EFD.qxd 08.1.18 4:18 PM ページ 1
FK1260 0108 C
JF-2MED, JF-2HD
HANDS-FREE COLOR VIDEO INTERCOM
INTERPHONE VIDEO COULEUR MAINS LIBRES
HANDENVRIJE KLEURENVIDEOFONIE
JF-2MED
JF-2HD
Master monitor station
Moniteur maître
Monitor-hoofdpost
Sub monitor station
Moniteur secondaire
Monitor-bijpost
-1-
INSTALLATION & OPERATION MANUAL
MANUEL D’INSTALLATION ET D’UTILISATION
INSTALLATIE- EN BEDIENINGSHANDLEIDING
EFD.qxd 08.1.18 4:18 PM ページ 2
PRECAUTIONS
Français
English
General Prohibitions
Prohibition to Dismantle the Unit
Prohibition on Subjecting the Unit to Water
WARNING
GENERAL PRECAUTIONS
(Negligence could result in death or serious injury.)
1. Keep the unit more than 1 m away from radio or TV set.
2. This unit is for indoor use only. Do not use outdoors.
3. In areas where broadcasting station antennas are close by, the intercom system may
be affected by radio frequency interference.
4. As to other manufacturer's devices (such as sensor, detectors, door releases) used
with this system, comply with the Specifications and Warranty conditions that the
manufacturers or venders present.
5. Keep the intercom wires more than 30 cm (12") away from AC 100~240 V lines.
Noise and malfunction could result.
6. If the unit is down or does not operate properly, unplug the power supply or turn off
the JF-2MED and JF-2HD Power switches.
7. The unit is for wall-mount use only. For desktop applications, use desk stand.
8. When wall-mounted, the unit may become dusty. Clean with a soft cloth.
9. The unit case may become a warm with use, but this is not a unit malfunction.
10. If a cellular phone is used close by, the unit may malfunction.
11. If must be noted in advance that the LCD panel, though manufactured with very high
precision techniques, inevitably will have a very small portion of the picture
elements steadily lit or not lit at all, which is not considered a unit malfunction.
12. Refrain from using the color monitor station in sunlit areas.
13. At night, due to reduced lighting on the object, the monitor sees more noise and the
face becomes more difficult to see, but this is not malfunction.
14. Talk within 50 cm (20") or less from the unit. If you stand too far away, it may be
difficult for the other person to hear the communication.
15. If there are loud noises around the unit (such as music playing or children crying),
the sound may break up and be difficult to hear.
16. During communication, if you speak before the other person has finished talking,
your voice may not be heard. Communication will proceed smoothly if you wait
until the other person has finished before speaking.
17. At a gate or porch illuminated by fluorescent lamp, the picture may vary, but this is
not a malfunction.
18. When outside temperature lowers sharply after rainfall, etc., the inside of the camera
may fog up slightly, causing a blurry picture, but this is not a malfunction. Normal
operation will be restored when moisture evaporates.
19. Due to the environmental sound around the unit, it may hinder smooth
communication, but this is not a malfunction.
1. High voltage is present internally. Do not open the case. Electric shock could result.
2. Do not dismantle or alter the unit. Fire or electric shock could result.
3. Do not connect any non-specified power source to the +, - terminals, and do not
install two power supplies in parallel to a single input. Fire or damage to the unit
could result.
4. Keep the unit away from water or any other liquid. Fire or electric shock could result.
5. Do not put any metal or flammable material into the unit through the openings. Fire
or electric shock could result.
6. Do not use power supply with a voltage other than specified. Fire or electric shock
could result.
7. Do not connect any terminal on the unit to AC power lines. Fire or electric shock
could result.
CAUTION
Nederlands
(Negligence could result in injury to people or damage to property.)
1. Do not install or make any wire terminations while power supply is plugged in. It
can cause electrical shock or damage to the unit.
2. Before turning on power, make sure wires are not crossed or shorted. If not, fire or
electric shock could result.
3. When mounting the unit on wall, install the unit in a convenient location, but not
where it could be jarred or bumped. Injury could result.
4. For power supply, use Aiphone power supply model specified with system. If nonspecified product is used, fire or malfunction could result.
5. Do not install the unit in any of the following locations. Fire, electric shock, or unit
trouble could result.
∗ Places under direct sunlight, or near heating equipment that varies in temperature.
∗ Places subject to dust, oil, chemicals, etc.
∗ Places subject to moisture and humidity extremes, such as bathroom, cellar,
greenhouse, etc.
∗ Places where the temperature is quite low, such as inside a refrigerated area or in
front of air-conditioner.
∗ Places subject to steam or smoke (near heating or cooking surfaces).
∗ Where noise generating devices such as dimmer switches or inverter electrical
appliances are close by.
6. Do not put anything on or cover the unit with cloth, etc. Fire or unit trouble could
result.
7. Do not press on the LCD or subject it to a high impact. The LCD glass could be
punctured and result in an injury.
8. If LCD is punctured, do not allow contact with the liquid crystal inside.
Inflammation could result.
∗ If necessary, gargle your mouth and clean your eyes or skin with clear water for at
least 15 minutes, and consult your doctor.
1
General Precautions
PACKAGE CONTENTS
JF-2MED or JF-2HD
Mounting screws x 2
Wood mounting screws x 2
Option connector
Release connector (JF-2MED only)
Installation & Operation manual
-2-
EFD.qxd 08.1.18 4:18 PM ページ 3
2
INSTALLATION
2-1 Mounting locations
2 The master monitor station and sub
1 Install the master monitor station and
3 Allow 15 cm (6") or more of vertical open space
monitor station have switches on both
sides.
Allow at least 5 cm (2") of open space on
either side.
from the center of the mounting bracket in order
to mount the master monitor station and sub
monitor station.
JF-2MED / JF-2HD
2
+ 5 cm
(2")
English
sub monitor station in places where
the screens are not exposed to direct
sunlight.
