Owner’s manual & Installation manual
Mode d’emploi et manuel d’installation
Benutzerhandbuch & Installationshandbuch
Manuale dell’utente e manuale di installazione
Gebruikershandleiding en installatiehandleiding
Manual de instrucciones y de instalación
Ägar- & installationshandbok
Manual do utilizador e manual de instalação
Betjeningsvejledning og installationsvejledning
VZ709E
DVD MULTIMEDIA STATION WITH
7-inch TOUCH PANEL CONTROL
STATION MULTIMEDIA DVD AVEC COMMANDE PAR
ECRAN TACTILE 7 pouces
DVD-MULTIMEDIA-STATION MIT
7-Zoll-TOUCHSCREEN-STEUERUNG
STAZIONE MULTIMEDIALE DVD DOTATA DI PANNELLO DI
CONTROLLO A SFIORAMENTO DA 7 POLLICI
DVD MULTIMEDIA STATION MET
7-inch TOUCH PANEL BEDIENING
EQUIPO DVD MULTIMEDIA CON
PANEL DE CONTROL TÁCTIL DE 7 pulgadas
DVD MULTIMEDIA-STATION MED
7-tums PEKSKÄRM
ESTAÇÃO MULTIMÉDIA DE DVD COM CONTROLO DE
PAINEL DIGITAL DE 7 polegadas
DVD MULTIMEDIESTATION MED 7" BERØRINGSPANEL
CAUTIONS:
This appliance contains a laser system and is
classified as a “CLASS 1 LASER PRODUCT”.
To use this model properly, read this Owner’s
Manual carefully and keep this manual for
your future reference. In case of any trouble
with this player, please contact your nearest
“AUTHORIZED service station”. To prevent
direct exposure to the laser beam, do not try
to open the enclosure.
!CAUTION
USE OF CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED IN THE OWNER’S
MANUAL MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
ADVARSEL.
Denne mærking er anbragt udvendigt på
apparatet og indikerer, at apparatet arbejder
med laserstråler af klasse 1, hvilket betyder,
at der anvendes laserstråler af svageste
klasse, og at man ikke på apparatets yderside
kan blive udsat for utilladelig kraftig stråling.
APPARATET BØR KUN ÅBNES AF FAGFOLK
MED SÆRLIGT KENDSKAB TIL APPARATER
MED LASERSTRÅLER!
Indvendigt i apparatet er anbragt den her
gengivne advarselsmækning, som advarer
imod at foretage sådanne indgreb i apparatet,
at man kan komme til at udsaætte sig for
laserstråling.
OBS!
Apparaten innehåller laserkomponenten som
avger laserstrålning överstigande gränsen
för laserklass 1.
VAROITUS
Suojakoteloa si saa avata. Laite sisältää
laserdiodin, joka lähettää näkymätöntä
silmille vaarallista lasersäteilyä.
Thank you for purchasing the Clarion VZ709E.
English
• Please read this owner’s manual thoroughly before operating this equipment.
• After reading this manual, be sure to keep it in a handy place (e.g., glove compartment).
• Check the contents of the enclosed warranty card and keep it carefully with this manual.
Contents
VZ709E
1
Owner’s manual
1. FEATURES .................................................................................................................... 2
Expanding Systems........................................................................................................ 2
Playable discs ................................................................................................................ 3
DVD video features ........................................................................................................ 4
2. PRECAUTIONS ............................................................................................................. 5
Liquid crystal panel/Generalities..................................................................................... 6
Cleaning ......................................................................................................................... 6
About the registered marks, etc. .................................................................................... 7
3. CONTROLS ................................................................................................................... 8
Functions of Buttons....................................................................................................... 8
Outline of Button and Touchkey Operation .................................................................. 10
Remote Control Unit ..................................................................................................... 16
4. BASIC OPERATIONS.................................................................................................. 18
DCP (Detachable Control Panel).................................................................................. 18
Turning On and Off the Power ..................................................................................... 19
Adjusting the Volume ................................................................................................... 19
Opening the Liquid Crystal Panel and Adjusting the Angle .......................................... 19
Turning the Audio OFF ................................................................................................. 21
Turning the Monitor OFF .............................................................................................. 21
Setting/Ejecting a Disc ................................................................................................. 21
Connecting/Disconnecting an USB Media Device........................................................ 23
Selecting a Media Source ............................................................................................ 25
2Zone Function ............................................................................................................ 26
5. SOURCE OPERATIONS ............................................................................................. 27
Radio Operations ......................................................................................................... 27
DVD Video Operations ................................................................................................. 32
Audio CD Operations ................................................................................................... 39
MP3/WMA/AAC Operations ......................................................................................... 41
DivX Operations ........................................................................................................... 44
6. SOURCE OPERATIONS (ACCESSORIES)................................................................ 46
iPod Operations............................................................................................................ 46
USB Memory Operations.............................................................................................. 50
Bluetooth Audio Player Operations .............................................................................. 51
Bluetooth Telephone Operations.................................................................................. 53
Navigation System Operations ..................................................................................... 57
AUX Operations ........................................................................................................... 58
7. SYSTEM SETTINGS.................................................................................................... 59
Audio Settings .............................................................................................................. 59
General Settings........................................................................................................... 62
Adjusting the Monitor.................................................................................................... 64
8. TROUBLESHOOTING ................................................................................................. 65
9. ERROR DISPLAYS...................................................................................................... 67
10. SPECIFICATIONS ....................................................................................................... 69
INSTALLATION AND WIRE CONNECTION MANUAL ................................................... 70
English
1. FEATURES
Owner’s manual
■ Built in Bluetooth® Handsfree (HFP & OPP) and Audio Streaming (A2DP & AVRCP)
■ USB Direct Connection for iPod®
■ NAX983HD (CeNET HDD Navigation) and NP509E (Hide-away Navigation) Control with Touch
Panel
Expanding Systems
Expanding audio features
Expanding visual features
Rear Vision Camera
(CC2011E/CAA185)
Rear Monitor
4-Channel Amplifier
VTR etc.
iPod
Bluetooth
Telephone
USB Memory
Bluetooth
Audio Player
Note:
The items listed outside of the frames are
the commercial products generally sold.
NP509E
NAX983HD/NAX973HD/NAX963HD
Expanding navigation features
2
VZ709E
English
Playable discs
This DVD player can play the following discs:
Playable discs
Audio CDs
Owner’s manual
DVD video discs
CD TEXT
In addition, the DVD player can play CD-R/RW, DVD-R/RW, and DVD+R/RW discs on which the
following media files have been recorded:
Playable media files
MP3 ID3 TAG
WMA
AAC
DivX
For detailed information, see the sections entitled “MP3/WMA/AAC Operations” (page 41) and “DivX
Operations” (page 44).
About CD Extra discs
Discs that cannot be played back
A CD Extra disc is a disc in which a total of two
sessions have been recorded. The first session is
Audio session and the second session is Data
session.
Your personally-created CDs with more than
second data sessions recorded cannot be played
on this DVD player.
This player cannot play DVD Audio, DVD-RAM,
Video CDs, Photo CDs, etc.
Note:
• When you play a CD Extra disc, only the first
session will be recognized.
About playing a CD-R/RW disc
This player can play CD-R/RW discs previously
recorded in Audio CD format or format with MP3/
WMA/AAC/DivX files.
About playing a DVD-R/RW or
DVD+R/RW disc
This player can play DVD-R/RW and DVD+R/RW
discs previously recorded in DVD video format or
format with MP3/WMA/AAC/DivX files.
Note:
• It may not be possible to play back discs recorded
on some CD/DVD drive units. (Cause: disc
characteristics, cracks, dust/dirt, dust/dirt on
player’s lens, etc.)
• If a CD-R/RW, DVD-R/RW, or DVD+R/RW disc
that has not been finalized is played, it will take a
long time to start playing. Also, it may not be
possible to play depending on its recording
conditions.
• You cannot play Super Audio CDs. Playback of the
CD player is not supported even if it is a hybrid
disc.
Note on region numbers of DVD
video discs
The DVD video system assigns a region number
to DVD players and DVD discs by sales area.
The DVD video region number playable in this
system is marked on the disc jacket as shown
below.
ALL
2
2
4
6
VZ709E
3
English
DVD video features
This unit provides the following functions in
addition to the high image quality and sound
quality of DVD video.
Owner’s manual
Note:
• The functions described in this section differ
depending on the DVD video disc. Refer to the
instructions provided with the DVD video.
• Some disc functions may operate differently from
described in this manual.
Multi-sound function
DVD video can store up to 8 languages for one
film; select the language of your preference.
• The languages stored on the disc are indicated
by the icon shown below.
Multi-angle function
A DVD video that is filmed from multiple angles
allows you to select the angle of choice.
• The number of recorded angles is indicated by
the icon shown below.
Subpicture (subtitles) function
A DVD video can record subtitles for up to 32
languages and you can select the language of
the subtitles you wish to see.
• The number of recorded subtitle languages is
indicated by the icon shown below.
4
VZ709E
Multi-story function
When a DVD video contains more than one story
for a film, you can select the story you wish to
enjoy. The operation procedures vary with the
disc; observe the instructions for selecting a story
provided during playback.
DVD menu
DVD Menus can be called up during DVD video
playback to perform menu setting.
• Example showing DVD menu
English
2. PRECAUTIONS
WARNING
1. When the inside of the car is very cold and the
player is used soon after switching on the
heater, moisture may form on the disc (DVD/
CD) or the optical parts of the player and
proper playback may not be possible. If
moisture forms on the disc (DVD/CD), wipe it
off with a soft cloth. If moisture forms on the
optical parts of the player, do not use the
player for about one hour. The condensation
will disappear naturally allowing normal
operation.
INFORMATION FOR USERS:
CHANGES OR MODIFICATIONS TO THIS
PRODUCT NOT APPROVED BY THE
MANUFACTURER WILL VOID THE
WARRANTY.
2. Driving on extremely bumpy roads which
cause severe vibration may cause the sound
to skip.
3. This unit uses a precision mechanism. Even
in the event that trouble arises, never open
the case, disassemble the unit, or lubricate
the rotating parts.
VZ709E
5
Owner’s manual
For your safety, the driver should not watch the DVD video/movie data or operate the controls
while driving. Please note that watching and operating the DVD video/movie data while driving
are prohibited by law in some countries. Also, while driving, keep the volume to a level at which
external sounds can be heard.
English
Liquid crystal panel/Generalities
For a longer service life, be sure to read the following cautions.
Owner’s manual
• Be sure to house the liquid crystal panel inside
the main unit when parking the car outdoors for
a long period of time. The liquid crystal panel
will operate properly in a temperature range of
0 to 60qC.
• Do not allow any liquids on the set from drinks,
umbrellas, etc. Doing so may damage the
internal circuitry.
• Do not disassemble or modify the set in any
way. Doing so may result in damage.
• Do not draw the liquid crystal panel out and use
it as a tray. Also, subjecting the liquid crystal
panel to shocks may result in breakage,
deformation, or other damage.
• Do not let cigarettes burn the display. Doing so
may damage or deform the cabinet.
• If a problem should occur, have the set
inspected at your store of purchase.
• Do not insert objects or poke in the space
between the liquid crystal panel and the main
unit when the panel is tilted.
Cleaning
• Cleaning the cabinet
Use a soft and dry cloth and gently wipe off the
dirt. For tough dirt, apply some neutral
detergent diluted in water to a soft cloth, wipe
off the dirt gently, then wipe again with a dry
cloth.
Do not use benzene, thinner, car cleaner, etc.,
as these substances may damage the cabinet
or cause the paint to peel. Also, leaving rubber
or plastic products in contact with the cabinet
for long periods of time may cause stains.
• Cleaning the liquid crystal panel
The liquid crystal panel tends to collect dust, so
wipe it off occasionally with a soft cloth. The
surface is easily scratched, so do not rub it with
hard objects.
6
VZ709E
• Do not place anything on the display when the
panel is tilted.
• The remote control unit may not work if the
remote control sensor is exposed to direct
sunlight.
• In extremely cold weather, the display
movement may slow down and the display may
darken, but this is not a malfunction. The
display will work normally when the
temperature increases.
• Small black and shiny spots inside the liquid
crystal panel are normal for LCD products.
• The liquid crystal panel may stop temporarily
when it opens or closes, when the engine stops
or when it is cold.
• The touchkeys on the display operate when
slightly touched. Do not press the touchkey
screen with much force.
• Do not push the case surrounding the touchkey
panel with much force. This may cause
malfunctioning of the touchkeys.
English
About the registered marks, etc.
Owner’s manual
• This product incorporates copyright protection
technology that is protected by U.S. patents
and other intellectual property rights. Use of
this copyright protection technology must be
authorized by Macrovision, and is intended for
home and other limited viewing uses only
unless otherwise authorized by Macrovision.
Reverse engineering or disassembly is
prohibited.
• Manufactured under license from Dolby
Laboratories.
“Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
• Windows Media™, and the Windows® logo are
trademarks, or registered trademarks of
Microsoft Corporation in the United States and/
or other countries.
• “DivX”, “DivX Certified”, and associated logos
are trademarks of DivX, Inc., and are used
under license.
• “Made for iPod” means that an electronic
accessory has been designed to connect
specifically to iPod and has been certified by
the developer to meet Apple performance
standards.
Apple is not responsible for the operation of
this device or its compliance with safety and
regulatory standards.
iPod is a trademark of Apple Inc., registered in
the U.S. and other countries.
VZ709E
7
English
3. CONTROLS
Sensor
Owner’s manual
[OPEN]
[VOL –], [VOL +]
[TA]
[SRC]
[MAP]
[MENU]
Note:
The control panel can be detached to prevent theft. For details, see the pages of “DCP (Detachable Control
Panel)” (page 18).
Functions of Buttons
Note:
• Be sure to read this section while referring to the front diagram.
Sensor
• Receiver for the remote control unit (operating
range: 30° in all directions).
[o] (EJECT) button
• Use this button to eject the disc set in this unit.
[VOL –], [VOL +] buttons
• Use these buttons to increase/decrease the
volume.
[SRC] button
• When the liquid crystal panel is closed, press
this button to change to the next source mode
such as TUNER mode.
• When the liquid crystal panel is open, press
this button to display the Source screen to
switch the source mode.
• Keep pressing this button more than 1 second
to turn off the audio feature (AUDIO OFF).
Press this button to turn on the audio feature.
[R], [F] buttons
• Use these buttons to change to the previous/
next preset station in the TUNER mode.
8
VZ709E
• In the DVD Video mode, use these buttons to
select a chapter to be played.
Keep pressing a button during playback
performs the fast backward or fast forward
playback.
Keep pressing the [F] button during pausing
performs the slow playback.
• In the CDDA, MP3/WMA/AAC/DivX, and iPod/
USB Memory/Bluetooth (Audio) modes, use
these buttons to select a track to be played.
Keep pressing a button during playback
performs the fast backward or fast forward
playback.
[MENU] button*1
• Press this button to display the Menu screen.
You can change the system settings from this
screen.
[MAP] button*2
• Pressing this button in the audio/visual modes
changes to the Navigation mode.
Functions of Buttons
[OPEN] button
• Use this button to open/close the liquid crystal
panel.
• Keep pressing this button more than 2 seconds
so that the liquid crystal panel is positioned
horizontally when the liquid crystal panel is
open (Air Conditioner Operation mode).
• When the liquid crystal panel is closed, keep
pressing this button more than 5 seconds to
perform the panel calibration function to
memorize the maximum angle of the liquid
crystal panel.
Blink LED
Blink LED
• When the Blink LED function is set to “ON” from
the System tab menu on the General Settings
screen, blinks when the DCP (Detachable
Control Panel) is removed.
VZ709E
9
Owner’s manual
[TA] button
• Press this button to turn on/off the TA (Traffic
Announcement) standby mode.
• Keep pressing this button more than 1 second
to turn on/off the Auto Antenna function (see
page 63).
Note:
*1 This button does not work when the liquid crystal
panel is closed.
*2 This button is available only when a navigation
system is connected.
*3 This button is available only when a navigation
system is connected or the connection with a
Bluetooth telephone is established. However, the
Voice Command operation is not possible with
the navigation system NP509E.
English
[ ] (Voice/SEND/END) button*3
• When a call comes in, press this button to
answer the call.
• During a call, press this button to end the call.
• When a navigation system is connected, press
this button to display the Voice Command
screen of the navigation system.
English
Outline of Button and Touchkey Operation
Turning the power on
Owner’s manual
Engine ON
position
∗1
When the liquid crystal
panel is open
When the liquid crystal
panel is closed
System check
The CeNET format utilized on this unit is provided
with a system check function. When the system
check function is performed under the following
conditions, the power is automatically turned off.
Press the [SRC] button again.
• When power is first turned on after initial
installation.
• When an external device is connected or
disconnected.
• When Reset button is pressed.
* In addition to the above conditions, the system
check function can be performed from the System
tab menu on the General settings screen.
or
Note:
*1 These images indicate the buttons to press or
keys to touch.
You can change the media
sources.
10
VZ709E
Outline of Button and Touchkey Operation
English
TUNER mode operation
(Source screen)
Owner’s manual
Switches the radio band.
Selects Home/Travel modes.
Manual tuning
Seek tuning
(Options screen)
(Preset List screen)
(PTY Select screen)
• Select desired station after
selecting radio band.
(PTY Item screen)
VZ709E
11
Outline of Button and Touchkey Operation
English
DVD Video mode operation
(DVD Video mode screen) *2
Owner’s manual
(Source screen)
* Screen during DVD Video mode
when automobile moving.
(Options screen)
(DVD Setup screen)
Note:
*2 When playing a DVD video movie, touching the screen surface will cause
the DVD Video mode screen to be displayed.
12
VZ709E
Outline of Button and Touchkey Operation
English
Bluetooth telephone operation
Owner’s manual
(Menu screen)
(Telephone screen)
(10Key screen)
• To make a call, enter the
telephone number using 10-Key
Pad, then touch the [
] (Send)
key.
(Cellular Select screen)
Register your Bluetooth
cellular phone beforehand.
• Touch your desired Telephone
key to select the telephone to be
used.
VZ709E
13
Outline of Button and Touchkey Operation
English
Adjusting the General settings
Owner’s manual
(Menu screen)
(General Settings screen)
(Wall Paper tab screen)
(Display tab screen)
(System tab screen)
14
VZ709E
Outline of Button and Touchkey Operation
English
Adjusting the Audio settings
Owner’s manual
(Menu screen)
(OTHERS tab screen)
(Audio Settings screen)
(BAL/FAD tab screen)
(DZE tab screen)
(TONE tab screen)
VZ709E
15
English
Remote Control Unit
Names of buttons
Owner’s manual
Signal transmitter
Operating range: 30° in all directions
[SUBTITLE]
[AUDIO]
[ANGLE]
[MENU]
[TOP MENU]
[E], [e], [T], [t]
[ENT]
[RETURN]
[SOURCE]
[BAND]
[6]
[–], [+]
[R], [F]
Inserting the Battery
1. Slide the rear cover in the direction of the
arrow, and remove it.
2. Insert the CR2025 battery bundled with the
remote control unit in the directions shown in
the figure, then close the rear cover.
Note:
Using battery improperly can cause it to explode.
Take note of the following points:
• Do not short-circuit, disassemble or heat battery.
• Do not dispose of battery into fire or flames.
• Dispose of spent battery properly.
16
VZ709E
CR2025 battery
Rear cover
Rear side
Remote Control Unit
You can use the remote control unit to control the VZ709E. When the 2Zone function is ON, the controls
work upon the Sub zone only.
