THE WALL-MOUNT™ 6-TON AIR CONDITIONERS

THE WALL-MOUNT™ 6-TON AIR CONDITIONERS
Model W70A - Right Side Control Panel
Model W70L - Left Side Control Panel
68,000 Btuh
9.5 EER
60Hz
GREEN REFRIGERANT
R-410A
The Bard Wall-Mount Air Conditioner is a self contained energy efficient
system, which is designed to offer maximum indoor comfort at a minimal
cost without using valuable indoor floor space or outside ground space.
This unit is the ideal product for versatile applications such as: new
construction, modular offices, school modernization, telecommunication
structures, portable structures or correctional facilities. Factory or field
installed accessories are available to meet specific job requirements.
Engineered Features
Aluminum Finned Copper Coils:
Grooved tubing and enhanced louvered
fin for maximum heat transfer and
energy efficiency.
Twin Blowers:
Move air quietly. Most models feature
multispeed blower motors providing
airflow adjustment for high and low
static operation. Motor overload
protection is standard on all models.
Air Conditioner Compressor:
Scroll Compressors eliminate need for
crankcase heater.
R-410A Refrigerant:
Designed with R-410A (HFC) nonozone depleting refrigerant in
compliance with the Montreal protocol
and 2010 EPA requirements.
Phase Rotation Monitor:
Standard on all 3 phase scroll
compressors. Protects against reverse
rotation if power supply is not properly
connected.
Galvanized 20 Gauge Zinc Coated
Steel Cabinet:
Cleaned, rinsed, sealed and dried
before the polyurethane primer is
applied. The cabinet is handsomely
finished with a baked on textured
enamel, which allows it to withstand
1000 hours of salt spray tests per
ASTM B117-03.
Foil Faced Insulation:
Standard on all units.
Full Length Mounting Brackets:
Built into cabinet for improved
appearance and easy installation.
NOTE: Bottom mounting bracket
included to assist in installation.
Electrical Components:
Are easily accessible for routine
inspection and maintenance through a
left side, service panel opening.
Features a lockable, hinged access
cover to the circuit breaker or toggle
disconnect switch.
Electric Heat Strips:
Features an automatic limit and thermal
cut-off safety control. Heater packages
can be factory installed for all 1½ through
5 ton models.
Filter Service Door:
Separate service door provides easy
access for filter change.
MEA # 357-93-E
One Inch, Disposable Air Filters:
Are standard equipment. Optional one
inch washable filters available and filter
racks permit the addition of 2" pleated
filter. Factory or field installed.
Condenser Fan and Motor
Shroud Assembly:
Slides out for easy access.
Liquid Line Filter Drier:
Standard on all units. Protects system
against moisture.
Barometric Fresh Air Damper:
Standard on all units. Allows up to 25%
outside fresh air. Optional ventilation
packages available.
Compressor Control Module:
Standard on all units. Built-in off-delay
timer adjustable from 30 seconds to 5
minutes. 2-minute on-delay if power
interrupt. 120-second bypass for low
pressure control, and both soft and
manual lockouts for high and low
pressure controls. Alarm output for
alarm relay.
Built-in Circuit Breakers:
Standard on all electric heat versions of
single (230/208 volt) and three phase
(230/208 volt) equipment. Toggle
disconnects are standard on all electric
heat versions of three phase (460 volt)
equipment.
Slope Top:
Standard feature for water run-off.
Top Rain Flashing:
Standard feature on all models.
High & Low Pressure Switches are
Auto-Reset:
Standard on all units. Built-in lockout
circuit resets from the room thermostat.
Provides commercial quality protection to
the compressor.
• Complies with efficiency requirements of ANSI/ASHRAE/IESNA 90.1-2007.
• Certified to ANSI/ARI Standard 390-2003 for SPVU (Single Package Vertical Units).
• Intertek ETL Listed to Standard for Safety Heating and Cooling Equipment ANSI/UL
1995/CSA 22.2 No. 236-05, Third Edition.
