Mitsubishi Electric M320 Instruction manual

A8AY.book 1 ページ
2013年9月12日 木曜日 午後6時58分
INVERTER
Plug-in option
FR-A8AY
INSTRUCTION MANUAL
PRE-OPERATION INSTRUCTIONS
Analog output function
1
INSTALLATION AND WIRING
2
Digital output function
PARAMETER LIST
3
ANALOG OUTPUT
4
DIGITAL OUTPUT
5
A8AY.book 3 ページ
2013年9月12日 木曜日 午後6時58分
Thank you for choosing this Mitsubishi inverter plug-in option.
This Instruction Manual provides handling information and precautions for use of the equipment. Incorrect handling might cause an unexpected
fault. Before using this inverter, always read this Instruction Manual carefully to use the equipment to its optimum performance.
Please forward this Instruction Manual to the end user.
Safety instructions
Do not attempt to install, operate, maintain or inspect the product until you have read through this Instruction Manual and appended
documents carefully and can use the equipment correctly. Do not use this product until you have a full knowledge of the equipment, safety
information and instructions. In this Instruction Manual, the safety instruction levels are classified into "WARNING" and "CAUTION".
Incorrect handling may cause hazardous conditions, resulting in death or severe injury.
Warning
Caution
The
Caution
Incorrect handling may cause hazardous conditions, resulting in medium or slight injury, or may cause only material
damage.
level may even lead to a serious consequence according to conditions. Both instruction levels must be followed
because these are important to personal safety.
 Electric Shock Prevention
Warning
 While the inverter power is ON, do not open the front cover or the wiring cover. Do not run the inverter with the front cover or the wiring cover removed. Otherwise
you may access the exposed high voltage terminals or the charging part of the circuitry and get an electric shock.
 Do not remove the inverter front cover even if the power supply is disconnected. The only exception for this would be when performing wiring and periodic
inspection. You may accidentally touch the charged inverter circuits and get an electric shock.
 Before wiring or inspection, LED indication of the inverter unit operation panel must be switched OFF. Any person who is involved in wiring or inspection shall wait
for at least 10 minutes after the power supply has been switched OFF and check that there is no residual voltage using a tester or the like. For a short time after the
power-OFF, a high voltage remains in the smoothing capacitor, and it is dangerous.
 Any person who is involved in wiring or inspection of this equipment shall be fully competent to do the work.
 The plug-in option must be installed before wiring. Otherwise you may get an electric shock or be injured.
 Do not touch the plug-in option or handle the cables with wet hands. Otherwise you may get an electric shock.
 Do not subject the cables to scratches, excessive stress, heavy loads or pinching. Otherwise you may get an electric shock.
 Injury Prevention
Caution




The voltage applied to each terminal must be the ones specified in the Instruction Manual. Otherwise a burst, damage, etc. may occur.
The cables must be connected to the correct terminals. Otherwise a burst, damage, etc. may occur.
The polarity (+ and -) must be correct. Otherwise a burst or damage may occur.
While power is ON or for some time after power OFF, do not touch the inverter as it will be extremely hot. Touching these devices may cause a burn.
3
A8AY.book 4 ページ
2013年9月12日 木曜日 午後6時58分
 Additional Instructions
The following instructions must be also followed. If the product is handled incorrectly, it may cause unexpected fault, an injury, or an electric
shock.
Caution
Transportation and mounting





Do not install or operate the plug-in option if it is damaged or has parts missing.
Do not stand or rest heavy objects on the product.
The mounting orientation must be correct.
Foreign conductive objects must be prevented from entering the inverter. That includes screws and metal fragments or other flammable substance such as oil.
If halogen-based materials (fluorine, chlorine, bromine, iodine, etc.) infiltrate into a Mitsubishi product, the product will be damaged. Halogen-based materials are
often included in fumigant, which is used to sterilize or disinfest wooden packages. When packaging, prevent residual fumigant components from being infiltrated
into Mitsubishi products, or use an alternative sterilization or disinfection method (heat disinfection, etc.) for packaging. Sterilization of disinfection of wooden
package should also be performed before packaging the product.
Trial run
 Before starting operation, each parameter must be confirmed and adjusted. A failure to do so may cause some machines to make unexpected motions.
Warning
Usage
 Do not modify the equipment.
 Do not perform parts removal which is not instructed in this manual. Doing so may lead to fault or damage of the product.
