Datalogic Falcon X3 User`s manual

Falcon™ X3
with Windows Mobile
www.mobile.datalogic.com
World wide Sales Network
available from: www.mobile.datalogic.com/contacts
Datalogic Mobile S.r.l.
Via S. Vitalino, 13
40012 Lippo di Calderara di Reno
Bologna - Italy
Telephone: (+39) 051-3147011
Fax: (+39) 051-3147561
User’s Manual
©2010-2011 Datalogic Mobile S.r.l.
11/11
Datalogic Mobile S.r.l.
Via S. Vitalino 13
40012 - Lippo di Calderara di Reno
Bologna - Italy
Falcon™ X3 with Windows Mobile 6.5 - User's Manual
Software Version: 1.00
Ed.: 11/2011
©2010-2011 Datalogic Mobile S.r.l. - ALL RIGHTS RESERVED - Protected to the fullest
extent under U.S. and international laws. • Copying, or altering of this document is
prohibited without express written consent from Datalogic [name of the owner of the
copyright].
Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in many
countries, including the U.S.A. and the E.U.
Falcon is a registered trademark of Datalogic Mobile Inc. in the U.S.A., Canada and the
E.U.
The Falcon logo is a trademark of Datalogic Mobile Inc.
All other brand and product names mentioned herein are for identification purposes only
and may be trademarks or registered trademarks of their respective owners.
CONTENTS
REFERENCES.................................................................................... V
Conventions .........................................................................................v
Reference Documentation ...................................................................v
Services and Support ...........................................................................v
GENERAL VIEW................................................................................ VI
1
1.1
1.2
1.3
1.4
1.4.1
1.5
INTRODUCTION................................................................................. 1
Falcon™ X3 Description ..................................................................... 1
Models Description.............................................................................. 3
Package Contents ............................................................................... 5
Inserting a Micro SD Card ................................................................... 6
Removing the Micro SD Card ............................................................. 7
Accessories......................................................................................... 8
2
2.1
2.2
2.3
BATTERIES AND MAINTENANCE .................................................... 9
Charging the Battery Pack .................................................................. 9
Replacing the Battery Pack ............................................................... 11
Cleaning the Mobile Computer.......................................................... 14
3
3.1
3.2
3.3
3.4
3.5
3.6
CONNECTIONS................................................................................ 15
USB Connection................................................................................ 15
Connection to USB peripherals ......................................................... 17
RS232 Connection ............................................................................ 19
WLAN Connection............................................................................. 20
WPAN Connection ............................................................................ 21
Wireless and Radio Frequencies Warnings ...................................... 22
4
4.1
4.1.1
4.1.2
4.2
4.3
4.3.1
4.3.2
4.4
4.4.1
4.4.2
4.4.3
4.5
4.5.1
4.5.2
4.6
4.6.1
4.7
4.7.1
4.7.2
4.7.3
USE AND FUNCTIONING ................................................................ 23
Startup............................................................................................... 23
Using the Stylus ................................................................................ 24
Touch Gestures................................................................................. 25
Windows Mobile Welcome Wizard.................................................... 26
Data Capture ..................................................................................... 27
Laser Data Capture ........................................................................... 28
Imager Data Capture......................................................................... 29
Description of the Keys ..................................................................... 31
Alphanumeric Keyboard .................................................................... 31
Numeric Keyboard............................................................................. 33
Resetting the Falcon X3.................................................................... 35
Status Indicators ............................................................................... 37
LED Status ........................................................................................ 37
Taskbar ............................................................................................. 38
Data Capture Configuration............................................................... 39
Configuration Control Panels ............................................................ 39
Control Panel .................................................................................... 44
Buttons .............................................................................................. 45
Wireless Manager ............................................................................. 47
Stylus Calibration .............................................................................. 48
iii
4.7.4
4.7.5
4.8
4.8.1
4.8.2
4.9
4.9.1
4.9.2
4.9.3
4.9.4
4.10
4.11
Volume Settings ................................................................................ 50
Summit Client Utility .......................................................................... 52
Windows Connections....................................................................... 55
Windows Mobile® Device Center...................................................... 55
Bluetooth® Manager Device Setup................................................... 57
Datalogic Firmware Utility.................................................................. 63
Retrieving a Firmware Image Update................................................ 63
Installing DFU on the Host PC .......................................................... 64
Updating the Firmware ...................................................................... 65
Restoring the Firmware ..................................................................... 66
Suspend Management ...................................................................... 68
Heat Management............................................................................. 69
5
5.1
5.2
TECHNICAL FEATURES ................................................................. 71
Technical Data .................................................................................. 71
Reading Diagrams ............................................................................ 75
6
TEST CODES ................................................................................... 78
SAFETY REGULATIONS ................................................................. 82
General Safety Rules ........................................................................ 82
Power Supply .................................................................................... 82
Laser Safety ...................................................................................... 83
LED Class ......................................................................................... 89
Radio Compliance ............................................................................. 89
FCC Compliance ............................................................................... 91
RF Exposure Information (SAR)........................................................ 92
Industry Canada Compliance ............................................................ 93
SAR Compliance ............................................................................... 94
Patents .............................................................................................. 94
WEEE Compliance............................................................................ 95
GLOSSARY ...................................................................................... 97
INDEX ............................................................................................. 101
iv
REFERENCES
CONVENTIONS
This manual uses the following conventions:
“User” refers to anyone using a Falcon X3 mobile computer.
“Mobile computer” and "Falcon X3" refer to the Falcon X3 mobile computer.
“You” refers to the System Administrator or Technical Support person using this
manual to install, configure, operate, maintain or troubleshoot an Falcon X3
mobile computer.
“Single Dock” refers to the Falcon X3 Single Slot Dock.
REFERENCE DOCUMENTATION
For further information regarding Falcon X3 refer to the SDK Help on-Line.
SERVICES AND SUPPORT
Datalogic provides several services as well as technical support through its
website.
Log on to www.mobile.datalogic.com and click on the links indicated for
further information including:
-
PRODUCTS
Search through the links to arrive at your product page where you can
download specific Manuals and Software & Utilities
-
-
SERVICES & SUPPORT
-
Datalogic Services
Agreements
-
Authorised Repair Centres
Warranty
Extensions
and
Maintenance
CONTACT US
E-mail form and listing of Datalogic Subsidiaries
v
GENERAL VIEW
C
H
B
J
A
K
G
I
E
F
M
L
D
A)
B)
C)
D)
E)
F)
G)
H)
Color Display*
ON/OFF Power Key
LEDs
Microphone
Front Scan Key
Keyboard
Stylus
Laser Safety Label
I)
J)
K)
L)
Loudspeaker
Color Camera and Flash
Product Label
Reset Key (under
battery)
M) Micro-SD Card Slot
(under battery)
*Remove protective film cover before use
N
O
N)
Data Capture/Laser Output Window O)
*
*Remove protective film cover before use
vi
Handylink™ Connector
(host/slave)
INTRODUCTION
1
1.1
1
INTRODUCTION
FALCON™ X3 DESCRIPTION
The new Datalogic Falcon X3 mobile computer delivers the ultimate in
ruggedness, ergonomics, computing and data capture technologies. Falcon X3
options provide a tailored solution for demanding environments needing real
time transaction visibility. The Falcon X3 delivers rugged construction, laser and
image data capture, along with real time communications in a product that is
effortless to develop for, deploy and manage.
Enterprises rely on accurate inventories to both plan and manage activities.
Three data capture options optimize the Falcon X3 to the application. A laser
scanner tackles high volume environments where speed is essential to
receiving and shipping operations. The imager captures linear, stacked and 2D
codes to reduce failed reads due to damaged and poor quality barcodes. An
optional camera takes pictures for the documentation of damaged or returned
goods. Datalogic’s patented Green Spot good read feedback reduces errors in
both noisy and quiet environments. For applications like cross docking where
bar codes can be close at hand or far away, an auto ranging laser offers an
aggressive scanning solution.
The parallel computer architecture of the Falcon X3 melds the strengths of an
XScale™ PXA310 microprocessor with a Cortex-M3 coprocessor. This
combination gears the device for real time information management. Memory of
256 MB RAM / 256 MB Flash accommodates multiple simultaneous
applications, for managing large databases or enabling off-line autonomy of
thick applications. A Micro SD Card Slot provides a simple way for users to
increase memory storage capacity as needed. The Falcon X3 tailors itself to the
information technology practices of the enterprise through either the Microsoft
Windows CE 6.0 or Microsoft Windows Mobile 6.5 operating system.
As information is collected the Falcon X3 turns to the task of communication via
a Summit IEEE 802.11 a/b/g radio. Complimented by a CCX v4 certification
from Cisco, the Falcon X3 provides infrastructure compatibility focused on
enterprise requirements for encrypted communication and seamless roaming.
Voice applications leverage the internet protocol connection for hands-free
voice picking and push to talk communications. Bluetooth® Wireless
Technology connects headsets, printers and other peripherals eliminating
cumbersome wires. An extensive accessory offering accommodates existing
installation needs for USB, RS232, modem or Ethernet communications.
The Falcon X3 comes in two form factors to tackle the differing scanning
intensities found in an enterprise. A pistol grip version with numeric keypad
tackles the high volume scan and quantity entry found at the receiving dock.
While a hand held with alpha numeric keypad better suits the lighter pick and
pack duty of preparing goods for shipment. The Falcon’s low weight balances a
large 3.5” display with a full size keyboard and a single piece 5000 mAh battery
into both of these packages.
1
1
FALCON™ X3
The Falcon X3 must do more than function for a full shift, it must survive daily
abuse and trauma. The new Falcon X3 survives drops from 6 feet (1.8 meter) to
concrete. Coupled with an IP64 sealing against water and dust allows the
Falcon X3 to literally take an industrial pounding. Plastic key caps with metal
snap dome actuation withstand not only the abusive environment but the heavy
use found in third party logistics centers, literally millions of cycles per year.
Falcon delivers Datalogic’s trademark ergonomics in a contoured package. An
arched pistol grip handle and ergonomic trigger make the rapid receiving of
goods comfortable through out the day. Falcon X3 numeric and alphanumeric
keyboards use a phone key layout placing numeric keys at the device top with
navigation, scan and enter keys. This highly functional layout places high use
keys at the user’s finger tips. Maximized key sizes drive additional user
efficiency with or with out gloves. A crystal clear QVGA display and back lit
keyboard make the Falcon X3 readable in dark back corners or full sunlight.
The Falcon X3 leverages Datalogic’s software development kit (SDK) for
creating applications. The Datalogic™ SDK provides a set of libraries allowing
easy application development using C++, .NET and Java programming
languages. Both MCL Collection and Wavelink® Studio™ offer additional
solutions to enable development. For terminal emulation environments available
tools include the Wavelink Industrial Browser™, Wavelink Terminal Emulation,
and Wavelink Speakeasy.
Wavelink Avalanche™ device management tools make the Falcon X3 an easy
device to both deploy and maintain. Datalogic Desktop, Configuration and
Firmware Utilities deliver unprecedented ability to customize and update device
configuration to the use environment or process. For small or remote
installations, Scan to Configure provides simple barcodes that anyone can use
to configure the Falcon X3. Wavelink Remote Control allows an administrator to
remotely diagnose and remedy both applications and device settings. For added
security the Falcon X3 can be implemented with Wavelink CE Secure and
Wavelink Certificate Manager
2
INTRODUCTION
1.2
1
MODELS DESCRIPTION
The Falcon X3™ is available in different models depending on the options it is
equipped with. All options are listed below:
•
•
•
•
communication: IEEE 802.11 a/b/g, Bluetooth
capture: high performance laser with green spot, 2D imager with green
spot, auto ranging laser, camera
form factor: hand held, pistol grip
keyboard: numeric, alphanumeric
For further details about the Falcon X3™ models refer to the web site:
http://www.mobile.datalogic.com.
For further information regarding Windows Mobile refer to the website:
http://www.microsoft.com/windowsmobile.