[AUDIO] button
• Press to set the Audio language. (in DVD Video
mode)
[VOL –], [VOL +] buttons
• Decreases or increases the volume. (in any
mode; disabled when 2Zone ON)
[SUB TITLE] button
• Press to display subtitles. (in DVD Video mode)
[6] button
• Press to play or pause video and audio media.
(in DVD, USB, and Bluetooth modes; disabled
in USB/Bluetooth modes when 2Zone ON)
• Keep pressing more than 1 second to stop
video playback. (in DVD Video mode)
[ANGLE] button
• Press to set the Angle function of the DVD
video when the Angle mark is displayed. (in
DVD Video mode)
* Available only when the Angle function in the
DVD Setup screen is set to “ON”.
[TOP MENU] button
• Press to display the DVD top menu stored on
the DVD video disc. Some discs are not
displayed the DVD top menu. (in DVD Video
mode)
[MENU] button
• Press to display the DVD menu stored on the
DVD video disc. (in DVD Video mode)
[ENT] button
• Press to fix the selected menu item on the DVD
menu. (in DVD Video mode)
[R], [F] buttons
• Press to select the next lower or higher preset
station. (in TUNER mode; disabled when
2Zone ON)
• Press to select the next lower or higher chapter
number. (in DVD Video mode)
• Press to select the next lower or higher track.
(in CDDA, MP3/WMA/AAC/DivX, USB, and
Bluetooth modes)
• Keep pressing to perform fast backward or fast
forward playback. (in DVD, USB, and Bluetooth
modes)
[E], [e], [T], [t] buttons
• Press to select desired menu item displayed on
the DVD menu. (in DVD Video mode)
[SOURCE] button
• Press to switch the source modes such as
TUNER mode, DVD mode, etc. (in any mode)
* Only DVD, USB, and AUX modes are selectable
when 2Zone ON.
• Keep pressing more than 1 second to turn the
2Zone function ON/OFF. (in any mode)
[RETURN] button
• Press to return to the previous screen while the
DVD menu is being displayed. However, it may
occur that this button operation dose not work
on some discs. (in DVD Video mode)
[BAND] button
• Switches reception bands. (in TUNER mode;
disabled when 2Zone ON)
• Keep pressing more than 1 second to switch
the Home/Travel modes. (in TUNER mode;
disabled when 2Zone ON)
• Press to select the next higher folder. (in MP3/
WMA/AAC/DivX and USB memory modes)
VZ709E
17
Owner’s manual
Note:
• The steering wheel remote control operations work upon the Main zone even when the 2Zone function is ON.
English
Functions of Remote Control Unit Buttons
English
4. BASIC OPERATIONS
Note:
• Be sure to read this chapter referring to the chapter “3. CONTROLS” (page 8).
Owner’s manual
DCP (Detachable Control Panel)
The control panel can be detached to prevent theft. When detaching the control panel, store it in the DCP
case to prevent scratches.
We recommend taking the DCP with you when leaving the car.
Removing the DCP
Attaching the DCP
1. Keep pressing the [SRC] button more than 1
second to turn the Audio OFF.
1. Hook the right side of the DCP to the right side
of the main unit.
2. Settle the left side of the DCP to the main unit.
[SRC] button
Magnet
2. Pull the left side of the DCP toward you, and
remove it.
CAUTION
CAUTION
• This unit uses a magnet to fix the DCP. For
the items that can be affected by
magnetism, such as magnetic cards, be
sure to keep them away from this unit.
• The DCP can easily be damaged by impact.
After removing it be careful not to drop it
nor subject it to strong impact.
• Remote control unit cannot be used when
the DCP is removed.
Note:
• If the DCP is dirty, wipe it off by using a soft dry
cloth.
CAUTION
CAUTION
When the Auto Panel function (see page 62)
is set to “OFF”, be sure to close the liquid
crystal panel for safe before removing the
DCP.
18
VZ709E
CAUTION
CAUTION
Note:
• Start the engine before using this unit.
• Be careful about using this unit for a long time
without running the engine. If you drain the car’s
battery too far, you may not be able to start the
engine and this can reduce the service life of the
battery.
1. Start the engine. The power is supplied to this
unit.
Engine ON
position
Adjusting the Volume
1. Press the [VOL –]/[VOL +] buttons to adjust
the volume.
[VOL –]: Decreases the volume.
[VOL +]: Increases the volume.
• The volume level indicated in the display is
in a range from 0 (min.) to 33 (max.).
CAUTION
CAUTION
While driving, keep the volume level at which
external sounds can be heard.
Opening the Liquid Crystal Panel and Adjusting the
Angle
WARNING
• To prevent the battery from going dead,
operate this unit with the engine running
if possible.
• When the liquid crystal panel is
operating, be careful not to get your hand
or finger caught between the panel and
main unit or the instrument panel of the
car.
• Do not move the liquid crystal panel by
hand.
Standing up the liquid crystal panel
1. Press the [OPEN] button.
The liquid crystal panel comes out and stands
up automatically.
VZ709E
19
Owner’s manual
When the unit is turned on, starting and
stopping the engine with its volume raised to
the maximum level may harm your hearings.
Be careful about adjusting the volume.
2. Press the [SRC] button. The unit
automatically memorizes its last operation
mode and will automatically switch to display
that mode.
3. To turn off the power, press and hold the
[SRC] button for more than 1 second.
• When Auto Panel is set to “ON” or “Close”,
the liquid crystal panel houses after the
power turns off.
●About the CT (Clock Time) display
• The displayed clock data is based on the CT
(clock time) data in the RDS signal, or the GPS
data when the Navigation system is connected.
• When the CT data cannot be received, “--:--”
appears in the display.
English
Turning On and Off the Power
Opening the Liquid Crystal Panel and Adjusting the Angle
English
Owner’s manual
Note:
• If the liquid crystal panel stops in the middle of its
operation, press the [OPEN] button to house the
panel and press the button again to raise it. The
unit will enter the same display mode as the
display was in when last turned off.
3. Repeat touching the [Tilt] key to adjust the
angle of the liquid crystal panel. Every
touching the [Tilt] key tilts the liquid crystal
panel forward or backward.
The adjusted angle is stored in memory.
• Adjustment is possible within the range 70q
to 110q.
• There are 5 adjustable angles available.
MAX 110°
70˚
70˚
Panel calibration function
The liquid crystal panel’s maximum angle of
inclination can be adjusted to match the
installation configuration within the vehicle.
• Perform this with the panel in its housed
position.
1. Keep pressing the [OPEN] button more than 5
seconds.
The electronic beep will be heard.
After the beep sounds twice, the panel will
come out and stand up to the maximum angle.
After completion of the calibration, the panel
will be housed into the unit automatically.
• If the panel does not strike the instrument
panel or other parts of the car during
calibration, the maximum inclination will be
110q.
• If the panel strikes a car part during
calibration within a range of 70q inclination,
the maximum downward inclination will be
70q.
Adjusting the angle of the liquid
crystal panel
The angle of the liquid crystal panel can be
adjusted depending on the mounting angle of the
unit or light coming into the car.
1. Turn the power on. When the liquid crystal
panel is closed, press the [OPEN] button.
2. Press the [MENU] button to display the
following Menu screen:
20
VZ709E
Housing the liquid crystal panel
1. Press the [OPEN] button.
The liquid crystal panel is housed
automatically.
Note:
• When leaving this unit unused for a long period of
time or leaving your car, be sure to house the liquid
crystal panel.
Turning the liquid crystal panel
horizontal (Air conditioner operation
mode)
When the way the liquid crystal panel is mounted
hinders the operation of the air conditioner, the
position of the panel can be turned horizontal
temporarily.
1. Keep pressing the [OPEN] button more than 2
seconds when the liquid crystal panel is open.
A beep sounds and the liquid crystal panel
turns horizontal.
• Press the [OPEN] button again for the panel
to return to the original position.
• The unit can be set so that the panel returns
to the original position after a set time in the
horizontal position (see page 62).
You can turn off all of the AV features.
1. Keep pressing the [SRC] button more than 1
second.
The AV features are turned off.
English
Turning the Audio OFF
Turning the AV features on
Owner’s manual
1. Press the [SRC] button.
The AV features are turned on, and the
system resumes the last status of the AV
features.
Turning the Monitor OFF
You can turn off the monitor screen, and change
it to a black screen.
1. Pressing the [MENU] button to display the
Menu screen.
2. Touch the [Moni Off] key.
The monitor screen is turned off.
Turning the monitor on
1. Touch the monitor screen.
The monitor screen is turned on, and resumes
the last screen.
• You can also turn on the monitor by
pressing any button except for the [o]
(EJECT), [OPEN], and [VOL –]/[VOL +]
buttons.
Setting/Ejecting a Disc
Notes on handling discs
Handling
• New discs may have some roughness around
the edges. If such discs are used, the player
may not work or the sound may skip. Use a
ball-point pen or the like to remove any
roughness from the edge of the disc.
Ball-point pen
Roughness
• Do not use commercially available disc
protection sheets or discs equipped with
stabilizers, etc. These may damage the disc or
cause breakdown of the internal mechanism.
Storage
• Do not expose discs to direct sunlight or any
heat source.
• Do not expose discs to excess humidity or
dust.
• Do not expose discs to direct heat from
heaters.
Cleaning
• Never stick labels on the surface of the disc or
mark the surface with a pencil or pen.
• Never play a disc with any cellophane tape or
other glue on it or with peeling off marks. If you
try to play such a disc, you may not be able to
get it back out of the DVD player or it may
damage the DVD player.
• Do not use discs that have large scratches, are
misshapen, cracked, etc. Use of such discs
may cause misoperation or damage.
• To remove a disc from its storage case, press
down on the center of the case and lift the disc
out, holding it carefully by the edges.
• To remove fingermarks and dust, use a soft
cloth and wipe in a straight line from the center
of the disc to the circumference.
• Do not use any solvents, such as commercially
available cleaners, anti-static spray, or thinner
to clean discs.
• After using special disc cleaner, let the disc dry
off well before playing it.
VZ709E
21
Setting/Ejecting a Disc
English
Setting a disc
On Discs
Owner’s manual
• Exercise a good precaution when loading a
disc with the panel open.
• Never turn off the power and remove the unit
from the car with a disc loaded.
1. Insert a disc into the center of the insertion
slot with the label side facing up.
The disc will automatically be drawn into the
DVD player.
CAUTION
CAUTION
With the liquid crystal panel open, a driver
may not be able to see the disc insertion slot.
For your safety, insert a disc with the screen
closed.
Even when the liquid crystal panel is closed,
however, the recessed disc slot may be
difficult for a driver to see, care is needed
whenever inserting discs.
No/Non
After setting a disc
The system will automatically be switched to the
relevant source media mode according to the
disc, and start playing back the disc.
When a DVD video disc is set:
The system is switched to the DVD Video mode.
See “DVD Video Operations” (page 32).
When an Audio CD is set:
The system is switched to the CDDA mode. See
“Audio CD Operations” (page 39).
When a CD/DVD with MP3/WMA/AAC/DivX
files is set:
The system is switched to the MP3/WMA/AAC
mode or DivX mode according to the Playform
setting. See “MP3/WMA/AAC Operations”
(page 41) or “DivX Operations” (page 44).
Note:
• Never insert foreign objects into the disc insertion
slot.
• If the disc is not inserted easily, there may be
another disc in the mechanism or the unit may
require service.
• 8 cm (single play) discs cannot be used.
CAUTION
For your safety, the driver should not insert
or eject a disc while driving.
Ejecting a disc
1. Press the [o] (EJECT) button to eject the
disc.
The screen changes to the DVD mode
screen, and “EJECT” appears.
• If a disc is left in the ejected position for 15
seconds, the disc is automatically reloaded
(Auto reload).
2. Remove the disc carefully.
Note:
• If you force a disc into the insertion slot before auto
reloading, this can damage the disc.
22
VZ709E
This unit has one USB (Universal Serial Bus) connector which is compatible with USB 1.1 and USB 2.0.
Playable USB media devices
Owner’s manual
This system can control the following USB media
devices connected to the USB connector.
• Apple iPod
• USB memory
English
Connecting/Disconnecting an USB Media Device
About the Apple iPod
iPods can be connected by using the connector
cable supplied with the iPod, but in this case, you
can enjoy its audio sound only. To enjoy video
movies stored in the iPod with video displaying
them on this unit, it is required to use the special
connector cable separately sold.
Note:
• This system will not operate or may operate
improperly with unsupported versions.
• For detailed information on the playable iPod
models, see our home page: www.clarion.com
• For the other limitations, see “iPod Operations”
(page 46).
About the USB memory
This system can play audio files (MP3/WMA/
AAC) stored in an USB memory which is
recognized as “USB Mass Storage Class
device”. You can use your USB memory as an
audio device by simply copying desired audio
files into it.
Note:
• This system will not operate or may operate
improperly with some USB memory.
• Files protected with any DRM can not be played.
• For the other limitations, see “USB Memory
Operations” (page 50).
VZ709E
23
Connecting/Disconnecting an USB Media Device
English
Connecting an USB media
device
Owner’s manual
CAUTION
• For your safety, the driver should not
connect or disconnect an USB media
device.
• Do not start the vehicle’s engine while the
USB media device is connected, since it
may result in loss or damage to data on the
USB media device. Connect the USB media
device to this unit after starting the engine.
• Do not remove the DCP while the USB
media device is connected, since it may
result in loss or damage to data on the USB
media device.
1. Turn on the power of your USB media device,
if required.
2. Confirming the orientation of the connectors,
connect the USB media device to the USB
connector of this unit.
• It may take a long time to recognize the
connected device.
After connecting an USB device
The system will automatically be switched to the
relevant source media mode according to the
USB device connected, and start playback.
When an iPod is connected:
The system is switched to the iPod mode. See
“iPod Operations” (page 46).
When an USB memory is connected:
The system is switched to the USB Memory
mode. See “USB Memory Operations” (page 50).
Note:
• Never insert foreign objects into the USB
connector.
• Always insert the USB media device fully into the
connector. Incomplete connections may cause the
device not to be recognized.
24
VZ709E
Disconnecting an USB media
device
1. Confirm that data transfer is not performed on
the USB media device.
For the method to confirm it, see the operation
manual of your USB media device.
2. Remove the USB media device from the USB
connector.
CAUTION
Be sure to disconnect the USB media device
while the vehicle’s engine is running.
Otherwise, it may result in loss or damage to
data on the USB media device. Do not stop
the engine when the USB media device is
connected.
Note:
• When turning on the ACC power with no USB
media device connected, “MEDIA CHECK” may
be displayed on the screen if the USB mode is
selected.
English
Selecting a Media Source
When the liquid crystal panel is
open
1. Press the [SRC] button to switch the source
mode.
Each time you press the [SRC] button, the
source mode changes in the following order:
TUNER mode ➜ DVD mode ➜ USB mode ➜
Bluetooth mode ➜ AUX mode ➜ TUNER
mode...
1. Press the [SRC] button to display the Source
screen.
Note:
• When 2Zone function is ON, the [SRC] button
works only for the Main zone. To switch the Sub
zone source, specify it from the Source screen, or
use the remote control unit.
2. Touch the desired Source key you wish to
change to.
The system is switched to the corresponding
source media mode.
Available media sources
Source mode
Corresponding source
media mode
Refer to
Description
TUNER mode
TUNER mode
page 27
—
DVD mode
DVD Video mode
page 32
The source media mode differs depending
on the data format of the disc set in the
DVD player.
When no disc is set in the DVD player,
“NO DISC” will be displayed.
CDDA mode
page 39
MP3/WMA/AAC mode
page 41
DivX mode
page 44
iPod mode
page 46
USB Memory mode
page 50
Bluetooth mode
Bluetooth mode
page 51
—
AUX mode
AUX mode
page 58
—
USB mode
The source media mode differs depending
on the type of the USB media device
connected to the USB connector.
When no USB media device is connected,
“NO MEDIA” will be displayed.
Note:
• When the USB mode is selected, video images input from the AUX terminal will be output to the rear monitor.
This is normal.
To select the BT Phone or Navigation mode
You can select the BT Phone or Navigation mode from the Menu screen displayed by pressing the
[MENU] button.
• For details of the BT Phone mode operations, see “Bluetooth Telephone Operations” (page 53).
• For details of the Navigation mode operations, see “Navigation System Operations” (page 57).
VZ709E
25
Owner’s manual
When the liquid crystal panel is
closed
English
2Zone Function
About the 2Zone function
Owner’s manual
The 2Zone function is a function that assigns separate source output to the Main zone (this unit) and
Sub zone (the optional rear monitor) by simultaneously playing two sources in this system. Therefore,
the rear passengers are allowed to enjoy a different video source from the source played on the liquid
crystal panel of this unit.
• The source sounds of the Main zone are output from the speakers of the vehicle side, and those of the
Sub zone are from the optional headphone systems.
• Controlling a source assigned to the Sub zone can be made by using the optional remote control unit.
To control it from this unit, once assign the same source to the Main zone, then control it.
• When a media without video images is played on the Sub zone, a black screen is output to the rear
monitor.
Note:
• When an interrupt of the Bluetooth telephone or the navigation system arises during the 2Zone function is
turned on, the sound of the Main zone is muted, but the sound of the Sub zone is output normally.
When it arises during the 2Zone function is turned off, the audio signals to the 4ch speakers are attenuated,
and the voice from the navigation system is output from the front two speakers.
• You cannot operate the 2Zone function during the interrupt of the Bluetooth telephone or the navigation
system.
• When the same source is assigned for Main and Sub zones, operations in a zone are also applied for another
zone.
Assignable source mode for Main/
Sub zones
●For Main zone
All the source modes can be assigned for the
Front zone.
●For Sub zone
The following source modes can be assigned:
• DVD mode
• USB mode
• AUX mode
Setting the 2Zone function
• The factory default setting is OFF.
1. Press the [SRC] button to display the Source
screen.
2. Touch the [2 Zone] tab to display the 2 Zone
tab screen.
The source keys for the Sub zone are
displayed.
26
VZ709E
3. Touch the desired source key you wish to
assign to the Sub zone.
The 2Zone function is turned on with the
selected source mode assigned to the Sub
zone.
4. Touch the [Back] key to return to the previous
screen.
Note:
• Use the remote control unit to control the source
assigned to the Sub zone. To control it from this
unit, once select the same source mode as
assigned to the Sub zone for the Main zone, and
then control it.
Turning off the 2Zone function
1. Press the [SRC] button to display the Source
screen.
2. Touch and hold the [2Zone Off] key for more
than 1 second.
English
5. SOURCE OPERATIONS
Radio Operations
1. Press the [SRC] button, and touch the
[TUNER] key.
The TUNER mode screen is displayed, and
the system resumes the last status of the
TUNER mode.
2. Touch the [Home] or [Trav] key to select the
Home or Travel mode.
The Home/Travel modes are provided to
manage the preset stations separately in your
home location and in a location during a trip.
3. Touch the [Band] key to select the radio band.
Each time the key is touched, the radio
reception band changes in the following
order:
• In Home mode: FM Home 1 or 2 ➜ AM
Home (MW/LW) ➜ FM Home 1 or 2... (The
last FM band will be selected.)
• In Travel mode: FM Travel ➜ AM Travel
(MW/LW) ➜ FM Travel...
4. Press the [R] or [F] button to tune in the
previous or next preset station.
Seek tuning
There are 2 types of seek tuning: DX SEEK and
LOCAL SEEK.
The DX SEEK can tune in to receivable
broadcast stations, and the LOCAL SEEK can
tune in to only broadcast stations with a good
reception condition.
1. Touch the [Band] key to select the desired
band (FM or AM (MW, LW)).
