or G–Tan MAZDA PROX 2014 (ADS-225)

MVP - TCODE - PRO
Powered by ADVANCED DIAGNOSTICS USA
MAZDA PROX 2014
(ADS-225)
Models Covered:
(At time of printing)
2013-2015 CX-5
2014-2015 MAZDA 3
2014-2015 MAZDA 6
MVP & TCODE PRO
U.S. Patent #7315238
or
PIN
MVP
PRO
+
ADC250
or
ADC151
DONGLE
OUT-CODE / IN-CODE
DEALER or NASTF
ONLY
G–Tan
Also Requires
Smart Card
Or
Advanced Diagnostics
Web Challenge / Response
If Pro is not SMC enabled.
SEE WWW.ADUSA.US FOR INFO
2014 Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
MAZDA 2014- 1
MVP &
TCODE
MAZDA 2014
ADVANCED DIAGNOSTICS USA
powered
by
OVERVIEW
> A maximum of six remote transmitters (PROX) can be programmed to one vehicle.
>Two or more remote transmitters (PROX) must be programmed for the engine to start.
>If the engine is started during programming, the programming mode cancels. Therefore,
do not start the engine unless indicated in the procedure.
>Repeat the procedure from the beginning if the engine is started or the procedure is
interuppted.
>If any metallic or magnetic object is near the remote transmitter, communication between
the remote transmitter and the vehicle may be obstructed, resulting in a failure to program.
Remove any metallic or magnetic objects, such as key holders, from the remote
transmitter when programming.
Remote transmitter & E-Key
AKA PROX
Push to Start / Stop button
About Prox Keys
From what we have seen these Mazda Prox are re-usable from one car to another however, there are
several button configurations used depending on how the vehicle is equipped
I.E. Hatch, Trunk, etc. Always verify correct parts needed with a reputable supplier.
Immobilizer light / Indicator
When the vehicle is started theft light / indicator should be out.
Not blinking etc.
If the light is on or blinks when the car is turned on then the is a
problem with the key or with the immobilizer system.
2 - MAZDA 2014
2014 Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
powered
by
ADVANCED DIAGNOSTICS USA
MVP &
TCODE
ACURA / HONDA
SPECIAL FUNCTIONS MENU
DIAGNOSTIC MENU
FORCE IGNITION ON
Use this function when you have NO WORKING prox
Available.
FORCE IGNITION ON
CLEAR PROGRAM PROX
ADD PROX
To use CLEAR OR ADD PROX the Ignition must first be
placed in the ON position.
Use FORCE IGNITION ON to accomplish this FIRST before
doing anything else.
Once the Ignition is ON, leave it on and proceed to one of
the procedures below.
It is normal for the theft light to blink
while the Ignition has been forced on.
DIAGNOSTIC MENU
CLEAR PROGRAM PROX
Use this function to CLEAR all existing prox remotes from the
system and to PROGRAM TWO new ones.
You will need to have TWO prox remotes ready in order
to complete this procedure.
FORCE IGNITION ON
CLEAR PROGRAM PROX
ADD PROX
The Ignition MUST be placed in the ON position to begin so
either use FORCE IGNITION ON.
If you have a working prox use it to place the ignition in the
ON position.
ADD PROX
REQUIRES A MAZDA INCODE!
An IN-CODE is required to use this
software.
Must be obtained from a friendly Mazda
dealer or thru N.A.S.T.F. while at the job!
Use this function when you want to ADD a prox into the system without erasing any of the already programmed ones.
You will need to have ONE prox remote ready in order
to complete this procedure. However, the Prox will not
function completely until the engine is started with TWO
Prox remotes. Until the engine starts with TWO prox remotes the new prox will only start the engine when held
up to the Start/Stop button.
DIAGNOSTIC MENU
FORCE IGNITION ON
CLEAR PROGRAM PROX
ADD PROX
The Ignition MUST be placed in the ON position to begin so
either use FORCE IGNITION ON.
If you have a working prox use it to place the ignition in the
ON position.