3
+ 15 cm
(6")
+ 5 cm
(2")
Français
2-2 Wiring method, Wiring distance
A
Incorrect method
B
JF-2HD
JF-2MED
JF-DA
JF-2HD
4
2
D1
2
JF-DA
JF-DV
JF-DVF
JF-2HD
JF-2MED
2
4
JF-2SD
4
4
JF-2HD
2
4
C
D2
D
JF-2SD
JF-2MED
JF-DA
JF-2SD
2
JF-DA
JF-DV
JF-DVF
JF-D
PS-1820
PS-1810DIN
PS
4
SP IER-2
JF-2SD
JF-2HD
2
A
B
C
D
JF-2SD
JF-2HD
Ø 0,65 mm
50 m
50 m
5m
75 m
22AWG
165'
165'
16'
245'
Ø 1,0 mm
100 m
100 m
10 m
150 m
8
18AWG
330'
330'
33'
490'
JF-2SD
2-3 Cable
1 Parallel or jacketed 2-conductor, mid-capacitance nonshielded cable is recommended. PVC jacket with PE
(polyethylene) insulated conductors is recommended.
3 When using a cable with unused conductors, terminate both ends of the
unused pair(s) with a 120 Ω resistor.
JF-DA
JF-DV A1
JF-DVF A2
(x2)
JF-DA
JF-DV A1
JF-DVF A2
2 Never use individual conductors, twisted pair cable or
JF-D
coaxial cable.
JF-2MED
JF-2HD
A1
A2
A1
A2
B1
B2
S
S
B1
B2
B1
B2
+
-
+
-
120
-3-
120
Nederlands
Wire the units from station-to-station (daisy-chained).
EFD.qxd 08.1.18 4:18 PM ページ 4
3
WIRING
Insert wires securely into each terminal as shown.
English
DOOR 1 Video door station
JF-2MED
AIPHO
NE
JF-DA
Master monitor station
JF-DA
AIPHONE
JF-DVF
AIPHON
E
JF-DV
JF-DV
JF-DVF
#2
#1
Français
A1 A2
2
Nederlands
NP
DOOR 2
AIPHO
NE
JF-DA
JF-DA
AIPHONE
JF-DVF
AIPHON
E
JF-DV
JF-DV
JF-DVF
P
JF-D
(Audio only)
Setting is required. (Refer to section 7-7)
+
DC 18 V
A1 A2
PS-1820
230V AC
2
N
IN 230V~ 50/60Hz
NL
1A - +
18V DC 1 A
2
NP
Door release
OP
2
[1]
NP
PT
EL-9S
RY-3DL
EL-9S
EL-9S
PT
L1
C1
L1
L2
C2
L2
JF-2MED
Option connector
b1
b2
b3
L
D1
E
D2
OG(b1)
YE(b2)
GR(E)
Release connector
BR(L)
RD(L)
DC 18V
PT
AC Transformer
+
–
+
–
PS18
-4-
[1]
(BR)
(RD)
(OG)
(YE)
(GR)
(BL)
(PR)
(GY)
(WH)
[3]
V+
Vb1
b2
E
PK
FS
KS
E
[2]
[4]
[7]
Door release
or
RY-3DL
RY-3DL
[6]
[5]
Control external devices connected with release connector and
option connector.
[1] Door release output
Setting is required. (Refer to section 7-8)
(AC/DC 24 V, 0.5 A N/O dry closure contact)
Connect the brown and red wires from the release connector to the
door release (or to the RY-3DL as shown in the wiring diagram).
[2] Options output
(AC/DC 24 V, 1.6 A N/O dry closure contact)
1 E
Door release EL-9S (AC 12 V, 0.35 A) or
equivalent, requires a separate AC transformer.
Run separate cables for audio/video and door
release.
Door release contact: AC/DC 24 V, 0.5 A
(N/O dry closure contact L, L).
(BR) L
(RD) L
(OG) SW
(YE) SW
To prevent shorts, be sure to cut unused lead wires
at the bottom and insulate the ends.
18V DC
100V - 240V - 2 A
50/60 Hz
+
Optional call extension speaker IER-2
Optional selective door release
adaptor RY-3DL
Use RY-3DL when connecting
door release to 2 locations.
Option connector
#2
L
NP
IER-2
#1
Power supply +, - (DC 18 V)
PS-1810DIN
OP
Release connector
2
[3] Video signal output
(NTSC, 1 Vp-p/75 Ω) Wiring distance: 3 m
NOTES: When video signal is output to the external
equipment, it may be possible to hear the buzz noise
from master station. Consult AIPHONE distributor.
[4] Door release-linked entrance output
[5] Press-to-talk setting input
If the blue and white wires are shorted, press-to-talk will not
be operable.
[6] Foot switch input
Connect a commercially-available foot switch to the purple
and white wires (N/O dry closure contact).
[7] External sensor input Setting is required. (Refer to section 7-9)
N/O dry closure contact
Input method
External sensor input
(start signal only detection method)
Detection confirmation time 100 mS or more
During dry closure: Less than 700 Ω
Contact resistance
Terminal short current
Less than 10 mA
Less than DC 20 V
Voltage between terminals
(when open between terminals)
EFD.qxd 08.1.18 4:18 PM ページ 5
JF-2HD Sub monitor station
Option connector
JF-2HD Sub monitor station
(BR)
(RD)
(OG) SW
(YE) SW
(GR)
(BL) PK
(PR) FS
(GY)
(WH) E
#3
[5]
[6]
English
#3
[2]
#3
To prevent shorts, be sure to cut unused lead wires
at the bottom and insulate the ends.
Français
4
4
- +
Brown
Red
Orange
Yellow
Green
Blue
Purple
Gray
White
ON
• Terminal setting (2nd unit)
Setting changes are only required when a 3rd unit is connected.
Put the switch in the ON position, and terminate the furthest sub station.
If the terminal setting is incorrect, the monitor station and sub station will
make a warning sound when they are operated.
Further, the unit may not operate correctly or the video image may distort.
JF-2SD
ON side when no 3rd unit is connected
(leave in the factory settings)
OFF side when a 3rd unit is connected
OFF
After changing the setting, be sure to turn the power of the
monitor station on again.
