Philips ADSL 515 Specifications

SNV6520
ADSL Modem Multiservices PSTN Voice
VERSION 1.0
European Regulations
This product has been designed, tested and manufactured according to the European R&TTE Directive 1999/5/EC.
Following this Directive, this product can be brought into service in the following states:
Hereby, Philips Consumer Electronics, BLC P&A CC, declares that this SNA6500 is in compliance with the essential requirements
and other relevant provisions of Directive 1999/5/EC.
B
IRL
P
D
✔
✘
✘
✘
DK ✘ E
I ✘ L
SU ✘ S
CH ✘
✘ GR ✘ F ✘
✘ NL ✘ A ✘
✘ UK ✘ N ✘
August 2005
Disposal of your old product
Your product is designed and manufactured with high quality materials and components, which can be recycled
and reused.
When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the
European Directive 2002/96/EC
Please inform yourself about the local separate collection system for electrical and electronic products.
Please act according to your local rules and do not dispose of your old products with your normal household
waste. The correct disposal of your old product will help prevent potential negative consequences for the
environment and human health.
Table of Contents
4
Introduction
4
4
4
4
4
4
About the ADSL Modem Multiservices PSTN Voice
Telephony over IP
Important information
Safety Precautions
Environmental information
Disclaimer
5
Installation
5
5
5
7
8
8
8
9
Package Contents
System Requirements
Hardware Description
LEDs
Hardware Installation
ISP Settings
Connect the System
Phone Line Configuration
11
11
13
14
15
16
18
18
19
20
21
23
24
24
25
27
30
31
38
41
45
53
54
56
63
64
66
EN
Configuring The Client PC
TCP/IP Configuration
Disable HTTP Proxy
Configuring Your Computer in Windows XP DHCP IP Configuration
Obtain IP Settings from Your ADSL Modem Multiservices PSTN Voice
Disable HTTP Proxy
Configuring The ADSL Modem Multiservices PSTN Voice
Navigating the Web Browser Interface
Setup Wizard
Configure your Telephone settings
ADSL
Status
Advanced Setup
Making Configuration Changes
System Settings
WAN
LAN
Wireless
NAT
Route
Firewall
SNMP
ADSL
Telephony
Troubleshooting
Glossary
Specifications
3
EN
Introduction
SNV6520
Congratulations on your purchase of the ADSL Modem Multiservices PSTN Voice.
We are proud to provide you with a powerful yet simple communication device for
connecting your local area network (LAN) to the Internet. For those who want to
surf the Internet in the most secure way, this router provides a convenient and
powerful solution. The ADSL Modem Multiservices PSTN Voice also enables service
providers to provide their residential and small office home office (SOHO) customers
with high-quality Telephony service using traditional analog telephones and fax
machines.
About the ADSL Modem Multiservices PSTN Voice
The ADSL Modem Multiservices PSTN Voice provides Internet access to multiple
users by sharing a single-user account. It is a cost-efficient means for service
providers to migrate their customers’ traditional analog telephones and fax machines
onto IP-based networks. This new technology provides many secure and costeffective functions. It is simple to configure and can be up and running in minutes.
Telephony over IP
Using Telephony over IP, instead of making calls over the regular telephone network,
calls are made over computer (IP) networks, either through your Internet Service
Provider’s connection or through your local network.
The basic steps involved in Telephony include the conversion of an analog voice signal
to digital, the encoding and then compression of the signal into Internet Protocol (IP)
packets. The ADSL Modem Multiservices PSTN Voice is equipped with a digital signal
processor (DSP), which segments the voice signal into frames and stores them in
voice packets. Using the industry standard codecs, G.711, G.723.3 and G.729, these
packets are encoded. These IP packets are then transmitted in accordance with
International Telecommunications Union specification SIP over the Internet to their
destination where the process is reversed.
Important information
•
•
•
Please install and connect the product in the order as described in the chapter
‘Before You Start Guide’ only.This assures best installation results with the least
technical hassles.
Please read this guide carefully before using the ADSL Wireless Base Station; and
keep it for future reference.
During set-up and installation, it may be helpful to have the instructions for your
PC and other network components at hand.
Safety Precautions
•
•
•
•
•
Do not expose the product to excessive moisture, rain, sand or heat sources.
The product should not be exposed to dripping or splashing. No object filled with
liquids, such as vases, should be placed on the product.
Keep the product away from domestic heating equipment and direct sunlight.
Allow a sufficient amount of free space all around the product for adequate
ventilation.
Do not open this product. Contact your retailer if you experience technical
difficulties.
Environmental information
All redundant packing material has been omitted. We have done our utmost to make
the packaging easily separable into three mono materials: cardboard (box),
polystyrene foam (buffer) and polyethylene (bags, protective foam sheet).Your set
consists of materials that can be recycled if disassembled by a specialised company.
Please observe the local regulations regarding the disposal of packing materials,
exhausted batteries and old equipment.
Disclaimer
This product is provided by ‘Philips’ ‘as is'' and without any express or implied
warranty of any kind of warranties, including, but not limited to, the implied
warranties of merchantability and fitness for a particular purpose are disclaimed.
In no event shall Philips be liable for any direct, indirect, incidental, special, exemplary,
or consequential damages (including, but not limited to, procurement of substitute
goods or services; loss of information, data, or profits; or business interruption)
howsoever caused and on any theory of liability, whether in contract, strict liability,
or tort (including negligence or otherwise) arising in any way out of the use of
inability to use this product, even if advised of the possibility of such damages.
Philips further does not warrant the accuracy or completeness of the information, text,
graphics, illustrative examples links or other items can be deviated of the product.
4
Installation
EN
Before installing the ADSL Modem Multiservices PSTN Voice, verify that you have all
the items listed under ‘Package Contents.’ If any of the items are missing or damaged,
contact your local distributor. Also be sure that you have all the necessary cabling
before installing the ADSL Modem Multiservices PSTN Voice. After installing the
ADSL Modem Multiservices PSTN Voice, refer to ‘Configuring the ADSL Modem
Multiservices PSTN Voice’.
Package Contents
After unpacking the ADSL Modem Multiservices PSTN Voice, check the contents of
the box to be sure you have received the following components:
• ADSL Modem Multiservices PSTN Voice
• Power adapter
• One CAT-5 Ethernet cable
• Telephone patch cable
• One driver and documentation CD
Immediately inform your dealer in the event of any incorrect, missing, or damaged
parts. If possible, please retain the carton and original packing materials in case there
is a need to return the product.
System Requirements
You must meet the following minimum requirements:
• Internet access from your Internet Service Provider (ISP) using an ADSL modem.
• A PC using a dynamic IP address assigned via DHCP, as well as a gateway server
address and DNS server address from your service provider.
• A computer equipped with a 10 Mbps, 100 Mbps, or 10/100 Mbps Fast Ethernet
card.
• TCP/IP network protocols installed on each PC that will access the Internet.
• A Java-enabled web browser, such as Microsoft Internet Explorer 5.0 or above
installed on one PC at your site for configuring the ADSL Modem Multiservices
PSTN Voice.
Hardware Description
The ADSL Modem Multiservices PSTN Voice contains an integrated ADSL modem
and connects to the Internet or to a remote site using its RJ-11 port. It can be
connected directly to your PC or to a local area network using the Fast Ethernet
LAN ports. There is also one USB 1.1 connection to connect to your printer or a
secondary storage device.
Access speed to the Internet depends on your service type. Full-rate ADSL provides
up to 8 Mbps downstream and 640 kbps upstream. G.lite (or splitterless) ADSL
provides up to 1.5 Mbps downstream and 512 kbps upstream. However, you should
note that the actual rate provided by specific service providers might vary
dramatically from these upper limits.
5
EN
The ADSL Modem Multiservices PSTN Voice comes with two FXS ports to connect
with a phone or fax, turning your regular phone into an IP phone. Through your
telephone or FAX, your can dial out through the gateway to another Telephony
gateway or IP Phone.
Data passing between devices connected to your local area network can run at up to
100 Mbps over the four Fast Ethernet ports.
The ADSL Modem Multiservices PSTN Voice connections are described in the
following figure and table.
Item
ADSL Port
LAN Ports
Power Switch
Power Inlet
Reset Button
USB Port
FXS Ports
6
Description
ADSL port (RJ-11). Connect your ADSL line to this port.
Fast Ethernet ports (RJ-45). Connect devices on your local area
network to these ports (i.e., a PC, hub, or switch).
Push to power on the device.
Connect the included power adapter to this inlet.
Warning: Using the wrong type of power adapter may cause damage.
Use this button to reset the power and restore the default factory
settings. To reset without losing configuration settings, see ‘Reset’
on page 61.
Connect to print server.
RJ-11 port. Connect to standard analog telephone set or fax
Machine.
LEDs
The ADSL Modem Multiservices PSTN Voice includes an LED display for system
power and port indications that simplifies installation and network troubleshooting.
The power and port LED indicators are explained by the following figure and table.
1
2
3
4
Item
1. Phone2, 1
Status
ON
Blinking Green
Off
2. TEL
3. USB
4. LAN 1, 2, 3, 4
5. WL
6. On Line
7. ADSL
8. PWR
Solid Green
Off
Solid Green
Off
Green
Blinking green
Off
On
Blinking
Green
Blinking
Blinking green
Green
Green
EN
8
7
6
5
Description
When Phone is OFF-Hook talking on a Call
On an Incoming Telephone Call when it rings
the phone or in call waiting stage
When modem is having no communication on
ADSL or Internet Telephony
When Telephone registration is successful
When there is no connection
When USB device is up and connected
When there is no connection
When connected to each port on the LAN
When there is activity on each port
Wireless disabled
Wireless enabled
Wireless traffic
When Link is Up
When sending and receiving data
When initializing
When initialized
When power is on
7
EN
Hardware Installation
ADSL Connection
Connect your ADSL line to this port.
Fast Ethernet Connection
Connect a PC to one of the RJ-45 ports on the ADSL Modem Multiservices PSTN
Voice with the provided network cable. When inserting an RJ-45 plug, be sure the tab
on the plug clicks into position to ensure that it is properly seated.
The LAN ports are dual-speed RJ-45 ports. They support auto-negotiation,
so the optimum communication mode (half or full duplex) and data rate
(10 Mbps or 100 Mbps) are selected automatically.