2014 Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
MAZDA 2014- 3
MVP &
TCODE
MAZDA 2014
ADVANCED DIAGNOSTICS USA
powered
by
START HERE - IF NO WORKING PROX IS AVAILABLE
FORCE IGNITION ON PROCEDURE
Start by turning on the hazard lights
HAZARDS ON/ IGNITION OFF
Leave the Ignition in the OFF position
PRESS ENTER TO CONTINUE
PRESS ENTER KEY
ECU IDENTIFICATION
ECU ID SCREEN
SHOULD DISPLAY
MAZDA CX5 / 3 / 6
PRESS ENTER TO CONTINUE
PRESS ENTER KEY
DIAGNOSTIC MENU
Select SPECIAL FUNCTIONS
ECU IDENTIFICATION
>SPECIAL FUNCTIONS
PRESS ENTER TO CONTINUE
DIAGNOSTIC MENU
Select FORCE IGNITION ON
>FORCE IGNITION ON
CLEAR PROGRAM PROX
ADD PROX
THEN PRESS ENTER
FORCE IGNITION
Press and Release the Start Stop
Button
(For about a second)
THEN PRESS ENTER
4 - MAZDA 2014
PRESS & RELEASE START / STOP
BUTTON
PRESS ENTER KEY
2014 Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
powered
by
ADVANCED DIAGNOSTICS USA
MAZDA 2014
MVP &
TCODE
FORCE IGNITION
The light on the START / STOP Button
should turn ORANGE once it does
Press the START / STOP BUTTON
& the Ignition should turn ON.
Once it does, LEAVE IT ON.
WAIT FOR THE LIGHT ON
START / STOP BUTTON TO TURN
ORANGE THEN PRESS &
RELEASE START / STOP BUTTON
IGNITION SHOULD TURN ON
YOU MAY SKIP THE “FORCE IGNITION ON” PRECEDURE
IF YOU HAVE A WORKING PROX AVAILABLE.
ONCE YOU HAVE COMPLETED THE “FORCE IGNITION ON” PROCEDURE
THE DASH SHOULD BE FULLY ON AND THE THEFT LIGHT
SHOULD BE BLINKING RAPIDLY
SEE NEXT PAGES >>>>>
2014 Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
MAZDA 2014- 5
MVP &
TCODE
MAZDA 2014
powered
by
ADVANCED DIAGNOSTICS USA
CLEAR PROGRAM PROX PROCEDURE
SWITCH THE IGNITION “ON”
OR FORCE THE IGNITION ON PRIOR TO BEGINNING!
CLEAR PROGRAM PROX
Erases ALL currently programmed Prox
and programs in TWO Prox.
DIAGNOSTIC MENU
SELECT CLEAR PROGRAM PROX
Make sure you have 2 Prox keys
ready to Program!
FORCE IGNITION ON
> CLEAR PROGRAM PROX
ADD PROX
MAKE SURE THE IGNITION IS ON!
CLEAR KEYS
Press the Check mark if you
want to continue
Or
Press the X if you want to abort.
WARNING
ALL KEYS WILL
BE CLEARED
CONTINUE
X
4
GAINING ACCESS
USE THE OUTCODE TO OBTAIN
AND INCODE FROM MAZDA.
OUTCODE: 17 68 2C
(EXAMPLE ONLY!)
ONCE YOU HAVE OBTAINED THE
INCODE PRESS ENTER TO CONTINUE
PRESS ENTER KEY
STAY CONNECTED WHILE YOU OBTAIN THE INCODE
IF YOU DISCONNECT YOU WILL HAVE TO START OVER!
IN-CODE
Carefully
Enter the 4-Digit
IN-CODE
____
1
6
2
7
3
8
4
9
5
0
CONTINUED ON NEXT PAGE >>>>>
6 - MAZDA 2014
2014 Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
powered
by
ADVANCED DIAGNOSTICS USA
MVP &
TCODE
MAZDA 2014
CLEAR PROGRAM PROX PROCEDURE
CONTINUED’
IN-CODE
To change to letters on
the keypad use the left
and right arrow keys.
____
A
F
B
G
Once you have entered the INCODE
IN-CODE
Select the check Mark to continue
or the X to abort.
