MULTIQUIP MVC-88VGEW Specifications

OPERATION & PARTS MANUAL
SERIES
MODEL MVC-88VGE/VGEW
ONE-WAY PLATE COMPACTOR
(ROBIN GASOLINE ENGINE)
Revision #0 (06/07/06)
To find the latest revision of this
publication, visit our website at:
www.multiquip.com
THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
MVC-88VGE/VGEW PLATE COMPACTOR — PROPOSITION 65 WARNING
l
PAGE 2 — MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06)
NOTE PAGE
MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06) — PAGE 3
MVC-88VGE/VGEW PLATE COMPACTOR — TABLE OF CONTENTS
Multiquip — MVC-88VGE/VGEW Robin EX170D54011 ENGINE
Air Cleaner Assembly.........................................38-39
Plate Compactor
Proposition 65 Warning ............................................. 2
Table Of Contents ..................................................... 4
Parts Ordering Procedures ....................................... 5
Safety Message Alert Symbols .............................. 6-7
Rules For Safe Operation ...................................... 8-9
Operation and Safety Decals .................................. 10
Specifications (Compactor/Engine) ........................ 11
General Information ................................................ 12
Components (Compactor) ...................................... 13
Components (Engine) ............................................. 14
Inspection ........................................................... 15-16
Initial Start-Up .................................................... 17-18
Operation ................................................................ 18
Maintenance ...................................................... 19-21
Preparation For Long Term Storage ....................... 22
Troubleshooting (Engine) ................................... 23-24
Troubleshooting (Plate Compactor) ........................ 24
Explanation Of Codes In Remarks Column ............ 26
Suggested Spare Parts ........................................... 27
Camshaft Assembly ...........................................40-41
Carburetor Assembly .........................................42-43
Crankcase Assembly .........................................44-45
Crankshaft and Piston Assembly .......................46-47
Cylinder Head Assembly ....................................48-49
Fuel Tank Assembly ...........................................50-51
Governor Assembly ...........................................52-53
Ignition Coil/Flywheel Assembly.........................54-55
Muffler Assembly ...............................................56-57
Recoil Starter Assembly.....................................58-59
Tool Kit Assembly ...............................................60-61
Terms and Conditions Of Sale — Parts .................. 62
Component Drawings
Nameplate and Decals....................................... 28-29
Body Assembly .................................................. 30-31
Vibrator Assembly .............................................. 32-33
Sprinkler Assembly (Option) .............................. 34-35
Transport Wheel Assembly (Option) .................. 36-37
l
NOTE
Specification and part number
are subject to change without
notice.
PAGE 4 — MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06)
www.multiquip.com
Effective: June 1st, 2005
PARTS ORDERING PROCEDURES
Ordering parts has never been easier!
Choose from three easy options:
Best Deal!
Order via Internet (Dealers Only):
If you have an MQ Account, to obtain a
Username and Password, E-mail us at:
parts@multiquip.com.
Order parts on-line using Multiquip’s SmartEquip website!
■ View Parts Diagrams
■ Order Parts
■ Print Specification Information
To obtain an MQ Account, contact your
District Sales Manager for more information.
Use the internet and qualify for a 5% Discount
on Standard orders for all orders which include
complete part numbers.*
Go to www.multiquip.com and click on
Order Parts to log in and save!
Note: Discounts Are Subject To Change
Fax your order in and qualify for a 3% Discount
on Standard orders for all orders which include
complete part numbers.*
Order via Fax (Dealers Only):
All customers are welcome to order parts via Fax.
Domestic (US) Customers dial:
1-800-6-PARTS-7 (800-672-7877)
Note: Discounts Are Subject To Change
Order via Phone: Domestic (US) Dealers Call:
1-800-427-1244
Non-Dealer Customers:
Contact your local Multiquip Dealer for
parts or call 800-427-1244 for help in
locating a dealer near you.
International Customers should contact
their local Multiquip Representatives for
Parts Ordering information.
When ordering parts, please supply:
❒
❒
❒
❒
❒
❒
Dealer Account Number
Dealer Name and Address
Shipping Address (if different than billing address)
Return Fax Number
Applicable Model Number
Quantity, Part Number and Description of Each Part
NOTE
❒
Specify Preferred Method of Shipment:
✓ Fed Ex/UPS
✓ DHL
✓ Truck
■ Priority One
■ Ground
■ Next Day
■ Second/Third Day
Unless otherwise indicated by customer, all orders are treated as Standard Orders and will ship
within 24 hours. We will make every effort to ship Air Shipments the same day the order is received,
if received prior to 2PM PST. Stock Orders must be noted on fax or web order form.
WE ACCEPT ALL MAJOR CREDIT CARDS!
MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06) — PAGE 5
MVC-88VGE/VGEW PLATE COMPACTOR — SAFETY MESSAGE ALERT SYMBOLS
FOR YOUR SAFETY AND THE SAFETY OF OTHERS!
HAZARD SYMBOLS
Safety precautions should be followed
at all times when operating this
equipment. Failure to read and
understand the Safety Messages and
Operating Instructions could result in
injury to yourself and others.
Potential hazards associated with the operation of an
MVC-88VGE/VGEW Plate Compactor will be referenced
with Hazard Symbols which appear throughout this manual,
Lethal Exhaust Gases
and will be referenced in conjunction with Safety Message
Alert Symbols.
WARNING
NOTE
This manual has been developed to
provide complete instructions for the
safe and efficient operation of the MQ
Mikasa MVC-88VGE/VGEW Plate
Compactor . Refer to the engine
manufacturer's instructions for data
relative to its safe operation.
Before using this plate compactor, ensure that the
operating individual has read and understood all
instructions in this manual.
SAFETY MESSAGE ALERT SYMBOLS
The three (3) Safety Messages shown below will inform you
about potential hazards that could injure you or others. The
Safety Messages specifically address the level of exposure to
the operator, and are preceded by one of three words: DANGER,
DANGER
You WILL be KILLED or SERIOUSLY INJURED
if you DO NOT follow these directions.
WARNING
Engine exhaust gases contain
poisonous carbon monoxide. This gas
is colorless and odorless, and can
cause death if inhaled. NEVER operate
this equipment in a confined area or
enclosed structure that does not provide
ample free flow air.
WARNING
You CAN be KILLED or SERIOUSLY INJURED if
you DO NOT follow these directions.
CAUTI
CAUTION
You CAN be INJURED if you DO NOT follow
these directions.
Explosive Fuel Hazards
Gasoline is extremely flammable, and
its vapors can cause an explosion if
ignited. DO NOT start the engine near
spilled fuel or combustible fluids.
DO NOT fill the fuel tank while the engine is running or
hot. DO NOT overfill tank, since spilled fuel could ignite if
it comes into contact with hot engine parts or sparks from
the ignition system. Store fuel in approved containers, in
well-ventilated areas and away from sparks and flames.
WARNING
l
Lethal Exhaust Gas Hazards
Burn Hazards
Engine components can generate extreme
heat. To prevent burns, DO NOT touch
these areas while the engine is running or
immediately after operation. Never operate
the engine with heat shields or heat guards
removed.
WARNING
Respiratory Hazards
ALWAYS wear approved respiratory
protection when required.
PAGE 6 — MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06)
MVC-88VGE/VGEW PLATE COMPACTOR — SAFETY MESSAGE ALERT SYMBOLS
CAUTION
Rotating Parts Hazards
NEVER operate equipment with covers,
or guards removed. Keep fingers, hands,
hair and clothing away from all moving
parts to prevent injury.
CAUTION
CAUTION
Equipment Damage
Hazards
Other important messages are provided throughout this
manual to help prevent damage to your equipment, other
property, or the surrounding environment.
Accidental Starting Hazards
ALWAYS place the engine ON/OFF switch
in the OFF position, when the plate
compactor is not in use.
CAUTION
Eye and Hearing Hazards
ALWAYS wear approved eye and hearing
protection.
MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06) — PAGE 7
MVC-88VGE/VGEW PLATE COMPACTOR — RULES FOR SAFE OPERATION
WARNING - Read This Manual
Failure to follow instructions in this manual may lead to
Serious Injury or even Death. This equipment is to be
operated by trained and qualified personnel only! This
equipment is for industrial use only.
The following safety guidelines should always be used
when operating the Mikasa MVC-88VGE/VGEW Plate
Compactor.
Safety:
■ DO NOT operate or service this
equipment before reading this entire
manual.
■ This equipment should not be
operated by persons under 18 years of age.
■ NEVER operate this equipment without proper protective
clothing, shatterproof glasses, steel-toed boots and other
protective devices required by the job.
■ NEVER operate this equipment when not
feeling well due to fatigue, illness or taking
medicine.
■ NEVER operate the plate compactor under the influence
or drugs or alcohol.
■ NEVER disconnect any "emergency or safety devices".
l for operator safety.