USB Connection
Using the USB port, connect to a secondary storage device or printer.
This port allows you to, for example, share your USB printer over the network
without needing to leave a host PC switched on.
FXS Connection
Connect a standard analog telephone set or fax machine to either of the FXS ports
on the rear panel. The FXS ports are like your local phone service provider in that
they can generate and provide a ring signal.
Note: When you have connected a device to the FXS port as you will hear a dial tone
provided by the FXS port once the handset is off-hook.
ISP Settings
Please collect the following information from your ISP before setting up the ADSL
Modem Multiservices PSTN Voice:
• ISP account user name and password
• Protocol, encapsulation and VPI/VCI circuit numbers
• DNS server address
• IP address, subnet mask and default gateway (for fixed IP users only)
Connect the System
The ADSL Modem Multiservices PSTN Voice can be positioned at any convenient
location in your office or home. No special wiring or cooling requirements are
needed. You should, however, comply with the following guidelines:
• Keep the ADSL Modem Multiservices PSTN Voice away from any heating devices.
• Do not place the ADSL Modem Multiservices PSTN Voice in a dusty or wet
environment.
You should also remember to turn off the power, remove the power cord from the
outlet, and keep your hands dry when you install the ADSL Modem Multiservices
PSTN Voice.
Connect the ADSL Line
Run standard telephone cable from the wall jack providing ADSL service to the RJ-11
(‘ADSL’) port on your ADSL Modem Multiservices PSTN Voice. When inserting an
ADSL RJ-11 plug, be sure the tab on the plug clicks into position to ensure that it is
properly seated. If you are using splitterless ADSL service, be sure you add low-pass
filters between the ADSL wall jack and your telephones. (These filters pass voice
signals through but filter data signals out.)
8
Phone Line Configuration
Installing a Full-Rate Connection
EN
If you are using a full-rate (G.dmt) connection, your service provider will attach the
outside ADSL line to a data/voice splitter. In this case you can connect your phones
and computer directly to the splitter as shown below:
Installing a Splitterless Connection
If you are using a splitterless (G.lite) connection, then your service provider will
attach the outside ADSL line directly to your phone system. In this case you can
connect your phones and computer directly to the incoming ADSL line, but you will
have to add low-pass filters to your phones as shown below:
9
Attach to Your Network Using Ethernet Cabling
EN
The LAN ports on the ADSL Modem Multiservices PSTN Voice auto-negotiates the
connection speed to 10 Mbps Ethernet or 100 Mbps Fast Ethernet, as well as the
transmission mode to half duplex or full duplex.
Use twisted-pair cabling to connect any of the LAN ports on the ADSL Modem
Multiservices PSTN Voice to an Ethernet adapter on your PC. Otherwise, cascade
the LAN port on the ADSL Modem Multiservices PSTN Voice to an Ethernet hub or
switch, and then connect your PC or other network equipment to the hub or switch.
When inserting an RJ-45 connector, be sure the tab on the connector clicks into
position to ensure that it is properly seated.
Warning: Do not plug a phone jack connector into an RJ-45 port. This may damage the
ADSL Modem Multiservices PSTN Voice. Instead, use only twisted-pair cables with
RJ-45 connectors that conform with FCC standards.
Notes:
– Use 100-ohm shielded or unshielded twisted-pair cable with RJ-45 connectors for all
Ethernet ports. Use Category 3, 4, or 5 for connections that operate at 10 Mbps,
and Category 5 for connections that operate at 100 Mbps.
– Make sure each twisted-pair cable length does not exceed 100 meters (328 feet).
Connect the Power Adapter
Plug the power adapter into the power socket on the side panel of the ADSL Modem
Multiservices PSTN Voice, and the other end into a power outlet.
Check the power indicator on the front panel is lit.
If the power indicator is not lit, refer to the chapter ‘Troubleshooting’.
In case of a power input failure, the ADSL Modem Multiservices PSTN Voice will
automatically restart and begin to operate once the input power is restored.
If the ADSL Modem Multiservices PSTN Voice is properly configured, it will take
about 30 seconds to establish a connection with the ADSL service provider after
powering up. During this time the Sync indicator will flash. After the ADSL
connection has been established, the ADSL Sync LED will stay on.
10
Configuring The Client PC
EN
After completing hardware setup by connecting all your network devices, you need
to configure your computer to connect to the ADSL Modem Multiservices PSTN
Voice. First determine how your ISP issues your IP address. Many ISPs issue these
numbers automatically using Dynamic Host Configuration Protocol (DHCP). Other
ISPs provide a static IP address and associated numbers, which you must enter
manually. How your ISP assigns your IP address determines how you need to
configure your computer.
Depending on your operating system see:
‘Configuring Your Computer in Windows 2000’ on page 11,
‘Configuring Your Computer in Windows XP’ on page 14, or
‘Configuring Your Macintosh Computer’ on page 16.
TCP/IP Configuration
To access the Internet through the ADSL Modem Multiservices PSTN Voice, you
must configure the network settings of the computers on your LAN to use the same
IP subnet as the ADSL Modem Multiservices PSTN Voice. The default network
settings for the ADSL Router are:
IP Address: 192.168.2.1
Subnet Mask: 255.255.255.0
Note: These settings can be changed to fit your network requirements, but you must first
configure at least one computer to access the ADSL Modem Multiservices PSTN
Voice’s web configuration interface in order to make the required changes. (See
‘Configuring the ADSL Modem Multiservices PSTN Voice’ for instruction on
configuring the ADSL Modem Multiservices PSTN Voice.)
Configuring Your Computer in Windows 2000
DHCP IP Configuration
1. On the Windows desktop, click Start/Settings/ Network and Dial-Up
Connections.
2. Click the icon that corresponds to the connection to your ADSL Modem
Multiservices PSTN Voice.
3. The connection status screen will open. Click Properties.
11
EN
1. Double-click Internet Protocol (TCP/IP).
2. If ‘Obtain an IP address automatically’ and ‘Obtain DNS server address
automatically’ are already selected, your computer is already configured for
DHCP. If not, select these options. Click Cancel to close each window.
Obtain IP Settings From Your ADSL Modem Multiservices
PSTN Voice
Now that you have configured your computer to connect to your ADSL Modem
Multiservices PSTN Voice, it needs to obtain new network settings. By releasing old
DHCP IP settings and renewing them with settings from your ADSL Modem
Multiservices PSTN Voice, you can verify that you have configured your computer
correctly.
1. On the Windows desktop, click Start/Programs/ Accessories/Command Prompt.
2. In the Command Prompt window, type ‘IPCONFIG /RELEASE’ and press the
ENTER key.
12
1. Type ‘IPCONFIG /RENEW’ and press the ENTER key. Verify that your IP
Address is now 192.168.2.xxx, your Subnet Mask is 255.255.255.0 and your
Default Gateway is 192.168.2.254. These values confirm that your ADSL Modem
Multiservices PSTN Voice is functioning.
2. Type ‘EXIT’ and press the ENTER key to close the Command Prompt window.
EN
Manual IP Configuration
1. Follow steps 1-4 in ‘DHCP IP Configuration’ on page 11.
2. Select ‘Use the following IP address automatically.’ Enter an IP address based on
the default network 192.168.2.x (where x is between 2 and 254), use
255.255.255.0 for the subnet mask and the IP address of the ADSL Modem
Multiservices PSTN Voice (default: 192.168.2.1) for the Default gateway field.
3. Select ‘Use the following DNS server addresses.’
4. Enter the IP address for the ADSL Modem Multiservices PSTN Voice in the
Preferred DNS server field. This automatically relays DNS requests to the DNS
server(s) provided by your ISP. Otherwise, add a specific DNS server into the
Alternate DNS Server field and click OK to close the dialog boxes.
5. Record the configured information in the following table.
TCP/IP Configuration Setting
IP Address ____.____.____.____
Subnet Mask ____.____.____.____
Preferred DNS Server ____.____.____.____
Alternate DNS Server ____.____.____.____
Default Gateway ____.____.____.____
Disable HTTP Proxy
You need to verify that the ‘HTTP Proxy’ feature of your web browser is disabled.
This is so that your browser can view the ADSL Modem Multiservices PSTN Voice’s
HTML configuration pages.
Your computer is now configured to connect to the ADSL Modem Multiservices
PSTN Voice.
13
Configuring Your Computer in Windows XP DHCP IP
Configuration
EN
Is deze goed?
14
•
On the Windows desktop, click Start/Control Panel.
•
In the Control Panel window, click Network and Internet Connections.
•
The Network Connections window will open. Locate and double-click the Local
Area Connection icon for the Ethernet adapter that is connected to the ADSL
Modem Multiservices PSTN Voice.
•
In the connection status screen, click Properties.
•
Double-click Internet Protocol (TCP/IP).
•
If ‘Obtain an IP address automatically’ and ‘Obtain DNS server address
automatically’ are already selected, your computer is already configured for
DHCP. Click Cancel to close each window.
EN
Obtain IP Settings from Your ADSL Modem Multiservices
PSTN Voice
Now that you have configured your computer to connect to your ADSL Modem
Multiservices PSTN Voice, it needs to obtain new network settings. By releasing old
DHCP IP settings and renewing them with settings from your ADSL Modem
Multiservices PSTN Voice, you can verify that you have configured your computer
correctly.
1. On the Windows desktop, click Start/Programs/Accessories/ Command Prompt.
2. In the Command Prompt window, type ‘IPCONFIG /RELEASE’ and press the
ENTER key.
3. Type ‘IPCONFIG /RENEW’ and press the ENTER key. Verify that your IP
Address is now 192.168.2.xxx, your Subnet Mask is 255.255.255.0 and your
Default Gateway is 192.168.2.1. These values confirm that your ADSL Modem
Multiservices PSTN Voice is functioning.
15
Type ‘EXIT’ and press the ENTER key to close the Command Prompt window.
EN
Your computer is now configured to connect to the ADSL Modem Multiservices
PSTN Voice.
Manual IP Configuration
1. Follow steps 1-5 in ‘DHCP IP Configuration’ on page 14.
2. Select ‘Use the following IP Address.’
3. Enter an IP address based on the default network 192.168.2.x (where x is
between 2 and 254), use 255.255.255.0 for the subnet mask. and the IP address of
the ADSL Modem Multiservices PSTN Voice (default: 192.168.2.1) for the Default
gateway field.