2. Tune in to a station.
• If “TA” is displayed on the screen, TP
stations are automatically sought.
●DX SEEK
Touch the [R] or [F] key to automatically
seek a station.
When the [F] key is touched, the station is
sought in the direction of higher frequencies; if
the [R] key is touched, the station is sought in
the direction of lower frequencies.
• When the DX Seek tuning starts, “DX SEEK”
appears on the screen.
●LOCAL SEEK
If you keep touching the [R] or [F] key more
than 1 second, the Local Seek tuning is carried
out.
The broadcast stations with good reception
sensitivity are automatically selected.
• When the Local Seek tuning starts, “LO SEEK”
appears on the screen.
Manual tuning
There are 2 ways available: Quick tuning and
step tuning.
When it is in the step tuning mode, the frequency
changes one step at a time. In quick tuning mode,
you can quickly tune the desired frequency.
1. Touch the [Band] key to select the desired
band (FM or AM (MW/LW)).
2. Tune into a station.
Quick tuning:
Touch and hold the [TT] or [tt] key to tune
in a station.
Step tuning:
Touch the [TT] or [tt] key to manually
tune in a station.
Recalling a preset station
There are total of 40 preset positions (8-FM
Home 1, 8-FM Home 2, 8-AM Home, 8-FM
Travel, and 8-AM Travel) to store individual radio
stations in memory.
There are 2 ways available to recall the preset
station.
●Using the [R] or [F] button
1. Touch the [Home] or [Trav] key and touch the
[Band] key to select the desired band.
2. Press the [R] or [F] button to recall the
previous or next stored station.
VZ709E
27
Owner’s manual
Listening to the radio
Radio Operations
English
Owner’s manual
●Using the Preset List screen
1. Touch the [Home] or [Trav] key to select the
Home or Travel mode.
2. Touch the [List] key to display the Preset List
screen.
3. Touch the desired Band key to select the
band.
4. Touch the corresponding Preset key to recall
the stored station.
• Touching and holding the desired Preset
key for more than 2 seconds will store the
current station to the preset memory.
5. Touch the [Back] key to return to the previous
screen.
Manual memory
1. Touch the [Home] or [Trav] key to select the
Home or Travel mode.
2. Touch the [List] key to display the Preset List
screen.
3. Touch the desired Band key to select the
band you wish to store.
4. Tune in the station you wish to store using the
seek tuning, manual tuning, or preset tuning.
5. Touch and hold the desired Preset key you
wish to store the current station for more than
2 seconds.
Auto Store
The Auto Store is a function for storing up to 8
stations that are automatically tuned in
sequentially. If 8 receivable stations cannot be
received, a previously stored station remains
unoverwritten at the memory position.
The Auto Store function works only in the Travel
mode.
1. Touch the [Trav] key to select the Travel
mode.
2. Touch the [List] key.
3. Touch desired Band key to select the band.
4. Touch the [AS] key to start scanning stations.
A beep sounds and the stations with good
reception are stored automatically to the
preset channels.
• “AS” appears during scanning stations. To
stop the scanning, touch the [AS] key again.
28
VZ709E
Scrolling radio text
When the current station broadcasts text data, it
is displayed on the TUNER mode screen. When
the text is longer than the text area, you can
confirm the entire text by scrolling it.
1. Touch the [x] key displayed at the right of the
text area.
The text will scroll once.
About the RDS (Radio Data
System)
This unit has a built in RDS decoder system that
supports broadcast stations transmitting RDS
data. This system can display the name of the
broadcast station being received (PS), and can
automatically switch to the broadcast station with
the best reception as you move long distances
(AF switching). Also, if a traffic announcement or
program type information is broadcast from an
RDS station, no matter what mode you are in, this
broadcast is received. Additionally, if EON
information is received, this information enables
automatic renewal of other preset stations on the
same network and interruption of traffic
announcement and/or chosen program type from
other stations (TP). This function is not available
in some areas.
“AF” : Alternative Frequency
“PS” : Program Service Name
“PTY” : Program Type
“EON”: Enhanced Other Network
“TP” : Traffic Program
• The RDS interrupt does not function during AM
(MW/LW) radio reception.
Radio Operations
English
TA (Traffic Announcement)
function
The AF function switches to a different frequency
on the same network in order to maintain
optimum reception.
When a traffic announcement broadcast starts
during the TA standby mode, the traffic
announcement broadcast is received as top
priority regardless of the function mode, so you
can listen to it. The Traffic Program (TP)
automatic tuning is also available.
Switching ON/OFF the AF function
1. Touch the [Options] key.
2. Touch the [ON] or [OFF] key of the AF item to
turn the function on or off.
• When the AF function is ON, “AF” will be
displayed at the bottom of the screen.
• If the reception of the current broadcast
station deteriorates durably, “AF” indication
will blink, and this unit searches for the
same program on another frequency.
REG (Regional Program)
function
When the REG function is ON, the optimum
regional station can be received. When this
function is OFF, if the regional station area is
switched as you drive, a regional station for that
region is received.
Note:
• This function is disabled when a national station
such as BBC R2 is being received.
• The REG function ON/OFF setting is enabled only
when the AF function is ON.
Switching ON/OFF the REG function
1. Touch the [Options] key.
2. Touch the [ON] or [OFF] key of the REG item
to turn the function on or off.
Manually tuning a regional station in
the same network
Setting TA standby mode
1. Press the [TA] button to set the TA standby
mode.
“TA” will be displayed at the bottom of the
screen, and the system will automatically
search for a TP station (TP SEEK). When an
RDS broadcast station with traffic
announcement program is received, “TP” will
be displayed at the bottom of the screen.
• You can also set this function from the
Options screen by selecting the [ON] or
[OFF] key of the TA item.
Note:
• If no TP station is received, this system continues
the search operation. Performing the above
procedure again makes the “TA” go off, and stops
TP station searching.
●Canceling a Traffic Announcement
broadcast
Press the [TA] button while a Traffic
Announcement broadcast is being received. The
Traffic Announcement broadcast reception is
canceled, and the system goes into the TA
standby mode.
●Canceling TA standby mode
1. When “TA” is displayed on the screen, press
the [TA] button.
“TA” on the screen goes off, and the TA
standby mode is canceled.
Note:
• This function can be used when a regional
broadcast of the same network is received.
• This function is enabled only when the AF function
is ON and the REG function is OFF.
1. Touch the [List] key.
2. Touch the desired Band key to select the
band.
3. Touch your desired Preset key to call out a
regional station.
4. Each time you touch the same Preset key, this
unit switches from a local station to the other
on the same network.
VZ709E
29
Owner’s manual
AF (Alternative Frequency)
function
Radio Operations
English
PTY (Program Type) function
Owner’s manual
This function enables you to listen to a broadcast
of the specified program type when the broadcast
starts, even if the system operates in a mode
other than the TUNER mode.
• Some countries do not yet have PTY
broadcast.
• In the TA standby mode, a TP station has
priority over a PTY broadcast station.
Selecting PTY
1. Touch the [Options] key.
2. Touch the [ON] key of the PTY item to enter
the PTY standby mode.
3. Touch the [PTY Select] key to display the
PTY Select screen.
4. Touch your desired PTY item key to select the
program type.
• The following table shows the factory
default settings stored for the Preset keys:
Preset
number
PTY item
ENGLISH
Contents
News
●Changing the PTY language
1. Touch the [Options] key.
2. Touch the [PTY Language] key to display the
PTY Language screen.
3. Touch the desired Language key you wish to
set.
4. Touch the [Back] key to return to the previous
screen.
PTY seek
1. Touch the [Options] key.
2. Touch the [PTY Select] key to display the
PTY Select screen.
3. Touch the [ITEM] key to display the PTY Item
screen.
4. Touch your desired Program Type key.
5. Touch a Seek key.
If you touch the [F] key, the system seeks
a PTY broadcast moving up the frequencies.
If you touch the [R] key, it seeks moving
down the frequencies.
• If no station with the selected PTY
broadcast can be received, the unit returns
to the previous mode.
• The 29 types of PTY listed below can be
selected.
1
News
2
Info
Information
3
Pop M
Pop music
4
Sport
Sport
ENGLISH
5
Classics
Classics
News
News
6
Easy M
Easy listening
music
Affairs
Current Affairs
Info
Information
7
Light M
Light classical
music
Sport
Sport
8
Weather
Weather
Educate
Education
Drama
Drama
5. Touch the [Back] key to return to the previous
screen.
●Canceling PTY standby mode
1. Touch the [Options] key.
2. Touch the [OFF] key of the PTY item.
“PTY” goes off, and the PTY standby mode is
canceled.
●Canceling PTY interrupt broadcast
1. Press the [TA] button during receiving the
PTY interrupt broadcast. The PTY interrupt is
canceled, and the system returns to PTY
standby mode.
• You can also cancel the PTY interrupt
broadcast by touching the [Cancel] key
displayed on the screen.
30
VZ709E
PTY item
Contents
Culture
Culture
Science
Science
Varied
Varied
Pop M
Pop Music
Rock M
Rock Music
Easy M
Easy Listening Music
Light M
Light Classical Music
Classics
Serious Classical
Music
Other M
Other Music
Weather
Weather
Finance
Finance
Children
Children’s Programs
Radio Operations
Social Affairs
Religion
Religion
Phone in
Phone In
Travel
Leisure
Leisure
Jazz
Jazz Music
Country
Country Music
Nation M
National Music
Oldies
Oldies Music
Folk M
Folk Music
Document
Documentary
Owner’s manual
Travel
English
Social
Emergency broadcast
If an emergency broadcast is received, all the
function mode operations are stopped. “Alarm”
appears on the screen and the emergency
broadcast can be heard.
●Canceling an emergency broadcast
1. Press the [TA] button during receiving the
emergency broadcast. The emergency
broadcast is canceled, and the system returns
to the PTY standby mode.
• You can also cancel the emergency
broadcast by touching the [Cancel] key
displayed on the screen.
Volume setting of TA,
emergency broadcast (Alarm)
and PTY
The volume for TA, Alarm and PTY interrupts can
be set during TA, Alarm or PTY interrupt.
• The factory default setting is “15”.
1. Use the [VOL +] and [VOL –] buttons to set
the volume to the desired level (00 to 33)
during a TA, Alarm or PTY interrupt.
• When the TA, Alarm, or PTY interrupt ends,
the volume returns to the level before the
interrupt.
VZ709E
31
English
DVD Video Operations
Selecting the DVD Video mode
Owner’s manual
1. Set a DVD video disc to the DVD player.
The system will automatically read the disc
data, change to the DVD mode (DVD Video
mode), and start playback after a while.
See also “Setting/Ejecting a Disc” (page 21).
Changing the DVD System
Settings
Note:
• If the Setup operation is performed in the middle of
DVD video play, the disc will restart from
beginning.
Displaying the DVD Setup screen
1. Touch the screen to display the DVD Video
mode screen.
2. Touch the [Options] key to display the
Options menu.
3. Touch the [Set up] key to display the DVD
Setup screen.
WARNING
• Some videos may be recorded at a higher
volume level than desired. Increase the
volume gradually from the minimal
setting after the video has started.
• For your safety, the driver should not
watch the video or operate the controls
while driving. Please note that watching
and operating the video while driving are
prohibited by law in some countries.
Note:
• For your safety, this system has a safety function
which turns off the picture when the car is moving,
so only the audio can be heard. The picture can
only be watched when the car is stopped and the
parking brake is applied.
• If “AUDIO ONLY” appears on the screen just after
turning on the ACC power of the car, release the
parking brake while confirming safety, and then
engage the parking brake again.
●When a DVD video disc is already set
1. Press the [SRC] button to display the Source
screen.
2. Touch the [DVD] key to select the DVD Video
mode.
The system changes to the DVD mode (DVD
Video mode), and starts playback from the
previous position.
32
VZ709E
• Touch the [C] key to display the next page.
• Touch the [c] key to return to the previous
page.
4. Perform setting for the desired setting items.
See the following sections for detail.
• In the following sections, only the details of
settings are described, the procedures to
select items are skipped.
5. Touch the [Back] key.
DVD Video Operations
• The factory default setting is “English”.
4-1. Touch the [Wide], [PS], or [LB] key of the TV
Display item to change the screen size to
“Wide”, “Pan Scan” or “Letter Box”.
●When watching through a wide type of the
rear monitor (16:9)
Wide:
4-1. Touch the [x] key of the Menu Language
item.
4-2. Touch the desired Language key you wish
to set.
4-3. Touch the [Back] key.
Setting up the audio language
• The factory default setting is “English”.
4-1. Touch the [x] key of the Audio Language
item.
4-2. Touch the desired Language key you wish
to set.
●When watching through a conventional
type of the rear monitor (4:3)
Pan Scan:
The leftmost and rightmost areas of the screen
are cut off.
4-3. Touch the [Back] key.
Setting up the subtitle language
• The factory default setting is “English”.
4-1. Touch the [x] key of the Subtitle Language
item.
4-2. Touch the desired Language key you wish
to set.
• To turn off the subtitle, select the [Off] key.
This function allows displaying the important
part of image fully on the screen. In some
cases, image is displayed while being panned
(scrolled).
Letter Box:
A black zone is created in the top and bottom
areas of the screen.
This method displays Cinema Scope and Vista
Vision images without cutting them off by
creating a black zone on the top and bottom
gaps.
Setting up the angle mark display
You can set up so that the angle mark appears on
scenes where the angles can be switched.
• The factory default setting is “OFF”.
4-3. Touch the [Back] key.
Setting up the password for setting
up of the parental level
• The factory default setting is “0000”.
4-1. Touch the [x] key of the Password item.
4-2. Touch the ten-key (0 to 9) to input a 4-digit
password.
• Input the old password, and touch the
[ENT] key.
Input “4356” to reset password.
• Input a new password, and touch the
[ENT] key.
• Input the same new password again, and
touch the [ENT] key.
Note:
• When a disc with view restrictions is inserted, you
will be prompted to input a password. The disc will
not be viewable until the correct password is
entered.
4-1. Touch the [ON] or [OFF] key of the Angle
item to turn the Angle function ON or OFF.
VZ709E
33
Owner’s manual
Setting up the disc menu language
Set up the screen size according to the optional
rear monitor which is connected to this unit.
• The factory default setting is “Wide”.
English
Setting up the screen size
DVD Video Operations
English
Owner’s manual
Setting up the country code
LIECHTENSTEIN
7673
Set up the country number for setting up of the
parental level.
• The factory default setting is “7166” (U.K.).
LUXEMBOURG
7685
MACEDONIA, THE FORMER
YUGOSLAV REPUBLIC OF
7775
4-1. Touch the [x] key of the Country Code item.
MALTA
7784
MONACO
7767
4-3. Touch the [ENT] key.
NETHERLANDS
7876
Country code list:
(NETHERLANDS ANTILLES)
6578
NORWAY
7879
4-2. Touch the ten-key (0 to 9) to input a 4-digit
country code (see the following table).
Country
Input code
ALBANIA
6576
OMAN
7977
ANDORRA
6568
POLAND
8076
6584
PORTUGAL
8084
BAHRAIN
6672
QATAR
8165
BELGIUM
6669
ROMANIA
8279
BOSNIA AND
HERZEGOWINA
6665
SAN MARINO
8377
SAUDI ARABIA
8365
BULGARIA
6671
SLOVAKIA (Slovak Republic)
8375
CROATIA (local name:
Hrvatska)
7282
SLOVENIA
8373
CYPRUS
6789
CZECH REPUBLIC
6790
DENMARK
6875
EGYPT
6971
FINLAND
7073
FRANCE
7082
(FRANCE,METROPOLITAN)
7088
AUSTRIA
GERMANY
6869
GREECE
7182
HUNGARY
7285
ICELAND
7383
IRAN (ISLAMIC REPUBLIC
OF)
7382
IRAQ
7381
IRELAND
7369
ISRAEL
7376
ITALY
7384
JAPAN
7480
JORDAN
7479
KUWAIT
7587
LEBANON
7666
LESOTHO
7683
34
VZ709E
SOUTH AFRICA
9065
SPAIN
6983
SWAZILAND
8390
SWEDEN
8369
SWITZERLAND
6772
SYRIAN ARAB REPUBLIC
8389
TURKEY
8482
UNITED ARAB EMIRATES
6569
UNITED KINGDOM
7166
Vatican City State
8665
YEMEN
8969
YUGOSLAVIA
8985
FAROE ISLANDS
7079
GIBRALTAR
7173
GREENLAND
7176
SVALBARD AND JAN
MAYEN ISLANDS
8374
DVD Video Operations
4-1. Touch the [[] or []] key of the Parental Level
item.
The Password input screen is displayed.
4-2. Touch the ten-key (0 to 9) to input a 4-digit
password, and touch the [ENT] key.
• The factory default setting of the
password is “0000”.
4-3. Touch the [[] or []] key to select level “1” to
“8”, or “No Parental”.
The relationship between DVD video
category codes and parental level are
shown in the table below. Use this table
when setting the parental level.
LEVEL7
NC-17
(NO ONE 17 AND UNDER
ADMITTED)
LEVEL6
R
(RESTRICTED)
LEVEL4
PG-13
(PARENTS STRONGLY
CAUTIONED)
LEVEL3
PG
(PARENTAL GUIDANCE
SUGGESTED)
LEVEL1
G
(GENERAL AUDIENCES)
• The contents that the parental level restricts
vary with the country code.
Operating a DVD video
Watching a DVD Video
After disc loading, the play mode is automatically
engaged.
• When playback is not started, touch the [p]
key.
• Operations may differ depending on the story
of the disc.
Showing the DVD Video mode
screen
The DVD Video mode screen is used to control
the playback mode from the screen.
1. Touch the screen.
The DVD Video mode screen is displayed.
If you do not touch the screen for 7 seconds,
the display will return to the playback screen.
Selecting the screen size
You can change the screen size to suit to the
playback film.
• The factory default setting is “F.Wide”.
1. Touch the screen to display the DVD Video
mode screen.
2. Repeat touching the [Wide/F.Wide/Cinema/
Normal] key until your desired screen size is
selected.
• This key shows the current screen size setting.
[Wide]:
The image is expanded in the same way as
the [F.Wide] setting, but the width will become
narrower. Depending on the image data,
black areas may be displayed at the both
sides of the screen.
[F.Wide]:
The image is expanded so that the rectangle
of the image fits to the screen (16:9). The
aspect ratio of the image may be changed.
[Cinema]:
The image is expanded so that the top and
bottom edges of the image fit to the screen.
Suitable for letterbox-format images. Subtitles
of non-letterboxed images may be cut off in
this mode.
[Normal]:
The image is expanded so that the top and
bottom edges of the image fit to the screen,
and that the aspect ratio of the image
becomes 4:3. The aspect ratio of the image
may be changed.
3. Touch the [Hide] key to return to the playback
screen.
VZ709E
35
Owner’s manual
You can change the level of parental lock
(audiovisual restriction).
This function allows cutting scenes that are
unfavorable for children or replacing them
automatically with other scenes prepared in
advance. For example, by replacing scenes of
radical violence or portrayals of sex with safe
scenes, you can make a trouble-free story as if it
were so from the beginning.
• The factory default setting is “8”.
●About the volume adjustment when playing
DVD Video discs
This system has the independent volume data for
playing DVD Video discs. The volume setting
during DVD playback does not affect the volume
of the other modes, and the volume setting in the
other modes does not affect the DVD playback.
●When the DVD menu is displayed
For general DVD Video discs, the DVD menu
may appear.
After the DVD menu is displayed, select an item
in the operations described as follows.