Caution
Usage
 When parameter clear or all parameter clear is performed, the required parameters must be set again before starting operations. Because all parameters return to
their initial values.
 Static electricity in your body must be discharged before you touch the product.
Maintenance, inspection and parts replacement
 Do not carry out a megger (insulation resistance) test.
Disposal
 The inverter must be treated as industrial waste.
General instruction
 Many of the diagrams and drawings in this Instruction Manual show the inverter without a cover or partially open for explanation. Never operate the inverter in this
manner. The cover must be reinstalled and the instructions in the Instruction Manual must be followed when operating the inverter.
4
A8AY.book 5 ページ
2013年9月12日 木曜日 午後6時58分
─ CONTENTS ─
1
PRE-OPERATION INSTRUCTIONS
1.1
Unpacking and checking the product.......................................................................................................7
1.1.1
1.2
1.3
2
Product confirmation....................................................................................................................................... 7
Component names .....................................................................................................................................8
Specifications .............................................................................................................................................9
INSTALLATION AND WIRING
2.1
2.2
2.3
7
10
Pre-installation instructions ....................................................................................................................10
Installation procedure ..............................................................................................................................10
Wiring ........................................................................................................................................................13
3
PARAMETER LIST
17
4
ANALOG OUTPUT
19
4.1
4.2
4.3
4.4
Connection diagram .................................................................................................................................19
Terminals...................................................................................................................................................20
Extended analog output function parameter list ...................................................................................21
Adjustment procedure .............................................................................................................................22
4.4.1
4.4.2
4.4.3
4.4.4
4.4.5
4.5
Analog output signal voltage/current switchover (Pr.309) setting................................................................. 22
Meter calibration ...........................................................................................................................................24
Setting output signals ...................................................................................................................................26
Analog meter voltage minus sign output selection (Pr.1019) ....................................................................... 26
Adjusting the analog signal (Pr.307, Pr.308, Pr.311, Pr.312)....................................................................... 27
Precautions ...............................................................................................................................................29
5
A8AY.book 6 ページ
5
5.1
5.2
5.3
6
2013年9月12日 木曜日 午後6時58分
DIGITAL OUTPUT
30
Terminals...................................................................................................................................................30
Digital output function parameter list.....................................................................................................31
Parameter setting .....................................................................................................................................31
A8AY.book 7 ページ
1
1.1
2013年9月12日 木曜日 午後6時58分
PRE-OPERATION INSTRUCTIONS
Unpacking and checking the product
Take the plug-in option out of the package, check the product name, and confirm that the product is as you ordered and intact.
This product is a plug-in option for the FR-A800 series.
1.1.1
Product confirmation
Check the enclosed items.
Plug-in option
.........................................................1
Mounting screw (M3  8 mm)
.........................2 (Refer to page 10.)
Spacer
....................2 (Refer to page 10.)
1
PRE-OPERATION INSTRUCTIONS
7
A8AY.book 8 ページ
1.2
2013年9月12日 木曜日 午後6時58分
Component names
Front view
(a)
Rear view
(d)
(c)
AM0
AM1
SE
Y0
Y1
Y2
Y3
(a)
(a)
Symbol
a
Y6
Y4
Y5
SE
(b)
AMC
(a)
Name
Refer to
page
Description
Mounting hole
Fixes the option to the inverter with screws, or installs spacers.
10
b
Terminal block
Connects the device to input the signal to the inverter, and the device to
receive the signal from the inverter.
13
c
Switch for manufacturer setting
Switch for manufacturer setting. Do not change the initial setting (
―
d
Connector
Connects to the option connector of the inverter.
8
PRE-OPERATION INSTRUCTIONS
).
10
A8AY.book 9 ページ
1.3
2013年9月12日 木曜日 午後6時58分
Specifications
 Analog output
Item
Voltage output
Current output
Output signal
0 to ±10 VDC max (across terminals AM0 to AMC)
Output resolution
3 mV
0 to 20 mADC (across terminals AM1 to AMC)
10 A
Applicable meter
DC voltmeter
Full-scale ±10 V (internal impedance: 10 k or more)
DC ammeter
Full-scale 20 mA (internal impedance: 300  or less)
Wiring length maximum 10 m
 Digital output
Open collector output specification: permissible load of 24 VDC 0.1 A
1
PRE-OPERATION INSTRUCTIONS
9
A8AY.book 10 ページ
2
2.1
2013年9月12日 木曜日 午後6時58分
INSTALLATION AND WIRING
Pre-installation instructions
Check that the inverter's input power and the control circuit power are both OFF.