These devices are intended
Disconnection of these devices can cause severe injury,
bodily harm or even death! Disconnection of any of these
devices will void all warranties.
■ NEVER use accessories or attachments, which are not
recommended by Multiquip for this equipment. Damage
to the equipment and/or injury to user may result.
■ Manufacturer does not assume responsibility for any
accident due to equipment modifications. Unauthorized
equipment modification will void all warranties.
■ Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
■ NEVER touch the hot exhaust manifold,
muffler or cylinder. Allow these parts to
cool before servicing engine or
generator.
■ High Temperatures – Allow the engine
to cool before adding fuel or performing
service and maintenance functions.
Contact with hot! components can cause serious burns.
■ The engine of this plate compactor requires an adequate
free flow of cooling air. NEVER operate the plate
compactor in any enclosed or narrow area where free
flow of the air is restricted. If the air flow is restricted it
will cause serious damage to
the plate compactor or engine
and may cause injury to people
and property. Remember the
compactor's engine gives off
DEADLY gases.
■ ALWAYS refuel in a well-ventilated area, away from
sparks and open flames.
■ ALWAYS use extreme caution when
working with flammable liquids. When
refueling, stop the engine and allow it to
cool. DO NOT smoke around or near the
machine. Fire or explosion could result
from fuel vapors, or if fuel is spilled on a
hot engine.
■ NEVER operate the plate compactor in
an explosive atmosphere or near
combustible materials. An explosion or
fire could result causing severe bodily
harm or even death.
■ Topping-off to filler port is dangerous, as it tends to spill
fuel.
■ ALWAYS store the plate compactor in a clean, dry
location out of the reach of children.
■ NEVER run engine without air cleaner. Severe engine
damage may occur.
■ NEVER leave the plate compactor unattended, turn off
engine.
■ CAUTION must always be observed while servicing this
plate compactor. Rotating parts can cause injury if
contacted.
■ ALWAYS check all the bolts on the plate compactor for
tightness.
PAGE 8 — MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06)
MVC-88VGE/VGEW PLATE COMPACTOR — RULES FOR SAFE OPERATION
Loading and Unloading (Crane):
■ Before lifting, make sure that machine parts (hook and
vibration insulator) are not damaged and screws are not
loosened or lost.
■ ALWAYS make sure crane or lifting device has been
properly secured to the hook of guard frame on compactor.
■ NEVER lift the machine while the engine is running.
■ Use adequate lifting cable (wire or rope) of sufficient
strength.
■ Use one point suspension hook and lift straight upwards.
■ NEVER allow any person or animal to stand underneath
the machine while lifting.
■ Try not to lift machine to unnecessary heights.
Maintenance Safety:
■ NEVER lubricate components or attempt service on a
running machine.
■ ALWAYS allow the machine a proper amount of time to
cool before servicing.
■ Keep the machinery in proper running condition.
■ Fix damage to the machine immediately and always
replace broken parts.
■ Dispose of hazardous waste properly. Examples of
potentially hazardous waste are used motor oil, fuel and
fuel filters.
■ DO NOT use food or plastic containers to dispose of
hazardous waste.
■ DO NOT pour waste, oil or fuel directly onto the ground,
down a drain or into any water source.
Transporting
■ ALWAYS shutdown engine before transporting.
■ Tighten fuel tank cap securely and close fuel cock to Emergencies:
prevent fuel from spilling.
■ ALWAYS know the location of the
■ Drain fuel when transporting compactor over long
nearest fire extinguisher.
distances or bad roads.
■ ALWAYS know the location of the
■ ALWAYS tie down the compactor during transportation
nearest first aid kit.
by securing the compactor's guard frame with rope.
■ In emergencies always know the location
of the nearest phone or keep a phone on the job site.
Also know the phone numbers of the nearest
ambulance , doctor and fire department . This
information will be invaluable in the case of an
emergency.
MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06) — PAGE 9
MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION AND SAFETY DECALS
Machine Safety Decals
The MVC-88VGE/VGEW Plate Compactor is equipped with a number of safety decals. These decals are provided for operator
safety and maintenance information. The illustration below shows these decals as they appear on the machine. Should any of these
decals become unreadable, replacements can be obtained from your dealer.
l
PAGE 10 — MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06)
MVC-88VGE/VGEW PLATE COMPACTOR — SPECIFICATIONS
TABLE 1. Specifications (Compactor)
Models
MVC-88VGE/MVC-88VGEW
Centrifugal Force
3,370 lbs. (1,530 kg)
Number of Vibrations
6,000 vibrations/min
Traveling Speed
72 ft./min (22 meters/min)
Plate Size (LxW)
19.7 x 20.7 in.
(.500 x .525 mm)
Operating Weight (VGE)
Operating Weight (VGEW)
Fuel Tank Capacity
Water Tank Capacity
(VGEW Model Only)
Max. Area Of Compaction
196 lbs. (89.0 kg.)
217 lbs. ( 98.5 kg.)
3.8 qt. (3.6 liters)
13.7 qt. (13.0 liters)
7500 sq. ft./hr.
Table 2. Specifications (Engine)
Engine Make
ROBIN (FUJI HEAVY INDUSTRIES)
Engine Model
EX170D54011
Engine Type
OHV Gasoline Engine
Number of Cylinders
1
Displacement
10.3 cu-in (169 cc)
Max Output
5.7 H.P./3600 R.P.M.
Fuel Tank Capacity
Approx. 3.8 quar ts (3.6 liters)
Fuel
Unleaded Automobile Gasoline
Lube Oil Capacity
Star ting Method
Dry Weight
0.63 quar tz (60 liters)
Recoil Star t
33 lbs (15 Kg.)
MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06) — PAGE 11
MVC-88VGE/VGEW PLATE COMPACTOR — GENERAL INFORMATION
Definition of Plate Compactor
The Mikasa MVC-88VGE/VGEW is a walk behind, plate
compactor designed for the compaction of sand, mixed soils
and asphalt. This plate compactor is a powerful compacting tool
capable of applying a tremendous force in consecutive high
frequency vibrations to a soil surface. Its applications include
compacting for road, embankments and reservoirs as well as
backfilling for gas pipelines, water pipelines and cable installation
work.
Vibratory Plates
The vibratory plates of the MVC-88VGE/VGEW produce low
amplitude high frequency vibrations, designed to compact
granular soils and asphalt.
Frequency/Speed
The compactor's vibrating plate has a frequency range between
5800 vpm (vibrations per minute). The travel speed of the
compactor is approximately 56 feet/minute (17 meters/minute).
Engine
The Mikasa MVC-88VGE/VGEW Plate Compactor is equipped
with a Robin EX170D54011 air cooled, 4-cycle gasoline engine.
The engine drives an eccentric weight at a high speed to develop
a compaction force.
Controls
Before starting the MVC-88VGE/VGEW Plate Compactor, identify
and understand the function of the controls and components.
The resulting vibrations cause forward motion. The engine and
handle are vibration isolated from the vibrating plate.
l
PAGE 12 — MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06)
MVC-88VGE/VGEW PLATE COMPACTOR — COMPONENTS (COMPACTOR)
Figure 1. Plate Compactor Controls
Figure 1 shows the location of the basic controls and components
of the MVC-88VGE/VGEW Plate Compactor. The function of each
control is described below:
6.
Belt Cover – Remove this cover to gain access to the
V-belts. NEVER run the compactor without the V-belt cover.
If the V-belt cover is not installed, the possibility exists that
your hand may get caught between the V-belt and clutch,
causing serious injury and bodily harm.
1.
Water Tank Cap (VGEW Only) – Remove this cap to add
water to the water tank.
2.
Fuel Tank Cap – Remove this cap to add fuel.
7.
3.
Lifting Bale – When lifting of the compactor is required
either by forklift, crane etc., tie rope or chain around this
lifting point.
Vibrating Plate – A flat, open plate made of durable cast
iron construction used in the compacting of soil.
8.
Vibration Case – Encloses the eccentric, gears and
counter weights.
4.
Handle Bar – When operating the compactor use this
handle bar to maneuver the compactor.
9.
Water Tube (Sprinkler) – Supplies water to the soil via a
splash plate.
5.
Gasoline Engine – This plate compactor uses a ROBIN
engine. Refer to the ROBIN owner's manual for engine
information and related topics.
10. Water Shut-Off Valve – Turn this valve downward to let
water flow from the water tank to the water tube.
11. Water Tank (VGEW only) – Holds 13.7 quarts of water
(removable, no tools required).
MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06) — PAGE 13
MVC-88VGE/VGEW PLATE COMPACTOR — COMPONENTS ( ENGINE)
1
10
9
2
8
7
3
6
5
4
Figure 2. Engine Controls & Components
ENGINE COMPONENTS
5.
The engine (Figure 2) must be checked for proper lubrication and
filled with fuel prior to operation. Refer to the manufacturers Engine
manual for instructions & details of operation and servicing.