• Commercial Product - Not intended for Residential application.
Form No.
S3409-510
Supersedes S3409-1009
Page
1 of 8
Capacity and Efficiency Ratings
Models
Volts
Operating
Voltage Range
Compressor
Type
P h ase
Cooling
C ap . B T U H 1
C FM / E S P
(Rated — Wet Coil)
EER 2
W70A1-A, W70L1-A
230/208
197 - 253
SCROLL
1
68,000
1,800 / .2
9.5
W70A1-B, W70L1-B
230/208
197 - 253
SCROLL
3
68,000
1,800 / .2
9.5
W70A1-C, W70L1-C
460
414 - 506
SCROLL
3
68,000
1,800 / .2
9.5
1 Capacity is certified in accordance with ANSI/ARI Standard 390-2003.
2 EER = Energy Efficiency Ratio and is certified in accordance with ANSI/ARI Standard 390-2003.
All ratings based on fresh air intake being 100% closed (no outside air introduction).
Specifications
Models
Electrical
Rating — 60 HZ
R LA
Compressor
B C SC
LR A
W70A1-A, W70L1-A
230/208-1
26.9 / 31
31
145
W70A1-B, W70L1-B
230/208-3
23 / 26.6
26.6
W70A1-C, W70L1-C
460-3
14.1
14.1
Outdoor Fan Motor
H P / R PM / SPD
FLA DIA / CFM
1/2 / 1075 / 1-Spd
4.0
24" / 3,500
160
1/2 / 1075 / 1-Spd
4.0
87
3/4 / 1075 / 1-Spd
1.7
Indoor Blow er Motor
H P / R PM / SPD
FLA
Filter Siz e Shipping
(Inches) Std. Weight
1/2 / 1,070 / 2-Spd.
3.3
20 x 30 x 1
575
24" / 3,500
1/2 / 1,070 / 2-Spd
3.3
20 x 30 x 1
575
24" / 3,500
1/2 / 1,070 / 2-Spd
1.9
20 x 30 x 1
575
IMPORTANT — While this electrical data is presented as a guide, it is important to electrically connect properly sized fuses and conductor wires in accordance with the National
Electrical Code and all existing local codes.
Electrical Specifications
SINGLE CIRCUIT
1 Maximum
Rated
N o.
3
External
Volts
Field
Minimum
F u se
&
P o w er
Circuit
or Circuit
Phase Circuits
Ampacity
Breaker
MODELS
DUAL CIRCUIT
2 Field
P o w er
Wire
Siz e
1 Maximum
2
3 Minimum
External
Ground
Circuit
F u se
Wire
Ampacity
or Circuit
Siz e
Breaker
2 Field
P o w er
Wire Siz e
2 Ground
Wire
Siz e
Ckt. A Ckt. B Ckt. A Ckt. B Ckt. A Ckt. B Ckt. A Ckt. B
W70A1-A00, A0Z / W70L1-A00, A0Z
W70A1-A05 / W70L1-A05
W70A1-A10 / W70L1-A10
230/208-1
W70A1-A15 / W70L1-A15
W70A1-A20
W70A1-B00, B0Z / W70L1-B00, B0Z
W70A1-B09 / W70L1-B09
230/208-3
W70A1-B15 / W70L1-B15
W70A1-B18
W70A1-C00, C0Z / W70L1-C00, C0Z
W70A1-C09 / W70L1-C09
460-3
W70A1-C15 / W70L1-C15
1
1
1
1 or 2
1 or 2
1
1
1
2
1
1
1
49
49
59
85
110
43
43
53
60
60
60
90
125
50
50
60
8
8
6
4
2
8
8
6
10
10
10
8
6
10
10
10
23
23
27
30
30
35
10
10
8
10
10
10
59
59
26
52
60
60
30
60
6
6
10
6
10
10
10
10
43
28
60
30
8
10
10
10
Maximum size of the time delay fuse or HACR type circuit breaker for protection of field wiring conductors.
