Digital Monitoring Products XR2500F Installation guide

INSTALLATION GUIDE
XR2500F ADDRESSABLE
FIRE ALARM CONTROL PANEL
MODEL XR2500F
COMMAND PROCESSOR
INSTALLATION GUIDE
FCC NOTICE
This equipment generates and uses radio frequency energy and, if not installed and used properly in strict accordance
with the manufacturer’s instructions, may cause interference with radio and television reception. It has been type tested
and found to comply with the limits for a Class A computing device in accordance with the specification in Subpart J
of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential
installation. If this equipment does cause interference to radio or television reception, which can be determined by
turning the equipment off and on, the installer is encouraged to try to correct the interference by one or more of the
following measures:
Reorient the receiving antenna
Relocate the computer with respect to the receiver
Move the computer away from the receiver
Plug the compute into a different outlet so that computer and receiver are on different branch circuits
If necessary, the installer should consult the dealer or an experienced radio/television technician for additional suggestions.
The installer may find the following booklet, prepared by the Federal Communications Commission, helpful:
“How to identify and Resolve Radio-TV Interference Problems.”
This booklet is available from the U.S. Government Printing Office, Washington D.C. 20402
Stock No. 004-000-00345-4
© 2004-2005 Digital Monitoring Products, Inc.
Information furnished by DMP is believed to be accurate and reliable.
This information is subject to change without notice.
TABLE OF CONTENTS
Revisions to This Document
Introduction
1.1
1.2
1.3
1.4
1.5
1.6
Overview ...................................................................................................... 1
System Components ...................................................................................... 1
Power Specifications ...................................................................................... 1
Before You Begin ........................................................................................... 1
About this Guide............................................................................................ 1
How to use this Guide.................................................................................... 1
Mounting
2.1
2.2
2.3
2.4
2.5
2.6
Mounting the Enclosure.................................................................................. 2
Surface Mounting .......................................................................................... 2
Flush Mounting.............................................................................................. 2
Fire Command Center LCD Keyboard............................................................... 2
Metal Backplate ............................................................................................. 2
Wiring Diagram ............................................................................................. 3
AC Connection
3.1
3.2
3.3
3.4
Transformers and AC Power Connection .......................................................... 4
28 VAC Transformer....................................................................................... 4
16 VAC Transformer ...................................................................................... 4
Earth Ground from the XR2500F Panel ........................................................... 4
Secondary Power Supply
4.1
4.2
4.3
Description.................................................................................................... 5
Battery Connection to XR2500F Command Processor panel............................... 5
Battery Connection to the 504-24 Power Supply............................................... 5
Two 866 NAC Modules
5.1
5.2
5.3
5.4
Description.................................................................................................... 6
Connection.................................................................................................... 6
Bell Silence/Bell Trouble ................................................................................. 6
Notification Appliances .................................................................................. 7
LX-Bus™ Operation
6.1
6.2
6.3
6.4
6.5
Description.................................................................................................... 8
XR2500F On-board LX-Bus ............................................................................ 8
LX-Bus 481 Zone Expansion Interface Card...................................................... 8
Installing the 481 Card................................................................................... 8
LX-Bus™ Expansion Capability ........................................................................ 8
893A Dual Phone Line Module
7.1
7.2
7.3
7.4
7.5
7.6
7.7
7.8
7.9
7.10
Description.................................................................................................... 9
Connection.................................................................................................... 9
Jumper Settings ............................................................................................ 9
Digital Dialer ................................................................................................. 9
Phone Line Monitor........................................................................................ 9
Processor Fail Buzzer ..................................................................................... 9
J10 893A Connector....................................................................................... 9
Ground start.................................................................................................. 9
Notification ................................................................................................. 10
FCC Registration ......................................................................................... 10
504-24 Power Supply
8.1
8.2
8.3
8.4
8.5
8.6
XR2500F Installation Guide
Description.................................................................................................. 11
LEDs .......................................................................................................... 11
504-24 Condition Chart ................................................................................ 11
504-24 UL Listings ....................................................................................... 11
24 VDC NAC Standby Battery Calculations ..................................................... 11
Connection.................................................................................................. 12
Digital Monitoring Products
i
TABLE OF CONTENTS
Interconnect Wiring Harness
9.1
Interconnect Harness................................................................................... 12
Fire Command Center
10.1
10.2
10.3
Description.................................................................................................. 13
Connection.................................................................................................. 13
Remote Fire Command Center ...................................................................... 13
Panel Features
11.1
11.2
11.3
11.4
Description.................................................................................................. 14
Connection ................................................................................................. 14
Relays ....................................................................................................... 14
Zone Reference ........................................................................................... 14
XR2500F Product Specifications
12.1
12.2
12.3
12.4
12.5
12.6
Power Supply .............................................................................................. 15
Communication ........................................................................................... 15
Panel Zones ................................................................................................ 15
Keypad Bus ................................................................................................. 15
LX-Bus™ ..................................................................................................... 15
Outputs ...................................................................................................... 15
Expansion
13.1
13.2
Zone Expansion ........................................................................................... 16
Output Expansion ........................................................................................ 16
Accessory Devices
14.1
14.2
14.3
14.4
14.5
Wiring Diagram ........................................................................................... 17
Lightning Protection..................................................................................... 17
Accessory Devices ....................................................................................... 18
Mounting Keypads and Zone Expansion Modules............................................ 19
Connecting LX-Bus and Keypad Bus Devices .................................................. 19
Battery Information
15.1
15.2
15.3
15.4
15.5
15.6
15.7
15.8
Battery Only Restart .................................................................................... 20
Battery Replacement Period ......................................................................... 20
Discharge/Recharge..................................................................................... 20
Battery Supervision...................................................................................... 20
Battery Cutoff.............................................................................................. 20
XR2500F Power Requirements ...................................................................... 20
XR2500F Standby Battery Calculations .......................................................... 21
Standby Battery Selection ............................................................................ 23
Bell Output
16.1
Terminals 5 and 6 ........................................................................................ 24
Keypad Bus
17.1
17.2
17.3
17.4
17.5
17.6
17.7
Description.................................................................................................. 24
Terminal 7 - RED ......................................................................................... 24
Terminal 8 - YELLOW ................................................................................... 24
Terminal 9 - GREEN ..................................................................................... 24
Terminal 10 - BLACK .................................................................................... 24
J8 Programming Connection ......................................................................... 24
OVC LED..................................................................................................... 24
Smoke and Glassbreak Detector Output
18.1
18.2
Terminals 11 and 12 .................................................................................... 25
Current Rating............................................................................................. 25
Digital Monitoring Products
ii
XR2500F Installation Guide
TABLE OF CONTENTS
Powered Zones for 2-Wire Smoke Detectors
19.1
19.2
Terminals 25–26 and 27–28 ......................................................................... 25
Compatible 2-Wire Smoke Detector Chart...................................................... 26
Protection Zones
20.1
20.2
20.3
20.4
Terminals 13–24 .......................................................................................... 27
Operational Parameters................................................................................ 27
Zone Response Time.................................................................................... 27
Keyswitch Arming Zone ................................................................................ 27
Dry Contact Relay Outputs
21.1
21.2
21.3
Description.................................................................................................. 28
Contact Rating ............................................................................................ 28
Output Harness Wiring................................................................................. 28
J11 Annunciator Outputs
22.1
22.2
22.3
Description.................................................................................................. 29
Model 300 Harness Wiring............................................................................ 29
Model 860 Relay Module .............................................................................. 29
J23 6-Pin Header
23.1
Description.................................................................................................. 29
J22 LX-Bus Expansion Connector
24.1 Description.................................................................................................. 30
24.2 LX-Bus Interface Cards................................................................................. 30
24.3 LX-Bus LEDs................................................................................................ 30
24.4. OVC LED ....................................................................................................... 30
J21 Serial Connector
25.1
25.2
Description.................................................................................................. 30
Serial Connector LEDs.................................................................................. 30
J1 Ethernet Connector
26.1 Description ..................................................................................................... 31
26.2 Ethernet LEDs ............................................................................................. 31
Reset and Tamper Headers
27.1
27.2
J16 Reset Header ....................................................................................... 31
J4 Tamper Header ...................................................................................... 31
Universal UL Burglary Specifications
28.1
28.2
28.3
28.4
28.5
28.6
Introduction ................................................................................................ 32
Wiring ........................................................................................................ 32
Control Outside of Protected Area ................................................................. 32
Police Station Phone Numbers ...................................................................... 32
System Maintenance .................................................................................... 32
UL Listed Receivers...................................................................................... 32
Area Information
29.1
29.2
29.3
29.4
29.5
Ownership .................................................................................................. 32
Annunciation ............................................................................................... 32
Trouble Display............................................................................................ 32
Closing Wait ................................................................................................ 32
Local Bell Supervision .................................................................................. 32
UL 1023 Specifications
30.1
30.2
30.3
30.4
30.5
30.6
XR2500F Installation Guide
Audible Devices ........................................................................................... 33
Auxiliary Circuits .......................................................................................... 33
Bell Cutoff................................................................................................... 33
Entry Delay ................................................................................................. 33
Exit Delay ................................................................................................... 33
Weekly Test................................................................................................. 33
Digital Monitoring Products
iii
TABLE OF CONTENTS
UL 1635 Specifications
31.1
31.2
31.3
31.4
31.5
31.6
System Trouble Display ................................................................................ 33
Digital Dialer Telephone Number................................................................... 33
Test Time.................................................................................................... 33
Closing Wait ................................................................................................ 33
Entry Delay ................................................................................................. 33
Exit Delay ................................................................................................... 33
UL 1610 AND 1076 Specifications
32.1
32.2
32.3
32.4
32.5
32.6
32.7
32.8
Opening/Closing Reports.............................................................................. 34
Closing Wait ................................................................................................ 34
Entry Delay ................................................................................................. 34
Exit Delay ................................................................................................... 34
Proprietary Dialer ........................................................................................ 34
Grade B Central Station................................................................................ 34
Bell Cutoff................................................................................................... 34
AA Network Communication ......................................................................... 34
UL 365 and 609 Specifications
33.1
33.2
33.3
33.4
33.5
33.6
33.7
33.8
System Trouble Display ................................................................................ 35
Entry Delay ................................................................................................. 35
Exit Delay ................................................................................................... 35
Grade A Bell ................................................................................................ 35
Bell Cutoff................................................................................................... 35
Automatic Bell Test ...................................................................................... 35
Line Security for Police Connect .................................................................... 35
High Line Security........................................................................................ 35
UL 294 Specifications
34.1
34.2
Panel Designation ........................................................................................ 35
Compatible Devices ..................................................................................... 35
Universal UL and NFPA Fire Alarm Specifications
35.1
35.2
35.3
35.4
35.5
35.6
35.7
35.8
35.9
35.10
35.11
35.12
35.13
Introduction ................................................................................................ 36
Wiring ........................................................................................................ 36
Transformer ................................................................................................ 36
End-of-Line Resistor..................................................................................... 36
System Trouble Display ................................................................................ 36
Fire Display ................................................................................................. 36
Police Station Phone Number........................................................................ 36
System Maintenance .................................................................................... 36
Audible Alarm.............................................................................................. 36
Fire Zone Programming................................................................................ 36
Style D Zones .............................................................................................. 36
Video Option ............................................................................................... 36
UL Listed Receivers...................................................................................... 36
UL 864 NFPA 72 (Chapter 9) Specifications
36.1
36.2
36.3
36.4
36.5
36.6
36.7
Zone Restoral Reports.................................................................................. 37
Power Fail Delay .......................................................................................... 37
Sprinkler Supervisory ................................................................................... 37
DACT Systems............................................................................................. 37
Local Protective Signaling Systems................................................................ 37
Remote Station Protective Signaling Systems ................................................. 37
Fire Protective Signaling Systems ................................................................. 37
UL 985 NFPA 72 (Chapter 2) Specifications
37.1
37.2
37.3
37.4
Bell Output Definition................................................................................... 38
Audible Devices ........................................................................................... 38
Auxiliary Circuits .......................................................................................... 38
Bell Cutoff................................................................................................... 38
Digital Monitoring Products
iv
XR2500F Installation Guide
TABLE OF CONTENTS
California State Fire Marshal Specifications
38.1
Bell Output Definition................................................................................... 38
New York City (MEA) Specifications
39.1
39.2
39.3
39.4
39.5
Introduction ................................................................................................ 38
Digital Dialer and Network Communication .................................................... 38
Wiring ........................................................................................................ 38
Communication Programming....................................................................... 38
Additional Requirements .............................................................................. 38
Wiring Diagrams
40.1
40.2
40.3
40.4
40.5
40.6
40.7
40.8
40.9
Multiple Notification Circuit Modules .............................................................. 39
Multiple Notification Circuit Modules for Zoned Annunciation ........................... 40
Dual Style D Zone Module Installation ........................................................... 41
Remote Station Reversing Relay Connection .................................................. 42
Second LX-Bus™ with Auxiliary Power Supply ................................................ 43
Multiple Notification Circuits with Strobes and Bells ........................................ 44
Rothenbuhler 5110 High Security Bell Wiring ................................................. 45
LX-Bus™ Module Connection ........................................................................ 46
Model 860 Relay Module Connection ............................................................. 47
Operating Instructions Model XR2500F Panels
Mounting Instructions ............................................................................................. 48
Listings and Approvals
XR2500F Installation Guide
Digital Monitoring Products
v
REVISIONS
Revisions to This Document
This section explains the changes made to this document during this revision. It lists the date and identifies
the change(s) made, the related section number and section heading, and a summary of the change.
Date Section Number and Heading
10/05 2.6 Wiring Diagram
6.5 LX-Bus Expansion
12.6 Outputs
13.2 Output Expansion
14.1 Wiring Diagram
14.3 Accessory Devices
14.4 Mounting Keypads
14.5 Connecting Bus Devices
15.7 Standby Battery Calculations
15.8 Standby Battery Selection
16.1 Terminals 5 and 6
21.1 Dry Contact Relay Outputs
21.3 Output Harness Wiring
23.1 J23 6-Pin Header Description
24.1 J22 LX-Bus Description
39.1 through 39.5
Back Page
Digital Monitoring Products
vi
Quick Explanation of Changes
Updated End-of-Line (EOL) resistor information.
Added LX-Bus wiring information.
Clarified output operation.
Clarified 716 and 717 zone expander operation.
Updated EOL resistor information. Added 693 and Thinline keypad
models.
Added 693 and Thinline keypad models.
Added 693 and Thinline keypad models.
Clarified J22 on-board LX-Bus information.
Added 693 and Thinline keypad models.
Added notes regarding transformers and battery recharge time.
Clarified bell output operation.
Removed unsupported functions from listing.
Removed 431 reference. Revised J2 Output Color Code wire colors.
Added J16 reset information.
Added LX-Bus wiring information.
Added New York City MEA Specifications.
Note: Subsequent section numbers changed.
Added Listings and Approvals.
XR2500F Installation Guide
INTRODUCTION
Introduction
1.1
Overview
The DMP XR2500F Addressable Fire Alarm Control Panel (FACP) is an expandable 24 VDC Fire Alarm Control
with built-in DACT and LCD Fire Command Center keyboard with membrane keyswitch. A complete system
can provide a total of 574 programmable inputs and outputs for commercial and industrial fire alarm service.
The 24 VDC 4 Amp notification appliance power is distributed between two class B style W NAC outputs.
Additional NAC outputs can be added with conventional supervision modules or addressable power supply/
boosters. Addressable smoke detectors and input modules round out the XR2500F to deliver a truly flexible
and expansive fire detection and notification system. The Fire Alarm Control Panel is shipped pre-wired
in a red metal enclosure housing the necessary components to monitor and control fire alarm notification
appliances. The enclosure dimensions are as follows: 32” H x 14.5” W x 4” D. The lid adds about 0.5” to
each side.
