Allied Telesis AT FS708LE AT-FS708LE AT-FS708LE Installation guide

AT-FS708LE
10/100Base Ethernet Switch
Installation Guide
PN 613-50181-00 Rev A
Copyright  2001 Allied Telesyn International, Corp.
960 Stewart Drive Suite B, Sunnyvale CA USA 94085
All rights reserved. No part of this publication may be
reproduced without prior written permission from Allied
Telesyn International, Corp.
Ethernet is a registered trademark of Xerox Corporation. All
other product names, company names, logos or other
designations mentioned herein are trademarks or registered
trademarks of their respective owners.
Allied Telesyn International, Corp. reserves the right to
make changes in specifications and other information
contained in this document without prior written notice. The
information provided herein is subject to change without
notice. In no event shall Allied Telesyn International, Corp.
be liable for any incidental, special, indirect, or consequential
damages whatsoever, including but not limited to lost profits,
arising out of or related to this manual or the information
contained herein, even if Allied Telesyn International, Corp.
has been advised of, known, or should have known, the
possibility of such damages.
Electrical Safety and Emission
Statement
Standards: This product meets the following standards.
U.S. Federal Communications Commission
DECLARATION OF CONFORMITY
Manufacture Name:
Allied Telesyn International
Manufacture Address:
960 Stewart Drive, Suite B
Sunnyvale, CA 94086 USA
Manufacture Telephone:
408-730-0950
Declares that the product:
Ethernet switch
Model Number:
AT-FS708LE
This product complies with FCC Part 15, Class B Limits:
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device must not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
RADIATED ENERGY
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device pursuant to Part
15 of FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with instructions, may cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on. The user is
encouraged to try to correct the interference by one or more
of the following measures:
-
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and the
receiver.
iii
-
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
-
Consult the dealer or an experienced radio/TV technician
for help.
Changes and modifications not expressly approved by the
manufacturer or registrant of this equipment can void your
authority to operate this equipment under Federal
Communications Commission rules.
Industry Canada
This Class B digital apparatus meets all requirements of the
Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les
exigences du Règlement sur le matériel brouilleur du
Canada.
RFI Emission
FCC Part 15, EN55022,
C-Tick, CISPR 22, VCCI
1
(Class B)
WARNING: In a domestic environment this
product may cause radio interference in which
case the user may be required to take adequate
measures.
2
Immunity
EN55024
Electrical Safety
UL 1950, CSA C22.2
No. 950, EN60950
4
3
Important: Appendix A contains translated safety
statements for installing this equipment. When you see the
, go to Appendix A for the translated safety statement in
your language.
Wichtig: Anhang A enthält übersetzte Sicherheitshinweise
sehen,
für die Installation dieses Geräts. Wenn Sie
schlagen Sie in Anhang A den übersetzten Sicherheitshinweis
in Ihrer Sprache nach.
iv
Vigtigt: Tillæg A indeholder oversatte sikkerhedsadvarsler,
der vedrører installation af dette udstyr. Når De ser symbolet
, skal De slå op i tillæg A og finde de oversatte
sikkerhedsadvarsler i Deres eget sprog.
Belangrijk: Appendix A bevat vertaalde
veiligheidsopmerkingen voor het installeren van deze
ziet, raadpleeg Appendix A
apparatuur. Wanneer u de
voor vertaalde veiligheidsinstructies in uw taal.
Important: L'annexe A contient les instructions de sécurité
relatives à l'installation de cet équipement. Lorsque vous
, reportez-vous à l'annexe A pour
voyez le symbole
consulter la traduction de ces instructions dans votre langue.
Tärkeää: Liite A sisältää tämän laitteen asentamiseen
-symbolin, katso
liittyvät käännetyt turvaohjeet. Kun näet
käännettyä turvaohjetta liitteestä A.
Importante: l’Appendice A contiene avvisi di sicurezza
tradotti per l’installazione di questa apparecchiatura. Il
, indica di consultare l’Appendice A per l’avviso di
simbolo
sicurezza nella propria lingua.
Viktig: Tillegg A inneholder oversatt sikkerhetsinformasjon
, åpner du til
for installering av dette utstyret. Når du ser
Tillegg A for å finne den oversatte sikkerhetsinformasjonen
på ønsket språk.
Importante: O Anexo A contém advertências de segurança
traduzidas para instalar este equipamento. Quando vir o
, leia a advertência de segurança traduzida no seu
símbolo
idioma no Anexo A.
Importante: El Apéndice A contiene mensajes de seguridad
traducidos para la instalación de este equipo. Cuando vea el
, vaya al Apéndice A para ver el mensaje de
símbolo
seguridad traducido a su idioma.
Obs! Bilaga A innehåller översatta säkerhetsmeddelanden
,
avseende installationen av denna utrustning. När du ser
skall du gå till Bilaga A för att läsa det översatta
säkerhetsmeddelandet på ditt språk.