JF-2SD
Sub station
Sub station
ON
ON
OFF
OFF
1
SW1
ON
2
3
4
5
6
1
SW1
SW5 1st unit 2nd unit
Yes
Call-in from door station 1
ON
JF-2MED JF-2SD
ON
2
3
4
5
6
SW5 1st unit 2nd unit 3rd unit
Yes
JF-2MED JF-2SD JF-2SD
OFF
ON
Call-in from door station 1
No
No
SW2
ON
1st unit 2nd unit 3rd unit
JF-2MED JF-2HD JF-2HD
OFF
ON
SW2
ON
Yes
Call-in from door station 2
Yes
Not used.
Call-in from door station 2
Not used.
No
No
Optional long distance adaptor JBW-BA
Use JBW-BA when the wiring distance between the
video door station and JF-2MED is within the distance
range shown in the table.
1. Use PE (polyethylene) insulated cable.
Do not use PVC.
AIPHON
JF-DA
E
JF-DA
JF-DV
JF-DVF
A1
A2
A
B (max.)
C (max.)
Ø 1.0 mm
100~200 m
50 m
50 m
18 AWG
330'~650'
165'
165'
Use THE
power SAME VOLTAGE
supply
station's.
as Master
A1 A2
to Door
DC24V
+
station
or 18V
-
JBW-BA
JF-2MED
to Master
(Observe station
polarity)
B1 B2
A
B
2
NP
1
Ø 1.2 mm
100~250 m
50 m
50 m
-5-
A1
A2
B1
B2
+
-
16 AWG
330'~820'
165'
165'
2
1
P
2
A1
A2
+
-
1
P
PS18
C
Nederlands
BR:
RD:
OG:
YE:
GR:
BL:
PR:
GY:
WH:
ON
1st unit 2nd unit
JF-2MED JF-2HD
ON
OFF
NP: Non-polarized
P: Polarized
- +
EFD.qxd 08.1.18 4:18 PM ページ 6
4
MOUNTING
Mounting screws x 2
Back wiring
1-gang box
English
JF-2MED
JF-2HD
83,5 mm
(3-5/16")
Peel off the protective film
from the display surfaces
of the JF-2MED and JF2HD.
Français
Mounting bracket
1. Press the RELEASE button (to insert or
remove the wire).
2. Insert the cable into the terminal.
1
2
Nederlands
9mm
(3/8")
Surface wiring
∗ Cut open the cable inlet hole to
run wires to the back of the unit.
* When a 1-gang box is not mounted,
the cable can be surface-run to the top
or bottom of the unit. Cut the cable
inlet to allow passage of the wiring
into the unit.
PS-1820
PS-1810DIN
Mounting bracket
Din rail
1-gang box
Wood mounting screws x 2
83,5 mm
(3-5/16")
83,5 mm
(3-5/16")
Mounting bracket
5
NAMES
JF-2MED
JF-2HD
[1]
[1]
[2]
[3]
[7]
[8]
[9]
[1]
[2]
[3]
[4]
[5]
[6]
[2]
[12]
[4]
[5]
[6]
[13]
[3]
[7]
[8]
[9]
[14]
[15]
[12]
[4]
[5]
[6]
[14]
[15]
[10]
[10]
[11]
[11]
Microphone
Color LCD video monitor (3-1/2" color)
CALL button, door call-in LED (red)
PLAY button, play LED (red)
REC button, record LED (red)
MENU/MEMO button, memo LED (red) (JF-2MED)
MENU button (JF-2HD)
[7] POWER switch
[8] MONITOR button
[9] Speaker
[10] Transmit LED (red)
[13]
[11] TALK button
[12] Screen brightness control
[13] Receive volume control (high to off)
[14] Chime tone, alert sound volume (high to off)
NOTES: 1. Even when the volume is turned "Off", sometimes it may be possible to faintly
hear the entrance chime tone depending on the surrounding area.
2. The volume of chime tone and the notification sound will not change while they
are operating even if the volume control is adjusted. The adjusted volume will
apply from the next call-in or notification. (JF-2MED only)
[15] Call-in setting switch
"1": Call-in from door station 1 only.
"2": Call-in from door station 2 only.
"1&2": Call-in from both door station 1 and door station 2.
-6-
EFD.qxd 08.1.18 4:18 PM ページ 7
6
OPERATING METHOD
Main symbols and function descriptions
To operate this unit, check the symbol and then press the appropriate
operation button. This is not a touch-panel operation.
Symbol
Operation guidance display
The guidance differs according to the
screen.
To play Message 1 for entrance.
Symbol
The symbols differ according to the
screen.
To play Message 2 for entrance.
Operation buttons
Press to select a symbol that is displayed
on the screen.
∗ The name of the operation button may
differ from the name of the symbol.
To display the previous (more recent date) image.
To manually record.
To record Voice memo or Message for entrance.
To return to the screen of the previous operation.
To play Recorded image or Voice memo.
To display the next (older date) image.
To erase a Voice memo.
To erase a Recorded image.
To move the cursor up.
To move the cursor down.
To fast forward the play screen.
To pause the play screen.
To reverse the play screen frame by frame.
SETTING UP
7-1 Setting screens and display methods
JF-2MED
3 Press PLAY button or REC button to select the item you want to set
setting screen is displayed (approx. 3 seconds).
or check, and set with CALL button.
SET THE DATE/TIME
2006 01 JAN 00:00
To set the year, date, and time.
SET THE BACKGROUND COLOR
To set the screen background color.
SELECT CALL TONE (DOOR1)
To set the chime tone for door station 1.
SELECT CALL TONE (DOOR2)
To set the chime tone for door station 2.
RECORD MESSAGE
To record a greeting message.
SET DOOR2
To set the connection for door station 2.
SET DOOR RELEASE
To set whether the door release is on or off.
SET EXTERNAL SENSOR INPUT
To set the external sensor input.
RESTORE DEFAULT SETTING
To initialize the settings.
2006 01 JAN 00:00
ENG FRA GER SPA DUT
SET THE DATE/TIME
SET UP
2 Press PLAY button or REC button to select "SET UP", and press
CALL button.