1.2
System Components
The XR2500F FACP consists of the following components:
•
•
•
•
•
1.3
One Model XR2500F Command Processor panel
Two Model 866 Class B Style W NAC modules
One Model 504-24 VDC Power Supply
One 16 VAC, 56 VA transformer
One Model 481 Zone Expansion Interface Card
•
•
•
•
•
One Model 893A Dual Phone Line module
One Model 630F PCB and membrane switch
One 28 VAC transformer
Two Model 305 Plug-in Relays
One Metal Backplate
Power Specifications
Command Processor:
Transformer Input: 16 VAC 56 VA
Standby battery: 12 VDC, 1.0 Amps Max. charging current
Auxiliary power:
12 VDC output at 1.5 Amp Max
All circuits are inherent Power Limited except red battery wires.
NAC Output:
24 VDC 4 Amps shared between NAC 1 and 2
Note: For UL installations, the total current combined from Auxiliary Power cannot exceed:
1.3 Amps with a 50 VA transformer, 1.0 Amp Max for Auxiliary Power
1.9 Amps with a 56 VA transformer, 1.0 Amp Max for Auxiliary Power.
1.4
Before You Begin
Before installing the XR2500F, we recommend you read through the entire contents of this guide.
Familiarize yourself with the panel features and the key points to remember during the installation. Be sure
to read and understand all of the caution statements printed in bold italics.
1.5
About this Guide
The information in this guide is organized into five sections: Table of Contents, Introduction, Installation,
Compliance, and System Wiring Diagrams.
• The Table of Contents at the front lists the headings and subheadings used throughout each guide section.
• The Introduction section provides an overview of the XR2500F and this document.
• The Installation section begins with enclosure mounting instructions. Wiring diagrams for each component
also appear in this section.
• The Compliance section lists all UL listings the XR2500F currently follows.
• The System Wiring Diagrams provide illustrations of typical XR2500F systems.
1.6
How to use this Guide
To locate information about the XR2500F installation, refer to the Table of Contents at the front of this
guide. Find the subject heading that best describes the information you need and turn to the section
number shown to the left of the heading. If you cannot find the information you need under that heading,
scan through a few of the headings and read the text under those that sound similar.
XR2500F Installation Guide
Digital Monitoring Products
1
INTRODUCTION
Mounting
2.1
Mounting the Enclosure
The XR2500F must be mounted in a secure,
dry location to protect the unit from damage
due to tampering and the elements. The
enclosure can be either flush mounted or
surface mounted and includes a hinged door
with lock. The hole in the enclosure door
allows access to the Fire Command Center
without opening the door. Figure 1 illustrates
the mounting hole locations for the panel
enclosure.
���������������������
���������������
���������
��������������������������
The enclosure dimensions are 32” tall, 14.5”
wide, by 4” deep. The lid adds about 0.5” to
each side.
2.2
Surface Mounting
The enclosure center hole should be attached
to a wall stud. Due to the enclosure weight,
especially the batteries, it is extremely
important to mount the enclosure on the
stud. Attach the two holes beside the center
hole to sheetrock to secure enclosure. When
mounting the enclosure, be sure to leave
room for the panel door to swing open. The
door lock should be easily accessible.
2.3
������������������������
��������������
Flush Mounting
The enclosure can also be flush mounted. Use
1” screws to secure the enclosure between
two studs using the two sets of holes on
the sides of the enclosure. Use the top and
bottom holes to secure to horizontal studs, if
necessary.
2.4
Fire Command Center LCD
Keyboard
A Fire Command Center LCD Keyboard
has been factory installed on the XR2500F
enclosure. A keyswitch has also been
installed and pre-wired to the left of the
keyboard. The user can turn the keyswitch to
enable the four function keys without opening
the enclosure door.
2.5
Metal Backplate
�������������
�������������������������������������
�����������������������
Figure 1: Mounting the XR2500F Enclosure
The XR2500F components are pre-wired and installed on a metal backplate. The backplate can be easily
removed to keep components safe during pre-wire activities.
Remove AC and battery power from the XR2500F panel before removing the backplate. Disconnect
all battery, transformer, and the Fire Command Center LCD keyboard wires. Also remove the AC wires from
the 504-24 power supply. From the panel, disconnect the AC wires from terminals 1 and 2. Disconnect the
battery wires either from the batteries or the panel terminals 3 and 4. Finally, disconnect the keyboard
wires from panel terminals 7, 8, 9, and 10.
Remove the screws securing the backplate to the enclosure. Loosen the two top screws that the backplate
hangs on. After loosening and removing the screws, lift the backplate up slightly and pull the backplate
toward you. When reinstalling the backplate, be sure all connections are secure.
Figure 2 illustrates the backplate and the components. The backplate is shown in light gray.
Digital Monitoring Products
2
XR2500F Installation Guide
INTRODUCTION
2.6
Wiring Diagram
The XR2500F system below shows the component layout. The wires shown in this guide have been factory
installed and connected. The dashed lines represent wires running underneath or behind a component.
Detailed wiring diagrams for each supplied component appear in following sections of this guide.
�������
����������������������������������������������������������������������
��������������������������������������������������������������������������
������������������������������������������������������������������������
�����������������������������������������������������������������������
������������������������������������������������������������������
����������������������������������������������������������������������������
��������������������������������������������������������������������������������
�����������������������������������������������������������������������
������������� ������������� ������
������
�����
�����
���������
������
������
��������
�����
��������
�����
��������������������������
���������������������������
��������������������������
���������������������������
�����
����
�
�
�
�����������������
�������
�����������
����
�������
��
�����
�����
�����
�����
�����
�������
�����������
������������������
����������������
���������������
��������
������������������
�������������
�
����
�������
��
���������������������
������������������������
��������������������������
������������������
�������������������
� �������
�
�
�
�
�
������
�������
������������
����
����������������
����������
�������
��������������������������
����������������������������
��������������������
���
������������������
�������
���
���������������������
�������������������
��
������
����
������������������������������
�����������������
���������������
�������
�������������������������
�����������������������������
���������������������������
���������������������������
������������������������
������������������������
���������������������������
��������������������
������������������������������
�������������������������
����������������������
�������������������������
������������������������
�����������������������������
������
���
��
��
��
����
�� �� ��
�
�������� ��� ��������
���
�������
�����
�
���
�������������������������
������������������������������
��������������������������
�����������������
���
���
�
�
�
�������������
�����������������
�
�
�
�
�
�
�
�
��
��
�� ��
��
��
��
�� ���� ��� ��� ��� ��� ��� ��� ��� �� ��� ��
�����
�������������������������������
��������������������������
��
��������
������
���
������������������������������������
���������������������������
������������������������������
���������������
�������
�������
����������
�����
��
������
��������
������������
����������������������������
����������������������������
�����������������������
����������������������
��������������������������
������������������
�����������������������
�������������������
���� ����
�����
����������������
�����������������������������
������������������
���
�����
��
��
��
�
�����������
�� ��� ��
�� ��
��
�� ��� ��
�� ��
��
�� ��� �� ��� ��� ���� ����
�� ��
��
�� ��
��
��
���������������
��
����������������������������������������
�
�
�
�������������������������������
�������������������������������
���������������������������������������
��
�����������������������������
���������������������
�����������������������������
�����������������������
������������������������
�����������������������
��������������
��������������
�������
�������
�
������������������������������
����������������������������������
���������������������������������������
��������������������������������������
�������������������
�����������������������������
��������������
�������������
���������
��
��������������������������
��������������������������
������������������������������
����������������������������
�������������������
�
�
���������������������
�����������������������������
���������������������������
����������������������
�����������������������
��������������
Figure 2: XR2500F System
XR2500F Installation Guide
Digital Monitoring Products
3
INTRODUCTION
AC Connection
3.1
Transformers and AC Power Connection
The AC connection should be completed by a licensed electrician.
Never share the Fire Alarm Control Panel circuit with any other equipment.
The XR2500F comes supplied with two transformers: the 16 VAC 56 VA transformer and the 28 VAC 175
VA transformer. The 28 VAC and the 16 VAC transformer white leads and black leads must be connected
together respectively. These wires must be connected to an unswitched 120 VAC 60 Hz power source with at
least 1.85 Amps of available current.
Black wire - attach the black 120 VAC wire to the transformer black wires.
White wire - attach the white 120 VAC wire to the transformer white wires.
Green wire - attach the green wire lead to the green wire attached to the enclosure.
��������
���
�
�����
����
�
�����
�
����������������
������������
����
����������
�����
��������
�������
�����������
��������
���
������
�����
�����
�����
�����
�������
�����������
������������������
��������������������
������
�����
���������� ����������
����������������
Figure 3: Transformers and AC Power Connection
Always ground the panel before applying power to any devices! Use 18 AWG or larger for all power
connections. The XR2500F must be properly grounded before connecting any devices or applying power
to the panel. Proper grounding protects against Electrostatic Discharge (ESD) that can damage system
components.
3.2
28 VAC Transformer
The 28 VAC Transformer supplies power to the AC terminals of the 504-24 Power Supply which is factory prewired to the two 866 NAC modules. The 28 VAC is located in the upper right hand corner of the enclosure
surrounded by a metal divider. See Figure 3 above and the 504-24 Power Supply section.
3.3
16 VAC Transformer
The 16 VAC 56 VA transformer supplies power to the XR2500F panel and is factory pre-wired. See Figure 3:
Transformers and AC Power Connection. Also refer to Figure 11: XR2500F Panel Wiring Diagram.
3.4
Earth Ground from the XR2500F Panel
The XR2500F terminal 4 must be connected to earth ground using 14 AWG or larger wire to provide proper
transient suppression. DMP recommends connecting to a cold water pipe, building ground, or ground rod
only. Do not connect to an electrical ground or conduit, sprinkler or gas pipes, or to a telephone company
ground.
Digital Monitoring Products
4
XR2500F Installation Guide
INTRODUCTION
Secondary Power Supply
4.1
Description
The XR2500F system includes pre-wired cables for connecting a 24 VDC battery to the 504-24 power supply
and a 12 VDC battery to the XR2500F panel. For 24 VDC battery operation to the 504-24, connect two 12
VDC sealed lead-acid batteries in series using the included series connecting strap. See Figure 4. Observe
polarity when connecting all batteries.
Use sealed lead-acid batteries only. Use the DMP Model 367, 368, 369, 365, 366, 12 VDC sealed lead-acid
rechargeable batteries. Batteries supplied by DMP or manufactured by Eagle Picher or Yuasa have been
tested to ensure proper charging with DMP products.
Gel cell batteries cannot be used with the XR2500F panel.
4.2
Battery Connection to XR2500F Command Processor panel
For 12 VDC battery operation to the XR2500F, connect the black battery lead to the battery negative
terminal. The black battery wire connects to XR2500F panel terminal 4.
Connect the red battery lead to the battery positive terminal. The red battery wire connects to XR2500F
panel terminal 3. See Figure 11 and Figure 2.
Add a second battery in parallel using the DMP Model 318 Dual Battery Harness. When wiring two batteries
with the Model 318 Dual Battery Harness, plug the Dual Battery Harness red male end into the panel red
female battery lead. Plug the Dual Battery Harness black male end into the panel black female battery
lead. Attach both Dual Wiring Harness female leads to the two batteries as described above. See Table 3:
Battery Calculations.
4.3
Battery Connection to the 504-24 Power Supply
The 504-24 is powered by 24 VDC. Two 12 VDC batteries connect together using the series connecting strap.
The black battery wire connects to the 24 VDC battery negative terminal and to the 504-24 negative AC
terminal.
The red battery wire connects to the 24 VDC battery positive terminal and to the 504-24 positive AC
terminal. See Figure 4, Figure 9, and Figure 2. Also see the Battery Information section.
���
�������
�����������
�����
�����
�������
�������
�������
�������
Figure 4: 24 VDC Battery Wiring
XR2500F Installation Guide
Digital Monitoring Products
5
INTRODUCTION
Two 866 NAC Modules
5.1
Description
Each 866 provides one style W indicating circuit for supervising UL polarized notification appliances, such as
bells, strobes, and horns. See Table 1: Notification Appliances for a list of approved notification appliances.
5.2
Connection
Each 866 module is pre-installed on the removable backplate using the standard three-hole configuration.
The modules are factory pre-wired to each other, the 504-24, and the XR2500F panel. Refer to the figure
below and to Figure 2: XR2500F System for wiring connections.
You can connect 24 VDC Notification Appliances to terminals 5 and 6 of each module. Each module provides
a zone of notification and can be activated separately.
���������������������
�������
�������������
����
���������
���������
�����
����������
�������������
������������
������������
��������������
��������������
��������������������������������
������
�������������������������������
�����������
����������
�������������
����������
�������������
�������������
����������
��������������������
���������������������
�������
�������������
����
���������
���������
�����
����������
�������������
������������
������������
��������������
��������������
���������������������
���������������
��������������������������������
��������������
��������������������
�������������������������������
������������������������������
������
�����������
����������
�������������
����������
�������������
�������������
����������
Figure 5: 866 Modules Wiring
5.3
Bell Silence/Bell Trouble
A bell silence switch on the 866 module is provided to prevent indicating devices from sounding during
system testing. When the Silence position is selected, a 15-second delay occurs before the 866 bell trouble
contacts (terminals 7 and 8) open. Select the Normal position after testing to return the 866 module to
normal operation.
Digital Monitoring Products
6
XR2500F Installation Guide
INTRODUCTION
5.4
Notification Appliances
The following table indicates the approved notification appliances that can be used with the XR2500F
system.
DMP Part Number
Description
Wheelock Model No.
12V
24V
802
Multi-tone Horn
MT-12/24
X
X
803
Standard Horn
NH-12/24
X
X
831
Sync Module, Single circuit
SM-12/24-R
X
X
832
Sync Module, Dual circuit
DM-12/24-R
X
X
901
Mini Horn
MIZ-24
X
904
Horn
AH-24
X
904WP
Weatherproof Horn
AH-24WP
X
906-6
6-Inch Bell
MB-G6-24-R
X
906-10
10-Inch Bell
MB-G10-24-R
X
921WP-75W
Weatherproof Strobe
RSS-2475C-FW
X
921-MCW
Multi-Candela Strobe
RSS-24MCW-F
X
922-MCW
Multi-Candela Strobe with Retrofit
Plate
RSSP-24-MCW-F
X
923-MCW
Multi-Candela Horn Strobe
NS-24MCW-F
X
924-MCW
Multi-Candela Audible Strobe
AS-24MCW-F
X
924WP-75W
Weatherproof Audible Strobe
ASWP-2475W
X
Table 1: Notification Appliances
XR2500F Installation Guide
Digital Monitoring Products
7
INTRODUCTION
LX-Bus™ Operation
6.1
Description
The XR2500F Command Processor™ panel supports LX-Bus operation directly from the panel. Each LX-Bus
circuit provides 100 additional zones. Use J22 LX-Bus Header for the first 100 zones. Use the installed 481
Zone Expansion Interface Card for the next 100 zones. This provides a total of 200 expansion zones. To
install up to four additional Interface Cards use a Model 461 Interface Adaptor Card.
6.2
XR2500F On-board LX-Bus
To enable J22 to operate as an LX-Bus, place a jumper on the two pins next to the letter “L” on the J23
6-Pin header. When using J22 as an LX-Bus, connect a DMP Model 300 4-wire Harness to the J22 4-pin header
labeled LX-BUS. This provides the first 100 LX-Bus zones numbered 500-599. Respect wire colors when
connecting devices and use all four wires. Reset the panel using J16 jumper to activate LX-Bus operation.
Note: Do NOT use shielded wire when using the LX-Bus. Do NOT connect the wires from the 4-wire harness
to the panel terminals.
6.3
LX-Bus 481 Zone Expansion Interface Card
The 481 Zone Expansion Interface Card provides an additional 100 zones to the XR2500F. When used in
conjunction with the on-board J22 LX-Bus the 481 LX-Bus zones are numbered 600 to 699.
6.4
Installing the 481 Card
Remove AC and battery power from the XR2500F panel and ground yourself before handling and
installing the 481 Card.
