Sharp AD-USB1 Specifications

BatteryBar™
Quick Start Guide
Model # PP2016/PP2008
04-13
IMPORTANT SAFETY INFORMATION
Please read this manual in its entirety before operating your Bushnell POWERSYNC product. It contains
important information concerning the setup, operation and maintenance of the product. Keep this
manual for future reference.
• WARNING: This product should only be used with the supplied charging unit and accessories
(not included with all models). Use of a charger or accessories not recommended or supplied by
Bushnell may result in product damage, fire, electrical shock or injury, and will void your product
warranty.
• CAUTION: Do not use the product to charge an external device at the same time as the internal
battery is being charged by the AC wall charger.
• CAUTION: Do not operate the product in an environment where temperatures exceed 112o F/45o C
• CAUTION: Do not submerge the product in water, or attempt to operate the product after it has
been exposed to water.
• CAUTION: Do not attempt to open the product. There are no user serviceable internal parts.
Disassembling the product will void your warranty. The rechargeable battery must be replaced
by a qualified technician.
• CAUTION: Check adaptors for correct fit and compatibility before using the product to charge
electronic devices. Improperly used adaptors can be a shock hazard and may damage the
electronic device.
• CAUTION: Before operating the product or connecting it to any other device, check to ensure that
all cables are not damaged. Extreme heat, water, petroleum products and sharp edges all have
the potential to damage cables. Do not use any cable with exposed wiring.
• CAUTION: Charge your connected devices in an area away from the direct sun if possible.
• WARNING: EXPLOSION HAZARD! - Do not incinerate any Bushnell POWERSYNC product, or
attempt to use it in a microwave oven.
• WARNING: Bushnell POWERSYNC products are not intended for powering any medical
equipment, life support devices, or any other critical equipment.
• CAUTION: Do not clean your Bushnell POWERSYNC product with anything other than a damp rag.
The use of cleaning chemicals or other products may harm the unit and will void your warranty.
• Do not dispose of any Bushnell POWERSYNC product as you would normal household trash.
Please contact your local government authority for directions regarding the proper disposal of
products containing a Lithium Ion battery.
PACKING LIST
2
This POWERSYNC model includes the following items:
• BatteryBar (Model PP2016 or PP2008)
• USB Cable
• AC Wall Charger (with PP2016 only)
• Quick Start Guide
AC Wall Charger
with USB cable connected
(not included w/PP2008)
HOW THE BatteryBar WORKS
The BatteryBar™ uses a lithium ion battery to store electrical energy, so it
can be used to recharge your portable electronic devices anywhere, anytime.
The BatteryBar’s battery is charged from an AC outlet (PP2016) or the USB
port on your computer (PP2008), so it’s ready to provide immediate power on
demand whenever you’re away from your home or campsite.
FROM CHARGER (PP2016)
or PC (PP20008) USB PORT**
OUTPUT-Used for charging your device(s)
from the BatteryBar’s internal battery (once
charged via AC wall charger or PC)
(standard USB plug)
TO BatteryBar
INPUT PORT
B
(micro USB plug)
PP2016
PP2008
FROM BatteryBar
OUTPUT PORT
(standard USB plug)
INPUT-Used for charging the BatteryBar
internal battery from wall charger or PC.
LEDs indicate charge status.
A
TO PORTABLE DEVICE
CHARGING PORT*
Power
Button
POWERSYNC POWER GAUGE
(LED Battery Status Indicators)
(micro USB plug)
* Use USB charging cable included with your
device if this connector is not compatible.
** compatible with USB power sources
rated at 5V ,1 amp (1000mA)
3
CHARGING THE BATTERYBAR FROM THE WALL CHARGER
Step 1 (Model PP2016): Connect USB cable to micro-USB INPUT port (A) from
the USB port on the supplied AC charger (pg. 2), and plug it into a wall outlet
(100-240v).
Step 1 (Model PP2008): Connect USB cable to micro-USB INPUT port (A) from
a USB port on a computer. Avoid connecting to unpowered USB hubs and
USB ports located on keyboards, etc. to ensure you get full power from the
computer. Make sure the computer is powered from an AC outlet.
Step 2 (PP2016/PP2008): Press the Power button on the BatteryBar. All
four LEDs on the Power Gauge (Fig. 1) will light up (for 10 min.) when the
BatteryBar’s internal battery has been fully charged (you may leave it
connected to the charger overnight without risk of overcharging), and you’re
ready to connect and charge your device.
CHARGING YOUR DEVICE FROM THE BATTERYBAR
Press the power button on the INPUT end of the battery cylinder (A) to check
the BatteryBar’s charge status, then connect the supplied USB cable from the
OUTPUT port (B) of the BatteryBar to your device to recharge it. If your device
uses a non-standard type of connector, use the cable that came with it to
connect to the BatteryBar’s OUTPUT port. Check the charge indicator on your
device to determine when it’s ready to use.
STORING & TRANSPORTING THE BATTERYBAR
Cover the INPUT and OUTPUT ends of the BatteryBar with the attached caps
when storing or transporting the BatteryBar, to help keep dirt and debris out
of the USB ports.