ENG FRA GER SPA DUT
SET UP
Displays a list of all setting items.
SELECT THE LANGUAGE
ENG FRA GER SPA DUT
To select the language used in the unit display.
SET UP
4 Press TALK button to return to the standby mode.
1. When using the unit for the first time, set the time first. If the unit is
used without setting the time, the play LED (red) and record LED (red)
light at the same time as a notification.
2. When power is not supplied to the unit for a long time, the time returns to
its initial setting of "2006 01 JAN 00 : 00", and the play LED (red) and
record LED (red) light at the same time as a notification. Reset the time.
7-2 SELECT THE LANGUAGE
3. If time is not correctly set, there is a case recording might not
function properly.
4. The installer must perform "SET DOOR2", "SET DOOR
RELEASE" and "SET EXTERNAL SENSOR INPUT".
Please do not change these settings yourself.
JF-2MED
1 After performing step 1 in section 7-1, select "SELECT THE
2 In the language selection screen, press the PLAY button or REC
LANGUAGE" and press CALL button.
button to select the language.
ENG FRA GER SPA DUT
ENG
SPA
FRA
DUT
GER
SELECT THE LANGUAGE
LANGUAGE
3 Press the CALL button to set.
SELECT THE LANGUAGE
-7-
Nederlands
To advance the play screen frame by frame.
1 In the standby mode, press the MENU/MEMO button until the
Français
To save or erase an image.
To operate a symbol, press the operation button
that is below the symbol.
Example: To activate the door release, press
CALL button that is below the
symbol.
7
English
PRESS THE TALK BUTTON TO END
Function description
To activate Door release.
EFD.qxd 08.1.18 4:18 PM ページ 8
7-3 SET THE DATE/TIME
JF-2MED
1 After performing steps 1 and 2 in section 7-1, select "SET
3 Press CALL button to set the "Year" and move the cursor to "Month".
THE DATE/TIME" and press CALL button.
English
2006 01 JAN 00:00
2006 01 JAN 00 : 00
SELECT
2 In the time setting screen, press PLAY button or REC button to
4 Perform the same steps to set the "Month", "Day", "Hour" and "Minute".
After setting "Minute", press CALL button to complete the settings.
5 Press TALK button to return to the standby mode.
set the "Year".
1. If there are no operations for approx. 1 minute during the setup mode, the
setting will end automatically. If the settings end while incomplete, start
again from the beginning.
2. A maximum error of 1 minute can occur in the displayed time over a
month.
Français
2006 01 JAN 00 : 00
Nederlands
SET
SET THE DATE/TIME
SELECT
SET
NOTES: Button operations for setting date/time
• PLAY button (press once): The date/time increases by one.
• PLAY button (press and hold for 1 second or more): The date/time increases in succession.
• REC button (press once): The date/time decreases by one.
• REC button (press and hold for 1 second or more): The date/time decreases in succession.
• MENU/MEMO button: Return to the setting screen without saving the setting.
• CALL button: Confirm the setting.
7-4 SET THE BACKGROUND COLOR
The background color for the screen can be selected from 4
alternatives: "Black", "Orange", "Green" and "Blue".
When a sub monitor station is connected, the screen background
color for the sub monitor station also changes.
JF-2MED
2 In the "SET THE BACKGROUND COLOR" screen, press PLAY button or
REC button to select the desired color. The background color changes to the
selected color, enabling you to check the color.
1 After performing steps 1 and 2 in section 7-1, select "SET THE
BACKGROUND COLOR" and press CALL button.
SELECT
2006 01 JAN 00:00
SET
3 Press CALL button to complete the settings and return to the setting screen.
SELECT
SET THE BACKGROUND COLOR
7-5 SELECT CALL TONE
SET
JF-2MED
The chime tone for the video door station can be selected from
4 sound types.
1 After performing steps 1 and 2 in section 7-1, select "SELECT
2 In the "SELECT CALL TONE" screen, press PLAY button or REC button to
select the desired chime tone. The selected chime tone sounds, enabling you to
check the sound.
CALL TONE (DOOR1)" or "SELECT CALL TONE
(DOOR2)" and press CALL button.
2006 01 JAN 00:00
SELECT
SET
3 Press CALL button to complete the settings and return to the setting screen.
SELECT CALL TONE (DOOR1)
7-6 RECORD MESSAGE
SELECT
SET
JF-2MED
A maximum of 2 messages can be recorded (approx. 10 seconds
per message).
2 In the message recording screen, press CALL button or PLAY button to select
the record location. If a message has already been recorded, the selected
message is played, enabling you to check the contents of the recording.
1 After performing steps 1 and 2 in section 7-1, select "RECORD
MESSAGE" and press CALL button.
Message 1 for entrance
Message 2 for entrance
SELECT
RECORD MESSAGE
RECORD
3 Press the REC button to record a message. Recording is possible for approx. 10 seconds.
SELECT
RECORD
4 After approx. 10 seconds have passed, press CALL button to complete the recording.
RECORDING (8 SEC. REMAINING)
-8-
EFD.qxd 08.1.18 4:18 PM ページ 9
7-7 SET DOOR2
JF-2MED
2 In the "SET DOOR2" screen, press PLAY button or REC button to
When connecting door station 2, set "Video", "Audio" or "None
(door station 2 not connected)".
These operations must be performed by an installer. Please
do not change these settings yourself.
select the type of door station that is connected.
1 After performing steps 1 and 2 in section 7-1, select "SET
DOOR2" and press CALL button.
SELECT
SET
English
Video door station
Audio door station
Door station 2 not connected
3 Press CALL button to complete the settings and return to the
setting screen.
SELECT
SET DOOR2
JF-2MED
2 In the "SET DOOR RELEASE" screen, press the PLAY button or
When not connecting the door release, set to "Not use".
These operations must be performed by an installer. Please
do not change these settings yourself.
REC button to select the setting.