1. Align the 481 Card 50 pin connector with the XR2500F panel J6 connector.
2. Press the 481 onto the J6 connector while applying even pressure to both sides.
������������������
�����
���������
����������
����������
����
������������������
���������
���������������
������������������
�
�����������������
�� ��� ��
��
��
��
��
�� ��� ��
��
��
��
��� ��� ���� ����
��
��
��
��
�������������������
��������������
��������������
������������
Figure 6: 481 Wiring
6.5
LX-Bus™ Expansion Capability
The on-board LX-Bus and the 481 Card each provide one 4-wire LX-Bus™ connection that allows you to
connect up to 100 Model 521LX, 521LXT, or SLRLX Addressable Smoke Detectors. Also each LX-Bus™ could
connect up to 25 Model 714, 715, and 725 Zone Expanders or 716 Output Expanders, up to six Model 714-16
or 715-16 Zone Expanders, and up to 100 Model 711 Zone Expanders. Power for the devices connected to
the 481 Card is provided through the expansion harness Black and Red wires.
Digital Monitoring Products
8
XR2500F Installation Guide
INTRODUCTION
893A Dual Phone Line Module
7.1
Description
The 893A is a dual telephone line supervision module that allows the panel to indicate a phone line failure
to the premises and the central monitoring station. After the 893A senses a failure on the main line, it
switches to the backup, or secondary, phone line. The 893A installs on the removable backplate above the
XR2500F circuit board.
7.2
Connection
The prewired 893A connects the panel to the public telephone network through an installed DMP 356 RJ
Cable between the XR2500F panel J3 connector and the 893A Module J3 connector labeled PANEL.
������������������
�����������������
�����������
�������������
��
�����
�������������������������������
�����������������������
���������������������
��
���
���
������������������
�����������������
�������������
��
��
�����������
��������������
��
����
��
���
��
������
����������
��������������
���������������������������
Figure 8: 893A Dual Phone Line Module Wiring
7.3
Jumper Settings
The 893A module has two sets of jumpers. Both communication jumpers must be set for DD (digital dialer)
operation. Do not set the 893A jumpers next to MPX. The 893A Module supports multiplex operation, but
the XR2500F panel does not.
7.4
Digital Dialer
You can configure the 893A to provide two lines of digital dialer. The XR2500F is preset at the factory for
Digital Dialer. The Main modular jack (J4) is used for the primary digital dialer line. The Backup modular
jack (J5) is used for the secondary digital dialer line.
7.5
Phone Line Monitor
The 893A uses a phone line monitor for the main and backup phone lines. When sending a report, the 893A
verifies the main phone line is working before sending data. If the line is bad, the module tests the backup
phone line. The 893A sends the report on the first working phone line.
The phone line monitor has a two-minute trouble delay and a one-minute restore delay. Phone line trouble
is displayed in the Fire Command Center LCD Status List as a System Trouble. The Fire Command Center
LCD is factory programmed to display system troubles in the Status List.
7.6
Processor Fail Buzzer
The 893A module also monitors the panel CPU and sounds a trouble buzzer whenever either the panel
processor is reset using J16 or the processor stops functioning.
7.7
J10 893A Connector
The 893A Dual Phone Line Module connects to the XR2500F J10. Refer to the 893A Installation Sheet
(LT-0135) for complete information.
7.8
Ground start
Ground start phone service cannot be used on commercial or residential fire applications.
XR2500F Installation Guide
Digital Monitoring Products
9
INTRODUCTION
7.9
Notification
The user must not repair registered terminal equipment. In case of trouble, immediately unplug the device
from the telephone jack. The factory warranty provides for repairs. Registered terminal equipment may
not be used on party lines or in connection with coin telephones. Notify the telephone company with the
following information:
a. The particular line(s) where the service is connected
b. The FCC registration number as listed in Section 7.5
c. The ringer equivalence
d. The device make, model, and serial number (see the serial # sticker on the panel)
7.10 FCC Registration
The Model XR2500F complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On
the outside of the enclosure of this equipment is a label that contains, among other information, a product
identifier in the format US:CCKAL00BXR500. If requested this number must be provided to the telephone
company.
A plug and jack used to connect this equipment to the premises wiring and telephone network must comply
with the applicable FCC Part 68 rules and requirements adopted by the ACTA. See installation instructions
for details.
The Ringer Equivalence Number (REN) is used to determine the number of devices that may be connected
to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to
an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of
the number of devices that may be connected to a line, as determined by the total RENs, contact the local
telephone company.
If the XR2500F causes harm to the telephone network, the telephone company will notify you in advance
that temporary discontinuance of service may be required. But if advance notice isn’t practical, the
telephone company will notify the customer as soon as possible. Also, you will be advised of your right to
file a complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operations or procedures that could
affect the operation of the equipment. If this happens the telephone company will provide advance notice
in order for you to make necessary modifications to maintain uninterrupted service.
If trouble is experienced with the Model XR2500F, for repair or warranty information, please contact DMP at
the address and telephone number listed on the back of this document. If the equipment is causing harm to
the telephone network, the telephone company may request that you disconnect the equipment until the
problem is resolved.
If your premises has specially wired alarm equipment connected to the telephone line, ensure the
installation of the XR2500F does not disable your alarm equipment. If you have questions about what will
disable alarm equipment, consult your telephone company or a qualified installer.
Caution: To ensure proper operation, this equipment must be installed according to the installation
instructions in this manual. To verify that the equipment is operating properly and can successfully report an
alarm, this equipment must be tested immediately after installation, and periodically thereafter, according
to the test instructions in this document and the XR500 Series Programming Guide (LT-0679). Additionally,
verification of Line Seize capability should be made immediately after installation, and periodically
thereafter, in order to ensure that this equipment can initiate a call even when other equipment (telephone,
answering system, computer modem, etc.) connected to the same line is in use.
Digital Monitoring Products
10
XR2500F Installation Guide
INTRODUCTION
504-24 Power Supply
8.1
Description
The 504-24 is a power limited, switching power supply that meets UL, CSFM, NFPA, and FCC compliance
standards. Model 504-24 is rated for 24 VDC @ 4 Amps maximum and supplies power to the 866 Modules.
8.2
LEDs
The 504-24 has two status LEDs that show the current state of power. The green LED indicates low AC input.
The red LED indicates low standby battery power after AC has failed.
8.3
504-24 Condition Chart
LED
Status
AC Trouble
Condition
Approximately. 102 VAC
Voltage Levels
AC LED (Green)
On
AC Good
Condition
Battery Trouble
Below 23.6 VDC
AC LED (Green)
Off
AC Bad
Battery Restoral
Above 25.0 VDC
DC LED (Red)
On
Battery Good
Battery Cutoff
Below 20.4 VDC
DC LED (Red)
Off
Battery Bad
Table 2: 504-24 Condition and LED Indicators
8.4
504-24 UL Listings
For UL 603 Power Supplies for Burglary Alarm Systems and UL 294 Power Supplies for Access Control System
applications: Voltage Range of 22.9 to 25.5 VDC.
For UL 1481 Power Supplies for Fire Protective Signaling the following maximum battery standby Ampere
hours apply for 24 hours of battery backup:
Battery Standby Maximum: 49.2Ah
Output Voltage: 24 VDC
Output Current: 1.5A standby, 4 Amp alarm
8.5
24 VDC NAC Standby Battery Calculations
The following calculation defines the total number of standby battery Amp-hours required to support
operation of the NACs and any other devices attached to the 504-24 power supply. From this calculation,
assemble the appropriate number of batteries that will just exceed the calculated total Amp-hour
requirement. The 866 NACs receive power for internal operation from the XR2500F panel and do not enter
in this calculation themselves.
1. Add all standby current values including the power supply operating current.
2. Multiply the total standby current by the number of standby hours needed.
3. Add all alarm current values from the notification appliances attached to the 866 NACs and multiply by
0.25.
4. Add the total alarm mA-hour with the total standby mA-hour and then multiply this number by 0.001.
Power Supply Operating Current
200 mA
Other Standby Current
+
______ mA
Total Standby Current
+
______ mA
Number of Standby Hours Required
X
______ hr
2.
Total Standby (mA-hr) Required
=
______ mA-hr
3.
Total Alarm Current
=
______ mA
Total Alarm Current X 0.25
=
______ mA-hr
Total Standby (Required)
+
______ mA-hr
Total
=
______ mA-hr
X
0.001
=
______
1.
(0.25 = 5 minutes in alarm)
4.
Total Required Amp-hours
Table 3: Battery Calculations
XR2500F Installation Guide
Digital Monitoring Products
11
INTRODUCTION
8.6
Connection
The 24 VDC power supply is completely pre-wired. Refer to the following 504-24 wiring diagram for specific
wire connections.
������
�������������������
������
��������������
�������
�����������
�����
�����������������
�����������������
�����
�����������������
����������������
���������
�����������������
������������������������
����
���
������
���
����
����
���
�����������������
��������������������
�������
�����
��
��������������������� ���
�������������������
����������������������� �����
�������������������
�����
����� �����������������
����������������������
����������������� �����������������
�������������������� ��������������������
Figure 9: 504-24 Wiring
Interconnect Wiring Harness
9.1
Interconnect Harness
This chart explains the wire colors on the Interconnect Wiring Harnesses. It also explains to what each wire
connects.
Wire Color
Connection From
Connection To
Red
Panel Terminal 7 (DC Power)
866 Module #2 Terminal 1 (Auxiliary Power)
Black
Panel Terminal 10 (Common)
504-24 DC - Negative DC Terminal (Ground)
Brown
Panel Terminal 13 (Zone 1)
866 Module #1 Terminal 7 (Bell Trouble)
Violet
Panel Terminal 15 (Zone 2)
866 Module #2 Terminal 7 (Bell Trouble)
Green
Panel Terminal 16 (Zone 3)
504-24 Battery Trouble Terminal N/O
White
Panel Terminal 18 (Zone 4)
504-24 AC Trouble Terminal N/C
Gray
Panel J2 Pin 2 (Common)
866 Module #1 Terminal 3 (Alarm In)
Orange
Panel J2 Pin 3 (Output 1 N/O)
Panel Terminal #5 (Bell Output)
White
Panel J2 Pin 5 (Common)
866 Module #2 Terminal 3 (Alarm In)
Yellow
Panel J2 Pin 6 (Output 2 N/O)
Panel Terminal #5 (Bell Output)
White/Red
504-24 DC + (Positive DC Terminal)
866 Module #2 Terminal 4 (Bell Power In)
Black
504-24 DC - (Negative DC Terminal)
866 Module #2 Terminal 2 (Ground)
Red
866 Module #2 Terminal 1 (Auxiliary Power)
866 Module #1 Terminal 1 (Auxiliary Power)
Black
866 Module #2 Terminal 2 (Ground)
866 Module #1 Terminal 2 (Ground)
Black
866 Module #2 Terminal 2 (Ground)
866 Module #1 Terminal 8 (Bell Trouble)
White/Red
866 Module #2 Terminal 4 (Bell Power In)
866 Module #1 Terminal 4 (Bell Power In)
Black
866 Module #2 Terminal 8 (Bell Trouble)
504-24 Battery Trouble Common Terminal
Black
866 Module #2 Terminal 8 (Bell Trouble)
866 Module #1 Terminal 8 (Bell Trouble)
Table 4: Interconnect Wiring Harness
Digital Monitoring Products
12
XR2500F Installation Guide
INTRODUCTION
Fire Command Center
10.1 Description
The XR2500F provides an LCD display and 20-key keyboard for programming and system user operation. The
Fire Command Center is installed on the XR2500F enclosure door. A keyswitch is installed and pre-wired
to the left of the keyboard. The user must turn the keyswitch to enable the four function keys. See the
illustration below.
Figure 10: Fire Command Center LCD and Keyboard
10.2 Connection
The display and keyboard are factory pre-wired to the XR2500F panel terminals 7, 8, 9, and 10. For standby
battery calculations, the display draws 92mA of current in normal standby or alarm condition. See Panel
Standby Battery Calculations. The keyswitch is pre-wired to the membrane keyboard.
10.3 Remote Fire Command Center
Up to fifteen Model 630F Remote Fire Command Centers may be remotely attached to the XR2500F system.
See the 630F Installation Guide (LT-0741) for complete information.
XR2500F Installation Guide
Digital Monitoring Products
13
INSTALLATION
Panel Features
11.1 Description
The DMP XR2500F Command Processor™ Panel is a versatile 12 VDC, fire communicator panel with battery
backup. The XR2500F provides eight on-board grounded zones for connecting Model 860, Class A zones and
two on-board 12 VDC Class B, Stye A powered zones. The powered zones have a reset capability to provide
for 2-wire smoke detectors, relays, or other latching devices. The XR2500F can communicate to one or two
DMP SCS-1/SCS-1R Receivers using digital dialer or network communication, or to non-DMP receivers using
the Contact ID format.
11.2 Connection
The XR2500F Command Processor panel is factory pre-wired and controls the other components in the
system. Refer to the wiring diagram below for wiring. See the following sections for descriptions of
additional XR2500F applications.
To 893 J3 PANEL Connector
J4
Tamper
To 866 Module
#2 terminal 3
(Alarm In)
Link LED
Activity LED
J1
Ethernet
RS-232
J22
LX-Bus
To 893 P10
Connector
J10
Battery
Start
J2
K6
J8
PROG
AC AC +B –B BELL GND RED YEL GRN BLK SMK GND Z1 GND Z2
1
2
3
4
5
6
7
8
9
10
11
12 13
To 16 VAC
Transformer
To Fire
Command
Center
Red wire to
positive terminal
of 12 VDC Battery
To 866 Module To 504-24
#2 terminal 1
DC (AUX PWR)
Black wire to
negative terminal
of 12 VDC Battery
14
K7
3
4
5
6
To LX-Bus
Modules
J6
Output 1 OVC Output 2
Out1 Out2
L
X
Annunciator Outputs (J11)
Output Color Code
Output 3
Red
Output 4
Yellow
Output 5
Green
Output 6
Black
To 866 Module
#1 terminal 3
(Alarm In)
J21
Power J23
R
LED
Form C Relays (J2)
Output Color Code
Output 2 N/O Yellow
Output 2 Com White
Output 2 N/C Blue
Output 1 N/O Orange
Output 1 Com Gray
Output 1 N/C Violet
481 Zone Expansion Interface Card
J3
Phone Line
XR2500F
Command Processor™
Panel
J11
J16
Reset
Outputs 3-6
Z3 GND Z4 Z5 GND Z6
15 16
17
18 19
20
Z7 GND Z8 Z9+ Z9– Z10+ Z10–
21 22
23
24 25
26
27
28
To 504-24
BATT TRBL
NC
To 866 Module
#2 terminal 7
(BELL TRBL)
To 866
Module #1
terminal 7
(BELL TRBL)
To 504-24
AC TRBL
NC
Figure 11: XR2500F Panel Wiring
11.3 Relays
The XR2500F ships with two Model 305 Relays pre-installed to allow zone alarm control for the 866 NAC
Modules. When a fire alarm occurs the bell output is factory programmed to turn on and provide power to
the contacts of the relays. Specific zone programming determines whether one or both relays turn on signal
voltage to the 866 NACs. This allows control of the NACs by zone.
11.4 Zone Reference
The XR2500F has been pre-wired in the factory. The first 866 NAC module connects to Zone 1. The second
866 NAC module connects to Zone 2. Zones 3 and 4 connect to the 504-24 power supply.
Digital Monitoring Products
14
XR2500F Installation Guide
INSTALLATION
XR2500F Product Specifications
12.1 Power Supply
Transformer Input: Primary input: 120 VAC, 60 Hz, Secondary output: 16 VAC 56 VA
Standby Battery:
12 VDC, 1.0 Amps Max. charging current
Auxiliary:
12 VDC output at 1.5 Amp Max
Bell Output:
12 VDC at 1.5 Amp Max
Note: The combined Auxiliary and Bell outputs total cannot exceed 3 Amps with a 56 VA Transformer.
All circuits are inherent Power Limited except the red battery wire and AC terminal.