4. Select ‘Use the following DNS server addresses.’
5. Enter the IP address for the ADSL Modem Multiservices PSTN Voice in the
Preferred DNS server field. This automatically relays DNS requests to the DNS
server(s) provided by your ISP. Otherwise, add a specific DNS server into the
Alternate DNS Server field and click OK to close the dialog boxes.
6. Record the configured information in the following table.
TCP/IP Configuration Setting
IP Address ____.____.____.____
Subnet Mask ____.____.____.____
Preferred DNS Server ____.____.____.____
Alternate DNS Server ____.____.____.____
Default Gateway ____.____.____.____
Disable HTTP Proxy
You need to verify that the ‘HTTP Proxy’ feature of your web browser is disabled.
This is so that your browser can view the ADSL Modem Multiservices PSTN Voice’s
HTML configuration pages.
Your computer is now configured to connect to the ADSL Modem Multiservices
PSTN Voice.
Configuring Your Macintosh Computer
You may find that the instructions here do not exactly match your operating system.
This is because these steps and screen shots were created using Mac OS 10.2. Mac
OS 7.x and above are similar, but may not be identical to Mac OS 10.2.
Follow these instructions:
• Pull down the Apple Menu. Click System Preferences.
•
16
Double-click the Network icon in the Systems Preferences window.
•
If ‘Using DHCP Server’ is already selected in the Configure field, your computer is
already configured for DHCP. If not, select this Option.
•
Your new settings are shown in the TCP/IP tab. Verify that your IP Address is
now 192.168.2.xxx, your Subnet Mask is 255.255.255.0 and your Default Gateway
is 192.168.2.1. These values confirm that your ADSL Modem Multiservices PSTN
Voice is functioning.
Close the Network window.
•
EN
Now your computer is configured to connect to the ADSL Modem Multiservices
PSTN Voice.
Disable HTTP Proxy
You need to verify that the ‘HTTP Proxy’ feature of your web browser is disabled.
This is so that your browser can view the ADSL Modem Multiservices PSTN Voice’s
HTML configuration pages. The following steps are for Internet Explorer.
Internet Explorer
•
Open Internet Explorer and click the Stop button. Click Explorer/Preferences.
•
In the Internet Explorer Preferences window, under Network, select Proxies.
•
Uncheck all check boxes and click OK.
17
Configuring The ADSL Modem
Multiservices PSTN Voice
After you have configured TCP/IP on a client computer, use a web browser to
configure the ADSL Modem Multiservices PSTN Voice. The ADSL Modem
Multiservices PSTN Voice can be configured by any Java-supported browser such as
Internet Explorer 4.0 or above. Using the web management interface, you may
configure the ADSL Modem Multiservices PSTN Voice and view statistics to monitor
network activity.
To access the ADSL Modem Multiservices PSTN Voice’s management interface, enter
the IP address of the ADSL Modem Multiservices PSTN Voice in your web browser:
http://192.168.2.1
(The ADSL Modem Multiservices PSTN Voice automatically switches to Port 88 for
management access.) Then click LOGIN. (By default there is no password.)
Navigating the Web Browser Interface
The ADSL Modem Multiservices PSTN Voice’s management interface consists of a
Setup Wizard and an Advanced Setup section.
Setup Wizard: Use the Setup Wizard if you want to quickly set up the ADSL
Modem Multiservices PSTN Voice. Go to ‘Setup Wizard’.
Advanced Setup: Advanced Setup supports more advanced functions like hacker
attack detection, IP and MAC address filtering, virtual server
setup, virtual DMZ host, as well as other functions. Go to
‘Advanced Setup’.
Making Configuration Changes
Configurable parameters have a dialog box or a drop-down list. Once a configuration
change has been made on a page, be sure to click the ‘SAVE SETTINGS’ or ‘NEXT’
button at the bottom of the page to enable the new setting.
Note: To ensure proper screen refresh after a command entry, be sure that Internet
Explorer 5.0 is configured as follows: Under the menu Tools/Internet
Options/General/Temporary Internet Files/Settings, the setting for ‘Check for newer
versions of stored pages’ should be ‘Every visit to the page.’
18
Setup Wizard
Quickstart
EN
The first item in the Setup Wizard is Quickstart. The ADSL Wireless Base Station
displays the Quickstart Web page.
Enter the Username and Password supplied by your Internet Service Provider.
• Enable Wireless
The wireless function is enabled by default. If you want to disable the wireless
function of the ADSL Wireless Base Station, you can uncheck the ‘Enable Wireless’
checkbox.
• Enable Broadcast
The ADSL Wireless Base Station broadcasts its Wireless ID by default. This means
that the SSID will appear as an available network when scanned for by wirelessenabled devices.
If you uncheck this checkbox, you must manually type in the identical SSID in your
wireless devices or clients in order to connect to the ADSL Wireless Base Station
network.
• Wireless ID (SSID)
The Wireless ID is preset to ‘WiFi_xx?’. The ‘xx’ corresponds with an unique
number in your ADSL Wireless Base Station. You can either leave it as is, or change
it. On client PCs’ software, this might also be called the Network Name. The
Wireless ID is used to identify this particular wireless network. Please refer to the
manual of your wireless client on how to connect to the ADSL Wireless Base Station.
• Telephone Service
The telephone service is disabled by default. If you want to enable the Telephone
function of the ADSL Wireless Base Station you can check the enable box to turn on
the ‘Telephone Service’ function.
• Click the ‘Save Settings/Next’ button.
Once you leave your Telephone Service disabled please click on ‘Save Settings’ and
continue. You can now surf to your favorite websites by typing an URL in your
browser’s location box or by selecting one of your favorite Internet bookmarks. If
you enabled the Telephone Service please click on ‘Next’ and continue with Step
‘Phone Number Selection’.
19
Configure your Telephone settings
EN
1. Phone Number Selection
Please indicate which number you want to use and click ‘Next’. For this example
scenario with ‘3 Phone numbers’ has been choosen to explain the generic
configuration.
2. Phone Number Settings
Enter the telephone number, Login and Password supplied by your Internet Service
provider. Repeat this for each available Phone Number. The ADSL Modem
Multiservices PSTN Voice can append telephone numbers to outgoing calls.
Select the number you want to use for each port. Click ‘Save Settings’.
The connection status page will appear.
20
EN
3. Click the ‘Ok’ button.
Congratulations! Your Telephone configuration is complete. Click ‘OK’ to continue.
In case of error or disfunction, use the Back Button of the browser, and repeat the
process.
ADSL
ADSL (Asymmetric Digital Subscriber Line) is designed to deliver more bandwidth
downstream (from the central office to the customer site) than upstream. This
section is used to configure the ADSL operation type and shows the ADSL status.
21
EN
This page is designed for the engineer to test the ADSL loop condition.
Therefore, it is advised that users should not change the settings here at all.
22
Status
The Status screen displays information on connection line status, data rate, operation
data and defect indication, and statistics.
EN
The following items are included on the ADSL status page:
Parameter
Status
• Line Status
• Link Type
Data Rate
• Upstream
• Downstream
Operation Data/
Defect Indication
• Noise Margin
• Attenuation
• Fast Path FEC
Correction
• Interleaved Path FEC
Fast Path CRC Error
Interleaved Path CRC
Error
Loss of Signal Defect
Fast Path HEC Error
Interleaved Path HEC
Statistics
• Received cells
• Transmitted cells
Description
Shows the current status of the ADSL line connection.
Two types of link: Fast path and Interleaved path.
Maximum upstream data rate.
Maximum downstream data rate.
Maximum upstream and downstream noise margin.
Maximum reduction in the strength of the upstream and
downstream signal.
There are two latency paths that may be used: fast and
interleaved. For either path, a forward error correction (FEC)
scheme is employed to ensure higher data integrity. For
maximum noise immunity, an interleaver may be used to
supplement FEC.
An interleaver is basically a buffer used to introduce a delay,
allowing for Correction additional error correction
techniques to handle noise. Interleaving slows the data flow
and may not be optimal for real-time signals such as video
transmission.
The number of Fast Path Cyclic Redundancy Check errors.
The number of Interleaved Path Cyclic Redundancy Check
errors.
Momentary signal discontinuities.
Fast Path Header Error Concealment errors.
Error Interleaved Path Header Error Concealment errors.
(Superframes represent the highest level of data presentation.
Each superframe contains regular ADSL frames, one of which
is used to provide superframe synchronization, identifying the
start of a superframe. Some of the remaining frames are also
used for special functions.)
Number of cells received.
Number of cells transmitted.
23
Advanced Setup
EN
Clicking the Home icon returns you to the home page. The Main Menu links are used
to navigate to other menus that display configuration parameters and statistics.
The ADSL Modem Multiservices PSTN Voice’s advanced management interface
contains 14 main menu items as described in the following table.
Menu: Description
• System: Sets the local time zone, the password for administrator access, the IP
address of a PC that will be allowed to manage the ADSL Modem
Multiservices PSTN Voice remotely, and the IP address of a Domain
Name Server.
• WAN: Specifies the Internet connection settings.
• LAN: Sets the TCP/IP configuration for the ADSL Modem Multiservices PSTN
Voice LAN interface and DHCP clients.
• Wireless: Configures the radio frequency, SSID, and security for wireless
communications.
• NAT: Shares a single ISP account with multiple users, sets up virtual servers.
• Route: Sets routing parameters and displays the current routing table.
Menu: Description
• Firewall: Configures a variety of security and specialized functions including:
Access Control, URL blocking, Internet access control scheduling,
Intruder detection, and DMZ.
• SNMP: Community string and trap server setting.
• ADSL: Sets the ADSL operation type and shows the ADSL status.
• Telephony: Configures Telephony settings for the ADSL Modem Multiservices
PSTN Voice.
• QoS: Allows you to optimize voice quality by prioritizing voice over data traffic.
• File: Allows you to enable or disable file server functionality. Server
• Tools: Contains options to back up and restore the current configuration,
restore all configuration settings to the factory defaults, update system
firmware, or reset the system.
• Status: Provides WAN connection type and status, firmware and hardware
version numbers, system IP settings, as well as DHCP, NAT, and firewall
information.