Caution


Do not mount or remove the plug-in option while the input power is ON. Doing so may damage the inverter or plug-in option.
To avoid damage due to static electricity, static electricity in your body must be discharged before you touch the product.
2.2
Installation procedure
(1) Remove the inverter front cover. (Refer to Chapter 2 of the
Instruction Manual (Detailed) of the inverter for details on how to
remove the front cover.)
(2) For the two mounting holes (as shown in the next page) that will not
be tightened with mounting screws, insert spacers.
(3) Fit the connector of the plug-in option along the guide of the
connector on the inverter, and insert the plug-in option as far as it
goes.
(4) Fit the two locations, the left and right, of the plug-in option securely
to the inverter unit by screwing in the supplied mounting screws
(tightening torque 0.33 N·m to 0.40 N·m). If the screw holes do not
line up, the connector may not be inserted deep enough. Check the
connector.
10
INSTALLATION AND WIRING
Inverter side
option connector
Spacer
Spacer
A8AY.book 11 ページ
2013年9月12日 木曜日 午後6時58分
Spacer
Mounting screw
Connector 3
Spacer
Mounting screw
Spacer
Spacer
Connector 2
Spacer
Mounting screw
Connector 1
Spacer
Mounting screw
2
Insertion positions for screws and spacers
INSTALLATION AND WIRING
11
A8AY.book 12 ページ
2013年9月12日 木曜日 午後6時58分
NOTE
• When mounting/removing an option, hold the sides of the circuit board. Do not press on the parts on the circuit board.
Stress applied to the parts by pressing, etc. may cause a failure.
• Caution must be taken of mounting screws falling off when removing and mounting the plug-in option.
• Only one type of option per inverter may be used. When multiple options are mounted, priority is given to option
connectors 1, 2 and 3 on the inverter in this order, and options having a lower priority do not function. (For the
positions of the option connectors 1 to 3, refer to page 11.)
• When the inverter cannot recognize that the option unit is mounted due to improper installation, etc., the protective
function (E.1 to E.3) is displayed. A different indication will appear according to the mounted position (option connector
1 to 3).
Mounted position
Fault indication
Option connector 1
Option connector 2
Option connector 3
• When removing the plug-in option, remove the two screws on the left and right, then pull it straight out. Pressure
applied to the connector and to the option board may break the option.
12
INSTALLATION AND WIRING
A8AY.book 13 ページ
2.3
2013年9月12日 木曜日 午後6時58分
Wiring
(1) For the wiring, strip off the sheath of a cable, and use it with a blade terminal. For a single wire, strip off the sheath of the
wire and apply directly. Insert the blade terminal or the single wire into a socket of the terminal.
Strip off the sheath for the below length. If the length of the sheath peeled is too long, a short circuit may occur with neighboring
wires. If the length is too short, wires might come off.
Wire the stripped cable after twisting it to prevent it from becoming loose. In addition, do not solder it.
Cable sheath stripping length
Crimp the blade terminal.
Insert wires to a blade terminal, and check that the wires come out for about 0 to 0.5 mm.
Check the condition of the blade terminal after crimping. Do not use a blade terminal of which the crimping is inappropriate, or
the face is damaged.
Unstranded
wires
ire
ve
ee
Sl
W
2
m
.5m
o0
0t
Damaged
Crumpled tip
Wires are not inserted
into the sleeve
Caution

After wiring, wire offcuts must not be left in the inverter. They may cause a fault, failure or malfunction.
INSTALLATION AND WIRING
13
A8AY.book 14 ページ
2013年9月12日 木曜日 午後6時58分
Blade terminals commercially available (as of February 2012. The product may be changed without notice.)
Cable gauge
(mm2)
Blade terminal model
With
insulation sleeve
Without
insulation sleeve
For UL wire 
0.3
AI 0,5-10WH
—
—
0.5
AI 0,5-10WH
—
AI 0,5-10WH-GB
0.75
AI 0,75-10GY
A 0,75-10
AI 0,75-10GY-GB
1
AI 1-10RD
A 1-10
AI 1-10RD/1000GB
1.25, 1.5
AI 1,5-10BK
A 1,5-10
—
0.75
(for two cables)
AI-TWIN 2  0,75-10GY
—
—

14
Phoenix Contact
Co., Ltd.