Fuel Valve Lever – OPEN to let fuel flow, CLOSE to stop
the flow of fuel.
6.
Choke Lever – Used in the starting of a cold engine, or in
cold weather conditions. The choke enriches the fuel
mixture.
1.
7.
Air Cleaner – Prevents dirt and other debris from entering
the fuel system. Remove wing-nut on top of air filter
cannister to gain access to filter element.
Fuel Filler Cap – Remove this cap to add unleaded
gasoline to the fuel tank. Make sure cap is tightened
securely. DO NOT over fill.
DANGER
Explosive
Fuel Hazard
NOTE
Adding fuel to the tank should be done only when
l an opportunity
the engine is stopped and has had
to cool down. In the event of a fuel spill, DO NOT
attempt to start the engine until the fuel residue
has been completely wiped up, and the area surrounding the
engine is dry.
2.
3.
4.
WARNING
Operating the engine without an air
filter, with a damaged air filter, or a filter
in need of replacement will allow dirt
to enter the engine, causing rapid
engine wear.
Burn Hazard
Engine components can generate extreme heat.
To prevent burns, DO NOT touch these areas
while the engine is running or immediately after
operating. NEVER operate the engine with the
muffler removed.
Throttle Lever – Used to adjust engine RPM speed (lever
advanced forward - SLOW, lever back toward operator FAST).
8.
Recoil Starter (pull rope) – Manual-starting method. Pull
the starter grip until resistance is felt, then pull briskly and
smoothly.
Spark Plug – Provides spark to the ignition system. Set
spark plug gap to 0.6 - 0.7 mm (0.028 - 0.031 inch) Clean
spark plug once a week.
9.
Muffler – Used to reduce noise and emissions.
Starter Grip– Pull the starter grip until resistance is felt,
then pull briskly and smoothly to start engine.
10. Fuel Tank – Holds approximately 1 gallon (3.6 liters) of
unleaded gasoline. For additional information refer to
engine owner's manual.
PAGE 14 — MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06)
MVC-88VGE/VGEW PLATE COMPACTOR — INSPECTION
Before Starting
1.
Read safety instructions at the
beginning of manual.
2.
Clean the compactor, removing
dirt and dust, particularly the
engine cooling air inlet, carburetor
and air cleaner.
3.
Check the air filter for dirt and dust. If air filter is dirty, replace
air filter with a new one as required.
4.
Check carburetor for external dirt and dust. Clean with dry
compressed air.
5.
Check fastening nuts and bolts for tightness. Loosened
screws or bolts due to vibration, could lead to unexpected
accident.
The Oil Alert System will automatically
stop the engine before the engine falls
below safe limits. Always be sure to
check the engine oil level prior to
starting the engine.
NOTE
Table 3. Oil Type
Season
Temperature
Oil Type
Summer
25°C or Higher
SAE 10W-30
Spring/Fall
25°C~10°C
SAE 10W-30/20
Winter
0°C or Lower
SAE 10W-10
Engine Oil Check
1.
To check the engine oil level, place the pump on secure
level ground with the engine stopped.
2.
Remove the filler dipstick from the engine oil filler hole
(Figure 3) and wipe clean.
DANGER
Explosive
Fuel Hazard
Adding fuel to the fuel tank should be done only
when the engine is stopped and has had an
opportunity to cool down. In the event of a fuel
spill, DO NOT attempt to start the engine until the
fuel residue has been completely wiped up, and the area
surrounding the engine is dry. DO NOT attempt to refuel the
compactor if the engine is hot! or running.
Fuel Check
Figure 3. Engine Oil Dipstick (Removal)
3. Insert and remove the dipstick without screwing it into the filler
neck. Check the oil level shown on the dipstick.
4. If the oil level is low (Figure 4), fill to the edge of the oil filler
hole with the recommended oil type (Table 3). Maximum oil
capacity is 0.63 quarts (0.60 liters).
1. Remove the gasoline cap located on top of fuel tank.
2. Visually inspect to see if the fuel level is low. If fuel is low,
replenish with unleaded fuel.
3. When refueling, be sure to use a strainer for filtration. DO
NOT top-off fuel. Wipe up any spilled fuel immediately!
Figure 4. Engine Oil Dipstick (Oil Level)
MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06) — PAGE 15
MVC-88VGE/VGEW— INSPECTION
2. The V-belt tension is proper if the V-belt bends 10 to 15 mm
(Figure 7) when depressed with finger at midway between
the clutch and vibration pulley shafts.
V-Belt Check
CAUTI
CAUTION
NEVER attempt to check the V-belt with the engine running.
Severe injury can occur of your hand (Figure 5) gets caught
between the V-belt and the clutch. Always use safety gloves.
CLUTCH
PULLEY
Figure 7. V-Belt Tension
VIBRATOR
PULLEY
3. A loose V-belt will decrease the power transmission output,
causing reduced compaction and premature wear of the
belt.
4. If the V-belt becomes worn or loose, replace it.
Figure 5. V-Belt Hazard
1. To check the V-belt tension, remove the three bolts that
secure the belt cover to the frame as shown in Figure 6.
Vibrator Oil Check
1. Place the MVC-88VGE/VGEW plate compactor horizontally
on a flat surface. Make sure the compactor is level when
checking the oil in the vibrator assembly.
2. Check vibrator oil level by removing the plug (vibrator oil gauge)
as shown in Figure 8. The oil level should be up to the oil plug.
The vibrator holds 140 cc (approximately 1 pint). IMPORTANT,
if oil is required, replace using only SAE10W-30 motor oil.
REMOVE
l
VIBRATOR
REMOVE
Figure 8. Vibrator Oil Plug
V-BELT
V-BELT COVER
Figure 6. V-Belt Cover Removal
PAGE 16 — MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06)
MVC-88VGE/VGEW— INITIAL START-UP
CAUTI
CAUTION
The CLOSED position of the
choke lever enriches the fuel
mixture for starting a COLD
engine. The OPEN position
provides the correct fuel
mixture for normal operation
after starting, and for restarting
a warm engine.
NOTE
D
DO NOT attempt to run the compactor until
the Safety and Initial Start-upsectionshave
been read and understood.
1. Place the fuel valve lever (Figure 9) in the "ON" position.
4. Place the throttle lever (Figure 12) halfway between fast
and slow.
FUEL
LEVER
THROTTLE
LEVER
Figure 9. Fuel Valve Lever
2. Place the Engine ON/OFF switch (Figure 10) in the "ON"
position.
ENGINE
ON/OFF
SWITCH
FAST
SLOW
Figure 12. Throttle Lever
OFF
5. Grasp the starter grip (Figure 13) and slowly pull it out. The
resistance becomes the hardest at a certain position, corresponding the compression point. Rewind the rope a little from
that point and pull out sharply.
ON
CAUTI
CAUTION
DO NOT pull the starter rope all the way to the end
Figure 10. Engine ON/Off Switch
3. Place the Choke Lever (Figure 11) in the "OPEN" position.
CHOKE
LEVER
DO NOT release the starter rope after pulling. Allow it to
rewind as soon as possible.
Nnnn
Nnnn
OPEN
CLOSED
D
STARTER GRIP
Figure 13. Starter Grip
Figure 11. Choke Lever
MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06) — PAGE 17
MVC-88VGE/VGEW— INITIAL START-UP/OPERATION
6. If the engine has started, slowly return the choke lever
(Figure 11) to the CLOSED position. If the engine has not
started repeat steps 1 through 5.
7. Before the compactor is put into operation run the engine for
3-5 minutes.
8. Check for abnormal engine noises or fuel leaks.
Stopping the Engine
CAUTI
CAUTION
D
NEVER stop the engine suddenly while working at high
speeds.
Operation
1. Place the throttle lever (Figure 12) in slow position, and
listen for the engine speed to decrease.
CAUTI
CAUTION
Make sure to follow all safety rules referenced in the safety
section of this manual before operating compactor. Keep work
area clear of debris and other objects that could cause
damage to the compactor or bodily injury.
2. Place the Engine ON/OFF switch (Figure 10) in the "OFF
" position.
3. Place the fuel valve lever (Figure 9) in the "OFF" position.
1. Once the engine has started, move the engine throttle lever
quickly to the fast position.
2. With the throttle lever in the fast position, the engine speed
should be around 2,300 RPM, therefore engaging the centrifugal clutch.
NOTE
ALWAYS move the throttle lever
quickly without hesitation,
because increasing the engine
speed slowly causes the clutch
to slip.
5. Firmly gasp the compactor's handle bar with both hands , the
compactor will begin moving forward.
6. Slowly walk behind the compactor and be on the lookout for
any large objects or foreign matter that might cause damage
to the compactor or bodily injury.
l
7. Compactor traveling speed may drop on soils which contain
clay, however there may be cases where traveling speed
drops because the compaction plate does not leave the
ground surface easily due to the composition of the soil. To
rectify this problem do the following:
■ Check the bottom plate to see if clay or equivalent
material has been lodge in the plate mechanism. If so,
wash with water and remove.