English
Setting up the parental level
DVD Video Operations
English
DVD menu operations
Owner’s manual
●Showing the DVD menu
1. Showing the DVD Video mode screen, touch
the [Menu] or [Top Menu] key during
playback.
The DVD menu appears.
• The displayed contents for each key differ
depending on the DVD software.
• An example shown below is the DVD menu
display:
●Operating the DVD menu
You can operate the menu items by displaying
the Key Pad panel.
1. Touch the screen to display the DVD Video
mode screen, and then touch the [Key] key.
The Cursor-Key Pad panel is displayed on the
screen.
• Touching the [Num] key changes the panel
to the Numeric-Key Pad.
2. Select the desired menu item using either the
Cursor-Key or the Nummeric-Key according
to the menu contents.
3. Touch the [ENT] key to specify the selected
menu item.
4. Touch the [Hide] key to hide the Key Pad
panel.
●Switching Key Pad position
When the menu items become difficult to view by
the Key Pad buttons, you can move the Key Pad
panel to the other side of the screen.
Key Pad
Key Pad
Stopping playback
1. Showing the DVD Video mode screen, touch
and hold the [p] key for more than 1
second during playback.
Playback is stopped.
2. To resume playback, touch the [p] key.
Playback resumes from the scene where
playback is stopped.
Pausing playback
1. Showing the DVD Video mode screen, touch
the [p] key during playback.
Playback pauses.
2. To resume playback, touch the [p] key
again.
Playback resumes.
36
VZ709E
DVD Video Operations
“Chapter” means a small segment to divide the
“Title” (film) which is recorded on the disc.
1. Press the [R] or [F] button during
playback.
Chapters are skipped as many as the times
pressing the button, and playback starts.
Fast forward and fast backward
1. Keep pressing the [R] or [F] button
during playback.
[F] button: Fast forward
[R] button: Fast backward
The playback speed becomes 4-times faster
at first and then 16-times faster 3 seconds
later.
Releasing the button resumes the normal
speed playback.
• No audio is reproduced during fast forward
and fast backward operation.
• The fast forward and fast backward speed
may differ depending on the disc.
• You can also use the [R] and [F] keys
instead of the [R] and [F] buttons.
Current
location
Chapter
down
Chapter
Chapter
up
• Pressing the [F] button starts playback
from the beginning of the next chapter.
• Pressing the [R] button starts playback
from the beginning of the current chapter.
When pressing this button again within
about 4 seconds, playback starts from the
beginning of the previous chapter.
• You can also use the [R] and [F] keys
instead of the [R] and [F] buttons.
Searching with a chapter/title
number
You can locate the beginning of a scene using
the chapter numbers or title numbers recorded
on the DVD video disc.
• “Chapter” means a small segment to divide the
“Title” (film) which is recorded on the disc.
1. Showing the DVD Video mode screen, touch
the [Options] key.
2. Touch the [Direct] key.
The Key Pad screen appears.
• You can select the next title by touching the
[Title] key.
3. Input the chapter number that you want to
play back using the [0] to [9] key.
4. Touch the [ENT] key.
Playback starts from the scene of the input
chapter number of the selected title.
• If the input chapter number does not exist or
searching with a chapter number is not
allowed, the screen image will not change.
VZ709E
37
Owner’s manual
Skipping chapters (searching)
1. Showing the DVD Video mode screen, touch
the [p] key during playback to pause
playback.
2. Touch and hold the [F] key.
While touching the key, slow playback
continues at 1/3 speed.
Releasing the key resumes the normal
playback.
• Slow playback cannot be performed in the
backward direction. In addition, audio
cannot be reproduced during slow
playback.
• You can also use the [F] button instead
of the [F] key.
English
Slow playback
DVD Video Operations
English
Repeat playback
Owner’s manual
This operation plays back the current title or
chapter repeatedly.
1. Showing the DVD Video mode screen, touch
the [Options] key.
2. Touch the [Title] or [Chapter] key of the
Repeat item, then touch the [Back] key.
The “T.RPT” or “C.RPT” will be displayed.
3. Perform the same operation to turn off the
repeat playback.
Switching among languages
On discs in which two or more audios or audio
languages have been recorded, you can switch
among the audio languages during playback.
1. Showing the DVD Video mode screen, touch
the [Options] key.
2. Touch the [Audio] key during playback.
Each time you touch the key, you can switch
among audio languages.
• Depending on the disc, up to 8 audios may
be recorded. For details, see the mark of the
disc ( 8 : Indicates that 8 audios have
been recorded).
• Depending on the disc, switching may be
completely impossible or impossible on
some scenes.
• It may take time to switch among audios.
• When the power is turned on and the disc is
changed to a new one, the language set as
the factory default is selected. If that
language has not been recorded, the
language is specified on the disc.
3. Touch the [Back] key to return to the previous
screen.
Switching subtitles
On DVD discs in which two or more subtitle
languages have been recorded, you can switch
among the subtitle languages during playback.
1. Showing the DVD Video mode screen, touch
the [Options] key.
2. Touch the [Subtitle] key during playback.
The Subtitle Language screen appears.
3. Touch the Language key you wish to display.
• Depending on the disc, up to 32 kinds of
subtitles may be recorded. For details, see
the mark of the disc ( 8 : Indicates that 8
kinds of subtitles have been recorded).
• To turn of subtitles, select “OFF”.
• Depending on the disc, switching may be
completely impossible or impossible on
some scenes.
• It may take time to switch among subtitles.
38
VZ709E
4. Touch the [Back] key to return to the previous
screen.
Switching angles
On DVD discs in which video images have been
recorded in two or more angles, you can switch
among the angles during playback.
• This operation can be performed when the
“Setting up the angle mark display” function
(see page 33) is set to “ON”.
1. Showing the DVD Video mode screen, touch
the [Angle] key during playback.
Each time you touch the key, you can switch
among angles.
• Depending on the disc, up to 9 angles may
be recorded. For details, see the mark of the
disc (
: Indicates multi-angle).
• Depending on the disc, angles may switch
smoothly or switch with a momentary still
image.
• Depending on the disc, switching may be
completely impossible or impossible on
some scenes.
• It may take time to switch among angles.
• Depending on the disc, scenes recorded in
two or more angles may be played back.
• When the power is turned on and the disc is
changed to a new one, the language set at
the time of factory shipment is selected. If
that language has not been recorded, the
language is specified on the disc.
Displaying/hiding the playback
status
1. Showing the DVD Video mode screen, touch
the [Options] key.
2. Touch the [ON] or [OFF] key of the P.Time
item during playback.
3. Touch the [Back] key to return to the previous
screen.
Playback status is displayed on the screen.
Title number
Chapter number
Playback time
T01
C0 0 1
00 : 00 : 19
English
Audio CD Operations
This system is a CD TEXT compatible model, and supports the display of the DISC TITLE, TRACK
TITLE, and TRACK ARTIST of the CD TEXT.
Selecting the CDDA mode
1. Set an audio CD to the DVD player.
The system will automatically read the disc
data, change to the DVD mode (CDDA
mode), and start playback after a while.
See also “Setting/Ejecting a Disc” (page 21).
Operating an audio CD
Listening to an audio CD
After disc loading, the play mode is automatically
engaged.
• When playback is not started, touch the [p]
key.
Pausing playback
1. Touch the [p] key during playback.
Playback pauses.
2. To resume playback, touch the [p] key.
Playback resumes.
Skipping a track (searching)
WARNING
• Some CDs may be recorded at a higher
volume level than desired. Increase the
volume gradually from the minimal
setting after playback has started.
• For your safety, the driver should not
operate the controls while driving.
●When an audio CD is already set
1. Press the [SRC] button to display the Source
screen.
2. Touch the [DVD] key to select the CDDA
mode.
The system changes to the DVD mode
(CDDA mode), and starts playback from the
previous position.
1. Press the [R] or [F] button during
playback.
Tracks are skipped, as many as the times the
button is pressed, and playback starts.
• Pressing the [F] button starts playback
from the beginning of the next track.
• Pressing the [R] button starts playback
from the beginning of the current track.
When this button is pressed again within
about 2 seconds, playback starts from the
beginning of the previous track.
• You can also use the [R] and [F] keys
instead of the [R] and [F] buttons.
Fast forward and fast backward
1. Press and hold the [R] or [F] button
during playback.
The playback speed becomes 4-time faster
first and then 16-time faster 3 seconds later.
Releasing the button resumes the normal
speed playback.
• You can also use the [R] and [F] keys
instead of the [R] and [F] buttons.
VZ709E
39
Owner’s manual
Note:
• This unit supports only CD TEXT in English. Also, some character data may not be reproduced properly on
the display.
Audio CD Operations
English
Other various play functions
Owner’s manual
1. Touch the [Options] key.
2. Touch the [Track] key of the function you
want to play.
Track repeat playback:
Touch the [Track] key of the Repeat item.
• This operation plays back the current track
repeatedly.
• “T.RPT” is displayed on the screen.
Track random playback:
Touch the [Track] key of the Random item.
• This operation plays back all tracks on the
disc in no particular order.
• “T.RDM” is displayed on the screen.
3. To cancel the play, touch the [Track] key of
the function to cancel.
4. Touch the [Back] key to return to the previous
screen.
Scrolling track titles
When a title or name displayed on the screen is
longer than the text area, you can confirm the
entire text by scrolling it.
1. Displaying the text you wish to scroll, touch
the [x] key displayed at the right of the text
area.
The text will scroll once.
40
VZ709E
This system can playback MP3/WMA/AAC files recorded on a disc.
About the MP3/WMA/AAC files
MP3, WMA, and AAC are the audio file formats
which have penetrated into PC users and
become a standard format.
MP3 is an audio compression method and
classified into audio layer 3 of MPEG standards.
WMA (Windows Media Audio) is an audio
compression method developed by Microsoft
Corporation.
AAC (Advanced Audio Coding) is a newer audio
compression method developed for used with
video compression standards MPEG-2 and
MPEG-4, and has been adopted as the standard
audio format of the iPod and iTunes by Apple Inc.
These features compress the original audio data
to about 10 percent of its initial size with a high
sound quality. This means that about 10 audio
CDs can be recorded on a CD-R/RW disc to
allow a long listening time without having to
change CDs.
Displaying MP3/WMA/AAC Tag titles
Tag information (track title, artist name, and
album title) can be displayed for an MP3/WMA/
AAC file containing the Tag information.
This system supports the ID3 TAG version 1.x/
2.x and WMA-TAG.
Note:
• Tag information entered with 2-byte characters
may not be displayed properly on the display.
• The ID3 version 2.x tag format is not completely
supported. This system can display information up
to 60 bytes, and ignores the rest.
• Album titles of WMA-TAG may not be displayed
properly.
●General precautions
• Files other than MP3/WMA/AAC format cannot
be played. In addition, some files may not be
played because of the encoding settings.
When a file cannot be played, the next file is
played instead.
• Some noise may occur depending on the type
of encoder software used to encode the data.
• You can apply the VBR (Variable Bit Rate)
format when encoding. In this case, the
displayed play time may be slightly different
from the actual play time.
• Files that the DRM (Digital Rights
Management) function is set cannot be played.
●For MP3 files
• Set the Sampling Frequency to:
• MPEG1 Layer3: 32, 44.1, or 48 kHz
• MPEG2 Layer3: 16, 22.05, or 24 kHz
• MPEG2.5 Layer3: 8, 11.025, or 12 kHz
• Set the Bit Rate to:
• MPEG1 Layer3: 32 to 320 kbps (VBR)
• MPEG2 Layer3: 8 to 160 kbps (VBR)
• MPEG2.5 Layer3: 8 to 160 kbps (VBR)
• Add a file extension “.MP3” or “.mp3” using
single byte characters.
●For WMA files
• Set the Sampling Frequency to within ranges
from 22.05 to 44.1 kHz.
• Set the Bit Rate to 48, 64, 80, 96, 128, 160, or
192 kbps.
• Add a file extension “.WMA” or “.wma” using
single byte characters.
●For AAC files
• This system supports only the MPEG4 Audio
files encoded by the iTunes.
• Set the Sampling Frequency to 44.1 or 48 kHz.
• Set the Bit Rate to within ranges from 16 to 320
kbps (VBR).
• Add a file extension “.M4A” or “.m4a” using
single byte characters.
VZ709E
41
Owner’s manual
What is MP3/WMA/AAC?
Precautions on the MP3/WMA/AAC
files
English
MP3/WMA/AAC Operations
MP3/WMA/AAC Operations
English
Precautions when preparing a disc
Note:
• For details of the DivX file mentioned below, see
“DivX Operations” (page 44).
Owner’s manual
●Logical format (File system)
The following writing formats are available when
writing MP3/WMA/AAC/DivX files on a disc:
• For CD-R/RW: ISO9660 level 1/level 2,
Romeo, Joliet, or Apple ISO (without including
expansion format)
• For DVD±R/RW: UDF (Universal Disk Format)
●Folder structure
• The folder hierarchy must be within 8
hierarchical levels. Otherwise, playback will be
impossible.
• You can store the MP3 files, WMA files, and
AAC files together in a disc or folder.
• You can also store the MP3/WMA/AAC files
and DivX files together in a disc or folder. In
such a case, you can select whether the disc is
regarded as an MP3/WMA/AAC disc or as a
DivX disc. see “Setting the Playform of discs
recorded with DivX files” (page 43).
●Number of files or folders
• The maximum allowable number of folders is
255 (including root directory).
• The maximum allowable number of files in a
disc is 999.
• The maximum allowable number of files in a
folder is 255.
●Folder representation in the folder list
• Only folders containing MP3/WMA/AAC files or
DivX files (1 to 4 in illustration) are displayed
on the list. Folders containing no MP3/WMA/
AAC/DivX file are not displayed.
• Folder hierarchy (1 to 4 in illustration) is
ignored, and unified into one level.
• Folders are arranged in the order of the folder
creation.
1
2
1
3
1. Set a disc which the MP3/WMA/AAC files are
recorded to the DVD player.
The system will automatically read the disc
data, change to the DVD mode (MP3/WMA/
AAC mode), and start playback after a while.
See also “Setting/Ejecting a Disc” (page 21).
WARNING
• Audio files may be recorded at a higher
volume level than desired. Increase the
volume gradually from the minimal
setting after playback has started.
• For your safety, the driver should not
operate the controls while driving.
Note:
• Note that the system enters to the DivX mode
when setting a disc with DivX files if the Playform
function has been set to “Video” (see page 43).
●When a disc is already set
1. Press the [SRC] button to display the Source
screen.
2. Touch the [DVD] key to select the MP3/WMA/
AAC mode.
The system changes to the DVD mode (MP3/
WMA/AAC mode), and starts playback from
the previous position.
Operating MP3/WMA/AAC
playback
4
2
4
Selecting the MP3/WMA/AAC
mode
3
Note:
• The same operations listed below are also used in
the USB Memory mode.
Listening to MP3/WMA/AAC files
After disc loading, the play mode is automatically
engaged.
• When playback is not started, touch the [p]
key.
42
VZ709E
MP3/WMA/AAC Operations
1. Touch the [Options] key.
2. Touch a touch key of the function you want to
play.
Folder repeat playback:
Touch the [Folder] key of the Repeat item.
• This operation plays back tracks in the
current folder repeatedly.
• “F.RPT” is displayed on the screen.
Track repeat playback:
Touch the [Track] key of the Repeat item.
• This operation plays back the current track
repeatedly.
• “T.RPT” is displayed on the screen.
Folder random playback:
Touch the [Folder] key of the Random item.
• This operation plays the tracks in the
current folder in a random order.
• “F.RDM” is displayed on the screen.
Track random playback:
Touch the [Track] key of the Random item.
• This operation plays back tracks recorded
in the disc in no particular order.
• “T.RDM” is displayed on the screen.
3. To cancel the play, touch the same touch key
of the function to cancel.
4. Touch the [Back] key to return to the previous
screen.
Skipping a track (searching)
1. Press the [R] or [F] button during
playback.
Tracks are skipped, as many as the times the
button is pressed, and playback starts.
• Pressing the [F] button starts playback
from the beginning of the next track.
• Pressing the [R] button starts playback
from the beginning of the current track.
When this button is pressed again within
about 2 seconds, playback starts from the
beginning of the previous track.
• You can also use the [R] and [F] keys
instead of the [R] and [F] buttons.
• These functions perform in the current
folder only.
Fast forward and fast backward
1. Press and hold the [R] or [F] button
during playback.
The playback speed becomes 4-time faster
first and then 16-time faster 3 seconds later.
Releasing the button resumes the normal
speed playback.
• You can also use the [R] and [F] keys
instead of the [R] and [F] buttons.
Skipping the current folder
1. Touch a FOLDER key during playback.
The tracks of the current folder are skipped
and playback starts from the first track of the
next or previous folder.
Selecting a folder/track from the list
screen
1. Touch the [List] key.
The Folder List screen is displayed.
2. When the desired folder is not displayed,
touch the [c] or [C] key to scroll the list.
3. Touch the desired Folder key.
The Track List screen appears.
4. Touch the [c] or [C] key to scroll the list, and
touch the desired Track key.
The corresponding track is started playback.
5. Touch the [Back] key.
Scrolling track titles
When a title or name displayed on the screen is
longer than the text area, you can confirm the
entire text by scrolling it.
1. Displaying the text you wish to scroll, touch the
[x] key displayed at the right of the text area.
The text will scroll once.
Setting the Playform of discs
recorded with DivX files
MP3/WMA/AAC files can be stored together with
DivX files in a disc or folder. You can select
whether such discs are regarded as MP3/WMA/
AAC discs or as DivX discs.
1. Touch the [Options] key.
2. Touch the [Audio] or [Video] key of the
Playform item to specify the setting.
[Audio]:
Discs are regarded as MP3/WMA/AAC discs.
[Video]:
Discs are regarded as DivX discs.
3. Touch the [Back] key.
Note:
• This setting is disabled when a Mixed Mode
CD, which contains both data track and audio
tracks, is set in the DVD player.
VZ709E
43
Owner’s manual
Other various play functions
1. Touch the [p] key during playback.
Playback pauses.
2. To resume playback, touch the [p] key.
Playback resumes.
English
Pausing playback
English
DivX Operations
This system can playback DivX movie files recorded on a disc.
• Official DivX® Certified product
• Plays all versions of DivX® video (including DivX® 6) with standard playback of DivX® media files.
Owner’s manual
About the DivX file
What is DivX?
DivX is a popular media technology created by
DivX, Inc. DivX media files contain highly
compressed video with high visual quality that
maintains a relatively small file size. DivX files
can also include advanced media features like
menus, subtitles, and alternate audio tracks.
Many DivX media files are available for download
online, and you can create your own using your
personal content and easy-to-use tools from
DivX.com.
Selecting the DivX mode
1. Set a disc which the DivX files are recorded to
the DVD player.
The system will automatically read the disc
data, change to the DVD mode (DivX mode),
and start playback after a while.
See also “Setting/Ejecting a Disc” (page 21).
Precautions on the DivX file
• This system can play DivX version 4.x, 5.x, and
6.x files. DivX Ultra is not supported.
• Files other than DivX format cannot be played.
In addition, some files may not be played
because of the encoding format. When a file
cannot be played, the next file is played
instead.
• DivX VOD (Video-on Demand files) that have
authorization data can also be played. These
files must be authorized on your PC
beforehand using the DivX Registration Code
displayed on the System tab screen under the
General Setttings screen (see page 63).
• Set the Frame Size to 640 x 480 or 320 x 240
pixels.
• Set the Frame Rate to 30 or 15 fps.
• Add a file extension “.AVI”, “.avi”, “.DIVX”, or
“.divx” using single byte characters.