Crimping tool
name
CRIMPFOX 6
A blade terminal with an insulation sleeve compatible with the MTW wire which has a thick wire insulation.
Cable gauge (mm2)
0.3 to 0.75
Manufacturer
Blade terminal
product number
BT 0.75-11
INSTALLATION AND WIRING
Insulation
product number
VC 0.75
Manufacturer
NICHIFU Co.,Ltd.
Crimping tool
product number
NH 67
A8AY.book 15 ページ
2013年9月12日 木曜日 午後6時58分
(2) Insert the cable into a socket.
When using a single wire or stranded wires without a blade terminal, push the
open/close button all the way down with a flathead screwdriver, and insert the
wire.
Open/close button
Flathead screwdriver
• Wire removal
Pull the wire while pushing the open/close button all the way down firmly with a flathead screwdriver.
Open/close button
2
Flathead screwdriver
INSTALLATION AND WIRING
15
A8AY.book 16 ページ
2013年9月12日 木曜日 午後6時58分
NOTE
• When using stranded wires without a blade terminal, twist enough to avoid short circuit with a nearby terminals or
wires.
• Pulling out the wire forcefully without pushing the open/close button all the way down may damage the terminal block.
• Use a small flathead screwdriver (tip thickness: 0.4 mm/tip width: 2.5 mm). If a flathead screwdriver with a narrow tip
is used, terminal block may be damaged.
Commercially available product (as of February 2012. The product may be changed without notice.)
Name
Driver
Model
SZF 0- 0,4  2,5
Manufacturer
Phoenix Contact Co., Ltd.
• Place the flathead screwdriver vertical to the open/close button. In case the blade tip slips, it may cause an inverter
damage or injury.
• When wiring cables to the inverter's RS-485 terminals while a plug-in option is mounted, take caution not to let the
cables touch the circuit board of the option or of the inverter. Otherwise, electromagnetic noises may cause
malfunctions.
16
INSTALLATION AND WIRING
A8AY.book 17 ページ
3
2013年9月12日 木曜日 午後6時58分
PARAMETER LIST
When the FR-A8AY is mounted on the inverter, the following parameters are extended.
Extended analog output
Pr.
Pr.
group
Refer to page
Minimum
setting
increments
Setting range
Initial
value
306
M303
Analog output signal selection
1 to 3, 5 to 14, 17, 18, 21, 24,
32 to 34, 50, 52 to 54, 61, 62,
67, 70, 87 to 97
1
2
307
M340
Setting for zero analog output
0 to 100%
0.1%
0%
308
M341
Setting for maximum analog
output
0 to 100%
0.1%
100%
309
M342
Analog output signal voltage/
current switchover
0, 1, 10, 11
1
0
310
M343
Analog meter voltage output
selection
1 to 3, 5 to 14, 17, 18, 21, 24,
32 to 34, 50, 52 to 54, 61, 62,
67, 70, 87 to 97
1
2
311
M344
Setting for zero analog meter
voltage output
0 to 100%
0.1%
0%
312
M345
Setting for maximum analog
meter voltage output
0 to 100%
0.1%
100%
323
M346
AM0 0V adjustment
900 to 1100%
1%
1000%
324
M347
AM1 0mA adjustment
900 to 1100%
1%
1000%
418
M432
Extension output terminal filter
5 to 50 ms, 9999
1 ms
9999
Refer to
page
19 and later
PARAMETER LIST
3
17
A8AY.book 18 ページ
Digital output
Extended analog output
Pr.
2013年9月12日 木曜日 午後6時58分
Pr.
group
Refer to page
Minimum
setting
increments
Setting range
Initial
value
C0
(900)
M310
FM/CA terminal calibration
—
—
—
C1
(901)
M320
AM terminal calibration
—
—
—
1019
M305
Analog meter voltage minus sign
output selection
313
M410
DO0 output selection
314
M411
DO1 output selection
315
M412
DO2 output selection
316
M413
DO3 output selection
317
M414
DO4 output selection
318
M415
DO5 output selection
319
M416
DO6 output selection
18
Refer to
page
19 and later
PARAMETER LIST
0, 1
1
0
0 to 8, 10 to 20, 22,
25 to 28, 30 to 36, 38, 39,
41 to 54, 56, 57, 61, 63, 64,
68, 70, 84 to 99, 100 to 108,
110 to 116, 120, 122,
125 to 128, 130 to 136, 138,
139, 141 to 154, 156, 157,
161, 163, 164, 168, 170,
184 to 199, 200 to 205,
300 to 305, 9999
1
9999
30 and later
A8AY.book 19 ページ
4
4.1
2013年9月12日 木曜日 午後6時58分
ANALOG OUTPUT
Connection diagram
By setting Pr.306 to Pr.312, analog signals such as the output frequency and output current can be output from the voltage
output terminal (AM0) and current output terminal (AM1).