■ Remember the compactor does not work as efficiently
on clay or soils that have a high moisture content level.
■ If the soil has a high moisture level, dry soil to appropriate
moisture content level or carry out compaction twice.
PAGE 18 — MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06)
MVC-88VGE/VGEW— MAINTENANCE
CAUTI
CAUTION
CAUTI
CAUTION
These inspection intervals are for operation under normal
conditions. Adjust your inspection intervals based on the
number hours plate compactor is in use, and particular
working conditions.
Inspection and other services should always be carried out
on hard and level ground with the engine shutdown.
Inspection and Maintenance Service Tables.
1. To make sure your plate compactor is always in good
working condition before using, carry out the maintenance
inspection in accordance with Tables 4 through 6.
CAUTI
CAUTION
Fuel piping and connections should be replaced every 2
years.
Table 4. Engine Maintenance Schedule
DESCRIPTION (3)
OPERATION
BEFORE
CHECK
X
FIRST
EVERY
MONTH 3 MONTHS
OR
OR
10 HRS.
25 HRS.
EVERY
6 MONTHS
OR
50 HRS.
EVERY
YEAR
OR
100 HRS.
EVERY
2 YEARS
OR
200 HRS.
Engine Oil
CHANGE
CHECK
X
X
Air Cleaner
CHANGE
All Nuts & Bolts
Re-tighten If
Necessary
X (1)
X
CHECK-CLEAN
X
Spark Plug
REPLACE
X
Cooling Fins
CHECK
X
Spark Arrester
CLEAN
X
Fuel Tank
CLEAN
X
Fuel Filter
CHECK
X
Idle Speed
CHECK-ADJUST
X (2)
Valve Clearance
CHECK-ADJUST
Fuel lines
CHECK
X (2)
Every 2 years (replace if necessary) (2)
(1) Service more frequently when used in DUSTY areas.
(2) These items should be serviced by your service dealer, unless you have the proper tools and are mechanically
proficient. Refer to the HONDA Shop Manual for service procedures.
(3) For commercial use, log hours of operation to determine proper maintenance intervals.
MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06) — PAGE 19
MVC-88VGE/VGEW — MAINTENANCE
ENGINE OIL
TABLE 5. MACHINE INSPECTION
Item
Hours of Operation
Remarks
(Star ting check)
Every 8 hours (every
day)
Loosened or lost
screws
Every 8 hours (every
day)
Damage of any par t
Every 8 hours (every
day)
Function of controlling
system par t
Every 8 hours (every
day)
Vibrator oil check
Every 100 hours
See page 19.
Vibrator oil
replacement
Every 200 hours
See page 19.
V-belt (clutch) check
Every 200 hour
See page 19.
1. Drain the engine oil when the oil is warm as shown in
Figure 14.
2. Remove the dipstick and then unscrew the oil plug and
allow the oil to drain into a suitable container.
3. Replace engine oil with recommended type oil as listed
in Table 3. For engine oil capacity, see Table 2 (engine
specifications). DO NOT overfill.
4. Install drain bolt with sealing washer and tighten securely.
Daily Service
■ Check for leakage of fuel or oil.
■ Check engine oil.
■ Check for loose screws including tightness. See Table 6
below (tightening torque ), for retightening.
ENGINE AIR CLEANER
TABLE 6.
TIGHTENING TORQUE (in. kg/cm) Diameter
Material 6mm
8mm
10mm 12mm 14mm 16mm 18mm 20mm
4T
70
150
300
500
750
1,100
1,400
2,000
6-8T
100
250
500
800
1,300
2,000
2,700
3 ,8 0 0
11T
150
400
800
1,200
2,000
2,900
4,200
5,600
*
Figure 14. Engine Oil (Draining)
100 (6mm) 300 ~ 350 (8mm)l 650 ~ 700 (10mm)
* (In case counter-par t is of aluminum)
(Threads in use with this machine are all right handed)
Material and quality of material is marked on each bolt,
and screw.
1. Remove the air cleaner cover and foam filter element as
shown in Figure 15.
2. Tap the paper filter element (Figure 15) several times on a
hard surface to remove dirt, or blow compressed air [not
exceeding 30 psi (207 kPa, 2.1 kgf/cm2) through the filter
element from the air cleaner case side. NEVER brush off dirt.
Brushing will force dirt into the fibers. Replace the paper filter
element if it is excessively dirty.
3. Clean foam element in warm, soapy water or nonflammable
solvent. Rinse and dry thoroughly. Dip the element in clean
engine oil and completely squeeze out the excess oil from the
element before installing.
PAGE 20 — MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06)
MVC-88VGE/VGEW— MAINTENANCE
Checking and Replacing the V-Belt and Clutch
1. After 200 hours of operation, remove the upper belt cover to
check the V-belt tension. Tension is proper if the belt bends
about 10 mm when depressed strongly with finger between
shafts. Loose or worn V-belts reduces power transmission
efficiency, causing weak compaction and reduces the life of
the belt itself.
CAUTI
CAUTION
Whenever the compactor's vibration becomes weak or lost
during normal operation regardless of operation hours, check
the V-belt and clutch immediately.
■ Replacing the V-belt
Remove the upper and lower belt covers. Engage an offset
wrench (13 mm) or the like to vibrator pulley (lower) fastening
bolt. Engage waste cloth or the like at midway of V-belt on the left
side and while pulling it back strongly, rotate the offset wrench
clockwise so that the V-belt will come off.
Figure 15. Air Cleaner
CHANGING VIBRATOR OIL
1. When changing the vibrator oil, remove the drain plug
located at the bottom- right of the vibrator (Figure 8), and
simply tip the compactor to drain the oil. Note that the oil will
drain more easily while it is hot. Remember to use only
10W-30 motor oil when replacing vibrator oil.
CAUTI
CAUTION
■ Reinstalling the V-belt
Engage V-belt to lower vibrator pulley and push the V-belt to left
side of upper clutch and, in the same manner as in removal,
rotate offset wrench clockwise so that the V-belt goes back on.
■ Checking Clutch
Check the clutch simultaneously with V-belt checking. With belt
removed, check outer drum of the clutch for seizure and "V"
groove for wear or damage with your eyes. Clean the "V" groove
as necessary. Wear of lining or shoe should be checked
frequently. If the shoe is worn, power transmission becomes
deficient and slipping will result.
NEVER attempt to check the V-belt with the engine running.
Severe injury can occur if your hand (Figure 5) gets caught
between the V-belt and the clutch. Always use safety gloves.
MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06) — PAGE 21
MVC-88VGE/VGEW— PREPARATION FOR LONG -TERM STORAGE
Plate Compactor Storage
For storage of the plate compactor for over 30 days, the
following is required:
■ Drain the fuel tank completely or add STA-BIL to the fuel.
■ Run the engine until the fuel is completely consumed.
■ Completely drain the oil from the engine crankcase and
follow procedures described in the ROBIN engine Owner's
Manual for engine storage.
■ Completely drain the compactor's hydraulic oil from the
vibrating case.
■ Clean entire plate compactor, especially the bottom plate
removing all dirt and foreign matter.
■ Cover plate compactor and engine with plastic covering
or equivalent and store in a clean, dry place.
l
PAGE 22 — MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06)
MVC-88VGE/VGEW—TROUBLESHOOTING (ENGINE)
Practically all breakdowns can be prevented by proper
handling and maintenance inspections, but in the event of a
breakdown, please take a remedial action following the
diagnosis based on the Engine , and Compactor
Troubleshooting (Tables 7, and 8) information.
If the problem cannot be remedied, please leave the unit as
is and consult Multiquip's Service Department.
TABLE 7. ENGINE TROUBLESHOOTING
SYMPTOM
Difficult to star t, "fuel is available, but no
SPARK at spark plug".
POSSIBLE CAUSE
Spark plug bridging?
Check gap, insulation or
replace spark plug.
Carbon deposit on spark plug?
Clean or replace spark plug.
Shor t circuit due to deficient spark plug
insulation?
Check spark plug insulation,
replace if worn.
Improper spark plug gap?
Set to proper gap.
ON/OFF switch is shor ted?
Check switch wiring, replace
switch.
Ignition coil defective?
Replace ignition coil.
Difficult to star t, "fuel is available, and Improper spark gap, points dir try?
SPARK is present at the spark plug".
Difficult to star t, "fuel is available, spark
is present and compression is normal"
Difficult to star t, "fuel is available, spark
is present and compression is low"
No fuel present at carburetor.
SOLUTION
Set correct spark gap and
clean points.
Condenser insulation worn or shor t
circuiting?
Replace condenser.
Spark plug wire broken or shor t circuiting?
R e p l a c e d e fe c t i ve s p a r k p l u g
wiring.
