_______I_______I:I_______I_______I
Tuesday
I_______I_______I:I_______I_______I
Tuesday
I_______I_______I:I_______I_______I
Wednesday
I_______I_______I:I_______I_______I
Wednesday
I_______I_______I:I_______I_______I
Thursday
I_______I_______I:I_______I_______I
Thursday
I_______I_______I:I_______I_______I
Friday
I_______I_______I:I_______I_______I
Friday
I_______I_______I:I_______I_______I
Saturday
I_______I_______I:I_______I_______I
Saturday
I_______I_______I:I_______I_______I
[187]
6
Sunday
I_______I_______I:I_______I_______I
Sunday
I_______I_______I:I_______I_______I
Monday
I_______I_______I:I_______I_______I
Monday
I_______I_______I:I_______I_______I
Tuesday
I_______I_______I:I_______I_______I
Tuesday
I_______I_______I:I_______I_______I
Wednesday
I_______I_______I:I_______I_______I
Wednesday
I_______I_______I:I_______I_______I
Thursday
I_______I_______I:I_______I_______I
Thursday
I_______I_______I:I_______I_______I
Friday
I_______I_______I:I_______I_______I
Friday
I_______I_______I:I_______I_______I
Saturday
I_______I_______I:I_______I_______I
Saturday
I_______I_______I:I_______I_______I
[188]
7
Sunday
I_______I_______I:I_______I_______I
Sunday
I_______I_______I:I_______I_______I
Monday
I_______I_______I:I_______I_______I
8
Monday
I_______I_______I:I_______I_______I
Tuesday
I_______I_______I:I_______I_______I
Tuesday
I_______I_______I:I_______I_______I
Wednesday
I_______I_______I:I_______I_______I
Wednesday
I_______I_______I:I_______I_______I
Thursday
I_______I_______I:I_______I_______I
Thursday
I_______I_______I:I_______I_______I
Friday
I_______I_______I:I_______I_______I
Friday
I_______I_______I:I_______I_______I
Saturday
I_______I_______I:I_______I_______I
Saturday
I_______I_______I:I_______I_______I
[190] No Activity Arming Pre-Alert Time
Default
Partition
Default
001
All
No Activity Arming Timers
Section
Partition
[191]
[192]
[193]
[194]
[195]
[196]
[197]
[198]
I_______I_______I_______I
Valid entries are 001-255 seconds, 000 for no pre-alert
Default
1
I_______I_______I_______I
Valid entries are 001-255 seconds, 000 to disable
2
I_______I_______I_______I
Valid entries are 001-255 seconds, 000 to disable
3
I_______I_______I_______I
Valid entries are 001-255 seconds, 000 to disable
4
I_______I_______I_______I
Valid entries are 001-255 seconds, 000 to disable
5
I_______I_______I_______I
Valid entries are 001-255 seconds, 000 to disable
6
I_______I_______I_______I
Valid entries are 001-255 seconds, 000 to disable
7
I_______I_______I_______I
Valid entries are 001-255 seconds, 000 to disable
8
I_______I_______I_______I
Valid entries are 001-255 seconds, 000 to disable
NOTE: Default is [000] for all partitions.
[199] Auto-Arming Pre-Alert Timer
Valid entries are 001-255 seconds
Default: 005 I_______I_______I_______I
10
Section 5: Partition and Zone
Programming
[201] Partition Selection Mask
Select which partitions will be active on the system
NOTE: Partition 1 cannot be disabled.
Default
Option
ON
ON I________I
1
Partition 1 is enabled
OFF
(cannot be turned off)
OFF
I________I
2
Partition 2 is enabled
Disabled
OFF
I________I
3
Partition 3 is enabled
Disabled
OFF
I________I
4
Partition 4 is enabled
Disabled
OFF
I________I
5
Partition 5 is enabled
Disabled
OFF
I________I
6
Partition 6 is enabled
Disabled
OFF
I________I
7
Partition 7 is enabled
Disabled
OFF
I________I
8
Partition 8 is enabled
Disabled
Assigning Zones to Partitions
Program which zones will be assigned to each partition in sections [202] to [261]. Program zone definitions in sections [001] [002] and zone attributes in sections [101] - [132]. Program keypad zone assignments in section [020].
NOTE: By default, zones 1 through 8 are assigned to partition 1. All other zones are not assigned to a partition.
ON = Assigned to partition; OFF = Not assigned to partition
Section
[202]
[203]
[204]
[205]
Section
[210]
[211]
[212]
[213]
Partition
1
1
1
1
Partition
2
2
2
2
Zone:
01
02
03
04
05
06
07
08
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
09
10
11
12
13
14
15
16
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
17
18
19
20
21
22
23
24
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
25
26
27
28
29
30
31
32
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
Zone:
01
02
03
04
05
06
07
08
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
09
10
11
12
13
14
15
16
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
17
18
19
20
21
22
23
24
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
25
26
27
28
29
30
31
32
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
11
Assigning Zones to Partitions
Section
[218]
Partition
Section
3
Zone:
Partition
01
I________I
[219]
[220]
[221]
Section
[226]
[227]
[228]
[229]
Section
[234]
[235]
[236]
[237]
3
3
3
Partition
4
4
4
4
Partition
5
5
5
5
02
I________I
Zone:
03
I________I
04
05
06
07
08
I________I
I________I
I________I
I________I
I________I
09
10
11
12
13
14
15
16
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
17
18
19
20
21
22
23
24
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
25
26
27
28
29
30
31
32
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
Zone:
01
02
03
04
05
06
07
08
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
09
10
11
12
13
14
15
16
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
17
18
19
20
21
22
23
24
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
25
26
27
28
29
30
31
32
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
Zone:
01
02
03
04
05
06
07
08
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
09
10
11
12
13
14
15
16
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
17
18
19
20
21
22
23
24
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
25
26
27
28
29
30
31
32
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
Assigning Zones to Partitions
Section
[242]
[243]
[244]
[245]
Section
[250]
[251]
[252]
[253]
Section
[258]
[259]
[260]
[261]
12
Partition
6
6
6
6
Partition
7
7
7
7
Partition
8
8
8
8
Zone:
01
02
03
04
05
06
07
08
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
09
10
11
12
13
14
15
16
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
17
18
19
20
21
22
23
24
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
25
26
27
28
29
30
31
32
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
Zone:
01
02
03
04
05
06
07
08
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
09
10
11
12
13
14
15
16
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
17
18
19
20
21
22
23
24
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
25
26
27
28
29
30
31
32
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
Zone:
01
02
03
04
05
06
07
08
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
09
10
11
12
13
14
15
16
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
17
18
19
20
21
22
23
24
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
25
26
27
28
29
30
31
32
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
Section 6: Communicator
Programming
Telephone Numbers
NOTE: For sections [301] to [353], the content of every section by default is [F].
[301] First Telephone Number (32 Digits)
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[302] Second Telephone Number (32 Digits)
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[303] Third Telephone Number (32 Digits)
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[304] Call Waiting Cancel String (6 Digits)
I_______I_______I_______I_______I_______I_______I Default = DB70EF Program unused digits with Hex F
NOTE: All six digits must be entered for changes to be saved. Fill unused digit spaces with ‘F’
NOTE: When using T-Link, program CAAA as the phone number.