v
Table of Contents
Electrical Safety and Emission
Statement........................................................ iii
Table of Contents ......................................... vii
Welcome to Allied Telesyn .......................... ix
Where to Find Web-based Guides ................... ix
Document Conventions .................................... ix
Contacting Allied Telesyn ................................. x
Online Support ........................................... x
Telephone or Fax Support ........................ xi
E-mail Support ......................................... xii
Returning Products ......................................... xii
FTP Server...................................................... xiii
For Sales or Corporate Information .............. xiv
Tell Us What You Think ................................ xiv
AT-FS708LE Fast Ethernet Switch ............ 1
Overview ............................................................ 1
Features ............................................................. 2
Physical Description.......................................... 4
Ports 1 Through 7....................................... 4
Port 8 and the Uplink Port ........................ 5
Front Panel LEDs ...................................... 6
Power Supply.............................................. 7
Network Topologies ........................................... 8
vii
Installing the Unit........................................... 10
Verifying the Package Contents .............. 10
Selecting a Site ......................................... 11
Reviewing Safety Guidelines ................... 12
Installing the Unit on a Desktop ............. 14
Installing the Unit on a Wall................... 15
Verifying and Troubleshooting the
Installation....................................................... 17
Warranty Registration .................................... 19
Technical Specifications .................................. 19
Appendix A
Translated Safety and Emission
Information ................................................... 21
Appendix B
Technical Support Fax Order ................... 35
Incident Summary ........................................... 35
Appendix C
AT-FS708LE Installation Guide
Feedback ........................................................ 37
viii
Welcome to Allied Telesyn
This guide contains instructions on how to
install an Allied Telesyn AT-FS708LE Ethernet
Switch.
Where to Find Web-based Guides
The Allied Telesyn web site at
www.alliedtelesyn.com contains the most
recent documentation for all Allied Telesyn
products. All documents can be downloaded
from the web site in PDF format.
Document Conventions
This guide uses several conventions that you
should become familiar with before you begin to
install the product.
Note
A note provides additional information.
ix
Caution
A caution indicates that performing or
omitting a specific action may result in
equipment damage or loss of data.
Warning
A warning indicates that performing or
omitting a specific action may result in
bodily injury.
Contacting Allied Telesyn
You can contact Allied Telesyn technical
support by telephone, fax, e-mail, or online.
Online Support
You can request technical support online by
filling out the Online Technical Support Form
at www.alliedtelesyn.com/forms/
support.htm.
x
AT-FS708LE Installation Guide
Telephone or Fax Support
For technical support via fax, please fill out
the“Technical Support Fax Order” on page 35
and send it to the appropriate location listed
below.
Americas
United States, Canada,
Mexico, Central America,
South America
Tel:
1 (800) 428-4835
Fax:
1 (503) 639-3976
Germany
Germany, Switzerland,
Austria, Eastern Europe
Tel:
(+49) 30-435-900-126
Fax:
(+49) 30-435-70-650
Asia
Singapore, Taiwan, Thailand,
Malaysia, Indonesia, Korea,
Philippines, China,
India, Hong Kong
Tel:
(+65) 3815-612
Fax:
(+65) 3833-830
Italy
Italy, Spain, Portugal, Greece,
Turkey, Israel, Middle East,
Africa
Tel:
(+39) 02-41-30-41
Fax:
(+39) 02-41-30-42-00
Australia
Australia, New Zealand
Tel:
1 (800) 000-880
Fax:
(+61) 2-9438-4966
Japan
Tel:
(+81) 3-3443-5640
Fax:
(+81) 3-3443-2443
United Kingdom
France
France, Belgium, Luxembourg, United Kingdom, Denmark,
Norway, Sweden, Finland,
The Netherlands
Iceland
Tel:
(+33) 1-60-92-15-25
Tel:
(+44) 1-235-442560
Fax:
(+33) 1-69-28-37-49
Fax:
(+44) 1-235-442680
xi
E-mail Support
United States and Canada
TS1@alliedtelesyn.com
Latin America, Mexico, Puerto Rico,
Caribbean, and Virgin Islands
latin_america@alliedtelesyn.com
United Kingdom, Sweden, Norway,
Denmark, and Finland
support_europe@alliedtelesyn.com
Returning Products
Products for return or repair must first be
assigned a Return Materials Authorization
(RMA) number. A product sent to Allied
Telesyn without a RMA number will be
returned to the sender at the sender’s expense.
To obtain an RMA number, contact Allied
Telesyn’s Technical Support at one of the
following locations:
North America
2124 Zanker Road
San Jose, CA 95131
Tel: 1-800-428-4835,
option 4
Fax: 1-503-639-3716
xii
European Customer
Support Centre
10/11 Bridgemead Close
Westmead Industrial Estate
Swindon, Wiltshire SN5 7YT
England
Tel: +44-1793-501401
Fax: +44-1793-431099
AT-FS708LE Installation Guide
Latin America, the
Caribbean,
Virgin Islands
Tel: international code +
425-481-3852
Fax: international code +
425-483-9458
Mexico and Puerto Rico
Tel: 1-800-424-5012, ext 3852
or
1-800-424-4284, ext 385 2
Mexico only:
95-800-424-5012, ext 3852
Fax: international code +
425-489-9191
FTP Server
If you need a new version of management
software for an Allied Telesyn device and you
know the file name of the program, you can
download the software by connecting directly to
our FTP server at ftp://gateway.centre.com.
At login, enter ‘anonymous’. Enter your e-mail
address for the password as requested by the
server at login.
xiii
For Sales or Corporate Information
For sales or corporate information, contact
Allied Telesyn at one of the following locations:
Allied Telesyn
International, Corp.
19800 North Creek Parkway,
Suite 200
Bothell, WA 98011
Tel: 1 (425) 487-8880
Fax: 1 (425) 489-9191
Allied Telesyn
International, Corp.