Note: For UL installations, the total current combined from Auxiliary and Bell Power cannot exceed:
1.3 Amps with a 50 VA transformer, 1.0 Amp Max for Auxiliary Power
1.9 Amps with a 56 VA transformer, 1.0 Amp Max for Auxiliary Power and 1.5 Amp Max for Bell.
12.2 Communication
Built-in dialer communication to DMP Model SCS-1/SCS-1R Receivers
Built-in Contact ID communication to non-DMP receivers
893A Dual Phone Line Module with phone line supervision
Can operate as a local panel
12.3 Panel Zones
Eight 1k Ohm EOL burglary zones (zones 1 to 8). Connect to 869 Class A module for burglary applications.
Two 3.3k Ohm EOL powered zone with reset (zones 9 and 10).
Note: Use the supplied DMP Model 311 1k Ohm and DMP Model 301 3.3k Ohm resistors.
12.4 Keypad Bus
You can connect up to 16 of the following supervised keypads and expansion modules to the keypad bus:
• Alphanumeric Fire Command Centers or keypads
• Four- and/or single-zone expansion modules
• Single-zone detectors
• Access control modules
12.5 LX-Bus™
You can connect the following devices to the LX-Bus™ provided by the DMP 481 (supplied) or by the 462N,
481, 462P, 462FM, and 472 Interface Cards up to the maximum number of LX-Bus™ addresses. See Accessory
Devices.
• Model 521LX or 521LXT Smoke Detectors with CleanMe
• Model SLRLX Smoke Detectors
• Sixteen-, eight-, four- and/or single-zone expansion modules
• Single-zone detectors
• Relay output expansion modules
• Graphic annunciator modules
12.6 Outputs
The XR2500F provides two pre-installed Model 305 Single Pole, Double Throw (SPDT) relay outputs, each
rated 1 Amp at 30 VDC resistive (power limited sources only).
The XR2500F also provides four open collector outputs rated for 50mA each. The open collector outputs
provide ground connection for a positive voltage source. A Model 300 Output Harness is required to use
these outputs and may be connected to a Model 860 Relay Output Module.
XR2500F Installation Guide
Digital Monitoring Products
15
INSTALLATION
Expansion
13.1 Zone Expansion
Up to 574 fire and burglary zones are available on the XR2500F using DMP Security Command keypad remote
zone capability and zone expansion modules. The panel keypad data bus supports up to sixteen supervised
device addresses with each address supporting up to four programmable expansion zones.
Up to 500 zones are available using the on-board LX-Bus along with additional expansion modules. Use the
461 Interface Adaptor, 462N, 462P, 462FM, or 481 interface cards, and any combination of sixteen, eight,
four, and single point zone expander modules and single point LX-Bus detectors.
Combined current requirements of additional modules may require an additional 504-24 or 502-12 power
supply. See section Standby Battery Calculations when calculating power requirements.
Note: Do not use shielded wire for LX-Bus or Keypad Bus circuits.
13.2 Output Expansion
Note: Do not use shielded wire for LX-Bus or Keypad Bus circuits.
In addition to the two SPDT relays and four open collector outputs on the XR2500F, you can also connect up
to 25 Model 716 Output Expansion Modules to each LX-Bus. These modules can provide an additional 500
programmable SPDT relays.
The XR2500F provides 100 Output Schedules you can use for programming the 716 to perform a variety of
annunciation and control functions. You can also assign the 716 outputs to any panel Output Options such as
Fire Alarm, Communication Fail, or Phone Trouble Outputs. Refer to the 716 Installation Guide (LT-0183).
The LX-Bus™ also supports the Model 717 Graphic Annunciator Module. Each 717 module supplies 20
switched ground outputs that follow the state of their assigned zones.
Note: The 717 supports the first eight keypad bus zones. To follow Keypad Bus zones nine through 16, install
multiple 716 modules. Refer to the 717 Installation Guide (LT-0235) and 716 Installation Guide (LT-0183).
Digital Monitoring Products
16
XR2500F Installation Guide
INSTALLATION
Accessory Devices
14.1 Wiring Diagram
The XR2500F system below shows some of the accessory modules you can connect for use in various
applications. A brief description of each module follows in section 14.3.
s
s
J4
Tamper
Wiring on terminals 5 through 22 must
exit right and maintain 1/4" separation
from the AC and battery positive wiring.
Link LED
Activity LED
J1
Ethernet
Annunciator Outputs (J11)
Output Color Code
Output 3
Red
Output 4
Yellow
Output 5
Green
Output 6
Black
J21
RS-232
J22
LX-Bus
1⁄4"
J8
PROG
16 VAC
Transformer
Cold Water
Pipe Earth
Ground
Bell
Bell cutoff time
range is 5 to 99
minutes marchtime
and non-coded.
1k
Ohm
22 gauge minimum
s
s
s
11
12 13
15 16
S
S
S
1k
1k
Ohm Ohm
17
S
18 19
S
S
1k
1k
Ohm Ohm
20
S
S
21 22
S
23
S
S
1k
1k
Ohm Ohm
S
24 25
S
26
27
Zone
9
S
1k
1k
Ohm Ohm
S
28
Zone
10
S
S
S
Verification Control Unit
Delay
Zones
______
13.6 sec.
RED
BLACK
s
s
s
s
s
s
s
Zone Expander
Model 714
7mA @ 12 VDC
Models 714-8, 714-16
20mA @ 12 VDC
Zone
Expander
Model 711
7mA @ 12
VDC
Zone Expander
(up to 8 zones)
Model 712-8
19mA @ 12
VDC
Smoke
Detector
DISARM
ARM
1k Ohm 1k Ohm 1k Ohm
S
Smoke
Model
______
Detector
Delay
____sec.
Zone Expander
Model 715
7mA @ 12 VDC
Models 715-8, 715-16
20mA @ 12 VDC
RED
YELLOW
GREEN
Keyswitch Arming
s
can be connected
to any zone. See
LT-0681 Section 10.4.
Heat detectors, pull
stations, or any other
contact devices listed
for Fire Protective
Signaling can be
connected to zones
9 and 10.
Zones 9 and 10 and
Model 715 compatibility
identifier: A
Maximum operating
range: 9.8 VDC to
14.0 VDC.
Class B (Style A).
Zones 9, 10, and all
expanded zones are
suitable for Class B (as
applicable for the
initiating and signaling
line circuits per UL 864
Table 48.2 or 48.3).
Installation limits under
local Authority Having
Jurisdiction (AHJ).
Using verification delays
on zones 9 and 10 is
optional. Use the
delays marked on the
smoke detectors or
the smoke detector
installation wiring
diagram.
3.3k
3.3k
Ohm
Ohm
Resistor Resistor
Auxiliary Power
Total current combined from
terminals 7, 11, 25, and 27
1.5 Amp Max
10.2 VDC to 14.0 VDC
s s
J16
Reset
Z7 GND Z8 Z9+ Z9– Z10+ Z10–
s = Supervised Circuit
ARMED
s
S
S
POWER
s
14
Zone 3
10
J11
Z3 GND Z4 Z5 GND Z6
Zone 2
9
Zone 1
8
22 gauge minimum
RED
BLACK
6
BLACK
s
s
7
22 gauge minimum
5
GREEN
4
22 gauge minimum
3
16 to 18 gauge wire
Maximum AC Wire distance
with 16 gauge wire: 70 feet s
with 18 gauge wire: 40 feet
Bell
12 VDC nominal
Minimum cutoff time is
5 minutes.
1.5 Amp Max
Keypads
Models 690/690F
77mA at 12 VDC
Models 790/790F/791
77mA at 12 VDC
Model 693/793
92mA at 12 VDC
Model 630F
63mA at 12 VDC
Model 7060
80mA at 12 VDC
Model 7070
72mA at 12 VDC
Model 7063
86mA at 12 VDC
Model 7073
93mA at 12 VDC
2
RED
Secondary Power Supply
1.0 Amps Max. charging
current. Use only 12 VDC
rechargeable batteries.
DMP Models 365, 366, 367,
368, or 369. Replace
batteries every 3 to 5 years.
1
s
s
3
4
5
6
Outputs 3-6
AC AC +B –B BELL GND RED YEL GRN BLK SMK GND Z1 GND Z2
YELLOW
DMP Transformers
Model 322
16 VAC 56 VA
Class 2 Wire-in.
K7
Zone 5
J2
K6
Zone 6
J10
Battery
Start
Rear
Tamper
J6
UL Listed Resistors
1.0k Ohm - DMP Model 311
3.3k Ohm - DMP Model 309
10K Ohm - DMP Model 308
Output 1 OVC Output 2
Zone 4
L
X
Out1 Out2
Power J23
R
LED
Wire into a 120 VAC
60 Hz outlet not
controlled by a
switch with at least
1.85 Amps available
current.
Front
Tamper
481 Zone Expansion Interface Card
Form C Relays (J2)
Output Color Code
Output 2 N/O Yellow
Output 2 Com White
Output 2 N/C Blue
Output 1 N/O Orange
Output 1 Com Gray
Output 1 N/C Violet
AC Wiring must be in conduit and exit
out the left side of the enclosure.
Zone 8
J3
Phone Line
Zone 7
XR2500F
Command Processor™
Panel
S
S
S
S
S
S
1k Ohm 1k Ohm 1k Ohm
S
1k Ohm
S
S
S
S
S
S
S
S
S
3.3k Ohm 3.3k Ohm 3.3k Ohm 3.3k Ohm
S
1k Ohm
Use UL Listed Power
Supervision Relay
rated at 12 VDC.
1k Ohm
Figure 12: Typical XR2500F Wiring Diagram
14.2 Lightning Protection
Metal Oxide Varistors and Transient Voltage Suppressors help protect against voltage surges on XR2500F input
and output circuits. Additional surge protection is available by installing the DMP 370 or 370RJ Lightning
Suppressors.
XR2500F Installation Guide
Digital Monitoring Products
17
INSTALLATION
14.3 Accessory Devices
Interface Adaptor and Interface Cards
461 Interface Adaptor Card
Allows you to connect two or more expansion interface cards to the XR2500F panel. The 461 is an
expansion board that plugs into the panel J6 Interface Connector and is required when using two or more
Interface Cards. Use combinations of Interface Cards for expanding zones, network interfacing, and local
printing.
462N Network Interface Card
Allows you to connect the XR2500F to any compatible data network and use its communication capability
in place of standard dial out telephone lines. The 462N also provides an LX-Bus™ for connecting zone
and output expansion modules to the panel. The 462N is listed for Grade AA Burglary communication and
supplementary signaling.
462P Printer Interface Card
Allows you to connect the XR2500F to any compatible serial printer providing the user with real-time event
recording. The 462P also provides an LX-Bus™ for connecting zone and output expansion modules.
* 462FM 9600 Baud Modem
Allows you to remote-connect to the panel over telephone lines and upload/download at 9600 baud using
a standard Hayes compatible modem. The card shares the phone line with the panel and provides 100
LX-Bus zones and/or outputs.
481 Expansion Interface Card
Provides one LX-Bus for connecting up to 100 zone and output expansion modules.
Zone and Output Expansion Modules
710/710F Bus Splitter/Repeater
Allows you to increase keypad or LX-Bus™ wiring distance to 2500 feet. Model 710F is for 24 VDC
applications.
711 Single Point Zone Expanders
Provides one Class B zone for connecting devices.
712-8 Zone Expander
Provides Class B zones for connecting burglary devices.
714, 714-8, 714-16 Zone Expanders
Provides Class B zones for connecting non-powered fire devices.
715, 715-8, 715-16 Zone Expanders
Provides 12 VDC Class B powered zones for connecting smoke detectors, glassbreak detectors, and other
2- or 4-wire devices.
725 Zone Expanders
Provides 24 VDC Class B powered zones for connecting smoke detectors, glassbreak detectors, and other
2- or 4-wire devices. Requires 710F Bus Splitter/Repeater.
716 Output Expander
Provides four Form C relays (SPDT) and four switched grounds (open collector) for use in a variety of
remote annunciation and control applications.
717 Graphic Annunciator Module
Provides 20 zone following annunciator outputs (open collector) for use in a variety of remote annunciation
and control applications for use on the keypad bus only.
Indicating and Initiating Devices
865 Supervised Style Y or Z
Provides supervised alarm current when using the XR2500F panel bell output and up to 5 Amps at 12 or
Notification Circuit Module
24 VDC when using a listed auxiliary power supply. The 865 can supervise 2-wire Style Y or Z circuits for
ground faults, opens, shorts, and shorts with individual LED annunciation.
866 Notification Circuit Module
Provides supervised alarm current using the XR2500F panel bell output and up to 5 Amps at 12 or 24 VDC
when using a listed auxiliary power supply. The 866 can supervise Style W circuits for opens and shorts.
867 Style W LX-Bus Notification Circuit Provides supervised alarm current using the XR2500F panel bell output and up to 5 Amps at 12 or 24 VDC
Module
when using a listed auxiliary power supply. The 867 connects to the XR2500F panel LX-Bus™ and provides
one 2-wire Style W notification circuit for ground fault, open, and short conditions. Individual Bell Relay
addresses Bell Ring styles.
869 Dual Style D Initiating Module
Provides two Style D, 4-wire initiating zones for connecting waterflow switches and other non-powered fire
and burglary devices.
Accessory Modules and Keypads
893A Dual Phone Line Module
Allows you to supervise two standard phone lines connected to an XR2500F panel. The 893A module
monitors the main and backup phone lines for a sustained voltage drop and alerts users when the phone
line is bad.
* ePAD™ Virtual Keypads
Allows users to control the security system from any computer in the world using the Internet.
LCD keypads
Allows you to control the panel from various remote locations. Connect up to sixteen supervised Model
690/690F, 790/790F, 791 Security Command® keypads, 693/793 Easy Entry™ keypads, or 7060, 7063,
7070, or 7073 Thinline keypads to the keypad bus using terminals 7, 8, 9, and 10.
Addressable Smoke Detectors
521LX
Single-zone, addressable module conventional smoke/smoke heat detectors that connect to the LX-Bus.
SLRLX
Includes remote maintenance reporting, drift compensation, and multi-criteria detection.
* These devices have not been investigated by UL and shall not be used in UL installations.
Table 5: Accessory Devices
Digital Monitoring Products
18
XR2500F Installation Guide
INSTALLATION
14.4 Mounting Keypads and Zone Expansion Modules
LCD keypads have removable covers that allow you to easily mount the keypad to a wall or other flat surface
using the screw holes on each corner of the base. Before mounting the base, connect the keypad wire
harness leads to the keypad cable from the panel and to any device wiring run to that location. Then attach
the harness to the pin connector on the PC board, mount the base, and install the keypad cover making sure
all of the keys extend through their respective holes.
For mounting keypads on solid walls, or for applications where conduit is required, use the Model 695 1-1/2”
deep or the Model 696 1/2” deep backboxes.
The DMP 711, 712-8, 714, 715, 716, and 717 modules are each contained in molded plastic housings with
removable covers. The base provides you with mounting holes for installing the unit to a wall, switch plate,
or other surface.
14.5 Connecting LX-Bus and Keypad Bus Devices
Several factors determine the DMP LX-Bus™ and keypad bus performance characteristics: the wire length and
gauge used, the number of devices connected, and the voltage at each device. When planning an LX-Bus™
and keypad bus installation, keep in mind the following information:
1. DMP recommends using 18 or 22-gauge unshielded wire for all keypad and LX-Bus circuits. Do not use
twisted pair or shielded wire for LX-Bus and keypad bus data circuits.
2. On keypad bus circuits, to maintain auxiliary power integrity when using 22-gauge wire do not exceed 500
feet. When using 18-gauge wire do not exceed 1,000 feet. To increase the wire length or to add devices,
install an additional power supply that is UL listed for Fire Protective Signaling, power limited, and
regulated (12 VDC nominal) with battery backup.
Note: Each panel allows a specific number of supervised keypads. Add additional keypads in the
unsupervised mode. Refer to the panel installation guide for the specific number of supervised keypads
allowed.