Account Codes
Enter a six-digit account number for the system account code. SIA will use this account code for all eight partitions. Only SIA supports six digit account codes. If the last two digits of the account code are FF, the panel will only use the first four digits.
Section
[310]
System Account Code
I_______I_______I_______I_______I_______I_______I
Enter a four-digit account number for each active partition.
Section
Partition
Partition Account Code
[311]
1
I_______I_______I_______I_______I
[312]
2
I_______I_______I_______I_______I
[313]
3
I_______I_______I_______I_______I
[314]
4
I_______I_______I_______I_______I
[315]
5
I_______I_______I_______I_______I
[316]
6
I_______I_______I_______I_______I
[317]
7
I_______I_______I_______I_______I
[318]
8
I_______I_______I_______I_______I
Reporting Codes
Alarm Reporting Codes, Zones 01-32
Note: All reporting codes are defaulted to FF.
Section
[320]
Zone 01
Zone 02
Zone 03
[321]
Zone 04
Zone 05
Zone 06
Zone 07
Zone 08
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 09
Zone 10
Zone 11
Zone 12
Zone 13
Zone 14
Zone 15
Zone 16
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 17
Zone 18
Zone 19
Zone 20
Zone 21
Zone 22
Zone 23
Zone 24
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 25
Zone 26
Zone 27
Zone 28
Zone 29
Zone 30
Zone 31
Zone 32
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Alarm Restoral Reporting Codes, Zones 01-32
Section
[324]
Zone 01
Zone 02
Zone 03
[325]
Zone 04
Zone 05
Zone 06
Zone 07
Zone 08
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 09
Zone 10
Zone 11
Zone 12
Zone 13
Zone 14
Zone 15
Zone 16
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 24
Zone 17
Zone 18
Zone 19
Zone 20
Zone 21
Zone 22
Zone 23
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 25
Zone 26
Zone 27
Zone 28
Zone 29
Zone 30
Zone 31
Zone 32
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
13
[328] Miscellaneous Alarm Reporting Codes
I_______I_______I Duress Alarm
I_______I_______I Opening After Alarm
I_______I_______I Recent Closing
I_______I_______I Zone Expander Supervisory Alarm
I_______I_______I Zone Expander Supervisory Restore
I_______I_______I Cross Zone Police Code Alarm
I_______I_______I Burglary Not Verified
I_______I_______I Alarm Cancelled
[329] Priority Alarm and Restoral
I_______I_______I Keypad Fire Alarm
I_______I_______I
Keypad Auxiliary Alarm
I_______I_______I
Keypad Panic Alarm
I_______I_______I
Auxiliary Input Alarm
I_______I_______I
Keypad Fire Restoral
I_______I_______I
Keypad Auxiliary Restoral
I_______I_______I
Keypad Panic Restoral
I_______I_______I
Auxiliary Input Restore
Tamper Reporting Codes, Zones 01-32
Section
[330]
Zone 01
Zone 02
Zone 03
I_______I_______I
[331]
I_______I_______I
I_______I_______I
Zone 05
Zone 06
Zone 07
Zone 08
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 09
Zone 10
Zone 11
Zone 12
Zone 13
Zone 14
Zone 15
Zone 16
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 17
Zone 18
Zone 19
Zone 20
Zone 21
Zone 22
Zone 23
Zone 24
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 25
Zone 26
Zone 27
Zone 28
Zone 29
Zone 30
Zone 31
Zone 32
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Tamper Restoral Reporting Codes, Zones 01-32
Section
[334]
Zone 01
Zone 02
Zone 03
I_______I_______I
[335]
Zone 04
I_______I_______I
I_______I_______I
I_______I_______I
Zone 04
Zone 05
Zone 06
Zone 07
Zone 08
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 09
Zone 10
Zone 11
Zone 12
Zone 13
Zone 14
Zone 15
Zone 16
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 17
Zone 18
Zone 19
Zone 20
Zone 21
Zone 22
Zone 23
Zone 24
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Zone 25
Zone 26
Zone 27
Zone 28
Zone 29
Zone 30
Zone 31
Zone 32
[338] Miscellaneous Tamper Reporting Codes
I_______I_______I General System Tamper
I_______I_______I
General System Tamper Rest.
I_______I_______I
Keypad Lockout
Closing (Arming) Reporting Codes, Access Codes 1-32
Section
[339]
Code 1
Code 2
Code 3
Code 4
[340]
14
Code 5
Code 6
Code 7
Code 8
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Code 9
Code 10
Code 11
Code 12
Code 13
Code 14
Code 15
Code 16
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Code 17
Code 18
Code 19
Code 20
Code 21
Code 22
Code 23
Code 24
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Code 25
Code 26
Code 27
Code 28
Code 29
Code 30
Code 31
Code 32
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Communicator Programming:
[341] Miscellaneous Closing (Arming) Reporting Codes
I_______I_______I Closing by Duress Code 33
I_______I_______I
Closing by Duress Code 34
I_______I_______I
Closing by Master Code 40
I_______I_______I
Closing by Supervisory Code 41
I_______I_______I
Closing by Supervisory Code 42
I_______I_______I
Partial Closing
I_______I_______I
Special Closing
I_______I_______I
Late to Close
Opening (Disarming) Reporting Codes, Access Codes 1-32
Section
[342]
Code 1
Code 2
Code 3
Code 4
[343]
Code 5
Code 6
Code 7
Code 8
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Code 9
Code 10
Code 11
Code 12
Code 13
Code 14
Code 15
Code 16
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Code 17
Code 18
Code 19
Code 20
Code 21
Code 22
Code 23
Code 24
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
Code 25
Code 26
Code 27
Code 28
Code 29
Code 30
Code 31
Code 32
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
I_______I_______I
[344] Miscellaneous Opening (Disarming) Reporting Codes
I_______I_______I
Opening by Duress Code 33
I_______I_______I
Opening by Duress Code 34
I_______I_______I
Opening by Master Code 40
I_______I_______I
Opening by Supervisory Code 41
I_______I_______I
Opening by Supervisory Code 42
I_______I_______I
Auto Arm Cancellation
I_______I_______I
Special Opening
[345] Maintenance Alarm Reporting Codes
I_______I_______I Battery Trouble Alarm
I_______I_______I
AC Failure Trouble Alarm
I_______I_______I
Bell Circuit Trouble Alarm
I_______I_______I
Fire Trouble Alarm
I_______I_______I
Auxiliary Power Supply Trouble Alarm
I_______I_______I
TLM Trouble Code (via LINKS)
I_______I_______I
General System Trouble
I_______I_______I
General System Supervisory
[346] Maintenance Restoral Reporting Codes
I_______I_______I Battery Trouble Restoral
I_______I_______I
AC Failure Trouble Restoral
I_______I_______I
Bell Circuit Trouble Restoral
I_______I_______I
Fire Trouble Restoral
I_______I_______I
Auxiliary Power Supply Trouble Restoral
I_______I_______I
TLM Restoral
I_______I_______I
General System Trouble Restore
I_______I_______I
General System Supervisory Restore
15
[347] Miscellaneous Maintenance Reporting Codes
I_______I_______I Telephone Number 1 FTC Restore
I_______I_______I
Telephone Number 2 FTC Restore
I_______I_______I
Event Buffer 75% Full Since Last Upload
I_______I_______I
DLS Lead IN
I_______I_______I
DLS Lead OUT
I_______I_______I
Zone Fault Alarm
I_______I_______I
Zone Fault Restore
I_______I_______I
Delinquency Code
I_______I_______I
General Zone Low Battery Alarm
I_______I_______I
General Zone Low Battery Restoral
[348] Test Transmission Reporting Codes
I_______I_______I Walk Test End
I_______I_______I
Walk Begin
I_______I_______I
Periodic Test Transmission with Trouble
I_______I_______I
Periodic Test Transmission
I_______I_______I
System Test
I_______I_______I
LINKS1000 Test Transmission Code*
*The LINKS1000 Test Transmission Code must be programmed as “00” for the LINKS1000 Test Transmission to be disabled.