Precautions when preparing a disc
Note:
• The limitations on preparing a disc are same as
those in the MP3/WMA/AAC modes. See
“Precautions when preparing a disc” (page 42).
WARNING
• Some movie files may be recorded at a
higher volume level than desired.
Increase the volume gradually from the
minimal setting after the movie has
started.
• For your safety, the driver should not
watch the movie or operate the controls
while driving. Please note that watching
and operating the movie while driving are
prohibited by law in some countries.
Note:
• For your safety, this system has a safety function
which turns off the picture when the car is moving,
so only the audio can be heard. The picture can
only be watched when the car is stopped and the
parking brake is applied.
• If “AUDIO ONLY” appears on the screen just after
turning on the ACC power of the car, release the
parking brake while confirming safety, and then
engage the parking brake again.
• You can store DivX files and the MP3/WMA/AAC files
together in a disc or folder. In such a case, you can
select whether the disc is regarded as a DivX disc or
as an MP3/WMA/AAC disc. See “Setting the Playform
of discs recorded with audio files” (page 45).
●When a disc is already set
1. Press the [SRC] button to display the Source
screen.
2. Touch the [DVD] key to select the DivX mode.
The system changes to the DVD mode (DivX
mode), and starts playback from the previous
position.
44
VZ709E
DivX Operations
Watching DivX movies
After disc loading, the play mode is automatically
engaged.
• When playback is not started, touch the [p]
key.
●To play a file with Authorization data
When a file with Authorization data is played, a
message is displayed on the screen. Confirm the
message displayed, and touch the [Done] or
[Yes] key to play the movie.
Showing the DivX mode screen
The DivX mode screen is used to control the
playback mode from the screen.
1. Touch the screen.
The DivX mode screen is displayed.
If you do not touch the screen for 7 seconds,
the display will return to the playback screen.
• You can hide the DivX mode screen by
touching the [Hide] key.
Selecting the screen size
You can change the screen size to suit to the
playback film.
• The factory default setting is “F.Wide”.
1. Touch the screen to display the DivX mode
screen.
2. Repeat touching the [Wide/F.Wide/Cinema/
Normal] key until your desired screen size is
selected.
• This key shows the current screen size setting.
[Wide]:
The image is expanded in the same way as
the [F.Wide] setting, but the width will become
narrower. Depending on the image data,
black areas may be displayed at the both
sides of the screen.
[F.Wide]:
The image is expanded so that the rectangle
of the image fits to the screen (16:9). The
aspect ratio of the image may be changed.
[Cinema]:
The image is expanded so that the top and
bottom edges of the image fit to the screen.
Suitable for letterbox-format images. Subtitles
of non-letterboxed images may be cut off in
this mode.
Searching with a folder/track
number
You can specify a file to play using the folder
number or track number.
1. Showing the DivX screen, touch the
[Options] key.
2. Touch the [Direct] key.
The Key Pad screen appears with the folder
number input mode.
3. Input the folder/track number that you want to
play back using the [0] to [9] key.
• Touching the [Track] key turns the Key Pad
to the track number input mode.
4. Touch the [ENT] key.
The system starts playback of the file
specified with the input folder/track numbers.
• If the input folder/track number does not
exist or searching with a folder/track
number is not allowed, the screen image will
not change.
Setting the Playform of discs
recorded with audio files
DivX files can be stored together with MP3/WMA/
AAC files in a disc or folder. You can select
whether such discs are regarded as DivX discs or
as MP3/WMA/AAC discs.
1. Showing the DivX screen, touch the
[Options] key.
2. Touch the [Audio] or [Video] key of the
Playform item to specify the setting.
[Audio]:
Discs are regarded as MP3/WMA/AAC discs.
[Video]:
Discs are regarded as DivX discs.
3. Touch the [Back] key.
Note:
• This setting is disabled when a Mixed Mode CD,
which contains both data track and audio tracks, is
set in the DVD player.
VZ709E
45
Owner’s manual
Note:
• The most operations in the DivX mode are same
as those in the MP3/WMA/AAC modes. See also
“Operating MP3/WMA/AAC playback” (page 42).
• The random plays cannot be specified in the DivX
mode.
[Normal]:
The image is expanded so that the top and
bottom edges of the image fit to the screen,
and that the aspect ratio of the image
becomes 4:3. The aspect ratio of the image
may be changed.
3. Touch the [Hide] key to return to the playback
screen.
English
Operating DivX playback
English
6. SOURCE OPERATIONS
(ACCESSORIES)
Owner’s manual
iPod Operations
iPods can be connected by using the connector cable supplied with the iPod, but in this case, you can
enjoy its audio sound only. To enjoy video movies stored in the iPod with video displaying them on this
unit, it is required to use the special connector cable (CCA-723) separately sold.
Note:
• This system will not operate or may operate improperly with unsupported versions.
• For detailed information on the playable iPod models, see our home page: www.clarion.com
Notes on using Apple iPod
Selecting the iPod mode
• Do not connect an iPod to this unit with a
headphone connected to the iPod.
• After the iPod has been connected to this unit,
the iPod’s buttons are disabled for operation in
the Music mode. In the Video mode, do not
operate the iPod’s buttons.
• When in the iPod mode, a special iPod control
screen is displayed different from the main
screens for other modes.
• When in the iPod mode, the screen image input
from the AUX terminal is output to the rear
monitor.
• When no data is present, the title display will
remain blank.
• The iPod is used with the equalizer function
turned OFF.
• Set the iPod’s language setting to English
before connecting your iPod. Some characters
of the other languages may not be displayed
correctly in this system.
●Precautions on battery consumption:
If the iPod is connected to this unit when the
iPod’s internal battery has run down, this function
may not operate correctly. You must connect the
iPod after charging the battery if it has run down.
1. Connect your iPod to the USB connector.
The system will automatically detect the
connected device, and change to the USB
mode (iPod mode), and start playback after a
while, from where the iPod has been paused.
See also “Connecting/Disconnecting an USB
Media Device” (page 23).
●When an iPod is already connected
1. Press the [SRC] button to display the Source
screen.
2. Touch the [USB] key to select the iPod mode.
The system changes to the USB mode (iPod
mode), and starts playback from the previous
position.
46
VZ709E
iPod Operations
Operation keys
[R], [F] keys
[MENU] key
Operation display
[Hide] key:
Hides the iPod mode screen to display the
playback picture.
• Displayed only in the Video mode.
[Options] key:
Displays the Options screen. You can specify
repeat and shuffle play modes from this screen.
●Operation display
Play (t)/Pause (G) status display
Track No.
Play mode *1
List keys
[Options] key
[p] key
Song title/
Artist name/
Album title *2
[VIDEO]/[MUSIC] key
[VIDEO] / [MUSIC] key:
Switches the operation mode to the Video mode
or Music mode.
• Displayed only when an iPod with video
features is connected.
[MENU] key:
Displays the iPod Menu screen to search tacks to
be played. Various list screens can be displayed
from the iPod Menu screen.
[p] key:
Use to control playback and pause.
[R], [F] keys:
Use to perform track selection. Touch and hold to
enable fast-forward or fast-backward.
Progress
indicator
Play time
Remaining time
Note:
*1 Displays status of Repeat, Shuffle play.
: 1-track Repeat
S
: All Repeat
A
S
: Song Shuffle
A
: Album Shuffle
*2 Touch the operation display to scroll the Song
title.
Pausing playback
1. Touch the [p] key during playback.
Playback pauses.
2. To resume playback, touch the [p] key
again.
Playback resumes.
VZ709E
47
Owner’s manual
●iPod mode screen
List keys:
Displays the corresponding list screen.
[Playlists], [Artists], and [Albums] are available
in the Music mode.
English
Controlling the iPod
iPod Operations
English
Skipping a track (searching)
Owner’s manual
1. Press the [R] or [F] button during
playback.
Tracks are skipped, as many as the times the
button is pressed, and playback starts.
• Pressing the [F] button starts playback
from the beginning of the next track.
• Pressing the [R] button starts playback
from the beginning of the current track.
When this button is pressed again within
about 2 seconds, playback starts from the
beginning of the previous track.
• You can also use the [R] and [F] keys
instead of the [R] and [F] buttons.
Fast forward and fast backward
1. Press and hold the [R] or [F] button
during playback.
The playback speed becomes faster.
Releasing the button resumes the normal
speed playback.
• You can also use the [R] and [F] keys
instead of the [R] and [F] buttons.
Other various play functions
1. Touch the [Options] key.
2. Touch a touch key of the function you want to
play.
1-track repeat:
Touch the [One] key of the Repeat item.
• This operation plays back the current or
selected track repeatedly.
All repeat:
Touch the [All] key of the Repeat item.
• This operation plays back all the tracks
currently selected repeatedly.
Song shuffle:
Touch the [Song] key of the Shuffle item.
• This operation plays back all the tracks
currently selected in a random order.
Album shuffle:
Touch the [Album] key of the Shuffle item.
• When more than one album is selected, this
operation plays back the albums in no
particular order. Tracks in an album are
played back in the recorded order.
3. To cancel the shuffle play, touch the [OFF]
key of the function to cancel.
• The repeat play cannot be canceled.
Normally, it should be set to the All repeat
play.
4. Touch the [Back] key to return to the previous
screen.
48
VZ709E
iPod Menu Operation
You can specify the tracks to play by narrowing
the following categories:
●In the Music mode
[Albums]:
The list of all the Albums stored in the iPod is
displayed.
[Artists]:
You can narrow the Albums to be listed by
specifying the Artist name.
[Genres]:
You can narrow the Artists to be listed by
specifying the Genre name.
[Songs]:
The list of all the Tracks stored in the iPod is
displayed.
[Playlists]:
The list of all the Playlists stored in the iPod is
displayed.
[Composers]:
You can narrow the Albums to be listed by
specifying the Composer name.
●In the Video mode
• Displayed items may be changed depending
on the firmware version of the iPod.
[Playlists]:
The list of all the Video Playlists stored in the iPod
is displayed.
[Movies]:
The list of all the Movies stored in the iPod is
displayed.
[Music Videos]:
You can narrow the Albums to be listed by
specifying the Artist name.
[TV Shows]:
You can narrow the Seasons to be listed by
specifying the Program title.
[Video Podcasts]:
You can narrow the Tracks to be listed by
specifying the Video Podcast name.
iPod Operations
Viewing video data in the iPod
(only for the iPod with video*)
When you connect an iPod with video by using
the optional connector cable, you can enjoy the
video data stored in the iPod showing them on
the liquid crystal panel of this unit (and the rear
monitor if connected).
* Audio data will not be played back in the Video
mode with the fifth generation iPod.
Owner’s manual
1. Touch the [MENU] key from the iPod mode
screen.
The iPod Menu screen of the current
operation mode is displayed.
English
Displaying the iPod Menu screen
WARNING
Selecting tracks to be played from a
list screen
1. Touch the desired Category key from the iPod
Menu screen to display the corresponding list
screen.
2. Touch the desired item key on the screen to
specify it.
• Touch the [c] or [C] key to scroll the list.
• When a track list of an Album, Playlist, or
Video Playlist is displayed, specifying a
track starts playback of the specified album/
playlist from the specified track.
• When the track list of the Songs is
displayed, specifying a track starts playback
of all the tracks stored in the iPod from the
specified track.
• When the playback starts, the display will
return to the iPod mode screen.
• When the other list screen is displayed,
repeat this operation until you select the
tracks to be played back.
• When video tracks are specified in the
Music mode, only the audio data will be
played back.
• Some videos may be recorded at a higher
volume level than desired. Increase the
volume gradually from the minimal
setting after the video has started.
• For your safety, the driver should not
watch the video or operate the controls
while driving. Please note that watching
and operating the video while driving are
prohibited by law in some countries.
1. Touch the [Video] key on the iPod mode
screen to switch to the Video mode.
2. Play back your desired video tracks.
The specified video image will be displayed
on the rear monitor if connected.
3. Touch the [Hide] key to hide the iPod mode
screen.
The video image will be displayed on this unit.
4. To display the iPod mode screen, touch the
screen.
• When you touch the [Music] key during
playing back video data, audio playback will
continue until you select the music tracks to
be played in the Music mode.
Note:
• “AUDIO ONLY” is displayed when the automobile
is moving.
• Do not operate the original control of the iPod in
the Video mode.
• Video data may not be played back according to
the status of the iPod.
• The volume setting of video data is relatively lower
than audio data. Be sure to lower the volume
setting before switching to the other mode.
• Do not select the categories with no track
registered from the iPod Menu screen. The iPod
may be frozen. If the iPod is frozen, reset the iPod
by following the procedure described in the
instruction manual of the iPod.
• Audio may be played back slightly out of
synchronization with video images.
VZ709E
49
English
USB Memory Operations
This system can play audio files (MP3/WMA/AAC) stored in an USB memory which is recognized as
“USB Mass Storage Class device”. You can use your USB memory as an audio device by simply copying
desired audio files into it.
Owner’s manual
Note:
• This system will not operate or may operate improperly with some USB memory.
• Files protected with any DRM can not be played.
Notes on using USB memories
●General notes
• When no data is present, the message “NO
FILE” will be displayed.
• The USB memory is used with the equalizer
function turned OFF.
●Notes on the MP3/WMA/AAC files
• This system can play the MP3/WMA/AAC files
stored in the USB memory.
• This system cannot play DivX files stored in the
USB memory.
• For AAC files, this system supports only the
MPEG4 Audio files encoded by the iTunes.
• Set the Sampling Frequency to:
For MP3 files:
• MPEG1 Layer3: 32, 44.1, or 48 kHz
• MPEG2 Layer3: 16, 22.05, or 24 kHz
• MPEG2.5 Layer3: 8, 11.025, or 12 kHz
For WMA files: 32, 44.1, or 48 kHz
For AAC files: 44.1 or 48 kHz
• Set the Bit Rate to:
For MP3 files:
• MPEG1 Layer3: 32 to 320 kbps (VBR)
• MPEG2 Layer3: 16 to 160 kbps (VBR)
• MPEG2.5 Layer3: 16 to 160 kbps (VBR)
For WMA files: 32,48, 64, 80, 96, 128, 160, or
192 kbps
For AAC files: 16 to 320 kbps (VBR)
• Add the following file extension using single
byte characters:
For MP3 files: “.MP3” or “.mp3”
For WMA files: “.WMA” or “.wma”
For AAC files: “.M4A” or “.m4a”
●Notes on the folder structure
• The folder hierarchy must be within 8
hierarchical levels. Otherwise, playback will be
impossible.
• The maximum allowable number of folders is
512 (including root directory and folders with no
MP3/WMA/AAC file).
• The maximum allowable number of files in a
folder is 255.
• You can store the MP3 files, WMA files, and
AAC files together in a folder.
●Notes on the Tag titles
The limitations on the Tag titles are same as
those in the MP3/WMA/AAC modes. See
“Displaying MP3/WMA/AAC Tag titles” (page 41).
50
VZ709E
●Folder representation in the folder list
The limitations on the folder representation are
same as those in the MP3/WMA/AAC modes.
See “Folder representation in the folder list”
(page 42).
Selecting the USB Memory
mode
1. Connect your USB memory to the USB
connector.
The system will automatically detect the
connected device, and change to the USB
mode (USB Memory mode), and start
playback after a while. If you reconnect the
same device that you disconnected last, the
system will play back where it left off.
See also “Connecting/Disconnecting an USB
Media Device” (page 23).
●When an USB memory is already connected
1. Press the [SRC] button to display the Source
screen.
2. Touch the [USB] key to select the USB
Memory mode.
The system changes to the USB mode (USB
Memory mode), and starts playback from the
previous position.
Playing back files in the USB
memory
The operations in the USB Memory mode are
same as those in the MP3/WMA/AAC modes.
See “Operating MP3/WMA/AAC playback”
(page 42) for details.
Note:
• When performing the fast forward or fast backward
function, the playback speed will become 10-time
faster. For the VBR files, it may differ depending on
the file.
Some Bluetooth cellular phones have the audio features, and some portable audio player support the
Bluetooth feature. These devices will be called as “Bluetooth audio players” in this manual.
This system can play audio data stored in a Bluetooth audio player.
English
Note:
• The Bluetooth audio players are managed separately from the Bluetooth telephones. However, if the same
device has been registered in the BT Phone mode, the audio player can connect to this unit even when it is
not registered in the Bluetooth mode. If you wish to connect from this unit, register the audio player again in
the Bluetooth mode.
• This system will not operate or may operate improperly with some Bluetooth audio players.
• For detailed information on the playable Bluetooth audio players, see our home page: www.clarion.com
Owner’s manual
Bluetooth Audio Player Operations
Selecting the Bluetooth mode
1. Press the [SRC] button to display the Source
screen.
2. Touch the [Bluetooth] key to select the
Bluetooth mode.
The system changes to the Bluetooth mode.
If the connection with a Bluetooth audio player
has been already established, the system will
start playback after a while.
• When the connection with a Bluetooth audio
player has been established, the name of
the connected audio player is displayed at
the top of the screen, and the “ ” icon is
displayed at the bottom of the screen.
2. When you finish confirming the Bluetooth
information, touch the [Back] key to return to
the previous screen.
If you want to change the Pass Key setting of
this unit, perform the following steps.
• The factory default setting is “1234”.
3. Touch the text box of the Pass Key item to
display the Ten-Key Pad screen.
4. Enter your desired 4-digit PIN number, then
touch the [ENT] key.
Registering your Bluetooth audio
player (Pairing)
You can register up to 5 Bluetooth audio players.
1. Turn on the power of the Bluetooth audio
player you wish to register.
2. Touch the [Device] key to display the Device
Select screen.
Bluetooth audio player
settings
Confirming Bluetooth Information
and setting Pass Key
You can confirm the various information
concerning the Bluetooth Interface features.
1. Touch the [BT Info] key to display the
information on the screen.
3. Touch the [Add] key to display the Add the
Device screen.
4. Touch your desired Device key to select the
key for the Bluetooth audio player to be
registered.
• You cannot select the Device key of which
another Bluetooth audio player is already
registered. Select a blank Device key.
5. Touch the [Search] or [Wait] key.
[Search]:
The system starts searching a Bluetooth
audio player.
[Wait]:
The system waits to be detected by a
Bluetooth audio player.
VZ709E
51
Bluetooth Audio Player Operations
English
Owner’s manual
6. When you specify “Search”, perform the
acknowledgement operation for the Bluetooth
connection on your Bluetooth audio player, if
it is prompted.
When you specify “Wait”, perform the search
operation of Bluetooth devices on your
Bluetooth audio player. Then, touch the name
of the player displayed on the screen of this
unit.
7. If entering the Pass Key code is prompted on
your Bluetooth audio player, enter the Pass
Key code set to this unit.
• You can change the Pass key setting of this
unit from the BT Info screen.
When the pairing operation completes, the
registered Bluetooth audio player is set as the
current device, and the display returns to the
Bluetooth mode screen.
Note:
• You cannot register the same Bluetooth audio
player which is already registered doubly. If you
wish to change the Device key registered, once
delete the corresponding Bluetooth audio player
from the previous Device key, and then register it
again to your desired Device key.
●To delete the Bluetooth audio player
registration
1. Touch the [Device] key.
2. Touch the [Delete] key to display the Delete
the Device screen.
3. Touch the desired Device key you wish to
delete.
A confirmation screen is displayed.
4. Touch the [Yes] key to perform deletion.
Selecting the Bluetooth audio player
To change the current Bluetooth audio player to
the other device which is already registered,
perform the following operation.
1. Touch the [Device] key to display the Device
Select screen.
2. Touch the desired Device key you wish to
use.
The corresponding Bluetooth audio player is
set as the current device.
• If the power of the Bluetooth audio player is
not turned on, turn it on.