The currently available models are:
•
945200003
FalconX3 00A0HP-2F1-MEN1
Falcon X3 Hand held, 802.11 a/b/g CCX v4, Bluetooth v2, 256MB RAM,
256MB Flash, 52-key Alpha numeric, High Performance Laser w Green
Spot, Camera 3MP, Windows Mobile 6.5
•
945200007
FalconX3 00A0WI-2F1-MEN1
Falcon X3 Hand held, 802.11 a/b/g CCX v4, Bluetooth v2, 256MB RAM,
256MB Flash, 52-key Alpha numeric, Wide aspect imager w Green Spot,
Camera 3MP, Windows Mobile 6.5
•
945200008
FalconX3 00A0WI-2N0-MEN1
Falcon X3 Hand held, 802.11 a/b/g CCX v4, Bluetooth v2, 256MB RAM,
256MB Flash, 29-key Numeric, Wide aspect imager w Green Spot,
Windows Mobile 6.5
•
945200009
FalconX3 00A0HP-2N0-MEN1Falcon X3 Hand held,
802.11 a/b/g CCX v4, Bluetooth v2, 256MB RAM, 256MB Flash, 29-key
Numeric, High Performance Laser w Green Spot, Windows Mobile 6.5
•
945250000
FalconX3 00A0HP-3F1-MEN1
Falcon X3 Pistol grip, 802.11 a/b/g CCX v4, Bluetooth v2, 256MB RAM,
256MB Flash, 52-key Alpha numeric, High Performance Laser w Green
Spot, Camera 3MP, Windows Mobile 6.5
•
945250001
FalconX3 00A0WI-3F0-MEN1
Falcon X3 Pistol grip, 802.11 a/b/g CCX v4, Bluetooth v2, 256MB RAM,
256MB Flash, 52-key Alpha numeric, Wide aspect imager w Green Spot,
Windows Mobile 6.5
•
945250002
FalconX3 00A0XL-3F1-MEN1
Falcon X3 Pistol grip, 802.11 a/b/g CCX v4, Bluetooth v2, 256MB RAM,
256MB Flash, 52-key Alpha numeric, Auto ranging laser (XLR), Camera
3MP, Windows Mobile 6.5
3
1
FALCON™ X3
•
945250003
FalconX3 00A0HP-3N0-MEN1
Falcon X3 Pistol grip, 802.11 a/b/g CCX v4, Bluetooth v2, 256MB RAM,
256MB Flash, 29-key Numeric, High Performance Laser w Green Spot,
Windows Mobile 6.5
•
945250012
FalconX3 00A0XL-3N0-MEN1
Falcon X3 Pistol grip, 802.11 a/b/g CCX v4, Bluetooth v2, 256MB RAM,
256MB Flash, 29-key Numeric, Auto ranging laser (XLR), Windows Mobile
6.5
•
945250013
Falcon X3 00A0WI-3N0-MEN1
Falcon X3 Pistol grip, 802.11 a/b/g CCX v4, Bluetooth v2, 256MB RAM,
256MB Flash, 29-key Numeric, Wide aspect imager w Green Spot,
Windows Mobile 6.5
•
945250014
FalconX3 00A0WI-3F1-MEN1
Falcon X3 Pistol grip, 802.11 a/b/g CCX v4, Bluetooth v2, 256MB RAM,
256MB Flash, 52-key Alpha numeric, Wide aspect imager w Green Spot,
Camera 3MP, Windows Mobile 6.5
4
INTRODUCTION
1.3
1
PACKAGE CONTENTS
The Falcon X3™ package contains:
−
−
1 Falcon X3™ mobile computer
1 CD-ROM Datalogic SDK containing:
ƒ
Datalogic Applications (DCU, DFU, TCL, SDK)
ƒ
User Manuals
−
1 CD-ROM Getting Started Disk only for Windows Mobile
−
1 rechargeable battery pack
−
1 Windows Mobile End User License Agreement (depending on model)
−
1 Keypad overlay
Other packages will contain the accessories necessary for the Falcon X3™
connection to the host computer and to the network: the cradle, and /or one or
more connection cables.
Remove all the components from their packaging; check their integrity and
congruity with the packing documents.
Keep the original packaging for use when sending products
to the technical assistance center. Damage caused by
improper packaging is not covered under the warranty.
CAUTION
Rechargeable battery packs are not initially charged.
Therefore the initial operation to perform is to charge them.
See paragraph 2.1.
NOTE
5
FALCON™ X3
1
1.4
INSERTING A MICRO SD CARD
Falcon X3 provides the possibility to add a Micro SD memory storage card. To
access the Micro SD card slot and insert the card, proceed as follows:
1.
Turn off the Falcon X3.
2.
Press the latch release and lift the battery from the enclosure, as indicated
in the figure below:
3.
Open the Micro SD card slot by pulling up the locking plate:
4.
Insert the Micro SD card with the written part upward. Lock the card into
place by pushing the cardholder down:
a.
6
Replace battery
INTRODUCTION
1.4.1
1
Removing the Micro SD Card
To remove the Micro SD card, follow the steps above to access the SD area,
and remove it from its slot.
Follow proper ESD precautions to avoid damaging the SD.
Proper ESD precautions include, but are not limited to, working
on an ESD mat and ensuring that the operator is properly
grounded.
CAUTION Do not force the card. If you feel resistance, remove the card,
check the orientation, and reinsert it.
Do not use the Micro SD card slot for any other accessories.
7
FALCON™ X3
1
1.5
‰
‰
ACCESSORIES
Cradles
94A151125
Dock, Single Slot, FalconX3
94A151131
Dock, Powered Mobile, FalconX3
94A151133
Dock, Ethernet 4 Slot, FalconX3
94A151135
Charger, 4 Slot Dock, FalconX3
94A151137
Charger, 4 Slot Battery, FalconX3
Batteries
94ACC1386
‰
‰
Power Supply
94ACC1381
Power Supply, Dock, PWR Plug 2.1mm
94ACC1385
Power Supply, Charger, MBC and Dock
Cables
94A051970
‰
Battery, High Capacity, FalconX3
Cable, USB Handylink, Client
94A051971
Cable, USB Handylink, Host
94A051972
Cable, RS232 Handylink, Client
94A051973
Cable, RS232 Handylink, Host
94A051968
Cable, MicroUSB, Client
94A051969
Cable, MicroUSB, Host
Various
95ACC1056
Holster, FalconX3
94ACC1371
Module, Ethernet, Single Slot Dock
94ACC1372
Module, Modem, Single Slot Dock
94ACC1388
Softcase, FalconX3
94ACC1390
Handle Kit, Falcon X3
94ACC1391
Coverplate Kit, FalconX3
94ACC1392
Stylus, FalconX3 Pen with Tether (5pcs)
Use only a Datalogic Mobile-approved power supply and cables.
Use of an alternative power supply will invalidate any approval
given to this device and may be dangerous.
NOTE
8
BATTERIES AND MAINTENANCE
2
2
BATTERIES AND MAINTENANCE
Rechargeable backup batteries and battery packs are not
initially charged. Therefore the initial operation to perform is
to charge them. See below.
NOTE
Annual replacement of rechargeable battery pack avoids
possible risks or abnormalities and ensures maximum
performance.
CAUTION
2.1
CHARGING THE BATTERY PACK
The battery pack autonomy varies according to many factors,
such as the frequency of barcode scanning, RF usage, battery
life, storage, environmental conditions, etc.
NOTE
The battery icon on the Taskbar indicates when the battery pack is low.
It is possible to recharge the battery pack by using a Single Cradle or the Falcon
X3™ Multi Battery Charger.
Moreover recharging is possible by USB Direct connection with the host
computer, but with longer charging times and only if the mobile computer is off.
During the charging process the LED positioned at the left side of the display is
constant red. Once the charging process has been completed this LED is
constant green (see par. 4.5).
If the battery pack is removed from the mobile computer, it can be recharged by
inserting it into the rear slot of a Single Cradle or the Falcon X3™ Multi Battery
Charger.
Do not use the Falcon X3™ until batteries are charged for
minimum 4 hours.
CAUTION
9
2
FALCON™ X3
Even if the storage temperature range is wider, In order to
achieve the longest battery life, store the terminal and the
spare batteries between 20 to 30 ºC (68 to 86 ºF).
NOTE
The Batteries must be charged at a temperature ranging
from 0° to +40 °C (+32° to +104 °F).
For the GSM models the maximum recommended
temperature is + 35° C. At higher values the charging may
slow down.
The battery level may not be displayed correctly for some
minutes after the disconnection if the Falcon X3™ is
disconnected from power supply before the charging cycle
is completed.
NOTE
The Falcon X3™ could get warm during charging, this is
normal and does not mean a malfunction.
NOTE
10
BATTERIES AND MAINTENANCE
2.2
2
REPLACING THE BATTERY PACK
To correctly replace the battery pack, proceed as follows.
1.
Turn off the Falcon X3™.
2.
Press the latch release and lift battery from the enclosure as indicated in
the figure below:
3.
Install the new battery pack, first insert the top end, then the latch bottom
as indicated in the following figure.
11
FALCON™ X3
2
Installing, charging and/or any other action should be done by
authorized personnel and following this manual.
WARNING The battery pack may get hot, explode, ignite, and/or cause
serious injury if exposed to abusive conditions.
If the battery pack is replaced with an improper type, there is risk
of explosion.
Do not place the battery pack in or near a fire or heat; do not
place the battery pack in direct sunlight, or use or store the
battery pack inside unventilated areas in hot weather; do not
place the battery pack in microwave ovens, dryer, high pressure
containers, on induction cookware or similar device. Doing so
may cause the battery pack to generate heat, explode or ignite.
Using the battery pack in this manner may also result in a loss of
performance and a shortened life expectancy.
Use only a Datalogic Mobile approved power supply. The use of
an alternative power supply will void the product warranty, may
cause product damage and may cause heat, explode or ignite.
The area in which the units are charged should be clear of debris
and combustible materials or chemicals.
Do not use the battery pack of this terminal for power devices
different from this mobile computer.
Immediately discontinue use of the battery pack if, while using,
charging or storing the battery pack, the battery pack emits an
unusual smell, feels hot, changes colour or shape, or appears
abnormal in any other way.
Do not short-circuit the battery pack contacts connecting the
positive terminal and negative terminal. This might happen, for
example, when you carry a spare battery pack in your pocket
or purse; accidental short–circuiting can occur when a metallic
object such as a coin, clip, or pen causes direct connection of
the contacts of the battery pack (these look like metal strips on
the battery pack). Short–circuiting the terminals may damage
the battery pack or the connecting object
Do not apply voltages to the battery pack contacts.
Do not pierce the battery pack with nails, strike it with a hammer,
step on it or otherwise subject it to strong impacts or shocks.
Do not disassemble or modify (i.e. bend, crush or deform) the
battery pack. The battery pack contains safety and protection
devices, which, if damaged, may cause the battery pack to
generate heat, explode or ignite.
12
BATTERIES AND MAINTENANCE
2
In case of leakage of liquid from the battery, avoid contact with
liquid the skin or eyes. If the contact occurs, immediately wash
the affected area with water and consult a doctor.
WARNING
Do not solder directly onto the battery pack.
Do not expose the battery pack to liquids.
Avoid any knocks or excessive vibrations. If the device or the
battery is dropped, especially on a hard surface, you should take
it to the nearest Authorised Repair Centre for inspection before
continuing to use it.
Do not replace the battery pack when the device is turned on.
Do not remove or damage the battery pack’s label.
Do not use the battery pack if it is damaged in any part.
Battery pack usage by children should be supervised.
Collect and recycle waste batteries separately from the device
in comply with European Directive 2006/66/EC, 2002/95/EC,
2002/96/EC and subsequent modifications, US and China
regulatory and others laws and regulations about environment.
NOTE
In order to guarantee an adequate operating autonomy,
when replacing the battery pack the mobile computer
checks the battery energy level. If the battery is not
sufficiently charged, Falcon X3™ does not turn on (when
pressing the ON/OFF key).
In this case, either substitute the battery pack with a
charged one (sufficiently charged) or insert Falcon X3 into a
powered cradle or plug it into the direct power supply.
To achieve the best battery life, turn off the radios not in
use.
NOTE
13
FALCON™ X3
2
2.3
CLEANING THE MOBILE COMPUTER
Periodically clean the Falcon X3 with a slightly dampened cloth.
14
CONNECTIONS
3
3
CONNECTIONS
3.1
USB CONNECTION
You can use a Datalogic Handylink cable 94A051970 to directly connect the
Falcon X3 to a host computer to transfer data through the USB interface.
A
C
B
Key:
A)
Host Computer
B) 94A051970
Client Cable
Handylink
C)
Falcon X3
USB
Connection through the cable is compliant to 1.1 USBstandard.
NOTE
The Single Dock can be connected to the Host by means of a Micro-B USB
cord, such as Datalogic 94A051968 cable.
Once the host has been turned on, insert the Falcon X3 mobile computer into
the cradle.
A
C
B
D*
Key:
A)
C)
Falcon X3 Single Slot Dock
B) 94A051968 Micro USB Client D)
Cable
Host Computer
94ACC1381 Power Adapter
15
3
FALCON™ X3
Connection through the cradle is compliant to 1.1 USBstandard.
NOTE
The actual data transfer speed can be appreciably lower than the
maximum theoretical speed.
NOTE
16
CONNECTIONS
3.2
3
CONNECTION TO USB PERIPHERALS
To connect the Falcon X3 to a keyboard or a memory, connect the terminal to
the Datalogic 94A051969 cable or to the Datalogic 94A051971 cable (together
with a standard A to micro A USB cable).
For all these devices maximum current withdrawal must be below 100mA.