[350] Communicator Format Options
NOTE:The Third telephone number follows the format of the First telephone number.
Default
04 I_______I_______I
04
I_______I_______I
1st/3rd Telephone Number
2nd Telephone Number
01 20 BPS, 1400 HZ handshake
02 20 BPS, 2300 HZ handshake
03 DTMF CONTACT ID
04 SIA FSK
05 Pager
06 Residential Dial
07 10 BPS, 1400Hz handshake
08 10 BPS, 2300Hz handshake
Call Direction Options
Alarm/Restore Communicator Call Directions
Section Partition Option:
Defaults:
[351]
[352]
[353]
[354]
[355]
[356]
[357]
[358]
1
2
3
4
5
6
7
8
5
4
Alternate
2nd Telephone
Communicator
Number (via
LINKS1000)
2
2nd Telephone
Number
3
1st Telephone
Number (via
LINKS1000)
ON
OFF
OFF
OFF
ON
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
NOTE:The LINKS1000 backup call directions will only back up their respective telephone numbers.
16
6,7,8
For
Future
Use
1
1st Telephone
Number
Communicator Programming:
Tamper/Restore Communicator Call Directions
Section Partition Option:
Defaults:
[359]
[360]
[361]
[362]
[363]
[364]
[365]
[366]
1
2
3
4
5
6
7
8
5
4
Alternate
2nd Telephone
Communicator
Number (via
LINKS1000)
6,7,8
For
Future
Use
1
1st Telephone
Number
2
2nd Telephone
Number
3
1st Telephone
Number (via
LINKS1000)
ON
OFF
OFF
OFF
ON
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
NOTE:The LINKS1000 backup call directions will only back up their respective telephone numbers.
Opening/Closing Communicator Call Directions
Section Partition Option:
Defaults:
[367]
[368]
[369]
[370]
[371]
[372]
[373]
[374]
1
2
3
4
5
6
7
8
5
4
Alternate
2nd Telephone
Communicator
Number (via
LINKS1000)
6,7,8
For
Future
Use
1
1st Telephone
Number
2
2nd Telephone
Number
3
1st Telephone
Number (via
LINKS1000)
ON
OFF
OFF
OFF
ON
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
I________I
NOTE: The LINKS1000 backup call directions will only back up their respective telephone numbers.
System Maintenance Communicator Call Directions
Section
Option:
Defaults:
[375]
5
4
Alternate
2nd Telephone
Communicator
Number (via
LINKS1000)
6,7,8
For
Future
Use
1
1st Telephone
Number
2
2nd Telephone
Number
3
1st Telephone
Number (via
LINKS1000)
ON
OFF
OFF
OFF
ON
I________I
I________I
I________I
I________I
I________I
I________I
I________I
NOTE:The LINKS1000 backup call directions will only back up their respective telephone numbers.
System Test Transmissions Communicator Call Directions
Section
Option:
Defaults:
[376]
1
1st Telephone
Number
2
2nd Telephone
Number
3
1st Telephone
Number (via
LINKS1000)
5
4
Alternate
2nd Telephone
Communicator
Number (via
LINKS1000)
6,7,8
For
Future
Use
ON
OFF
OFF
OFF
ON
I________I
I________I
I________I
I________I
I________I
I________I
I________I
NOTE:The LINKS1000 backup call directions will follow the programming in Sections 351-376, above.
17
[377] Communication Variables
Default
003
I_______I_______I_______I
Swinger Shutdown (Alarms and Rest)
(001-014 Transmissions)
003
I_______I_______I_______I
Swinger Shutdown (Tampers and Rest)
(001-014 Transmissions, 000=disabled)
003
I_______I_______I_______I
Swinger Shutdown (Maint and Rest)
(001-014 Transmissions, 000=disabled)
000
I_______I_______I_______I
Communication Delay
(001-255 seconds)
030
I_______I_______I_______I
AC Failure Communication Delay
(001-255 minutes)
003
I_______I_______I_______I
TLM Trouble Delay
(No. of checks required - valid entries 003 - 255)
030
I_______I_______I_______I
Test Transmission Cycle (land line)
(001-255 days/minutes)†
030
I_______I_______I_______I
Test Transmission Cycle (LINKS1000)
(001-255 days)
007
I_______I_______I_______I
Zone Low Battery Transmission Delay
(000-255 days)
030
I_______I_______I_______I
Delinquency Transmission Cycle
(000-255 days/hours)
000
I_______I_______I_______I
Communications Cancelled Window
(000-255 minutes)
†Depends on programming in section [702], option [3].
NOTE: To disable the AC failure communications delay, program [000].
NOTE: Transmission delay cannot be used in conjunction with Downlook.
[378] Test Transmission Time of Day
Default
9999
I_______I_______I_______I_______I
Valid entries are 0000-2359, 9999 to disable)
Communicator Options
[380] First Communicator Option Code
Default
Option
ON
ON I_______I
1
Communications Enabled
OFF
Communications Disabled
OFF
I_______I
2
Restorals on Bell Time-out
Restorals Follow Zones
OFF
I_______I
3
Pulse Dialing
DTMF Dialing
OFF
I_______I
4
Switch to Pulse Dialing on 5th Attempt
DTMF Dial For All Attempts
OFF
I_______I
5
3rd Telephone Number enabled
3rd Telephone Number disabled
OFF
I_______I
6
Alternate Dial (1st and 3rd)
Call 1st Number, Backup to 3rd
OFF
I_______I
7
Call LINKS as well as land line
LINKS is Backup of land line(s)
OFF
I_______I
8
Delinquency Follows Zone Activity (Hours)
Delinquency Follows Arming (Days)
[381] Second Communicator Option Code
Default
Option ON
OFF I_______I
1
Open After Alarm Kypd Ringback enabled
OFF
Open After Alrm Kypd Ringback disabled
OFF
I_______I
2
Open After Alarm Bell Ringback enabled
Open After Alrm Bell Ringback disabled
OFF
I_______I
3
SIA Sends Programmed Rep. Codes
SIA Sends Automatic Rep. Codes
OFF
I_______I
4
Closing Confirmation Enabled
Closing Confirmation Disabled
ON
I_______I
5
Talk/Listen (PC5936) on phone lines 1/3
No Talk/Listen (PC5936) on phone lines 1/3
OFF
I_______I
6
Talk/Listen (PC5936) on phone line 2
No Talk/Listen (PC5936) on phone line 2
ON
OFF
I_______I
7
8
Contact ID Uses Programmed Rep. Codes
For Future Use
Contact ID Uses Automatic Rep. Codes
I_______I
[382] Third Communicator Option Code
Default
Option ON
OFF I_______I
1
Contact ID. Partial Closing Identifier is 5
OFF
Partial Closing ID is 4
OFF
I_______I
2
Alarm Communications Enabled During Walk Test
Alarm Communications Disabled During Walk Test
ON
I_______I
3
Communication Cancelled Message Enabled
Communication Cancelled Message Disabled
OFF
I_______I
4
Call Waiting Cancel Enabled*
Call Waiting Cancel Disabled
OFF
I_______I
5
T-Link Interface Enabled
T-Link Interface Disabled
OFF
I_______I
6
AC Failure Transmission Delay is in Hours
AC Failure Transmission Delay is in Minutes
OFF
I_______I
7-8
For Future Use
* A Call Waiting Cancel on a non-Call Waiting line will prevent successful connection to the central station.