3. Maximum distance for any one bus circuit (length of wire) is 2,500 feet regardless of the wire gauge. This
distance can be in the form of one long wire run or multiple branches with all wiring totaling no more
than 2,500 feet. As wire distance from the panel increases, DC voltage on the wire decreases. Maximum
number of LX-Bus devices per 2,500 feet circuit is 40. When using the on-board J22 LX-Bus, the
maximum number of LX-Bus devices per 2,500 foot circuit is 25. See J22 LX-Bus Expansion Connector
section later in this document.
4. Maximum voltage drop between the panel (or auxiliary power supply) and any device is 2.0 VDC. If the
voltage at any device is less than the required level, an auxiliary power supply should be added at the end
of the circuit.
For additional information refer to the LX-Bus/Keypad Bus Wiring Application Note (LT-2031) and/or 710/
710F Installation Sheet (LT-0310).
Expansion Interface Cards (Models 481, 462N, 462P, 462FM, and 472)
The LX-Bus provided on these cards requires only a 4-wire cable between the card and any devices
connected to the bus. You can connect devices (zone or output expansion modules) together on the same
cable or provide separate runs back to the card. Each LX-Bus provides up to 100 zones or outputs.
Note: Do not use twisted pair or shielded wire when connecting an LX-Bus or keypad bus.
XR2500F Installation Guide
Digital Monitoring Products
19
INSTALLATION
Battery Information
15.1 Battery Only Restart
When powering up the XR2500F panel without AC power, briefly short across the battery start pads to pull in
the battery cutoff relay. The leads need a momentary short only. Once the relay has pulled in, the battery
voltage holds it in that condition. If the XR2500F panel is powered up with an AC transformer, the battery
cutoff relay is pulled in automatically. For battery start pad location refer to Figure 11.
15.2 Battery Replacement Period
DMP recommends replacing the battery every 3 to 5 years under normal use.
15.3 Discharge/Recharge
The XR2500F battery charging circuit float charges at 13.9 VDC at a maximum current of 1.0 Amps using a
56 VA transformer. Listed below are the various battery voltage level conditions:
Battery Trouble:
Below 11.9 VDC
Battery Cutoff:
Below 10.2 VDC
Battery Restored:
Above 12.6 VDC
15.4 Battery Supervision
The XR2500F tests the battery when AC power is present. The test is done every three minutes and lasts for
five seconds. During the test, the panel places a load on the battery; if the battery voltage falls below 11.9
VDC a low battery is detected. If AC power is not present, a low battery is detected any time the battery
voltage falls below 11.9 VDC.
If a low battery is detected with AC power present, the test repeats every two minutes until the battery
charges above 12.6 VDC indicating the battery has restored voltage. If a weak battery is replaced with a
fully charged battery, the restored battery is not detected until the next two minute test completes.
15.5 Battery Cutoff
The panel disconnects the battery any time the battery voltage drops below 10.2 VDC. This prevents battery
deep discharge damage.
15.6 XR2500F Power Requirements
During AC power failure, the XR2500F panel and all auxiliary devices connected to the XR2500F draw their
power from the battery. All devices must be taken into consideration when calculating the battery standby
capacity. On the following page is a list of the XR2500F panel power requirements.
• XR2500F Command Processor™ Panel
• The Fire Command Center
• 893A Dual Phone Line Module
• Two 866 NAC modules
• 481 Zone Expansion Interface Card
Then add the additional current draw of Remote Fire Command Centers, Security Command® keypads, zone
expansion modules, smoke detector output, and any other auxiliary devices used in the system for the total
current required. The total is then multiplied by the number of standby hours required to calculate the total
ampere-hours required.
See the XR2500F Standby Battery Power Calculations chart on the following page and the Standby Battery
Selection information on the next page.
Digital Monitoring Products
20
XR2500F Installation Guide
INSTALLATION
15.7 XR2500F Standby Battery Calculations
Standby Battery Power Calculations
Standby Current
XR2500F Control Panel
Relay Outputs 1-2 (ON)
Switch Grounds 3-6 (ON)
Active Zones 1-8
Active Zones 9-10
2-Wire Smoke Detectors
Panel Bell Output
Qty
Qty
Qty
Qty
Qty
Qty
___ 1_
______
______
______
______
______
x
x
x
x
x
x
893A Dual Phone Line Module
Qty ______
x
461 Interface Adaptor Card
180mA
30mA
5mA
1.6mA
4mA
0.1mA
__180_mA
______
______
______
______
______
12mA ______
Alarm Current
Qty
Qty
Qty
Qty
Qty
Qty
____1_
______
______
______
______
______
x
x
x
x
x
x
Qty ______
x
50mA ______
x
7mA ______
7mA ______
180mA
30mA
5mA
*2mA
30mA
0.1mA
1500mA
__180_mA
______
______
______
______
______
______mA
462N Network Interface Card
Qty ______
x
50mA ______
Qty ______
x
50mA ______
462P Printer Interface Card
Qty ______
x
50mA ______
Qty ______
x
50mA ______
462FM 9600 Baud Modem
Qty ______
x
265mA ______
Qty ______
x
265mA ______
481 Expansion Interface Card
Qty ______
x
15mA ______
Qty ______
x
15mA ______
865 Style Y or Z Notification Module
Qty ______
x
26mA ______
Qty ______
x
85mA ______
866 Style W Notification Module
Qty ______
x
45mA ______
Qty ______
x
75mA ______
867 LX-Bus Style W Notification Module
Qty ______
x
30mA ______
Qty ______
x
85mA ______
630F Remote Fire Command Center
Qty ______
x
63mA ______
Qty ______
x
92mA ______
690/690F Security Command Keypad
Qty ______
x
77mA ______
Qty ______
x
84mA ______
693/793 Easy Entry Keypad
Active Zones (EOL Installed)
Qty ______
x
92mA ______
1.6mA ______
Qty ______
Qty ______
x
x
120mA ______
*2mA ______
790/790F Security Command Keypad
Active Zones (EOL Installed)
Qty ______
x
77mA ______
1.6mA ______
Qty ______
Qty ______
x
x
84mA ______
*2mA ______
791 Easy Entry Keypad
Active Zones (EOL Installed)
Qty ______
x
77mA ______
1.6mA ______
Qty ______
Qty ______
x
x
84mA ______
*2mA ______
7060 Thinline Keypad
Qty ______
x
80mA ______
Qty ______
x
84mA ______
7063 Thinline Keypad
Qty ______
x
86mA ______
Qty ______
x
112mA ______
7070 Thinline Keypad
Active Zones (EOL Installed)
Qty ______
x
72mA ______
1.6mA ______
Qty ______
Qty ______
x
x
87mA ______
*2mA ______
7073 Thinline Keypad
Active Zones (EOL Installed)
Qty ______
x
93mA ______
1.6mA ______
Qty ______
Qty ______
x
x
112mA ______
*2mA ______
733 Wiegand Interface Module
Active Zones (EOL Installed)
Annunciator (ON)
Qty ______
Qty ______
x
x
30mA ______
1.6mA ______
Qty ______
Qty ______
Qty ______
x
x
x
30mA ______
*2mA ______
20mA ______
734 Wiegand Interface Module
Active Zones (EOL Installed)
Annunciator (ON)
Qty ______
Qty ______
x
x
30mA ______
1.6mA ______
Qty ______
Qty ______
Qty ______
x
x
x
30mA ______
*2mA ______
20mA ______
Copy Sub-Totals to next page
*Based on 10% of active zones in alarm.
XR2500F Installation Guide
Sub-Total Standby ______mA
Sub-Total Alarm ______mA
Digital Monitoring Products
21
INSTALLATION
Standby Battery Power Calculations
736P POPIT Interface Module
Radionics Popex, POPITs, OctoPOPITs
710 Bus Splitter/Repeater Module
710F Fire Bus Splitter/Repeater Module
711, 714 Zone Expansion Modules
Active Zones (EOL Installed)
712-8 Zone Expansion Module
Active Zones (EOL Installed)
714-8, 714-16 Zone Expansion Module
Active Zones (EOL Installed)
715 Zone Expansion Module
Active Zones (EOL Installed)
2-Wire Smokes
715-8, 715-16 Zone Expansion Modules
Active Zones (EOL Installed)
2-Wire Smokes
716 Output Expansion Module
Active Form C Relays
717 Graphic Annunciator Module
Annunciator Outputs
521LX, 521LXT, SLRLX Smoke Detectors
Aux. Powered Devices on Terminals 7 and 11
Other than Keypads and LX-Bus Modules
This page only
Sub-Totals from previous page
*Based on 10% of active zones in alarm
Qty
Qty
Qty
Qty
Qty
Qty
Qty
Qty
Qty
Qty
Qty
Qty
Qty
Qty
Qty
Qty
Qty
Standby Current
______ x
25mA ______
______ x ___mA ______
______ x
30mA ______
______ x
40mA ______
______ x
7mA ______
______ x
1.6mA ______
______
x
19mA ______
______
x 1.6mA ______
______ x
20mA ______
______ x
1.6mA ______
______ x
7mA ______
______ x
4mA ______
______ x
.1mA ______
______ x
20mA ______
______ x
4mA ______
______ x
.1mA ______
______ x
7mA ______
Qty ______
x
Qty ______
x
10mA ______
8.8mA ______
______mA
Sub-Total Standby ______mA
Sub-Total Standby ______mA
Total Standby ______mA
Qty
Qty
Qty
Qty
Qty
Qty
Qty
Qty
Qty
Qty
Qty
Qty
Qty
Qty
Qty
Qty
Qty
Qty
Qty
Qty
Qty
Alarm Current
______ x
25mA ______
______ x ___mA ______
______ x
30mA ______
______ x
40mA ______
______ x
7mA ______
______ x
*2mA ______
______
x
19mA ______
______
x
*2mA ______
______ x
20mA ______
______ x
*2mA ______
______ x
7mA ______
______ x *30mA ______
______ x
.1mA ______
______ x
20mA ______
______ x *30mA ______
______ x
.1mA ______
______ x
7mA ______
______ x
28mA ______
______ x
10mA ______
______ x
1mA ______
______ x *28mA ______
______mA
Sub-Total Alarm ______mA
Sub-Total Alarm ______mA
Total Alarm ______mA
Total Standby______mA x number of Standby Hours needed ______ =
_______mA-hours
Total Alarm ______mA +_______mA-hours
Total _______mA-hours
X
.001
= _______Amp-hrs
Required
Refer to section 15.8 for standby battery selection.
Digital Monitoring Products
22
XR2500F Installation Guide
INSTALLATION
15.8 Standby Battery Selection
To choose the type and number of batteries needed for 24, 60, or 72 hours of standby power based on the
Amp Hours Required calculation from section 6.8 XR500 Series Power Requirements, perform the following:
1. Select the desired standby hours required from the table below: 24, 60, or 72 hours
2. Select the desired battery size: Model 368 (12 VDC 4.5 Ah), Model 369 (12 VDC 7 Ah),
Model 367 (12 VDC 7.7 Ah), Model 365 (12 VDC 9 Ah), Model 366 (12 VDC 18 Ah).
3. Select a Max. Ah Available number that is just greater than the number calculated as the Amp Hours
Required.
4. Install the number of batteries shown in the corresponding No. of Batteries required column.
Example: If the Amp Hours Required calculation equals 22 Ah for 24 hours of standby time and 4.5 Ah
batteries are desired, install six (6) Model 368 (12 VDC, 4.5 Ah) batteries.
For UL installations, all batteries shall be installed in a DMP Model 350 enclosure and all wiring shall run
through conduit. The enclosure shall be installed to the left of the XR500 Series enclosure to ensure
Battery and AC wire separation.
24 hours of standby power
4.5 Ah Batteries
7 Ah Batteries
7.7 Ah Batteries
9 Ah Batteries
18 Ah Batteries
Max. Ah No. of
Max. Ah No. of
Max. Ah No. of
Max. Ah No. of
Max. Ah No. of
Available Batteries
Available Batteries
Available Batteries
Available Batteries
Available Batteries
8
2
6
1
6
1
8
1
16
1
12
3
12
2
13
2
16
2
32
2
16
4
18
3
20
3
24
3
48
3
20
5
24
4
27
4
32
4
24
6
31
5
34
5
40
5
28
7
37
6
41
6
32
8
43
7
36
9
Note: 48 hours is the typical battery recharge time for any of the Number of
Batteries shown in this section.
40
10
60 hours of standby power
7 Ah Batteries
7.7 Ah Batteries
Max. Ah No. of
Max. Ah No. of
Available Batteries
Available Batteries
13
2
14
2
20
3
22
3
27
4
29
4
33
5
37
5
40
6
44
6
47
7
52
7
54
8
59
8
60
9
67
9
67
10
9 Ah Batteries
Max. Ah No. of
Available Batteries
17
2
26
3
34
4
43
5
52
6
61
7
69
8
18 Ah Batteries
Max. Ah No. of
Available Batteries
17
1
34
2
52
3
69
4
Note: 48 hours is the typical battery
recharge time for any of the Number
of Batteries shown in this section.
72 hours of standby power
9 Ah Batteries
18 Ah Batteries
Max. Ah No. of
Max. Ah No. of
Available Batteries
Available Batteries
16
2
16
1
25
3
33
2
33
4
50
3
42
5
67
4
50
6
59
7
Note: 72 hours is the typical battery recharge time required for any of the Number
of Batteries shown in this section.
67
8
Note: If the Amp Hours Required calculation is greater than any Max. Ah Available number shown on a table, then
add power supply(s) to power some system devices allowing the Amp Hours Required calculation to be reduced.
XR2500F Installation Guide
Digital Monitoring Products
23
INSTALLATION
Bell Output
16.1 Terminals 5 and 6
Terminal 5 supplies positive 12 VDC to power alarm bells or horns. This output can be steady, pulsed, or
temporal depending upon the Bell Action specified in Output Options. Terminal 6 is the ground reference
for the bell circuit. This supervised output detects 10k Ohms or less as normal. The indicating appliance
can supply this resistance. If using a horn or siren, a 1k Ohm 1/2 W EOL resistor (provided) should be added
across the bell circuit to provide supervision.
Keypad Bus
17.1 Description
XR2500F panel terminals 7, 8, 9, and 10 are for the keypad bus. In addition to Fire Command Centers and
Remote Fire Command Centers, you can connect up to sixteen supervised keypads and multiple unsupervised
keypads to the XR2500F. In addition to Security Command keypads, you can also connect any combination
of zone expansion modules, 5845LX Glassbreak detectors, and 6155LX PIRs to the data bus. Refer to the
specific device Installation sheet for the maximum number of keypad Bus devices.
Refer to the section titled LX-Bus for complete information about the LX-Bus 4-pin header and expansion
slot.
Note: Do not use shielded wire for LX-Bus/Keypad Bus circuits.
17.2 Terminal 7 - RED
This terminal supplies positive 12 VDC to power Fire Command Centers and zone expansion modules.
Terminal 7 also supplies power for any auxiliary device. The ground reference for terminal 7 is terminal 10.
The output current is shared with the smoke power output on terminal 11 and Zones 9 and 10. Current draw
for all connected devices must not exceed the panel maximum current rating.
17.3 Terminal 8 - YELLOW
Terminal 8 receives data from keypads and zone expansion modules. It cannot be used for any other
purpose.
17.4 Terminal 9 - GREEN
Terminal 9 transmits data to keypads and zone expansion modules. It cannot be used for any other purpose.
17.5 Terminal 10 - BLACK
Terminal 10 is the ground reference for Fire Command Centers, zone expansion modules, and all auxiliary
devices being powered by terminal 7.
17.6 J8 Programming Connection
A 4-pin header (J8) is provided to connect a keypad when using a DMP Model 330 Programming Cable. This
provides a quick and easy connection for panel programming.
You may also use the J8 Programming Header to connect Keypad Bus devices. This is an alternative to
connecting keypad bus devices to terminals 7, 8, 9, and 10.
17.7 OVC LED
The Overcurrent LED (OVC) lights Red when the devices connected to the Keypad Bus and LX-Bus(es) draw
more current than the panel is rated for. The OVC is located above Outputs 1 and 2 on the panel and turns a
steady Red when lit. When the OVC LED lights Red, the LX-Bus(es) and Keypad bus are shut down.