960 Stewart Drive, Suite B
Sunnyvale, CA 94086
Tel: 1 (800) 424-4284 (USA
and Canada )
Fax: 1 (408) 736-0100
Tell Us What You Think
If you have any comments or suggestions on
how we might improve this or other Allied
Telesyn documents, please fill out the
“AT-FS708LE Installation Guide Feedback” on
page 37 and return the form to us at the
address or fax number provided. You can also
provide feedback online by filling out the Send
Us Feedback Form at
www.alliedtelesyn.com/forms/
feedback.htm.
xiv
AT-FS708LE Fast Ethernet
Switch
Overview
The AT-FS708LE unit is a 10Base-T/100BaseTX Ethernet switch. The unit provides you with
a simple, cost-effective solution for Ethernet
switching between end nodes operating at
either 10 or 100 Mbps.
1A
9-12V DC
100M
TX
/100BASE10BASE-T
8 PORT
CH
RNET SWIT
FAST ETHE
Power
Link/Act
Fdx
1
2
3
4
5
6
7
8
Figure 1 AT-FS708LE Ethernet Switch
1
Features
The AT-FS708LE Ethernet Switch has the
following features:
❑ Eight auto-negotiating 10/100 Mbps
twisted pair ports with RJ-45 connectors
❑ One Uplink port for connecting the
AT-FS708LE unit to a switch or hub
without a crossover cable
❑ IEEE 802.3 and IEEE 802.3u compliant
❑ 256K of buffer memory
❑ Store-and-forward packet forwarding
design
❑ Total bandwidth of up to 800 Mbps
❑ MAC address table capacity of 8,000
entries
❑ IEEE 802.3x flow control in full-duplex
operation and backpressure flow control
in half-duplex operation
❑ System and port status LEDs
❑ External power adapter
❑ Desktop or wall-mount installation
2
AT-FS708LE Installation Guide
Figure 2 and Figure 3 show the front and back
panels of the switch.
100M
10BASE-T/100BASE-TX 8 PORT FAST ETHERNET SWITCH
9-12V DC 1A
Link/Act
Power
Fdx
1
3
2
4
5
6
7
8
DC Power
Connector
Port LEDs
Figure 2 Front Panel
Uplink
8
7
6
5
4
3
2
1
Figure 3 Back Panel
3
Physical Description
The physical description for the switch
includes:
❑ Ports 1 through 7
❑ Port 8 and the Uplink port
❑ LEDs
❑ Power supply
Ports 1 Through 7
Ports 1 through 7 can operate at either 10 Mbps
or 100 speed and in either full- or half-duplex
mode. The ports, featuring RJ-45 connectors,
are configured as MDI-X, meaning that you can
connect a workstation or server to one of the
ports without using a crossover cable. The ports
have a maximum operating distance of 100
meters (328 feet) using Category 3, 4, or 5
shielded or unshielded twisted pair cable for 10
Mbps operation and Category 5 cable for 100
Mbps.
The ports are IEEE802.3u Auto-Negotiation
compliant. This means that the ports can
automatically configure their speed and duplex
mode to match the capabilities of the end nodes
connected to the ports.
4
AT-FS708LE Installation Guide
Port 8 and the Uplink Port
Port 8 and the Uplink port allow you to connect
an additional workstation to the unit or
interconnect the unit with a switch, hub, or
router, without the use of a crossover cable. If
you need to connect an additional workstation
to the unit, use Port 8, which is configured as
MDI-X, just like ports 1 through 7. If you need
to connect the unit to an Ethernet switch, hub,
or router, use the Uplink port, which is
configured as MDI.
Both Port 8 and the Uplink port offer 10 Mbps
or 100 Mbps performance and auto-negotiation
operation for both speed and duplex mode, just
like ports 1 through 7. Both ports feature an
RJ-45 connector and have a maximum
operating distance of 100 meters (328 feet)
using Category 3, 4, or 5 twisted pair cable for
10 Mbps operation and Category 5 cable for 100
Mbps operation.
Note
You can use either port 8 or the Uplink
port. You cannot use both
simultaneously.
5
Front Panel LEDs
Refer to Table 1 for a description of the device
LEDs.
Table 1 LED Functions
LEDs
Color
Description
Power
Green
On means the switch is
receiving power.
Off means the switch is not
receiving power.
100M
Green
On means the port is
operating at 100 Mbps.
Yellow
On means the port is
operating at 10 Mbps.
Green
On indicates a valid physical
link on the port.
Flashing indicates data is
being transmitted or received
on the port.
Off means there is no link on
the port.
Link/Act
6
AT-FS708LE Installation Guide
Table 1 LED Functions (continued)
LEDs
Color
Description
Fdx/Hdx
Green
On indicates the port is
operating in full-duplex
mode.
Off indicates the port is
operating in half-duplex
mode.
Power Supply
The AT-FS708LE Ethernet Switch uses an
external power adapter that comes standard
with the unit.
7
Network Topologies
Figure 4 illustrates a network that consists of
one AT-FS708LE Ethernet Switch used to
interconnect seven workstations and a server.
The Uplink port is not used in this
configuration.
Uplink
8
7
6
5
4
3
2
1
Figure 4 Single AT-FS708LE Topology
8
AT-FS708LE Installation Guide
Figure 5 illustrates a network of two ATFS708LE Ethernet Switches that have been
interconnected using the Uplink port on the top
unit. Using the Uplink port eliminates the need
for a crossover cable to interconnect the devices.
Uplink
Uplink
8
8
7
7
6
6
5
5
4
4
3
2
3
2
1
1
Figure 5 Multiple AT-FS708LE Ethernet Switch
Topology
9
Installing the Unit
This section contains the procedures for
installing the unit.