• The Bluetooth audio player may prompt to
acknowledge the Bluetooth connection or to
enter the Pass Key code of this unit.
Perform these operations according to the
message displayed.
3. Touch the [Back] key to return to the previous
screen.
52
VZ709E
Controlling the Bluetooth
audio player
Note:
• Occasionally, depending on the environment,
playback sounds may be fragmented, or switch
noises may be generated.
Playing back a music
After the connection with a Bluetooth audio
player is established, the play mode is
automatically engaged.
• When playback is not started, touch the [p]
key.
Pausing playback
1. Touch the [p] key during playback.
Playback pauses.
2. To resume playback, touch the [p] key.
Playback resumes.
Skipping a track (searching)
1. Press the [R] or [F] button during
playback.
Tracks are skipped, as many as the times the
button is pressed, and playback starts.
• You can also use the [R] and [F] keys
instead of the [R] and [F] buttons.
Fast forward and fast backward
1. Press and hold the [R] or [F] button
during playback.
The system enters the fast backward or fast
forward playback mode during pressing the
button.
Releasing the button resumes the normal
speed playback.
• You can also use the [R] and [F] keys
instead of the [R] and [F] buttons.
English
Bluetooth Telephone Operations
Note:
• The Bluetooth cellular phones are managed separately from the Bluetooth audio players. However, when you
wish to use the same device as the audio player, register it in the BT Phone mode ahead. If the same device
has been already registered in the Bluetooth mode, it may connect to this unit even when it has not been
registered in the BT Phone mode. In such case, the Phone Book, History, and 10Key functions are disabled.
• Some cellular phones may not be able to transfer the Phone Book data.
• The Phone Book data transmission may take a long time. The operations of sending calls are disabled during
the data transmission.
• You can talk with other party by using the internal microphone. When it is hard to hear for the other party in
accordance with the communication condition or the used telephone, use the optional microphone (RCB199), and set the Microphone Select setting to “External” (page 54). The sound will be improved, but noises
may still be heard depending on the communication condition.
Selecting the BT Phone mode
1. Press the [MENU] button to display the Menu
screen.
2. Touch the [BT Phone] key to select the BT
Phone mode.
The Telephone screen is displayed.
• When the connection with a Bluetooth
telephone has been established, the “ ”
icon, battery indicator, and signal level
indicator are displayed at the bottom of the
screen.
Telephone settings
Setting the telephone features
1. Touch the [Setting] key to display the
Telephone Settings screen.
2. Perform setting for the desired item.
See the following sections for detail.
3. Touch the [Back] key to return to the previous
screen.
●Setting Automatic Connection
The system automatically reconnects the cellular
phone after the connection is lost or the system
is restarted.
• The factory default setting is “OFF”.
2-1. Touch the [ON] or [OFF] key of the
Automatic Connection item to set the
function ON or OFF.
●Setting Automatic Incoming Call
When a call comes in, the system automatically
connects the call approx. 5 seconds after the
calling starts.
• The factory default setting is “OFF”.
2-1. Touch the [ON] or [OFF] key of the
Automatic Incoming Call item to set the
function ON or OFF.
VZ709E
53
Owner’s manual
When the connection with your Bluetooth cellular phone is established, the following functions are
available on this unit:
• Listening to your telephone calls on the car speakers.
• Answering to an incoming call.
• Making a call using the Ten-Key pad screen.
• Making a call using the Phone Book data in the selected cellular phone.
• Making a call using the History data of the dialed/received calls.
• Redialing
Bluetooth Telephone Operations
English
Owner’s manual
●Setting Noise Canceller
You can reduce noise generated during handsfree talk. This function may reduce the sound
quality.
• Select either LOW or HIGH depending on the
type of your vehicle and cellular phone.
• The factory default setting is “LOW”.
2-1. Touch the [LOW] or [HIGH] key of the Noise
Canceller item to set the function.
[LOW]:
Suitable for a GSM cellular phone.
[HIGH]:
Suitable for a CDMA cellular phone.
●Setting Ring Tone Select
The system can ring if the cellular phone cannot
generate ring tones when the Bluetooth
connection has been established.
• The factory default setting is “AUTO”.
2-1. Touch the [AUTO] or [Internal] key of the
Ring Tone Select item to set the function.
[AUTO]:
The system will ring only when the cellular
phone cannot generate ring tones.
[Internal]:
The system will ring regardless of the
cellular phone. Select this when no ring tone
is generated with the “AUTO” selected.
●Selecting Microphone
You can select the microphone to be used.
• The factory default setting is “Internal”.
2-1. Touch the [C] key to display the next screen.
2-2. Touch the [External] or [Internal] key of the
Microphone Select item to set the function.
Note:
• When the “Internal” is selected, and a call comes
in during the liquid crystal panel closed, you cannot
talk to the other party because the microphone is
on the liquid crystal panel. To talk to the other
party, open the liquid crystal panel.
• When the “Internal” is selected, the [OPEN] button
and the [Tilt] key are disabled during a call.
●Setting Microphone Gain
You can adjust the input level of the microphone
in 5 levels.
• The factory default setting is “3”.
Note:
• The input level of the microphone can be affected
by its surroundings. Adjust the level when the
person on the other end of the telephone has a
reception problem.
2-1. Touch the [C] key to display the next screen.
2-2. Touch the [[] or []] key of the Microphone
Gain item to adjust the input level.
●Setting Ring Tone Volume
You can adjust the volume of the ring tone in 10
levels.
• The factory default setting is “5”.
●Confirming Bluetooth Information and
setting Pass Key
You can confirm the various information
concerning the Bluetooth Interface features.
2-1. Touch the [[] or []] key of the Ring Tone
Volume item to adjust the volume level.
2-1. Touch the [C] key to display the next screen.
●Setting Registration Type
You can change the distribution of maximum
number of Phone Book data can be registered to
each telephone.
• The factory default setting is “3”.
2-1. Touch the [C] key to display the next screen.
2-2. Touch the [1], [2], or [3] key of the
Registration Type item to set the function.
[1]:
Allows 250 records for first two cellular
phones, and no record for the others.
[2]:
Allows 200 records for first cellular phone,
100 records for second and third cellular
phones, and 50 records for the others.
[3]:
Allows 100 records for each cellular phone.
54
VZ709E
2-2. Touch the [Info] key of the BT Info item to
display the information on the screen.
2-3. When you finish confirming the Bluetooth
information, touch the [Back] key to return to
the previous screen.
If you want to change the Pass Key setting
of this unit, perform the following steps.
2-4. Touch the text box of the Pass Key item to
display the Ten-Key Pad screen.
• The factory default setting is “1234”.
2-5. Enter your desired 4-digit PIN number, then
touch the [ENT] key.
Registering your cellular phone
(Pairing)
You can register up to 5 cellular phones.
1. Turn on the power of the cellular phone you
wish to register.
Bluetooth Telephone Operations
3. Touch the desired Cellular key you wish to
delete.
A confirmation screen is displayed.
4. Touch the [Yes] key to perform deletion.
3. Touch the [Add] key to display the Add the
Cellular screen.
4. Touch your desired Cellular key to select the
key for the cellular phone to be registered.
• You cannot select the Cellular key of which
another cellular phone is already registered.
Select a blank Cellular key.
5. Touch the [Search] or [Wait] key.
[Search]:
The system starts searching a cellular phone.
[Wait]:
The system waits to be detected by a cellular
phone.
6. When you specify “Search”, perform the
acknowledgement operation for the Bluetooth
connection on your cellular phone, if it is
prompted.
When you specify “Wait”, perform the search
operation of Bluetooth devices on your
cellular phone. Then, touch the name of the
cellular phone displayed on the screen of this
unit.
7. If entering the Pass Key code is prompted on
your cellular phone, enter the Pass Key code
set to this unit.
• You can change the Pass key setting of this
unit by the BT Info screen under the
Telephone Settings screen.
When the pairing operation completes, the
registered cellular phone is set as the current
telephone, and the display returns to the
Telephone screen.
Note:
• You cannot register the same cellular phone which
is already registered doubly. If you wish to change
the Cellular key registered, once delete the
corresponding cellular phone from the current
Cellular key, and then register it again to your
desired Cellular key.
●To delete the cellular phone registration
1. Touch the [Cellular] key.
2. Touch the [Delete] key to display the Delete
the Cellular screen.
To change the current cellular phone to the other
device which is already registered, perform the
following operation.
1. Touch the [Cellular] key to display the
Cellular Select screen.
2. Touch the desired Telephone key you wish to
use.
The corresponding cellular phone is set as the
current telephone.
• If the power of the cellular phone is not
turned on, turn it on.
• The cellular phone may prompt to
acknowledge the Bluetooth connection or to
enter the Pass Key code of this unit.
Perform these operations according to the
message displayed.
3. Touch the [Back] key to return to the previous
screen.
Obtaining the Phone Book data
Sending the Phone Book data from the cellular
phone enables you to make a call using the
Phone Book function from this unit.
1. Perform the Object Push transfer operation of
the Phone Book data on the current cellular
phone.
For details of the operation, see the operation
manual of the cellular phone.
Note:
• Some cellular phones may not be able to transfer
the Phone Book data.
• Some cellular phones cannot transfer the Phone
Book data when the hands-free mode is set or it is
also registered in the Bluetooth mode. In those
cases, disable these functions from the cellular
phone before performing the Object Push transfer.
Telephone operations
Note:
• For your safety, this system disables the calling
functions when the car is moving. Be sure to stop the
car and apply the parking brake before making a call.
Making a call using the Ten-Key pad
1. Touch the [10Key] key to display the Ten-Key
pad screen.
2. Enter the telephone number by using the TenKey pad displayed on the screen.
VZ709E
55
Owner’s manual
Selecting the cellular phone
English
2. Touch the [Cellular] key to display the
Cellular Select screen.
Bluetooth Telephone Operations
English
3. Touch the [
] (Send) key to call the entered
number.
• The following Telephone Interrupt screen is
displayed during phone call.
Owner’s manual
• Touch the [Private] key to talk using the
cellular phone canceling the hands-free
function. To return to the hands-free mode,
touch the [Hands Free] key.
• Touch the [Mic] key to turn off the
microphone so that the sound does not be
heard by the partner.
4. When the call is finished, touch the [End] key
to hang up.
The display will return to the previous mode
screen selected before entering the BT Phone
mode.
Note:
• Depending on the cellular phone, the Telephone
Interrupt screen may be closed and the connection
with this system may be disconnected when
entering the Private mode.
Redialing
1. Touch the [Redial] key to call the last dialed
number.
The Telephone Interrupt screen is displayed,
and calling starts.
• When the call is finished, touch the [End]
key to hang up.
Note:
• When the dialed telephone number cannot be
transferred from the cellular phone, “Unknown” is
displayed instead of the number.
2. Touch the desired Name key you wish to dial.
• Touch the [c] or [C] key to scroll the list.
• When you touch the alphabet key at the
right of the screen, the list scrolls to the item
which starts with the specified character.
3. Touch the desired Number key you wish to
dial.
The confirming message will appear.
4. Touch the [Yes] key to call the specified
number.
The Telephone Interrupt screen is displayed,
and calling starts.
• When the call is finished, touch the [End]
key to hang up.
Making a call using the History
The system will memorize the Dialed/Received
calls record data in the memory. You can confirm
it and use it to make a call from this unit.
1. Touch the [History] key.
The History List screen is displayed.
• The items are sorted in the order of the
number of times of Dialed/Received calls.
• Touch the [c] or [C] key to scroll the list.
• Touch the [Back] key to return to the
previous screen.
2. Touch the desired History item key you wish
to dial.
The confirming message will appear.
3. Touch the [Yes] key to call the specified
number.
The Telephone Interrupt screen is displayed,
and calling starts.
• When the call is finished, touch the [End]
key to hang up.
Answering to an incoming call
When a call comes in, the following Telephone
Interrupt screen appears.
Making a call using the Phone Book
You can use the Phone Book data obtained from
the cellular phone to make a call from this unit.
Note:
• Before using this function, the Phone Book data
must be sent from the cellular phone (see
page 55).
• Only the Phone Book items with at least one
telephone number registered in the captured
Phone Book data are displayed on the Phone Book
screen.
1. Touch the [PhoneBook] key to display the
Phone Book screen.
56
VZ709E
You can answer to the incoming call on this
system by the following operation.
1. Press the [ ] (Voice/SEND/END) button or
touch the [Send] key to answer to the call.
• When the call is finished, touch the [End]
key to hang up.
Notes on the NAVI functions
[MENU] button
• When in the NAVI mode, displays the Menu
screen of this unit.
[ ] (Voice/SEND/END) button*2
• Pressing this button displays the Voice
Command screen of the navigation system.
Note:
*1 The CeNET Convert Box CCB509 is required to
connect the NP509E.
*2 This button does not work with the NP509E.
NAVI operations
Changes between the NAVI display and the
Audio/Visual (hereinafter, referred as “AV”)
display.
Note:
• The below-mentioned operations are available
only when the Clarion NAVI (NP509E*1/
NAX983HD/NAX973HD/NAX963HD) is
connected.
●When in the AV mode
• Press the [MAP] button to switch to the NAVI
mode. You can also select it by touching the
[Navigation] key from the Menu screen.
• When the image interruption from the NAVI
arises, the screen will be changed to the NAVI
display. When the interruption is finished, the
screen will return to the previous AV display.
●When in the NAVI mode
• NP509E: Press the [MAP] button to switch to
the AV mode.
• NAX983HD/NAX973HD/NAX963HD: Touch
the [AV] key on the screen to switch to the AV
mode.
• AV operations made in the NAVI mode will be
indicated for about 2 seconds at the bottom of
the NAVI screen.
●Button operations
[MAP] button
• When in the AV mode, pressing this button
switches to the NAVI mode.
• NP509E: When in the NAVI mode, pressing
this button switches to the AV mode.
• NAX983HD/NAX973HD/NAX963HD: When in
the NAVI mode, the Map screen of the NAVI
will be displayed.
VZ709E
57
Owner’s manual
• Hereafter in this section, the Navigation system
will be called as “NAVI”.
• When the Clarion NAVI NP509E*1/
NAX983HD/NAX973HD/NAX963HD is
connected, the following functions are
available:
• Showing the NAVI display
• Operation by using the touchkeys on screen
• NAVI guidance voice interruption
• When a voice interrupt of the NAVI arises
during 2Zone ON, the sound of the Main zone
is muted, and the sound of the Sub zone is
output normally. When it arises during 2Zone
OFF, the audio signals to the 4ch speakers are
attenuated, and the voice from the navigation
system is output from the front two speakers.
English
Navigation System Operations
English
AUX Operations
This function is available when a VTR, etc. is connected to the AUX terminal.
WARNING
Owner’s manual
• For your safety, the driver should not watch the video or operate the controls while driving.
Please note that watching and operating the video while driving are prohibited by law in
some countries.
Note:
• For your safety, this system has a safety function which turns off the picture when the car is moving, so only
the audio can be heard. The picture can only be watched when the car is stopped and the parking brake is
applied.
• When an iPod with video is connected using the special connector cable (CCA-723) separately sold, the video
input from the iPod will be output to the monitor screen and rear monitor even in the AUX mode. However,
you must select the iPod mode to control the iPod.
Selecting the AUX mode
Selecting the screen size
1. Press the [SRC] button, and touch the [AUX]
key.
You can change the screen size to suit to the
video image.
• The factory default setting is “F.Wide”.
1. Touch the screen to display the AUX mode
screen.
2. Repeat touching the [F.Wide/Cinema/
Normal/Wide] key until your desired screen
size is selected.
• This key shows the current screen size
setting.
[F.Wide]:
The image is expanded so that the rectangle
of the image fits to the screen (16:9). The
aspect ratio of the image may be changed.
[Cinema]:
The image is expanded so that the top and
bottom edges of the image fit to the screen.
[Normal]:
The image is expanded so that the top and
bottom edges of the image fit to the screen,
and that the aspect ratio of the image
becomes 4:3. The aspect ratio of the image
may be changed.
[Wide]:
The image is expanded in the same way as
the [F.Wide] setting, but the width will become
narrower. Depending on the image data,
black areas may be displayed at the both
sides of the screen.
3. Touch the [Hide] key to return to the video
screen.
Showing the AUX mode screen
The AUX mode screen is used to adjust settings
concerning the AUX mode.
1. Touch the screen.
The AUX mode screen is displayed.
If you do not touch the screen for 7 seconds,
the display will return to the video screen.
Changing the audio input level
The input audio level of the AUX terminals can be
changed.
• The factory default setting is “HIGH”.
1. Touch the screen to display the AUX mode
screen, then repeat touching the [SENS] key
to select the level.
HIGH: 10 dB
MID: 4 dB
LOW: 0 dB
58
VZ709E
English
7. SYSTEM SETTINGS
Audio Settings
Setting the DZE (Digital ZEnhancer)
You can customize the various audio settings of
this unit from the Audio Settings screen.
1. Press the [MENU] button.
The Menu screen appears.
2. Touch the [Audio] key.
The Audio Settings screen appears.
This system provides 3 types of sound tone
effects stored in memory. You can select desired
setting.
• The factory default setting is “OFF”.
3. Touch the desired Tab key, and perform the
adjustment.
See the following sections for details.
• In the following sections, only the details
regarding adjustments are described,
procedures to select items are skipped.
4. When the adjustment completes, touch the
[Back] key to return to the previous screen.
3-1. Touch the [DZE] key to display the DZE tab
screen.
3-2. Touch the [OFF], [DZE 1], [DZE 2], or [DZE
3] key you wish to set.
[OFF]:
No sound effect.
[DZE 1]:
Suitable for the genuine speakers.
[DZE 2]:
Suitable for separate speakers
commercially sold.
[DZE 3]:
Suitable for the coaxial speakers
commercially sold.
3-3. When you select an item other than “OFF” in
step 2, adjust the effect level by touching the
[[] or []] key.
Setting range: –3 to 3
• The factory default setting is “0”.
Notes:
• The volume changes each time the DZE setting is
switched.
• Sufficient effects cannot be obtained with some
speaker systems. In such cases, adjust the
volume.
• When you set the DZE to other than “OFF”, the
TONE and M-B EX (Magna Bass Extend) settings
are disabled.
VZ709E
59
Owner’s manual
Displaying the Audio Settings
screen
Audio Settings
English
Adjusting the Tone
You can adjust the sound tone by performing the
following adjustments.
Owner’s manual
Note:
• These operations are disabled when the DZE
(Digital Z-Enhancer) function is set to other than
“OFF”.
Adjusting the BASS
The bass gain, bass frequency (center
frequency) and bass Q can be adjusted as
follows.
3-1. Touch the [TONE] key to display the TONE
tab screen.
Adjusting the TREBLE
The treble gain and treble frequency (center
frequency) can be adjusted as follows.
3-1. Touch the [TONE] key to display the TONE
tab screen.
3-2. Touch the [TREBLE] key.
3-3. Touch the [[] or []] key for the desirable type
to adjust to a desirable level.
GAIN: –6 to 6
• The factory default setting is “0”.
FREQ: 8kHz, 12kHz
• The factory default setting is “12kHz”.
Adjusting the Balance/Fader
3-2. Touch the [BASS] key.
3-3. Touch the [[] or []] key for the desirable type
to adjust to a desirable level.
GAIN: –6 to 8
• The factory default setting is “0”.
FREQ: 50Hz, 80Hz, 120Hz
• The factory default setting is “50Hz”.
Q: 1, 1.25, 1.5, 2
• The factory default setting is “1”.
Adjusting the MID
The middle gain, middle frequency (center
frequency) and middle Q can be adjusted as
follows.