B
D
A
C
Key:
A) Keyboard with USB interface
C) 94A051969 Micro USB Host Cable/
94A051971 Handylink Micro USB Host
Cable
B) Falcon X3
D)
Standard A to Micro A USB Cable
B
D
A
C
Key:
A) USB hard drive/ external C) 94A051971 Handylink Micro USB
memory source
Host Cable
B) Falcon X3
D)
Standard A to Micro A USB Cable
Connect the Single Slot Dock to the peripheral by means of a Micro-A USB
cord, or use a Micro-A to Std-A receptacle USB adapter such as Datalogic
94A051969 (together with a standard USB cable if needed).
B
A
D
C
E
A)
USB Peripheral (memory)
D)
Standard A to Micro A USB Cable
B)
Falcon X3 Single Slot Dock
E)
94ACC1381 Power Adapter
C) 94A051969 Micro USB Host
Cable
17
FALCON™ X3
3
Falcon X3 works with most of mentioned USB peripherals. In any
case, we can’t guarantee good operations with all devices
available on market place.
NOTE
Connection is compliant to 1.1 USB standard.
NOTE
The actual data transfer speed can be appreciably lower than the
maximum theoretical speed.
NOTE
18
CONNECTIONS
3.3
3
RS232 CONNECTION
You can use the Datalogic 94A051972 cable to directly connect the Falcon X3
to a host computer to transfer data through the RS232 interface.
A
C
B
Key:
A)
Host Computer
B)
94A051972 Handylink Micro
RS232 Client Cable
C)
Falcon X3
The Single Slot Dock can be connected to the Host by means of a standard null
modem cable such as Datalogic 94A051020 CAB-427 for 9-pin connections.
Once the Host has been turned on, insert the Falcon X3 mobile computer into
the cradle.
A
C
B
D
Key:
A)
Host Computer
C)
Falcon X3 Single Slot Dock
B)
94A051020 CAB-427 RS232
Null Modem Cable
D)
94ACC1385 Power Adapter
19
FALCON™ X3
3
3.4
WLAN CONNECTION
Falcon X3 802.11 a/b/g radio models can communicate with the host using the
on-board radio frequency component and an Access Point connected to the
host computer.
To launch the radio configuration utility follow the following path:
Start > Summit > SCU to open the ‘Summit Client Utility’.
Detailed information about the applet for radio configuration can be found at
http://www.summitdatacom.com/SCU.htm .
20
CONNECTIONS
3.5
3
WPAN CONNECTION
Falcon X3 mobile computer models with Bluetooth® can communicate with
other Bluetooth® enabled devices, such as a printer, within a range of 10 m,
using the onboard Bluetooth® module.
B
A
Key:
A)
Falcon X3
B)
Bluetooth® printer
NOTE
NOTE
In order to avoid wasting energy, the Bluetooth® module is
off by default. If you need to have Bluetooth® working, the
module must be powered on using the Wireless
Communications applet (see par. 4.7.2), and perform the
Discovery procedure (see par. 4.8.2).
Suspending the terminal powers off the Bluetooth® radio and
drops the piconet (Bluetooth® connection). When the terminal
resumes, it takes approximately 10 seconds for the
Bluetooth® radio driver to re-initialize the radio.
Area coverage and Bluetooth® radio performance may vary,
due to environmental conditions or interference caused by
other devices (microwave ovens, radio transmitters, etc.), etc.
NOTE
21
FALCON™ X3
3
3.6
WIRELESS AND RADIO FREQUENCIES WARNINGS
WARNING
WARNING
22
Use only the supplied or an approved replacement
antenna. Unauthorized antennas, modifications or
attachments could damage the product and may violate
laws and regulations.
Most modern electronic equipment is shielded from RF
signals. However, certain electronic equipment may not
be shielded against the RF signals generated by Falcon
X3.
USE AND FUNCTIONING
4
4
USE AND FUNCTIONING
The use of the Falcon X3 depends on the application software loaded. However
there are several parameters that can be set and utilities that can be used to
perform some basic functions such as data capture, communications, file
management, etc.
4.1
STARTUP
The Falcon X3 turns on when the battery pack or the external supply is inserted.
After the battery pack is installed, use the [ON/OFF] key to turn the mobile
computer on and off.
As soon as the mobile computer is on, the Windows Mobile 6.5 desktop
configuration will appear on the screen. Wait a few seconds before starting any
activity so that the mobile computer completes its startup procedure.
Today Screen
Start Menu
Use the stylus (par. 4.1.1) as suggested to select icons and options.
The mobile computer goes into power-off (low power with display and keyboard
backlight off), when it is no longer used for more than a programmable timeout,
which is defined in the POWER applet of the Control Panel. In this mode it can
be awakened (resuming operation) by the [ON/OFF] key.
23
FALCON™ X3
4
The mobile computer can also be awakened or turned off by
the application program.
NOTE
4.1.1
Using the Stylus
The stylus selects items and enters information. The stylus functions like a
mouse.
Tap:
Touch the screen once with the stylus to open items and
select options
Drag:
Hold the stylus on the screen and drag across the screen to
select text and images. Drag in a list to select multiple items.
Tap-andhold:
Tap and hold the stylus on an item to see a list of actions
available for that item. On the pop-up menu that appears, tap
the action you want to perform.
To recalibrate the touch screen use the Stylus Applet (see par. 4.7.3)
Use only original Datalogic styluses supplied with the product
itself.
CAUTION
In
harsh
applications,
use
of
screen
protectors
should be taken into consideration, in order to extend the
touch screen operating life.
To prevent damage to the screen, do not use sharp devices or
any device other than the Datalogic Mobile-provided stylus.
Do not apply unnecessary high pressures on the screen.
For applications where an intensive use of the touch screen is
foreseen, please consider that touch screen components are
subject to progressive wear.
24
USE AND FUNCTIONING
4.1.2
4
Touch Gestures
Touch gestures describe gestures in which you use a finger or stylus to make a
short, directional movement over a control or object on the screen. Most
gestures are a single stroke. Windows Mobile supports five kinds of gestures.
Tap:
A tap represents the left click of a mouse.
Double Tap:
A double tap represents the left double click of a mouse.
Hold:
The user can press and hold on the screen to represent the
right click of a mouse.
Flick:
The user can move a finger across the screen to initiate perpixel scrolling, and if this movement is fast enough, scrolling
will continue after the finger is lifted.
Pan:
The user can press and hold on the screen and then drag the
finger in any direction to represent a mouse move event.
25
FALCON™ X3
4
4.2
WINDOWS MOBILE WELCOME WIZARD
In Windows Mobile, at the very first Falcon X3 startup, following a clean boot or
following a registry restore to default values, the mobile computer startup (see
par. 4.1 is preceded by the Welcome Wizard.
Welcome Wizard Screen
The Welcome Wizard allows the user to calibrate the touch screen (see par.
4.7.3) and to configure an email account and a password to protect the terminal.
Touch Screen Calibration Screen
26
USE AND FUNCTIONING
4.3
4
DATA CAPTURE
To capture data first of all tap Start > Settings > System > Decoding:
To configure and enable data capture parameters refer to par. 4.6.
27
FALCON™ X3
4
4.3.1
Laser Data Capture
To scan barcodes, point the Falcon X3 laser model onto the code from a
distance within the reading range while pressing the SCAN key.
The lighted band emitted by the laser must completely intercept the barcode as
shown in the figure below.
NO
NO
OK
OK
The XLR engine includes a pointer mode that projects a highly visible scan line
at longer ranges to make it easier to accurately target bar codes. The user
simply holds the trigger down until the aimer is on the appropriate code.
Releasing the trigger then initiates the bar code scan.
If the scan has taken place correctly:
-
the Good Read LED turns green until the user releases the trigger or scan
button;
if enabled, the Good Read beep is sounded;
if enabled, the Green Spot is projected on the bar code.
Remove the protective film cover over the Laser Output
Window before use.
NOTE
28
USE AND FUNCTIONING
4.3.2
4
Imager Data Capture
The Falcon X3 Imager captures a picture of the entire bar code. The omnidirectional scanning does not require that the operator orient the bar code to
align with the scan pattern.
To read a 1D or 2D code, simply point the Falcon X3 Imager model onto the
code and press the SCAN Key.
The Falcon X3 Imager uses an intelligent aiming system pattern, similar to
those on cameras, indicating the field of view, which should be positioned over
the code:
Aiming System
29
FALCON™ X3
4
If the aiming system pattern is centered over the entire symbology as shown in
the following figure, either wait for the timeout or release the Scan key to
capture the image.
Linear barcode
2D Matrix symbol
ÌBX3ÉÎ
Relative Size and Location of Aiming System Pattern
The field of view changes its size as you move the reader closer or farther away
from the code. The field of view indicated by the aiming system pattern will be
smaller when the Falcon X3 Imager is closer to the code and larger when it is
farther from the code.
Symbologies with smaller bars or elements (mil size) should be read closer to
the unit. Symbologies with larger bars or elements (mil size) should be read
farther from the unit.
If the scan has taken place correctly:
-
the Good Read LED turns green until the user releases the trigger or scan
button;
-
if enabled, the Good Read beep is sounded;
-
If enabled, the Green Spot is projected on the bar code.
30
USE AND FUNCTIONING
4.4
4
DESCRIPTION OF THE KEYS
The Falcon X3 provides two different keyboards, an alphanumeric keyboard and
a numeric keyboard, having a total of respectively 52 and 29 keys.
4.4.1
Alphanumeric Keyboard
31
FALCON™ X3
4
Main Keys Function
KEY
FUNCTION
It starts barcode data capture.
They let you move forwards, backwards, upwards or
downwards within text fields, scroll through a Menu list
or browse among folder files.
Yellow modifier (toggle key): when pressed before a
standard key, it enables the character or function
printed in yellow above the key.
Blue modifier (one shot key): when pressed before a
standard key, it enables the character or function
printed in blue above the key.
It powers the Falcon X3 on or off. it is placed on the
upper left side of the terminal.
32
USE AND FUNCTIONING
4.4.2
4
Numeric Keyboard
33
FALCON™ X3
4
Main Keys Function
KEY
FUNCTION
It starts barcode data capture.
They let you move forwards, backwards, upwards or
downwards within text fields, scroll through a Menu
list or browse among folder files.
Yellow modifier (toggle key): when pressed before a
standard key, it enables the character or function
printed in yellow above the key.
Blue modifier (one shot key): when pressed before a
standard key, it enables the character or function
printed in blue above the key.
It powers the Falcon X3 ON or OFF. It is placed on
the upper left side of the terminal.
34
USE AND FUNCTIONING
4.4.3
4
Resetting the Falcon X3
There are several reset methods for the Falcon X3.
A warm boot terminates an unresponsive application and clears the working
RAM, but preserves the file system. Registry is restored from persistent memory
if available or returned to factory default.
A cold boot forces all applications to close reinitializing completely the system. It
clears the working RAM, but the file system is preserved. Registry is restored
from persistent memory.
A clean boot restores the Falcon X3 to a clean configuration: both the registry
and the file system returns to a clean status that conforms to factory default.
Warm Boot
To perform a warm boot, press and hold the following keys simultaneously:
+
+
Cold Boot
To perform a cold boot, do the following steps:
1.
Turn off the Falcon X3 by pressing the on-off key.
2.
Pull the battery latch down and remove the battery pack.
3.
Press and hold the scan button and then press the reset button.
4.
Insert the battery pack.
5.
Turn on the Falcon X3 by pressing the on-off key.
Clean Boot
To perform a clean boot, do the following steps:
1.
Perform a Cold Boot (see Cold Boot).
2.
Press and hold down the 0 and Esc keys simultaneously and then press
the on-off key:
+
A dialog box will appear asking for confirmation. Press the Enter Key.
35
FALCON™ X3
4
Registry
Warm Boot
Restored from flash
Cold Boot
Preserved
File System
Restored from flash
Preserved
36
Clean Boot
Clean configuration
(no user config)
Clean Installation
(no user files)
USE AND FUNCTIONING
4.5
4
STATUS INDICATORS
4.5.1
LED Status
The Falcon X3 provides three different LEDs signaling the mobile computer
status.
LED
STATUS
Charging Status
(left side)
Green
Constant once the charging
process has been completed (full
charge).
Red
Constant while charging.
Red blinking
Charge fault
Off
Keyboard in primary
Yellow solid
Yellow alternate key mode
Blue solid
Blue alternate key mode
Pink
CapsLock enabled
Red
Scanning LED is ON from the
time the user hits the scan button
(Trigger) until the bar code is
decoded (laser models)
Keyboard Status
(center)
Good Read
(right side)
Time-out (imager models)
Green
Scanning LED is ON, showing a
good decode.
37
FALCON™ X3
4
4.5.2
Taskbar
The Taskbar allows you to zoom the display. It also provides quick links to Wifi,
Activesync, Phone, Volume, Battery, and Clock settings.
ICONS
DESCRIPTION
Time and Battery Icons
It displays the system battery status.