18
Communicator Programming:
LINKS1000 Preambles
[390] LINKS1000 Preamble (First Telephone Number)
I_______I_______I_______I_______I
(Program all unused digits with Hex F)
Default: FFFF
[391] LINKS1000 Preamble (Second Telephone Number)
Default: FFFF
I_______I_______I_______I_______I
(Program all unused digits with Hex F)
[392] LINKS1000 Preamble (Third Telephone Number)
Default: FFFF
I_______I_______I_______I_______I
(Program all unused digits with Hex F)
[393] LINKS1000 Special Function Preamble (All Telephone Numbers)
Default: FFFFFF I_______I_______I_______I_______I_______I_______I (Program all unused digits with Hex F)
• Enter [*][2][*] (HEX B) to dial [*]
• Enter [*][3][*] (HEX C) to dial [#]
19
Section 7: Downloading Options
[401] First Downloading Option Code
Default
Option
ON
OFF
OFF
I_______I
1
Answering machine/double call enabled
Answering machine/double call disabled
ON
I_______I
2
User Can Enable DLS Window
User Cannot Enable DLS Window
OFF
I_______I
3
Call-Back Enabled
Call-Back Disabled
OFF
I_______I
4
User-initiated call-up enabled
User-initiated call-up disabled
OFF
I_______I
5
Auto Event Buffer Upload Enabled
Auto Event Buffer Upload Disabled
OFF
I_______I
6-8
For Future Use
[402] Downloading Computer’s Telephone Number (32 Digits)
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[403] Downloading Access Code
Default: 5005 I_______I_______I_______I_______IEnter 4 HEX digits
[404] Panel Identification Code
Default: 5005 I_______I_______I_______I_______IEnter 4 HEX digits
[405] Answering Machine Double-call Timer
Default: 060 I_______I_______I_______I (Valid entries are 001-255 seconds)
[406] Number of Rings to Answer On
Default: 000 I_______I_______I_______I (Valid entries are 000-255 rings)
[490] LINKS Preamble (Downloading Telephone Number)
Default: FFFFI_______I_______I_______I_______I (Program all unused digits with Hex F)
[499] Initiate PC-Link (Local Downloading)
To begin PC-Link downloading, enter [499][Installer’s Code][499].
20
Section 8: Programmable Output
Programming
Programmable Output Attributes
Program only the following attributes for the PGM options listed. All others will be ignored. PGM options are programmed in [009],
[010] & [011].
PGM Attribute Defaults (Y = Attribute ON; N = Attribute OFF):
Attribute:
ON
OFF
1
2
3
4
5
6
7
8
Not used
Not used
True Output
—
—
Inverted
Follows Timer
Code Req.
Not used
Not used
Not used
On / Off
No Code Req.
—
—
—
PGM Option
[01] Burg. / Fire Bell
Y
[02] Future Use
[03] Sensor Reset
Y
[04] 2-Wire Smoke Support (PGM2 only)
Y
[05] Armed Status
Y
[06] Ready To Arm
Y
[07] Kypd Bzz Follow
Y
[08] Courtesy Pulse
Y
N
[09] System Trouble Output / Trouble Options)
Y
Y
Y
Y
Y
Y
Y
Y
[10] System Event / Event Options)
Y
Y
Y
Y
Y
Y
Y
Y
[11] System Tamper
Y
[12] TLM and Alarm
Y
[13] Kiss-off
Y
[14] Gnd Strt Pulse
Y
[15] Remote Op.
Y
[16] LINKS1000 Sup.
Y
[17] Away Armed Status
Y
[18] Stay Armed Status
Y
[19] Comm. Output #1, [*][7][1]
Y
Y
Y
[20] Comm. Output #2, [*][7][2]
Y
Y
N
[21] Comm. Output #3, [*][7][3]
Y
Y
N
[22] Comm. Output #4, [*][7][4]
Y
Y
N
[23] Silent 24 Hr (PGM2 only)
Y
[24] Audible 24 Hr (PGM2 only)
Y
[25] Delayed Burglary & Fire Bell
Y
1
Attribute:
2
3
4
5
6
7
8
PGM Option
ON
Serv. req.
AC Fail
TLM Fault
FTC
Zone Fault
Zone Tmp.
Zn. Low Bat.
Loss of Clock
OFF
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Y
Y
Y
Y
Y
Y
Y
Y
ON
Burg. Evnt.
Fire Evnt.
Panic Evnt.
Med. Evnt.
Supv. Evnt.
Priority Evnt.
Holdup Evnt.
Follows Timer*
OFF
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Latched
Y
Y
Y
Y
Y
Y
Y
N
[09] System Trouble
[10] System Event
*If attribute [8] is turned ON, attributes [1-7] must also be turned ON.
Section PGM Output
1
2
3
4
5
6
7
8
#
Type*
Main Board
[501]
1
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
[502]
2
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
Main Board / PC5208
[503] ** 3
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
[504] ** 4
(
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
*Record here based on programming in [009], [010] and [011].
** These two sections allow you to program both PGM3 and PGM4 on the main panel, and the first two PGM outputs on the
PC5208. If you use both the main panel and the PC5208 outputs, PGM3 will work the same as the first PC5208 output, and PGM4
will work the same as the second PC5208 output.
21
Section PGM
#
PC5208
[505]
5
Output
Type*
1
2
3
(
[506]
6
(
[507]
7
[508]
8
[509]
[510]
4
)
I________I
I________|
I________|
I________|
)
I________I
I________|
I________|
I________|
(
)
I________I
I________|
I________|
(
)
I________I
I________|
I________|
9
(
)
I________I
I________|
10
(
)
I________I
[511]
11
(
)
[512]
12
(
)
[513]
13
(
[514]
14
(
5
6
7
8
I________|
I________|
I________|
I________I
I________|
I________|
I________|
I________I
I________|
I________|
I________|
I________|
I________I
I________|
I________|
I________|
I________|
I________I
I________|
I________|
I________|
I________|
I________|
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
)
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
PC5204
*Record here based on programming in [009], [010] and [011].
PGM Output Partition Assignment
Section PGM
#
Main Board
[551]
1
[552]
Partition: 1
2
2
3
4
5
6
7
8
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
Main Board / PC5208
[553]
3
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
[554]
4
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
[555]
5
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
[556]
6
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
[557]
7
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
[558]
8
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
[559]
9
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
[560]
10
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
[561]
11
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
[562]
12
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
[563]
13
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
[564]
14
I________I
I________|
I________|
I________|
I________|
I________|
I________|
I________I
PC5208
PC5204
22
Section 9: Inter national Programming
[700] Clock Adjust
Default: 60
I_______I______I
Valid entries are 01-99 seconds
[701] First International Options Code
Default
Option
ON
OFF I_______I
1
50 Hz AC
OFF
I_______I
2
OFF
I_______I
OFF
I_______I
OFF
60 Hz AC
Time Base - Internal Crystal
Time Base - AC Line
3
AC/DC Arming Inhibit Enabled
AC/DC Arming inhibit disabled
4
All System Tampers Require Installer Reset All System Tampers follow Restore
OFF
I_______I
5
6 digit User Access Codes
4 digit User Access Codes
OFF
I_______I
6
Busy Tone detection enabled
Busy Tone detection disabled
OFF
I_______I
7
High Current Battery Charge
Standard current battery charge
OFF
I_______I
8
For Future Use
[702] Second International Options Code
Default
Option ON
OFF I_______I
1
Pulse Dialing Make/Break Ratio is 33/67
OFF
Pulse Dialing Make/Break Ratio is 40/60
ON
I_______I
2
Force Dialing Enabled
OFF
I_______I
3
Land Line Test Transmission in Minutes
Land Line Test Transmission in Days
OFF
I_______I
4
1600 Hz Handshake
Standard Handshake
OFF
I_______I
5
ID Tone Enabled
ID Tone Disabled
OFF
I_______I
6
2100 Hz ID Tone
1300 Hz ID Tone
OFF
OFF
I_______I
7
8
One Time 1-Hr User Enabled DLS Window Full 6-Hr User Enabled DLS Window
Bell on FTC when Armed
FTC Trouble only when Armed
I_______I
Force Dialing Disabled
[703] Delay Between Dialing Attempts
Default:003 I_______I_______I_______I
Valid entries are 000-255 Seconds
23
Section 10: Module Programming
[801] PC5400 Printer Module Programming
Please refer to your PC5400 Installation Manual for installation and programming instructions.
[802] PC5936 Audio Interface Programming
Please refer to your PC5936 Installation Manual for installation and programming instructions.
[803] Alternate Communicator Programming
Please refer to your LINKS2X50, Skyroute, PC5400 ADT DVACS or PC5400 Sur-Gard DVACS Installation Manual for installation
and programming instructions.
[804] PC5132 Wireless Expansion Programming
Please refer to your PC5132 Installation Manual for programming locations and instructions.
[805] PC5100 Programming
Please refer to your PC5100 Installation Manual for programming locations and instructions.
[851] T-Link Programming
Please refer to your T-Link Installation Manual for programming locations and instructions.
NOTE: To enable T-Link, Option [5] in Section [382] must be ON.
24
Section 11: Special Installer Functions
[901] Installer Walk Test Mode Enable / Disable
[902] Module Supervision Reset
[903] Module Supervision Field
[904] Wireless Module Placement Test
For more information, please refer to your PC5132 Installation Manual
• Select the module / transmitter (Zones 01-32).
• Press [#] to Cancel.
Placement
Good
Led Keypad
Light 1 ON Steady
Bad
Light 3 ON Steady
LCD Keypad
“GOOD”
“BAD”
Bell / Buzzer
1 Beep / Squawk
3 Beeps / Squawks
[990] Installer Lockout Enable
[991] Installer Lockout Disable
[993] Restore Alternate Communicator (LINKS2X50, Skyroute, PC5400) to Factory Default Programming
[995] Restore Escort5580(TC) to Factory Default Programming
[996] Restore PC5132 to Factory Default Programming
[997] Restore PC5400 to Factory Default Programming
[998] Restore PC5936 to Factory Default Programming
[999] Restore PC5005 to Factory Default Programming
25
Appendix A: Programming LCD5500Z/
Keypads
If you have an LCD5500Z keypad, additional programming is required for proper operation. All LCD programming is done per
keypad. If more than one LCD keypad are present on the system, labels programmed at one keypad can be broadcast to all
other LCD keypads. Check the software version of the keypad you are programming, and refer to the correct programming
instructions.
LCD5500Z v2.x and Lower Keypads
The following is a description of the available programming
options and their accompanying programming sections:
How to Enter LCD Programming
Programming LCD keypads is similar to programming the rest of
the system. Follow the programming procedure as outlined in
Section 3 of the Installation Manual.
1. Enter keypad programming by pressing [*][8][Installer’s Code].
2. Press the [*] key.
3. Enter the two-digit section number to be programmed.
Programmable Labels
Zone labels and other LCD display identifiers can be customized
to make operation of the system easier for the end user. The following procedure should be used for creating all LCD labels:
1. Enter Installer’s Programming. Enter the two-digit section
number for the label to be programmed.
[01] to [32] Zone Labels (14 Characters)
Default: “Zone 1” - “Zone 32”
3. Use the arrow keys (<>) to move the underline bar underneath the letter to be changed.
4. Press the number key [1] to [9] corresponding to the letter
you require. The first time you press the number the first letter will appear. Pressing the number key again will display
the next letter. Refer to the following chart:
[1] - A, B, C, 1
[6] - P, Q, R, 6
[2] - D, E, F, 2
[7] - S, T, U, 7
[3] - G, H, I, 3
[8] - V, W, X, 8
[4] - J, K, L, 4
[9] - Y, Z, 9,0
[5] - M, N, O, 5
[0] - Space
5. When the required letter or number is displayed use the
arrow keys (<>) to scroll to the next letter.
6. When you are finished programming the Zone Label, press
the [*] key, scroll to “Save,” then press [*].
7. Continue from Step 2 until all Labels are programmed.
[33] Fire Alarm Label (14 Characters)
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
Default: “Fire Zone”
[34] and [35] Partition Labels (14 Characters)
Default: “System”
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
Default: “Partition 2”
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[40] Partition 1 and [41] Partition 2 “Command Output 1” Label (14 Characters)
Default: “Command_O/P_1”
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
Default: “Command_O/P_1”
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[44] Partition 1 and [45] Partition 2 “Command Output 2” Label (14 Characters)
Default: “Command_O/P_2”
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
Default: “Command_O/P_2”
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[46] Partition 1 and [47] Partition 2 “Command Output 3” Label (14 Characters)
Default: “Command_O/P_3”
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
Default: “Command_O/P_3”
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[48] Partition 1 and [49] Partition 2 “Command Output 4” Label (14 Characters)
Default: “Command_O/P_4”
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
Default: “Command_O/P_4”
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[51] Fail to Arm Event Message
Default: “System Has Failed to Arm”
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[52] Alarm When Armed Event Message
Default: “Alarm Occurred While Armed < >” I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
26
Special Installer Functions:
[60]
First User Display Mask
Default
Option ON
I_______I
1
Hold [P]anic Keys prompt ON
ON
OFF
Hold [P]anic Keys prompt OFF
ON
I_______I
2
Zone Bypassing prompt ON
Zone Bypass prompt OFF
ON
I_______I
3
Troubles prompt ON
Troubles prompt OFF
ON
I_______I
4
Alarm Memory prompt ON
Alarm Memory prompt OFF
ON
I_______I
5
Door Chime Control prompt ON
Door Chime Control prompt OFF
ON
I_______I
6
Access Codes prompt ON
Access Codes prompt OFF
ON
I_______I
7
User Functions prompt ON
User Functions prompt OFF
ON
I_______I
8
Output Control prompt ON
Output Control prompt OFF
[61]
Second User Display Mask
Default
Option ON
OFF
I_______I
1
Installer Programming prompt ON
OFF
Installer Programming prompt OFF
ON
I_______I
2
Stay Arm prompt ON
Stay Arm prompt OFF
ON
I_______I
3
Quick Arm prompt ON
Quick Arm prompt OFF
ON
I_______I
4
Interior Arm prompt ON
Interior Arm prompt OFF
OFF
I_______I
5
Quick Exit prompt ON
Quick Exit prompt OFF
View Event Buffer prompt OFF
ON
I_______I
6
View Event Buffer prompt ON
OFF
I_______I
7
For Future Use
OFF
I_______I
8
Music Input ON
[62]
Third User Display Mask
Default
Option ON
ON
I_______I
1
System Test prompt ON
Music Input OFF
OFF
System Test prompt OFF
ON
I_______I
2
Time and Date prompt ON
Time and Date prompt OFF
ON
I_______I
3
Auto-Arm Control prompt ON
Auto-Arm Days prompt OFF
ON
I_______I
4
Auto-Arm Time prompt ON
Auto-Arm Time prompt OFF
ON
I_______I
5
Download Enable prompt ON
Download Enable prompt OFF
ON
I_______I
6
Bright Control prompt ON
Bright Control prompt OFF
ON
I_______I
7
Contrast Control prompt ON
Contrast Control prompt OFF
ON
I_______I
8
Buzzer Control prompt ON
Buzzer Control prompt OFF
[63]
Downloaded LCD Message Duration
Default: 003 I_______I_______I_______I (Valid entries are 000-255, 000=Unlimited Message Display. This number represents the number of
times the Downloaded message is cleared by pressing any key while the message is up after timeout)
[64]
Key Options
Default
Option
ON
I_______I
1
ON
[F]ire Keys enabled
OFF
[F]ire Keys disabled
ON
I_______I
2
[A]uxiliary Keys enabled
[A]uxiliary Keys disabled
ON
I_______I
3
[P]anic Keys enabled
[P]anic Keys disabled
OFF
I_______I
4-8
For Future Use
[65]
Fourth User Display Mask
Default
Option ON
ON
I_______I
1
User Initiated Call-up prompt ON
OFF
User Initiated Call-up prompt OFF
OFF
I_______I
2
For Future Use
OFF
I_______I
3
For Future Use
ON
I_______I
4
Command Output #1 prompt ON
Command Output #1 prompt OFF
ON
I_______I
5
Command Output #2 prompt ON
Command Output #2 prompt OFF
OFF
I_______I
6
Command Output #3 prompt ON
Command Output #3 prompt OFF
OFF
I_______I
7
Command Output #4 prompt ON
Command Output #4 prompt OFF
OFF
I_______I
8
For Future Use
27
[66]
Keypad Options
Default
Option
I_______I
1
ON
ON
Display Access Code when Programming
OFF
Display ‘X’ when Programming
ON
I_______I
2
Local Clock Display Enabled
Local Clock Display Disabled
OFF
I_______I
3
Local Clock Displays 24 Hour time
Local Clock Displays AM/PM
ON
I_______I
4
Auto Alarm Memory Scroll Enabled
Auto Alarm Memory Scroll Disabled
OFF
I_______I
5
Local Display of Temperature Enabled*
Local Display of Temperature Disabled
OFF
I_______I
6
Bypass Options prompt ON
Bypass Options prompt OFF
OFF
I_______I
7-8
For Future Use
[67] Fifth User Display Mask
Default
Option ON
OFF
I_______I
1
Thermostat CTRL Prompt ON*
OFF
Thermostat CTRL Prompt OFF
OFF
I_______I
2
Temperature Setting Prompt ON*
Temperature Setting Prompt OFF
OFF
I_______I
3
Occupancy Mode Prompt ON*
Occupancy Mode Prompt OFF
OFF
I_______I
4
Thermostat Mode Prompt ON*
Thermostat Mode Prompt OFF
OFF
I_______I
5
Fan Control Prompt ON*
Fan Control Prompt OFF
OFF
I_______I
6
For Keypad View Prompt ON*
For Keypad View Prompt OFF
OFF
I_______I
7-8
For Future Use
[68] Sixth User Display Mask
Default
Option ON
OFF
I_______I
1
Occupancy Mode Auxiliary Prompt ON*
OFF
Occupancy Mode Auxiliary Prompt OFF
OFF
I_______I
2
Occupancy Mode Day Prompt ON*
Occupancy Mode Day Prompt OFF
OFF
I_______I
3
Occupancy Mode Away Prompt ON*
Occupancy Mode Away Prompt OFF
OFF
I_______I
4
Occupancy Mode Night Prompt ON*
Occupancy Mode Night Prompt OFF
OFF
I_______I
5-8
For Future Use
NOTE: These options are only relevant if you are using an LCD5500Z v2.1 or higher.
[97]
View Software Version
[98] Initiate Global Label Broadcast
All LCD programming is done per keypad. If more than one LCD keypad are present on the system, and the PC5400 receives
labels, labels programmed at one keypad can be broadcast to all other LCD keypads. Perform the following procedure in order to
broadcast labels:
Step 1 - Program one LCD keypad completely.
Step 2 - Make sure all LCD keypads are connected to the Keybus.
Step 3 - Enter Keypad Programming, then enter section [98] at the keypad that was programmed. The keypad will now broadcast
all the information programmed to all the other LCD keypads on the system.
Step 4 - When the keypad is finished press the [#] key to exit.
[99] Reset LCD EEPROM to Factory Defaults
ASCII Characters
LCD5500Z v3.0 and Higher Keypads
The following is a description of the available programming
options and their accompanying programming sections:
How to Enter LCD Programming
Programming LCD keypads is similar to programming the rest of
the system. Follow the programming procedure as outlined in
Section 3 of the Installation Manual.
1. Enter keypad programming by pressing [*][8][Installer’s
Code].
2. Press the [*] key.
28
3. Enter the three-digit section number to be programmed.
Special Installer Functions:
Refer to the following chart:
Programmable Labels
[1] - A, B, C, 1
[6] - P, Q, R, 6
Zone labels and other LCD display identifiers can be customized to
[2] - D, E, F, 2
[7] - S, T, U, 7
make operation of the system easier for the end user. The following
[3] - G, H, I, 3
[8] - V, W, X, 8
procedure should be used for creating all LCD labels:
[4] - J, K, L, 4
[9] - Y, Z, 9,0
1. Enter Installer’s Programming. Enter the three-digit section num[5] - M, N, O, 5
[0] - Space
ber for the label to be programmed.
4. When the required letter or number is displayed use the arrow
2. Use the arrow keys (<>) to move the underline bar underneath
keys (<>) to scroll to the next letter.
the letter to be changed.
5.
When you are finished programming the Zone Label, press the [*]
3. Press the number key [1] to [9] corresponding to the letter you
key, scroll to “Save,” then press [*].
require. The first time you press the number the first letter will
6. Continue from Step 2 until all Labels are programmed.
appear. Pressing the number key again will display the next letter.
[001] to [032] Zone Labels (14 Characters)
Default: “Zone 1” - “Zone 32”
[065] Fire Alarm Label (14 Characters)
Default: “Fire Zone”I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[066] Fail to Arm Event Message
Default: “System Has Failed to Arm” I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[067] Alarm When Armed Event Message
Default: “Alarm Occurred While Armed < >”I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[070] First User Display Mask
Default
Option ON
OFF
ON I_______I
1
Hold [P]anic Keys prompt ON
Hold [P]anic Keys prompt OFF
ON I_______I
2
Zone Bypassing prompt ON
Zone Bypass prompt OFF
ON I_______I
3
Troubles prompt ON
Troubles prompt OFF
ON I_______I
4
Alarm Memory prompt ON
Alarm Memory prompt OFF
ON I_______I
5
Door Chime Control prompt ON
Door Chime Control prompt OFF
ON I_______I
6
Access Codes prompt ON
Access Codes prompt OFF
ON I_______I
7
User Functions prompt ON
User Functions prompt OFF
ON I_______I
8
Output Control prompt ON
Output Control prompt OFF
[071] Second User Display Mask
Default
Option ON
OFF
OFF I_______I
1
Installer Programming prompt ON
Installer Programming prompt OFF
2
Stay Arm prompt ON
Stay Arm prompt OFF
ON I_______I
3
Quick Arm prompt ON
Quick Arm prompt OFF
ON I_______I
ON I_______I
4
Interior Arm prompt ON
Interior Arm prompt OFF
5
Quick Exit prompt ON
Quick Exit prompt OFF
OFF I_______I
6
View Event Buffer prompt ON
View Event Buffer prompt OFF
ON I_______I
OFF I_______I
7
For Future Use
8
Music Input ON
Music Input OFF
OFF I_______I
[072] Third User Display Mask
Default
Option ON
OFF
I_______I
1
System Test prompt ON
System Test prompt OFF
ON
ON
I_______I
2
Time and Date prompt ON
Time and Date prompt OFF
I_________I
3
Auto-Arm Control prompt ON
Auto-Arm Days prompt OFF
ON
ON
I_________I
4
Auto-Arm Time prompt ON
Auto-Arm Time prompt OFF
ON
I_________I
5
Download Enable prompt ON
Download Enable prompt OFF
I_________I
6
Bright Control prompt ON
Bright Control prompt OFF
ON
ON
I_________I
7
Contrast Control prompt ON
Contrast Control prompt OFF
I_________I
8
Buzzer Control prompt ON
Buzzer Control prompt OFF
ON
[073] Downloaded LCD Message Duration
Default: 003 I_______I_______I_______I (Valid entries are 000-255, 000=Unlimited Message Display. This number represents the number of
times the Downloaded message is cleared by pressing any key while the message is up after timeout)
[074] Key Options
Default
Option ON
OFF
I_______I
1
[F]ire Keys enabled
[F]ire Keys disabled
ON
ON
I_______I
2
[A]uxiliary Keys enabled
[A]uxiliary Keys disabled
I_______I
3
[P]anic Keys enabled
[P]anic Keys disabled
ON
I________I
4-8
For Future Use
OFF
29
[075] Fourth User Display Mask
Default
Option ON
I_______I
1
User Initiated Call-up prompt ON
ON
OFF
User Initiated Call-up prompt OFF
OFF
I_______I
2
Last Code to Disarm/Arm prompt ON
Last Code to Disarm/Arm prompt OFF
OFF
I_______I
3
Walk Test Prompt ON
Walk Test Prompt ON
ON
I_______I
4
Command Output #1 prompt ON
Command Output #1 prompt OFF
ON
I_______I
5
Command Output #2 prompt ON
Command Output #2 prompt OFF
OFF
I_______I
6
Command Output #3 prompt ON
Command Output #3 prompt OFF
OFF
I_______I
7
Command Output #4 prompt ON
Command Output #4 prompt OFF
OFF
I_______I
8
For Future Use
[076] Keypad Options
Default
Option
ON
I_______I
1
ON
Display Access Code when Programming
OFF
Display ‘X’ when Programming
ON
I_______I
2
Local Clock Display Enabled
Local Clock Display Disabled
OFF
I_______I
3
Local Clock Displays 24 Hour time
Local Clock Displays AM/PM
ON
I_______I
4
Auto Alarm Memory Scroll Enabled
Auto Alarm Memory Scroll Disabled
OFF
I_______I
5
Local Display of Temperature Enabled*
Local Display of Temperature Disabled
OFF
I_______I
6
Bypass Options prompt ON
Bypass Options prompt OFF
OFF
I_______I
7
For Future Use
OFF
I_______I
8
Auto Scroll Open Zones Enabled
[077] Fifth User Display Mask
Default
Option ON
OFF
I_______I
1
Thermostat CTRL Prompt ON*
Auto Scroll Open Zones Disabled
OFF
Thermostat CTRL Prompt OFF
OFF
I_______I
2
Temperature Setting Prompt ON*
Temperature Setting Prompt OFF
OFF
I_______I
3
Occupancy Mode Prompt ON*
Occupancy Mode Prompt OFF
OFF
I_______I
4
Thermostat Mode Prompt ON*
Thermostat Mode Prompt OFF
OFF
I_______I
5
Fan Control Prompt ON*
Fan Control Prompt OFF
OFF
I_______I
6
For Keypad View Prompt ON*
For Keypad View Prompt OFF
OFF
I_______I
7-8
For Future Use
[078] Sixth User Display Mask
Default
Option ON
OFF
I_______I
1
Occupancy Mode Auxiliary Prompt ON*
OFF
Occupancy Mode Auxiliary Prompt OFF
OFF
I_______I
2
Occupancy Mode Day Prompt ON*
Occupancy Mode Day Prompt OFF
OFF
I_______I
3
Occupancy Mode Away Prompt ON*
Occupancy Mode Away Prompt OFF
OFF
I_______I
4
Occupancy Mode Night Prompt ON*
Occupancy Mode Night Prompt OFF
OFF
I_______I
5-8
For Future Use
NOTE: These options are only relevant if you are using an LCD5500Z v2.1 or higher.
Partition Labels
Default: “System” - “Partition 8”
Section
Partition
Label
[101]
1/System
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[102]
2
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[103]
3
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[104]
4
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[105]
5
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[106]
6
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[107]
7
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[108]
8
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
30
Special Installer Functions:
Command Output Labels
Default: “Command_O/P_1” - “Command_O/P_4”
Program a label for each Command Output used, as it will appear at each partition ( of the Installation Manual).
Section
Partition
Command Output
Label
[120]
1
1
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[121]
1
2
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[122]
1
3
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[123]
1
4
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[124]
2
1
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[125]
2
2
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[126]
2
3
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[127]
2
4
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[128]
3
1
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[129]
3
2
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[130]
3
3
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[131]
3
4
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[132]
4
1
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[133]
4
2
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[134]
4
3
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[135]
4
4
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[136]
5
1
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[137]
5
2
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[138]
5
3
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[139]
5
4
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[140]
6
1
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[141]
6
2
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[142]
6
3
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[143]
6
4
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[144]
7
1
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[145]
7
2
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[146]
7
3
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[147]
7
4
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[148]
8
1
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[149]
8
2
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[150]
8
3
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
[151]
8
4
I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I_____I
31
[997] View Software Version
[998] Initiate Global Label Broadcast
All LCD programming is done per keypad. If more than one LCD keypad are present on the system, and the PC5400 receives
labels, labels programmed at one keypad can be broadcast to all other LCD keypads. Perform the following procedure in order to
broadcast labels:
Step 1 - Program one LCD keypad completely.
Step 2 - Make sure all LCD keypads are connected to the Keybus.
Step 3 - Enter Keypad Programming, then enter section [998] at the keypad that was programmed. The keypad will now broadcast
all the information programmed to all the other LCD keypads on the system.
Step 4 - When the keypad is finished press the [#] key to exit.
[999]
Reset LCD EEPROM to Factory Defaults
ASCII Characters
32
Appendix B: Programming LCD5501Z Keypads
There are several programming options available for the LCD5501Z keypad. These are described below. Record all your programming choices in the programming worksheets included in this manual.
Programming Keypad Options
Programming the LCD5501Z is similar to programming the rest
of the system. To change the keypad programming:
1.
2.
3.
4.
Enter [*][8][Installer’s code]
Enter [000] to go to keypad programming
Enter section number [6] or [7].
To turn any of the options on or off, press the option number
(from [1] to [8]).
5. When you are finished programming, press [#].
When you are in the LCD5501Z programming sections, the keypad will display which options are turned on along the top of the
display. To turn an option on or off, press the number corresponding to the option on the number pad. The numbers of the
options that are currently turned ON will be displayed.
For example, if options 1 and 2 are on, the display will look like:
Clock Options
The LCD5501Z will display the current time after 30 seconds of
no key presses. To set the correct time and date for the system,
please refer to the Power864 User’s Guide. You can change how
the keypad displays the time with options [1] to [3] in programming section [6].
NOTE: If the time does not display on keypad option is selected, make sure that the Keypad displays time when zones are open
option is also selected.
Alarms Displayed While Armed Option
You can disable the display of alarms on the keypad when the
system is armed. The display of alarms is enabled by default. To
disable the display of alarms when the system is armed, turn off
section [6], option [5].
off on the keypad, enter section [7], and turn on or off options
[1] to [3].
Emergency Key Options
You can enable or disable the Fire, Auxiliary and Panic keys at
each keypad. These keys are enabled by default. Please see the
Power864 Installation Manual for more information on these
keys and their options. To turn any of the emergency keys on or
To change the door chime opening/closing settings, at each
LCD5501Z keypad, enter section [6], and turn on or off options
[6] and [7].
[6] LCD5501Z Keypad Options
Default
Option On
Door Chime on Zone Openings/Closings
By default, LCD5501Z keypads are programmed to sound door
chimes on both zone openings and closings.
Off
ON
I________I
1
Local Clock Display Enabled
ON
I________I
2
Local Clock Displays AM/PM
Local Clock Displays 24-hr Time
OFF
I________I
3
Open Zones Override Clock Display
Open Zones Do Not Override Clock
OFF
I________I
4
Scandinavian Approvals enabled
Scandinavian Approvals disabled
OFF
I________I
5
Alarms Not Displayed While Armed
Alarms Always Displayed While Armed
OFF
I________I
6
Door Chime Enabled for Zone Openings
Door Chime Disabled for Zone Openings
OFF
I________I
7
Door Chime Enabled for Zone Closings
Door Chime Disabled for Zone Closings
OFF
I________I
8
For Future Use
[7] Emergency Key Options
Default
Option On
ON
I________I
ON
I________I
ON
I________I
OFF
I________I
4-8
1
Local Clock Display Disabled
Off
[F] Key Enabled
[F] Key Disabled
2
[A] Key Enabled
[A] Key Disabled
3
[P] Key Enabled
[P] Key Disabled
For Future Use
33
Programming Door Chime Options
You can program the LCD5501Z keypad to sound a tone when
any zone is opened or closed. There are two parts to the
LCD5501Z door chime programming:
• Program if the LCD5501Z will chime when zones are opened
and/or closed (see ).
• Program the type of sound the LCD5501Z will make when an
individual zone is opened or closed.
For the door chime feature to work, you will also need to turn on
the Door Chime attribute for each zone that will trigger the
chime. This programming is done in the control panel software.
Refer to the Power864 Installation Manual for more information.
Door Chime Sounds
You can program the LCD5501Z keypad to make different door
chime sounds for individual zones, or groups of zones. Each
LCD5501Z keypad can make any of four door chime sounds for
each zone that triggers the door chime:
• ·3 quick beeps (default sound)
• ·‘Bing – Bing’ tone
• ·‘Ding – Dong’ tone
• ·‘Alarm’ tone
NOTE: For a zone to be able to trigger the door chime sound,
the Door Chime zone attribute must also be enabled in the
control panel programming. Please see your Power864 Installation Manual.
To change the door chime sounds:
1. Enter [*][8][Installer’s code].
2. Enter [*] to go to door chime sound programming.
3. Enter the 2-digit number for the zone you are programming
[01] - [64].
NOTE: LCD5501Z v 1.x keypads only support zones 1 to 32.
4. Turn one of the following options on by pressing [1], [2], [3],
[2]‘Bing – Bing’ tone
or [4]:
[3]‘Ding – Dong’ tone
[4]‘Alarm’ tone
[1] 6 quick beeps (default sound)
NOTE: Make sure that only one of the above options is turned on. If more than one is on, the keypad will sound the first option that
is enabled. If none of the options are selected, the keypad will not make any sound when the zone is opened or closed.
5. To program the door chime sound for another zone, repeat
steps 3 and 4.
6. When you are finished programming the door chime sounds,
press [#] to exit.
34
Special Installer Functions:
Door Chime Sound Programming
Zone
Location
Options:
[1]
[2]
[3]
3 Beeps
(default)
“Bing-bing”
“Ding-dong”
[4]
Alarm tone
[01]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[02]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[03]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[04]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[05]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[06]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[07]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[08]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[09]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[10]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[11]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[12]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[13]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[14]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[15]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[16]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[17]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[18]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[19]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[20]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[21]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[22]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[23]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[24]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[25]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[26]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[27]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[28]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[29]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[30]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[31]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
[32]
I__________________________________________________________________I
I________I
I________I
I________I
I________I
35
©2001 Digital Security Controls Ltd.
Toronto, Canada • www.dsc.com
Printed in Canada 29005955 R001