Wrong fuel type?
Flush fuel system, and replace
with correct type of fuel.
Water or dust in fuel system?
Flush fuel system.
Air cleaner dir ty?
Clean or replace air cleaner.
Suction/exhaust valve stuck or protruded?
Re-seat valves.
Piston ring and/or cylinder worn?
Replace piston rings and or
piston.
Cylinder head and/or spark plug not
tightened properly?
Torque cylinder head bolts and
spark plug.
Head gasket and/or spark plug gasket
damaged?
Replace head and spar k plug
gaskets.
Fuel not available in fuel tank?
Fill with correct type of fuel.
Fuel cock does not open properly?
Apply lubr icant to loosen fuel
cock lever, replace if necessary.
Fuel filter clogged?
Replace fuel filter.
Fuel tank cap breather hole clogged?
Clean or replace fuel tank cap.
Air in fuel line?
Bleed fuel line.
MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06) — PAGE 23
MVC-88VGE/VGEW—TROUBLESHOOTING (ENGINE/COMPACTOR)
TABLE 7. ENGINE TROUBLESHOOTING (CONTINUED)
SYMPTOM
"Weak in power" compression is
proper and does not misfire.
"Weak in power" compression is
proper but misfires.
Engine overheats.
Rotational speed fluctuates.
Recoil star ter malfunction.
POSSIBLE CAUSE
Air cleaner not clean?
Clean or replace air cleaner
Improper level in carburetor?
Check float adjustment, re-build
carbureator.
Defective Spark plug?
Clean or replace spark plug.
Water in fuel system?
Flush fuel system, and replace
with correct type of fuel.
Dir ty spark plug?
Clean or replace spark plug.
Ignition coil defective?
Replace ignition coil.
Spark plug heat value improper?
Replace with correct type of
spark plug.
Correct type of fuel?
Replace with correct type of fuel
Cooling fins dir ty?
Clean cooling fins.
Governor adjusted correctly?
Adjust governor.
Governor spring defective?
Replace governor spring.
Fuel flow restricted?
C h e c k e n t i r e f u e l s y s t e m fo r
leaks or clogs.
Recoil mechanism clogged with dust and Clean recoil assembly with soap
and water.
dir t?
Spiral spring loose?
l
SOLUTION
Replace spiral spring.
TABLE 8. PLATE COMPACTOR TROUBLESHOOTING
SYMPTOM
POSSIBLE CAUSE
SOLUTION
Engine speed too low?
Set engine speed to correct RPM.
Clutch slips?
Check or replace clutch.
V-belt slips?
Adjust or replace V-belt.
Travel speed too low, and vibration is weak. Excessive oil in vibrator?
Drain excess oil and fill to proper level.
Malfunction in vibrator housing?
Check eccentric, gears and counter
weights.
Bearing Failure?
Replace bearing.
Insufficient Engine Output?
Check engine, compression, etc.
PAGE 24 — MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06)
NOTE PAGE
MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06) — PAGE 25
MVC-88VGE/VGEW— EXPLANATION OF CODES IN REMARKS COLUMN
The following section explains the different symbols and remarks
used in the Parts section of this manual. Use the help numbers
found on the back page of the manual if there are any questions.
The contents and part numbers listed in the parts section are
subject to change without notice. Multiquip does not
guarantee the availability of the parts listed.
Sample Parts List:
NO.
1
2
2
3
4
REMARKS
INCLUDES ITEMS W/
NOT SOLD SEPARATELY
MQ-45T ONLY
MAKE LOCALLY
S/N 2345B AND ABOVE
*
A/R (As Required) is generally used for hoses or other parts
that are sold in bulk and cut to length.
A blank entry generally indicates that the item is not sold
separately. Other entries will be clarified in the “Remarks”
Column.
Some of the most common notes found in the “Remarks”
Column are listed below. Other additional notes needed to
describe the item can also be shown.
Assembly/Kit - All items on the parts list with the same unique
symbol will be included when this item is purchased.
Indicated by:
NO. Column
“INCLUDES ITEMS W/(unique symbol)”
Unique Symbols - All items with same unique symbol
( , #, +, %, or >) in the number column belong to the same
assembly or kit, which is indicated by a note in the “Remarks”
column.
*
Duplicate Item Numbers - Duplicate numbers indicate
multiple part numbers are in effect for the same general item,
such as different size saw blade guards in use or a part that
has been updated on newer versions of the same machine.
NOTE
Numbers Used - Item quantity can be indicated by a number,
a blank entry, or A/R.
REMARKS Column
PART NO. PART NAME
QTY.
12345
BOLT ....................... 1....
WASHER, 1/4 IN. ...........
12347
WASHER, 3/8 IN. .... 1....
12348
HOSE .................... A/R ..
12349
BEARING ................ 1....
*
*
QTY. Column
When ordering a part that has more
than one item number listed, check
the remarks column for help in
determining the proper part to order.
Serial Number Break - Used to list an effective serial number
range where a particular part is used.
Indicated by:
“S/N XXXXX AND BELOW”
“S/N XXXX AND ABOVE”
“S/N XXXX TO S/N XXX”
Specific Model Number Use - Indicates that the part is used
only with the specific model number or model number variant
listed. It can also be used to show a part is NOT used on a
specific model or model number variant.
Indicated by:
“XXXXX ONLY”
“NOT USED ON XXXX”
l
“Make/Obtain Locally” - Indicates that the part can be
purchased at any hardware shop or made out of available
items. Examples include battery cables, shims, and certain
washers and nuts.
TBD (To Be Determined) is generally used to show a part that
has not been assigned a formal part number at time of
publication.
“Not Sold Separately” - Indicates that an item cannot be
purchased as a separate item and is either part of an
assembly/kit that can be purchased, or is not available for
sale through Multiquip.
PART NO. Column
Numbers Used - Part numbers can be indicated by a number,
a blank entry, or TBD.
A blank entry generally indicates that the item is not sold
separately or is not sold by Multiquip. Other entries will be
clarified in the “Remarks” Column.
PAGE 26 — MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06)
MVC-88VGE/VGEW — SUGGESTED SPARE PARTS
MVC-88VGE/VGEW 1 TO 5 UNITS WITH ROBIN
EX170D54011 ENGINE
1 to 5 Units
Qty.
P/N
Description
3 ......... 070100332 ............. V-BELT
5 ......... 0650149670 ........... SPARK PLUG
1 ......... 2825011118 ........... ROPE, RECOIL STARTER
5 ......... 2773261107 ........... ELEMENT, AIR CLEANER
1 ......... 0430430060 ........... CAP, FUEL TANK
1 ......... 0641360010 ........... FUEL FILTER, FUEL TANK
4 ......... 939010140 ............. SHOCK ABSORBER
MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06) — PAGE 27
MVC-88VGE/VGEW— NAME PLATE AND DECALS
NAME PLATE AND DECALS
9
10
11
2
3
1
4
5
6
8
7
l
6
PAGE 28 — MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06)
MVC-88VGE/VGEW— NAME PLATE AND DECALS
NAME PLATE AND DECALS
NO
PART NO
PART NAME
QTY. REMARKS
1
920207690
DECAL, READ OWNERS MANUAL ....... 1 ........ NPA-769
2
920203290
DECAL, CAUTION ................................. 1 ........ NPA-329
3
920208450
DECAL, LIFTING ................................... 1 ........ NPA-845
4
920203060
DECAL, CAUTION (START ENG/VIBR) . 1 ........ NPA-306
5
920208350
DECAL, V- BELT RPF-3330 ................... 1 ........ NPA-835
6
920201580
DECAL, MQ LOGO ................................ 2 ........ NPA-158
7
920105070
DECAL, MIKASA LOGO (NAME) .......... 1 ........ NPA-507
8
920201950
DECAL, MOTOR OIL .............................. 1 ........ NPA-195
9
920101410
DECAL, MIKASA LOGO (TRIANGLE) ...1 ........ NPA-141
10
NAMEPLATE, SERIAL NO. ................... 1 ........ CONTACT MQ PARTS DEPT. W/MODEL & S/N
11
920203330
EAR PROTECTION LABEL ................... 1 ........ NPA-333
SEE DECAL ILLUSTRATIONS PAGE.
MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06) — PAGE 29
MVC-88VGE/VGEW— BODY ASSY.
BODY ASSY.
106
104
105
108
101
104
105
107
102
96
102
103
103
9795
93
91
92
94
92
35
36
37
46
38
32
41
33
31
93
95
9796
42
12
52
57
32 54
55
56
l
51
47
45
4849
54
55
56
33
39
25
23
40
43
54
55
56
24
53
24
25
23
21
PAGE 30 — MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06)
MVC-88VGE/VGEW— BODY ASSY.
BODY
NO
12
21
23
24
25
31
32
33
35
36
37
38
39
40
41
42
43
45
46
47
48
49
51
52
53
54
55
56
57
91
92
93
94
95
96
97
101
102
103
104#
105#
106#
107#
108#
ASSY.