Based on 75°C copper wire. All wiring must conform to the National Electrical Code (NEC) and all local codes.
These “Minimum Circuit Ampacity” values are to be used for sizing the field power conductors. Refer to the National Electric Code (latest revision), article 310 for power conductor sizing.
Caution: When more than one field power conductor circuit is run through one conduit, the conductors must be derated. Pay special attention to note 8 of Table 310 regarding Ampacity
Adjustment Factors when more than 3 conductors are in a raceway.
Electric Heat Table----Refer to Electrical Specifications for Availability by Unit Model
At 240V (1)
Nominal
KW
Kw
5.0
5.0
1-Ph Amps 3-Ph Amps
20.8
9.0
9.0
10.0
10.0
41.7
21.7
15.0
15.0
62.5
18.0
18.0
20.0
20.0
83.3
At 208V (1)
Btuh
Kw
17,065
3.75
1-Ph Amps 3-Ph Amps
18.0
30,717
6.75
34,130
7.50
36.1
54.1
36.1
51,195
11.25
43.3
61,434
13.50
68,260
15.00
At 480V (2)
Btuh
At 460V (2)
Kw
3-Ph Amps
Btuh
Kw
3-Ph Amps
Btuh
9.0
10.8
30,717
8.28
10.4
28,260
15.0
18.0
51,195
13.80
17.3
47,099
12,799
18.7
23,038
25,598
31.2
38,396
37.5
46,076
72.1
51,195
(1) These electric heaters are available in 230/208V units only.
(2) These electric heaters are available in 480V units only.
Heater Packages - Field Installed (W70A Only)
-Designed for adding Electric Heat to 0 KW Units
-Pull Disconnect
-UL Listed
-CUL Listed
-Circuit Breaker Standard on 230/208V Models Standard on 460V Models
-A00 Models
-B00 Models
-C00 Models
Air Conditioner
230/208-1
230/208-3
460-3
Models
Heater Model #
KW
Heater Model #
KW Heater Model # KW
EHWA60-A05
5
EHW70A-B09
9 EHWA05A-C09
9
EHWA05-A10
10
EHWA05-B15
15 EHWA05A-C15 15
W70A 1
EHWA05-A15
15
EHW70A-B18
18
EHWA05-A20
20
Field installed heater package not available for W70L models.
Form No.
S3409-510
Supersedes S3409-1009
Page
2 of 8
Indoor Blower Performance – CFM at 230 Volts
E.S.P.
In H2O
.0
.1
.2
.3
.4
.5
W70A / W70L
HIGH SPEED
LOW SPEED
DRY / WET COIL
DRY / WET COIL
2,200 / 2,000
1,600 / 1,450
2,100 / 1,900
1,525 / 1,375
2,000 / 1,800
– / –
1,875 / 1,700
– / –
1,775 / 1,600
– / –
1,650 / 1,475
– / –
learances Required for Service Access
nd Adequate Condenser Airflow
MODELS
W70A / W70L
M inimum Clearances Required to
Combustible M aterials
LEFT SIDE
RIGHT SIDE
20"
20"
SUPPLY AIR DUCT
FIRST THREE FEET
MODELS 1
W70A / W70L
1/4"
CABINET
0"
Dimensions of Basic Unit for Architectural and Installation Requirements (Nominal)
22.25
Built In Slope
Top 2° Pitch
Electric
Heat
42.00
.44
6.06
2.13
Heater
Access
Panel
43.88
43.00
29.88
Supply
Air Opening
9.88
16.00
Side Wall
Mounting Brackets
(Built In)
30.00
Circuit Breaker
Disconnect Access
Panel (Lockable)
16.00
Electrical
Entrances
16.00
Filter Access
Door
13.50
Return
Air Opening
15.88
Ventilation Air
94.87
Low Voltage
Electrical
Entrances
3.25
10.0
42.70
Condenser Airflow
is Blowthrough on
All Models
37.00
21.00
Electrical
Entrances
44.69
42.43
33.87
21.00
Front View
Right Side View
W70A
W70A
43.88
43.00
29.88
.44
6.06
W70A
22.25
2.13
Back View
Drain
Built In Slope
Top 2° Pitch
Bottom
Installation
Bracket
1.88
MIS-2672
42.00
Electric
Heat
Supply
Air Opening
9.88
Heater
Access
Panel
30.00
Circuit Breaker
Disconnect Access
Panel (Lockable)
16.00
Side Wall
Mounting Brackets
(Built In)
16.00
Filter Access
Door
94.87
16.00
21.00
Electrical
Entrances
Electrical
Entrances
3.25
Return
Air Opening
15.88
13.50
Ventilation Air
Low Voltage
Electrical
Entrances
10.00
37.00
44.69
42.43
33.87
Condenser Airflow
is Blowthrough on
All Models
42.70
21.00
Bottom
Installation
Bracket
Back View
Left Side View
W70L
W70L
Drain
Front View
MIS-2673
W70L
Form No.