Digital Monitoring Products
24
XR2500F Installation Guide
INSTALLATION
Smoke and Glassbreak Detector Output
18.1 Terminals 11 and 12
Terminal 11 supplies positive 12 VDC to power 4-wire smoke detectors and other powered devices. This
output can be turned off by the user for five seconds using the Sensor Reset User Menu option to allow
latched devices to reset. Terminal 12 is the ground reference for terminal 11. See LT-0164 for a list of
approved 4-wire smoke detectors and power supervision relays.
18.2 Current Rating
The Output current from terminal 11 is shared with terminals 7, 25, and 27.
The total current draw of all devices powered from the panel must be included with terminal 11 calculations
and must not exceed the maximum output rating.
Powered Zones for 2-Wire Smoke Detectors
19.1 Terminals 25–26 and 27–28
Panel terminals 25 through 28 provide two resettable Class B, Style A, 2-wire powered zones. For
programming purposes the zone numbers are 9 and 10.
Note: The maximum wire length for either zone 9 or zone 10 is 3000 feet using 18 AWG or 1000 feet using 22
AWG.
When using 725 Zone Expansion Modules, use included, UL Listed 6.8k Ohm EOL resistors. The UL
compatibility identifier for the zones using 725 Zone Expansion Modules is B. When using 715 Zone
Expansion modules, use UL Listed 3.3k Ohm EOL resistors, Model 309. For all other zone expansion modules,
use UL Listed 1.0k Ohm Model 310 EOL resistors. The UL compatibility identifier for the zones is A.
Note: Do not mix detectors from different manufacturers on the same zone.
Caution: Performing a Sensor Reset momentarily drops power to the devices on Zones 9 and 10. The panel
views these zones (9 and 10) as “Open” while the power is absent.
XR2500F Installation Guide
Digital Monitoring Products
25
INSTALLATION
19.2 Compatible 2-Wire Smoke Detector Chart
Manufacturer
Model
Detector
ID
Base
Detection Systems
DS230, DS230F
B/A
MB2W, MB2WL
A
8.5-33
10
Detection Systems
DS250, DS250TH
B
MB2W, MB2WL
A
8.5-33
10/12
Detection Systems
DS250HD
B
MB2W, MB2WL
A
8.5-33
10
B/A
MB2W, MB2WL
A
8.5-33
17
8.5-33
10/12
715, 715-8,
715-16, 725
9 & 10
8-35
8-35
7/14
7/14
725
725
9 & 10
9 & 10
8-35
14
725
9 & 10
Detection Systems
DS260
DS282, DS282TH,
Detection Systems
DS282THC,
DS282THS
DMP/Hochiki
SLR-835
DMP/Hochiki
SLR-835B
SLR-835B-2
Hochiki
SLR-835BH-2
Hochiki
SLR-24, SLR-24H
SIJ-24, DCD-190,
Hochiki
DCD-135
Hochiki
SLR-24, SLR-24H
Hochiki
SIJ-24
Hochiki
DCD-190, DCD-135
429AT, 521B,
Sentrol/ESL
521BXT, 521NB,
521NBXT
429C, 429CT,
Sentrol/ESL
521B/BXT
429CRT, 429CST,
Sentrol/ESL
429CSST, 521CRXT
711U, 712U,
Sentrol/ESL
713-5U, 713-6U,
721U, 721UT
Base
DC
# of
Zone
Panel
ID
Voltage Detectors Expansion Zones
Range (12V/24V) Modules
B
HB-55
HD-6
N/A
HD-3
NS4-220
HB-3
15-33
15
725
9 & 10
HD-3
NS4-220
HB-3
15-33
15
725
9 & 10
HD-3
HD-3
HD-3
NS6-220
NS6-220
NS6-220
HB-3
HB-3
HB-3
15-33
15-33
15-33
15
20
16
725
725
725
9 & 10
9 & 10
9 & 10
S09A
6.5-20
12
715, 715-8,
715-16
9 & 10
S10A
8.5-33
12
725
S11A
8.5-33
12
725
S10A
701E, 70-1U,
702E, 702U
S00
8.5-33
12
725
701E, 701U,
702E, 702U,
702RE, 702RU
S00
8.5-33
12
725
8.5-35
10
S11A
System Sensor
1400
A
System Sensor
1151, 2151
A
B110PL, B401
8.5-35
10/10
System Sensor
1451, 2451TH
A
B401, B401B
8.5-35
10
System Sensor
1451DH
A
DH400
8.5-35
10
A
8.5-35
10
A
8.5-35
10
8.5-35
10
System Sensor
9 & 10
NS6-100
N/A
731U, 723U
2100T, 2100B,
2100TB, 2100D,
2100TD
2400, 2400AT,
2400AIT, 2400TH
9 & 10
HD-3
HD-6
Sentrol/ESL
System Sensor
725
715, 715-8,
715-16, 725
715, 715-8,
715-16
725
B401, B401B,
DH400
System Sensor
2451
A
System Sensor
2W-B, 2WT-B
A
8.5-35
10
System Sensor
DH100P, DH100LP
A
8.5-35
10
715, 715-8,
715-16
715, 715-8,
715-16, 725
715, 715-8,
715-16
715, 715-8,
715-16
715, 715-8,
715-16
715, 715-8,
715-16
715, 715-8,
715-16
715, 715-8,
715-16
715, 715-8,
715-16, 725
9 & 10
9 & 10
9 & 10
9 & 10
9 & 10
9 & 10
9 & 10
9 & 10
9 & 10
Table 6: Compatible 2-Wire Smoke Detectors
Digital Monitoring Products
26
XR2500F Installation Guide
INSTALLATION
Protection Zones
20.1 Terminals 13–24
Zones 1 to 8 (terminals 13 to 24) on the XR2500F panel are all grounded burglary zones. For programming
purposes, the zone numbers are 1 through 8. Listed below are terminal 13 to 24 connection functions.
Terminal
13
14
15
16
17
18
Function
Zone 1 voltage sensing
Ground for Zones 1 and 2
Zone 2 voltage sensing
Zone 3 voltage sensing
Ground for Zones 3 and 4
Zone 4 voltage sensing
Terminal
19
20
21
22
23
24
Function
Zone 5 voltage sensing
Ground for Zones 5 and 6
Zone 6 voltage sensing
Zone 7 voltage sensing
Ground for Zones 7 and 8
Zone 8 voltage sensing
Note: Zones 1 through 4 have been pre-wired to the two 866 NAC modules and the 504-24 power supply. All
other zones are available.
The voltage sensing terminal measures the voltage across a 1k Ohm End-of-Line resistor to ground. Use
DMP Model 311 1k Ohm resistors. Dry contact sensing devices can be used in series (normally-closed) or in
parallel (normally-open) with any of the burglary protection zones.
1K Ohm
Normally
Closed
1K Ohm
Normally Open
1K Ohm
Combination Normally Open
and Normally Closed
Figure 12: Protection Zone Wiring
20.2 Operational Parameters
Each protection zone detects three conditions: Open, Normal, and Short. Listed below are voltage and
resistance parameters for each condition:
Condition
Open
Normal
Short
Resistance on zone
over 1300 Ohms
600 to 1300 Ohms
under 600 Ohms
Voltage on positive terminal
over 2.0 VDC
1.2 to 2.0 VDC
under 1.2 VDC
20.3 Zone Response Time
A condition must be present on a zone for 500 milliseconds before it is detected by the XR2500F panel.
Ensure detection devices used on the protection zones are rated for use with this delay. Zones 1-10 can also
be programmed for a fast response delay of 160 milliseconds.
20.4 Keyswitch Arming Zone
Using a keyswitch on an Arming type zone allows you to arm and disarm selected areas without having to
enter a user code.
XR2500F Installation Guide
Digital Monitoring Products
27
INSTALLATION
Dry Contact Relay Outputs
21.1 Description
The XR2500F panel provides two auxiliary SPDT relays with the two DMP Model 305 relays in K6 (Output 1)
and K7 (Output 2) and a Model 431 Output Harness on the J2 6-pin Header. Each relay provides one SPDT set
of contacts that can be operated by any of the functions listed below:
1) Activation by zone condition: Steady, Pulsing, Momentary, and Follow
2) Activation by 24-hour 7-day schedule: One on and one off time a day for each relay
3) Manual activation from the Security Command keypad menu
4) Communication failure
5) Armed area annunciation
6) Fire Alarm or Fire Trouble
7) Ambush Alarm
8) Exit and Entry timers
9) System Ready
10) Late to Close
Refer to the XR500 Series Programming Guide (LT-0679) for specific information.
21.2 Contact Rating
The Model 305 relay contacts are rated for 1 Amp at 30 VDC resistive. You can connect auxiliary power to
the Relay Output 1 common terminal by installing the gray harness wire to terminal 7. Current draw for all
connected devices must not exceed the panel maximum current rating.
21.3 Output Harness Wiring
The Output Harness is pre-installed on the 6-pin header labeled J2. Output 2 uses the top three prongs,
and Output 1 uses the bottom three prongs. Outputs 1 and 2 are prewired to the 866 NAC modules located
within the XR2500F enclosure. For reference, the wire harness and contact locations are shown below:
Contact
Color
Output 1 normally closed
Violet
Output 1 common
Gray
Output 1 normally open
Orange
Output 2 normally closed
Blue
Output 2 common
White
Output 2 normally open
Yellow
Digital Monitoring Products
28
XR2500F Installation Guide
INSTALLATION
J11 Annunciator Outputs
22.1 Description
The four annunciator outputs can be programmed to indicate the activity of the panel zones or conditions
occurring on the system. Annunciator outputs do not provide a voltage but instead switch-to-ground a
voltage from another source. The outputs can respond to any of the conditions listed in section 22.1.
22.2 Model 300 Harness Wiring
Access the open collector outputs by installing DMP 300 Harness on the 4-pin header labeled J11. The
output locations are shown below. For UL applications, devices connected to the outputs must be located
within the same room as the panel.
Output
3
4
Color
Red
Yellow
Wire
1
2
Output
5
6
Color
Green
Black
Wire
3
4
22.3 Model 860 Relay Module
Connect a Model 860 Relay Module to the J11 on the XR2500F panel to provide relays for outputs 3-6. Use
these relays for electrical isolation between the alarm panel and other systems or for switching voltage
to control various functions. Power is supplied to the relay coils from a single wire connected to the
panel auxiliary power terminal 7. The module includes one relay and provides three additional sockets for
expansion of up to four relays. Mount the 860 inside the panel enclosure using the 3-hole pattern and plastic
standoffs. Refer to the 860 Module Install Sheet (LT-0484) as needed.
Model 305 Relay Contact Rating:
1 Amp at 30 VDC
J23 6-Pin Header
23.1 Description
The XR2500F Command Processor™ panel supports RS-232, LX-Bus and future expansion operation. These
operations cannot function at the same time. Install a jumper on one pair of J23 headers to indicate how
the panel is programmed to operate. Refer to the table below when installing a jumper on J23. When a
jumper is installed or moved on the 6-pin header, briefly reset the panel using the J16 jumper to activate
the selected operation.
J23 6-Pin Header
Letter
Operation
R
Standard RS-232
L
LX-Bus
X
Future Expansion
J21
R
L
X
J23
RS-232
J22
LX-Bus
LEDs
Xmit
Receive
Overcurrent
LED
Figure 14: J23 6-Pin Header
XR2500F Installation Guide
Digital Monitoring Products
29
INSTALLATION
J22 LX-Bus Expansion Connector
24.1 Description
J22 LX-Bus and J21 RS-232 connectors cannot be used at the same time. Either use J21 to connect a serial
device for PC Log Reporting, or use J22 to connect an LX-Bus device. This is determined by where you install
the jumper on J23 6-Pin Header. Reset the panel using J16 jumper to activate selected J23 operation.
Note: Do NOT use shielded wire when using the LX-Bus. Do NOT connect the wires from the 4-wire harness
to the panel terminals.
24.2 LX-Bus Interface Cards
Refer to the following tables to identify zone locations and numbers relative to J22 operation.
J22 LX-Bus Enabled
LX-Bus Zone Numbers
AND
1
500-599
One Interface Card
LX-Bus Zone Numbers
OR
2
600-699
One Interface Card
J22
LX-Bus
NOT
Enabled
LX-Bus Zone Numbers
1
500-599
OR
461 Adaptor Card and
Multiple Interface
Cards
LX-Bus Zone Numbers
2 (A)
600-699
3 (B)
700-799
4 (C)
800-899
5 (D)
900-999
461 Adaptor Card and
Multiple Interface
Cards
LX-Bus Zone Numbers
1 (A)
500-599
2 (B)
600-699
3 (C)
700-799
4 (D)
800-899
5 (E)
900-999
24.3 LX-Bus LEDs
The two LEDs, located near the bottom-right corner of J21 indicate data transmission and receipt. The
top LED flashes green to indicate the panel is transmitting LX-Bus data. The bottom LED flashes yellow to
indicate the panel is receiving LX-Bus data.
24.4. OVC LED
The Overcurrent LED (OVC) lights Red when the devices connected to the Keypad Bus and LX-Bus(es) draw
more current than the panel is rated for. The OVC is located above Outputs 1 and 2 on the panel and turns a
steady Red when lit. When the OVC LED lights Red, the LX-Bus(es) and keypad bus shut down.
J21 Serial Connector
25.1 Description
Note: J22 LX-Bus and J21 RS-232 connectors cannot be used at the same time. Either use J21 to connect a
serial device, or use J22 to connect an LX-Bus device. This is determined by where you install the jumper on
the J23 6-Pin Header. Reset the panel using J16 jumper to activate selected J23 operation.
To enable J21 to operate in RS-232 mode place a jumper on the two pins next to the letter “R” on the J23
6-Pin header. The Serial Connector allows the XR2500F panel to transmit PC Log Reports directly to an
RS-232 device.
25.2 Serial Connector LEDs
The two LEDs, located near the bottom-right corner of J21 indicate data transmission and receipt. The
top LED flashes green to indicate the panel is transmitting serial data. The bottom LED flashes yellow to
indicate the panel is receiving serial data.
Digital Monitoring Products
30
XR2500F Installation Guide
INSTALLATION
J1 Ethernet Connector
26.1 Description
The J1 Ethernet Connector is available to connect directly to an Ethernet network using a standard patch
cable.
J1
Ethernet
Link LED
Activity LED
Figure 15: J1 Header and LEDs
26.2 Ethernet LEDs
The two LEDs, located to the left of J1 Ethernet Connector, indicate network operation. The top, Activity
LED flashes green to indicate the network traffic is good. The bottom, Link LED flashes yellow to indicate
messages are being sent and received.
Reset and Tamper Headers
27.1 J16 Reset Header
The reset header is located just above the terminal strip on the right side of the circuit board and is used
to reset the XR2500F microprocessor. To reset the panel when first installing the system, install the reset
jumper before applying power to the panel. After connecting the AC and battery, remove the reset jumper.
To reset the panel while the system is operational, for example, prior to reprogramming, install the reset
jumper without powering down the system. Remove the reset jumper after one or two seconds.
After resetting the panel, begin programming within 30 minutes. If you wait longer than 30 minutes, you
must reset the panel again.
��
����������
��
������
��������
������������
����������������������������
����������������������������
������������������������
��
��������
���
������
���
������
�
��������
��
���
��������
�����
���
��
��
����
��������
���� ����
������ ���
�
���
�
�� �� �� �� ���� ��� ��� ��� ��� ��� ��� ��� �� ��� ��
�
�
�
�
�
�
�
�
�
���
����������
�����
����������
���������
��
��
�� ��
��
��
���
��
��
��
�
���
�����
�����������
�� ��� �� �� ��� ��
�� ��
�� ��
��
��
�� ��� �� ��� ��� ���� ����
�� ��
��
��
��
��
��
��
Figure 16: XR2500F Panel Showing the Reset Jumper
27.2 J4 Tamper Header
The J4 header is for use with the optional DMP 306 Tamper Harness. The harness connects to one or more
tamper switches mounted inside the panel enclosure to supervise against unauthorized enclosure opening or
removal. Refer to the wiring diagram on the enclosure door for correct tamper switch wiring.