Verifying the Package Contents
Make sure that the package includes the
following items. If any item is damaged or
missing, contact your Allied Telesyn
representative for assistance.
❑ One AT-FS708LE Ethernet Switch
❑ One power adapter
❑ Four self-adhesive rubber feet
❑ Warranty card
❑ This installation guide
Note
For wall-mount installation, you must
supply the two screws and plastic
anchors or other material necessary to
physically mount the switch to the wall.
10
AT-FS708LE Installation Guide
Selecting a Site
Be sure to observe the following site
requirements:
❑ Make sure you are placing the device in a
dust-free and moisture-free environment.
❑ Do not block the ventilation openings on
the unit. Allow at least 10 centimeters (4
inches) of space at the front and back of
the unit for ventilation.
❑ Make sure that the unit’s power is
accessible and cables can be connected
easily.
❑ Cabling should be away from sources of
electrical noise such as radios,
transmitters, broadband amplifiers,
power lines, and fluorescent fixtures.
❑ Do not place objects on top of the unit.
❑ Use dedicated power circuits or power
conditioners to supply power to the unit.
11
❑ Observe the following cabling
specifications:
Ports
Connector
Type
1 to 8
RJ-45
Type of Cable
Maximum
Distance
Category 3, 4,
or 5 (10 Mbps)
100 m
(328 ft)
Category 5
(100 Mbps)
Uplink
RJ-45
Category 3, 4,
or 5 (10 Mbps)
100 m
(328 ft)
Category 5
(100 Mbps)
Reviewing Safety Guidelines
Please review the following safety guidelines
before you begin to install the device.
Warning
Power cord is used as a
disconnection device: To deenergize equipment, disconnect the
power cord.
5
12
AT-FS708LE Installation Guide
Caution
Pluggable Equipment: The socket
outlet should be installed near the
equipment and should be easily
accessible.
6
Caution
Air vents: The air vents on the unit must
not be blocked and must have free access
to the room ambient air for cooling.
7
Caution
Operating Temperature: This product
is designed for a maximum ambient
temperature of 40°C.
8
Caution
All Countries: Install this product in
accordance with local and National
Electric Codes.
9
Caution
EUROPE - EU: Use TÜV licensed AC
adapter of DC 9V, 1A.
10
Caution
USA/CANADA: Use a UL Listed/CSA
Certified AC adapter of DC 9V, 1A.
11
13
Installing the Unit on a Desktop
To install the switch on the desktop, perform
the following procedure. To mount the unit on a
wall, perform the steps “Installing the Unit on a
Wall” on page 15.
1. Attach the four self-adhesive rubber feet to
the bottom of the device, positioning them in
the indentations.
2. Place the device on a flat, level surface.
3. Plug the power adapter into a power source
and then plug the DC power cord into the DC
connector on the front panel of the switch.
Warning
The power cord is used as a
disconnection device. To de-energize
equipment, disconnect the power cord.
5
4. Make sure the Power LED on the front panel
lights green.
14
AT-FS708LE Installation Guide
5. Attach the data cables to the ports on the hub.
Do not use crossover cables to connect
workstations or servers to ports 1 through 8.
Do not use a crossover cable to connect a
switch, hub, or router to the Uplink port.
Note
You can use either port 8 or the Uplink
port on an AT-FS708LE device. You
cannot use both ports simultaneously.
6. Go to the procedure “Verifying and
Troubleshooting the Installation” on page 17.
Installing the Unit on a Wall
For wall-mount installation, you can position
the switch vertically or horizontally on the wall
using the keyhole cutouts in the bottom of the
switch chassis.
1. If previously attached, remove the rubber feet
and all cables and the DC power cord from the
switch.
2. Select a wall location for the switch.
15
Note
For wall-mount installation, you must
supply the two screws and plastic
anchors or other material necessary to
physically mount the switch to the wall.
3. Install two plastic anchors and two pan-head
screws into the wall, separated by 5
centimeters (approximately 2 inches).
4. Position the device onto the wall screws.
5. Plug the power adapter into a power source
and plug the DC power cord into the DC
connector on the front panel of the switch.
Warning
The power cord is used as a
disconnection device. To de-energize
equipment, disconnect the power cord.
5
6. Make sure the Power LED on the front panel
lights green.
16
AT-FS708LE Installation Guide
7. Attach the data cables to the switch ports. Do
not use crossover cables to connect
workstations or servers to ports 1 through 8.
Do not use a crossover cable to connect a
switch, hub, or router to the Uplink port.
Note
You can use either port 8 or the Uplink
port, but you cannot use both
simultaneously.
8. Go to the procedure “Verifying and
Troubleshooting the Installation” on page 17.
Verifying and Troubleshooting the
Installation
The following procedure should be perform
after you have initially installed the unit to
check to be sure that the device is operating
properly. You can also perform this procedure
to troubleshoot the unit in the event you
experience any problems with the device.
1. Check the Power LED. The LED should be
ON. If the LED is OFF, check the following:
❑ Verify that the power adapter is securely
connected to the power source and to the
DC connector on the front of the ATFS708LE unit.
17
❑ Check to be sure that the power outlet has
power by connecting another device to it.
❑ Try replacing the power adapter with
another power adapter.
2. Check the Link/Act LED for each port. The
LED should be lit steady or flashing. If a
Link/Act LED is OFF, check the following:
❑ Verify that the node connected to the port
on the switch is powered ON. If the node
is OFF, power the unit ON.