It indicates that the battery is charging
Windows Mobile Taskbar
38
USE AND FUNCTIONING
4.6
4
DATA CAPTURE CONFIGURATION
You can configure the Falcon X3’s decoding options by tapping Start -> Settings
-> System -> Decoding.
There are two sections in the Decoding control panel, each containing
additional pages. There are six General Configuration pages and multiple
Barcode symbology pages.
4.6.1
Configuration Control Panels
Select the desired configuration from the options shown in the figure below, and
the other Decoding Properties figures on the following pages.
Select General or 1D Bar Code, then use the menu or tap the left and right
arrow keys to navigate the different pages of the Decoding utility. The menu
options will change to reflect the items most recently selected.
39
4
FALCON™ X3
Audio
From the Decoding menu, tap Configure > General > Audio. Use to set volume,
tone, duration, and number of various types of beeps.
General Options
From the Decoding menu, tap Configure > General > General Options. Select
from Label Programming Enable, Symbology IDs, Label Prefix, Label Suffix,
and Data Separator.
40
USE AND FUNCTIONING
4
Devices
From the Decoding menu, tap Configure > General > Devices. Use to enable or
disable the keyboard wedge for Barcode scanner.
Decoding Options
From the Decoding menu, tap Configure > General > Decoding Options. Select
a symbology to view or change the available properties settings.
Select Configure > General from the menu to view other configuration options.
41
4
FALCON™ X3
1D Barcode Symbology Pages
Use the drop-down menus from Configure > 1D Barcode, or tap the left and
right arrow keys to navigate the different pages of the barcode symbology
pages.
Select Configure > General from the menu to view other configuration options.
Each barcode symbology opens to its own page, as shown in the figure below.
Refer to the sample symbology control panels for examples of the types of fields
and options you can modify.
•
42
Codabar: Select Enable Checksum, Send Checksum, Send Start/Stop,
Convert to CLSI, Wide Gaps.
USE AND FUNCTIONING
4
Decoding Settings
Select from the Decoding Properties Settings menu to restore previous
configurations and/or other available default settings. Choose from:
•
Factory Defaults
•
Minimum Settings
•
Maximum Settings
•
Save (New Settings)
•
Revert to Saved Settings
The settings are saved when you tap OK.
When open, Decoding Properties acts as a simple barcode test tool that
provides the Data decoded and the Data Type of the barcode scanned.
43
FALCON™ X3
4
4.7
CONTROL PANEL
From the Start menu, tap Settings. The Control Panel is split into three sections:
Personal, System, Connections.
APPLET programs are displayed as icons; one icon corresponds to each
APPLET:
Windows Mobile Control Panel
44
USE AND FUNCTIONING
4.7.1
4
Buttons
From the Start menu, tap Settings > Personal > Buttons > Program Buttons.
On the Program Buttons tab, customize the program hardware buttons to
launch your most used applications. Under Select a button, tap the button you
want to assign a program to, and then select a program from Assign a program.
To configure the way up/down and the rest of keys control repeats, use the
Up/Down Control applet (Start > Settings > Personal > Buttons > Up/Down
Control).
45
4
FALCON™ X3
You can also select to wake up the terminal by the SCAN key (Start > Settings
> System > DL Buttons):
46
USE AND FUNCTIONING
4.7.2
4
Wireless Manager
The Wireless Manager applet provides power management of the 802.11 a/b/g
radio and Bluetooth® wireless module.
Open the Wireless Manager by tapping:
Start > Settings > Connections > Wireless Manager.
The following window will appear:
Wireless Manager Window
Selecting All, Wi-Fi or Bluetooth will turn on or off the respective radio(s).
47
FALCON™ X3
4
4.7.3
Stylus Calibration
You might need to recalibrate the touch screen (i.e. when you attempt to select
one item with the stylus, another item is erroneously selected).
To recalibrate the touch screen, complete the following steps:
1.
Select Start > Settings > System > Screen to open the Screen
Settings dialog as shown in the figure below:
2.
Tap Align Screen to open the Calibration screen shown in the figure
below.
Carefully press and briefly hold stylus on the center of the target. Repeat
as the target moves around the screen.
By completing the calibration procedure you implicitly accept the new
calibration settings.
New calibration settings are persistently saved in registry.
3.
4.
5.
48
USE AND FUNCTIONING
4
Startup stylus calibration
When starting the terminal, a Welcome Wizard (with Stylus Calibration) comes
up if valid calibration settings are not available. This happens in the following
circumstances:
1.
2.
3.
At the first startup of the terminal.
After restoring registry default settings and performing a boot.
After a Clean Boot.
49
FALCON™ X3
4
4.7.4
Volume Settings
From the Start Menu, select Settings > Sounds and Notifications:
Sounds and Notifications Window
The Audio applet allows to set the recording volumes of the main microphone
and of the headset microphone. Also, it allows to set the headset volume when
the user is listening to an audio file.
50
USE AND FUNCTIONING
4
To set the speaker volume during a call, click the
icon on the right top of the
Windows Mobile Start Menu. To set the front speaker or the headset speaker
volume, use the right bar or move the joystick up and down.
To set the rear speaker volume, use the left bar.
To set the Bluetooth® headset volume, tap:
Start > Settings > System > Bluetooth Manager > Connections and select the
headset. The following window will appear:
51
FALCON™ X3
4
4.7.5
Summit Client Utility
Wireless networking is controlled by a customized applet, the ‘Summit Client
Utility’ (SCU), specific to the radio.
To start the Summit Client Utility tap
Start > Summit > SCU
Or start SCU by tapping
Start > Settings > Connections, then select the right hand Wi-Fi icon.
52
USE AND FUNCTIONING
The SCU will open to the “Main” tab,
4
select the “Profile” tab
Information about the wireless network can be entered directly in the profile tab
or by pressing “Scan” when the desired network ESSID is in range.
At the “Scan” screen select the desired network and click “Configure”. Follow
the on screen instructions to setup security parameters for your network. For
more detailed settings specific to your installation please contact your wireless
network administrator. When finished, click “Commit” to save your settings.
53
4
FALCON™ X3
Return to the Main tab, if you have not previously selected “commit” you will be
prompted to save your changes.
At the “Main” tab change “Active Profile” to the one created in the “Profile” tab.
If you used the “Scan” button the desired profile will have the same name as the
ESSID.
Use the “Status” tab to check connectivity to the network.
Detailed information about the applet for radio configuration can be found at
http://www.summitdatacom.com/SCU.htm.
54
USE AND FUNCTIONING
4.8
4
WINDOWS CONNECTIONS
To connect the Falcon X3 to another device (i.e. Host PC) from Windows,
several programs are available. These programs require specific electrical
connections in order to function properly.
4.8.1
Windows Mobile® Device Center
Windows Mobile® Device Center gives you the possibility to connect your
desktop computer to your Falcon X3 and synchronize the information on them.
Synchronization compares the data on the Falcon X3 with that on the desktop
computer and updates both computers with the most recent information.
Windows Mobile Device Center is only compatible with Windows Vista and
Windows 7; if you run Windows XP or earlier, you have to download Microsoft
ActiveSync.
With Windows Mobile® Device Center" it is possible to:
-
Back up and restore Falcon X3 data.
-
Copy files between Falcon X3 and desktop computer.
-
Synchronize files by selecting a synchronization mode.
You can establish a connection to your Falcon X3 through the following
electrical interfaces:
‐
USB either directly or through the Single Dock
‐
Bluetooth® (see par. 4.8.2)
Synchronizing lets you transfer e-mail, contacts, appointments, tasks, Web
favorites, and media files from your computer to your device or from your device
to your computer. You must accept an update to Windows Mobile Device
Center (WMDC) on your computer before you can use WMDC to synchronize
the Falcon X3 with a host PC or with a Microsoft Exchange Server.
To establish a connection between the Falcon X3 and a host PC, start Windows
Mobile® Device Center, which is pre-installed on the mobile computer, and
follow the steps below:
1.
Connect the Falcon X3 to the host PC. Windows Mobile® Device Center
configures itself and then opens.
2.
On the licence agreement screen, click Accept.
3.
On the Windows Mobile Device Center’s Home screen, click Set up your
device.
55
FALCON™ X3
4
4.
Select the information types that you want to synchronize, then click Next.
5.
Enter a device name and click Set Up.
When you finish the setup wizard, Windows Mobile Device Center synchronizes
the mobile computer automatically. Microsoft® Office Outlook® emails and
other information will appear on your device after synchronisation.
NOTE
56
Visit the following Microsoft Web site for the latest in updates
and technical information:
http://www.microsoft.com/windowsmobile/enus/help/synchronize/device-synch.mspx
USE AND FUNCTIONING
4.8.2
4
Bluetooth® Manager Device Setup
The Bluetooth Device Properties icon will only be visible if
Bluetooth hardware has been installed on the unit.
NOTE
Before turning on Bluetooth®, ensure that the two devices are within close
range and that both Bluetooth-enabled devices are discoverable.
2.
Tap Start > Settings > System > Bluetooth Manager to open the
Bluetooth® control panel.
3.
Tap Settings. The Settings tab allows you to enable or disable the
Bluetooth radio and specify settings for Incoming Connections.
4.
Select or clear the “Enable Bluetooth Radio” check box:
57
4
5.
Tap Find Me if you want to make the Falcon X3 visible to other Bluetooth
devices for 60 seconds, allowing them to set up a connection.
NOTE
58
FALCON™ X3
By default, Bluetooth® is turned off. If you turn it on, and
then turn off your device, Bluetooth® also turns off. When
you turn on your device again, Bluetooth® turns on
automatically.
USE AND FUNCTIONING
4
To create a Bluetooth® partnership between your device and another device
that has Bluetooth® capabilities, ensure that the two devices are turned on,
discoverable, and within close range.
1.
Open the Bluetooth® control panel by tapping Start > Settings > System >
Bluetooth Manager. > Connections
2.
Search for available Bluetooth® Devices by tapping the button for the type
of device you want (Printer, Serial or All) or tap Discovery > Discover to
skip this step. The Falcon X3 will search for Bluetooth® Devices within
range.
NOTE
1.
If you attempt to set up a connection when the Bluetooth®
Radio is disabled, you will receive a message reminding
you that the radio is turned off, and asking you if you want
to turn it on. Tap Yes if you need to enable the Bluetooth®
Radio.
Once searching is complete, Bluetooth® Device Profiles will be displayed
in the Discovery tab. You can set up a connection to a device on the list, or
clear it from the list by tapping the Clear button:
59
4
FALCON™ X3
To set up a connection:
1.
60
Double tap the device you want to activate, or select and then tap
Connect. The resulting dialog will display services that are available on
the device:
USE AND FUNCTIONING
2.
4
Select the service you want to connect to. The following table shows the
icons that display for different types of service.
Icon
Service
Dialup Networking
Printer
File Transfer Protocol (FTP) Object Exchange (OBEX)
Object Push (OPP) Object Exchange (OBEX)
ActiveSync
Human Interface Device (HID) - Keyboard
Serial
Virtual Port allows you to specify the incoming port, which is used to
communicate serially with an incoming device just as if it were a physical COM
port. This option is available only if you have selected a Printer or Serial service.
You can also select Encrypt or Authenticate from the Bluetooth® control panel
to apply or modify those settings.
1.
To require Authentication, tap the checkbox, then tap OK.
2.
The Authentication Request dialog will then open, requesting that you
enter a PIN. Use the Input Panel to type in the PIN.
61
4
3.
FALCON™ X3
Tap OK to complete.
The dialog will also appear when an Authentication request is received from
another device.
Once you have set up a Pairing, you can view the settings by double-tapping its
name from the Connections tab. Tap the arrow to change the Virtual Port, or
Delete to remove the device pairing. Tap Sync to initiate a Sync (available only
if the service is an ActiveSync connection).
62
USE AND FUNCTIONING
4.9
4
DATALOGIC FIRMWARE UTILITY
The Datalogic devices are equipped with a field upgradeable firmware
mechanism. Firmware updates are available on the Datalogic Mobile website
(http://www.mobile.datalogic.com/). After you have downloaded the desired
update, there are several ways you can update the firmware on your device.
•
Use Wavelink Avalanche™ if you have multiple Datalogic mobile devices
to update. Refer to the Product CD included with your device for more
information.
•
If Wavelink Avalanche™ is not available or you have only a few Datalogic
Mobile devices to update, use the Datalogic Firmware Utility (DFU),
described below, to install or update the firmware using an ActiveSync
connection. Refer to "Installing & Setting Up Microsoft ActiveSync" for
more information.
DFU can also be used to restore the firmware onto a device that has become
corrupted, such as would happen if the device were powered down during an
ActiveSync firmware update (see par. 4.9.4).
The following sections provide procedures for the retrieval and installation of the
most current firmware image onto a Datalogic device.
4.9.1
Retrieving a Firmware Image Update
The following instructions use Internet Explorer to retrieve the most current
firmware image.