When "Not use" is selected, door release symbol is not displayed on
the menu screen. (Refer to section 8-2)
1 After performing steps 1 and 2 in section 7-1, select "SET DOOR
Use
Not use
SELECT
SET DOOR RELEASE
SET
3 Press CALL button to complete the settings and return to the setting screen.
SELECT
SET
JF-2MED
JF-2MED
When optional units operate (for example, when a sensor is activated or a
call button is pressed), the master monitor station and sub station will
receive a notification sound. Further, when
is set, door station 1
also receives a notification sound.
These operations must be performed by an installer. Please do not
change these settings yourself.
2 In the "SET EXTERNAL SENSOR INPUT" screen, press PLAY button
or REC button to select the notification sound contents.
SELECT
SET
The notification sound stops after 30 seconds.
The notification sound operates continuously.
The notification sound operates continuously,
and is also sounded at door station 1.
1 After performing steps 1 and 2 in section 7-1, select "SET
EXTERNAL SENSOR INPUT" and press CALL button.
3 Press CALL button to complete the settings and return to the setting screen.
SELECT
SET
SET EXTERNAL SENSOR INPUT
7-10 RESTORE DEFAULT SETTING
JF-2MED
1 After performing steps 1 and 2 in section 7-1, select "RESTORE
All settings can be restored to their condition at the time of purchase.
1. Once the settings are initialized, they cannot be restored to their
previous settings.
2. Recorded images, Voice memos, and Messages for the entrance
are also all erased.
DEFAULT SETTING" and press CALL button.
Settings reset with "RESTORE DEFAULT SETTING"
Setting name
2 In the "RESTORE DEFAULT SETTING" screen, press CALL button
Time
2006 01 JAN 00 : 00
Screen background color
Black Orange Green Blue
Door station 1 chime tone
1 (Tone 1)
Door station 2 chime tone
1 (Tone 1)
Door station 2
(Video)
Door release on or off
(Use)
External sensor input
(30 seconds)
∗
RESTORE DEFAULT SETTING
Available settings
to initialize. Press PLAY button to return to the setting screen.
2 (Tone 2)
3 (Tone 3)
4 (Tone 4)
2 (Tone 2)
3 (Tone 3)
4 (Tone 4)
(Audio)
(None)
DO YOU WANT TO INITIALIZE?
(Not use)
(Continuous)
3 "INITIALIZING" is displayed. Initializing takes max. 60 seconds.
(Outdoor output)
are the initial values.
-9-
Nederlands
RELEASE" and press CALL button.
7-9 SET EXTERNAL SENSOR INPUT
Français
7-8 SET DOOR RELEASE
SET
EFD.qxd 08.1.18 4:18 PM ページ 10
8
OPERATIONS
8-1 Answering a door call (HANDS-FREE mode, PTT mode)
1 Press CALL button.
English
Instant voice call function
2 Even without answering, door area can be seen and heard with video
and audio (for approx. 45 seconds). Inside sound is not heard outside.
Français
2 Chime tone sounds, caller is seen on video monitor, and
outside sound is heard.
• Audio and video turns off after approx. 45 seconds in not
answered.
NOTES: Not available on JF-D audio door station.
PTT mode
3 Press and hold TALK button for 1 second or more to change to press-to-
Nederlands
talk mode. A beep sounds, and after approx. 1 second another beep
sounds, PTT mode is entered. If TALK button is pressed briefly (less
than 0.5 seconds), communication ends.
3 Press TALK button momentarily, and after the beep, communicate
hands-free. Transmit LED (red) lights when you talk, and goes off as
you listen to caller (or hear outside sounds).
4 To continue speaking using the press-to-talk mode, press TALK button
for 1 second or more each time to talk, and release to listen to the caller.
4 Press TALK button once again, and after the beep,
communication ends.
5 Press TALK button again momentarily, and after the beep,
communication ends.
NOTES: Communication (video) ends automatically after approx. 1 minute.
NOTES: If the blue and white wires of the option connector are
shorted, PTT mode will not be operable.
8-2 Activating door release
1 During communication, instant voice call or entrance monitoring,
2 Press CALL button.
press MENU/MEMO button to display the menu screen.
PRESS
THE TALK
NOTES: When SET DOOR RELEASE setting is set
to
"Not use", the release symbol
is not displayed and the release cannot be
performed. (Refer to section 7-8)
BUTTO
N TO END.
PRESS THE TALK BUTTON TO END
3 Open door while the release mechanism is activated. During activation of door
PRESS THE TALK BUTTON TO END
release, the release symbol is displayed.
PRESS THE TALK BUTTON TO END
- 10 -
EFD.qxd 08.1.18 4:18 PM ページ 11
8-3 Message for entrance
1 During communication, instant voice call or entrance
3 Press either CALL button or PLAY button. The selected Message changes
to yellow, "SENDING MESSAGE" is displayed, and the selected message
is played from door station.
monitoring, press MENU/MEMO button to display the
menu screen.
THE TALK
BUTTO
N TO END.
SEND MESSAGE FOR ENTRANCE
2 Press PLAY button.
SENDING MESSAGE
English
PRESS
NOTES: Record separate messages in advance for Message 1 and
Message 2. (Refer to section 7-6)
Français
PRESS THE TALK BUTTON TO END
8-4 Entrance monitoring
3
Press MONITOR button again to switch to door station 2. Each time MONITOR
button is pressed, the unit switches in the sequence "Standby" to "Door station 1
monitor" to "Door station 2 monitor" to "Standby".
When
"Audio door station" or
"Door station 2 not connected"
is set in the door station 2 setting, "Door station 2 monitor" is skipped (door
station 2 cannot be monitored). (Refer to section 7-7)
2 The video monitor displays the image from door
station 1 and the incoming audio is heard. If you
do not press TALK button, the caller will not hear
sounds from the inside station.
4 Press MONITOR button again to end.
NOTES: 1. To talk to the entrance during monitoring, momentarily press TALK button.
Press TALK button again to end communication.
2. The entrance monitoring turns off automatically after approx. 1 minute. To
monitor the entrance again, repeat from the beginning.
8-5 Room-to-room communication
1 Press CALL button to talk with the other person.
3 Press and release TALK button to end.
• CALL button (red) flashes and the "All Call" function is
activated to link all the master/sub stations.