Connect the voltmeter or ammeter as shown below:
MCCB
Inverter
Power
supply
(Voltmeter)
Motor
M
+ 0 to ±10 VDC
FR-A8AY
-
(Ammeter)
AM0
AM1
AMC
+
-
0 to 20 mADC
NOTE
• The wiring length for the voltmeter/ammeter should be within 10 m.
4
ANALOG OUTPUT
19
A8AY.book 20 ページ
4.2
2013年9月12日 木曜日 午後6時58分
Terminals
∗1
SE
Y0
Y1
Y2
Y3
AM0
AM1
Terminal
symbol
Voltage output terminal
Connects the DC voltmeter (10 VDC).
AM1
Current output terminal
Connects the DC ammeter (20 mADC).
AMC
Common terminal
Common terminal for AM0 and AM1.
Used for digital output function. (Refer to page 30.)
Y6
Y4
Y5
SE
AMC
SE
20
ANALOG OUTPUT
Description
AM0
Y0 to Y6
∗1
Terminal name

Empty terminal. Do not use.
A8AY.book 21 ページ
4.3
2013年9月12日 木曜日 午後6時58分
Extended analog output function parameter list
Parameter
number
Name
Minimum
increments
Setting range
Initial
value
Analog output signal selection
1 to 3, 5 to 14, 17, 18, 21, 24, 32 to 34, 50,
52 to 54, 61, 62, 67, 70, 87 to 97
307
Setting for zero analog output
0 to 100%
0.1%
0%
308
Setting for maximum analog output
0 to 100%
0.1%
100%
309
Analog output signal voltage/current
switchover
0, 1, 10, 11
1
0
310
Analog meter voltage output selection
1 to 3, 5 to 14, 17, 18, 21, 24, 32 to 34, 50,
52 to 54, 61, 62, 67, 70, 87 to 97
1
2
311
Setting for zero analog meter voltage output
0 to 100%
0.1%
0%
312
Setting for maximum analog meter voltage
output
0 to 100%
0.1%
100%
323
AM0 0V adjustment
900 to 1100%
1%
1000%
324
AM1 0mA adjustment
900 to 1100%
1%
1000%
C0 (900)
FM/CA terminal calibration
—
—
—
C1 (901)
AM terminal calibration
—
—
—
1019
Analog meter voltage minus sign output
selection
0, 1
1
0
306
1
2
NOTE
• Pr.306, Pr.310 can be written even when the inverter is operating.
4
ANALOG OUTPUT
21
A8AY.book 22 ページ
4.4
2013年9月12日 木曜日 午後6時58分
Adjustment procedure
4.4.1
Analog output signal voltage/current switchover (Pr.309) setting
Use Pr.309 Analog output signal voltage/current switchover to select whether to send the same signal from terminal AM0
(voltage output) and terminal AM1 (current output), or to send the signals separately.
Pr.309
setting
value
Description
Terminal
AM0
0
(Initial value)
10
Outputs the same selection signal from both the
voltage output terminal (AM0) and the current
output terminal (AM1).
The signal that set in Pr.306 Analog output
signal selection is enabled. (The Pr.310 setting
is disabled.)
AM1
AM0
AM1
22
ANALOG OUTPUT
Parameter setting
Calibration
parameter
Pr.306: Selects the output signal.
Pr.307: Output signal value when analog
output is zero.
Pr.308: Output signal value when analog
Pr.323
output is at maximum.
Pr.324
Pr.306: Selects the output signal.
C1 (Pr.901)
Pr.307: Analog output value when output
signal is zero.
Pr.308: Analog output value when output
signal is at maximum.
A8AY.book 23 ページ
Pr.309
setting
value
2013年9月12日 木曜日 午後6時58分
Description
Terminal
Parameter setting
Calibration
parameter
AM0
Pr.310: Selects the output signal.
Pr.311: Output signal value when analog
Pr.323
output is zero.