Displays the number of attached clients, the firmware versions, the
physical MAC address for each media interface, and the hardware version
and serial number.
Shows the security and DHCP client log.
Making Configuration Changes
Configurable parameters have a dialog box or a drop-down list. Once a configuration
change has been made on a page, click the ‘SAVE SETTINGS’ or ‘NEXT’ button at the
bottom of the page to make the new settings active.
Note: To ensure proper screen refresh after a command entry, check that Internet Explorer
5.0 is configured as follows: Under the menu Tools/Internet
Options/General/Temporary Internet Files/Settings, the setting for ‘Check for newer
versions of stored pages’ should be ‘Every visit to the page.’
24
System Settings
Time Settings
EN
Set the time zone and time server for the ADSL Modem Multiservices PSTN Voice.
This information is used for log entries and client access control.
Check ‘Enable Automatic Time Server Maintenance’ to automatically maintain the
ADSL Modem Multiservices PSTN Voice’s system time by synchronizing with a public
time server over the Internet. Then configure two different time servers by selecting
the options in the Primary Server and Secondary Server fields.
Password Settings
Use this page to restrict access based on a password. By default, there is no
password. For security you should assign one before exposing the ADSL Modem
Multiservices PSTN Voice to the Internet.
Passwords can contain from 3 to12 alphanumeric characters and are not case
sensitive.
Note: If your password is lost, or you cannot gain access to the user interface, press the
reset button (colored blue) on the rear panel (holding it down for at least
five seconds) to restore the factory defaults. (By default there is no password.)
25
EN
Enter a maximum Idle Time Out (in minutes) to define a maximum period of time an
inactive login session will be maintained. If the connection is inactive for longer than
the maximum idle time, it will be logged out, and you will have to login to the web
management system again. (Default: 10 minutes)
Remote Management
By default, management access is only available to users on your local network.
However, you can also manage the ADSL Modem Multiservices PSTN Voice from a
remote host by entering the IP address of a remote computer on this screen.
Check the Enabled check box, and enter the IP address of the Host Address and click
‘SAVE SETTINGS.’
Note: If you check ‘Enabled’ and specify an IP address of 0.0.0.0, any host can manage the
ADSL Modem Multiservices PSTN Voice.
For remote management via WAN IP address you need to connect using port 8080.
Simply enter WAN IP address followed by :8080 in the address field of your web
browser, for example, 212.120.68.20:8080.
DNS
Domain Name Servers are used to map a domain name (e.g., www.somesite.com) to
the equivalent numerical IP address (e.g., 64.147.25.20). Your ISP should provide the
IP address of one or more Domain Name Servers. Enter those addresses on this
page.
26
WAN
EN
Specify the WAN connection parameters provided by your Internet Service Provider
(ISP). The ADSL Modem Multiservices PSTN Voice can be connected to your ISP in
one of the following ways:
• ATM PVC
• Clone MAC
ATM PVC
The ADSL Modem Multiservices PSTN Voice uses ATM as its WAN interface.
Click on each ATM VC for WAN configuration.
See the table below for a description of the parameters.
Parameter
Description
VPI/VCI
Encapsulation
VC-MUX
Circuit
LLC
Protocol
Description
Click on the VC to set the values for the connection.
Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI).
Specifies how to handle multiple protocols at the ATM transport layer.
Point-to-Point Protocol over ATM Virtual
Multiplexer (null encapsulation) allows only one protocol running per
virtual circuit with less overhead.
Point-to-Point Protocol over ATM Logical Link Control (LLC) allows
multiple protocols running over one virtual circuit (using slightly more
overhead).
Protocol used for the connection.
27
ATM Interface
EN
Clicking on the ATM VC brings up the following screen. The ADSL Modem
Multiservices PSTN Voice uses ATM as its WAN interface. Protocols including
1483 Routing, 1483 Bridging, MAC Encapsulated Routing (MER), PPPoA and PPPoE
with LLC-SNAP and VC-Mux encapsulations are supported for each ATM PVC.
When you have finished entering your connection parameters, click ‘SAVE SETINGS.’
You can verify that you have established an ADSL connection by clicking Status at the
bottom of the left-hand menu. See ‘Status’ on page 23.
See the table below for a description of the parameters.
Parameter
Protocol
Description
Disable
1483 Bridging
Disables the connection.
Bridging is a standardized layer 2 technology. It is typically used in
corporate networks to extend the physical reach of a single LAN
segment and increase the number of stations on a LAN without
compromising performance. Bridged data is encapsulated using
the RFC1483 protocol to enable data transport.
Point-to-Point Protocol over ATM is a method of encapsulating
data for transmission to a far point.
1483 Routing allows a simple, low-cost connection to the
Internet via a standard Ethernet port. The router looks up the
network address for each packet seen on the LAN port. If the
address is listed in the routing table as local, it is filtered. If the
address is listed under the ADSL port, it is forwarded. Or if the
address is not found, then it is automatically forwarded to the
default router (i.e., the ADSL Modem Multiservices PSTN Voice
at the head end).
Point-to-Point over Ethernet is a common connection method
used for xDSL.
PPPoA
1483 Routing
PPPoE
MAC Encapsulated
Routing
VPI/VCI
28
If your ADSL service is a Bridged mode service and you want
to share the connection to multiple PC’s, please select MAC
Encapsulated Routing. MER is a protocol that allows you do IP
routing with NAT enabled.
See Virtual Path Identifier (VPI) and Virtual Circuit Identifier
(VCI). Data flows are broken up into fixed length cells, each of
which contains a Virtual Path Identifier (VPI) that identifies the
path between two nodes, and a Virtual Circuit Identifier (VCI)
that identifies the data channel within that virtual path. Each
virtual circuit maintains a constant flow of cells between the
two end points. When there is no data to transmit, empty cells
are sent. When data needs to be transmitted, it is immediately
inserted into the cell flows.
Parameter
Encapsulation
VC-MUX
LLC
Parameter
Encapsulation
VC-MUX
LLC
QoS Class ATM
PCR/SCR/MBS
IP assigned by ISP
IP Address
Subnet Mask
Connect Type
Idle Time
(minutes)
Username
Password
Confirm Password
MTU
Description
Shows the packet encapsulation type.
Packet encapsulation specifies how to handle multiple protocols at
the ATM transport layer.
Point-to-Point Protocol over ATM Virtual Circuit Multiplexer (null
encapsulation) allows only one protocol running per virtual circuit
with less overhead.
Point-to-Point Protocol over ATM Logical Link Control allows
multiple protocols running over one virtual circuit (using slightly
more overhead).
EN
Description
Shows the packet encapsulation type.
Packet encapsulation specifies how to handle multiple protocols at
the ATM transport layer.
Point-to-Point Protocol over ATM Virtual Circuit Multiplexer (null
encapsulation) allows only one protocol running per virtual circuit
with less overhead.
Point-to-Point Protocol over ATM Logical Link Control allows
multiple protocols running over one virtual circuit (using slightly
more overhead).
QoS classes including CBR, UBR and VBR.
QoS Parameters - PCR (Peak Cell Rate), SCR (Sustainable Cell
Rate) and MBS (Maximum Burst Size) are configurable.
Select Yes if the IP address was provided by your ISP.
If your IP address is assigned by the ISP each time you connect,
leave this field all zeros. Otherwise, enter your ISP supplied static
IP address here.
If your subnet mask is assigned by the ISP each time you connect,
leave this field all zeros. Otherwise, enter your subnet mask here.
Sets connection mode to always connected, automatic or manual
connection.
Enter the maximum idle time for the Internet connection.
After this time has been exceeded the connection will be
terminated.
Enter user name.
Enter password.
Confirm password.
Leave the Maximum Transmission Unit (MTU) at the default value
(1500) unless you have a particular reason to change it.
Clone MAC Address
Clicking on the Clone MAC Address brings up the following screen.
29
EN
Some ISPs may require that you register your MAC address with them. If this is the
case, the MAC address of the ADSL Modem Multiservices PSTN Voice must be
changed manually to the MAC address that you have registered with your ISP.
LAN
Use the LAN menu to configure the LAN IP address and to enable the DHCP server
for dynamic client address allocation.
30
Parameter
LAN IP
Description
IP Address
IP Subnet Mask
DHCP Server
DHCP (Dynamic
Host Configuration
Protocol) Server
The IP address of the ADSL Modem Multiservices PSTN Voice.
The subnet mask of the ADSL Modem Multiservices PSTN Voice.
To dynamically assign an IP address to client PCs, enable the
Parameter
LAN IP
Description
IP Address
IP Subnet Mask
DHCP Server
DHCP (Dynamic
Host Configuration
Protocol) Server
The IP address of the ADSL Modem Multiservices PSTN Voice.
The subnet mask of the ADSL Modem Multiservices PSTN Voice.
To dynamically assign an IP address to client PCs, enable the
Lease Time Set the DHCP lease time.
Lease Time Set the DHCP lease time.
IP Address Pool Start IP
EN
End IP Domain Name
Specify the start IP address of the DHCP pool. Do not include the gateway address of
the ADSL Modem Multiservices PSTN Voice in the client address pool. (See ‘TCP/IP
Configuration’ on page 11). If you attempt to include the ADSL Modem Multiservices
PSTN Voice gateway address (192.168.2.1 by default) in the DHCP pool, an error
dialog box will appear. If you change the pool range, make sure the first three octets
match the gateway’s IP address, i.e., 192.168.2.xxx.
Specify the end IP address of the DHCP pool.
If your network uses a domain name, enter it here. Otherwise, leave this field blank.
Remember to configure your client PCs for dynamic address allocation. (See ‘TCP/IP
Configuration’ on page 11 for details.)
Wireless
The ADSL Modem Multiservices PSTN Voice also operates as a wireless access point,
allowing wireless computers to communicate with each other. To configure this
function, you need to enable the wireless function, define the radio channel, the
domain identifier, and the security options.
Wireless Settings
Check Enable and click ‘SAVE SETTINGS.’
Channel and SSID
You must specify an Service Set ID (SSID) and a common radio channel to be used by
the ADSL Modem Multiservices PSTN Voice and all of its wireless clients. Be sure
you configure all of its clients to the same values. The SSID is case-sensitive and can
consist of up to 32 alphanumeric characters. Functioning as an access point, the
Gateway can be configured for roaming clients by setting the SSID and wireless
channel.