PART NO
416454360
416115973
939010140
020310080
030210250
416115980
001221025
030210250
911221701
001220845
030208200
031108160
404412290
416452780
031108160
022710809
959404350
416338990
2062600113
416452800
952400130
009110004
070100332
416115950
416010020
001220825
030208200
031108160
001220820
416910070
416452730
404433430
416452360
952405600
001211253
030212300
416115940
001221025
030210250
416459340
009120407
416217070
416118520
416459320
PART NAME
QTY.
REMARKS
RUBBER PLATE 25X25X8
1
VIBRATING PLATE
1
SHOCK ABSORBER 50D-45H
4
NUT M10
4
WASHER, LOCK M10
4
BASE
1
BOLT 10X25 T
4
WASHER, LOCK M10
4
ENGINE ASSY. EX170D54011
1
BOLT 8X45 T
4
WASHER, LOCK M8
4
WASHER, FLAT M8
4
ENGINE NUT
1
ENGINE NUT (W/BOLT)
1
WASHER, FLAT M8
1
NYLON NUT M8
1
EARTH WIRE
1
CLUTCH ASSY.
1
KEY 4.77 X 4.77 X 35
1
COLLAR 19.05-25-15.6
1
WASHER
1
SOCKET HEAD BOLT 5/16X24
1
V-BELT RPF-3330
1
BELT COVER (INSIDE)
1
BELT COVER
1
BOLT 8X25 T
4
WASHER, LOCK M8
5
WASHER, FLAT M8
1
BOLT 8X20 T
1
VIB. PROOF HANDLE ............................ 1 ......... INCLUDES ITEMS W/ #
COLLAR 13-20-44
2
RUBBER 20X32X28.5/52H
2
HANDLE STOPPER
2
WASHER 12.5 X 35 X 4.5
2
BOLT 12X65 H
2
WASHER, LOCK M12
2
GUARD HOOK
1
BOLT 10X25 T
4
WASHER, LOCK M10
4
RUBBER
2
BOLT, SUNK HEAD 10X20T
2
GRIP, HANDLE
1
VIB. PROOF HANDLE
1
NUT, VIB. PROOF HANDLE
2
MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06) — PAGE 31
MVC-88VGE/VGEW— VIBRATOR ASSY.
VIBRATOR ASSY.
l
PAGE 32 — MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06)
MVC-88VGE/VGEW— VIBRATOR ASSY.
VIBRATOR ASSY.
NO
PART NO
A
416910030
61#
416115991
62#
953400270
63#
953405260
64
001221640
65
030216400
66
031116260
68#
416215530
69#
040306211
70#
416338900
71#
416338910
72#
416338920
73#
060403060
74#
050101000
75#
001220825
76#
030208200
78#
416454430
79#
951405240
80#
952404250
81#
001221025
82#
030210250
PART NAME
QTY.
REMARKS
VIBRATOR ASSY .................................. 1 ........... INCLUDES ITEMS W/ #
VIBRATING CASE
1
PLUG 1/4X14 10L
1
PACKING 1/4
1
BOLT 16X40 T
4
WASHER, LOCK M16
4
WASHER, FLAT M16
4
ECCENTRIC ROTATOR
1
BEARING 6211C3
2
CASE COVER (R)
1
CASE COVER (L)
1
BELT COVER GUARD
1
OIL SEAL TC-35488
1
O-RING G-100
2
BOLT 8X25 T
8
WASHER, LOCK M8
8
PULLEY A1-28-81-20
1
KEY 7X7X19 R
1
WASHER 11X40X4
1
BOLT 10X25 T
1
WASHER, LOCK M10
1
MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06) — PAGE 33
MVC-88VGE/VGEW— SPRINKLER ASSY. (OPTION)
SPRINKLER ASSY. (OPTION)
122
123
121
123
124
113
112
114
l
111
l
119
116
118
120
115
117
118
PAGE 34 — MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06)
MVC-88VGE/VGEW— SPRINKLER ASSY. (OPTION)
SPRINKLER ASSY. (OPTION)
NO
111
112
113
114
115
116
117
118
119
120
121#
122#
123#
124#
PART NO
416910010
033910050
953406390
954403241
416338930
416338940
416452750
001220825
416453780
416452790
954300342
001241030
033910010
022910180
PART NAME
QTY.
REMARKS
WATER TANK (W/CAP ONLY) ...... 1 ............... REPLACES 416116010, INCLUDES ITEMS W/#
WASHER 14.5X30X1.6
1
PACKING 13X28X2
1
COCK PT1/4
1
SPRINKLING PIPE
1
PIPE HOLDER (L)
1
PIPE HOLDER (R)
1
FLANGE BOLT 8X25
2
PACKING 8X19X2T
3
STAY, PIPE HOLDER
1
CAP, WATER TANK (NBR)
1
BOLT 10X30
1
WASHER 10.5X21X2
2
NYLON NUT M10
1
MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06) — PAGE 35
MVC-88VGE/VGEW— TRANSPORT WHEEL ASSY. (OPTION)
TRANSPORT WHEEL ASSY. (OPTION )
l
PAGE 36 — MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06)
MVC-88VGE/VGEW— TRANSPORT WHEEL ASSY. (OPTION)
TRANSPORT WHEEL ASSY. (OPTION )
NO
1
2
3
4
5
6
PART NO
416116160
959404310
031120320
025203030
416454150
025403025
PART NAME
WHEEL SHAFT
WHEEL 150X42
WASHER, FLAT M20
SPLIT COTTER PIN 3X30
ROLLER
SPRING PIN 3X25
QTY.
1
2
2
2
2
3
REMARKS
MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06) — PAGE 37
ROBIN EX170D54011 ENGINE — AIR CLEANER ASSY.
AIR CLEANER ASSY.
272
250
270
A
520
210
580
850
200
260
l
220
570
PAGE 38 — MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06)
ROBIN EX170D54011 ENGINE — AIR CLEANER ASSY.
AIR CLEANER ASSY.
NO.
PART NO.
A
2773261500
200# 2773263008
210# 2773261008
220# 2773260408
250# 2773264008
260# 2773260908
270# 2773274108
272# 2773274008
272# 2773274308
520# 2773261107
570
0023806000
580
0110060050
850
0851080000
PART NAME
QTY. REMARKS
AIR CLEANER AY. ....................................... 1 ...... INCLUDES ITEMS W/ #
BASE CP CLEANER
1
PACKING CLEANER
1
GASKET, CLEANER
1
COVER CP CLEANER
1
LABEL, THROTTLE
1
WING NUT(P)
1
WING NUT
1
WING NUT
1
CLEANER ELEMENT
1
FLANGE NUT
2
FLANGE BOLT
1
RUBBER PIPE, 8X11XM
1
MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06) — PAGE 39
ROBIN EX170D54011 ENGINE — CAMSHAFT ASSY.
CYLINDER BARREL ASSY.
l
PAGE 40 — MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06)
ROBIN EX170D54011 ENGINE — CAMSHAFT ASSY.
CAMSHAFT ASSY.
NO
PART NO
10
2773160101
25
2773510103
27
0240060010
34%
2773860103
35%
2773640103
2773650103
37%
38%
2773870103
150
2773560111
160
2773691103
163
2773710103
166
2773690203
170
2773691313
PART NAME
QTY.
REMARKS
CAMSHAFT .............................................. 1 ................. INCLUDES ITEMS W/%
PIN, CAMSHAFT
1
O-RING
1
PIN, SPRING
1
RELEASE LEVER
1
CLIP
1
RETURN SPRING
1
CHAIN, TIMING
1
TENSIONER
1
SPRING, TENSIONER
1
PIN, TENSIONER
1
CHAIN, GUIDE
1
MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06) — PAGE 41
EX-170D40050 — CARBURETOR ASSY.
CARBURETOR ASSY.
210
210-8
210-11
210-2
210-1
210-3
210-62
210-5
210-32
210-45
210-302
210-303
210-44
210-22
210-20
210-14
210-24
210-18
224
210-19
l
210-104
210-28
210-15
550-1
210-16
550-2
CARBURETOR
REFERENCE
ONLY
540
210-17
210-12
PAGE 42 — MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06)
EX-170D40050 — CARBURETOR ASSY.
CARBURETOR ASSY.