• The reply of the other person is not heard.
2 If the other person presses TALK button, hands-free
communication is possible.
Do not press TALK button during communication.
It will end the commnication.
NOTES: 1. Room-to-room communication ends automatically after approx. 10 minutes.
To perform room-to-room communication again, repeat from the beginning.
2. If a call is received from the entrance during room-to-room communication,
a chime tone sounds from the monitor station and sub station where
communication is taking place. Press TALK button to end the room-to-room
communication, and press TALK button again to switch to communication
with door station from which the call was received.
- 11 -
Nederlands
1 Press MONITOR button in the standby mode.
EFD.qxd 08.1.18 4:18 PM ページ 12
8-6 Transfer entrance call
English
1 During communication with door station, press CALL button to call
3 If TALK button is pressed at the transferred station, communication
the transferring station.
• CALL button (red) flashes and the communication with door station
is put on hold.
• The "All Call" function is activated to link all the master/sub stations.
NOTES: 1. If TALK button is pressed at the transferring station before starting
communication between the transferred station and door station, the
unit enters the condition where the forwarding source communicates
with door station. After ending the room-to-room communication in
step 2, TALK button must not be pressed at the transferring station for
a while (until the transferred station enters communication with door
station).
2. Communication (video) with door station ends automatically approx.
1 minute after first starting the communication.
Press TALK button within 30 seconds to start it again.
2 If TALK button is pressed at the transferred station, the unit enters
room-to-room communication. The sender informs the receiver that
communication will be transferred, and TALK button is pressed and
released at either the transferring station or transferred station to end
the room-to-room communication. (The screen continues to display
the image of door station.)
Nederlands
Français
with door station is performed (the transferring station's screen goes off).
Press TALK button to end communication.
8-7 Automatic recording
If a call is received from video door station, the unit starts recording automatically. The record LED (red)
flashes during recording (JF-2MED only).
• The recording starts approx. 2 seconds after CALL button of video door station is pressed. A maximum
length of approx. 8 seconds (8 shots) can be recorded with 1 picture and 1 shot for each second.
• A maximum of 50 pictures can be recorded (combined total of automatic recording and manual
recording pictures). If 50 pictures are exceeded, pictures are overwritten starting from the picture with
the oldest recording date.
NOTES: 1. The automatic recording function cannot be cancelled.
2. The screen shown when monitoring the entrance is not recorded automatically.
If you wish to record this screen, press REC button.
8-8 Manual recording
1 Display a video image with an operation such as entrance monitoring.
2 Press REC button. The record LED (red) flashes and recording starts.
NOTES: 1. Manual recording is not possible during automatic recording (approx.
9 seconds after receiving a call from door station).
2. After the end of automatic recording (approx. 9 seconds have passed
after receiving a call from the door station), another picture different
from the automatically recorded picture is recorded.
- 12 -
• A maximum length of approx. 8 seconds (8 shots) can be recorded
with 1 picture and 1 shot for each second.
• A maximum of 50 pictures can be recorded (combined total of
automatic recording and manual recording pictures). If 50 pictures are
exceeded, pictures are overwritten starting from the picture with the
oldest recording date.
EFD.qxd 08.1.18 4:18 PM ページ 13
8-9 Play recorded picture
If there are automatically recorded pictures, such as those taken while
you were out, the play LED (red) flashes.
Displayed when picture is unread
(not displayed after playing)
Displayed when picture is saved
(Refer to section 8-10)
3/16
2006
02 DEC
18 : 45
Sequence number of
picture currently being
displayed/total recorded pictures
Time and date of recording
2 Press PLAY button on the play screen. The recorded picture is played.
When the play of 1 picture ends, the next image is displayed.
Display during play
3/16
3/16
2006
02 DEC
18 : 45
2006
02 DEC
18 : 45
PRESS THE TALK BUTTON TO END
Number of
recorded pictures
PRESS THE TALK BUTTON TO END
3 To advance the play frame-by-frame, press PLAY button during
playback to pause. The play moves forward frame-by-frame each
time REC button is pressed. When the frames of 1 picture end, the
next picture is displayed.
3/16
3/16
2006
02 DEC
18 : 45
∗ In addition, the operations shown below are also possible during
pause.
• CALL button:
The play is reversed frame by frame each time the button is pressed.
When the frames of 1 picture end, the unit returns to the playwaiting screen.
• PLAY button :
To return to the play screen.
• MENU/MEMO button:
To display the next picture in the play screen.
2006
02 DEC
18 : 45
PRESS THE TALK BUTTON TO END
PRESS THE TALK BUTTON TO END
NOTES: 1. If there are no operations for approx. 1 minute or more, it will end
automatically.
2. If a call is received from door station during play, the chime tone
sounds and the play is forcibly ended.
4 Press TALK button to end.
8-10 Save recorded picture
10 pictures can be saved from the recorded pictures (maximum
of 50 pictures). Saved pictures are not overwritten.
1 Display the picture that you want to save in the play screen.
2
Press CALL button. If the picture is saved, the key symbol is displayed.
If the picture has already been saved, the save is canceled. Each time
CALL button is pressed, the operation switches between save and cancel.
3/16
(Refer to section 8-9)
Press MENU/MEMO button to display the save/erase
selection screen.
2006
02 DEC
18 : 45
3/16
SAVE/ERASE
2006
02 DEC
18 : 45
∗ In addition, the operations shown below are also
possible in the save/erase selection screen.
• REC button:
To erase the display picture. (Refer to section 8-11)
• MENU/MEMO button:
To return to the play screen.
PRESS THE TALK BUTTON TO END
3/16
NOTES: 1. "CANNOT SAVE" is displayed if the number of possible saves is
exceeded. Cancel unnecessary saved picture.
2. Pictures that have had the save canceled are not erased, but they are
overwritten if the number of recorded pictures is exceeded.
- 13 -
Nederlands
∗ The operations shown below are possible during play.
• CALL button:
To stop playing the picture and display the next picture.
• PLAY button :
To pause play.
• REC button:
To display the next picture after the end of fast forward playing.