31
See the description of the parameters below.
EN
Parameter
SSID
SSID Broadcast
Wireless Mode
Channel
Description
Service Set ID. The SSID must be the same on the ADSL Modem
Multiservices PSTN Voice and all of its wireless clients.
Note: The SSID is case sensitive and can consist of up to
32 alphanumeric characters. (Default: WLAN)
Enable or disable the broadcasting of the SSID. Enable SSID
broadcasting on the wireless network for easy connection with
client PCs. For security reasons, you should disable SSID broadcast.
(Default: Enable)
This device supports both 11g and 11b wireless networks. Make
your selection depending on the type of wireless network that you
have.
The radio channel used by the wireless router and its clients to
communicate with each other. This channel must be the same on
the ADSL Modem Multiservices PSTN Voice and all of its wireless
clients.
The ADSL Modem Multiservices PSTN Voice will automatically
assign itself a radio channel, or you may select one manually.
Note: If you experience poor performance, you may be encountering
interference from another wireless device. Try changing the
channel, as this may eliminate interference and increase
performance. Channels 1, 6, and 11, as the three non-overlapping
channels in the 2.4GHz range, are preferred.
The available channel settings are limited by local regulations.
(Default: Auto; Range: 1-11)
32
Access Control
Using the Access Control functionality, you can specify which PCs can wirelessly
connect to the access point. Each PC has a unique identifier known as a Medium
Access Control (MAC) address. With MAC filtering enabled, only the computers
whose MAC address you have listed in the filtering table may connect to the ADSL
Modem Multiservices PSTN Voice.
EN
See the description of the Access Control features below.
Parameter
Enable MAC Filtering
Access Rule for registered
MAC address
MAC Filtering Table
(up to 32 stations)
Description
Enable or disable the MAC filtering function.
When MAC filtering is enabled, all registered MAC
addresses are controlled by the Access Rule.
Lists allowed MAC addresses.
33
EN
Security
It is important to be aware of security issues, especially when using wireless.
You can configure your security settings on this page.
If you are transmitting sensitive data across radio channels, you should enable
wireless security.
For a more secure network, the ADSL Modem Multiservices PSTN Voice can
implement one or a combination of the following security mechanisms:
• No WEP, No WPA*
• WEP Only
• WPA Only
*) Selecting the No WEP, No WPA option will bring you directly to the 802.1x
configuration page.
The security mechanisms that may be employed depend on the level of security
required, the network and management resources available, and the software support
provided on wireless clients. A summary of wireless security considerations is listed
in the following table.
Security
WEP
WPA
802.1X
34
Client Support
Built-in support
on all 802.11b and
802.11g devices
Requires WPAenabled system and
network card driver
(native support
provided in
Windows XP)
Requires WPAenabled system and
network card driver
(native support
provided in
Windows XP)
Implementation Considerations
• Only provides weak security.
•Requires manual key management.
• Provides good security in small networks.
• Requires configured RADIUS server, or
manual management of pre-shared key.
• Provides robust security in WPA-only mode
(i.e., WPA clients only).
• Requires configured RADIUS server.
• 802.1x Extensible Authentication Protocol (EAP)
type may require management of digital certificates
for clients and server.
WEP
Wired Equivalent Privacy (WEP) encryption requires you to use the same set of
encryption/decryption keys for the router and all of your wireless clients.
EN
See the description of the Access Control features below.
Parameter
WEP
Description
WEP Mode
Key Entry Method
You can choose disabled, 64-bit or 128-bit encryption.
When MAC filtering is enabled, all registered MAC addresses are
controlled by the Access Rule.
Select static key or dynamic key.
Key Provisioning
Static WEP Key
Setting
Default Key ID
Passphrase
Key 1-4
You may manually enter the keys or automatically generate
encryption keys. To manually configure the keys, enter 10 digits for
each 64-bit key, or enter 26 digits for the single 128¬bit key.
(A hexadecimal digit is a number or letter in the range 0-9 or A-F.)
Select the default key.
For automatic key generation, check the Passphrase box, enter a
passphrase and click ‘SAVE SETTINGS.’
If you do not choose to use the Passphrase for automatic key
generation, you must manually enter four keys. For 64-bit
encryption, enter exactly 10 digits. For 128-bit encryption,
enter exactly 26 digits.
(A hexadecimal digit is a number or letter in the range 0-9 or A-F.)
Click ‘SAVE SETTINGS’ to apply your settings.
35
EN
WPA
Wi-Fi Protected Access (WPA) combines Temporal Key Integrity Protocol (TKIP)
and 802.1x mechanisms. It provides dynamic key encryption and 802.1x
authentication service. With TKIP, WPA uses 48-bit initialization vectors, calculates
an 8-byte message integrity code, and generates an encryption key periodically. For
authentication, it allows you to use 802.1x authentication for an environment with a
RADIUS server installed on your network. Selecting the Pre-shared Key enables
WPA to use the pre-shared key in a SOHO network.
See the description of the WPA settings below.
Field Default
Cypher suite TKIP
Parameter
Authentication 802.1X
802.1x
Pre-shared Key
Pre-shared key
Pre-shared Key
characters.
Group Key
36
Passphrase
(8~63 characters)
Passphrase
Hex
None
Disable
Description
One of the security mechanisms used by
WPA for frame body and CRC frame
encryption.
Select the authentication mode:
It is for an enterprise network with a
RADIUS server installed.
It is for a SOHO network without any
authentication server installed.
Select the key type: type
Input 8~63 characters.
Input 64 hexadecimal digits. (A hexadecimal
digit is a number or letter in the range 0-9
or A-F.)
Specify in passphrase style or in 64-Hex
The period of renewing broadcast/multicast
Re_Keying keys.
802.1X
Management access will be checked against the authentication database stored on the
router. If an authentication RADIUS server is used, you must specify the secret key of
the Message-Authenticator attribute, i.e., Message Digest-5 (MD5), and the
corresponding parameters in the RADIUS Server Parameters field for the remote
authentication protocol.
EN
See the description of the 802.1x features below.
Field Default Parameter
Server IP is set to 192.168.2.1
Server Port is set to 1812
Re-Authentication is defined in
3600 seconds period
60 second Quit Period
Seesion idle is set to 300 seconds
before timeout
Server Type RADIUS using 802.1x
security control.
Secret Key set to None
NAS-ID is set to None
Description
The IP address of the RADIUS server.
UDP port used for RADIUS authentication
messages
Defines a maximum period of time for
which the period seconds RADIUS server
will dynamically re-assign a session key to a
connected client station
Defines a maximum period of time for
which the connection is maintained during
inactivity.
Defines a maximum period of time for
which the router will wait between failed
authentications.
Selects the authentication server type.
Secret Key None Defines a text string on
both the RADIUS client and server to
secure RADIUS traffic.The RADIUS server
requires the MD5 Message-Authenticator
attribute for all access request messages.
The 802.1x authentication scheme is
supported by using the Extensible
Authentication Protocol (EAP) over the
RADIUS server.
This defines the request identifier of the
Network Access Server (NAS) or RADIUS
client that is requesting client authentication
from the RADIUS server.
37
EN
NAT
From this section you can configure the Virtual Server, and Special Application
features that provide control over the TCP/ UDP port openings in the router’s
firewall. This section can be used to support several Internet based applications such
as web, email, FTP, and Telnet.
NAT Settings
NAT allows one or more public IP addresses to be shared by multiple internal users.
Enter the Public IP address you wish to share into the Global IP field. Enter a range of
internal IPs that will share the global IP.
Address Mapping
Use Address Mapping to allow a limited number of public IP addresses to be
translated into multiple private IP addresses for use on the internal LAN network.
This also hides the internal network for increased privacy and security.
38
Virtual Server
EN
Using this feature, you can put PCs with public IPs and PCs with private IPs in the
same LAN area.
If you configure the ADSL Modem Multiservices PSTN Voice as a virtual server,
remote users accessing services such as web or FTP at your local site via public IP
addresses can be automatically redirected to local servers configured with private IP
addresses. In other words, depending on the requested service (TCP/UDP port
number), the ADSL Modem Multiservices PSTN Voice redirects the external service
request to the appropriate server (located at another internal IP address).
For example, if you set Type/Public Port to TCP/80 (HTTP or web) and the Private
IP/Port to 192.168.2.2/80, then all HTTP requests from outside users will be
transferred to 192.168.2.2 on port 80. Therefore, by just entering the IP address
provided by the ISP, Internet users can access the service they need at the local
address to which you redirect them.
The more common TCP service ports include:
HTTP: 80, FTP: 21, Telnet: 23, and POP3: 110.
39
EN
Special Applications
Some applications, such as Internet gaming, videoconferencing, Internet telephony and
others, require multiple connections. These applications cannot work with Network
Address Translation (NAT) enabled. If you need to run applications that require
multiple connections, use the following screen to specify the additional public ports to
be opened for each application.
Specify the public port number normally associated with an application in the Trigger
Port field. Set the protocol type to TCP or UDP, then enter the ports that the
application requires. The ports may be in the format 7, 11, 57, or in a range, e.g.,
72-96, or a combination of both, e.g., 7, 11, 57, 72-96.
Popular applications requiring multiple ports are listed in the Popular Applications
field.
From the drop-down list, choose the application and then choose a row number to
copy this data into.
Note: Choosing a row that already contains data will overwrite the current settings.
Example:
ID
1
2
Trigger
Type
6112
28800
Port
Public
UDP
TCP
Trigger
Port
6112
2300-2400,
47624
Public
Type
UDP
TCP
For a full list of ports and the services that run on them, see
www.iana.org/assignments/port-numbers.
40
Comment
Battle.net
MSN Game Zone
NAT Mapping Table
EN
NAT Mapping Table displays the current NAPT address mappings. The NAT address
mappings are listed 20 lines per page, click the control buttons to move forwards and
backwards. As the NAT mapping is dynamic, a Refresh button is provided to refresh
the NAT Mapping Table with the most up-to-date values.
The content of the NAT Mapping Table is described as follows:
• Protocol - protocol of the flow.
• Local IP - local (LAN) host’s IP address for the flow.
• Local Port - local (LAN) host’s port number for the flow.
• Pseudo IP - translated IP address for the flow.
• Pseudo Port - translated port number for the flow.