1.
Launch Internet Explorer on your PC and navigate to the Datalogic Mobile
website.
2.
Navigate to the Downloads section of the website.
3.
Select the file you want to download, then click Save to begin copying the
files to your local machine (or local network location).
63
FALCON™ X3
4
4.9.2
Installing DFU on the Host PC
The Datalogic Firmware Utility (DFU) provides administrators with a field
®
upgrade mechanism. You must have Microsoft ActiveSync already loaded and
running on the host PC to use DFU. Refer to "Installing & Setting Up Microsoft
ActiveSync" and "Using ActiveSync" for more information about ActiveSync.
Prior to installing, you must remove any previous versions
of DFU installed on the host PC.
NOTE
To install the Datalogic Firmware Utility, complete the following steps on the PC:
1.
Insert the CD ROM shipped with your device and click on the link to
Datalogic Firmware Utility.
OR
Go to the Datalogic Mobile website and download the most current version
of the Datalogic Firmware Utility. Unzip the file, then double-click to run
DFU_Seup. texe
Click OK to continue once you have removed previous versions of DFU.
2.
The Welcome to DFU Setup Program screen opens.
•
•
•
3.
64
Please exit all Windows applications before running this setup.
Click Cancel to quit Setup and close any programs you have running.
Click Next to continue the Setup.
Follow the onscreen instructions to complete the installation.
USE AND FUNCTIONING
4.9.3
4
Updating the Firmware
After copying the firmware image to the host PC (see par. 4.9.1) and installing
DFU (see par. 4.9.2), you can upgrade the firmware on your Datalogic device.
NOTE
1.
2.
The following steps require that you have already
established an ActiveSync connection between the host
computer and the Datalogic device. To establish an
ActiveSync connection with the device, refer to "Installing &
Setting Up Microsoft ActiveSync" and "Using ActiveSync",
for more information on ActiveSync.
Go to Start > Programs > DFU > Datalogic Firmware Utility.
Verify that ActiveSync is selected by clicking Communications >
ActiveSync.
3.
Click browse (...) and navigate to the location where you saved the
firmware file for your terminal.
4.
Select the current *.img file and click Open.
5.
Verify that your device is turned on. Insert the device into a powered dock
connected to the host computer.
6.
Click Update on DFU on the host PC.
65
FALCON™ X3
4
7.
DFU will compare the selected firmware image with the firmware already
loaded on the device; if the images are different, DFU will proceed to
update the firmware image on your device.
NOTE
8.
The following steps require that you have already
established an ActiveSync connection between the host
computer and the Datalogic device. To establish an
ActiveSync connection with the device, refer to "Installing &
Setting Up Microsoft ActiveSync" and "Using ActiveSync",
for more information on ActiveSync.
After the firmware of your device has been updated, you must perform a
warm reset of the device. Refer to the device user’s manual for reset
instructions.
4.9.4
Restoring the Firmware
If the firmware image on your device becomes corrupted, the device will beep
twice and show a blank screen when powered on. This can happen if a firmware
update is aborted, such as during a power loss or if the device is removed from
the Dock before completion of the procedure.
To reinstall the firmware, complete the following steps:
1.
On the PC, click Start > Programs > DFU > Datalogic Firmware Utility.
2.
From the Communications menu, select the communication mode you
are using to attach your dock to the PC - USB or Serial.
66
USE AND FUNCTIONING
3.
4
If you are using serial, then select the specific COM port to which the dock
is connected. DFU will display the COM ports available on your PC in a
drop down list.
4.
Click browse (...) and navigate to the file location.
5.
Select the current *.img file and click Open.
6.
Verify that the device is turned on. Insert the device into a powered dock
connected to the host computer.
7.
Click Update on DFU on the host PC.
8.
DFU will restore the firmware on your device.
NOTE
9.
Please be patient and do not remove the device from the
Dock during this procedure. The firmware image of the
device can take as long as:
• 12 minutes to download using a USB connection.
• 22 minutes to download using a serial connection with 115K
baud rate.
• 130 minutes to download using a serial connection with
19.2K baud rate.
After the firmware has been restored, your device will automatically reset.
67
FALCON™ X3
4
4.10 SUSPEND MANAGEMENT
Suspend Management allows the user to keep device features powered while
the device is off. The term "device off" here refers to a condition where the
display is off and the device appears unpowered. The device CPU may in fact
be powered on. The features managed by this feature are: Cellular Data/Voice
and GPS.
NOTE
The WiFi driver has been measured to consume about 50 µA
when left powered. As a result, WiFi will always be left powered
during suspend. This has the positive effect of substantially
reducing the time required for WiFi to fully resume when the
device is powered back on.
Normally, the device features will behave the same as today. This means when
the device is powered off, certain features (such as cellular communications)
will remain powered if enabled prior to the device powering off. The behavior of
each feature left powered during suspend is as follows:
•
Power is not removed from the feature.
•
It can act as a wakeup source for the CPU. When the CPU wakes up, the
device continues to appear "off", but the device driver on the CPU can
interact with the feature.
•
Depending on what activity takes place, any feature can optionally decide
to change the system power state from Suspend to On. This would appear
to the user as a wakeup event.
When the user powers off the device by pressing the power key, the behavior
begins similar to today:
•
•
The user is required to press the power key for at least 500 ms.
After this much time, the red suspend LED turns on to provide user
feedback that the power key has been recognized.
If the user releases the power key in the next 1.5 seconds, the system
completes the shutdown of the CPU and device features will remain powered. If
instead the user continues to hold down the power key for a total of at least two
seconds, then the following pop-up dialog will be displayed:
The user is given five seconds to respond. If the user selects "Yes", then the
device and all features are powered off. If the user selects "No", or does not
68
USE AND FUNCTIONING
4
respond within five seconds, the device will power off, but leave features as they
were.
4.11 HEAT MANAGEMENT
The purpose of heat management is to automatically reduce the heat generated
by the device features in order to allow battery charging to take place when
needed. It does not have a control panel UI to configure it. Instead, its behavior
can be configured through changes to the registry. This choice is made to
disguise the need by our current products for heat management when used in a
Powered Mobile Dock.
Heat management is only engaged when enabled and the device is attached to
a DC power source (dock or USB charger). When engaged, the heat manager
is allowed to disable the following features to reduce heat. The features are
listed in priority order. Items listed first will be disabled before others.
1.
Backlight
2.
WiFi
3.
Cellular Phone (Data and Voice)
4.
GPS
User feedback
When the heat manager has decided to disable one or more features, the
battery status page of the Power control panel applet will display the status
message "Charging Override" to reflect the fact that the heat manager is taking
action. In addition, when the heat manager first begins to disable a feature to
reduce heat, then the following pop-up message will be displayed:
If the user selects "OK", then heat management continues normally and begins
to disable features to reduce heat. If the user selects "Cancel", then no features
are disabled and heat management is disabled until the next change in profile
(device is attached again to a DC power source).
69
4
NOTE
70
FALCON™ X3
Device features that can be disabled by the heat management
function can still be manipulated by other software. This
decision is made to preserve the existing software layers (such
as the network stack) which we cannot change. As a result, it is
possible (but not likely) that unusual race conditions may result
from two pieces of software both trying to control a feature.
TECHNICAL FEATURES
5
5
TECHNICAL FEATURES
5.1
TECHNICAL DATA
Falcon X3 Common Features
PHYSICAL CHARACTERISTICS
DIMENSIONS
WEIGHT
Hand held: 225 x 88 x 55 mm, 64 x 40
mm at keyboard (8.9 x 3.5 x 2.2 in, 2.5 x
1.6 in)
Pistol grip: 225 x 88 x 168 mm (8.9 x 3.5 x
6.6 in)
Hand held: 626 g (22.08 oz)
Pistol Grip: 699 G (24.66 oz)
AUDIO
Loudspeaker; Microphone
LEDS
Three LEDs Decoding Status/ Keyboard
Status/ Charging Status
DISPLAY
Transflective TFT daylight readable color
display, 240 x 320 pixels, 3.5 inch
diagonal, 64 K colors, 200 nit backlight,
touch screen
KEYBOARD
Polycarbonate hard cap keyboards with
backlight
29 key numeric or 52 key alpha numeric
with discrete navigation
OPERATING TEMPERATURE*
-20ºC to 50ºC (14ºF to 122ºF)
STORAGE TEMPERATURE
DROP RESISTANCE
ENVIROMENTAL SEALING
-40ºC TO +70ºC (-40ºF TO 158ºF)
Withstands 18 drops from 1.8 m (6 ft)
onto concrete
IP64 standard for water and dust
resistance
* Shorter battery autonomy and slow display refreshes can be expected at low temperatures. Not
intended for long cold periods or rapid hot to cold transitions
71
FALCON™ X3
5
SYSTEM
OPERATING SYSTEM
Microsoft Windows CE 6.0 with Microsoft
WordPad and Internet Explorer 6.0
Microsoft Windows Mobile 6.5 with Mobile
tools: Outlook Mobile, Word Mobile, Excel
Mobile, PowerPoint Mobile, One Note Mobile
and Internet Explorer Mobile 6.0
MICROPROCESSOR
XScale™ PXA310 @ 624 MHz
COPROCESSOR
Cortex-M3, 32 bit @ 72 MHz
SYSTEM RAM MEMORY
256 MB
SYSTEM FLASH MEMORY
256 MB
MicroSD card slot compatible with SDHC
cards, user-accessible
Time and date stamping under software
control
Removable battery pack with rechargeable Liion batteries; 3.7 V 5000 mAh (18.5 Watt
hours)
EXPANSION SLOTS
REAL-TIME CLOCK
POWER SUPPLY*
COMMUNICATION
INTERFACES
LOCAL AREA
NETWORK (LAN)
PERSONAL AREA
NETWORK (PAN)
Main connector with USB Host, USB Client,
RS232 up to 115.2 Kbps, and audio headset
support
Summit IEEE 802.11 a/b/g
Frequency range: Country dependent, typically
2.4 GHz and 5.2 GHz
Cisco Compatible CCX v4 Security
Bluetooth® Wireless Technology IEEE 802.15
Class 2 with EDR
* Use only DL approved power adapters.
72
TECHNICAL FEATURES
5
CAPTURE
LASER CHARACTERISTICS
High Performance Laser (HPL) with
Green Spot, Auto Ranging Laser (XLR)
SCANNING RATE
40 ± 6 scan/sec
MINIMUM RESOLUTION
0.20 mm / 7.5 mils
DEPTH OF FIELD
HPL: 7 - 91 cm (3 - 36 inches) depending
on bar code density
XLR: Non reflective labels from 18 - 393
cm (7 to 154 in) depending on bar code
density; Reflective labels to 1376 cm (542
in)
All ranges dependent bar code size and
density.
Near range on reflective bar codes
determined by degree of reflectivity and
width of bar code.