PRESS THE TALK BUTTON TO END
Français
Display of door stations 1 and 2
Blue is door station 1
and yellow is door station 2
English
1 Press PLAY button in the standby mode to display the play screen.
∗ In addition, the operations shown below are also possible in the play
screen.
• CALL button:
To display the previous (more recent date) picture. When the button
is pressed for 1 second or more, during the time that the button is
pressed the first picture only of the dates can be checked in
succession, from older to more recent dates.
• REC button:
To display the next (older date) picture. When the button is pressed
for 1 second or more, during the time that the button is pressed the
first picture only of the dates can be checked in succession, in the
direction of the older dates.
• MENU/MEMO button:
To save or erase a picture. (Refer to sections 8-10 and 8-11)
When there are multiple unread pictures, all pictures enter the read
condition even if only 1 picture is played, and the play LED goes
off.
EFD.qxd 08.1.18 4:18 PM ページ 14
8-11 Erase recorded picture
It is also possible to erase saved recorded pictures.
The erasure of recorded pictures is performed for each picture in turn.
2 Press REC button.
3/16
2006
02 DEC
18 : 45
English
1 Display the picture that you want to erase in the play screen.
(Refer to section 8-9)
Press MENU/MEMO button to display the save/erase selection
screen.
SAVE/ERASE
3 Press CALL button to erase.
3/16
Press PLAY button to stop the erasure and return to the play screen.
2006
02 DEC
18 : 45
Once a picture is erased, it cannot be restored.
PRESS THE TALK BUTTON TO END
3/16
Français
2006
02 DEC
18 : 45
DO YOU WANT TO ERASE PICTURE?
Nederlands
8-12 Recording Voice memos
JF-2MED
Voice memos for internal use can be recorded.
A maximum of 3 memos can be recorded (maximum of approx. 15
seconds per memo).
4 Press CALL button to end the recording.
Alternatively, it ends automatically after approx. 15 seconds have passed.
1 Press MENU/MEMO button in the standby mode.
RECORDING (8 SEC. REMAINING)
5 Press CALL button to check the recording results.
Press PLAY button to stop the play and return to the Voice memo
selection screen.
2 Select Voice memo with CALL button.
Unplayed symbol
Displayed for Voice memos
that have never been played.
Each time CALL button is pressed, the
cursor switches between A, B, and C.
02 DEC 18:45
DO YOU WANT TO REPLAY MEMO?
SELECT
PLAY
REC
ERACE
6 Press TALK button to return to the standby mode.
3 Press REC button to record a Voice memo.
SELECT
PLAY
REC
NOTES: 1. If a Voice memo with an unplayed symbol is selected and REC
button is pressed the following is displayed: "DO YOU WANT TO
OVERWRITE MEMO?" To overwrite press CALL button, and to
abort press PLAY button.
2. The volume of Voice memos cannot be adjusted.
ERACE
8-13 Playing Voice memos
JF-2MED
If there are unplayed Voice memos, the memo LED (red) flashes.
3 Press PLAY button to play a memo.
1 Press MENU/MEMO button in the standby mode.
02 DEC 18:45
02 DEC 18:47
02 DEC 18:48
SELECT
PLAY
REC
ERACE
4 Press CALL button to end.
2 Select the Voice memo that you want to play with
Alternatively, it ends automatically after the playing finishes
(maximum of approx. 15 seconds).
CALL button. Each time CALL button is pressed, the
cursor switches between A, B, and C.
02 DEC 18:45
02 DEC 18:47
Unplayed symbol
Displayed for Voice memos
that have never been played.
02 DEC 18:45
02 DEC 18:47
02 DEC 18:48
SELECT
PLAY
REC
ERACE
Time and date of recording
02 DEC 18:48
PLAYING MEMO
5 Press TALK button to return to standby mode.
NOTES: 1. When the playing ends the unit returns to the memo selection screen
and the unplayed symbol goes off.
2. The volume of Voice memos cannot be adjusted.
- 14 -
EFD.qxd 08.1.18 4:18 PM ページ 15
8-14 Erasing Voice memos
JF-2MED
1 Press MENU/MEMO button in the standby mode.
3 Press MENU/MEMO button.
02 DEC 18:45
02 DEC 18:47
02 DEC 18:48
2 Select the memo that you want to erase with CALL
PLAY
REC
ERACE
4 Press CALL button to erase. Press PLAY button to stop the
English
SELECT
erasure and return to the Voice memo selection screen.
Once a Voice memo is erased, it cannot be restored.
button. Each time CALL button is pressed, the cursor
switches between A, B, and C.
02 DEC 18:45
02 DEC 18:45
02 DEC 18:47
02 DEC 18:48
02 DEC 18:48
DO YOU WANT TO ERASE MEMO?
SELECT
PLAY
REC
ERACE
Français
02 DEC 18:47
5 Press TALK button to return to the standby mode.
8-15 If optional units are installed
2 Press TALK button to stop the notification sound.
notification sound goes off and the transmit LED (red) flashes.
A warning screen is displayed on the video monitor.
rrrrr
The notification sound volume is linked with "Chime tone volume
control". When the chime tone volume control is turned "Off", the
notification sound does not go off. However, when the EXTERNAL
SENSOR INPUT is set to
, JF-2MED sounds at a volume
equivalent to "High" (fixed).
Prrr
NOTES: 1. The notification sound time is set in the EXTERNAL SENSOR INPUT. (Refer to section 7-9)
The factory setting is
.
2. When the EXTERNAL SENSOR INPUT is set to
, door station 1 also emits a notification sound. (Door station 2 does not go off a
notification sound.)
3. If a call is received from an entrance during the notification, the unit switches to the entrance call (communication is prioritized). However,
when the EXTERNAL SENSOR INPUT is set to
, the notification continues to sound even if there is a call from an entrance.
4. When the EXTERNAL SENSOR INPUT is set to
, there is automatic restoration after 30 seconds.
5. When the EXTERNAL SENSOR INPUT is set to
or
, the notification sound operates continuously until reset, however a
warning screen ends after approx. 1 minute.