How the Tamper Works
If the enclosure is opened or removed while one or more of the system areas are armed, a panel tamper
alarm is indicated. If all areas are disarmed, a panel tamper trouble is indicated.
XR2500F Installation Guide
Digital Monitoring Products
31
COMPLIANCE
Universal UL Burglary Specifications
28.1 Introduction
The programming and installation specifications contained in this section must be completed when installing
the XR2500F panel in accordance with any of the UL burglary standards. Additional specifications may be
required by a particular standard.
28.2 Wiring
All wiring must be in accordance with NEC, ANSI/NFPA 70, UL 681. All transformer wires must be installed in
conduit.
28.3 Control Outside of Protected Area
A Potter EVD or Sentrol 5402 should be used in place of a lined cabinet when the panel is installed outside
of the protected area. Front and rear tamper switches are required. Refer to the system wiring diagram
and Figure 2.
28.4 Police Station Phone Numbers
The digital dialer telephone number programmed for communication must not be a police station phone
number.
28.5 System Maintenance
To ensure continuous satisfactory operation of any alarm system, proper installation and regular
maintenance by the installing alarm company and frequent testing by the end user is essential. Offering a
maintenance program and acquainting the user with the correct procedures for system use and testing is
also the responsibility of the installing alarm company.
28.6 UL Listed Receivers
UL has verified operation with the DMP SCS-1 and SCS-1R, Sur-Gard SG-HLR2-DG, FBII CP220PB, OsborneHoffman Quick-Alert, and Radionics D6500 receivers. It is the installer’s responsibility to verify compatibility
between the XR2500F and the receiver used during installation. The installer shall verify the compatibility
of the receiver and the system on a yearly basis.
Area Information
29.1 Ownership
The control unit system shall be under one ownership.
29.2 Annunciation
The System shall be installed so that when arming any area from any keypad, the local bell shall annunciate.
29.3 Trouble Display
The Status List programming shall be set to annunciate all trouble messages at all keypads. See the XR500
Series Programming Guide (LT-0679).
29.4 Closing Wait
The Closing Wait option must be programmed YES. See the XR500 Series Programming Guide (LT-0679).
29.5 Local Bell Supervision
When a local bell is employed, the power supply for the bell shall be under 24-hour protection. Proper
personnel for maintenance or security of the system shall be able to disarm that area.
Digital Monitoring Products
32
XR2500F Installation Guide
COMPLIANCE
UL 1023 Specifications
Household Burglar-Alarm System Units
30.1 Audible Devices
At least one listed audible device (Ademco AB12M) rated to operate over the voltage rate of 11.7 VDC to
12.8 VDC and rated at 85 DB minimum must be used.
30.2 Auxiliary Circuits
At least one burglary alarm initiating device shall be used on the system. If the voltage for the device is
applied by the control unit the burglary alarm initiating device shall be rated to operate over the range of
11.5 VDC to 12.7 VDC.
30.3 Bell Cutoff
The Bell Cutoff time cannot be less than five minutes. See the XR500 Series Programming Guide (LT-0679).
30.4 Entry Delay
The maximum entry delay used must not be more than 45 seconds. See the XR500 Series Programming Guide
(LT-0679).
30.5 Exit Delay
The maximum exit delay used must not be more than 60 seconds. See the XR500 Series Programming Guide
(LT-0679).
30.6 Weekly Test
The product should be tested weekly.
UL 1635 Specifications
Digital Burglar Alarm Communicator System Units
31.1 System Trouble Display
The Status List Display must include at least one keypad that displays system monitor troubles. See the
XR500 Series Programming Guide (LT-0679).
31.2 Digital Dialer Telephone Number
Both programmed telephone numbers must begin with a P. See the XR500 Series Programming Guide
(LT-0679).
31.3 Test Time
The Test Time option must be programmed so that the XR2500F sends a report once every 24 hours. See the
XR500 Series Programming Guide (LT-0679).
31.4 Closing Wait
The Closing Wait option must be programmed YES. See the XR500 Series Programming Guide (LT-0679).
31.5 Entry Delay
The maximum entry delay used must not be more than 60 seconds. See the XR500 Series Programming Guide
(LT-0679).
31.6 Exit Delay
The maximum exit delay used must not be more than 60 seconds. See the XR500 Series Programming Guide
(LT-0679).
XR2500F Installation Guide
Digital Monitoring Products
33
COMPLIANCE
UL 1610 AND 1076 Specifications
Central-Station and Proprietary Burglar-Alarm Units
32.1 Opening/Closing Reports
The Opening/Closing Reports option must be programmed as YES. See the XR500 Series Programming Guide
(LT-0679).
32.2 Closing Wait
The Closing Wait option must be programmed YES. See the XR500 Series Programming Guide (LT-0679).
32.3 Entry Delay
The maximum entry delay used must not be more than 60 seconds. See the XR500 Series Programming Guide
(LT-0679).
32.4 Exit Delay
The maximum exit delay used must not be more than 60 seconds. See the XR500 Series Programming Guide
(LT-0679).
32.5 Proprietary Dialer
The Model XR2500F provides Grade A proprietary service when configured as a digital dialer.
32.6 Grade B Central Station
Grade B Central Station service can be provided under by adding a Grade A Ademco AB12M bell and bell
housing.
32.7 Bell Cutoff
The Bell Cutoff time cannot be less than 15 minutes. See the XR500 Series Programming Guide (LT-0679).
32.8 AA Network Communication
High Line Security is provided when configured as a NET system using an XR500N panel or an XR500 panel
with an iCOM™ Internet Alarm Router. The NET Check-in time must be set from 01 to 06 minutes or AA.
When a dialer is required for 06 minute check-in time, an attack resistant enclosure (DMP Model 350A) is
required. When the check-in time is set to a number less than 200 seconds, an attack resistant enclosure is
not required. See sections 3.2, 3.2.1, and 3.3 of the XR500 Series Programming Guide (LT-0679).
To provide High Line Encrypted security, install an XR500E panel or an XR500 panel with an iCOM-E™
Encrypted Network Alarm Router.
For high line security operation, communication between the Premise and Supervising Station provides 128
bit encryption when using an XR500E panel or an XR500 panel with an iCOM-E Encrypted Network Alarm
Router.
The Model XR500 Series Protected Premises Control Unit is suitable for Grade AA service when configured for
NET communication with SCS-1/SCS-1R receiving system. This configuration is approved for the following:
AMCX - Central Station Alarm Units
APOU - Proprietary Alarm Units
Digital Monitoring Products
34
XR2500F Installation Guide
COMPLIANCE
UL 365 and 609 Specifications
Police Station Connected and Local Burglar Alarm Units and Systems
33.1 System Trouble Display
The Status List Display must include at least one keypad that displays system monitor troubles. See the
XR500 Series Programming Guide (LT-0679).
33.2 Entry Delay
The maximum entry delay used must not be more than 60 seconds. See the XR500 Series Programing Guide
(LT-0679).
33.3 Exit Delay
The maximum exit delay used must not be more than 60 seconds. See the XR500 Series Programming Guide
(LT-0679).
33.4 Grade A Bell
A Grade A local audible signal appliance must be used such as Ademco AB12M bell and bell housing.
33.5 Bell Cutoff
The Bell Cutoff time cannot be less than 15 minutes. See the XR500 Series Programming Guide (LT-0679).
33.6 Automatic Bell Test
The Automatic Bell Test option must be programmed as YES. See the XR500 Series Programming Guide
(LT-0679).
33.7 Line Security for Police Connect
Basic line security is provided when the Model XR2500F is configured as a dialer system.
33.8 High Line Security
High Line Security is provided when configured as a NET system using an XR500N panel or an XR500 panel
with an iCOM™ Internet Alarm Router. The NET Check-in time must be set from 01 to 06 minutes or AA.
When a dialer is required for 06 minute check-in time, an attack resistant enclosure (DMP Model 350A) is
required. When the check-in time is set to a number less than 200 seconds, an attack resistant enclosure is
not required. See sections 3.2, 3.2.1, and 3.3 of the XR500 Series Programming Guide (LT-0679).
To provide High Line Encrypted security, install an XR500E panel or an XR500 panel with an iCOM-E™
Encrypted Network Alarm Router.
For high line security operation, communication between the Premise and Supervising Station provides 128
bit encryption when using an XR500E panel or an XR500 panel with an iCOM-E Encrypted Network Alarm
Router.
UL 294 Specifications
34.1 Panel Designation
The XR2500F is designated as a stand alone unit.
34.2 Compatible Devices
The following devices are compatible with the XR2500F panels.
Access Control
733 Wiegand Interface Module
734 Wiegand Interface Module
OP-08CB Motion Detector
* PB-2 REX Button
PP-6005B Proxpoint Plus® Reader
MP-5365 Miniprox® Reader
PR-5455 ProxPro® II Reader
MX-5375 Maxi-Prox™ Reader
Proximity reader connector
Programmable proximity reader connector
Infrared sensor.
Exit control push button
Proximity reader
Slimline proximity reader
Long range reader with sounder
Long range reader compatible with 1351 Prox Pass
* This device has not been investigated by UL and shall not be used in UL installations.
XR2500F Installation Guide
Digital Monitoring Products
35
COMPLIANCE
Universal UL and NFPA Fire Alarm Specifications
35.1 Introduction
The programming and installation specifications contained in this section must be completed when installing
the Model XR2500F in accordance with any of the UL or NFPA fire standards. Additional specifications may be
required by a particular standard.
35.2 Wiring
All wiring must be in accordance with NEC, ANSI/NFPA 70.
35.3 Transformer
A wire-in transformer should be used. Use the supplied 16 VAC 56 VA transformer. The transformer must be
mounted within 20 feet of the panel and connected by conduit.
35.4 End-of-Line Resistor
The DMP Model 310 1K Ohm EOL resistor should be used on all 1K Ohm EOL fire zones.
35.5 System Trouble Display
The Status List Display must include at least one keypad that displays system monitor troubles. See the
XR500 Series Programming Guide (LT-0679).
35.6 Fire Display
The Status List Display must include at least one keypad that displays troubles and alarms on fire type zones.
See the XR500 Series Programming Guide (LT-0679).
35.7 Police Station Phone Number
The digital dialer telephone number programmed for communication must not be a police station phone
number, unless that phone number is specifically provided for that purpose.
35.8 System Maintenance
To ensure continuous satisfactory operation of any alarm system, proper installation and regular
maintenance by the installing alarm company and frequent testing by the end user is essential. Offering a
maintenance program and acquainting the user with the correct procedures for system use and testing is
also the responsibility of the installing alarm company.
35.9 Audible Alarm
Fire Type zones must be programmed to activate an audible alarm. The Bell Action for Fire Type zones must
not be programmed as “N”. See the XR500 Series Programming Guide (LT-0679).
35.10 Fire Zone Programming
If a retard delay is used on a waterflow zone, it cannot exceed 90 seconds and any retard delay in the
waterflow initiating devices must be subtracted from the 90 seconds allowed. See the XR500 Series
Programming Guide (LT-0679). The retard delay should not be used on a zone with smoke detectors.
35.11 Style D Zones
If required, the DMP 869 Dual Style D Initiating Module provides for connection of two Style D zones to the
Model XR2500F. See the 869 Installation Guide (LT-0186) and sections 29.2 and 37.2 of this guide for wiring
information.
35.12 Video Option
The Video option must be selected as NO when any fire protection is connected to the XR2500F. See the
XR500 Series Programming Guide (LT-0679).
35.13 UL Listed Receivers
Use the DMP SCS-1/SCS-1R (SDLC), Sur-Gard SG-HLR2-DG (CID), FBII CP220PB (CID), and Osborne-Hoffman
Quick-Alert (CID) receivers.
Digital Monitoring Products
36
XR2500F Installation Guide
COMPLIANCE
UL 864 NFPA 72 (Chapter 9) Specifications
Control Units for Fire-Protective Signaling Systems
36.1 Zone Restoral Reports
The Restoral Reports option must be selected as YES or Disarm. See the XR500 Series Programming Guide
(LT-0679).
36.2 Power Fail Delay
The Power Fail Delay option must be selected as required by the service of the panel. For Central Station
service: 6-12, for Remote Station service: 12-15. See the XR500 Series Programming Guide (LT-0679).
36.3 Sprinkler Supervisory
Any zone used for sprinkler supervisory must be programmed with “SPRINKLR XXX” as the zone name. The
last three characters in the zone name may be assigned a number to identify the zone. The Model 893A Dual
Phone Line Module must be used on all sprinkler supervisory systems.
36.4 DACT Systems
Two phone lines must be used. The two phone lines cannot be ground start or party lines. The 893A Dual
Phone Line Module is used to provide two phone line connections to the system. The 2ND Phone Line
communication option must be selected as DD. See the XR500 Series Programming Guide (LT-0679).
Two different phone numbers must be programmed for digital communication. See the XR500 Series
Programming Guide (LT-0679). The Test Time option must be programmed so that the XR2500F sends a report
every 24 hours. See the XR500 Series Programming Guide (LT-0679).
36.5 Local Protective Signaling Systems
The DMP Model 865, 866, or 867 Notification Circuit Module must be used on the bell circuit for detection of
shorts and grounds. See sections 32.1 to 32.2 in this guide for wiring diagrams. Model 690/690F, 790/790F,
793, 630F keypads that are used to display troubles for local fire alarm systems must be installed within a
DMP Model 777 with 777S 1.0” spacer. Any burglary or other off premises communication must be done with
the Model 893A Dual Phone Line Module. For local commercial fire installations, the 893A is required.
36.6 Remote Station Protective Signaling Systems
You must provide 60 hours of standby battery. See section 16.9 in this guide for standby battery
calculations. Two Radionics Model D127 Reversing Relay Modules provide two reversing polarity telephone
connections. See the D127 Installation Instruction sheet for wiring details. A DMP Model 893A is used to
provide two line dialer communication.
36.7 Fire Protective Signaling Systems
The XR2500F Panel must be programmed as described below for Fire Protective Signaling Systems using
Internet or Intranet network alarm communication.
• UL AA must be programmed as NO
• SUB CODE must be programmed as YES
• CHECKIN must be programmed as 1
• RETRY TIME must be programmed as 1
• FAIL TIME must be programmed as 1
• NET TRBL must be programmed as YES
XR2500F Installation Guide
Digital Monitoring Products
37
COMPLIANCE
UL 985 NFPA 72 (Chapter 2) Specifications
Household Fire Warning System Units
37.1 Bell Output Definition
The Model XR2500F panel Bell Output must be programmed to operate steady on burglary alarms and pulsed
or temporal on fire alarms. See the XR500 Series Programming Guide (LT-0679).
37.2 Audible Devices
At least one listed audible device rated to operate over the voltage rate of 11.7 VDC to 12.8 VDC and rated
at 85 DB minimum must be used.
37.3 Auxiliary Circuits
At least one fire alarm initiating device shall be used on the system. If the voltage for the device is applied
by the control unit the fire alarm initiating device shall be rated to operate over the range of 11.5 VDC to
12.7 VDC.
37.4 Bell Cutoff
The Bell Cutoff time cannot be less than five minutes. See the XR500 Series Programming Guide (LT-0679).
California State Fire Marshal Specifications
38.1 Bell Output Definition
The Model XR2500F panel Bell Output must be programmed to operate steady on burglary alarms and pulsed,
temporal, or California School Code on fire alarms. See the XR500 Series Programming Guide (LT-0679).
New York City (MEA) Specifications
39.1 Introduction
The programming and installation specifications contained in this section must be completed when installing
the XR500 Series panel for New York City (MEA) fire alarm installations that provide a digital dialer with
network IP communication as backup. Fire alarm installations that use two digital dialer telephone lines do
not need to comply with these specifications.