❑ Verify that the distance between the
switch and the connected network device
is no greater than 100 meters (328 feet).
❑ Check to be sure that you are using the
correct type of cable: Category 3, 4, or 5 for
10 Mbps operation and Category 5 cable
for 100 Mbps operation.
❑ Verify that the cable has not been cut or
damaged.
3. If the Lnk/Act LED for a port is ON but there
is a communication problem to the end node
connected to the port, such as the loss of data,
check the following:
❑ Check to be sure that the distance
between the switch and the connected
network device is no greater than 100
meters (328 feet).
18
AT-FS708LE Installation Guide
❑ Verify that you are using the correct type
of cable: Category 3, 4, or 5 for 10 Mbps
operation and Category 5 cable for 100
Mbps operation.
Warranty Registration
When you have finished installing the unit, you
should register your product by completing the
enclosed warranty card and sending it in, or by
visiting our web site at
www.alliedtelesyn.com/forms/
warranty.htm and completing the on-line
registration.
Technical Specifications
Standards Compatibility:
IEEE 802.3,
IEEE802.3u
Power Supply:
Input: 9V @ 1A
Connectors:
RJ-45
Address Table:
8,000 entries total
Queue Buffer:
256K bytes
19
Flow Control:
Full-duplex:
Disable IEEE
803.3u
Half-duplex:
Enable
backpressure
Physical Dimensions:
WxDxH
146 x 82 x 26 mm
(5.75 x 3.23 x 1.02
in.)
Environment Specifications:
Operating Temperature 0° to 40° C
Storage Temperature
-25° to 70° C
Operating Humidity
5% to 90%
Relative Humidity
Storage Humidity
10% to 95%
Relative Humidity
Electromagnetic Emission: FCC Part 15,
EN55022,
C-Tick, CISPR 22,
VCCI (Class B)
Certification:
CE Mark
Immunity:
EN55024
Safety:
UL 1950, CSA
C22.2 No. 950,
EN60950
20
Appendix A
Translated Safety and
Emission Information
Important: This appendix contains multiplelanguage translations for the safety statements
in this guide.
Wichtig: Dieser Anhang enthält
Übersetzungen der in diesem Handbuch
enthaltenen Sicherheitshinweise in mehreren
Sprachen.
Vigtigt: Dette tillæg indeholder oversættelser i
flere sprog af sikkerhedsadvarslerne i denne
håndbog.
Belangrijk: Deze appendix bevat vertalingen
in meerdere talen van de
veiligheidsopmerkingen in deze gids.
Important: Cette annexe contient la traduction
en plusieurs langues des instructions de
sécurité figurant dans ce guide.
Tärkeää: Tämä liite sisältää tässä oppaassa
esiintyvät turvaohjeet usealla kielellä.
21
Importante: questa appendice contiene
traduzioni in più lingue degli avvisi di sicurezza
di questa guida.
Viktig: Dette tillegget inneholder oversettelser
til flere språk av sikkerhetsinformasjonen i
denne veiledningen.
Importante: Este anexo contém traduções em
vários idiomas das advertências de segurança
neste guia.
Importante: Este apéndice contiene
traducciones en múltiples idiomas de los
mensajes de seguridad incluidos en esta guía.
Obs! Denna bilaga innehåller flerspråkiga
översättningar av säkerhetsmeddelandena i
denna handledning.
22
AT-FS708LE Installation Guide
Standards: This product meets the following standards:
U.S. Federal Communications Commission
DECLARATION OF CONFORMITY
Manufacture Name:
Allied Telesyn International
Manufacture Address:
950 Stewart Drive, Suite B
Sunnyvale, CA 94085 USA
408-730-0950
Manufacture Telephone:
Declares that the product:
Ethernet switch
Model Number:
AT-FS708LE
This product complies with FCC Part 15, Class B Limits:
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device must not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
RADIATED ENERGY
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device pursuant to Part
15 of FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with instructions, may cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on. The user is
encouraged to try to correct the interference by one or more
of the following measures:
-
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the
receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician
for help.
Changes and modifications not expressly approved by the
manufacturer or registrant of this equipment can void your
authority to operate this equipment under Federal
Communications Commission rules.
23
Industry Canada
This Class B digital apparatus meets all requirements of the
Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les
exigences du Règlement sur le matériel brouilleur du
Canada.
24
1
RFI Emissions
2
WARNING: In a domestic environment this
product may cause radio interference in which
case the user may be required to take adequate
measures.
3
Immunity
EN55024
4
Electrical Safety
UL 1950, CSA C22.2
No. 950, EN60950
FCC Part 15,
EN55022, C-Tick,
CISPR 22, VCCI
(Class B)
SAFETY
5
CAUTION: POWER CORD IS USED AS A
DISCONNECTION DEVICE. TO DE-ENERGIZE
EQUIPMENT, disconnect the power cord.
6
PLUGGABLE EQUIPMENT, the socket outlet
shall be installed near the equipment and shall be
easily accessible.
7
CAUTION: Air vents must not be blocked and
must have free access to the room ambient air for
cooling.
8
OPERATING TEMPERATURE: This product is
designed for a maximum ambient temperature of
40° degrees C.
9
ALL COUNTRIES: Install product in accordance
with local and National Electrical Codes.
10
EUROPE - EU: Use TÜV licensed AC adapter of
DC 7.5V, 1A.
AT-FS708LE Installation Guide
11
USA/CANADA: Use a UL Listed/CSA Certified
AC adapter of DC 9V, 1A.