GS1 Databar, EAN/UPC, Code 39, Code
32, 2/5 Codes, Codabar, Code 128,
EAN128, MSI, Code 93
BAR CODES
LASER CLASSIFICATION
VLD - Class 2/II EN 60825-1/CDHR
IMAGER CHARACTERISTICS
Wide Aspect Imager with Green Spot
SCANNING RATE
60 frames/sec maximum
MINIMUM RESOLUTION
Linear codes at 4 mils; 2D codes at 5 mils
DEPTH OF FIELD
5 to 40 cm (2 to 16 in), depending on bar
code size and density
BAR CODES
PDF417, Micro PDF, Datamatrix, QR
Code, Micro QR, Maxicode, Aztec,
Postnet, Planet, Japan Post, Aztec,
Australia Post, KIX Code, Royal Mail,
Intelligent Mail and UPU FICS, GS1
Databar, EAN/UPC, Code 32, Code 39,
2/5 Codes, Codabar, Code 128, EAN128,
MSI, Code 93, ISBT 128, Bookland EAN
and ISSN EAN
LASER CLASSIFICATION
CDRH/IEC Class II
LED CLASSIFICATION
IEC Class 1M
CAMERA CHARACTERISTICS
3 Mega pixel color with autofocus and
LED flash
IMAGE FORMATS
BMP, JPEG
73
FALCON™ X3
5
SOFTWARE
DEVELOPMENT
TERMINAL EMULATION
CONFIGURATION &
MAINTENANCE
SECURITY
VOICE
APPLICATIONS
74
Datalogic Windows SDK™
Wavelink® Studio™
MCL-Collection™
Java Virtual Machine
Wavelink® Industrial Browser™
Wavelink® Terminal Emulation™ prelicensed
Wavelink Avalanche® MC prelicensed
Wavelink Avalanche® SE prelicensed
Avalanche Remote Control™
Datalogic Firmware Utility
Datalogic Desktop Utility
Datalogic Configuration Utility
Wavelink CE Secure
Wavelink Certificate Manager
Vo-CE™ (voice recognition)
Wavelink® Communicator (push to talk)
Wavelink® SpeakEasy (voice recognition)
Pal Application Library
TECHNICAL FEATURES
5.2
5
READING DIAGRAMS
Auto Ranging Laser (XLR) 1D
Ranges - 1D codes:
7.5 mil: Code 39; 2.5:1 - 80% MRD: 2 - 22 (in) / 5.08 - 55.88 (cm)
10 mil: Code 39; 2.5:1 - 80% MRD: 4 - 34 (in) / 10.16 - 86.36 (cm)
15 mil: Code 39; 2.5:1 - 80% MRD: 5 - 71 (in) / 12.7 - 180.34 (cm)
20 mil: Code 39; 2.2:1 - 80% MRD: 5 - 96 (in) / 12.7 - 243.84 (cm)
55 mil: Code 39; 2.2:1 - 80% MRD: 15 - 180 (in) / 38.1 - 457.2 (cm)
70 mil reflective: Code 39;3:1 - 80% MRD: ∗ - 367 (in) / * - 932.18 (cm)
100 mil reflective: Code 39;3:1 - 80% MRD: * - 542 (in) / * - 1376.68 (cm)
∗
Near range on reflective bar codes determined by degree of reflectivity and
width of bar code
75
FALCON™ X3
5
High Performance Laser 1D
Ranges - 1D codes:
5.0 mil: Code 39; 2.5:1 - 80% MRD: 2.75 - 7 (in) / 6.98 - 17.78 (cm)
7.5 mil: Code 39; 2.5:1 - 80% MRD: 2.25 - 11 (in) / 5.72 - 27.94 (cm)
10 mil: Code 39; 2.5:1 - 80% MRD: 1.75 - 15.75 (in) / 4.45 - 40 (cm)
13 mil: 100% UPC - 80% MRD: 2 - 22 (in) / 5.08 - 55.888 (cm)
15 mil: Code 39; 2.5:1 - 80% MRD: 2 - 25 (in) / 5.08 - 63.50 (cm)
20 mil Code 39; 2.2:1 - 80% MRD: 2∗ - 30 (in) / 5.08* – 76.20 (cm)
40 mil Code 39; 2.2:1 - 80% MRD: 3.75* - 56 (in) / 9.53* – 142.24 (cm)
55 mil Code 39; 2.2:1 - 80% MRD: 5* - 66 (in) / 12.70* – 167.64 (cm)
∗
Near ranges on lower densities (not specified) are largely dependent upon the
width of the bar code and the scan angle
76
TECHNICAL FEATURES
5
Wide Aspect Imager 1D/2D
Ranges - 2D codes:
3.0 mil: Code 39 - 80% MRD: 2.7 – 4.2 (in) / 6.86 – 10.67 (cm)
5 mil: Code 39 - 80% MRD: 1.4 – 7.3 (in) / 3.56 – 18.54 (cm)
5 mil: PDF417 - 80% MRD: 2.8 – 4.5 (in) / 7.11 – 11.43 (cm)
6.67 mil: PDF417 - 80% MRD: 1.9 – 6.9 (in) / 4.83 – 17.53 (cm)
7.5 mil: Code 39 - 80% MRD: -∗ 9.9 (in) / -* 25.15 (cm)
10 mil PDF417 - 80% MRD: -* 9 (in) / -* 22.86 (cm)
13 mil UPC-A - 80% MRD: 1.6 – 12 (in) / 5.08 – 30.48 (cm)
15 mil PDF417; 2.2:1 - 80% MRD: -* 11.7 (in) / -* 29.72 (cm)
15 mil Data Matrix - 80% MRD: 2.3 – 11.2 (in) / 5.84 – 28.45 (cm)
20 mil Code 39 - 80% MRD: -* 19.7 (in) / -* 50.04 (cm)
∗
Near distances are FOV limited
77
FALCON™ X3
6
6
TEST CODES
High Density Codes
0.25 mm (10 mils)
Code 39
!17162H!
17162
2/5 Interleaved
Code 128
Ë"8NduÌ
0123456784
ÌtestwÎ
test
80%
EAN 13
x(0B2DE5*KKKKLM(
80%
EAN 8
(6450*TRMN(
78
TEST CODES
6
Medium Density Codes
0.38 mm (15 mils)
Code 39
Interleaved 2/5
!17162H!
17162
Ë"8NduÌ
0123456784
Code 128
ÌtestwÎ
test
100%
EAN 13
x(0B2DE5*KKKKLM(
100%
EAN 8
(6450*TRMN(
79
FALCON™ X3
6
Low Density Codes
0.50 mm (20 mils)
Code 39
!17162H!
17162
Interleaved 2/5
Ë"8NduÌ
0123456784
Code 128
ÌtestwÎ
test
120%
EAN 13
x(0B2DE5*KKKKLM(
120%
EAN 8
(6450*TRMN(
80
TEST CODES
6
2D Codes
Datamatrix ECC200
Example
Inverse
Datamatrix ECC200
Example
PDF417
Example
QR Code
Example
MAXICODE
Example
81
SAFETY REGULATIONS
NOTE
Read this manual carefully before performing any type of
connection to the Falcon X3 mobile computer.
The user is responsible for any damages caused by incorrect
use of the equipment or by inobservance of the indication
supplied in this manual.
GENERAL SAFETY RULES
−
Use only the components supplied by the manufacturer for the specific
Falcon X3 being used.
−
Do not attempt to disassemble the Falcon X3 mobile computer, as it does
not contain parts that can be repaired by the user. Any tampering will
invalidate the warranty.
−
When replacing the battery pack or at the end of the operative life of the
Falcon X3 mobile computer, disposal must be performed in compliance
with the laws in force.
−
Before using the devices and the battery packs, read par. 2.2.
−
Do not submerge the Falcon X3 in liquid products.
−
For further information, refer to this manual and to the Datalogic Mobile
web site: www.mobile.datalogic.com.
POWER SUPPLY
This device is intended to be connected to a UL Listed/CSA Certified computer
which supplies power directly to the Falcon X3 or else be supplied by a UL
Listed/CSA Certified Power Unit marked “Class 2” or LPS power source rated 5
V, 3.0 A, which supplies power directly to the Falcon X3 via the power
connector of the cable.
The package includes three international plug adapters. The adapters must be
plugged in the power supply before the power supply itself is plugged on the
wall outlet.
82
LASER SAFETY
The laser light is visible to the human eye and is emitted from the window
indicated in the figure.
This information applies to both laser models and the Falcon X3 Imager Aiming
System.
Laser output window
FalconX3
83
D
F
La luce laser è
visibile all'occhio
umano e viene
emessa dalla
finestra indicata
nella figura.
I
Die Laserstrahlung
ist für das
menschliche Auge
sichtbar und wird am
Strahlaustrittsfenster
ausgesendet (siehe
Bild).
Le rayon laser est
visible à l'oeil nu et il
est émis par la
fenêtre désignée sur
l'illustration dans la
figure.
La luz láser es
visible al ojo
humano y es
emitida por la
ventana indicada
en la figura.
LUCE LASER
NON FISSARE IL
FASCIO
APPARECCHIO
LASER DI CLASSE 2
MASSIMA POTENZA
DI USCITA: 1.23 mW
LUNGHEZZA D'ONDA
EMESSA: 650 nm
CONFORME A EN
60825-1 (2007)
LASERSTRAHLUNG
NICHT IN DER STRAHL
BLINKEN
PRODUKT DER
LASERKLASSE 2
MAXIMALE
AUSGANGLEISTUNG:
1.23 mW
WELLENLÄNGE: 650
nm
ENTSPR. EN 60825-1
(2007)
RAYON LASER
EVITER DE
REGARDER
LE RAYON
APPAREIL LASER DE
CLASSE 2
MAXIMUM PUISSANCE
DE SORTIE: 1.23 mW
LONGUER D'ONDE
EMISE: 650 nm
CONFORME A EN
60825-1 (2007)
RAYO LÁSER
NO MIRAR FIJO EL
RAYO
APARATO LÁSER DE
CLASE 2
MÁXIMA POTENCIA
DE SALIDA: 1.23 mW
LONGITUD DE ONDA
EMITIDA: 650 nm
CONFORME A EN
60825-1 (2007)
84
E
ENGLISH
The following information is provided to comply with the rules imposed by
international authorities and refers to the correct use of your mobile computer.
STANDARD LASER SAFETY REGULATIONS
This product conforms to the applicable requirements of both CDRH 21 CFR
1040 Subchapter J and EN 60825-1:2007 at the date of manufacture.
For installation, use and maintenance, it is not necessary to open the device.
CAUTION
Do not attempt to open or otherwise service any
components in the optics cavity. Opening or servicing
any part of the optics cavity by unauthorized personnel
may violate laser safety regulations. The optics system is
a factory only repair item.
Use of controls or adjustments or performance of
procedures other than those specified herein may result
in exposure to hazardous visible laser light.
CAUTION
The product utilizes a low-power laser diode. Although staring directly at the
laser beam momentarily causes no known biological damage, avoid staring at
the beam as one would with any very strong light source, such as the sun.
Avoid that the laser beam hits the eye of an observer, even through reflective
surfaces such as mirrors, etc.
Use of optical systems with the scanner will increase eye
hazard. Optical instruments include binoculars,
microscopes, eye glasses and magnifying glasses.
CAUTION
ITALIANO
Le seguenti informazioni vengono fornite dietro direttive delle autorità
internazionali e si riferiscono all’uso corretto del terminale.
NORMATIVE STANDARD PER LA SICUREZZA LASER
Questo prodotto risulta conforme alle normative vigenti sulla sicurezza laser alla
data di produzione: CDRH 21 CFR 1040 sezione J e EN 60825-1:2007.
Non si rende mai necessario aprire l’apparecchio per motivi di installazione,
utilizzo o manutenzione.
85
Non tentare di accedere allo scomparto contenete i
componenti ottici o di farne la manutenzione.
ATTENZIONE
L’apertura dello scomparto, o la manutenzione di
qualsiasi parte ottica da parte di personale non
autorizzato, potrebbe violare le norme della sicurezza. Il
sistema ottico può essere riparato solamente alla
fabbrica.
L'utilizzo di procedure o regolazioni differenti da quelle
descritte
nella
documentazione
può
provocare
un'esposizione pericolosa a luce laser visibile.
ATTENZIONE
Il prodotto utilizza un diodo laser a bassa potenza. Sebbene non siano noti
danni riportati dall’occhio umano in seguito ad una esposizione di breve durata,
evitare di fissare il raggio laser così come si eviterebbe qualsiasi altra sorgente
di luminosità intensa, ad esempio il sole. Evitare inoltre di dirigere il raggio laser
negli occhi di un osservatore, anche attraverso superfici riflettenti come gli
specchi.
ATTENZIONE
L’uso di strumenti ottici assieme allo scanner può
aumentare il pericolo di danno agli occhi. Tali strumenti
ottici includono cannocchiali, microscopi, occhiali e lenti
di ingrandimento.
DEUTSCH
Die folgenden Informationen stimmen mit den Sicherheitshinweisen überein, die
von internationalen Behörden auferlegt wurden, und sie beziehen sich auf den
korrekten Gebrauch vom Terminal.
NORM FÜR DIE LASERSICHERHEIT
Dies Produkt entspricht am Tag der Herstellung den gültigen EN 60825-1:2007
und CDRH 21 CFR 1040 Subchapter J Normen für die Lasersicherheit.
Es ist nicht notwendig, das Gerät wegen Betrieb oder Installations-, und
Wartungs-Arbeiten zu öffnen.
ACHTUNG
86
Unter keinen Umständen darf versucht werden, die
Komponenten im Optikhohlraum zu öffnen oder auf
irgendwelche andere Weise zu warten. Das Öffnen bzw.
Warten der Komponenten im Optikhohlraum durch
unbefugtes Personal verstößt gegen die LaserSicherheitsbestimmungen. Das Optiksystem darf nur
werkseitig repariert werden.
Jegliche Änderungen am Gerät sowie Vorgehensweisen,
die nicht in dieser Betriebsanleitung beschrieben werden,
können ein gefährliches Laserlicht verursachen.
ACHTUNG
Der Produkt benutzt eine Laserdiode. Obwohl zur Zeit keine Augenschäden von
kurzen Einstrahlungen bekannt sind, sollten Sie es vermeiden für längere Zeit in
den Laserstrahl zu schauen, genauso wenig wie in starke Lichtquellen (z.B. die
Sonne). Vermeiden Sie es, den Laserstrahl weder gegen die Augen eines
Beobachters, noch gegen reflektierende Oberflächen zu richten.
ACHTUNG
Die Verwendung von Optiksystemen mit diesem Scanner
erhöht die Gefahr einer Augenbeschädigung. Zu optischen
Instrumenten gehören unter anderem Ferngläser,
Mikroskope, Brillen und Vergrößerungsgläser.