S3409-510
Supersedes S3409-1009
Page
3 of 8
Ventilation System Packages
Bard Wall-Mounts are designed to provide optional ventilation packages to meet all of your ventilation and indoor air quality requirements.
All units are equipped with a barometric fresh air damper as the standard ventilation package. All ventilation packages can be built-in at the factory,
or field-installed at a later date.
BAROMETRIC FRESH AIR DAMPER - BFAD
STANDARD
The barometric fresh air damper is a standard feature on all models. It is installed on the inside of the
service door and allows outside ventilation air, up to 25% of the total airflow rating of the unit, to be
introduced through the air inlet openings and to be mixed with the conditioned air. The damper opens
during blower operation and closes when the blower is off. Adjustable blade stops allow different amounts
of outside air to be introduced into the building and can be easily locked closed if required.
Barometric Fresh Air Damper
BLANK OFF PLATE - BOP
OPTIONAL
A blank off plate is installed on the inside of the service door. It covers the air inlet openings, which
restricts any outside air from entering the unit. The blank off plate should be utilized in applications where
outside air is not required to be mixed with the conditioned air.
MOTORIZED FRESH AIR DAMPER - MFAD
OPTIONAL
The motorized fresh air damper is internally mounted behind the service door and allows outside ventilation
air, up to 25% of the total airflow rating of the unit, to be introduced through the air inlet openings and to be
mixed with the conditioned air. The two position damper can be fully opened or closed. The damper blade
is powered open by a 24VAC motor with spring return on power loss. The damper can be controlled by
indoor blower operation or can be field connected to be managed based on building occupancy.
Motorized Fresh Air Damper
NOTE: The above vent systems are intake only without built-in exhaust capability. Building will likely require separate field
installed barometric relief or mechanical exhaust elsewhere within the conditioned space. Balancing dampers in the return air
grille may be required to achieve specified amount of outdoor air intake.
COMMERCIAL ROOM VENTILATOR - CRV
OPTIONAL
The built-in commercial room ventilator is internally mounted behind the service door and allows outside
ventilation air, up to 50% of the total airflow rating of the unit, to be introduced through the air inlet
openings. It includes a built-in exhaust air damper.
Commercial Room Ventilator
The commercial room ventilator (CRV) is a simple and innovative approach to improving the indoor air
quality by providing fresh air intake and exhaust capability through the CRV. The damper can be easily
adjusted to control the amount of fresh air supplied into the building. The CRV can be controlled by indoor
blower operation or field controlled based on room occupancy. Two versions are available: the CRVS is
power open - spring return on power loss; the CRVP is power open and power return. Complies with
ANSI/ASHRAE Standard 62.1 “Ventilation for Acceptable Indoor Air Quality.”