Normen: Dieses Produkt erfüllt die
Anforderungen der nachfolgenden Normen.
1
Hochfrequenzstörung
2
WARNUNG: Bei Verwendung zu Hause kann
dieses Produkt Funkstörungen hervorrufen. In
diesem Fall müßte der Anwender angemessene
Gegenmaßnahmen ergreifen.
3
Störsicherheit
EN55024
4
Elektrische Sicherheit
UL 1950, CSA C22.2
No. 950, EN60950
FCC Part 15,
EN55022, C-Tick,
CISPR 22, VCCI
(Class B)
SICHERHEIT
5
VORSICHT: DAS NETZKABEL DIENT ZUM
TRENNEN DER STROMVERSORGUNG. ZUR
TRENNUNG VOM NETZ, KABEL AUS DER
STECKDOSE ZIEHEN.
6
STECKBARES GERÄT: Die Anschlußbuchse
sollte in der Nähe der Einrichtung angebracht
werden und leicht zugänglich sein."
7
VORSICHT
Die Entlüftungsöffnungen dürfen nicht versperrt
sein und müssen zum Kühlen freien Zugang zur
Raumluft haben.
8
BETRIEBSTEMPERATUR: Dieses Produkt
wurde für den Betrieb in einer
Umgebungstemperatur von nicht mehr als 40° C
entworfen.
9
ALLE LÄNDER: Installation muß örtlichen und
nationalen elektrischen Vorschriften entsprechen.
10
Gebrauchen Sie einen von TÜV zugelassenen
Wechselstromadapter für Gleichstrom 9 V, 1A.
25
26
Standarder: Dette produkt tilfredsstiller de
følgende standarder.
1
Radiofrekvens
forstyrrelsesemission:
FCC Part 15,
EN55022, C-Tick,
CISPR 22, VCCI
(Class B)
2
ADVARSEL: I et hjemligt miljø kunne dette
produkt forårsage radio forstyrrelse. Bliver det
tilfældet, påkræves brugeren muligvis at tage
tilstrækkelige foranstaltninger.
3
Immunitet
EN55024
4
Elektrisk sikkerhed
UL 1950, CSA C22.2
No. 950, EN60950
SIKKERHED
5
ADVARSEL: DEN STRØMFØRENDE
LEDNING BRUGES TIL AT AFBRYDE
STRØMMEN. SKAL STRØMMEN TIL
APPARATET AFBRYDES, tages ledningen ud af
stikket.
6
UDSTYR TIL STIKKONTAKT, stikkontakten bør
installeres nær ved udstyret og skal være
lettilgængelig.
7
ADVARSEL: Ventilationsåbninger må ikke
blokeres og skal have fri adgang til den omgivende
luft i rummet for afkøling.
8
BETJENINGSTEMPERATUR: Dette apparat
er konstrueret til en omgivende temperatur på
maksimum 40 grader C.
9
ALLE LANDE: Installation af produktet skal ske
i overensstemmelse med lokal og national
lovgivning for elektriske installationer.
10
Brug kun TÜV godkendt
vekselstrømstransformator på 9 V jævnstrøm,
1A.
AT-FS708LE Installation Guide
Eisen: Dit product voldoet aan de volgende eisen.
1
RFI Emissie
2
WAARSCHUWING: Binnenshuis kan dit
product radiostoring veroorzaken, in welk geval
de gebruiker verplicht kan worden om gepaste
maatregelen te nemen.
3
Immuniteit
4
Electrische Veiligheid
FCC Part 15, EN55022,
C-Tick, CISPR 22, VCCI
(Class B)
EN55024
UL 1950, CSA C22.2 No.
950, EN60950
VEILIGHEID
5
WAARSCHUWING: HET TOESTEL WORDT
UITGESCHAKELD DOOR DE STROOMKABEL
TE ONTKOPPELEN.OM HET TOESTEL
STROOMLOOS TE MAKEN: de stroomkabel
ontkoppelen.
6
AAN TE SLUITEN APPARATUUR, de
contactdoos wordt in de nabijheid van de
apparatuur geïnstalleerd en is gemakkelijk te
bereiken."
7
OPGELET: De ventilatiegaten mogen niet
worden gesperd en moeten de omgevingslucht
ongehinderd toelaten voor afkoeling.
8
BEDRIJFSTEMPERATUUR: De
omgevingstemperatuur voor dit produkt mag niet
meer bedragen dan 40 graden Celsius.
9
ALLE LANDEN: het toestel installeren
overeenkomstig de lokale en nationale elektrische
voorschriften.
10
Gebruik een door TÜV gekeurde
wisselstroomadapter van 9 Volt gelijkstroom, 1
ampères.
27
28
Normes: ce produit est conforme aux normes de
suivantes.
1
Emission d’interférences
radioélectriques
FCC Part 15,
EN55022, C-Tick,
CISPR 22, VCCI
(Class B)
2
MISE EN GARDE : dans un environnement
domestique, ce produit peut provoquer des
interférences radioélectriques. Auquel cas,
l’utilisateur devra prendre les mesures adéquates.
3
Immunité
EN55024
4
Sécurité électrique
UL 1950, CSA C22.2
No. 950, EN60950
5
DANGER DE FOUDRE
DANGER: NE PAS MANIER le matériel ou les
CÂBLES lors d’activité orageuse.
6
EQUIPEMENT POUR BRANCHEMENT
ELECTRIQUE, la prise de sortie doit être placée
près de l’équipement et facilement accessible".