C0 (Pr.900)
Pr.312: Output signal value when analog
output is at maximum.
AM1
Pr.306: Selects the output signal.
Pr.307: Output signal value when analog
Pr.324
output is zero.
C1 (Pr.901)
Pr.308: Output signal value when analog
output is at maximum.
AM0
Pr.310: Selects the output signal.
Pr.311: Analog output value when output
Pr.323
signal is zero.
C0 (Pr.900)
Pr.312: Analog output value when output
signal is at maximum.
AM1
Pr.306: Selects the output signal.
Pr.307: Analog output value when output
Pr.324
signal is zero.
C1 (Pr.901)
Pr.308: Analog output value when output
signal is at maximum.
1
Outputs separate selection signals from the
voltage output terminal (AM0) and the current
output terminal (AM1).
11
NOTE
• "Analog output" means the voltage (0 to 10 V) and current (0 to 20 mA) output from terminals AM0 and AM1; while
"output signal" indicates the monitor signal (refer to page 26) set in parameters Pr.306 and Pr.310.
4
ANALOG OUTPUT
23
A8AY.book 24 ページ
4.4.2
2013年9月12日 木曜日 午後6時58分
Meter calibration
(1) Outputting the same signal from terminals AM0 and AM1 (Pr.309 = "0 or 10")
START
Connect a DC voltmeter (or DC ammeter) across
terminals AM0 (or terminal AM1) and AMC.
Use Pr. 323 (Pr. 324) to calibrate the meter
when the voltage (current) input is 0.
Set "21" (reference voltage output) in Pr. 306.
Use Pr. 901 to perform adjustment, then set.
At this time, check that the polarity is correct
If the meter needle does not point to 0 when voltage or current input is 0,
use Pr. 323 AM0: 0 V adjustment or Pr. 324 AM1: 0 mA adjustment to
calibrate the meter
At this time, the following analog signal is actually output and deflects the meter.
<across terminals AM0-AMC>
Maximum output voltage set previously (factory setting: 10 VDC)
<across terminals AM1-AMC>
Maximum output current set previously (factory setting: 20 mADC)
After making adjustment with
press
to deflect the meter to full-scale,
to set.
END
In Pr. 306, set the types of the signals to be output. (Refer to page 26.)
NOTE
• If calibration is performed without setting Pr.306 = "21 (reference voltage output)", the terminal AM of the inverter is
calibrated. To calibrate the extended analog output, always set to "21".
• When the plug-in option used was remounted on another inverter, use Pr.323 and Pr.324 to calibrate again.
24
ANALOG OUTPUT
A8AY.book 25 ページ
2013年9月12日 木曜日 午後6時58分
(2) Outputting separate signals from terminals AM0 and AM1 (Pr.309 = "1 or 11")
START
Connect a DC voltmeter (or DC ammeter)
At this time, check that the polarity is correct
across terminals AM0 (or terminal AM1) and AMC.
Use Pr. 323 (or Pr. 324) to calibrate the meter
when the voltage (current) input is 0.
If the meter needle does not point to 0 when voltage or current input is 0,
use Pr. 323 AM0 for 0 V adjustment or Pr. 324 AM1 for 0 mA adjustment of
the meter
Set "21" (reference voltage output) in Pr.306 and
Pr. 310.
At this time, the following analog signal is actually output and deflects the meter.
<across terminals AM0-AMC>
Maximum output voltage set previously (factory setting: 10 VDC)
<across terminals AM1-AMC>
Maximum output current set previously (factory setting: 20 mADC)
Terminal AM0
Terminal AM1
Use Pr. 901 to set
Use Pr. 900 to set
After making adjustment with
press
to deflect the meter to full-scale,
to set.
END
In Pr. 306 and Pr. 310, set the types of the signals to be output. (Refer to page 26.)
NOTE
• If calibration is performed without setting "21 (reference voltage output)" in Pr.306 or Pr.310, the terminal FM, CA, or
AM of the inverter is calibrated. To calibrate the extended analog output, always set to "21".
• When the plug-in option used was remounted on another inverter, use Pr.323 and Pr.324 to calibrate again.