ECONOMIZER - EIFM
OPTIONAL
The built-in economizer system is internally mounted behind the service door and allows outdoor air to be
introduced through the air inlet openings. The amount of outdoor air varies in response to the system
controls and settings defined by the end user. It includes a built-in exhaust air damper. The economizer
is designed to provide “free cooling” when outside air conditions are cool and dry enough to satisfy cooling
requirements without running the compressor. This in turn provides lower operating costs, while extending
the life of the compressor.
Economizer
Energy Recovery Ventilator
Standard Features:
• One Piece Construction - Easy to install with no mechanical linkage adjustment required.
• Exhaust Air Damper - Built in with positive closed position. Provides exhaust air capability to
prevent pressurization of tight buildings.
• Actuator Motor - 24 volt, power open, spring return with built in torque limiting switch.
• Proportioning Type Control - for maximum “free cooling” economy and comfort.
• Moisture Eliminator & Prefilter - permanent, washable aluminum construction.
• Enthalpy Control - adjustable to monitor outdoor temperature and humidity.
• Minimum Position Potentiometer - adjustable to control minimum damper blade position for
ventilation purposes.
• Mixed Air Sensor - to monitor outside and return air to automatically modulate damper position.
WALL-MOUNT ENERGY RECOVERY VENTILATOR - ERVF
OPTIONAL
The wall-mount energy recovery ventilator is a highly innovative approach to meeting indoor air quality
ventilation requirements as established by ANSI/ASHRAE Standard 62.1. The ERVF allows from 200 to
450 CFM (depending upon model) of fresh air and exhaust through the unit while maintaining superior
indoor comfort and humidity levels. In most cases, this can be accomplished without increasing equipment
sizing or operating costs. Heat transfer efficiency is up to 67% during summer and 75% during winter
conditions.
The ERVF consists of a unique “rotary energy recovery cassette” that provides effective sensible and
latent heat transfer capabilities during summer and winter conditions. Various control schemes are
addressed - including limiting ventilation during building occupancy only.
The ERVF is designed to be internally mounted behind the service door in the W70A or W70L model wall
mount units. It can be built-in at the factory or field installed as an option. ERVF-*5C can be independently
adjusted for intake and exhaust rates.
Manufactured under U.S. Patent Nos. 5,485,878; 5,301,744; 5,002,116.
Form No.
S3409-510
Supersedes S3409-1009
Page
4 of 8
Commercial Room Ventilator Performance Data - CRVS-5 and CRVP-5
W70A, W70L HIGH SPEED TOTAL AND VENTILATION AIRFLOW
2200
2100
2000
1900
1800
1700
1600
1500
Airflow (cfm)
1400
Total Air 0 ESP
Total Air .2 ESP
Total Air .4 ESP
Vent Air 0 ESP
Vent Air .2 ESP
Vent Air .4 ESP
1300
1200
1100
1000
900
800
700
600
500
400
300
200
100
0
A
B
C
D
E
F
Vent Position
W70A, W70L LOW SPEED TOTAL AND VENTILATION AIRFLOW
1600
1500
1400
1300
1200
1100
Airflow (cfm)
1000
Total Air 0 ESP
Total Air .2 ESP
Total Air .4 ESP
Vent Air 0 ESP
Vent Air .2 ESP
Vent Air .4 ESP
900
800
700
600
500
400
300
200
100
0
A
B
C
D
E
F
Vent Position
Form No.
S3409-510
Supersedes S3409-1009
Page
5 of 8
Performance and Application Data- ERVF-*5C
SUMMER COOLING PERFORMANCE
(INDOOR DESIGN CONDITIONS 75°DB/62°WB)
Ambient
O.D.