3-1. Touch the [TONE] key to display the TONE
tab screen.
3-2. Touch the [MID] key.
3-3. Touch the [[] or []] key for the desirable type
to adjust to a desirable level.
GAIN: –6 to 6
• The factory default setting is “0”.
FREQ: 700Hz, 1kHz, 2kHz
• The factory default setting is “1kHz”.
Q: 1.5, 2
• The factory default setting is “2”.
3-1. Touch the [BAL/FAD] key to display the
BAL/FAD tab screen.
3-2. Touch the [{] or [}] key to adjust the fader
level.
[{]:
Emphasizes the sound from the front
speakers.
[}]:
Emphasizes the sound from the rear
speakers.
Adjustment range: front 12 to rear 12
• The factory default setting is “0”.
3-3. Touch the [[] or []] key to adjust the balance
level.
[[]:
Emphasizes the sound from the left
speakers.
[]]:
Emphasizes the sound from the right
speakers.
Adjustment range: left 12 to right 12
• The factory default setting is “0”.
Adjusting the Non-Fader
output volume
You can adjust the volume output from the unit's
non-fader output terminal.
3-1. Touch the [OTHERS] key to display the
OTHERS tab screen.
3-2. Touch the [–] or [+] key of the NON FADER
VOL item to adjust to desirable level.
Setting range: –6 to 6
• The factory default setting is “0”.
60
VZ709E
Audio Settings
English
Turning on/off the MagnaBass EXtend
Owner’s manual
The Magna Bass Extend does not adjust the low
sound area like the normal sound adjustment
function, but emphasizes the deep bass sound
area to provide you with a dynamic sound.
• The factory default setting is “OFF”
Note:
• This operation is disabled when the DZE (Digital ZEnhancer) function is set to other than “OFF”.
3-1. Touch the [OTHERS] key to display the
OTHERS tab screen.
3-2. Touch the [ON] or [OFF] key of the M-B EX
item to turn the Magna Bass Extend function
on or off.
Adjusting the High Pass Filter
You can adjust the cut-off frequency of the High
Pass Filter for the front/rear speaker output.
• The factory default setting is “Through”.
3-1. Touch the [OTHERS] key to display the
OTHERS tab screen.
3-2. Touch the [50Hz], [80Hz], [120Hz], or
[Through] key of the HIGH PASS FILTER
item to adjust setting.
Adjusting the Low Pass Filter
You can adjust the cut-off frequency of the Low
Pass Filter for the non-fader output.
• The factory default setting is “Through”.
3-1. Touch the [OTHERS] key to display the
OTHERS tab screen.
3-2. Touch the [50Hz], [80Hz], [120Hz], or
[Through] key of the LOW PASS FILTER
item to adjust setting.
Setting the Amp Cancel
When an external amplifier is used, using this
function reduces power noises of the audio lines.
• The factory default setting is “OFF”.
3-1. Touch the [OTHERS] key to display the
OTHERS tab screen.
3-2. Touch the [ON] or [OFF] key of the AMP
CANCEL item to turn the Amp Cancel
function on or off.
VZ709E
61
English
General Settings
Owner’s manual
Displaying the General
Settings screen
Setting the VTR system
(NTSC/PAL)
You can customize the various settings of this
unit from the General Settings screen.
1. Press the [MENU] button.
The Menu screen appears.
2. Touch the [General] key.
The General Settings screen appears.
• The factory default setting is “PAL”.
Note:
• This setting is applied only to the AUX video input.
3-1. Touch the [Display] key to display the
Display tab screen.
3-2. Touch the [NTSC] or [PAL] key of the
NTSC/PAL item to set the VTR system.
Setting the Auto Panel
3. Touch the desired Tab key, and perform the
adjustment.
See the following sections for details.
• In the following sections, only the details
regarding adjustments are described,
procedures to select items are skipped.
4. When the adjustment completes, touch the
[Back] key to return to the previous screen.
Setting Camera Interrupt
When the optional Rear Vision Camera is
connected to this unit, the rear view image is
displayed on the screen when the gear lever is
put in the reverse gear position.
• The factory default setting is “OFF”.
3-1. Touch the [Display] key to display the
Display tab screen.
3-2. Touch the [ON] or [OFF] key of the Camera
Interrupt item to turn the Camera Interrupt
function on or off.
Setting Camera Warning
The following warning message is displayed
during use of the Rear Vision Camera: “Make
sure of safety around your vehicle”.
• The factory default setting is “ON”.
Note:
• This setting is disabled when the Camera Interrupt
feature is set to OFF.
3-1. Touch the [Display] key to display the
Display tab screen.
3-2. Touch the [ON] or [OFF] key of the Camera
Warning item to turn the Camera Warning
function on or off.
62
VZ709E
When you remove or attach the DCP
(Detachable Control Panel), you can set the
liquid crystal panel automatically housing or
opening.
• The factory default setting is “ON”.
3-1. Touch the [Display] key to display the
Display tab screen.
3-2. Touch the [ON], [OFF], or [Close] key of the
Auto PANEL item to set to “ON”, “OFF”, or
“Close”.
[ON]:
The liquid crystal panel houses
automatically after removing the DCP. And
the liquid crystal panel opens automatically
after attaching the DCP.
[OFF]:
Normal operation.
[Close]:
The liquid crystal panel houses
automatically after removing the DCP.
Setting the time of air
conditioner operation mode
(HVAC)
This setting can be used to adjust the time the
panel stays in the horizontal position when in the
air conditioner operation mode.
• The factory default setting is “10 seconds”.
3-1. Touch the [Display] key to display the
Display tab screen.
3-2. Touch the [C] key to display the next screen.
3-3. Touch the [5s], [10s], or [30s] key of the
HVAC item to set the time to “5 seconds”,
“10 seconds”, or “30 seconds”.
General Settings
3-1. Touch the [System] key to display the
System tab screen.
3-4. Touch the [Yes] key to perform the system
check manually.
The system will be restarted after
performing the system check.
3-2. Touch the [ON] or [OFF] key of the Beep
item to turn the Beep function on or off.
Setting the Audio
ATTenuation
Setting the Blink LED
The audio output can be attenuated when a voice
interrupt of the navigation system arises.
• The factory default setting is “High”.
You can set the unit to blink the Blink LED
indication when the DCP (Detachable Control
Panel) is removed.
• The factory default setting is “OFF”.
Note:
• This setting is enabled only when the Navigation
System is connected to this unit.
3-1. Touch the [System] key to display the
System tab screen.
3-1. Touch the [System] key to display the
System tab screen.
3-2. Touch the [ON] or [OFF] key of the Blink
LED item to turn the Blink LED function on or
off.
3-2. Touch the [C] key to display the next screen.
Confirming the DivX
Registration Code and DivX
URL
When you download a DivX VOD (Video-onDemand) file from a web site, entering the
registration code of your playback system may
be required to authorize the file. You can confirm
the registration code of your system and the URL
information by the following operation.
3-3. Touch the [High], [Mid], [Low], or [Mute]
key of the Audio ATT item to set the volume
level when a voice interrupt arises.
Setting the Auto Antenna
When an auto antenna which is extended
automatically is used, you can set so that it is
automatically extended/collapsed according to
the power setting of this unit.
Note:
• This setting is enabled only when the Navigation
System is connected to this unit.
3-1. Touch the [System] key to display the
System tab screen.
3-1. Touch the [System] key to display the
System tab screen.
3-2. Confirm the displayed information of the
DivX Registration Code and DivX URL
items.
3-2. Touch the [C] key to display the next screen.
3-3. Touch the [ON] or [OFF] key of the Auto
Antenna item to turn this function on or off.
Note:
• The DivX registration code is not displayed when a
disc is set in the DVD player.
Changing the Wall Paper
Performing the System Check
You can change the wall paper (background
image on the most screens) by selecting it from
the Wall Paper tab screen.
You can perform the system check by the
following operation.
3-1. Touch the [Wall Paper] key to display the
Wall Paper tab screen.
3-1. Touch the [System] key to display the
System tab screen.
3-2. Touch the desired Wall Paper key you wish
to set.
The background image of the screen will be
changed to the selected image.
3-2. Touch the [C] key to display the next screen.
VZ709E
63
Owner’s manual
The sound heard when you make operations is
called “beep”. The system can be set so that it
does not produce this beep sound.
• The factory default setting is “ON”.
3-3. Touch the [Check] key of the System Check
item.
A confirmation screen is displayed.
English
Setting the Beep
English
Adjusting the Monitor
You can customize the various monitor settings by the following operations.
Setting the Screen mode
Owner’s manual
The system has two screen modes: the Day
mode and Night mode. Each mode has the own
dimmer setting. You can select these modes
temporarily by performing the following
operation. This setting will automatically return to
the Auto mode when turning the car lights on/off
or turning off the ignition switch.
• The factory default setting is “Auto”.
1. Press the [MENU] button to display the Menu
screen.
2. Touch the [Day], [Night], or [Auto] key to set
the Screen mode.
[Day]:
Set the dimmer level temporarily to the Day
mode (brighter).
[Night]:
Set the dimmer level temporarily to the Night
mode (dimmer).
[Auto]:
The dimmer level is changed according to the
status of the car light:
When the car light is off: Day mode
When the car light is on: Night mode
3. Touch the [Back] key to return to the previous
screen.
Note:
• When the navigation system is connected, this
setting also works upon the Color mode of the
navigation system.
Adjusting the Dimmer, Bright,
Color, Contrast, and Hue level
Note:
• The Bright, Color, Contrast, and Hue settings can
be adjusted only when a video image is displayed
on the screen, and the car is stopped with applying
the parking brake.
• The Hue setting can be adjusted only when the
NTSC mode is selected.
• The navigation screen has own dimmer setting
separately from the AV screen. The dimmer
adjustment in a mode does not affect each other
screen.
• The Rear Vision Camera image cannot be
adjusted directly. Perform the adjustments when
displaying a video image of the other source.
1. Press the [MENU] button to display the Menu
screen.
64
VZ709E
2. Touch the [Monitor] key to display the
Monitor Settings screen.
3. Touch the [Dimmer], [Bright], [Color],
[Contrast], or [Hue] key you wish to adjust,
then touch the [[] or []] key to adjust the level.
[Dimmer]:
Adjusts the panel brightness when the car
lights are ON or OFF.
[]]: Press to make image brighter.
[[]: Press to make image dimmer.
[Bright]:
Adjusts the brightness of the display.
[]]: Press to make image brighter.
[[]: Press to make image dimmer.
[Color]:
Adjusts the color saturation.
[]]: Press to increase color depth.
[[]: Press to decrease color depth.
[Contrast]:
Adjusts the contrast of the display.
[]]: Press to make contrast higher.
[[]: Press to make contrast lower.
[Hue]:
Adjusts the tone of color (red is emphasized
or green is emphasized).
[]]: Press to increase green.
[[]: Press to increase red.
4. When the adjustment completes, touch the
[Back] key to return to the previous screen.
If you have a problem with this system, check the following items to resolve it. See also our homepage
(www.clarion.com) for additional information.
Problem
Cause
Measure
Power does not turn
on. (No sound is
produced.)
Fuse is blown.
Replace with a fuse of the same amperage. If the
fuse blows again, consult your store of purchase.
Incorrect wiring.
Consult your store of purchase.
Nothing happens
when buttons are
pressed.
The microprocessor has
malfunctioned due to
noise, etc.
Turn off the power and remove the DCP. Press the
reset button with a thin rod.
Display is not
accurate.
Note:
When the Reset button is pressed, turn off the ACC
power.
Reset button
• When the Reset button is pressed, frequencies
of radio stations, etc. stored in memory are
cleared.
The remote control
unit does not work.
Direct rays of the sun fall on When direct rays of the sun fall on the lightthe light-receptive part of
receptive part of the remote control unit, it may not
the remote control unit.
work.
Check the battery of the remote control unit.
The battery of the remote
control unit is dead or there
is no battery in the remote
control unit.
The display is dark.
The Dimmer control is too
low.
Adjust the Dimmer properly.
The operating condition is
not good.
The temperature inside the vehicle may be 0°C or
lower. Set to an appropriate temperature (25°C or
so) and check it again.
The headlight of the vehicle The display is made dark at night to prevent the
is lit.
glare (when the headlight is the vehicle is lit in the
daytime, the display gets dark).
There are red, green
and blue points in
the display.
This is not a failure, but a phenomenon peculiar to
a liquid crystal panel (The liquid crystal panel is
produced according to technology with very high
precision. Note that, though there are effective
pixels of 99.99% or more, pixel missing or
normally lit pixels account for 0.01%).
VZ709E
65
Owner’s manual
General
English
8. TROUBLESHOOTING
DVD Player
English
Problem
Disc cannot be
loaded.
Owner’s manual
Sound skips or is
noisy.
Cause
Measure
Another disc is already
loaded.
Eject the disc before loading the new one.
There is a foreign matter
already in place.
Eject the foreign matter forcibly.
Disc is dirty.
Clean the disc with a soft cloth.
Disc is heavily scratched or Replace with a disc with no scratches.
warped.
MP3/WMA/AAC files are
not encoded properly.
Use MP3/WMA/AAC files encoded properly.
Let dry for about 1 hour with the power on.
Sound is bad directly Water droplets may form
after power is turned on the internal lens when
on.
the car is parked in a humid
place.
The image is not
displayed.
The parking brake is not
engaged.
Disc cannot play with The view is limited.
the display
“PARENTAL
VIOLATION” shown.
The color of the
display is light or a
shade of color is not
good.
The color is not adjusted
adequately.
Check that the parking brake is engaged.
Release the view limitation or change the parental
level.
See the subsection “Setting up the parental level”
(page 35).
Check that the Bright, Color, Contrast, and Hue
are adjusted properly.
USB Devices
Problem
USB device cannot
be inserted.
USB device is not
recognized.
Cause
Measure
The USB device has been
inserted with wrong
direction.
Reversing the connection direction of the USB
device, try it again.
The USB connector is
broken.
Replace with a new USB device.
The USB device is
damaged.
Disconnect the USB device and reconnect. If the
device is still not recognized, try replacing with a
different USB device.
Connectors are loose.
No sound heard with No MP3/WMA/AAC file is
the display “NO
stored in the USB device.
FILE” shown.
Store these files properly in the USB device.
Sound skips or is
noisy.
MP3/WMA/AAC files are
not encoded properly.
Use MP3/WMA/AAC files encoded properly.
The iPod’s video
image is disturbed.
The TV Signal setting of
Set the TV Signal setting (NTSC/PAL) of the iPod
the iPod is not set correctly. correctly.
66
VZ709E
English
9. ERROR DISPLAYS
If an error occurs, one of the following displays is displayed.
Take the measures described below to solve the problem.
Owner’s manual
DVD Player
Display
Cause
Measure
ERROR 2
A disc is caught inside the
DVD player and is not
ejected.
This is a failure of DVD player’s mechanism.
Consult your store of purchase.
ERROR 3
A disc cannot be played
due to scratches, etc.
Replace with a non-scratched, non-warped disc.
ERROR 6
A disc is loaded upsidedown inside the DVD
player and does not play.
Eject the disc then reload it properly.
No MP3/WMA/AAC/DivX
Write these files properly onto a disc.
file is recorded on the disc.
File system is not correct.
Use ISO9660 level 1/2, Romeo, Joliet, or Apple
ISO file system for CD-R/RW, or UDF for DVD±R/
RW.
PARENTAL
VIOLATION
Parental level error
Set the correct Parental level.
WRONG REGION
Region code error
Eject the disc, and replace correct region code
disc.
DRM
WMA files protected by
DRM are played.
NOT SUPPORT
Files not supported by this
unit are played.
Perform the operation such as skipping a file.
(Repeat and random playback mode may be
canceled.)
USB Devices
Display
ERROR 2
Cause
Measure
The connected USB device If the USB device is frozen, disconnect it, reset it,
is not supported.
and reconnect it again.
Connect a proper USB device.
ERROR 3
(USB memory)
An error occurred when
Disconnect the USB device, and reconnect it
controlling the USB device. again.
ERROR 3 (iPod)
The selected category has
no track data.
Press the [F] button. If the error is not cleared,
disconnect the iPod, and reconnect it again.
The iPod is frozen.
Disconnect the iPod, reset it, and reconnect it
again.
The connected iPod is not
recognized.
Disconnect the iPod, and reconnect it again. If the
iPod is still not recognized, try replacing with a
different iPod.
ERROR 5 (iPod)
If the iPod is frozen, disconnect it, reset it, and
reconnect it again.
VZ709E
67
Display
English
Owner’s manual
Cause
Measure
BUS ERROR
Over-current or data error
is detected.
Turn off the ignition switch, disconnect the device,
restart the engine and reconnect it again. If the
device is still not recognized, try replacing with a
different device.
DEVICE ERROR
The device is connected
via the USB Hub.
Disconnect the device, and reconnect directly to
the USB connector of this unit without using the
USB Hub.
DRM
WMA files protected by
DRM are played.
NOT SUPPORT
Files not supported by this
unit are played.
Perform the operation such as skipping a file.
(Repeat and random playback mode may be
canceled.)
If an error display other than the ones described above appears, press the Reset button. If the problem
persists, turn off the power and consult your store of purchase.
• When the Reset button is pressed, frequencies of radio stations, etc. stored in memory are cleared.
68
VZ709E
English
10.SPECIFICATIONS
Input
Frequency Range: 87.50 MHz to 108.00 MHz
Usable Sensitivity: 9 dBf
50dB Quieting Sensitivity: 15 dBf
Alternate Channel Selectivity: 70 dB
Stereo Separation (1 kHz): 35 dB
Frequency Response (r3 dB): 30 Hz to 15 kHz
Audio input sensitivity:
High: 0.65 V (at 2 V output)
Mid: 1.3 V (at 2 V output)
Low: 2.0 V (at 2 V output)
(input impedance 10 k: or greater)
Video input:
1.0 r0.2 Vp-p (input impedance 75 :)
DVD Player
System:
Digital Versatile Disc System with CDDA
capable
Usable discs:
DVD video disc, Compact disc
Frequency Response:
20 Hz to 20 kHz (CD) (r1 dB)
Signal to Noise Ratio: 100 dB (1 kHz)
Dynamic Range: 100 dB (1 kHz)
Distortion: 0.01%
USB
Specification: USB 2.0 Full Speed
File system: FAT12/16/32
Playable audio format:
MP3 (.mp3): MPEG1/2 Audio Layer-3
WMA (.wma): Ver. 7/8/9.1/9.2
AAC (.m4a): AAC format encoded by iTunes
and iTunes+ only
Maximum number of folders: 512
Maximum number of files: 255 (for a folder)
Maximum folder hierarchy: 8 levels (including Root)
Maximum power supply: 500 mA
Video Output
Video output:
1.0 r0.2 Vp-p (output impedance 75 :)
LCD Monitor
Screen Size: 7-inch wide type
152 mm Width u 85 mm Height
Display method:
Transmission type TN liquid crystal display
Drive method: TFT (thin-film transistor)
active matrix driving
Pixels: 336,960 (1440 u 234)
General
Power source voltage:
14.4 V DC (10.8 to 15.6 V allowable)
Ground: Negative
Current consumption: 4.0 A (1 W)
Auto Antenna Rated Current: 500 mA less
Dimensions of the Main Unit:
178 mm Width u 50 mm Height u 165 mm Depth
Weight of the Main Unit: 2.4 kg
Dimensions of the Remote Control Unit:
43.4 mm Width u 12.5 mm Height u 112.7 mm
Depth
Weight of the Remote Control Unit:
60 g (including battery)
165 mm
Frequency Range:
MW: 531 kHz to 1602 kHz
LW: 153 kHz to 279 kHz
Usable Sensitivity:
MW: 28 dBPV
LW: 34 dBPV
Bluetooth
Specification: Bluetooth Ver. 1.2
Profile:
HFP (Hands-Free Profile)
OPP (Object Push Profile) Phone Book
A2DP (Advanced Audio Distribution Profile)
AVRCP (Audio/Video Remote Control Profile)
Send/Receive Sensitivity: Class 2
Audio Amplifier
Maximum power output:
200 W (50 W u 4)
Output Power:
4 u 27 W (DIN 45324, +B = 14.4 V)
Speaker impedance: 4 : (4 to 8 : allowable)
172 mm
178 mm
41.8 mm
AM Tuner
Owner’s manual
FM Tuner
50 mm
Note:
• Specifications comply with JEITA Standards.