INPUT
OUTPUT
B
A
PP2016
4
PP2008
UNDERSTANDING THE POWERSYNC POWER GAUGE
The 4 LED charge indicators on the INPUT end of the battery cylinder (A)
allow you to monitor the status of the BatteryBar’s internal battery. While
the battery is charging from the AC wall charger, the LEDs will light up in
sequence to show the charge level as shown in Fig. 1. The LED indicating
the current battery level will blink rapidly while charging. When charging is
complete, all LEDs remain on for 10 min., then shut off until the Power button
is pressed.
Blinking
Fig. 1
Charging In
from AC
>25%
>50%
>75%
>90%
FULL
While the BatteryBar is charging your connected device (Power button must
be pressed), the LEDs will monitor the BatteryBar’s battery level as shown in
Fig. 2, with a single LED blinking once every 15 sec. (shows active charging but
conserves battery power).
Slowly Blinking
Fig. 2
Charging Out
to Device
<25%
<50%
<75%
<90%
FULL
You can also check the current level of the BatteryBar’s battery charge
anytime by pressing the Power button, even when it is not connected to
the charger or an external device. The LEDs will glow steadily to indicate the
charge level % as shown in Fig.3. , then shut off after 10 seconds.
Blinking
Fig. 3
Checking
Charge Level
<25%
>25%
>50%
>75%
FULL
5
TECHNICAL SPECIFICATIONS
Model
PP2016 (USB2)
PP2008 (USB1)
Weight
5.9 oz / 167 g
5.4 oz / 153 g
Size
9.2 x 1.4 in.
9.2 x 1.4 in.
Charge Time (Wall
Charger)
approx. 6-8 hrs.
approx. 4-6 hrs.
Power Output
5 volts, 1 amp (1000 mA)
5 volts, 1 amp (1000 mA)
Internal Battery Type
Dual Lith Ion
Single Lith Ion
USB Inputs / Outputs
1 / 2*
1/1
Operating Temp. Range
-4 ~ 112 F (-20~44 C)
-4 ~ 112o F (-20~44o C)
Storage Temp. Range
-4 ~ 140o F (-20~60o C)
-4 ~ 140o F (-20~60o C)
Recommended
Devices/# of Charges**
(from fully charged
internal battery)
Cell Phones (inc Smartphones)/2x,
MP3 Players/3x, Digital Cameras/5x,
Tablet/0.5x Note: Tablets and other
devices have higher power requirements
and may not attain a full charge from
the BatteryBar battery.
Cell Phones (inc Smartphones)/1x, MP3
Players/2x, Digital Cameras/2.5x
Note: Tablets and other devices have
higher power requirements and may not
attain a full charge from the BatteryBar
battery.
o
o
* Two devices may be charged simultaneously. They will not charge any slower than if only one device was connected, however the BatteryBar’s
internal battery charge will be depleted more rapidly.
** Rechargeable batteries in electronic devices charge at different rates, depending on many factors including temperature, age and circuit
design. Bushnell provides examples of charges per device, based on typical product use and are not intended to be specific to any single device.
ATTENTION!
The PP2016/PP2008 is protected from static shock.
If the unit does not turn on after depressing power button, please
hold down power button for 2 seconds or until light activates.
6
Specifications and designs are subject to change without any notice or obligation on the part of the manufacturer.
ONE YEAR LIMITED WARRANTY
Your Bushnell® POWERSYNC product is warranted to be free of defects in materials and workmanship for one year after the date of purchase.
In the event of a defect under this warranty, we will, at our option, repair or replace the product, provided that you return the product
postage prepaid. This warranty does not cover damages caused by misuse, improper handling, installation, or maintenance provided by
someone other than a Bushnell Authorized Service Department.
Any return made under this warranty must be accompanied by the items listed below:
1.
A check/money order in the amount of $10.00 to cover the cost of postage and handling
2.
Name and address for product return
3.
An explanation of the defect
4.
Proof of Date Purchased
5.
Product should be well packed in a sturdy outside shipping carton, to prevent damage in transit, with return postage prepaid
to the address listed below:
IN U.S.A. Send To: Bushnell Outdoor Products
Attn.: Repairs
9200 Cody
Overland Park, Kansas 66214
IN CANADA Send To: Bushnell Outdoor Products
Attn.: Repairs
25A East Pearce Street, Unit 1
Richmond Hill, Ontario L4B 2M9
For products purchased outside the United States or Canada please contact your local dealer for applicable warranty information. In
Europe you may also contact Bushnell at:
Bushnell Germany GmbH
European Service Centre
Mathias-Brüggen-Str. 80
D-50827 Köln
GERMANY
Tél: +49 221 995568-0
Fax: +49 221 995568-20
This warranty gives you specific legal rights.
You may have other rights which vary from country to country.
©2013 Bushnell Outdoor Products
FCC Compliance Statement
This device complies with Part 15 of the FCC interference limits for Class B digital devices FOR HOME OR OFFICE USE. These limits are
designed to provide reasonable protection against harmful interference in a residential installation, and are more stringent than “outdoor”
requirements.
Operation of this device is subject to the following conditions; (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
The device does not contain any user-serviceable parts. Repairs should only be made by an Authorized Bushnell repair center. Unauthorized
repairs or modifications could result in permanent damage to the equipment, and will void your warranty and your authority to operate
this device under Part 15 regulations.
The shielded interface cable which is provided must be used with the equipment in order to comply with the limits for a digital device
pursuant to Subpart B of Part 15 of FCC Rules.
Customer Service: (800) 423-3537
www.bushnell.com
©2013 Bushnell Outdoor Products