7
ATTENTION: Ne pas bloquer les fentes
d’aération, ceci empêcherait l’air ambiant de
circuler librement pour le refroidissement.
8
TEMPÉRATURE DE FONCTIONNEMENT:
Ce matériel est capable de tolérer une
température ambiante maximum de ou 40 degrés
Celsius.
9
POUR TOUS PAYS: Installer le matériel
conformément aux normes électriques nationales
et locales.
10
Utiliser un adaptateur secteur conforme TÜV
de 9 V, 1 A en courant continu.
AT-FS708LE Installation Guide
Standardit: Tämä tuote on seuraavien
standardien mukainen.
1
Radioaaltojen häirintä
2
VAROITUS: Kotiolosuhteissa tämä laite voi
aiheuttaa radioaaltojen häiröitä, missä
tapauksessa laitteen käyttäjän on mahdollisesti
ryhdyttävä tarpeellisiin toimenpiteisiin.
3
Kestävyys
EN55024
4
Sähköturvallisuus
UL 1950, CSA C22.2
No. 950, EN60950
FCC Part 15,
EN55022, C-Tick,
CISPR 22, VCCI
(Class B)
TURVALLISUUS
5
HUOMAUTUS: VIRTAJOHTOA KÄYTETÄÄN
VIRRANKATKAISULAITTEENA. VIRTA
KATKAISTAAN irrottamalla virtajohto.
6
PISTORASIAAN KYTKETTÄVÄ LAITE;
pistorasia on asennettava laitteen lähelle ja
siihen on oltava esteetön pääsy."
7
HUOMAUTUS: Ilmavaihtoreikiä ei pidä tukkia
ja niillä täytyy olla vapaa yhteys ympäröivään
huoneilmaan, jotta ilmanvaihto tapahtuisi.
8
KÄYTTÖLÄMPÖTILA: Tämä tuote on
suunniteltu ympäröivän ilman
maksimilämpötilalle 40°C.
9
KAIKKI MAAT: Asenna tuote paikallisten ja
kansallisten sähköturvallisuusmääräysten
mukaisesti.
10
Käytä TÜV-lisenssillä valmistettua
verkkosovitinta, jonka tasajännitteen
nimellisarvot ovat DC 9 V, 1 A (ampeeria).
29
30
Standard: Questo prodotto è conforme ai
seguenti standard.
1
Emissione RFI (interferenza di
radiofrequenza)
FCC Part 15,
EN55022, C-Tick,
CISPR 22, VCCI
(Class B)
2
AVVERTENZA: in ambiente domestico questo
prodotto potrebbe causare radio interferenza. In
questo caso potrebbe richiedersi all’utente di
prendere gli adeguati provvedimenti.
3
Immunità
EN55024
4
Sicurezza elettrica
UL 1950, CSA C22.2
No. 950, EN60950
NORME DI SICUREZZA
5
ATTENZIONE: IL CAVO DI ALIMENTAZIONE
È USATO COME DISPOSITIVO DI
DISATTIVAZIONE. PER TOGLIERE LA
CORRENTE AL DISPOSITIVO staccare il cavo di
alimentazione.
6
APPARECCHIATURA COLLEGABILE, la presa
va installata vicino all’apparecchio per risultare
facilmente accessibile".
7
ATTENZIONE: le prese d’aria non vanno
ostruite e devono consentire il libero ricircolo
dell’aria ambiente per il raffreddamento.
8
TEMPERATURA DI FUNZIONAMENTO:
Questo prodotto è concepito per una temperatura
ambientale massima di 40 gradi centigradi.
9
TUTTI I PAESI: installare il prodotto in
conformità delle vigenti normative elettriche
nazionali.
10
Utilizzare l’adattatore per c.a. da 9 V c.c. e 1 A
conforme alla normativa TÜV.
AT-FS708LE Installation Guide
Sikkerhetsnormer: Dette produktet
tilfredsstiller følgende sikkerhetsnormer.
1
RFI stråling
2
ADVARSEL: Hvis dette produktet benyttes til
privat bruk, kan produktet forårsake
radioforstyrrelse. Hvis dette skjer, må brukeren
ta de nødvendige forholdsregler.
3
Immunitet
EN55024
4
Elektrisk sikkerhet
UL 1950, CSA C22.2
No. 950, EN60950
FCC Part 15,
EN55022, C-Tick,
CISPR 22, VCCI
(Class B)
SIKKERHET
5
FORSIKTIG: STRØMLEDNINGEN BRUKES
TIL Å FRAKOBLE UTSTYRET. FOR Å
DEAKTIVISERE UTSTYRET, må
strømforsyningen kobles fra.
6
UTSTYR FOR STIKKONTAKT. Stikkontakten
skal monteres i nærheten av utstyret og skal være
lett tilgjengelig."
7
FORSIKTIG: Lufteventilene må ikke blokkeres,
og må ha fri tilgang til luft med romtemperatur
for avkjøling.
8
DRIFTSTEMPERATUR: Dette produktet er
konstruert for bruk i maksimum romtemperatur
på 40 grader celsius.
9
ALLE LAND: Produktet må installeres i samsvar
med de lokale og nasjonale elektriske koder.
10
Benytt TÜV-godkjent AC-adapter på 9V DC, 1A
(milliampere).
31
32
Padrões: Este produto atende aos seguintes
padrões.
1
Emissão de interferência de
radiofrequência
FCC Part 15,
EN55022, C-Tick,
CISPR 22, VCCI
(Class B)
2
AVISO: Num ambiente doméstico este produto
pode causar interferência na radiorrecepção e,
neste caso, pode ser necessário que o utente tome
as medidas adequadas.