• Peer IP - remote (WAN) host’s IP address for the flow.
• Peer Port - remote (WAN) host’s port number for the flow.
Route
These pages define routing related parameters, including static routes and Routing
Information Protocol (RIP) parameters.
41
Static Route Parameters
EN
Parameter
Index
Network Address
Subnet Mask
Gateway
Configure
Description
Displays the number of the route.
Enter the IP address of the remote computer for which to set a
static route.
Enter the subnet mask of the remote network for which to set a
static route.
Enter the WAN IP address of the gateway to the remote network.
Allows you to modify or delete configuration settings.
Click Add to display the following page and add a new static route to the list.
Parameter
Index
Network Address
Subnet Mask
Gateway
Configure
42
Description
Displays the number of the route.
Enter the IP address of the remote computer for which to set a
static route.
Enter the subnet mask of the remote network for which to set a
static route.
Enter the WAN IP address of the gateway to the remote network.
Allows you to modify or delete configuration settings.
RIP Parameter
The device supports RIP v1 and v2 to dynamically exchange routing information with
adjacent routers.
EN
Parameter
Description
General RIP Parameters
RIP mode
Auto summary
Globally enables or disables RIP.
If Auto summary is disabled, then RIP packets will include subnetwork information from all sub¬networks connected to the
ADLS Router. If enabled, this sub-network information will be
summarized to one piece of information covering all sub-networks.
Table of current Interface RIP parameter
Interface
Operation Mode
Version
Poison Reverse
The WAN interface to be configured.
Disable: RIP disabled on this interface.
Enable: RIP enabled on this interface.
Silent: Listens for route broadcasts and updates its route table.
It does not participate in sending route broadcasts.
Sets the RIP version to use on this interface.
A method for preventing loops that would cause endless
retransmission of data traffic.
Authentication Required
• None: No authentication.
• Password: A password authentication key is included in the packet. If this does
not match what is expected, the packet will be discarded. This method
provides very little security as it is possible to learn the authentication
key by watching RIP packets.
• MD5: An algorithm that is used to verify data integrity through the creation of a
128-bit message digest from data input (which may be a message of any
length) that is claimed to be as unique to that specific data as a fingerprint is
to a specific individual.
Authentication Code Password or MD5 Authentication key.
RIP sends routing-update messages at regular intervals and when the network
topology changes. When a router receives a routing update that includes changes to
an entry, it updates its routing table to reflect the new route. RIP routers maintain
only the best route to a destination. After updating its routing table, the router
immediately begins transmitting routing updates to inform other network routers of
the change.
43
Routing Table
EN
Parameter
Flags
C
S
R
I
Description
Indicates the route status:
Direct connection on the same subnet.
Static route.
RIP (Routing Information Protocol) assigned route.
ICMP (Internet Control Message Protocol) Redirect route.
Network Destination IP address.
Netmask
The subnetwork associated with the destination.
This is a template that identifies the address bits in the destination
address used for routing to specific subnets. Each bit that
corresponds to a ‘1’ is part of the subnet mask number; each bit
that corresponds to ‘0’ is part of the host number.
Gateway
The IP address of the router at the next hop to which frames are
forwarded.
Interface
The local interface through which the next hop of this route is
reached.
Metric
When a router receives a routing update that contains a new or
changed destination network entry, the router adds 1 to the metric
value indicated in the update and enters the network in the routing
table.
44
Firewall
EN
The ADSL Modem Multiservices PSTN Voice’s firewall enables access control of
client PCs, blocks common hacker attacks, including IP Spoofing, Land Attack, Ping of
Death, IP with zero length, Smurf Attack, UDP port loopback, Snork Attack, TCP null
scan, and TCP SYN flooding. The firewall does not significantly affect system
performance and we advise leaving it enabled to protect your network.
Note: After you check the radio button in the ‘Enable or disable Firewall features’ field,
you must click the ‘SAVE SETTINGS’ button to display the list of firewall features.
Access Control
Access Control allows users to define the outgoing traffic permitted or not-permitted
through the WAN interface. In the example above, all incoming and outgoing emails
are blocked. The default is to permit all outgoing traffic. (See the following page for
details.)
The ADSL Modem Multiservices PSTN Voice can also limit the access of hosts within
the local area network (LAN). The MAC Filtering Table allows the ADSL Modem
Multiservices PSTN Voice to enter up to 32 MAC addresses that are not allowed
access to the WAN port.
The following items are displayed on the Access Control screen:
Parameter
Enable Filtering
Normal Filtering Table
Description
Enables or disables the filtering function. Function
Displays the IP address (or an IP address range) filtering table.
Click Add PC on the Access Control screen to view the following page.
45
EN
Access Control Add PC
The settings in the screen shot below will block all email sending and receiving.
Define the appropriate settings for client PC services (as shown above). Click ‘OK’ to
save your settings. The added PC will now appear in the Access Control page.
MAC Filter
Use this page to block access to your network using MAC addresses.
46
The ADSL Modem Multiservices PSTN Voice can also limit the access of hosts within
the local area network (LAN). The MAC Filtering Table allows the ADSL Modem
Multiservices PSTN Voice to enter up to 32 MAC addresses that are allowed access
to the WAN port. All other devices will be denied access.
EN
URL Blocking
To configure the URL Blocking feature, use the table below to specify the web sites
(www.somesite.com) and/or keywords you want to filter on your network.
To complete this configuration, you will need to create or modify an access rule in
‘Access Control’ on page 45. To modify an existing rule, click the Edit option next to
the rule you want to modify. To create a new rule, click on the Add PC option.
From the Access Control, Add PC section, check the option for ‘WWW with URL
Blocking’ in the Client PC Service table to filter out the web sites and keywords
selected below, on a specific PC.
The ADSL Modem Multiservices PSTN Voice allows the user to block access to web
sites from a particular PC by entering either a full URL address or just a keyword.
This feature can be used to protect children from accessing violent or pornographic
web sites.
Schedule Rule
You may filter Internet access for local clients based on rules.
Each access control rule may be activated at a scheduled time. Define the schedule on
the Schedule Rule page, and apply the rule on the Access Control page.
Click Add Schedule Rule.
47
EN
Edit Schedule Rule
You can create and edit schedule rules on this page.
Define the appropriate settings for a schedule rule (as shown on the following
screen). The rule in the screen shot above prohibits emailing after 3.00 pm from
Monday to Thursday. Upon completion, click ‘OK’ to save your schedule rules.
Intrusion Detection
The ADSL Modem Multiservices PSTN Voice’s firewall inspects packets at the
application layer, maintains TCP and UDP session information including timeouts and
number of active sessions, and provides the ability to detect and prevent certain types
of network attacks such as Denial-of-Service (DoS) attacks.
48
EN
Network attacks that deny access to a network device are called DoS attacks.
DoS attacks are aimed at devices and networks with a connection to the Internet.
Their goal is not to steal information, but to disable a device or network so users no
longer have access to network resources.
The ADSL Modem Multiservices PSTN Voice protects against DoS attacks including:
Ping of Death (Ping flood) attack, SYN flood attack, IP fragment attack (Teardrop
Attack), Brute-force attack, Land Attack, IP Spoofing attack, IP with zero length,
TCP null scan (Port Scan Attack), UDP port loopback, Snork Attack.
Note: The firewall does not significantly affect system performance, so we advise enabling
the prevention features to protect your network.
49
EN
Parameter
Enable SPI and
Anti-DoS firewall
protection
Defaults
Yes
Stateful Packet
Inspection
Description
The Intrusion Detection feature of the
Telephony Router limits the access of
incoming traffic at the WAN port. When
the Stateful Packet Inspection (SPI) feature
is turned on, all incoming packets are
blocked except those types marked with a
check in the Stateful Packet Inspection
section at the top of the screen.
This option allows you to select different
application types that are using dynamic
port numbers. If you wish to use Stateful
Packet Inspection (SPI) for blocking packets,
click on the Yes radio button in the ‘Enable
SPI and Anti-DoS firewall protection’ field
and then check the inspection type that you
need, such as Packet Fragmentation, TCP
Connection, UDP Session, FTP Service,
H.323 Service, and TFTP Service.
It is called a ‘stateful’ packet inspection
because it examines the contents of the
packet to determine the state of the
communication; i.e., it ensures that the
stated destination computer has previously
requested the current communication. This
is a way of ensuring that all communications
are initiated by the recipient computer and
are taking place only with sources that are
known and trusted from previous
interactions. In addition to being more
rigorous in their inspection of packets,
stateful inspection firewalls also close off
ports until a connection to the specific port
is requested.
When particular types of traffic are
checked, only the particular type of traffic
initiated from the internal LAN will be
allowed. For example, if the user only
checks FTP Service in the Stateful Packet
Inspection section, all incoming traffic will
be blocked except for FTP connections
initiated from the local LAN.
Hacker Prevention
Discard Ping
from WAN Discard
50
Disabled
Prevents a ping on the router’s WAN port
from being routed to the network.
Parameter
RIP Defect
Defaults
Enabled
Description
If the router does not reply to an IPX RIP
request packet, it will stay in the input
queue and not be released. Accumulated
packets could cause the input queue to fill,
causing severe problems for all protocols.
Enabling this feature prevents the packets
accumulating.
When hackers attempt to enter your
network, we can alert you by email
Enter your email address.
Enter your SMTP server address (usually
the part of the email address following the
‘@’ sign).
Enter your POP3 server address (usually
the part of the email address following the
‘@’ sign).
Enter your email account user name.
Enter your email account password.
Connection Policy
Fragmentation half-open
wait10 secs
TCP SYN
wait 30 secs
TCP FIN
wait 5 secs
TCP connection
3600 secs
UDP session
idle 30 secs
H.323 data timeout
180 secs
Configures the number of seconds that a
packet state structure remains active.
When the timeout value expires, the router
drops the unassembled packet, freeing that
structure for use by another packet.
Defines how long the software will wait for
a TCP session to reach an established state
before dropping the session.
Specifies how long a TCP session will be
managed after the firewall detects a FINexchange.
The length of time for which a TCP session
will be idle timeout (1 hour) managed if
there is no activity.
The length of time for which a UDP session
will timeout be managed if there is no
activity.
The length of time for which an H.323
session will channel idle be managed if
there is no activity.