NO
PART NO
210
2776230220
210-1
2776253508
*
210-2
2096235108
*
2776252508
210-3
*
210-5
2466242008
*
2776252008
210-8
*
210-11
2776253108
*
2276245108
210-12
*
210-14
2776250008
*
2776251508
210-15
*
210-16
2776250608
*
2146245008
210-17
*
210-18
2146254008
*
210-19
2266250608
*
210-20
2776244008
*
210-22
2266241208
*
210-24
2266270108
*
210-28
2776236008
*
210-32
2466239008
*
210-44
2486241008
*
210-45
1066241008
*
210-62
2366268008
*
210-104
* 2366254108
210-302
2776211018
*
210-303
* 2776210018
224
2774380101
540
27732902J1
550-1
27735902J3
550-2
27735903J3
PART NAME
QTY. REMARKS
CARBURETOR ASSY. .................................... 1....... INCLUDES ITEMS W/
*
THROTTLE VALVE
1
SCREW
1
CHOKE VALVE
1
PILOT JET
1
CHOKE LEVER
1
THROTTLE SHAFT
1
BOLT
1
NEEDLE
1
FLOAT PIN
1
FLOAT BODY
1
PACKING
1
FLOAT CHAMBER PACKING
1
FLOAT ASSY.
1
MAIN NOZZLE
1
MAIN JET
1
CLIP
1
BOLT
1
SEAL, THROTTLE
1
AIR JET
1
AIR JET (PILOT)
1
SEAL
1
PACKING
1
PACKING
1
CUP
1
CHOKE LEVER
1
INSULATOR
1
GASKET (1), INSULATOR
1
GASKET (2), INSULATOR
1
MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06) — PAGE 43
ROBIN EX170D54011 ENGINE — CRANKCASE ASSY.
CRANKCASE ASSY.
l
PAGE 44 — MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06)
ROBIN EX170D54011 ENGINE — CRANKCASE ASSY.
CRANKCASE ASSY.
NO
PART NO
10
2771010241
30
* 0440250200
0600280021
40
*
50
* 2771501103
75
* 0440060020
80
0401140030
90$
0211140020
210
2771100221
220% 0440250210
230% 0600250140
250
27745004H1
260
2774190103
270
2776360113
275
2776500103
280$ 0213160020
281
0213160020
300
0010408350
700
2771501103
960
2779900107
PART NAME
QTY. REMARKS
CRANKCASE CP, W/OIL SENSOR ............. 1 ........ INCLUDES ITEMS W/
*
OIL SEAL
1
BALL BEARING
1
PIPE KNOCK
2
OIL SEAL
1
PLUG
2
GASKET
2
MAIN BEARING COVER CP ....................... 1 ........ INCLUDES ITEMS W/%
OIL SEAL
1
BALL BEARING
1
GOVERNOR GEAR
1
GOVERNOR SLEEVE
1
OIL GAUGE
1
FILLER, PLUG
1
GASKET
1
GASKET
1
FLANGE BOLT
6
PIPE KNOCK
2
GASKET SET .............................................. 1 ........ INCLUDES ITEMS W/ $, ITEMS 620
AND 690 IN CYLINDER HEAD ASSY,
AND ITEM 340 IN MUFFLER ASSY
MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06) — PAGE 45
EX-170D40050 — CRANKSHAFT/PISTON ASSY.
CRANKSHAFT/PISTON ASSY.
l
PAGE 46 — MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06)
EX-170D40050 — CRANKSHAFT/PISTON ASSY.
CRANKSHAFT/PISTON ASSY.
NO
PART NO
PART NAME
QTY.
REMARKS
10
2772090141
CRANKSHAFT
1
50
0180140020
FLANGE NUT
1
70
0323030010
WOODRUFF KEY
1
80
2062600113
KEY
1
90
0200080050
WASHER
1
100
0011308200
BOLT & WASHER ASSY.
1
310
2772250110
CONNECTING ROD ASSY. ...................... 1 ................. INCLUDES ITEMS W/
*
320
2772300103
CONNECTING ROD BOLT
2
*
350
2772330103
PISTON PIN
1
360
27723401J3
PISTON STD.
1
360
27723403H3
PISTON, 0.25 O.S.
1
360
27723404H3
PISTON, 050 O.S.
1
370
2772350117
PISTON RING SET STD.
1
370
2772350217
PISTON RING SET, 0.25 O.S.
1
370
2772350317
PISTON RING SET, 0.5 O.S.
1
380
0565160010
CLIP
2
MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06) — PAGE 47
EX-170D40050 — CYLINDER HEAD ASSY.
CYLINDER ASSY.
l
PAGE 48 — MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06)
EX-170D40050 — CYLINDER HEAD ASSY.
CYLINDER ASSY.
NO
PART NO
20#
2371420203
26#
2771601001
30
2793360103
40
2693370103
60#
0105080250
70#
0105060351
80
27733401H3
90
27733501H3
95
13210KA031
200
2773500201
200-1 2773500203
200-2 0031305000
220
2773610100
225
2773620200
230+ 0149050020
231$ 0149050020
240+ 0170050030
241$ 0170050030
290
0110060020
610
2771300111
620
2771500123
630
0110080240
631
0010408350
680
2771550101
690
2771600113
710
0110060020
PART NAME
QTY.
REMARKS
VALVE GUIDE
2
STEM SEAL
1
VALVE, SPRING
2
SPRING RETAINER
2
STUD
2
STUD
2
INTAKE VALVE
1
EXHAUST VALVE
1
COLLET VALVE
4
PIN, ROCKER
1
PIN (ONLY), ROCKER
1
CLIP 104#
ROCKER, ARM ASSY. IN ............................ 1 ........ INCLUDES ITEMS W/ +
ROCKER, ARM EX ...................................... 1 ........ INCLUDES ITEMS W/ $
ADJUSTING SCREW
1
ADJUSTING SCREW
1
NUT
1
NUT
1
FLANGE BOLT
1
CYLINDER HEAD ........................................ 1 ........ INCLUDES ITEMS W/ #
GASKET HEAD
1
FLANGE BOLT
4
FLANGE BOLT
1
ROCKER, COVER
1
GASKET, LOCKER COVER
1
FLANGE BOLT
4
MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06) — PAGE 49
EX-170D40050 — FUEL TANK ASSY.
FUEL TANK ASSY.
l
PAGE 50 — MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06)
EX-170D40050 — FUEL TANK ASSY.
FUEL TANK ASSY.
NO
PART NO
10
2776010201
20
0732005181
23
2779510103
30
0430430060
40
0641360010
48
0505120020
60
0023806000
63
0110060130
80
0851960000
90
0561100030
PART NAME
FUEL TANK
LABEL, WARNING
LABEL, MODEL
FUEL TANK, CAP
FUEL FILTER
UNION
FLANGE, NUT
FLANGE, BOLT
RUBBER PIPE, 6DX11D
HOSE CLAMP, 10DX8BX1T
QTY.
1
1
1
1
1
1
2
1
1
2
REMARKS
MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06) — PAGE 51
EX-170D40050 — GOVERNOR ASSY.
GOVERNOR ASSY.
450
30
70
10
50
310
440
40
480
60
340
350
80
322
355
360
440
485
365
396
395
435
l
20
PAGE 52 — MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06)
EX-170D40050 — GOVERNOR ASSY.
GOVERNOR ASSY.
NO
PART NO
10
2774230123
20
2774220133
30
2774270111
40
2774280123
50
0031305000
60
0130060240
70
0186060020
80
2794250263
310
2774330601
322
2774370101
340
2774350203
350
2774450103
355
0217060070
360
0043106250
365
2374500423
395
2774390203
396
0131050030
435
2774600201
440
0043104080
450
0023506000
480
2674510103
485
0110060020
PART NAME
GOVERNOR, LEVER
GOVERNOR, SHAFT
GOVERNOR, ROD
ROD, SPRING
CLIP
BOLT & WASHER ASSY
NUT
GOVERNOR, SPRING
SPEED CONTROL, LEVER
LINK ROD CP
STOP, PLATE
FRICTION PLATE W/ LOCK
FRICTION, WASHER
SCREW
SPRING, ADJUST
CLAMP
SCREW AND WASHER ASSY
SPEED, CONT. BRACKET
SCREW
LOCK NUT
RETURN SPRING
FLANGE, BOLT
QTY.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
2
REMARKS
MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06) — PAGE 53
EX-170D40050 — IGNITION COIL/FLYWHEEL ASSY.
ELECTRIC DEVICE ASSY.
700 740
10
70
741
705
60
30
50
100
120
l
11
110
PAGE 54 — MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06)
EX-170D40050 — IGNITION COIL/FLYWHEEL ASSY.
ELECTRIC DEVICE ASSY.
NO
PART NO
10
2777923011
11
2777943101
30
0011406250
50
27773102H1
60
0660000361
70
0150040090
100
0650149670
110
0655000270
120
2795520103
700
2777630111
705
KU31104311
740
0011406160
741
0152050010
PART NAME
FLYWHEEL
IGNITION COIL
BOLT & WASHER
WIRE 2
STOP SWITCH ASSY., ON-OFF
TAPPING SCREW
SPARK PLUG
SPARK PLUG CAP
GROMMET, PLUG CAP
OIL SENSOR CP
FLOAT C/U CP
BOLT AND WASHER ASSY
TAPPING SCREW
QTY.