• Specifications and design are subject to change
without notice for further improvement.
VZ709E
69
English
INSTALLATION AND WIRE
CONNECTION MANUAL
INSTALLATION
MANUAL
■ Contents
1. SAFETY PRECAUTIONS ...............................................................................................................70
2. BEFORE STARTING ......................................................................................................................72
3. PACKAGE CONTENTS..................................................................................................................72
4. GENERAL CAUTIONS ...................................................................................................................72
5. CAUTIONS ON INSTALLATION ....................................................................................................73
6. INSTALLING THE MAIN UNIT .......................................................................................................74
7. REMOVING THE MAIN UNIT.........................................................................................................76
8. CAUTIONS ON WIRING.................................................................................................................76
9. WIRE CONNECTION .....................................................................................................................77
10. SAMPLE SYSTEM..........................................................................................................................80
1. SAFETY PRECAUTIONS
The Installation and Wire Connection Manual is intended for authorized Clarion dealers. Due to the
complexity of the vehicle’s wiring and components, it is recommended an authorized Clarion dealer
perform the installation. For the location of nearest authorized Clarion dealer, please visit:
www.clarion.com
For your safety, the Owner’s Manual should be read thoroughly to familiarize yourself with controls and
functionality.
Symbol Identification
This manual uses symbols and icons to indicate
safety precautions and concerns during the
installation procedure. Be sure to carefully read
and understand each precaution prior to
beginning the installation.
WARNING
This symbol is intended to alert the user to
the presence of important operating
instructions. Failure to heed the
instructions may result in severe injury or
death.
Before Use
WARNING
• Confirm the battery voltage of the vehicle
to be installed. This unit is designed only
for vehicles with DC 12V power supply.
• Disconnect the negative terminal of the
battery before connecting wires,
otherwise an electric shock, injury by
short circuit may occur.
CAUTION
CAUTION
This symbol is intended to alert the user to
the presence of important operating
instructions. Failure to heed the instructions
can result in injury or material damage.
70
VZ709E
Car battery
Installation Precautions
CAUTION
CAUTION
• Do not install the system in the locations
described below. This may cause a fire,
accident or electrical shock:
A location exposed to rain or dust.
A location interfering with the driver’s
visual range or operation of the vehicle.
An unstable location, or where the system
may fall.
• Do not install this unit in a place exposed to
direct sunlight, heat or a place where the
vent holes or heat radiation holes are
covered.
• When you install the antenna, mount it in a
place where the elements of the antenna do
not protrude beyond the edge of the front,
back, left and right of the vehicle.
• If it comes in contact with pedestrians, it
may cause an accident.
Installation Notes
WARNING
• Please note the position of pipes, tanks
and electrical wirings before installing
the unit into the vehicle; failure in
avoiding these may cause a fire or
malfunction.
Connection Notes
WARNING
• Loom all cables according to the
instruction manual, so as not to hinder
operation.
• Wire the connecting cords/cables away
from high temperature areas. If the
coatings of the cables melt, it could
cause an accident/fire by a short circuit.
Take care when wiring in the engine
compartment.
• When wiring the connecting cables in a
vehicle with an airbag system, never feed
the cables through a place where it may
affect the operation of the airbag.
• An airbag not operating correctly in an
emergency may cause increased injury.
CAUTION
CAUTION
• Verify wires with a digital multi-meter prior
to making any connections. Many new
vehicles use multiplexed and/or low voltage
circuits that can be damaged if a test light
or logic probe is used.
• Connect cables appropriately. If a wrong
connection is made, this may cause a fire or
accident.
• When passing cables through the body of
the vehicle, use non-conductive grommets.
• If the coatings of the cables are worn out by
rubbing, this may cause an accident, fire or
a short circuit.
• After wiring cables, fix them with insulation
tape.
• Be sure to switch off the vehicle when
connecting or disconnecting cords to/from
the unit, otherwise an electric shock, injury
or accident may occur.
VZ709E
71
INSTALLATION
MANUAL
• When installing the unit to a vehicle with
an airbag system, never install it in a
place where it may affect the operation of
the airbag.
• Do not install this unit in the following
locations:
A location interfering with the driver’s
visual range or operation.
A location where the gear shift or brake
pedal are hindered.
A location where passengers are at risk.
An unstable location, or where the
system may fall.
CAUTION
• Use only the supplied parts.
• If unspecified parts are used, they may
cause damage.
• Any holes made in the body of the vehicle
should be sealed with a silicon adhesive.
• If exhaust fumes or water penetrates into
the vehicle, this may cause an accident.
• Fasten the bolts securely when installing
the unit. If the bolts are loose an accident or
malfunction could occur.
English
WARNING
CAUTION
English
2. BEFORE STARTING
INSTALLATION
MANUAL
1. This set is exclusively for use in cars with a
negative ground 12 V power supply.
2. Read these instructions carefully.
3. Be sure to disconnect the battery “-” terminal
before starting. This is to prevent short circuits
during installation. (Figure 1)
Car battery
Figure 1
3. PACKAGE CONTENTS
1 Main unit
2 Manuals
Owner’s manual & Installation manual
Warranty card
3 Power supply cord
4 Rca pin cord
5 Bag for accessories (No. 1)
Flat head screw (M5 u 8) ............................. 4
Sems hexagonal bolt (M5 u 8)..................... 5
Electro tap
Machine screw (M4 u 3) .............................. 4
6 Bag for accessories (No. 2)
Hook plate ................................................... 2
Cord clamp
Rubber cap .................................................. 1
Special Screw.............................................. 1
7 Bag for accessories (No. 3)
Rca cap ..................................................... 12
8 Universal mounting bracket
9 Remote control unit
0 Battery
(for remote control unit)
! Outer Escutcheon
@ DCP Case
4. GENERAL CAUTIONS
1. Do not open the case. There are no userserviceable parts inside. If you drop anything
into the unit during installation, consult your
dealer or an authorized Clarion service
center.
72
VZ709E
2. Use a soft, dry cloth to clean the case. Never
use a rough cloth, thinner, benzine, or alcohol,
etc. For tough dirt, apply a little cold or warm
water to a soft cloth and wipe off the dirt
gently.
Dashboard
5. Use the included screws for installation. Using
other screws can cause damage. (Figure 4)
Chassis
Damage
Max. 8 mm (M5 screw)
Figure 4
6. The source unit has mounting screw holes for
NISSAN (N marks) and TOYOTA (T marks)
vehicles. (Figure 5)
T
Gearshift lever
(check that it does
not touch the LCD.)
Chassis
INSTALLATION
MANUAL
1. Prepare all articles necessary for installing the
main unit before starting.
2. This model features a liquid crystal panel that
slides forward (shell loading system).
On some types of cars, the liquid crystal panel
may make contact with the dashboard or
gearshift lever, in which cause it cannot be
installed. Before installing, check that the unit
will not hamper operation of the gearshift lever
or obstruct your view before selecting the
installation location. (Figure 2)
N
T
Gearshift lever
Figure 2
3. Install the unit within 30q of the horizontal
plane. (Figure 3)
N
English
5. CAUTIONS ON INSTALLATION
T
N
Figure 5
Max. 30°
Figure 3
4. If you have to do any modification on the car
body, such as drilling holes, consult your car
dealer beforehand.
VZ709E
73
Universal Mount
INSTALLATION
MANUAL
Note:
• Some car models require special mounting kits for
proper installation. Consult your Clarion dealer for
details.
• Fasten the front stopper securely to prevent the
main unit from coming loose.
1. Place the universal mounting bracket into the
instrument panel, use a screwdriver to bend
each stopper of the universal mounting
bracket inward, then secure the stopper as
shown in Figure 6.
2. Wire as shown in Section 9 (see page 77).
3. Insert the main unit into the universal
mounting bracket until it locks.
4. Mount the outer escutcheon so that all the
hooks are locked.
• Console opening dimensions
Rear fastening hole (of vehicle)
182 mm
Hole
53 mm
English
6. INSTALLING THE MAIN UNIT
Instrument panel
Hole
Stoppers
Special Screw
Screwdriver
Rubber cap
Main Unit
Universal mounting bracket
Stoppers
Outer escutcheon
2-Spring
Note:
Set the outer escutcheon
so that its metallic part on
the back side fits the upper
edge of the main unit.
Figure 6
74
VZ709E
Fixed Mount (TOYOTA, NISSAN and other ISO/DIN equipped vehicles)
2-Screw
Engaging claw
MainUnit
2-Spring
Screwdriver
Figure 7
Mounting bracket *1
(1 pair for the left and right
sides)
4-Hexagonal screw *2
(M5 u 8)
*1
*1
*1
*1
MainUnit
*1
Pocket
Center Panel *3
*1
*1
*1
*4
Figure 8
Note:
*1 The parts and screws with this mark are used to install radio or included in the installation kit.
*2 The screws with this mark are enclosed in this set.
*3 In some cases, the center panel may require some modification (trimming, filling, etc.).
*4 If the hook on the installation bracket interferes with the unit, bend and flatten it with a nipper or a similar tool.
VZ709E
75
INSTALLATION
MANUAL
2. Secure the mounting brackets to the chassis
as shown in Figure 8. Holes are pre-tapped
for TOYOTA and NISSAN vehicles;
modification, such as drilling new holes, of the
mounting brackets may be required for other
models.
3. Wire as shown in Section 9 (see page 77).
4. Secure the unit in the dashboard, and then
reassemble the dashboard and the center
panel.
English
This unit is designed for fixed installation in the
dashboard.
If the vehicle is equipped with a factory-installed
radio, install the main unit with the parts and
screws marked (*2). (Figure 8)
If the vehicle is not equipped with a factoryinstalled radio, obtain an installation kit to install
the main unit in the following procedure.
1. Remove the screws from both side of the
main unit. Then, at either side, lift the leaf
spring until the engaging claws are released
from the holes, and slide the spring to the
direction of arrow to remove it. Repeat the
same for the other side to remove the springs
from the both sides. (Figure 7)
English
7. REMOVING THE MAIN UNIT
INSTALLATION
MANUAL
1. When the rear of the main unit has been
secured with the method shown in Figure 6
unfasten the special screw.
2. Remove the outer escutcheon.
3. Insert the hook plate between the spring and
the universal mounting bracket, fit tab B of
the spring into hole A of the hook plate, then
pull the main unit out by the hook plate. (Insert
both the right and left edges of the hook
plate.) (Figure 9)
Note:
• Keep the hook plate. You cannot remove the main
unit without disengaging the hook plate.
Instrument panel
Universal mounting bracket
2-Hook plate
Main
Unit
Spring
Outer escutcheon
A
B
Figure 9
8. CAUTIONS ON WIRING
1. Be sure to turn the power off before wiring.
2. Be particularly careful where you route the
wires.
Keep them well away from the engine, and
exhaust pipe, etc. Heat may damage the
wires.
3. If the fuse should blow, check to see if the
wiring is correct.
If a fuse is blown, replace it with a new one of
the same amperage rating as the original
(15A FUSE).
4. To replace the fuse, remove the old fuse of
the power supply cord and insert the new one.
(Figure 10)
Note:
• There are various types of fuse holder. Do not let
the battery side touch other metal parts.
caution
CAUTION
After the connection, fix the cord by a clamp
or insulation tape for protection.
Fuse (15A FUSE)
Fuse holder
Figure 10
76
VZ709E
English
9. WIRE CONNECTION
Note:
• Before installing, be sure to disconnect the negative - cable of the car battery.
• In the optional devices, the RCA Pin and the Connector cable are separately-sold items.
Radio antenna jack
Connector cable
(included in the iPod)
USB
terminal
RGB terminal
or
iPod with
video
Connect to
the AUX input
terminal.
Steering wheel
remote control
terminal
INSTALLATION
MANUAL
iPod
Connector
cable
(CCA-723)
CeNET
terminal
No connection
Refer to the following page.
Gray Red
Black
Front audio output
terminal
Right
Left
Rear audio output
terminal
Right
Left
Non fader output
terminal
White
Red
White
Purple Red
Gray
Right
Left
White
Yellow
Video output terminal
Green
Red
Right
Left
4-Channel Amplifier
Rear Monitor
(2Zone audio
output terminal)
White
Wireless
Headphone
Black Yellow
Video
White
Audio (left)
Red
Audio (right)
Black
Red
Yellow
AUX input
terminal
VTR etc.
Rear Vision Camera
terminal
Black
Microphone terminal of BT phone (Connects the optional microphone RCB-199.)
VZ709E
77
English
B-2
B-3
B-5
B-4
B-1
B-6
1
B-7
INSTALLATION
MANUAL
B-8
A-7
A-8
A-6
∗1
A-5
A-4
No.
3
Description
REAR RIGHT+
4
REAR RIGHTFRONT RIGHT+
5 ∗2
FRONT RIGHT-
2
FRONT LEFT+
FRONT LEFTREAR LEFT+
∗1
REAR LEFT+12 V MAIN POWER (*1)
Auto antenna
ILLUMINATION
+12 V ACCESSORY (*1)
GROUND
1
ISO CONNECTOR
2
Reverse gear terminal (Purple/White)
3
Spare terminal (Yellow)
4
Parking brake (Grass-green)
5
Remote terminal (Blue/White) (*2)
Note:
*1 In certain vehicles - Volkswagen/Opel/Vauxhall - it is necessary to exchange the accessory <<Red>> and
the main power <<Yellow>> connection, to avoid overload and loss of memory.
*2 When the unit is installed in a 1998 or later Volkswagen model, make sure to interrupt the <<Remote>>
output. Disconnect the <<blue/white>> wire and insulate the front ends of this cord. A breakdown may occur
if the cord is not disconnected, or front ends are not insulated.
See next page for how to connect the parking brake cord.
78
VZ709E
Parking brake lamp
+ cord to battery
Parking brake
Electro-tap
Parking brake
signal cord
●How to attach the electro-tap
1. Place the Parking brake cord at the stopper,
and fold it back in the direction of the arrow.
2. Pass the Parking brake signal cord through,
and fold it back in the direction of the arrow.
Parking brake
signal cord
Parking brake
signal cord
Parking brake cord
(Grass-green)
Stopper
Parking brake cord
(Grass-green)
Connecting the Accessories
●Connection to the Rear Vision Camera for vehicle
The Rear Vision Camera for vehicle can be connected to Rear Vision Camera terminal of the RCA pin
cord. For detailed information, refer to the instruction sheet or manual for the Rear Vision Camera.
Note:
• Be sure to connect the reverse gear cord to the vehicle’s relevant terminal.
• Connect the Rear Vision Camera to the RCA pin cord; if not, the screen turns black while the gearshift lever
is in the reverse gear position.
• The power supply box CAA185 (sold separately) is required for connection of the main unit and the Rear
Vision Camera.
●Navigation System
When using the NP509E:
Connect the CeNET Convert Box (CCB509) and the main unit via the CeNET and the RGB cables,
and then connect the CeNET Convert Box (CCB509) and the NP509E via the System cable.
When using the NAX983HD/NAX973HD/NAX963HD:
Connect the CeNET connector and the RGB terminal.
For detailed information, refer to the instruction manual of the Navigation System.
VZ709E
79
INSTALLATION
MANUAL
Note:
• Connecting the parking brake cord to lamp ground allows you to watch video images when the parking brake
is engaged.
• When the parking brake cord is not connected, the monitor will not display video images.
• If “AUDIO ONLY” appears on the screen just after turning on the ACC power of the car, release the parking
brake while confirming safety, and then engage the parking brake again.
English
●Connecting the parking brake cord
Connect the cord to parking brake lamp ground in the meter panel.
English
10. SAMPLE SYSTEM
INSTALLATION
MANUAL
iPod with
video
USB
terminal
RGB cable
(included in the
CCB509)
CeNET cable
(included in
the CCB509)
Black
Yellow
Connector cable
(CCA-723)
Red
Red
No connection
White
CeNET Convert Box
(CCB509)
RCA cable (sold
separately)
Front
speakers
Red
Gray
System cable
(included in the
NP509E)
White
Red
4-Channel
Amplifier
Black
Hide-away Navigation
(NP509E)
White
When using the
NAX983HD/NAX973HD/
NAX963HD
RGB cable
(included in the
NAX983HD/
NAX973HD/
NAX963HD)
CeNET cable
(included in the
NAX983HD/
NAX973HD/
NAX963HD)
HDD Navigation
(NAX983HD/
NAX973HD/
NAX963HD)
80
VZ709E
Gray
RCA cable (sold
separately)
Yellow
Red
Green
White
Rear Monitor
RCA cable (sold
separately)
Rear
speakers
CAUTIONS:
This appliance contains a laser system and is
classified as a “CLASS 1 LASER PRODUCT”.
To use this model properly, read this Owner’s
Manual carefully and keep this manual for
your future reference. In case of any trouble
with this player, please contact your nearest
“AUTHORIZED service station”. To prevent
direct exposure to the laser beam, do not try
to open the enclosure.
!CAUTION
USE OF CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED IN THE OWNER’S
MANUAL MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
ADVARSEL.
Denne mærking er anbragt udvendigt på
apparatet og indikerer, at apparatet arbejder
med laserstråler af klasse 1, hvilket betyder,
at der anvendes laserstråler af svageste
klasse, og at man ikke på apparatets yderside
kan blive udsat for utilladelig kraftig stråling.
APPARATET BØR KUN ÅBNES AF FAGFOLK
MED SÆRLIGT KENDSKAB TIL APPARATER
MED LASERSTRÅLER!
Indvendigt i apparatet er anbragt den her
gengivne advarselsmækning, som advarer
imod at foretage sådanne indgreb i apparatet,
at man kan komme til at udsaætte sig for
laserstråling.
OBS!
Apparaten innehåller laserkomponenten som
avger laserstrålning överstigande gränsen
för laserklass 1.
VAROITUS
Suojakoteloa si saa avata. Laite sisältää
laserdiodin, joka lähettää näkymätöntä
silmille vaarallista lasersäteilyä.
*VZ709E(001-cover)E
1
Dichiarazione di conformità:
Io mandatario nell' UE: Clarion Europa GmbH Hessenring 19-21, 64546 MörfeldenWalldorf, Germania
Dichiaro che il prodotto VZ709E è conforme al DM 28-08-1995 ottemperando alle
prescrizioni dei DM 25-06-1985 e DM 27-08-1987.
ministerial authorization FI DM 27-08-1987 n˚ of protocol: 0036543 date 08/05/09
Clarion Co., Ltd.
2009/6
All Rights Reserved. Copyright © 2009: Clarion Co., Ltd.
Printed in Slovakia / Imprimé en Slovaquie / Gedruckt in der Slowakei
Stampato in Slovacchia / Gedrukt in Slovakije / Impreso en Eslovaquia
Tryckt i Slovakien / Impresso na Eslováquia / Trykt i Slovakiet
QC-6833E
280-8753-01