Parameter
DoS Detect Criteria
Defaults
Your E-mail Address
SMTP Server Address
POP3 Server Address
User Name
Password
Total incomplete
300
Total incomplete
250
Incomplete
250
EN
Description
Defines the rate of new unestablished
sessions that TCP/UDP sessions will cause
the software to start deleting half-open
sessions HIGH sessions.
Defines the rate of new unestablished
sessions that TCP/UDP sessions will cause
the software to stop deleting half-open
sessions LOW sessions.
Maximum number of allowed incomplete
51
EN
Parameter
TCP/UDP sessions
Defaults
Description
TCP/UDP sessions
per minute.
HIGH
Incomplete 200 Minimum number of
allowed incomplete
Maximum 10 Maximum number of
LOW
incomplete TCP/UDP
incomplete sessions from the same host.
TCP/UDP
sessions number
from same host
Incomplete sessions
detect sensitive
time period
Maximum 30
fragmentation
packet
number from
same host
Half-open
fragmentation
detect sensitive
time period
Flooding cracker
300 msecs
Length of time before an incomplete
TCP/UDP TCP/UDP session is detected as
incomplete.
Maximum number of half-open
fragmentation half-open packets
from the same host.
1 secs
Length of time before a half-open
fragmentation session is detected as halfopen.
300 secs
Length of time from detecting a flood
attack to block time blocking the attack.
DMZ
If you have a client PC that cannot run an Internet application properly from behind
the firewall, you can open the client up to unrestricted two-way Internet access.
Enter the IP address of a DMZ (Demilitarized Zone) host on this screen. Adding a
client to the DMZ may expose your local network to a variety of security risks, so
only use this option as a last resort.
52
SNMP
Community
Use the SNMP configuration screen to display and modify parameters for the Simple
Network Management Protocol (SNMP). A computer attached to the network, called
a Network Management Station (NMS), can be used to access this information.
Access rights to the agent are controlled by community strings. To communicate with
the ADSL Modem Multiservices PSTN Voice, the NMS must first submit a valid
community string for authentication.
Parameter
Community
Access
Valid
EN
Description
A community name authorized for management access.
Management access is restricted to Read or Write.
Enables or disables the entry.
Note: Up to 5 community names may be entered.
Trap
Parameter
IP Address
Version
Description
Community
Traps are sent to this address when errors or specific events occur on
the network.
A community string (password) specified for trap management. Enter a
word, something other than public or private, to prevent unauthorized
individuals from reading information on your system.
Sets the trap status to disabled, or enabled with V1 or V2c.
The v2c protocol was proposed in late 1995 and includes
enhancements to v1 that are universally accepted. These include a getbulk command to reduce network management traffic when retrieving
a sequence of MIB variables, and a more elaborate set of error codes
for improved reporting to a Network Management Station.
53
ADSL
EN
ADSL Parameters
We recommend leaving the Operation Mode at the default Automatic setting, to
automatically negotiate with remote DSLAM.
Operation Mode
• Automatic
• T1.413 Issue 2
• G.992.1 (G.DMT)
• G.992.2 (G.Lite)
• G.992.3 (ADSL2)
• G.992.5 (ADSL2+)
Status
The Status page displays ADSL status information.
54
Parameter
Description
Status
• Line Status
Shows the current status of the ADSL line.
Data Rate
• Upstream
• Downstream
Actual and maximum upstream data rate.
Actual and maximum downstream data rate.
Operation Data/Defect Indication
• Noise Margin
- Upstream
- Downstream
• Output Power
• Attenuation
- Upstream
- Downstream
• Fast Path FEC Correction
• Interleaved Path FEC
Correction
• Fast Path CRC Error
• Interleaved Path CRC Error
•
•
•
•
•
Loss of Signal Defect
Loss of Frame Defect
Loss of Power Defect
Fast Path HEC Error
Interleaved Path HEC Error
Statistics
• Received Superframes
Interleaved
• Transmitted Superframes
Interleaved
• Received Superframes Fast
• Transmitted Superframes Fast
EN
Minimum noise margin upstream.
Minimum noise margin downstream.
Maximum fluctuation in the output power.
Maximum reduction in the strength of the upstream
signal.
Maximum reduction in the strength of the
downstream signal.
There are two latency paths that may be used: fast
and interleaved. For either path a forward error
correction (FEC) scheme is employed to ensure
higher data integrity. For maximum noise immunity,
an interleaver may be used to supplement FEC.
An interleaver is basically a buffer used to introduce
a delay, allowing for additional error correction
techniques to handle noise. Interleaving slows the
data flow and may not be optimal for real-time
signals such as video transmission.
Indicates the number of Fast Path Cyclic
Redundancy Check errors.
Indicates the number of Interleaved Path Cyclic
Redundancy Check errors.
Momentary signal discontinuities.
Failures due to loss of frames.
Failures due to loss of power.
Fast Path Header Error Concealment errors.
Interleaved Path Header Error Concealment errors.
(Superframes represent the highest level of data
presentation. Each superframe contains regular
ADSL frames, one of which is used to provide
superframe synchronization, identifying the start of a
superframe. Some of the remaining frames are also
used for special functions.)
Number of interleaved superframes received.
Number of interleaved superframes transmitted.
Number of fast superframes received.
Number of fast superframes transmitted.
55
Telephony
EN
Port Setting
Configure the port settings on this page, and click ‘OK’ to save the parameters.
Telephony providers operate SIP proxies that allow you to register your ADSL
Modem Multiservices PSTN Voice on their system so that your can call friends, family
and business associates. There are many Telephony service providers available. It is
up to you to decide which service provider is best for your needs.
Once you have decided on a provider, you will need to get the following information:
Username, Password, SIP Domain, Realm, SIP Proxy IP, SIP Proxy Port.
See the table below for a description of the parameters.
Parameter
Phone 1/2 Enable
Phone Number
Display Name
SIP Domain
Realm
Username
Password
56
Description
Enable/disable phone 1 and/or 2.
Your phone number.
Your name, often the same as your phone number.
(From your Telephony provider, e.g., ‘sipcenter.com’ or an
IP address.)
(From your Telephony provider.)
(From your Telephony provider.)
(From your Telephony provider.)
SIP Setting
Configure your SIP parameters on this page, and click ‘OK’ to apply them.
EN
SIP, the Session Initiation Protocol, is a signaling protocol for Internet conferencing,
telephony, presence, events notification and instant messaging. The call waiting feature
allows the user to take an incoming call, even though the user is already on the
phone. The user upon hearing the new call, can put the original caller on hold and
speak to the new caller. When the user hasn’t finished talking to the new caller, he
can resume his conversation with the original caller.
According to the SIP RFC, a proxy server is ‘An intermediary entity that acts as both
a server and a client for the purpose of making requests on behalf of other clients. A
proxy server primarily plays the role of routing, which means its job is to ensure that
request is sent to another entity ‘closer’ to the targeted user.’
The proxy server therefore, is an intermediate device that receives SIP requests from
a client and then forwards the requests on the client’s behalf. Proxy servers receive
SIP messages and forward them to the next SIP server in the network. A series of
proxy and redirect servers receive requests from a client and decide where to send
these requests. Proxy servers can provide functions such as authentication,
authorization, network access control, routing, reliable request retransmission, and
security.
From the SIP RFC, ‘A registrar is a server that accepts REGISTER requests and places
the information it receives in those requests into the location service for the domain
it handles.’
See the table below for a description of the parameters.
Parameter
SIP Listen Port
Support Call
Proxy Setting
• Proxy IP
• Proxy Port
Registrar Setting
• Registrar IP
• Registrar Port
Description
It is strongly recommended that you to leave the SIP port
unchanged (Default: 5060).
Enables or disables support for call waiting.
Waiting (Default: Disabled)
Set the proxy settings.
IP address of your proxy server. (From your Telephony provider.)
Port number of the proxy server. (From your Telephony provider.)
Set the registrar settings.
IP address of SIP registrar.
Port number of SIP registrar.
57
Telephony Advanced Setting
EN
Configure the Telephony advanced settings on this page, and click ‘OK.’
SIP is a peer-to-peer protocol. The peers in a session are called User Agents (UAs).
A user agent can function in one of the following roles:
1. User agent client (UAC) - A client application that initiates the SIP request.
2. User agent server (UAS) - A server application that contacts the user when a SIP
request is received and that returns a response on
behalf of the user.
Typically, an SIP end point is capable of functioning as both a UAC and a UAS, but
functions only as one or the other per transaction.
Phone standards vary internationally, so it is important that the ADSL Modem
Multiservices PSTN Voice is configured for the correct country.
Codecs are used to convert an analog voice signal to digitally encoded version.
Codecs vary in the sound quality, the bandwidth required, the computational
requirements, etc. You can specify which audio coding process you would like to use.
There are four voice codecs supported by the ADSL Modem Multiservices PSTN
Voice, you may try different settings to determine the best audio quality you obtain
from the combination of your network connection and your used audio device (head
set or hand set). The default codec sequence is listed below. You can use the Up and
Down buttons to change priority.
1.
2.
3.
4.
58
G.711 A law
G.711 U law
G.729
G.723.3
See the table below for a description of the parameters.
Parameter
Support Call
Support User-Agent
Telephony Hook
Telephony Tone
Voice Codec
Configuration
• Available Codecs
• Selected Codecs
Description
Enables or disables support for call waiting.
Waiting (Default: Disabled)
Enables or disables user-agent header support. Enabling this
Header feature includes user agent information in the packet,
e.g., the caller’s ID may be displayed. (Default: Disabled)
The hook flash timer is the length of time before the hook
Flash Timer flash indicates a time-out (or call disconnect).
(Default: 800 milliseconds.)
Select the country. Country Setting
Set the voice codecs.
EN
List of available codecs.
List of selected codecs.
Dialing Plans
Configure the Telephony dialing plans on this page, and click ‘SAVE SETTINGS.’
Set the Phone Number and Connection Type on this page.
Telephony Status
View the Telephony status for both FXS ports on this page.
Click ‘Refresh’ to update this page.
This page displays the Port Type, SIP URL and Registration status of the ADSL
Modem Multiservices PSTN Voice.
59
See the table below for a description of the parameters.
EN
Parameter
Port Type
SIP URL
Registration
Description
Displays the port type, i.e., FXS.
Shows the SIP URL.