D B/
WB
105
100
F
VENTILATION RATE – 450 CFM
65% EFFICIENCY
VLT
V LS
90
85
80
75
VLT
V LS
VENTILATION RATE – 300 CFM
67% EFFICIENCY
V LL
HRT
HRS
HRL
V LL
HRT
HRS
HRL
VLT
V LS
V LL
HRT
HRS
HRL
75 21465 14580
6884
13952
9477
4475
17887 12150
5737
11805
8018
3786
14310
9720
4590
9587
6512
3075
70 14580 14580
0
9477
9477
0
12150 12150
0
8 0 18
8018
0
9720
9720
0
6512
6512
0
65 14580 14580
0
9477
9477
0
12150 12150
0
8 0 18
8018
0
9720
9720
0
6512
6512
0
80 31590 12150 19440 20533
7897
12635 26325 10125 16200 17374
6682
10692 21060
8100
12960 14110
5427
8683
75 21465 12150
9314
13952
7897
6054
17887 10125
7762
11805
6682
5123
14310
8100
6210
9587
5427
4160
70 12352 12150
202
8029
7897
131
10293 10125
168
6793
6682
111
8235
8100
135
5517
5427
90
65 12150 12150
0
7897
7897
0
10125 10125
0
6682
6682
0
8100
8100
0
5427
5427
0
60 12150 12150
0
7897
7897
0
10125 10125
0
6682
6682
0
8100
8100
0
5427
5427
0
9720
21870 20533
6318
14215 26325
5345
12028 21060
6480
14580 14110
4341
9768
80 31590
95
VENTILATION RATE – 375 CFM
66% EFFICIENCY
8100
18225 17374
75 21465
9720
11744 13952
6318
7634
17887
8100
9787
11805
5345
6459
14310
6480
7830
9587
4341
5246
70 12352
9720
2632
8029
6318
1711
10293
8100
2193
6793
5345
1447
8235
6480
1755
5517
4341
1175
65 9720
9720
0
6318
6318
0
8100
8100
0
5345
5345
0
6480
6480
0
4341
4341
0
60 9720
9720
0
6318
6318
0
8100
8100
0
5345
5345
0
6480
6480
0
4341
4341
0
80 31590
7290
24300 20533
4738
15794 26325
6075
20250 17374
4009
13365 21060
4860
16200 14110
3256
10854
75 21465
7290
14175 13952
4738
9213
17887
6075
11812 11805
4009
7796
14310
4860
9450
9587
3256
6331
70 12352
7290
5062
8029
4738
3290
10293
6075
4218
6793
4009
2784
8235
4860
3375
5517
3256
2261
65 7290
7290
0
4738
4738
0
6075
6075
0
4009
4009
0
4860
4860
0
3256
3256
0
60 7290
7290
0
4738
4738
0
6075
6075
0
4009
4009
0
4860
4860
0
3256
3256
0
80 31590
4860
26730 20533
3159
17374 26325
4050
22275 17374
3240
17820 14110
2170
11939
2672
14701 21060
75 21465
4860
16605 13952
3159
10793 17887
4050
13837 11805
2672
9132
14310
3240
11070
9587
2170
7416
70 12352
4860
7492
8029
3159
4870
10293
4050
6243
6793
2672
4120
8235
3240
4995
5517
2170
3346
65 4860
4860
0
3159
3159
0
4050
4050
0
2672
2672
0
3240
3240
0
2170
2170
0
60 4860
4860
0
3159
3159
0
4050
4050
0
2672
2672
0
3240
3240
0
2170
2170
0
75 21465
2430
19035 13952
1579
12372 17887
2025
15862 11805
1336
10469 14310
1620
12690
9587
1085
8502
70 12352
2430
9922
8029
1579
6449
10293
2025
8268
6793
1336
5457
8235
1620
6615
5517
1085
4432
65 4252
2430
1822
2764
1579
1184
3543
2025
1518
2338
1336
1002
2835
1620
1215
1899
1085
814
60 2430
2430
0
1579
1579
0
2025
2025
0
1336
1336
0
1620
1620
0
1085
1085
0
70 12352
0
12352
8029
0
8029
10293
0
10293
6793
0
6793
8235
0
8235
5517
0
5517
65 4252
0
4252
2764
0
2764
3543
0
3543
2338
0
2338
2835
0
2835
1899
0
1899
60
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
ERVF-*5C WINTER HEATING PERFORMANCE
(INDOOR DESIGN CONDITIONS 70°F DB)
VENTILATION RATE
Ambient
450 C F M
375 C F M
300 C F M
O.D.