FRANÇAIS
Les informations suivantes sont fournies selon les règles fixées par les autorités
internationales et se réfèrent à une correcte utilisation du terminal.
NORMES DE SECURITE LASER
Ce produit est conforme aux normes de sécurité laser en vigueur à sa date de
fabrication: CDRH 21 CFR 1040 sous-chapitre J et EN 60825-1:2007.
Il n’est pas nécessaire d’ouvrir l’appareil pour l’installation, l’utilisation ou
l’entretien.
ATTENTION
Ne pas essayer d’ouvrir ou de réparer les composants de
la cavité optique. L’ouverture de la cavité optique ou la
réparation de ses composants par une personne non
qualifiée peut entraîner le nonrespect des règles de
sécurité relatives au laser. Le système optique ne peut
être réparé qu’en usine.
L'utilisation de procédures ou réglages différents de ceux
donnés ici peut entraîner une dangereuse exposition à
lumière laser visible.
ATTENTION
Le produit utilise une diode laser. Aucun dommage aux yeux humains n’a été
constaté à la suite d’une exposition au rayon laser. Eviter de regarder fixement
le rayon, comme toute autre source lumineuse intense telle que le soleil. Eviter
aussi de diriger le rayon vers les yeux d’un observateur, même à travers des
surfaces réfléchissantes (miroirs, par exemple).
87
ATTENTION
L’utilisation d’instruments optiques avec le scanneur
augmente le danger pour les yeux. Les instruments
optiques comprennent les jumelles, les microscopes, les
lunettes et les verres grossissants.
ESPAÑOL
Las informaciones siguientes son presentadas en conformidad con las
disposiciones de las autoridades internacionales y se refieren al uso correcto
del terminal.
NORMATIVAS ESTÁNDAR PARA LA SEGURIDAD LÁSER
Este aparato resulta conforme a las normativas vigentes de seguridad láser a la
fecha de producción: CDRH 21 CFR 1040 Sección J y EN 60825-1:2007.
No es necesario abrir el aparato para la instalación, la utilización o la
manutención.
ATENCIÓN
No intente abrir o de ninguna manera dar servicio a ninguno
de los componentes del receptáculo óptico. Abrir o dar
servicio a las piezas del receptáculo óptico por parte del
personal no autorizado podría ser una violación a los
reglamentos de seguridad. El sistema óptico se puede
reparar en la fábrica solamente.
La utilización de procedimientos o regulaciones diferentes
de aquellas describidas en la documentación puede causar
una exposición peligrosa a la luz láser visible.
ATENCIÓN
El aparato utiliza un diodo láser a baja potencia. No son notorios daños a los
ojos humanos a consecuencia de una exposición de corta duración. Eviten de
mirar fijo el rayo láser así como evitarían cualquiera otra fuente de luminosidad
intensa, por ejemplo el sol. Además, eviten de dirigir el rayo láser hacia los ojos
de un observador, también a través de superficies reflectantes como los
espejos.
El uso de sistemas ópticos con el escáner aumentará el
riesgo de daños oculares. Los instrumentos ópticos
incluyen binoculares, microscopios, lentes y lupas.
ATENCIÓN
88
LED CLASS
According to EN60825-1:2007, the Falcon X3 1D models which use the green
spot LED are also CLASS 1 LED PRODUCTS.
APPARECCHIO LED CLASSE 1 IEC
PRODUKT LED KLASSE 1 IEC
PRODUIT LED DE CLASSE 1 IEC
PRODUCTO LED DE CLASE 1 IEC
According to EN60825-1:2007, the Falcon X3 2D models which use the
illuminator LED are also CLASS 1M LED PRODUCTS.
LED LIGHT
DO NOT VIEW DIRECTLY
WITH OPTICAL INSTRUMENTS
CLASS 1M LED PRODUCT
LUCE LED
NON OSSERVARE DIRETTAMENTE
CON STRUMENTI OTTICI
APPARECCHIO LED DI CLASSE 1M
LAMPE LED
NE PAS OBSERVER DIRECTEMENT
AVEC INSTRUMENTS OPTIQUES
APPAREIL LED DE CLASSE 1M
LUZ LED
NO OBSERVAR DIRECTAMENTE
CON INSTRUMENTOS ÓPTICOS.
PRODUCTO LED DE CLASE 1M
LED-LICHT
NICHT DIREKT MIT OPTISCHEN
INSTRUMENTEN BETRACHTEN.
GERÄTEKLASSE 1M.
RADIO COMPLIANCE
In radio systems configured with mobile computers and access points, the
frequencies to be used must be allowed by the spectrum authorities of the
specific country in which the installation takes place. Be absolutely sure that the
system frequencies are correctly set to be compliant with the spectrum
requirements of the country.
The Radio modules used in this product automatically adapt to the frequencies
set by the system and do not require any parameter settings.
This is a Class A product. In a domestic environment this product may cause
radio interferences in which case the user may be required to take adequate
measures.
1999/5/EEC R&TTE Compliance
89
Information for the User
ENGLISH
Contact the competent authority responsible for the management of radio
frequency devices of your country to verify any possible restrictions or licenses
required.
Refer to the web site http://europa.eu.int/comm/enterprise/rtte/spectr.htm for
further information.
ITALIANO
Prendi contatto con l'autorità competente per la gestione degli apparati a radio
frequenza del tuo paese, per verificare eventuali restrizioni o licenze. Ulteriori
informazioni sono disponibili sul sito:
http://europa.eu.int/comm/enterprise/rtte/spectr.htm.
FRANÇAIS
Contactez l'autorité compétente en la gestion des appareils à radio fréquence
de votre pays pour vérifier d'éventuelles restrictions ou licences. Pour tout
renseignement vous pouvez vous adresser au site web:
http://europa.eu.int/comm/enterprise/rtte/spectr.htm.
DEUTSCH
Wenden Sie sich an die für Radiofrequenzgeräte zuständige Behörde Ihres
Landes, um zu prüfen ob es Einschränkungen gibt, oder eine Lizenz
erforderlich ist. Weitere Informationen finden Sie auf der Web Seite:
http://europa.eu.int/comm/enterprise/rtte/spectr.htm.
ESPAÑOL
Contacta la autoridad competente para la gestión de los dispositivos de radio
frecuencia de tu país, para verificar cualesquiera restricciones o licencias
posibles requerida. Además se puede encontrar mas información en el sitio
Web:http://europa.eu.int/comm/enterprise/rtte/spectr.htm.
90
FCC COMPLIANCE
FCC Regulations:
•
•
•
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmfull interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
The User is cautioned that changes or modifications not expressly
approved by Datalogic for compliance could void the User’s authority to
operate the equipment.
The antenna(s) used for this transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.
91
RF EXPOSURE INFORMATION (SAR)
This model device meets the government’s requirements for exposure to radio
waves. This device is designed and manufactured not to exceed the emission
limits for exposure to radio frequency (RF) energy set by the Federal
Communications Commission of the U.S. Government.
The exposure standard for wireless devices employs a unit of measurement
known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC
is 1.6W/kg. *Tests for SAR are conducted using standard operating positions
accepted by the FCC with the device transmitting at its highest certified power
level in all tested frequency bands. Although the SAR is determined at the
highest certified power level, the actual SAR level of the device while operating
can be well below the maximum value. This is because the device is designed
to operate at multiple power levels so as to use only the power required to reach
the network. In general, the closer you are to a wireless base station antenna,
the lower the power output.
While there may be differences between the SAR levels of various devices and
at various positions, they all meet the government requirement.
The FCC has granted an Equipment Authorization for this model device with all
reported SAR levels evaluated as in compliance with the FCC RF exposure
guidelines. SAR information on this model device is on file with the FCC and
can be found under the Display Grant section of http://www.fcc.gov/oet/fccid
after searching on the below FCC IDs:
FCC ID: U4SFALX3
This device is compliant with SAR for general population /uncontrolled exposure
limits in ANSI/IEEE C95.1-1999 and had been tested in accordance with the
measurement methods and procedures specified in OET Bulletin 65
Supplement C.
92
INDUSTRY CANADA COMPLIANCE
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du
Canada.
Equipment is certified to the requirements of RSS-210 for 2.4-GHz per IEEE
802.11 (b)(g), IEEE 802.15 .
This device and its antenna(s) must not be co-located or operating in
conjunction with any other antenna or transmitter.
The County Code Selection feature is disabled for products marketed in the
US/Canada.
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. End users must follow the specific operating
instructions for satisfying RF exposure compliance. To maintain with IC RF
exposure compliance requirements please follow operation instruction as
documented in this manual.
To reduce the potential for harmful interference to co-channel mobile satellite
systems this device is limited to indoor use only.
Please note that high-power radars are allocated as primary users (meaning
they have priority) of the bands 5250-5350 MHz and 5650-5850 MHz and these
radars could cause interference and/or damage to the WiFi radio when
operating in these frequency bands.
93
SAR COMPLIANCE
This product has been tested and found to comply with the following standards:
-
OET BULLETIN 65 SUPPLEMENT C: evaluating compliance with FCC
guidelines for human exposure to radio frequency electromagnetic fields.
PATENTS
This product is covered by one or more of the following patents.
Design Pat.: EP 1,180,673; AU 329,643.
US Pat.: 5,198,649; 5,311,000; 5,440,110; 5,481,098; 5,493,108; 5,686,716;
5,992,740; 6,412,698; 6,415,978; 6,454,168; 6,478,224; 6,513,714; 6,561,427;
6,585,157; 6,808,114 B1; 6,997,385 B2; 7,108,170; 7,387,246 B2.
European Pat.: 789,315 B1; 1,128,315 B1; 1,396,811 B1; 1,413,971 B1.
Additional patents pending.
94
WEEE COMPLIANCE
Informazione degli utenti ai sensi della Direttiva Europea 2002/96/EC
L’apparecchiatura che riporta il simbolo del bidone barrato deve essere
smaltita, alla fine della sua vita utile, separatamente dai rifiuti urbani.
Smaltire l’apparecchiatura in conformità alla presente Direttiva consente di:
ƒ
evitare possibili conseguenze negative per l’ambiente e per la salute
umana che potrebbero invece essere causati dall’errato smaltimento
dello stesso;
ƒ
recuperare materiali di cui è composto al fine di ottenere un
importante risparmio di energia e di risorse.
Per maggiori dettagli sulle modalità di smaltimento, contattare il Fornitore dal
quale è stata acquistata l’apparecchiatura o consultare la sezione dedicata sul
sito www.mobile.datalogic.com.
Information for the user in accordance with the European Commission
Directive 2002/96/EC
At the end of its useful life, the product marked with the crossed out wheeled
wastebin must be disposed of separately from urban waste.
Disposing of the product according to this Directive:
ƒ
avoids potentially negative consequences to the environment and
human health which otherwise could be caused by incorrect disposal
ƒ
enables the recovery of materials to obtain a significant savings of
energy and resources.
For more detailed information about disposal, contact the supplier that provided
you with the product in question or consult the dedicated section at the website
www.mobile.datalogic.com.
Information
2002/96/EC
aux
utilisateurs
concernant
la
Directive
Européenne
Au terme de sa vie utile, le produit qui porte le symbole d'un caisson à ordures
barré ne doit pas être éliminé avec les déchets urbains.
Éliminer ce produit selon cette Directive permet de:
95
ƒ
ƒ
éviter les retombées négatives pour l'environnement et la santé
dérivant d'une élimination incorrecte
récupérer les matériaux dans le but d'une économie importante en
termes d'énergie et de ressources
Pour obtenir des informations complémentaires concernant l'élimination,
veuillez contacter le fournisseur auprès duquel vous avez acheté le produit ou
consulter la section consacrée au site Web www.mobile.datalogic.com.
Información para el usuario de accuerdo con la Directiva Europea
2002/96/CE
Al final de su vida útil, el producto marcado con un simbolo de contenedor de
bassura móvil tachado no debe eliminarse junto a los desechos urbanos.
Eliminar este producto de accuerdo con la Directiva permite de:
ƒ
evitar posibles consecuencias negativas para el medio ambiente y la
salud derivadas de una eliminación inadecuada
ƒ
recuperar los materiales obteniendo así un ahorro importante de
energía y recursos
Para obtener una información más detallada sobre la eliminación, por favor,
póngase en contacto con el proveedor donde lo compró o consultar la sección
dedicada en el Web site www.mobile.datalogic.com.
Benutzerinformation bezüglich Richtlinie 2002/96/EC der europäischen
Kommission
Am Ende des Gerätelebenszyklus darf das Produkt nicht über den städtischen
Hausmüll entsorgt werden. Eine entsprechende Mülltrennung ist erforderlich.
Beseitigung des Produkts entsprechend der Richtlinie:
ƒ
verhindert negative Auswirkungen für die Umwelt und die Gesundheit
der Menschen
ƒ
ermöglicht die Wiederverwendung der Materialien und spart somit
Energie und Resourcen
Weitere Informationen zu dieser Richtlinie erhalten sie von ihrem Lieferanten
über den sie das Produkt erworben haben, oder besuchen sie unsere Hompage
unter www.mobile.datalogic.com.