3
Imunidade
EN55024
4
Segurança Eléctrica
UL 1950, CSA C22.2
No. 950, EN60950
SEGURANÇA
5
CUIDADO: O CABO DE ALIMENTAÇÃO É
UTILIZADO COMO UM DISPOSITIVO DE
DESCONEXÃO. PARA DESELETRIFICAR O
EQUIPAMENTO, desconecte o cabo de
ALIMENTAÇÃO.
6
EQUIPAMENTO DE LIGAÇÃO, a tomada
eléctrica deve estar instalada perto do
equipamento e ser de fácil acesso."
7
CUIDADO: As aberturas de ventilação não
devem ser bloqueadas e devem ter acesso livre ao
ar ambiente para arrefecimento adequado do
aparelho.
8
TEMPERATURA DE FUNCIONAMENTO:
Este produto foi projetado para uma temperatura
ambiente máxima de 40 graus centígrados.
9
TODOS OS PAÍSES: Instale o produto de acordo
com as normas nacionais e locais para instalações
elétricas.
10
Use um adaptador de corrente alternada com
saída DC de 9V e 1A em conformidade com as
especificações da TÜV.
AT-FS708LE Installation Guide
Estándares: Este producto cumple con los
siguientes estándares.
1
Emisión RFI
2
ADVERTENCIA: en un entorno doméstico, este
producto puede causar radiointerferencias, en
cuyo caso, puede requerirse del usuario que tome
las medidas que sean convenientes al respecto.
3
Inmunidad
EN55024
4
Seguridad eléctrica
UL 1950, CSA C22.2
No. 950, EN60950
FCC Part 15,
EN55022, C-Tick,
CISPR 22, VCCI
(Class B)
SEGURIDAD
5
ATENCION: EL CABLE DE ALIMENTACION
SE USA COMO UN DISPOSITIVO DE
DESCONEXION. PARA DESACTIVAR EL
EQUIPO, desconecte el cable de alimentación.
6
EQUIPO CONECTABLE, el tomacorriente se
debe instalar cerca del equipo, en un lugar con
acceso fácil".
7
ATENCION: Las aberturas para ventilación no
deberán bloquearse y deberán tener acceso libre al
aire ambiental de la sala para su enfriamiento.
8
TEMPERATURA REQUERIDA PARA LA
OPERACIÓN: Este producto está diseñado para
una temperatura ambiental máxima de 40 grados
C.
9
PARA TODOS LOS PAÍSES: Monte el producto
de acuerdo con los Códigos Eléctricos locales y
nacionales.
10
Utilizar un adaptador de corriente alterna
autorizado TÜV de 9 voltios de corriente continua
y 1 amperios.
33
34
Standarder: Denna produkt uppfyller följande
standarder.
1
Radiostörning
2
VARNING: Denna produkt kan ge upphov till
radiostörningar i hemmet, vilket kan tvinga
användaren till att vidtaga erforderliga åtgärder.
3
Immunitet
EN55024
4
Elsäkerhet
UL 1950, CSA C22.2
No. 950, EN60950
FCC Part 15,
EN55022, C-Tick,
CISPR 22, VCCI
(Class B)
SÄKERHET
5
VARNING: NÄTKABELN ANVÄNDS SOM
STRÖMBRYTARE FÖR ATT KOPPLA FRÅN
STRÖMMEN, dra ur nätkabeln.
6
UTRUSTNING MED PLUGG. Uttaget skall
installeras i utrustningens närhet och vara
lättåtkomligt".
7
VARNING: Luftventilerna får ej blockeras och
måste ha fri tillgång till omgivande rumsluft för
avsvalning.
8
DRIFTSTEMPERATUR: Denna produkt är
konstruerad för rumstemperatur ej överstigande
40 grader Celsius.
9
ALLA LÄNDER: Installera produkten i enlighet
med lokala och statliga bestämmelser för
elektrisk utrustning.
10
Använd en växelströmsanslutningsenhet
licensierad av TÜV.Likström 9V, 1A.
Appendix B
Technical Support Fax Order
Name __________________________________
Company _______________________________
Address ________________________________
City____________________________________
State/Province __________________________
Zip/Postal Code ________________________
Country ________________________________
Phone __________________________________
Fax ___________________________________
Incident Summary
Model number of Allied Telesyn product
I am using______________________________
Firmware release number of Allied Telesyn
product ________________________________
Other network software products I am using
(e.g., network managers) ________________
_______________________________________
35
Brief summary of problem _______________
_______________________________________
Conditions (List the steps that led up
to the problem. _________________________
_______________________________________
_______________________________________
Detailed description (Please use separate sheet)
Please also fax printouts of relevant files such as
batch files and configuration files. When
completed, fax this sheet to the appropriate
Allied Telesyn office. Fax numbers can be found
on page x.
36
Appendix C
AT-FS708LE Installation Guide
Feedback
Please tell us what additional information you
would like to see discussed in this guide. You
can fax or mail this form to the mailing address
and fax number at the bottom of the page.
I found the following the most valuable _______
___________________________________________
___________________________________________
I would like the following more developed _____
___________________________________________
___________________________________________
I would find this guide more useful if _________
___________________________________________
___________________________________________
Allied Telesyn International, Corp.
c/o Technical Communications
960 Stewart Drive, Suite B
Sunnyvale, CA 94085 USA
PN 613-50181-00 Rev A
37