80% EFF.
81% EFF.
82% EFF.
DB/°F
WVL
WHR
WVL
WHR
WVL
WHR
65
2430
1944
2025
1640
1620
1328
60
4860
3888
4050
3280
3240
2656
55
7290
5832
6075
4920
4860
3985
50
9720
7776
8100
6561
6480
5313
45
12150
9720
10125
8201
8100
6642
40
14580
11664
12150
9841
9720
7970
35
17010
13608
14175
11481
11340
9298
30
19440
15552
16200
13122
12960
10627
25
21870
17496
18225
14762
14580
11955
20
24300
19440
20250
16402
16200
13284
15
26730
21384
22275
18042
17820
14612
NOTE: Sensible performance only is show n for w inter application.
Form No.
S3409-510
Supersedes S3409-1009
Page
6 of 8
LEGEND:
VLT = Ventilation Load - Total
VLS = Ventilation Load - Sensible
VLL = Ventilation Load - Latent
HRT = Heat Recovery - Total
HRS = Heat Recovery - Sensible
HRL = Heat Recovery - Latent
WVL= Winter Ventilation Load
WHR = Winter Heat Recovery
Cooling Application Data — Outdoor Temperature °F
Model
W70A1
W70L1
D.B./W.B.
1
2
Cooling
Capacity
75°F
80°F
85°F
90°F
95°F
100°F
105°F
110°F
115°F
120°F
125°F
75/
62
Total Cooling
Sensible Cooling
74,200
53,000
70,000
51,400
66,200
49,900
62,600
48,300
59,200
46,700
56,100
45,100
53,100
43,600
50,500
42,000
47,900
40,500
45,500
38,900
43,300
37,300
80/
67
Total Cooling
Sensible Cooling
79,200
51,400
76,300
50,400
73,500
49,400
70,800
48,300
68,000
47,100
65,400
45,900
62,700
44,700
60,200
43,400
57,600
42,100
55,100
40,700
52,700
39,300
85/
72
Total Cooling
Sensible Cooling
94,300
52,600
89,200
51,200
84,400
49,600
79,900
48,000
75,500
46,200
71,500
44,400
67,600
42,600
64,000
40,700
60,500
38,800
57,300
36,800
54,200
34,800
Below 65°F, unit requires a factory or field installed low ambient control.
Return air temp. °F.
Capacity Multiplier Factors
% of Rated Airflow
Total BTUH
Sensible BTUH
-10
0.975
0.950
Rated
1.0
1.0
+10
1.02
1.05
Form No.
S3409-510
Supersedes S3409-1009
Page
7 of 8
Air Conditioning Wall-Mount Model Nomenclature
W
70
A
1
A
10
X
X
X
X
X
X
SERIES |
REVISION
NOMINAL
CAPACITY |
70 - 6 Ton
VOLTS & PHASE |
A - 230/208/60/1
B - 230/208/60/3
C - 460/60/3
| CONTROL MODULES
(See Chart Below)
KW
VENTILATION OPTIONS
(See Table Below)
TYPE
A = Compressor & Controls - Right Side
L = Compressor & Controls - Left Side
FILTER OPTIONS
X - 1-inch Throwaway (Standard)
W - 1-inch Washable
P - 2-inch Pleated
| COIL OPTIONS
X - Standard
1 - Phenolic Coated Evaporator
2 - Phenolic Coated Condenser
3 - Phenolic Coated Evaporator
and Condenser
COLOR OPTIONS
X - Beige (Standard)
1 - White
4 - Buckeye Gray
5 - Desert Brown
8 - Dark Bronze
A - Aluminum
S - Stainless Steel
| OUTLET OPTIONS
X - Front (Standard)
Note: For 0KW and circuit breakers (230/208 Volt) or toggle disconnects (460 Volt) applications, insert 0Z in the KW field of the model number.