4
ANALOG OUTPUT
25
A8AY.book 26 ページ
2013年9月12日 木曜日 午後6時58分
4.4.3
Setting output signals
4.4.4
Analog meter voltage minus sign output selection (Pr.1019)
Set the output signals to be monitored. Set Pr.306 to output the same signal from terminals AM0 and AM1, and Pr.306 and
Pr.310 to output different signals. The AM0 terminal can be used for negative output (from -10 VDC to +10 VDC). The settings
of Pr.306 and Pr.310 are the same as those of Pr.54 FM/CA terminal function selection and Pr.158 AM terminal function
selection. For the details of Pr.54 and Pr.158, refer to the Instruction Manual (Detailed) of the inverter.
The output from the terminal AM0 (analog voltage output) can be displayed with minus signs on the monitor. For the monitored
items that can have minus signs, refer to the description of Pr.54 FM/CA terminal function selection and Pr.158 AM terminal
function selection in the Instruction Manual (Detailed) of the inverter.
Pr.1019 setting
Minus sign output from terminal AM0
0 (initial value)
Output without minus sign (positive values only)
1
Output with minus sign.
NOTE
• When terminal AM0 (analog voltage output) is “output with a minus sign”, the output will be within the -10V DC to +10V
DC range.
Connect the meter with which output level is matched.
• Parameter unit (FR-PU07) displays only positive values.
• When the remote output 1 to 4 is set to the terminal AM0 (Pr.306 = "87 to 90"), regardless of the Pr.1019 setting,
minus outputs can be made.
26
ANALOG OUTPUT
A8AY.book 27 ページ
4.4.5
2013年9月12日 木曜日 午後6時58分
Adjusting the analog signal (Pr.307, Pr.308, Pr.311, Pr.312)
Use Pr. 307 or Pr. 311 to set the values at zero analog output (meter points 0) and Pr. 308 or Pr. 312 at maximum analog
output (full scale).
When outputting the same signal from terminals AM0 and AM1, use Pr.307 to set the value at zero analog output and Pr.308 at
maximum analog output. When outputting separate signals from terminals AM0 and AM1, use Pr.307 (for terminal AM1) and
Pr.311 (for terminal AM0) to set the value at zero analog output, and Pr.308 (for terminal AM1) and Pr.312 (for terminal AM0) at
maximum analog output. (Refer to page 22.)
Pr.309 = "0, 1"
Pr.1019 = "0" (output without minus sign)
Analog output
0
Analog output
Output signal value
(Pr. 308 or Pr. 312)
for maximum analog output
Output signal value
(Pr. 308 or Pr. 312)
for maximum analog output
Current (AM1): 20 mA
Voltage (AM0): 10 V
Current (AM1):
20 mA
Voltage (AM0):
10 V
-100%
Pr.1019 = "1" (output with minus sign)
100%
Output signal
value
Output signal value
(Pr. 307 or Pr. 311)
for zero output signal
-100%
100%
0
Output signal
value
Output signal value
(Pr. 307 or Pr. 311)
for zero output signal
-10V
NOTE
• When Pr.307  Pr.308 and Pr.311  Pr.312, the output values from the terminals AM0 and AM1 will always be zero.
ANALOG OUTPUT
27
4
A8AY.book 28 ページ
2013年9月12日 木曜日 午後6時58分
Pr.309 = "10, 11"
Pr.1019 = "0" (output without minus sign)
Pr.1019 = "1" (output with minus sign)
Analog output
Limited at 10 V
Analog output
Limited at 10 V
Current (AM1): 20 mA
Voltage (AM0): 10 V
Current (AM1): 20 mA
Voltage (AM0): 10 V
Limited at 10 V
Output signal value
(Pr. 307 or Pr. 311)
for zero output signal
-100%
0
Output signal value
(Pr. 307 or Pr. 311)
for zero analog output
100%
Output signal
value
-100%
0
Analog output value
(Pr. 308 or Pr. 312) for
maximum output signal
100%
Output signal
value
Analog output value
(Pr. 308 or Pr. 312) for
maximum output signal
-10V
Limited at -10 V
NOTE
• When Pr.307 = Pr.308 and Pr.311 = Pr.312, the output values from the terminals AM0 and AM1 will always be the
values that are set in the parameters.
28
ANALOG OUTPUT
A8AY.book 29 ページ
4.5
2013年9月12日 木曜日 午後6時58分
Precautions
• When using a voltmeter with a lower internal impedance or an ammeter having a greater internal impedance than the value
indicated in the specifications (Refer to page 9), the indicator may not go to full-scale, making it unable to calibrate in some
cases.