39.2 Digital Dialer and Network Communication
When used with a central office communicator or a transmitter, the installation and operation of the
equipment and devices shall comply with 3RCNY 17-01. The installation shall employ the digital dialer as
the primary communicator (using telephone line) with network IP communication as backup or secondary
means of communication. It shall have the capability of transmitting separate and distinct signals to
indicate manual pull station alarm, automatic detection alarm, sprinkler waterflow alarm, supervisory signal
indications and trouble indications.
39.3 Wiring
All wiring must be in accordance with NEC, ANSI, and NFPA 70. All network cabling must be installed in
accordance with NFPA 70 for communication circuits.
39.4 Communication Programming
For digital dialer communication with supervised network backup, program the following:
COMM TYPE = NET
SECOND LINE = DD
RECEIVER 1
ALARMS = YES
FIRST PHONE NUMBER = Central Station Receiver Phone Number
RECEIVER 2
ALARMS = YES
FIRST PHONE NUMBER = Central Station Receiver Phone Number
See the XR500 Series Programming Guide (LT-0679).
39.5 Additional Requirements
Program and install the equipment to comply with NFPA basic fire requirements. Refer to the Universal UL
and NFPA Fire Alarm Specifications and UL 864 NFPA 72 (Chapter 9) Specifications earlier in this document.
Digital Monitoring Products
38
XR2500F Installation Guide
XR2500F Installation Guide
����
����������
������
������
���������������������������
�������������
������������
���������
�����
����������
���������������
���������������
��������������
��������������
��������������
��������������
���������������
���������������
����
������
���������������������
���������������������
������������
���������
����
�������
���������
�����
����������
�������������
������������
������������
��������������
��������������
����
������
���������������������
���������������������������
�������������
������������
�
�
�
�
������
�
�
�
�
�����������
����������
�������������
����������
���������
����
�������
����
����������
������
������
�
�
�
�
�
�
�������������
��������
������������
���������������������������������
������������������������������������
����������������������������������
�����������������������������������
������������������
�������
�������
�������������
����������������������
�������������������
��������������������������������������������������������������������������������
�����������������������������������������������������������������������������
��������������������������������������������������������������������
���
���
��
���
���
������
��
��
�
�
�
�
�����������
����������
�������������
����������
�
�
�
�
�
�
��
��
�� ��
��
�� ��
���������������������������������
������������������������������������
����������������������������������
�����������������������������������
������������������
�
���
�
��
�������������������������������������������������������������������������
���������������������������������������������������������������
�
�� ��
��
��
��
� ��������������������
��
��
��
��
�� ��� �� ��� ��� ���� ����
���
�����
��
����������
�����
����������
���������
���������������������������������
�������������������������������
������������������������������������
��������������������������������
�������������������������������
������������������������������������
���������������������������������
�������������������������
������������������������������
�� ��
�� ��� �� �� ��� ��
��
��������
�������������������
�����
������������������������������������������������������������������������
�������������������������������������������������������������
�
�
�������
�
�
�
�
�
��
��
������
�� �� �� �� ���� ��� ��� ��� ��� ��� ��� ��� �� ��� ��
��������
�����
��
COMPLIANCE
Wiring Diagrams
40.1 Multiple Notification Circuit Modules
Digital Monitoring Products
39
COMPLIANCE
��
������
��
��������
�������������������
�����
���
����������
�����
����������
���������
��
���
�����������������
�����������������������������������
��������������������������������������
���
�
�
�
������������������������������������������
����������
���������������������������������������
���������������������������������������
���������������������������������
���
��
�� �� �� �� ���� ��� ��� ��� ��� ��� ��� ��� �� ��� ��
�
�
�
�
�
�
�
�
�
�
��
��������������������
��������������
�������������
�������������
���
�����
��
�� ��
��
�� ��� �� �� ��� ��
�� ��
��
�� ��
��
�� ��� �� ��� ��� ���� ����
�� ��
��
�� ��
� �
�
�
�������
�
�
�
������
�
����
�������
������
������
�����������
����������
�������������
����������
�������
�������������
����������
���������
�����
����������
�������������
������������
������������
��������������
��������������
���������������������������������
������������������������������������
����
����������������������������������
���������
�������
�����������������������������������
����
������
������������������
�������
������
���������������������
������������
�������
������
������
����
��
��������������
�������
����
���������������������
�
�
��
�������������
��������
����
������
��������������������
��������������
�������������
�������������
�������
�������������
��
�������������
��������
����
������
�
� ��������������������
���������������������
��������
������
�������
���
� �
�
��������
������
�������
��
��
�����������������������������������
���������������������������������������
������������������������������������
����������
���������
�����
����������
�������������
������������
������������
��������������
��������������
��
���
��������
�����
���������������������������������
40.2 Multiple Notification Circuit Modules for Zoned Annunciation
�������
�����������
����������
�������������
����������
������
�������������������������������
�����������������������������������������
����������������������������������������
���������������������
���������������������
������������
���������������������
�
����������
���������
�����
����������
���������������
���������������
��������������
��������������
��������������
��������������
���������������
���������������
��������������������
��������������
�������������
�������������
�
�������
�
�����������
����������
�������������
����������
�
�
�
�
�
�
�
���������������������������
����������������
Digital Monitoring Products
40
���������������������������������
������������������������������������
����������������������������������
�����������������������������������
������������������
�������������������������������
������������������������������������
��������������������������������
������������������������������������
��������������������������������������
��������������������������������������
�������������������������������
������������
��������������������������������������
�����������������������������������
���������������������������������
�������������������������������
XR2500F Installation Guide
WIRING DIAGRAMS
��
������
��
���
����������
�����
����������
���������
��������
�������������������
�����
��
���
���
������
�
�
�
���
��
���
��������
�����
��
��
���
���
�����
��
�� �� �� �� ���� ��� ��� ��� ��� ��� ��� ��� �� ��� ��
������������������������������
�������������
������������������������
��������
�
�
�
�
�
�
���������������������������������
40.3 Dual Style D Zone Module Installation
�
�
�
�
�
��
��
�� ��
�
��
�� ��� �� �� ��� ��
�� ��
�� ��
��
��
��
�� ��� �� ��� ��� ���� ����
��
��
��
��
��
��
��
�
���������
����
��������
��
��
��
��
������
���
���������
������
��
��
������
��
��
������
����������������������
�
�
�
�
�
�
�
������������������������������������������������������
����������������������������������������������������
�
����
�������
XR2500F Installation Guide
Digital Monitoring Products
41
WIRING DIAGRAMS
��������
�������������������
�����
��
������
��
���
����������
�����
����������
���������
��
���
�����������������
�����������������������������������
�����������������������������������
������
���
��
�
��
��
�
��
����� �����
��
��
�� �� �� �� ���� ��� ��� ��� ��� ��� ��� ��� �� ��� ��
�
�
�
�
�
�
�
�
�
��
���������
��������������
��
���
��������
�����
��
�� ��
��
���
��
��
��
�
�����������
���
�
�
�
���
�����
�� ��� �� �� ��� ��
�� ��
�� ��
��
��
���������������������������������
40.4 Remote Station Reversing Relay Connection
�� ��� �� ��� ��� ��������
�� ��
��
��
��
��
��
��
�
�
�
�
� ��������������������
�����
���
�
�
�
�
�
�������������������������������������������������������
��������������������������������������������
���
�
�����
������������������������������������������������
�������������������������������������������������
��������������������������������������������������������
�
�
�
��������������������������������������������������
�������������������������������������������������
���������������������������������������������������
�����������������������������������������
����������������������
��������������������
������������������������
�������
���������������
�����������
������������������
�������������������
��������������������
��������������������
�������������������
������������
������
������
����������������������
������������
�����������������
�����������������������������
�������������������������������
������������������������������
��������������������������
���������������
�����������
������������������
�������������������
��������������������
��������������������
�������������������
������������
�����������������������������������
������
���������������������������������
���������������������������������
������
������������������������
������������
�����������������
����������������������
��������������������
������������������������
�������
Digital Monitoring Products
42
XR2500F Installation Guide
WIRING DIAGRAMS
40.5 Second LX-Bus™ with Auxiliary Power Supply
�����������������������
����������������������������
�����������������������
�
�
�
�
�
��
������
��
����������
���
�������
��������
����������������
��
��������
���
���
������
�
�
�
���
������
��������
��������
���
��
��������
�����
��
����
���������
���
��
��
��
��
�
��
����
��
��
��
��
�
�
�
�
���� ��� ��� ���
�
�
�
�
��� ���
�
��
��� ���
��
��
���
�����
��
���
��
��
���
��
��
���
��
��
���
��
��
��
��
��
��
��
��
��
��
��
��
��
��� ��� ���� ����
��
��
��
��
��������
������������������������������
�����������������������
�
��������
��������������������������
� ��������������������������
����������������������������������������������
�
�
�
�
�
�����
�����
������
���
�
���������������
�������������
������������
���������������
��������������
���������
�����
�����
������
���
�
����������������������������������������������
�
�
�
�
���
�
��������������������������
�������������������������������
�����������������������������
�����
�����
������
���
�����������
�
XR2500F Installation Guide
�
�����
�����
������
���
�
�����
�����
������
���
���
�����������������������
�������������������
����������������������
����
������
Digital Monitoring Products
43
Digital Monitoring Products
44
���������
�����
����������
�������������
������������
������������
��������������
��������������
����
������
���������������������
������
�
������
�
���������������������������
�������������
������������
���������
�����
����������
�������������
������������
������������
��������������
��������������
����
������
���������������������
�������
�������
�������������
�������
�
�
�
�
�������
�������������
�
�
������ ���
�
���
��������
������������
��
����
���
������
���
������
���
��
��������
��
������
�
�
�
�
���������
�����
�
�
��
��
�
�
��
�
��
�
�� ��
�
�
��
���
������
���
������
����
����
���
�������
������������
�
�
�
��
�
�� ��
�� ��
��
�� ��
��
��
��
�� ��� �� ��� ��� ���� ����
���
�����
��
���������������������������������
�������������
��������
������������
��������������������
������
����������������������������������
������������������������������������
������������������������
����������������������������������
�����������������������������������
��������������������������������������
������������������������������
��
�����������������
�� ��
�
���
�����������
��
��
��
�
�� ��� �� �� ��� ��
��
�������� ��� ��������
�������������������
�
�
�������
������������������
�����
�������������������������������������������������
��������������������������������������������������
�����������������������������������������������
������������������������������������������������
���������������������������
�� �� �� �� ���� ��� ��� ��� ��� ��� ��� ��� �� ��� ��
��������
�����
��
����������
���������������������������������������������
�����������������������������������������������
���������������������������������������
�������
� ��������������������
���� ����
���������������������������
�������������
������������
WIRING DIAGRAMS
40.6 Multiple Notification Circuits with Strobes and Bells
XR2500F Installation Guide
WIRING DIAGRAMS
��������
�������������������
�����
��
������
��
���
����������
�����
����������
���������
��
�����������������
�����������������������������������
�����������������������������������
���
���
������
�
�
�
���
��
���
��������
�����
��
��
�� �� �� �� ���� ��� ��� ��� ��� ��� ��� ��� �� ��� ��
������������������
������������������
�
�
�
�
�
�
�
�
�
��
��
�� ��
��
���
���
�����
�� ��� �� �� ��� ��
�� ��
��
�� ��
��
�� ��� �� ��� ��� ��������
�� ��
��
��
��
��
��
��
����������������������
�
���������
�������
�������
���
���
����
������
��������
���������������������������������
40.7 Rothenbuhler 5110 High Security Bell Wiring
�
�����������������
�������
�������������
������������
���������������
�������
����������
���
���������������
�������
�������������
XR2500F Installation Guide
Digital Monitoring Products
45
WIRING DIAGRAMS
40.8 LX-Bus™ Module Connection
�����������������������������������������������������������
��������������������������������������������������������
�������������������������������������������������������
�����������������
��������������
����������������������
�������������������
����������
��������������������
������������
���������������������
�����������
������
����������������
����������������
�����������������
�������������
� �
�����������
������������
�����������
������������
�����������
����������
�������������
�������
������������
��������������
��������������
������������������������
�������������������������
���������������������������
�����������������������������
�����������������������
��������������������
����������������������
�
�
�
�
����������
����������
�����������
�������
������������
�������
����
���������������
����
����
������������������������
��������
���
������
����������������������������
�����
�����
�
�
�
�
�
�����������������
����������������
����
��������������
��������������������
�������
�
����������������������������
����������������
�������
�
�
�������
���������������
�������������������
�
�������
����������������
��������
���������������
������
�������������
�����������������
����������������
������������
����������������������������
����������������
������������������
������������
�������
�������������
Digital Monitoring Products
46
XR2500F Installation Guide
XR2500F Installation Guide
��
�
�
�
���
���
���
������
���
��
��
������
��
��
�
�
�
�
�
�
�
�
�
��
��
�� ��
��
�� ��
���
���
��
�� ��
��
���
�����
��
��
��
��
��
��
������
�������
��������
���
���
���
�� �
��
�
�
�
�
�������
�
���������
���������
���������
��������
���������
������������
���������������������
�������������������������
���������������������������������
����
����������
������
������
���
������
���
�����������������������������������������������������������
�����������������������������������������������������������������
����������������������������������������������
�� ��
�� ��� �� �� ��� ��
��
���
����������
�����
����������
���������
�� ��� �� ��� ��� ��������
��������
�������������������
�����
�����������������
����������������������������
������������������������
���������������������
�� �� �� �� ���� ��� ��� ��� ��� ��� ��� ��� �� ��� ��
��������
�����
��
����
WIRING DIAGRAMS
40.9 Model 860 Relay Module Connection
Digital Monitoring Products
47
OPERATING INSTRUCTIONS
MODEL XR2500F PANELS
NORMAL STANDBY CONDITION
When the system is in the normal standby condition, the keypad shows either the time of day or a blank display.
ALARM CONDITION
When the system is in an alarm condition, the keypad display shows the violated zone name(s) followed by an
alarm display.
ALARM SILENCE
To silence the alarm while the bell or siren is sounding, enter your code number and press the COMMAND key.
This silences the alarm but does not cancel any alarm reports to the central station.
RESETTING DETECTORS
To reset a smoke or other detector, enter the User Menu by pressing the COMMAND key until MENU? NO YES
appears in the display. Press the top row key under YES. The display shows ENTER CODE: -. Enter your code
number and press COMMAND. The keypad display now shows ALARM SILENCE? if your code allows. Press the
COMMAND key until SENSOR RESET? appears in the display. Press any top row key.
TROUBLE CONDITION
When a device is in a trouble condition, the keypad tones and displays the zone or device name followed by
TRBL. Press any top row key to silence.
SYSTEM TESTING
You should test the security system periodically to ensure proper operation. You can do this through a function
in the User Menu. After entering the User Menu, press the COMMAND key until SYSTEM TEST? displays. Press the
left most top row Select key. The system bell, battery, and communication to the central station receiver system
is then tested.
ALARM SERVICE
If service is required for this system, please contact:
Company _____________________________________________
Address ______________________________________________
Telephone ____________________________________________
Listings and Approvals
Underwriters Laboratories (UL) Listed
UL 294
Access Control System Units
UL 365
Police Connected Burglar
UL 609
Local Burglar
UL 1023 Household Burglar
UL 1076 Proprietary Burglar
UL 1610 Central Station Burglar
UL 1635 Digital Burglar
UL 985
Household Fire Warning
UL 864
Fire Protective Signaling
California State Fire Marshal (CSFM)
New York City (MEA)
FCC Part 15
FCC Part 68 Registration ID CCKAL00BXR500
800-641-4282
INTRUSION • FIRE • ACCESS • NETWORKS
www.dmp.com
2500 North Partnership Boulevard
Made in the USA
Springfield, Missouri 65803-8877
LT-0759 (10/05) © 2005 Digital Monitoring Products, Inc.
Mounting Instructions
Attach the above operating instructions
to the front, or framed and located
adjacent to, the panel or a Security
Command keypad with an alphanumeric
display.