96
GLOSSARY
Access Point
A device that provides transparent access between Ethernet wired networks
and IEEE 802.11 interoperable radio-equipped mobile units. Hand-held mobile
computers, PDAs or other devices equipped with radio cards, communicate with
wired networks using Access Points (AP). The mobile unit (mobile computer)
may roam among the APs in the same subnet while maintaining a continuous,
seamless connection to the wired network.
Applet
Diminutive form of app (application), it refers to simple, single-function programs
that often ship with a larger product. Programs such as Windows' Calculator,
File Manager, and Notepad are examples of applets.
Barcode
A pattern of variable-width bars and spaces which represents numeric or
alphanumeric data in binary form. The general format of a barcode symbol
consists of a leading margin, start character, data or message character, check
character (if any), stop character, and trailing margin. Within this framework,
each recognizable symbology uses its own unique format.
Baud Rate
A measure for data transmission speed.
Bit
Binary digit. One bit is the basic unit of binary information. Generally, eight
consecutive bits compose one byte of data. The pattern of 0 and 1 values within
the byte determines its meaning.
Bluetooth®
A standard radio technology using a proprietary protocol. The onboard
Bluetooth® module in the mobile computer is compatible with the 1.1 protocol.
Byte
On an addressable boundary, eight adjacent binary digits (0 and 1) combined in
a pattern to represent a specific character or numeric value. Bits are numbered
from the right, 0 through 7, with bit 0 the low-order bit. One byte in memory can
be used to store one ASCII character.
Decode
To recognize a bar code symbology (e.g., Codabar, Code 128, Code 3 of 9,
UPC/EAN, etc.) and analyze the content of the bar code scanned.
Depth of Field (DOF)
The portion of a scene that appears acceptably sharp in the image. Although a
lens can precisely focus at only one distance, the decrease in sharpness is
97
gradual on each side of the focused distance, so that within the DOF, the
unsharpness is imperceptible under normal viewing conditions.
EDGE
Enhanced Data rates for GSM Evolution (EDGE) is a backward-compatible
digital mobile phone technology that allows improved data transmission rates,
as an extension on top of standard GSM. EDGE is considered a 3G radio
technology and is part of ITU's 3G definition.
EEPROM
Electrically Erasable Programmable Read-Only memory. An on-board nonvolatile memory chip.
Ethernet
The standard local area network (LAN) access method. A reference to "LAN,"
"LAN connection" or "network card" automatically implies Ethernet. Defined by
the IEEE as the 802.3 standard, Ethernet is used to connect computers in a
company or home network as well as to connect a single computer to a cable
modem or DSL modem for Internet access.
Firmware
Firmware is a software program or set of instructions programmed on a
hardware device. It provides the necessary instructions for how the device
communicates with the other computer hardware. Firmware is typically stored in
the flash ROM of a hardware device. While ROM is "read-only memory," flash
ROM can be erased and rewritten because it is actually a type of flash memory.
Flash Disk
Non-volatile memory for storing application and configuration files.
GSM
Global System for Mobile communication. It is a standard for digital cellular
communications, currently used in the 900 MHz and 1800 MHz bands.
Host
A computer that serves other mobile computers in a network, providing services
such as network control, database access, special programs, supervisory
programs, or programming languages.
WLAN
A Wireless Local Area Network links devices via a wireless distribution method
(typically spread-spectrum or OFDM radio), and usually provides a connection
through an access point to the wider internet. This gives users the mobility to
move around within a local coverage area and still be connected to the network.
98
IEEE 802.11
A set of standards carrying out wireless local area network (WLAN) computer
communication in the 2.4, 3.6 and 5 GHz frequency bands. They are created
and maintained by the IEEE LAN/MAN Standards Committee.
Liquid Crystal Display (LCD)
A display that uses liquid crystal sealed between two glass plates. The crystals
are excited by precise electrical charges, causing them to reflect light outside
according to their bias. They use little electricity and react relatively quickly.
They require external light to reflect their information to the user.
Light Emitting Diode (LED)
A low power electronic light source commonly used as an indicator light. It uses
less power than an incandescent light bulb but more than a Liquid Crystal
Display (LCD).
Null modem cable
RS-232 serial cable where the transmit and receive lines are crosslinked. In
some cables there are also handshake lines crosslinked. In many situations a
straight through serial cable is used, together with a null modem adapter. The
adapter contains the necessary crosslinks between the signals.
Pairing
A Bluetooth pairing occurs when two Bluetooth devices agree to communicate
with each other and establish a connection.
Piconet
A piconet is a Bluetooth PAN that links up to eight devices. Each piconet is
controlled by one master device, and up to seven slave devices at any one time.
Any device may be a member of more than one piconet, changing its
membership as a user moves from one area to another.
RAM
Random Access memory. Data in RAM can be accessed in random order, and
quickly written and read.
RF
Radio Frequency.
RTC
Real Time Clock.
TDMA
Time division multiple access (TDMA) is digital transmission technology that
allows a number of users to access a single radio-frequency (RF) channel
without interference by allocating unique time slots to each user within each
channel. The TDMA digital transmission scheme multiplexes three signals over
a single channel. The current TDMA standard for cellular divides a single
99
channel into six time slots, with each signal using two slots, providing a 3 to 1
gain in capacity over advanced mobile-phone service (AMPS). Each caller is
assigned a specific time slot for transmission.
USB
Universal Serial Bus. Type of serial bus that allows peripheral devices (disks,
modems, printers, digitizers, data gloves, etc.) to be easily connected to a
computer. A “plug-and-play” interface, it allows a device to be added without an
adapter card and without rebooting the computer (the latter is known as hotplugging). The USB standard, developed by several major computer and
telecommunications companies, supports data-transfer speeds up to 12
megabits per second, multiple data streams, and up to 127 peripherals.
WWAN
Stands for "Wide Area Network." It is similar to a Local Area Network (LAN), but
it is not limited to a single location and it uses Mobile telecommunication cellular
network technologies such as UMTS, GPRS, CDMA2000, GSM, CDPD,
Mobitex, HSDPA or 3G to transfer data. WWAN connectivity allows a user with
a laptop and a WWAN card to surf the web, check email, or connect to a Virtual
Private Network (VPN) from anywhere within the regional boundaries of cellular
service.
WPAN
A Wireless Personal Area Network is a personal area network - a network for
interconnecting devices centered around an individual person's workspace - in
which the connections are wireless. Typically, a wireless personal area network
uses some technology that permits communication within about 10 meters - in
other words, a very short range.
100
INDEX
A
Accessories; 7
M
Micro SD Card Insertion; 5
Models Description; 3
B
Batteries and Maintenance; 8
Bluetooth® Manager Device
Setup; 54
Buttons; 46
P
Package Contents; 4
Patents; 88
R
C
Charging the Batteries; 8
Cleaning the Mobile Computer; 13
Connections; 14
Connection to USB peripherals;
16
Control Panel; 45
Conventions; v
Radio Compliance; 83
Reading Diagram; 69
Reference Documentation; v
References; v
Replacing the Battery Pack; 10
Resetting the Falcon X3; 36
RF Exposure Information (SAR);
86
RS232 Connection; 18
D
Data Capture; 28
Data Capture Configuration; 40
Datalogic Firmware Utility; 60
Description of the Keys; 32
F
Falcon™ X3 Description; 1
FCC Compliance; 85
G
General View; vi
Glossary; 91
I
Imager Data Capture; 30
Industry Canada Compliance; 87
L
Laser Data Capture; 29
Laser Safety; 77
LED Class; 83
S
Safety Regulations; 76
SAR Compliance; 88
Services and Support; v
Startup; 24
Status Indicators; 38
Stylus Calibration; 48
T
Taskbar; 39
Technical Features; 65
Test Codes; 72
Touch Gestures; 26
U
USB Connection; 14
Using the Stylus; 25
V
Volume Settings; 50
W
WEEE Compliance; 89
Windows Connections; 52
101
Windows Mobile Welcome Wizard;
27
Windows Mobile® Device Center;
52
102
Wireless and Radio Frequencies
Warnings; 22
Wireless Communications; 47
WLAN Connection; 19
WPAN Connections; 21
Datalogic Mobile S.r.l.
Via S. Vitalino, 13
40012 - Lippo di Calderara
Bologna - Italy
10
dichiara che
declares that the
déclare que le
bescheinigt, daß das Gerät
declare que el
FALCON X3
modelli con funzionalità radio 802.11a/b/g+BT
models with 802.11a/b/g+BT radio feature
modèles avec 802.11a/b/g+BT radio intégrés
modelle mit 802.11a/b/g+BT radio-funktionalität
modelos con funcionalidad radio 802.11a/b/g+BT
sono conformi alle Direttive del Consiglio Europeo sottoelencate:
are in conformity with the requirements of the European Council Directives listed below
sont conformes aux spécifications des Directives de l’Union Européenne ci-dessous:
der nachstehend angeführten Direktiven des Europäischen Rats:
cumple con los requisitos de las Directivas del Consejo Europeo, según la lista siguiente:
1999/5/EEC R&TTE and 2004/108/EC EMC Directives
Questa dichiarazione è basata sulla conformità dei prodotti alle norme seguenti:
This declaration is based upon compliance of the products to the following standards:
Cette déclaration repose sur la conformité des produits aux normes suivantes:
Diese Erklärung basiert darauf, daß das Produkt den folgenden Normen entspricht:
Esta declaración se basa en el cumplimiento de los productos con la siguientes normas:
EN 55022: 2006
AMENDMENT A1:2007
(CLASS A ITE) :
INFORMATION TECHNOLOGY EQUIPMENT
RADIO DISTURBANCE CHARACTERISTICS
LIMITS AND METHODS OF MEASUREMENTS
EN 55024: 1998
AMENDMENT A1:2001
AMENDMENT A2:2003
INFORMATION TECHNOLOGY EQUIPMENT
IMMUNITY CHARACTERISTICS
LIMITS AND METHODS OF MEASUREMENT
ETSI EN 301 489-17 V1.2.1, AUGUST 2002
ELECTROMAGNETIC COMPATIBILITY AND RADIO SPECTRUM
MATTERS (ERM); ELECTROMAGNETIC COMPATIBILITY (EMC)
STANDARD FOR RADIO EQUIPMENT AND SERVICES; PART 17:
CONDITIONS
FOR
2,4GHZ
WIDEBAND
SPECIFIC
TRANSMISSION SYSTEMS AND 5GHZ HIGH PERFORMANCE
RLAN EQUIPMENT
AND MAY 2009 :
ETSI EN 300 328 V1.7.1, OCTOBER 2006 :
ELECTROMAGNETIC COMPATIBILITY AND RADIO SPECTRUM
MATTERS (ERM); WIDEBAND TRANSMISSION SYSTEMS; DATA
TRANSMISSION EQUIPMENT OPERATING IN THE 2,4GHZ ISM
BAND AND USING WIDE BAND MODULATION TECHNIQUES;
HARMONIZED EN COVERING ESSENTIAL REQUIREMENTS
UNDER ARTICLE 3.2 OF THE R&TTE DIRECTIVE
ETSI EN 301 893 V1.5.1, DECEMBER 2008
BROADBAND RADIO ACCESS NETWORKS (BRAN);5 GHZ
HIGH PERFORMANCE RLAN;HARMONIZED EN COVERING THE
ESSENTIAL REQUIREMENTS OF ARTICLE 3.2 OF THE R&TTE
DIRECTIVE
EN 60950-1:2006
AMENDMENT A11:2009
INFORMATION TECHNOLOGY EQUIPMENT - SAFETY BASIC RESTRICTIONS FOR RF EXPOSURE IN COUNCIL
RECOMMENDATION 1999/519/EC
2006/95/EC Low Voltage Directive
EN 60950-1:2006
AMENDMENT A11:2009
INFORMATION TECHNOLOGY EQUIPMENT - SAFETY PART 1: GENERAL REQUIREMENTS
EN 60825-1:2007
LASER SAFETY
2006/66/EC and 2008/12/EC Battery Directives
Batteries and accumulators and waste batteries and accumulators
2002/95/EC RoHS Directive
Restriction of the use of certain hazardous substances in electrical and electronic equipment
2002/96/EC WEEE Directive
Lippo di Calderara, July 2, 2010
Paola Chientaroli
Quality Assurance Manager
Falcon™ X3
with Windows Mobile
www.mobile.datalogic.com
World wide Sales Network
available from: www.mobile.datalogic.com/contacts
Datalogic Mobile S.r.l.
Via S. Vitalino, 13
40012 Lippo di Calderara di Reno
Bologna - Italy
Telephone: (+39) 051-3147011
Fax: (+39) 051-3147561
User’s Manual
©2010-2011 Datalogic Mobile S.r.l.
11/11