C
H
D
I
E
J
900B
(EXAMPLE ONLY)
X
4
PROGRAM PROX
THE NEXT SCREEN SHOULD SHOW
THAT ALL KEYS HAVE BEEN
CLEARED
KEYS PROGRAMMED : 00
2 KEYS REQUIRED
PRESS ENTER TO CONTINUE
PRESS ENTER KEY
PROGRAM PROX
PRESS THE START / STOP
BUTTON TO TURN THE IGNITION OFF
PRESS THE START / STOP
BUTTON TO SWITCH THE IGNITION
OFF
THEN PRESS ENTER TO CONTINUE
PRESS ENTER KEY
CONTINUED ON NEXT PAGE >>>>>
2014 Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
MAZDA 2014- 7
MVP &
TCODE
MAZDA 2014
ADVANCED DIAGNOSTICS USA
powered
by
CLEAR PROGRAM PROX PROCEDURE
CONTINUED’
PROGRAM PROX
DO NOT PRESS THE BRAKE PEDAL
PRESS THE START / STOP BUTTON TO
TURN THE IGNITION ON
WITHIN 10 SECONDS HOLD THE 1ST
PROX OVER THE START / STOP
BUTTON WITH THE MAZDA LOGO
FACING YOU
Perform this step as shown above.
The reason NOT to depress the brake pedal is we do NOT want the engine to start.
PROGRAM PROX
THE SCREEN SHOULD NOW DISPLAY
KEYS PROGRAMMED: 1
AND
ASK YOU TO TURN THE IGNITION OFF
KEYS PROGRAMMED: 1
PRESS THE START / STOP
BUTTON TO SWITCH THE IGNITION
OFF
REPEAT THE PROCESS TO PROGRAM IN THE 2ND PROX.
PROGRAM PROX
DO NOT PRESS THE BRAKE PEDAL
PRESS THE START / STOP BUTTON TO
TURN THE IGNITION ON
WITHIN 10 SECONDS HOLD THE 1ST
PROX OVER THE START / STOP
BUTTON WITH THE MAZDA LOGO
FACING YOU
CONTINUED ON NEXT PAGE >>>>>
8 - MAZDA 2014
2014 Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
powered
by
MVP &
TCODE
MAZDA 2014
ADVANCED DIAGNOSTICS USA
CLEAR PROGRAM PROX PROCEDURE
CONTINUED’
PROGRAM PROX
THE SCREEN SHOULD NOW DISPLAY
KEYS PROGRAMMED: 2
AND
ASK YOU TO TURN THE IGNITION OFF
KEYS PROGRAMMED: 2
PRESS THE START / STOP
BUTTON TO SWITCH THE IGNITION
OFF
PROGRAM PROX
TO COMPLETE THE PROCEDURE
START THE ENGINE WHILE HOLDING
EACH PROX UP TO THE START / STOP
BUTTON
IT’S VERY IMPORTANT TO PERFORM THIS STEP!
UNTIL EACH PROX STARTS THE VEHICLE
THEY WILL NOT OPERATE PROPERLY.
PRESS ENTER KEY
IF FOR ANY REASON 2 PROX DID NOT SUCCESSFULLY PROGRAM REPEAT THE PROCESS
OF HOLDING UP THE PROX SHOWN ON THE PREVIOUS PAGE UNTIL BOTH PROX OPERATE
AND START THE ENGINE.
ADD PROX PROCEDURE
The ADD PROX procedure is essentially the same as the CLEAR PROGRAM PROCEDURE
EXCEPT it does not ERASE any previously programmed PROX and only programs 1 NEW Prox.
IMPORTANT:
Before ADDING a PROX make sure you have at least one of the 2 already working PROX available.
This is because of the way MAZDA designed the system.
Remember, before any PROX that has been added will work properly the engine MUST be started with
TWO prox keys.
If you ADD a Prox but DO NOT have the other PROX available the new prox will work and start the engine
but only by holding it up to the start / stop button.
The process can be completed later by starting the engine with the other prox but this is something to
be aware of as your customer will likely NOT be happy until everything works as designed.
2014 Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.
MAZDA 2014- 9
MVP &
TCODE
MAZDA 2014
ADVANCED DIAGNOSTICS USA
powered
by
99
99
99
Helpful tip for filling out the MAZDA info:
Insert 99 into the fields shown above.
Insert the OUT-CODE displayed on the PRO without any spaces:
Example: ABCD12
10 - MAZDA 2014
2014 Advanced Diagnostics USA Manual for MVP & TCODE PRO – Copyright 2014 Advanced Diagnostics USA INC.