MGE UPS SYSTEMS
T H E
U N I N T E R R U P T I B L E
P O W E R
P R O V I D E R
140, Avenue Jean Kuntzmann
ZIRST - Montbonnot St Martin
38334 - Saint Ismier Cedex - France
www.mgeups.com
34003905EN/AA
THE UNINTERRUPTIBLE POWER PROVIDER
Installation manual
(66102)
Network
Management
Card Minislot
2006 Edition
www.mgeups.com
INTRODUCTION
OVERVIEW
The Network Management Card (66102) is recommended for central
UPSs protecting entire networks or for UPS units backing up critical
loads.
With the card installed, the UPS has its own IP address and uses the
local computer capabilities to:
◗ supply web pages (http or https (SSL)) with information on status
conditions and measurements/settings/alarms,
◗ integrate an SNMP-based NMS such as HP OpenView, IBM Tivoli
Netview and Computer Associates Unicenter,
◗ communicate with shutdown modules installed on the protected
servers (Network Shutdown Module),
◗ send e-mail and SMS messages,
◗ control the ON/OFF function of the UPS and the outlets,
◗ monitor the Environment Sensor (optional, cat. no. 66846).
MAC address
000623001C07
ETHERNET 10/100BT port
Service port (Settings/Sensor)
UNPACKING AND CHECKS
ETH
ERN
100M
ET
Settin
gs/S
r
Green LED: communication
with the UPS
10M
UPS
data
◗ One Network Management Card (66102),
◗ One serial cable for configuration (34003918),
◗ One installation manual (34003905).
Orange LED: RS232 activity
enso
RS23
2
6610
2
Catalogue number
Orange LED: 10/100M
Green LED: connection +
activity
ETHE
RNET
Settin
gs/Se
nsor
INDICATIONS
100M
10M
UPS
data
RS2
32
6610
2
ETHERNET port
MGE UPS SYSTEMS
www.mgeups.com
Network
Management
Card Minislot
2006 Edition
(66102)
ETH
ERN
ET
LED
ACT
Colour
Green
Installation manual
Setting
s/Sens
or
Status
◗ Card not connected to network
◗ Card connected to network, but no
◗ Flashing
◗ Port is sending/receiving
◗ OFF
◗ ON
◗ Port operating at 10 Mbits/s
◗ Port operating at 100 Mbits/s
100M
10M
On =
Blink Link
= Act
UPS
data
RS232
66102
MGE
THE UNINTERRUPTIBLE POWER PROVIDER
UPS SYSTEMS
100M
CHECK ON UPS VERSION
Orange
Description
◗ OFF
◗ ON
activity
Service port (Settings/Sensor)
LED
Important. Before installing the card, check that the
UPS technical level (NT) is at least equal to that
indicated in the table below.
UPS
Data
UPS
RS232
Colour
Green
Status
◗ OFF
◗ ON
◗ Flashing
Description
◗ Card starting
◗ Communicating with UPS
◗ Normal operation
Communication with UPS is
operational
Pulsar Extreme C
700/1000/1500
B2
◗ OFF
◗ ON
◗ Configuration menu activated
◗ Normal operation
Pulsar Extreme C
2200/3200
02
◗ Flashing
◗ Communication with Environment
Pulsar Evolution
500/800/1100
06
Pulsar Evolution
1500
05
Pulsar Evolution
2200/3000
05
Pulsar EX RT (US)
700/1000/1500
03
Pulsar EX 2200 RT (US)
2200
09
Pulsar EX 3200 RT (US)
3200
09
Type
Technical level (NT)
Note.
◗ If the technical level of the UPS is lower than that indicated in the
table, contact MGE UPS SYSTEMS.
◗ The Network Management Card (66102) is not compatible with the
Pulsar EX 7/10/15/20/30 and Pulsar ESV+ 8/11/14/22 ranges.
34003905EN/AA
Orange
Configuration menu not activated
Sensor (option)
INSTALLATION
The Network Management Card (66102) can be hot-plugged on all
UPSs from MGE UPS SYSTEMS equipped with a Minislot. It is not
necessary to shutdown the UPS, disconnect the load or restart the
UPS.
◗ Remove the plastic cover of the Minislot.
◗ Note the MAC address of the card before inserting it.
ETH
ERN
ET
Setting
s/Sens
or
ASI
100M
10M
On =
Blink Link
= Act
UPS
data
RS232
66102
Your network is not equipped with a BOOTP/DHCP server
◗ Manual configuration is required.
◗ In the main menu, enter 2 (Network configuration), then again 2
(Modify Network settings).
◗ Follow the instructions and enter the IP parameters.
◗ Wait until "Done" is displayed, indicating that the IP parameters have
been saved.
◗ Return to the main menu and enter 1 (Reset). The card restarts with
the new IP settings (after approx. two minutes).
-----------------------------------------------------------------------------------------1 : Read Network settings
2 : Modify Network settings
3 : Exit
-----------------------------------------------------------------------------------------For each of the following questions, you can press "Return" to select
the value shown in braces, or you can enter a new value.
Should this target obtain IP settings from the network?[N] N
Static IP address [172.17.16.16]? 172.17.21.141
Subnet mask IP address [255.255.0.0]? 255.255.255.0
Gateway address IP address [0.0.0.0]? 172.17.17.1
Done
ETHERNET
◗ Insert and secure the card with the screws.
◗ Connect the ETHERNET cable.
◗ Check the ETHERNET port indications.