• When calibrating a meter with small full scale, first adjust the outputs from the terminals AM0 and AM1 accordingly, then
connect the meter.
Caution

This product is initially set to provide the full-scale output of 10 VDC and 20 mADC. Voltmeters (7 VDC or less) or ammeters (14 mADC or less) with a
small full-scale value may accidentally be damaged during calibration. Use caution.
• When calibrating the meter using Pr.323, Pr.324, C0 (Pr.900), and C1 (Pr.901) while Pr.309 = "10 or 11", set "0%" in Pr.307
or Pr.311, and "100%" in Pr.308 or Pr.312 to prevent calibration value deviation.
• All the outputs are shut off when a protective function (E.1 to E.3) is activated.
4
ANALOG OUTPUT
29
A8AY.book 30 ページ
5
5.1
2013年9月12日 木曜日 午後6時58分
DIGITAL OUTPUT
Terminals
Use Pr.313 to Pr.319 to output inverter signals (RUN, SU, etc.) as open collector outputs.
Terminal
symbol
Terminal name
Y0
Assigns the function using Pr.313.
Y1
Assigns the function using Pr.314.
SE
Y0
Y1
Y2
Y3
AM0
AM1
Y2
∗1
Y3
Assigns the function using Pr.317.
Assigns the function using Pr.318.
Y6
Assigns the function using Pr.319.
Y6
Y4
Y5
SE
AMC
30
DIGITAL OUTPUT
Common terminal
Common terminals for the terminals Y0 to Y6.
Isolated from the terminal SE of the inverter
AM0
AMC
Empty terminal. Do not use.
Assigns the function using Pr.316.
Y5
AM1

Assigns the function using Pr.315.
Digital output
terminal
Y4
SE
∗1
Description
Used for analog output function. (Refer to page 19.)
A8AY.book 31 ページ
5.2
2013年9月12日 木曜日 午後6時58分
Digital output function parameter list
Parameter number
Name
Initial value
313
DO0 output selection
9999
314
DO1 output selection
9999
315
DO2 output selection
9999
316
DO3 output selection
9999
317
DO4 output selection
9999
318
DO5 output selection
9999
319
DO6 output selection
9999
418
Extension output terminal filter
9999
5.3
Setting range
0 to 8, 10 to 20, 22, 25 to 28, 30 to 36, 38,
39, 41 to 54, 56, 57, 61, 63, 64, 68, 70,
84 to 99, 100 to 108, 110 to 116, 120, 122,
125 to 128, 130 to 136, 138, 139,
141 to 154, 156, 157, 161, 163, 164, 168,
170, 184 to 199, 200 to 205, 300 to 305,
9999
5 to 50 ms, 9999
Parameter setting
 Setting output signals
Use Pr.313 to Pr.319 to assign signals to the terminals DO0 to DO6. The settings of Pr.313 to Pr.319 are the same as those of
Pr.190 to Pr.196 (output terminal function selection). For the details of Pr.190 to Pr.196, refer to the Instruction Manual
(Detailed) of the inverter.
NOTE
• The same function can be set to two output terminals or more.
DIGITAL OUTPUT
31
5
A8AY.book 32 ページ
2013年9月12日 木曜日 午後6時58分
 Adjusting the output terminal response level (Pr.418)
Output frequency
• The response level of the output terminals can be delayed in a range of 5 to 50 ms. (Operation example for the RUN signal.)
Time
RUN
Pr.418 = 9999
RUN
Pr.418 ≠ 9999
OFF
ON
ON
Pr.418
OFF
Pr.418
NOTE
• The response level is not adjusted while Pr.418 = "9999".
• When Pr.157 OL signal output timer is set for the Overload warning (OL) signal output, the OL signal is output when
the set time of (Pr.157 + Pr.418) elapses.
32
DIGITAL OUTPUT
A8AY.book 33 ページ
2013年9月12日 木曜日 午後6時58分
MEMO
33
A8AY.book 34 ページ
2013年9月12日 木曜日 午後6時58分
REVISIONS
* The manual number is given on the bottom left of the back cover.
Print date
Aug. 2013
34
* Manual number
IB(NA)-0600497ENG-A
Revision
First edition
A8AY.book 36 ページ
2013年9月12日 木曜日 午後6時58分
INVERTER
HEAD OFFICE: TOKYO BUILDING 2-7-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
IB(NA)-0600497ENG-A(1308) MEE
Printed in Japan
Specifications subject to change without notice.