9
TECHNICAL PRECAUTIONS
• Operating temperature: 0 °C to 40 °C (+32 °F to +104 °F)
• The video image may distort slightly during activation of
door release. But this is not a unit malfunction.
10
• Cleaning: Clean the units with a soft cloth dampened with a neutral
household cleanser. Do not use any abrasive cleaner or cloth.
• If there is a system malfunction, turn the Power switch at the monitor
station OFF and back ON again. If this does not solve the problem, unplug
the DC power supply and contact a qualified technician for service.
SPECIFICATIONS
• Power:
DC 18 V (JF-2MED, JF-2HD)
• Current consumption: (Max.) 400 mA (JF-2MED)
(Max.) 220 mA (JF-2HD)
• Calling:
Chime and image, approx. 45 seconds
• Communication:
(HANDS-FREE mode) Approx. 60 seconds
(PTT mode) Press-to-talk, release to listen, approx. 60 seconds
• Video monitor:
3-1/2" direct view TFT color LCD
• Scanning lines:
525 lines
• Door release contact: AC/DC 24 V, 0.5 A (N/O dry closure contact L, L)
(Aiphone's EL-9S is recommended.)
• Dimensions:
179 (H) x 135 (W) x 32 (D) (mm)
7" H x 5-5/16" W x 1-1/4" D
• Weight:
440 g (0.97 lbs.) approx. (JF-2MED)
420 g (0.93 lbs.) approx. (JF-2HD)
- 15 -
Nederlands
1 When a sensor is activated or a call button is pressed, the
EFD.qxd 08.1.18 4:18 PM ページ 44
WARRANTY
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy, and if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures: • Reorient or relocate the receiving antenna • Connect the equipment into an
outlet on a circuit different from that to which the receiver is connected. Increase the
separation between the equipment and receiver. • Consult the dealer or an experienced
radio/TV technician for help.
English
Aiphone warrants its products to be free from defects of material and workmanship
under normal use and service for a period of two years after delivery to the ultimate user
and will repair free of charge or replace at no charge, should it become defective upon
which examination shall disclose to be defective and under warranty. Aiphone reserves
unto itself the sole right to make the final decision whether there is a defect in materials
and/or workmanship; and whether or not the product is within the warranty. This
warranty shall not apply to any Aiphone product which has been subject to misuse,
neglect, accident, or to use in violation of instructions furnished, nor extended to units
which have been repaired or altered outside of the factory. This warranty does not cover
batteries or damage caused by batteries used in connection with the unit. This warranty
covers bench repairs only,and any repairs must be made at the shop or place designated
in writing by Aiphone. Aiphone will not be responsible for any costs incurred involving
on site service calls. Aiphone will not provide compensation for any loss or damage
incurred by the breakdown or malfunction of its products during use, or for any
consequent inconvenience or losses that may result.
The object area of
(WEEE) is EU.
GARANTIE
Français
Aiphone garantit que ses produits ne sont affecte's d'aucun défaut de matière ni de
fabrication, en cas d'utilisation normale et de réparations conformes, pendant une
période de deux ans après la livraison à l'utilisateur final,et s'engage à effectuer
gratuitement les réparations nécessaires ou à remplacer l'appareil gratuitement si celui-ci
présente un défaut, à la condition que ce défaut soit bien confirmé lors de l'examen de
l'appareil et que l'appareil soit toujours sous garantie. Aiphone se réserve le droit
exclusif de décider s'il existe ou non un défaut de matière ou de fabrication et si
l'appareil est ou non couvert par la garantie. Cette garantie ne s'applique pas à tout
produit Aiphone qui a été l'objet d'une utilisation impropre, de négligence, d'un accident
ou qui a été utilisé en dépit des instructions fournies; elle ne couvre pas non plus les
appareils qui ont été réparés ou modifiés en dehors de l'usine. Cette garantie ne couvre
pas les piles ni les dégâts infligés par les piles utilisées dans l'appareil. Cette garantie
couvre exclusivement les réparations effectuées en atelier. Toute réparation doit être
effectuée a l'atelier ou a l'endroit precisé par écrit par Aiphone. Aiphone décline toute
responsabilité en cas de frais encourus pour les dépannages sur site. Aiphone
n'indemnisera pas le client en cas de pertes, de dommages ou de désagréments causés
par une panne ou un dysfonctionnement d'un de ses produits.
La zone d'application de
(WEEE) est l'UE.
WAARBORG
Nederlands
Aiphone waarborgt zijn producten tegen materiaal- en fabricagefouten bij normal
gebruik en onderhoud gedurende een periode van twee jaar na levering aan de
eindgebruiker en zal het product kosteloos herstellen of vervangen indien na onderzoek
blijkt dat het defect en nog onder waarborg is. Aiphone behoudt zich het recht voor als
enige definitief te bepalen of er al dan niet sprake is van een materiaal-en/of
fabricagefout en of het product nog onder waarborg is. Deze waarborg geldt niet voor
om het even welk Aiphone-product dat is blootgesteld aan verkeerd gebruik,
verwaarlozing, een ongeval of verkeerde bediening en evenmin voor toestellen die
buiten de fabriek zijn hersteld of gewijzigd. Deze waarborg geldt niet voor batterijen of
schade veroorzaakt door batterijen die in het toestel zijn gebruikt. Deze waarborg dekt
uitsluitend werkbankherstellingen en iedere herstelling moet worden uitgevoerd in de
schriftelijk door Aiphone aangewezen winkel of werkplaats. Kosten die gepaard gaan
met herstellingen ter plaatse kunnen niet worden verhaald op Aiphone. Er kan geen
schadeloosstelling van Aiphone worden geëist voor enig verlies of schade als gevolg
van een defect of storing tijdens het gebruik van zijn producten, of voor enig ongemak
of verlies dat hieruit voortvloeit.
Het toepassingsgebied van
(WEEE) is de EU.
http://www.aiphone.com/
AIPHONE CO., LTD., NAGOYA, JAPAN
AIPHONE CORPORATION, BELLEVUE, WA, USA
AIPHONE S.A.S., LISSES-EVRY, FRANCE
Printed in Thailand
- 44 -