Indicates whether the user has successfully registered or not.
Telephony Call Logs
View the call log for both FXS ports on this page. Click ‘Refresh’ to update the page.
See the table below for a description of the parameters.
Parameter
Parameter
Port Type
Received Call
Dialed Call
Rejected Call
Forwarded Call
Description
Description
Displays the port type, i.e., FXS.
Number of received calls.
Number of calls made.
Number of rejected calls.
Number of forwarded calls.
Maintenance
Check Backup Router Configuration and click ‘NEXT’ to save your ADSL Modem
Multiservices PSTN Voice’s configuration to a file named ‘backup.bin’ on your PC.
You can then check Restore from saved Configuration file (backup.bin) to restore the
saved backup configuration file.
To restore the factory settings, check Restore router to Factory Defaults and click
‘NEXT.’ You will be asked to confirm your decision. Click ‘APPLY’ to proceed, or
‘CANCEL’ to go back.
60
Firmware Upgrade
Use this screen to update the firmware or user interface to the latest versions.
EN
Download the file to your hard drive. Then click Browse... to find the file on your
computer. Select the firmware file and click ‘Open.’ Click ‘BEGIN UPGRADE’ to start
the upgrade process.
Reset
Perform a reset from this page.
Should your unit become unresponsive for any reason, you can simply perform a
reset from this page. Performing a reset will reboot the device. Your configuration
settings will remain the same.
61
EN
Status
The Status screen displays WAN/LAN connection status, firmware and hardware
version numbers, as well as information on DHCP clients connected to your network.
The security log may be saved to a file by clicking ‘Save’ and choosing a location.
The following items are included on the Status screen:
Parameter
INTERNET
Release
Renew
GATEWAY
INFORMATION
ATM PVC
Security Log
Save
Clear
Refresh
DHCP Client Log
62
Description
Displays WAN connection type and status.
Click on this button to disconnect from the WAN.
Click on this button to establish a connection to the WAN.
Displays system IP settings, as well as DHCP Server and
Firewall status
Displays the number of attached clients, the firmware versions,
the physical MAC address for each media interface and for the
ADSL Modem Multiservices PSTN Voice, as well as the
hardware version and serial number.
Displays ATM connection type and status.
Displays illegal attempts to access your network.
Click on this button to save the security log file.
Click on this button to delete the access log.
Click on this button to refresh the screen.
Displays information on DHCP clients on your network.
Troubleshooting
EN
This section describes common problems you may encounter and possible solutions
to them. The ADSL Modem Multiservices PSTN Voice can be easily monitored
through panel indicators to identify problems.
Problem
LED Indicators
POWER LED is Off
Solution
• Check connections between the ADSL Modem Multiservices
PSTN Voice, the external power supply, and the wall outlet.
• If the power indicator does not turn on when the power
cord is plugged in, you may have a problem with the power
outlet, power cord, or external power supply. However, if
the unit powers off after running for a while, check for loose
power connections, power losses, or surges at the power
outlet. If you still cannot isolate the problem, then the
external power supply may be defective. In this case, contact
Technical Support for assistance.
LAN LED is Off
• Verify that the ADSL Modem Multiservices PSTN Voice and
attached device are powered on.
• Be sure the cable is plugged into both the ADSL Modem
Multiservices PSTN Voice and the corresponding device.
• Verify that the proper cable type is used and that its length
does not exceed the specified limits.
• Be sure that the network interface on the attached device is
configured for the proper communication speed and duplex
mode.
• Check the adapter on the attached device and cable
connections for possible defects. Replace any defective
adapter or cable if necessary.
Network Connection Problems
Cannot ping the
• Verify that the IP addresses are properly configured.
ADSL Modem
For most applications, you should use the ADSL Modem
Multiservices PSTN
Multiservices PSTN Voice’s DHCP function to dynamically
Voice from the
assign IP addresses to hosts on the attached LAN. However,
attached LAN, or it
if you manually configure IP addresses on the LAN, verify
cannot ping any device
that the same network address (network component of the
on the attached LAN
IP address) and subnet mask are used for both the ADSL
Modem Multiservices PSTN Voice and any attached LAN
devices.
• Be sure the device you want to ping (or from which you are
pinging) has been configured for TCP/IP.
Management Problems
Cannot connect
• Be sure to have configured the ADSL Modem Multiservices
using the Web browser
PSTN Voice with a valid IP address, subnet mask, and default
gateway.
• Check that you have a valid network connection to the
ADSL Modem Multiservices PSTN Voice and that the port
you are using has not been disabled.
• Check the network cabling between the management station
and the ADSL Modem Multiservices PSTN Voice.
Forgot or lost the
• Press the Reset button on the rear panel (holding it down
password
for at least five seconds) to restore the factory defaults.
63
EN
Glossary
10BASE-T
IEEE 802.3 specification for 10 Mbps Ethernet over two pairs of Category 3, 4, or 5
UTP cable.
100BASE-TX
IEEE 802.3u specification for 100 Mbps Fast Ethernet over two pairs of Category 5
UTP cable.
Auto-Negotiation
Signalling method allowing each node to select its optimum operational mode (e.g., 10
Mbps or 100 Mbps and half or full duplex) based on the capabilities of the node to
which it is connected.
Bandwidth
The difference between the highest and lowest frequencies available for network
signals. Also synonymous with wire speed, the actual speed of the data transmission
along the cable.
Collision
A condition in which packets transmitted over the cable interfere with each other.
Their interference makes both signals unintelligible.
Collision Domain
Single CSMA/CD LAN segment.
CSMA/CD
CSMA/CD (Carrier Sense Multiple Access/Collision Detect) is the communication
method employed by Ethernet, Fast Ethernet, or Gigabit Ethernet.
End Station
A workstation, server, or other device that does not forward traffic.
Ethernet
A network communication system developed and standardized by DEC, Intel, and
Xerox, using baseband transmission, CSMA/CD access, logical bus topology, and
coaxial cable. The successor IEEE 802.3 standard provides for integration into the OSI
model and extends the physical layer and media with repeaters and implementations
that operate on fiber, thin coax and twisted-pair cable.
Fast Ethernet
A 100 Mbps network communication system based on Ethernet and the CSMA/CD
access method.
Full Duplex
Transmission method that allows two network devices to transmit and receive
concurrently, effectively doubling the bandwidth of that link.
IEEE
Institute of Electrical and Electronic Engineers.
IEEE 802.3
Defines carrier sense multiple access with collision detection (CSMA/CD) access
method and physical layer specifications.
IEEE 802.3ab
Defines CSMA/CD access method and physical layer specifications for 1000BASE-T
Fast Ethernet.
IEEE 802.3u
Defines CSMA/CD access method and physical layer specifications for 100BASE-TX
Fast Ethernet.
IEEE 802.3x
Defines Ethernet frame start/stop requests and timers used for flow control on fullduplex links.
Local Area Network (LAN)
A group of interconnected computer and support devices.
LAN Segment
Separate LAN or collision domain.
LED
Light emitting diode used or monitoring a device or network condition.
64
Local Area Network
A group of interconnected computers and support devices.
EN
Media Access Control (MAC)
A portion of the networking protocol that governs access to the transmission
medium, facilitating the exchange of data between network nodes.
MIB
An acronym for Management Information Base. It is a set of database objects that
contains information about the device.
RJ-45 Connector
A connector for twisted-pair wiring.
Straight-through Port
An RJ-45 port which does not cross the receive and transmit signals internally (MDI)
so it can be connected with straight-through twisted-pair cable to any device having a
crossover port (MDI-X). Also referred to as a ‘Daisy-Chain’ port.
The RJ-45, 10/100 Mbps port supports Auto MDI/ MDI-X.
Switched Ports
Ports that are on separate collision domains or LAN segments.
UTP
Unshielded twisted-pair cable.
65
EN
Specifications
Standards Compliance
CE Mark
Emissions
FCC Class B, VCCI Class B
Industry Canada Class B
EN55022 (CISPR 22) Class B
C-Tick - AS/NZS 3548 (1995) Class B
Immunity
EN 61000-3-2/3
EN 61000-4-2/3/4/5/6/8/11
Safety
UL 1950
EN60950 (TÜV)
CSA 22.2 No. 950
IEEE 802.3 10 BASE-T Ethernet
IEEE 802.3u 100 BASE-TX Fast Ethernet
Modem Standards
ITU G.992.1 (G.dmt)
ITU G.992.2 (G.lite)
ITU G.994.1 (G.handshake)
ITU T.413 issue 2 - ADSL full rate
LAN Interface
1 RJ-45 10 BASE-T/100 BASE-TX port
Auto-negotiates the connection speed to 10 Mbps Ethernet or 100 Mbps
Fast Ethernet, and the transmission mode to half-duplex or full-duplex
USB Interface
1 USB port
SPECIFICATIONS
C-2
WAN Interface
1 ADSL RJ-11 port
FXS Interface
2 FXS ports
Indicator Panel
Phone 1-2, VoIP, USB, LAN, Online, ADSL, PWR (power)
Dimensions
1560 x 1280 x 280 mm
Weight
0.425 Kg
Input Power
12 V 1.25 A
Power Consumption
2.52 Watts maximum
Advanced Features
VoIP - QoS, VAD, call waiting, call forwarding, caller ID, jitter buffer.
Codecs supported - G.7.11 U/A law, G.7.29, G.723.1
Dynamic IP Address Configuration – DHCP, DNS, DDNS
Firewall – Client privileges, hacker prevention and logging,
Stateful Packet Inspection
Internet Standards
RFC 826 ARP, RFC 791 IP, RFC 792 ICMP, RFC 768 UDP, RFC 793 TCP,
RFC 783 TFTP, RFC 1483 AAL5 Encapsulation, RFC 1661 PPP,
RFC 1866 HTML, RFC 2068 HTTP, RFC 2364 PPP over ATM
Temperature
Operating 0 to 40 °C (32 to 104 °F)
Storage -40 to 70 °C (-40 to 158 °F)
Humidity
5% to 95% (non-condensing)
66
0682
Specifications are subject to change without notice.
Trademarks are the property of Koninklijke Philips Electronics N.V. or their respective owners.
2005 © Koninklijke Philips Electronics N.V. All rights reserved.
www.philips.com
DFU-SNV6520-ENG-V1.0