◗ Wait until the UPS Data LED flashes regularly (approx. two minutes),
indicating that card start-up has terminated correctly.
Note. Connection detection continues until the card has been
connected to the network. Once connection is made, card start-up
continues.
ACCESS TO SUPERVISION
To check whether the Network Management Card is operational after
installation and configuration, proceed as follows.
◗ Run a browser and enter in the address bar:
http://IP address/ (e.g. http://172.17.21.141/)
◗ The home page is displayed.
IP SETTINGS
Once the card has started, proceed as indicated below.
◗ Connect one end of the cable (34003918) to the Service port.
◗ Connect the other end of the cable to the COM (IOIOI) port of a PC.
◗ Run a terminal emulator such as HyperTerminalTM:
>Bits per second: 9600
Data bits: 8
>Parity: none
Stop bits: 1
>Flow control: none
>"Echo typed characters locally" option: disabled
◗ Type MGEUPS or mgeups, then press the ↵ key.
The main configuration menu is displayed.
----------------------------------------------------------------------------------------MGE UPS SYSTEMS
NETWORK MANAGEMENT CARD
-----------------------------------------------------------------------------------------1 : Reset
2 : Network configuration
3 : Set Login Password to Default
4 : Return to Default Configuration
5 : Exit
-----------------------------------------------------------------------------------------Your network is equipped with a BOOTP/DHCP server
◗ The card is configured by default with this service enabled.
◗ No manual configuration is required.
◗ The IP parameters are automatically collected by the card.
◗ To view the IP parameters, enter 2 (Network configuration), then enter
1 (Read Network settings).
The settings supplied by the server are displayed.
Network configuration :
Mode : DHCP
MAC address : 000623001C07
IP address : 172.17.23.18
Subnet mask : 255.255.248.0
Gateway : 172.17.17.1
◗ Set the time by clicking the Time command.
◗ Continue configuration via the sections in the Settings menu.
USER MANUAL
This manual provides all the information required to install and
configure the Network Management Card.
For more information on the supervision, control and configuration
functions offered by the Network Management Card, see the user
manual on the Solution-Pac 2 CD-ROM or in the Products/Power
Management section of the www.mgeups.com site.
◗ Note the IP address.
◗ To exit this function, enter 3, then 5 (Exit).
34003905EN/AA
SENSOR CONNECTION (option)
The Environment sensor is a Network Management Card option. It is
available from MGE UPS SYSTEMS (cat. no 66846).
The sensor remotely monitors the UPS environment by regularly
measuring the temperature and humidity, and checking the states of
two external contacts. It can also send alarms (e-mail, SNMP trap)
tripped by pre-set thresholds.
Connection is made via the Service port (Settings/Sensor) on the
Network Management Card. The sensor is detected automatically.
Configuration and supervision use a menu that may be accessed
directly from the home page. For more information, see the user
manual of the Network Management Card.
TECHNICAL CHARACTERISTICS
Physical characteristics
Dimensions (W x D x H)
132 x 66 x 42 mm
Weight
70 g
RoHS
100% compatible
Storage
Storage temperature
range
-10°C to 70°C
Ambient conditions
Operating temperature
range
0°C to 40°C
Relative humidity
90% RH max. without condensation
ETHERNET
Card performance
ETHE
RNET
Setti
ngs/S
enso
r
100M
10M
On =
Blin Link
k = Act
UPS
data
RS2
32
6610
2
Supply voltage
5V ±5%
Supply current (all LEDs
ON and Environment
Sensor connected)
300 mA max.
Functions
Web supervision
5 browsers max. (http),
3 browsers max. (https)
Languages
English, French, German, Italian, Spanish
Alarms
E-mail, SNMP TRAP, Web page
Log
400 measurements or events
Server protection
Up to 50 servers protected
Network
Fast ETHERNET, 10/100 Mbits, auto-negotiation
HTTP 1.1, SNMP V1, NTP, TFTP, SMTP,
BOOTP/DHCP
Identification
User name and password
Security
SSL 3.0, TLS 1.0
Browsers
Microsoft Internet Explorer 6.x or higher
NMS
Enterprise Power Manager (EPM)
Management-Pac 2
MIB
MIB II standard - MGE V1.7 MIB
Settings (default values)
IP network
BOOTP/DHCP enabled
IP address: 172.17.16.16
Subnet mask: 255.255.0.0
Gateway: 0.0.0.0
NTP server: pool.ntp.org
Web-page access control
User name: MGEUPS
Password: MGEUPS
Service-port menu access
control
Password: MGEUPS or mgeups
(not modifiable)
Date and time
Synchronise with an NTP server (GMT)
Service port
9600 bits/s, 8 bits, 1 bit stop, no parity
ELECTROMAGNETIC COMPATIBILITY
When correctly installed and used in accordance with manufacturer
instructions, the card complies with the following standards:
◗ ITE (Information Technology Equipment) safety: IEC/EN 60950-1
2002
◗ EMC: EN 61000-6-2 (2002), EN 61000-6-3 (2002), IEC/EN 62040-2 (2002)
In compliance with European directives:
◗ Low voltage: 73/23/EEC and 93/68/EEC.
◗ EMC: 89/336/EEC and 93/68/EEC.
Federal Communication Commission (FCC) statement
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment.
WEB SITE
The information presented in this manual is also available in other
languages in the download section of the MGE UPS SYSTEMS site
(www.mgeups.com).
34003905EN/AA