Ventilation
Models
W70A, W70L
Factory Installed
Field Installed
Code No.
Part No.
X
BFAD-5
B
BOP-5
M
MFAD-5
V
CRVS-5
E
EIFM-5C
D
N/A
R
ERVF-A5 3
R
ERVF-C5 3
N/A
WMDK5-
Description
Barometric Fresh Air Damper - Standard
Blank-Off Plate
Motorized Fresh Air Damper
Commercial Ventilator - Spring Return w/Exhaust
Economizer - Fully Modulating 1
Economizer - Fully Modulating 12
Energy Recovery Ventilator - 230 Volt Energy Recovery Ventilator - 460 Volt Door Kit for ERVF (Required)
1
2
3
Low ambient control is required with economizer for low temperature compressor operation.
For use only with “V” Control Module and TCS23 Controller.
Intake and exhaust can be independently adjusted.
WMDK Door Kit must be ordered in addition to ERVF Assembly and color matched to unit ("X" = Beige; "4" = Buckeye Gray; "8" = Dark Bronze)
Air Conditioning Control M odules
HPC 1
LP C 2
CCM 3
STD
STD
STD
STD
STD
STD
STD
STD
STD
STD
STD
STD
STD
STD
STD
STD
STD
STD
STD
STD
STD
STD
STD
STD
STD
STD
STD
STD
STD
STD
STD
STD
STD
LA C 4
A LR 5
W70A, W70L
SK 6
SK 7
ODT 8
DDC 9
Factory Installed Code
Field Installed Part
X
N/A
E
CMA-28
J
Factory Only
K
CMC-15 and CMA-28
M
Factory Only
N, W18L Only
N/A
Field Installed Only
CMC-15
Field Installed Only
CMA-14
V
Factory Only
Field Installed Only
CMA-24
Field Installed Only
SK117
STD = Standard equipment for these specified models.
1 HPC. High pressure control is auto reset. Always used with compressor control module (CCM) which is included. See note 3.
2 LPC. Low pressure control is auto reset. Always used with compressor control module (CCM) which is included. See note 3.
3 CCM. Compressor control module has adjustable 30-second to 5-minute delay-on-break timer. On initial power-up, or any time the power is interrupted, the delay-on-make will be 2minutes plus 10% of the delay-on-break setting. There is no delay-on-make during routine operation of the unit. The module also provides the lockout feature (with 1 retry) for
high and/or low-pressure controls, and a 2-minute timed bypass for low-pressure control.
4 LAC. Low ambient control permits cooling operation down to 0°F
5 ALR. The alarm relay has a set of normally open and normally closed dry contacts to provide the ability to signal a condition of shutdown on either high or low pressure controls.
6 SK. PTCR start kit can be used with all -A single phase models. Increases starting torque 2-3x. Not used for -B or -C three phase models. Do not use if SK117 is used.
7 SK. Start capacitor and potential relay start kit can be used with all -A single phase models. Increases starting torque 9x. Not used for -B or -C three phase models. Do not use if
CMC-15 is used.
8 ODT. Outdoor thermostat is adjustable from 0 to 50°F. It is suitable for use as a compressor cut-off thermostat.
9 DDC. Incorporates 4 additional sensors: discharge air temperature, indoor blower airflow, compressor current, and dirty filter. These sensing devices function to input analog data
such as temperature, as well as digital data such as airflow, compressor status or filter status.
“V” control module should be ordered in conjunction with direct digital controller (DDC) model TCS23. Refer to DDC specification sheet S3280 for more information.
Bard Manufacturing Company, Inc.
Bryan, Ohio 43506
www.bardhvac.com
Form No.
S3409-510
Supersedes S3409-1009
Page
8 of 8
Due to our continuous product improvement policy,
all specifications subject to change without notice.
Before purchasing this appliance, read important
energy cost and efficiency information available from
your retailer.
Form No.
S3409
May, 2010
Supersedes S3409-1009