1
1
2
1
1
2
1
1
1
1
1
2
1
REMARKS
MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06) — PAGE 55
EX-170D40050 — MUFFLER ASSY.
MUFFLER ASSY.
l
PAGE 56 — MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06)
EX-170D40050 — MUFFLER ASSY.
MUFFLER ASSY.
NO
PART NO
310
2763010121
320
2773420111
340
2773520203
350
9802008280
360
0152060090
361
0110060010
365
0110080150
440
27737001H1
445
0150040060
PART NAME
MUFFLER
MUFFLER COVER
GASKET, MUFFLER
FLANGE, NUT
TAPPING BOLT
FLANGE BOLT
FLANGE BOLT
DEFLECTOR
TAPPING SCREW
QTY.
1
1
1
2
2
1
1
1
2
REMARKS
MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06) — PAGE 57
EX-170D40050 — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
l
PAGE 58 — MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06)
EX-170D40050 — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
NO
PART NO
10
2775120201
20
0732005140
40
0110060030
60
2775271111
61
2775270203
80
0010406160
81
0110060020
210
2695020130
210-1
* 2705011508
210-2
* 2695012008
2825011118
210-3
*
210-4
* 2615010008
210-5
* 2705012508
210-6
* 2275013108
210-7
* 2275013508
210-11
2695014518
*
210-35
* 2705026108
210-49
* 2275015208
220
0110060010
PART NAME
QTY.
REMARKS
BLOWER, HOUSING CP
1
LABEL, TRADEMARK
1
FLANGE, BOLT
4
BAFFLE, CASE 1
1
BAFFLE, HEAD 2
1
FLANGE, BOLT
1
FLANGE, BOLT
1
RECOIL STARTER ASSY. ...................... 1.................... INCLUDES ITEMS W/
*
SPIRAL, SPRING
1
REEL
1
STARTER ROPE
1
STARTER KNOB
1
RACHET
2
FRICTION SPRING
1
RETURN SPRING
2
STARTER PULLEY
1
RACHET GUIDE
1
SET SCREW
1
FLANGE, BOLT
1
MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06) — PAGE 59
EX-170D40050 — TOOL KIT ASSY.
TOOL KIT
10
l
PAGE 60 — MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06)
EX-170D40050 — TOOL KIT ASSY.
TOOL KIT
NO
PART NO
10
27790301H0
PART NAME
TOOL KIT
QTY.
1
REMARKS
MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06) — PAGE 61
TERMS AND CONDITIONS OF SALE — PARTS
Effective: February 22, 2006
PAYMENT TERMS
5.
Parts must be in new and resalable condition, in the original Multiquip package (if
any), and with Multiquip part numbers
clearly marked.
6.
The following items are not returnable:
Terms of payment for parts are net 30 days.
FREIGHT POLICY
All parts orders will be shipped collect or
prepaid with the charges added to the invoice.
All shipments are F.O.B. point of origin.
Multiquip’s responsibility ceases when a signed
manifest has been obtained from the carrier,
and any claim for shortage or damage must be
settled between the consignee and the carrier.
a. Obsolete parts. (If an item is in the
price book and shows as being replaced by another item, it is obsolete.)
b. Any parts with a limited shelf life
(such as gaskets, seals, “O” rings,
and other rubber parts) that were purchased more than six months prior to
the return date.
MINIMUM ORDER
Multiquip reserves the right to quote and sell
direct to Government agencies, and to Original
Equipment Manufacturer accounts who use
our products as integral parts of their own
products.
SPECIAL EXPEDITING SERVICE
A $35.00 surcharge will be added to the invoice
for special handling including bus shipments,
insured parcel post or in cases where Multiquip
must personally deliver the parts to the carrier.
LIMITATIONS OF SELLER’S LIABILITY
RETURNED GOODS POLICY
d. Special order items.
Return shipments will be accepted and credit
will be allowed, subject to the following provisions:
e. Electrical components.
Multiquip shall not be liable hereunder for
damages in excess of the purchase price of the
item with respect to which damages are
claimed, and in no event shall Multiquip be
liable for loss of profit or good will or for any
other special, consequential or incidental damages.
f. Paint, chemicals, and lubricants.
LIMITATION OF WARRANTIES
g. Decals and paper products.
1.
h. Items purchased in kits.
No warranties, express or implied, are made
in connection with the sale of parts or trade
accessories nor as to any engine not manufactured by Multiquip. Such warranties made in
connection with the sale of new, complete units
are made exclusively by a statement of warranty packaged with such units, and Multiquip
neither assumes nor authorizes any person to
assume for it any other obligation or liability
whatever in connection with the sale of its
products. Apart from such written statement of
warranty, there are no warranties, express,
implied or statutory, which extend beyond the
description of the products on the face hereof.
The minimum charge for orders from Multiquip
is $15.00 net. Customers will be asked for
instructions regarding handling of orders not
meeting this requirement.
2.
A Returned Material Authorization must
be approved by Multiquip prior to shipment.
To obtain a Return Material Authorization,
a list must be provided to Multiquip Parts
Sales that defines item numbers, quantities, and descriptions of the items to be
returned.
a. The parts numbers and descriptions
must match the current parts price
list.
b. The list must be typed or computer
generated.
l
c. The list must state the reason(s) for
the return.
d. The list must reference the sales
order(s) or invoice(s) under which the
items were originally purchased.
e. The list must include the name and
phone number of the person requesting the RMA.
3.
A copy of the Return Material Authorization must accompany the return shipment.
4.
Freight is at the sender’s expense. All
parts must be returned freight prepaid to
Multiquip’s designated receiving point.
c. Any line item with an extended dealer
net price of less than $5.00.
7.
The sender will be notified of any material
received that is not acceptable.
8.
Such material will be held for five working
days from notification, pending instructions. If a reply is not received within five
days, the material will be returned to the
sender at his expense.
9.
Credit on returned parts will be issued at
dealer net price at time of the original
purchase, less a 15% restocking charge.
10. In cases where an item is accepted, for
which the original purchase document
can not be determined, the price will be
based on the list price that was effective
twelve months prior to the RMA date.
11. Credit issued will be applied to future
purchases only.
PRICING AND REBATES
Prices are subject to change without prior
notice. Price changes are effective on a specific date and all orders received on or after that
date will be billed at the revised price. Rebates
for price declines and added charges for price
increases will not be made for stock on hand
at the time of any price change.
PAGE 62 — MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06)
NOTE PAGE
MVC-88VGE/VGEW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (06/07/06) — PAGE 63
OPERATION & PARTS MANUAL
HERE'S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
UNITED STATES
Multiquip Corporate Office
18910 Wilmington Ave.
Tel. (800) 421-1244
Carson, CA 90746
Fax (800) 537-3927
Contact: mq@multiquip.com
Mayco Parts
800-306-2926
Fax: 800-672-7877
310-537-3700
Fax: 310-637-3284
Service Department
800-421-1244
Fax: 310-537-4259
310-537-3700
MQ Parts Department
800-427-1244
310-537-3700
MEXICO
UNITED KINGDOM
MQ Cipsa
Carr. Fed. Mexico-Puebla KM 126.5
Momoxpan, Cholula, Puebla 72760 Mexico
Contact: pmastretta@cipsa.com.mx
Tel: (52) 222-225-9900
Fax: (52) 222-285-0420
Fax: 800-672-7877
Fax: 310-637-3284
Warranty Department
800-421-1244, Ext. 279 Fax: 310-537-1173
310-537-3700, Ext. 279
Technial Assistance
800-478-1244
Fax: 310-631-5032
Multiquip (UK) Limited Head Office
Hanover Mill, Fitzroy Street,
Ashton-under-Lyne,
Lancashire OL7 0TL
Contact: sales@multiquip.co.uk
Tel: 0161 339 2223
Fax: 0161 339 3226
CANADA
BRAZIL
Multiquip
4110 Industriel Boul.
Laval, Quebec, Canada H7L 6V3
Contact: jmartin@multiquip.com
Multiquip
Av. Evandro Lins e Silva, 840 - grupo 505 Tel: 011-55-21-3433-9055
Barra de Tijuca - Rio de Janeiro
Fax: 011-55-21-3433-9055
Contact: cnavarro@multiquip.com.br, srentes@multiquip.com.br
Tel: (450) 625-2244
Fax: (450) 625-8664
© COPYRIGHT 2006, MULTIQUIP INC.
Multiquip Inc., Mikasa, and the MQ logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other
trademarks are the property of their respective owners and used with permission.
This manual MUST accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations are based on the MVC-88VGE/MVC-88VGEW
Plate Compactor. Illustrations, descriptions, references and technical data contained in this manual are for guidance only and may not be considered as binding. Multiquip
Inc. reserves the right to discontinue or change specifications, design or the information published in this publication at any time without notice and without incurring any
obligations.
Your Local Dealer is: